R4850G1 Rectifier User Manual V1.

3
Environmental Specifications

Item Specification
Operating temperature -40 °C to +75 °C （referring
to Figure 3）
(-40°F to +167°F)
Storage temperature -40 °C to +75 °C （not
packaged）
(-40°F to +167°F)
Efficiency The peak point is≥ 96%;
Relative humidity 5%-95% (non-condensing)
≥ 95%(230V AC,20%–90%
load) Altitude range ≤ 4000 m (13,123.2 ft)
Height x Width x 88.9 mm x 103 mm x 243 Note: If the altitude is between 3000 m (9842.4 ft) and 4000 m (13,123.2 ft), the
Depth mm temperature derates by 1 °C (1.8°F ) for each additional 200 m (656.2 ft).

(3.50 in. x 4.06 in. x 9.57 in.) Electrical Specifications

Weight ≤ 2.8 kg (6.17 lb)
Electrical Specification
Product Description Specifications
Input
The R4850G1 is a digital rectifier converts the 85
VAC ~300 VAC input to 53.5 VDC output that Operating voltage 85–300 VAC
possesses the characters of high efficiency，high
Frequency 45–66 Hz
power density, soft start, parallel, complete
protection, and low noise. Adopting the latest power Rated : 50Hz and 60 Hz
topology and latest intelligence control technology to Maximum input current ≤ 18.5 A
realize the high efficiency under widest load range.
Power factor ≥ 0.99 (50% load or more)
Key Features THD ≤ 5％ (50% load or more)

• Input voltage range: 85 VAC–300 VAC Output

• Operating temperature range: -40 °C to +75 °C Output voltage 43.2–58 .0VDC
(-40°F to +167°F) Default voltage: 53.5 VDC

• Total harmonic distortion (THD): ≤ 5％ Output power 3000 W (176–300 VAC);

1200 W (85–175 VAC)
• Hot plug
Regulated voltage ≤±0.6％Vo
• Digital control
precision
• Intelligent electric meter
Ripple and noise ≤ 200 mVp-p (Bandwidth ≤
• Communication over RS485 20MHz)
• LED display Static voltage regulation ±0.5% (from no load to 100%
load)
• Supports voltage adjustment,current adjustment,and
current sharing Dynamic regulation Over Shoot:≤ ±5％ Vo
• RE ,CE,ClassB Recovery time: ≤ 200us

• Active load sharing Standby power ≤ 5W

• Passing the TUV, CE, CB,UL certifications Turn-on output delay 3–8 s
• Online update the embedded software for future
need Hold up time >10 ms

• Meet Rohs requirement Psophometric noise ≤ 2 mV

• Disconnect above 320 VAC Broad frequency noise ≤ 50 mV (3.4–150 kHz)

• Patented high efficiency technology ≤ 20 mV (0.15M–30MHz)

HUAWEI TECHNOLOGIES CO., LTD.

1
R4850G1 Rectifier User Manual V1.3
Other Features
Item Specification Output Feature
Protection
Figure 1 Output feature
Input overvoltage Protection point:>300 VAC
protection
Recovery range:290 –300 VAC
Input undervoltage Protection point:<85 VAC
protection
Recovery range:85–90 VAC
Output overvoltage 58.5–60.5 VDC (can be set by
protection monitoring unit )
1.If the overvoltage occurs inside the
rectifier due to a fault, the rectifier will
latch off.
2.If the output voltage is higher than 63
V and lasts for more than 500 ms, the
rectifier will latch off.
Output current See Figure 1.
limiting protection

Output short circuit A long term short circuit is allowed. Figure 2 efficiency(Vin = 230 VAC,Ta:25 °C / 77
protection After the fault is rectified, the rectifier is °F)
restored to a healthy state
automatically.

Over-temperature The module protects against

protection overtemperature.
Safety/EMC/Lightening protection
Safety TUV, CE, UL CB
certification Complies with
UL60950-1;IEC60950-1;EN60950-
1;CAN/CSA C22.2 No. 60950 -1 ;
EMC EN55022 Class B ;
EN55024;
EN61000-3-2;
EN61000-3-3; Figure 3 Power derating curve
ETSI EN300 386;
ETSI EN301489;
ITU-T K.20;
Lightning 5KA
Reliability
MTBF > 500,000 hours
Audible Noise
Specification ≤ 50dB(25°C / 77 °F full load)

HUAWEI TECHNOLOGIES CO., LTD.

2
R4850G1 Rectifier User Manual V1.3

Interface Description Table 1 Definitions of the pins on the rear panel

The rear panel of the rectifier provides an AC input Pin Definition Function
socket and a DC output socket. PIN1–PIN16 on the
DC output socket function as a signal interface. For AC input pins
the location of the pins, see Figure 4. For the L Live Live line
definitions of the pins, see Table 1.
PE PE Protect earth
N N Neutral line
Figure 4 Pins on the rear panel
Signal pins
PIN1 ADDRESS0 Address
PIN2 ADDRESS1 Address
PIN3 LOADSHARE+ Share bus
PIN4 NC NC
PIN5 CURRENT Output current
LIMIT+ limiting
PIN6 SEC_GND Secondary GND
PIN7 ADDRESS2 Address
PIN8 ADDRESS3 Address
PIN9 NC NC
PIN10 NC NC
PIN11 NC NC
PIN12 RS485- RS485-
PIN13 ADDRESS4 Address
PIN14 NC NC
PIN15 RS485+ RS485+
PIN16 DC- Output 48V-
Pre- Pre-charge Pre-charge
charge
DC output pins
DC+ DC+ Output:48V+
DC- DC- Output:48V-

HUAWEI TECHNOLOGIES CO., LTD.

3
R4850G1 Rectifier User Manual V1.3

Transport
CAUTION The product must be packed with firmly packing
Only trained and qualified personnel can be allowed box when transport. Out of the box the mark
to install or service the rectifier. To avoid electric
“prevent moisture ”,”lay down carefully” and
shock or burning, wear antistatic clothes, antistatic
gloves, and ESD wrist straps before operating the other required mark must have. Any transport
rectifier. tools are permitted if the product in the packing
Each rectifier input is protected by two fuses, one box .When transport must avoid rain and snow
for the live wire and the other for the neutral wire. attack directly and mechanical shock.

Storage
Installing the Rectifier
Product should be packaged in the packing box
Figure 5 Procedure for installing the before use .The store room should be meet :-40
rectifier °C (-40°F) to +70 °C(158°F) ambient
temperature ,related humidity less than
80%,dry ,ventilation and hasn’t any corrosive
gas.

Step 1: Loosen the screws on the handle make

sure the handle on the front panel is
open and pull the handle and place the
rectifier in the appropriate slot. Then
push the rectifier make sure the pin and
the subrack is connected well.
Step 2:Close the handle
Step 3: Hold the handle and fix the screws on
the handle using screwdriver.

Removing the Rectifier

Figure 6 Procedure for removing the rectifier

Step 1: Loosen the screws on the handle using

an screwdriver.
Step 2: Pull the handle to disengage the
positioning pin on the front panel from
the subrack.
Step 3: Pull the rectifier out.

HUAWEI TECHNOLOGIES CO., LTD.

4
R4850G1 Rectifier User Manual V1.3
Maintenance

DANGER
• The high -voltage power supply energize equipment. Contacting the high-voltage power supply directly or through a dampened
object may cause you to death.
• Improper operations on the high-voltage power supply may cause accidents such as fire or electric shock.

Base on following suggestion, Simple fault can be dealt with .

Table 2 describes the states of LEDs and the causes for abnormal.

Indicator Color Status Description Measures

Run Green Steady on The rectifier output is normal. The rectifier runs properly, and no measure is
indicator required.
Off The rectifier has no output. Replace the rectifier if the AC input is normal.

Alarm Yellow Off No alarm is generated. No measure is required.

indicator
Steady on The rectifier generates a Check that the air vent is not blocked and the
prewarning for power limiting ambient temperature is within a normal range.
due to overtemperature.
The rectifier generates an
alarm for shutdown due to
ambient overtemperature
protection.

The rectifier generates an Check that the electrical grid voltage is within
alarm due to AC input a normal range.
overvoltage or undervoltage
protection.
The rectifier is hibernated. No measure is required.

Fault Red Off The rectifier is not faulty. No measure is required.

indicator
Steady on The rectifier is locked due to Pull out the rectifier and reinsert it after 1
output overvoltage. minute.
There is no output Replace the rectifier.
because the rectifier is faulty.
Blinking at 4 Hz The rectifier is loading an The rectifier automatically recovers after
application program. loading, and no measure is required.

Suggestions

1. Rectify the faults by referring to Table 2.

2. If you cannot rectify the fault according to Table 2, replace the rectifier.
3. Return the faulty rectifier to Huawei for repairing.
Huawei Technologies Co., Ltd.
Huawei Industrial Base
Bantian, Longgang, Shenzhen
518129
www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
5