CRE Config Software

User Manual

CRE Technology believes that all information provided herein is correct and reliable and reserves
the right to update at any time. CRE Technology does not assume any responsibility for its use
unless otherwise expressly undertaken.

CRE Technology
130 Allée Charles-Victor Naudin
Zone des Templiers - Sophia Antipolis
06410 BIOT - FRANCE
Phone: + 33 (0)4.92.38.86.82 - Fax: + 33 (0)4.92.38.86.83
www.cretechnology.com - info@cretechnology.com
SARL au Capital de 300.000 Euros - RCS Antibes: 7488 625 000 15 N°TVA FR54 488 625 583
Table of Contents
1 Overview ..................................................................................................................... 3
2 Installation .................................................................................................................. 4
2.1 System requirements ................................................................................................. 4
2.2 Hardware installation ................................................................................................ 4
2.3 Software installation ................................................................................................. 4
2.4 Windows 7/Vista installation troubles ....................................................................... 4
3 Password protection .................................................................................................... 6
4 Description .................................................................................................................. 7
4.1 Home page ................................................................................................................ 7
4.2 Menu and Toolbar ..................................................................................................... 7
4.2.1 File menu ....................................................................................................... 8
4.2.2 Options menu ................................................................................................. 8
4.2.3 Help menu ...................................................................................................... 8
4.2.4 Toolbar ........................................................................................................... 8
(*)
4.3 Scada /Configuration/System .................................................................................. 9
5 GENSYS 2.0/MASTER 2.0 Family .......................................................................... 10
5.1 Scada ...................................................................................................................... 10
5.2 Log view ................................................................................................................. 11
5.3 Configuration .......................................................................................................... 12
5.4 General ................................................................................................................... 13
5.5 Calibrating an analog input ..................................................................................... 15
5.6 Enable/Disable module options ............................................................................... 17
5.7 System setting ......................................................................................................... 18
5.8 Manually modifying a variable ............................................................................... 19
5.10 File upload/download .......................................................................................... 20
6 UNIGEN Family ....................................................................................................... 21
6.1 UNIGEN Display.................................................................................................... 21
6.2 UNIGEN Configuration .......................................................................................... 22
6.3 Modifying a parameter ............................................................................................ 23
6.4 Modifying any variable ........................................................................................... 24
6.5 UNIGEN System .................................................................................................... 25
6.6 File upload/download.............................................................................................. 26

A70 Z1 90002-C - User manual 2/26

 Overview

1 Overview
CRE Config Software allows the user to easily access to multiple CRE technology modules of
the GENSYS 2.0/MASTER 2.0 family through an Intranet network as well as a UNIGEN family
module through a modem connection (a single UNIGEN module at a time). Engineers or
technicians can configure a device online/offline and monitor the device in real-time. The
software's organization follows exactly the classical GENSYS 2.0 embedded web-server so that
users who are used to it can be operational immediately with this software. His friendly and
innovative interface gives the users a total new and ergonomic working experience.

The CRE Config Software should only be used by competent, qualified personnel, as changes to
the operation of the module may have safety implications on the panel/generating set to which it
is fitted. Access to critical operational sequences and settings are to be used by qualified
engineers, only a security code set by the generator provider will prevent unauthorized access.

This application should be used together with the technical documentation of the module you
want to connect.

It is necessary to use CRE technology products that handle the communication protocol used by
CRE Config Software. Table below indicates the minimal firmware version for each product
family that will be compatible with CRE Config Software.

Product family CRE Config Software compatible firmware

A53Zx – GENSYS 2.0 / MASTER 2.0 Starting from v3.00
A51Zx – UNIGEN Starting from v2.00

A70 Z1 90002-C - User manual 3/26

 Installation

2 Installation
2.1 System requirements
 Supported Operating Systems: Windows 7, Windows Vista, Windows XP, Windows
Server 2008, Windows Server 2003.
 Processor: 400 MHz Pentium processor or equivalent (Minimum); 1GHz Pentium
processor or equivalent (Recommended)
 RAM: 128 MB (Minimum); 256 MB (Recommended)
 Hard Disk: Up to 200 MB of available space may be required
 Display: 800 x 600, 256 colors (Minimum); 1024 x 768 high color, 32-bit (Recommended)
 Ethernet: 10 Mbps - 10Base-T Ethernet or higher
 Microsoft .NET Framework 3.5 Service Pack 1

2.2 Hardware installation

Connect GENSYS 2.0 module directly to PC via Ethernet cable or connect it to LAN (Local
Area Network).
CRE Config Software doesn’t handle the modem connection with UNIGEN, you must manually
establish this modem connection (see specific UNIGEN documentation A51Z1 9 0015A).

2.3 Software installation

Make sure the PC running this application has Microsoft .NET Framework 3.5 Service Pack 1,
which can be downloaded here.
To install the software, run the executable file Setup CRE Config Software. If the following
dialog box appears under Windows 7/Vista, then select “Yes”:

Figure 1: Windows 7/Vista user account control

2.4 Windows 7/Vista installation troubles

Installing the software requires administrator privileges. If you are not administrator of your
computer, right click on the Setup CRE Config Software icon and select “Run as
administrator” as shown below to install the software.

A70 Z1 90002-C - User manual 4/26

 Installation

Figure 2: Windows 7/Vista requires administrator privileges

If you don’t have administrator privileges, then the setup will end up with the following error:

Figure 3: Windows 7/Vista setup error

A70 Z1 90002-C - User manual 5/26

 Password protection

3 Password protection

CRE Config Software uses the traditional password of the CRE Technology modules for access
permissions and change the parameters of the connected module.

Level Default password Authorization Accessible menu

No password, just
0(*) This level is not password protected. Display
press [Connect] button
User level.
1 1 (just digit “one”) All menus
Parameters settings & level 1 equations
Reserved to CRE
Distributor level.
2 technology All menus
Level 1 & 2 equations and parameters
distributors.
(*) Not available on UNIGEN range.

To connect to your device, enter its hostname and password in fields Device name and Password
in the Connect to Device section (see image below and next chapters for further details).

Device Name can be found in the System/Serial number – Soft version menu of the CRE
technology device menu. In the case of UNIGEN, IP address of the module (default is
192.168.11.1) serves as the Device Name. Thus only one UNIGEN connection can be
established at a time.

Password is the same as the one used to access the embedded Web site of your CRE technology
module.

A70 Z1 90002-C - User manual 6/26

 Description

4 Description
4.1 Home page
This page will be displayed when users start the application. Click on a product icon to create a
new session or Open a recent file from File menu or Toolbar.

Figure 4.1: Homepage

Note: CRE Config Software can configure and monitor several modules simultaneously with
one tab for each of them. CRE Config Software can control a set of several GENSYS 2.0 at the
same time.
4.2 Menu and Toolbar

Figure 4.2: Menu and Toolbar

The Menu and Toolbar are at the top of the screen.

A70 Z1 90002-C - User manual 7/26

 Description

4.2.1 File menu

Create a new module configuration file.
Open an existing file from disk or flash memory device
Save the current open file with the path it was loaded from
previously. If this is a new file, users are prompted to enter the
file name.
Save the currently open file with a new name. Users will be
prompted to enter the file name.
Preview what the configuration file will look like on the page
after printing.
Print the current open configuration file.
Exit the software. If the current open file has changed since it
was last saved, users will be prompted to save it.

4.2.2 Options menu

Choose the language of your CRE Config Software
Choose theme for the application

4.2.3 Help menu

Open this help file.
Show the version number of this configuration application.

4.2.4 Toolbar
Toolbar contains the most used commands from the menu and is a quicker way to access these
commands.

Create a new configuration file.

Open an existing file from disk or flash memory device

Save the current open file with the path it was loaded from
previously. If this is a new file, users are prompted to enter the
file name.
Print the current open configuration file.
Send configuration parameters of the current page to the
module.
Send configuration pages to the module.

Read the settings from the module for viewing/editing

A70 Z1 90002-C - User manual 8/26

 Description

4.3 Scada(*)/Configuration/System

Scada/Display Configuration

System

Figure 4.3: Scada(*)/Configuration/System

3 main sections are available to the user:

 Scada(*): to monitor all measurements (electrical, engine meters...).
(*)
Display on UNIGEN range
 Configuration: to read and modify configuration parameters of your CRE technology
product.
 System: to read and modify system parameters of your CRE technology product (date,
hour, module language...).

For more details, please refer to the chapters 5 and 6

A70 Z1 90002-C - User manual 9/26

 Scada

5 GENSYS 2.0/MASTER 2.0 Family

5.1 Scada
In this mode, CRE Config Software allows the users to monitor the electrical and mechanical
parameters in real time.
Before running in Scada mode, users have to insert Device Name and Password to connect to the
CRE technology module to be monitored.

Device name

Device password

Figure 5.1: Example of monitoring page

Connecting status

Users can use Information Display page to read parameter of 50 different variables by inserting
their labels.

A70 Z1 90002-C - User manual 10/26

 Log view

5.2 Log view

This page allows you to read data stored by the module and copy them to the clipboard.

Figure 5.2: Log view

Update log Print the list
Copy the list to clipboard

A70 Z1 90002-C - User manual 11/26

 Configuration

5.3 Configuration

In Configuration section , users can set parameter values. But this only affects the
parameters in GENSYS 2.0 when users transfer them into the device. There are 2 ways to do so:

 “Upload current page to device” : Transfer all parameters of the actual displayed
page into the device

 “Upload all to device” : Transfer all parameter into the device.

Note: The module may to save or reject parameters depending on password level and option
enabled.
For more information about how to change the value of parameters, users should refer to
Technical Documentation.

Attention: For the CRE device to save definitely new values received from CRE Config
Software, user must manually make a “Shift-I”.

Figure 5.3: Configuration mode

A70 Z1 90002-C - User manual 12/26

 General

5.4 General
Users should consult GENSYS 2.0 technical documentation A53 Z0 9001 for right adjustment.
To modify value of corresponding variable, user selects page that contains the variable and edit
it.
For example:

Click to increase value

Click to increase number

Click to decrease value

Click to decrease number

Click to select from list

Click to select from list

Drag
Drag slide to slide
changeto change
value value

Click to switch value

Click to switch value

Figure 5.4: Example of configuration page

After modifying, users can select “Transfer current page to device” to upload the variables
shown in the current page to configure the module or select “Transfer all page to device” to
upload all pages to the module.

A70 Z1 90002-C - User manual 13/26

 General

Note: Some parameters can be inhibited according to the current configuration. In the
example below, selecting “Alternator” as the speed measurement source makes
parameter "number of teeth” of the pick-up useless. It is therefore inhibited.

Disabled variable
Inhibited variable

Figure 5.4: Example of configuration page

A70 Z1 90002-C - User manual 14/26

 Calibrating Analog Input

5.5 Calibrating an analog input

For easier set up of an analog input, users can edit the calibration by using graph:

Figure 5.5: Analog input calibration

A70 Z1 90002-C - User manual 15/26

 Calibrating Analog Input

Drag to change value

Save graph to file

Load graph from file

Value of selected item

Apply Figure 5.5: Analog input calibration by graph
Cancel

A70 Z1 90002-C - User manual 16/26

 Options

5.6 Enable/Disable module options

In order to enable or disable an option, type the device name and the corresponding option
password in the connection fields and then click Connect.

Type password option

here

Figure 5.6: Connection window

Please contact your CRE technology distributor to obtain the password corresponding to the
desired option.

A70 Z1 90002-C - User manual 17/26

 System

5.7 System setting

In the system mode, users can modify the system configuration: date, time, screen saver, timer,
logo…

Attention: To definitely save parameters into your CRE technology device (GENSYS 2.0 and
MASTER 2.0), user must manually press on “Shift-I” on the front panel of the module.

Figure 5.7: System mode

A70 Z1 90002-C - User manual 18/26

 Modifying a variable

5.8 Manually modifying a variable

In this mode, users can change value of a corresponding variable by inserting its number in
“Modify Variable by Number” page.

Type variable number then click search

Change variable value

Figure 5.8: Modify Variable

Click to upload the value

If password level is 2, user can change “Modify by MODBUS/PLC” option. In this case, the
variable can be changed in the module equation or through MODBUS communication.

Figure 5.8: Modify by MODBUS/PLC

A70 Z1 90002-C - User manual 19/26

 File upload/download

5.10 File upload/download

Download device variables

Download log file

Download log file

Click to select
Clickfile
to select file

Upload selected file to

Upload device
selected file to device

Figure 5.10.1: Upload/Download page

Once clicked on Upload/Download, a progress dialog will appear:

When upload completes or fails, the result is displayed as shown below:

A70 Z1 90002-C - User manual 20/26

 UNIGEN Display

6 UNIGEN Family
6.1 UNIGEN Display
In this mode, users can see the different electrical measurements and Inputs/Outputs of the
module in real time. Before running the Display mode, users must connect to the CRE
technology module.

Figure 6.1: Example of the Display page.

Information page allows users to view on the same page parameters and measurements of their
choice. To do this, enter the number of each measure/parameter to display.

A70 Z1 90002-C - User manual 21/26

 UNIGEN Configuration

6.2 UNIGEN Configuration

In Configuration section , users can read and set parameters values. The changes only take
effect when new values are sent to the connected module. There are 2 ways to do so:

 “Upload current page to device” : transfers all parameters of the actual displayed
page into the device

 “Upload all to device” : transfers all parameters into the device.

Note: module may save or reject parameters depending on password level and enabled options.
For more information about how to change the value of parameters, users should refer to the
technical documentation of the module.

Attention: refer to section 6.5 in order to keep the configuration changes permanently saved into
a module.

Figure 6.2: Configuration

A70 Z1 90002-C - User manual 22/26

 Modification of parameter UNIGEN

6.3 Modifying a parameter

To change the value of a parameter, go to the configuration page and edit the associated value.
For more details concerning the setup of a UNIGEN module, refer to technical documentation
A51 Z0 9 0004.

Figure 6.3: Example of configuration page

After modification, select the “Upload current page to device” icon to send displayed settings to
the connected module. Select “Upload all to device” icon to send the entire configuration to the
connected module.

A70 Z1 90002-C - User manual 23/26

 Modification of variable UNIGEN

6.4 Modifying any variable

This page allows you to change a parameter using its variable number.

Figure 6.4: Modify Variable

Note that if you are connected to the module using level 2 password, it is also possible to change
the read/write attribute of the parameter. This attribute is checked by the module for MODBUS
write accesses.

Figure 6.4: MODBUS/PLC read/write attribute

A70 Z1 90002-C - User manual 24/26

 UNIGEN System

6.5 UNIGEN System

This section allows you to read the serial number of your module and to download, upload and
save its configuration.

Attention: after sending parameters to the module, press “Flash it” button to permanently save
the new configuration.

Figure 6.5: System

A70 Z1 90002-C - User manual 25/26

 File upload/download UNIGEN

6.6 File upload/download

Download log file

Click to select file

Figure 6.5: Upload/Download page

Once clicked on Upload/Download, a progress dialog will appear:

When upload completes or fails, the result is displayed as shown below:

A70 Z1 90002-C - User manual 26/26