ht-r695 Bas Adv Manual en

> Before start > Hookup > Setup > Playback > Part Names > Advanced Manual
Troubleshooting | Appendix
Basic Manual Hookup

Step1: Conect the Speakers ....................................................3
Step2: Connect the TV ............................................................5
Step3: Connect the AV Components .......................................7
Step4: Multi-zone Connection ...............................................10
Step5: Connect Other Cables ................................................11
Setup
Step6: Power On & Initial Setup ............................................12
HDMI Setup ...........................................................................13
Playback
Basic Playback ......................................................................14
Network Functions .................................................................15
Others ....................................................................................17
Part Names
Front Panel ............................................................................19
Rear Panel ............................................................................20
Remote Controller .................................................................21
Display ...................................................................................21
The Basic Manual includes information needed when starting up and

also instructions for frequently used operations. The Advanced Manual
has more detailed information and advanced settings.
AV RECEIVER
HT-R695
What's in the box

1. Main unit 2. Remote controller (RC-911R) ×1, Batteries (AAA/R03) ×2
3. Indoor FM antenna ×1 4. AM loop antenna ×1 5. Speaker setup microphone ×1
Main features
This unit is connected between your TV and your AV components. To play, select the source with the input
selector. This unit is equipped with 7ch at 170 W (6 ohms, 1 kHz, 0.9%THD) (North American models) / 160 W
(6 ohms, 1 kHz, 1%THD) (Australian and Asian models) per channel plus pre out jack for powered subwoofer.
$ Supports playback in Dolby Atmos format which provides 360e sound placement
$ The HDMI jack supports 4K video input and output. Jacks IN1 to 3 and OUT MAIN/SUB support HDCP2.2
$ HDMI CEC functionality: Control features such as linking input switching with the input selector and players
conforming to the CEC standard, switching audio output and volume using the remote controller of a CEC-
compliant TV, and automatically switching this unit to standby when the TV is turned off
$ HDMI Standby Through: Video and audio signals from AV components can be transmitted to the TV even if this
unit is in standby
$ ARC: Connection with an ARC-compatible TV is complete with one HDMI cable
$ Easy Initial Setup using onscreen guidance and On-Screen Display (OSD) showing operations on the TV
$ Internet radio and AirPlay via wired LAN or Wi-Fi (wireless LAN) and network features such as Music Server
that enables PC music file playback, USB playback, plus other playback features such as AM/FM radio and
1 BLUETOOTH® play
$ Playback formats supported by Music Server and USB include WAV, FLAC and DSD high-res source
$ Multi-zone Connection which allows you to play in the main room and listen in a separate room (ZONE 2)
$ We plan to provide support for the DTS:X audio format through a firmware update for this unit. Refer to our
website for more information.
CAUTION: Connect speakers with 6 Ω to 16 Ω impedance. The power cord must be connected only after
all other cable connections are completed.
2 3 4 0 We will not accept responsibility for damage arising from the connection of equipment manufactured by
other companies.
Before start
5
2
Step1: Conect the Speakers

Speaker Layout for 5.1.2-
Channel System
Dolby enabled speakers (front) are front speakers with
height speakers on top, designed to face the ceiling so
that height speaker sound is heard after bouncing off the
ceiling so that sound appears to be coming from
overhead. You can experience the Dolby Atmos listening
mode (5.1.2 channel playback), which realizes the most
up-to-date 3D sound including overhead sounds, when
the input audio format is Dolby Atmos.
Dolby enabled speakers (front) speakers should be set up
at ear height and the center speaker should be set up
facing the listening position. The optimal positioning for
surround speakers is just above ear height. Place the
powered subwoofer towards the front. Placing it between
the center speaker and a front speaker gives you a
natural sound even when playing music.
0 The front speakers, center speaker, and surround
speakers are counted as 5 channels, the powered
subwoofer is counted as 0.1 of a channel, and the
height speakers are counted as 0.0.2 of a channel,
giving us a 5.1.2ch system.
1 2 Dolby Enabled Speakers (Front) ＊1
3 Center Speaker ＊2
4 5 Surround Speakers
6 Powered Subwoofer
＊ 1: 22e to 30e, ＊ 2: 120e
Hookup
3
Connections for 5.1.2-

Channel System
Connect 123456. 2 speaker cables are required to
connect each of speakers 1 and 2. Use one speaker
cable for the other speakers' connection. Up to two
powered subwoofers can be connected. The same signal
is output from each of the SUBWOOFER jacks.
1/2˝
(12 mm)
1
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
1 Speaker cable, 2 Subwoofer cable

4
Step2: Connect the TV

if you have:
ARC TV
This unit is connected between your TV and AV
components. If you connect two or more AV components,
you can select the video displayed on the TV and the
audio output from this unit by changing the input selector.
Shown here are the connections for a TV that supports
the ARC (Audio Return Channel) feature. By connecting
with a single HDMI cable, you can not only output the
video input to this unit to the TV, but you can also play the
sound from the TV through this unit.
Choose an HDMI IN jack on the TV that supports ARC
when connecting.
Setup
0 Settings are required to use the ARC function.
Select "Yes" in "5. Audio Return Channel" (P13)
in the Initial Setup.
0 Please refer to the TV's operation manual for
directions on connections and setup for the TV.
1
HDMI IN (ARC)
Another TV or projector can be connected to the HDMI OUT SUB
jack. This jack does not support ARC. For details about how to
output video from the HDMI OUT SUB jack (P14)
TV
1 HDMI cable
5
if you have:
Non-ARC TV
This unit is connected between your TV and AV
components. If you connect two or more AV components,
you can select the video displayed on the TV and the
audio output from this unit by changing the input selector.
This describes the connections for a TV that does not
support the ARC (Audio Return Channel) feature. By
connecting with both an HDMI cable and a digital optical
cable, you can not only output the video input to this unit
to the TV, but you can also play the sound from the TV
through this unit.
If the TV doesn't have a DIGITAL OPTICAL OUT jack, use
an analog audio cable and connect the TV's ANALOG
AUDIO OUT jack to the AUDIO IN TV jack on this unit.
0 Connection with a digital optical cable is not necessary
if you will watch TV through a device such as a cable
set-top box (that is, not use a tuner built into the TV)
that you have connected to the INPUT jack on this unit.
Another TV or projector can be connected to the HDMI OUT SUB

jack. This jack does not support ARC. For details about how to
2 1 output video from the HDMI OUT SUB jack (P14)
TV
1 HDMI cable, 2 Digital optical cable
6
Step3: Connect the AV Components

if you have:
HDMI AV Components
This is an example of connection with an AV component
that has an HDMI jack. With connection to an AV
component that conforms with the CEC (Consumer
Electronics Control) standard, you can use features such
as the HDMI CEC feature that links with the input selector,
and the HDMI Standby Through feature which allows you
to play video and audio from AV components on the TV
even when this unit is in standby mode.
0 To play 4K or 1080p video, use a high speed HDMI
cable. Further, to enjoy HDCP2.2 compatible video,
connect to the HDMI IN1 to IN3 jacks.
Setup
0 HDMI setup (P13) is required to use the HDMI
CEC and HDMI Standby Through features. Make
settings after all connections are complete.
0 To enjoy digital surround sound including Dolby
Digital, audio output should be set to "Bitstream
output" on the connected Blu-ray Disc player or
other device.
You can connect a device such as a video camera to the AUX

INPUT HDMI jack on the front panel.
BD/DVD
Cable/Satellite set-top Streaming media

GAME
box player
1 HDMI cable
7
if you have:
Non-HDMI AV Components
This is an example of connection with an AV component
that does not have an HDMI jack. Make the connections
to the AV component to match the jacks it has. When
video input connection is to the BD/DVD jack, the audio
input connection should also be to the BD/DVD jacks, and
so on, so that you connect the video input jacks to the
jacks with the same name as the audio input jacks. Note
that video signals input to the VIDEO IN jack or the
COMPONENT VIDEO IN jacks will be converted to HDMI
video signals and then output from the HDMI OUT jack.
0 To enjoy digital surround playback in formats such as
Dolby Digital, you need to make a connection for audio
signals with a digital coaxial cable or digital optical
cable.
0 It is possible to change assignment of the input jacks
you see in the illustration at left, so you can also
connect to any jack other than BD/DVD. For details,
see the Advanced Manual.
Setup
0 The COMPONENT VIDEO IN jacks are
compatible only with 480i or 576i resolution. When
you input video signals to the COMPONENT
VIDEO IN jacks, set the output resolution of the
player to 480i or 576i. Select interlace if there is no
1 option for 480i, etc. If your player does not support
2 OR 3 480i or 576i output, use the VIDEO IN jack.
0 To enjoy digital surround sound including Dolby
Digital, audio output should be set to "Bitstream
output" on the connected Blu-ray Disc Player or
other device.
BD/DVD
1 Component video cable, 2 Digital coaxial cable, 3 Analog audio cable

8
if you have:
Audio Components
Example of a connection with an audio component.
Connect a CD player using a digital optical cable or
analog audio cable. You can also connect a turntable that
has an MM-type cartridge to the PHONO jack.
0 If the turntable has a built-in audio equalizer, connect it
to an AUDIO IN jack other than the PHONO jack.
Further, if the turntable uses an MC type cartridge,
install an audio equalizer compatible with the MC type
cartridge between the unit and the turntable, then
connect to any AUDIO IN jack other than the PHONO
jack.
If the turntable has a ground wire, connect it to the GND terminal

of this unit.
OR 1
2
Turntable CD
1 Digital optical cable, 2 Analog audio cable

9
Step4: Multi-zone Connection

ZONE 2 LINE OUT /
ZONE SPEAKER
You can enjoy audio in the separate room by, for example,
playing a Blu-ray Disc player in the main room (where this
unit is located) and listening to internet radio in the
separate room (ZONE 2).
Connections with an AV component

When outputting the audio of an external AV component
to ZONE 2, you need to connect using an analog audio
cable or digital optical cable, or digital coaxial cable.
ZONE 2 LINE OUT

It is possible to play 2 ch source in a separate room while
5.1.2 ch source is being played in the main room.
Connect the ZONE 2 LINE OUT jacks of the unit and the
MAIN ROOM LINE IN jacks of the pre-main amplifier in a separate room
with an analog audio cable.
ZONE2 ZONE SPEAKER

It is possible to connect speakers in a separate room and
play 2 ch sources.
0 During ZONE 2 playback, no sound is heard from the
3 height speakers and a maximum of 5.1 channel
playback is possible in the main room. Listening modes
2 such as the Dolby Atmos modes cannot be selected.
Setup
1 LINE 0 Settings are required in Initial Setup, "4. Multi
IN Zone Setup" (P13) to enjoy this feature.
0 The audio from externally connected AV
OR components can only be played in ZONE 2 when
ZONE SPEAKER the audio is analog or 2ch PCM audio. If you have
connected to this unit with a digital coaxial cable or
BD/DVD digital optical cable, may be necessary to convert
ZONE2 LINE OUT the audio output of the AV component to PCM
output.
1 Digital coaxial cable, 2 Analog audio cable, 3 Speaker cable

10
Step5: Connect Other Cables

Antenna Hookup Network Hookup
Move the antenna around while playing the radio to find Connect this unit to the network using wired LAN or Wi-Fi
the position with the best reception. Use a thumb tack or (wireless LAN). You can enjoy network features such as
similar to attach the indoor FM antenna to a wall. internet radio, Music Server, and AirPlay by connecting the
AM unit to the network.
If you connect by wired LAN, connect with an Ethernet
FM cable to the ETHERNET port as shown in the illustration.
To connect by Wi-Fi, then after selecting "Wireless" in "3.
Network Connection" (P13) in Initial Setup, select the
AM loop antenna desired setting method and follow the onscreen
instructions to configure the connection.
Indoor FM antenna
(North American models)
Power Cord Hookup
Connect the power cord to the power outlet after

completing all other connections.
(Australian and Asian models)
11
Step6: Power On & Initial Setup

Initial Setup starts automatically 1. AccuEQ Room Calibration
Once all connections are complete, change the TV's input
to the input for this unit, inset batteries in the remote Place the supplied speaker setup microphone in the
controller, and press Í to turn the power on. When you listening position, measure the test tones emitted by the
turn the unit on for the first time, Initial Setup is speakers, then the unit automatically sets the optimum
automatically shown on the TV to enable you to make volume level for each speaker, the crossover frequencies,
settings required for startup using simple operations and the distance from the listening position. This also
following onscreen guidance. enables correction of distortion caused by the acoustic
These instructions will guide you through some items that environment of the room.
you need to check beforehand. Read beforehand so the
setup goes smoothly.
Initial Setup
Language Select
English
Deutsch
Français
Español
Italiano
Nederlands SETUP MIC
Svenska
Exit
a Operation
Select the item with the cursors of the remote controller
b and press ENTER (a). To return to the previous screen, 0 When putting the speaker setup microphone on a tripod,
press (b). refer to the illustration when putting it in place.
0 The subwoofer sound may not be detected since it is
To redo the Initial Setup extremely low frequencies. Set the subwoofer volume to
If you terminate the procedure on the way or want to more than halfway.
change a setting made during Initial Setup, press on 0 Calibration takes several minutes to be completed. The
the remote controller, select "7. Miscellaneous" – "Initial speakers emit the test tone at high volume during
Setup", and press ENTER. measurement, so be careful of your surroundings. Keep
the room as quiet as possible during measurement. If
the measurement is interrupted, turn off the household
appliances.
Setup
12
HDMI Setup
2. Source Connection To switch between upper and lower case, select "A/a" on HDMI CEC
the screen and press ENTER. To select whether to mask Make this setting to enable the control feature for devices
Check that each input source is connected correctly. Follow the password with " ＊ " or display it in plain text, press complying with the CEC standard. This is set to on
the guidance, select the input you want to confirm, start MEMORY on the remote controller. Press CLEAR to delete automatically if you have selected "Yes" in "5. Audio Return
play of the selected player, and confirm that the images all the input characters. Channel" in the Initial Setup.
appear on the TV and that sound is played. Press the button on the remote controller to set "5.
0 A confirmation screen asking you to agree to the privacy Hardware" – "HDMI" – "HDMI CEC" to "On" on the TV
policy is displayed during network setting. Select "Yes" screen. Also enable the CEC control feature on the CEC
and press ENTER to indicate agreement. device you have connected.
3. Network Connection
Set up Wi-Fi connection with an access point such as a 4. Multi Zone Setup
5-1 HDMI
wireless LAN router. There are the following two methods of HDMI CEC On
connecting by Wi-Fi: HDMI Standby Through Auto(Eco)
"Scan Networks": Search for an access point from this When you want to enjoy audio in a room other than the Audio TV Out Auto
unit. Find out the SSID of the access point beforehand. main room, set the audio output method for the separate Audio Return Channel Auto
"Use iOS Device (iOS7 or later)": Share the iOS device's room (ZONE 2). If you have connected speakers in a Auto Lip Sync On
Wi-Fi settings with this unit. separate room with speaker cable, select "Using AV
Receiver". If you have connected a pre-main amplifier in a
If you select "Scan Networks", there are a further two separate room with an analog audio cable, select "with
choices of connection method. Check the following. External Premain Amplifier". HDMI Standby Through
0 "Enter Password": Enter the password (or key) of the Even if this unit is in standby, the input signals from AV
access point to connect. components are transmitted to the TV.
0 "Push Button": If the access point has an automatic 5. Audio Return Channel 0 "Auto" / "Auto (Eco)": Select one of these settings
connection button, you can connect without entering a when connected AV components comply with the CEC
password. If you have connected a TV that supports ARC, select standard. Irrespective of the input selector selected
0 If the SSID of the access point is not displayed, then in "Yes". This unit's ARC setting turns on and you can listen to immediately before switching the unit to standby, you can
the screen listing the SSIDs, select "Other..." with the  the TV's audio through this unit. transmit the input signals from AV components to the TV.
cursor on the remote controller and press ENTER, then 0 If you select "Yes", the HDMI CEC function is enabled Select "Auto (Eco)" if the TV is also CEC-compliant. You
follow the onscreen instructions. and power consumption increases during standby. can reduce power consumption in standby mode.
0 Input selector names for "BD/DVD", etc.: You can
Keyboard input transmit the input signals from the set input selector to
the TV. It can be selected when "HDMI CEC" is set to
"Off".
Wi-Fi Setup
SSID
0 "Last": You can transfer the input signals of the input
selector selected immediately prior to the unit being
a b c d e f g h i j k l m switched to standby. It can be selected when "HDMI
n o p q r s t u v w x y z
CEC" is set to "Off". With this setting, you can switch the
1 2 3 4 5 6 7 8 9 0 - ^ \
, . / ; : @ [ ] input selector even in the standby mode.
A/a Ɵ ơ OK To exit the settings, press .
When finished, select the "OK" key.
All Erase A/a
13
Basic Playback
AV Component Playback Digital and DTS-HD Master Audio is displayed for that content is selected automatically.
for DTS-HD Master Audio. The output is Stereo Press (d) repeatedly to switch the display of
a 1. Switch the input on the TV to that assigned to for 2-channel input signals. the main unit in order of:
the unit. Input source & volume
2. Press the input selector (a) on the remote Direct
d This listening mode can be selected for all input
controller with the same name as the jack to
which you connected the player to switch the signals. It shuts down processing that affects
input. sound quality to deliver a playback sound quality
For example, press BD/DVD to play the closer to sources. Speakers play the sound field
Listening mode
player connected to the BD/DVD jack. Press according to the number of channels in the input
TV to listen the TV's sound. signal, so there would be output from only the
0 When the CEC link function works, the front speakers for a 2 ch signal, for example.
input switches automatically when you
have connected a CEC compliant TV and Dolby Surround/DTS Neural:X Signal format
player to this unit using HDMI connection. These listening modes allow you to expand the
3. Start play on the player. playback signal to 5.1 channels or 7.1 channels
4. Use VOL+/– (b) to adjust the volume. to suit the connected speaker configuration
b when the input signal is 2 channels or The display changes few
5.1 channels. seconds later.
When a TV is connected to the HDMI OUT
c SUB jack 0 We plan to provide support for the DTS Sampling frequency
Press Q on the remote controller to display the Neural:X a firmware update for this unit. You
Quick Menu, and set "Other" – "HDMI Out" to can select Neo:6 Cinema and Neo:6 Music
either "SUB" or "MAIN+SUB". until the update.
Original surround modes Input signal resolution

You can select listening modes such as the All
Listening Mode
Ch Stereo mode where a stereo image is played
from both the front and the rear, and Orchestra
This unit is equipped with a variety of listening (only with the MUSIC button) which is best for
modes, and you can select the optimum playback of classical and opera pieces.
listening mode for movies, TV, music, and
games by repeatedly pressing the MOVIE/TV, Pure Audio (Australian and Asian models)
MUSIC, and GAME buttons (c). For details on Listening mode that provides purer sound Playback
the listening modes, see the Advanced Manual. quality by switching off the power of the display
This section introduces some of the popular and analog video circuits.
modes.
The listening mode last selected for the source
Dolby Digital/DTS modes is remembered for each of the MOVIE/TV,
When the input signal is a digital surround MUSIC, and GAME buttons. If content you play
format such as Dolby Digital or DTS, you can is not supported by the listening mode you
select the listening mode that suits the input selected last, the listening mode that is standard
signal. Dolby Digital is displayed for Dolby
14
Network Functions
Network Services Player 11 or 12 network servers or NAS that
are compatible with home network
1. Switch the input on the TV to that assigned to functionality. You may need to make some
the unit. settings in advance to use Windows Media®
2. Press NET to display the network service list Player 11 or 12. Enable media streaming for
screen. this player in Windows Media® Player. For
details, see the Advanced Manual.
USB
Play music files on a USB storage device.
Connect the USB storage device to the USB
jack on the rear of the unit, select USB in the list
of network services, and press ENTER to
a confirm. Select the desired folder or music file
with the cursors, and press ENTER to confirm
b and start playback.
0 Operation cannot be guaranteed for all USB
3. Select the item with the cursors of the remote storage devices.
controller and press ENTER to confirm your 0 This unit can use USB storage devices that
selection (a). To return to the previous comply with the USB mass storage device
screen, press (b). class standard. The unit is also compatible
with USB storage devices using the FAT16 or
Internet Radio FAT32 file system formats.
When this unit is connected to a network, you
can listen to TuneIn or other preregistered Notes:
Internet radio services. After selecting the 0 Network services become selectable after the
desired service, follow the on-screen network starts up even if they cannot be
selected first.
instructions, using the cursors to select radio 0 Functionality may be introduced by firmware
stations and programs, then press ENTER to updates and service providers may cease
play. Play starts when 100% is displayed for services, meaning that some network services
buffering. and content may become unavailable in the
future. Furthermore, available services may
vary depending on your area of residence.
Music Server
You can play music files stored on home-
network compliant PCs or NAS devices
connected to the same network as this unit.
Select the server with the cursors, select the
desired music file and press ENTER to start
playback. Play starts when 100% is displayed
for buffering.
0 This unit is compatible with Windows Media®
15
AirPlay BLUETOOTH® Playback
You can wirelessly enjoy the music files on an iPhone®, Pairing

iPod touch®, or iPad® connected to the same access point 1. When you press the button on the remote controller,
as this unit. "Now Pairing..." is displayed on this unit's display, and
0 Update the OS version on your iOS device to the latest the pairing mode is enabled.
version.
1. Connect the iOS device to the access point.
2. Press NET.
3. Tap the AirPlay icon in the control center of the iOS
device and select this unit from the list of devices 2. Enable (turn on) the BLUETOOTH function of the
displayed, and tap "Done". BLUETOOTH enabled device, then select this unit from
4. Play the music files on the iOS device. amongst the devices displayed.
0 The default status is for the Network Standby feature to If a password is requested, enter "0000".
be on, so when you do steps 3 and 4 above, this unit 0 To connect another BLUETOOTH enabled device, press
automatically comes on and input switches to "NET". To and hold the button until "Now Pairing..." is
reduce the amount of power consumed in standby displayed, then perform step 2 above. This unit can
mode, press the button on the remote controller, store the data of up to 8 paired devices.
Onkyo HT-RXX
then in the Setup menu displayed set "5. Hardware" – 0 The coverage area is 48 feet (15 meters). Note that
"Power Management" – "Network Standby" to "Off". connection is not always guaranteed with all
0 Due to the characteristics of AirPlay wireless BLUETOOTH enabled devices.
technology, the sound produced on this unit may slightly
be behind the sound played on the AirPlay-enabled Playing Back
device. 1. When the unit is on, connect the BLUETOOTH enabled
iPhone device.
Onkyo HT-RXX You can also play back music files on the computer with 2. The input selector of this unit will be automatically
iTunes (Ver. 10.2 or later). Before operation, make sure switched to "BLUETOOTH".
this unit and the PC are connected to the same network, 3. Play music. Increase the volume of the BLUETOOTH
then press NET on this unit. Next, click the AirPlay icon enabled device to an appropriate level.
in iTunes, select this unit from the list of devices displayed, 0 Due to the characteristics of BLUETOOTH wireless
and start play of a music file. technology, the sound produced on this unit may slightly
be behind the sound played on the BLUETOOTH
enabled device.
16
Others
Listening To the Radio Multi-zone
d
a 1. Press TUNER (a) on the remote controller repeatedly to Settings are required if you have connected the speakers
select either "AM" or "FM" on the display. e in the separate room (ZONE 2) using speaker cables. If
2. Press MODE (c) on the remote controller, so that the you haven't made the "4. Multi Zone Setup" (P13)
b "TunMode: Auto" is displayed on the display. settings in Initial Setup, press the button on the remote
3. When you press the  /  cursor (b) buttons on the controller and set "2. Speaker" – "Configuration" – "Zone
remote controller, automatic tuning starts, and searching Speaker" to "Zone 2".
stops when a station is found. When tuned into a radio
station, the "TUNED" indicator on the display lights. Play
1. While holding down MODE (a) on the remote controller,
You can preset up to 40 stations. press ZONE 2 (b) for 3 or more seconds until the remote
1. Tune into the AM/FM radio station you want to register. indicator blinks twice.
2. Press MEMORY (d) on the remote controller so that the 0 The remote controller switches to the mode for
preset number on the display flashes. b controlling ZONE 2.
3. While the preset number is flashing (about 8 seconds),
c repeatedly press the  /  cursor (b) buttons on the c To return the remote controller to main room control
d remote controller to select a number between 1 and 40. mode: While holding down MODE (a) on the remote
4. Press MEMORY (d) again on the remote controller to a controller, press MAIN (c) for 3 seconds or more until the
e register the station. When registered, the preset number remote indicator flashes once.
stops flashing. To select a preset radio station, press the
 /  cursor (b) buttons on the remote controller. 2. Point the remote controller at the main unit and press Í
0 To delete a preset station, press the  /  cursor (b) (d).
buttons on the remote controller to select the preset "Z2" lights on the main unit display.
number you want to delete, press MEMORY (d) on the
remote controller and then press CLEAR (e) while the
preset number is flashing. When deleted, the number on
the display goes off.
3. Press the input selector button (e) of the input to be
Frequency step setting played in the separate room. To control on the main unit,
Press the button on the remote controller to select "7. press ZONE 2 and within 8 seconds, press the input
Miscellaneous" – "Tuner" – "AM/FM Frequency Step" or selector button of the input to be played in a separate
"AM Frequency Step" and select the frequency step for room. To play the same source in the main room and
your area. Note that when this setting is changed, all radio separate room, press ZONE 2 on the main unit twice.
presets are deleted. 0 You cannot select different inputs for the main room
and separate room with the "NET" or "BLUETOOTH"
input selector. You cannot select different stations for
the main room and separate room with the AM/FM
radio. When you select an input or station for the
separate room, the main room also switches.
0 DSD and Dolby TrueHD audio signals are not output
17
to ZONE 2 when selected with the "NET" input Others When the unit is operating erratically
selector.
4. Volume adjustment is done on the pre-main amplifier for To adjust the sound quality Try restarting the unit
the separate room when connected via ZONE 2 LINE
It is possible to enhance or moderate the bass and treble of Restarting the unit may help it operate more smoothly. To
OUT. When outputting from ZONE speakers, adjust with
front speakers. Press TONE on the main unit several times restart the unit, turn it to standby, and then press Í ON/
VOL+/– on the remote controller. To control on the main
to select the desired setting from "Bass" and "Treble", and STANDBY on the main unit for at least 5 seconds. (The
unit, press ZONE 2 and adjust with the MASTER
turn the TONE dial to adjust. unit’s settings will be maintained.) If there is no
VOLUME control within 8 seconds.
0 This cannot be set if the listening mode is Pure Audio improvement even after the unit is restarted, try
0 If ZONE 2 is on, power consumption during standby
(Australian and Asian models) or Direct. disconnecting and reconnecting the power cords of the unit
becomes larger than normal.
and connected equipment.
0 If ZONE 2 is turned on when the listening mode of the
Quick Menu
main room is Pure Audio, it will automatically switch to
By pressing Q on the remote controller during play, you can Resetting the unit (this resets the unit settings to the
the Direct listening mode. (Australian and Asian models)
adjust frequently used settings, such as the sound quality, default)
using on-screen menus. Select the item with the cursors of If restarting the unit doesn't fix the problem, resetting the
To turn off the function
the remote controller and press ENTER to confirm your unit to the status at the time of shipment may solve the
Press Í while in the mode for controlling ZONE 2 on the problem. If you reset the unit status, your preferences will
selection. To return to the previous screen, press .
remote controller. be reset to the defaults. Note them down before the
operation below.
Playing in ZONE 2 only Quick Menu BD/DVD
If you turn the unit to standby during multi-zone playback, Tone Bass
1. While pressing the CBL/SAT input selector button on the
the Z2 indicator is dimmed and the playback mode is Level Treble
main unit, press Í ON/STANDBY.
switched to playback in a separate room only. Setting AccuEQ
2. "Clear" appears on the display and the unit returns to
ZONE 2 to on while this unit is in standby will also switch Other
standby. Do not unplug the power cord until "Clear"
the playback mode to the same setting. disappears from the display.
0 You can adjust the sound quality with "Tone". "Other" To reset the remote controller, while holding down MODE,
includes settings such as "A/V Sync" that allows you to press until the remote indicator flash twice (about
3 seconds).
adjust the audio delay when the video is behind the
audio, "Music Optimizer" that provides better sound
quality for compressed audio, and "HDMI Out" which
allows you to select the HDMI OUT terminal to output
from "MAIN", "SUB", and "MAIN+SUB".
18
Front Panel
1 2 3 4 5 6 7 8 9 10 11 12
Part Names
13 14 15 16 17 18 19
1. Í ON/STANDBY button: Turns the unit on or into display in three steps. It cannot be turned off completely. change the mode. (P14)
standby mode. 8. Display (P21) 14.(Up) TONE button / (Down) TONE dial: Adjusts the high
2. MUSIC OPTIMIZER button/indicator (North American 9. SETUP button: Displays the Setup menu. tone and low tone. Press the button repeatedly to select
models): Turns on/off the Music Optimizer function that 10.Cursor buttons (4 TUNING 3 / 2 PRESET 1 button) the item to adjust from "Bass" and "Treble", and turn the
provides better sound quality for compressed audio. and ENTER button: Select the item with the cursors and dial to adjust.
PURE AUDIO button/indicator (Australian and Asian press ENTER to confirm your selection. When using the 15.PHONES jack: Stereo headphones with a standard plug
models): Switches the unit to Pure Audio mode. (P14) TUNER, select the frequency with 4 TUNING 3, or (1/4 inch or ø6.3 mm) are connected.
3. HYBRID STANDBY indicator: Lights if the unit enters select preset stations with 2 PRESET 1. 16.Input selector buttons: Switch the input to be played.
standby mode when the features are enabled that 11. RETURN button: Returns the display to the previous 17.SETUP MIC jack: The supplied speaker setup
continue to work when this unit is in standby, such as state. microphone is connected.
HDMI Standby Through and Network Standby. 12.MASTER VOLUME: Allows you to adjust the volume. 18.AUX INPUT AUDIO jack: You can play the audio from an
4. Remote control sensor 13.(Up) LISTENING MODE button / (Down) LISTENING external player by connecting using a stereo mini plug
5. ZONE 2 button: Controls the multi-zone function. (P17) MODE dial: Allows you to select the listening mode. cable.
6. OFF button: Switches the multi-zone function off. Press the button repeatedly to select a category from 19.AUX INPUT HDMI jack: Connect to a video camera, etc.,
7. DIMMER button: You can adjust the brightness of the "Movie/TV", "Music", "Game", then turn the dial to using a HDMI cable.
19
Rear Panel
1 2 3 4 5 6 7 8 9 10
9
90°
180°
11 12 13 14 15
1. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV 7. HDMI OUT jacks: Transmit video signals and audio the main room and the speakers for a separate room
component digital audio signals with a digital optical signals with a HDMI cable connected to a monitor such (ZONE 2). (North American models are compatible with
cable or digital coaxial cable. as a TV or projector. banana plugs.)
2. TUNER AM/FM 75Ω terminal: The supplied antennas 8. HDMI IN jacks: Transmit video signals and audio signals 14.ZONE 2 LINE OUT jack: Output audio signals with an
are connected. with a HDMI cable connected to an AV component. analog audio cable to a pre-main amplifier in a separate
3. VIDEO IN jacks: Input the video signals from AV 9. Wireless antenna: Used for Wi-Fi connection or when room (ZONE 2). (P10)
component with an analog video cable. using a BLUETOOTH enabled device. Adjust their 15.SUBWOOFER PRE OUT jack: Connect a powered
4. USB port: A USB storage device is connected so that angles according to the connection status. subwoofer with a subwoofer cable. Up to two powered
music files stored in it can be played. You can also 10.Power cord subwoofers can be connected. The same signal is output
supply power (maximum 5V/1A) to USB devices with a 11. GND terminal: The ground wire of the turntable is from each of the SUBWOOFER PRE OUT jacks.
USB cable. connected.
5. ETHERNET port: Connect to the network with an 12.AUDIO IN jacks: Input TV or AV component audio
Ethernet cable. signals with an analog audio cable.
6. COMPONENT VIDEO IN jacks: Input the video signals 13.SPEAKERS terminals: Connect speakers with speaker
from AV component with a component video cable. cables. You can connect the multichannel speakers for
20
Remote Controller Display

1. Í button: Turns the unit on or into standby mode. 1 2 3 4 5
2. Input selector buttons: Switches the input to be played.
3. Q (QUICK MENU) button: You can perform common settings on
the TV screen. (P18)
4. Cursor buttons and ENTER button: Select the item with the
1
cursors and press ENTER to confirm your selection.
5. button: Displays the Setup menu. 7 6 7
6. Volume buttons: Allows you to adjust the volume. This button
also cancels the muting. 1. Speaker/Channel display: Displays the output channel that
2 7. button: Temporarily mutes audio. Press again to cancel corresponds to the selected listening mode.
muting. 2. Lights in the following conditions.
8. LISTENING MODE buttons: Allows you to select the listening Ë: When headphones are connected.
mode. (P14) Z2: When ZONE 2 is on.
MAIN/ZONE 2 buttons: Controls the multi-zone function. (P17) : When connected by BLUETOOTH.
3 11 9. Play buttons: You can start play of the Music Server or USB. : When connected by Wi-Fi.
10. button: You can start repeat or random play of the Music NET: When "NET" is selected with the input selector and the unit is
Server or USB. connected to the network. It will flash if the connection to the network
4 CLEAR button: Deletes all characters you have entered when is not correct.
entering text on the TV screen. USB: When "NET" is selected with the input selector and the unit is
11. button: Switches the information on the display. connected by USB and the USB device is selected. Flashes if the
12. button: Returns the display to the previous state. USB is not properly connected.
5 12 13.MODE button: Switches tuning to an AM/FM station between HDMI: When HDMI signals are input and the HDMI input is selected.
automatic tuning and manual tuning. DIGITAL: When digital signals are input and the digital input is
14.MEMORY button: Used to register AM/FM radio stations. selected.
3. Lights according to the type of input digital audio signals and the
6 listening mode.
4. Lights in the following conditions.
7 RDS (Australian and Asian models): Receiving RDS broadcasting.
30° TUNED: Receiving AM/FM radio.
30° FM ST: Receiving FM stereo.
Approx.5 m SLEEP: When the sleep timer is set.
8
(16 ft.) AUTO STBY: When Auto Standby function is enabled.
9 5. Flashes when muting is on.
10 13 6. Displays various information of the input signals. Characters that
cannot be displayed on this unit are replaced with asterisks ( ＊ ).
14 7. Lights when operating the "NET" input selector indicating remote
controller cursor operations are possible in screens showing list of
tracks, for example.
21
License and Trademark Information wireless performance. license from Microsoft.
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac Windows and the Windows logo are trademarks of the Microsoft group of
with OS X Mountain Lion or later, and PC with iTunes 10.2.2 or later. companies.
Apple, Apple TV and Safari are trademarks of Apple Inc., registered in the U.S. QR Code is a registered trademark of DENSO WAVE INCORPORATED.
and other countries.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, “x.v.Color” and “x.v.Color” logo are trademarks of Sony Corporation.
Dolby Surround and the double-D symbol are trademarks of Dolby
Laboratories. DSD and the Direct Stream Digital logo are trademarks of Sony Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
The BLUETOOTH® word mark and logos are registered trademarks owned by Thomson.
Bluetooth SIG, Inc. and any use of such marks by Onkyo Corporation is under
license. Other trademarks and trade names are those of their respective AccuEQ, Music Optimizer, RIHD and WRAT are trademarks of Onkyo
owners. Corporation.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, the DTS-HD Onkyo Corporation does not guarantee BLUETOOTH compatibility between the
logo, and DTS-HD Master Audio are registered trademarks or trademarks of AV receiver and all BLUETOOTH enabled devices. “All other trademarks are the property of their respective owners.”
DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights For compatibility between the AV receiver and another device with
Reserved. BLUETOOTH technology, consult the device’s documentation and dealer. In “Toutes les autres marques commerciales sont la propriété de leurs détenteurs
some countries, there may be restrictions on using BLUETOOTH devices. respectifs.”
Check with your local authorities.
“El resto de marcas comerciales son propiedad de sus respectivos
Onkyo Corporation ne garantit pas la compatibilité BLUETOOTH entre l'ampli- propietarios”.
tuner AV et tous les appareils compatibles BLUETOOTH.
Pour assurer la compatibilité entre l'ampli-tuner AV et un autre périphérique à
“CINEMA FILTER” and “CINEMA FILTER (logo)” are trademarks of Onkyo technologie BLUETOOTH, consultez la documentation de l'appareil et le ϥϳϳϧόϣϟ΍ΎϬΑΎΣλϷΔϛϭϠϣϣϯέΧϷ΍ΔϳέΎΟΗϟ΍ΕΎϣϼόϟ΍ϊϳϣΟ
Corporation. vendeur. Dans certains pays, il peut exister des restrictions sur l'utilisation
d'appareils BLUETOOTH. Vérifiez auprès des autorités locales.
Onkyo Corporation no garantiza la compatibilidad BLUETOOTH entre el receptor

de AV y todos los dispositivos con tecnología BLUETOOTH.
Para obtener información sobre la compatibilidad entre el receptor de AV y otro
“VLSC” and “VLSC (logo)” are trademarks of Onkyo Corporation. dispositivo con tecnología BLUETOOTH, consulte al distribuidor y la documentación
del dispositivo. En algunos países, es posible que el uso de dispositivos
BLUETOOTH esté restringido. Consulte con las autoridades locales.
®
Εϭλϟ΍Ε΍έΎη·ϝ˶ΑϘΗγϣ˵ ϥϳΑ%/8(7227+ΙϭΗϭϠΑϟ΍ϲϓϖϓ΍ϭΗΩϭΟϭ2QN\RϥϣοΗϻ

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI %/8(7227+ΙϭΗϭϠΑϟΎΑΓΩϭίϣϟ΍ΓίϬΟϷ΍ϊϳϣΟϭΓέϭλϟ΍ϭ
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the ΙϭΗϭϠΑϟΎΑΩϭίϣέΧ΁ίΎϬΟϱ΃ϭΓέϭλϟ΍ϭΕϭλϟ΍Ε΍έΎη·ϝΑ˶ ϘΗγϣ˵ ϥϳΑϖϓ΍ϭΗϟ΍ϯΩϣϰϠϋϑέόΗϠϟ
United States and other countries. ϥϭϛΗΩϗˬϝϭΩϟ΍νόΑϲϓϝϳϛϭϟ΍ϝ΄γ΍ϭ΃ίΎϬΟϠϟΔϘϓ΍έϣϟ΍ϖ΋ΎΛϭϟ΍ΔόΟ΍έϣΑϡϗˬ%/8(7227+
ΔϳϠΣϣϟ΍ΕΎρϠγϟ΍ϊΟ΍έ%/8(7227+ΙϭΗϭϠΑϟΎΑΓΩϭίϣϟ΍ΓίϬΟϷ΍ϡ΍ΩΧΗγ΍ϰϠϋΕ΍ΩϳϳϘΗϙΎϧϫ
PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks
or registered trademarks of Pandora Media, Inc. Used with permission.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance®.
Google Cast and the Google Cast badge are trademarks of Google inc.
AirPlay, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
iPad Air and iPad mini are trademarks of Apple Inc.
“Made for iPod”, “Made for iPhone” and “Made for iPad” mean that an electronic
accessory has been designed to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple The product with this logo is conformed to Hi-Res Audio standard defined by
performance standards. Apple is not responsible for the operation of this device Japan Audio Society. This logo is used under license from Japan Audio Society.
or its compliance with safety and regulatory standards.
This product is protected by certain intellectual property rights of Microsoft. Use
Please note that the use of this accessory with iPod, iPhone or iPad may affect or distribution of such technology outside of this product is prohibited without a
22
DISCLAIMER For U.S. models
FEDERAL COMMUNICATIONS COMMISSION
Through this device you are able to link to other services or websites which are
not under the control of any company which has designed, manufactured or
DECLARATION OF CONFORMITY
distributed/have distributed this device, and its affiliates (collectively, This device complies with part 15 of the FCC Rules.
“Company”). We have no control over the nature, content and availability of Operation is subject to the following two conditions:
those services. The inclusion of any links does not necessarily imply a
recommendation or endorse the views expressed within them. (1) this device may not cause interference, and
All information, content and services available through this device belong to (2) this device must accept any interference, including
third parties and are protected by copyright, patent, trademark and/or other
intellectual property laws of applicable countries. interference that may cause undesired operation of the
The information, content and services provided through this device are for your device.
personal, noncommercial use only. Any information, content or services may
not be used in any manner other than previously approved by the appropriate Product Name: AV Receiver
content owner or service provider. Model Number: HT-R695
You may not modify, copy, republish, translate, exploit, create derivative works,
upload, post, transmit, sell or distribute in any manner any information, content Responsible Party Name: Onkyo U.S.A. Corporation
or services available through this device, unless expressly permitted by the Address: 18 PARK WAY, UPPER
appropriate copyright, patent, trademark and/or other intellectual property
owner, including, without limitation, content owner or service provider. SADDLE RIVER, NEW
THE CONTENT AND SERVICES AVAILABLE THROUGH THIS DEVICE ARE JERSEY 07458, USA
PROVIDED “AS IS”.
COMPANY DOES NOT WARRANT INFORMATION, CONTENT OR
Phone: 1-800-229-1687
SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY
PURPOSE.
COMPANY EXPRESSLY DISCLAIMS ANY WARRANTIES, EXPRESS OR
FCC Information for User
IMPLIED, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF TITLE, CAUTION:
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. The user changes or modifications not expressly approved
Company makes no representation or warranty of any kind, express or implied, by the party responsible for compliance could void the
about the completeness, accuracy, validity, legality, reliability, suitability or
availability with respect to the information, content or services available through user’s authority to operate the equipment.
this device. Company shall not be liable, whether in contract or tort, including
negligence and strict liability, for any direct, indirect, special, incidental or
consequential damages or any other damages arising out of, or in connection NOTE:
with, any information contained in, or as a result of the use of any content or This equipment has been tested and found to comply with
service by you or any third party, even if Company has been advised of the
possibility of such damages, nor shall Company be liable for any third party the limits for a Class B digital device, pursuant to Part 15 of
claims against users of this device or any third party. the FCC Rules. These limits are designed to provide
In no event shall Company be responsible nor liable for, without limiting the
generality of the foregoing, any interruption or suspension of any information, reasonable protection against harmful interference in a
content or service available through this device. Company is neither residential installation. This equipment generates, uses and
responsible nor liable for customer service related to the information, content
and services available through this device. Any question or request for service can radiate radio frequency energy and, if not installed and
relating to the information, content or services should be made directly to the used in accordance with the instructions, may cause
appropriate content owners and services providers.
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
23
SN29402324_HT-R695_BAS_En_1602xx.book 24 ページ２０１６年４月２５日　月曜日　午前１０時２４分
2-3-12 Yaesu, Chuo-ku, Tokyo 104-0028 JAPAN

http://www.onkyo.com/
<U.S.A.>
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
<Germany>
Gutenbergstrasse 3, 82178 Puchheim, Germany
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
<UK>
Anteros Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex,
HA4 6QQ United Kingdom
Tel: +44 (0)871-200-1996 Fax: +44 (0)871-200-1995
<Hong Kong>
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: +852-2429-3118 Fax: +852-2428-9039
http://www.hk.onkyo.com/
<PRC>
302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032,
Tel: +86-21-52131366 Fax: +86-21-52130396
http://www.cn.onkyo.com/
<Asia, Oceania, Middle East, Africa>
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
Корпорация О энд Пи
2-3-12, Яэсу, Чуо-ку, г. Токио, 104-0028, ЯПОНИЯ
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
F1602-0
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved. http://www.onkyo.com/privacy/
Printed in Malaysia / Imprimé en Malaisie / Напечатано в Малайзии
SN 29402324 * 2 9 4 0 2 3 2 4 *
Advan
>>Specifications >>Settings >>Listening Modes >>Playback Function >>Basic Manual
Advanced Manual Specifications

General Specifications............................................................. 2
About HDMI ............................................................................. 4
Settings
Setup Menu ............................................................................. 5
Initial Setup ............................................................................ 22
Quick Menu ........................................................................... 24
Advanced Speaker Connections ........................................... 25
Firmware Update ................................................................... 31
Listening Modes
Selecting Listening Modes..................................................... 34
Listening Mode Effects .......................................................... 35
Selectable Listening Modes................................................... 38
Playback Function
AM/FM radio .......................................................................... 48
USB Storage Device.............................................................. 50
Internet Radio ........................................................................ 52
Spotify.................................................................................... 54
Music Server.......................................................................... 55
Other Functions ..................................................................... 58
Troubleshooting�� 59
Appendix�� 64
AV RECEIVER
The Basic Manual includes information needed when starting up and
HT-R695 also instructions for frequently used operations. The Advanced Manual
has more detailed information and advanced settings.
±10 dB, 90 Hz (BASS) Communication system

±10 dB, 7.5 kHz (TREBLE) BLUETOOTH Specification version 4.1+LE
General Specifications Signal to Noise Ratio Frequency band
106 dB (IHF-A, LINE IN, SP OUT) 2.4 GHz band
80 dB (IHF-A, PHONO IN, SP OUT) Modulation method
Speaker Impedance FHSS (Freq Hopping Spread Spectrum)
■ Amplifier Section 6 Ω - 16 Ω Compatible BLUETOOTH profiles
Headphone Output Impedance A2DP 1.2
Rated Output Power (FTC) (North American) 330 Ω AVRCP 1.3
With 8 ohm loads, both channels driven, from 20- Headphone Rated Output HOGP-Host (Client)
20,000 Hz; rated 100 watts per channel minimum 90 mW (32 Ω, 1 kHz, 10% THD) HOGP-HID Device (Server)
RMS power, with no more than 0.08% total harmonic HID Service (HIDS)
distortion from 250 milliwatts to rated output. Supported Codecs
Surround Mode Output Power () ■ Video Section SBC
(6 ohms, 1 kHz THD 0.9%) 170 W per channel Signal level AAC
½½ Reference output for each speakers. 1 Vp-p/75 Ω (Composite Video) Transmission range (A2DP)
Depending on the source and the listening mode 1 Vp-p/75 Ω (Component Video Y) 20 Hz - 20 kHz (Sampling frequency 44.1 kHz)
settings, there may be no sound output. 0.7 Vp-p/75 Ω (Component Video B/R) Maximum communication range
Rated Output Power (IEC) (Others) Maximum resolution supported by component video Line of sight approx. 15 m ()
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch driven of 1% 480i/576i ½½ The actual range will vary depending on factors
THD such as obstacles between devices, magnetic fields
Maximum Effective Output Power (JEITA) (Asian and around a microwave oven, static electricity, cordless
Australian) ■ Tuner Section phone, reception sensitivity, antenna's performance,
7 ch × 175 W at 6 ohms, 1 kHz, 1 ch driven of 10% FM Tuning Frequency Range operating system, software application, etc.
THD 87.5 MHz - 107.9 MHz (North American)
Dynamic Power () 87.5 MHz - 108.0 MHz, RDS (Others)
½½ IEC60268-Short-term maximum output power AM Tuning Frequency Range
■ General
240 W (3 Ω, Front) 530 kHz - 1710 kHz (North American) Power Supply
210 W (4 Ω, Front) 522/530 kHz - 1611/1710 kHz (Others) AC 120 V, 60 Hz (North American)
120 W (8 Ω, Front) Preset Channel AC 220 - 240 V, 50/60 Hz (Others)
THD+N (Total Harmonic Distortion+Noise) 40 Power Consumption
0.08% (20 Hz - 20,000 Hz, half power) 580 W (North American)
Input Sensitivity and Impedance (1 kHz 100 W/8 Ω) 570 W (Others)
200 mV/47 kΩ (LINE (Unbalance)) ■ Network Section 0.1 W (Stand-by, North American)
3.5 mV/47 kΩ (PHONO MM) Ethernet LAN 0.15 W (Stand-by, Others)
Rated RCA Output Level and Impedance 10BASE-T/100BASE-TX 65 W (No-sound)
1 V/470 Ω (SUBWOOFER PRE OUT) Wireless LAN 5.0 W (HDMI Standby Through, North American)
200 mV/2.3 kΩ (ZONE LINE OUT) IEEE 802.11 a/b/g/n standard 5.1 W (HDMI Standby Through, Others)
Phono Overload (Wi-FiR standard) 2.4 W (Network Standby)
70 mV (MM 1 kHz 0.5%) 5 GHz/2.4 GHz band Dimensions (W × H × D)
Frequency Response 435 mm × 173.5 mm × 378 mm
10 Hz - 100 kHz/+1 dB, –3 dB (Direct/Pure Audio) 17-1/8" × 6-13/16" × 14-7/8"
Tone Control Characteristics ■ BLUETOOTH Section
2
Weight supports 4K, 1080p HDMI video signals can also be notice.
10.0 kg (22.0 lbs.) output as 4K.
■ HDMI ■ Audio Inputs

Input Digital
IN1 (BD/DVD, HDCP2.2), IN2 (CBL/SAT, HDCP2.2), OPTICAL 1 (CD), 2 (TV)
IN3 (STRM BOX, HDCP2.2), IN4 (GAME), IN5 (PC), COAXIAL (BD/DVD)
IN6, IN7, AUX INPUT HDMI (front) Analog
Output BD/DVD, CBL/SAT, GAME, STRM BOX, CD, TV,
OUT MAIN (ARC), OUT SUB PHONO, AUX (front)
Supported
Deep Color, x.v.Color™, LipSync, Audio Return
Channel, 3D, 4K 60 Hz, CEC, Extended Colorimetry ■ Audio Outputs
(sYCC601, Adobe RGB, Adobe YCC601), Content Analog
Type, HDR ZONE2 LINE OUT
Audio Format 2 SUBWOOFER PRE OUT
Dolby Atmos, Dolby TrueHD, Dolby Digital, Dolby Speaker Outputs
Digital Plus, DTS, DTS:X (to be supported in a FRONT L/R, CENTER, SURROUND L/R,
future update), DTS-HD Master Audio, DTS-HD High SURROUND BACK or HEIGHT L/R, ZONE2 L/R
Resolution Audio, DTS 96/24, DTS-ES, DTS-HD (North American models are banana plug ready)
Express, DSD, PCM Phones
Maximum Video Resolution PHONES (Front, ø 6.3 mm, 1/4")
4k 60 Hz (YCbCr 4:4:4)
■ Others
■ Video Inputs Setup Mic : 1 (Front)
Component USB : 1 (Ver. 2.0, 5 V/1 A)
IN1 (BD/DVD), IN2 (GAME) Ethernet : 1
Composite
IN1 (CBL/SAT), IN2 (STRM BOX)
■ Power consumption in standby mode
• In the following cases, the power consumption in
■ Compatible input resolutions standby mode may reach up to a maximum of 12 W:
HDMI input – When "Network Standby" is set to "On"
4K, 1080p/24, 1080p, 1080i, 720p, 480p/576p – When "HDMI CEC" is set to "On"
Component input – When "HDMI Standby Through" is set to other than
480i/576i "Off"
Composite input – When "Bluetooth Wakeup" is set to "On"
480i/576i – When "USB Power Out at Standby" is set to "On"
• The output from the HDMI OUT jack to the TV is the
same resolution as the input. When using a TV that
Specifications and features are subject to change without
3
ARC（Audio Return Channel）: Multi-channel linear PCM:

By connection a TV that supports ARC with a single HDMI Maximum 7.1 channels, 32 kHz, 44.1 kHz, 48 kHz,
About HDMI cable, you can not only output the audio and video from 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit
this unit to the TV, but also input the audio from the TV to
Bitstream:
this unit.
Dolby Atmos, Dolby Digital, Dolby Digital Plus, Dolby
HDMI Standby Through: TrueHD, DTS, DTS:X (to be supported in a future update),
■ Compatible functions Even if this unit is in standby, the input signals from AV DTS-HD High Resolution Audio, DTS-HD Master Audio
HDMI (High Definition Multimedia Interface) is a digital components are transmitted to the TV. DSD:
interface standard for connecting TVs, projectors, Blu- Supported sampling rates: 2.8 MHz
ray Disc/DVD players, set-top boxes, and other video Deep Color:
By connecting devices supporting Deep Color, video Your Blu-ray Disc/DVD player must also support HDMI
components. Until now, several separate video and audio
signals input from the devices can be reproduced on the output of the above audio formats.
cables have been required to connect AV components.
With HDMI, a single cable can carry control signals, digital TV with even more colors.
video and digital audio (2 ch PCM, multichannel digital x�v�Color™: ■ Supported resolutions
audio, and multichannel PCM). This technology realizes even more realistic colors by HDMI IN1 to IN3:
HDMI CEC functionality: broadening the color gamut. • Copyright protection technology: HDCP1.4/HDCP2.2
By connecting devices and HDMI cables that comply with • Color space (Color Depth):
3D:
the CEC (Consumer Electronics Control) specification of – 720×480i 60Hz, 720×576i 50Hz, 720×480p
You can transmit 3D video signals from AV components to
the HDMI standard, a variety of linked operation become 60Hz, 720×576p 50Hz, 1920×1080i 50/60Hz,
the TV.
possible between devices. You can enjoy features such as 1280×720p 24/25/30/50/60Hz, 1680×720p
linking input switching with the input selector and players, 4K: 24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz,
control volume using the remote controller of the TV, and This unit supports 4K (3840×2160p) and 4K SMPTE 2560×1080p 24/25/30/50/60Hz, 4K (3840×2160p)
automatically switching this unit to standby when the TV is (4096×2160p) video signals. 24/25/30Hz, 4K SMPTE (4096×2160p) 24/25/30Hz :
turned off. RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit)
The unit is designed to link with products that comply with LipSync: – 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096
the CEC standard, and that linked operation is not always This setting automatically corrects any desynchronization ×2160p) 50/60Hz : RGB/YCbCr4:4:4 (8 bit),
guaranteed with all CEC devices. For linked functions between the video and audio signals based on data from YCbCr4:2:2 (12 bit), YCbCr4:2:0 (8/10/12 bit)
to work properly, do not connect more CEC-compliant the HDMI LipSync compatible TV.
HDMI IN4 to IN7, Front:
components than the quantities specified below, to the • Copyright protection technology: HDCP1.4
Copyright Protection:
HDMI jack. • Color space (Color Depth):
The unit supports Revision 1.4 and Revision 2.2 (HDMI
• Blu-ray Disc/DVD players: up to 3 units. – 720×480i 60Hz, 720×576i 50Hz, 720×480p
OUT MAIN/SUB and HDMI IN1 to 3 only) of the HDCP
• Blu-ray Disc/DVD recorders: up to 3 units. 60Hz, 720×576p 50Hz, 1920×1080i 50/60Hz,
(High-bandwidth Digital Content Protection), a copy-
• Cable TV tuner, terrestrial digital tuner, and satellite 1280×720p 24/25/30/50/60Hz, 1680×720p
protection system for digital video signals. Other devices
broadcasting tuner: up to 4 units. 24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz,
connected to the unit must also support HDCP.
Operation has been confirmed on the following devices: 2560×1080p 24/25/30/50/60Hz : RGB/YCbCr4:4:4
(As of February 2016) (8/10/12 bit), YCbCr4:2:2 (12 bit)
Toshiba brand televisions; Sharp brand televisions; Onkyo ■ Supported Audio Formats – 4K (3840×2160p) 24/25/30Hz, 4K SMPTE (4096
and Integra brand RIHD-compatible players; Toshiba brand ×2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8 bit),
2 ch linear PCM:
players and recorders; Sharp brand players and recorders YCbCr4:2:2 (12 bit)
32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz,
(when used with a Sharp brand television) – 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096×
192 kHz, 16/20/24 bit
2160p) 50/60Hz : YCbCr4:2:0 (8 bit)
4
1� Input/Output Assign
Setup Menu Make settings related to output to the TV, change the settings for jack allocations to the
various input selectors, and set the feature for displaying operations on the TV (OSD), etc.
■ 1� TV Out / OSD
The unit allows you to configure advanced settings to provide you with an even better
experience.
Setting Item Default Value Setting Details
HDMI Out MAIN Select the HDMI jack to be connected with the TV.
Operation:
"MAIN": When connecting the TV to the HDMI OUT
Use the on-screen displays (OSD) that appear on the TV to make the settings.
MAIN jack
Press on the remote controller to display the Setup menu.
"SUB": When connecting the TV to the HDMI OUT
SUB jack
Setup
"MAIN+SUB": When connecting to both the MAIN
1. Input/Output Assign 1. TV Out / OSD
and SUB jacks
2. Speaker 2. HDMI Input
3. Audio Adjust 3. Video Input 1080p -> 4K Off When using a TV that supports 4K, video signals
4. Source 4. Digital Audio Input
Upscaling input at 1080p can be automatically upscaled to 4K
5. Hardware 5. Analog Audio Input
6. Multi Zone
for output.
7. Miscellaneous "Off": Do not use this function
"Auto": Use this function
• Select "Off" if your TV does not support 4K.
Select the item with the cursor / buttons of the remote controller and press ENTER to Super Resolution (2) When you have set "1080p -> 4K Upscaling" to
confirm your selection. "Auto", you can select the degree of video signal
Use the cursors / to change the default values. correction from "Off" and between "1" (weak) and
• To return to the previous screen, press . "3" (strong).
• To exit the settings, press .
OSD Language English Select the on-screen display language from the
following.
(North American models) English, German, French,
Spanish, Italian, Dutch, Swedish
(European, Australian and Asian models) English,
German, French, Spanish, Italian, Dutch, Swedish,
Russian, Chinese
5
Setting Item Default Value Setting Details Setting Item Default Value Setting Details
Impose OSD On Set whether or not to display the information on PC HDMI 5 "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
the TV when the volume is adjusted or input is desired HDMI IN jack to the PC button. If you do
changed, for example. not assign a jack, select "-----". To select an HDMI
"On": OSD displayed on the TV IN jack already assigned to another input selector,
"Off": OSD not displayed on the TV change its setting to "-----" first.
• OSD may not be displayed depending on the CD ----- "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
input signal even if "On" is selected. If the desired HDMI IN jack to the CD button. If you do
operation screen is not displayed, change the not assign a jack, select "-----". To select an HDMI
resolution of the connected device. IN jack already assigned to another input selector,
Screen Saver 3 minutes Set the time to start the screen saver. change its setting to "-----" first.
Select a value from "3 minutes", "5 minutes", "10 TV ----- "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
minutes" and "Off". desired HDMI IN jack to the TV button. If you do
not assign a jack, select "-----". To select an HDMI
IN jack already assigned to another input selector,
■ 2� HDMI Input change its setting to "-----" first.
You can change input assignment between the input selectors and HDMI IN jacks. PHONO ----- "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
desired HDMI IN jack to the PHONO button. If you
Setting Item Default Value Setting Details do not assign a jack, select "-----". To select an
HDMI IN jack already assigned to another input
BD/DVD HDMI 1 "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
selector, change its setting to "-----" first.
（HDCP 2.2） desired HDMI IN jack to the BD/DVD button. If you
do not assign a jack, select "-----". To select an
CBL/SAT HDMI 2 "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
（HDCP 2.2） desired HDMI IN jack to the CBL/SAT button. If
you do not assign a jack, select "-----". To select
an HDMI IN jack already assigned to another input
GAME HDMI 4 "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
desired HDMI IN jack to the GAME button. If you
do not assign a jack, select "-----". To select an
STRM BOX HDMI 3 "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a
（HDCP 2.2） desired HDMI IN jack to the STRM BOX button.
If you do not assign a jack, select "-----". To select
an HDMI IN jack already assigned to another input
6
■ 3� Video Input Setting Item Default Value Setting Details

You can change input assignment between the input selectors and COMPONENT VIDEO PHONO ----- "COMPONENT 1", "COMPONENT 2": Assign the
IN 1 and 2 jacks and the VIDEO IN 1 and 2 jacks. If you do not assign a jack, select "-----". COMPONENT VIDEO IN jacks to the PHONO
button.
Setting Item Default Value Setting Details "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN
jack to the PHONO button.
BD/DVD COMPONENT 1 "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the BD/DVD
button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN
jack to the BD/DVD button.
CBL/SAT VIDEO 1 "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the CBL/SAT
button.
jack to the CBL/SAT button.
GAME COMPONENT 2 "COMPONENT 1", "COMPONENT 2": Assign
the COMPONENT VIDEO IN jacks to the GAME
button.
jack to the GAME button.
STRM BOX VIDEO 2 "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the STRM BOX
button.
jack to the STRM BOX button.
PC ----- "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the PC button.
"VIDEOI 1" to "VIDEO 2": Assign a desired VIDEO
IN jack to the PC button.
CD ----- "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the CD button.
jack to the CD button.
TV ----- "COMPONENT 1", "COMPONENT 2": Assign the
COMPONENT VIDEO IN jacks to the TV button.
jack to the TV button.
7
■ 4� Digital Audio Input ■ 5� Analog Audio Input

You can change input assignment between the input selectors and DIGITAL IN COAXIAL/ You can change input assignment between the input selectors and AUDIO IN jacks. If you
OPTICAL 1 to 2 jacks. If you do not assign a jack, select "-----". do not assign a jack, select "-----".
BD/DVD COAXIAL "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a BD/DVD AUDIO 1 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the BD/DVD button. IN jack to the BD/DVD button.
CBL/SAT ----- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a CBL/SAT AUDIO 2 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the CBL/SAT button. IN jack to the CBL/SAT button.
GAME ----- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a GAME AUDIO 3 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the GAME button. IN jack to the GAME button.
STRM BOX ----- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a STRM BOX AUDIO 4 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the STRM BOX button. IN jack to the STRM BOX button.
PC ----- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a PC ----- "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the PC button. IN jack to the PC button.
CD OPTICAL 1 "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a CD AUDIO 5 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the CD button. IN jack to the CD button.
TV OPTICAL 2 "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a TV AUDIO 6 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO
desired DIGITAL IN jack to the TV button. IN jack to the TV button.
PHONO ----- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a PHONO PHONO The setting cannot be changed.
desired DIGITAL IN jack to the PHONO button.
• Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32kHz, 44.1kHz,
48kHz, 88.2kHz, 96kHz/16bit, 20bit, and 24bit.
8
2� Speaker Setting Item Default Value Setting Details

Bi-Amp No Set whether the front speakers are bi-amp
You can make changes to the connection environment of the speakers and change the
connected.
volume level. Settings are automatically configured if you use AccuEQ Room Calibration.
"No": When front speakers are not bi-amp
This setting cannot be selected if headphones are connected or audio is output from the
connected
speakers of the TV.
"Yes": When front speakers are bi-amp connected
• This item will be fixed to "No" when the "Zone
■ 1� Configuration Speaker" setting is "Zone 2".
• This setting cannot be selected when surround
Setting Item Default Value Setting Details back speakers or height speakers are installed.
Speaker 5.1.2 ch Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1
Channels ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch", or
"5.1.2 ch" to suit the number of speaker channels
connected.
Subwoofer Yes Set whether a subwoofer is connected or not.
"Yes": When subwoofer is connected
"No": When subwoofer is not connected
Height Speaker Bundled Dolby Set the speaker type if height speakers are
Speaker connected to the SURROUND BACK or HEIGHT
terminals.
Select "Front High", "Top Front", "Top Middle",
"Top Rear", "Rear High", "Dolby Speaker (Front)",
"Dolby Speaker (Surr)", or "Bundled Dolby
Speaker" according to the type and layout of the
connected speakers.
• If an item cannot be selected even though
connection is correct, check that the settings
in "Speaker Channels" matches the number of
connected channels.
Zone Speaker No Set the connection of speakers to Zone 2 speaker
terminals.
"Zone 2": When speakers are connected to Zone 2
speaker terminals
"No": When speakers are not connected to Zone 2
speaker terminals
9
■ 2� Crossover Setting Item Default Value Setting Details

Surround 100Hz Select the crossover frequency from "40Hz" to
Setting Item Default Value Setting Details "200Hz" to start outputting frequencies for each
Front 100Hz Select the crossover frequency from "40Hz" to channel.
"200Hz" to start outputting frequencies for each "Full Band": Full band will be output.
channel. • "Full Band" can be selected only when "Front" is
"Full Band": Full band will be output. set to "Full Band".
• If "Configuration" - "Subwoofer" is set to "No", • If an item cannot be selected even though
"Front" will be fixed to "Full Band" and the low connection is correct, check that the settings in
pitched range of the other channels will be "Configuration" - "Speaker Channels" matches
output from the front speakers. Refer to the the number of connected channels.
instruction manual of your speakers to make the Surround Back (100Hz) Select the crossover frequency from "40Hz" to
setting. "200Hz" to start outputting frequencies for each
Center 100Hz Select the crossover frequency from "40Hz" to channel.
"200Hz" to start outputting frequencies for each "Full Band": Full band will be output.
channel. • "Full Band" can be selected only when
"Full Band": Full band will be output. "Surround" is set to "Full Band".
• "Full Band" can be selected only when "Front" is • If an item cannot be selected even though
set to "Full Band". connection is correct, check that the settings in
• If an item cannot be selected even though "Configuration" - "Speaker Channels" matches
connection is correct, check that the settings in the number of connected channels.
"Configuration" - "Speaker Channels" matches LPF of LFE 120Hz Set the low-pass filter for LFE (low-frequency
the number of connected channels. effect) signals in order to pass lower frequency
Height 180Hz Select the crossover frequency from "40Hz" to signals than the set value and thus cancel
"200Hz" to start outputting frequencies for each unwanted noises. The low-pass filter will be
channel. effective only on sources with LFE channel.
"Full Band": Full band will be output. The value from "80Hz" to "120Hz" can be set.
• "Full Band" can be selected only when "Front" is "Off": Do not use this function
set to "Full Band". Double Bass (On) This can be selected only when "Configuration"
• If an item cannot be selected even though - "Subwoofer" is set to "Yes" and "Front" is set to
connection is correct, check that the settings in "Full Band".
"Configuration" - "Speaker Channels" matches Boost bass output by feeding bass sounds from
the number of connected channels. the front left and right, and center speakers to the
subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
• The setting will not automatically be configured
even if you performed AccuEQ Room
Calibration.
10
■ 3� Distance ■ 4� Level Calibration

Set the distance from each speaker to the listening position.
Setting Item Default Value Setting Details Front Left 0 dB Select a value between "－12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
Front Left 12.0ft/3.60m Specify the distance between each speaker and
each time you change the value. Select the desired
the listening position.
level.
Center 12.0ft/3.60m Specify the distance between each speaker and
Center 0 dB Select a value between "－12 dB" and "＋12 dB"
Front Right 12.0ft/3.60m Specify the distance between each speaker and each time you change the value. Select the desired
the listening position. level.
Height Left 9.0ft/2.70m Specify the distance between each speaker and Front Right 0 dB Select a value between "－12 dB" and "＋12 dB"
the listening position. (in 1 dB increments). A test tone will be output
• The setting cannot be changed if "Zone 2" is set in each time you change the value. Select the desired
"Configuration" - "Zone Speaker" and Zone 2 is on. level.
Height Right 9.0ft/2.70m Specify the distance between each speaker and Height Left 0 dB Select a value between "－12 dB" and "＋12 dB"
the listening position. (in 1 dB increments). A test tone will be output
• The setting cannot be changed if "Zone 2" is set in each time you change the value. Select the desired
"Configuration" - "Zone Speaker" and Zone 2 is on. level.
Surround Right 7.0ft/2.10m Specify the distance between each speaker and • The setting cannot be changed if "Zone 2" is set
the listening position. in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surr Back Right (7.0ft/2.10m) Specify the distance between each speaker and
the listening position. Height Right 0 dB Select a value between "－12 dB" and "＋12 dB"
• The setting cannot be changed if "Zone 2" is set in (in 1 dB increments). A test tone will be output
"Configuration" - "Zone Speaker" and Zone 2 is on. each time you change the value. Select the desired
level.
Surr Back Left (7.0ft/2.10m) Specify the distance between each speaker and • The setting cannot be changed if "Zone 2" is set
the listening position. in "Configuration" - "Zone Speaker" and Zone 2
• The setting cannot be changed if "Zone 2" is set in is on.
"Configuration" - "Zone Speaker" and Zone 2 is on.
Surround Right 0 dB Select a value between "－12 dB" and "＋12 dB"
Surround Left 7.0ft/2.10m Specify the distance between each speaker and (in 1 dB increments). A test tone will be output
the listening position. each time you change the value. Select the desired
Subwoofer 12.0ft/3.60m Specify the distance between each speaker and level.
• Default values vary depending on the regions.

• Distance units can be switched by pressing MODE on the remote controller. When the unit is set as
feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1ft. When the unit is set as meters, you
can set between 0.03 m and 9.00 m in increments of 0.03 m.
11
Setting Item Default Value Setting Details ■ 6� Equalizer Settings

Surr Back Right (0 dB) Select a value between "－12 dB" and "＋12 dB" You can adjust the output volume of the range of each connected speaker. You can adjust
(in 1 dB increments). A test tone will be output the volume of the different sound ranges for each of the speakers. You can set three
each time you change the value. Select the desired different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
level. nine bands for all other speakers.
• The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2 Setting Item Default Value Setting Details
is on.
Front 0 dB After selecting the speaker frequency from
Surr Back Left (0 dB) Select a value between "－12 dB" and "＋12 dB" between 25 Hz" and "16 kHz" with the cursors
(in 1 dB increments). A test tone will be output / , adjust the volume of that frequency between
each time you change the value. Select the desired "－6 dB" and "＋6 dB" with / .
level.
Center 0 dB After selecting the speaker frequency from
• The setting cannot be changed if "Zone 2" is set
between 25 Hz" and "16 kHz" with the cursors
in "Configuration" - "Zone Speaker" and Zone 2
/ , adjust the volume of that frequency between
is on.
"－6 dB" and "＋6 dB" with / .
Surround Left 0 dB Select a value between "－12 dB" and "＋12 dB"
Height 0 dB After selecting the speaker frequency from
level.
"－6 dB" and "＋6 dB" with / .
Subwoofer 0 dB Select a value between "－15 dB" and "＋12 dB" • This cannot be selected if "Zone 2" is set in
(in 1 dB increments). A test tone will be output "Configuration" - "Zone Speaker" and Zone 2 is on.
Surround 0 dB After selecting the speaker frequency from
level.
"－6 dB" and "＋6 dB" with / .
■ 5� Dolby Enabled Speaker
Surround Back (0 dB) After selecting the speaker frequency from
Dolby Enabled 6.0 ft/1.80 m Set the distance between the Dolby Enabled "－6 dB" and "＋6 dB" with / .
Speaker to Speaker and the ceiling. Select between "0.1 • This cannot be selected if "Zone 2" is set in
Ceiling ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units). "Configuration" - "Zone Speaker" and Zone 2 is on.
• The unit of distance (ft/m) shown is the unit
Subwoofer 0 dB After selecting the speaker frequency from
selected for use in "Distance".
between 25 Hz" and "160 Hz" with the cursors
AccuReflex Off You can enhance the reflection effect of Dolby / , adjust the volume of that frequency between
Enabled Speakers from the ceiling. "－6 dB" and "＋6 dB" with / .
"Off": Do not use this function • This cannot be selected if "No" is set in
"On": Use this function "Configuration" - "Subwoofer".
• The result may not be as expected depending on the input source and listening mode setting.
12
3� Audio Adjust ■ 3� LFE Level

Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel
Make advanced settings such as those related to multiplex audio, settings for the LFE level, PCM, and DSD signals.
or those related to the volume of this unit.

■ 1� Multiplex/Mono
LFE Level 0 dB Select the low-frequency effect (LFE) level of each
type of signal from "0dB" to "－∞dB". If the low-
Setting Item Default Value Setting Details frequency effect sound is too strong, select
Multiplex Input Main Set the audio channel or language to be output "－20dB" or "－∞dB".
Channel when playing multiplex audio or multilingual TV
broadcasts etc.
"Main": Main channel only ■ 4� Volume
"Sub": Sub channel only
"Main/Sub": Main and sub channels will be output Setting Item Default Value Setting Details
at the same time.
• If multiplex audio is being played, "1＋1" will be Mute Level －∞dB Set the volume lowered from the listening volume
displayed when on the remote controller is when muting is on. Select a value from "－∞dB",
pressed. "－40dB", and "－20dB".
Mono Input Left + Right Set the input channel to use for playing any 2 ch Maximum Volume Off Set the maximum value to avoid too high volume.
Channel digital source such as Dolby Digital, or 2 ch analog/ Select a value from "Off", "50" to "99".
PCM source in the Mono listening mode. Power On Volume Last Set the volume level of when the power is turned
"Left": Left channel only on. Select a value from "Last" (Volume level before
"Right": Right channel only entering standby mode), "Min", "1" to "99" and
"Left + Right" : Left and right channels "Max".
• You cannot set a higher value than that of
"Maximum Volume".
■ 2� Dolby Headphone Level 0 dB Adjust the output level of the headphones. Select a
value between "－12 dB" and "＋12 dB".
Loudness On When playing Dolby TrueHD, enable the dialog
Management normalization function which keeps the volume of
dialog at a certain level. Note that when this setting
is Off, the Late Night function that allows you to
enjoy surround at low volumes is fixed to off when
playing Dolby Digital Plus/Dolby TrueHD.
"On": Use this function
"Off": Do not use this function
13
4� Source • To name a preset radio station, press TUNER on the remote controller, select AM/FM and select the
preset number.
• This cannot be set if the "NET" or "BLUETOOTH" input is selected.
Make settings for input sources, such as volume difference adjustments for each input
selector for the connected equipment.
■ Audio Select
■ 1� IntelliVolume Select the priority for input selection when multiple audio sources are connected to one
input selector, such as connections to both the "BD/DVD" HDMI IN jack and the "BD/DVD"
Adjust the volume level difference between the devices connected to the unit. Select the
AUDIO IN jack. The setting can be separately set to each input selector button. Select the
input selector to configure.
input selector to configure.

IntelliVolume 0 dB Select a value between "－12 dB" and "＋12 dB".
Audio Select BD/DVD: "ARC": When giving priority to input signal from
Set a negative value if the volume of the target
HDMI ARC compatible TV.
device is larger than the others and a positive
CBL/SAT: • The setting can be selected only when
value if smaller. To check the audio, start playback
HDMI "5. Hardware" - "HDMI" - "Audio Return
of the connected device.
GAME: Channel" is set to "Auto" and also the "TV" input
• This function is not effective in Zone 2.
HDMI is selected.
STRM BOX: "HDMI": When giving priority to input signal from
HDMI HDMI IN jacks
■ 2� Name Edit PC: • The setting can be selected only when the input
Set an easy name to each input. The set name will be shown on the main unit display. HDMI is assigned to the HDMI jack in the "1. Input/
Select the input selector to configure. AUX: Output Assign" - "HDMI Input" setting.
HDMI "COAXIAL": When giving priority to input signal
Setting Item Default Value Setting Details CD: from DIGITIAL IN COAXIAL jacks
OPTICAL • The setting can be selected only when the input
Name Edit Input name 1. Select a character or symbol with the cursors PHONO: is assigned to the COAXIAL jack in the "1. Input/
and press ENTER. Analog Output Assign" - "Digital Audio Input" setting.
Repeat it to input 10 or less characters. TV: "OPTICAL": When giving priority to input signal
"A/a": Switches between upper and lower cases. OPTICAL from DIGITIAL IN OPTICAL jacks
(Pressing MODE on the remote controller also • The setting can be selected only when the input
toggles between upper and lower cases) is assigned to the OPTICAL jack in the "1. Input/
"←" "→": Moves the cursor to the arrow Output Assign" - "Digital Audio Input" setting.
direction. "Analog": To always output analog audio
" ": Removes a character on the left of the independently of the input signal
cursor. • The setting can be selected only when the
" ": Enters a space. input is assigned to the AUDIO IN jack in the
• Pressing CLEAR on the remote controller "1. Input/Output Assign" - "Analog Audio Input"
will remove all the input characters. setting.
2. After inputting, select "OK" with the cursors and
press ENTER.
The input name will be saved.
14
Setting Item Default Value Setting Details 5� Hardware

PCM Fixed Mode Off Select whether to fix input signals to PCM (except
Make settings related to the HDMI CEC, HDMI Standby Through, ARC features, settings
multi-channel PCM) when you have selected
related to network features, and settings related to power management of the unit, such as
"HDMI", "COAXIAL", or "OPTICAL" in the "Audio
Auto Standby and Network Standby.
Select" setting. Set this item to "On" if noise is
produced or truncation occurs at the beginning of
a track when playing PCM sources. Select "Off" ■ 1� HDMI
normally.
• Changing "Audio Select" changes the setting to Setting Item Default Value Setting Details
"Off".
HDMI CEC Off Setting to "On" enables the input selection link and
• The setting cannot be changed when "TUNER", "NET", or "BLUETOOTH" input is selected. other link functions with HDMI connected CEC
compliant device.
■ Video Select "Off": Do not use this function
When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from When changing this setting, turn off and then on
which video is displayed on the TV. again the power of all connected components.
• Depending on the TV set, a link may need to be
configured on the TV.
• This function is effective only when the device is
Video Select Last "Last": Select the video input played immediately connected to the HDMI OUT MAIN terminal.
prior. • Setting to "On" and closing the on-screen menu
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", displays the name of the CEC-compatible
"PC", "AUX", "CD", "TV", "PHONO": Play the video components and "CEC On" on the display.
from the selected input. • Power consumption in standby mode may
• This setting is effective for an input selector increase if "On" is set. (Depending on the TV
which is assigned in "1. Input/Output Assign" - status, the unit will enter the normal standby
"HDMI Input" and "Video Input". mode.)
• If you operate the MASTER VOLUME dial on
• If the OSD language is set to Chinese, you can only select this setting when "TUNER" is selected as the main unit when this setting is "On" and
input. (European, Australian and Asian models) audio is output from the TV speakers, audio will
be output also from the speakers connected to
the unit. If you want to output from only either of
them, change the unit or TV settings, or reduce
the volume of the unit.
• If abnormal operation occurs when you set the
setting to "On", set it to "Off".
• When connecting a non-CEC compatible
component, or when you are not sure whether it
is compatible, set the setting to "Off".
15
HDMI Standby Off When this is set to anything other than "Off", Audio TV Out Off You can enjoy audio through the speakers of the
Through you can play the video and audio of an HDMI TV while this unit is on.
connected player on the TV even if the unit is in "On": Use this function
standby mode. Only "Auto" and "Auto(Eco)" can be "Off": Do not use this function
selected if "HDMI CEC" is set to "On". If you select • This setting is fixed to "Auto" if you have set
anything else, set "HDMI CEC" to "Off". "1. Input/Output Assign" - "TV Out/OSD" -
• Power consumption in standby mode increases "HDMI Out" or "Other" - "HDMI Out" in the
if set to anything other than "Off". "Quick Menu" to "MAIN" or "MAIN+SUB" and
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "HDMI CEC is set to "On". If you change this
"PC", "AUX", "CD", "TV", "PHONO": For example, setting, set "HDMI CEC" to "Off".
if you select "BD/DVD", you can play the • Listening mode cannot be changed while "Audio
equipment connected to the "BD/DVD" jack on the TV Out" is set to "On" and audio is being output
TV even if the unit is in standby mode. Select this through the speakers of the TV.
setting if you have decided which player to use with • Depending on your TV set or input signal of the
this function. component, audio may not output through the
"Last": You can play the video and audio of the speakers of the TV even if this setting is set
input selected immediately prior to the unit being to "On". In such case, audio is output from the
switched to standby on the TV. When "Last" is speakers of the unit.
selected, you can switch the input of the unit even • If you operate the MASTER VOLUME dial on
in the standby mode with the remote controller or this unit when audio that is being input through
the Onkyo Remote app. this unit for output from the TV speakers, audio
"Auto", "Auto (Eco)": Select one of these settings is output from this unit. If you do not want to
when you have connected equipment that output audio from the unit, change the unit or TV
conforms to the CEC standard. You can play the settings, or reduce the volume of the unit.
video and audio of the input selected on the TV, Audio Return (Auto) (＊) You can enjoy sound of the HDMI connected ARC
irrespective of what input was selected immediately Channel compatible TV through the speakers connected to
prior to the unit being switched to standby, using the unit.
the CEC link function. ＊ To use this function, set "HDMI CEC" to "On" in
• To play players on the TV that do not conform to advance.
the CEC standard, you will need to turn the unit "Auto": When enjoying the TV sound through the
on and switch to the relevant input. speakers connected to the unit
• When using TV that complies with the "Off": When not using the ARC function
CEC standard, you can reduce the power
consumption in standby mode by selecting Auto LipSync On This setting automatically corrects any
"Auto (Eco)". desynchronization between the video and audio signals
based on data from the HDMI LipSync compatible TV.
"On": Automatic correction will be enabled
"Off": Automatic correction will be disabled
16
■ 2� Network Setting Item Default Value Setting Details

• When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the Friendly Name Onkyo HT-R695 Change the device name for this unit which is
setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each XXXXXX shown on other devices connected to the network
components, you must set "DHCP" to "Disable" and assign an address to this unit in to an easily recognized name.
"IP Address" as well as set information related to your LAN, such as Subnet Mask and 1. Press ENTER to display the Edit screen.
Gateway. 2. Select a character or symbol with the cursors
and press ENTER.
Setting Item Default Value Setting Details Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower
Wi-Fi Off(Wired) Connect the unit to network via wireless LAN
cases. (Pressing MODE on the remote
router.
controller also toggles between upper and
"On": Wireless LAN connection
lower cases.)
"Off(Wired)": Wired LAN connection
"←" "→": Moves the cursor to the arrow
Wi-Fi Setup ‐ You can configure wireless LAN settings by direction.
pressing ENTER when "Start" is displayed. " ": Removes a character on the left of the
Wi-Fi Status ‐ The information of the connected access point will cursor.
be displayed. " ": Enters a space.
"SSID": SSID of the connected access point. • Pressing CLEAR on the remote controller
"Signal": Signal strength of the connected access will remove all the input characters.
point. 3. After inputting, select "OK" with the cursors and
"Status": Status of the connected access point. press ENTER.
The input name will be saved.
MAC Address ‐ This is the MAC address of this unit.
This value is specific to the component and cannot
be changed.
DHCP Enable "Enable": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
• If selecting "Disable", you must set "IP Address",
"Subnet Mask", "Gateway", and "DNS Server"
manually.
IP Address 0.0.0.0 Displays/Sets the IP address.
Subnet Mask 0.0.0.0 Displays/Sets the subnet mask.
Gateway 0.0.0.0 Displays/Sets the gateway.
DNS Server 0.0.0.0 Displays/Sets the primary DNS server.
Proxy URL ‐ Displays/Sets the proxy server URL.
Proxy Port 8080 Displays/Sets the proxy server port number when
you enter "Proxy URL".
17
• Wait for a while if "Network" cannot be selected. It will appear when the network feature is started.
AirPlay Password You can set a password of up to 31 characters so
that only registered users can use AirPlayR. ■ 3� Bluetooth
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors Setting Item Default Value Setting Details
and press ENTER.
Bluetooth On Select whether or not to use the BLUETOOTH
Repeat it to input 31 or less characters.
function.
"A/a": Switches between upper and lower
"On": Enables connection with a BLUETOOTH
cases. (Pressing MODE on the remote
enabled device by using the BLUETOOTH
controller also toggles between upper and
function. Select "On" also when making various
lower cases.)
BLUETOOTH settings.
"←" "→": Moves the cursor to the arrow
"Off": When not using the BLUETOOTH function
direction.
" ": Removes a character on the left of the Auto Input On The input of the unit will automatically be switched
cursor. Change to "BLUETOOTH" when connection is made from
" ": Enters a space. a BLUETOOTH enabled device to the unit.
• To select whether to mask the password "On": The input will automatically become
with "＊" or display it in plain text, press "BLUETOOTH" when a BLUETOOTH enabled
MEMORY on the remote controller. device is connected.
• Pressing CLEAR on the remote controller "Off": The function is disabled.
will remove all the input characters. • If the input is not switched automatically, set to
3. After inputting, select "OK" with the cursors and "Off" and change the input manually.
press ENTER.
Auto Reconnect On This function automatically reconnects to the
The input password will be saved.
BLUETOOTH enabled device connected last
Usage Data No As a means of improving the quality of our when you change the input to "BLUETOOTH".
products and services, Onkyo may collect "On": Use this function
information about your usage over the network. "Off": Do not use this function
Select "Yes" if you agree to our collecting this • This may not work with some BLUETOOTH
information. Select "No" if you do not want us to enabled devices.
collect this information.
• You can set this after confirming the Privacy
Policy. When you select "Usage Data" and
press ENTER, the Privacy Policy is displayed.
(The same screen is displayed once also when
setting up the network connection.) If you agree
to the collection of the information, this setting
also becomes "Yes". Note that if you agree
to the Privacy Policy but select "No" for this
setting, the information will not be collected.
Network Check ‐ You can check the network connection.
Press ENTER when "Start" is displayed.
18
Setting Item Default Value Setting Details ■ 4� Power Management

Pairing ‐ You can initialize the pairing information saved on
Information this unit. Setting Item Default Value Setting Details
Pressing ENTER when "Clear" is displayed Sleep Timer Off Allows the unit to enter standby automatically when
initializes the pairing information stored in this unit. the specified time elapses. Select a value from "30
• This function does not initialize the pairing minutes", "60 minutes", and "90 minutes".
information on the BLUETOOTH enabled "Off": Does not turn the unit to standby
device. When pairing the unit again with the automatically.
device, be sure to clear the pairing information Auto Standby On/Off This setting places the unit on standby
on the BLUETOOTH enabled device in automatically after 20 minutes of inactivity without
advance. For information on how to clear the any video or audio input. (When "USB Power
pairing information, refer to the BLUETOOTH Out at Standby" or "Network Standby" is on, this
enabled device's instruction manual. becomes the HYBRID STANDBY mode which
Device ‐ Displays the name of the BLUETOOTH enabled reduces the increase in power consumption to a
device connected to the unit. minimum.)
• The name is not displayed when "Status" is "On": The unit will automatically enter standby
"Ready" and "Pairing". mode ("AUTO STBY" will light).
"Off": The unit will not automatically enter standby
Status ‐ Displays the status of the BLUETOOTH enabled mode.
device connected to the unit. • "Auto Standby" is displayed on the display and
"Ready": Not paired TV screen 30 seconds before the Auto Standby
"Pairing": Paired comes on.
"Connected": Successfully connected • "Auto Standby" does not work when Zone 2 is
active.
• Wait for a while if "Bluetooth" cannot be selected. It will appear when the BLUETOOTH function is
• Default values vary depending on the regions.
started up.
Auto Standby in (Off) Enable or disable "Auto Standby" while "HDMI
HDMI Standby Standby Through" is on.
Through "On": The setting will be enabled.
"Off": The setting will be disabled.
• This setting cannot be set to "On" if "Auto
Standby" is set to "Off".
USB Power Out Off Devices connected to the USB port are supplied
at Standby with electricity even when this unit is in standby
mode when this function is "On".
• When using this feature, power consumption
increases even when the unit is on standby,
however, the increase in power consumption is
kept to a minimum by automatically entering the
HYBRID STANDBY mode, where only essential
circuits are operating.
19
Setting Item Default Value Setting Details 6� Multi Zone

Network Standby On When this feature is turned "On", you can turn
Make settings related to Multi-zone Connection, such as the volume for the separate room.
on the power of the unit via the network using an
application such as Onkyo Remote that can control
this unit. ■ 1� Zone 2
• When "Network Standby" is used, the power
consumption increases even when the unit Setting Item Default Value Setting Details
is on standby. However, the increase in
power consumption is kept to a minimum by Maximum Volume Off Set the maximum value for Zone 2 to avoid too
automatically entering the HYBRID STANDBY high volume. Select a value from "Off", "50" to "99".
mode, where only the essential circuit is Power On Volume Last Set the Zone 2 volume level of when this unit is
operating. turned on. Select a value from "Last" (Volume level
• "Network Standby", which suppresses power when the unit was turned off), "Min", "1" to "99" and
consumption, may be disabled when the "Max".
network connection is lost. Use the power • You cannot set a higher value than that of
button on the remote controller or main unit to "Maximum Volume".
turn the unit on if this happens.
Bluetooth Wakeup Off This function wakes up the unit on standby by
connecting a BLUETOOTH enabled device.
"Off": Do not use this function
• Setting to "On" increases the power
consumption even when the unit is on standby.
However, the increase in power consumption
is kept to a minimum by automatically entering
the HYBRID STANDBY mode, where only the
essential circuit is operating.
• This setting is fixed to "Off" if "Bluetooth" -
"Auto Input Change" is set to "Off".
• Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It will appear
when the network feature is started.
20
7� Miscellaneous ■ 3� Firmware Update
Change the frequency step for the tuner, update the firmware, and perform Initial Setup, Setting Item Default Value Setting Details
etc.
Update Notice Enable Availability of a firmware update will be notified via
network.
■ 1� Tuner "Enable": Notify updates
"Disable": Do not notify updates
Setting Item Default Value Setting Details Version ‐ The current firmware version will be displayed.
AM / FM 10 kHz / 0.2 MHz Select a frequency step depending on your area of Update via ‐ Press ENTER to select when you want to update
Frequency Step residence. NET the firmware via network.
(North American Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz". • You will not be able to select this setting if you
models) • When this setting is changed, all radio presets do not have Internet access or there is nothing
are deleted. to update.
AM Frequency 9 kHz Select a frequency step depending on your area of Update via ‐ Press ENTER to select when you want to update
Step (European, residence. USB the firmware via USB.
Australian and Select "10 kHz" or "9 kHz". • You will not be able to select this setting if a
Asian models) • When this setting is changed, all radio presets USB storage device is not connected or there is
are deleted. nothing to update in the USB storage device.
• Wait for a while if "Firmware Update" cannot be selected. It will appear when the network feature is
■ 2� Remote ID started.
Setting Item Default Value Setting Details ■ 4� Initial Setup

Remote ID 1 Select an ID for the unit's remote controller from You can make the initial setup from the setup menu.
"1", "2", and "3" to prevent interference between • Wait for a while if "Initial Setup" cannot be selected. It will appear when the network
the unit and other ONKYO components that are feature is started.
installed in the same room. After changing the ID
on the main unit, change the ID on the remote
controller accordingly with the following procedure. ■ 5� Lock
While holding down MODE, press the following Setting Item Default Value Setting Details
buttons for about 3 seconds. Setup Parameter Unlocked Lock the Setup menu to protect the settings.
• To change the remote controller ID to "1": "Locked": The menu is locked.
(The remote indicator flashes once.) "Unlocked": The menu is unlocked.
• To change the remote controller ID to "2":
(The remote indicator flashes twice.)

• To change the remote controller ID to "3":
(The remote indicator flashes three times.)
21
The speakers emit the test tone at high volume during 3. Test tones are emitted by the speakers, and firstly the
measurement, so be careful of your surroundings. Keep unit detects the speakers connected and the noise in
Initial Setup the room as quiet as possible during measurement. If the environment.
the measurement is interrupted, turn off the household 4. After the results of the above measurements are
appliances. displayed, select "Next", press ENTER on the remote
controller, and the test tones are emitted again, and the
1. Place the supplied speaker setup microphone in the
When you turn the unit on for the first time after purchasing unit automatically makes settings such as the optimum
listening position, and connect to the SETUP MIC jack
it, Initial Setup is automatically shown on the TV to enable volume level and the crossover frequency.
on the main unit.
you to make settings required for startup using simple 5. When the measurement is completed, the measurement
operations following onscreen guidance. result is displayed.
Press the cursors / on the remote controller to
Initial Setup check the settings. Press ENTER when "Save" is
Language Select
English
selected to save the settings.
Deutsch
Français
Español
AccuEQ Room Calibration
SETUP MIC
Italiano
Nederlands Review Crossover
Svenska Subwoofer : Yes
Front : 100Hz
Center : 100Hz
Exit Surround : 100Hz
Surround Back : ---
Height : 180Hz
Operation: Save
Cancel
Select the item with the cursors of the remote controller
and press ENTER to confirm your selection. To return to When putting the speaker setup microphone on a
the previous screen, press . tripod, refer to the illustration when putting it in place. 6. Select whether to enable or disable the equalizer
2. When the screen below is displayed, press ENTER function that corrects for distortion caused by the
To redo Initial Setup: acoustic environment of the room.
on the remote controller without changing any of the
If you terminate the procedure on the way or want to
settings.
change a setting made during Initial Setup, press on the
AccuEQ Room Calibration
remote controller, select "7. Miscellaneous" - "Initial Setup",
and press ENTER. AccuEQ Room Calibration To enable equalizer for each speakers, select "On".
Please select "All Channels", if you have same speakers for all
Speaker Channels 5.1.2 ch < > channels. Please select "Except Front Left / Right", if front
speakers are larger than other speakers.
Subwoofer Yes
■ 1� AccuEQ Room Calibration Height Speaker Bundled Dolby Speaker

Zone Speaker No On (All Channels)
Place the supplied speaker setup microphone in the Bi-Amp No

On (Except Front Left / Right)
Off
listening position, measure the test tones emitted by the Next
speakers, then the unit automatically sets the optimum Select how many speakers you have.
Next
volume level for each speaker, the crossover frequencies,
If this is to be enabled, then normally you should
and the distance from the listening position. This also
• If you have connected a subwoofer, check the power select "On (All Channels)", and to disable just the front
automatically adjusts the equalizers for the speakers and
and volume of the subwoofer. The low frequencies speakers you should select "On (Except Front Left /
enables correction of distortion caused by the acoustic
played by the subwoofer may not be discernible, so Right)".
environment of the room.
• Calibration takes several minutes to be completed. set its volume to at least halfway. 7. Disconnect the speaker setup microphone.
22
■ 2� Source Connection MEMORY on the remote controller. Pressing CLEAR will

delete all the input characters.
Check that each input source is connected correctly.
Follow the guidance, select the input you want to confirm, • A confirmation screen asking you to agree to the privacy
start play of the selected player, and confirm that the policy is displayed during network setting. Select "Yes"
images appear on the TV and that sound is played. and press ENTER to indicate agreement.
■ 3� Network Connection ■ 4� Multi Zone Setup

Set up Wi-Fi connection with an access point such as a Set the output method for audio to ZONE 2 when you want
wireless LAN router. There are the following two methods to output audio to enjoy in a separate room from the main
of connecting by Wi-Fi: room. If you have connected speakers in a separate room
"Scan Networks": Search for an access point from this with speaker cable, select "Using AV Receiver". If you
unit. Find out the SSID of the access point beforehand. have connected a pre-main amplifier in a separate room
"Use iOS Device (iOS7 or later)": Share the iOS device's with an analog audio cable, select "with External Premain
Wi-Fi settings with this unit. Amplifier".
If you select "Scan Networks", there are a further two
choices of connection method. Check the following. ■ 5� Audio Return Channel
"Enter Password": Enter the password (or key) of the
If you have connected a TV that supports ARC, select
access point to connect.
"Yes". This unit's ARC setting turns on and you can listen
"Push Button": If the access point has an automatic
to the TV's audio through this unit.
connection button, you can connect without entering a
• If you select "Yes", the HDMI CEC function is enabled
password.
and power consumption increases during standby.
• If the SSID of the access point is not displayed, then in
the screen listing the SSIDs, select "Other..." with the
cursor on the remote controller and press ENTER, then
follow the onscreen instructions.
Keyboard input
Wi-Fi Setup
SSID
a b c d e f g h i j k l m
n o p q r s t u v w x y z
1 2 3 4 5 6 7 8 9 0 - ^ \
, . / ; : @ [ ] ̺
A/a Ɵ ơ OK
When finished, select the "OK" key.
All Erase A/a
To switch between upper and lower case, select "A/a" on

the screen and press ENTER. To select whether to mask
the password with "＊" or display it in plain text, press
23
listening to some sound. sound of lossy compressed files such as MP3 will be
improved. The setting can be separately set to each input
Subwoofer:
Quick Menu Adjust the speaker level of the subwoofer while listening to
selector. The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream signals.
some sound.
• It cannot be set if the listening mode is Pure Audio
• The adjustment you made will be reset to the previous (European, Australian and Asian models) or Direct.
status when you turn the unit to standby mode.
You can quickly adjust settings you frequently use, such as Late Night:
tone adjustments, etc.
■ AccuEQ Make small sounds easily heard. It is useful when you
need to reduce the volume while watching a movie late
AccuEQ Room Calibration: night. You can enjoy the effect only when playing Dolby
Operation: Enable or disable the equalizer function that corrects for series and DTS series input signals.
You can make the settings on the TV screen while playing distortion caused by the acoustic environment of the room. • The setting cannot be used in the following cases.
something. Press Q on the remote controller to display the If this is to be enabled, then normally you should select – If "Loudness Management" is set to "Off" when
Quick Menu. "On (All Ch)", and to disable just the front speakers you playing Dolby Digital Plus or Dolby TrueHD
should select "On (ex. L/R)". The setting can be separately – When the input signal is DTS and "Dialog Control" is
Quick Menu BD/DVD set to each input selector. other than 0 dB
Tone Bass
Level Treble
Equalizer: Center Spread:
AccuEQ
Select "Preset 1" to "Preset 3" configured in "2. Speaker" - Adjust the width of the sound field of the front channel
Other
"Equalizer Settings" in the Setup menu. The same sound when playing in the Dolby Surround listening mode. To
field setting is applied all ranges when set to "Off". spread the width of the sound field to the left and right, set
Cinema Filter: to "On". To concentrate sound in the center, set to "Off".
Select the item with the cursor / buttons of the remote Adjust the soundtrack that was processed to enhance • Depending on the speaker settings, this becomes "Off".
controller and press ENTER to confirm your selection. its high pitch range, in order to make it suitable for home Dialog Control:
Use the cursors to change the settings. theater. This function can be used in the following listening You can increase the dialog portion of the audio in 1 dB
• To return to the previous screen, press . modes: Dolby Digital, Dolby Digital Plus, Dolby Surround, steps up to 6 dB so that you can make dialog easier to
• To exit the settings, press Q. Dolby TrueHD, Multichannel, DTS, DTS-ES, DTS 96/24, hear over background noise.
DTS-HD High Resolution Audio, DTS-HD Master Audio, • This cannot be set for content other than DTS:X.
DTS Neural:X, DTS Express, Neo:6 Cinema, and DSD.
■ Tone • We plan to provide support for the DTS:X audio format
• It cannot be set if the listening mode is Pure Audio through a firmware update for this unit. Center Image is
Bass:
(European, Australian and Asian models) or Direct. displayed until the update.
Enhance or moderate the bass range of the front speakers.
• The effect may not be selectable with some content.
Treble: ■ Other HDMI Out:
Enhance or moderate the treble range of the front
A/V Sync : Allows you to select the HDMI jack to output video signals
speakers.
If the video is behind the audio, you can delay the audio to from "MAIN", "SUB", and "MAIN+SUB".
• It cannot be set if the listening mode is Pure Audio offset the gap. Different settings can be set for each input
(European, Australian and Asian models) or Direct. selector.
• It cannot be set if the listening mode is Pure Audio
■ Level (European, Australian and Asian models) or Direct.
Center: Music Optimizer:
Adjust the speaker level of the center speaker while Improve the quality of the compressed audio. Playback
24
Connections for Different Height Speakers Types 1. Connect the and speakers as shown below
using the FRONT terminals and SURROUND BACK or
Advanced Speaker Connections ■ Front High HEIGHT terminals.
Install the Front speakers and Front High

speakers as shown in the figure to enjoy the Dolby Atmos
listening mode. Install the Front High speakers on the
The Basic Manual explains how to connect a 5.1.2 upper part of the front wall.
channel system using the included speakers. Different
connection methods are introduced here.
Audio output is set to match the included speaker
configuration by default. Change the speaker configuration
to suit the number of speakers connected and the method
of connection.
• Connect speakers with 6 Ω to 16 Ω impedance. Using
a speaker with less impedance than the supported
value may result in failure.
2. Change the setting on the screen of "2. Speaker" -

"Configuration" in the Setup menu.
25
■ Top Front 1. Connect the and speakers as shown below ■ Top Middle
Install the Front speakers and Top Front Install the Front speakers and Top Middle
HEIGHT terminals.
speakers as shown in the figure to enjoy the Dolby Atmos speakers as shown in the figure to enjoy the Dolby
listening mode. Install Ceiling Speakers or such other Atmos listening mode. Install Ceiling Speakers or such
speakers as Top Front speakers so that they are positioned other speakers as Top Middle speakers so that they are
around the middle of just above the listening position and positioned just above the listening position.
just above the front speakers.

26
1. Connect the and speakers as shown below ■ Top Rear 1. Connect the and speakers as shown below
using the FRONT terminals and SURROUND BACK or using the FRONT terminals and SURROUND BACK or
Install the Front speakers and Top Rear
HEIGHT terminals. HEIGHT terminals.
speakers as shown in the figure to enjoy the Dolby Atmos
listening mode. Install Ceiling Speakers or such other
speakers as Top Rear speakers so that they are positioned
around the middle of just above the listening position and
just above the surround back speakers.
2. Change the setting on the screen of "2. Speaker" - 2. Change the setting on the screen of "2. Speaker" -
"Configuration" in the Setup menu. "Configuration" in the Setup menu.
27
■ Rear High 1. Connect the and speakers as shown below ■ Dolby Enabled Speaker (Front)
Install the Front speakers and Rear High Install the Front speakers and Dolby Enabled
HEIGHT terminals.
speakers as shown in the figure to enjoy the Dolby Atmos Speakers (Front) as shown in the figure to enjoy the
listening mode. Install the Rear High speakers on the Dolby Atmos listening mode. Dolby Enabled Speakers are
upper part of the back wall. Height speakers and installed on the top board of the front
speakers.

28
1. Connect the and speakers as shown below ■ Dolby Enabled Speaker (Surround) 1. Connect the and speakers as shown below
using the FRONT terminals and SURROUND BACK or using the FRONT terminals and SURROUND BACK or
Install the Front speakers and Dolby Enabled
HEIGHT terminals. HEIGHT terminals.
Speakers (Surround) as shown in the figure to enjoy the
Dolby Atmos listening mode. Dolby Enabled Speakers
are Height speakers and installed on the top board of the
surround speakers.
2. Change the setting on the screen of "2. Speaker" - 2. Change the setting on the screen of "2. Speaker" -
"Configuration" in the Setup menu. "Configuration" in the Setup menu.
29
Surround back Speakers Connection 1. Connect the and speakers as shown below Front Speakers Bi-amp Connection
Install the Front speakers on the front and HEIGHT terminals. It is possible to connect front speakers supporting biamping
Surround back speakers on the back as shown in the to improve quality of the bass and treble. The maximum
figure. number of channels available with this connection is 5.1
because Bi-Amping speakers require one amplifier for the
tweeter jacks and one amplifier for the woofer jacks. The
effects and placements for speakers are the same as the
5.1-channel plan that doesn't use Bi-Amping speakers.
• If you connect to speakers supporting Bi-Amping,
speaker output in ZONE is not possible.
1. Connect front speakers compatible with Bi-Amping connection to

the FRONT jacks and the SURROUND BACK or HEIGHT jacks.
Make sure you remove the jumper bar fitted between the woofer
jacks and tweeter jacks of the front speakers. In case of Bi-Amping
connection, refer to the instruction manual of your speakers.
2. In the Setup menu, set "2. Speaker" - "Configuration" -

"Speaker Channels" to "6.1 ch" or "7.1 ch".
For high-frequency
For low-frequency

30
online documentation, regardless of legal theory, and Updating the Firmware via Network
whether arising in tort or contract.
Firmware Update In no event will our company be liable to you or any third Preparation:
party for any special, indirect, incidental, or consequential • Check that the unit is turned on, and the connection to
damages of any kind, including, but not limited to, the Internet is secured.
compensation, reimbursement or damages on account of • Turn off the controller component (PC etc.) connected
About Firmware Update the loss of present or prospective profits, loss of data, or to the network.
for any other reason whatsoever. • Stop any playing Internet radio, USB storage device, or
There are two methods for updating the firmware: via server content.
network and via USB. • If the multi-zone function is active, turn it off.
Use the one that best suits your environment. • If "HDMI CEC" is set to "On", set it to "Off".
• For the latest information on updates, visit our – Press on the remote controller. Then, after
company's website. There is no need to update the selecting "5. Hardware" - "HDMI" and pressing
firmware on this unit if there is no update available. ENTER, select "HDMI CEC" and select "Off".
＊ The description may differ from the on-screen display but that will not
• Before updating, make sure that the speaker setup change the way to operate or the function.
microphone is not connected.
• During an update, do not
– Disconnect and reconnect any cable, USB storage ■ Update
device, speaker setup microphone or headphones, 1. Press on the remote controller.
or perform any operation on the component such as The Setup menu is displayed on the TV screen.
turn off its power
– Accessing this unit from a PC or smartphone using
Setup
an application
• The update may take about 20 minutes to complete for 1. Input/Output Assign 1. TV Out / OSD

either method: via network or via USB. Furthermore, 3. Audio Adjust 3. Video Input
existing settings are guaranteed regardless of the 4. Source 4. Digital Audio Input
method used for update. 5. Hardware 5. Analog Audio Input
Note that when this unit is connected to a network, you

6. Multi Zone
7. Miscellaneous
may see notifications about firmware updates on the
display. To execute updating, select "Update Now" with the
cursor buttons of the remote controller and press ENTER.
2. Select "7. Miscellaneous" - "Firmware Update" -
The unit automatically turns itself into standby mode after
"Update via NET" with the cursors in order, then press
"Completed!" appears on the display, and updating will be
ENTER.
complete.
Disclaimer: The program and accompanying online

documentation are furnished to you for use at your own
risk.
Our company will not be liable and you will have no
remedy for damages for any claim of any kind whatsoever
concerning your use of the program or the accompanying
31
Error Code Updating via USB

Setup • ＊-01, ＊-10：
1. Input/Output Assign 1. Tuner
Ethernet cable not found. Connect the Ethernet cable Preparation:
2. Speaker 2. Remote ID properly. • Prepare a 128MB or larger USB storage device. FAT16
3. Audio Adjust 3. Firmware Update • ＊-02, ＊-03, ＊-04, ＊-05, ＊-06, ＊-11, ＊-13, ＊-14, ＊ or FAT32 file system format.
4. Source 4. Initial Setup
-16, ＊-17, ＊-18, ＊-20, ＊-21： – Media inserted in a USB card reader may not be
5. Hardware 5. Lock
6. Multi Zone
Internet connection error. Check the following: used for this function.
7. Miscellaneous – The router is turned on – USB storage devices with security function are not
– This unit and the router are connected via the supported.
network – USB hubs and USB devices with hub function are
• If "Firmware Update" is grayed out and cannot be Try to disconnect and then connect again the power not supported. Do not connect these devices to the
selected, wait for a while until it starts up. to the unit and router. This may solve the problem. If unit.
• You will not be able to select "Update via NET" if you are still unable to connect to the Internet, the DNS • Delete any data stored on the USB storage device.
there is nothing to update. server or proxy server may be temporarily down. Check • Turn off the controller component (PC etc.) connected
the service status with your ISP provider. to the network.
3. Press ENTER with "Update" selected to start update. • Others • Stop any playing Internet radio, USB storage device, or
• During the update, the TV screen may go black Disconnect then reconnect the AC power cord, then server content.
depending on the updated program. In that case, repeat from the beginning. • If the multi-zone function is active, turn it off.
check the progress on the display of the unit. The
• If "HDMI CEC" is set to "On", set it to "Off".
TV screen will remain black until the update is
– Press on the remote controller. Then, after
complete and the power is turned on again.
selecting "5. Hardware" - "HDMI" and pressing
• "Completed!" is displayed when the update is
ENTER, select "HDMI CEC" and select "Off".
complete. ＊ Some USB storage devices may take long to load, may not be loaded
correctly, or may not be correctly fed depending on the device or their
4. Press ON/STANDBY on the main unit to turn the unit
content.
into standby mode. The process is completed and your ＊ Our company will not be liable whatsoever for any loss or damage of
firmware is updated to the latest version. data, or storage failure arising from the use of the USB storage device
• Do not use on the remote controller. with this unit. Thank you for your understanding.
＊ The description may differ from the on-screen display but that will not
change the way to operate or the function.
■ Update
1. Connect the USB storage device to your PC.
2. Download the firmware file from our company's website
to your PC and unzip.
Firmware files are named in the following way:
ONKAVR＊＊＊＊_＊＊＊＊＊＊＊＊＊＊＊＊.zip
Unzip the file on your PC. The number of unzipped files
■ If an Error Message is Displayed
and folders varies depending on the model.
When an error occurs, "＊-＊＊ Error!" is displayed on
3. Copy all unzipped files and folders to the root folder of
the display of the unit. ("＊" represents an alphanumeric
the USB storage device.
character.) Check the following:
• Make sure to copy the unzipped files.
32
4. Connect the USB storage device to the USB port of the TV screen will remain black until the update is
unit. complete and the power is turned on again.
• If you connect a USB hard disk drive to the USB • During the update, do not turn off, or disconnect
port of the unit, we recommend that you use its AC then reconnect the USB storage device.
adapter to power it. • "Completed!" is displayed when the update is
• If the USB storage device has been partitioned, complete.
each section will be treated as an independent
8. Disconnect the USB storage device from the unit.
device.
9. Press ON/STANDBY on the main unit to turn the unit
5. Press on the remote controller. into standby mode. The process is completed and your
The Setup menu is displayed on the TV screen. firmware is updated to the latest version.
• Do not use on the remote controller.
Setup
1. Input/Output Assign 1. TV Out / OSD
3. Audio Adjust 3. Video Input
4. Source 4. Digital Audio Input
5. Hardware 5. Analog Audio Input
6. Multi Zone
7. Miscellaneous
6. Select "7. Miscellaneous" - "Firmware Update" -

"Update via USB" with the cursors in order, then press ■ If an Error Message is Displayed
ENTER.
When an error occurs, "＊-＊＊ Error!" is displayed on
the display of the unit. ("＊" represents an alphanumeric
Setup
character.) Check the following:
1. Input/Output Assign 1. Tuner
2. Speaker 2. Remote ID Error Code

3. Audio Adjust 3. Firmware Update
• ＊-01, ＊-10：
4. Source 4. Initial Setup
5. Hardware 5. Lock
USB storage device not found. Check whether the USB
6. Multi Zone storage device or USB cable is correctly inserted to the
7. Miscellaneous USB port of the unit.
Connect the USB storage device to an external power
source if it has its own power supply.
• If "Firmware Update" is grayed out and cannot be • ＊-05, ＊-13, ＊-20, ＊-21：
selected, wait for a while until it starts up. The firmware file is not present in the root folder of the
• You will not be able to select "Update via USB" if USB storage device, or the firmware file is for another
there is nothing to update. model. Retry from the download of the firmware file.
• Others
7. Press ENTER with "Update" selected to start update.
• During the update, the TV screen may go black Disconnect then reconnect the AC power cord, then
repeat from the beginning.
depending on the updated program. In that case,
check the progress on the display of the unit. The
33
Selecting Listening Modes
Select the optimum listening mode for movies, TV, music,

and games by repeatedly pressing the MOVIE/TV, MUSIC,
and GAME buttons.
1. During play, press one of the following three buttons on

the remote controller.
• Selecting the Pure Audio listening mode turns off the
analog video circuitry, so the video signals input through
the jacks other than the HDMI input jack cannot be
displayed on the TV.
2. Press the selected button repeatedly to switch the

modes displayed on the display of the unit.
For details on the effects of each of the listening modes

see "Listening Mode Effects". For listening modes
selectable for each of the audio formats in the input
signals, refer to "Selectable Listening Modes".
When you press PURE AUDIO on the front of the unit

(European, Australian and Asian models), the display and
analog video circuits are turned off, and the unit switches
to the Pure Audio listening mode to provide purer sound.
Selecting this mode lights the PURE AUDIO indicator on
the unit. Pressing the button again reselects the previous
listening mode.
34
placement of sound objects that have independent is 2 channels or 5.1 channels. Dolby surround is a next
motion in a three-dimensional space with even greater generation surround technology that intelligently up mixes
Listening Mode Effects clarity. Dolby Atmos is an optional audio format on Blu- stereo; 5.1 and 7.1 content for playback through your
ray Discs and achieves a three-dimensional sound field by surround speaker system. Dolby surround is compatible
introducing a sound field above the listener. with traditional speaker layouts, as well as Dolby Atmos
• To enable transfer of this audio format, connect via enabled playback systems that employ inceiling speakers
■ Updating of listening modes HDMI cable and set audio output on the player to or products with Dolby speaker technology.
bitstream output.
We plan to provide support for the DTS:X audio format ■ Dolby TrueHD
through firmware updates for this unit. This means that ■ Dolby D (Dolby Digital) This mode faithfully reproduces the sound design recorded
the selectable listening modes depend on the version of
This mode faithfully reproduces the sound design recorded in the Dolby TrueHD audio format.
firmware.
in the Dolby Digital audio format. The Dolby TrueHD audio format is a reversible format
On firmware version before DTS:X support Dolby Digital is a multi-channel digital format developed expanded based on the lossless compression technology
• You can select Neo:6 Cinema and Neo:6 Music. by Dolby Laboratories, Inc. widely adopted for use in referred to as MLP, and it makes it possible to faithfully
movie production. It is also a standard audio format on reproduce the master audio recorded in the studio. Dolby
On firmware version after DTS:X support
DVD-Video and Blu-ray Discs. It is possible to record a TrueHD is used as an optional audio format on Blu-ray
• You can select DTS:X and DTS Neural:X. (You cannot
maximum of 5.1 channels on a DVD-Video or Blu-ray Discs, based on 5.1ch, but with additional channels such
select Neo:6 Cinema and Neo:6 Music after updating.)
Disc; two front channels, a center channel, two surround as the surround back channel added for a maximum of
channels, and the LFE channel dedicated to the bass 7.1ch. 7.1ch is recorded at 96 kHz/24bit, and 5.1ch is
In alphabetical order region (sound elements for the subwoofer). recorded at 192 kHz/24bit.
• To enable transfer of this audio format, connect via • To enable transfer of this audio format, connect via
■ AllCh Stereo HDMI cable and set audio output on the player to
digital cable and set audio output on the player to
Ideal for background music, this mode fills the entire bitstream output. bitstream output.
listening area with stereo sound from the front, surround,
and surround back speakers. ■ Dolby D＋ (Dolby Digital Plus) ■ DSD
This mode faithfully reproduces the sound design recorded Mode suitable for playing sources recorded in DSD.
■ Direct
in the Dolby Digital Plus audio format. • This unit supports DSD signals input through HDMI IN.
This listening mode can be selected for all input signals. The Dolby Digital Plus format is a revision based on However, depending on the connected player, better
Processing that affects sound quality is shut down so Dolby Digital, increasing the number of channels and sound is possible when output from the PCM output of
sound closer to the original is reproduced. Speakers play endeavoring to improve sound quality by giving more the player.
the sound field according to the number of channels in the flexibility in data bit rates. Dolby Digital Plus is used as an • This listening mode cannot be selected if the output
input signal, so there would be output from only the front optional audio format on Blu-ray Discs, based on 5.1ch, setting on your Blu-ray Disc/DVD player is not set to
speakers for a two-channel signal, for example. but with additional channels such as the surround back DSD.
channel added for a maximum of 7.1ch.
■ Dolby Atmos • To enable transfer of this audio format, connect via ■ DTS
This mode faithfully reproduces the sound design recorded HDMI cable and set audio output on the player to This mode faithfully reproduces the sound design recorded
in the Dolby Atmos audio format. bitstream output. in the DTS audio format.
The Dolby Atmos audio format has been implemented The DTS audio format is a multi-channel digital format
in movie theaters equipped with the latest facilities and ■ Dolby Surround developed by DTS, Inc. This format is an optional audio
enables a revolutionary sound experience in home These listening modes allow you to expand the playback format on DVD-Video and a standard on Blu-ray Discs.
theaters. Unlike existing surround systems, Dolby Atmos signal to 5.1 channels or 7.1 channels to suit the It enables recording of 5.1 channels; two front channels,
doesn't rely on channels, but rather enables the accurate connected speaker configuration when the input signal a center channel, two surround channels, and the LFE
35
channel dedicated to the bass region (sound elements HDMI cable and set audio output on the player to and the ability to express movement. DTS:X is DTS's
for the subwoofer). The content is recorded with a rich bitstream output. next-generation object-based surround sound technology
volume of data, with maximum sampling rate of 48 kHz at that includes height to deliver a fully-immersive listening
a resolution of 24 bits and a bit rate of 1.5 Mbps. ■ DTS-HD MSTR (DTS-HD Master Audio) experience to your living room.
• To enable transfer of this audio format, connect via This mode faithfully reproduces the sound design recorded • To enable transfer of this audio format, connect via
digital cable and set audio output on the player to in the DTS-HD Master Audio audio format. HDMI cable and set audio output on the player to
bitstream output. DTS-HD Master Audio is used as an optional audio format bitstream output.
on Blu-ray Discs, based on 5.1ch, but with additional
■ DTS 96/24 channels such as the surround back channel added ■ ES Discrete (DTS-ES Discrete)
This mode faithfully reproduces the sound design recorded for a maximum of 7.1ch, recorded using lossless audio This mode faithfully reproduces the sound design recorded
in the DTS 96/24 audio format. reproduction technology. 96 kHz/24bit is supported with in the DTS-ES Discrete audio format.
The DTS 96/24 format is an optional audio format on 7.1ch, and 192 kHz/24bit is supported with 5.1ch. DTS-ES Discrete is used as an optional audio format on
DVD-Video and Blu-ray Discs. It enables recording of • To enable transfer of this audio format, connect via DVD-Video and Blu-ray Discs, based on 5.1ch, but with
5.1 channels; two front channels, a center channel, two HDMI cable and set audio output on the player to an additional monaural surround back channel added for a
surround channels, and the LFE channel dedicated to the bitstream output. maximum of 6.1ch.
bass region (sound elements for the subwoofer). Detailed • To enable transfer of this audio format, connect via
reproduction is achieved by recording the content at a ■ DTS Neo:6 digital cable and set audio output on the player to
sampling rate of 96 kHz at a resolution of 24 bits. These listening modes allow you to expand the playback bitstream output.
• To enable transfer of this audio format, connect via signal to 5.1 channels or 7.1 channels to suit the
digital cable and set audio output on the player to connected speaker configuration when the input signal ■ ES Matrix (DTS-ES Matrix)
bitstream output. is 2 channel. It offers full-bandwidth on all channels, with This mode faithfully reproduces the sound design recorded
great independence between the channels. There are two in the DTS-ES Matrix audio format.
■ DTS Express variants for this mode: Neo:6 Cinema which is ideal for DTS-ES Matrix is used as an optional audio format on
This mode faithfully reproduces the sound design recorded movies and Neo:6 Music which is ideal for music. DVD-Video and Blu-ray Discs, based on 5.1ch, but with
in the DTS Express audio format. a monaural surround back channel included by matrix
DTS Express is used as an optional audio format on Blu- ■ DTS Neural:X encoding. The matrix decoder on this unit decodes this
ray Discs, based on 5.1ch, but with channels such as the This listening mode allows you to expand the playback during playback to produce 6.1 channels.
surround back channel added for a maximum of 7.1ch. It signal to 5.1 channels or 7.1 channels to suit the • To enable transfer of this audio format, connect via
also supports low bit rates. connected speaker configuration when the input signal is digital cable and set audio output on the player to
• To enable transfer of this audio format, connect via 2 channels or 5.1 channels. Neural:X enables upmixing of bitstream output.
HDMI cable and set audio output on the player to legacy content such as mono, stereo, 5.1 or 7.1ch to many
bitstream output. higher speaker count including the layout using elevated ■ Full Mono
channels set for DTS:X playback. In this mode, all speakers output the same sound in mono,
■ DTS-HD HR (DTS-HD High Resolution Audio) so the sound you hear is the same regardless of where
This mode faithfully reproduces the sound design recorded ■ DTS:X you are within the listening room.
in the DTS-HD High Resolution Audio audio format. This mode faithfully reproduces the sound design recorded
DTS-HD High Resolution Audio is used as an optional in the DTS:X audio format. ■ Game-Action
audio format on Blu-ray Discs, based on 5.1ch, but with The DTS:X audio format is a combination of the mixing In this mode, sound localization is distinct with emphasis
additional channels such as the surround back channel methodology based on past channel based formats (5.1ch on bass.
added for a maximum of 7.1ch. It can be recorded at a and 7.1ch) and object based dynamic audio mixing, and
sampling rate of 96 kHz with a resolution of 24 bits. it is characterized by the precise positioning of sounds ■ Game-Rock
• To enable transfer of this audio format, connect via
36
In this mode, sound pressure is emphasized to heighten In this mode, sound is output from the front left and right
live feel. speakers and subwoofer.
■ Game-RPG ■ Studio-Mix
In this mode, the sound has a dramatic feel with a similar Suitable for rock or pop music. Listening to music in this
atmosphere to Orchestra mode. mode creates a lively sound field with a powerful acoustic
image, like being at a club or rock concert.
■ Game-Sports
Suitable for audio source with much reverberation. ■ T-D (Theater-Dimensional)
In this mode, you can enjoy a virtual playback of
■ Mono multichannel surround sound even with only two or three
Use this mode when watching an old movie with a mono speakers. This works by controlling how sounds reach the
soundtrack, or use it to separately reproduce soundtracks listener's left and right ears.
in two different languages recorded in the left and right
channels of some movies. It is also suitable for DVDs or ■ TV Logic
other sources containing multiplexed audio. Suitable for TV shows produced in a TV studio. This mode
enhances the surround effects to the entire sound to give
■ Multich (Multichannel) clarity to voices and create a realistic acoustic image.
Mode suitable for playing sources recorded in multichannel
PCM. ■ Unplugged
Suitable for acoustic instruments, vocals and jazz. This
■ Orchestra mode emphasizes the front stereo image, giving the
Suitable for classical or operatic music. This mode impression of being right in front of the stage.
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of a
large hall.
■ Pure Audio (European, Australian and Asian

models)
This mode reproduces the original sound more faithfully.
The display and analog video circuit are turned off to
provide purer sound.
• Selecting this mode turns off the analog video circuitry,
so the video signals input through the jacks other than
the HDMI input jack cannot be displayed on the TV.
• This cannot be selected when using the Multi-zone
feature. Activating the Multi-zone feature while this
mode is selected automatically switches the listening
mode to Direct.
■ Stereo
37
■ MOVIE/TV button Input Format Listening Mode

This is a list of listening modes you can select according to Multich PCM Direct
Selectable Listening Modes the audio format of the input signal.
Multich
1
Input Format Listening Mode Dolby Surround

Analog Direct DTS Neural:X
You can select a variety of listening modes to suit the audio
TV Logic
2
format of the signal being input. Refer to the following for Mono
the listening mode choices. Dolby Surround AllCh Stereo
3
• Listening modes available when headphones are

Full Mono
3
Neo:6 Cinema
1
connected are: Pure Audio (European, Australian and
Asian models), Mono, Direct, and Stereo. DTS Neural:X T-D
TV Logic
2 1 A center speaker or surround speakers need to be installed.
■ Updating of listening modes 2 Surround speakers or height speakers need to be installed.
AllCh Stereo
3 3 A center speaker, surround speakers, or height speakers need to be
We plan to provide support for the DTS:X audio format installed.
Full Mono
3
through firmware updates for this unit. This means that Input Format Listening Mode
the selectable listening modes depend on the version of T-D
firmware. DSD Direct
1 A center speaker or surround speakers need to be installed.
DSD
1 2
Surround speakers or height speakers need to be installed.
On firmware version before DTS:X support
2
3 A center speaker, surround speakers, or height speakers need to be

• You can select Neo:6 Cinema and Neo:6 Music. installed. Dolby Surround
Neo:6 Cinema
3
On firmware version after DTS:X support Input Format Listening Mode
• You can select DTS:X and DTS Neural:X. (You cannot PCM Direct DTS Neural:X
select Neo:6 Cinema and Neo:6 Music after updating.) Music files (except DSD/ TV Logic
4
Mono
Dolby TrueHD)
AllCh Stereo
5
Dolby Surround
Full Mono
5
Neo:6 Cinema
1
DTS Neural:X T-D

TV Logic
2 1 Cannot be selected when the input format is monaural or 2 ch.
AllCh Stereo
3 3 Can only be selected when the input format is 2 ch and a center speaker
or surround speakers are installed.
Full Mono
3 4 Surround speakers or height speakers need to be installed.
T-D installed.
2 Surround speakers or height speakers need to be installed.
installed.
38
Input Format Listening Mode Input Format Listening Mode Input Format Listening Mode
Dolby Atmos Direct Dolby D+ Direct DTS Direct
• You can select the Dolby Atmos Dolby D+
1 2
DTS
1 2
Dolby Digital Plus or

Dolby TrueHD listening TV Logic Dolby Surround Dolby Surround
modes if a surround AllCh Stereo Neo:6 Cinema
3
Neo:6 Cinema
3
back speaker or
Full Mono DTS Neural:X DTS Neural:X
height speaker is not
T-D TV Logic TV Logic
4 4
connected.
AllCh Stereo AllCh Stereo
5 5
Input Format Listening Mode
Full Mono Full Mono
5 5
Dolby D Direct
Dolby D
1 2
T-D T-D
Cannot be selected when the input format is 2 ch. Cannot be selected when the input format is 2 ch.
Dolby Surround
1 1
2 A center speaker or surround speakers need to be installed. 2 A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center speaker Can only be selected when the input format is 2 ch and a center speaker
Neo:6 Cinema
3 3 3
or surround speakers are installed. or surround speakers are installed.

Surround speakers or height speakers need to be installed. Surround speakers or height speakers need to be installed.
DTS Neural:X
4 4
5 A center speaker, surround speakers, or height speakers need to be 5 A center speaker, surround speakers, or height speakers need to be
TV Logic
4 installed. installed.
AllCh Stereo
5 Input Format Listening Mode Input Format Listening Mode
Full Mono
5 Dolby TrueHD Direct DTS 96/24 Direct
Dolby TrueHD DTS 96/24
1 2 1 2
T-D
1 Cannot be selected when the input format is 2 ch. Dolby Surround Dolby Surround
Neo:6 Cinema Neo:6 Cinema
3 3
3 Can only be selected when the input format is 2 ch and a center speaker
or surround speakers are installed.
4 Surround speakers or height speakers need to be installed. DTS Neural:X DTS Neural:X
TV Logic TV Logic
4 4
installed.
5 5
Full Mono Full Mono

5 5
T-D T-D
1 Cannot be selected when the input format is 2 ch. 1 Cannot be selected when the input format is 2 ch.
3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker
4 Surround speakers or height speakers need to be installed. 4 Surround speakers or height speakers need to be installed.
installed. installed.
39
DTS Express Direct DTS-HD MSTR Direct DTS:X Direct
DTS Express DTS-HD MSTR DTS:X
1 2 1 2
Dolby Surround Dolby Surround TV Logic

1
Neo:6 Cinema Neo:6 Cinema AllCh Stereo

3 3 2
DTS Neural:X DTS Neural:X Full Mono

2
TV Logic TV Logic T-D

4 4

5 5 1 Surround speakers or height speakers need to be installed.
Full Mono Full Mono
5 5
installed.
T-D T-D
3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker
4 Surround speakers or height speakers need to be installed. 4 Surround speakers or height speakers need to be installed.
installed. installed.
Input Format Listening Mode Input Format Listening Mode

DTS-HD HR Direct DTS-ES Direct
DTS-HD HR DTS
1 2 1
Dolby Surround ES Matrix

2
Neo:6 Cinema ES Discrete

3 2
DTS Neural:X Dolby Surround

3
TV Logic DTS Neural:X

4
AllCh Stereo TV Logic

5 4
Full Mono AllCh Stereo

5 5
T-D Full Mono

5
1 Cannot be selected when the input format is 2 ch. T-D

3 Can only be selected when the input format is 2 ch and a center speaker 1 This can only be selected when no surround back speaker is connected.
or surround speakers are installed. 2 Surround back speakers need to be installed.
4 Surround speakers or height speakers need to be installed. 3 Height speakers need to be installed.
5 A center speaker, surround speakers, or height speakers need to be 4 Surround speakers or height speakers need to be installed.
installed. 5 A center speaker, surround speakers, or height speakers need to be
installed.
40
■ MUSIC button Input Format Listening Mode Input Format Listening Mode
This is a list of listening modes you can select according to PCM Pure Audio (European, DSD Pure Audio (European,
the audio format of the input signal. Music files (except DSD/ Australian and Asian models) Australian and Asian models)
Dolby TrueHD) Direct Direct
Analog Pure Audio (European, Stereo Stereo
Dolby Surround DSD
1 2
Australian and Asian models)
Neo:6 Music Dolby Surround
1
Direct
DTS Neural:X Neo:6 Music
3
Stereo
Orchestra DTS Neural:X
2
Dolby Surround
Unplugged Orchestra
2 4
Neo:6 Music
1
Studio-Mix Unplugged
2 4
DTS Neural:X
AllCh Stereo Studio-Mix
3 4
Orchestra
2
Full Mono AllCh Stereo

3 5
Unplugged
2
Full Mono
5
Studio-Mix
2 1 A center speaker or surround speakers need to be installed.
AllCh Stereo
3 3 A center speaker, surround speakers, or height speakers need to be 1 Cannot be selected when the input format is monaural or 2 ch.
installed. 2 A center speaker or surround speakers need to be installed.
Full Mono
3 3 Can only be selected when the input format is 2 ch and a center speaker
Input Format Listening Mode or surround speakers are installed.
1 A center speaker or surround speakers need to be installed. 4 Surround speakers or height speakers need to be installed.
2 Surround speakers or height speakers need to be installed. Multich PCM Pure Audio (European, 5 A center speaker, surround speakers, or height speakers need to be
A center speaker, surround speakers, or height speakers need to be installed.
3
installed.
Direct Input Format Listening Mode
Stereo Dolby Atmos Pure Audio (European,

• You can select the Australian and Asian models)
Multich
1
Dolby Digital Plus or Direct
Dolby Surround Dolby TrueHD listening
modes if a surround Stereo
DTS Neural:X
back speaker or Dolby Atmos
Orchestra
2
Orchestra
Unplugged
2
connected.
Unplugged
Studio-Mix
2
Studio-Mix
AllCh Stereo
3
AllCh Stereo
Full Mono
3
Full Mono
installed.
41
Dolby D Pure Audio (European, Dolby D+ Pure Audio (European, Dolby TrueHD Pure Audio (European,
Australian and Asian models) Australian and Asian models) Australian and Asian models)
Direct Direct Direct
Stereo Stereo Stereo
Dolby D Dolby D+ Dolby TrueHD
1 2 1 2 1 2
Dolby Surround Dolby Surround Dolby Surround

Neo:6 Music Neo:6 Music Neo:6 Music
3 3 3
DTS Neural:X DTS Neural:X DTS Neural:X

Orchestra Orchestra Orchestra
4 4 4
Unplugged Unplugged Unplugged

4 4 4
Studio-Mix Studio-Mix Studio-Mix

4 4 4
AllCh Stereo AllCh Stereo AllCh Stereo

5 5 5
Full Mono Full Mono Full Mono

5 5 5
1 Cannot be selected when the input format is 2 ch. 1 Cannot be selected when the input format is 2 ch. 1 Cannot be selected when the input format is 2 ch.
2 A center speaker or surround speakers need to be installed. 2 A center speaker or surround speakers need to be installed. 2 A center speaker or surround speakers need to be installed.
3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker
or surround speakers are installed. or surround speakers are installed. or surround speakers are installed.
4 Surround speakers or height speakers need to be installed. 4 Surround speakers or height speakers need to be installed. 4 Surround speakers or height speakers need to be installed.
5 A center speaker, surround speakers, or height speakers need to be 5 A center speaker, surround speakers, or height speakers need to be 5 A center speaker, surround speakers, or height speakers need to be
installed. installed. installed.
42
DTS Pure Audio (European, DTS 96/24 Pure Audio (European, DTS Express Pure Audio (European,
DTS DTS 96/24 DTS Express
1 2 1 2 1 2

Neo:6 Music Neo:6 Music Neo:6 Music
3 3 3

Orchestra Orchestra Orchestra
4 4 4
Unplugged Unplugged Unplugged

4 4 4
Studio-Mix Studio-Mix Studio-Mix

4 4 4

5 5 5

5 5 5
3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker
or surround speakers are installed. or surround speakers are installed. or surround speakers are installed.
43
DTS-HD HR Pure Audio (European, DTS-HD MSTR Pure Audio (European, DTS-ES Pure Audio (European,
DTS-HD HR DTS-HD MSTR DTS
1 2 1 2 1
Dolby Surround Dolby Surround ES Matrix

2
Neo:6 Music Neo:6 Music ES Discrete

3 3 2
DTS Neural:X DTS Neural:X Dolby Surround

3
Orchestra Orchestra DTS Neural:X

4 4
Unplugged Unplugged Orchestra

4 4 4
Studio-Mix Studio-Mix Unplugged

4 4 4
AllCh Stereo AllCh Stereo Studio-Mix

5 5 4
Full Mono Full Mono AllCh Stereo

5 5 5
Full Mono
5
3 Can only be selected when the input format is 2 ch and a center speaker 3 Can only be selected when the input format is 2 ch and a center speaker 1 This can only be selected when no surround back speaker is connected.
or surround speakers are installed. or surround speakers are installed. 2 Surround back speakers need to be installed.
4 Surround speakers or height speakers need to be installed. 4 Surround speakers or height speakers need to be installed. 3 Height speakers need to be installed.
5 A center speaker, surround speakers, or height speakers need to be 5 A center speaker, surround speakers, or height speakers need to be 4 Surround speakers or height speakers need to be installed.
installed. installed. 5 A center speaker, surround speakers, or height speakers need to be
installed.

DTS:X Pure Audio (European,
Direct
Stereo
DTS:X
Orchestra
1
Unplugged
1
Studio-Mix
1
AllCh Stereo
2
Full Mono
2

installed.
44
■ GAME button Input Format Listening Mode Input Format Listening Mode
This is a list of listening modes you can select according to Multich PCM Direct Dolby Atmos Direct
the audio format of the input signal. • You can select the
Multich Dolby Atmos
1
Dolby Digital Plus or

Input Format Listening Mode Dolby Surround Dolby TrueHD listening Game-RPG
Analog Direct DTS Neural:X modes if a surround Game-Action
back speaker or
Game-RPG Game-Rock
2
Dolby Surround
Game-Action Game-Sports
2
DTS Neural:X connected.
Game-Rock AllCh Stereo
2
Game-RPG
1
Game-Sports Full Mono

2
Game-Action
1
AllCh Stereo T-D

3
Game-Rock
1
Full Mono
3
Game-Sports Input Format Listening Mode
1
AllCh Stereo
2
T-D Dolby D Direct
Full Mono A center speaker or surround speakers need to be installed. Dolby D
2 1 1 2
T-D 3 A center speaker, surround speakers, or height speakers need to be Dolby Surround
installed.
1 Surround speakers or height speakers need to be installed. DTS Neural:X
2 A center speaker, surround speakers, or height speakers need to be Input Format Listening Mode
Game-RPG
3
installed.
DSD Direct
Input Format Listening Mode Game-Action
3
DSD
1 2
PCM Direct Game-Rock

3
Music files (except DSD/ Dolby Surround

Dolby Surround Game-Sports
3
Dolby TrueHD) DTS Neural:X
DTS Neural:X AllCh Stereo
4
Game-RPG
3
Game-RPG
1
Full Mono
4
Game-Action
3
Game-Action
1
T-D
Game-Rock
3
Game-Rock
1
1 Cannot be selected when the input format is 2 ch.
Game-Sports
3
Game-Sports
1
AllCh Stereo
4
AllCh Stereo
2
installed.
Full Mono
4
Full Mono
2
T-D
T-D 1 Cannot be selected when the input format is monaural or 2 ch.
1 Surround speakers or height speakers need to be installed. 2 A center speaker or surround speakers need to be installed.
2 A center speaker, surround speakers, or height speakers need to be 3 Surround speakers or height speakers need to be installed.
installed. 4 A center speaker, surround speakers, or height speakers need to be
installed.
45
Dolby D+ Direct DTS Direct DTS Express Direct
Dolby D+ DTS DTS Express
1 2 1 2 1 2

Game-RPG Game-RPG Game-RPG
3 3 3
Game-Action Game-Action Game-Action

3 3 3
Game-Rock Game-Rock Game-Rock

3 3 3
Game-Sports Game-Sports Game-Sports

3 3 3

4 4 4

4 4 4
T-D T-D T-D

Dolby TrueHD Direct DTS 96/24 Direct DTS-HD HR Direct
Dolby TrueHD DTS 96/24 DTS-HD HR
1 2 1 2 1 2

Game-RPG Game-RPG Game-RPG
3 3 3
Game-Action Game-Action Game-Action

3 3 3
Game-Rock Game-Rock Game-Rock

3 3 3
Game-Sports Game-Sports Game-Sports

3 3 3

4 4 4

4 4 4
T-D T-D T-D

46
Input Format Listening Mode Input Format Listening Mode

DTS-HD MSTR Direct DTS-ES Direct
DTS-HD MSTR DTS
1 2 1
Dolby Surround ES Matrix

2
DTS Neural:X ES Discrete

2
Game-RPG Dolby Surround

3 3
Game-Action DTS Neural:X

3
Game-Rock Game-RPG
3 4
Game-Sports Game-Action
3 4
AllCh Stereo Game-Rock

4 4
Full Mono Game-Sports

4 4
T-D AllCh Stereo

5
Full Mono
5
1 Cannot be selected when the input format is 2 ch.
3 Surround speakers or height speakers need to be installed. T-D
installed. 1 This can only be selected when no surround back speaker is connected.
2 Surround back speakers need to be installed.
3 Height speakers need to be installed.
installed.

DTS:X Direct
DTS:X
Game-RPG
1
Game-Action
1
Game-Rock
1
Game-Sports
1
AllCh Stereo
2
Full Mono
2
T-D
installed.
47
To return to the auto tuning mode: Presetting a Radio Station

LINKS
Press MODE on the remote controller again so that

AM/FM radio "TunMode:Auto" appears on the display. The unit tunes
automatically into a radio station.
It allows you to register up to 40 of your favorite AM/FM
radio stations. Registering radio stations in advance allows
you to tune into your radio station of choice directly.
■ Registration Procedure
Tuning into a Radio Station
1. Tune into the AM/FM radio station you want to register.
■ Tuning Automatically 2. Press MEMORY on the remote controller so that the
preset number on the display flashes.
1. Press TUNER on the remote controller several times to
select either "AM" or "FM". 3. While the preset number is flashing (about 8 seconds),
repeatedly press / on the remote controller to select
2. Press MODE on the remote controller so that
a number between 1 and 40.
"TunMode:Auto" appears on the display.
4. Press MEMORY on the remote controller again to
3. Press the cursors / on the remote controller to start
register the station.
automatic tuning.
• When the station is registered, the preset number
• Searching automatically stops when a station is
stops flashing.
found. When tuned into a radio station, the "TUNED"
• Repeat this procedure for all of your favorite AM/FM
indicator on the display lights. When tuned into an
radio stations.
FM radio station, the "FM ST" indicator lights.
• No sound is output while the "TUNED" indicator is
off. ■ Selecting a Preset Radio Station
When FM broadcasts reception is poor: 1. Press TUNER on the remote controller.
Radio waves may be weak depending on the building 2. Press / on the remote controller to select a preset
structure and environmental conditions. In that case, number.
perform the procedure as explained below in "Tuning
Manually" to manually select the desired station.
■ Deleting a Preset Radio Station
■ Tuning Manually 1. Press TUNER on the remote controller.
1. Press TUNER on the remote controller several times to 2. Press / on the remote controller to select the preset
select either "AM" or "FM". number to delete.
3. After pressing MEMORY on the remote controller, press
2. Press MODE on the remote controller so that
CLEAR while the preset number is flashing to delete the
"TunMode:Manual" appears on the display.
preset number.
3. While pressing the cursors / on the remote • When deleted, the number on the display goes off.
controller, select the desired radio station.
• The frequency changes by 1 step each time
you press the button. The frequency changes
continuously if the button is held down and stops
when the button is released. Tune by looking at the
display.
48
Using RDS (European, Australian and Asian Easy M (Middle of the road music)
models) Light M (Light classics)
Classics (Serious classics)
RDS stands for Radio Data System and is a method of Other M (Other music)
transmitting data in FM radio signals. In regions using Weather
RDS, the radio station name is displayed when you tune Finance
into a radio station broadcasting program information. Children (Children's programmes)
When you press on the remote controller in this state, Social (Social affairs)
you can use the following functions. Religion
Phone In
Travel
■ Display text information (Radio Text) Leisure
1. While the name of the station is being displayed on the Jazz (Jazz music)
display, press on the remote controller once. Country (Country music)
Radio Text (RT) broadcast by the station is displayed Nation M (National music)
scrolling across the display. "No Text Data" is displayed Oldies (Oldies music)
when no text information is available. Folk M (Folk music)
• Unusual characters may be displayed when the unit Document (Documentary)
receives unsupported characters. However, this is not • The information displayed may sometimes not
a malfunction. Also, if the signal from a station is weak, match the content being broadcast by the station.
information may not be displayed. 3. When a station is found, the station flashes on the
display. Press ENTER while this is happening to start
receiving that station. If you don't press ENTER, the unit
■ Search for stations by Program Type
continues to search for another station.
1. While the name of the station is being displayed on the • If no stations are found, the message "Not Found" is
display, press on the remote controller twice. displayed.
2. Press / on the remote controller to select the • Unusual characters may be displayed when the unit
Program Type you want to find, then press ENTER to receives unsupported characters. However, this is
start the search. not a malfunction. Also, if the signal from a station is
The Program Types displayed are as follows: weak, information may not be displayed.
None
News (News reports)
Affairs (Current affairs)
Info (Information)
Sport
Educate (Education)
Drama
Culture
Science (Science and technology)
Varied
Pop M (Pop music)
Rock M (Rock music)
49
interruption in sound. : Pause

• To return to the previous screen, press . : Artist
USB Storage Device
: Album
Operations with the remote controller:
: Repeat One Track
4
■ Playing Back
: Repeat within a folder
Play music files on a USB storage device.
1 : Shuffle
1. Switch the input on the TV to that assigned to the unit.
2. Plug your USB storage device with the music files into
■ USB Storage Device Requirements
the USB port of this unit.
• This unit can use USB storage devices that comply with
3. Press NET on the remote controller to display the
the USB mass storage device class standard.
network service list screen.
• FAT16 or FAT32 file system format.
5 • If the USB storage device has been partitioned, each
2 6 section will be treated as an independent device.
• Up to 20,000 tracks per folder can be displayed, and
3
folders may be nested up to 16 levels deep.
• USB hubs and USB storage devices with hub functions
1 / : When the folder or file lists are not shown on one are not supported. Do not connect these devices to the
screen, you can change the screen.
unit.
2 : This button plays the previous track. • USB storage devices with security function are not
3 : This button lets you start repeat or random
supported on this unit.
playback. Pressing this button repeatedly cycles • If you connect a USB hard disk drive to the USB port of
4. With the cursors on the remote controller, select "USB", through the repeat modes.
the unit, we recommend that you use its AC adapter to
and then press ENTER. 4 : Pressed during play, this button changes the power it.
• If the "USB" indicator flashes on the display, check displayed track information. Pressed while a folder or • Media inserted to the USB card reader may not be
whether the USB storage device is plugged in file list is displayed, this button returns you to the play
available in this function. Furthermore, depending on
properly. screen.
the USB storage device, proper reading of the contents
• Do not unplug the USB storage device while 5 : Pressed during play this button pauses
may not be possible.
"Connecting..." is appeared on the display. This may playback. Pressed while paused, and it restarts play. • Our company accepts no responsibility whatsoever for
cause data corruption or malfunction. 6 : This button plays the next track.
the loss or damage to data stored on a USB storage
5. Press ENTER on the remote controller again in the next device when that device is used with this unit. We
screen. The list of folders and music files on the USB Icons Displayed during Playback: recommend that you back up your important music files
storage device are displayed. Select the folder with the Icons are displayed on the display during music file beforehand.
cursors and press ENTER to confirm your selection. playback. The meaning of each icon is as follows:
6. With the cursors on the remote controller, select the
: Folder ■ Supported Audio Formats
music file, and then press ENTER to start playback.
• The USB port of this unit conforms with the USB 2.0 : Track For server playback and playback from a USB storage
standard. The transfer speed may be insufficient device, this unit supports the following music file formats.
for some content you play, which may cause some : Play Note that sound files that are protected by copyright cannot
50
be played on this unit. TX-RZ810 : 2.8 MHz, 5.6 MHz, 11.2 MHz
Others : 2.8 MHz, 5.6 MHz
MP3 (�mp3/�MP3):
• Supported formats: MPEG-1/MPEG-2 Audio Layer 3 Dolby TrueHD (�vr/�mlp/�VR/�MLP):
• Supported sampling rates: 44.1 kHz, 48 kHz • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
• Supported bitrates: Between 8 kbps and 320 kbps. 96 kHz, 176.4 kHz, 192 kHz
Incompatible files cannot be played.
• Variable bit-rate (VBR) files are supported. However,
WMA (�wma/�WMA): playback times may not be displayed correctly.
• Supported sampling rates: 44.1 kHz, 48 kHz • This unit supports the gapless playback of the USB
• Supported bitrates: Between 5 kbps and 320 kbps. storage device in the following conditions.
Incompatible files cannot be played. When playing WAV, FLAC and Apple Lossless, and
• WMA Pro/Voice/WMA Lossless formats are not the same format, sampling frequency, channels and
supported quantization bit rate are played continuously
WAV (�wav/�WAV):
WAV files include uncompressed PCM digital audio.
• Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
• Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (�aiff/�aif/�aifc/�afc/�AIFF/�AIF/�AIFC/�AFC):
AIFF files include uncompressed PCM digital audio.
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
AAC (�aac/�m4a/�mp4/�3gp/�3g2/�AAC/�M4A/�MP4/�3GP/�3G2):
• Supported formats: MPEG-2/MPEG-4 Audio
88.2 kHz, 96 kHz
• Supported bitrates: Between 8 kbps and 320 kbps.
FLAC (�flac/�FLAC):
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
Apple Lossless (�m4a/�mp4/�M4A/�MP4):
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
• Quantization bit: 16 bit, 24 bit
DSD (�dsf/�dff/�DSF/�DFF):
• Supported formats: DSF/DSDIFF
• Supported sampling rates:
51
Operations with the remote controller: top list on the unit, and then enter your user name and
password.
Internet Radio 2 • If you associate the device on My Page within the
TuneIn Radio website using the registration code
obtained by selecting "Login" - "Login with a registration
1 code" on the unit, you can log in without entering the
TuneIn Radio user name and password.
With more than 70,000 radio stations and 2 million on- ■ Icons on the display
demand programs registered, TuneIn Radio is a service
where you can enjoy music, sports and news from all over 1 / : When the station or program lists are not shown : Folder
the world. on one screen, you can change the screen.
2 : Pressed during play, this button changes the : Radio station
displayed track information. Pressed while a station or : Playing
■ Playing Back program list is displayed, this button returns you to the
1. Switch the input on the TV to that assigned to the unit. play screen. : Artist
2. Press NET on the remote controller to display the : Album
network service list screen. ■ Regarding the TuneIn Radio Menu
To display the TuneIn Radio menu during play, press
ENTER on the remote controller. Selecting the
corresponding menu item with the cursors and pressing
ENTER allows you to perform the following operations:
Add to My Presets: Registers radio stations being

broadcast and programs in "My Presets". Once registered,
"My Presets" is displayed in the level under TuneIn Radio.
To play, select the program you like from "My Presets".
Remove from My Presets: Removes a radio station or
3. Select "TuneIn" with the cursors of the remote controller
program from "My Presets".
and press ENTER to confirm your selection.
4. Follow the on-screen instructions, using the cursors
on the remote controller to select radio stations and ■ Regarding the TuneIn Radio Account
programs, then press ENTER to play. Creating an account on the TuneIn Radio website
Play starts when 100% is displayed for buffering. (tunein.com) and logging in it from the unit allows you
• To return to the previous screen, press . to automatically add your favorite radio stations and
programs to your "My Presets" on the unit as you follow
them on the website. "My Presets" are displayed in the
level under TuneIn Radio.
To display a radio station registered in "My Presets", you
must log into TuneIn Radio from the unit. To log in, select
"Login" - "I have a Tunein Account" in the "TuneIn Radio"
52
PandoraR–Getting Started (U�S�, Australia and have a Pandora Account" and logging in with your email ■ Regarding the Pandora Menu
New Zealand only) and password.
Icons are displayed at the bottom right of the screen while
5. To play a station, use / on the remote controller to playing a station. You can do the following by selecting
Pandora is a free, personalized Internet radio service that select the station from your station list, and then press the icon with / on the remote controller and pressing
plays the music you know and helps you discover music ENTER. Playback starts and the playback screen ENTER:
you'll love. appears.
• To return to the previous screen, press . （I like this track）: Give a track "thumbs-up" and
Pandora will play more music like it.
■ Playing Back
（I don't like this track）: Give a track "thumbs-down"
1. Switch the input on the TV to that assigned to the unit. Operations with the remote controller:
and Pandora will ban that track from the current station.
2. Press NET on the remote controller to display the 2 : Automatically find stations matching your preferences
network service list screen. based on genre, specific artists, and songs, and delete
those stations you don't need.
1
■ Icons on the display
: Folder
: Radio station
3 : Playing
4
: Pause
3. With the cursors on the remote controller, select
"Pandora", and then press ENTER. : Artist
4. Use / on the remote controller to select "I have a 1 / : When the station or program lists are not shown
Pandora Account" or "I'm new to Pandora" and then : Album
on one screen, you can change the screen.
press ENTER. 2 : Pressed during play, this button changes the
If you are new to Pandora, select "I'm new to Pandora". displayed track information. Pressed while a station or
You will see an activation code on your TV screen. program list is displayed, this button returns you to the
Please write down this code. Go to an Internet play screen.
connected computer and point your browser to www. 3 : Pressed during play this button pauses
pandora.com/onkyo. Enter your activation code and playback. Pressed while paused, and it restarts play.
then follow the instructions to create your Pandora 4 : This button plays the next track.
account and your personalized Pandora stations. You
can create your stations by entering your favorite tracks
and artists when prompted. After you have created ■ Create new station
your account and stations you can return to your Enter the name of a track, artist, or genre and Pandora will
receiver and press ENTER to begin listening to your create a unique radio station for you based on the musical
personalized Pandora. qualities of that track, artist, or genre.
If you have an existing Pandora account, you can add
your Pandora account to your receiver by selecting "I
53
Spotify 3
■ Icons on the display

: Playing
This unit supports Spotify Connect. To enable Spotify
Connect, install the Spotify application on your smartphone : Pause
or tablet and create a Spotify premium account.
• This unit needs to be connected to the same router as : Artist
the smartphone or tablet.
: Album
• Refer to the following for Spotify settings: 4
www.spotify.com/connect/ 1 5
• The Spotify software is subject to third party licenses
found here: 2
www.spotify.com/connect/third-party-licenses
1 : This button plays the previous track.
2 : This button lets you start repeat or random
■ Playing Back playback. Pressing this button repeatedly cycles
1. Connect the smartphone to the network that this unit is through the repeat modes.
connected to. 3 : Pressed during play, this button changes the
displayed track information.
2. When the power of this unit is on, click the Connect icon
4 : Pressed during play this button pauses
in the track play screen of the Spotify app.
playback. Pressed while paused, and it restarts play.
3. Select this unit. 5 : This button plays the next track.
4. The input selector of this unit automatically changes to
NET and streaming of Spotify starts.
■ Notes for using multi-zone (for compatible
• When "Network Standby" in the Setup menu is set to
"On", by clicking the Connect icon and selecting this models only)
unit, then even if this unit is in standby mode, the power • To enjoy Spotify music in a separate room, manually
will come on automatically and streaming starts. select "NET" as the input of the separate room. After
doing that, select this unit with the Spotify app.
• Volume adjustment with the Spotify app is possible only
for speakers connected to the ZONE speaker terminals
or when the volume of the audio device in the other
room is configured so that its volume can be adjusted
on this unit. Adjust the volume on the audio equipment
in the other room in any other case.
• To enjoy Spotify music in the main room after playing
it in a separate room, select "NET" as the input of the
main room.
54
Configuring the Windows MediaR Player Play
Music Server ■ Windows MediaR Player 11 1. Start the server (Windows MediaR Player 11, Windows
MediaR Player 12, or NAS device) containing the music
1. Turn on your PC and start Windows MediaR Player 11.
files to play.
2. In the "Library" menu, select "Media Sharing" to display
2. Make sure that the PCs and/or NASs are properly
a dialog box.
Overview connected to the same network as this unit.
3. Select the "Share my media" check box, and then click
3. Press NET on the remote controller to display the
Streaming play of music files stored on PCs or NAS "OK" to display the compatible devices.
network service list screen.
devices connected to the same network as this unit is 4. Select this unit, and then click "Allow". • If the "NET" indicator flashes in the display, the unit
supported. • When it is clicked, the corresponding icon is is not properly connected to the network. Check the
• The network servers this unit is compatible with checked. connection.
are those PCs with players installed that have the 5. Click "OK" to close the dialog.
server functionality of Windows MediaR Player 11 or • Depending of the version of Windows MediaR Player,
12, or NAS that are compatible with home network there may be differences in the names of items you can
functionality. You may need to make some settings in select.
advance to use Windows MediaR Player 11 or 12. Note
that only music files registered in the library of Windows
MediaR Player can be played. ■ Windows MediaR Player 12
2. In the "Stream" menu, select "Turn on media streaming"
to display a dialog box.
• If media streaming is already turned on, select 4. With the cursors on the remote controller, select "Music
"More streaming options..." in the "Stream" menu to Server", and then press ENTER.
list players in the network, and then go to step 4. 5. Select the target server with the cursors on the remote
3. Click "Turn on media streaming" to list players in the controller and press ENTER to display the items list
network. screen.
• The unit cannot access pictures and videos stored
4. Select this unit in "Media streaming options" and check on servers.
that it is set to "Allow". • Contents stored on the server may not be displayed
5. Click "OK" to close the dialog. depending on the server sharing settings.
• Depending of the version of Windows MediaR Player,
6. With the cursors on the remote controller, select the
there may be differences in the names of items you can
music file to play, and then press ENTER to start
select.
playback.
• If "No Item." is displayed, check whether the network
is properly connected.
• To return to the previous screen, press .
• For music files on a server, there can be up to 20,000

tracks per folder, and folders may be nested up to 16
55
levels deep. : Playing Controlling Remote Playback from a PC

• Depending on the media server, the unit may not
recognize it, or may not be able to play its music files. : Pause You can use this unit to play music files stored on your PC
: Artist by operating the PC inside your home network. The unit
supports remote playback with Windows MediaR Player 12.
: Album To use the remote playback function with Windows MediaR
4 Player 12, it must be configured in advance.
: Repeat One Track
: Repeat within a folder ■ Setting PC

1
: Shuffle 1. Turn on your PC and start Windows MediaR Player 12.
2. In the "Stream" menu, select "Turn on media streaming"
to display a dialog box.
• If media streaming is already turned on, select
"More streaming options..." in the "Stream" menu to
list players in the network, and then go to step 4.
5
2 6 3. Click "Turn on media streaming" to list players in the
network.
3
4. Select this unit in "Media streaming options" and check
that it is set to "Allow".
1 / : When the folder or file lists are not shown on one
screen, you can change the screen. 5. Click "OK" to close the dialog box.
2 : This button plays the previous track. 6. Open the "Stream" menu and check that "Allow remote
3 : This button lets you start repeat or random control of my Player..." is checked.
playback. Pressing this button repeatedly cycles • Depending of the version of Windows MediaR Player,
through the repeat modes. there may be differences in the names of items you can
4 : Pressed during play, this button changes the select.
displayed track information. Pressed while a folder or
file list is displayed, this button returns you to the play
screen. ■ Remote playback
5 : Pressed during play this button pauses 1. Turn on the power of the unit.
playback. Pressed while paused, and it restarts play.
6 : This button plays the next track.
3. Select and right-click the music file to play with
Windows MediaR Player 12.
Icons Displayed during Playback: • To remotely play a music file on another server,
Icons are displayed on the display during music file open the target server from "Other Libraries" and
playback. The meaning of each icon is as follows: select the music file to play.
: Folder 4. Select this unit in "Play to" to open the "Play to" window
of Windows MediaR Player 12 and start playback on the
: Track unit.
• Operations during remote playback are possible
56
from the "Play to" window on the PC. The playback Supported Audio Formats • Supported sampling rates: 44.1 kHz, 48 kHz
screen is displayed on the TV connected to the • Quantization bit: 16 bit
HDMI output of the unit. If your PC is running on This unit supports the following music file formats. Note Apple Lossless (�m4a/�mp4/�M4A/�MP4):
WindowsR 8, click "Play to", and then select this that playback via wireless LAN of sampling rates of 88.2 • Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
unit. kHz or higher, DSD, and Dolby TrueHD are not supported. 88.2 kHz, 96 kHz
5. Adjust the volume using the volume bar on the "Play to" Remote play of FLAC, DSD, and Dolby TrueHD is also not • Quantization bit: 16 bit, 24 bit
window. supported.
DSD (�dsf/�dff/�DSF/�DFF):
• Sometimes, the volume displayed on the remote MP3 (�mp3/�MP3): • Supported formats: DSF/DSDIFF
playback window may differ from that appeared on • Supported formats: MPEG-1/MPEG-2 Audio Layer 3 • Supported sampling rates:
the display of the unit. • Supported sampling rates: 44.1 kHz, 48 kHz TX-RZ810 : 2.8 MHz, 5.6 MHz, 11.2 MHz
• When the volume is adjusted from the unit, the value • Supported bitrates: Between 8 kbps and 320 kbps. Others : 2.8 MHz, 5.6 MHz
is not reflected in the "Play to" window. Incompatible files cannot be played.
• This unit cannot play music files remotely in the • Variable bit-rate (VBR) files are supported. However,
following conditions. WMA (�wma/�WMA): playback times may not be displayed correctly.
−− It is using a network service. • Supported sampling rates: 44.1 kHz, 48 kHz • Remote playback does not support the gapless
−− It is playing a music file on a USB storage • Supported bitrates: Between 5 kbps and 320 kbps. playback.
device. Incompatible files cannot be played.
• WMA Pro/Voice/WMA Lossless formats are not
• Depending of the version of Windows MediaR Player, supported
there may be differences in the names of items you can
select. WAV (�wav/�WAV):
WAV files include uncompressed PCM digital audio.
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
AIFF (�aiff/�aif/�aifc/�afc/�AIFF/�AIF/�AIFC/�AFC):
AIFF files include uncompressed PCM digital audio.
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
AAC (�aac/�m4a/�mp4/�3gp/�3g2/�AAC/�M4A/�MP4/�3GP/�3G2):
• Supported formats: MPEG-2/MPEG-4 Audio
88.2 kHz, 96 kHz
• Supported bitrates: Between 8 kbps and 320 kbps.
FLAC (�flac/�FLAC):
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
LPCM（Linear PCM）:
57
Other Functions
Playing Audio and Video from Separate Sources
It is possible to play audio and video from different

sources. For example, you can play audio from the CD
player and video from the BD/DVD player. The procedure
in this case is as follows:
1. Press BD/DVD.
2. Press CD.
3. Start playback on the BD/DVD player and CD player.
Perform the following steps to play the video from

a different source to suit the audio from a NET or
BLUETOOTH input source.
1. Press NET or to play the audio.

2. Press MODE on the remote controller and the video
input select immediately preceding this operation can
be played.
3. Start play of the video input source.
4. Each press of MODE displays or turns off the video.
58
Power Audio
LINKS
Troubleshooting ■ Cannot turn on the unit • Make sure that the speaker setup microphone is not still
• Make sure that the power cord is properly plugged into connected.
the wall outlet. • Confirm that the connection between the output jack on
• Unplug the power cord from the wall outlet, wait 5 the device and the input jack on this unit is correct.
Before starting the procedure seconds or more, then plug it in again. • Make sure that none of the connecting cables are bent,
twisted, or damaged.
■ The unit turns off unexpectedly
• If the MUTE indicator on the display flashes, press
Problems may be solved by simply turning the power on/ • The unit automatically switches to standby when the
on the remote controller to cancel muting.
off or disconnecting/connecting the power cord, which "Hardware" - "Power Management" - "Auto Standby"
• While headphones are connected to the PHONES jack,
is easier than working on the connection, setting and setting in the Setup menu functions.
no sound is output from the speakers.
operating procedure. Try the simple measures on both the • The protective circuit function may have been activated.
• When "Source" - "Audio Select" - "PCM Fixed Mode" in
unit and the connected device. If the problem is that the If this has occurred, "AMP Diag Mode" appears on the
the Setup menu is set to "On", no sound is played when
video or audio is not output or the HDMI linked operation display when the unit is turned on again, and the unit
signals other than PCM are input. Change the setting to
does not work, disconnecting/connecting the HDMI cable enters diagnostic mode. If the results of the diagnosis is
Off.
may solve it. When reconnecting, be careful not to wind that there is no problem, the "AMP Diag Mode" display
the HDMI cable since if wound the HDMI cable may not disappears and you can use the unit normally again. If Check the following if the above does not fix the problem:
fit well. After reconnecting, turn off and on the unit and the "CHECK SP WIRE" appears on the display, the speaker
connected device. cables may be short-circuited. Make sure bare speaker ■ There is no sound from the TV
• This unit contains a microPC for signal processing wires are not touching each other or the back panel of • Change the input selector on this unit to the position of
and control functions. In very rare situations, severe the unit, then turn the unit on again. If "NG" is displayed, the terminal to which the TV is connected.
interference, noise from an external source, or static immediately unplug the power cord from the wall outlet • If the TV doesn't support the ARC function, along with
electricity may cause it to lockup. In the unlikely event and contact your dealer. connection by HDMI, connect the TV and this unit using
that this happens, unplug the power cord from the wall • The protective circuit function may have been activated a digital optical cable, digital coaxial cable, or analog
outlet, wait at least 5 seconds, and then plug it back in. because the temperature of the unit rose abnormally. audio cable.
• Our company is not responsible for reparations for If this happens, then the power will continue to turn off ■ No sound from a connected player
damages (such as CD rental fees) due to unsuccessful after you have turned the unit on again. Make sure the • Change the input selector on this unit to the position of
recordings caused by the unit's malfunction. Before you unit has plenty of space for ventilation around it, wait for the terminal to which the player is connected.
record important data, make sure that the material will the unit to cool down sufficiently, and then try turning it • Check the digital audio output setting on the connected
be recorded correctly. on again. component. On some game consoles, such as those
WARNING: If smoke, smell or abnormal noise is produced that support DVD, the default setting is off.
by the unit, unplug the power cord from the wall outlet • With some DVD-Video discs, you need to select an
immediately and contact the dealer or our company's audio output format from a menu.
support. ■ A speaker produces no sound
• Make sure that the polarity of the speaker cables (＋/－)
is correct, and that no bare wires are in contact with the
metal part of speaker terminals.
• Make sure that the speaker cables are not shorting.
• Check in "Connect the Speakers" in the Basic Manual
that the speaker connections have been made correctly.
Settings for the speaker connection environment need
59
to be made in "AccuEQ Room Calibration" in Initial Listening Modes • With some CD and LD players, you will not be able
Setup. Check in "Initial Setup" in the Basic Manual. to playback DTS material properly even though your
• Depending on the source and current listening mode, • To enjoy digital surround playback, such as Dolby player is connected to a digital input on the unit. This is
not much sound may be produced by the surround Digital, the audio signals need to pass through a usually because the DTS bitstream has been processed
speakers. Select another listening mode to see if sound connection via HDMI cable, digital coaxial cable, or (e.g., output level, sampling rate, or frequency response
is output. digital optical cable. Audio output should be set to changed) and the unit does not recognize it as a
• If you are installing surround back speakers (for bitstream output on the connected Blu-ray Disc player genuine DTS signal. In such cases, you may hear
compatible models only), surround speakers are or other device. noise.
required. • Press on the remote controller several times to • Playing DTS program material, using the pause, fast
• A maximum of 5.1 ch playback is possible when Bi- switch the display of the main unit to check the input forward, or fast reverse function on your player may
Amping connection is used (for compatible models format. produce a short audible noise. This is not a malfunction.
only). Further, make sure you remove the jumper bar on
Check the following if the above does not fix the problem:
the speakers when using Bi-Amping connection.
■ The subwoofer produces no sound ■ Cannot select a desired listening mode
• When you play source material that contains no • Depending on the connecting status of the speaker,
information in the LFE channel, the subwoofer produces some listening modes may not be selected. Check in
no sound. "Selectable Listening Modes" in "Listening Modes" in
the Advanced Manual.
■ Noise can be heard
• Using cable ties to bundle audio cables with power ■ There is no sound with Dolby TrueHD, Dolby Atmos,
cords, speaker cables, etc. may degrade the audio and DTS-HD Master Audio (for compatible models
performance, so refrain from doing it. only)
• An audio cable may be picking up interference. Try • You need to connect surround back speakers or height
repositioning your cables. speakers to enjoy Dolby Atmos. Furthermore, Dolby
Atmos can only be enjoyed when the input signals are
■ The beginning of audio received by an HDMI IN
Dolby Atmos.
cannot be heard • If you cannot output formats such as Dolby TrueHD,
• Since it takes longer to identify the format of an HDMI
Dolby Atmos, or DTS-HD Master Audio according to the
signal than it does for other digital audio signals, audio
format of the source, in the Blu-ray Disc player settings
output may not start immediately.
try setting BD video supplementary sound (or re-
■ Sound suddenly reduces encode, secondary sound, video additional audio, etc.)
• When the temperature inside the unit exceeds a certain to Off . Change the listening mode for each source
temperature for extended periods, the volume may be after changing the setting to confirm.
reduced automatically to protect the circuits.
■ Cannot select Pure Audio mode (for compatible
models only)
• The Pure Audio mode cannot be selected while the
Multi-zone feature (for compatible models only) is on.
■ About DTS signals
• With media that switches suddenly from DTS to PCM,
PCM playback may not start immediately. In such
cases, you should stop your player for about 3 seconds
and then resume playback.
60
Video • Reliable operation with an HDMI-DVI adapter is not Linked operation

guaranteed. In addition, video signals from a PC are not
• Confirm that the connection between the output jack on supported. ■ There is no linked operation with CEC compliant
the device and the input jack on this unit is correct. devices, such as a TV�
• Make sure that none of the connecting cables are bent, ■ Images flicker • In the Setup menu of the unit, set "Hardware" - "HDMI" -
twisted, or damaged. • It is possible that the resolution of the player is not "HDMI CEC" to "On".
• When the TV image is blurry or unclear, power code or compatible with the TV's resolution. If you have • It is also necessary to set HDMI linking on the CEC
connection cables of the unit may have interfered. In connected the player to this unit with an HDMI cable, try compliant device. Check the instruction manual.
that case, keep distance between TV antenna cable and changing the output resolution on the player. There also
cables of the unit. may be an improvement if you change the screen mode
• Make sure the switching of input screens is proper at on the TV. Tuner
the monitor side such as a TV.
■ Video and audio are out of synch ■ Radio reception is poor or there is a lot of noise�
Check the following if the above does not fix the problem: • Video may be delayed relative to audio depending on • Re-check the antenna connection.
the settings and connections with your television. To • Relocate your antenna.
■ There is no video adjust, press Q on the remote controller, and adjust in • Move the unit away from your TV or PC.
• Change the input selector on this unit to the position of "Other" - "A/V Sync" in the "Quick Menu". • Passing cars and airplanes can cause interference.
the terminal to which the player is connected.
• Concrete walls weaken radio signals.
• While the listening mode is Pure Audio (for compatible
• Listen to the station in mono.
models only), the video signals input through jacks
• When listening to an AM station, operating the remote
other than the HDMI IN jack cannot be shown.
controller may cause noise.
■ There is no picture from a source connected to an • FM reception may become clearer if you use the
HDMI IN terminal� antenna jack on the wall used for the TV.
• To display video from the connected player on the
TV while the unit is in standby, you need to enable
"Hardware" - "HDMI" - "HDMI Standby Through" in
the Setup menu. Refer to "HDMI Setup" in "Setup" in
the Basic Manual for information about HDMI Standby
Through.
• To output video to a TV connected to the HDMI OUT
SUB jack (for compatible models only), in the "Quick
Menu" displayed when Q is pressed on the remote
controller, select the HDMI OUT jack for output in
"Other" - "HDMI Out".
• If you connect a player supporting HDCP2.2, be sure
to connect it to one of the HDMI IN1 to IN3 jacks of the
unit.
• Check if "Resolution Error" is displayed on the main
unit display when video input via HDMI IN jack is not
displayed. In this case, the TV does not support the
resolution of the video input from the player. Change the
setting on the player.
61
BLUETOOTH function Network function • When using a PC, only music files registered in the
Windows MediaR Player library can be played.
• Try plugging/unplugging the power of the unit and try • If you cannot select a network service, it will become ■ Playback stops while listening to music files on the
turning on/off the BLUETOOTH enabled device. Re- selectable when the network function is started. It may network server
startup of the BLUETOOTH enabled device may be take about a minute to start up. • Make sure the network server is compatible with this
effective. • When NET is blinking, this unit is not properly unit.
• The BLUETOOTH enabled devices must support the connected to the home network. • When the PC is serving as the network server, try
A2DP profile. • Try plugging/unplugging the power supply of this unit quitting any application software other than the server
• Near components such as microwave oven or cordless and the router, and try rebooting the router. software (Windows MediaR Player 12, etc.).
phone, which use the radio wave in the 2.4 GHz range, • If the desired wireless LAN router is not in the access • If the PC is downloading or copying large files, the
a radio wave interference may occur, which disables the point list, it may be set to hide SSID or the ANY playback may be interrupted.
use of this unit. connection may be off. Change the setting and try again.
• If there is a metallic object near the unit, BLUETOOTH
connection may not be possible as the metal can effect USB storage device
on the radio waves. ■ Cannot access the Internet radio
• Certain network service or contents available through ■ USB storage device is not displayed
the unit may not be accessible in case the service • Check whether the USB storage device or USB cable is
■ Cannot connect with this unit provider terminates its service. correctly inserted to the USB port of the unit.
• Check that the BLUETOOTH function of the • Make sure that your modem and router are properly • Disconnect the USB storage device from the unit, and
BLUETOOTH enabled device is enabled. connected, and make sure they are both turned on. then try reconnecting.
• Make sure that the LAN side port on the router is • Performance of the hard disk that receive power from
■ Music playback is unavailable on the unit even after
properly connected to this unit. the USB port of the unit is not guaranteed.
successful BLUETOOTH connection
• Make sure that connecting to Internet from other • Depending on the type of format, the playback may
• When the audio volume of your BLUETOOTH enabled
components is possible. If connecting is not possible, not be performed normally. Check the type of the file
device is set low, the playback of audio may be
turn off all components connected to the network, wait formats that is supported.
unavailable. Volume up the BLUETOOTH enabled
for a while, and then turn on the components again. • USB storage devices with security functions may not be
device.
• If a specific radio station is unavailable for listening, make played.
• Depending on the BLUETOOTH enabled device, Send/
sure the registered URL is correct, or whether the format
Receive selector switch may be provided. Select Send mode.
distributed from the radio station is supported by this unit.
• Depending on the characteristics or specifications of
• Depending on ISP, setting the proxy server is
your BLUETOOTH enabled device, playback on the unit
necessary.
is not guaranteed.
• Make sure that the used router and/or modem is
■ Sound is interrupted supported by your ISP.
• Problem may be occurring at the BLUETOOTH enabled
■ Cannot access the network server
device. Check the information on the internet.
• This unit needs to be connected to the same router as
■ The audio quality is poor after connection with a the network server.
BLUETOOTH enabled device • This unit is compatible with Windows MediaR Player 11
The BLUETOOTH reception is poor. Move the or 12 network servers or NAS that are compatible with
BLUETOOTH enabled device closer to the unit or home network functionality.
remove any obstacle between the BLUETOOTH • You may need to make some settings on Windows
enabled device and this unit. MediaR Player. Check in "Music Server" in "Playback
Function" in the Advanced Manual.
62
Wireless LAN Network on the radio wave. controller may not work reliably.
• When other wireless LAN devices are used near the • After operating the Multi-zone function (for compatible
• Try plugging/unplugging the power supply of wireless unit, several issues such as interrupted playback models only), the remote controller may have switched
LAN router and the unit, check the wireless LAN router and communication may occur. You can avoid these to the mode for operating ZONE output audio. Check
power-on status, and try reboot of the wireless LAN issues by changing the channel of your wireless LAN "Multi-zone" in "Playback" in the Basic Manual to switch
router. router. For instructions on changing channels, see the the remote controller back to the mode for operating in
instruction manual provided with your wireless LAN the main room.
router.
■ Cannot access wireless LAN network Display, OSD
• The wireless LAN router setting may be switched to
Multi-zone function (for compatible models only)
Manual. Return the setting to Auto.
■ The display doesn't light
• Try the manual set-up. The connection may succeed.
■ Cannot ZONE output audio of external AV • The display may go dim while the Dimmer is working,
• When the wireless LAN router setting is at stealth mode
component and may also turn off (for compatible models only).
(mode to hide the SSID key) or when ANY connection
• Depending on the model, input by HDMI cable may Press DIMMER button and change the brightness level
is off, the SSID is not displayed. Change the setting and
not be supported. Check in "Multi-zone Connection" of the display.
try again.
in the Basic Manual, and if input by HDMI cable is not • The display is turned off when the Pure Audio (for
• Check that the setting of SSID and encryption (WEP,
supported, connect using a cable that is supported. compatible models only) listening mode is selected.
etc.) is correct. Make sure the network settings of the
• The audio from externally connected AV components
unit is properly set.
can only be output when the audio is analog or 2ch
• Connection to an SSID that includes multi-byte
PCM audio signals. If you have connected the AV Others
characters is not supported. Name the SSID of the
component to this unit with a digital cable, the audio
wireless LAN router using single-byte alphanumeric
output of the AV component needs to be set to PCM. ■ Strange noises can be heard from the unit
characters only and try again. • If you have connected another unit to the same wall
■ Others outlet as this unit, this noise may be an effect from the
■ Connected to an SSID different to the SSID selected
• Settings are required in Initial Setup, "Multi Zone Setup" other unit. If the symptoms improve by unplugging the
• Some wireless LAN routers allow you to set multiple
to use the multi-zone feature. Check in "Initial Setup" in power cord of the other unit, use different wall outlets for
SSIDs for one unit. If you use the automatic setting
the Basic Manual. this unit and the other unit.
button on such a router, you may end up connecting
• If the audio signal is from the NET input selector, zone
with a different SSID from the SSID you wanted to
output is not possible for DSD and Dolby TrueHD audio ■ When performing AccuEQ Room Calibration, the
connect to. Use the connection method requiring you to message "Noise Error" appears
signals.
enter a password if this happens. • This can be caused by a malfunction in your speaker
■ Playback is interrupted and communication does unit. Check if the unit produces normal sounds.
not work Remote Controller
• You may not receive radio waves due to bad radio wave
conditions. Shorten the distance from the wireless LAN • Make sure that the batteries are installed with the
access point or remove obstacles to improve visibility, correct polarity.
and try again. Place the unit away from microwave • Install new batteries. Do not mix different types of
ovens or other access points. It is recommended to batteries, or old and new batteries.
place the wireless LAN router (access point) and the • Make sure that the unit is not subjected to direct
unit in the same room. sunshine or inverter-type fluorescent lights. Relocate if
• If there is a metallic object near the unit, wireless LAN necessary.
connection may not be possible as the metal can effect • If the unit is installed in a rack or cabinet with colored-
glass doors or if the doors are closed, the remote
63
• We assume no responsibility whatsoever for any error Scope of Operation

LINKS
or damage of network environment or access device

Reference Information resulting from the use of this apparatus.
Confirm with the provider or access device maker for
Use of the AV receiver is limited to home use.
(Transmission distances may be reduced depending on
more information. communication environment.)
In the following locations, poor condition or inability to
Radio Wave Caution receive radio waves may cause the audio to be interrupted
or stopped:
• In reinforced concrete buildings or steel framed or iron
This unit uses radio waves in the 2.4 GHz and 5 GHz
framed buildings.
frequency bands.
• Near large metallic furniture.
There are nations and regions where the use of particular
• In a crowd of people or near a building or obstacle.
5 GHz bands are prohibited outdoors, so do not use this
• In a location exposed to the magnetic field, static
unit outside in those places.
electricity or radio wave interference from radio
2.4 GHz radio waves are used by a variety of devices, as
communication equipment using the same frequency
shown in lists 1 and 2 below.
band (2.4 GHz) as the AV receiver, such as a 2.4 GHz
1. Devices which use a 2.4 GHz radio wave frequency
wireless LAN device (IEEE802.11b/g/n) or microwave
• Cordless phones
oven.
• Cordless facsimiles
• If you live in a heavily populated residential area
• Microwave ovens
(apartment, townhouse, etc.) and if your neighbor's
• Wireless LAN devices (IEEE802.11b/g/n)
microwave oven is placed near your AV receiver, you
• Wireless AV equipment
may experience radio wave interference. If this occurs,
• Wireless controllers for game systems
move your AV receiver to a different place.
• Microwave oven-based health aids
When the microwave oven is not in use, there will be no
• Video transmitter
radio wave interference.
• Specific type of external monitor and LCD display
2. Less common devices which use a 2.4 GHz radio wave
frequency
• Anti-theft systems
• Amateur radio stations (HAM)
• Warehouse logistic management systems
• Discrimination systems for train or emergency
vehicles
If these devices and the AV receiver are used at the same
time, the audio may be undesirably stopped or disturbed
due to a radio wave interference.
Suggestions for improvement
• Switch off the devices which emit the radio wave.
• Place the interfering devices away from the AV
receiver.
• The AV receiver uses radio wave, and a third person
can receive the wave on purpose or accidentally. Do not
use the communication for important or fatal matters.
64
Radio Wave Reflections Precautions
The radio waves received by the AV receiver include the • Do not use this apparatus near an electronic device
radio wave coming directly from the devices and waves handling high-accuracy controls or weak signals. Doing
coming from various directions due to reflections by walls, so may cause an accident due to a malfunction of the
furniture and building (reflected waves). The reflected device.
waves (due to obstacles and reflecting objects) further • Do not use this apparatus in use prohibited location
produce a variety of reflected waves as well as variation such as an aircraft equipment or a hospital. Doing so
in reception condition depending on locations. If the audio may cause an accident due to a malfunction of an
cannot be received properly due to this phenomenon, try electronic device or an electro-medical apparatus.
moving the location of the wireless LAN device a little. Follow the instructions of the medical facilities.
Also note that audio may be interrupted due to the
reflected waves when a person crosses or approaches ■ Electronic device which requires cautions
the space between the AV receiver and the wireless LAN Hearing aid, pace maker, other medical electronic devices,
device. fire alarm, automatic door, and other automatic control
• We assume no responsibility whatsoever for any device.
damages resulting from the use of this apparatus When using a pace maker or other medical electronic
except in the cases deemed acceptable under the devices, confirm with the medical electronic device maker
applicable laws and regulations. or dealer for the effect of the radio wave.
• Operation in all environment is not guaranteed for
wireless LAN. The communication may not be possible
or have desirable communication speed.
65
2-3-12 Yaesu, Chuo-ku, Tokyo 104-0028 JAPAN
http://www.onkyo.com/
<U.S.A.>
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
For Product Support Team Only:
1-800-229-1687
<Germany>
Gutenbergstrasse 3, 82178 Puchheim, Germany
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
<UK>
Anteros Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex,
HA4 6QQ United Kingdom
Tel: +44 (0)871-200-1996 Fax: +44 (0)871-200-1995
<Hong Kong>
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: +852-2429-3118 Fax: +852-2428-9039
http://www.hk.onkyo.com/
<PRC>
302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032,
Tel: +86-21-52131366 Fax: +86-21-52130396
http://www.cn.onkyo.com/
<Asia, Oceania, Middle East, Africa>
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
Корпорация О энд Пи
2-3-12, Яэсу, Чуо-ку, г. Токио, 104-0028, ЯПОНИЯ
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
F1604-0
SN 29402344PDF_EN
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved.
http://www.onkyo.com/privacy/ * 2 9 4 0 2 3 4 4 *

ht-r695 Bas Adv Manual en

Uploaded by

Copyright:

Available Formats

ht-r695 Bas Adv Manual en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ht-r695 Bas Adv Manual en

Uploaded by

Copyright:

Available Formats

> Before start > Hookup > Setup > Playback > Part Names > Advanced Manual

Basic Manual Hookup

The Basic Manual includes information needed when starting up and

What's in the box

Step1: Conect the Speakers

1 2 Dolby Enabled Speakers (Front) ＊1

＊ 1: 22e to 30e, ＊ 2: 120e

Connections for 5.1.2-

1 Speaker cable, 2 Subwoofer cable

Step2: Connect the TV

Another TV or projector can be connected to the HDMI OUT SUB

Step3: Connect the AV Components

You can connect a device such as a video camera to the AUX

Cable/Satellite set-top Streaming media

1 Component video cable, 2 Digital coaxial cable, 3 Analog audio cable

If the turntable has a ground wire, connect it to the GND terminal

1 Digital optical cable, 2 Analog audio cable

Step4: Multi-zone Connection

Connections with an AV component

ZONE 2 LINE OUT

ZONE2 ZONE SPEAKER

1 Digital coaxial cable, 2 Analog audio cable, 3 Speaker cable

Step5: Connect Other Cables

(North American models)

Power Cord Hookup

Connect the power cord to the power outlet after

(Australian and Asian models)

Step6: Power On & Initial Setup

connecting by Wi-Fi: HDMI Standby Through Auto(Eco)

Original surround modes Input signal resolution

AirPlay BLUETOOTH® Playback

You can wirelessly enjoy the music files on an iPhone®, Pairing

Remote Controller Display

Onkyo Corporation no garantiza la compatibilidad BLUETOOTH entre el receptor

Εϭλϟ΍Ε΍έΎη·ϝ˶ΑϘΗγϣ˵ ϥϳΑ %/8(7227+ ΙϭΗϭϠΑϟ΍ϲϓϖϓ΍ϭΗΩϭΟϭ2QN\RϥϣοΗϻ

iPad Air and iPad mini are trademarks of Apple Inc.

2-3-12 Yaesu, Chuo-ku, Tokyo 104-0028 JAPAN

Advanced Manual Specifications

±10 dB, 90 Hz (BASS) Communication system

■ HDMI ■ Audio Inputs

ARC（Audio Return Channel）: Multi-channel linear PCM:

■ 3� Video Input Setting Item Default Value Setting Details

■ 4� Digital Audio Input ■ 5� Analog Audio Input

2� Speaker Setting Item Default Value Setting Details

■ 2� Crossover Setting Item Default Value Setting Details

■ 3� Distance ■ 4� Level Calibration

• Default values vary depending on the regions.

Setting Item Default Value Setting Details ■ 6� Equalizer Settings

3� Audio Adjust ■ 3� LFE Level

Setting Item Default Value Setting Details

Setting Item Default Value Setting Details

Setting Item Default Value Setting Details 5� Hardware

■ 2� Network Setting Item Default Value Setting Details

Setting Item Default Value Setting Details ■ 4� Power Management

Setting Item Default Value Setting Details 6� Multi Zone

7� Miscellaneous ■ 3� Firmware Update

Setting Item Default Value Setting Details ■ 4� Initial Setup

(The remote indicator flashes twice.)

■ 1� AccuEQ Room Calibration Height Speaker Bundled Dolby Speaker

Εϭλϟ΍Ε΍έΎη·ϝ˶ΑϘΗγϣ˵ ϥϳΑ%/8(7227+ΙϭΗϭϠΑϟ΍ϲϓϖϓ΍ϭΗΩϭΟϭ2QN\RϥϣοΗϻ