4 Channel DVR: User Manual

4 CHANNEL DVR
User Manual SDE-3001/3003
Downloaded from www.Manualslib.com manuals search engine

4 Channel DVR
User Manual
Copyright
©2011 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced,
distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the
right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge.
The warranty period is 3 years. However, the followings are excluded:
• Data loss due to a damaged hard disk
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Data loss due to virus infection
• Deteriorated performance or natural worn-out in process of time
• Sensory phenomenon that does not affect the performance or quality of the product (ex: working noise).
 Design and specifications are subject to change without prior notice.
 The default password can be exposed to a hacking thread so it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

overview
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
 OVERVIEW
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. if the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
English _3
overview
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on
top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause fire
or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this
product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted
repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
11. Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between
internal and external of the dome camera.
12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with
silicon, so that the external air can not flow inside the housing.
Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product
due to a difference between internal and external temperature.
4_ overview
BEFORE START
This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, etc.
You have to keep in mind the following notices :
• SAMSUNG retains the copyright on this manual.
• This manual cannot be copied without SAMSUNG’s prior written approval.
• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
 OVERVIEW
removed from the unit.
• Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this
DVR, check the compatibility. Consult your provider for the compatibility list.
Warning
❖ Battery
It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifications of the battery you are using now.
• Normal voltage : 3V
CALIFORNIA USA ONLY
• Normal capacity : 170mAh This Perchlorate warning applies only to primary CR (Manganese Dioxide)
• Continuous standard load : 0.2mA Lithium coin cells in the product sold or distributed ONLY in California USA.
“Perchlorate Material - special handling may apply,
• Operating temperature : -20°C ~ +85°C See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
(-4°F ~ +185°F)
 Connect the power cord into a grounded outlet.

J
 The Mains plug is used as a disconnect device and shall stay readily operable at any time.
 Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
❖ System Shutdown
Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
Please turn off the power using the Power button on the front of your DVR.
After selecting <OK> in the pop-up menu, you can pull off the power cord.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
❖ Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
English _5
overview
CONTENTS
OVERVIEW 3 Important Safety Instructions

5 Before Start
3 8
10
11
Features
Part Names and Functions (Front)
Part Names and Functions (Rear)
12 Remote Control
CONNECTING WITH 13 Installation

OTHER DEVICE 13 Checking the installation environment
14 Connecting the Video, Audio, and Monitor
13 14
15
18
Connecting the USB
Connecting the Camera
Connecting the Alarm Input/Output
19 Connecting the Network
LIVE 21 Getting Started

23 Live Screen Configuration
21 27
29
29
Live Mode
Spot Out
Zoom
30 Audio ON/OFF
30 Freeze
30 Event Monitoring
USING THE DVR 32 System Setup

42 Setting the Device
32 48
51
54
Setting the Recording
Setting the Event
Backup
55 Network Configuration
6_ overview
SEARCH & PLAY 62 Search
65 Playback
62
WEB VIEWER 67 Introducing Web Viewer
68 Connecting Web Viewer
67
 OVERVIEW
69 Using Live Viewer
73 Using Search Viewer
77 Viewer Setup
87 About
87 Mobile Viewer
BACKUP VIEWER 88 SEC Backup Viewer
88
APPENDIX 90 Product Specification (Camera)
92 Product Specification
90 94
97
99
Default Setting
Troubleshooting
Open Source License Report on the Product
English _7
overview
FEATURES
The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 4 channels while simultaneously
supports hard disc recording and playback.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video
and audio data.
• Provides a convenient User Interface
• 4 CH Composite Input Connectors
• Supports CIF(S)/2CIF(M)/4CIF(L) recording formats
• With the network specific codec, network transfer enabled regardless of the recording conditions
• De-interlacing processor for better picture quality
• Display of HDD information and status by using HDD SMART
• Hard Disk overwrite function
• Mass storage hard disk backup through high-speed USB 2.0
• Simultaneous Record and Playback of 4 channel video data
• Various Search Modes (Search by Time, Event, Backup and Motion Detection)
• Various Recording Modes (Time Lapse, Event, Scheduled Recording)
• Alarm Interface
• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer
8_ overview
Standards Approvals
 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
M of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
 OVERVIEW
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Please check the following contents are included in addition to the main unit.
DIGITAL VIDEO RECORDER
POWER REC
DVR Adapter / Power Cable Mouse
SEB-1005R (4EA) SEB-1007R (4EA)

Remote Control / Battery (AAA x 2)
Model : SDE-3003 Model : SDE-3001
SEB-1005R (Bracket 4EA, Screws 12EA) SEB-1007R (Bracket 4EA, Screws 12EA) Camera Cables(4EA), 18.3m (60ft) /
Model : SDE-3003 Model : SDE-3001 Network Cables
User Manual CD,

Network Viewer Software Quick Guide
Quick Connect Program CD
English _9
overview
PART NAMES AND FUNCTIONS (FRONT)
DIGITAL VIDEO RECORDER
POWER REC
bc
Part Names Functions
USB Port Connects the USB devices.
b Remote Control
Receiver
Input the remote control signal.
Power LED : Displays the power ON/OFF status.

c LED Indicator
REC : Lights on when recording is in progress.
10_ overview
PART NAMES AND FUNCTIONS (REAR)
b c
1 2 AUDIO IN
NETWORK
DC 12V
ALARM IN ALARM OUT

1 2 3 4 G 1 COM G
CONSOLE
 OVERVIEW
USB
VIDEO OUT AUDIO OUT VGA
3 4

CAMERA IN Video Signal input ports (UTP type connector).
b VIDEO OUT Video Signal Output Port (RCA jack).
Audio input signal port (RCA jack, CH1).

c AUDIO IN  For SEB-1006R (MIC integrated camera), it is also recommended not to connect other
input devices to the AUDIO IN port.
NETWORK NETWORK connector port.
DC 12V Camera and DVR power input port.
USB USB connector port.
ALARM IN 1~4, G : Alarm Input port.

ALARM OUT 1, COM : Alarm Output port.
VGA VGA Video Signal Output Port.
AUDIO OUT Audio Signal Output Port (RCA jack).
M  If using the VGA cable, the source from VGA will be displayed as main image on the screen along with the OSD
menus. Then, the BNC port will output the video signal alone.
 If not using the VGA cable, the source from BNC will be displayed as main image on the screen along with the OSD
menus. If you connect the VGA cable after the system boot, only the video signal from VGA will be displayed.
English _11
overview
REMOTE CONTROL
SEARCH BACKUP
Displays the search menu. Displays the Backup Menu.
MODE
Changes the screen mode.
DVR
Activates the DVR function.
POWER
Displays the Exit pop up screen.
NUMBER [0~+10]
Used as the numeric input keys, or displays a single
channel.
ID
Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.
Skip Backward (by unit time),
Slow Rewind, Slow Forward,
Skip Forward (by unit time) Move Frame
While paused, moves to the previous/next frame.
FR, STOP, PLAY/PAUSE, FF
T/W
Zooms in or out.
SCROLL ,.
Moves the menu scroll.
MENU RETURN
Goes to the system menu screen. Returns to the previous screen.
Up/Down/Left/Right(▲▼◄ ►)/ENTER
Moves the cursor up/down/left/right, and runs the AUDIO
Select Menu. Turns Audio on/off.
FREEZE
Freezes the screen temporarily. ALARM
Cancels the Alarm.
ZOOM
Runs the digital zoom (x2) function.
REC REC LOCK
Starts or ends the live recording. Selects the recording lock function.
PIP
Selects or deselects the PIP function.
EP10-000522
Using the Numeric buttons

1. Press any button among 1 to 4.
2. Move to the selected channel number.
Changing the Remote Control ID
1. Press the ID button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.
2. Enter 2 digits of your selection in order, while pressing the system [ID] button.
3. When ID input is done, press the system [ID] button again to check the setting.
M  If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.
Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 45)
12_ overview
connecting with other device
INSTALLATION
Please take note of the followings before using this product.
• Do not use the product outdoor.
• Do not spill water or liquid in the connection part of the product.
 CONNECTING WITH OTHER DEVICE

• Do not impose the system to excessive shock or force.
• Do not pull out the power plug forcefully.
• Do not disassemble the product on your own.
• Do not exceed the rated input/output range.
• Use a certified power cord only.
• For the product with an input ground, use a grounded power plug.
CHECKING THE INSTALLATION ENVIRONMENT

Samsung Digital Video Recorder (“DVR” hereinafter) is a Temperature One Year: 24HR X 365 DAY =8,760 HR
Unit: ºC
state-of-art security device, and contains mass storage hard
disk(s) and critical circuits inside.
When the temperature rises inside the product, the product
may breakdown and the product life be shortened.
Life (Unit: HOURS)
English _13
CONNECTING THE VIDEO, AUDIO, AND MONITOR
1 2 AUDIO IN
NETWORK
DC 12V
ALARM IN ALARM OUT

1 2 3 4 G 1 COM G
CONSOLE
USB
3 4
M  Only one mouse port is available.
CONNECTING THE USB

1. By factory default, a USB port is provided for external connection.
2. You can connect a USB HDD, USB memory or mouse to the USB port.
3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >
Storage Device”. (Page 43)
4. This product supports hot-plugging, which connects/removes the USB device during the system operation.
 If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.
J
14_ connecting with other device

CONNECTING THE CAMERA
Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime.
The camera is suitable for both internal and external use.

SEB-1005R SEB-1007R

c

Name Description
Camera Fitting
Groove
Groove that is used to fit the camera bracket.
There are two grooves; one on the top and one on the bottom.
b IR LED These infrared LED's are controlled by the illumination sensor.
c Lens Focal length of 3.6mm enables you to cover relatively longer range of monitoring.
Illumination Sensor Detects incoming light to control the IR LED.
DVR Connection
Cable
Connect the cable directly to the DVR without using a particular power cable.
You can use the RJ-45 cable to connect to a remote camera.
RJ-45 Cable (Length: 18.3m, 60ft)

This cable is specific to UTP connection, which is not compliant with the LAN cable. You can use the UTP
direct cable (all of 8 pins are used) to extend the length to a max of 200m. (based on UTP CAT 5e)
1. CVBS+
2. CVBS-
3. AUDIO
CVBS+ 12V 4. GND
5. 12V
6. N.C
CVBS- GND 7. N.C
N.C GND(AUDIO) 8. N.C
GND 12V
<Cable pin information provided>
English _15
Installing the camera
The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.
1. Select a position where you want to install the
camera.
 Make sure the selected position can sustain the
weight of the camera.
2. Use the screw bolts (M4 X L15) to mount the
camera bracket onto the wall or ceiling.
3. Place the camera on the selected position and fit
the hole either on the top or the bottom of the M4 X L15 sized M4 X L15
screws sized screws
camera into the fixing bolt of the bracket, and
turn the camera clockwise. wall or ceiling
wall or ceiling
 You should be careful when installing the BOX

J camera outdoors because the cable connectors
SEB-1005R SEB-1007R
may be wet with moisture or pile up with impurities.
Camera Bracket
The camera bracket can be used to install the camera on the wall, ceiling or shelf.
Camera Bracket Specification
SEB-1005R SEB-1007R
Description
Name
SEB-1005R SEB-1007R
Use Indoor
Installation Wall or Ceiling
57(W) X 47.2(H) X 100.5(L) mm/ 40(W) X 58(H) X 40(D) mm/

Dimensions
2.25(W) X 1.86(H) X 3.95(L) inch 1.57(W) X 2.28(H) X 1.57(D) inch
Weight 130g(0.29 lbs) 55g (0.12 lbs)
Operating Temperature -10˚C ~ 50˚C (14˚F ~ 122˚F)
Accessories SCREW (M4 X L15) : 3 pcs

Adjusting the Camera Bracket
1. Choose an installation site that can sufficiently support the weight of
the equipments to be installed.
2. Attach the camera bracket to the wall using the supplied screws
(M4 X L15). 4x15 sized screws wall or ceiling.

3. Adjust the camera to target the video location and tighten the
camera bracket handle on the camera bracket. Install the camera
on to the male screw of the camera bracket by rotating the
camera clockwise.
4. Loosen the handle by turning it counter clockwise

and then adjust the camera position. Tighten the
handle, turning it clockwise to lock the camera in
position.
Handle Handle
5. Connect the camera cable to the camera.
English _17
CONNECTING THE ALARM INPUT/OUTPUT
Connecting the alarm input signal IN

NETWORK
DC 12V
Connection port for the alarm input signal. ALARM IN ALARM OUT
1 2 3 4 G 1 COM G
CONSOLE
Connect one strand of the sensor signal line (four strands) to UT VGA
USB
the alarm input port and connect the other to the [G] port.
Connecting the alarm output signal

ALARM IN
ALARM IN
ALARM OUT
ALARM OUT
Connection port for the alarm output signal. 1 1 2 2 33 44 GG G1 COM
1 COMG
Connect one strand of the sensor signal line to the alarm
output port and connect the other to the [COM] port.
• ALARM IN : 5mA sink
• ALARM OUT : 24V DC 1A, 125VAC/0.5A

CONNECTING THE NETWORK
Connecting to Network through Ethernet (10/100BaseT)
1 2 AUDIO IN
NETWORK
DC 12V
ALARM IN ALARM OUT

1 2 3 4 G 1 COM G
CONSOLE
USB

3 4
RJ-45 Ethernet Cable

(Direct Cable)
NETWORK
Back Bone
Hub/Switcher
Windows
Network Viewer
Hub/Switcher
Connecting to the Network using the router
1 2 AUDIO IN
NETWORK
DC 12V
ALARM IN ALARM OUT

1 2 3 4 G 1 COM G
CONSOLE
USB
3 4
NETWORK
xDSL or Cable xDSL or Cable
Broadband Router Modem Modem
External Remote PC
DDNS Server
(Data Center)
English _19
Connecting to Internet through ADSL
1 2 AUDIO IN
NETWORK
DC 12V
ALARM IN ALARM OUT

1 2 3 4 G 1 COM G
CONSOLE
USB
3 4
RJ-45 Ethernet Cable

(Direct Cable)
INTERNET
Phone(ADSL) Line ADSL MODEM
Windows
Network Viewer
Hub/Switcher

live
GETTING STARTED
Starting the system
1. Connect the power cable of the DVR to the wall outlet.
 LIVE
M  It takes about 10 seconds to display the start screen after
booting.
2. You will see the initialization screen.

The initialization process will last about 1 minute.
If a new HDD is installed, the initialization process may take
REC
longer.
3. The live screen appears with a beep.

2011-01-01 01:10:25
2011-01-01
01:10:25
Shutting Down the System

You can shut down the system only if you have logged into the DVR.
You require permission to shut down the system if you are not logged in as admin.
1. Press the [POWER] button on the remote control or
2011-01-01 01:10:25
right-click to display the context sensitive menu and select
<Shutdown>.
2. The “Shutdown” confirmation window appears. Shutdown
3. Use the arrow keys on the remote control to move to Are you sure to shutdown?
OK Cancel
<OK> and press the [ENTER] button or click <OK>.
The system will shut down.
4. Disconnecting the power cable for power off and
reconnecting the power cable to restart.
M  For the permission management, refer to “Permission Management > Setting Permissions”. (Page 37)
English _21
live
Login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen. Scene Mode 
2011-01-01 01:10:25
You will see the context sensitive menu as in the right Spot Out
Audio Off

figure. Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Login
2. Click <Login>.
2011-01-01 01:10:25
The login dialog appears.
You can also see the login dialog to access a desired menu
by pressing the [MENU] button on the remote control.
Login
 The login dialog will also appear if you press a menu button on  ID admin
the remote control of the DVR when the corresponding menu  Password
OK Cancel
requires logging in.
 After logged in, press [RETURN] on the remote control to display
the logout dialog.
 By default, initial ID and password are set to “admin”, and
“4321”.
 The default password can be exposed to a hacking thread so it is recommended to change the password after
J installing the product.
M  For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 37)
Locking All Buttons

This will restrict access to all buttons available in the DVR.
1. In Live mode, press buttons in the order of [STOP (@)]
2011-01-01 01:10:25
[FREEZE][STOP (@)][FREEZE][MENU].
All buttons will be locked.
2. In the lock condition, press any button to display a dialog Key Lock Password
where you are prompted to enter the password for  ID

 Password
admin
unlocking the buttons. OK Cancel
The button lock will be released if you enter the admin

password.
22_ live
LIVE SCREEN CONFIGURATION
Icons on the Live Screen
You can check the status or operation of the DVR with the icons on the live screen.
2011-01-01 00:00:01
 LIVE
CAM 01
Name Description
Current Date, Time Displays the current time and date.
b Login Information When you are logged in, the “LOG ON” icon will be displayed.
Displayed if the zoom function is activated.
Displayed if you press the Pause button.
c
Displayed in Auto Sequence mode where all channels are switched at the
Screen Mode specific time interval.
This icon is displayed if a user with restricted access to the Record button tries
to make manual recording.
 Only the user with the applicable permission can release (stop) the recording.
Displayed if the HDD is full and the DVR has an insufficient space to record.
Displayed if no HDD is installed or the existing HDD should be replaced.
System Operation Displayed if the HDD needs a technical examination.
This will be displayed if the backup operation is in process.
Displayed if a new firmware is found from the network.
Displayed if no input is entered in the condition that the camera is set to <ON>.
Video Input Status
Nothing will be displayed on the screen if the camera is set to <OFF>.
Camera Name/ Channel Displays the camera name and the changed channel, if any.
Displays the resolution of the recording screen. (Page 49)

Displays AUDIO ON/MUTE.
Not displayed in video mode if deactivated.
Camera Operation
If the sensor is set to <ON>, the input signal will be displayed on the screen of
the connected channel.
Displayed if a motion detected in the condition that the motion detection is set to
<ON>.
Displays the current record mode from Record/Event/Schedule.
English _23
live
Error Information
• If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem,
you will see the “HDD FAIL”( ) message in the top left corner. In this case, make sure you contact the
service center for assistance as this may cause a failure of recording, playback or backup.
M  If you see the No HDD, HDD FAIL icons on the screen, contact the service center for more details.
Live Screen Menu

In addition to the buttons the remote control, you can access a desired menu by right-clicking the mouse any
area in live mode.
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/
logout, screen split mode and DVD operation mode.
M  Menu items of Search, Record, Backup, Shutdown can be deactivated, depending on the user permission.
Scene Mode 
2011-01-01 01:10:25 2011-01-01 01:10:25
Scene Mode 
Spot Out 
Spot Out 
Audio Off Zoom In
Freeze Audio
Stop Alarm Freeze
Record Stop Alarm
Play Record
Search Play
Backup Search
Main Menu Backup
Shutdown Main Menu
Hide Launcher Shutdown
Logout Hide Launcher

Logout
< Split Mode Menu > < Single Mode Menu >
Split Mode Menu

The context sensitive menu in split mode differs, depending on the login/logout status.
1 Scene Mode 
2011-01-01 01:10:25
2 Spot Out 
3 Audio Off
4 Freeze
5 Stop Alarm
6 Record
7 Play
8 Search
9 Backup
10 Main Menu
11 Shutdown
12 Hide Launcher
13 Logout
24_ live
Menu Description
Scene Mode Refer to “Live Mode”. (Page 27)
b Spot Out Refer to “Spot Out”. (Page 29)
c Audio On/Off Refer to “Audio ON/OFF”. (Page 30)
Freeze Refer to “Freeze”. (Page 30)
 LIVE
Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 30)
Record/Stop Starts/stops the standard recording.
Play Refer to “Search & Play > Play”. (Page 65)
Search Refer to “Search & Play > Search”. (Page 62)
Backup Refer to “Using the DVR > Setting the Backup”. (Page 54)
Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 32)

Shutdown Turns down the DVR.
Show/Hide Launcher Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 26)
m Login/Logout You can log in or out.
Single Mode Menu

The single mode menu is available only in Single Mode.
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.
2011-01-01 01:10:25
1 Full Screen
Spot Out 
2 Zoom In
Audio
Freeze
Stop Alarm
Record
Play
Shutdown
Hide Launcher
Logout
Menu Description
Full Screen
Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.
b Zoom In Enlarges the selected image. (Page 29)
English _25
live
View the Launcher Menu
The Launcher menu appears on the bottom of the live screen.
1. In Live mode, right-click to display the context menu and
2011-01-01 01:10:25
select <Show Launcher>.
2. Move the cursor to the bottom and click a desired item in
the Launcher menu.
M  If no input is entered for 10 seconds, the menu will disappear.

 The Launcher menu can be accessed only by using the mouse.
2011-01-01
01:10:25
2011-01-01
01:10:25
2011-01-01 Alarm Freeze

01:10:25
Menu Description
Displays the current time and date.

Date/Time The indication of AM/PM is displayed if you set 12 hours for the time format in
“System > Date/Time/Language > Time”. (Page 32)
b Screen Mode Press this button to switch the screen mode in sequence.
c Menu Expansion Button Click to display the hidden menu to the right.
Audio Turns ON/MUTE the sound of the selected channel.
Zoom Enlarges the selected area. This is available only in Single Live mode.
Alarm Stops the alarm if it's activated.
Freeze Freezes the Live screen temporarily.
Play Enters Play mode if a file to play exist, and if not, enters Search mode.
Record Start/End recording the Live screen.
26_ live
LIVE MODE
Displays 4 live video images in 3 different modes.
Switching the screen mode

To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the remote control to switch the mode in the sequence of the launcher menu
 LIVE
items.
CH1 CH2

CH2
CH3 CH4 CH1 CH1
4-split mode PIP Auto Sequence
Switching the screen automatically
With SDE-3001/3003 you can display 4 live single screens in sequence.
CH1 4
CH1
CH1
CH1
Single mode 1
M  In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be
conducted at the set interval. (Page 42)
English _27
live
Channel Setting
You can display the channel in a desired area of a split screen.
1. Click a camera name to display a channel list where you can select a different channel.
2. Select a desired channel and click it.
The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
change the channel position.
 Ex : if switching CH 1 to CH 4

CH1 CH2 CH4 CH2
CH3 CH4 CH3 CH1
Switching to Single Mode

When in split mode, select and double-click a desired channel to switch to its Single mode.
Press the number corresponding to a desired channel the remote control to switch to its Single mode.
Refer to “Remote Control > Using the numeric buttons”. (Page 12)
 Ex : If double-clicking CH 3 or pressing the number “3” on the remote control.

CH1 CH2
CH3 CH4 CH3
28_ live
SPOT OUT
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out
port.
Selecting a Spot Out mode

If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you
can select a output screen mode.
 LIVE
1. In Live mode, right-click any area on the screen. Scene Mode 
2011-01-01 01:10:25
The Live menu appears. Spot Out  Auto Sequence
Audio Off CH1
Freeze CH2
2. Click Spot Out. Stop Alarm CH3
CH4
Record
Supports the Spot output in Single screen with Auto Play
Sequence mode. Search

Backup
 The Spot output is supported only for a designated channel. Main Menu
Shutdown
For the Spot Out port of a model, refer to “Part Names and Hide Launcher
Logout
Functions (Rear)”. (Page 11)
<M
Multichannel
lti h l Li
Live M
Menu >
ZOOM
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.
1. Select <Zoom In> in the right-click menu.
Press the [ZOOM] button on the remote control, or simply click < > in the launcher menu. The zoom
box appears.
2. Use the direction keys, or drag and drop to specify an area to enlarge.
3. Press the [ENTER] button, or double-click the selected area to enlarge it twice.
 In the enlarged image, use the direction buttons (◄ ►) on the remote controlto move the enlarged area.
4. Press the [ZOOM] button on the remote control, or simply click < > in the launcher menu to release
the zoom.
2011-01-01 01:10:25
English _29
live
AUDIO ON/OFF
You can turn the sound on/off corresponding to the channel in Live mode.
AUDIO ON/OFF in Single mode

Click the audio icon ( ) on the screen, or press the [AUDIO] button on the remote control to turn it on/off.
M  Only the channel where <AUDIO> is set to <ON> in “Device > Camera” displays the audio icon (
that you can use to turn the sound on/off.
) in Live mode
FREEZE
This is available only in Live mode, this pauses playing the Live image temporarily.
1. Press the [FREEZE] button the remote control, or click < Freeze > in the launcher menu.
The playback of the image is stopped temporarily.
2. Press the [FREEZE] button again, or click < Freeze >.
This will release the freeze.
EVENT MONITORING
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 46)
• If multiple events occur simultaneously, the screen will switch to a split mode.
- 2~4 events : 4-split mode
• If the second event occurs within the set time of <Event Display>, the first event will last until the second
one is terminated. (Page 46)
 Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
Event occurrence 5 seconds
Stop alarm
CH1
30_ live
 Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred in CH 1.
Event occurrence 4 seconds 9 seconds
Stop alarm
 LIVE
CH1 CH2
CH1
M  Press the [ALARM] button to reset the alarm settings and to release the event mode.
 If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will
be performed.
English _31
using the DVR
You can setup the system properties, devices, and options for recording, event,
backup and network.
SYSTEM SETUP
You can setup Date/Time/Language, Permission, System Properties and Log.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.
Setting the Date/Time/Language

Set the Date/Time/Language
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control.
2011-01-01 01:10:25
 If not logged in, it prompts with login window.
Refer to “Login”. (Page 22)
2011-01-01
01:10:25
2. Use the left/right buttons (◄ ►) to select the <System>.

Logout Return
System property setup menu is selected.
3. Use the up/down buttons () to select <Date/Time/
Language> and press the [ENTER] button. System
4. Select <Date/Time/Language>. Date/Time/Language

A dialog to setup Date, Time and Language. Permission Management
System Management
5. Use direction buttons (◄ ►) to select an item to set Log Information
and make your changes.
• Date : Sets the date that will appear on the screen. Date/Time/Language
You can select the date format. Date/Time/Language Holiday
• Time : Sets the time and its format that will appear on the  Date 2011-01-01 YYYY-MM-DD
screen.
Select either one from <24 Hours, 12 Hours (AM/PM)>.  Time
 Time Zone
08:14:24
GMT+09:00
24 Hours
• Time Zone : Sets the time zone of your area based on the  Time Sync. Setup
 DST Dec First (Sun) 0 Dec First (Sun) 0
Greenwich Mean Time (GMT).
 GMT (Greenwich Mean Time) is standard World Time and the basis  Language English
of world time zone. OK Cancel
• Time Sync. : You can set the DVR’s current time

synchronized to a selected <Time Server> regularly if you select to use <Time Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.
32_ using the DVR

- Time Server : Enter an IP or URL address of the time
Date/Time/Language
server. Date/Time/Language Holiday
- Last Sync Time : Displays the most recent
 Date 2011 -01-01
Time Synchronization Setup YYYY-MM-DD
synchronization time from the selected time server.
 Synchronization
- Activate as Server : Set to <Use> to allow the DVR to act  Time
 Time Server
08:14:24
Use
24 Hours
203.248.240.103
 Time Zone GMT+08:00
as a Time Server for other DVRs.  Last Sync Time
 Time Sync. Setup Not Used
Fail
• DST : Set up Daylight Saving Time with its period to make

 Activate as Server Use
 DST Dec First (Sun) 0H Dec First (Sun) 0H
OK Cancel
the time earlier than the GMT of its time zone by 1 hour  Language English
during the set period.

• Language : Select your language. Sets the language for the OK Cancel
 USING THE DVR

interface.
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,
Turkish, Czech, Danish, Swedish, Thai, Romanian, Serbian, Croatian, Hungarian and Greek are available.
6. When the Date/Time/Language setup is done, press <OK>.
M  You can also use numeric buttons on the remote control to enter values for Date, Time and other numeric fields.
Setting Holiday
You can set specific dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.
1. Use the up/down buttons () in <Date/Time/Language> window to select <Date/Time/Language>, and
press the [ENTER] button.
2. Select <Holiday>. Date/Time/Language
A calendar for Holiday setup appears. Date/Time/Language Holiday
3. Use the left/right < > buttons to select year or month, 2011 Jan
and press the [ENTER] button. Sun Mon Tue Wed Thu Fri Sat
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30 31
OK Cancel
4. Use direction buttons (◄ ►) to select a desired date,

Date/Time/Language
and press the [ENTER] button. Date/Time/Language Holiday
You will see the “Setting Holiday” screen.
2011 Jan
 Ex : Select January 10th and check on <1/10> only to make Setting
Sun Holiday
Mon Tue Wed Thu Fri Sat
every January 10th a holiday. Check both on <1/10> and <Jan 2 3

1 / 10
4 5 6 7 8
1
2nd Mon> to make every January 10th and 2nd Monday of 9 10

Jan 2nd Mon
11 12 13 14 15
OK Cancel
January holidays. 16
23
17
24
18
25
19
26
20
27
21
28
22
29
30 31
5. When the Holiday setup is done, press <OK>.
OK Cancel
Using the Calendar

Select year and month.
Select the left/right < > key on the left/right side of year/month and press [ENTER] button to
adjust by 1 year/month.
 Use direction buttons to select a date and press [ENTER] button.
 A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event
Search.
English _33
using the DVR
Permission Management
You can set permissions of each user over the DVR's specific function and settings.
Setting the Administrator

You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.
1. Use the up/down buttons () in <System> window to Permission Management
move to <Permission Management>, and press Admin Group User Setup
[ENTER] button.
 ID admin
2. Select <Admin>.  New Password ************
A dialog for Admin ID and Password input appears.  Confirm P/W ************
3. Use direction buttons (◄ ►) to move to a desired

item, and set the ID and password.
 By default, initial ID and password are set to “admin”, and

M “4321”.
OK Cancel
 The default password can be exposed to a hacking thread so it iis recommended

d d tto change
h th
the passwordd after
ft
installing the product.
4. When the administrator setup is done, press <OK>.
Using Virtual Keyboard

 For alphanumeric inputs, the virtual keyboard window
appears.

 Use direction buttons (◄ ►) to move to a desired q
` 1
w
2
e
3
r
4
t
5
y
6
u
7
i
8
o
9
p
0
[
-
]
=
\ Del
character, and press the [ENTER] button. a s d f g h j k l ; ‘ Caps Lock
z x c v b n m , . / Shift
 In the upper text input box of the virtual keyboard, there Space Ctrl
displays a list of candidate words containing the selected OK Cancel
character.
 Select a word from the list, or use the keyboard to enter the
whole word.
 If there are many of candidate words, use < , > buttons to move between them forward and backward.
 Select <OK>.
Entered word is applied.
 For upper case letters, use <Caps Lock> button.
 For special characters, use <Shift> button.
 Using the virtual keyboard is the same to a normal keyboard use in your region.
 You can enter the ID with case-insensitive alphanumeric characters only.
 For the password, use alphabets and special characters excluding < \ > and <“>.
 You can use number buttons on the remote control.
34_ using the DVR

Setting the Group
You can create user groups and setup permissions for those user groups.
You can register a user for each group in <User>.
1. Use the up/down buttons () in <System> window to
[ENTER] button.  Group Add Delete Rename
Group Authority
2. Select <Group>. Live View Setup
 USING THE DVR

A window for <Add>, <Delete>, <Rename>, and Search
Backup
Setup
Setup
<Group Authority> setup appears.

item, and set the value.
OK Cancel
• Add, Delete, Rename : You can add, delete, rename a
group or modify the permissions given to the group.
The virtual keyboard appears when <Add> or <Rename> was selected.
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10
groups.
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts
belonging to that group.
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.
 For entering a group name, refer to “Using Virtual Keyboard”. (Page 34)
• Group Authority : Sets permissions to access menu items of each group.
Users of a group can access checked functions.
4. When the group setup is done, press <OK>.
To set the group authority

You can set the permissions of the group users to access the menu according to the channel.
1. Select a menu to which the group permission is assigned. Permission Management
The menu where the group permission is assigned will be Admin Group User Setup
displayed in the Live menu when a group user logs in.  Group ABC Add Delete Rename
Group Authority
Channel Setup
• Live View : You can set the permission to access the Live Live View
All
Setup
Search Setup
screen according to the channel. Backup
1
Setup
2 3 4
• Search : You can set the permission to access the Search

menu according to the channel. OK Cancel
• Backup : You can set the permission to access the Backup

OK Cancel
menu according to the channel.
2. Select <OK>.
Select and assign a group user so that the user can access the specified menu.
English _35
using the DVR
To restrict the user permissions
If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.
1. Start the DVR.
If all permissions are restricted, only the Login dialog
should appear.
2. Log in with a registered user ID. Login
 ID abc
 Password
OK Cancel
3. Right-click any area on the screen.

2011-01-01 01:10:25
If all permissions are restricted, only the accessible context
menus should appear.
Scene Mode 
Audio Off
Freeze
Stop Alarm
User Menu
Hide Launcher
Logout
2011-01-01
01:10:25
To change the user password

If you log in with a user account that is restricted to access the menu, you can change your own password
only.
1. Log in with your account. Permission Management
User
2. Select <User Menu>.
The Permission Management setup screen appears.  ID abc
 New Password ************

3. Select <Permission Management>.  Confirm P/W ************
The Password setup dialog appears.

4. Enter a new password.
5. Select <OK>.
You change to the password will be applied. OK Cancel
36_ using the DVR

Setting the User
Users can be added only if a group was created in <Group> menu.
[ENTER] button.  Group All Group Add
Group Name ID Viewer Delete

2. Select <User>.
A window for Add User appears.
 USING THE DVR

3. Use direction buttons (◄ ►) to select <Add> from the
window.
A window for “Add User” appears. Previous/Next Page
You can configure the Network Viewer settings including OK Cancel
name, ID, viewer, Select Group and password.

Result of the user setup appears in the <User> window.
To change the user property, use “Edit User”.
The “Edit User” window appears when you select a Admin Group User Setup
desired item to be changed in the <User> window.  Group Add User
All Group Add
Group  Name Name ID Viewer Delete

• Viewer : If you select <Use>, you will be given access to the  ID
 Viewer Not Used
Web Viewer and Network Viewer.  Select Group ABC
 Refer to “Connecting Web Viewer”. (Page 68)

 Password
 Confirm P/W
OK Cancel
 For more information about use of Network Viewer, refer to the Previous/Next Page
Network Viewer's user guide. (Page 9) OK Cancel
4. When the user setup is done, press <OK>.
Setting Permissions
You can set restricted access for all general users.
Items with restrictions will require logging in for use.
1. Use the up/down buttons () in <System> window to Permission Management
[ENTER] button. Restricted Access
Live View Backup All
2. Select <Setup>. Restriction on Network Access
The Restricted Access, Restriction on Network Access, All Network Web Viewer
 Auto Log out

Auto Log out, Manual Input of ID setup screen appear.  Manual Input of ID
OFF
ON

OK Cancel
• Restricted Access : All menu items allowed for a user can
be set with restricted access.
- Checked ( ) : Restricted
- Not checked ( ) : Accessible
 If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>
setting.
 If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group
Authority> setting.
• Restriction on Network Access : Restricts remote access from a <Restricted Access> network.
- All Network : Restricts all access instances via Network Viewer and Web Viewer.
- Web Viewer : Restricts access via the Web Viewer.
• Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of
time.
English _37
using the DVR
• Manual Input of ID : Prompts you to enter the user ID
manually for the login process.
- Checked ( ) : Encloses the registered user IDs with the
[] symbols. Login
Use the virtual keyboard to enter the user ID.  ID *****
 Password
4. When the permission setup is done, press <OK>. OK Cancel
System Management
You can check the system version, update to a newer version, as well as data backup and initialization.
Checking the System Information

You can check the current system version, broadcasting system, MAC address. You can update the system.
1. Use the up/down buttons () in <System> window to System Management
move to <System Management>, and press [ENTER] System Information Settings
button. System Information

 Software Version v1.0xh_yymmddhhmmss
2. Check the Version, Broadcast Format, and MAC Address.  Broadcast Format NTSC
 MAC Address 00:00:F0:54:FF:FF
• System Information : Shows the current system’s S/W Upgrade

 Device No Device Upgrade
information.  Version No S/W Data
The values can not be changed by a user.

• S/W Upgrade : Updates the DVR’s software.
Previous
 Ex : If you connect to a storage device that has upgradable software System Management
installed, and return to the <System Management> menu, the System Information Settings
current software version will be displayed. System Information

 Broadcast Format NTSC
S/W Upgrade
 Device USB2FlashStorage Upgrade
 Version v1.0xh_yymmddhhmmss
Previous
38_ using the DVR

• Updating the Software
1. Connect a device storing the software to be updated. System Management
(It may take about 10 seconds to recognize the device.) System Information Settings
 Upgradeable devices include USB memory and network device. System Information
System Upgrade
 To update the network, the current DVR should have been
 Broadcast Format NTSC
 MAC Address
Current Version 00:00:F0:54:FF:FF
v1.0xh_yymmddhhmmss
connected to the network. New Version

S/W Upgrade
Do you want to upgrade?
v1.0xh_yymmddhhmmss
 Device Upgrade
Upgrade via the proxy server may not be enabled due to the  Version
USB2FlashStorage
OK
V1.08_090731170402
Cancel
restricted access.
 USING THE DVR

2. Select <System Management> from <System> window. Previous
3. Select <System Information>.

4. When the recognized device appears, select <Upgrade>.
 The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is
same to or older than that of <S/W Upgrade>.
5. Press <OK> in the “System Upgrade” window.

System Management
 While updating, it shows the progress. System Information Settings
System Information
• Updating progresses with 3 steps as shown in the figure.  Software Version v1.0xh_yymmddhhmmss
 BroadcastS/W
Format NTSC
Upgrade
Software upgrading...
S/W Upgrade
 Version V1.08_090731170402
Previous
System Management
System Information Settings
System Information
 BroadcastS/W
FormatUpgrade
NTSC

S/W Upgrade
Do not turn off during the upgrade.
 Version V1.08_090731170402
Previous
6. When the updating is done, it automatically restarts.

Do not turn the power off until it finishes restarting.
M  If “Upgrade Failed” appears, retry from the step 4.

When you experience continued failure, consult the service
center for assistance.
 When you perform S/W update remotely using Smart Viewer,
it may take a max of 3 minutes to complete the update since
Smart Viewer popped up a confirmation message. This is to
guarantee that the DVR set operates stably. For a faster
update, use the USB cable to connect to the DVR set.
English _39
using the DVR
Settings
You can copy and import the DVR settings by using a storage media.
System Management
move to <System Management>, and press [ENTER] System Information Settings
button.
 Storage Device 0 MB (Remained Capacity)
2. Select <Settings>.  DVRUSB

 USBDVR
10041400
No data
Export
Import
A window of storage device and load factory default Include Network Settings
appears.  Load Factory Default Default

item, and export or import settings data to a storage
device. Previous
• Storage Device : Shows the connected storage device.

• Export : Exports DVR settings to the connected storage device.
• Import : Imports DVR settings from the storage device and applies to the DVR.
 If <Include Network Settings> is checked, the network settings will be imported too.
• Load Factory Default : If <Default> is selected, a System Management

confirmation dialog for “Load Factory Default” prompts. System Information Settings
Press <OK> to initialize the system to the factory default.
 Storage Device 0 MB (Remained Capacity)
Load
 DVRUSB Factory Default
4. To move to the previous menu, press <Previous>.  USBDVR
10041400
No data
Export
Import
Sure to Default Setting?
Include Network Settings
 Load Factory Default OK

Default Cancel
Previous
Log Information
You can browse logs on the system and events.
System Log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
Log Information
move to <Log Information>, and press [ENTER] button. System Log Event Log Backup Log
2. Select <System Log>. Search Day
First Page
2011-01-01
Last Page
Search
Type View all
 Refer to “Using the Calendar”. (Page 33) No. Log List Date/Time
Click on the calendar < > to display the calendar window.

• Type : When there are too many logs, you can display logs of
the desired format by selecting the type. Previous/Next Page
3. Use direction buttons (◄ ►) to move to a desired item, Previous
and press <Search>.
40_ using the DVR

Event Log
Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.
Log Information
move to <Log Information>, and press [ENTER] button. System Log Event Log Backup Log
2. Select <Event Log>. Search Day
First Page
2011-01-01
Last Page CH
Search
All CHs Type View all
3. Use direction buttons (◄ ►) to move to the desired No. Log List Date/Time
 USING THE DVR

7 Motion Detection [CH 1] 2011-01-01 00:02:14
item. 6
5
Motion Detection [CH 2]
2011-01-01 00:02:14
2011-01-01 00:02:14
4 Motion Detection [CH 4] 2011-01-01 00:02:18
4. Set Search Day, Channel and Type and the press 3

2
2011-01-01 00:02:18
2011-01-01 00:02:18
<Search>. 1 Motion Detection [CH 1] 2011-01-01 00:02:18
Previous/Next Page
 Refer to “Using the Calendar”. (Page 33) Previous
Click on the calendar < > to display the calendar window.
Backup Log
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).
1. In the <System> window, press the up/down () button Log Information
to move to <Log Information> and press the [ENTER] System Log Event Log Backup Log
button. Search Day 2011-01-01 ~ 2011-01-02 Search
First Page Last Page Previous/Next Page
2. Select <Backup Log>. No. User Date/Time
3. Use the four direction buttons (◄ ►) to move to a

desired item.
4. Specify a search term and select <Search> in the right
corner. Previous
Backup details for the search term will be listed.
English _41
using the DVR
SETTING THE DEVICE
You can setup Camera, Storage Device, Remote Device and Monitor.
Camera
Setting the Camera

You can set Video, Audio, Channel Name and Dwell Time of a Camera.
Logout Return
2. Use the left/right button (◄ ►) to select <Device>.

Device setting menu is selected.
Device
3. Use the up/down buttons () to move to <Camera>,
and press [ENTER] button. Camera
Storage Device
Remote Device
Monitor
4. Select <Camera>. Camera

You will see a window where you can configure the Camera
camera settings including Video, Audio, CH Name, SEQ- CH Video  Audio  CH Name SEQ-Dwell Time 
  
Dwell Time. 1
2
ON
ON 
OFF
OFF 
CAM 01
CAM 02
5 sec
5 sec 
3 ON  OFF  CAM 03 5 sec 
5. Use direction buttons (◄ ►) to move to a desired 4 ON  OFF  CAM 04 5 sec 
• Video Screen Setup
- <ON/OFF> : You can turn ON/OFF the selected OK Cancel
channel’s camera.
- <Covert1> : Shows information other than the video of the selected channel.
 For privacy protection, it does not display the video while the recording continues.
- <Covert2> : Shows nothing but an empty screen while the recording continues.
• Audio
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.
- For SEB-1006R (MIC integrated camera), you must connect it to CH1 and set CH1 Audio to “ON” in the
Camera menu.
 Audio output is available for only CH1.
42_ using the DVR

• CH Name : Up to 15 characters including blanks are allowed. (The first character should not be empty.)
 Refer to “Using Virtual Keyboard”. (Page 34)
• SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.
 If set to <OFF>, the channel is not listed in the Auto Sequence mode.
• Screen Setup : The video appeared on the screen may vary

depending on the channel’s camera, configure the DVR display
to your preferences.
Select a channel and adjust the < (Brightness)>,
 USING THE DVR

< (Contrast)>, and < (Color)> of the selected channel.
• Press the <Init> to initialize settings back to the default 50.
6. When the camera setup is done, press <OK>. Screen Setup
CH1 50 50 50 Init Apply to All CH
OK Cancel
Storage Device
You can check information on storage devices.
Confirming Devices
You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD).
1. Use the up/down buttons () in <Device> window to Storage Device
move to <Storage Device>, and press [ENTER] button. Device Format HDD Alarm
2. Select <Device>. Device

HDD
No.
1
Used/Total
12.28G/499.37G
Used
Internal
Status/Management
Normal
• No. : Shows the assigned number of the internal HDD.

• Used/Total : Shows the used/total capacity of the storage
device.
• Used : Sets the storage device’s usage. HDD Map
- USB memory is used for backup purpose only. OK Cancel
• Status/Management : Shows the current status of the HDD,

as in Normal/Check/Replace.
- Normal : Available to use
- Check : Available to use but recommended to replace
- Replace : Requires immediate replacement.
3. To move to the previous menu, press <OK>.
English _43
using the DVR
Formatting
You can format a storage device.
2. Select <Format>. Device Select Used/Total Used

HDD 1 12.28G/499.37G Internal
A window for selection of device for formatting appears.
3. Use direction buttons (◄ ►) to select a device to be
formatted.
Format
OK Cancel
4. Select <Format> on the bottom of the screen. Storage Device

Press <OK> on the “Manage” confirmation window will Device Format HDD Alarm
start formatting the selected device. Device Select Used/Total Used

HDD 1 12.28G/499.37G Internal
5. When the formatting is done, press <OK>. Manage
Formatting deletes all recordings.
M  Even when formatted, used HDD space will not be 0 GB due

Proceed formatting?
OK Cancel
to the space reserved by the system required for operating.

Format
OK Cancel
44_ using the DVR

HDD Alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
2. Select <HDD Alarm>.  Check Alarm Output Port 1 BEEP

All
A window for setting HDD check and replace output ports  Duration OFF
 USING THE DVR

and their durations appears.
 Replace Alarm Output Port 1 BEEP
3. Use direction buttons (◄ ►) to move to the desired  Duration

All
OFF
item.
• Alarm OK Cancel
- Alarm signal will output through the alarm out port on the
rear side when selected <1>.
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
• Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm
output port.
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
• Duration : Sets the alarm duration for the alarm signal and beep sound.
M  <Check> status means that the HDD is operating but it has problems that require technical examination.
( ) appears on the Live screen.
 <Replace> status means that the HDD has defect and requires immediate replacement.
( ) appears on the Live screen.
4. When the HDD Alarm setup is done, press <OK>.
Remote Devices
Specify the use of remote control and the remote control ID so that you can synchronize with the DVR.
1. Use the up/down buttons () in <Device> window to
Remote Device
move to <Remote Device>, and press [ENTER] button.
Remote Control ON ID 00
2. Make sure to match IDs of the DVR, Remote Control and
press <OK>.
M  For changing the remote control’s ID, refer to “Changing the

Remote Control ID”. (Page 12)
OK Cancel
English _45
using the DVR
Monitor
You can select which item(s) to be displayed on the screen.
Setting the Monitor

1. Use the up/down buttons () in <Device> window to Monitor
move to <Monitor>, and press [ENTER] button. Monitor Spot Out Mode
2. Select <Monitor>.  Event Display OFF
 Display Date Time CH Name Icon

• Event Display : Sets the dwell time of the event channel
display on the monitor when an event occurs.
Display Position Setup
If selected <Continuous>, it displays the channel until you
OK Cancel
press [ALARM] button to release it.
• Display : Displays only checked items on the monitor
screen.
4. When the monitor setup is done, press <OK>.
Setting Display position

Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,
depending on the condition. Then, you can change the display position of the data.
1. In the <Device> window, press the up/down () button to move to <Monitor> and press the [ENTER]
button.
2. Select the <Monitor> item.
3. Select <Display Position Setup> in the bottom.
2011-01-01 01:10:25
You will move to the <Display Position Setup> window.
4. Use the four direction buttons or the number buttons on Display Position Setup
the remote control to adjust the data position. 30
30 30
30
OK Cancel
46_ using the DVR

Setting the Spot Out
You can set the DVR to output information / video apart from the monitor out.
Monitor
2. Select <Spot Out>.  Spot Out 1 SEQ Set Mode All
 The number of Spot Out terminals differs according to the  Event Display OFF
model.
 USING THE DVR

OK Cancel
• Spot Out 1 : You can select between Auto Sequence, and

Monitor
Single. Monitor Spot Out Mode
• Set Mode : A window for “Set Spot Out” appears and you  Spot Out 1 SEQ
Set Spot Out
Set Mode All
can set the channel for it.  Event Display OFF
You can set the dwell time between the screen switching in 1 2 3 4
“Setting the Device > Camera > SEQ-Dwell Time”.

(Page 43) OK
M  You can setup using the mouse right button in Live screen. OK Cancel
Refer to “Spot Out”. (Page 29)
4. When the Spot Out is done, press <OK>.
Setting the Screen Mode

You can configure the Live screen and Split Screens.
Monitor
Live Screen
2. Select <Mode>.
3. Use direction buttons (◄ ►) to move to a desired Play Screen

• Live Screen : Select split modes for the Live screen. Live Play
4-split screens are included by default.

• Play Screen : Select split modes for the playback screen. OK Cancel
Single screen and 4-split screen are provided by default.

4. When the screen mode setup is done, press <OK>.
English _47
using the DVR
SETTING THE RECORDING
You can setup scheduled recording, event recording and other recording related settings.
Recording Schedule
Make your reservation on a date and time to schedule the recording on specified time.
Logout Return
2. Use the left/right button (◄ ►) to select <Record>.

Record menu is selected.
3. Use the up/down buttons () to move to <Recording Record
Schedule>, and press [ENTER] button. Recording Schedule

Event Record Duration
REC Quality & Resolution
Record Option
4. Select <Recording Schedule>. Recording Schedule

A window of scheduled recording setup appears. CH1
5. Use direction buttons (◄ ►) to move to a desired All 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Sun
item, and set the value. Mon

Tue
Wed
Thu
Fri
Sat
Hol
No Recording Continuous Event Apply to All CH

Both(Cont&Evnt)
OK Cancel
• Apply to All CH : If selected <Apply to All CH>, “Apply to Recording Schedule

All CH” window appears. CH1
Press <OK> to apply the setup to all channels. All 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon Apply to All CH
6. When the recording schedule setup is done, press <OK>. Tue
Wed
Apply recording schedule to all channels?
Thu
Fri
Sat OK Cancel
Hol
No Recording Continuous Event Apply to All CH

Both(Cont&Evnt)
OK Cancel
48_ using the DVR

Recording Color Tags
Color Function Description
White No Recording No schedule / event recording
Orange Continuous Scheduled recording only
Blue Event Event recording only
Green Both(Cont&Evnt) Both scheduled / event recordings
 USING THE DVR

Each press of a selected cell will cycle through <No Recording>-<Continuous>-<Event>-
<Both(Cont&Evnt)>.

You can set the beginning and ending point of a recording on an event.
1. Use the up/down buttons () in <Record> window to
move to <Event Record Duration>, and press [ENTER]
button. CH
1
Pre Event 
OFF 
POST Event 
1 min 
2 OFF  1 min 
2. Use direction buttons (◄ ►) to move to a desired 3

4
OFF
OFF


1 min
1 min


• Pre Event : The recording of an event will start at a
pre-determined time prior to the actual occurrence of the event.
If it is set to 5 seconds, the recording begins from 5
seconds before the event. OK Cancel
• POST Event : The recording will continue for a

pre-determined time after the actual end of an event.
If it is set to 5 seconds, the recording ends in 5 seconds after an event.
3. When the event recording duration setup is done, press <OK>.
REC Quality / Resolution

You can set resolution, fps and quality of recordings by channel, and by recording type of standard / event.
Setting Standard Recording Properties

You can set each channel’s resolution, quality and fps for normal recordings.
1. Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press Standard Event
[ENTER] button. Remaining count : 4CIF(L) : 2 2CIF(M) : 4 CIF(S) : 8
CH Resolution  Record Rate  Record Quality 

  
2. Select <Standard>. 1
2
CIF(S)
CIF(S) 
7fps
7fps 
Level4
Level4 
3 CIF(S)  7fps  Level4 
3. When the recording setup is done, press <OK>. 4 CIF(S)  7fps  Level4 
OK Cancel
English _49
using the DVR
Setting Event Recording Properties
You can set each channel’s resolution, quality and fps for event recordings.
1. Use the up/down buttons () in <Record> window to REC Quality & Resolution
move to <REC Quality & Resolution>, and press Standard Event
[ENTER] button. Remaining count : 4CIF(L) : 2 2CIF(M) : 4 CIF(S) : 8
CH Resolution  Record Rate  Record Quality 
2. Select <Event>. 1
2
4CIF(L)
4CIF(L)


7fps
7fps


Level4
Level4


Event recording setup window appears. 3 4CIF(L)  7fps  Level4 
4 4CIF(L)  7fps  Level4 

item, and select it.
• Resolution : Sets the resolution of the recorded screen.
• Record Rate : Image Per Second, means the frames OK Cancel
recorded per a second.

• Record Quality : Sets the recording quality.
M  The estimated total remaining count means the total number of remaining recordings for both standard and event
recordings.
 You cannot increase the remaining count if the current remaining count has reached zero or there is no available
remaining count from any other page. If this is the case, reduce the remaining count for the current page, or do so
for the same channel on any other page.
4. When the Event recording setup is done, press <OK>.
Record Option
You can set the recording to stop or overwrite when the HDD is full.
1. Use the up/down buttons () in <Record> window to Record Option
move to <Record Option>, and press [ENTER] button.
 Disk End Mode Overwrite
2. Use direction buttons (◄ ►) to move to a desired Disk End Beep
item, and set the value. Auto Delete

 Auto Delete 180 day
• Disk End Mode : If selected <Overwrite>, recording will The recording information will be deleted.
Do you want to proceed?

continue despite the HDD full while overwriting the oldest. OK Cancel
If selected <Stop>, the recording will stop when the HDD is

full.
• Disk End Beep : If selected <Stop>, the button is activated. OK Cancel
If you check it, the beep will sound on the disk full and the
recording stops.
• Auto Delete : If you check it, Record Period setup is activated.
If you specify the auto deletion period, the recording data before the period will be deleted automatically.
 This option will be enabled only if Disk End Mode is set to “Overwrite”.
3. When the recording option setup is done, press <OK>.
50_ using the DVR

SETTING THE EVENT
You can set recording options for sensor, motion, and video loss event.
Sensor Detection
You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration.
 USING THE DVR

Logout Return
2. Use the left/right button (◄ ►) to select <Event>.

Event setting menu is selected.
Event
Sensor Detection
Motion Detection
Video Loss Detection
Alarm Schedule
3. Use the up/down buttons () to move to <Sensor

Sensor Detection
Detection>, and press [ENTER] button.
Sensor Operation  Cam  Alarm  Duration 
A window of sensor detection setup appears. Sensor
1 OFF  1 None 10 sec 

4
OFF
OFF


3
4
None
None
10 sec
10 sec



• Sensor Operation : Sets the operation mode of sensors.
- <OFF> : Sensor does not operate.
- <N.O (Normal Open)> : Sensor is opened.
OK Cancel
If the sensor is closed, it generates alarm.
- <N.C (Normal Close)> : Sensor is closed.
If the sensor is open by interruption, it generates alarm.
• Cam : Select a channel to be connected to the sensor.
Sensor Detection
If selected camera, “Camera Setup” window appears.
Select a channel and setup the preset. Sensor
1
Sensor Operation 
OFF 
Cam 
1
Alarm 
None
Duration 
10 sec 
Camera Setup
4 OFF CH  4 None CH  10 sec 
1 3
2 4
OK Cancel
OK Cancel
• Alarm : Sets the alarm output method.

Sensor Detection
 For further information on alarm output, refer to “HDD Alarm >
Sensor Sensor Operation  Cam  Alarm  Duration 
Alarm”. (Page 45) 1 OFF  1 None 10 sec 
• Duration : Sets the duration of alarm signal and alarm 3

4
Alarm
OFF Setup
OFF


3
4
None
None
10 sec
10 sec


sound. 1 BEEP All
5. When the sensor detection setup is done, press <OK>. OK Cancel
OK Cancel
English _51
using the DVR
Motion Detection
You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.
1. Use the up/down buttons () in <Event> window to
Motion Detection
move to <Motion Detection>, and press [ENTER] button.
CH Mode  Sensitivity  Alarm  Alarm Duration 
A window of motion detection area setup appears. 1 OFF  Level10(High)  None 10 sec 
2 OFF  Level10(High)  None 10 sec 

4
OFF
OFF


Level10(High) 
Level10(High) 
None
None
10 sec
10 sec



• Mode : Sets whether to activate motion detection.
• Sensitivity : Sets the sensitivity level of the motion detection.
Motion Region
• Alarm : Sets the alarm output method.

 For further information on alarm output, refer to “HDD Alarm > OK Cancel
Alarm”. (Page 45)

• Alarm Duration : Sets the duration of alarm signal and alarm sound.
3. When the motion detection setup is done, press <OK>.
Setting the Motion Detection Area

Select <Motion Region>.
When “Motion Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Motion Region” window
In the “Motion Region” window, select desired region Motion Region
from < >. CH1
Individual Apply to All CH
• To set the area using <Individual> selection OK Cancel
In the “Motion Region” window, you can select cells

individually by using <Individual>.
When selected <Individual>, “Motion Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]
button on the remote control to display the “Motion Region” window again.
- Select : Selected cell is set to be a part of motion detection area. Select
- Unselect : Selected cell is removed from the motion detection area. Unselect
- Inverse : Unselected cells are set to be the motion detection area. Inverse
- Menu : After selecting individual motion areas, move to the “Motion Region” window.
Menu
 If selected <Apply to All CH>, selected motion area is applied to all channels.
When the motion detection setup is done, press <OK>.
52_ using the DVR

You can set the alarm to be generated on a camera disconnection, which causes a video loss.
1. Use the up/down buttons () in <Event> window to
move to <Video Loss Detection>, and press [ENTER]
Video Loss State  Alarm  Alarm Duration 
button. CH
1 OFF  None 10 sec 
A window of video loss detection area setup appears. 2

3
OFF
HelpOFF


None
None
10 sec
10 sec


4 OFF  None 10 sec 
2. Use direction buttons (◄ ►) to move to a desired If a video loss event occurs during the event
 USING THE DVR

recording, the POST recording settings of
the applicable channel will be reset.
item, and set the value. OK
• Video Loss State : Sets whether to activate video loss

Help
detection.
• Alarm : Sets the alarm output method. OK Cancel
 For further information on alarm output, refer to “HDD Alarm >

Alarm”. (Page 45)
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
• Help : Displays a help message that will appear if a video loss event occurs.
3. When the video loss detection setup is done, press <OK>.
Alarm Schedule
You can set the conditions and operating hours for scheduled alarms.
1. Use the up/down buttons () in <Event> window to Alarm Schedule
move to <Alarm Schedule>, and press [ENTER] button.
Alarm1
2. A window of <Alarm Schedule> settings appears. All

Sun
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mon
3. Alarm : Sets the alarm output method. Tue
Wed
 For further information on alarm output, refer to “HDD Alarm > Thu
Fri
Alarm”. (Page 45) Sat

Hol
OFF ON Event Sync Apply to All Alarm

• <ON> : Marked in orange, and always generates alarm on
scheduled time. OK Cancel
• <OFF> : Marked in white, no alarm is generated even if an

event occurs.
• Event Sync : Marked in Blue, generates alarm only when an
event occurs.
• Apply to All Alarm : Applies the configured schedule to all Alarm Schedule
alarms. Alarm1
All 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
M  When the alarm is generated on the scheduled time, you can

Sun
Mon Apply to All Alarm
Tue
stop the alarm by canceling the schedule. Wed
Apply the alarm scheduling to all?
Thu
Fri
4. When the Alarm Schedule setup is done, press <OK>. Sat

Hol
OK Cancel
OFF ON Event Sync Apply to All Alarm
OK Cancel
English _53
using the DVR
BACKUP
You can check the backup device and set the backup schedule by channel or by time.
The product only supports external HDD of USB memory and USB type. (Page 93)
Setting the Backup

You can backup the desired data to a connected device.

Logout Return
2. Use the left/right button (◄ ►) to select <Backup>.

Backup menu is selected.
Backup
Backup
3. Press the [ENTER] button. Backup

A backup window appears.
 Start  End
You can directly access it from the “Live screen menu”. 2011-01-01 00:01:06 2011-01-01 08:25:45
 Overlap List0
(Page 24) ALL 1 2 3 4

item, and set the value.  Device
 Folder
USB-Storage
\20110101\
 Type
 Filename
DVR
0001 Change
• Backup Range : Sets the <Start> and <End> time for the Check capacity Backup
Used
backup. Free
• Channel : Sets the channel to backup. OK Cancel
You can select multiple channels.

• Device : Select a backup device from the recognized devices.
• Type : Sets the backup data format.
- DVR : Saved data can be played back only by the DVR.
- SEC : Saves data in the Samsung’s proprietary format with built-in viewer, which supports immediate
playback on a PC.
• Filename : You can set the back file name.
• Check capacity : Shows the size of the selected backup data, used and available capacity of the selected
backup device.
 Checking will stop if the backup size is over 200%.
• Overlap : Shows a list of overlapping data on a same time according to the number of data.
It appears when one channel has multiple data on a certain time point due to changing of time or time zone
settings, etc.
 Refer to time and time zone of “Setting the Date/Time/Language”. (Page 32)
54_ using the DVR

5. When the backup setup is done, press <OK>.
 If no available device is recognized for backup, <OK> button is not activated.
J  The application may slow down during the backup.

 You can switch to the menu screen during the backup in operation, but playback of data is not available.
 If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the
HDD is properly connected.
M  Pressing the <Return> during the backup will return to the previous menu, while the backup progresses.
 USING THE DVR

NETWORK CONFIGURATION
It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can configure the network environment which enables such functions.
Connection Mode
You can set the network connection route and protocol.
Setting the Connection

Sets the protocol and environment of the network.
Logout Return
2. Use the left/right button (◄ ►) to select <Network>.

Network menu is selected.
3. Use the up/down buttons () to move to <Connection Network
Mode>, and press [ENTER] button. Connection Mode

DDNS
Live Transfer
Mailing Service
4. Select <Connection>.
Connection Mode
A window of connection mode setup appears. Connection Protocol
5. Use direction buttons (◄ ►) to move to a desired  Connection Mode Static IP

 Bandwidth
item, and set the value. 2Mbps
• Connection Mode : Sets the network connection mode.

 IP 192.168. 1.200
 Gateway 192.168. 1. 1
• Bandwidth : Sets the maximum data flow to be transferred.

 Subnet Mask 255.255.255. 0
 DNS Manual 168.126. 63. 1
(Upload speed)
Options will vary depending on the selected connection
mode. OK Cancel
- For <Static IP>, <Dynamic IP> : Select one from 50

kbps ~ 2Mbps, and Unlimited.
- For <ADSL>, select one from 50 kbps ~ 600 kbps.
English _55
using the DVR
• IP, Gateway, Subnet Mask, and DNS Connection Mode
- For <Static IP> : You can directly input IP address, Connection Protocol
Gateway, Subnet Mask and DNS.  Connection Mode ADSL

 Bandwidth 600kbps
- For <Dynamic IP> : IP address, Gateway, and Subnet
 IP
Mask are set automatically.  Gateway
192.168. 1.200
192.168. 1. 1
- For <ADSL> : IP address, Gateway, and Subnet Mask  Subnet Mask

 DNS
255.255.255. 0
Manual 168.126. 63. 1
are set automatically.

 User ID ID
 Password
• User ID, Password : In case you selected ADSL, provide the
************
OK Cancel
“User ID” and its “Password”.
M  DNS server for <Dynamic IP> and <ADSL> can be set by user only if you selected <Manual>.
6. When the connection setup is done, press <OK>.
Setting the Protocol

1. Use the up/down buttons () in <Network> window to Connection Mode
move to <Connection Mode>, and press [ENTER] Connection Protocol
button.
 Protocol Type TCP
 Port(TCP) 554 ~ 558
2. Select <Protocol>.  Port(UDP) 8000 ~ 8160
 Unicast/Multicast Unicast
3. Use direction buttons (◄ ►) to move to a desired  Multicast IP 224.126. 63. 1

 TTL 5
item, and set the value.  Webviewer Port 80
• Protocol Type : Select the protocol type between TCP and

UDP. OK Cancel
 If selected UDP, selections of Port (TCP), Port (UDP), and Unicast/

Multicast are activated.
 If setting the connection mode to ADSL, you cannot select UDP for the protocol type.
• Port(TCP) : Initially, <554~558> is set. It increases / decreases by 5.
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet
environments.
• Port(UDP) : Initially, <8000~8160> is set. It increases / decreases by 160.
- UDP : It has less stability and faster speed when compared to TCP, and recommended for local area
network (LAN) environments.
• Unicast/Multicast : Select one between Unicast and Multicast.
If selected Multicast, Multicast IP and TTL are activated.
- Unicast : Transfers data (UDP, TCP) individually to each connecting client.
- Multicast : Multiple client can receive the data (only in UDP) without putting additional traffic load to the
network.
• Multicast IP : User can directly input.
• TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.
• Webviewer Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.
M  As UDP protocol may cause a packet loss on the network, it is recommended to use TCP protocols.
 If you select UDP protocols and set port forwarding in the IP router, ending up with an unstable network connection,
configure the DMZ settings in the IP router as necessary.
4. When the protocol setup is done, press <OK>.
56_ using the DVR

Connecting and Setting the Network
Networking may differ from the connection method, check your environment before setting the connection
mode.
When no router is used

• Static IP mode
- Internet connection : Static IP ADSL, leased line, and LAN environments allows connection between the
DVR and remote user.
 USING THE DVR

- DVR Network Settings : Set the <Connection Mode> in
Connection Mode
<Connection> menu of the connected DVR to <Static IP>. Connection Protocol
 Consult your network manager for IP, Gateway and Subnet Mask.  Connection Mode Static IP
 Bandwidth 2Mbps
 IP 192.168. 1.200
• Dynamic IP (DHCP) mode  Gateway 192.168. 1. 1
 Subnet Mask 255.255.255. 0
- Internet connection : Connect the DVR directly to a cable  DNS Manual 168.126. 63. 1
modem, DHCP ADSL modem or FTTH network.

- DVR Network Settings : Set the <Connection Mode> in OK Cancel
<Connection> menu of the connected DVR to <Dynamic

IP>.
• ADSL (PPPoE: ID and password certification)

- Internet connection : An ADSL modem is directly connected to the DVR, where the ADSL connection
requires user ID and password.
- DVR Network Settings : Set the <Connection Mode> in
Connection Mode
<Connection> menu of the connected DVR to <ADSL>. Connection Protocol
 ADSL <User ID> and <Password> should be the same to the  Connection Mode ADSL
 Bandwidth 600kbps
ADSL user information.
If you don’t know the ID and password, consult your ADSL service  IP
 Gateway
192.168. 1.200
192.168. 1. 1
provider.  Subnet Mask 255.255.255. 0

 DNS Manual 168.126. 63. 1
 User ID ID
 Password ************
OK Cancel
English _57
using the DVR
When a router is used
 To avoid IP address conflict with the DVR's static IP, check followings :
J
• Setting the DVR with a static IP
- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or
a router in a Local Area Network (LAN) environment.
• Setting the DVR Network

1. Set the <Connection Mode> in <Connection> menu of the connected DVR to <Static IP>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP, Gateway, and Subnet Mask : Consult your network manager.
 Check whether the set IP address is in the static IP range provided by the Broadband Router.
 If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should
J set the IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~
192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
• Setting the DHCP IP Address of the Broadband Router

1. To access the Broadband Router’s configurations, open a web browser on the local PC that is connected
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).
2. At this stage, make the local PC's windows network configurations to the below example :
Ex) IP : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press <OK> to access the router configurations.
- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
Set the start address (192.168.0.100) and end address (192.168.0.200).
M  Above steps may differ from the router devices depending on the manufacturer.
• Setting Router’s Port Forwarding

1. Set the protocol to <TCP>. Connection Mode
Protocol
2. External Port Range : Enter the TCP Port set in the Connection
<Port(TCP)> in <Protocol> menu of the connected DVR.  Protocol Type TCP

 Port(TCP) 554 ~ 558
If more than one DVRs are connected to the router, the  Port(UDP) 8000 ~ 8160
TCP port can be different.  Unicast/Multicast

 Multicast IP
Unicast
224.126. 63. 1
 TTL 5
3. Internal PC IP Address : Enter the IP address set to the  Webviewer Port 80
<IP> in <Connection> menu of the connected DVR.

4. Internal Port Range : Set the same to the “External Port OK Cancel
Range”.
M  Above steps may differ from the router devices depending on the manufacturer.
Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s
network.
58_ using the DVR

DDNS
You can set the DDNS site for a remote user’s network connection.
1. Use the up/down buttons () in <Network> window to DDNS
move to <DDNS>, and press [ENTER] button.
 DDNS Site iPOLiS
2. Use virtual keyboard to enter user inputs.  Host Name www.samsungip...

 User Name
 Refer to “Using Virtual Keyboard”. (Page 34)  User Password

 DDNS Host Address http://www.samsungipolis.com/
 USING THE DVR

 If selected <OFF> or <iPOLiS>, input fields are deactivated.
 If you select <iPOLiS>, the “DDNS host address” item will be
displayed.
OK Cancel
3. When the DDNS setup is done, press <OK>.
DDNS Setting
DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP
system.
• Setting DDNS in the DVR

Set <Protocol Type> in the <Protocol> menu of the connected DVR to the following :
Ex) Protocol Type : TCP
Port (TCP) : 0554, 0555, 0556, 0557, 0558
DDNS Site : iPOLiS
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
1. In the <Network> setting window, press the up/down
Live Transfer
() button to move to <Live Transfer> and press the
[ENTER] button.  Resolution CIF(S)
 Quality Low
The Live Transfer window appears.
2. Use the direction buttons (◄ ►) to move to a desired
item and set the value.
3. When the live transfer is done, press <OK>.
 For the resolution of the live transfer, refer to “Resolution”.
OK Cancel
(Page 49)
English _59
using the DVR
Mailing Service
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.
 If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set
M to <OFF>, only the text notification will be sent to the applicable email address.
SMTP Setting
Sets the SMTP mail server.
Mailing Service
() button to move to <Mailing Service> and press the SMTP Event Group Recipient
[ENTER] button.  ServerType SMTP mail Server
 Server
2. Select <SMTP>.  Port 25
You will see the SMTP setting window. Use Authentication

 User
3. Use direction buttons (◄ ►) to move to a desired item  Password
 Secure Transfer Never

and set the value.  Sender ex. user@example.net
TEST
• ServerType : Displays the connected server type. OK Cancel
• Server : Enter a server to connect to.

• Port : Sets the communication port.
• Use Authentication : Check this if the SMTP server uses user authentication.
The account input box will be activated.
• User : Enter a user to use authentication when connecting to the SMTP server.
• Password : Enter the password of the SMTP server user.
• Secure Transfer : Select one from <Never> and <TLS(if Available)>.
• Sender : Use the virtual keyboard to enter the sender’s e-mail address.
• TEST : Conducts the test on the server settings.
4. When the SMTP setting is done, press <OK>.
Event Setting
You can set the interval and type of the event that will be sent to the user.
Mailing Service
[ENTER] button.  Event Interval 10 min
2. Select <Event>.  Use Event Transfer

Sensor Motion
3. Use direction buttons (◄ ►) to move to a desired item Change P/W HDD Info Video Loss
Power On/Off Manual Record
and set the value.
• Event Interval : Set the event interval.
 If a series of events occurs, the e-mail will be sent at the specified OK Cancel
interval, not on each event.

• Use Event Transfer : Select an event type to send if an event occurs.
If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.
4. When the event setting is done, press <OK>.
60_ using the DVR

Group Setting
You can set the group to whom the e-mail is sent, and specify the permission for each group.
You can add recipients for each group in the <Recipient> menu item.
The recipient is set separately from the DVR user group.
Mailing Service
[ENTER] button.  Group Add Delete Rename
 USING THE DVR

 Recipient Permission
2. Select <Group>. Sensor Motion
3. Use direction buttons (◄ ►) to move to a desired item Change P/W

Power On/Off
HDD Info
Manual Record
Video Loss
and set the value.

• Add : Select <Add> and use the virtual keyboard to add a
group. OK Cancel

• Delete : Deletes the selected group.
• Rename : You can reset the recipient permission of an existing group.
• Recipient Permission : Set the permission of the recipient group.
4. When the group setting is done, press <OK>.
Recipient Setting
You can add/remove a recipient(s) to/from the specified group and edit the group if necessary.
1. In the <Network> setting window, press the up/down Mailing Service
[ENTER] button.  Group All Group Add
Group Name e-Mail Address Del

2. Select <Recipient>.
3. Use direction buttons (◄ ►) to move to a desired item
and set the value.
Previous/ Next Page
OK Cancel
• Add : You can select a recipient name, e-mail address or

Mailing Service
group. SMTP Event Group Recipient
You should have created a group in the <Group> menu  Group ABC Add
item before you can add a user to the group. Group

Add recipient
Name e-Mail Address Del
 For inputting the recipient name and email address, refer to

 Name
 Email
“Using Virtual Keyboard”. (Page 34)  Select Group ABC
OK Cancel
4. When the recipient setting is done, press <OK>.

Previous/Next Page
OK Cancel
English _61
search & play
SEARCH
You can perform the search for recorded data by the time or by the search criteria such as an event.
You can access the <Search> menu directly in Live mode.
1. In Live mode, right-click any area of the screen. Scene Mode 
2011-01-01 01:10:25 
The Live menu appears. Spot Out
Audio Off
Freeze
2. Select <Search>. Stop Alarm

Record
Or, press the [SEARCH] button on the remote control. Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. The Search menu appears.

2011-01-01 01:10:25
4. The search can be restricted by the Auto Delete function.

Refer to “Setting the Recording > Record Option”.
Return
(Page 50) Time Search
Event Search
M  Overlapped data : It only appears if there exists overlapped Backup Search

Motion Search
data on a certain time, produced due to the change of DVR’s
time setup. The latest data comes first, from <List0>.
It does not appear in <Backup Search>.
Time Search
You can search for recorded data of a desired time.
As the time to display may be different depending on the time zone and the DST standard time, the time of
data recorded in the same time can be displayed differently depending on time zone and DST settings.
1. Select <Time Search> in the <Search> menu.
Time Search
2. Select a date to search. 2011-01-01 Go to First Go to Last
Overlapped Data List1 Zoom In Zoom Out
 Refer to “Using the Calendar”. (Page 33) 00:01

All Data
CAM 01
3. The record data on the specific date will be listed. CAM 02

CAM 03
The display bar is different according to the data type. 2011/01/01 00:01:17 CAM 04
So check the data type for the color in the left pane. Standard
Motion
Schedule
Sensor
V.Loss Etc
4. Use direction buttons (◄ ►) to set the search criteria

and press the [ENTER] button. Play Return
• Go to First : Moves to the earliest date.

• Go to Last : Moves to the most recent date.
• Time : Enter a time to perform the search or use the up/down button <>> to select one.
62_ search & play

• Zoom In : The map enlarges in detail. Time Search
It will switch in the sequence of 24 hours - 16 hours - 8 hour 2011-01-01 Go to First Go to Last
- 4 hours. Overlapped Data List1 Zoom In Zoom Out
• Zoom Out : The map will switch in the reverse order of the
00:01
All Data
CAM 01
detailed mode above. CAM 02
It will switch in the sequence of 4 hours - 8 hour - 16 hours 2011/01/01 00:01:17

CAM 03
CAM 04
- 24 hours. Standard Schedule

Motion Sensor
V.Loss Etc
M  Double-click a desired time to zoom it in/out. Play Return
 SEARCH & PLAY

• Preview : Click <Channel> and select (click, drag) a time in
<Duration> to display a still image for the portion.
- If the selected channel does not contain any recorded data, it will be marked black.
5. Select a data item and click <Play>.
The screen switches to the data playback mode.
Event Search
You can search for events by the channel and play them.
1. Select <Event Search> in the <Search> menu.
Event Search
2. Use direction buttons (◄ ►) to set the search criteria CAM 01
and press the [ENTER] button. 2011-01-01
Overlapped Data List1 Go to First Go to Last
 All record events on a specific date will be found. (Normal/ No.

3
Date/Time Preview
02:47:54 ~ 02:48:59
Event
Motion
Schedule recording included) 2 00:39:06 ~ 00:40:30 Motion
1 00:01:22 ~ 00:02:28 Motion
• Date/Time Preview : If you select a data item in the list, the 2011/01/01 00:01:22
still image of the selected data will be displayed in the left

Previous/Next Page
preview pane.
Play Return
• Event : Displays the type of the event that occurred.

The screen switches to the event data playback mode.
Backup Search
Searches for backup data in the connected backup device.
Only data in the format of DVR is included in the search.
Refer to <Type> in “Backup > Setting the Backup”. (Page 54)
1. Select <Backup Search> in the <Search> menu.
Backup Search
2. Use direction buttons (◄ ►) to set the search criteria USB:USB2FlashStorage
No. Folder Name File Name

and press the [ENTER] button. 1 20110101 16190000
• Record Period : Displays the record period.

• Channel : Displays the recorded channel.
• Play Start Time : Select a time that you start playing.  File Name 16190000
Previous/Next Page
 Channel 1
 Record Period 2011-01-01 01:01:01 - 2011-01-01 01:01:10
3. Select a data item and click <Play>.  Play Start Time 2011-01-01 01:01:01
The screen switches to the backup data playback mode. Play Return
English _63
search & play
Motion Search
If a motion is detected in each channel, you can set a desired area to perform the search.
You can use the mouse to select the related items.
1. Select <Motion Search> in the <Search> menu.
Motion Search
2. Use direction buttons (◄ ►) to set the search criteria Channel CAM 01 Motion Region All Area Setup
and press the [ENTER] button. Date/Time 2011-01-01 03:41:18 2011-01-01 05:11:44 Search
Overlapped Data List1 Go to First Go to Last
 If you set the motion area to <Manual Area>, the <Setup> No.
7
Start Time
01:01:30
button will be activated. 6 01:01:25
5 01:01:20
4 01:01:15
• Motion Region : Select an area to perform the search. 2011/01/01 01:01:30 3

2
01:01:10
01:01:05
1 01:01:01
- All Area : Searches for all areas of the selected channel. Previous/Next Page
- Current Area : Searches for the motion area for each Play Return
channel specified in “Motion Detection >

Setting the Motion Detection Area”. (Page 52)
- Manual Area : You can set the motion area manually.
• Setup : The Setup button will be activated only if you have
set the motion area to Manual. Press this button to display
the area setting window.
• Date/Time : The Date/Time will be automatically set by the
hour, and the end time will be automatically set to one hour
Motion Region
later than the start time if it is set. CH1
• Preview : Select a data item in the list to display the still Individual Apply to All CH
image of the item. OK Cancel

The screen switches to the motion data playback mode.
64_ search & play

PLAYBACK
Play
You can play data stored in the HDD and backup a desired portion of the data.
1. In Live mode, click <Play> in the right-click menu or Scene Mode 
2011-01-01 01:10:25
< > in the launcher menu, or press the Play button on Spot Out
Audio Off

the remote control.
 SEARCH & PLAY

Freeze
Stop Alarm
Record
2. Use the up/down button () to select a menu. Play
 For data search, refer to <Search>. (Page 62)

Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
3. Select a data item and click <Play> in the Search menu.

2011-01-01 01:10:25
The selected data is played and the play launcher appears
on the screen.
 If there is an existing data, <Play> will start immediately without
performing the search.
• Playback Information : Displays the date and time of the
current data in the top corner.
REC
• Backup : Click < > to set the current time to the start Backup Range
time of backup; you can specify a backup area using the
 Start  End
mouse (yellow triangle). 2011-01-01 00:01:06 2011-01-01 01:10:25
 Device USB Storage  Type DVR
Click < > again to set the current time to the end time of  Folder \20110101\  Filename 0001 Change
the backup and the “Backup Range” window appears. Check capacity Backup
Used
- Type : Supports formats of DVR and SEC. Fre
Refer to a list of formats in “Setting the Backup”.

(Page 54)
- Device : Select a backup device.
Backup Cancel
- Check Capacity : Enables you to check the capacity of the
selected storage device.
4. If you want to return to the Live screen in Play mode, click < > in the launcher menu or press the
[] button on the remote control.
English _65
search & play
Using the Playback Button
REC
Play Timeline Indicates the current playback point, and can be used to move.
b Skip Backward Moves backward by unit time.
Backward Fast
c Play
Used for quick backward search while in Play.
Backward Slow
Play
Used for backward frame-by-frame search while in PAUSE.
Step Backward Moves backward by one frame at a time.
Pause Stops playing the current video temporarily.
Stop Stops playback and moves to the live screen.
Step Forward Moves forward by one frame at a time.
Ensured to play forward up to 4 channels simultaneously at a low speed.

Forward Slow
Play
 In a split mode, the real time playback may not be supported, depending on the record
quality, resolution and number of channels. And some frame rates may be supported.
Forward Fast
Play
Used for quick forward playback.

Skip Forward Moves forward by unit time.
Return Return to the previous.
Sets Audio ON/OFF.

m Audio  If using both web view and DVR set simultaneously, the audio signal will be output from the
DVR set.
n REC Records all channels in Live mode.
Begins backup of the selected section of the video being played, with the specified starting/
Partial Backup
ending point.
Mode Switch Click a desired playback mode or press [MODE] to switch the screen mode in sequence.
66_ search & play

web viewer
INTRODUCING WEB VIEWER
What is Web Viewer?

Web Viewer allows remote access to your DVRs. You have
access to live video, archived video etc.
 WEB VIEWER
PRODUCT FEATURES
• Remote access from a standard browser
• Supports 1, 4 camera viewing formats (maximum of 4
cameras in the list).
• Gets JPEG, BMP format images to print and save to “Print
or Save JPEG, BMP format images”.
• Record video in AVI format-compatible with popular media
players. (needed the H.264 codec)
SYSTEM REQUIREMENTS
The following lists the minimum suggested hardware and operating system requirements needed to run the
Web Viewer.
Windows XP Professional
Windows 2000
OS
Windows Vista Home Basic / Premium
Windows 7
Web Browser Internet Explorer 6.0.2900.2180 or higher
CPU Intel Pentium 4, 2 GHz
Memory 512 MB
Monitor High Color 16-bit 1024 x 768
50 MB(Installation space required)

HDD * Additional HDD space required for recording.
Recorded file size will vary depending on recording quality settings.
English _67
web viewer
CONNECTING WEB VIEWER
1. Open your web browser and type the IP address or URL
of DVR into the URL address box.
M The basic URL of the DVR is as following in case of MAC

address :
 http://www.samsungipolis.com/User ID
 You can also use registered URL which setups up in the Setup menu of your DVR.
2. Set the Admin ID and password same to those of the DVR

Admin.
For general users, enter the DVR user ID and password.
 The default password can be exposed to a hacking thread so

J it is recommended to change the password after installing the
product.

M 
It allows up to 4 simultaneous access including the Admin and general users.
It does not allow multiple login of the Admin user.
 Initial password of the Admin user is set to “4321”.
 Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.
 Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the
Web Viewer. (Page 37)
 All settings are applied by the DVR’s settings.
3. Click <Install ActiveX Control…>.

Downloading Active-X control may take several minutes
according to the security settings on your PC.
4. Click <Install>.
68_ web viewer

5. You may have “Windows Security Alert” that attempts to
block this with the Windows Firewall. In that case, click
<Unblock> to start Web Viewer.
6. Installation is complete.
Now you can see the main screen of Live Viewer.
 WEB VIEWER
USING LIVE VIEWER
The Live Viewer screen consists of following :

This displays the IP address and the model name of the connected DVR.
b These menus consist of <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.
c These buttons are used for the screen split and full screen mode.
Shows the IP address and model name of the connected DVR.
Select the format of OSD information that will be displayed on Live Viewer.
These buttons are used for sequence and changing the screen channel.
These buttons are used for capture, print, and save the image.
Shows the channel of the connected DVR.
This displays the screen for connected camera with DVR.
M  The resolution is set to 1024X768 pixels.

 The initial split-screen mode is set according to the number of channels connected to DVR. You can change the
split-screen mode by clicking buttons for split-screen modes.
English _69
web viewer
OSD INFORMATION DISPLAY
The channel number, video size, and IP address of the connected
DVR are displayed.
b The current date and time will be displayed according to the
selected time information display setting <DVR Time> or
<PC Time>.
c Alarm icon appears when alarm is issued.
It disappears when pressed the [ALARM] button of the DVR.
Motion icon appears when motion is detected.
It disappears when pressed the [ALARM] button of the DVR.
SPLIT-SCREEN
You can change the split mode by clicking each number icon.
SINGLE MODE QUAD MODE
• Click < > button.

The screen displays the selected camera connected to the DVR in
“SINGLE MODE”.

“QUAD MODE”.

“FULL SCREEN MODE”.
Double clicking on the screen or pressing any button of the keyboard
returns to the previous mode.
70_ web viewer

CONNECTED DVR
This displays the IP address and the status of the connecting DVR.
M  Connection failure message

No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
 The number of simultaneous connections are limited to 4.
 WEB VIEWER
Setting the display of the OSD time information
Select <DVR Time> or <PC Time> for the OSD time information display
setting.
• DVR Time : Based on the time of the connected DVR
• PC Time : Based on the time of the PC currently running the Web Viewer.
CHANGING THE LIVE SCREEN MODE

• SEQUENCE : When this button is clicked, screens are switched at a
preset interval.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
In QUAD MODE, the screen refreshes at the preset interval.
 Preset interval (10 seconds)
• PREVIOUS : When this button is clicked, the previous screen appears.
In QUAD MODE, the screen is refreshed.
• NEXT : When this button is clicked, the next screen appears.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
In QUAD MODE, the screen is refreshed.
English _71
web viewer
SAVING THE LIVE SCREEN ON THE PC
• CAPTURE : Saves the current screen into a BMP or JPEG
file.
M  The default saving path is “C:\Program Files\Samsung\Dvr

Web Viewer\SnapShot\Live”. To change the saving path, click
<SAVE PATH ( )> button and then select the path you
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\
SnapShot\” by default.
 The file is automatically named as following : “IP address_Port number_YYYYMMDD_HHMMSS_camera number_
index”
Ex) 192.168.1.200_554_20110414_093118_01_00
• PRINT : Prints out the selected screen out of the currently

displayed live screens. It also prints the IP address, time,
camera number and the current event status together.
• RECORD : Saves the current image on the screen and

saves it as a avi video file.
M  To record it, it is required at least 1GB of available space.

 The default saving path is “C:\Program Files\Samsung\Dvr
Web Viewer\VideoClip\Live”. To change the saving path, click
<SAVE PATH ( )> button and then select the path you
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\Local-Low\Samsung\DVR Web Viewer\VideoClip\”.
index”
Ex) 192.168.1.200_554_20110406_070455_01_00
 For AVI Save, you need the H.264 codec for playing saved files.
 HDD Minimum Free Size : During the recording, if there is no more capacity available in the HDD than set free space
will prompt with a popup message : “Cannot record due to insufficient disc space in the HDD”.
CHANGING THE LIVE SCREEN CHANNEL

• Blue numbers : The channel connected to the current live
screen
• Gray numbers : The channel not connected to the current
live screen
 If you select 4-split mode, the channel button for each of cameras
1 ~ 4 will turn blue.
72_ web viewer

USING SEARCH VIEWER
 WEB VIEWER
The Search Viewer screen consists of following :
This displays the IP address and the model name of the connected DVR.
b There are 4 tabs available: <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.
c Switch to a split mode.
Shows the IP address and model name of the connected DVR.
Select to turn the sound on/off.
These buttons are used for capture, print, and save the image.
This displays a calendar at which you can search the recorded video.
This displays a timeline at which you can search the recorded video by the time.
These buttons are used for controlling playback.
This displays the screen for playback of recorded video.
M  <SEQUENCE>, <PREVIOUS>, <NEXT> buttons are not available in SEARCH menu.

 During the DVR backup, you may have a trouble accessing CMS & Web Search.
English _73
web viewer
SPLIT-SCREEN
You can change the split mode by clicking each number icon.
SINGLE MODE QUAD MODE

“SINGLE MODE”.

“QUAD MODE”.
CONNECTED DVR
The IP of the connected DVR will be displayed.
M  Connection failure message

No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.
 The number of simultaneous connection is limited to 2.
74_ web viewer

SAVING THE LIVE SCREEN ON THE PC
• CAPTURE : Saves the current screen into a BMP or JPEG
file.
M  The default saving path is “C:\Program Files\Samsung\Dvr

Web Viewer\SnapShot\Search”. To change the saving path,
click <SAVE PATH ( )> button and then select the path
you want. For Windows Vista or 7, the saving path is “C:\
users\(user ID)\AppData\LocalLow\Samsung\DVR Web
 WEB VIEWER
Viewer\SnapShot\”.
index”
Ex) 192.168.1.200_554_20110414_093118_01_00
• PRINT : Print out the current screen. It also prints IP

address, time, camera number and current event state.
• RECORD : While in playback, press this button saves the

video data of the selected channel as an AVI file. (It is saved
in the designated folder on your PC.)
To stop recording, click this button again.
M  To record it, it is required at least 1GB of available space.

 The default saving path is “C:\Program Files\Samsung\Dvr
Web Viewer\VideoClip\Search”. To change the saving path,
click <SAVE PATH ( )> button and then select the path you want. For Windows Vista or 7, the saving path is
“C:\users\(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\VideoClip\”.
index”
Ex) 192.168.1.200_554_20110406_070455_01_00
 For AVI save, you need the H.264 codec for playing saved files.
English _75
web viewer
SEARCHING THE RECORDED VIDEO IN THE CALENDAR
If the video data has been recorded on a date, the date is
distinguished in green. If you click the date, the recorded video
information is displayed in the time line. When you click
<Today>, it will be synchronized with the system time (date) of
the current PC.
SEARCHING THE RECORDED VIDEO IN THE TIMELINE

It displays the recorded video data status on the DVR after a date is
selected. The normal mode displays the time ranging from 0 to 24 Hours
while the extension mode displays the time every 2 hours.
[Normal Mode]
• If you click < > button, it changes to the extension mode.
• Each time line represents 1 hour.
[Extension Mode]
• If you click < > button, it changes to the normal mode.
• Each time line represents 5 minutes.
M  The channels are ranging from CH01 to CH04.
76_ web viewer

CONTROLLING PLAYBACK
 WEB VIEWER
Fast Backward : Reverse-plays faster(2x~64x).
b Reverse Play : Performs Reverse Play.
c Play : Performs playback.
Fast Forward : Plays faster(2x~64x).
Go to First : Moves the beginning time of recorded video in the time line.
Step Backward : Performs one step reverseplay by one frame.
Pause : Stops the playback temporarily.
Step Forward : Performs one step forward by one frame.
Go to Last : Moves the last time of recorded video in the time line.
M  Only the admin account can play the audio signal during the playback.
If using both web view and DVR set simultaneously, the audio signal will be
output from the DVR set.
VIEWER SETUP
You can configure the DVR settings remotely on the network.
To configure the DVR settings, click <Setup>.
System
You can configure the various settings of the DVR system.
Date/Time/Language
For more information, refer to <Date/Time/Language> in the <System Setup> menu. (Page 32)
1. Select <Date/Time/Language> in the System menu.
2. Configure the DVR settings according to your system
environment.
• Date/Time
Set the date and time.
English _77
web viewer
• Time Synchronization Setup
Set the time synchronization.
• Display
Date Format : Set the date type.
Time : Select a time format to display on the screen.
• DST (Daylight Saving Time)
DST is displayed an hour ahead of the standard time of the
time zone.
• Language
Select a preferred language for the DVR.
Holiday
You can set specific dates to Holidays according to your
preferences.
For more information, refer to <Setting Holiday> in the
<System Setup> menu. (Page 33)
For more information, refer to <Permission Management> in the <System Setup> menu. (Page 34)
• Admin
You can change the admin ID or the password.
78_ web viewer

• Group
Users are classified into groups and the permission can be
set according to the group.
 First of all, add a group.
 WEB VIEWER
• User
You can add, change or remove a user or users.
• Setup
You can set the user permission.
System Management
For more information, refer to <System Management> in the <System Setup> menu. (Page 38)
• System Information
You can see information of the current system.
Check the software version, broadcast format and
MAC address.
English _79
web viewer
Device
You can check a list of devices that are connected to the DVR and configure the necessary settings.
Click <Device> in the menu screen.
For more information, refer to “Setting the Device”. (Page 42)
Camera
• Camera
You can configure the settings of the camera that is
connected to the DVR.
Storage Device
You can check and change the settings of the storage device.
• Device
You will see a list of storage devices that are connected to the
DVR.
You can check the type, used/total, usage and status of the
device.
• HDD Alarm
You can set the alarm output channel and the alarm duration
for an error.
80_ web viewer

Remote Device
Specify the use of remote control and the remote control ID so
that you can synchronize with the DVR.
 WEB VIEWER
Monitor
• Monitor
You can configure the monitoring screen settings and set the
output system.
• Spot Out
With the monitor connected via the SPOT port, if there occurs
an event such as Sensor, Motion, or Alarm, you can select a
video output mode for external monitoring.
• Mode
You can switch between live mode and play mode.
English _81
web viewer
Record
For more information, refer to <Setting the Recording>. (Page 48)
Recording Schedule
If you set a recording schedule for a specific date and time,
the recording will start at that specific time.
- Apply to All CH : Click <Apply to All CH> to display the

confirmation window.

You can set the start and end times of recording that will be
activated if an event occurs.
82_ web viewer

• Standard/Event
You can set the resolution, frame rate and recording quality for
each channel.
 WEB VIEWER
Record Option
You can set the Disk End Mode.
Event
For more information, refer to <Setting the Event>. (Page 51)
Sensor Detection
You can set the sensor operation mode and the synchronized
camera as well as the alarm output type and the duration.
English _83
web viewer
Motion Detection
You can set the motion detection mode and the sensitivity
as well as the alarm output type and the duration.
• Motion Region
Set the target motion detection area

You can set the alarm output time if a video loss occurs.
Alarm Schedule
You can schedule the alarm output according to the day of
the week and the time.
The default setting is Event Sync, which activates the alarm
only if an event occurs.
84_ web viewer

Network
For more information, refer to <Network Configuration>. (Page 55)
Connection
A remote user can access the DVR via the network to check
the current mode and the IP address.
• Connection
You can set the network connection route.
 WEB VIEWER
• Protocol
You can configure the protocol related settings.
DDNS
You can check the DDNS settings.
Live Transfer
A remote user can set the images of the DVR.
• Live Transfer
A remote user can set the image resolution of the transferred
data.
English _85
web viewer
Mailing Service
You can specify the SMTP server that sends a mail if an event
occurs and set the recipient group and users.
• SMTP
You can set the server that sends mails and specify if you use
the authentication process.
• Event
You can set the event interval and specify which events the
server sends mails for.
• Group
You can add a group to receive the mail if an event occurs
and set the permission to receive the event mail for each
group.
• Recipient
You can add a user or users who will receive the mail.
86_ web viewer

ABOUT
Click <ABOUT>.
Displays the model name of connected DVR and the version
of Web Viewer.
 WEB VIEWER
MOBILE VIEWER
What is Mobile Viewer?

Mobile Viewer is management software that enables you to
connect to DVR (Digital Video Recorder) remotely and control
the video playback and PTZ operations (if confi gured) in real
time.
Key Features 1.X

• Remote access via Smart phone
• 1-split and 4-split modes supported in Live Viewer
(However, search is not available).
• Switch channels using the touch-sensitive LCD panel
• Up to 4 channels supported
• Audio (wifi : O, 3G : X)
Supported Smart phone

• iPhone OS v4.2.1
• Android 2.1/ 2.2/2.3 (Galaxy S/S2)
M  For more information, refer to the user manual.

(http://www.samsungcctv.com)
English _87
backup viewer
SEC BACKUP VIEWER
You can play a file that is backed up in the format of SEC.
Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer.
If you run the backup file viewer, the backup data file will be automatically played.
Recommended System Requirements

PCs with a lower specification than the recommended below may not fully support forward/backward and
high-speed playback.
• OS : Windows XP professional, Windows Vista, Windows 7
• CPU : Intel Core2-Duo 2.4GHz or higher
• RAM : DDR PC-3200 1G or more
• VGA : Geforce 6200 or higher
88_ backup viewer

Name Description
A toggle button. Each time you press this button, the audio output will toggle
/
between activated and deactivated.
Audio
You can adjust the volume level from 0 to 100.
Saves the current screen as an image file. Supported file formats include
BMP and JPEG.
b
 BACKUP VIEWER
Screen Printout
Prints out the current screen. You should have installed the appropriate
printer driver before you can print out the screen.
A toggle button. Each time you press this button, it will toggle between
activated and deactivated. The closed lock icon indicates activation of the file
c File Tamper
Detection / tamper detection, which will blink the screen three times and stop playing if
an unauthorized manipulation of a data file is detected.
 A message of “The file is forged” will display in the menu bar.
Deinterlace You can enable the De-interlace function.
Collapses the time range that is displayed on the range bar of the storage
time. You can collapse the range bar until the overall range is shortened to 24
hours.
Zoom In/Out
Enlarges the time range that is displayed on the range bar of the storage
time. You can enlarge the range bar until the overall range is extended to 1
minute.
Display of storage time range

Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
A toggle button; each time you press this button, the "Slow Playback" icon
changes its color to display it’s activated/deactivated. If it is activated, you
can use the play speed control to adjust the play speed up to x1/16 forward
and backward respectively, whereas if deactivated, you can adjust up to x16
forward and backward.
A toggle button; each time you press this button, the "Lock Speed" icon
changes its color to display it’s activated/deactivated.
Speed
If activated, the adjusted speed will be kept even if you release the mouse on
the speed bar. If deactivated, the adjusted speed will be applied only while
you use the mouse to hold the adjusted speed, and if you release the mouse,
the speed will restore to x1.
You can adjust the play speed up to x16 forward and backward respectively,
which varies according to the frame rate per second of the source.
Fast playback maximum is limited to x2 for footages recorded at 20 ~ 30 fps
(frames per second), x4 for 11 ~ 19 fps, x8 for 6 ~ 10 fps, and x16 for footages
recorded at slower than 6 fps.
Displays the next frame. This is available only if the playback is stopped.
A toggle button. Press it once to start playing the video and switch the button
Play mode to 'Pause', and press it again to switch the button mode to Play and
stop playing temporarily.
Displays the previous frame. This is available only if the playback is stopped.
English _89
appendix
PRODUCT SPECIFICATION (CAMERA)
Details
Item
SEB-1005R N SEB-1005R P SEB-1007R N SEB-1007R P
Electrical
Input Voltage DC 12V(by UTP)
Power Consumption 2.6W
Video
Imaging Device MT9V138
Total Pixels 680 x 512
Scanning System Interlace
Synchronization Internal
H: 15,734 Hz H : 15,625 Hz H: 15,734 Hz H : 15,625 Hz
Frequency
V: 59.94 Hz V : 50 Hz V: 59.94 Hz V : 50 Hz
Horizontal Resolution 520TVL
Min. Illumination OLux (IR-LED)
S/N Ratio (Y Signal) 46dB
Built-in UTP TX
UTP Maximum Transmission Length: 200m (UTP CAT 5e, all of 8 pins are used)
Balanced Differential Impedance: 100 ohm
Lens
Focus Length 3.6mm
Max.Aperture Ratio 2
H: 56˚
Angular Field of View
V: 42˚
Operational
Shutter Mode Auto (Rolling Shutter)
Gain Control Auto
White Balance Auto (3200°K~6500°K)
Digital Noise Reduction Auto
Day & Night Auto
Night-Visibility 15m (20EA)
90_ appendix
Details
Item
SEB-1005R N SEB-1005R P SEB-1007R N SEB-1007R P
Environmental
Operating Temperature/
0°C ~ +40°C (+32°F ~ +104°F) / 20% ~ 85% RH
Humidity
Mechanical
Dimension (W x H x D) W65.5 X H65.5 X D94.6 (2.58 X 2.58 X 3.72 inch) W59.1 X H59.1 X D72 (2.33 X 2.33 X 2.83 inch)
 APPENDIX
Weight 300g 115g
English _91
appendix
PRODUCT SPECIFICATION
Details
Item
SDE-3001 SDE-3003
Inputs 4 UTP Line(CH1~CH4)
Video
Resolution 704x480 NTSC, 704x576 PAL
Frame rate 30fps NTSC, 25fps PAL
Live Resolution 704x480 NTSC, 704x576 PAL
Multi Screen display 1, 4, PIP
Performance
Operating System Embedded Linux
Compression H.264
NTSC : Up to 30fps @ 704x480 / PAL : Up to 25fps @ 704x576
Record Rate NTSC : Up to 60fps @ 704x240 / PAL : Up to 50fps @ 704x288
NTSC : Up to 120fps @ 352x240 / PAL : Up to 100fps @ 352x288
Recording NTSC : Manual, Schedule, Event, Time Laps
Mode
PAL : Manual, Schedule, Event, Time Laps
Overwrite modes Continuous
Pre-Alarm Off / 5sec
Post-Alarm Up to 6 hour. (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min,1, 2, 3, 4, 5, 6 hour)
Search mode Date/time, Event, Back up, Motion
Search & Playback
Playback function Fast Forward/Backward, Slow Forward/Backward, Step Forward/Backward
Transmission speed 100 / 120fps
Up to (4)Mbps, Unlimited(4M)/2/1.5/1 Mbps/800/600/500/400/300/200/
Bandwidth
100/50 kbps
Bandwidth control Automatic
Network Stream H.264(CIF)
Maximum No. of remote
Search(2) / Live Unicast(4) / Live Multicast(20)
users
Protocol support TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP
Monitoring Smart viewer, Webviewer, Mobile Viewer
Smartphone SmartPhone Support
Internal HDD 500GB SATA HDD 1TB SATA HDD
External HDD –
Storage DVD Writer (Back-up) –
USB (Back-up) 2 USB Ports
File Forma (Back-up) BU(DVR Player), EXE(Include Player)
92_ appendix
Details
Item
SDE-3001 SDE-3003
Password Protection 1 Admin, 10 Group, 10 User per 1 Group
Security
Data Authentication Watermark
Interface
VGA Analog RGB 1024x768 resolution(BNC or VGA selected in booting.)
HDMI –
 APPENDIX
Monitors Main Composite BNC, 1 Vp-p, 75 ohm
Spot Composite –
Loop Outputs –
Inputs/Output 1 Line in(CH1) / 1 line out(RCA)
Audio Compression G.711
Sampling rate 8KHz
Terminal 4 inputs (NO/NC) / Terminal 1 relay outputs (NO/NC),
Inputs/Outputs
Alarm Rating : 24V DC 1A, 125VAC/0.5A
Remote notification Notification via e-mail
Ethernet 1 RJ45 10/100 Base-T
Serial interface –
USB USB 2.0, 2 ports (Front/Rear)
Connections
e-SATA –
Application Supoort Mouse (1EA), Remote Controller
Protocol support –
General
Input Voltage/Current 100 to 240 VAC ±10%; 50/60 Hz, Autoranging
Electrical
Power consumption ADP-4812 Adaptor (1EA), 48W
Operating Temperature/
Environmental 0°C ~ +40°C (+32°F ~ +104°F) / 20% ~ 85%RH
Humidity
Dimension (W x H x D) W255 X H50 X D213mm (10.04 X 1.97 X 8.39 inch)
Mechanical (Set)
Weight (With hard disks) 1.58kg 1.73kg
Dimension (W x H x D) W406 X H218 X D338mm (15.98 X 8.58 X 13.31 inch)
Mechanical (Package) Weight (With hard disks) 6.06kg 7.03kg
Rack mount kit –
English, Spanish, French, German, Italian, Polish, Portuguese, Russian,
Lauguage Turkish, Japanese, Czech, Swedish, Danish, Korean, Chinese, Netherland,
Thai, Romanian, Serbian, Croatian, Hungarian, Greek
English _93
appendix
DEFAULT SETTING
This returns the factory default settings.
The settings are made as follows;
• Use System/Load Factory Default in MENU
 The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.
Category Details Factory Default
Date YYYY-MM-DD
Time Format 24 hours
Time Zone GMT+09:00
Date/Time/Language Date/Time/Language
Time Synchronize OFF
DST OFF
System Settings Language English
ID admin
Admin
Permission New Password 4321
Management Restricted Access Backup
Setting
Auto Logout OFF
System Management System Information Broadcast Format NTSC/PAL
Video ON
Audio OFF
Camera
CH Name CAM 01 ~ CAM 04
Camera SEQ-Dwell Time 5sec
Brightness 50
Screen Setup Contrast 50
Color 50
Check Alarm Output Port OFF
Duration OFF
Device Storage Device HDD Alarm
Replace Alarm Output Port OFF
Duration OFF
Remote Device Remote Device Remote Control ON(00)
Event Display OFF
Monitor Display All
Display Position Setup 30
Monitor
Spot Out Spot Out 1 CH1 ~ CH4
Live Mode ALL
Mode
Play Mode ALL
94_ appendix
Recording Schedule Channel 1 Event

Event Record PRE Event OFF
Duration POST Event 1 min
Resolution CIF(S)
NTSC: 7 fps,
Normal Recording Frame Rate
PAL: 6.2 fps
 APPENDIX
REC Quality/ Record Quality Level 4
Recording
Resolution Resolution 4CIF(L)
NTSC: 7 fps,
Event Frame Rate
PAL: 6.2 fps
Record Quality Level 4
Setup Overwrite
Disk End Mode
Record Option Disk End Beep OFF
Auto Delete OFF
Sensor Operation OFF
Camera Camera No.
Sensor Detection
Alarm None
Duration 10 sec
Mode OFF
Sensitivity Level10(high)
Event Motion Detection Alarm None
Duration 10 sec
Motion Region All Area
Video Loss State OFF
Video Loss Detection Alarm None
Duration 10 sec
Alarm Schedule Alarm1 Event Sync
English _95
appendix
Connection Mode Static IP

Bandwidth 2Mbps
IP 192.168.1.200
Connection
Gateway 192.168.1.1
Connection Mode Subnet Mask 255.255.255.0
DNS 168.126.63.1
Protocol Type TCP
Protocol Port (TCP) 554~558
Webviewer Port 80
DDNS DDNS Site OFF
Network
Resolution CIF(S)
Live Transfer
Quality Low
Server OFF
Port 25
SMTP
Use Authentication OFF
Secure Transfer Never
Mailing Service
Event Interval 10 min
Event
Use Event Transfer OFF
Group OFF
Group
Recipient Permission OFF
96_ appendix
TROUBLESHOOTING
Symptom Countermeasures
The system does not turn on and the indicator on the  Check if the power supply system is properly connected.
front panel does not work at all.  Check the system for the input voltage from the power source.
 If the problem persists even after you have taken the above actions,
check the power supplier and replace it with a new one if neccessary.
Some channels display just a black screen even if  Check if the camera connected to the system properly displays the
 APPENDIX
they receive video sources. image. Sometimes, this problem may occur on a camera that is not
properly connected to the video source.
 Check if the camera is properly supplied with power.
 Sometimes, this problem may occur on a channel with weak video
signal from a video distributor that is connected to multiple systems. In
this case, input the video source of the camera directly into the DVR.
This may find the cause and solve the problem.
If I press the [REC] button on the front panel, the  Check if there is a free space on the HDD for the recording.
REC indicator does not flash, nor the player start  Check if the record mode is set to ON in the record mode setting.
recording.
The screen displays the logo image repeatedly.  This may occur from a problem with the main board, or the related
software is corrupt.
Contact the nearest service center for more information.
The Channel button does not work on the Live  The Channel button does not work if the current screen is in the event
screen. monitoring mode.
In the event monitoring screen, press the [ALARM] button to exit the
screen and select a channel.
The cursor will not move to the Start button when I  Check if the channel and the date that you want to play are marked
start the calendar search. with the V symbol.
Both channel and date should be checked before you can start playing
with the Start button.
When the alarm sounds, I press the [ALARM] button  Press the [MENU] button to release the alarm in the following way:
on the Remote Control to release the alarm but it 1) To release the event monitoring mode : Monitoring Mode – set the
does not work. The alarm persists and I could not set duration of the event monitoring to Off.
it off in any way. 2) To release the alarm sound : Event Record Mode - Alarm (Motion
Detection/Video Loss) – deactivate the alarm sound.
3) To release the event : Event Record Mode - Alarm (Motion Detection/
Video Loss) – set the mode to Off.
A message of “Need to reset date/time.” Is displayed  This message is displayed if there occurs a problem with the time
on the screen. setting of the internal clock or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode.  The timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current
timeline. Switch to normal mode or use the left or right button to
navigate through the time bar.
The “NO HDD” icon and an error message are  Check the HDD for connection. If the problem persists in a normal
displayed. condition, contact the nearest service center to have the HDD checked
by the service personnel.
English _97
appendix
Symptom Countermeasures
I have connected an external storage device (external  See the compatibility list of external storage devices to check if the
SATA HDD) to the DVR but the DVR seems not to connected device is supported by the DVR.
recognize it. For the compatibility list, contact the retailer where you purchased the
DVR.
If I press the ESC key in full screen mode of the

 Press the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC
WebViewer, the system does not switch to a normal
key again. The system will switch to a normal split mode.
split mode.
I found it difficult to configure the network settings if  For more information, refer to the user manual.
using the default search, backup and router settings.  If you want to check the basics of the product for a quick start, refer to
the quick start guide (backup, search).
I forgot the password.  Contact the DVR administrator for help.
Backup data is just not played by the PC or DVR.  When you are backing up data, you have choices about the player
either: PC or DVR. Make your selection before proceeding.
 If you are using the PC to play the data, the format of the backup file
should be either SEC.
 If you are using the DVR for this purpose, formatting backup files should
be done by the DVR.
My player does not switch to Live mode while in  Press the Stop [@] button on the DVR or the remote control, or click the
playback. [ ] icon on the launcher to switch to Live mode.
Recording does not work.  If your player does not display a Live image at all, that indicates
recording does not work so first check if you see an image on the
screen.
 Recording does not work if the recording settings are not properly
configured.
1) Manual Record: Press the [REC] button on the remote control to start
recording.
2) Scheduled Record: Specify a desired time in Menu – Record -
Recording Schedule. Recording will start at the specified time.
- <Continuous> Record: Recording will proceed in any conditions
at the specified time.
- <Event> Record: When an event occurs, recording will perform
only if the event is of alarm, motion detection and video loss.
If there is no event found, recording will not perform.
- <Continuous / Event> Record: If there is no event found,
Continuous recording will perform. Whereas, if an event occurs,
Event recording will perform.
The image quality of the recording data is not good.  Increase the resolution and quality level in Menu – Record – Quality /
Resolution.
1) Resolution: Select a bigger size when specifying the recording size.
(4CIF> 2CIF>CIF)
The recording image in the CIF format shows a deteriorated quality
as it is enlarged from a small-sized image.
2) Record Quality: Specify a bigger level for the recording quality.
 If you increase the resolution and the recording quality, the data size
increases accordingly. So the HDD will be filled faster. Overwriting will
overwrite the existing data so recording will proceed at a shorter
interval.
98_ appendix
OPEN SOURCE LICENSE REPORT ON THE PRODUCT
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may
obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this
product by sending email to help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost
of physically performing source distribution might be charged.
• GPL Software : linux kernel, Sysvinit, dosfstoOls, wget, msmtp, busybox, cdrtools, dvd+rw-tools, iconv, smartctl,
uboot, minicom, openssl, bash, lm_sensors
• LGPL Software : glibc, vmstat, inetutils
• OpenSSL License : OpenSSL
GNU GENERAL PUBLIC LICENSE modified by someone else and passed on, we want its
recipients to know that what they have is not the
Version 2, June 1991 original, so that any problems introduced by others will
Copyright (C) 1989, 1991 Free Software Foundation, Inc. not reflect on the original authors’ reputations.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, Finally, any free program is threatened constantly by
USA software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
Everyone is permitted to copy and distribute verbatim patent licenses, in effect making the program
copies of this license document, but changing it is not proprietary. To prevent this, we have made it clear that
allowed. any patent must be licensed for everyone’s free use or
not licensed at all. The precise terms and conditions for
Preamble copying, distribution and modification follow.
The licenses for most software are designed to take
away your freedom to share and change it. By contrast, TERMS AND CONDITIONS FOR
the GNU General Public License is intended to COPYING, DISTRIBUTION AND
guarantee your freedom to share and change free
software to make sure the software is free for all its MODIFICATION
users. This General Public License applies to most of Version 2, June 1991
the Free Software Foundation’s software and to any
other program whose authors commit to using it. Copyright (C) 1989, 1991 Free Software Foundation, Inc.
(Some other Free Software Foundation software is 51 Franklin S
covered by the GNU Lesser General Public License 0. This License applies to any program or other work
instead.) You can apply it to your programs, too. which contains a notice placed by the copyright holder
When we speak of free software, we are referring to saying it may be distributed under the terms of this
freedom, not price. Our General Public Licenses are General Public License. The “Program”, below, refers to
designed to make sure that you have the freedom to any such program or work, and a “work based on the
distribute copies of free software (and charge for this Program” means either the Program or any derivative
service if you wish), that you receive source code or can work under copyright law: that is to say, a work
get it if you want it, that you can change the software or containing the Program or a portion of it, either verbatim
use pieces of it in new free programs; and that you or with modifications and/or translated into another
know you can do these things. language. (Hereinafter, translation is included without
To protect your rights, we need to make restrictions limitation in the term “modification”.) Each licensee is
that forbid anyone to deny you these rights or to ask addressed as “you”.
you to surrender the rights. These restrictions translate Activities other than copying, distribution and
to certain responsibilities for you if you distribute copies modification are not covered by this License; they are
of the software, or if you modify it. outside its scope. The act of running the Program is not
For example, if you distribute copies of such a program, restricted, and the output from the Program is covered
whether gratis or for a fee, you must give the recipients only if its contents constitute a work based on the
all the rights that you have. You must make sure that Program (independent of having been made by running
they, too, receive or can get the source code. And you the Program). Whether that is true depends on what the
must show them these terms so they know their rights. Program does.
We protect your rights with two steps: 1. You may copy and distribute verbatim copies of the
(1) copyright the software, and (2) offer you this license Program’s source code as you receive it, in any
which gives you legal permission to copy, distribute medium, provided that you conspicuously and
and/or modify the software. appropriately publish on each copy an appropriate
Also, for each author’s protection and ours, we want to copyright notice and disclaimer of warranty; keep intact
make certain that everyone understands that there is no all the notices that refer to this License and to the
warranty for this free software. If the software is absence of any warranty; and give any other recipients

of the Program a copy of this License along with the b) Accompany it with a written offer, valid for at least
Program. three years, to give any third party, for a charge no
You may charge a fee for the physical act of transferring more than your cost of physically performing
a copy, and you may at your option offer warranty source distribution, a complete machine-readable
protection in exchange for a fee. copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2
2. You may modify your copy or copies of the Program above on a medium customarily used for software
or any portion of it, thus forming a work based on the interchange; or,
Program, and copy and distribute such modifications or c) Accompany it with the information you received as
work under the terms of Section 1 above, provided that to the offer to distribute corresponding source
you also meet all of these conditions: code. (This alternative is allowed only for
a) You must cause the modified files to carry noncommercial distribution and only if you
prominent notices stating that you changed the received the program in object code or executable
files and the date of any change. form with such an offer, in accord with Subsection
b) You must cause any work that you distribute or b above.)
publish, that in whole or in part contains or is The source code for a work means the preferred form
derived from the Program or any part thereof, to of the work for making modifications to it. For an
be licensed as a whole at no charge to all third executable work, complete source code means all the
parties under the terms of this License. source code for all modules it contains, plus any
c) If the modified program normally reads commands associated interface definition files, plus the scripts used
interactively when run, you must cause it, when to control compilation and installation of the executable.
started running for such interactive use in the However, as a special exception, the source code
most ordinary way, to print or display an distributed need not include anything that is normally
announcement including an appropriate copyright distributed (in either source or binary form) with the
notice and a notice that there is no warranty (or major components (compiler, kernel, and so on) of the
else, saying that you provide a warranty) and that operating system on which the executable runs, unless
users may redistribute the program under these that component itself accompanies the executable.
conditions, and telling the user how to view a copy If distribution of executable or object code is made by
of this License. (Exception: if the Program itself is offering access to copy from a designated place, then
interactive but does not normally print such an offering equivalent access to copy the source code
announcement, your work based on the Program from the same place counts as distribution of the
is not required to print an announcement.) source code, even though third parties are not
These requirements apply to the modified work as a compelled to copy the source along with the object
whole. If identifiable sections of that work are not code.
derived from the Program, and can be reasonably
considered independent and separate works in 4. You may not copy, modify, sublicense, or distribute
themselves, then this License, and its terms, do not the Program except as expressly provided under this
apply to those sections when you distribute them as License. Any attempt otherwise to copy, modify,
separate works. But when you distribute the same sublicense or distribute the Program is void, and will
sections as part of a whole which is a work based on automatically terminate your rights under this License.
the Program, the distribution of the whole must be on However, parties who have received copies, or rights,
the terms of this License, whose permissions for other from you under this License will not have their licenses
licensees extend to the entire whole, and thus to each terminated so long as such parties remain in full
and every part regardless of who wrote it. compliance.
Thus, it is not the intent of this section to claim rights or 5. You are not required to accept this License, since
contest your rights to work written entirely by you; rather, you have not signed it. However, nothing else grants
the intent is to exercise the right to control the distribution you permission to modify or distribute the Program or
of derivative or collective works based on the Program. its derivative works. These actions are prohibited by law
In addition, mere aggregation of another work not if you do not accept this License. Therefore, by
based on the Program with the Program (or with a work modifying or distributing the Program (or any work
based on the Program) on a volume of a storage or based on the Program), you indicate your acceptance
distribution medium does not bring the other work of this License to do so, and all its terms and conditions
under the scope of this License. for copying, distributing or modifying the Program or
works based on it.
3. You may copy and distribute the Program (or a work
based on it, under Section 2) in object code or 6. Each time you redistribute the Program (or any work
executable form under the terms of Sections 1 and 2 based on the Program), the recipient automatically
above provided that you also do one of the following: receives a license from the original licensor to copy,
a) Accompany it with the complete corresponding distribute or modify the Program subject to these terms
machine-readable source code, which must be and conditions. You may not impose any further
distributed under the terms of Sections 1 and 2 restrictions on the recipients’ exercise of the rights
above on a medium customarily used for software granted herein. You are not responsible for enforcing
interchange; or, compliance by third parties to this License.

7. If, as a consequence of a court judgment or 10. If you wish to incorporate parts of the Program into
allegation of patent infringement or for any other reason other free programs whose distribution conditions are
(not limited to patent issues), conditions are imposed on different, write to the author to ask for permission. For
you (whether by court order, agreement or otherwise) software which is copyrighted by the Free Software
that contradict the conditions of this License, they do Foundation, write to the Free Software Foundation; we
not excuse you from the conditions of this License. If sometimes make exceptions for this. Our decision will
you cannot distribute so as to satisfy simultaneously be guided by the two goals of preserving the free status
your obligations under this License and any other of all derivatives of our free software and of promoting
pertinent obligations, then as a consequence you may the sharing and reuse of software generally.
not distribute the Program at all. For example, if a
patent license would not permit royalty-free NO WARRANTY
redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only 11. BECAUSE THE PROGRAM IS LICENSED FREE OF
way you could satisfy both it and this License would be CHARGE, THERE IS NO WARRANTY FOR THE
to refrain entirely from distribution of the Program. PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
If any portion of this section is held invalid or STATED IN WRITING THE COPYRIGHT HOLDERS
unenforceable under any particular circumstance, the AND/OR OTHER PARTIES PROVIDE THE PROGRAM
balance of the section is intended to apply and the “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
section as a whole is intended to apply in other EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
circumstances. LIMITED TO, THE IMPLIED WARRANTIES OF
It is not the purpose of this section to induce you to MERCHANTABILITY AND FITNESS FOR A
infringe any patents or other property right claims or to PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
contest validity of any such claims; this section has the THE QUALITY AND PERFORMANCE OF THE
sole purpose of protecting the integrity of the free PROGRAM IS WITH YOU. SHOULD THE PROGRAM
software distribution system, which is implemented by PROVE DEFECTIVE, YOU ASSUME THE COST OF
public license practices. Many people have made ALL NECESSARY SERVICING, REPAIR OR
generous contributions to the wide range of software CORRECTION.
distributed through that system in reliance on consistent
application of that system; it is up to the author/donor 12. IN NO EVENT UNLESS REQUIRED BY
to decide if he or she is willing to distribute software APPLICABLE LAW OR AGREED TO IN WRITING WILL
through any other system and a licensee cannot ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
impose that choice. WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO
This section is intended to make thoroughly clear what YOU FOR DAMAGES, INCLUDING ANY GENERAL,
is believed to be a consequence of the rest of this SPECIAL, INCIDENTAL OR CONSEQUENTIAL
License. DAMAGES ARISING OUT OF THE USE OR INABILITY
8. If the distribution and/or use of the Program is TO USE THE PROGRAM (INCLUDING BUT NOT
restricted in certain countries either by patents or by LIMITED TO LOSS OF DATA OR DATA BEING
copyrighted interfaces, the original copyright holder who RENDERED INACCURATE OR LOSSES SUSTAINED
places the Program under this License may add an BY YOU OR THIRD PARTIES OR A FAILURE OF THE
explicit geographical distribution limitation excluding PROGRAM TO OPERATE WITH ANY OTHER
those countries, so that distribution is permitted only in PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
or among countries not thus excluded. In such case, PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
this License incorporates the limitation as if written in SUCH DAMAGES.
the body of this License.
END OF TERMS AND CONDITIONS
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License from
time to time. Such new versions will be similar in spirit to
the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If
the Program specifies a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Program does not specify a
version number of this License, you may choose any
version ever published by the Free Software
Foundation.

How to Apply These Terms to Your GNU Lesser General Public License instead of this
License.
New Programs
If you develop a new program, and you want it to be of GNU GENERAL PUBLIC LICENSE
the greatest possible use to the public, the best way to
Version 3, 29 June 2007
achieve this is to make it free software which everyone
can redistribute and change under these terms. Copyright © 2007 Free Software Foundation, Inc.
<http://fsf.org/>
To do so, attach the following notices to the program. It
is safest to attach them to the start of each source file Everyone is permitted to copy and distribute verbatim
to most effectively convey the exclusion of warranty; copies of this license document, but changing it is not
and each file should have at least the “copyright” line allowed.
and a pointer to where the full notice is found.
one line to give the program’s name and an idea of Preamble
what it does. The GNU General Public License is a free, copyleft
Copyright (C) yyyy name of author license for software and other kinds of works.
The licenses for most software and other practical
This program is free software; you can redistribute it works are designed to take away your freedom to share
and/or modify it under the terms of the GNU General and change the works. By contrast, the GNU General
Public License as published by the Free Software Public License is intended to guarantee your freedom to
Foundation; either version 2 of the License, or (at your share and change all versions of a program--to make
option) any later version. sure it remains free software for all its users. We, the
Free Software Foundation, use the GNU General Public
License for most of our software; it applies also to any
This program is distributed in the hope that it will be other work released this way by its authors. You can
useful, but WITHOUT ANY WARRANTY; without even apply it to your programs, too.
the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details. When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
You should have received a copy of the GNU General distribute copies of free software (and charge for them if
Public License along with this program; if not, write to you wish), that you receive source code or can get it if
the Free Software Foundation, Inc., 51 Franklin Street, you want it, that you can change the software or use
Fifth Floor, Boston, MA 02110-1301, USA. pieces of it in new free programs, and that you know
Also add information on how to contact you by you can do these things.
electronic and paper mail. If the program is interactive,
make it output a short notice like this when it starts in To protect your rights, we need to prevent others from
an interactive mode: denying you these rights or asking you to surrender the
Gnomovision version 69, Copyright (C) year name of rights. Therefore, you have certain responsibilities if you
author Gnomovision comes with ABSOLUTELY NO distribute copies of the software, or if you modify it:
WARRANTY; for details type ‘show w’. This is free responsibilities to respect the freedom of others.
software, and you are welcome to redistribute it under For example, if you distribute copies of such a program,
certain conditions; type ‘show c’ for details. whether gratis or for a fee, you must pass on to the
The hypothetical commands ‘show w’ and ‘show c’ recipients the same freedoms that you received. You
should show the appropriate parts of the General Public must make sure that they, too, receive or can get the
License. Of course, the commands you use may be source code. And you must show them these terms so
called something other than ‘show w’ and ‘show c’; they know their rights.
they could even be mouse-clicks or menu items--
whatever suits your program.
Developers that use the GNU GPL protect your rights
You should also get your employer (if you work as a with two steps: (1) assert copyright on the software,
programmer) or your school, if any, to sign a “copyright and (2) offer you this License giving you legal permission
disclaimer” for the program, if necessary. Here is a to copy, distribute and/or modify it.
sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in
the program ‘Gnomovision’ (which makes passes at For the developers' and authors' protection, the GPL
clearly explains that there is no warranty for this free
compilers) written by James Hacker.
software. For both users' and authors' sake, the GPL
signature of Ty Coon, 1 April 1989 Ty Coon, President requires that modified versions be marked as changed,
of Vice This General Public License does not permit so that their problems will not be attributed erroneously
incorporating your program into proprietary programs. If to authors of previous versions.
your program is a subroutine library, you may consider
it more useful to permit linking proprietary applications
with the library. If this is what you want to do, use the Some devices are designed to deny users access to

install or run modified versions of the software inside enables other parties to make or receive copies. Mere
them, although the manufacturer can do so. This is interaction with a user through a computer network,
fundamentally incompatible with the aim of protecting with no transfer of a copy, is not conveying.
users' freedom to change the software. The systematic
pattern of such abuse occurs in the area of products for
individuals to use, which is precisely where it is most An interactive user interface displays “Appropriate Legal
unacceptable. Therefore, we have designed this version Notices” to the extent that it includes a convenient and
of the GPL to prohibit the practice for those products. If prominently visible feature that (1) displays an
such problems arise substantially in other domains, we appropriate copyright notice, and (2) tells the user that
stand ready to extend this provision to those domains in there is no warranty for the work (except to the extent
future versions of the GPL, as needed to protect the that warranties are provided), that licensees may convey
freedom of users. the work under this License, and how to view a copy of
this License. If the interface presents a list of user
commands or options, such as a menu, a prominent
Finally, every program is threatened constantly by item in the list meets this criterion.
software patents. States should not allow patents to
restrict development and use of software on general-
purpose computers, but in those that do, we wish to 1. Source Code.
avoid the special danger that patents applied to a free The “source code” for a work means the preferred form
program could make it effectively proprietary. To of the work for making modifications to it. “Object code”
prevent this, the GPL assures that patents cannot be means any non-source form of a work.
used to render the program non-free.
A “Standard Interface” means an interface that either is
The precise terms and conditions for copying, an official standard defined by a recognized standards
distribution and modification follow. body, or, in the case of interfaces specified for a
particular programming language, one that is widely
TERMS AND CONDITIONS used among developers working in that language.
0. Definitions.
The “System Libraries” of an executable work include
“This License” refers to version 3 of the GNU General anything, other than the work as a whole, that (a) is
Public License. included in the normal form of packaging a Major
Component, but which is not part of that Major
“Copyright” also means copyright-like laws that apply to Component, and (b) serves only to enable use of the
other kinds of works, such as semiconductor masks. work with that Major Component, or to implement a
Standard Interface for which an implementation is
available to the public in source code form. A “Major
“The Program” refers to any copyrightable work Component”, in this context, means a major essential
licensed under this License. Each licensee is addressed component (kernel, window system, and so on) of the
as “you”. “Licensees” and “recipients” may be specific operating system (if any) on which the
individuals or organizations. executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
To “modify” a work means to copy from or adapt all or
part of the work in a fashion requiring copyright The “Corresponding Source” for a work in object code
permission, other than the making of an exact copy. form means all the source code needed to generate,
The resulting work is called a “modified version” of the install, and (for an executable work) run the object code
earlier work or a work “based on” the earlier work. and to modify the work, including scripts to control
those activities. However, it does not include the work's
A “covered work” means either the unmodified Program System Libraries, or general-purpose tools or generally
or a work based on the Program. available free programs which are used unmodified in
performing those activities but which are not part of the
work. For example, Corresponding Source includes
To “propagate” a work means to do anything with it interface definition files associated with source files for
that, without permission, would make you directly or the work, and the source code for shared libraries and
secondarily liable for infringement under applicable dynamically linked subprograms that the work is
copyright law, except executing it on a computer or specifically designed to require, such as by intimate
modifying a private copy. Propagation includes copying, data communication or control flow between those
distribution (with or without modification), making subprograms and other parts of the work.
available to the public, and in some countries other
activities as well.
The Corresponding Source need not include anything
that users can regenerate automatically from other parts
To “convey” a work means any kind of propagation that of the Corresponding Source.

The Corresponding Source for a work in source code You may charge any price or no price for each copy
form is that same work. that you convey, and you may offer support or warranty
protection for a fee.
2. Basic Permissions.
All rights granted under this License are granted for the 5. Conveying Modified Source Versions.
term of copyright on the Program, and are irrevocable You may convey a work based on the Program, or the
provided the stated conditions are met. This License modifications to produce it from the Program, in the
explicitly affirms your unlimited permission to run the form of source code under the terms of section 4,
unmodified Program. The output from running a provided that you also meet all of these conditions:
covered work is covered by this License only if the
output, given its content, constitutes a covered work. a) The work must carry prominent notices stating
This License acknowledges your rights of fair use or that you modified it, and giving a relevant date.
other equivalent, as provided by copyright law.
b) The work must carry prominent notices stating that
it is released under this License and any conditions
You may make, run and propagate covered works that added under section 7. This requirement modifies
you do not convey, without conditions so long as your the requirement in section 4 to “keep intact all
license otherwise remains in force. You may convey notices”.
covered works to others for the sole purpose of having c) You must license the entire work, as a whole,
them make modifications exclusively for you, or provide under this License to anyone who comes into
you with facilities for running those works, provided that possession of a copy. This License will therefore
you comply with the terms of this License in conveying apply, along with any applicable section 7
all material for which you do not control copyright. additional terms, to the whole of the work, and all
Those thus making or running the covered works for its parts, regardless of how they are packaged.
you must do so exclusively on your behalf, under your This License gives no permission to license the
direction and control, on terms that prohibit them from work in any other way, but it does not invalidate
making any copies of your copyrighted material outside such permission if you have separately received it.
their relationship with you. d) If the work has interactive user interfaces, each
must display Appropriate Legal Notices; however,
Conveying under any other circumstances is permitted if the Program has interactive interfaces that do
solely under the conditions stated below. Sublicensing not display Appropriate Legal Notices, your work
is not allowed; section 10 makes it unnecessary. need not make them do so.
3. Protecting Users' Legal Rights From Anti- A compilation of a covered work with other separate
Circumvention Law. and independent works, which are not by their nature
extensions of the covered work, and which are not
No covered work shall be deemed part of an effective combined with it such as to form a larger program, in or
technological measure under any applicable law fulfilling on a volume of a storage or distribution medium, is
obligations under article 11 of the WIPO copyright treaty called an “aggregate” if the compilation and its resulting
adopted on 20 December 1996, or similar laws copyright are not used to limit the access or legal rights
prohibiting or restricting circumvention of such of the compilation's users beyond what the individual
measures. works permit. Inclusion of a covered work in an
When you convey a covered work, you waive any legal aggregate does not cause this License to apply to the
power to forbid circumvention of technological other parts of the aggregate.
measures to the extent such circumvention is effected
by exercising rights under this License with respect to
the covered work, and you disclaim any intention to limit 6. Conveying Non-Source Forms.
operation or modification of the work as a means of You may convey a covered work in object code form
enforcing, against the work's users, your or third under the terms of sections 4 and 5, provided that you
parties' legal rights to forbid circumvention of also convey the machine-readable Corresponding
technological measures. Source under the terms of this License, in one of these
ways:
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program's a) Convey the object code in, or embodied in, a
source code as you receive it, in any medium, provided physical product (including a physical distribution
that you conspicuously and appropriately publish on medium), accompanied by the Corresponding
each copy an appropriate copyright notice; keep intact Source fixed on a durable physical medium
all notices stating that this License and any non- customarily used for software interchange.
permissive terms added in accord with section 7 apply b) Convey the object code in, or embodied in, a
to the code; keep intact all notices of the absence of physical product (including a physical distribution
any warranty; and give all recipients a copy of this medium), accompanied by a written offer, valid for
License along with the Program. at least three years and valid for as long as you

offer spare parts or customer support for that “Installation Information” for a User Product means any
product model, to give anyone who possesses methods, procedures, authorization keys, or other
the object code either (1) a copy of the information required to install and execute modified
Corresponding Source for all the software in the versions of a covered work in that User Product from a
product that is covered by this License, on a modified version of its Corresponding Source. The
durable physical medium customarily used for information must suffice to ensure that the continued
software interchange, for a price no more than functioning of the modified object code is in no case
your reasonable cost of physically performing this prevented or interfered with solely because modification
conveying of source, or (2) access to copy the has been made.
Corresponding Source from a network server at
no charge.
If you convey an object code work under this section in,
c) Convey individual copies of the object code with a or with, or specifically for use in, a User Product, and
copy of the written offer to provide the the conveying occurs as part of a transaction in which
Corresponding Source. This alternative is allowed the right of possession and use of the User Product is
only occasionally and noncommercially, and only if transferred to the recipient in perpetuity or for a fixed
you received the object code with such an offer, in term (regardless of how the transaction is
accord with subsection 6b. characterized), the Corresponding Source conveyed
d) Convey the object code by offering access from a under this section must be accompanied by the
designated place (gratis or for a charge), and offer Installation Information. But this requirement does not
equivalent access to the Corresponding Source in apply if neither you nor any third party retains the ability
the same way through the same place at no to install modified object code on the User Product (for
further charge. You need not require recipients to example, the work has been installed in ROM).
copy the Corresponding Source along with the
object code. If the place to copy the object code
is a network server, the Corresponding Source The requirement to provide Installation Information does
may be on a different server (operated by you or a not include a requirement to continue to provide
third party) that supports equivalent copying support service, warranty, or updates for a work that
facilities, provided you maintain clear directions has been modified or installed by the recipient, or for
next to the object code saying where to find the the User Product in which it has been modified or
Corresponding Source. Regardless of what server installed. Access to a network may be denied when the
hosts the Corresponding Source, you remain modification itself materially and adversely affects the
obligated to ensure that it is available for as long operation of the network or violates the rules and
as needed to satisfy these requirements. protocols for communication across the network.
e) Convey the object code using peer-to-peer
transmission, provided you inform other peers Corresponding Source conveyed, and Installation
where the object code and Corresponding Source Information provided, in accord with this section must
of the work are being offered to the general public be in a format that is publicly documented (and with an
at no charge under subsection 6d. implementation available to the public in source code
form), and must require no special password or key for
A separable portion of the object code, whose source unpacking, reading or copying.
code is excluded from the Corresponding Source as a
System Library, need not be included in conveying the 7. Additional Terms.
object code work.
“Additional permissions” are terms that supplement the
terms of this License by making exceptions from one or
A “User Product” is either (1) a “consumer product”, more of its conditions. Additional permissions that are
which means any tangible personal property which is applicable to the entire Program shall be treated as
normally used for personal, family, or household though they were included in this License, to the extent
purposes, or (2) anything designed or sold for that they are valid under applicable law. If additional
incorporation into a dwelling. In determining whether a permissions apply only to part of the Program, that part
product is a consumer product, doubtful cases shall be may be used separately under those permissions, but
resolved in favor of coverage. For a particular product the entire Program remains governed by this License
received by a particular user, “normally used” refers to a without regard to the additional permissions.
typical or common use of that class of product,
regardless of the status of the particular user or of the
way in which the particular user actually uses, or When you convey a copy of a covered work, you may
expects or is expected to use, the product. A product is at your option remove any additional permissions from
a consumer product regardless of whether the product that copy, or from any part of it. (Additional permissions
has substantial commercial, industrial or non-consumer may be written to require their own removal in certain
uses, unless such uses represent the only significant cases when you modify the work.) You may place
mode of use of the product. additional permissions on material, added by you to a
covered work, for which you have or can give
appropriate copyright permission.

Notwithstanding any other provision of this License, for However, if you cease all violation of this License, then
material you add to a covered work, you may (if your license from a particular copyright holder is
authorized by the copyright holders of that material) reinstated (a) provisionally, unless and until the copyright
supplement the terms of this License with terms: holder explicitly and finally terminates your license, and
(b) permanently, if the copyright holder fails to notify you
a) Disclaiming warranty or limiting liability differently of the violation by some reasonable means prior to 60
from the terms of sections 15 and 16 of this days after the cessation.
License; or
b) Requiring preservation of specified reasonable Moreover, your license from a particular copyright
legal notices or author attributions in that material holder is reinstated permanently if the copyright holder
or in the Appropriate Legal Notices displayed by notifies you of the violation by some reasonable means,
works containing it; or this is the first time you have received notice of violation
c) Prohibiting misrepresentation of the origin of that of this License (for any work) from that copyright holder,
material, or requiring that modified versions of and you cure the violation prior to 30 days after your
such material be marked in reasonable ways as receipt of the notice.
different from the original version; or
d) Limiting the use for publicity purposes of names of Termination of your rights under this section does not
licensors or authors of the material; or terminate the licenses of parties who have received
e) Declining to grant rights under trademark law for copies or rights from you under this License. If your
use of some trade names, trademarks, or service rights have been terminated and not permanently
marks; or reinstated, you do not qualify to receive new licenses for
f) Requiring indemnification of licensors and authors the same material under section 10.
of that material by anyone who conveys the
material (or modified versions of it) with contractual
assumptions of liability to the recipient, for any 9. Acceptance Not Required for Having Copies.
liability that these contractual assumptions directly You are not required to accept this License in order to
impose on those licensors and authors. receive or run a copy of the Program. Ancillary
propagation of a covered work occurring solely as a
consequence of using peer-to-peer transmission to
All other non-permissive additional terms are receive a copy likewise does not require acceptance.
considered “further restrictions” within the meaning of However, nothing other than this License grants you
section 10. If the Program as you received it, or any part permission to propagate or modify any covered work.
of it, contains a notice stating that it is governed by this These actions infringe copyright if you do not accept
License along with a term that is a further restriction, this License. Therefore, by modifying or propagating a
you may remove that term. If a license document covered work, you indicate your acceptance of this
contains a further restriction but permits relicensing or License to do so.
conveying under this License, you may add to a
covered work material governed by the terms of that
license document, provided that the further restriction 10. Automatic Licensing of Downstream Recipients.
does not survive such relicensing or conveying. Each time you convey a covered work, the recipient
automatically receives a license from the original
If you add terms to a covered work in accord with this licensors, to run, modify and propagate that work,
section, you must place, in the relevant source files, a subject to this License. You are not responsible for
statement of the additional terms that apply to those enforcing compliance by third parties with this License.
files, or a notice indicating where to find the applicable
terms. An “entity transaction” is a transaction transferring
control of an organization, or substantially all assets of
Additional terms, permissive or non-permissive, may be one, or subdividing an organization, or merging
stated in the form of a separately written license, or organizations. If propagation of a covered work results
stated as exceptions; the above requirements apply from an entity transaction, each party to that transaction
either way. who receives a copy of the work also receives whatever
licenses to the work the party's predecessor in interest
had or could give under the previous paragraph, plus a
8. Termination. right to possession of the Corresponding Source of the
You may not propagate or modify a covered work work from the predecessor in interest, if the
except as expressly provided under this License. Any predecessor has it or can get it with reasonable efforts.
attempt otherwise to propagate or modify it is void, and
will automatically terminate your rights under this You may not impose any further restrictions on the
License (including any patent licenses granted under exercise of the rights granted or affirmed under this
the third paragraph of section 11). License. For example, you may not impose a license
fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate

litigation (including a cross-claim or counterclaim in a A patent license is “discriminatory” if it does not include
lawsuit) alleging that any patent claim is infringed by within the scope of its coverage, prohibits the exercise
making, using, selling, offering for sale, or importing the of, or is conditioned on the non-exercise of one or more
Program or any portion of it. of the rights that are specifically granted under this
License. You may not convey a covered work if you are
a party to an arrangement with a third party that is in the
11. Patents. business of distributing software, under which you make
A “contributor” is a copyright holder who authorizes use payment to the third party based on the extent of your
under this License of the Program or a work on which activity of conveying the work, and under which the third
the Program is based. The work thus licensed is called party grants, to any of the parties who would receive the
the contributor's “contributor version”. covered work from you, a discriminatory patent license
(a) in connection with copies of the covered work
A contributor's “essential patent claims” are all patent conveyed by you (or copies made from those copies), or
claims owned or controlled by the contributor, whether (b) primarily for and in connection with specific products
already acquired or hereafter acquired, that would be or compilations that contain the covered work, unless
infringed by some manner, permitted by this License, of you entered into that arrangement, or that patent license
making, using, or selling its contributor version, but do was granted, prior to 28 March 2007.
not include claims that would be infringed only as a
consequence of further modification of the contributor Nothing in this License shall be construed as excluding
version. For purposes of this definition, “control” includes or limiting any implied license or other defenses to
the right to grant patent sublicenses in a manner infringement that may otherwise be available to you
consistent with the requirements of this License. under applicable patent law.
Each contributor grants you a non-exclusive, 12. No Surrender of Others' Freedom.

worldwide, royalty-free patent license under the If conditions are imposed on you (whether by court
contributor's essential patent claims, to make, use, sell, order, agreement or otherwise) that contradict the
offer for sale, import and otherwise run, modify and conditions of this License, they do not excuse you from
propagate the contents of its contributor version. the conditions of this License. If you cannot convey a
covered work so as to satisfy simultaneously your
In the following three paragraphs, a “patent license” is obligations under this License and any other pertinent
any express agreement or commitment, however obligations, then as a consequence you may not
denominated, not to enforce a patent (such as an convey it at all. For example, if you agree to terms that
express permission to practice a patent or covenant not obligate you to collect a royalty for further conveying
to sue for patent infringement). To “grant” such a patent from those to whom you convey the Program, the only
license to a party means to make such an agreement or way you could satisfy both those terms and this License
commitment not to enforce a patent against the party. would be to refrain entirely from conveying the Program.
If you convey a covered work, knowingly relying on a 13. Use with the GNU Affero General Public
patent license, and the Corresponding Source of the License.
work is not available for anyone to copy, free of charge Notwithstanding any other provision of this License, you
and under the terms of this License, through a publicly have permission to link or combine any covered work
available network server or other readily accessible with a work licensed under version 3 of the GNU Affero
means, then you must either (1) cause the Corresponding General Public License into a single combined work,
Source to be so available, or (2) arrange to deprive and to convey the resulting work. The terms of this
yourself of the benefit of the patent license for this License will continue to apply to the part which is the
particular work, or (3) arrange, in a manner consistent covered work, but the special requirements of the GNU
with the requirements of this License, to extend the Affero General Public License, section 13, concerning
patent license to downstream recipients. “Knowingly interaction through a network will apply to the
relying” means you have actual knowledge that, but for combination as such.
the patent license, your conveying the covered work in a
country, or your recipient's use of the covered work in a
country, would infringe one or more identifiable patents in 14. Revised Versions of this License.
that country that you have reason to believe are valid. The Free Software Foundation may publish revised and/
or new versions of the GNU General Public License
from time to time. Such new versions will be similar in
If, pursuant to or in connection with a single transaction spirit to the present version, but may differ in detail to
or arrangement, you convey, or propagate by procuring address new problems or concerns.
conveyance of, a covered work, and grant a patent
license to some of the parties receiving the covered
work authorizing them to use, propagate, modify or Each version is given a distinguishing version number. If
convey a specific copy of the covered work, then the the Program specifies that a certain numbered version
patent license you grant is automatically extended to all of the GNU General Public License “or any later version”
recipients of the covered work and works based on it. applies to it, you have the option of following the terms

and conditions either of that numbered version or of any END OF TERMS AND CONDITIONS
later version published by the Free Software
Foundation. If the Program does not specify a version GNU LESSER GENERAL PUBLIC
number of the GNU General Public License, you may
choose any version ever published by the Free Software LICENSE
Foundation. Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation,
If the Program specifies that a proxy can decide which Inc.
future versions of the GNU General Public License can 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
be used, that proxy's public statement of acceptance of USA
a version permanently authorizes you to choose that Everyone is permitted to copy and distribute verbatim
version for the Program. copies of this license document, but changing it is not
allowed.
Later license versions may give you additional or
different permissions. However, no additional [This is the first released version of the Lesser GPL.
obligations are imposed on any author or copyright It also counts as the successor of the GNU Library Public
holder as a result of your choosing to follow a later License, version 2, hence the version number 2.1.]
version.
Preamble
15. Disclaimer of Warranty.
The licenses for most software are designed to take
THERE IS NO WARRANTY FOR THE PROGRAM, TO away your freedom to share and change it. By contrast,
THE EXTENT PERMITTED BY APPLICABLE LAW. the GNU General Public Licenses are intended to
EXCEPT WHEN OTHERWISE STATED IN WRITING guarantee your freedom to share and change free
THE COPYRIGHT HOLDERS AND/OR OTHER software to make sure the software is free for all its
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT users.
WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE This license, the Lesser General Public License, applies
IMPLIED WARRANTIES OF MERCHANTABILITY AND to some specially designated software packages--
FITNESS FOR A PARTICULAR PURPOSE. THE typically libraries--of the Free Software Foundation and
ENTIRE RISK AS TO THE QUALITY AND other authors who decide to use it. You can use it too,
PERFORMANCE OF THE PROGRAM IS WITH YOU. but we suggest you first think carefully about whether
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU this license or the ordinary General Public License is the
ASSUME THE COST OF ALL NECESSARY better strategy to use in any particular case, based on
SERVICING, REPAIR OR CORRECTION. the explanations below.
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses
16. Limitation of Liability. are designed to make sure that you have the freedom
IN NO EVENT UNLESS REQUIRED BY APPLICABLE to distribute copies of free software (and charge for this
LAW OR AGREED TO IN WRITING WILL ANY service if you wish); that you receive source code or can
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO get it if you want it; that you can change the software
MODIFIES AND/OR CONVEYS THE PROGRAM AS and use pieces of it in new free programs; and that you
PERMITTED ABOVE, BE LIABLE TO YOU FOR are informed that you can do these things.
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, To protect your rights, we need to make restrictions
INCIDENTAL OR CONSEQUENTIAL DAMAGES that forbid distributors to deny you these rights or to ask
ARISING OUT OF THE USE OR INABILITY TO USE you to surrender these rights. These restrictions
THE PROGRAM (INCLUDING BUT NOT LIMITED TO translate to certain responsibilities for you if you
LOSS OF DATA OR DATA BEING RENDERED distribute copies of the library or if you modify it.
INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM For example, if you distribute copies of the library,
TO OPERATE WITH ANY OTHER PROGRAMS), EVEN whether gratis or for a fee, you must give the recipients
IF SUCH HOLDER OR OTHER PARTY HAS BEEN all the rights that we gave you. You must make sure
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. that they, too, receive or can get the source code. If you
link other code with the library, you must provide
complete object files to the recipients, so that they can
17. Interpretation of Sections 15 and 16. relink them with the library after making changes to the
If the disclaimer of warranty and limitation of liability library and recompiling it. And you must show them
provided above cannot be given local legal effect these terms so they know their rights.
according to their terms, reviewing courts shall apply We protect your rights with a two-step method: (1) we
local law that most closely approximates an absolute copyright the library, and (2) we offer you this license,
waiver of all civil liability in connection with the Program, which gives you legal permission to copy, distribute
unless a warranty or assumption of liability accompanies and/or modify the library.
a copy of the Program in return for a fee.

To protect each distributor, we want to make it very The precise terms and conditions for copying,
clear that there is no warranty for the free library. Also, if distribution and modification follow. Pay close attention
the library is modified by someone else and passed on, to the difference between a “work based on the library”
the recipients should know that what they have is not and a “work that uses the library”. The former contains
the original version, so that the original author’s code derived from the library, whereas the latter must
reputation will not be affected by problems that might be combined with the library in order to run.
be introduced by others.
Finally, software patents pose a constant threat to the TERMS AND CONDITIONS FOR
existence of any free program. We wish to make sure COPYING, DISTRIBUTION AND
that a company cannot effectively restrict the users of a
free program by obtaining a restrictive license from a MODIFICATION
patent holder. Therefore, we insist that any patent 0. This License Agreement applies to any software
license obtained for a version of the library must be library or other program which contains a notice placed
consistent with the full freedom of use specified in this by the copyright holder or other authorized party saying
license. it may be distributed under the terms of this Lesser
Most GNU software, including some libraries, is covered General Public License (also called “this License”). Each
by the ordinary GNU General Public License. This licensee is addressed as “you”.
license, the GNU Lesser General Public License, applies A “library” means a collection of software functions and/
to certain designated libraries, and is quite different from or data prepared so as to be conveniently linked with
the ordinary General Public License. We use this license application programs (which use some of those
for certain libraries in order to permit linking those functions and data) to form executables.
libraries into non-free programs.
The “Library”, below, refers to any such software library
When a program is linked with a library, whether or work which has been distributed under these terms.
statically or using a shared library, the combination of A “work based on the Library” means either the Library
the two is legally speaking a combined work, a or any derivative work under copyright law: that is to
derivative of the original library. The ordinary General say, a work containing the Library or a portion of it,
Public License therefore permits such linking only if the either verbatim or with modifications and/or translated
entire combination fits its criteria of freedom. The Lesser straightforwardly into another language. (Hereinafter,
General Public License permits more lax criteria for translation is included without limitation in the term
linking other code with the library. “modification”.)
We call this license the “Lesser” General Public License “Source code” for a work means the preferred form of
because it does Less to protect the user’s freedom the work for making modifications to it. For a library,
than the ordinary General Public License. It also complete source code means all the source code for all
provides other free software developers Less of an modules it contains, plus any associated interface
advantage over competing non-free programs. These definition files, plus the scripts used to control
disadvantages are the reason we use the ordinary compilation and installation of the library.
General Public License for many libraries. However, the
Lesser license provides advantages in certain special Activities other than copying, distribution and
circumstances. modification are not covered by this License; they are
outside its scope. The act of running a program using
For example, on rare occasions, there may be a special the Library is not restricted, and output from such a
need to encourage the widest possible use of a certain program is covered only if its contents constitute a work
library, so that it becomes a de-facto standard. To based on the Library (independent of the use of the
achieve this, non-free programs must be allowed to use Library in a tool for writing it). Whether that is true
the library. A more frequent case is that a free library depends on what the Library does and what the
does the same job as widely used non-free libraries. In program that uses the Library does.
this case, there is little to gain by limiting the free library
to free software only, so we use the Lesser General
Public License. 1. You may copy and distribute verbatim copies of the
In other cases, permission to use a particular library in Library’s complete source code as you receive it, in any
non-free programs enables a greater number of people medium, provided that you conspicuously and
to use a large body of free software. For example, appropriately publish on each copy an appropriate
permission to use the GNU C Library in non-free copyright notice and disclaimer of warranty; keep intact
programs enables many more people to use the whole all the notices that refer to this License and to the
GNU operating system, as well as its variant, the GNU/ absence of any warranty; and distribute a copy of this
Linux operating system. License along with the Library.
Although the Lesser General Public License is Less You may charge a fee for the physical act of transferring
protective of the users’ freedom, it does ensure that the a copy, and you may at your option offer warranty
user of a program that is linked with the Library has the protection in exchange for a fee.
freedom and the wherewithal to run that program using
a modified version of the Library.

2. You may modify your copy or copies of the Library or Once this change is made in a given copy, it is
any portion of it, thus forming a work based on the irreversible for that copy, so the ordinary GNU General
Library, and copy and distribute such modifications or Public License applies to all subsequent copies and
work under the terms of Section 1 above, provided that derivative works made from that copy.
you also meet all of these conditions: This option is useful when you wish to copy part of the
a) The modified work must itself be a software code of the Library into a program that is not a library.
library.
b) You must cause the files modified to carry
prominent notices stating that you changed the 4. You may copy and distribute the Library (or a portion
files and the date of any change. or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
c) You must cause the whole of the work to be above provided that you accompany it with the
licensed at no charge to all third parties under the complete corresponding machine-readable source
terms of this License. code, which must be distributed under the terms of
d) If a facility in the modified Library refers to a Sections 1 and 2 above on a medium customarily used
function or a table of data to be supplied by an for software interchange.
application program that uses the facility, other
than as an argument passed when the facility is If distribution of object code is made by offering access
invoked, then you must make a good faith effort to to copy from a designated place, then offering
ensure that, in the event an application does not equivalent access to copy the source code from the
supply such function or table, the facility still same place satisfies the requirement to distribute the
operates, and performs whatever part of its source code, even though third parties are not
purpose remains meaningful. compelled to copy the source along with the object
code.
(For example, a function in a library to compute square
roots has a purpose that is entirely well-defined
independent of the application. Therefore, Subsection 5. A program that contains no derivative of any portion
2d requires that any application-supplied function or of the Library, but is designed to work with the Library
table used by this function must be optional: if the by being compiled or linked with it, is called a “work that
application does not supply it, the square root function uses the Library”. Such a work, in isolation, is not a
must still compute square roots.) derivative work of the Library, and therefore falls outside
These requirements apply to the modified work as a the scope of this License.
whole. If identifiable sections of that work are not However, linking a “work that uses the Library” with the
derived from the Library, and can be reasonably Library creates an executable that is a derivative of the
considered independent and separate works in Library (because it contains portions of the Library),
themselves, then this License, and its terms, do not rather than a “work that uses the library”. The
apply to those sections when you distribute them as executable is therefore covered by this License. Section
separate works. But when you distribute the same 6 states terms for distribution of such executables.
sections as part of a whole which is a work based on When a “work that uses the Library” uses material from
the Library, the distribution of the whole must be on the a header file that is part of the Library, the object code
terms of this License, whose permissions for other for the work may be a derivative work of the Library
licensees extend to the entire whole, and thus to each even though the source code is not. Whether this is true
and every part regardless of who wrote it. is especially significant if the work can be linked without
Thus, it is not the intent of this section to claim rights or the Library, or if the work is itself a library. The threshold
contest your rights to work written entirely by you; for this to be true is not precisely defined by law.
rather, the intent is to exercise the right to control the If such an object file uses only numerical parameters,
distribution of derivative or collective works based on data structure layouts and accessors, and small macros
the Library. and small inline functions (ten lines or less in length),
In addition, mere aggregation of another work not then the use of the object file is unrestricted, regardless
based on the Library with the Library (or with a work of whether it is legally a derivative work. (Executables
based on the Library) on a volume of a storage or containing this object code plus portions of the Library
distribution medium does not bring the other work will still fall under Section 6.)
under the scope of this License. Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
3. You may opt to apply the terms of the ordinary GNU terms of Section 6. Any executables containing that
General Public License instead of this License to a given work also fall under Section 6, whether or not they are
copy of the Library. To do this, you must alter all the linked directly with the Library itself.
notices that refer to this License, so that they refer to
the ordinary GNU General Public License, version 2, 6. As an exception to the Sections above, you may also
instead of to this License. (If a newer version than combine or link a “work that uses the Library” with the
version 2 of the ordinary GNU General Public License Library to produce a work containing portions of the
has appeared, then you can specify that version instead Library, and distribute that work under terms of your
if you wish.) Do not make any other change in these choice, provided that the terms permit modification of
notices.

the work for the customer’s own use and reverse 7. You may place library facilities that are a work based
engineering for debugging such modifications. on the Library side-by-side in a single library together
You must give prominent notice with each copy of the with other library facilities not covered by this License,
work that the Library is used in it and that the Library and distribute such a combined library, provided that
and its use are covered by this License. You must the separate distribution of the work based on the
supply a copy of this License. If the work during Library and of the other library facilities is otherwise
execution displays copyright notices, you must include permitted, and provided that you do these two things:
the copyright notice for the Library among them, as well a) Accompany the combined library with a copy of
as a reference directing the user to the copy of this the same work based on the Library, uncombined
License. Also, you must do one of these things: with any other library facilities. This must be
a) Accompany the work with the complete distributed under the terms of the Sections above.
corresponding machine-readable source code for b) Give prominent notice with the combined library of
the Library including whatever changes were used the fact that part of it is a work based on the
in the work (which must be distributed under Library, and explaining where to find the
Sections 1 and 2 above); and, if the work is an accompanying uncombined form of the same work.
executable linked with the Library, with the
complete machine readable “work that uses the 8. You may not copy, modify, sublicense, link with, or
Library”, as object code and/or source code, so distribute the Library except as expressly provided
that the user can modify the Library and then under this License. Any attempt otherwise to copy,
relink to produce a modified executable containing modify, sublicense, link with, or distribute the Library is
the modified Library. (It is understood that the user void, and will automatically terminate your rights under
who changes the contents of definitions files in the this License. However, parties who have received
Library will not necessarily be able to recompile copies, or rights, from you under this License will not
the application to use the modified definitions.) have their licenses terminated so long as such parties
b) Use a suitable shared library mechanism for linking remain in full compliance.
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather 9. You are not required to accept this License, since you
than copying library functions into the executable, have not signed it. However, nothing else grants you
and (2) will operate properly with a modified permission to modify or distribute the Library or its
version of the library, if the user installs one, as derivative works. These actions are prohibited by law if
long as the modified version is interface- you do not accept this License. Therefore, by modifying
compatible with the version that the work was or distributing the Library (or any work based on the
made with. Library), you indicate your acceptance of this License to
c) Accompany the work with a written offer, valid for do so, and all its terms and conditions for copying,
at least three years, to give the same user the distributing or modifying the Library or works based on it.
materials specified in Subsection 6a, above, for a
charge no more than the cost of performing this 10. Each time you redistribute the Library (or any work
distribution. based on the Library), the recipient automatically
d) If distribution of the work is made by offering receives a license from the original licensor to copy,
access to copy from a designated place, offer distribute, link with or modify the Library subject to
equivalent access to copy the above specified these terms and conditions. You may not impose any
materials from the same place. further restrictions on the recipients’ exercise of the
e) Verify that the user has already received a copy of rights granted herein. You are not responsible for
these materials or that you have already sent this enforcing compliance by third parties with this License.
user a copy.
For an executable, the required form of the “work that 11. If, as a consequence of a court judgment or
uses the Library” must include any data and utility allegation of patent infringement or for any other reason
programs needed for reproducing the executable from (not limited to patent issues), conditions are imposed on
it. However, as a special exception, the materials to be you (whether by court order, agreement or otherwise)
distributed need not include anything that is normally that contradict the conditions of this License, they do
distributed (in either source or binary form) with the not excuse you from the conditions of this License. If
major components (compiler, kernel, and so on) of the you cannot distribute so as to satisfy simultaneously
operating system on which the executable runs, unless your obligations under this License and any other
that component itself accompanies the executable. pertinent obligations, then as a consequence you may
It may happen that this requirement contradicts the not distribute the Library at all. For example, if a patent
license restrictions of other proprietary libraries that do license would not permit royalty free redistribution of the
not normally accompany the operating system. Such a Library by all those who receive copies directly or
contradiction means you cannot use both them and the indirectly through you, then the only way you could
Library together in an executable that you distribute. satisfy both it and this License would be to refrain
entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
under any particular circumstance, the balance of the LIMITED TO, THE IMPLIED WARRANTIES OF
section is intended to apply, and the section as a whole is MERCHANTABILITY AND FITNESS FOR A
intended to apply in other circumstances. PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
It is not the purpose of this section to induce you to THE QUALITY AND PERFORMANCE OF THE LIBRARY
infringe any patents or other property right claims or to IS WITH YOU. SHOULD THE LIBRARY PROVE
contest validity of any such claims; this section has the DEFECTIVE, YOU ASSUME THE COST OF ALL
sole purpose of protecting the integrity of the free software NECESSARY SERVICING, REPAIR OR CORRECTION.
distribution system which is implemented by public license
practices. Many people have made generous 16. IN NO EVENT UNLESS REQUIRED BY
contributions to the wide range of software distributed APPLICABLE LAW OR AGREED TO IN WRITING WILL
through that system in reliance on consistent application ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
of that system; it is up to the author/donor to decide if he WHO MAY MODIFY AND/OR REDISTRIBUTE THE
or she is willing to distribute software through any other LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU
system and a licensee cannot impose that choice. FOR DAMAGES, INCLUDING ANY GENERAL,
This section is intended to make thoroughly clear what is SPECIAL, INCIDENTAL OR CONSEQUENTIAL
believed to be a consequence of the rest of this License. DAMAGES ARISING OUT OF THE USE OR INABILITY
12. If the distribution and/or use of the Library is TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED
restricted in certain countries either by patents or by TO LOSS OF DATA OR DATA BEING RENDERED
copyrighted interfaces, the original copyright holder who INACCURATE OR LOSSES SUSTAINED BY YOU OR
places the Library under this License may add an THIRD PARTIES OR A FAILURE OF THE LIBRARY TO
explicit geographical distribution limitation excluding OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
those countries, so that distribution is permitted only in SUCH HOLDER OR OTHER PARTY HAS BEEN
or among countries not thus excluded. In such case, ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
this License incorporates the limitation as if written in
the body of this License. END OF TERMS AND CONDITIONS
13. The Free Software Foundation may publish revised How to Apply These Terms to Your
and/or new versions of the Lesser General Public New Libraries
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in If you develop a new library, and you want it to be of the
detail to address new problems or concerns. greatest possible use to the public, we recommend
making it free software that everyone can redistribute
Each version is given a distinguishing version number. If
and change. You can do so by permitting redistribution
the Library specifies a version number of this License
under these terms (or, alternatively, under the terms of
which applies to it and “any later version”, you have the
the ordinary General Public License).
option of following the terms and conditions either of
that version or of any later version published by the Free To apply these terms, attach the following notices to the
Software Foundation. If the Library does not specify a library. It is safest to attach them to the start of each
license version number, you may choose any version source file to most effectively convey the exclusion of
ever published by the Free Software Foundation. warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is
found. one line to give the library’s name and an idea of
14. If you wish to incorporate parts of the Library into what it does.
other free programs whose distribution conditions are
Copyright (C) year name of author
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software This library is free software; you can redistribute it and/
Foundation; we sometimes make exceptions for this. or modify it under the terms of the GNU Lesser General
Our decision will be guided by the two goals of Public License as published by the Free Software
preserving the free status of all derivatives of our free Foundation; either version 2.1 of the License, or (at your
software and of promoting the sharing and reuse of option) any later version.
software generally.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the
NO WARRANTY implied warranty of MERCHANTABILITY or FITNESS
15. BECAUSE THE LIBRARY IS LICENSED FREE OF FOR A PARTICULAR PURPOSE. See the GNU Lesser
CHARGE, THERE IS NO WARRANTY FOR THE General Public License for more details.
LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE You should have received a copy of the GNU Lesser
STATED IN WRITING THE COPYRIGHT HOLDERS General Public License along with this library; if not,
AND/OR OTHER PARTIES PROVIDE THE LIBRARY
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

write to the Free Software Foundation, Inc., 51 Franklin TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
Street, Fifth Floor, Boston, MA 02110-1301 USA Also ARISING IN ANY WAY OUT OF THE USE OF THIS
add information on how to contact you by electronic SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
and paper mail. OF SUCH DAMAGE.This product includes
You should also get your employer (if you work as a cryptographic software written by Eric Young (eay@
programmer) or your school, if any, to sign a “copyright cryptsoft.com). This product includes software written
disclaimer” for the library, if necessary. Here is a by Tim Hudson (tjh@cryptsoft.com).
sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in Original SSLeay License
the library ‘Frob’ (a library for tweaking knobs) written by Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.
James Random Hacker. com) All rights reserved. This package is an SSL
signature of Ty Coon, 1 April 1990 Ty Coon, President implementation written by Eric Young (eay@cryptsoft.
of Vice. com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial
OpenSSL LICENSE and non-commercial use as long as the following
conditions are aheared to. The following conditions
Copyright (c) 1998-2006 The OpenSSL Project. All apply to all code found in this distribution, be it the RC4,
rights reserved. Redistribution and use in source and RSA, lhash, DES, etc., code; not just the SSL code.
binary forms, with or without modification, are permitted The SSL documentation included with this distribution is
provided that the following conditions are met: covered by the same copyright terms except that the
1. Redistributions of source code must retain the above holder is Tim Hudson (tjh@cryptsoft.com).
copyright notice, this list of conditions and the following Copyright remains Eric Young’s, and as such any
disclaimer. Copyright notices in the code are not to be removed.
2. Redistributions in binary form must reproduce the If this package is used in a product, Eric Young should
above copyright notice, this list of conditions and the be given attribution as the author of the parts of the
following disclaimer in the documentation and/or other library used. This can be in the form of a textual
materials provided with the distribution. message at program startup or in documentation
3. All advertising materials mentioning features or use of (online or textual) provided with the package.
this software must display the following Redistribution and use in source and binary forms, with
acknowledgment: “This product includes software or without modification, are permitted provided that the
developed by the OpenSSL Project for use in the following conditions are met:
OpenSSL Toolkit. (http://www.openssl.org/)” 1. Redistributions of source code must retain the
4. The names “OpenSSL Toolkit” and “OpenSSL copyright notice, this list of conditions and the following
Project” must not be used to endorse or promote disclaimer.
products derived from this software without prior written 2. Redistributions in binary form must reproduce the
permission. For written permission, please contact above copyright notice, this list of conditions and the
openssl-core@openssl.org. following disclaimer in the documentation and/or other
5. Products derived from this software may not be materials provided with the distribution.
called “OpenSSL” nor may “OpenSSL” appear in their 3. All advertising materials mentioning features or use of
names without prior written permission of the OpenSSL this software must display the following
Project. acknowledgement: “This product includes
6. Redistributions of any form whatsoever must retain cryptographic software written by Eric Young (eay@
the following acknowledgment: “This product includes cryptsoft.com)” The word ‘cryptographic’ can be left out
software developed by the OpenSSL Project for use in if the rouines from the library being used are not
the OpenSSL Toolkit (http://www.openssl.org/)” cryptographic related :-).
4. If you include any Windows specific code (or a
derivative thereof) from the apps directory (application
THIS SOFTWARE IS PROVIDED BY THE OpenSSL code) you must include an acknowledgement: “This
PROJECT ‘‘AS IS’’ AND ANY EXPRESSED OR product includes software written by Tim Hudson (tjh@
IMPLIED WARRANTIES, INCLUDING, BUT NOT cryptsoft.com)”
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES,
EVENT SHALL THE OpenSSL PROJECT OR ITS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, WARRANTIES OF MERCHANTABILITY AND FITNESS
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
LIMITED TO, PROCUREMENT OF SUBSTITUTE BE LIABLE FOR ANY DIRECT, INDIRECT,
GOODS OR SERVICES; LOSS OF USE, DATA, OR INCIDENTAL, SPECIAL, EXEMPLARY, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
CAUSED AND ON ANY THEORY OF LIABILITY, LIMITED TO, PROCUREMENT OF SUBSTITUTE
WHETHER IN CONTRACT, STRICT LIABILITY, OR GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.The licence and distribution terms
for any publically available version or derivative of this
code cannot be changed. i.e. this code cannot simply
be copied and put under another distribution licence
[including the GNU Public Licence.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.

SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD.

100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Chertsey, Surrey, UNITED KINGDOM KT16 OPS
Fax : +1-201-373-0124 TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungsv.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com

4 Channel DVR: User Manual

Uploaded by

Copyright:

Available Formats

4 Channel DVR: User Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4 Channel DVR: User Manual

Uploaded by

Copyright:

Available Formats

4 CHANNEL DVR

User Manual SDE-3001/3003

Downloaded from www.Manualslib.com manuals search engine

 Design and specifications are subject to change without prior notice.

Downloaded from www.Manualslib.com manuals search engine

 Connect the power cord into a grounded outlet.

OVERVIEW 3 Important Safety Instructions

CONNECTING WITH 13 Installation

LIVE 21 Getting Started

USING THE DVR 32 System Setup

BACKUP VIEWER 88 SEC Backup Viewer

DIGITAL VIDEO RECORDER

DVR Adapter / Power Cable Mouse

SEB-1005R (4EA) SEB-1007R (4EA)

User Manual CD,

DIGITAL VIDEO RECORDER

Part Names Functions

USB Port Connects the USB devices.

Power LED : Displays the power ON/OFF status.

ALARM IN ALARM OUT

Part Names Functions

CAMERA IN Video Signal input ports (UTP type connector).

b VIDEO OUT Video Signal Output Port (RCA jack).

Audio input signal port (RCA jack, CH1).

NETWORK NETWORK connector port.

DC 12V Camera and DVR power input port.

 USB USB connector port.

ALARM IN 1~4, G : Alarm Input port.

 VGA VGA Video Signal Output Port.

 AUDIO OUT Audio Signal Output Port (RCA jack).

FR, STOP, PLAY/PAUSE, FF

Using the Numeric buttons

 CONNECTING WITH OTHER DEVICE

CHECKING THE INSTALLATION ENVIRONMENT

Life (Unit: HOURS)

ALARM IN ALARM OUT

M  Only one mouse port is available.

CONNECTING THE USB

14_ connecting with other device

 CONNECTING WITH OTHER DEVICE

b IR LED These infrared LED's are controlled by the illumination sensor.

Illumination Sensor Detects incoming light to control the IR LED.

RJ-45 Cable (Length: 18.3m, 60ft)

<Cable pin information provided>

 You should be careful when installing the BOX

may be wet with moisture or pile up with impurities.

Camera Bracket Specification

Installation Wall or Ceiling

57(W) X 47.2(H) X 100.5(L) mm/ 40(W) X 58(H) X 40(D) mm/

Weight 130g(0.29 lbs) 55g (0.12 lbs)

Operating Temperature -10˚C ~ 50˚C (14˚F ~ 122˚F)

Accessories SCREW (M4 X L15) : 3 pcs

16_ connecting with other device

 CONNECTING WITH OTHER DEVICE

4. Loosen the handle by turning it counter clockwise

Connecting the alarm input signal IN

Connecting the alarm output signal

18_ connecting with other device

Connecting to Network through Ethernet (10/100BaseT)

USB USB connector port.

VGA VGA Video Signal Output Port.

AUDIO OUT Audio Signal Output Port (RCA jack).

Record/Stop Starts/stops the standard recording.

Play Refer to “Search & Play > Play”. (Page 65)

Search Refer to “Search & Play > Search”. (Page 62)

Alarm Stops the alarm if it's activated.

Freeze Freezes the Live screen temporarily.

Record Start/End recording the Live screen.

4. Use direction buttons (◄ ►) to select a desired date,

3. Use direction buttons (◄ ►) to move to a desired