Ball Mill Manual F

1
INDEX
SR NO SUBJECT PAGE NO
1. Ball mill Diagram 2

2. Theory 3–5
3. Advantages & Disadvantages 6
4. Experimental Manual 7 – 10
5. Ball Mill Detailed Diagram 11
6. Ball Mill Wiring Diagram 12
BALL MILL EXPERIMENTAL MANUAL

2

3
BALL MILL DIAGRAM

THEORY:
In its simplest form, the Ball Mill consists of a rotating hollow cylinder, partially
filled with balls, with its axis either horizontal or at a small angel to the
horizontal. The material to be ground may be fed in through a hollow trunnion
at one end and the product leaves through a similar trunnion at the other end
for continuous type operation. The outlet is normally covered with a coarse
screen to prevent the escape of the balls.
The inner surface of the cylinder is usually lined with an abrasion-resistant

material such as manganese steel, stoneware or rubber. Less wear takes
place in rubber-lined mills, and the coefficient of friction between the balls and
the cylinder is greater than with steel or stoneware linings. The balls are
therefore carried further in contact with the cylinder and thus drop on to the
feed from a greater height. In some cases, lifter bars are fitted to the inside of
the cylinder. A new type of ball mill is now being used to an increasing extent,
where the mill is vibrated instead of being rotated, and the slope of the mill
controls the rate of passage of material.
The ball mill is used for the grinding of a wide range of materials, including
coal, pigments, and felspar for pottery, and will take feed up to about 50 mm
in size. The efficiency of grinding increases with the hold-up in the mill, until
the voids between the balls are filled. Further increase in the quantity then
lowers the efficiency again.
The balls are usually made of flint or steel and occupy between 30 and 50 per
cent of the volume of the mill. The diameter of ball used will vary between 13
mm and 125 mm and the optimum diameter is approximately proportional to
the square root of the size of the feed, the proportionality constant being a
function of the nature of the material.
During grinding, the balls themselves wear and are constantly replaced by
new ones so that the mill contains ball of various ages, and hence of various
sizes. This is advantageous since the large balls deal effectively with the feed
and the small ones are responsible for giving a fine product. The maximum
rate of wear of steel balls, using very abrasive materials, is about 0.3 kg per
mg of material for dry grinding, and 1-1.5 kg/mg for wet grinding. The normal
charge of balls amounts to about 5 mg/m 3. In small mills where very fine
grinding is required, pebbles are often used in place of balls.
In the compound mill, the cylinder is divided into a number of compartments

by vertical perforated plates. The material flows axially along the mill and can
pass from one compartment to the next only when its size has been reduced
to less than that of the perforations in the plate. Each compartment is supplied
with balls of a different size; the large balls are at the entry end and thus

4
operate on the feed material, whilst the small balls come into contact with the
material immediately before it is discharged. This results in economical
operation and the formation of a uniform product. It also gives an improved
residence time distribution for the material, since a single ball mill
approximates closely to a completely mixed system.
Factors influencing the size of the product:

(a) The rate of feed. With high rates of feed, less size reduction is
effected since the material is in the mill for a shorter time.
(b) The properties of the feed material. The larger the feed the larger will
be the product under given operating conditions. A smaller size
reduction is obtained with a hard material.
(c) Weight of balls. A heavy charge of balls produces a fine product. The
weight of the charge can be increased, either by increasing the
number of balls, or by using a material of higher density. Since
optimum grinding conditions are usually obtained when the bulk
volume of the balls is equal to 50 per cent of the volume of the mill,
variation of the weight of balls is normally effected by the use of
materials of different densities.
(d) The diameter of the balls. Small balls facilitate the production of fine
material but they do not deal so effectively with the larger particles in
the feed. The limiting size reduction obtained with a given size of
balls is known as the free grinding limit. For most economical
operation, the smallest possible balls should be used.
(e) The slope of the mill. Increase in the slope of the mill increases the
capacity of the plant because the retention time is reduced, but a
coarser product is obtained.
(f) Discharge freedom. Increasing the freedom of discharge of the
product has the same effect as increasing the slope. In some mills,
the product is discharged through openings in the lining.
(g) The speed of rotation of the mill. At low speed of rotation, the balls
simply roll over one another and little crushing action is obtained. At
slightly higher speeds, they are projected short distances across the
mill, and at still higher speeds they are thrown greater distances and
considerable wear of the lining of the mill takes place. At very high
speeds, the balls are carried right round in contact with the sides of
the mill and little relative movement of grinding takes place again.
The minimum speed at which the balls are carried round in this
manner is called the critical speed of the mill and, under these
conditions, there will be no resultant force acting on the ball when it
is situated in contact with the lining of the mill in the uppermost
position, that is the centrifugal force will be exactly equal to the
weight of the ball. If the mill is rotating at critical angular velocity (C),
r C2 = g
C =  g/ r
(h) The corresponding critical rotational speed N c = C / (2 * ) = [1/ (2 *
)] *  (g / r)

5
(i) Here r is the radius of the mill less than that of the particle. It is found
that the optimum speed is between one-half and three-quarters of the
critical speed.
(J) The level of material in the mill. Maintaining a low level of material in
the mill reduces power consumption, and fitting a suitable discharge
opening for the product can control this most satisfactorily. If the level
of material is raised, the cushioning action is increased and power is
wasted by the production of an excessive quantity of undersize
material.

6
ADVANTAGES:
 It produces very fine powder (Particle size less than or equal to
10 microns).
 It is suitable for milling toxic materials since it can be used in a
completely enclosed form.
 Has a wide application.
 It is used in milling highly abrasive materials.
DISADVANTAGES:
 Contamination of product may occur as a result of wear and tear
which occurs principally from the balls and partially from the
casing.
 High machine noise level especially if the hollow cylinder is made
of metal, but much less if rubber id used.
 Relatively long time of milling.
 It is difficult to clean the machine after use.

7

AIM:
(1) To determine Critical Speed, Work Index, Bonds Law, Rittinger’s Law
and Kick’s Law.
(2) To determine the Surface Area generated for the given amount of
feed.
APPARATUS:
Ball Mill, Sieves, Sieve Shaker, Weighing Balance, Weight Box.
PROCEDURE:
 Perform the sieve analysis of the feed at first.
 Take measurements of the cylindrical shell and the metallic balls.
 Take known number of balls inside the cylinder.
 Charge the known weight of material to the mill, which is to be grind.
 Note the time t and start the ball mill for one or half hour.
 Take out the product and perform the sieve analysis.
OBSERVATION:
Quantity of feed sample =

Feed size, Df =
Time taken for 1 complete revolution (No load) =
Time taken for 1 complete revolution (Load) =
Total time the mill is put to operation =
Energy meter constant for ball mill = 1600

8
OBSERVATION TABLE:
Mesh Mean Mass Mass

Sr. Screen
Dia. Retained fraction Xi/Dpi
No. no. aperture
Dp, mm (1a+2a/2) gm Retained, Xi
1a.
2a.
3a.
4a.
5a.
6a.
7a.
8a.
9a.
10a.
11a.
12a.
13a.
14a.
CALCULATION:
1) Energy required for crushing
E = (n1 –n) / (m x EMC)
= (53.33 – 44.44) / (0.005 x 1600)
= 8.89 / 8
= 1.1112 kW hr/Tones
2) Work index
Wi = (E) / (1/ ʃ Dp – 1 ʃ Df)
= (1.1112) / (1 / 0.02 – 0.1)
= (1.1112) / (12.5)
= 0.0888

9
3) Reduction ratio = Z Feed size % Product size

= 0.1 - 0.02 X 1000
= 80 %
4) Critical speed of ball mill
Nc = ½ ᴫ (ʃ g / R-r)
= ½ x 3.14 (9.8 / 0.165 – 0.0125)
= 0.5 x 3.14 (9.8 / 0.1525)
= 0.5 x 3.14 (1.4945)
= 0.5 x 4.6927
= 2.3463
Where,
n1 is the no. of revolutions of the energy meter disc during the mill operation
under load condition = 53.33
n is the no. of revolutions of the energy meter disc during the mill operation
under no load condition = 44.44
m is mass of sample in tones = 0.005 tones
EMC is energy meter constant = 1600
Dp is mass mean diameter of the product sample in mm = 0.02 m
Df is the diameter of the feed sample in mm = 0.1 m
g is acceleration due to gravity in = 9.8 m/sec2
R is radius of the Ball mill in = 0.165 m
r is the radius of Balls in = 0.0125 m
Result:
Using the Ball mill experimental setup, the following were determined:
1. Energy required for crushing = 1.1112 kW hr/Ton

2. Work index = 0.0888 kW hr ʃ mm/Ton
3. Reduction ratio = 80 %
4. Critical speed of the ball mill = 2.3463 rps

10

11

Ball Mill Manual F

Uploaded by

Copyright:

Available Formats

Ball Mill Manual F

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ball Mill Manual F

Uploaded by

Copyright:

Available Formats

What is the theory behind how a ball mill works?

What is the theory behind how a ball mill works?

What are some advantages and disadvantages of using a ball mill?

What are some advantages and disadvantages of using a ball mill?

1

1. Ball mill Diagram 2

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

BALL MILL DIAGRAM

The inner surface of the cylinder is usually lined with an abrasion-resistant

In the compound mill, the cylinder is divided into a number of compartments

BALL MILL EXPERIMENTAL MANUAL

Factors influencing the size of the product:

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

Ball Mill, Sieves, Sieve Shaker, Weighing Balance, Weight Box.

Quantity of feed sample =

BALL MILL EXPERIMENTAL MANUAL

Mesh Mean Mass Mass

BALL MILL EXPERIMENTAL MANUAL

3) Reduction ratio = Z Feed size % Product size

1. Energy required for crushing = 1.1112 kW hr/Ton

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

BALL MILL EXPERIMENTAL MANUAL

You might also like