SE / Se: Single Equipment Controller

SE6166 / SE6104a
Single Equipment Controller
Automated Logic’s powerful SE line provides a rugged solution for single equipment applications. Designed to
operate in a wide range of environmental conditions, SE controllers can be used in rooftop units, mechanical
rooms, equipment closets, or almost any other weather tight location. Fully programmable using the EIKON®-
LogicBuilder graphic programming language, SE controllers use native BACnet communications over either a
high-speed ARCNET 156 Kbps network or a medium speed MS/TP network to provide maximum flexibility and
interoperability.
Key Features and Benefits

• Native BACnet communications to field devices over a high-speed ARCNET 156 Kbps or BACnet MS/TP
network.
• 12-bit Analog to Digital converter provides extreme precision on all inputs. Pulse counting capability up to 40
Hz is available on selected inputs.
• Uses a high-speed microprocessor with 1 MByte Flash memory and 1 MByte of RAM for unparalleled
programmability. Firmware upgrades can be downloaded remotely – no chip replacement necessary.
• Battery backed real-time clock provides true stand-alone capabilities. Control modules recover from power
failures providing full continuity of scheduled operations, even when communications are disrupted.
• Rnet port supports Automated Logic’s line of RS room sensors and BACview6 local operator interface, and
provides local access to the system.
• SE line controllers are fully graphically programmable and offer full peer-to-
peer communications with
other SE line, ME line or ZN line controllers. Graphical programs are
universally understood and provide
self-documenting control sequences. 1150 Roberts Boulevard
• Tough construction delivers superior performance and reliability. Control Kennesaw, Georgia 30144
modules are constructed with a rugged aluminum cover, which provides 770/429-3000
Fax 770/429-3001
optimum electrical protection and noise immunity. www.automatedlogic.com
SE6166 / SE6104a
Specif ications
BACnet® Support: Conforms to the Advanced Application Controller (B-AAC) Standard Device Profile as defined in ANSI-ASHRAE Standard
135-2004 (BACnet) Annex L. Tested to Protocol Revision 9
Communication: The following ports are available on the SE control modules:
EIA-485 port for ARCNET 156 Kbps or MS/TP (9600 bps – 76.8 kbps).
Rnet Port supports:
1. Local access for system start-up and troubleshooting.
2. Local operator interface BACview6.
3. RS Room Sensors - one RS Pro and up to four RS room sensors for averaging or high/low select control.
Binary Outputs: SE6166 and SE6104a have six binary outputs, relay contact rated at 3A max @ 24 V-ac, configured normally open with
hand-off auto switches.
Universal Inputs: SE6166 - 16 configurable universal inputs, SE6104a - 10 configurable universal inputs, both with 12-bit A/D resolution.
Supported input types include: 0-5 V-dc, 0-10 V-dc, 0-20 mA, Thermistor (10k Ohm Type II), 1k Ohm RTD (Platinum, Nickel
or Balco), and Dry Contact.
NOTE: Inputs 1 and 2 support pulse counting up to 40 cycles per second (40 Hz).
Analog Outputs: SE6166 - six analog outputs, SE6104a - four analog outputs, both with 0-10 V-dc or 0-20mA selectable with 8-bit resolution.
Microprocessor: High speed microprocessor with ARCNET communication co-processor.
Memory: 1 MByte non-volatile battery-backed RAM, 1 MByte Flash memory, 16-bit memory bus. (Shelf life of the battery is 10 years
with 10,000 hours of continuous operation.)
Real-time Clock: Battery-backed real-time clock.
Status Indicators: LED status indicators for EIA-485 communication, running, error, power and all digital outputs.
Module Addressing: Rotary dip switches for intuitive network addressing of modules.
Protection: Built-in surge and transient protection circuitry for power, communications, inputs and outputs.
Listed by: UL916 (Canadian Std C22.2 No. 205-M1983), CE, FCC Part 15 – Subpart B – Class A.
Environmental Operating Range: -20ºF to 140ºF (-29ºC to 60ºC); 10 to 90% relative humidity, non-condensing.
NOTE: Control modules should be mounted in protective enclosures.
Power Requirements: 24 V-ac ± 10%, 50 to 60Hz, 20VA.
NOTE: Power consumption will increase when BACview or other accessories are attached.
Physical: Rugged aluminum cover. Removable screw terminal blocks.
Weight: 0.6 lb. (0.27 kg).
Dimensions:
Overall Mounting
Width: 8.3” (211mm) Width: 7.835”(199mm)
Height: 7” (178mm) Height: 5” (127mm)
Depth: 1.5” (38mm) min. panel depth 5” mounting hole spacing
Automated Logic Corporation . 1150 Roberts Boulevard . Kennesaw, Georgia 30144 . 770/429-3000 . Fax 770/429-3001 . www.automatedlogic.com
© United Technologies Corporation 2013. All rights reserved. Copyright Policy
BACnet is a registered trademark of ASHRAE. All other trademarks are the property of their respective owners. Specifications are subject to change without prior notice.
Automated Logic is a part of UTC Building & Industrial Systems, a unit of United Technologies Corp
Made in the USA SE_CS_11062014

SE / Se: Single Equipment Controller

Uploaded by

Copyright:

Available Formats

SE / Se: Single Equipment Controller

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SE / Se: Single Equipment Controller

Uploaded by

Copyright:

Available Formats

SE6166 / SE6104a

Single Equipment Controller

Key Features and Benefits

You might also like