Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 58 views

    Arninge!: Shock Absorber For Ducati 1198 With Race Linkage

    Uploaded by

    Pier o.f.r.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Arninge!: Shock Absorber For Ducati 1198 With Race Linkage

    Uploaded by

    Pier o.f.r.
    58 views4 pages

    Original Title

    MI_DU343

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    58 views4 pages

    Arninge!: Shock Absorber For Ducati 1198 With Race Linkage

    Uploaded by

    Pier o.f.r.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    ⚠⚠ Warning!

    The DU343 Kit is designed for Ducati 1198


    equipped with a Ducati Race Linkage. This
    product shall not be installed on a standard
    Ducati 1198.

    Kit Contents
    Description Part No Pcs
    Shock absorber DU343 1
    Sticker Öhlins 01185-01 2
    Sticker memo notes 01185-04 2
    Owner’s manual 07242-05 1

    11 Note! 11 Note!
    Please note that there can be small differences Before you install this product, check the kit
    between your product and the images in contents. If anything is missing, please contact
    these instructions. an Öhlins dealer.

    11 Note! ⚠⚠ Warning!
    Please note that during storage and transport, Before you install this product, read the Öhlins
    especially at high ambient temperature, some Owner’s manual. This product is an important
    of the oil and grease used for assembly may part of the vehicle and the vehicle stability.
    leak and stain the packaging. This will not
    cause damage to the product, wipe off the
    excessive oil or grease with a cloth.

    Shock absorber for Ducati 1198 with Race Linkage

    du 343
    Mounting Instructions
    mounting instructions
    ⚠⚠ Warning! 3
    We strongly recommend to let an Öhlins dealer Remove the rubber plug and loosen the lower
    install this product. mount for the original shock absorber.

    ⚠⚠ Warning! 4
    If you work with a lifted vehicle, make sure that it Reinstall the left footpeg-bracket.
    is safely supported to prevent it from tipping over.
    5
    11 Note! Loosen the screw at the back of the lower side
    When you work with this product, see the covers (left and right).
    vehicle service manual for vehicle specific
    procedures and important data. 6
    Remove the right footpeg-bracket.
    11 Note!
    Before you install this product clean the vehicle. 7
    Remove the black cover for the exhaust pipe
    1 (right side).
    Put the motorcycle on a work stand so that the
    rear wheel barely touches the ground.

    2
    Loosen the left footpeg and leave it for now.

    2 4 3

    2
    mounting instructions
    8 12
    Disconnect the exup-cables. Install the ÖHLINS shock absorber and all
    parts in reverse order.
    9
    Remove the silencers, and the mid exhaust 11 Note!
    pipes. Lower the vehicle so that the suspension
    is slightly compressed before you tighten
    10
    the screws.
    Remove the bolts for the rocker arm. Begin
    with bolt A. Then lower the rear wheel/swing 13
    arm to remove bolt B. Finally remove bolt C Make sure that all removed parts are
    and remove the whole rocker arm. reinstalled in the same way as they were
    before the installation of the Öhlins shock
    11
    absorber.
    Lower the swing arm or raise the motorcycle to
    remove the original shock absorber. ✋✋ Caution!
    Make sure that you tighten all screws to the
    correct torque and that nothing fouls or restricts
    movement of the shock absorber/front fork/
    steering damper when the suspension is fully
    compressed or extended.

    8 10

    3
    adjustments
    Compression
    ⚠⚠ Warning! damping
    adjuster
    Before you ride/drive, always make sure that the
    setup is according to the recommended setup
    data. Read about adjustments and setting up
    in the Öhlins Owner’s Manual before you make
    any adjustments. Contact an Öhlins dealer if Rebound
    you have any questions about setting up. damping
    adjuster Spring
    preload
    adjuster

    Setup Data
    Length 288 mm
    Stroke 60 mm
    Rebound 16 clicks
    Compression 15 clicks
    Spring preload 15 mm
    Spring part no. 21041-34
    Spring rate 100 N/mm
    Spring free length 150 +0/ -3 mm

    Öhlins products are subject to To find the latest information Part no. MI_DU343_0
    continuous improvement and contact an Öhlins distributor. Issued 2014-02-17
    development, therefore, although Please contact Öhlins if you have
    these instructions include the most any questions regarding the
    up-to-date information available at contents in this document.
    the time of printing, minor updates
    may occur.

    © Öhlins Racing AB. All rights Öhlins Racing AB


    reserved. Any reprinting or Box 722
    unauthorized use without the written S-194 27 Upplands Väsby, Sweden
    permission of Öhlins Racing AB Phone +46 8 590 025 00
    is prohibited. fax +46 8 590 025 80

    You might also like