Noise in Hydraulic

Contents
[hide]
• 1 Noise in Hydraulic Systems

• 2 Sound in fluids
• 3 Source of Noise
• 4 Fluidborne Noise (FBN)
• 5 Structureborne Noise (SBN)
• 6 Transmission
o 6.1 FBN
o 6.2 SBN
• 7 Airborne noise (ABN)
• 8 Noise reduction
• 9 Hydraulic System noise
• 10 References
[edit] Noise in Hydraulic Systems

Hydraulic systems are the most preferred source of power transmission in most of the
industrial and mobile equipments due to their power density, compactness, flexibility,
fast response and efficiency. The field hydraulics and pneumatics is also known as
'Fluid Power Technology'. Fluid power systems have a wide range of applications
which include industrial, off-road vehicles, automotive systems, and aircraft. But, one
of the main problems with the hydraulic systems is the noise generated by them. The
health and safety issues relating to noise have been recognized for many years and
legislation is now placing clear demands on manufacturers to reduce noise levels [1].
Hence, noise reduction in hydraulic systems demands lot of attention from the industrial
as well as academic researchers. It needs a good understanding of how the noise is
generated and propagated in a hydraulic system in order to reduce it.
[edit] Sound in fluids

The speed of sound in fluids can be determined using the following relation.
where K - fluid bulk modulus, ρ- fluid density, c - velocity of sound
Typical value of bulk modulus range from 2e9 to 2.5e9 N/m2. For a particular oil, with
a density of 889 kg/m3,
speed of sound
[edit] Source of Noise

The main source of noise in hydraulic systems is the pump which supplies the flow.
Most of the pumps used are positive displacement pumps. Of the positive displacement
pumps, axial piston swash plate type is mostly preferred due to their reliability and
efficiency.
The noise generation in an axial piston pump can be classified under two categories (i)
fluidborne nose and
(ii) Structureborne noise
[edit]
Fluidborne Noise (FBN)
Among the positive displacement pumps, highest levels of FBN are generated by axial
piston pumps and lowest levels by screw pumps and in between these lie the external
gear pump and vane pump [1]. The discussion in this page is mainly focused on axial
piston swash plate type pumps. An axial piston pump has a fixed number of
displacement chambers arranged in a circular pattern separated from each other by an
angular pitch equal to where n is the number of displacement chambers. As

each chamber discharges a specific volume of fluid, the discharge at the pump outlet is
sum of all the discharge from the individual chambers. The discontinuity in flow
between adjacent chambers results in a kinematic flow ripple. The amplitude of the
kinematic ripple can be theoretical determined given the size of the pump and the
number of displacement chambers. The kinematic ripple is the main cause of the
fluidborne noise. The kinematic ripples is a theoretical value. The actual flow ripple at
the pump outlet is much larger than the theoretical value because the kinematic ripple
is combined with a compressibility component which is due to the fluid
compressibility. These ripples (also referred as flow pulsations) generated at the pump
are transmitted through the pipe or flexible hose connected to the pump and travel to all
parts of the hydraulic circuit.
The pump is considered an ideal flow source. The pressure in the system will be
decided by resistance to the flow or otherwise known as system load. The flow
pulsations result in pressure pulsations. The pressure pulsations are superimposed on the
mean system pressure. Both the flow and pressure pulsations easily travel to all part of
the circuit and affect the performance of the components like control valve and
actuators in the system and make the component vibrate, sometimes even resonate. This
vibration of system components adds to the noise generated by the flow pulsations. The
transmission of FBN in the circuit is discussed under transmission below.
A typical axial piston pump with 9 pistons running at 1000 rpm can produce a sound
pressure level of more than 70 dBs.
[edit]
Structureborne Noise (SBN)
In swash plate type pumps, the main sources of the structureborne noise are the
fluctuating forces and moments of the swash plate. These fluctuating forces arise as a
result of the varying pressure inside the displacement chamber. As the displacing
elements move from suction stroke to discharge stroke, the pressure varies accordingly
from few bars to few hundred bars. This pressure changes are reflected on the
displacement elements (in this case, pistons) as forces and these force are exerted on the
swash plate causing the swash plate to vibrate. This vibration of the swash plate is the
main cause of structureborne noise. There are other components in the system which
also vibrate and lead to structureborne noise, but the swash is the major contributor.
Fig. 1 shows an exploded view of axial piston pump. Also the flow pulsations and
the oscillating forces on the swash plate, which cause FBN and SBN respectively
are shown for one revolution of the pump.
[edit] Transmission
[edit] FBN
The transmission of FBN is a complex phenomenon. Over the past few decades,
considerable amount of research had gone into mathematical modeling of pressure and
flow transient in the circuit. This involves the solution of wave equations, with piping
treated as a distributed parameter system known as a transmission line [1] & [3].
Lets consider a simple pump-pipe-loading valve circuit as shown in Fig. 2. The pressure
and flow ripple at any location in the pipe can be described by the relations:
.........(1)
.....(2)
where and are frequency dependent complex coefficients which are directly
proportional to pump (source) flow ripple, but also functions of the source impedance
, characteristic impedance of the pipe and the termination impedance . These
impedances ,usually vary as the system operating pressure and flow rate changes, can be
determined experimentally.
Image:Pump pipe circuit. jpg
Fig.2 Schematic of a pump connected to a hydraulic line
For complex systems with several system components, the pressure and flow ripples are
estimated using the transformation matrix approach. For this, the system components
can be treated as lumped impedances (a throttle valve or accumulator), or distributed
impedances (flexible hose or silencer). Various software packages are available today to
predict the pressure pulsations.
[edit] SBN
The transmission of SBN follows the classic source-path-noise model. The vibrations of
the swash plate, the main cause of SBN, are transferred to the pump casing which
encloses all the rotating group in the pump including displacement chambers (also
known as cylinder block), pistons, and the swash plate. The pump case, apart from
vibrating itself, transfers the vibration down to the mount on which the pump is
mounted. The mount then passes the vibrations down to the main mounted structure or
the vehicle. Thus the SBN is transferred from the swash plate to the main structure or
vehicle via pumpcasing and mount.
Some of the machine structures, along the path of transmission, are good at transmitting
this vibrational energy and they even resonate and reinforce it. By converting only a
fraction of 1% of the pump structureborne noise into sound, a member in the
transmission path could radiate more ABN than the pump itself [4].
[edit] Airborne noise (ABN)

Both FBN and SBN , impart high fatigue loads on the system components and make
them vibrate. All of these vibrations are radiated as airborne noise and can be heard by
a human operator. Also, the flow and pressure pulsations make the system components
such as a control valve to resonate. This vibration of the particular component again
radiates airborne noise.
[edit] Noise reduction

The reduction of the noise radiated from the hydraulic system can be approached in two
ways.
(i) Reduction at Source - which is the reduction of noise at the pump. A large amount
of open literature are available on the reduction techniques with some techniques
focusing on reducing FBN at source and others focusing on SBN. Reduction in FBN
and SBN at the source has a large influence on the ABN that is radiated. Even though, a
lot of progress had been made in reducing the FBN and SBN separately, the problem of
noise in hydraulic systems is not fully solved and lot need to be done. The reason is that
the FBN and SBN are interrelated, in a sense that, if one tried to reduce the FBN at the
pump, it tends to affect the SBN characteristics. Currently, one of the main researches in
noise reduction in pumps, is a systematic approach in understanding the coupling
between FBN and SBN and targeting them simultaneously instead of treating them as
two separate sources. Such an unified approach, demands not only well trained
researchers but also sophisticated computer based mathematical model of the pump
which can accurately output the necessary results for optimization of pump design.
(ii) Reduction at Component level - which focuses on the reduction of noise from
individual component like hose, control valve, pump mounts and fixtures. This can be
accomplished by a suitable design modification of the component so that it radiates least
amount of noise. Optimization using computer based models can be one of the ways.
[edit] Hydraulic System noise
Fig.3 Domain of hydraulic system noise generation and transmission (Figure

recreated from [1])
[edit] References
1. Designing Quieter Hydraulic Systems - Some Recent Developments and
Contributions, Kevin Edge, 1999, Fluid Power: Forth JHPS International Symposium.
2. Fundamentals of Acoustics L.E. Kinsler, A.R. Frey, A.B.Coppens, J.V. Sanders.

Fourth Edition. John Wiley & Sons Inc.
3. Reduction of Axial Piston Pump Pressure Ripple A.M. Harrison. PhD thesis,
University of Bath. 1997
4. Noise Control of Hydraulic Machinery Stan Skaistis, 1988. MARCEL DEKKER ,
INC.

Noise in Hydraulic

Uploaded by

Copyright:

Available Formats

Noise in Hydraulic

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Noise in Hydraulic

Uploaded by

Copyright:

Available Formats

Contents

• 1 Noise in Hydraulic Systems

[edit] Noise in Hydraulic Systems

[edit] Sound in fluids

where K - fluid bulk modulus, ρ- fluid density, c - velocity of sound

[edit] Source of Noise

(ii) Structureborne noise

angular pitch equal to where n is the number of displacement chambers. As

Image:Pump pipe circuit. jpg

Fig.2 Schematic of a pump connected to a hydraulic line

[edit] Airborne noise (ABN)

[edit] Noise reduction

[edit] Hydraulic System noise

Fig.3 Domain of hydraulic system noise generation and transmission (Figure

2. Fundamentals of Acoustics L.E. Kinsler, A.R. Frey, A.B.Coppens, J.V. Sanders.

You might also like