Installation and Maintenance Manual

Forbes Marshall Safety Relief Valve

FMSRV (DN20-50)

Energy Conservation | Environment | Process Efficiency www.forbesmarshall.com

Table of Contents

1. Preface .................................................................................1

2. Important Safety Notes .......................................................1

3. Brief Product Information .....................................................3

4. Product Working Principle ...................................................6

5. Installation Guidelines .........................................................6

6. Commissioning Guidelines ...................................................8

7. Maintenance Guidelines ......................................................9

8. Troubleshooting....................................................................11

9. Available Spares ..................................................................12

10. Warranty Period .................................................................13

PLEASE NOTE - Throughout this manual this cautionary symbol is used to

describe a potential damage or injury that might occur if the safety
considerations are overlooked. This symbol denotes CAUTION, WARNING or
DANGER.

Forbes Marshall Safety Relief Valve

1. Preface:
This manual is intended for anyone using, commissioning, servicing, or disposing the below
mentioned products safely and efficiently.
Forbes Marshall Safety Relief Valve[ FMSRV (DN20-50)]
Sizes: DN20 (3/4”), DN25 (1”), DN40 (1 ½”), DN50 (2”)
PLEASE NOTE:
Throughout this manual the following cautionary symbol is used to describe a potential damage
or injury that might occur if the safety considerations are overlooked.
2. Important Safety Notes:
Read this section carefully before installing/operating/maintaining the product. The
precautions listed in this manual are provided for personnel and equipment safety.
Furthermore, Forbes Marshall accepts no responsibility for accidents or damage
occurring as a result of failure to observe these precautions. Note that the product is
designed to perform for non-contaminated fluids only. A contamination in the form of
chemical, foreign particle etc. can lead to problem with product performance and life of
the product.
If these products in compliance with the operating instructions are, properly installed,
commissioned, maintained and installed by qualified personnel (refer Section 2.7) the safety
operations of these products can be guaranteed. General instructions for proper use of tools and
safety of equipments, pipeline and plant construction must also be complied with.
2.1 Intended use:
Check if the product is suitable for intended use/ application by referring to the installation
and maintenance instructions, name plates and technical information sheets.
i) The product is suitable for use as defined in the technical information sheet. In case the
need arises to use the product on any other fluid please contact Forbes Marshall for
assistance.
ii) Check for the suitability in conformance to the limiting conditions specified in technical
information sheet of the product.
iii) The correct installation and direction of fluid flow has to be determined.
iv) Forbes Marshall products are not intended to resist external stresses, hence necessary
precautions to be taken to minimize the same.
2.2 Accessibility and Lighting:
Safe accessibility and working conditions are to be ensured prior to working on the product.
2.3 Hazardous environment and media:
The product has to be protected from hazardous environment and check to ensure that no
hazardous liquids or gases pass through the product.

FMSRV (DN20-50) 1
 2.4 Depressurizing of systems and normalizing of temperature:
Ensure isolation and safety venting of any pressure to the atmospheric pressure. Even if the
pressure gauge indicates zero, do not make an assumption that the system has been
depressurized.
To avoid danger of burns allow temperature to normalize after isolation.
2.5 Tools and consumables:
Ensure you have appropriate tools and / or consumables available before starting the work.
Use of original Forbes Marshall replacement parts is recommended.
2.6 Protective clothing:
Consider for the requirement of any protective clothing for you/ or others in the vicinity for
protection against hazards of temperature (high or low), chemicals, radiation, dangers to
eyes and face, noise and falling objects.
2.7 Permits to work:
All work to be carried out under supervision of a competent person. Training should be
imparted to operating personnel on correct usage of product as per Installation and
Maintenance instruction. “Permit to work” to be complied with (wherever applicable), in
case of absence of this system a responsible person should have complete information and
knowledge on what work is going on and where required, arrange to have an assistant with
his primary goal and responsibility being safety. “Warning Notices” should be posted
wherever necessary.
2.8 Handling:
There is a risk of injury if heavy products are handled manually. Analyze the risk and use
appropriate handling method by taking into consideration the task, individual, the working
environment and the load.
2.9 Freezing:
Provision should be made to protect systems which are not self-draining, against frost
damage (in environment where they may be exposed to temperatures below freezing point)
to be made.
2.10 Product Disposal:
It is necessary to dispose this product only in accordance with local regulations at the
authorized, qualified collecting point specified for equipment’s and its parts—Please refer
the part details mentioned in the material table of this manual. Please follow all waste
disposal guidelines (Management & Handling) as published by local governing authorities in
India & abroad
2.11 Returning products:
Customers and Stockist are reminded that, when returning products to Forbes Marshall they
must provide information on any hazards and the precautions to be taken due to
contamination residues or mechanical damage which may present a health, safety or
environmental risk.
This information must be provided in writing including Health and Safety data sheets
relating to any substances identified as hazardous or potentially hazardous.

2 Forbes Marshall Safety Relief Valve

3. Brief Product Information:

3.1 Description:
The Forbes Marshall Safety Relief Valve FMSRV is a high lift safety relief valve with gun
metal seat, valve and brass internals suitable for use on steam, air and water.
3.2 Size and Pipe Connections:
DN 20, 25, 40 and 50
Screwed BSPT/BSP/NPT
Available with IBR certificate
3.3 Limiting Conditions:

PMO maximum operating pressure 17.5 bar g

TMO maximum operating temperature 224°C
Cold hydraulic test pressure 35 bar g
For following set pressure ranges 6 colour coded springs are available

05 to 15 psi White
15 to 35 psi Yellow
35 to 75 psi Green
75 to 125 psi Blue
125 to 175 psi Red
175 to 250 psi Black

3.4 Operating Range:

The product must not be used in this region.

FMSRV (DN20-50) 3
 Figure 1: Forbes Marshall Safety Relieve Valve
Materials:
No Part Material
1 Seat Gun metal
2 Seat ring Gun metal
3 Valve Gun metal
4 Spindle lock nut Brass
5 Bonnet IS 210 Gr. FG260
6 Spindle Brass
7 Spring Stainless steel
8 Bottom spring guide C 20
9 Top spring guide C 20
10 Adj. locking nut Brass
11 Adj. bolt Brass
12 Cap C20
13 Lever Aluminium
14 Lever fulcrum pin C20
15 Seat ring locking screw and nut (not shown) Brass
Dimensions: (approx. ) in mm (Refer to Figure 1)

Size DN A B C
20 48 60 145
25 60 65 160
40 73 84 205
50 80 108 250

4 Forbes Marshall Safety Relief Valve

3.5 Capacity Chart:

STEAM
4600
4400
4200
DN50
4000
3800
3600
3400
3200
3000
2800
2600
DN40
kg/hr

2400
2200
2000
1800
1600
1400
1200
DN25
1000
800
DN20
600
400
200
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Set Pressure in bar g

WATER
80000

DN50
70000

60000

50000
Litres/hr

40000
DN40
30000

20000
DN25

DN20
10000

0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Set Pressure bar g

AIR
1600
1550
1500
1450
DN50
1400
1350
1300
1250
1200
1150
1100
1050
1000
950
dm3/sec

900 DN40
850
800
750
700
650
600
550
500 DN25
450
400
350
300 DN20
250
200
150
100
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Set Pressure in bar g

FMSRV (DN20-50) 5
4. Product Working Principle : (Refer to Figure 1 )
The Forbes Marshall safety relief valve is normally set at a pressure which is 10% above the
working pressure of the system. This is referred to as a set pressure. When the safety pressure
reaches blow off pressure the safety relief valve opens to its full lift to discharge full capacity. The
valve closes at reset pressure.
The steam enters the safety relief valve through the inlet from the bottom. When the steam
reaches the set point, it lifts the valve (3) off the seat (1), working against the spring (7) present
inside the valve body. (The set pressure can be changed using the adjustment bolts (11)). As long
as the steam pressure exceeds the set pressure, the valve remains open. As soon as it comes below
the set pressure, the spring force pushes the valve (3) back onto the seat (1).
The seat ring (10) guides the valve (3) back to the seat (1).
5. Installation Guidelines:
Note: Before implementing any installations observe the 'Important Safety notes” in
section 2. Referring to the Installation and Maintenance Instructions, name-plate and
Technical Information Sheet, check that the product is suitable for the intended
installation.
1. The valve should always be mounted vertically upwards with its main axis kept vertical.
2. There should be no intervening valve or any fitting between the piping and the safety relief
valve which could isolate the FMSRV (Refer to 2a).
3. The inlet connection should never be smaller than the valve inlet and output pipe should be
either equal or larger than the valve outlet.
4. Where the outlet pipework is directed upwards a small bore drain should be provided at the
lowest point. Take the drain to a place where discharge will not create any hazard or
inconvenience (Refer to 2b).
5. Each safety relief valve should have its own discharge pipe.
6. Make sure that safety relief valve is set to the correct pressure.
7. safety relief valves should not be insulated.
8. Excessive pressure loss at the inlet of a safety relief valve when it operates will cause
extremely rapid opening and closing of the valve, observed as chattering or hammering. This
may result in reduced capacity as well as damage to seating faces and the other parts of the
valve. When normal pressure is restored it is possible that the valve will leak. Therefore the
Valve should be fitted 8-10 pipe diameters downstream of Converging or Diverging Fittings
or Bends (Refer to 2c)

6 Forbes Marshall Safety Relief Valve

These valves are not suitable for mounting on boilers

2a 2b

8-10 Pipe Diameters downstream of

converging ‘Y’ fittings or bends.
- 2c -

Figure 2: Correct Installation of Forbes Marshall Safety Relief Valve

FMSRV (DN20-50) 7
6. Startup and Commissioning :
6.1 Flushing of lines:
As part of pre-installation all fluid handling equipment particularly piping should be
thoroughly cleaned of scale and the internal debris which accumulates during construction.
This is accomplished by blowing or flushing with air, steam, water and other suitable
medium.
Note: For a detailed procedure on flushing of lines please visit Forbes Marshall website.
6.2 Safety relief valve setting : (Refer to Figure 1)
1. The safety relief valve should be set at a pressure, which is 10% above the working
pressure of the system.
2. Forbes Marshall safety relief valve, FMSRV (DN20-50) comes with 6 color-coded springs
w.r.t. set pressure ranges
White - 05 to 15 psi Yellow – 15 to 35 psi
Green – 35 to 75 psi Blue 75 to 125 psi
Red – 125 to 175 psi Black 175 – 250 psi
The range is marked on the safety relief valve cover body; safety relief valve can be set in
this range.
3. To set the safety relief valve, please remove the cir clip, pin, lever (13) and cap.
4. Before setting of safety relief valve, please ensure that the safety relief valve discharge is
routed at safe location.
5. Charge the steam line and ensure that the steam pressure is 10% more than the system
operating pressure and test the safety relief vale by shutting down the downstream
stop valve without the chance of downstream process being over pressurized.
6. If safety relief valve is not blowing at that pressure, then loosen the adjustment lock nut
(10) and do the set pressure adjustment with adjustment bolt (11). By rotating
adjustment bolt in clockwise direction, set pressure increases and it decreases by
rotating it in anticlockwise direction.
7. After setting the required set pressure, hold the adjustment bolt and tighten the
adjustment lock nut (10).

8 Forbes Marshall Safety Relief Valve

7. Maintenance Guidelines :
Before undertaking any maintenance on the product it must be isolated from both
supply line and return line and any pressure should be allowed to safely normalize to
atmosphere. The product should then be allowed to cool.
7.1 Routine and Preventive Maintenance:

Frequency for checking and maintaining

Parameters to be
S.No
checked Half
Immediately Daily Weekly Monthly Quarterly Annually
yearly
Visual inspection for
1 Y
leakages
Testing of safety relief
2 Y
valve

3 Cleaning of internals Y

*Re-certification by respective regulatory authorities as and when required.

7.2 Tool Kit:
To carry out any maintenance of the FMSRV use the tools mentioned in the table below.
Part Tool Size
For DN20
Spindle lock nut Open Spanner 24 mm (A/F)
Valve seat Open Spanner 36/38 mm (A/F)
Adjustment bolt and lock nut Open Spanner 16/17mm (A/F)
Blowdown ring lock nut Open Spanner 8mm (A/F)
For DN25
Spindle lock nut Open Spanner 24mm (A/F)
Valve seat Open Spanner 48 mm (A/F)
Adjust bolt and lock nut Open Spanner 21mm (A/F)
Blowdown ring lock nut Open Spanner 8mm (A/F)
For DN40
Spindle lock nut Open Spanner 30 mm (A/F)
Valve seat Open Spanner 58mm (A/F)
Adjust bolt and lock nut Open Spanner 26mm (A/F)
Blowdown ring lock nut Open Spanner 8mm (A/F)
For DN50
Spindle lock nut Open Spanner 30 mm (A/F)
Valve seat Open Spanner 71 mm (A/F)
Adjust bolt and lock nut Open Spanner 30 mm (A/F)
Blowdown ring lock nut Open Spanner 8mm (A/F)

FMSRV (DN20-50) 9
 7.3 Maintenance/Replacement Procedure : (Refer to Figure 1)
1. Before carrying out any maintenance on the valve, make sure that the system is isolated
and depressurized.
2. Unscrew the whole safety release valve from the pipeline.
3. Remove the pin to release the easing lever (13).
4. Remove the top cover.
5. Loosen the adjustment bolt locknut.
6. Rotate the adjustment bolt (11) anti clockwise to ease the spring tension inside the
body.
Note: It is very important to ease off the spring tension before carrying out any further
maintenance.
7. Clamp the Hexagonal valve seat to the vice.
8. Unscrew the blow down locking nut and screw (15).
9. Use a pipe wrench to rotate the upper body to free the internals. A flat surface is
provided on the body to get a good grip on the body.
10. Remove the whole internal assembly off the body valve.
11. Unscrew the seat ring (2) and clean the threads.
12. Clean the valve seat (1) and valve head (3). Lap the head against seat in oscillation
motion if required.
13. Reassemble the internals and fit it back in the valve body .
14. Fit the valve back on the pipeline.
15. For seat ring setting refer to section 7.4
16. Fit the easing lever (6) on the valve.
17. Set the valve to set pressure following the steps given in section 6.2.
7.4 Seat Ring Setting: (Refer to Figure 1)
To have the required reset pressure for a particular set pressure, the seat ring (2) should be
adjusted after removing the seat ring locking screw (15). Rotate the seat ring (2) in the
clockwise direction towards the valve (3). Once the seat ring (2) touches the valve (3),
rotate the seat ring (2) in anticlockwise direction, away from the valve (3) by 1/4th of a turn.
Ensure that the seat ring locking screw (15) is tightened and locked after adjustment.

10 Forbes Marshall Safety Relief Valve

8. Troubleshooting:
If the expected performance is unachievable after the installation of the valve, check the following
points for appropriate corrective measures.

Failure Mode Possible Cause Remedy

Check for spring range Refer to the spring ranges given in section 3.3

To have the required reset pressure for a

particular set pressure, the blow down ring
should be adjusted after removing the ring
locking screw. Rotate the blow down ring in the
Check for blow down clockwise direction towards the main valve head.
ring setting Once the blow down ring touches the main
valve head, rotate the ring in anticlockwise
direction, away from the head by 1/4th of a turn
Valve Leakage
Ensure that the screw is tightened after
adjustment.
It is usually sufficient to clean the seating
surfaces and reassemble. If the seating surface
has been damaged it is necessary to re-lap.
Valve seating surface
When reassembling all foreign matter and scales
dirty or damaged
should always be cleared away from the
surrounding components, all lapping paste
removed and seating surface cleaned.

1. It should be only 10% above the working

pressure of the system
Not Releasing Check the pressure
2. Make sure the spring range selected is not
the Pressure setting of the valve
higher than mentioned in section 3.3, for a
given pressure range.

Valve not To have the required reset pressure for a

giving popping particular set pressure, the blow down ring
action and should be adjusted after removing the ring
delay in main locking screw. Rotate the blow down ring in the
Wrong Blow down ring
valve head clockwise direction towards the main valve head.
setting (too far from the
seating (blows Once the blow down ring touches the main
head)
off pressure till valve head, rotate the ring in anticlockwise
it drops off way direction, away from the head by 1/4th of a turn
below the set Ensure that the screw is tightened after
pressure) adjustment.

FMSRV (DN20-50) 11
9. Available Spares:

SPARE
Í ĦÊ Ì Ĕ Î İ ĦĔ SPARE CONSIST OF SPARE CODE
SPECIFICATION
(STEAM SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN20 SPARE-20FMSRV-VHSKIT
EACH
(STEAM SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN25 SPARE-25FMSRV-VHSKIT
EACH
(STEAM SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN40 SPARE-40FMSRV-VHSKIT
EACH
(STEAM SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN50 SPARE-50FMSRV-VHSKIT
VALVE HEAD
EACH
AND SPINDLE
( LIQUID SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
KIT
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN20 SPARE-20FMSRVL-VHSKIT
EACH
(LIQUID SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN25 SPARE-25FMSRVL-VHSKIT
EACH
(LIQUID SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN40 SPARE-40FMSRVL-VHSKIT
EACH
(LIQUID SERVICE) VALVE HEAD ,SPINDLE ,SPINDLE
LOCK NUT ,SEAT RING SCREW & NUT PACK OF 1 DN50 SPARE-50FMSRVL-VHSKIT
EACH
SPINDLE & LOCK NUT PACK OF 1 EACH DN20 SPARE-20FMSRV-SLKIT
FMSRV
SPINDLE & LOCK NUT PACK OF 1 EACH DN25 SPARE-25FMSRV-SLKIT
SPINDLE & LOCK NUT PACK OF 1 EACH DN40 SPARE-40FMSRV-SLKIT

SPINDLE & LOCK NUT PACK OF 1 EACH DN50 SPARE-50FMSRV-SLKIT

SPINDLE AND SPINDLE (LIQUID SERVICE) & LOCK NUT PACK OF 1 DN20 SPARE-20FMSRVL-SLKIT
LOCK NUT EACH
SPINDLE (LIQUID SERVICE) & LOCK NUT PACK OF 1
DN25 SPARE-25FMSRVL-SLKIT
EACH
SPINDLE (LIQUID SERVICE) & LOCK NUT PACK OF 1
DN40 SPARE-40FMSRVL-SLKIT
EACH
SPINDLE (LIQUID SERVICE) & LOCK NUT PACK OF 1
DN50 SPARE-50FMSRVL-SLKIT
EACH
SPRING & SPRING 05-15-PSI,TOP AND BOTTOM SPRING
DN20 SPARE-20FMSRV-5-15SGKIT
GUIDE KIT GUIDE PACK OF 1 EACH

SPRING 15-35-PSI,,TOP AND BOTTOM SPRING

DN20 SPARE-20FMSRV-15-35SGKIT
GUIDE PACK OF 1 EACH
SPRING 35-75-PSI,TOP AND BOTTOM SPRING
DN20 SPARE-20FMSRV-35-75SGKIT
SPRING & GUIDE PACK OF 1 EACH
GUIDE KIT SPRING 75-125-PSI,TOP AND BOTTOM SPRING
DN20 SPARE-20FMSRV-75-125SGKIT
GUIDE PACK OF 1 EACH

SPRING 125-175-PSI,TOP AND BOTTOM SPRING

DN20 SPARE-20FMSRV-125-175SGKIT
GUIDE PACK OF 1 EACH

12 Forbes Marshall Safety Relief Valve

 SPARE
Í ĦÊ Ì Ĕ Î İ ĦĔ SPARE CONSIST OF SPARE CODE
SPECIFICATION
SPRING 175-250-PSI,TOP AND BOTTOM SPRING
DN20 SPARE-20FMSRV-175-250SGKIT
GUIDE PACK OF 1 EACH
SPRING 05-15-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-5-15SGKIT
GUIDE PACK OF 1 EACH
SPRING15-35-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-15-35SGKIT
GUIDE PACK OF 1 EACH
SPRING 35-75-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-35-75SGKIT
GUIDE PACK OF 1 EACH
SPRING 75-125-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-75-125SGKIT
GUIDE PACK OF 1 EACH
SPRING125-175-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-125-175SGKIT
GUIDE PACK OF 1 EACH
SPRING 175-250-PSI,TOP AND BOTTOM SPRING
DN25 SPARE-25FMSRV-175-250SGKIT
GUIDE PACK OF 1 EACH
SPRING 05-15-PSI,TOP AND BOTTOM SPRING
DN40 SPARE-40FMSRV-5-15SGKIT
GUIDE PACK OF 1 EACH
SPRING 15-35-PSI,,TOP AND BOTTOM SPRING
DN40 SPARE-40FMSRV-15-35SGKIT
GUIDE PACK OF 1 EACH
SPRING 35-75-PSI,TOP AND BOTTOM SPRING
DN40 SPARE-40FMSRV-35-75SGKIT
SPRING & GUIDE PACK OF 1 EACH
GUIDE KIT
SPRING 75-125-PSI,TOP AND BOTTOM SPRING
FMSRV GUIDE PACK OF 1 EACH
DN40 SPARE-40FMSRV-75-140SGKIT

SPRING125-175-PSI,TOP AND BOTTOM SPRING

DN40 SPARE-40FMSRV-140-175SGKIT
GUIDE PACK OF 1 EACH

SPRING 175-250-PSI,TOP AND BOTTOM SPRING

DN40 SPARE-40FMSRV-175-400SGKIT
GUIDE PACK OF 1 EACH

SPRING 05-15-PSI,TOP AND BOTTOM SPRING

DN50 SPARE-50FMSRV-5-15SGKIT
GUIDE PACK OF 1 EACH

SPRING 15-35-PSI,TOP AND BOTTOM SPRING

DN50 SPARE-50FMSRV-15-35SGKIT
GUIDE PACK OF 1 EACH

SPRING 35-75-PSI,TOP AND BOTTOM SPRING

DN50 SPARE-50FMSRV-35-75SGKIT
GUIDE PACK OF 1 EACH

SPRING 75-125-PSI,TOP AND BOTTOM SPRING

DN50 SPARE-50FMSRV-75-150SGKIT
GUIDE PACK OF 1 EACH
SPRING 125-175-PSI,TOP AND BOTTOM SPRING
DN50 SPARE-50FMSRV-150-175SGKIT
GUIDE PACK OF 1 EACH
SPRING 175-250-PSI,TOP AND BOTTOM SPRING
DN50 SPARE-50FMSRV-175-500SGKIT
GUIDE PACK OF 1 EACH
VALVE & SEAT VALVE HEAD,SEAT,SEAT RING,RUBBER INSERT ,SEAT
DN20 SPARE-20FMSRV-VSGKIT
KIT (GAS) RING SCREW& NUT PACK OF 1 EACH

FMSRV (DN20-50) 13
 SPARE
Ï Í ĒĨ F Ī J Í F SPARE CONSIST OF SPARE CODE
SPECIFICATION
VALVE HEAD,SEAT,SEAT RING,RUBBER INSERT ,SEAT
DN25 SPARE-25FMSRV-VSGKIT
RING SCREW& NUT PACK OF 1 EACH
VALVE HEAD,SEAT,SEAT RING,RUBBER INSERT ,SEAT
DN40 SPARE-40FMSRV-VSGKIT
RING SCREW& NUT PACK OF 1 EACH
VALVE HEAD,SEAT,SEAT RING,RUBBER INSERT ,SEAT
DN50 SPARE-50FMSRV-VSGKIT
RING SCREW& NUT PACK OF 1 EACH
VALVE & SEAT KIT VALVE HEAD,SEAT,SEAT RING,SEAT RING SCREW& NUT
DN20 SPARE-20FMSRV-VSSKIT
(GAS) PACK OF 1 EACH
VALVE HEAD,SEAT,SEAT RING,SEAT RING SCREW& NUT
DN25 SPARE-25FMSRV-VSSKIT
PACK OF 1 EACH
FMSRV
VALVE HEAD,SEAT,SEAT RING,SEAT RING SCREW& NUT
DN40 SPARE-40FMSRV-VSSKIT
PACK OF 1 EACH
VALVE HEAD,SEAT,SEAT RING,SEAT RING SCREW& NUT
DN50 SPARE-50FMSRV-VSSKIT
PACK OF 1 EACH
ADJUSTMENT BOLT FOR LIQUID APPLICATION DN20 SPARE-20FMSRV-ABKIT

ADJUSTMENT ADJUSTMENT BOLT FOR LIQUID APPLICATION DN25 SPARE-25FMSRV-ABKIT

BOLT
ADJUSTMENT BOLT FOR LIQUID APPLICATION DN40 SPARE-40FMSRV-ABKIT

ADJUSTMENT BOLT FOR LIQUID APPLICATION DN50 SPARE-50FMSRV-ABKIT

How to Order:
Example: 1 No. Forbes Marshall Forbes Marshall Safety Relief Valve, FMSRV, DN20 with BSPT
ends and a set pressure of 6 bar g.
How to Order Spares:
Always order spares by using the description given in the column headed available spares. For
codes refer user manual.

10. Warranty Period:

As per the ordering information and agreement in the contract.
Disclaimer:
This information is strictly proprietary and legally privileged. All contents herein shall be the property of Forbes
Marshall Pvt Ltd and having protection under the intellectual property rights. No part of this information or data may
be distributed or disclosed in any form to any third party. Any dissemination, use, review, distribution, printing or
copying is strictly prohibited, if you are not the intended recipient or user of this information.

Forbes Marshall Pvt Ltd

Manufacturing: B-85, Phase II Chakan Indl Area, Sawardari, Chakan
Tal. Khed, Dist, Pune 410 501. Tel: +91(0)2135 393400
Sales: Opp 106th Milestone, Bombay Pune Road, Kasarwadi,
Pune 411034 Tel.: +91 (0)20 39858555
CIN No: U28996PN1985PTC037806

Email : seg@forbesmarshall.com www.forbesmarshall.com

Doc# FMSS/0317/UM-FMSRV(Dn20-50)/V2.R0