TW 160PH WOOD CHIPPER

INSTRUCTION MANUAL

timberwolf-uk.com
 © Copyright Entec Industries Ltd 2015

The content of this publication may not be copied, reproduced, republished, posted, broadcast, transmitted
or used in any way in any medium without the written permission of Entec Industries Ltd.
 CONTENTS TW 160PH
Section Page No.
INTRODUCTION 1
PURPOSE OF MACHINE 2
MACHINE DIMENSIONS & SPECIFICATIONS 2
PARTS LOCATION DIAGRAMS 3
SAFE WORKING 5
Operator’s Personal Protective Equipment Required 5
Basic Woodchipping Safety 5
General Safety Matters - Do’s and Dont’s 6
Noise Test 7
OPERATING INSTRUCTIONS 8
Safe Transportation 8
Hitching onto the Tow Ball 8
Unhitching the Chipper 8
Stabilising the Chipper 8
Delivery 9
Operator’s Personal Protective Equipment Required 9
Manual Controls 9
Auto Controls 10
Emergency Stopping 10
Engine Controls 10
Blade Wear 10
Hydraulic Oil Lever Indicator 10
Petrol Tank Indicator 10
Daily Checks Before Starting 11
Before Using the Chipper 11
Starting the Engine 11
Stopping the Engine 11
Starting to Chip 12
Chipping 12
Blockages 12
Discharge Controls 12
SERVICE INSTRUCTIONS 13
Service Schedule 14
Safe Maintenance 15
Safe Lifting of the Chipper 15
Spares 15
Battery Removal and Maintenance 15
Check Fittings 15
Copper Ease Safety Information 16
Battery Safety Information 17
Change Blades 18
Tension Belts 19
Change Hydraulic Oil and Filter 19
Grease the Roller Spline and Rotor Bearings 20
Grease the Roller Box Slides 20
Grease the Discharge Flange 20
Engine Servicing 20
Check Hoses 20
WARRANTY STATEMENT 21
EC DECLARATION OF CONFORMITY CERTIFICATE 22
IDENTIFICATION PLATES 23
DECALS 24
ELECTRICAL DETAIL 26
CIRCUIT DIAGRAM 27
HYDRAULIC LAYOUT 29
V- BELT TENSIONING TABLE 30
WARRANTY SERVICE CHECK RECORD 31
SERVICE RECORD 32
PARTS LISTS 33

C190-0013 11.04.2019
 INTRODUCTION 1 / 51
TW 160PH

Thank you for choosing Timberwolf. Timberwolf chippers are designed to give safe and dependable service if operated
according to the instructions.

IMPORTANT HEALTH AND SAFETY INFORMATION

Before using your new chipper, please take time to read this manual. Failure to do so could result in:
- personal injury
- equipment damage
- damage to property
- 3rd party injuries
This manual covers the operation and maintenance of the Timberwolf TW 160PH. All information in this manual is
based on the latest product information available at the time of purchase.
All the information you need to operate the machine safely and effectively is contained within pages 2 to 12. Ensure
that all operators are properly trained for operating this machine, especially in safe working practices.
Timberwolf's policy of regularly reviewing and improving their products may involve major or minor changes to the
chippers or their accessories. Timberwolf reserves the right to make changes at any time without notice and without
incurring any obligation.
Due to improvements in design and performance during production there may be, in some cases, minor discrepancies
between the actual chipper and the text in this manual.
The manual should be considered an important part of the machine and should remain with it if the machine is
resold.

CAUTION or WARNING
BE AWARE OF THIS SYMBOL
AND WHERE SHOWN,
CAREFULLY FOLLOW THE
INSTRUCTIONS.

THIS SYMBOL INDICATES

IMPORTANT SAFETY
MESSAGES IN THIS MANUAL.
WHEN YOU SEE THIS SYMBOL,
BE ALERT TO THE POSSIBILITY
OF INJURY TO YOURSELF OR
OTHERS AND CAREFULLY READ
THE MESSAGE THAT FOLLOWS.

ALWAYS FOLLOW SAFE

OPERATING AND
MAINTENANCE PRACTICES

C190-0013 11.04.2019
 2 / 51
TW 160PH

THE TIMBERWOLF TW 160PH

Designed to chip solid wood material up to 150mm in diameter and capable of

chipping up to 3.5 tonnes of brushwood per hour.

DIMENSIONS
2108 mm (1248 mm with discharge removed)

Serial No. Location

The serial number can
be found on the
identification plate
located on the chassis
beam.

m
66m
12

3475mm (2935mm with feed tray folded)

TIMBERWOLF TW 160PH SPECIFICATION

Engine type: Honda v‐twin petrol Max. diameter material: 152mm (6”)
Maximum power: 16.4kW (22hp) Fuel capacity: 18 litres
Cooling method: Air cooled Hydraulic oil capacity: 15 litres
Overall weight: 608kg Material processing capacity: 3.5 tonnes/hr
Starting method: Electric Fuel type: Unleaded petrol
Roller feed: Twin hydraulic motor

C190-0013 11.04.2019
 PARTS LOCATOR 3 / 51
TW 160PH

EMERGENCY
FUNNEL STOP

SAFETY BAR MANUAL

CANNISTER
CONTROL BOX
DISCHARGE
(Both sides)
BUCKET

DISCHARGE
TUBE

ROLLER BOX
COVER
DISCHARGE
CLAMP NUTS

LIFTING EYE

BELT GUARD
REFLECTOR ENGINE

FEED
TRAY

LIGHT BOARD

WHEEL CHOCK ACCESS

HATCH

REFLECTORS ROTOR HOUSING

C190-0013 11.04.2019
 PARTS LOCATOR 4 / 51
TW 160PH

ROLLER BOX FAN

SECTION (x4)

DIRECTIONAL ROTOR
CONTROL ROTOR DRIVE
HYDRAULIC VALVE PULLEY
CUTTER
OIL FILTER BLADE (x2)
HYDRAULIC
HYDRAULIC PUMP
OIL TANK

BATTERY HYDRAULIC
PUMP BELT
ADJUSTER

JOCKEY
WHEEL
ASSEMBLY

PROP
STAND

FUEL TANK

GREASING
PANEL

BELT TENSION ENGINE DRIVE ENGINE TOW HEAD

ADJUSTER PULLEY PULLEY SHAFT

C190-0013 11.04.2019
 SAFE WORKING 5 / 51
TW 160PH

OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT (PPE)

• Chainsaw safety helmet (EN 397) fitted with mesh visor (EN 1731) and ear defenders (EN 352).
• Work gloves with elasticated wrist.
• Steel toe cap safety boots (EN 345-1).
• Close fitting heavy-duty non-snag clothing. High-visibility clothing (EN 471) if risk assessment identifies the need.
• Face mask if appropriate.
• DO NOT wear rings, bracelets, watches, jewellery or any other items that could be caught in the material and draw you
into the chipper.

WARNING
THE CHIPPER WILL FEED MATERIAL THROUGH ON ITS OWN. TO DO THIS, IT
RELIES ON SHARP BLADES BOTH ON THE FEED ROLLERS AND THE CHIPPER
ROTOR. TO KEEP THE BLADES SHARP, ONLY FEED THE MACHINE WITH
CLEAN BRUSHWOOD. DO NOT PUT MUDDY/DIRTY WOOD, ROOTS, POTTED
PLANTS, BRICKS, STONES OR METAL INTO THE CHIPPER.

BASIC WOODCHIPPING SAFETY

The operator should be aware of the following points:
• Maintain a safety exclusion zone around the chipper of at least 10 metres for the general public or employees without
adequate protection. Use hazard tape to identify this working area and keep it clear from debris build up. Chips
should be ejected away from any area the general public have access to.
• Hazardous material - Some species of trees and bushes are poisonous. The chipping action can produce vapour, spray
and dust that can irritate the skin. This may lead to respiratory problems or even cause serious poisoning. Check the
material to be chipped before you start. Avoid confined spaces and use a face mask if necessary.
• Be aware when the chipper is processing material that is an awkward shape. The material can move from side to side
in the funnel with great force. If the material extends beyond the funnel, the brash may push you to one side causing
danger. Badly twisted brash should be trimmed before being chipped to avoid thrashing in the feed funnel.
• Be aware that the chipper can eject chips out of the feed funnel with considerable force. Always wear full head and
face protection.
• Always work on the side of the machine furthest from any local danger, e.g. not road side.
• Never leave the chipper unattended when running. Machines must be supervised at all times when in use.
• In the event of an accident, stop the machine, remove the key and call the emergency services immediately.

C190-0013 11.04.2019
 SAFE WORKING 6 / 51
TW 160PH
GENERAL SAFETY MATTERS
• Always stop the chipper engine before making any adjustments, refuelling or cleaning.
• Always check the rotor has stopped rotating and remove the chipper ignition key before maintenance of any kind, or
whenever the machine is to be left unattended. If in doubt, look through the in-feed funnel to see if rotor is still
moving.
• Always check the machine is well supported and cannot move. If working on an incline, position on solid ground,

ü
across the slope.
• Always operate the chipper with the engine set to maximum speed when chipping.
• Always check (visually) for fluid leaks. If found, resolve the leak before operating the chipper.
• Always take regular breaks. Wearing personal protective equipment for long periods can be tiring
and hot.
• Always keep hands, feet and clothing out of feed opening, discharge and moving parts.
• Always use a push stick to push in short pieces. Under no circumstances should you reach into
the funnel.
• Always keep the operating area clear of people, animals and children.
• Always keep the operating area clear from debris build up.
• Always keep clear of the chip discharge tube. Foreign objects may be ejected with great force.
• Always ensure protective guarding is in place before commencing work. Failure to do so may
result in personal injury or loss of life.
• Always operate the chipper in a well ventilated area - exhaust fumes are dangerous.
• Ensure a fire extinguisher is available on site.
• Ensure a personal first aid kit and hand cleaning materials are available (e.g. waterless skin cleanser).
• Always cover ignition switch with plug provided when towing or jet wash cleaning.

DO NOT ALLOW THE FOLLOWING TO ENTER THE MACHINE, AS DAMAGE IS LIKELY

CLOTH STONES METAL GLASS RUBBER PLASTIC

BRICKS STRING ROOTS BEDDING

PLANTS

• Do not operate chipper unless available light is sufficient to see clearly.

• Do not use or attempt to start the chipper without the feed funnel, guards and discharge unit securely in place.
• Do not stand directly in front of the feed funnel when using the chipper. Stand to one side.
• Do not smoke when refuelling.
• Do not let anyone who has not received instruction operate the machine.
• Do not climb on the machine at any time.
• Do not handle material that is partially engaged in the machine.
• Do not touch any exposed wiring while the machine is running.
• Do not use the chipper inside buildings.

C190-0013 11.04.2019
 SAFE WORKING 7 / 51
TW 160PH

NOISE TEST

MACHINE: TW 160PH
NOTES: TESTED CHIPPING 120MM CORSICAN PINE 1.5M IN LENGTH

Noise levels above 80dB (A) will be experienced at the working position. Wear ear protection at all times to
prevent possible damage to hearing. All persons within a 4 metre radius must also wear good quality ear
protection.

86
.9d
B(
A)
C

al
cu
lat
ed
100.53 dB
95.37 dB

94.47 dB 92.87 dB
B(A) Calculated

90.87 dB
91.10 dB
86.9d

R= 4 metres

92.87dB 91.30 dB
94.47 dB

ed
lat
lcu
) Ca
B(A
.9d
86

R= 10 metres

Guaranteed Sound Power: 117dB (A)

As required by Annex III of Directive 2000/14/EC “Noise Emission in the environment by equipment for use outdoors”.

C190-0013 11.04.2019
 OPERATING INSTRUCTIONS 8 / 51
TW 160PH
SAFE TRANSPORTATION
WARNING
• When towing a chipper the maximum speed limit is 60 DO NOT RIDE ON THE
mph. CHIPPER WHEN IT IS BEING
• On rough or bumpy road surfaces reduce speed TOWED.
accordingly to protect your machine from unnecessary
vibration. • Always check the discharge is tight before moving.
• When towing off road be aware of objects that may • Keep tyre pressures inflated to 2.2 bar or 32 psi.
catch the chipper undergear. • Check wheel nuts are tightened to 90nm or 65 lbs ft.
• When towing off road ensure inclination is not • Clear loose chippings and debris from the machine
excessive. before departing.
• Avoid excessively pot holed ground. • Ensure feed funnel is closed and the catch is properly
• When reversing the chipper the short wheel base will engaged before departing.
react quickly to steering.

HITCHING ONTO THE TOW BALL

• Check ball head is well greased. the ball hitch. If it doesn't, repeat previous 2 steps.
• Wind jockey wheel assembly anticlockwise until the • Wind jockey wheel up until fully retracted and the
tow head is above the height of the ball hitch on the jockey wheel frame is seated in its notch on the stem.
vehicle. The chipper weight should be fully on the vehicle.
• Reverse vehicle so the ball hitch is directly below the • Release jockey wheel clamp and slide the jockey
tow head. wheel assembly fully up.
• Attach breakaway cable to a strong point on the • Tighten clamp on jockey wheel assembly.
vehicle, not the ball hitch. • Connect electrical plug to socket on rear of towing
• Grasp handle on tow head and push back catch with vehicle and check operation of all the trailer and
thumb. vehicle lights.
• Wind jockey wheel assembly clockwise, to lower the • Check the engine ignition switch is covered with the
tow head onto the ball hitch. plug provided.
• Release handle and continue to wind jockey wheel • The chipper is now properly attached to the vehicle.
clockwise. The tow head should snap into place on
UNHITCHING THE CHIPPER
• Ensure the chipper will not roll away after being • Wind the jockey wheel assembly anticlockwise until it
disconnected from the vehicle. Use the chocks starts to take the weight of the chipper.
provided if in doubt. • Grasp the handle and release the catch with your
• Disconnect the electrical cable from the vehicle thumb.
socket. • Continue to wind the jockey wheel anticlockwise. This
• Release breakaway cable. should lift the tow head clear of the ball hitch.
• Release the jockey wheel assembly clamp. • Drive the vehicle clear of the chipper.
• Lower the jockey wheel assembly fully. • Wind the jockey wheel assembly to a suitable point
• Retighten the jockey wheel assembly clamp. where the chipper is level.
• The chipper is now fully detached from the vehicle.
STABILISING THE CHIPPER
When hitched to a vehicle the prop stand and When the chipper is unhitched it should be secured
jockey wheel should be stored in the towing before starting work by using the wheel chocks and
position (a). lowering the prop stand and jockey wheel (b).
(a) (b)

C190-0013 11.04.2019
 OPERATING INSTRUCTIONS 9 / 51
TW 160PH
DELIVERY
All Timberwolf TW 160 machines have a full pre - delivery inspection before leaving the factory and are ready to use.
Read and understand this instruction manual before attempting to operate the chipper. In particular, read pages 5-7
which contain important health and safety information and advice.

OPERATOR’S PERSONAL PROTECTIVE EQUIPMENT REQUIRED

• Chainsaw safety helmet fitted with visor and • Close - fitting heavy-duty non-snag clothing.
recommended ear defenders to an appropriate • Safety footwear.
specification.
• Face mask (if appropriate).
• Heavy-duty gloves with elasticated wrist area.
See page 5 for more detailed information.
MANUAL CONTROLS
Roller control boxes- a control box is located on either side of the feed funnel. Their function is to control the feed roller
whilst processing material. They do not control the main rotor.
RED SAFETY BAR = This is the large red bar that surrounds the feed tray and side of the feed funnel. The bar is spring
loaded and connected to a switch that will interrupt the power to the rollers. The switch is designed so that it only
activates if the bar is pushed to the limit of its travel. The rollers stop instantly, but can be made to turn again by
pressing either the GREEN FEED or BLUE REVERSE control buttons.
RED SAFETY BAR TEST
To ensure the safety bar is always operational it must be activated once before each work session. The rollers will
not function until the bar is activated. This procedure must be repeated each time the ignition is switched off.
GREEN BUTTON = forward feed - Push the button once - this activates
the rollers and will allow you to start chipping (if the rotor speed is WARNING
high enough). DO NOT REMOVE, JAM,
DISABLE, BYPASS, OVERRIDE
BLUE BUTTON = reverse feed - allows you to back material out of the OR OTHERWISE IMPEDE THE
rollers. The rollers will only turn in reverse as long as you keep EFFECTIVENESS OF THE RED
pressing the button. SAFETY BAR.

CONTROL PANEL DIAGRAM BLUE REVERSE GREEN FORWARD

FEED PANEL FEED PANEL
RED STOP FEED -
EMERGENCY STOP BUTTON

RED SAFETY BAR

(Both sides of feed funnel)

Do not rely on the red bar to keep the rollers stationary if it is necessary to clear or touch the rollers. Always switch
off the machine and remove ignition key before approaching the rollers.

C190-0013 11.04.2019
 OPERATING INSTRUCTIONS 10 / 51
TW 160PH

AUTO CONTROLS
The no stress unit controls the feed rate of the material going into the chipping chamber. If the rotor speed is
below the predetermined level, the no stress unit will not allow the feed rollers to work in either forward or
reverse, until the rotor speed rises above the predetermined level. At this point, the feed rollers will start turning
without warning.
EMERGENCY STOPPING
There are two methods of stopping the TW 160PH chipper in the event of an emergency.
STOPPING THE ROLLERS
-Activating the red safety bar will stop the rollers immediately. To restart the rollers, just push the green forward
button or blue reverse button.
STOPPING THE ROLLERS & ENGINE
Pushing the red Emergency stop button positioned on top of the funnel kills all power to
both the engine and the rollers, bringing the machine to a complete stop. It overrides all
buttons and bars and will not allow the chipper to function until it has been reset. To
reset, pull out button until it returns to its original position, turn the ignition key back to
the off position, before restarting the machine.

ENGINE CONTROLS FAST

This label indicates the speed setting of the

chipper. With the throttle lever in the fast
position (hare) the machine is ready to chip. SLOW

When the machine is not in use for short

periods of time move the lever to the idle
position (tortoise) or turn off completely.

BLADE WEAR
The most important part of using a wood chipper is keeping the cutter blades sharp. Timberwolf chipper
blades are hollow ground to an angle of 40 degrees. When performing daily blade checks ensure blade edge
is sharp and free from chips, if there is any evidence of damage, or the edge is “dull” change the blade(s). The
TW 160PH is fitted with 2 blades 109mm long. They are 100mm wide when new. A new blade should chip
for up to 25 hours before it requires sharpening. This figure will be drastically reduced by feeding the
machine with stony, sandy or muddy material.
As the blade becomes blunt, performance is reduced. With increased stress and load on the machine the
chips will become more irregular and stringy. At this point the blade should be sent to a reputable blade
sharpening company. The blade can be sharpened several times in its life. A wear mark indicates the safe
limit of blade wear. Replace when this line is exceeded.
The machine is also fitted with a static blade (anvil). It is important that the anvil is in good condition to allow
the cutting blades to function efficiently. Performance will be poor even with sharp cutter blades if the anvil
is worn.
HYDRAULIC OIL LEVEL INDICATOR
The oil level will be visible through the tank wall. It should be within the upper
and lower level marks.

PETROL TANK INDICATOR

The fuel level may be inspected by removing the fuel filler cap and looking into
the tank.

C190-0013 11.04.2019
 OPERATING INSTRUCTIONS 11 / 51
TW 160PH

DAILY CHECKS BEFORE STARTING

• Locate the machine on firm level ground. • Check the feed funnel to ensure no objects are
• Check machine is well supported and cannot inside.
move. • Check feed tray is in up position - to prevent
• Check jack stand is lowered and secure. people reaching rollers.
• Check all guards are fitted and secure. • Check controls as described below.
• Check the discharge unit is in place and fastened • Check (visually) for fluid leaks.
securely. • Check fuel and hydraulic oil levels.
• Check discharge tube is pointing in a safe For parts location see diagrams on pages 3 & 4.
direction.

BEFORE USING THE CHIPPER

It is essential to carry out the following tests to check safety equipment - this sequence of tests will only take a few
seconds to carry out. We recommend that these tests are carried out daily. Observing the function as described will
confirm that the safety circuits are working correctly. This is also a good opportunity to remind all operators of the
control and emergency stop systems.

WITH THE ENGINE RUNNING AT FULL SPEED

PRESS THE RED BAR PRESS THE GREEN PANEL PRESS THE RED BAR PRESS THE BLUE PANEL
TO POWER THE
CONTROL SYSTEM THE ROLLERS THE ROLLERS THE ROLLERS SHOULD TURN
SHOULD RUN BACKWARDS ONLY WHILE THE PANEL
SHOULD STOP IS PRESSED

PRESS THE GREEN PRESS THE EMERGENCY PRESS THE BLUE PULL TO RESET
PANEL AGAIN RED BUTTON PANEL THE RED BUTTON
THE ROLLERS THE ROLLERS THE ROLLERS SHOULD THE MACHINE IS
SHOULD RUN SHOULD STOP NOT TURN READY TO USE

STARTING THE ENGINE

THROTTLE FOR A COLD ENGINE:
LEVER
• Place the throttle control at 1/3 throttle and pull the choke out.
• Insert ignition key into starter switch.
• Turn the key to start the engine. Release the key as soon as the
engine starts.
• Gradually return the choke to the off position as the engine starts
and warms up. Allow the engine to warm up for at least one minute
before chipping.
FOR A WARM ENGINE:
• Follow the instructions for a ‘cold engine’ but return the choke to the
off position as soon as the engine starts.
STARTER
CHOKE SWITCH
If engine fails to start after 10 seconds leave for 1 minute and try again.
STOPPING THE ENGINE
• Set engine to idle position. • Switch off and remove ignition key.
• Allow to run for at least one full minute. For more detailed information refer to the Engine Owner’s
Manual

C190-0013 11.04.2019
 OPERATING INSTRUCTIONS 12 / 51
TW 160PH
STARTING TO CHIP
DO NOT USE OR ATTEMPT TO START THE CHIPPER WITHOUT THE
PROTECTIVE GUARDING AND DISCHARGE UNIT SECURELY IN
WARNING PLACE. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR
LOSS OF LIFE.
• Check that the chipper is running smoothly. • Press the green control panel. The rollers will
• Release the catches on the feed tray and lower. commence turning.
Pull to release the red stop button. • Stand to one side of the feed funnel.
• Perform the “before using the chipper” tests • Proceed to feed material into the feed funnel.
(see page 11).
CHIPPING
Wood up to the recommended diameter can be fed into the feed funnel. Put the butt end in first and engage
it with the feed rollers. The hydraulic feed rollers will pull the branch into the machine quite quickly. Large
diameter material will have its feed rate automatically controlled by the no stress unit.
Sometimes a piece of wood that is a particularly awkward shape is too strong for the feed rollers to break. This
will cause the top roller to either bounce up and down on the wood, or both rollers to stall. If this occurs, press
the BLUE REVERSE panel until the material has been released. Pull the material out of the feed funnel and trim
it so the chipper can handle it.
Both feed rollers should always turn at the same speed. If one or both rollers stop or suddenly slow down it may
be that a piece of wood has become stuck behind one of the rollers. If this occurs, press the BLUE REVERSE
panel and hold for 2 seconds - then repress GREEN FEED panel. This should enable the rollers to free the
offending piece of material and continue rotating at the correct speed. If the rollers continue to stall in the
'forward feed' or 'reverse feed' position push the RED STOP BUTTON, turn the engine off, remove the ignition
key and investigate.
BLOCKAGES
Always be aware that what you are putting into the chipper must come out. If the chips stop coming out of the
discharge tube but the chipper is taking material in - STOP IMMEDIATELY. Continuing to feed material into a
blocked machine may cause damage and will make it difficult to clear.
If the chipper becomes blocked, proceed as follows:
• Stop the engine and remove the ignition keys.
• Remove the discharge tube. Check that it is clear.
• Wearing gloves, reach into the rotor housing and scoop out the majority of the debris causing the blockage.

DO NOT REACH INTO THE ROTOR HOUSING WITH

UNPROTECTED HANDS. THERE ARE SHARP BLADES AND ANY
WARNING SMALL MOVEMENT OF THE ROTOR MAY CAUSE SERIOUS
INJURY.
• Replace the discharge tube.
• Restart the engine and increase to full speed.
• Allow machine time to clear excess chips still remaining in rotor housing before you continue feeding
brushwood. Feed in a small piece of wood while watching to make sure that it comes out of the
discharge. If this does not clear it, repeat the process and carefully inspect the discharge tube to find any
obstruction.
NOTE: Continuing to feed the chipper with brushwood once it has become blocked will cause the chipper to
compact the chips in the rotor housing and it will be difficult and time consuming to clear.
AVOID THIS SITUATION - WATCH THE DISCHARGE TUBE AT ALL TIMES.
DISCHARGE CONTROLS
Controlling the discharge is an
ROTATION 1 essential part of safe working.
1 Slacken nut using
integral handle. BUCKET ANGLE
2 Rotate tube. Adjust the bucket to the desired angle
3 Retighten nut. using the handle provided.

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 13 / 51
TW 160PH

THE FOLLOWING PAGES DETAIL ONLY BASIC MAINTENANCE

GUIDELINES SPECIFIC TO YOUR CHIPPER.
THIS IS NOT A WORKSHOP MANUAL.
The following guidelines are not exhaustive and do not extend to generally accepted standards of
engineering/mechanical maintenance that should be applied to any piece of mechanical equipment and the chassis
to which it is mounted.
Authorised Timberwolf service agents are fully trained in all aspects of total service and maintenance of Timberwolf
wood chippers. You are strongly advised to take your chipper to an authorised agent for all but the most routine
maintenance and checks.
Timberwolf accepts no responsibility for the failure of the owner/user of Timberwolf chippers to recognise generally
accepted standards of engineering/mechanical maintenance and apply them throughout the machine.
The failure to apply generally accepted standards of maintenance, or the performance of inappropriate maintenance
or modifications, may invalidate warranty and/or regulatory compliance, in whole or in part.
Please refer to your authorised Timberwolf service agent for service and maintenance.

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 14 / 51
TW 160PH
SERVICE SCHEDULE
WARNING
ALWAYS IMMOBILISE THE MACHINE BY STOPPING THE ENGINE, REMOVING THE
IGNITION KEY AND DISCONNECTING THE BATTERY BEFORE UNDERTAKING ANY
MAINTENANCE WORK.

Daily 50 100 500 1

SERVICE SCHEDULE
Check Hours Hours Hours Year
Check engine oil - top up if necessary (10W-30). ü
Check for engine oil / hydraulic oil leaks. ü
Check fuel level. ü
Check feed funnel, feed roller cover, access covers,
engine covers and discharge unit are securely fitted. ü
Check blades ü
Ensure engine air intake is free from leaf build up. ü
Check tyre pressure is 2.2 Bar (32 psi). ü
Check safety bar mechanism. ü
Grease the roller box slides. ü OR AS REQUIRED - SEE PAGE 20
Grease the roller spline and bearing. ü OR AS REQUIRED - SEE PAGE 20
Clean air filter element. DEPENDING ON WORKING ENVIRONMENT
Check for tightness all nuts, bolts and fastenings
making sure nothing has worked loose. ü
Grease discharge flange. ü
Check tension of main drive belts (and tension if
necessary). ü
Check anvils for wear. ü
Check fuel pipes and clamp bands. ü
Check battery electrolyte level. ü
Check for loose electrical wiring. ü
Replace hydraulic oil filter - every year or 100 hours
after service or repair work to the hydraulic system. ü OR ü
Replace hydraulic oil. ü OR ü
Replace fuel pipes and clamp bands.
Check spark plugs.
REFER TO YOUR ENGINE
Change engine oil.
SUPPLIERS MANUAL
Replace engine oil filter cartridge.
Check valve clearance.
Replace anvils when worn. RETURN TO DEALER FOR ANVIL CHANGE
Axle maintenance.
REFER TO SUPPLIERS INSTRUCTION SHEET
Tow head maintenance.

NOTE: Your Timberwolf woodchipper is covered by a full 12 months parts and labour warranty. Subject to
correct maintenance and proper machine usage, the bearings are guaranteed for 12 months regardless of hours
worked by the machine. In conditions of 'heavy usage' - i.e. in excess of 500 hours per year - it is recommended
that the bearings are changed annually to ensure that the machine retains optimum working performance.

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 15 / 51
TW 160PH

SAFE MAINTENANCE
ALWAYS IMMOBILISE THE ENGINE BEFORE UNDERTAKING ANY MAINTENANCE WORK ON THE CHIPPER BY
REMOVING THE KEY AND DISCONNECTING THE BATTERY.
• Handle blades with extreme caution to avoid injury. • The major components of this machine are heavy.
Gloves should always be worn when handling the Lifting equipment must be used for disassembly.
cutter blades. • CLEAN machines are safer and easier to service.
• THE drive belts should be connected while changing • Avoid contact with hydraulic oil.
blades, as this will restrict sudden movement of the
rotor.

SAFE LIFTING OF THE CHIPPER

The lifting eye is designed to lift the machine’s weight only. Do not use hoist
hook directly on the lifting eye, use a correctly rated safety shackle. Inspect the
lifting eye prior to each use - DO NOT USE LIFTING EYE IF DAMAGED.

SPARES
Only fit genuine Timberwolf replacement blades, screws and chipper spares. Failure to do so will result in the
invalidation of the warranty and may result in damage to the chipper, personal injury or even loss of life.

BATTERY REMOVAL AND MAINTENANCE

1 Remove the negative lead first and then the positive
lead.
2 Clean, charge and/or top up the battery as required.
3 Refitting is the reverse of removal. Apply a smear of
petroleum jelly to the terminals to prevent corrosion. WARNING
REFER TO THE BATTERY SAFETY
SECTION ON PAGE 17.

CHECK FITTINGS
The Timberwolf TW 160PH is subject to large vibrations during the normal course of operation. Consequently
there is always a possibility that nuts and bolts will work themselves loose. It is important that periodic
checks are made to ensure the security of all fasteners. Fasteners should be tightened using a torque wrench
to the required torque (see below). Uncalibrated torque wrenches can be inaccurate by as much as 25%. It is
therefore essential that a calibrated torque wrench is used to achieve the tightening torques listed below.
Size Pitch Head Torque Ib ft Torque Nm
Blade Bolts M16 Standard 24mm Hex 125 170
Anvil Bolts M10 Standard 8 mm Allen Key 65 88
General M8 Standard 13 mm Hex 20 27
General M10 Standard 17 mm Hex 45 61
General M12 Standard 19 mm Hex 65 88

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 16 / 51
TW 160PH

COPPER EASE SAFETY INFORMATION

Product name: Copper Ease.
Copper Ease contains no hazardous ingredients at or above regulatory disclosure limits, however, safety
precautions should be taken when handling (use of oil-resistant gloves and saftey glasses are recommended -
respiratory protection is not required). Avoid direct contact with the substance and store in a cool, well
ventilated area avoiding sources of ignition, strong oxidising agents and strong acids. Dispose of as normal
industial waste (be aware of the possible existance of regional or national regulations regarding disposal), do
not discharge into drains or rivers.
In case of fire: in combustion the product emits toxic fumes, extinguish with alcohol or polymer foam, carbon
dioxide or dry chemical powder. Wear self-contained breathing apparatus and protective clothing to prevent
contact with skin and eyes.
FIRST AID
Skin contact: there may be mild irritation at the site of contact, wash immediately with plenty of soap and water.

Eye contact: there may be irritation and redness, bathe the eye with running water for 15 minutes.

Ingestion: there may be irritation of the throat, do not induce vomiting, wash out mouth with water.
A safety data sheet for this product can be obtained by writing to the manufacturer at the
following address: Comma Oil and Chemicals Ltd., Deering Way, Gravesend, Kent DA12 2QX. Tel: 01474
564311, Fax: 01474 333000.

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 17 / 51
TW 160PH
BATTERY SAFETY INFORMATION
WARNING NOTES AND SAFETY REGULATIONS FOR FILLED LEAD-ACID BATTERIES
• For safety reasons, wear eye Corrosive hazard: suds, and rinse with plenty of
protection when handling a Battery acid is highly corrosive, water.
battery. therefore: • If acid is swallowed, consult a
• Keep out of reach of • Wear protective gloves and doctor immediately.
children. eye protection. Warning notes: The battery case
• Fires, sparks, naked flames • Do not tilt the battery, acid can become brittle, to avoid this:
and smoking are prohibited. may escape from the vent • Do not store batteries in
• Avoid causing sparks when openings. direct sunlight.
dealing with cables and First aid: • Discharged batteries may
electrical equipment, and • Rinse off acid splashed in the freeze up, therefore store in
beware of electrostatic eyes immediately for several an area free from frost.
discharges. minutes with clear water! Disposal:
• Avoid short circuits. Remove contact lenses if • Dispose of old batteries at an
Explosion hazard: worn and continue rinsing. authorised collection point.
• A highly explosive Then consult a doctor • The notes listed under item 1
oxyhydrogen gas mixture is immediately. are to be followed for
produced when batteries are • Neutralise acid splashes on transport.
charged. the skin or clothes • Never dispose of old
immediately with acid batteries in household waste.
neutraliser (soda) or soap

1. Storage and transport positive output of the charger. Connect the negative
• Batteries are filled with acid. terminal accordingly.
• Always store and transport batteries upright and prevent • Switch on the charger only after the battery has been
from tilting so that no acid can escape. connected, and switch off the charger first after charging
• Store in a cool and dry place. has been completed.
• Do not remove the protective cap from the positive • Charging current-recommendation: 1/10 ampere of the
terminal. battery capacity Ah.
• Run a FIFO (first in-first out) warehouse management • Use a charger with a constant charging voltage of 14.4V
system. for re-charging.
2. Initial operation • If the acid temperature rises above 55o Celsius, stop
charging.
• The batteries are filled with acid at a density of 1.28g/ml
during the manufacturing process and are ready for use. • The battery is fully charged when the charging voltage
has stopped rising for two hours.
• Recharge in case of insufficient starting power (see no. 4).
5. Maintenance
3. Installation in the vehicle and removal from the vehicle
• Keep the battery clean and dry.
• Switch off the engine and all electrical equipment.
• Use a moist anti-static cloth only to wipe the battery,
• When removing, disconnect the negative terminal first. otherwise there is a danger of explosion.
• Avoid short circuits caused by tools, for example. • Do not open the battery.
• Remove any foreign body from the battery tray, and • Recharge in case of insufficient starting power (see no. 4).
clamp battery tightly after installation.
6. Jump Starting
• Clean the terminals and clamps, and lubricate slightly
with battery grease. • Use the standardised jumper cable in compliance with
DIN 72553 only, and follow the operating instructions.
• When installing, first connect the positive terminal, and
check the terminal clamps for tight fit. • Use batteries of the same
nominal voltage only. (2) (1)
• After having fitted the battery in the vehicle, remove the
protective cap from the positive terminal, and place it on • Switch off the engines of
the terminal of the replaced battery in order to prevent both vehicles. 12V 12V

short circuits and possible sparks. • First connect the two

• Use parts from the replaced battery, such as the terminal positive terminals (1) and (2), (3) (4)

covers, elbows, vent pipe connection and terminal then connect the negative
holders (where applicable); use available or supplied filler terminal of the charged battery (3) to a metal part (4) of
caps. the vehicle requiring assistance away from the battery.
• Leave at least one vent open, otherwise there is a danger • Start the engine of the vehicle providing assistance, then
of explosion. This also applies when old batteries are start the engine of the vehicle requiring assistance for a
returned. maximum of 15 seconds.
4. Charging • Disconnect the cables in reverse sequence (4-3-2-1).
• Remove the battery from the vehicle; disconnect the lead 7. Taking the battery out of service
of the negative terminal first. • Charge the battery; store in a cool place or in the vehicle
• Ensure good ventilation. with the negative terminal disconnected.
• Use suitable direct current chargers only. • Check the battery state of charge at regular intervals, and
correct by recharging when necessary (see no. 4).
• Connect the positive terminal of the battery to the

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 18 / 51
TW 160PH

CHANGE BLADES
WARNING
WEAR RIGGERS GLOVES FOR THE BLADE
CHANGING OPERATION.

1 Turn the chipper off and remove the ignition keys.

2 Remove battery leads.
3 3 Remove the M10 bolt retaining the guard, allowing the guard to be
opened.
4 Remove the 3 nuts retaining the access hatch, pull hatch open clear of
4 the rotor housing.
5 Turn rotor to blade change position.
6 Insert locking bar into rotor housing and rotor.
7 Brush away all dirt and debris from the rotor and blades.
8 With a 24mm spanner/socket undo the two nyloc nuts and washers that
are holding the blade in place. Remove both blade bolts from the blade.
9 Grasp the blade by the flat edges while wearing heavy duty gloves.
6
10 Withdraw the blade from the rotor.
11 Clean the back surface of the blade, blade bolts and blade area of the
rotor before reseating blades. The blades must not have any material
underneath them when tightened. If they are not flat and tight they will
become loose very quickly.
5 12 Reassemble the blades, bolts, washers and nuts in the order shown in
the diagram above. Use only genuine Timberwolf nuts and washers, as
they are of a higher grade than normally stocked at fastener
factories.Failure to use the appropriate grade nuts or washers may
result in damage, injury or death. The use of genuine Timberwolf blades
and bolts is recommended.
13 Apply a smear of anti seize compound (copper ease) to the bolt threads
and back face of the nuts. Do not apply copper grease onto the counter
bore faces of the blades or bolts.
12 14 A calibrated torque wrench must be used to tighten the bolts to a
torque setting of 125 lbs ft (170 Nm).
15 Remove lock pin, rotate rotor to next blade then replace lock pin and
repeat steps 7 - 14.
16 Refit access hatch.
17 Refit the nuts and tighten to 45lb/ft.
18 Refit battery leads.

WARNING
ALWAYS SHARPEN BLADES ON A REGULAR BASIS. FAILURE TO DO SO WILL
CAUSE THE MACHINE TO UNDER PERFORM AND WILL OVERLOAD ENGINE
AND BEARINGS CAUSING MACHINE BREAKDOWN. BLADES MUST NOT BE
SHARPENED BEYOND THE WEAR MARK (SEE DIAGRAM). FAILURE TO
COMPLY WITH THIS COULD RESULT IN MACHINE DAMAGE, INJURY OR
LOSS OF LIFE. WEAR MARK

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 19 / 51
TW 160PH

TENSION BELTS
NOTE: There will normally be a rapid drop in tension during run-in period for new belts. When new belts are fitted,
check the tension every 2 - 3 hours and adjust until the tension remains constant.
Belt failures due to lack of correct tensioning will not be covered under your Timberwolf warranty.
TENSION DRIVE BELTS
1 Remove belt guard.
2 Loosen bolt in centre of tensioner pulley with a 19mm spanner so that pulley is able to slide with minimal
wobble.
3 Turn nut in end of tensioner pulley slider until correct belt tension is
3 achieved. For instructions on checking belt tension & correct belt
tension values, please refer to the Timberwolf V-Belt Tensioning Data
Table (page 30).
4 Retighten bolt in centre of tensioner pulley.
5 Refit belt guard.
6 Run machine and test, recheck belt tension.
2 NOTE: Slack drive belts will cause poor performance and excess belt and
pulley wear.

TENSION HYDRAULIC PUMP BELT

1 Remove belt guard.
2 Access the two nuts on the under side of the chassis and slacken using a
19 mm socket spanner.
3 Adjust the M8 bolt on the outside plate until the desired tension is
achieved. For instructions on checking belt tension & correct belt tension 3
values, please refer to the Timberwolf V-Belt Tensioning Data Table (pg.
30).
4 Retighten the two nuts to (88 Nm) 65 lbs/ft. 2
5 Refit belt guard.

CHANGE HYDRAULIC OIL AND FILTER

WARNING
USE PLASTIC GLOVES TO KEEP OIL OFF SKIN AND DISPOSE OF THE USED OIL AND FILTER
IN AN ECOLOGICALLY SOUND WAY. THE OIL AND FILTER SHOULD BE CHANGED ONCE A
YEAR OR AT ANY TIME IT BECOMES CONTAMINATED. BEFORE STARTING CHECK THAT
THE CHIPPER IS STANDING LEVEL AND BRUSH AWAY LOOSE CHIPS.

1 Remove the black screw cap from the top of the filter
1
housing.
2 Partially remove filter element from inner cup. Leave
filter to drain for 15 minutes.
3 Remove filter element from cup when clear of hydraulic
oil.
4 Remove drain plug and drain oil into a suitable container.
5 Replace drain plug.
6 Refill with VG 32 hydraulic oil until the level is between
the min and max lines on the tank (about 15 litres).
2 4 7 Refit the filter cup, install a new filter element and refit
the black screw cap, to the filter housing, ensuring o-ring
NOTE: This is a non-adjustable air breather filter. remains in place.

C190-0013 11.04.2019
 SERVICE INSTRUCTIONS 20 / 51
TW 160PH
GREASE THE ROLLER SPLINE AND ROTOR BEARINGS
NOTE: This should be done regularly. In dirty and dusty conditions or during periods of hard work it should
be daily. If the bearings and splines are allowed to run dry premature wear will occur resulting in a
breakdown and the need for replacement parts. This failure is not warranty. Early signs of insufficient
grease includes squeaking or knocking rollers.
1 Locate the greasing panel.
2 Apply 4+ pumps of grease to each nipple.
3 It is recommended to grease all the nipples whilst the engine is running
1 A and rollers are turning to distribute the grease evenly. DO NOT USE
GRAPHITE BASED GREASE.
B
4 Both front and rear bearings are greased by nipples A and B. The top
C and bottom roller splines are greased by nipples C and D.
D

GREASE THE ROLLER BOX SLIDES

NOTE: This should be done regularly. In dirty or dusty conditions or during periods of hard work it should be
done weekly. If the slides become dry the top roller will tend to hang up and the pulling-in power of the
rollers will be much reduced. Excessive wear will ensue.
1 Turn the chipper off and remove the ignition keys.
2 Ensure machine has come to a complete stop - remove battery leads.
5
3 Remove the bolt and washer retaining roller box guard and lift guard.
4 Remove the two springs on the roller box slide.
5 NOTE: Rollerbox slide weighs in excess of 20kg. Lift the top roller and
wedge a suitably sized piece of wood to hold in place.
6
6 Apply thin grease with a brush to each slide on roller box and on inner
cheeks of slider. DO NOT USE GRAPHITE BASED GREASE.
7 NOTE: Rollerbox slide weighs in excess of 20kg. Remove wedge, lower
roller box slide and replace springs.
8 Close roller box guard making sure that it is located over the retaining 3
bracket, and ensure bolt and washer (as note 3) are tightened. 4
9 Refit battery leads.

GREASE THE DISCHARGE FLANGE 2

1 Remove the discharge tube.
2 Apply multipurpose grease to surface shown.
3 Refit discharge tube.

ENGINE SERVICING
All engine servicing must be performed in accordance with the Engine Manufacturer’s handbook provided with
the machine. FAILURE TO ADHERE TO THIS MAY INVALIDATE WARRANTY AND/OR SHORTEN THE LIFE OF THE
ENGINE.
CHECK HOSES
All the hydraulic hoses should be regularly inspected for chafing and leaks. The hydraulic system is pressurized to 150
Bar and thus the equipment containing it must be kept in good condition.
Identify the hoses that run to the top motor. These have the highest chance of damage as they are constantly moving.
If any hydraulic components are changed new seals should be installed during reassembly. Fittings should then be
retightened.

C190-0013 11.04.2019
 WARRANTY STATEMENT 21 / 51
TW 160PH

TIMBERWOLF NO-NONSENSE WARRANTY

All new Timberwolf machines come with peace of mind built in. Our no-nonsense warranty is your guarantee of your
Timberwolf wood chipper not letting you down.
Your warranty statement is included in your manual pack. Please ensure you register your machine with your dealer to
ensure you are eligible for the full Timberwolf warranty period.

C190-0013 11.04.2019
 DECLARATION OF CONFORMITY 22 / 51
TW 160PH

C190-0013 11.04.2019
 IDENTIFICATION PLATE 23 / 51
TW 160PH

L E
P
A M
EX

C190-0013 11.04.2019
 DECALS 24 / 51
TW 160PH

Decal Description Decal Description

616 4099 x 2

Danger.
Hot exhaust Rotating blades.
Keep hands and feet out.

617 2800 2801

Reverse feed
High velocity discharge -
keep clear
Forward feed

670 18393
New drive belts need re-
tensioning.
Personal Protective When new belts are fitted
Equipment required check tension every 2-3 hours
& adjust until tension remains
constant.

1661 1399

Read the instruction Push to stop.

manual for greasing and
maintenance information Do not pull here.
P691 x 2

1662 2949
Lifting eye is designed to lift
The instruction manual
the machine’s weight only.
with this machine contains
Do not use hoist hook directly
important operating,
on lifting eye. Use correctly
maintenance and health
rated safety shackle only
and safety information.
through lifting eye. Lifting eye
Failure to follow the
to be inspected every 6
information contained in
months or before each use.
the instruction manual
Always visually inspect lifting
may lead to death or
eye prior to each use. Do not
serious injury.
use lifting eye if damaged.

18438 3022
When re-fitting this guard
ensure that steel retaining
bracket is on the inside. Clean under blades before
Damaged guards due to refitting or turning. Failure to do
incorrect assembly will not so may result in blade(s) coming
be covered by your loose and damage being caused
Timberwolf warranty. to the rotor housing

C190-0013 11.04.2019
 DECALS 25 / 51
TW 160PH

Decal Description Decal Description

P637 x 4 P653
Danger.
Danger.
Rotating blades inside.
Do not operate without this
cover in place. Stop engine and remove key
before removing discharge unit.

P652 P654

Caution. Do not put road Caution. When transporting,

sweepings in machine as grit will discharge clamps may work
damage blades. loose.Check frequently.

P655 P656
Caution. Danger.
Avoid standing Do not use this
directly in front of feed funnel to machine without the
reduce exposure to noise, dust discharge unit fitted. failure to
and risk from comply may result in
ejected particles. serious inury or damage.

P650 Danger. Autofeed system P651

Fuel Here.
fitted. Rollers may turn
Risk of fire. Allow engine
without warning!
to cool for 1 minute before
When the engine is switched off
refuelling.
the rollers will turn during
Use unleaded petrol.
the run down period.

C192-0181 C192-0180

Always cover ignition switch with

Do not jet wash in this area. plug provided when towing or jet
wash cleaning.

L Aeq L WA

95 117 KG M
TIMBERWOLF
850

AX

dB dB TW 160PH
3013 C192-0103 1363 1849 P*2837 X 2

TIMBERWOLF
TW 160PH(a)
C192-0116 1136

C190-0013 11.04.2019
 ELECTRICAL PARTS LOCATOR 26 / 51
TW 160PH

Spark Plug Inductive Sensor

D.C.V.
Speed Switch

Funnel Loom Connector

Safety Bar Switch Control Box Switches x 2

C190-0013 11.04.2019
C190-0013
CIRCUIT DIAGRAM
27 / 51

11.04.2019
TW 160PH

CIRCUIT DIAGRAM FOR: 160 PETROL VERSION Document no. 160 - CD Issue 2
C190-0013
CIRCUIT DIAGRAM
28 / 51

11.04.2019
TW 160PH

CIRCUIT DIAGRAM FOR: 160 PETROL VERSION Document no. 160 - CD Issue 2
 HYDRAULIC LAYOUT 29 / 51
TW 160PH

Hose kit No. CO73-106

TANK

FILTER
CO73-100

CO73-102
PUMP

CO73-101

DCV

CO73-103 CO73-104

TOP MOTOR BOTTOM

MOTOR

CO73-105

C190-0013 11.04.2019
 V-BELT TENSIONING TABLE 30 / 51
TW 160PH

Method:
1 Set the deflection distance on the lower scale of the tension gauge so that the underside of the 'o'-ring equals the
'h' value given in the table.
2 Ensure that the deflection force scale is zero'd by pushing the upper 'o'-ring all the way down.
3 Place the tension gauge in the centre of the belt span as shown in the diagram.
4 Press downwards on the rubber buffer, deflecting the belt until the underside of the lower 'o'-ring is level with
the belt behind (use a straight edge if there is only 1 belt).
5 Take the reading from the deflection scale of the tension meter (read at the lower edge of the 'o'-ring) & compare
this value with that given in the table.
6 Tighten or loosen belts as required following procedure given in this operator's manual.
Tension gauges are available from Timberwolf spares, quoting part no. 18091

Rotor
ROTOR BELTS Pulley Rotor PUMP BELTS
Pulley

Belt
Tensioner

Engine Pulley Pump

Pulley

160PH Rotor Belts Pump Belts

Belt Mffr / Type Gates Super HC-MN Gates Super HC-MN
Belt Pitch Designation SPA SPA
Belt Length in mm 1030 900
Belt Deflection in mm =h 2 2
New belt 3.75 - 4.01 3.94 - 4.22
Force Reading (Kg)
Used Belt 3.21 - 3.47 3.38 - 3.66

TIPS ON BELT TIGHTENING:

• There will normally be a rapid drop in tension during the • Too much tension shortens belt & bearing life.
run-in period for new belts. when new belts are fitted, • Too little tension will affect the performance of your
check the tension every 2-3 hours & adjust until the machine especially in respect of no-stress devices.
tension remains constant. • Ensure that belt drives are kept free of any foreign
• The best tension for v-belt drives is the lowest tension at materials.
which the belts do not slip or ratchet under the highest • If a belt slips - tighten it!
load condition.

C190-0013 11.04.2019
 WARRANTY SERVICE RECORD CHECK 31 / 51
TW 160PH

Model number: Serial number:

Date of delivery/ Options/extras:

handover:
Dealer pre
delivery check:

Inspected by:

50 HOUR WARRANTY SERVICE CHECK Authorised dealer stamp

Date:

Hours:

Invoice number:

Signature:

Next service due:

11 MONTH WARRANTY SERVICE CHECK Authorised dealer stamp

Date:

Hours:

Invoice number:

Signature:

Next service due:

23 MONTH WARRANTY SERVICE CHECK Authorised dealer stamp

Date:

Hours:

Invoice number:

Signature:

Next service due:

C190-0013 11.04.2019
 SERVICE RECORD 32 / 51
TW 160PH

Date: Authorised dealer stamp

Hours:

Invoice number:

Signature:

Next service due:

Date: Authorised dealer stamp

Hours:

Invoice number:

Signature:

Next service due:

Date: Authorised dealer stamp

Hours:

Invoice number:

Signature:

Next service due:

Date: Authorised dealer stamp

Hours:

Invoice number:

Signature:

Next service due:

C190-0013 11.04.2019
 PARTS LIST 33 / 51
TW 160PH

PARTS LISTS
THE FOLLOWING ILLUSTRATIONS ARE FOR PARTS IDENTIFICATION ONLY. THE REMOVAL OR FITTING OF THESE
PARTS MAY CAUSE A HAZARD AND SHOULD ONLY BE CARRIED OUT BY TRAINED PERSONNEL.

Page No.
BELT TENSIONER 34
CHASSIS (1) 35
CHASSIS (2) 36
CONTROL BOX 37
DISCHARGE 38
DRIVE TRAIN 39
ELECTRICAL LAYOUT 40
ENGINE 41
FUNNEL 42
FUEL TANK 43
HYDRAULIC TANK 44
HYDRAULICS 45
ROLLER BOX 46
ROLLER SLIDES 47
ROTOR 48
ROTOR HOUSING 49
DECALS 50

C190-0013 11.04.2019
 34 / 51
TW 160PH

C190-0012 11.04.2019
 35 / 51
TW 160PH

C190-0012 11.04.2019
 36 / 51
TW 160PH

C190-0012 11.04.2019
 37 / 51
TW 160PH

C190-0012 11.04.2019
 38 / 51
TW 160PH

C190-0012 11.04.2019
 39 / 51
TW 160PH

C190-0012 11.04.2019
 40 / 51
TW 160PH

3 1

5
4

Item Part No Part Name Q’ty Item Part No Part Name Q’ty
1 P2818 Funnel Loom 1 4 P2513 -
VE Battery Cable 1
2 P2817 Engine Loom 1 5 P2512 +
VEBattery Cable 1
3 1638 No Stress Sensor 1

C190-0012 11.04.2019
 41 / 51
TW 160PH

C190-0012 11.04.2019
 42 / 51
TW 160PH

C190-0012 11.04.2019
 43 / 51
TW 160PH

C190-0012 11.04.2019
 44 / 51
TW 160PH

C190-0012 11.04.2019
 45 / 51
TW 160PH

C190-0012 11.04.2019
 46 / 51
TW 160PH

C190-0012 11.04.2019
 47 / 51
TW 160PH

C190-0012 11.04.2019
 48 / 51
TW 160PH

C190-0012 11.04.2019
 49 / 51
TW 160PH

C190-0012 11.04.2019
C190-0012
TIMBERWOLF
18438 TW 160PH
P2837

1849

KG M 2801 2800

850
AX
18393

P652

2949
50 / 51

11.04.2019
P655

670
TW 160PH

P637 1662 P650

 1363
P2837 P653

C190-0012
TIMBERWOLF
TW 160PH
P656

P637
x2

4009 3022 P654

51 / 51

11.04.2019
616

P691

1661

L WA L Aeq
1399

117 dB 95 dB
C192-0103 3013
TW 160PH

2800 2801 P651

 Timberwolf Wood Chippers & Shredders
Tomo Industrial Estate, Stowmarket, Suffolk IP14 5AY, United Kingdom
T: +44 1449 765809 E: info@timberwolf-uk.com W: timberwolf-uk.com

timberwolf-uk.com