Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 87 views

    DC220&DC230 Burn Instructions PDF

    Uploaded by

    Luis
    This document provides instructions for burning firmware onto DC220&DC230 decoder boards. It involves: 1) Connecting a USB to UART serial cable from the computer to the decoder board and ensuring the correct COM port is identified. 2) Opening HITOOLS software on the computer, selecting the HI3535 chip, and choosing the "HiBurn" interface to select the firmware file and start the burning process. 3) Clicking "Burn" to start the process, which takes 3-4 minutes over the network, then confirming burn success once complete.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    DC220&DC230 Burn Instructions PDF

    Uploaded by

    Luis
    87 views5 pages
    This document provides instructions for burning firmware onto DC220&DC230 decoder boards. It involves: 1) Connecting a USB to UART serial cable from the computer to the decoder board and ensuring the correct COM port is identified. 2) Opening HITOOLS software on the computer, selecting the HI3535 chip, and choosing the "HiBurn" interface to select the firmware file and start the burning process. 3) Clicking "Burn" to start the process, which takes 3-4 minutes over the network, then confirming burn success once complete.

    Original Title

    DC220&DC230 Burn instructions (1).pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for burning firmware onto DC220&DC230 decoder boards. It involves: 1) Connecting a USB to UART serial cable from the computer to the decoder board and ensuring the correct COM port is identified. 2) Opening HITOOLS software on the computer, selecting the HI3535 chip, and choosing the "HiBurn" interface to select the firmware file and start the burning process. 3) Clicking "Burn" to start the process, which takes 3-4 minutes over the network, then confirming burn success once complete.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    87 views5 pages

    DC220&DC230 Burn Instructions PDF

    Uploaded by

    Luis
    This document provides instructions for burning firmware onto DC220&DC230 decoder boards. It involves: 1) Connecting a USB to UART serial cable from the computer to the decoder board and ensuring the correct COM port is identified. 2) Opening HITOOLS software on the computer, selecting the HI3535 chip, and choosing the "HiBurn" interface to select the firmware file and start the burning process. 3) Clicking "Burn" to start the process, which takes 3-4 minutes over the network, then confirming burn success once complete.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    DC220&DC230 Burn Instructions

    1. Preparation work:

    1) USB to UART serial cable, specifications: USB to UART, 3.3V TTL level, can be chips
    like PL2303, FT232, CH340, etc.

    2) One network switch, the computer and the decoder are connected to the same
    switch through the network cable.

    3) A WIN10 PC,Turn off the firewall.

    4) HITOOLS software installed on PC, choosing chip HI3535 (sent via Wetransfer).

    5) Images file (sent via Wetransfer).

    1
    DC220&DC230 Burn Instructions
    2. Prepare to burn:

    1) USB port of the USB to UART inserted to computer, to check whether COM is
    correctly identified and installed on PC device manager.

    2) The other port is connected to below 3Pin port of the decoder board. 3Pin
    specification is 1.25mm distance. The decoder is connected to the same switch as
    computer through the network cable.
    Note: Right now the decoder not connected with the power adapter.

    2
    DC220&DC230 Burn Instructions

    3) Open HITOOLS software, choosing chip HI3535, choose HiBurn, then comes

    burning interface. Choose the port displayed by Step 1,1；Transfer mode is

    network. Click “Browse” to select the images file.

    3
    DC220&DC230 Burn Instructions

    4) Select .XMLfile of Image files, and select all the files showed in the files.

    4
    DC220&DC230 Burn Instructions
    3. Start to burn:
    1) Click Burn, then click “OK” on the dialog box.

    2) After click “Ok”, connecting the decoder to power adapter, Burn is starting.
    Normally it takes 3-4 minutes according to network conditions, please kindly wait.
    After Burn is successful, the success dialog box will pop up.

    You might also like