Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Atcc Bacterial Culture Guide: Tips and Techniques For Culturing Bacteria and Bacteriophages

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

ATCC® Bacterial Culture Guide

tips and techniques for culturing bacteria and bacteriophages

The Essentials of
Life Science Research
Globally Delivered™


Table of Contents
This guide contains general technical information for bacterial growth, propagation, preservation, and
application. Additional information on bacterial culturing can be found in Bergey’s Manual of Systematic
Bacteriology, 2nd Edition, published by Springer, New York1.

Getting Started with an ATCC Bacterial Biosafety and Disposal.................................................. 25


Strain................................................................................................1 Biosafety..................................................................... 25
Product Sheet..............................................................1 Disposal of Infectious Materials......................... 25
Nomenclature Changes...........................................1
Preparation of Medium............................................1 Bacterial Authentication............................................. 26
Opening Glass Ampoules........................................1 Phenotypic Characterization ............................. 26
Initiating Frozen Cultures........................................2 Genotypic Characterization ............................... 26
Initiating Lyophilized Cultures..............................2
Bacterial Applications.................................................... 27
Bacterial Growth and Propagation.......................4 Quality Control......................................................... 27
Bacterial Growth Conditions..................................4 Consumable Products........................................... 27
Bacterial Propagation...............................................5 Probiotics................................................................... 27
Bacterial Titering...................................................... 10 Vitamins...................................................................... 27
Antibiotics.................................................................. 28
Growth Media....................................................................... 11 Organic Acids............................................................ 28
Bacterial Culture Media ........................................ 11 Biofuels....................................................................... 28
Microbial Media Formulations........................... 13
Media Ingredients................................................... 13 Glossary...................................................................................... 29
Media Supplements............................................... 14
References................................................................................ 31
Preservation........................................................................... 18
Cryopreservation..................................................... 18
Lyophilization .......................................................... 21
Preservation of Fastidious Bacteria................... 23
Special Hazards........................................................ 24

Phone 800.638.6597 www.atcc.org


Getting Started with an ATCC Bacterial Strain
Getting Started with an ATCC Bacterial Strain
ATCC bacterial strains are shipped either frozen on dry ice in plastic cryopreservation vials or as lyophilized
cultures in glass ampoules or serum vials. Upon receipt of frozen cultures, immediately revive cultures by
thawing and subsequently transferring cultures to an appropriate growth medium. If this is not possible,
store frozen vials in liquid nitrogen vapor (below -130°C). Alternatively, the frozen material can be stored
between -70°C and -80°C for short periods (1 to 5 days); however, viability will decline at temperatures
above -130°C. Freeze-dried cultures can be stored safely at 4°C or lower. Upon receipt, rehydrate or dilute
cultures using the appropriate medium and incubation conditions specified on the product sheet.

Product Sheet
ATCC bacterial strains are shipped with a product sheet that contains detailed information on the
rehydration and expansion of materials, as well as ideal growth and propagation conditions. This product
sheet, as well as additional information, can be found on the ATCC website or can be requested from the
ATCC Technical Service Department.

Nomenclature Changes
Changes in taxonomy or further analysis of bacterial strains may lead to a change in nomenclature. These
changes are indicated on product sheets and can be found online on the product page. Further information
on bacterial nomenclature changes can be found on the List of Prokaryotic Names with Standing in
Nomenclature (LPSN), which can be accessed online at http://www.bacterio.cict.fr/.

Preparation of Medium
In advance, prepare the appropriate medium and additional reagents necessary for bacterial strain revival
and growth. Ensure that the proper incubation conditions are ready. Information for the formulation and
preparation of the media and incubation conditions for these products is available on the ATCC website.

Opening Glass Ampoules


Overview
All cultures should be considered as potentially hazardous and should be opened by individuals trained
in microbiological techniques working in facilities with containment requirements appropriate for the
biosafety level of the cultures. ATCC recommends that the handling or opening of glass ampoules be
performed in a biological safety cabinet. If this is not possible, wear protective clothing, gloves, a face shield
or safety goggles, and hold the vial away from your body. Ensure that all empty vials are sterilized before
disposal.

page 1 www.atcc.org Email tech@atcc.org


Getting Started with an ATCC Bacterial Strain
Opening Double-Vial Preparations (see diagram on page 3)
1. Heat the tip of the outer vial in a flame.
2. Add a few drops of water on the hot tip to crack the glass.
3. Strike the end of the vial with a file or pencil to remove the tip.
4. Remove the insulation and inner vial with sterile forceps.
Gently raise the cotton plug.
Opening Single-Vial Preparations (see diagram on page 3)
1. To recover the cell suspension from the glass ampoule, score the neck of the ampoule with a small,
sterile file.
2. Disinfect the outside of the ampoule with freshly prepared 70% ethanol or dip it into a beaker of freshly
prepared 70% ethanol.
3. Wrap the ampoule within several folds of a sterile towel or gauze to dry residual ethanol.
4. Working in a laminar flow hood, hold the vial upright and snap open the vial. Ensure that your gauze
does not become too wet with ethanol, or alcohol could be sucked into the culture when the vacuum
is broken. Rehydrate the material immediately.

Initiating Frozen Cultures


1. Prepare a sterile test tube that contains the recommended medium for bacterial growth as listed in the
supplied product sheet. Ensure that the medium contains all necessary reagents and is equilibrated for
temperature and pH.
2. Thaw the sample vial via gentle agitation in a water bath that is set to the normal growth temperature
of that strain. Thawing will be rapid; approximately 2 minutes or until all ice crystals have melted.
3. Remove the vial from the water bath and decontaminate the outer surface using 70% ethanol. Follow
strict aseptic conditions in a laminar flow hood for all further manipulations.
4. Unscrew the top of the vial and transfer the entire contents to a sterile test tube containing the
appropriate growth medium. Additional test tubes can be inoculated by transferring 0.5 mL of the
primary culture to additional secondary cultures.
5. Incubate cultures under the appropriate temperature and atmospheric Note 1:
conditions as recommended on the product sheet. Following recover y from
6. Examine cultures after the recommended incubation period. The cryopreservation or lyophilization,
some bacterial strains may exhibit
incubation period will vary between strains and is listed on the product a prolonged lag phase. These
sheet. (See: NOTE 1) strains may require an extended
incubation period.
Initiating Lyophilized Cultures
1. Using a Pasteur pipette, aseptically add 0.5 mL of the recommended growth medium to the freeze-
dried material. Mix well.
2. Transfer the entire suspension to a test tube containing 5 to 6 mL of the recommended medium.
Additionally, transfer several drops of the suspension to an agar slant.
3. Incubate cultures under the appropriate temperature and atmospheric conditions as recommended
on the product sheet. Additional test tubes can be inoculated by transferring 0.5 mL of the primary
culture to additional secondary cultures.
4. Most freeze-dried cultures will grow within a few days. (See: NOTE 1)

Phone 800.638.6597 www.atcc.org page 2


Getting Started with an ATCC Bacterial Strain

Tip
Insulator
Cotton plug
Outer vial (soft glass) Borosilicate glass
Inner vial
Freeze-dried pellet Freeze-dried cells
Cotton
Desiccant with indicator

These preparations may be enclosed in a thin skin of


Heat the tip of the outer cellulose; this skin must be removed (either with a sharp
vial in a flame blade or by soaking in water for a few minutes). Score the
ampule once briskly with a sharp file about one inch
from the tip.

Squirt a few drops of water


on the hot tip to crack glass

Disinfect the ampule with alcohol-dampened gauze

Strike with file or


pencil to remove tip

Wrap gauze around the ampule, and break at the scored area.
Care should be taken not to have the gauze too wet, or
alcohol could be sucked into the culture when the vacuum is
broken. Rehydrate material at once.

Remove insulation and inner vial with


forceps, gently raise cotton plug

page 3 www.atcc.org Email tech@atcc.org


Bacterial Growth and Propagation
Bacterial Growth and Propagation
Bacterial Growth Conditions
Temperature
Because bacteria can grow and thrive in a variety of environments, optimal growth temperatures may
vary significantly between species. In general, most pathogenic or commensal bacterial strains grow well
at body temperature (37°C). In contrast, many environmental strains thrive at lower temperatures, often
within a range of 25°C to 30°C.
Bacterial species can be categorized based on their growth temperature;
Note 2:
these include psychrophiles (0°C to 20°C), mesophiles (25°C to 40°C), and Regularly calibrate the temperature
thermophiles (45°C to 122°C). Though bacterial strains require optimal control system of incubators. Use
temperatures for growth and reproduction, most strains can withstand an alarm system when possible to
warn against temperature increases
considerable drops in temperature and survive several days at 4°C. At these above the optimum setting.
lower temperatures, bacterial growth and metabolism are significantly
diminished. (See: NOTE 2)
Atmosphere
In addition to varying requirements for optimal growth
temperatures, bacteria also differ in their use of oxygen for
respiration. Aerobic organisms, such as Bacillus species, use
oxygen as a terminal electron acceptor during respiration.
Similarly, microaerophiles, such as Helicobacter pylori, also
require the use of oxygen, but at lower levels than naturally
occurring in the environment. In contrast, anaerobic organisms
use electron acceptors such as nitrate or sulfate, among other
inorganic acceptors. These inorganic compounds, however, have
a lower reduction potential than oxygen thus resulting in less
efficient respiration.
The use of oxygen and inorganic compounds by anaerobic organisms can differ greatly between species.
Obligate anaerobes, such as Clostridium species, can only survive and reproduce in the absence of
oxygen; these organisms are often killed by the presence of oxygen. Similarly, aerotolerant anaerobes,
such as Lactobacillus species, cannot use oxygen during respiration; however, unlike strict anaerobes,
these microorganisms can tolerate oxygen for short periods of time. Lastly, facultative anaerobes, such as
Escherichia coli and Staphylococcus species, are able to survive in both the presence and absence of oxygen.
If given the choice, these organisms prefer the use of oxygen during respiration as it has the greatest
reduction potential as compared to other electron acceptors.
When working with anaerobic cultures, it is important to avoid unnecessary exposure to oxygen. Anaerobic
conditions may be obtained for either transfer or incubation by the methods listed below. Unless specifically
mentioned, the standard anaerobic gas mixture is 80% N2, 10% CO2, and 10% H2.
Anaerobic conditions for transfer may be obtained by either of the following:
1. Use of an anaerobic gas chamber.
2. Placement of test tubes under a gassing cannula system hooked to anaerobic gas.

Phone 800.638.6597 www.atcc.org page 4

You might also like