Installation Guide: RADWIN 5000

INSTALLATION GUIDE
RADWIN 5000
Release 4.9
Cat.No. DQ0193780
Table of Contents
Chapter 1: Introduction
1.1 Scope of This Document...................................................................................................... 1‐1
1.2 Notifications ........................................................................................................................ 1‐1
1.3 RADWIN 5000 Overview ..................................................................................................... 1‐2
1.3.1 Sector .......................................................................................................................... 1‐2
1.3.2 Base Station ................................................................................................................ 1‐2
1.3.3 Subscriber Unit ............................................................................................................ 1‐3
1.3.4 Method of Work .......................................................................................................... 1‐4
1.3.5 Sector Management Tools .......................................................................................... 1‐5
1.4 Key Features of RADWIN 5000............................................................................................ 1‐6
1.4.1 General........................................................................................................................ 1‐6
1.4.2 Beamforming Solution (optional)................................................................................ 1‐6
1.5 What’s New in Release 4.9.................................................................................................. 1‐7
Chapter 2: Installation Steps
2.1 Prepare Laptop.................................................................................................................... 2‐2
2.2 Connect Laptop to Radio Unit ............................................................................................. 2‐2
2.2.1 LFF and SFF Units......................................................................................................... 2‐3
2.2.2 JET Units ...................................................................................................................... 2‐4
2.2.3 SU PRO/AIR Units ........................................................................................................ 2‐4
2.3 Update Connectivity Parameters of Radio Unit .................................................................. 2‐4
2.3.1 Legacy HSU (LFF or SFF radio units) ............................................................................ 2‐5
2.3.2 HBS (JET or LFF radio units .......................................................................................... 2‐5
2.3.3 SU PRO/AIR Units ........................................................................................................ 2‐5
2.4 Check items to be installed ................................................................................................. 2‐6
2.5 Prepare Tools ...................................................................................................................... 2‐6
2.6 Install Standard Mounting Kit ............................................................................................. 2‐6
2.6.1 Standard Mounting Kit................................................................................................ 2‐6
2.6.2 Vertical Pole ................................................................................................................ 2‐7
2.6.3 Horizontal Pole .......................................................................................................... 2‐10
2.6.4 Wall ........................................................................................................................... 2‐12
2.7 Install Mounting Kit for the SU PRO/AIR Radio Unit ......................................................... 2‐12
2.8 Mounting a Unit with the Standard Mounting Kit ............................................................ 2‐15
2.9 Ground Radio Unit............................................................................................................. 2‐18
2.9.1 LFF Units.................................................................................................................... 2‐19
2.9.2 SFF Units.................................................................................................................... 2‐19
2.9.3 JET Units .................................................................................................................... 2‐19
2.9.4 SU PRO/AIR Units ...................................................................................................... 2‐20
2.10 Mounting the SU PRO/AIR Radio Unit............................................................................. 2‐21
2.11 Mounting the Lightning Protection Units........................................................................ 2‐23
2.11.1 Mounting the LPU on a pole.................................................................................... 2‐23
2.11.2 Mounting the LPU on a wall.................................................................................... 2‐25
2.12 Connect External Antenna (if applicable)........................................................................ 2‐26
2.13 Waterproofing................................................................................................................. 2‐26
2.14 Connect Radio ................................................................................................................. 2‐27
2.14.1 LFF, SFF and JET Units.............................................................................................. 2‐27
2.14.2 SU PRO/AIR Units .................................................................................................... 2‐29
2.15 Check Connectivity to Radio............................................................................................ 2‐30
2.16 Activate Base Station....................................................................................................... 2‐30
2.17 Align Subscriber Unit....................................................................................................... 2‐30
RADWIN 5000 Installation Guide Release 4.9 i
2.17.1 LFF and SFF Units..................................................................................................... 2‐31
2.17.2 SU PRO/AIR Units .................................................................................................... 2‐32
Chapter 3: Safety Practices and Provisions
3.1 Scope of this Chapter .......................................................................................................... 3‐1
3.1.1 Preventing Overexposure to RF Energy ....................................................................... 3‐1
3.1.2 Grounding ................................................................................................................... 3‐1
3.1.3 Protection against Lightning ....................................................................................... 3‐1
3.1.4 General........................................................................................................................ 3‐2
3.1.5 Internal ESD Protection circuits ................................................................................... 3‐2
Appendix A: Terminology
Appendix B: Wiring Specifications
B.1 Radio unit‐PoE Cable (HBS and HSU) .................................................................................. B‐1
B.2 User Port Connectors .......................................................................................................... B‐2
B.2.1 LAN Port ...................................................................................................................... B‐2
B.3 DC Power Terminals ............................................................................................................ B‐3
B.3.1 DC PoE ......................................................................................................................... B‐3
B.4 SU2‐AC Power Terminal ...................................................................................................... B‐3
Appendix C: Setting Antenna Parameters
C.1 Antenna Issues .................................................................................................................... C‐1
C.2 About Single and Dual Antennas......................................................................................... C‐1
C.3 Considerations for Changing Antenna Parameters............................................................. C‐3
Appendix D: Regional Notice: French Canadian
D.1 Procédures de sécurité .......................................................................................................D‐1
D.2 Installation sur pylône et mur.............................................................................................D‐3
Appendix E: RF Exposure
Appendix F: Revision History
RADWIN 5000 Installation Guide Release 4.9 ii
Chapter 1: Introduction
1.1 Scope of This Document
This document shows how to install RADWIN 5000 radios.
For a detailed description of how to configure RADWIN 5000 radios and sectors, see the
RADWIN 5000 Configuration Guide.
1.2 Notifications
Notifications consist of Notes, Cautions, and Warnings:
Caution: Risk of damage to equipment or of service degradation
Warning: Risk of danger to persons operating near the equipment
The purpose of a Note is to:
• Draw your attention to something that may not be obvious
• Emphasize a special feature
• Provide additional background
RADWIN 5000 Installation Guide Release 4.9 1‐1

RADWIN 5000 Overview Introduction
1.3 RADWIN 5000 Overview
1.3.1 Sector
The RADWIN 5000 system consists of a “sector” that includes a base station, and at least one
subscriber unit. The subscriber units are installed and work opposite the base stations.
Figure 1‐1: A RADWIN 5000 Sector
1.3.2 Base Station
There are two types of base stations, both of which are High Capacity Base Stations (HBS):
• Large Form Factor (LFF) ‐ With an integrated or external antenna
Figure 1‐2: LFF base station with inte‐ Figure 1‐3: LFF base station connec‐
grated antenna torized for external antenna
• Beamforming (JET) ‐ With an integrated antenna

Subscriber Unit Introduction
Figure 1‐4: RADWIN 5000 JET
1.3.3 Subscriber Unit
There are two types of RADWIN 5000 subscriber units:
High Capacity Subscriber Unit (HSU)
An HSU can have one of the following resource allocations:
• CIR ‐ Committed Information Rate: receives a guaranteed percentage of resources
• BE ‐ Best Effort: receives resources according to availability
In addition, an HSU can have one of the following form factors:
• Large Form Factor (LFF) ‐ Its external appearance is similar to a Large Form Factor
HBS, and can have an integrated or external antenna.
Figure 1‐5: LFF subscriber unit with Figure 1‐6: LFF subscriber unit connec‐
integrated antenna torized for external antenna
• Small Form Factor (SFF) ‐ As its name implies, this unit is smaller than an LFF unit,
but can also have an integrated or external antenna.
Figure 1‐7: SFF subscriber unit with Figure 1‐8: SFF subscriber station con‐
integrated antenna nectorized for external antenna

Method of Work Introduction
SU PRO/AIR
• SU PRO ‐ Can operate using the CIR or BE resource type
• SU AIR ‐ Operates using the BE resource type only.
Figure 1‐9: SU PRO/AIR unit
1.3.4 Method of Work
Both the base stations and the subscriber units communicate respectively, with the service
provider and users through PoE devices. The communication protocol for both the service
provider and the users is Ethernet.
See figure 1‐10, RADWIN 5000 Connection Scheme:
• The PoE device is connected to power and the communications network:
• On the base station side, the PoE is connected to the backhaul network
• On the subscriber unit side, the PoE is connected to end‐user equipment: routers,
WiFi devices, etc.
• Using CAT‐5e cables, the radio units are connected to power and the communications
network via a Power‐over‐Ethernet (PoE) device.
• The radio units and PoE devices are also connected to ground.
• The Base Station communicates with the Subscriber Unit or Units via the air interface.
For simplicity, Lightning Protection Units (LPU) are not shown in Figure 1‐10, but
these are recommended. See see Mounting the Lightning Protection Units on
page 2‐24 for directions on how to install the LPUs.

Sector Management Tools Introduction
Figure 1‐10: RADWIN 5000 Connection Scheme
1.3.5 Sector Management Tools
WINTouch
WINTouch is a mobile application that guides you in installing and aligning SU PRO/AIR
devices, as well as base stations that work with them.
RADWIN Web Interface
The Web Interface enables you to carry out basic unit and/or sector management functions
using a Web browser. It is an easy way to rapidly configure and setup a link.

Key Features of RADWIN 5000 Introduction
It may be used to ‐
• Set or change basic radio unit parameters in the field
• Establish a sector on a minimal basis
• Check link parameters and make basic changes
• View the link Inventory
• Inspect the Recent Events logs
The Web Interface for the SU PRO/AIR and for legacy HBS and HSU radios are
different. When configuring and aligning the SU PRO/AIR, use its Web Interface
only.
RADWIN Manager
The RADWIN Manager is an SNMP‐based management application which manages a
complete sector over a single IP address.
1.4 Key Features of RADWIN 5000
1.4.1 General
» Ethernet connectivity
» Advanced OFDM & MIMO 2x2 for nLOS and NLOS performance
» Enhanced interference mitigation capability
» Inter & intra site sync to reduce self interference
» Multiband radios: Different frequencies in the same radio unit
» Dedicated Bandwidth ensuring SLA & latency
» Regulations supported ‐ FCC/IC/ETSI/WPC/MII/Universal
» Up to 32 Subscriber Units per base station
» Fully integrated with RADWIN Legacy solutions:
• Base station can coexist with RADWIN 2000 and WinLink 1000 products
• Common RADWIN Manager
» Nomadic support (standard in all base station models)
1.4.2 Beamforming Solution (optional)
» Smart beamforming antenna, integrated in dedicated base station
» On‐the‐fly beamforming capability reduces interference, increases efficiency
» Narrow beam
» Support for ethernet‐based synchronization
» Integrated GPS synchronization capability

Beamforming Solution (optional) Introduction
For complete and comprehensive characteristics of the specific model you are
working with, refer to its Data Sheet.

Chapter 2: Installation Steps
To install and establish a basic connection with a radio unit, carry out the steps shown below.
Print out this list, and place a checkmark next to a completed task.
Table 2‐1: Installation Check‐List
Step Action Page Done?
Before deploying at installation site
1. Prepare Laptop page 2‐2
2. Connect Laptop to Radio Unit page 2‐2
3. Update Connectivity Parameters of Radio Unit page 2‐4
4. Check items to be installed page 2‐6

5. Prepare Tools page 2‐7
Installation
6. Install Standard Mounting Kit page 2‐7
7. Install Mounting Kit for the SU PRO/AIR Radio Unit page 2‐13
8. Mounting a Unit with the Standard Mounting Kit page 2‐16
9. Ground Radio Unit page 2‐19
10. Mounting the SU PRO/AIR Radio Unit page 2‐22
11. Mounting the Lightning Protection Units page 2‐24
12. Connect External Antenna (if applicable) page 2‐27
13. Waterproofing page 2‐27
Commissioning
14. Connect Radio page 2‐28
15. Check Connectivity to Radio page 2‐31
16. Activate Base Station page 2‐31
17. Align Subscriber Unit page 2‐31

Prepare Laptop Installation Steps
2.1 Prepare Laptop
Configure IP address and subnet mask of laptop as follows:
• Control Panel ‐> Network and Internet ‐> Network and Sharing Center ‐> Change
Adapter settings ‐> click on Network Interface Card name
• Properties ‐> Select Internet Protocol Version 4 (TCP/IPv4) ‐> Properties ‐> set IP address
to 10.0.0.100 and Subnet mask to 255.255.0
2.2 Connect Laptop to Radio Unit
Connect PoE to power, connect the laptop’s ethernet port to the IN (or LAN) socket on the
PoE, then connect the OUT (or PoE) socket on the PoE to the appropriate socket on the radio
unit.
Figure 2‐1: Connecting laptop to a radio unit

RADWIN 5000 (LFF and SFF) Units Installation Steps
2.2.1 RADWIN 5000 (LFF and SFF) Units
Connect to socket labeled ‐> “IDU”
Figure 2‐2: Laptop/network port: LFF radio unit
Figure 2‐3: Laptop/network port: SFF radio unit

JET Units Installation Steps
2.2.2 JET Units
Connect to socket labeled ‐> “PoE In”
Figure 2‐4: Laptop/network port: JET radio unit
2.2.3 SU PRO/AIR Units
Connect to ‐> Input socket (not labeled)
Figure 2‐5: Laptop/network port: SU PRO/AIR radio unit
2.3 Update Connectivity Parameters of Radio
Unit
1. In an internet browser, enter http:// 10.0.0.120
2. Enter User Name admin and Password netman.
3. Click Log In.
4. Continue according to the type of radio unit you are using:

HSU: RADWIN 5000 (LFF or SFF radio units) Installation Steps
2.3.1 HSU: RADWIN 5000 (LFF or SFF radio units)
a. Click Config.
b. Click Management.
c. Enter new IP Address, Subnet Mask, and Default Gateway.
d. Click Save and exit browser.
e. From a command line, ping radio unit using new IP address to verify change.
2.3.2 HBS: RADWIN 5000 or JET radio units
a. Install the RADWIN Manager application from: http://www.radwin.com/
download, or use the QR code:
b. Log on to the RADWIN Manager as
an “Installer” and enter the default
IP address (http://10.0.0.120) and
password: wireless.

SU PRO/AIR Units Installation Steps
c. From the RADWIN Manager, click
Activate, and follow the instructions in
the wizard.
d. During the course of the wizard, enter the
new management IP Address, Subnet
Mask, and Default Gateway, Sector ID,
operating channel, and channel
bandwidth.
f. Once you are finished with the steps above, disconnect the radio unit and prepare it
for deployment in the field.
a. Click Configure
b. Click Network
c. Enter new IP Address, Subnet Mask, and Default Gateway.
d. Click Apply All and exit browser.
f. Once you are finished with the steps above, disconnect the radio unit and prepare it
for deployment in the field.
Alternatively, you can use the WINTouch smartphone application to change the IP
address. Log on to WINTouch and follow the instructions.
2.4 Check items to be installed
• Radio unit + mounting kit
• 2 LPUs for each radio (recommended)
• PoE (if outdoor, requires mounting kit)
• CAT‐5e cables
• Grounding cables (10 AWG) for radio unit, LPUs and outdoor PoE (if used)
• External antenna + mounting kit (if using an external antenna)

Prepare Tools Installation Steps
• RF cables (if using an external antenna)
2.5 Prepare Tools
• Crimping tool
• Spanner/wrench 13mm (1/2”)
• Cable ties
• Sealing material
• Waterproofing tape (like Scotch 23)
2.6 Install Standard Mounting Kit
2.6.1 Standard Mounting Kit
Use the standard mounting kit for:
• LFF (large form‐factor) radio units
• SFF (small form‐factor) radio units
• JET radio units
• External PoEs
• RADWIN GSUs
• External antennas (with mounting kit adaptor)

Vertical Pole Installation Steps
Figure 2‐6: Mounting Kit Contents
Tighten all bolts with a torque of 15Nm.
The mounting kit can be used on a vertical or horizontal pole or on a wall:
Vertical Pole page 2‐8

Horizontal Pole page 2‐11
Wall page 2‐13
2.6.2 Vertical Pole
The mounting kit can be used on a thin, medium, or thick pole.
Thin Pole Dia. 3/4 ‐1 1/2 page 2‐9
Medium Pole Dia. 2 ‐ 3 page 2‐9

Thick Pole Dia. > 3 page 2‐10

Thin Pole
1. Diameter 3/4 to 1 1/2: Position the pole clamp as shown in the following figures.
Do not tighten the bolts all the way.
Figure 2‐7: Connect Pole Clamp to Radio Figure 2‐8: Partially tighten bolts
Holder
2. Place this “unit” on the pole where you want to mount the device. Once it is in
place, rotate the pole clamp as shown, then tighten both bolts.
Figure 2‐9: Rotate Clamp and tighten bolts Figure 2‐10: Completely tighten bolts
Medium Pole
1. Diameter 2 to 3: Position the pole clamp as shown in the following figures. Do not tighten
the bolts all the way.
Figure 2‐11: Connect Pole Clamp to Radio Figure 2‐12: Tighten bolts
Holder

2. Place this “unit” on the pole where you want to mount the device. Once it is in
place, rotate the pole clamp as shown, then tighten both bolts.
Figure 2‐13: Rotate Clamp Figure 2‐14: Completely tighten bolts
Thick Pole
1. Diameter larger than 3: Use worm drive clamps (not supplied), threaded through the holes
as shown:
Figure 2‐15: Mounting kit on a thick pole
The pole clamp is not needed.

Horizontal Pole Installation Steps
JET Radio Unit
When mounting a JET radio unit on a vertical pole, use the radio vertical adaptor as shown:
Figure 2‐16: JET radio unit mounted on a vertical pole
2.6.3 Horizontal Pole
Installing the mounting kit on a horizontal pole is done in a similar manner to that on a
vertical pole (thin, medium, or thick sizes):

Figure 2‐17: Mounting Kit on a horizontal pole

Horizontal Pole Installation Steps
When mounting a Large Form‐Factor (LFF) radio unit, Small Form‐Factor (SFF) radio unit, GSU,
PoE, or external antenna on a horizontal pole, use the radio vertical adaptor:
Figure 2‐18: Radio unit mounted on a horizontal pole
When mounting a JET radio unit on a horizontal pole, the vertical adaptor is not needed:

Figure 2‐19: JET radio unit mounted on a horizontal pole

Wall Installation Steps
2.6.4 Wall
Use two mounting screws (not included) appropriate for the type of wall to install the
mounting kit on a wall. Make sure you use the indicated holes.
The pole clamp is not needed.

Figure 2‐20: Mounting kit on a wall
2.7 Install Mounting Kit for the SU PRO/AIR
Radio Unit
The SU PRO/AIR has its own mounting kit. Mount this unit as shown in the steps below:
1. Place the mount on a pole or wall:
2. Secure the mount using the worm drive clamps. These are “quick‐release” clamps,
and work as follows:
a. Open the clamp:

Install Mounting Kit for the SU PRO/AIR Radio Unit Installation Steps
b. Slide the metal band through the mount:
c. Slide the metal band through the clamp:
d. Adjust the radius of the band, and lock it with the clamp:
e. Once the band is at the correct radius, close the clamp and tighten with a
screwdriver:

Install Mounting Kit for the SU PRO/AIR Radio Unit Installation Steps
3. Alternatively, you can fasten the mount with screws (not included) appropriate for
the surface being used:

Mounting a Unit with the Standard Mounting Kit Installation Steps
2.8 Mounting a Unit with the Standard
Mounting Kit
Fasten an LFF (large form‐factor), SFF (small form‐factor) JET radio units, as well as external
PoEs, and RADWIN GSUs, and external antennas to the mounting kit as shown in Figure 2‐21
to Figure 2‐23:
(if mounting a flat‐panel antenna, see page 2‐18).
Figure 2‐21: Mounted LFF radio unit
Figure 2‐22: Mounted SFF radio unit or GSU
Figure 2‐23: Mounted PoE

For JET radio units, mount as shown in Figure 2‐24 and Figure 2‐25:

• Use the radio vertical adaptor when mounting a JET unit on a vertical pole
Figure 2‐24: JET radio unit mounted on a vertical pole
• When mounting a JET unit on a horizontal pole, the radio vertical adaptor is not needed:
Figure 2‐25: JET radio unit mounted on a horizontal pole

Flat panel antenna
If mounting a flat panel antenna, a mounting kit adapter is required (see Figure 2‐26):
Figure 2‐26: Flat panel antenna mounting kit adapter
Attach the mounting kit adaptor to the rear of the external antenna as shown:
Figure 2‐27: Flat Panel antenna ‐ rear with mounting kit adapter
Mount the antenna with the adaptor to a vertical or horizontal pole (as shown in Figure 2‐21
to Figure 2‐22).
Figure 2‐28 shows a mounted antenna. Attach the mounting bolt to the side of the adaptor
with the recess, as shown.

Ground Radio Unit Installation Steps
Figure 2‐28: Flat Panel antenna ‐ mounted on a pole
2.9 Ground Radio Unit
Connect a ground cable to the indicated ground connection on the radio unit as shown in the
sections below:

LFF Units Installation Steps
2.9.1 LFF Units
Figure 2‐29: Ground: LFF radio unit
2.9.2 SFF Units
Figure 2‐30: Ground: SFF radio unit
2.9.3 JET Units
Figure 2‐31: Ground: JET radio unit

Since the SU PRO/AIR is grounded via its mounting kit, it must be grounded before being
mounted.
Figure 2‐32: Ground: SU PRO/AIR radio unit

Mounting the SU PRO/AIR Radio Unit Installation Steps
2.10 Mounting the SU PRO/AIR Radio Unit
1. Open the clamp (for radio unit):
2. Position the radio unit so that the knobs on the mounting ball on the rear are
opposite the slots on the mount:

Mounting the SU PRO/AIR Radio Unit Installation Steps
3. Firmly place the radio unit into the mount until you hear a click:
4. Close the clamp half‐way:
5. Keep the clamp half‐closed until the alignment procedure is complete.

Mounting the Lightning Protection Units Installation Steps
2.11 Mounting the Lightning Protection Units
• We recommend using two lightning protection units (LPUs) for each radio unit installa‐
tion: One near the radio unit and one near the PoE.
• The LPU can be mounted on a pole or on a wall.
• Make sure the LPU is oriented with the cable glands oriented towards the bottom.
• Mount one LPU near the radio unit, and the second near the PoE:
2.11.1 Mounting the LPU on a pole
1. Insert the metal band through the slots on the LPU as shown:

Mounting the LPU on a pole Installation Steps
2. Tighten the metal band.
3. Connect the grounding lug to a ground source.
4. Remove the cable glands, and thread the CAT‐5e cables through them:

Mounting the LPU on a wall Installation Steps
5. Connect the cables to the LPU’s sockets, and the glands around the cables as
shown:
6. Route one CAT‐5e cable up to the radio unit, and the other down to the PoE (via
the lower LPU). An LPU installed on a pole is shown below:
2.11.2 Mounting the LPU on a wall
1. Remove the grounding lug.
2. Fasten the LPU to the wall using screws appropriate for the wall (screws not
included).
3. Connect the left screw (where the grounding lug was located) to a grounding
source via a grounding cable.

Connect External Antenna (if applicable) Installation Steps
4. Attach the CAT‐5e cables as shown in Steps 4. and 5. above.
2.12 Connect External Antenna (if applicable)
Applicable only if you are using an external antenna, with a connectorized radio unit.
• Connect 2 RF cables to external antenna.
• Connect the RF cables to the radio unit.
2.13 Waterproofing
Protect all outdoor connections1 from rain, dust, moisture and salt by taping the cable/gland
connection with an appropriate sealant tape. We recommend using ScotchTM 23 splicing tape
or similar.
Figure 2‐33: Sealant tape
Add tape as shown below.
1. This is not required for the SU PRO/AIR unit

Connect Radio Installation Steps
Figure 2‐34: Applying sealant tape to an external connection
2.14 Connect Radio
2.14.1 LFF, SFF and JET Units
1. Connect a CAT‐5e cable to the input port of the radio as shown:
Figure 2‐35: Input port: LFF unit
Connection label: “IDU”
Figure 2‐36: Input port: SFF unit

LFF, SFF and JET Units Installation Steps
Connection label: “IDU”
Figure 2‐37: Input port: JET unit
Connection label: “PoE In”
2. Add sealant tape to the connections as described in Chapter 2, Waterproofing.
3. Route the CAT‐5e and ground cables down from the radio to a PoE via 2 LPUs: one
near the radio, one near the PoE. Fasten CAT‐5e cable connections with a cable
gland, add sealant tape.
4. Connect ground cable to ground.
5. Perform final connections via a PoE, depending on the type of PoE you are using,
as follows:
Indoor PoE
a. Connect CAT‐5e cable from lower LPU to “Out” port
b. Connect LAN cable to “In” port.
c. Connect power cable

Outdoor PoE
Connect CAT‐5e cable from lower LPU to “PoE” port, fasten with gland, add tape.
a. Connect LAN cable to “ETH” port, fasten with cable gland, add tape.
b. Connect ground cable.
c. Connect power cable
1. Connect a CAT‐5e cable to the input port of the radio as shown:
Figure 2‐38: Input port: SU PRO/AIR unit
Connection label: None
2. Route the CAT‐5e and ground cables down from the radio to a PoE.
• Recommend, although not required: route the CAT‐5e cable via 2 LPUs: one near
the radio, one near the PoE. Fasten CAT‐5e cable connections with gland, add seal‐
ant tape.
3. Connect ground cable to ground.
4. Perform final connections via the SU PRO/AIR PoE:

Check Connectivity to Radio Installation Steps
5. Connect CAT‐5e cable from lower LPU to the “PoE” port.
6. Connect LAN cable to “LAN” port.
7. Connect power cable.
2.15 Check Connectivity to Radio
1. Connect to radio unit:
• From a laptop in the field: Disconnect the PoE from the communications network
(LAN connection), and connect the laptop.
• From the NOC: Keep the PoE connected to the LAN.
2. From a command line, ping radio using radio’s IP address.
2.16 Activate Base Station
Applicable only if you are installing a base station.
1. Connect to radio unit:
• From a laptop in the field: Disconnect the PoE from the communications network
(LAN connection), and connect the laptop.
• From the NOC: Keep the PoE connected to the LAN.
2. Log on to the RADWIN Manager application as “Installer”.
3. Enter IP address of Base Station (HBS).
4. From main window of the RADWIN Manager application, click Activate.
5. Follow wizard instructions to activate radio.
2.17 Align Subscriber Unit
• Make sure the subscriber unit’s base station is activated (check with the NOC).
• Point the subscriber unit in the general direction of its base station.
• Continue according to the type of subscriber unit you are using:

LFF and SFF Units Installation Steps
2.17.1 LFF and SFF Units
1. Align the unit horizontally (in azimuth):
a. Swivel the unit 90o to the left slowly, 180o to the right, and then 90o back towards
the base station.
Figure 2‐39: Swivel horizontally (SFF unit shown)
b. While swiveling the unit, listen to the buzzer beep sequence until optimal
alignment is achieved (3 beeps and a pause, as shown below).
2. Repeat the above in elevation.
Figure 2‐40: Swivel vertically (LFF unit shown)
3. Once alignment is complete, tighten the bolt holding the radio on the mounting
kit.

• The subscriber unit will stop beeping when it is aligned with the base station, and con‐
figured.
• You can manually cease the beeping via the RADWIN Manager application.
1. Connect to the unit via WiFi using a smartphone.
2. Operate the WINPRO application, and follow its instructions.

3. Once alignment is complete, tighten the arm on the mounting kit (see Figure 2‐
41).
4. If the unit requires more tightening, use the hex screw with a 5mm hex key as
shown in Figure 2‐42.
Figure 2‐41: Tighten arm on mount: SU PRO/AIR radio unit
Figure 2‐42: Use hex screw to further tighten arm on mount: SU PRO/AIR radio unit

Chapter 3: Safety Practices and
Provisions
3.1 Scope of this Chapter
This chapter describes various safety practices.
3.1.1 Preventing Overexposure to RF Energy
To protect against overexposure to RF energy, install the radio units so as to provide and
maintain minimal separation distances from all persons.
When the system is operational, avoid standing directly in front of the antenna. Strong RF
fields are present when the transmitter is on. The radio unit must not be deployed in a
location where it is possible for people to stand or walk inadvertently in front of the antenna.
3.1.2 Grounding
All RADWIN products should be grounded during operation. In addition:
• All ODUs should be grounded by a wire with diameter of at least 10 AWG.
• The ground lug on an IDU‐H should be connected to the protective earth at all times, by
a wire with a diameter of 18 AWG or wider.
• Rack‐mounted equipment should be mounted only in grounded racks and cabinets.
Further, you should ‐
• Always make the ground connection first and disconnect it last
• Never connect telecommunication cables to ungrounded equipment
• Ensure that all other cables are disconnected before disconnecting the ground
3.1.3 Protection against Lightning
The use of lightning protection is dependent on regulatory and end user requirements. All
RADWIN outdoor units are designed with surge limiting circuits to minimize the risk of

General Safety Practices and Provisions
damage due to lightning strikes. RADWIN recommends the use of additional surge arrestor
devices to protect the equipment from nearby lightning strikes.
3.1.4 General
• It is recommended that installation of outdoor units be contracted to a professional
installer
• Before working on equipment connected to power lines or telecommunication lines,
remove jewelry or any other metallic object that may come into contact with energized
parts
• Use extreme care when installing antennas near power lines
• Use extreme care when working at heights
• When using an AC power source for RADWIN devices, always use the AC power adapter
supplied by RADWIN
• Use the right tools!
• Do not mount an radio unit upside down or horizontally. Doing this may void you prod‐
uct warranty.
3.1.5 Internal ESD Protection circuits
RADWIN equipment is designed to meet the ETSI/FCC/Aus/NZ/CSA EMC and Safety
requirements. To fulfill these requirements, the system's Telecom lines at the radio unit/PoE
are Transformer‐isolated and include internal ESD (Electro‐Static‐Discharge) Protection
circuits.
When installing an AC powered HSU: To maintain Overvoltage
(Installation) Category II, install a suitable surge suppressor device in the
branch circuit to limit expected transients to Overvoltage Category II
values.
The limits are based on IEC60664 and are also located in Table 2H of
UL60950 (for mains ≤ 150V, the transient rating is 1500V; for 150V < mains
≤ 300V, the transient rating is 2500V; and for 300V < mains ≤ 600V, the
transient rating is 4000V).

Appendix A: Terminology
Table A‐1: Terminology (Sheet 1 of 3)
Term Description
Assured throughput Actual number of timeslots allocated to a radio unit.
Automatic Channel Selection. Option that instructs the radio to
ACS choose which frequency to use. Enabling or disabling this option
has various ramifications as shown in the documentation.
ATPC Automatic Transmit Power Control
Best Effort: A level of priority for traffic in which users receive
BE dynamic resource allocation according to overall demand. They
are not guaranteed resources. See also CIR.
Base Station: a radio that can transmit and receive to more than
BS
one point. See also HBS
Committed Information Rate: A level of priority for traffic in which
CIR users receive a guaranteed percentage of resources in addition to
dynamic resources if available. See also BE.
CPE Customer Premises Equipment
Dynamic Bandwidth Allocation: a method that allocates
DBA bandwidth between the various users of that same bandwidth in
the network.
Dynamic Host Configuration Protocol: a protocol that
DHCP automatically assigns IP addresses and other network
configuration parameters.
A technique by which the reliability of a radio link is increased
Diversity using multiple transmitting and receiving antennas, transmitting
the same signal on all antennas.
Data traffic from an HBS to an HSU, or
Downlink
Data traffic from an RT‐A to an RT‐B
RADWIN 5000 Installation Guide Release 4.9 A‐1

Term Description
Equivalent (or Effective) Isotropically Radiated Power: The power
that an antenna must emit to produce the peak power density in
EIRP the direction of maximum antenna gain. In our cases, this is
usually: System Tx Power + Antenna
Gain ‐ Cable Loss.
Federal Aviation Administration. A U.S. federal office that manages
FAA
aviation regulations throughout the United States.
A “fixed” HSU remains in one location, as contrasted with a
Fixed (HSU)
nomadic or mobile HSU, which does not remain in one location.
GHSS GPS Hub Site Synchronization
HBS High capacity Base Station. Same as a BS
High capacity Mobility (subscriber) Unit. Similar to an HSU, but can
HMU
be mobile.
Hub Sync Client: When using Hub Site Synchronization, one unit is
HSC a master (generates the sync pulses), and the other units are
clients.
Hub Sync Master: When using Hub Site Synchronization, one unit
HSM is a master (generates the sync pulses), and the other units are
clients.
HSU High capacity Subscriber Unit. Same as an SU
Integrated Synchronization Unit: a network device that provides a
ISU
synchronization signal to underground HBSs.
ITHO Intra‐train handover mechanism
LFF Large Form‐Factor
Multiple In, Multiple Out. A technique by which the capacity of a
MIMO radio link is increased using multiple transmitting and receiving
antennas, transmitting a different signal on all antennas.
MIR Maximum Information Rate
A “mobile” HSU can move from location to location and provide
Mobile (HSU)
service while it moves or when it is stationary.
A “nomadic” HSU move from location to location but can only
Nomadic (HSU)
provide service when it is stationary.
Outdoor Unit: a generic term for any radio, and can usually be
ODU
exchanged for HBS or HSU.
PtMP Point to Multi‐Point: link from an HBS to several HSUs
PtP Point to Point
RADIUS Remote Authentication Dial‐In User Service

Term Description
QoS Quality of Service
SBM Smart Bandwidth Management
A group of radios that consists of one HBS and several HSUs that
Sector
communicate with the HBS.
SFF Small Form‐Factor
SLA Service Level Agreement
Synchronization Status Message: Provides traceability of
SSM synchronization signals, and is used in the Synchronous Ethernet
standard of communication.
Subscriber Unit: a radio that can transmit and receive to one point.
SU
See also HSU
Synchronous Ethernet: A standard of communication for ethernet
Sync E or SyncE that provides a synchronization signal to network elements that
need such a signal.
Transportation Base Station. Similar to an HBS or BS, but used with
TBS
high‐speed transportation applications.
Terminal Doppler Weather Radar: a type of radar station used in
the U.S. and other countries for weather reporting. If a radio unit is
TDWR installed close enough to one of these stations, the FCC requires
that certain actions must be taken on the part of the customer.
Regulations in other countries varies.
TMU Transportation Mobile Unit. Similar to an SU
Items or subject matter that relates to the environment not on or
Track Side
inside the train. It is not limited to precisely next to the track.
Items or subject matter that relates to the environment on or
Train Side
inside the train itself.
Data traffic from an HSU to an HBS, or
Uplink
Data traffic from an RT‐B to an RT‐A
VMU Vehicular Mobile Unit
Web Interface: web‐based application that provides simple
WI
configuration capabilities for the radio units.
Wireless Internet Service Provider Association. An organization
WISPA that manages registration of wireless devices that operate close to
TDWR facilities run by the FAA.

Appendix B: Wiring
Specifications
B.1 Radio unit‐PoE Cable (HBS and HSU)
The radio unit‐PoE cable is shielded/outdoor class CAT‐5e, 4 twisted‐pair 24 AWG terminated
with RJ‐45 connectors on both ends. A cable gland on the radio unit side provides hermetic
sealing.
The following table shows the connector pinout:
Table B‐1: Radio unit‐PoE RJ‐45 Connector Pinout
Function Color PoE ODU
Rx N White/Green 1 1
Rx T Green 2 2
Tx T White/Orange 3 3
Tx N Orange 6 6
Power (+) Blue 4 4
Power (+) White/Blue 5 5
Power () White/Brown 7 7
Power () Brown 8 8
Table B‐2: LAN‐GbE PoE RJ‐45 Connector Pinout
Function Color PoE LAN
TxRx A White/Green 1 1
TxRx A Green 2 2
TxRx B White/Orange 3 3
TxRx B Orange 6 6
RADWIN 5000 Installation Guide Release 4.9 B‐1

User Port Connectors
Table B‐2: LAN‐GbE PoE RJ‐45 Connector Pinout (Continued)
Function Color PoE LAN
TxRx C & Power(+) Blue 4 4
TxRx C & Power(+) White/Blue 5 5
TxRx D & Power(‐) White/Brown 7 7
TxRx D & Power(‐) Brown 8 8
B.2 User Port Connectors
B.2.1 LAN Port
The LAN 10/100BaseT interface terminates in an 8‐pin RJ‐45 connector, wired in accordance
to Table B‐3.
Table B‐3: Fast Ethernet Connector Pinout
Function Signal Pin
Transmit Data (positive) TD (+) 1
Transmit Data (negative) TD (–) 2
Receive Data (positive) RD (+) 3
Receive Data (negative) RD (–) 6

DC Power Terminals
B.3 DC Power Terminals
B.3.1 DC PoE
Table B‐4: Terminal Block 2‐pin ‐48VDC
Function Pin
+ Right
– Left
B.4 SU2‐AC Power Terminal
The SU2‐AC power port is a four pin male socket with pin assignments as follows:
Table B‐5: SU2‐AC power pin assignments
Pin Wire Color Function
1 Red Line
2 Not used
3 Black Neutral
Green or Green‐
4 Ground
Yellow

Appendix C: Setting Antenna
Parameters
C.1 Antenna Issues
The choice of Tx Power, antenna gain and cable loss (between the radio and the antenna)
determines the EIRP and is affected by such considerations as radio limitations and regulatory
restrictions.
Before proceeding to antenna installation details, the following background information
should be considered:
C.2 About Single and Dual Antennas
Each RADWIN 5000 HPMP ODU is made of two radio transceivers (radios). The radios make
use of algorithms that utilize both Spatial Multiplexing and Diversity resulting in enhanced
capacity, range and link availability. The number of antennas (i.e. radios) used is determined
by user configuration and by automatic system decisions, explained below.
C.2.1 Dual Antennas at the HBS and an HSU
When using dual antennas at both sites (single bipolar antenna or two mo‐unipolar antennas)
you can choose between Spatial Multiplexing Mode and Diversity Mode.
Spatial Multiplexing Mode
Under this mode, the system doubles the link capacity. At the same time, it keeps the same
rate and modulation per radio as was used with single antenna, thus increasing capacity,
range and availability.
For example with a dual antenna RADWIN 5000 HPMP can transmit at modulation of 64QAM
and FEC of 5/6 and get an air rate of 130 Mbps, compared to 65 Mbps with single antenna.
To work in this mode, each antenna port must be connected to an antenna, the RSS level in
both receivers should be balanced and a minimal separation between the antennas must be
RADWIN 5000 Installation Guide Release 4.9 C‐1

maintained. (For example, by using dual polarization antennas a cross polarization separation
is attained).
Upon selecting Antenna Type as Dual, RADWIN 5000 HPMP automatically selects this mode
and doubles the air rates.
RADWIN Manager indicates a case of unbalanced RSS between the two antennas in the HBS
panels.
Diversity Mode
Diversity Mode uses two antennas to improve the quality and reliability of the link. Often,
there is not a clear line‐of‐sight (LOS) between transmitter and receiver. Instead the signal is
reflected along multiple paths before finally being received.
Each such “bounce” can introduce phase shifts, time delays, attenuations, and even
distortions that can destructively interfere with one another at the aperture of the receiving
antenna. Antenna diversity is especially effective at mitigating these multi‐path situations.
This is because multiple antennas afford a receiver several recordings of the same signal. Each
antenna will be exposed to a different interference environment. Thus, if one antenna is
undergoing a deep fade, it is likely that another has a sufficient signal. Collectively such a
system can provide a robust link.
Antenna diversity requires antenna separation which is possible by using a dual‐polarization
antenna or by two spatially separated antennas.
Use Diversity instead of Spatial Multiplexing in the following situations:
• When the system cannot operate in Spatial Multiplexing Mode
• When one of the receivers has high interference compared to the second receiver (i.e.
the system is “unbalanced”)
• When you achieve higher capacity in Diversity Mode than in Spatial Multiplexing Mode
• When high robustness is of importance and the capacity of Diversity Mode is sufficient
(up to 25 Mbps full duplex)
C.2.2 Single Antennas at Both Sites
By selecting a single antenna at the HBS and HSU, the ODUs operate with a single radio that is
connected to the ANT 1 connector. The second radio is automatically shut down.
C.2.3 Single at One Site, Dual Antennas at the Other
In this mode one of the sites uses the ODU with a single antenna while the other site uses the
ODU with a dual antenna.
The advantages in this mode in comparison to using a single antenna in both sites are
doubled total Tx Power and additional polarization and/or space diversity (depending on the
polarization of installed antennas).
The air rates used in this mode are same as when using single antennas in both sites.

Table C‐1 summarizes the situation: (SM =Spatial Multiplexing)
Table C‐1: Spatial Multiplexing ‐ Diversity settings
Number of Max Full
Mode
Antennas Duplex
Site A Site B Site A Site B Capacity
Spatial Spatial
50 Mbps
2 2 Multiplexing Multiplexing
Diversity Diversity 25 Mbps
2 1 Diversity Single 25 Mbps
1 2 Single Diversity 25 Mbps
1 1 Single Single 25 Mbps
Site A and B may be HBS or HSU.
C.3 Considerations for Changing Antenna
Parameters
Let:
max Available Tx Power denote the maximum Tx Power practically available from an ODU. (It
appears as Tx Power per Radio.)
maxRegEIRP denote the maximum EIRP available by regulation. It will be determined by
three factors:
• per band/regulation
• per channel bandwidth
• antenna gain
maxRegTxPower denote the maximum regulatory Tx Power for the equipment, also having
regard the above three points.
Then, the following relationship must be satisfied:
maxAvailableTxPower  min(maxRegEIRP ... (*)
– AntennaGain + CableLoss maxRegTxPower)
The Tx Power (per radio) indicates the power of each radio inside the ODU and is used for Link
Budget Calculations. The Tx Power (System) shows the total transmission power of the ODU
and is used to calculate the EIRP according to regulations.
The inequality (*) above is always satisfied by the system in accordance with the relevant
regulation.
The precise relationship between the items in inequality (*) is as follows:

• To see the relationship between Tx Power (radio) and Tx Power
(system), note that dBm = 10  log 10milliWatt so that if you
double the power in milliWatts (for two radios) then dBm will
increase by 10  log 102  3 .
• The Max EIRP level will be automatically set according to the
selected band and regulation.
• The EIRP level is the sum of the System Tx Power and the Antenna
Gain minus the Cable Loss.
• Required Tx Power (per radio) will be adjusted down to the lesser of the value entered
and maxAvailableTxPower
• Tx Power (system) is maxAvailableTxPower + 3 (for 2 radios)
• Max EIRP is maxRegEIRP.
• EIRP is maxAvailableTx Power + Antenna Gain ‐ Cable Loss

Appendix D: Regional Notice:
French Canadian
D.1 Procédures de sécurité
D.1.1 Généralités
Avant de manipuler du matériel connecté à des lignes électriques ou de télécommunications,
il est conseillé de se défaire de bijoux ou de tout autre objet métallique qui pourrait entrer en
contact avec les éléments sous tension.
D.1.2 Mise à la terre
Tous les produits RADWIN doivent être mis à la terre pendant l'usage courant. La mise à la
terre est assurée en reliant la fiche d'alimentation à une prise de courant avec une protection
de terre. En outre:
• La cosse de masse sur l'IDU‐C doit être constamment connectée à la protection de
terre, par un câble de diamètre de 18 AWG ou plus. Le matériel monté sur rack doit être
installé seulement sur des racks ou armoires reliés à la terre
• Une ODU doit mise à la terre par un câble de diamètre de 10 AWG ou plus
• Il ne doit pas y avoir de fusibles ou d'interrupteurs sur la connection à la terre
De plus:
• Il faut toujours connecter la terre en premier et la déconnecter en dernier
• Il ne faut jamais connecter les câbles de télécommunication à du matériel non à la terre
• Il faut s'assurer que tous les autres câbles sont déconnectés avant de déconnecter la
terre
D.1.3 Protection contre la foudre
L'utilisation de dispositifs de protection contre la foudre dépend des exigences
réglementaires et de l'utilisateur final. Toutes les unités extérieures RADWIN sont conçues
avec des circuits de limitation de surtension afin de minimiser les risques de dommages dus à
RADWIN 5000 Installation Guide Release 4.9 D‐1

la foudre. RADWIN conseille l'utilisation d'un dispositif de parafoudre supplémentaire afin de
protéger le matériel de coups de foudre proches.
Matériel supplémentaire requis
L'équipement requis pour l'installation du matériel est le suivant:
• Pince à sertir RJ‐45 (si un câble pré‐assemblé ODU/IDU n'est pas utilisé)
• Perceuse (pour le montage sur mur seulement)
• Câbles de terre IDU et ODU
• Clef 13 mm (½)
• Câble ODU ‐ IDU si non commandé (type extérieur, CAT‐5e, 4 paires torsadées, 24 AWG)
• Colliers de serrage
• Ordinateur portable avec Windows 2000 ou Windows XP.
D.1.4 Précautions de sécurité pendant le montage de ODU
Avant de connecter un câble à l'ODU, la borne protectrice de masse (visse) de l'ODU doit être
connectée à un conducteur externe protecteur ou à un pylône relié à la terre. Il ne doit pas y
avoir de fusibles ou d'interrupteurs sur la connection à la terre.
Seulement un personnel qualifié utilisant l'équipement de sécurité approprié doit pouvoir
monter sur le pylône d'antenne. De même, l'installation ou le démontage de ODU ou de
pylônes doit être effectuée seulement par des professionnels ayant suivi une formation.
 Pour monter l'ODU:
1. Vérifier que les supports de fixation de l'ODU sont correctement mis à la terre.
2. Monter l'unité ODU sur le pylône ou sur le mur; se référer à la Installation sur
pylône et mur au dessous.
3. Connecter la câble de terre au point de châssis sur l'ODU.
4. Relier le câble ODU‐IDU au connecteur ODU RJ‐45.
5. Visser les presses‐étoupe de câbles pour assurer le scellement hermétique des
unités ODU.
6. Attacher le câble au pylône ou aux supports en utilisant des colliers classés UV.
7. Répéter la procédure sur le site distant.
Ne pas se placer en face d'une ODU sous tension.
D.1.5 Connecter la terre à IDU‐C
Connecter un câble de terre de 18 AWG à la borne de masse de l'appareil. L'appareil doit être
constamment connecté à la terre.

• Les appareils sont prévus pour être installés par un personnel de ser‐
vice.
• Les appareils doivent être connectés à une prise de courant avec une
protection de terre.
• Le courant CC du IDU‐C doit être fourni par l'intermédiaire d'un disjonc‐
teur bipolaire et le diamètre du câble doit être de 14 mm avec un con‐
duit de 16 mm.
D.2 Installation sur pylône et mur
L' ODU ou l'O‐PoE peuvent être montés sur un pylône ou un mur.
D.2.1 Contenu du kit de montage ODU
Le kit de montage ODU comprend les pièces suivantes:
Figure D‐1: Contenu du kit de montage ODU

D.2.2 Montage sur un pylône
Figure D‐2: Montage sur un pylône (1) Figure D‐3: Montage sur un pylône (2)
D.2.3 Montage sur un mur
Figure D‐4: Montage sur un mur (1) Figure D‐5: Montage sur un mur (2)
D.2.4 Montage d'une antenne externe
L'antenne externe optionnelle peut être montée sur un pylône.
D.2.5 Contenu du kit de montage d'une antenne externe
Le kit de montage d'une antenne externe comprend les pièces suivantes
• Douze rondelles plates
• Huit rondelles élastiques
• Huit écrous hex

• Quatre boulons
• Un support en U
• Un support à pivotement
• Deux courroies de fixation en métal
 Pour installer une antenne externe sur un pylône:
1. Attacher le support en U à l'arrière de l'antenne en utilisant quatre rondelles plates,
quatre rondelles élastiques et quatre écrous hex.
2. Attacher le support à pivotement au support en U en utilisant huit rondelles plates,
quatre rondelles élastiques, quatre écrous hex et quatre boulons.
3. Passer les deux courroies de fixation par les fentes verticales dans le support à
pivotement.
4. Attacher l'antenne au pylône en utilisant les deux courroies de fixation .
Ajuster l'inclinaison nécessaire en utilisant l'échelle angulaire et serrer tous les boulons et
écrous à la position requise.

Appendix E: RF Exposure
The antennas used for the following transmitters must be installed so as to provide a
minimum separation distance from bystanders as specified in the following tables:
Table E‐1: Safety Distances for RADWIN 5000 HPMP FCC and IC Products
Frequency
Antenna gain Min. Safety
Band FCC ID IC ID
[dBi] Distance [cm]
[GHz]
5.8 Q3KRW5XMOD 5100A‐RW5XMOD 32 354

5.8 Q3KRW5XMOD 5100A‐RW5XMOD All sectors 20
5.3/5.4 Q3KRW5XMOD 5100A‐RW5XMOD All gains 20
4.9 Q3KRW5XMOD 5100A‐RW5XMOD 32, 29 96

4.9 Q3KRW5XMOD 5100A‐RW5XMOD 16, 15.5 31
2.4 Q3KRW24MOD 5100A‐RW24MOD 20 53
2.4 Q3KRW24MOD 5100A‐RW24MOD 17.5 43
2.4 Q3KRW24MOD 5100A‐RW24MOD 9, 8, 6.3 20
RADWIN 5000 Installation Guide Release 4.9 E‐1

Table E‐2: Safety Distances for RADWIN 5000 HPMP ETSI Products
Min. Safety
Frequency Band Antenna gain
Distance
[GHz] [dBi]
[cm]
5.8/5.3/5.4/2.4 All gains 20
RADWIN 5000 Installation Guide Release 4.9 E‐2

Appendix C: Revision History

Table C‐1: Revision History: RADWIN 5000 HPMP Installation Guide
Cat.No. Date Description
DQ0193770/0.1 Feb, • Initial release
System Release 4.9 2017

Regulatory Compliance
General Note
This system has achieved Type Approval in various countries around the world. This means
that the system has been tested against various local technical regulations and found to
comply. The frequency bands in which the system operates may be “unlicensed” and in these
bands, the system can be used provided it does not cause interference.
FCC ‐ Compliance
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
It is the responsibility of the installer to ensure that when using the
outdoor antenna kits in the United States (or where FCC rules apply), only
those antennas certified with the product are used. The use of any
antenna other than those certified with the product is expressly forbidden
by FCC rules 47 CFR part 15.204.
It is the responsibility of the installer to ensure that when configuring the
radio in the United States (or where FCC rules apply), the Tx power is set
according to the values for which the product is certified. The use of Tx
power values other than those, for which the product is certified, is
expressly forbidden by FCC rules 47 CFR part 15.204.
Indoor Units comply with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) These devices may not cause harmful interference.
RADWIN 5000 Installation Guide Release 4.9 i
(2) These devices must accept any interference received, including interference that may
cause undesired operation.
The RADWIN 5000 JET has 3.65GHz FCC central frequency limitations as follows:
• For the 20MHz channel, frequencies are limited to 3661‐3689 MHz
• For the 40MHz channel, frequency is limited to 3675MHz
The responsibility for staying within the following frequency limits falls on the operator (or, if
professionally installed, on the installer).
Outdoor units and antennas should be installed ONLY by experienced
installation professionals who are familiar with local building and safety
codes and, wherever applicable, are licensed by the appropriate
government regulatory authorities. Failure to do so may void the product
warranty and may expose the end user or the service provider to legal and
financial liabilities. Resellers or distributors of this equipment are not
liable for injury, damage or violation of regulations associated with the
installation of outdoor units or antennas. The installer should configure
the output power level of antennas according to country regulations and
antenna type.
• Where Outdoor units are configurable by software to Tx power val‐
ues other than those for which the product is certified, it is the
responsibility of the Professional Installer to restrict the Tx power to
the certified limits.
• This product was tested with special accessories ‐ indoor unit (IDU or
PoE), FTP CAT‐5e shielded cable with sealing gasket, 10 AWG ground‐
ing cable ‐ which must be used with the unit to insure compliance.
Canadian Emission Requirements for Indoor Units
This Class B digital apparatus complies with Canadian ICES‐003.
Cet appareil numẻrique de la classe B est conforme ả la norme NMB‐003 du Canada.
China MII
Operation of the equipment is only allowed under China MII 5.8GHz band regulation
configuration with EIRP limited to 33 dBm (2 Watt).
India WPC
Operation of the equipment is only allowed under India WPC GSR‐38 for 5.8GHz band
regulation configuration.
RADWIN 5000 Installation Guide Release 4.9 ii
Brazil
The equipment will operate only in the frequency bands 5470 ‐ 5725 MHz and 5725 ‐ 5850
MHz. The software version to be sold in Brazil with blocking is from version 4.6.
The power supplies presented in this user manual are not sold with this product.
O equipamento irá operar apenas nas faixas de frequências 5470 ‐ 5725 MHz e 5725 ‐ 5850
MHz. A versão do software a ser comercializado no Brasil com bloqueio é a partir da versão
4.6.
As fontes de alimentação apresentadas neste manual não serão comercizliadas junto com
este produto.
Unregulated
In countries where the radio is not regulated the equipment can be operated in any
regulation configuration, best results will be obtained using Universal regulation
configuration.
Safety Practices
Applicable requirements of National Electrical Code (NEC), NFPA 70; and the National
Electrical Safety Code, ANSI/IEEE C2, must be considered during installation.
NOTES:
1. A Primary Protector is not required to protect the exposed wiring as long as the exposed
wiring length is limited to less than or equal to 140 feet, and instructions are provided to
avoid exposure of wiring to accidental contact with lightning and power conductors in
accordance with NEC Sections 725‐54 (c) and 800‐30.
In all other cases, an appropriate Listed Primary Protector must be provided. Refer to Articles
800 and 810 of the NEC for details.
2. For protection of ODU against direct lightning strikes, appropriate requirements of NFPA
780 should be considered in addition to NEC.
3. For Canada, appropriate requirements of the CEC 22.1 including Section 60 and additional
requirements of CAN/CSA‐B72 must be considered as applicable.
RADWIN 5000 Installation Guide Release 4.9 iii

RADWIN 5000 HPMP
Installation Guide
Cat.No. DQ0193780
This manual contains information that is proprietary to RADWIN Ltd (RADWIN hereafter). No
part of this publication may be reproduced in any form whatsoever without prior written
approval by RADWIN.
Right, title and interest, all information, copyrights, patents, know‐how, trade secrets and
other intellectual property or other proprietary rights relating to this manual and to the
RADWIN products and any software components contained therein are proprietary products
of RADWIN protected under international copyright law and shall be and remain solely with
RADWIN.
The RADWIN name is a registered trademark of RADWIN. No right, license, or interest to such
trademark is granted hereunder, and you agree that no such right, license, or interest shall be
asserted by you with respect to such trademark.
You shall not copy, reverse compile or reverse assemble all or any portion of the Installation
Guide or any other RADWIN documentation or products. You are prohibited from, and shall
not, directly or indirectly, develop, market, distribute, license, or sell any product that
supports substantially similar functionality based or derived in any way from RADWIN
products.Your undertaking in this paragraph shall survive the termination of this Agreement.
This Agreement is effective upon your opening of a RADWIN product package and shall
continue until terminated. RADWIN may terminate this Agreement upon the breach by you of
any term thereof. Upon such termination by RADWIN, you agree to return to RADWIN any
RADWIN products and documentation and all copies and portions thereof.
For further information contact RADWIN at one of the addresses under Worldwide Contacts
below or contact your local distributor.
Disclaimer
The parameters quoted in this document must be specifically confirmed in writing before
they become applicable to any particular order or contract. RADWIN reserves the right to
make alterations or amendments to the detail specification at its discretion. The publication
of information in this document does not imply freedom from patent or other rights of
RADWIN, or others.
Trademarks
WinLink 1000, RADWIN 2000, RADWIN 5000, RADWIN 6000 and RADWIN 600 are
trademarks of RADWIN Ltd
Windows 2000, XP Pro, Vista, Windows 7 and Internet Explorer are trademarks of Microsoft
Inc.
Mozilla and Firefox are trademarks of the Mozilla Foundation.
RADWIN 5000 Installation Guide Release 4.9 iv
Other product names are trademarks of their respective manufacturers.
RADWIN 5000 Installation Guide Release 4.9 v
RADWIN Worldwide Offices
Corporate and EMEA Regional Headquarters
Corporate and EMEA Headquarters North America Regional
27 Habarzel Street Headquarters
Tel Aviv,6971039
Israel 900 Corporate Drive
Tel: +972.3.766.2900 Mahwah, NJ, 07430
Fax: +972.3.766.2902 USA
Tel: +1-877-RADWIN US
Email: sales@radwin.com (+1-877 723-9468)
Tel: +1-201-252-4224
Fax: +1-201-621-8911
Email: salesna@radwin.com
Customer Support - North America:
Hours: 9 am - 6 pm EST (Mon - Fri)
Email: supportusa@radwin.com
RADWIN Regional Offices
RADWIN Brazil RADWIN Mexico
Av. Chucri Zaidan, 920 – 9º Quinto #20 Col El Centinela
São Paulo, 04583-904 Mexico, DF, O4450
Brazil Mexico
Tel: +55.11.3048-4110 Tel: +52 (55) 5689 8970
Email: salesbr@radwin.com Email: salesmx@radwin.com
RADWIN Peru RADWIN India
Av. Antares 213 E-13,B-1 Extn., Mohan Co-operative Industrial Estate
Lima, 33 New Delhi, 110 044
Peru India
Tel: +511.6285105 Tel: +91-11-40539178
Fax: +511-990304095 Email: salesin@radwin.com
Email: salespe@radwin.com
RADWIN Philippines RADWIN South Africa
5 Bur Bank St. P.O. Box 3554, Rivonia
Laguna, Belair, Santa Rosa Johannesburg ,2128
Laguna Philippines South Africa
Tel: +63 928 7668230 Tel: +27 (0)82 551 5600
Email: salesph@radwin.com Email: sales@radwin.com
RADWIN Italy and Spain RADWIN Central America
Piazza Arenella 7/H Calle La CaÃ±ada # 108-E
Napoli ,80128 Jardines de la Hacienda
Italy Ciudad Merliot El Salvador
Tel:+390815564116 Tel: +503 2278-5628
Fax: +39335433620 Email: sales@radwin.com
Email: salesit@radwin.com
RADWIN 5000 Installation Guide Release 4.9 vi
RADWIN Worldwide Offices (Continued)
RADWIN South East Asia
All Season Mansion
87/38 Wireless Road Lumpinee
Bangkok ,10330
Thailand
Tel: +66811707503
Email: sales@radwin.com
RADWIN 5000 Installation Guide Release 4.9 vii

RADWIN 5000 Installation Guide Release 4.9 viii

Installation Guide: RADWIN 5000

Uploaded by

Copyright:

Available Formats

Installation Guide: RADWIN 5000

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation Guide: RADWIN 5000

Uploaded by

Copyright:

Available Formats

INSTALLATION GUIDE

RADWIN 5000 Installation Guide Release 4.9 1‐1

RADWIN 5000 Installation Guide Release 4.9 1‐2

RADWIN 5000 Installation Guide Release 4.9 1‐3

RADWIN 5000 Installation Guide Release 4.9 1‐4

RADWIN 5000 Installation Guide Release 4.9 1‐5

RADWIN 5000 Installation Guide Release 4.9 1‐6

RADWIN 5000 Installation Guide Release 4.9 1‐7

1. Prepare Laptop page 2‐2

2. Connect Laptop to Radio Unit page 2‐2

3. Update Connectivity Parameters of Radio Unit page 2‐4

4. Check items to be installed page 2‐6

6. Install Standard Mounting Kit page 2‐7

7. Install Mounting Kit for the SU PRO/AIR Radio Unit page 2‐13

8. Mounting a Unit with the Standard Mounting Kit page 2‐16

9. Ground Radio Unit page 2‐19

10. Mounting the SU PRO/AIR Radio Unit page 2‐22

11. Mounting the Lightning Protection Units page 2‐24

12. Connect External Antenna (if applicable) page 2‐27

13. Waterproofing page 2‐27

14. Connect Radio page 2‐28

15. Check Connectivity to Radio page 2‐31

16. Activate Base Station page 2‐31

17. Align Subscriber Unit page 2‐31

RADWIN 5000 Installation Guide Release 4.9 2‐1

RADWIN 5000 Installation Guide Release 4.9 2‐2

RADWIN 5000 Installation Guide Release 4.9 2‐3

RADWIN 5000 Installation Guide Release 4.9 2‐4

RADWIN 5000 Installation Guide Release 4.9 2‐5

RADWIN 5000 Installation Guide Release 4.9 2‐6

RADWIN 5000 Installation Guide Release 4.9 2‐7

Vertical Pole page 2‐8

Wall page 2‐13

Thin Pole Dia. 3/4 ‐1 1/2 page 2‐9

Medium Pole Dia. 2 ‐ 3 page 2‐9

RADWIN 5000 Installation Guide Release 4.9 2‐8

RADWIN 5000 Installation Guide Release 4.9 2‐9

RADWIN 5000 Installation Guide Release 4.9 2‐10

RADWIN 5000 Installation Guide Release 4.9 2‐11

RADWIN 5000 Installation Guide Release 4.9 2‐12

RADWIN 5000 Installation Guide Release 4.9 2‐13

RADWIN 5000 Installation Guide Release 4.9 2‐14

RADWIN 5000 Installation Guide Release 4.9 2‐15

RADWIN 5000 Installation Guide Release 4.9 2‐16

For JET radio units, mount as shown in Figure 2‐24 and Figure 2‐25:

RADWIN 5000 Installation Guide Release 4.9 2‐17

RADWIN 5000 Installation Guide Release 4.9 2‐18

RADWIN 5000 Installation Guide Release 4.9 2‐19

RADWIN 5000 Installation Guide Release 4.9 2‐20

RADWIN 5000 Installation Guide Release 4.9 2‐21

RADWIN 5000 Installation Guide Release 4.9 2‐22

RADWIN 5000 Installation Guide Release 4.9 2‐23

RADWIN 5000 Installation Guide Release 4.9 2‐24

RADWIN 5000 Installation Guide Release 4.9 2‐25

RADWIN 5000 Installation Guide Release 4.9 2‐26

RADWIN 5000 Installation Guide Release 4.9 2‐27

RADWIN 5000 Installation Guide Release 4.9 2‐28

RADWIN 5000 Installation Guide Release 4.9 2‐29

RADWIN 5000 Installation Guide Release 4.9 2‐30