Competency - Based Learning Materials: Metals and Engineering (Sector)

COMPETENCY - BASED LEARNING MATERIALS
METALS AND ENGINEERING

Sector:
( SECTOR )
Qualification:
SHIELDED METAL ARC WELDING NC II
Unit of Competency:
WELD CARBON STEEL PIPES USING SMAW
Module Title:
WELDING ON CARBON STEEL PIPES
Institution:
LMMSAT - TESDA
Poblacion West, Asingan, Pangasinan
LMMSAT - Shielded M etal Date Developed: Document N.

TESDA Arc W elding NC II
QA Issued by:
SYSTEM
Developed by: Revision Page _ of
No.
Jerry R. Torrado
LIST OF COMPETENCIES
No. Unit of Competency Module Title Code

Weld Carbon Steel Plates Welding Carbon Steel Plates
1. MEE721306
using SMAW using SMAW
Weld Carbon Steel Pipes Using Welding Carbon Steel Pipes
2. MEE721306
SMAW Using SMAW

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
HOW TO USE THIS COMPETENCY BASED LEARNING
MATERIAL
Welcome to the module in Welding Carbon Steel Pipes Using SMAW . This
module contains training materials and activities for you to complete.
The unit of competency “W eld Carbon Steel Pipes Using SMAW”

contains knowledge, skills and attitudes required for Shielded M etal Arc W elding
NC II. It is one of the specialized modules at National Certificates Level (NC II).
You are required to go through a series of learning activities in order to

complete each learning outcome of the module. In each learning outcome are
Information Sheets and Resources Sheets (Reference Materials for further reading
to help you better understand the required activities). Follow these
activities on your own and answer the self-check at the end of each learning
outcome. You may remove a blank answer sheet at the end of each module (or
get one from your facilitator/trainer) to write your answers for each self-check. If
you have questions, don’t hesitate to ask you facilitator for assistance.
Recognition of Prior Learning (RPL)
You may already have some or most of the knowledge and skills covered in this
learner’s guide because you have:
 been working for some time

 already completed training in this area
If you can demonstrate to your trainer that you are competent in a particular
skill or skills, talk to him/her about having them formally recognized so you
don’t have to do the same training again. If you have a qualification or
Certificate of Competency from previous trainings, show it to your trainer. If
the skills you acquired are still current and relevant to the unit/s of
competency they may become part of the evidence you can present for RPL. If
you are not sure about the currency of your skills, discuss this with your trainer.
At the end of this module is a Learner’s Diary. Use this diary to record
important dates, jobs undertaken and other workplace events that will assist
you in providing further details to your trainer or assessor. A Record of
Achievement is also provided for your trainer to complete once you complete the
module.
This module was prepared to help you achieve competency, in W elding Carbon
Steel Pipes Using SMAW. This will be the source of information for you to

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
acquire knowledge and skills in this particular trade independently and at
your own pace, with minimum supervision or help from your instructor.
 Talk to your trainer and agree on how you will both organize the Training
of this unit. Read through the module carefully. It is divided into
sections, which cover all the skills, and knowledge you need to
successfully complete this module.
QUALIFICATION: SHIELDED METAL ARC WELDING NC II
UNIT OF COMPETENCY: Weld Carbon Steel Pipes Using SMAW
MODULE TITLE: Welding Carbon Steel Pipes Using SMAW
INTRODUCTION: This module covers the knowledge, skills and

proper attitude in groove welding on carbon
steel pipes in performing root pass, clean root pass,
weld subsequent/ filling passes, and perform
capping.
NOM INAL DURATION: 80 HOURS
LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:

1. Perform root pass
2. Clean root pass
3. Weld subsequent/filling pass
4. Perform capping
ASSESSMENT CRITERIA:
1. Root pass is performed in accordance with WPS and/or

client specifications.
2. Task is performed in accordance with company or industry
requirement and safety procedure.
3. Weld is visually checked for defects and repaired, as
4. required
5. Weld is visually acceptable in accordance with applicable codes
and standards
6. Root pass is cleaned and free from defects and discontinuities
7. Task is performed in accordance with approved WPS
8. Subsequent/ filling passes is performed in accordance with approved WPS
QA Issued by:
SYSTEM
No.
Jerry R. Torrado
9. Weld is visually checked for defects and repaired, as required
and standards
11. Capping is performed in accordance with WPS and/or client specifications
12. Weld is visually checked for defects and repaired, as required
and standards
PRE-REQUISITE:
BASIC AND COMMON COMPETENCIES

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
LEARNING OUTCOME #1: Perform root pass
Learning Contents: 1. Essentials of welding
2. Safe welding practices
3. Weld defects, causes and remedies
4. Welding Procedure and Specifications (WPS)
5. International welding codes and standards
6. Acceptable weld profiles
7. Welding technique and procedures
ASSESSMENT CRITERIA:
1. Root pass is performed in accordance with WPS

and/or client specifications.
2. Task is performed in accordance with company
or industry requirement and safety procedure.
3. Weld is visually checked for defects and repaired,
as required
and standards
CONDITIONS:
Equipment
 AC-DC Welding Machine

 Welding Table
 Portable Grinder
 Portable Oven
 Welding Booth
Tools/Accessories
 Welding Mask
 Steel Brush
 Clear glass
 Chipping Hammer
 Dark glass
Supplies/Materials
 Electrodes
QA Issued by:
SYSTEM
No.
Jerry R. Torrado
 Carbon steel plates
 Cutting grinding disc
Personal Protective Equipment
 Safety shoes
 Apron
 apron
 Leggings
 Safety goggles
 Gloves
Training Manuals
 Arc welding manuals

 Welding procedures specifications
 Welding standards
ASSESSMENT METHODS:
 Observation and interview

 Demonstration and interview
 Written test
 Portfolio

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
LEARNING EXPERIENCES
Activities Special Instructions
1. Read Information Sheet 1.1 – 1 on the Read the information sheet

Essentials of welding . carefully
2. Answer Self – Check 1.1-1. Compare to answer key 1.1-1.
3. Read Information Sheet 1.1-2 on the Read the information sheet
Safe welding practices. carefully
4. Answer Self – Check 1.1-2. Compare to answer key 1.1-2.
5. Read Information Sheet 1.1-3 in Read the information sheet
identifying weld defe cts, causes and carefully
remedies
6. Answer Self – Check 1.1 -3. Compare to answer key 1.1-3.
7. Read Information Sheet 1.1 – 4 on Read the information sheet
Welding Procedures and Specifications carefully
(WPS).
8. Answer Self – Check 1.1 -4 (Written Compare to answer key 1.1-4.
Test)
9. Read Information Sheet 1.1-5 on Read the information sheet
International welding codes and standards. carefully
Test)
11. Read Information Sheet 1.1-6 on Read the information sheet
acceptable weld profiles. carefully
Test)
13. Guided by information sheet 1.1-7, Jot down observations.
observe the trainer as he demonstrates the
different welding techniques and
procedures correctly and properly.
14. Perform Job Sheets 1.1-7a-c on the Trainer evaluates performance
different welding techniques and and work outputs and makes
procedures. recommendations.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
INFORMATION SHEET No. 1.1-1
ESSENTIALS OF WELDING
After reading the Information Sheet, the trainee must be able to

determine the essentials of welding.
Weld quality and consistency can only be maintained with respect to the
five essentials. The five essentials of welding include the use of correct electrode
size, current, arc length or voltage, travel speed and electrode angles. All five
must be collectively and consistently maintain to successfully control the puddle
and produce a weld that is uniform in appearance, have consistent ripples,
smooth face contour, and no noticeable defect. Once the welder masters the
ability to consistently maintain the five essentials, the ability to control the
puddle will follow.
ELECTRODE SIZE
Choosing the correct electrode size involves many factors. If a smaller

recommended electrode is used, welding time and heat to the joint will increase.
It can result in increase costs, heat affected zone, cracking or distortion.
Larger electrode can cause melt – through and can be difficult to control in
out of position
joints. Poor appearance and possible defects can result. The welding procedure
designates the correct electrode size, generally based on metal type and
thickness. However, if no procedure or instruction is available the welder will
have to choose the correct electrode size.
CUR RENT
The correct current setting is vital for maintaining consistency in

weld quality. If the current is too high, the electrode melts too fast, and the
molten pool is larger and irregular. If the current is too high when welding single
vee -groove, it might blow holes through the joint and cause large molten metal
droplets to fall out of the groove.
If the current is too low, there is not enough heat to melt the base
metal. The molten pool will be too small, piles up, and looks irregular. Poor
penetration and incomplete fusion in the joint can result.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
TRAVEL SPEE D
Incorrect travel is a common mistake. Sometimes travel speed is the only

condition a welder may need to change. Travelling too fast causes the puddle to
freeze too quickly. Because of this, impurities and gases can become entrapped,
making the bead face narrow with pointing ripple. Incomplete penetration due to
loss of the keyhole in root pass is possible.
Travelling too slow will cause the puddle to be large, with pile – up, and a
straight ripple pattern. For out of position welding, slow travel sped can cause
the puddle to drip out the joint.
ELECTRODE ANGL E
One of the most essentials is the use of the correct electrode angles. For
fillet and groove welds, correct electrode angles are vital for pre venting
undercut and inadequate fill. When depositing a fillet weld the electrode should
be held so that it bisects the angle between the plates and is perpendicular to the
line of the weld. On groove weld, the technique is much the same; although
varying slightly with multiple pass welding.
There are two teams to specify electrode angles. These are travel angle and
work angles.
The travel angle applies to the position the electrode make with a reference
perpendicular to the axis of the weld in plane of the weld axis. It can be either
a drag angle or a push angle. A drag angle is when the electrode is
pointing backward, meaning the welder’s hand and electrode holder proceeds the
puddle. A push angle is when electrode is pointing just the opposite of the drag.
The work angle is the position the electrode makes with reference to the
surface of the plate on a plane perpendicular to the weld axis. On butt joints the
work angle is usually 90 degrees to the surface of the plate.
T o some degree, you can correct for an improper condition by varying the
essential variables. It is better though to have all conditions as correct as
possible.
AR C LENG TH
Arc length is very important for weld puddle control. Correct arc length
will cause the deposit to be neat of even ripple and of good penetration.
Too long arc length will cause the deposit to coarse rippled and flatter than
normal with an increase in spatter. When welding a root pass in an open root
vee groove, the keyhole can grow too large and loose of weld control can result.
Too short an arc will cause deposited to be narrow, uneven and irregular
rippled and with poor fusion. The arc length reduces the voltage and increases
the amperage slightly but the electrode may stick to the work. When welding root
passes, too short an arc length often results n loss of the keyhole.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
SELF – CHECK 1.1-1
(Essentials of W elding)
TRUE OR FALSE
Direction: Read each statement below carefully. Write TRUE if the statement
is correct and FALSE if the statement is not correct.
1. Using a larger electrode diameter can cause melt – through/ burn –
through.
2. Travelling too fast will make the bead face narrow with pointing ripple.
3. If the current is too low, the electrode melts too fast.
4. Quality or sound weld is the result of correct current, constant voltage,
travel speed, electrode angle and correct electrode size.
5. In fillet weld, electrode angle is not necessary for preventing
undercut and under fill.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
ANSWER KEY 1.1 – 1
Essentials of W elding
1. TRUE
2. TRUE
3. FALSE
4. TRUE
5. FALSE

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
INFORMATION SHEET NO. 1.1 -2
Welding Personal Protective Equipment (PPE)
After reading the Information Sheet, the trainee must be able to identify the
different personal protective equipment and their uses.
The hazards in arc welding can endanger a welder’s life if he/she is not
wearing the proper protective clothing and equipment. Here are some information
on the suitable outfit that a welder must wear while welding:
WELDING SHIELD/HELMET
Welding shield/helmet is used to protect the face and eyes from the arc
rays (Infrared Rays, Ultra Violet Rays) and heat and spatter from the molten
metal. The arc is viewed through a filter which reduces the intensity of radiation
but allows a safe amount of light to pass for viewing the weld pool and end of the
electrode.
The recommended minimum protective filter based on the welding current to
be used is shown in the table below:
Approximate Range
Of Welding Current Filter Lens Number
Up to 100 8
100 - 200 10
200 - 300 11
300 - 400 12
Over 400 13

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
LEATHER JACKET
Leather jacket is made of chrome leather and prevents the entry of sparks
between the welder’s clothes and body.
LEATHER APRON
Leather apron is made of chrome leather and provides a welder with

complete protection from sparks and hot metal from his/her chest to mid
calf.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
LEATHER GLOVES
Gloves are made of chrome leather and protect the welder’s hands from
heat, spatter, and radiation.
LEATHER SPATS
Spats are made of chrome leather and protect the feet from spatter.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
SAFETY GLASSES
Safety clear glasses are used to protect the eyes when chipping slag
and grinding.
WELDERS CAP
Welders cap is used to protect welder’s head from spatters in out of

position welding or in confined spaces.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
WELDERS LEATHER BOOTS
Welding Leather Boots is used to protect our feet from falling

spatter, sparks, and hot metals when welding overhead and confined spaces.
FACE SHIELD
Face Shield must also be worn where required to protect eyes. Welders
must wear safety glasses and chippers and grinders often use face shield in
addition to safety glasses.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
MULTIPLE CHOICE: Choose the correct answer and write the letter that
correspond to your choice on the answer sheet provided.
1. A safety gadget used to protect the face and eyes from the arc rays, heat
and spatter.
a. Welding gloves
b. Welding jacket
c. Safety shoes
d. Welding
helmet/shield
2. The most serious danger from exposure to welding arc

is, a. X – rays
b. Beta – rays
c. Ultra Violet Rays
d. Sun rays
3. Protect the entry of falling hot slag and

spatter. a. Leggings
b. Welding gloves
c. Welding helmet
d. Clear glass
4. When welding at a current setting of 120 amperes, what is the

recommended filter lens number?
a. 8
b. 12
c. 10
d. 11
5. Safety gadget used to protect the eyes when chipping slag and
grinding. a. Safety glasses
b. Leather spats
c. Leggings
d. Welding gloves

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
1. d
2. c
3. a
4. c
5. a

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
INFORMATION SHEET 1.1 -3
Identifying W eld Defects, Causes and Remedies
After reading the Information Sheet, the trainee must be able to:
1. Identify the different welding defects and causes; and
2. Know the causes and remedies for these defects.
As previously explained, weld quality can only be attained by following

the five essentials, as preconditions for welding. Without due regard to
these essentials, defects will occur. The most common defects and corresponding
causes and preventions are discussed below.
A. P OR OS ITY
CAUSES:
1. Short arc with exception of low hydrogen

2. Insufficient paddling
3. Impaired base metal
4. Poor Electrode
5. Improper Shield Coverage
REMEDIES:
1. Check Impurities in base metal

2. Allow sufficient paddling
3. Use proper current
B .POOR PENE TR ATION
CAUSES:
1. Speed too fast

2. Electrode too large
3. Current too low
4. Faulty penetration

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
REMEDIES:
1. Use enough current to obtain desired penetration- weld slowly

2. Select electrodes according to welding groove size
3. Leave proper gap at bottom of weld
C.W ARP ING
CAUSES:
1. Shrinkage of weld metal

2. Faulty clamping of parts
3. Faulty preparation
4. Over heating at joint
REMEDIES:
1. Peen joint edges before welding

2. Weld more rapidly
3. Avoid excessive space between parts
4. Pre-form parts before welding
5. Use proper sequence
6. Clamp or tack parts properly – back up to cool
7. Adopt a proper welding procedure
8. Use high speed, moderate penetration process
D.UNDERCUTING
CAUSES:
1. Faulty Electrode or poor manipulation

2. Faulty Electrode use
3. Correct to high
REMEDIES;
1. Use a uniform weave in butt welding

2. Avoid using an overly large electrode
3. Avoid excessive weaving
4. Use moderate current weld slowly

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
E . C R A C K W E L DS
CAUSES:
1. Wrong electrode
2. Weld and parts sizes unbalanced
3. Faulty welds
5. Rigid joint
REMEDIES:
1. Design structure to eliminate rigid joints

2 Heat parts before welding
3. Avoid welds in string beads
4. Keep ends free to move as long as possible
5. Make sound welds of good fusion
6 Adjust weld size to parts size
7. Allow joints a proper and uniform gap
8 Work with amperage as low as possible
F.P OOR APP EARANCE
CAUSES:
1. Faulty electrode
2. over hang
3. Improper use of electrode
4. Wrong arc voltage and current
REMEDIES:
1. Use a proper welding technique

2. Avoid over heating
3. Use a uniform weave
4. Avoid overly high current

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
G .P OOR FUS ION
Lack of fusion, also called cold lapping or cold shuts
CAUSES:
1. Wrong speed
2. Current improperly adjusted
4. Improper electrode size
REMEDIES:
1. Adjust electrode to match joint

2. Weave must be sufficient to melt sides of joint
3. Select proper current and voltage
4. Keep weld metal from flowing away from plates
H. S P ATTER
CAUSES:
1. Arc blow
2. Current too high
3. Arc too long
4. Faulty electrode
REMEDIES:
1. Clean parts in weld area

2. Adjust current
3. Adjust voltage
4. Pick suitable electrode

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
MULTIPLE CHOICE: Choose the correct answer and write the letter that
correspond to your choice on the answer sheet provided.
1. When electrode coating absorbs moisture, what will be the effect to the
weld bead?
a. poor penetration
b. porosities
c. excessive
penetration d. undercut
2. Incomplete sidewall fusion is normally found

between a. weld and base metal
b. HAZ and base metal
c. root joint
d. cover pass and filling pass
3. Welding distortion, warp and stresses are cause

by a. weaving technique
b. intermittent welding
c. high temperature
heat d. backstop welding
4. The most common cause of undercut in a weld is

too a. low a current
b. high an arc
c. short an arc
d. high a current
5. Which of the following weld defects DOES NOT have any tolerance
for acceptance?
a. crack
b. porosity
c. slag inclusion
d. undercut

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
ANSWER KEY 1.1 –3
1. b
2. a
3. c
4. d
5. a

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
INFORMATION SHEET 1.1 -4
Welding Procedure Specification (WPS)
1. Identify welding procedure specification:
2. Interpret welding procedures specification.
A W elding Procedure Specification (WPS) is a formal document describing

we ldin g procedures. The purpose of the document is to guide welders to the
accepted procedures so that repeatable and trusted welding techniques are
used. A WPS is developed for each material alloy and for each welding type used.
Specific codes and/or engineering societies are often the driving force behind the
development of a company's WPS. A WPS is supported by a Procedure
Qualification Record (PQR or WPQR). A PQR is a record of a test weld performed
and tested (more rigorously) to ensure that the procedure will produce a
good weld. Individual welders are certified with a qualification test documented in
a Welder Qualification Test Record (WQTR) that shows they have the
understanding and demonstrated ability to work within the specified WPS.
The following are definitions for WPS and PQR found in various codes and
standards:
According to the Ame rican We ldin g Socie ty (AWS), a WPS provides in detail
the required welding variables for specific application to assure re pe atability by
properly trained we lde rs. The AWS defines welding PQR as a record of welding
variables used to produce an acceptable test weldment and the results of tests
conducted on the weldment to qualify a Welding Procedure Specification.
The Ame rican Socie ty of Me chanical En gin ee rs (ASME) similarly defines a

WPS as a written document that provides direction to the welder or
welding operator for making production welds in accordance with Code
requirements. ASME also defines welding PQR as a record of variables
recorded during the welding of the test coupon. The record also contains the
test results of the tested specimens.
In Europe, the Europe an Committee for Stan dardization (CEN) has adopted
the ISO standards on welding procedure qualification (ISO 15607 to ISO 15614)
and on welder qualification (ISO 9606), with the exception of qualification for
steel welders, where a new version of the old European EN 287-1 standard still
applies. EN ISO 15706 defines a WPS as "A document that has been qualified by
one of the methods described in clause 6 and provides the re quired variables of
the welding procedure to ensure repeatability during production welding". The
same standard
QA Issued by:
SYSTEM
No.
Jerry R. Torrado
defines a Welding Procedure Qualification Record (WPQR) as "Record comprising
all necessary data needed for qualification of a preliminary welding procedure
specification ".In addition to the standard WPS qualification procedure specified
in ISO 15614, the ISO 156xx series of standards provides also for
alternative WPS approval methods. These include: Tested welding consumables
(ISO 15610), Previous welding experience (ISO 15611), Standard welding
procedure (ISO 15612) and Preproduction welding test (ISO 15613).
In the oil and gas pipeline sector, the American Petroleum Institute API
1104 standard is used almost exclusively worldwide. API 1104 acce pts the
definitions of the American Welding Society code AWS A3.
Welding Procedure Specification:- (Example FORM )

Weld Procedure Number 30 P1 TIG 01 Issue A
Qualifying Welding Procedure (WPAR) WP T17/A
Method Of
Machine and
Preparation
Degrease
Manufacturer: National Fabs Ltd and Cleaning:
25 Lane End Grade 304L
Parent Metal
Birkenshaw Specification: Stainless Steel
Leeds
Parent Metal 3 to 8mm Wall
Thickness
Location: Workshop
Pipe Outside
Welding 25 to 100mm
Manual TIG Diameter
Process:
Welding Position: All Positions
Joint Type: Single Sided Butt
Weld Welding Upwards
Progression:
Joint Design Welding Sequences

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Welding Consumables:-
Size Of Drying: Gas Flux: -
Run
Type, Designation TradeCurrent Vol
Process Filler Gas Flow Rate - Backing:
TIG 1.6mm A V
Name: Any Special
Subs MetalBaking
140or Shield: Tungsten
1 TIG 1.2mm 70 - 90
2 And 80 - N/
Electrode Type/ Size: Details of WireProduction
Back Gouging/Backing: Preheat tage Type Of Travel Heat
Fee
BS 2901 Part 2 : 308S92 dSequence
Temperature: Current/Polarity Speed Input
No Speed
Interpass temperature: Post Argon 99.99% Purity 1. Clean weld
Weld Heat Treatment Time, 8 - DC-
12 LPM
A N/A and N/A25mmN/A
temperature, method: 5 LPMDC- borders to
Heating and Cooling 2% Thoriated 2.4mm Dia. bright metal
Rates*: Gas Backing using
5°C Min approved
200°C Max solvent.
Not Required
2. Position
items to be
welded
ensuring
good fit up
and apply
purge
3. Tack weld
parts
together
using TIG,
tacks to at
least 5mm
min length
4. Deposit root
run using
1.2mm dia.
wire.
5. Inspect root
run
internally
6. Complete
weld using
1.6mm dia.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
wire using
stringer
beads as
required.
7. 100% Visual
inspection of
completed
weld

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
SELF – CHECK 1.1 – 4
Welding Procedure Specification (WPS)
Test I – IDENTIFY THE FOLLOWING:
1. ASME
2. AWS
3. API 1104
4. ISO 15612
5. ISO 15613
Test II – ESSAY (5pts.)
1. W hat is WPS?

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
ANSWER KEY 1.1 -4
Welding Procedure Specifications
Test I:
1. Welding Procedure Specification
2. American Welding Society
3. American Petroleum Institute 1104 - oil and gas pipeline sector
4. Tested welding consumables
5. Standard welding procedure
Test II
1. A Welding Procedure Spec if ica tion (WPS) is a formal document describing
welding procedures. The purpose of the document is to guide welders to the
accepted procedures so that repeatable and trusted welding techniques are
used.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Information Sheet No. 1.1-5
International W elding Codes and Standard
1. Identify international welding codes and standards; and

2. Interpret/apply international welding codes and standards.
Welder Qualifications
This information sheet is designed to give you a broad overview of

the specifications, codes and standards that are widely used in welded
fabrication, construction and maintenance work.
The begins with definition of codes, standards, specifications and related

terms. Another section deals with the advantages associated with the
standardization. In addition, the module identifies various agencies and societies
that sets codes and standards. The module then moves on to the
identification and study of specifications, codes and standards that govern
welding in relation to:
structural steel,
boilers and pressure vessels,
piping systems,
pipelines and transmission system and
storage tanks
Before a welder can begin working on any job covered by a welding code or
specification be must become a certified under the code that applies.
Many different codes are in use today and it is exceeding important that the
specific code is referred to when taking qualifications test. In general the
following type of work is covered by codes pressure piping, high way and rail
ways bridges, public buildings tanks and containers that will hold flammable or
explosive, materials cross country pipe line aircraft ordinance.
Certification is obtained differently under the various codes

certification under one code will not necessarily qualify a welder under a
different code. In most cases certification for one employer will not allow the
welder to work for another employer .Also the welder uses a different process
or if the procedure
QA Issued by:
SYSTEM
No.
Jerry R. Torrado
adhere drastically re- certification is not required providing the work performed
meets the quality requirement. An exception is the air craft code which
requires re-qualification every six months.
Qualification test may be begin by responsible manufacturers or

contractors. On pressure vessel work the welding procedure must also be
qualified and this must be done before the welders can be qualified. Under these
codes, this is not necessary. To become qualified and the welder must make
specified welds using the required process, base metal ,thickness, electrode,
type position and joint design .Test specimen must be made according to
standardize size sand under observation of a qualified person .In most cases
government specifications a inspector must witness the making of welding
specimen must be properly identified prepared for testing. The most common
test is the guided bead test, however in some cases x-ray examinations,
fracture test or in order test are employed satisfactory completion of test
specimen and providing that they meet acceptability standards will qualify the
welder for specific for the specific types of welding. The welding that will be
allowed again depends on the particular code. In general however the range of
thickness may be welded less difficult positions may be employed and steels of
fewer alloys are usually included.
Qualifications of welder is an extremely technical subject and cannot be

covered .It is recommended that the code be obtained and studied prior to taking
any test.
Terms Used In This Section:
Codes – documents that govern and guide welding and other activities.
Codes generally use the word shall to indicate the mandatory use
of certain types of materials, methods and procedures.
Standards – Documents that govern and guide welding and other
activities. Standards generally describe the requirements for
materials, process, products, systems or services rendered. Standards
often specify the procedures, methods, equipments and tests th
at determine if standards requirements have been met. Standards
can be in the form of codes, specifications, classifications and guides.
Specifications – Are similar to codes excepts that specifications mainly
provide requirements for products rather than processes.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Purpose:
The purpose of Codes, Standards and specifications is to secure that

safe and reliable products are produced and that those persons working around
welded structures and equipment are not exposed to undue danger or hazard to
their health.
Welding Specifications:
 G – GROOVE
 F – FILLET
PLATE
1 – FLAT POSITION
2 – HORIZONTAL POSITION
3 – VERTICAL POSTION
4 – OVER – HEAD POSITION
PIPE
1 – MOVABLE PIPE POSITION

2 – FIXED / MOVABLE VERTICAL PIPE POSITION
5 – FIXED HORIZONTAL PIPE POSITION
6 – FIXED 45 DEGREE PIPE POSITION
1. 2G – MEANS PIPE GROOVE, FIXED / MOVABLE VERTICAL PIPE POSITION
2. 5G - MEANS PIPE GROOVE, FIXED HORIZONTAL PIPE POSITION
3. 6G - MEANS PIPE GROOVE FIXED 45 DEGREE PIPE POSITION

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
International W elding Codes and Standard
MATCHING TYPE: Match column A to column B. Write only the letter on

your answer sheet.
Column A Column B
1. Means Pipe Groove, A. 1F Plate
Fixed Horizontal Pipe Position
B. 6G Pipe
2. Groove Weld Horizontal
Position Plate C. 2G Pipe
3. Movable Pipe Position D. 1G Pipe
4. Means Pipe Groove, Fixed E. 4G Plate

/ Movable Vertical Pipe Position
F. 2G Plate
5. Means Pipe Groove Fixed 45
Degree Pipe Position G. 5G Pipe
6. Groove Weld Over – Head

Position Plate
7. Fillet Weld Flat Position Plate

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
International welding codes and standards
1. G
2. F
3. D
4. C
5. B
6. E
7. A

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Information Sheet no. 1.1 – 6
Weld Profiles
After reading the Information Sheet and viewing of Good and Bad welds
indicators video, the trainee must be able to:
1. Different W eld P rofiles; and

3. Identify Good and Bad W elds.
Different W eld Profiles
A B C
A) Amperage correct (GOOD)

B) Amperage too low (BAD)
C) Amperage too high (BAD)

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Indicators of Good W eld Indicators of Bad W eld
1. Proper Current/ voltage/speed 1. Welding Current too high
2. Nice Convex 2. Arc too long/ voltage high
3. Straight line/ edge 3. Excessive filling up of weld
4. Smooth weld bead metal
5. Uniform weave/Ripples 4. over lapping bead
6. An efficient Weld 5. Bead very irregular
7. Excellent Weld 6. Irregular deposit
8. No Defects 7. Weld not properly
9. Good Penetration 8. Welding speed too fast
10. No Spatter 9. Welding speed too slow
10. Poor Penetration
11. Poor weld Appearance
12. No bead
13. War page metal
14. Distortion of metal
15. Warping of metal
16. Crack Welds
17. Weld Streets
18. Shrinkage metal
19. Poor internal fusion weld
20. Brittle Welds
21. Magnetic Blow
22. Pinholes
23. Cold laps
24. Concavity

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Weld Profiles
MATCHING TYPE: Match indicators in column A to its results in column

B. Write only the letter on your answer sheet.
Column A Column B
1. Voltage High A. Wet Electrode
B. Arc Length Too Long

2. High Current
C. Spatter
3. Arc Strike D. Low Current
4. Slag Inclusion E. Failure To Clean The

Weld
5. Porosity F. Improper Starting Of Arc
G. Undercut
6. Arc Blow
7. Poor Penetration

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Weld Profiles
1. B
2. G
3. F
4. E
5. A
6. C
7. D

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Job Sheet No. 1.1.7a
Welding Technique and Procedure
Title: Perform Root Pass
Performance Objectives: Perform root pass in a multiple pass groove

weld in Flat position (1G)
Suppli es and M aterials: 2 pcs. Flat bar 10mmx60mmx150mm MS

2 pcs. W elding Electrode E6011/E6010 #3.2mm
Tools and Equipment: W elding M achine w/ complete accessories

Automatic cutting machine
Chipping hammer
Steel brush
W elding gloves W
elding jacket W elding
helmet
Steps:
1. Proceed to the Workstation at the SMAW Practical Work Area
2. Prepare the edge of the two(2) plates, with a bevel angle of 30
degrees and 2mm root face.
3. Wear suitable protective clothing to avoid burns and radiation
4. Set the welding machine;
Current setting:3.2mm, E6013: 90 – 120 amperes
5. Put the plates on the welding table in flat position and make sure that
the root gap is 3.2mm.
6. Position the plates;
Clamp the plates in the positioner in a flat position.
7. Position yourself comfortably with the electrode grip to the holder.
8. Strike the arc and hold the electrode at 90 degrees work angle and
75 – 80 degrees travel.
9. Maintain a short arc.
10. Move the electrode using a whipping motion and maintain a keyhole
Until you reach the other end of the plates.
11.Clean and check your work based on the Performance Criteria
Checklist.
12. After doing the task, present your work to your Trainer for evaluation.
Assessment M ethod:
Performance Test and Evaluation of finished output

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Performance Criteria Checklist
Job Sheet 1.1-7
Welding Technique and Procedure
Trainees Name Date:
CRITERIA YES NO
Root pass is performed in accordance with WPS and/or
client specifications or as specified by welding codes and
standards on:
 concavity
 convexity
 undercut
 excess penetration
 lack of fusion
 cracks
 burn – through
Task is performed using PPE
Weld is visually checked for def ects and repaired, as
required
Weld is visually acceptable in accordance with applicable
codes and standards
JERRY R. TORRADO, Trainer Date

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
Terms and Definitions
1) base metal – the metal that is to be worked or welded

2)weld bead – a deposit of filler metal from a single welding pass
3)weld defect– an irregularity that spoils the weld appearance or
impairs the effectiveness of the weld or weldment
by causing weakness or failure
4) weld line – the junction of weld metal and the base metal, or
the junction of base metal parts when filler metal is not used
5) weldment – an assembly or structure whose component parts are joined
by welding
6) welding – joining two metals by applying heat to melt and fuse
them, with or without filler metal
7) welding electrode – the current-carrying rod used to strike an arc
between rod and metal
8) welding rod – filler metal in the form of a rod or heavy wire
9) welding torch –a gas mixing and burning tool for the welding of metal
10) undercut – is a groove at the toe ( or at the root) of a weld run due on welding.
11) slag inclusion – these are caused by slag trapped in the weld metal.
12) incomplete penetration – failure of weldment to extend into the root of the
joint
to provide full throat depth.
13) porosity – is entrapped gas cavities formed during solidification of the weld
14) cracks – are fractured that displace an opening or a split in the weld or
base metal.
15) Codes – documents that govern and guide welding and other activities.
Codes generally use the word shall to indicate the mandatory
use of certain types of materials, methods and procedures.
16) Standards – Documents that govern and guide welding and other
activities. Standards generally describe the requirements
for materials, process, products, systems or services
rendered.
17) Specifications – Are similar to codes excepts that specifications mainly
provide requirements for products rather than processes.
18) W elding P rocedure Specification (WPS) - is a formal document
describing we lding procedures. The purpose of the document is
to guide welders to the accepted procedures so that repeatable
and trusted welding techniques are used.
19) welding helmet – is used to protect the face and eyes from the arc rays, heat
and
spatter.
20) welding gloves – are made of chrome leather to protect welder’s hands from
heat
spatter and radiation.

QA Issued by:
SYSTEM
No.
Jerry R. Torrado
QA Issued by:
SYSTEM
No.
Jerry R. Torrado

Competency - Based Learning Materials: Metals and Engineering (Sector)

Uploaded by

Copyright:

Available Formats

Competency - Based Learning Materials: Metals and Engineering (Sector)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Competency - Based Learning Materials: Metals and Engineering (Sector)

Uploaded by

Copyright:

Available Formats

COMPETENCY - BASED LEARNING MATERIALS

METALS AND ENGINEERING

LMMSAT - Shielded M etal Date Developed: Document N.

No. Unit of Competency Module Title Code

LMMSAT - Shielded M etal Date Developed: Document N.

The unit of competency “W eld Carbon Steel Pipes Using SMAW”

You are required to go through a series of learning activities in order to

Recognition of Prior Learning (RPL)

 been working for some time

LMMSAT - Shielded M etal Date Developed: Document N.

QUALIFICATION: SHIELDED METAL ARC WELDING NC II

UNIT OF COMPETENCY: Weld Carbon Steel Pipes Using SMAW

MODULE TITLE: Welding Carbon Steel Pipes Using SMAW

INTRODUCTION: This module covers the knowledge, skills and

NOM INAL DURATION: 80 HOURS

Upon completion of this module, the trainee/student must be able to:

1. Root pass is performed in accordance with WPS and/or

BASIC AND COMMON COMPETENCIES

LMMSAT - Shielded M etal Date Developed: Document N.

1. Root pass is performed in accordance with WPS

 AC-DC Welding Machine

Personal Protective Equipment

 Arc welding manuals

 Observation and interview

LMMSAT - Shielded M etal Date Developed: Document N.

Activities Special Instructions

1. Read Information Sheet 1.1 – 1 on the Read the information sheet

LMMSAT - Shielded M etal Date Developed: Document N.

After reading the Information Sheet, the trainee must be able to

Choosing the correct electrode size involves many factors. If a smaller

The correct current setting is vital for maintaining consistency in

LMMSAT - Shielded M etal Date Developed: Document N.

Incorrect travel is a common mistake. Sometimes travel speed is the only

LMMSAT - Shielded M etal Date Developed: Document N.

1. Using a larger electrode diameter can cause melt – through/ burn –

3. If the current is too low, the electrode melts too fast.

4. Quality or sound weld is the result of correct current, constant voltage,

travel speed, electrode angle and correct electrode size.

5. In fillet weld, electrode angle is not necessary for preventing

undercut and under fill.

LMMSAT - Shielded M etal Date Developed: Document N.

LMMSAT - Shielded M etal Date Developed: Document N.

Welding Personal Protective Equipment (PPE)

LMMSAT - Shielded M etal Date Developed: Document N.

Leather apron is made of chrome leather and provides a welder with

LMMSAT - Shielded M etal Date Developed: Document N.

LMMSAT - Shielded M etal Date Developed: Document N.

Welders cap is used to protect welder’s head from spatters in out of

LMMSAT - Shielded M etal Date Developed: Document N.

Welding Leather Boots is used to protect our feet from falling

LMMSAT - Shielded M etal Date Developed: Document N.

2. The most serious danger from exposure to welding arc

3. Protect the entry of falling hot slag and

4. When welding at a current setting of 120 amperes, what is the

LMMSAT - Shielded M etal Date Developed: Document N.

Welding Personal Protective Equipment (PPE)

LMMSAT - Shielded M etal Date Developed: Document N.

Identifying W eld Defects, Causes and Remedies

As previously explained, weld quality can only be attained by following