Rigel-Pj1 NX FSM en Final 170212

Model Rigel-PJ1 nx/nw
Machine Codes:
Y015/Y016
Field Service Manual
6 January, 2012
Important Safety Notices
• RISK OF ELECTRIC SHOCK DO NOT OPEN

• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore, it is dangerous to make any kind of
contact with any part inside of this unit.
This symbol alerts the user that important literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
• HEATSINK MAY BE ENERGIZED. TEST BEFORE TOUCHING.

• Heat sink located on the power board, is electrified. mark is putted on the primary heat sink.
Pay attention to this area.
During servicing carefully observe the following.

1. OBSERVE ALL PRECAUTIONS
Items and locations that require special care during servicing, such as the cabinet, chassis, and
parts are labelled with individual safety instructions. Carefully comply with these instructions and all
precautions in the instruction manual.
2. BE CAREFUL OF ELECTRIC SHOCK
The chassis carries an AC voltage. If you touch the chassis while it is still alive, you will get a severe
shock. If you think the chassis is alive, use an isolating transformer or gloves, or pull out the plug
before replacing any parts.
3. USE SPECIFIED PARTS
The components have been chosen for minimum flammability and for specific levels of resistance
value and withstand voltage. Replacement parts must match these original specifications. Parts
whose specifications are particularly vital to safe use and maintenance of the set is marked on
the circuit diagrams and parts list.
Substitution of these parts can be dangerous for you and the customer, so use only specified parts.
4. REMOUNT ALL PARTS AND RECONNECT ALL WIRES AS ORIGINALLY INSTALLED
For safety, insulating tape and tubes are used throughout, but some lift-off parts on the printed
wiring board require special attention.
1
All wires are positioned away from high-temperature and high-voltage parts, and, if removed for
servicing, they must be retuned precisely to their original positions.
5. LAMP
Be very careful of the lamp because it generates high heat while it is used at high voltage. When
replacing the bulb, make sure it is cool enough.
6. LENS
Do not look into the lens during projection. This is important to avoid damage to the eyes.
7. SERVICING
At the time of repair or inspection services, use an earth band (wrist band), without fail.
8. RUN A COMPLETE SAFETY CHECK AT THE COMPLETION OF SERVICING
After completion of servicing, confirm that all screws, parts, and wiring, removed or disconnected
for servicing, have been returned to their original positions. Also examine if the serviced sections
and peripheral areas have suffered from any deterioration as a result of servicing. In addition,
check insulation between external metallic parts and blades of walloutlet plugs. This examination is
indispensable in confirming complete establishment of safety.
(Insulation check)
Pull out a plug from a wall outlet to disconnect the connection cable. Then turn on the POWER
switch. Use a 500V megger (Note 2) and confirm that the insulation resistance is 1M or more
between each terminal of the plug and exposed external metal (Note 1). If the measured value is
below the specified level, then it is necessary to inspect and fix the set.
(Note 1)
Exposed external metal....RGB input terminals, control terminals, etc.
(Note 2)
If a 500V megger is not available for an unavoidable reason, then use a circuit tester or the like for
inspection.
2
Symbols and Trademarks
This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations
are as follows:
See or Refer to
Screw
Connector
Trademarks
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States
and /or other countries.
Other product names used herein are for identification purposes only and may be trademarks of their
respective companies. We disclaim any and all rights involved with those marks.
3
TABLE OF CONTENTS
Important Safety Notices...................................................................................................................................1
Symbols and Trademarks...................................................................................................................................3
Trademarks.....................................................................................................................................................3
1. Product Information
Specifications......................................................................................................................................................9
Overview..........................................................................................................................................................10
Front / Top...................................................................................................................................................10
Rear...............................................................................................................................................................11
Top Features.................................................................................................................................................12
Terminal Panel Features...............................................................................................................................13
Part Names of the Remote Control.............................................................................................................15
2. Installation
Installation Requirements.................................................................................................................................19
Fire and Shock Precautions.........................................................................................................................19
3. Replacement and Adjustment
Cautions for Maintenance Service.................................................................................................................25
Method of starting the set without TOP COVER and LAMP COVER.......................................................25
Special Tools....................................................................................................................................................28
Parts Replacement............................................................................................................................................31
Lamp Unit......................................................................................................................................................31
Filters.............................................................................................................................................................32
Port Cover for USB Wireless LAN Unit.......................................................................................................33
Top Cover.....................................................................................................................................................33
PCB Shutter...................................................................................................................................................35
Rear Panel and Speaker.............................................................................................................................36
PCB Main Ass'y............................................................................................................................................38
PCB Network................................................................................................................................................38
Lamp Fan......................................................................................................................................................39
OPT Base......................................................................................................................................................41
Assembling the lens holder (top)........................................................................................................42
IRIS Unit........................................................................................................................................................44
PS-Converter................................................................................................................................................45
LCD Fan 1.....................................................................................................................................................46
4
LCD Fan 2.....................................................................................................................................................48
PCB Remocon...............................................................................................................................................49
Intake Temp Sensor.....................................................................................................................................50
Exhaust Temp Sensor...................................................................................................................................50
Exhaust Fan..................................................................................................................................................51
Thermostat....................................................................................................................................................52
PSU Fan........................................................................................................................................................55
Power Supply-Ballast...................................................................................................................................56
Power Supply-DC........................................................................................................................................56
Bottom Cover...............................................................................................................................................59
Replacement of Optical Parts..........................................................................................................................60
Polarizer-B....................................................................................................................................................60
Polarizer-G...................................................................................................................................................61
Polarizer-R....................................................................................................................................................63
Optical Parts Adjustment.............................................................................................................................63
Adjusting and fixing parts...................................................................................................................64
Adjustment of the optical axis (Shadow adjustment).......................................................................65
Adjustment of the polarization plate (Contrast adjustment).............................................................73
Electrical Adjustment........................................................................................................................................76
Procedures for the replacement of the PCB Main Ass’y...........................................................................77
Outline of adjustment procedules......................................................................................................77
PC control software for service..........................................................................................................78
Model-Specific Data Writing Procedure..........................................................................................91
Procedure for rewriting EDID data....................................................................................................94
Procedure for writing of a serial number and a model number....................................................103
Procedures for the replacement of the OPT Base...................................................................................106
4. System Maintenance
Firmware Upgrade........................................................................................................................................107
Upgrading the firmware...........................................................................................................................107
Functional Test................................................................................................................................................109
Connecting a Computer............................................................................................................................109
Connecting an External Monitor..............................................................................................................112
Connecting a DVD Player or Other AV Equipment................................................................................113
5
Connecting Component Input..................................................................................................................114
Connecting HDMI Input............................................................................................................................115
Connecting to a Wired LAN.....................................................................................................................117
Input signals...............................................................................................................................................118
Signal level........................................................................................................................................118
RGB signal frequencies....................................................................................................................118
HDMI digital signals.........................................................................................................................118
Component signals...........................................................................................................................118
Video input color system..................................................................................................................118
5. Troubleshooting
LED Display....................................................................................................................................................119
Indicator Messages...................................................................................................................................119
Power Indicator.................................................................................................................................119
Status Indicator.................................................................................................................................119
Lamp Indicator..................................................................................................................................120
Over-Temperature Protection..........................................................................................................121
Service Mode.................................................................................................................................................122
List of functions...........................................................................................................................................122
Mode changeover....................................................................................................................................122
Expert mode......................................................................................................................................122
Service mode....................................................................................................................................123
How to withdraw from the mode.....................................................................................................123
Contents of display...........................................................................................................................124
Additional functions (extract)....................................................................................................................124
SETUP–EXPERT1 Tab........................................................................................................................124
SETUP–EXPERT2 Tab........................................................................................................................125
Security functions.......................................................................................................................................125
How to cancel the security functions...............................................................................................125
MM Viewer and Network Area...............................................................................................................126
List of functions..................................................................................................................................126
Additional Functions.........................................................................................................................127
Troubleshooting Guide..................................................................................................................................129
Operation check........................................................................................................................................129
6
Power block...............................................................................................................................................131
For Video....................................................................................................................................................132
For Audio...................................................................................................................................................133
Error Log.........................................................................................................................................................134
Error Log Screen Image............................................................................................................................134
Displaying an error log screen........................................................................................................134
Service Information: Page-1............................................................................................................134
Service Information: Page-2............................................................................................................135
Service Information: Reset................................................................................................................136
Contents of Error Log (Page1) Display....................................................................................................137
Status Columns..................................................................................................................................137
PJ Usage Columns............................................................................................................................138
TEMP Columns..................................................................................................................................138
Other Columns..................................................................................................................................138
Contents of Error Log (Page2) Display....................................................................................................139
TEMP Columns..................................................................................................................................139
Lamp/Filter Clear Count..................................................................................................................139
Power ON/OFF Count....................................................................................................................139
Projector Hours Used........................................................................................................................139
Lamp Voltage: Indicated exceeding the Service Power................................................................140
Contents of Error Log (Reset) Display......................................................................................................140
ALL DATA...........................................................................................................................................140
7
8
Specifications
See "Appendices" for the following information:
• General Specifications
9
Overview
Front / Top
1 Lamp Cover
2 Ventilation (outlet)
3 Lens Cover
4 Lens
5 Adjustable Tilt Foot Lever
6 Adjustable Tilt Foot
7 Controls
8 Focus Lever
9 Zoom Lever
10 Lens Shift Dial (Vertical)
11 Ventilation (inlet) / Filter Cover
10
Overview
12 Remote Sensor
Rear
1 Port Cover for USB Wireless LAN Unit
2 Monaural Speaker
3 Terminal Panel
4 AC Input
5 Remote Sensor
6 Built-in Security Slot
7 Security chain opening
8 Rear Foot
11
Top Features
• While an on-screen menu is displayed, you can use the

, , , and buttons to select the item you want to set
Buttons
or adjust.
1 Used for both volume
• When the on-screen menu is not displayed, the and
adjustment and trapezoid
buttons can be used to adjust the volume level, and the
correction (Keystone Buttons).
and buttons can be used to adjust the trapezoid in
the vertical direction.
Proceeds to the next hierarchical menu in the currently

displayed on-screen menu.
2 Enter Button
Applies the selected item while the confirmation message is
displayed.
Displays an on-screen menu for setting or adjusting a variety

3 Menu Button
of items.
Detects the signal input.

Automatically checks for signal inputs in the following order:
4 Input Button [COMPUTER 1] [COMPUTER 2] [COMPUTER 3]
[HDMI] [DisplayPort] [VIDEO] [S-VIDEO] [Viewer]
[COMPUTER 1]. If it detects a signal input, it projects the
input.
12
Overview
Turn the projector on and then off (standby).
5 Power Button To turn the projector off (standby), then press the Power
button one time. When the confirmation message appears
on the screen, press the Power button again.
6 Status Indicator p.119
Returns to the previous hierarchical menu in the currently

displayed on-screen menu. When the cursor is placed over
7 Back Button
the main menu, the menu closes. When a confirmation
message appears, the operation is canceled.
8 Eco Button Displays the screen for selecting the lamp power level.
Automatically adjust the projector to an optimal state for

9 Auto set Button
projection of a computer screen image.
10 Power Indicator p.119
11 Lamp Indicator p.119
Terminal Panel Features
1 USB Port (Type A)
2 LAN Port (RJ-45)
3 USB (PC) Port (Type B)
4 HDMI In Connector (Type A)
13
5 Computer 2 Audio In Mini Jack (Stereo Mini)
6 Computer 2 In / Component Input Connector (Mini D-Sub 15 Pin)
7 S-Video In Connector (Mini DIN 4 Pin)
8 Computer 1 Audio In Mini Jack (Stereo Mini)
9 Computer 1 In / Component Input Connector (Mini D-Sub 15 Pin)
10 Audio Out Mini Jack (Stereo Mini)
11 PC Control Port (D-Sub 9 Pin)
12 Monitor Out (Comp.1) Connector (Mini D-Sub 15 Pin)
13 Video/S-Video Audio In (L/Mono, R) Connectors (RCA)
14 Video In Connector (RCA)
14
Overview
Part Names of the Remote Control
1 Infrared Transmitter
Pressing the Power button once displays the power-off confirmation

2 Power Standby Button message. Pressing the Power button a second time turns the
projector off (standby).
Confirm that the projector is in standby (the Power indicator is lit

3 Power On Button orange*), and then turn it on.
* When Standby mode is set to "Normal".
15
Select the COMPUTER1/2 input or a component.

4 Computer 1/2/3 Button
(Computer 3 button is not available.)
5 S-Video Button Select the S-VIDEO input.
6 Video Button Select the VIDEO input.
7 Network Button Select the Network.
8 Viewer Button Select the Viewer.
The remote controller that comes with this projector can be used to
9 ID Set Button control multiple projectors. These buttons are used to set the control
ID of an individual projector.
Turns off both video and audio temporarily. Pressing the button
10 AV Mute Button
again turns the video and audio back on.
Displays an on-screen menu for setting or adjusting a variety of

11 Menu Button
items.
Proceeds to the next hierarchical menu in the currently displayed

on-screen menu.
12 Enter Button
Applies the selected item while the confirmation message is
displayed.
13 Magnify (+)(−) Button Used to zoom in and out on the screen.
Used when the machine is connected to a computer via a USB

14 L Click Button*1
cable. Acts as the left mouse button.
15 Eco Button Displays the screen for selecting the lamp power level.
16 Help Button Displays the information screen.
17 Keystone Button Displays the screen for adjusting the trapezoid.
Automatically adjust the projector to an optimal state for projection

18 Auto Set Button
of a computer screen image.
19 HDMI Button Select the HDMI input.
20 USB Display Button Select the USB Display.
16
Overview
The remote controller that comes with this projector can be used to
Numeric Keypad control multiple projectors. These buttons are used to enter the ID
21 (or set the control ID) of an individual projector.
Button/Clear Button
The Clear button can be used to clear the set control ID.
Displays the current video image as a still image. Pressing the

22 Freeze Button
button again returns to normal video display.
Returns to the previous hierarchical menu in the currently displayed

on-screen menu. When the cursor is placed over the main menu,
23 Back Button
the menu closes. When a confirmation message appears, the
operation is canceled.
Used to adjust display position when the screen is enlarged by

using the partial enlargement button or by performing an operation
24 Button*2 in the on-screen menu .
This button is also used as the computer mouse (remote mouse)
when the machine is connected to a computer via a USB cable.
Used to switch the viewer between thumbnail views. This button is

25 Page / Button*1 also used when the machine is connected to a computer via a USB
cable.
Used when the machine is connected to a computer via a USB

26 R Click Button*1
cable. Acts as the right mouse button.
Each time the button is pressed in the on-screen menu, the picture
adjustment item displayed in [PICTURE] of the [ADJUST] menu
27 Picture Mode Button changes. The first item is [PRESET], followed by [CONTRAST],
[BRIGHTNESS], [SHARPNESS], [COLOR SATURATION], and
finally [TINT].
Adjusts the volume of the internal speaker. Also adjusts the volume
28 Volume (+)(−) Button of output sent to the audio output port. Pressing the button again
resets the volume.
29 Aspect Button Displays a set of aspect adjustment items.
*1 Used to operate the computer when the mouse receiver is connected to the computer.
*2 Used as the computer mouse when the mouse receiver is connected to the computer.
17
18
2. Installation
Installation Requirements
• Do not use any other object than the projector’s sliding lens cover to cover the lens while the
projector is on.
• Doing so can cause the object to get extremely hot, and possibly resulting in a fire or damage due
to the heat emitted from the light output.
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any
way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of
heat inside your projector. Allow at least 4 inches (10cm) of space between your projector and a
wall.
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become
heated while the projector is turned on and immediately after the projector is turned off. Parts of the
projector may become temporarily heated if the projector is turned off with the Power button or if
the AC power supply is disconnected during normal projector operation.
Use caution when picking up the projector.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do
not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects
such as a wire or screwdriver into your projector. If something should fall into your projector,
disconnect it immediately and have the object removed by a qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
19
2. Installation
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that
your power supply fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items (magnifying glass etc.) out of the light path of the projector. The light path being
projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light
coming out of the lens, can cause an unpredictable outcome such as a fire or injury to the eyes.
• Do not place any objects, which are easily affected by heat, in front of a projector exhaust vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted
from the exhaust.
• Handle the power cord carefully. A damaged or frayed power cord can cause electric shock or
fire.
• Do not use any power cord other than the one supplied with the projector.
• Do not bend or tug the power cord excessively.
• Do not place the power cord under the projector, or any heavy object.
• Do not cover the power cord with other soft materials such as rugs.
• Do not heat the power cord.
• Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cord and have the projector serviced by a qualified
service personnel under the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the projector, or if it has been exposed to rain or water.
• If the projector does not operate normally when you follow the instructions described in this
user’s manual.
• If the projector has been dropped or the cabinet has been damaged.
• If the projector exhibits a distinct change in performance, indicating a need for service.
• Disconnect the power cord and any other cables before carrying the projector.
• Turn off the projector and unplug the power cord before cleaning the cabinet or replacing the
lamp.
• Turn off the projector and unplug the power cord if the projector is not to be used for an extended
period of time.
• When using a LAN cable (only models with the RJ-45 LAN port):
For safety, do not connect to the connector for peripheral device wiring that might have excessive
voltage.
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping
the tilt-foot or hanging on the wall can cause damage to the projector.
20
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The
projector inside the soft case could be damaged.
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the
menu, select [SETUP] [OPTIONS(1)] [FAN MODE] [HIGH].)
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can
become heated while the projector is turned on and immediately after the projector is turned
off.
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the Power
indicator is blinking blue. Doing so could cause premature lamp failure.
Remote Control Precautions

• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not short, heat, or take apart batteries.
• Do not throw batteries into fire.
• If you will not be using the remote control for a long time, remove the batteries.
• Ensure that you have the batteries’ polarity (+/−) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used batteries according to your local regulations.
Note for US Residents
The lamp in this product contains mercury. Please dispose according to Local, State or Federal
Laws.
Lamp Replacement
• Use the specified lamp for safety and performance.
• To replace the lamp, follow all instructions provided on User’s Manual ( Replacing the Lamp
and the Filters (page 146)).
• Be sure to replace the lamp and filter when the message [THE LAMP HAS REACHED THE END OF
ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.] appears. If you continue to use the
lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly
turning the lamp on and off will increase the possibility of its lower brightness.
21
2. Installation
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the
projector off and then disconnect the power cord. Allow at least one hour for the lamp to cool
before handling.
• When removing the lamp from a ceiling-mounted projector, make sure that no one is under the
projector. Glass fragments could fall if the lamp has been burned out.
About High Altitude mode

• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately
5500 feet/1600 meters or higher.
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without
setting to [HIGH ALTITUDE] can cause the projector to overheat and the protector could shut
down. If this happens, wait a couple minutes and turn on the projector.
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting
to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch
[FAN MODE] to [AUTO].
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten
the life of optical components such as the lamp.
Safety Labels of This Machine
1. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
Do not use any other object than the projector's sliding lens cover to cover the lens while the
projector is on. Doing so can cause the object to get extremely hot, and possibly resulting in a
fire or damage due to the heat emitted from the light output.
2. Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can
become heated while the projector is turned on and immediately after the projector is turned
off. Parts of the projector may become temporarily heated if the projector is turned off with the
Power button or if the AC power supply is disconnected during normal projector operation.
Use caution when picking up the projector.
3. Do not remove any screws except the lamp cover screws. Do not block or cover the vents.
4. To replace the lamp, first unplug the power cord then wait for more than 1 hour. The lamp
might be broken. Be careful of pieces of broken glass.
22
23
2. Installation
24
Cautions for Maintenance Service

Method of starting the set without TOP COVER and LAMP COVER
How to start the set under the condition that the LAMP COVER and TOP COVER are removed
The Lamp Cover switch of this model is mounted on the PCB Main Ass'y.
The set cannot be started if the LAMP COVER and TOP COVER are left removed.
This is because the Lamp Cover switch can be turned OFF only if the LAMP COVER is removed.
In addition, the PCB Shutter (lens cover) is installed on the Top Cover. When the Top Cover is
removed, the status of AV mute is assumed.
Follow the steps shown below when intending to start up the set under the condition that the LAMP
COVER and TOP COVER are removed.
1. Provide for carton (or cardboard paper)

Length: 35 - 40 (mm), Depth: 100 - 120 (mm), Thickness: 1 - 2 (mm)
25
2. Fold the carton (or cardboard paper) in the center in Character V.
[A] : 3P extension board and 3P extension connector

[B] : The lens cover is left opened.
[C] : LAMP COVER SWITCH (ON by PUSH)
[D] : Insert the carton
3. Insert the carton (or cardboard paper) folded in Character V in the right side of the
Lamp Cover switch.
(Insert it along the Lamp Cover switch.)
4. Connect the PCB Main Ass'y and the PCB Shutter with the 3P extension board and
extension connector.
5. The lens cover should be left opened.
26
Cautions for Maintenance Service
• When installing the LAMP COVER and TOP COVER on the set, the TOP COVER only should be
mounted first. Then, the LAMP COVER can be mounted.
• If the installation work is carried out in the state that the LAMP COVER is mounted on the TOP
COVER, the Lamp Cover switch may be damaged by the embossed part of the LAMP COVER.
27
Special Tools
• RS232C cable (cross)
• LAN cable (Category 5 or higher)
Adjusting jig for Adjustment of the optical axis
Q't
Item name Application Part No. Photo taken from life
y
For LCD PANEL

Extension connector (40P) 3 Y0135213
(R/G/B : 600mm)
Extension connector PWB For LCD PANEL

3 Y0135214
(40P) (R/G/B)
For Power supply

Extension connector (16P) (POPW : 500mm) 1 Y0155209
POWER SUPPLY-DC
Extension connector PWB For Power supply

1 Y0155210
(16P) (POWER SUPPLY-DC)
For Power supply

(POLC : 900mm)
POWER SUPPLY-
BALLAST
For Power supply

Extension connector PWB
(POWER SUPPLY- 1 Y0135208
(5P)
BALLAST)
For FAN
Extension connector (4P) (POF1/POF3/POF4 : 3 Y0135205
900mm)
Extension connector PWB For FAN

3 Y0135206
(4P) (POF1/POF3/POF4)
28
Special Tools
Q't
Item name Application Part No. Photo taken from life
y
For FAN
(POF2/POF5 : 900W)
For SHUTTER SW
(PORMMF : 900mm)
For FAN
Extension connector PWB
(POF2/POF5) 3 Y0135204
(3P)
For SHUTTER SW
For THERMISTOR
Extension connector (2P) (POTH-E/POTH-I : 2 Y0135201
900mm)
Extension connector PWB For THERMISTOR

2 Y0135202
(2P) POTH-E/POTH-I)
SPACER RL2 T0.1 (PB52) Y0133125
SPACER RL2 T0.2 (PB52) Y0133126

Spacer for
SPACER RL2 T0.3 (PB52) CLG/CLB/RL2 Y0133127
adjustment
SPACER RL2 T0.5 (PB52) Y0133128
SPACER RL2 T1.0 (PB52) Y0133129
Cautions:
• How to install the FFC cable
Photo seen from above
29
Insert the FFC cable in the relevant connector on the PWB.

Let the embossed part (framed part in blue, shown below) fall down in the direction of the red
arrow.
* The embossed pat for fixing the FFC cable is fragile. Handle it with care when installing or removing the
FFC cable.
30
Parts Replacement
Parts Replacement
Lamp Unit
1. Loosen the screw and remove the Lamp cover ( ×1).
2. Loosen the screw and remove the Lamp unit ( ×2).
31
Filters
1. Remove the Filter cover.
2. Remove the Filters.
32
Parts Replacement
[A] : Air filter A

[B] : Notch
[C] : Filter holder
[D] : Projection
[E] : Air filter B
• When installing filter [A] in the holder, align the notch of the filter with the projection on the holder.
Port Cover for USB Wireless LAN Unit
1. Loosen the screw and remove the Port cover for USB wireless LAN unit ( ×1).
Top Cover
• The PCB Shutter and PCB Main Ass'y mounted on the inside of the top cover are connected by a
lead. Remove them carefully, making sure the top cover faces down towards the lens side.
1. Remove the Lamp unit ( p.31).
33
2. Remove the Filters ( p.32).
3. Top cover [A] ( ×8)

When removing the top cover, make sure to keep the lens cover open.
It might be difficult to remove the cover due to projections inside the chassis. Be careful not to
damage the cover or other parts when removing the cover from inside the chassis.
34
Parts Replacement
There is a cable connecting the TopCover to the main unit. Exercise care when removing the
TopCover.
PCB Shutter
1. Top cover ( p.33).
2. Remove the PCB Shutter ( ×1, ×1).
35
Rear Panel and Speaker
36
Parts Replacement
2. Remove the Main board unit ( ×6, ×15).
3. Remove the screw ( ×1).
4. Remove the bracket [A] ( ×3).
37
5. Remove the connector ( ×1).
PCB Main Ass'y
• Require the software adjustment, When replacing the PCB Main Ass'y ( p.76). Please do the
"Copying of all data", before removing the PCB Main Ass'y.
1. PCB Main Ass'y ( p.36).
2. Remove the PCB Network ( ×6)
PCB Network
• Keep the PCB Network away from conductive materials such as metal.
38
Parts Replacement
1. PCB Network ( p.38).
• When assembling the main board, align the position of the PCB Main Ass'y and PCB Network on-
board connectors and press the portion marked [A] to fasten them securely.
Lamp Fan
1. Rear Panel and Speaker ( p.36).
39
2. Remove the Lamp fan unit ( ×2).
3. Remove the Lamp fan ( ×2).
• When assembling the lamp fan, pay careful attention to where the bracket is inserted.
40
Parts Replacement
OPT Base
• After replacing the OPT Base, Require the Software adjustment and Adjustment of the optical axis.
2. Remove the Lens holder (top) ( ×4).
3. Remove the OPT Base ( ×2).
41
Assembling the lens holder (top)
1. Press the latch portion to remove zoom lever [A] and focus lever [B].
• The zoom and focus levers use the same parts. These parts can be used interchangeably.
2. Place the lens cover over the OPTBase and screw it into place.
[A] : Zoom ring
[B] : Foucus ring
• Before placing the lens cover, align the zoom and focus rings with the center of the optical
unit.
42
Parts Replacement
3. Align the protrusion of the zoom lever with the notch on the zoom ring.
4. With the lever inclined on the engine side, push in the lens side until you hear it snap.
43
5. In the same way, install the focus lever.
IRIS Unit
44
Parts Replacement
2. Remove the barrier ( ×2).
3. Remove the IRIS unit ( ×2).
• When removing or installing the IRIS Unit, be careful not to damage the Integrator.
PS-Converter
1. Remove the IRIS unit ( p.44).
45
2. Remove the Integrator unit ( ×1).
3. Remove the PS converter ( ×1).
LCD Fan 1
1. Remove the Lamp fan ( p.39).

2. Remove the OPT Base ( p.41).
3. Remove the IRIS unit ( p.44).
46
Parts Replacement
4. Remove the Engine unit ( ×4).
5. Remove the Lens holder (bottom) ( ×2).
6. Remove the duct ( ×3).
47
7. Remove the LCD fan unit ( ×4).
8. Remove the LCD fan ( ×2).
LCD Fan 2
1. Remove the LCD fan unit ( p.46).
2. Remove the LCD fan 2 ( ×2).
48
Parts Replacement
PCB Remocon
2. Remove the PCB remocon [A].
• When assembling the board, properly insert the PCB Remocon into the notch.
49
Intake Temp Sensor
2. Remove the intake temp sensor [A] ( ×1).
Exhaust Temp Sensor
2. Remove the Exhaust temp sensor ( ×1).
50
Parts Replacement
Exhaust Fan
1. Remove the Exhaust temp sensor ( p.50).
2. Remove the Exhaust fan cover ( ×2).
51
3. Remove the Exhaust fan.
4. Remove the rubber buffer.
• The rubber buffer is reused when replacing parts. Handle it carefully.
Thermostat

2. Remove the Exhaust fan cover ( p.51).
52
Parts Replacement
5. Remove the barrier.
53
6. Remove the bracket ( ×2).
7. Remove the pin [A] and Thermostat.
• When assembling the projector, position the print side of the Thermostat to face you.
• Firmly insert the pin all the way.
54
Parts Replacement
PSU Fan
1. Remove the Exhaust fan cover ( p.51).
55
3. Remove the PSU fan [A].
Power Supply-Ballast
1. Remove the PSU Fan ( p.55).
2. Remove the Power supply-ballast ( ×3, ×2).
Power Supply-DC
56
Parts Replacement
2. Remove the Power Supply-Ballast ( p.56).
57
5. Remove the barrier.
8. Remove the Power supply-DC ( ×4 ×1).
58
Parts Replacement
Bottom Cover

2. Remove the Thermostat ( p.52).
3. Remove the Power supply-DC ( p.56).
59
Replacement of Optical Parts

Adjustments needed after the replacement of parts are as specified in the table below.
: Adjustment needed
: Need checking
Disassembly/replacement of parts
Adjustment parts Polarizing parts

OPT BASE
R G B
RL2 adjustments
CLG adjustments
CLB adjustments
POLARIZER R SASSY
POLARIZER G SASSY
POLARIZER B SASSY
Polarizer-B
1. Remove the PCB Main Ass'y ( p.38).
60
2. Remove the Polarizer-B [A] ( ×1).

[B] : Make sure to note the direction in which the Polarizer-B is set in the holder. You will notice a
mark in the area enclosed by the blue circle in the figure.
Polarizer-G
PJ X5360N
2. Remove the Polarizer-G [A] ( ×1).

[B] : Make sure to note the direction in which the Polarizer-G is set in the holder. You will notice a
PJ WX5350N
61
2. Remove the Filter (G) [A] ( ×1).
3. Remove the Polarizer-G [A] ( ×1).
• Polarizer-G No need to adjust filter.

• Insertion and removal of the polarizing plate is the same as PJ X5360N.
62
Polarizer-R
2. Remove the Polarizer-R [A] ( ×1).

[B] : Make sure to note the direction in which the Polarizer-R is set in the holder. You will notice a
Optical Parts Adjustment
Adjustments needed after the replacement of polarization plates.
63
Adjusting and fixing parts
PJ X5360N
[A] : RL2
[B] : RL2 Fixing screw
[C] : Polarization plate (R)
[D] : Polarization plate fixing screw (R)
[E] : Polarization plate (B)
[F] : Polarization plate fixing screw (B)
[G] : CLB
[H] : CLB fixing screw
[I] : CLG
[J] : CLG Fixing screw
[K] : Polarization plate (G)
[L] : Polarization plate fixing screw (G)
64
PJ WX5350N
[A] : RL2
[B] : RL2 Fixing screw
[C] : Polarization plate (R)
[D] : Polarization plate fixing screw (R)
[E] : Polarization plate (B)
[F] : Polarization plate fixing screw (B)
[G] : CLB
[H] : CLB fixing screw
[I] : CLG
[J] : CLG Fixing screw
[K] : Polarization plate (G) / Filter (G)
[L] : Filter (G) fixing screw
[M] : Polarization plate fixing screw (G)
Adjustment of the optical axis (Shadow adjustment)
If the projection test ( Shadow adjustment flow) succeeds after the Polarization plates are replaced,
there is no need to perform Shadow Adjustment.
65
[A] : To FAN POF2 (3P)

[B] : To TH-I PWB (2P)
[C] : To FAN POF1(4P)
[D] : To R/G/B LCD (40P)
[E] : To BS(5P)
[F] : To FAN POF5 (3P)
[G] : To TH-E (2P)
[H] : To FAN POF4 (4P)
[I] : To PCB Shutter (3P)
[J] : To PS (16P)
[K] : THERMOSTAT
[L] : To FAN POF3 (4P)
[M] : Turn the lamp switch ON. (Maintain the ON state by means of an adhesive tape.)
[N] : To IRIS Unit
* Refer to “Special Tools”.
66
2. Install the extension connectors and Thermostat on the PCB Main Ass’y that has been
dislodged.
3. Connect the respective connectors of the set with the extension connector PWB.
EXPERT (Test Pattern)
67
Test Pattern (Display)
4. Start the set. Display an internal pattern (all-white signal).

(Set the machine to EXPERT or SERVICE mode, then select [SETUP] to display [TEST
PATTERNDISPLAY].)
5. Make shadow adjustments.
6. After the completion of adjustments, recover the original status.
Shadow adjustment flow
68
Handling of margin in shadow adjustment

During shadow adjustment, adjust the margin so that it is balanced vertically and horizontally. If
adjustments are carried out from the LCD panel, this margin cannot be seen directly. Therefore, try to
move the shadow until its top, bottom, right, or left part appears. By doing so, examine how much
shadow is existing vertically and horizontally. Stop moving the shadow where its margin seems to be
well balanced.
69
[A] : Shadow in vertical direction

[B] : Shadow in vertical direction
Neutral setup position for each adjuster block
• CLG
Vertical :
The holder (CLG) shall be positioned at the height of two spacers (RL2) T1.0.
Horizontal :
Bosses of Cover (OPT) are located in the right and left holder (CLG) holes, each in the center
position.
• RL2
Vertical :
The holder (RL2) is held at the height of only one spacer (RL2) T1.0.
Horizontal :
Bosses of Cover (OPT) are located in the right and left holder (RL2) holes, each in the center
position.
• CLB
Vertical :
The holder (CLB) shall be positioned at the height of two spacers (RL2) T1.0 and one spacer (RL2)
T0.5.
Horizontal :
Bosses of Cover (OPT) are located in the right and left holder (CLB) holes, each in the center
position.
Operation of each adjusting part (see “Adjusting and fixing parts”)
CLG adjustment
70
[A] : Handle part of the holder (CLG)

[B] : Spacer (RL2)
[C] : Fixing screw
Vertical direction:
1. Loosen the CLG fixing screw (in 1 position) sufficiently.
2. Change the spacer (RL2) thickness and adjust the shadow margin so that it is vertically equalized.
Arrange the spacer so that its total quantity can be reduced.
Horizontal direction:
1. Hold the handle part of the holder (CLG) by hand and move the holder to the right and left in order
to adjust the shadow margin so that it is horizontally equalized.
2. After adjustments, fix the CLG fixing screw (1 position).
The tightening torque shall be 0.35 ± 0.05N•m.
RL2 adjustment
[A] : Spacer (RL2)

[B] : Handle part of the holder (RL2)
[C] : Fixing screw
Vertical direction:
1. Loosen the RL2 fixing screw (1 position) sufficiently.
71
2. Change the spacer (RL2) thickness and adjust the shadow margin until it is vertically equalized.
Arrange the spacer so that its total quantity can be reduced.
1. Hold the handle part of the holder (RL2) by hand and move the holder to the right and left in order
to adjust the shadow margin so that it is horizontally equalized.
2. After adjustments, fix the RL2 fixing screw (1 position).
CLB adjustment
[A] : Spacer (RL2)

[B] : Handle part of the holder (CLB)
[C] : Fixing screw
Vertical direction:
1. Sufficiently loosen the CLB fixing screw (1 position).
2. Change the thickness of the spacers (RL2) and make adjustments so that the shadow margin
becomes uniform vertically. Try to decrease the number of spacers.
1. Move the top section of the holder (CLB) to the right and left by hand. Make adjustments so that the
shadow margin becomes uniform horizontally.
After the completion of adjustments, fasten the CLB fixing screw (1 position).
Shadow adjustment for each color
• Vertical shadow adjustment for G and R
Move the holder (CLG) vertically and eliminate the vertical shadow. (Equally balanced in vertical
directions)
72
(Make adjustments until the portions in magenta color are eliminated vertically and uniformly in the
projector screen.)
• Horizontal shadow adjustment for G and R
Move the holder (CLG) horizontally and eliminate the horizontal shadow. (Equally balanced in
horizontal directions)
(Make adjustments until the portions in magenta color are eliminated horizontally and uniformly in
the projector screen.)
• Vertical shadow adjustment for B
Move the holder (CLB) vertically and eliminate the vertical shadow. (Equally balanced in vertical
directions)
(Make adjustments until the portions in yellow color are eliminated vertically and uniformly in the
projector screen.)
• Horizontal shadow adjustment for B
Move the holder (CLB) horizontally and eliminate the horizontal shadow. (Equally balanced in
(Make adjustments until the portions in yellow color are eliminated horizontally and uniformly in the
projector screen.)
• Horizontal shadow adjustment for R
Move the holder (RL2) vertically and eliminate the vertical shadow. (Equally balanced in vertical
directions)
(Make adjustments until the portions in cyan color are eliminated vertically and uniformly in the
projector screen.)
• Vertical shadow adjustment for R
Move the holder (RL2) horizontally and eliminate the horizontal shadow. (Equally balanced in
(Make adjustments until the portions in cyan color are eliminated horizontally and uniformly in the
projector screen.)
Adjustment of the polarization plate (Contrast adjustment)
Outlined description of adjusting work
73
[A] : To FAN POF2 (3P)

[B] : To TH-I PWB (2P)
[C] : To FAN POF1(4P)
[D] : To R/G/B LCD (40P)
[E] : To BS(5P)
[F] : To FAN POF5 (3P)
[G] : To TH-E (2P)
[H] : To FAN POF4 (4P)
[I] : To PCB Shutter (3P)
[J] : To PS (16P)
[K] : THERMOSTAT
[L] : To FAN POF3 (4P)
[M] : Turn the lamp switch ON. (Maintain the ON state by means of an adhesive tape.)
[N] : To IRIS Unit
* Refer to “Special Tools”.
74
1. Install the extension connectors and Thermostat on the PCB Main Ass’y that has been
dislodged.
2. Connect the respective connectors of the set with the extension connector PWB.
3. Start the set. Display an internal pattern (all-black signal).

(Select Install and Setup on the menu screen and set the background at Black Background.)
4. Adjust the polarization plate.
5. After the completion of adjustments, return the set to its original state. Method of
adjustment (see “Adjusting and fixing parts”)
75
Electrical Adjustment
Adjustments needed after the replacement of Main PWB is as specified in the table below.
: Adjustments needed
: Data Read/Write
: This is needed, depending on the situation.
PCB Main
OPT Base
Ass’y
Data writing
Data for each model
EDID Data
Serial number and Model number
Data Read/Write
Flicker Data
VT Data
Uniformity Data
All Data
Color Correction Data
Wall Collor Data
Usage Time Data
Flicker adjustment
Floor
Ceiling
Description of adjustment items

• Version up field Data for each model (PJ Upgrader)
Writes data, such as the model name, used to identify the model.
If the value is incorrect. an image from the PC may not be displayed correctly (for example,
may be ghosted).
• Data for each model (PJ Upgrader 2)
76
Writes BIOS data, Firmware, Firm and data for each CPU, set device (IC) values, a
temperature table for cooling, and adjusted VT values.
• EDID Data
Writes Model-related data for each model used for communication with a PC.
If this value is incorrect, the PC may be unable to recognize a XGA/WXGA mode.
• Serial number and Model number
Writes the serial number and model name of the product.
• Flicker adjustment
Writes the electrical characteristic values of each individual OPT Base.
Procedures for the replacement of the PCB Main Ass’y
Outline of adjustment procedules

Before the replacement of PCB Main Ass’y.
1. Copying of all data

After the replacement of PCB Main Ass’y
1. Data writing for each model is carried out

Software : PJUpgrader2vupf, PJUpgrader2
2. Writing of copied All Data
Software : PC control software for service
3. EDID data writing is carried out
Software : EDID Writer
4. Data writing for Serial number and Model number
Software : SN WRITER
• When all data cannot be copied

1. Data writing for each model is carried out (PJUpgrader2vupf, PJUpgrader2)
2. Flicker adjustments, Usage Time setup (PC control software for service)
3. EDID data writing is carried out (EDID Writer)
4. Data writing for Serial number and Model number (SN WRITER)
77
PC control software for service

Outline of software descriptions
This is the PC control software for servicing adjustments to be conducted during the replacement of
the PCB Main Ass’y or LDC panel (OPT BASE).
This software makes it possible to perform the following adjustments:
• Adjustment of Flicker
• Modification of usage time for the Usage Time (Lamp, Filter, Panel, and Projector)
• READ/WRITE of factory ADJ data (Flicker, VT, Uniformity, Color Correction, Wall Color) and
Usage Time data
Personal computer setting intended to obtain the adjusting pattern screen outputs
• Personal computer’s resolution, frequency, and the No. of colors
Make settings for VESA XGA (1024 ×768) 60Hz, high color (16 bits) or above.
• Method of adjusting pattern screen display
The available Test Patterns are all built into the projector.
Software installation procedures
This software is composed of the following items:
• Service adjusting software
• Various DLL files
Follow the instructions below to install the files on the PC.
1. Copy all files into any folder.

Starting and ending methods for adjustments
<Method of adjustment starting>
78
1. Assure a condition that PJ and PC are connected through a serial cable and start the
service adjustment software.
2. Click [Setup] button to open the Setup window.
79
3. Select the COM port connected to the PJ in the [Port] box. Set the baud rate match
the setting of the PJ. Press [Return] button when the setting is completed.
4. Click “Adjust Start” to start initial data reading.

* Each adjusting button will be enabled when models are correctly identified.
<Method of adjustment ending>
When the adjustment described below, from the procedure “Replacement of the PCB Main Ass’y”,
“Replacement of the OPT BASE” and “Miscellaneous” is done, click [Adjust End] button.
* When adjustments of another set are further intended, operation should be started with [Adjust
Start].
* If you try to adjust another set without making [Adjust End], there will be an error as a result of
model discrimination.
* Click [Close] button to terminate the program.
Copying and Writing All Data
<All Data copying>
80
Click [Data] button of the service software with the PJ Power in standby to open the Data window.
According to (1) and (2) below, follow the steps of All Data Read / Write.
All Data mentioned here denote the respective factory adjusting data (Flicker, VT, Uniformity, Color
Correction, Wall Color), and Usage Time.
81
1. All Data Read

Read the PCB Main Ass’y data currently used before replacement and save them in a file.
Check mark the [All data], and click [Read] button. Name the file and save.
The procedure is done when a message box “It completed.” is displayed.

* In a certain faulty state, data cannot be saved. In such a case, follow the steps of
[Miscellany].
<All Data writing>
82
1. All Data Write

After exchanging PCB Main Ass’y, click [Write] button to select the saved file.
When a message “Please Power Off (Standby state).” is displayed, make sure that the PJ
Power is in standby, then click [OK] button.
The procedure is done when a message box “It completed.” is displayed.
83
* When executing data writing, [Data] indicated in the main window turns to bold text.
Adjustment of Flicker
Click [Flicker] button of the service software to open the Flicker Adjust window.
Make Flicker adjustments according to (1) ~ (3) below.
1. Adjustment start
Keeping the PJ power supply turned ON, maintain the condition of aging for five minutes.
84
2. Adjustment of Floor
Check [Floor].
Display Red raster signal by clicking [Test R] button in the [Test Pattern] box. Adjust R-scroll
bar so that the flicker in the middle of the window becomes smallest.
Display Green raster signal by clicking [Test G] button in the [Test Pattern] box. Adjust G-scroll
85
Display Blue raster signal by clicking [Test B] button in the [Test Pattern] box. Adjust B-scroll
When flicker adjustment is done, click [SET] button in the [Data] box to write the adjusted
value.
* When displaying Test pattern, in case flicker is not clearly displayed because of the
horizontal lines, click [Test R/G/B] button a few times to clear the lines.
86
3. Adjustment of Ceiling
Check [Ceiling].
Display Red raster signal by clicking [Test R] button in the [Test Pattern] box. Adjust R-scroll
Display Green raster signal by clicking [Test G] button in the [Test Pattern] box. Adjust G-scroll
Display Blue raster signal by clicking [Test B] button in the [Test Pattern] box. Adjust B-scroll
When flicker adjustment is done, click [SET] button in the [Data] box to write the adjusted
value.
* When displaying Test pattern, in case flicker is not clearly displayed because of the
horizontal lines, click [Test R/G/B] button a few times. It clears the lines.
* When adjustment for each Floor and Ceiling is done ([SET] is clicked), the Floor / Ceiling
characters turn to red.
* To restore the data to the state before the adjustment, click [RESET] button. The data will
restore to the initial setting, and the characters return to black.
* The value displayed by the side of the scroll bar indicates; the original value in the left side
of the arrow, the current value in the right side of the arrow.
* The data adjusted with the scroll bar is temporary data. For the PJ to store the data, click
[SET] button to write in Flash ROM.
* To adjust the machine, you do not need to turn the it upside down.
Usage Time Setup
• If the present Usage Time for the Lamp / Projector is different from the actual Usage Time, the
following setup is made to recover the correct Usage Time.
• When Usage Time Read / Write is carried out at the time of PCB Main Ass’y replacement, the
correct Usage Time is also copied for the Lamp / Projector. Therefore, no more setting is
required.
• However, this function should not be used unless the correct Usage Time is known.
87
Click [Usage Time] button of the service software with the PJ Power in standby to open Usage
Time Setting window.
Make Usage Time setup according to (1) below.
88
1. Setting
Select a type of Usage Time to be changed in the [Change Usage Time].
Set time using the scroll bar, then click [SET] in the Data Box.
When a message [Please Power Off (Standby state).] is displayed, make sure that the PJ
Power is in standby, then click [OK] button.
Using scroll bars, adjust [Hours] and remaining [%] for Lamp Usage Time, and [Hours]
for Usage Time.
* When Usage Time is changed, the changed time will be displayed in the editor below.
* To restore the time, click [RESET] button. It restores to the initial data.
* When changing Usage Time, [Usage Time] indicated in the main window turns to bold
text.
2. Select a type of Usage Time to be changed in the [Change Usage Time]. Set time
using the scroll bar, then click [SET] in the Data Box.
Using scroll bars, adjust [Hours] and remaining [%] for Lamp Usage Time, and [Hours]
for Usage Time.
* When Usage Time is changed, the changed time will be displayed in the editor below.
89
* To restore the time, click [RESET] button. It restores to the initial data.
Error messages
• “TIME OUT (ACK) !”
This is a communication error in conjunction with the PJ.
Check the Serial Port Number, BaundRate, and whether the PJ main Power is turned ON.
• “TIME OUT (Data) !”, “RsRead Error,” , “Data Send Error!!”, “DATA READ ERROR”, “Model
check Error (Data Read)!!”
This is a communication error in conjunction with the PJ.
Check the connection, and error occurrence in the PJ, then retry.
In case it occurs 2 or 3 times consecutively, reboot the PC.
• “Comm Open Error”
This is a failure in opening the serial port.
Check the Serial Port Number.
Make sure that there is no other application using the same Serial Port.
• “TIME OUT (Comm Close Error) !”, “Comm Close Error”
This is a failure in closing the serial port.
Confirm if there is any application that occupies the serial port.
• “File format error”, “Address error”
The data format of the file specified when executing data writing from the file is not correct.
Make sure that it is a file read in PJ X5360N/PJ WX5350N.
• “ACK Error!!”
Check the status of the PJ, and retry.
* For instance, you may have done an operation with Power OFF, which should have been
done with Power ON.
If not recovering from this error after operating the above, the PJ may be in trouble.
• “Model name error!!”
The target PJ is not PJ-X5360N or PJ-WX5350N.
• “Model check Error (2)!!”
The current target PJ is not the one executed [Adjust Start].
Restart from [Adjust Start], in case adjusting current target PJ.
• “Comparison error”
The data is not successfully written. Retry writing.
90

If not recovering from this error after operating the above, the PJ may be in trouble.
Model-Specific Data Writing Procedure

Model-specific data writing procedure
1. Model-related data for each model

Writing software : PJUpgrader2.exe
File name to be written : *********_mdata.bin
2. Initial setting of writing software
[COM port] : Set the COM port of used PC.
[Baud rate] : Match the setting of the PJ.
Operation Procedure
Prior to operation, install the writing software (PJUpgrader2.exe) and copy the files of the writing
model (*****_mdata.bin).
Writing of model-related data for each model
RTB 10
Corrected
1. Connect PJ and PC with an USB cable.

2. Turn the power ON, pressing the [MENU] and [EXIT] keys of the main unit
simultaneously. (AC source turned on)
91
3. Release the [MENU] and [EXIT] keys when the Power LED blinks in green.
92
4. Start up PJUpgrader2.exe previously installed.
5. Press [choose….] button to select the file (*****_mdata_******.bin) to be written.

6. Check that the set and PC are properly connected each other, then press [Flash]
button.
Message "Do you start flash write?" is displayed.
7. When [Yes(Y)] button is pressed, writing is started.
(Progress bar showing writing situation is displayed.)
8. Message "Write Finished!" is displayed, when completed. Press [OK] button to finish
the operation.
93
9. Turn the Power OFF for the PJ main unit.

10. Disconnect the USB cable.
Error Messages
• Attestation failure. (-1001)
When rewriting the version up field, it is required to set the projector in writing only mode in
advance.
• The model information of the file conflicts with that of the connected projector. (-1002)
Check the projector connecting to the selected file.
The projector connected is not that the selected file can write for.
Procedure for rewriting EDID data

Outline software descriptions
This is PC control software to rewrite EDID data of PCB Main Ass’y supporting PJ X5360N/
WX5350N.
Equipment to be used and environment
Equipment to be used
• EDID rewriting software
EDIDWrite.exe
• EDID data (Digital) ("***" in the file name denotes the version.)
X5360N_EDID_HDMI_V***
WX5350N_EDID_HDMI_V***
• EDID data (Analog) ("***" in the file name denotes the version.)
X5360N_EDID_DSUB_V***
WX5350N_EDID_DSUB_V***
• PC
A Windows XP / 2000 operable PC, which enables a serial cable and RGB (analog) video
connection with the PJ.
• Serial cable
D-SUB9pin-D-SUB9pin, Cross (reverse) cable
• RGB video cable
D-SUB15pin
94
Software installation procedures
1. Installing EDIDwriter
Copy all files of “EDIDwriter” into any folder.
2. Installing EDIDdata
Copy each EDID data to any folder, and execute.
Rewrite procedure
* Make sure to follow the procedure below to rewrite the data.
• After exchanging PCB Main Ass’y, first adjust PCB Main Ass’y. (PCB Main Ass’y adjustment:
Use PC control software for service.)
1. Rewrite HDMI terminal EDID.
2. Rewrite D-SUB terminal EDID.
Rewriting HDMI terminal EDID
RTB 10
Corrected
95
1. Initial setting
Turn the Power OFF for the PJ main unit. (AC source turned on)
Connect the PJ and the PC with a serial cable, referring to "2. Equipment to be used and
environment" Then activate "EDIDwriter".
• Mode
Select "Flash".
• Port
Select the corresponding Com Port for the target PC.
• Baud Rate
Match the setting of the PJ.
96
2. Selecting a writing file

Click "Choose.." button to select the file.
* Select HDMI EDID data from File name “yyyy_ EDID_HDMI_V***.bin”. (yyyy:Model,
xxx:version).
• Comparison Table of Model Names and EDID File Names of HDMI
Model Name EDID File Name
PJ-X5360N X5360N_EDID_HDMI_V***.bin
PJ-WX5350N WX5350N_EDID_HDMI_V***.bin
* The asterisks *** of the fine name denote a version.

3. Transferring to Data Writing Mode
Make sure that the PJ is in ON state.
97
4. Rewriting data
Make sure that the PJ and the PC are properly connected, and then click "Flash" button.
Rewriting HDMI terminal EDID is started.
When writing is completed, the message "Write Finished!" will be displayed.
Click "OK" button to finish the procedure.
Rewriting D-SUB terminal EDID
98
1. Initial setting
Turn the Power OFF for the PJ main unit. (AC source turned on)
Connect the PJ and the PC with a RGB cable, referring to "2. Equipment to be used and
environment". Then activate "EDIDwriter".
• Mode
Select "Flash".
• Port
Set "DDCAUTO".
99
2. Selecting a writing file

Click "Choose.." button to select the file.
* Select D-SUB EDID data from File name “yyyy_ EDID_DSUB_V***.bin”. (yyyy:Model
series name, xxx: version)
• Comparison Table of Model Names and Analog EDID File Names
Model Name EDID File Name
PJ-X5360N X5360N_EDID_DSUB_V***.bin
PJ-WX5350N WX5350N_EDID_DSUB_V***.bin
* The asterisks *** of the fine name denote a version.

3. Transferring to Data Writing Mode
Turn the PJ Power ON, and transfer to Service Mode.
Moving to another service mode
The [ENTER PASSCODE] menu is displayed when the keys are pressed in the order of [Help]
[Enter] [Help] [Enter] [Help] [Enter] [Menu] for 3 seconds.
100
Press the select keys in the order of [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [Enter].

Press the [Menu] key to obtain a menu display and confirm that [SERVICE] is displayed in
lower part of the menu.
4. Rewriting data
Make sure that the PJ and the PC is properly connected, and then click "Flash" button.
It is not necessary that the PC image is displayed on the PJ at this time.
When writing is completed, the message "Write Finished!" will be displayed.
Click "OK" button to finish the procedure.
When the PJ is equipped with multiple D-SUB input terminals (Computer IN), execute data
rewriting for each terminal.
In the case of failure in EDID writing, such as the PJ being not in service mode or the like, there
is a display of “The difference was found to address 0x?? bin=0x?? edid=0x??”.
Error message
101
The serial port has failed to open.

Check whether any available serial port has been selected.
There is no response from the PJ.

Check whether the PC and the PJ are connected through a serial cable.
There was a Nack response from the PJ.

Check the condition of PJ power supply and the baud rate.
Writing in the EDID of HDMI is impossible from the DDC/CI board.

Select the serial port.
102
The PJ is not found.

Check whether the PC and the PJ are connected through an RGB cable.
A wrong model is specified.

Check the model.
Procedure for writing of a serial number and a model number

Software installation
103
Decompress snwriter000002.zip; and execute the established set-up.exe to install it in the PC.
(For the destination folder for installation, either half-size or full-size font characters are
acceptable.)
Writing of a serial number and a model number
1. Connect the Projector to computer through an RS-232C cable (Reverse) (D-SUB9pin -

D-SUB9pin). Turn on the power supply of the Projector.
2. Click “ ” that is saved in the directory (C:¥Program Files¥Projector Tools
¥SN WRITER¥).
3. In the specified format, the model number and the serial number are entered in the
column of [A]. When the “Write” button is pressed, these data are transferred to the
projector and serial number writing is completed.
Specified format :
Attach the asterisks (“*”) to the head and the tail.
Provide a space between the model number and the serial number.
• After the completion of writing, no verification is performed. Therefore, press the “Read”
button separately to confirm the result of writing.
104
Data readout
The data (model number and serial number) written in the projector are read out.
When the “Read” button is pressed, the data read out of the projector are displayed in Column [B]
in the specified format.
In regard to “baud rate” that is indicated in the above-mentioned screen, make confirmation on the
menu screen specified below.
105
Procedures for the replacement of the OPT Base
1. Flicker adjustments ( PC control software for service)
106
Firmware Upgrade
A LAN cable is needed to upgrade the firmware.
Before upgrading the firmware, make sure to prepare the following:
• LAN cable
• Notebook PC (on which Internet Explorer 6.0 or later is installed)
Upgrading the firmware
1. Connect the PC to the projector via a wired or wireless LAN.

* You can use PING to check whether the PC is successfully connected to the LAN.
2. Select [MENU] [INFO.] [WIRED LAN] or[WIRESS LAN]to check the IP address.
3. Place the projector in standby mode.
* On the projector, set [STANDBY MODE] to [NORMAL].
4. Start Internet Explorer and open the "http://xxx.xxx.x.xx/upload.html" page.
* Replace xxx.xxx.x.xx with the IP address that was confirmed in Step 2.
5. When the "Projector Update" page appears, press the [Browse] button.
107
6. Select the file and press the [UPDATE] button.
7. When the confirmation dialog box appears, press the [OK] button.
8. When the message "File written successfully" appears in the history section, press the
[REBOOT] button to restart the projector.
9. To update multiple files, repeat steps 5 to 7 for each file you want to update.
10. Do not turn off the projector or disconnect the LAN cable before the update is complete.
Otherwise, the projector may not restart.
108
Functional Test
Functional Test
Connecting a Computer
Signals supported by Plug & Play (DDC2)
INPUT
Computer 1 In Computer 2 In HDMI
analog analog digital
Yes Yes Yes
[A] : A commercially available USB cable (compatible with USB 2.0 specifications)
[B] : HDMI cable (not supplied), Use High Speed HDMI® Cable.
[C] : Stereo mini-plug audio cable (not supplied)
[D] : Computer cable (VGA) (supplied)
109
To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially
available distribution amplifier if connecting a signal cable longer than the cable supplied.
• For Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac’s
video port.
• When [VIEWER], [NETWORK], or [USB DISPLAY] is selected for [INPUT], sound from the
Computer 2 Audio In mini jack will be output through the speaker.
• Select the source name for its appropriate input connector after turning on the projector.
Input button on the projector

Input connector Button on the remote control
cabinet
Computer 1 In COMPUTER1 Computer 1
Computer 2 In COMPUTER2 Computer 2
HDMI In HDMI HDMI
USB (PC) USB DISPLAY USB Display
• An image may not be displayed correctly when a Video or S-Video source is played back via a
commercially available scan converter.
• This is because the projector will process a video signal as a computer signal at the default setting.
In that case, do the following.
• * When an image is displayed with the lower and upper black portion of the screen or a dark
image is not displayed correctly : Project an image to fill the screen and then press the Auto Set
button on the remote control or the projector cabinet.
• When Viewing a DVI Digital Signal

• Use a DVI-to-HDMI cable compliant with DDWG (Digital Display Working Group) DVI
(Digital Visual Interface) revision 1.0 standard. The cable should be within 197"/5 m long.
• Turn off the projector and the PC before connecting the DVI-to-HDMI cable.
• To project a DVI digital signal: Connect the cables, turn the projector on, then select the HDMI
input. Finally, turn on your PC. Failure to do so may not activate the digital output of the
graphics card resulting in no picture being displayed. Should this happen, restart your PC.
110
Functional Test
• Some graphics cards have both analog RGB (15-pin D-Sub) and DVI (or DFP) outputs. Use of
the 15-pin D-Sub connector may result in no picture being displayed from the digital output of
the graphics card.
• Do not disconnect the DVI-to-HDMI cable while the projector is running. If the signal cable
has been disconnected and then reconnected, an image may not be correctly displayed.
Should this happen, restart your PC.
• HDMI input signal

• Disconnecting and connecting the HDMI cable may result in no picture being displayed from the
HDMI equipment while the projector is running.
• Should this happen, select the HDMI input again.
• <Two ways to select the HDMI input>
• Press the HDMI button on the remote control.
• Press the Menu button on the projector cabinet, then select [HDMI] from [INPUT].
111
Connecting an External Monitor
[A] : Computer cable (VGA) (not supplied)

[B] : Computer cable (VGA) (supplied)
[C] : Stereo mini-plug audio cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the
computer analog image you’re projecting.
• Daisy chain connection is not possible.

• When audio equipment is connected, the projector speaker is disabled.
112
Functional Test
Connecting a DVD Player or Other AV Equipment
Connecting Video/S-Video Input
[A] : S-Video cable (not supplied)

[B] : Video cable (not supplied)
[C] : Audio cable (not supplied)
[D] : Audio equipment
[E] : Audio cable (not supplied)
• Select the source name for its appropriate input connector after turning on the projector.

cabinet
VIDEO IN VIDEO Video
S-VIDEO IN S-VIDEO S-Video
113
• The Audio In L and R jacks (RCA) are shared between the Video and S-Video inputs.
• Refer to your VCR owner’s manual for more information about your equipment’s video output
requirements.
• An image may not be displayed correctly when a Video or S-Video source is played back in fast-
forward or fast-rewind via a scan converter.
Connecting Component Input
114
Functional Test
[A] : Stereo mini plug - to - RCA audio cable (not supplied)

[B] : Monitor cable Stereo mini plug - to - RCA able Mini D-sub 15P-BNC (not supplied)
[C] : Conversion adapter BNC-pin (not supplied) To Y/Cb/Cr output Green(Y)/Blue(Cb)/Red (Cr)
[D] : Audio cable (not supplied)
[E] : Audio Equipment
[F] : DVD player
A component signal will be automatically displayed. If not, from the menu, select [SETUP]
[OPTIONS(1)] [SIGNAL SELECT] [COMPUTER1] or [COMPUTER2], and then place a check
mark in the Component radio button.
Select the source name for its appropriate input connector after turning on the projector.

cabinet
COMPUTER 1 IN COMPUTER 1 Computer 1
COMPUTER 2 IN COMPUTER 2 Computer 2
• Refer to your DVD player’s owner’s manual for more information about your DVD player’s video
output requirements.
Connecting HDMI Input
You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook
type PC to the HDMI In connector of your projector.
• The HDMI In connector supports Plug & Play (DDC2B).
115
[A] : HDMI cable (not supplied) Use High Speed HDMI® Cable.
[B] : Audio cable (not supplied)

cabinet
HDMI IN HDMI HDMI
• For users of audio video equipment with an HDMI connector:

• Select “Enhanced” rather than “Normal” if HDMI output is switchable between “Enhanced” and
“Normal”.
• This will provide improved image contrast and more detailed dark areas.
• For more information on settings, refer to the instruction manual of the audio video equipment to be
connected.
116
Functional Test
• When connecting the HDMI In connector of the projector to the DVD player, the projector’s video
level can be made settings in accordance with the DVD player’s video level. In the menu select
[HDMI SETTINGS] [RGB INPUT RANGE] and make necessary settings.
• If the HDMI input sound cannot be heard, in the menu select [HDMI SETTINGS] [AUDIO
SELECT] [HDMI].
Connecting to a Wired LAN
The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN
cable.
To use a LAN connection, you are required to set the LAN on the projector menu. Select [APPLICATION
MENU] [NETWORK SETTINGS] [WIRED LAN].
Example of wired LAN connection
[A] : Server
[B] : Hub
[C] : LAN cable (not supplied) (Use a Category 5 or higher LAN cable.)
117
Input signals
Signal level
RGB signal 0.7Vp-p/75
1.0Vp-p/75 (Signal Y)
Component signal
0.7Vp-p/75 (Cb/Cr, Signal Pb/Pr)
VIDEO signal 1.0Vp-p/75
1.0Vp-p/75 (Signal Y)
S-VIDEO signal
0.286Vp-p/75 (Signal C burst level)
Sync signal TTL Level (Positive/Negative polarity)/ 1k
Audio signal 0.5Vrms/22k or more
RGB signal frequencies
Horizontal sync frequency 15-100kHz
Vertical sync frequency 50 - 120Hz
Maximum resolution UXGA (1600*1200)
HDMI digital signals
Maximum resolution WSXGA+ (1680*1050) @60Hz
Component signals
• 525i, 625i, 480p, 576p (DVD output signal)

• 720p, 1080i, 1080p (HDTV signal)
Video input color system
• NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM
118
5. Troubleshooting
LED Display
Indicator Messages
Power Indicator
Indicator Condition Projector Condition Note
Off The main power is off
Blinking Blue (short flashes) The projector is getting ready to turn on. Wait for a moment.
light Blue (long flashes) Off Timer is enabled.
Blue The projector is turned on.
[NORMAL] is selected for [STANDBY

Steady Orange
MODE]
light
[POWER-SAVING] is selected for
Red
[STANDBY MODE]
Status Indicator
Normal or Standby
Off ([POWER-SAVING] for
[STANDBY MODE])
119
5. Troubleshooting
Lamp cover error or Replace the lamp cover or lamp housing

Red (cycles of 1)
lamp housing error correctly.
The projector is overheated. Move the

Red (cycles of 2) Temperature error
projector to a cooler location.
Power unit is not working properly. Contact

Red (cycles of 3) Power error
your dealer.
Red (cycles of 4) Fan error Fans will not work correctly.
Lamp fails to light. Wait a full minute and

Red (cycles of 6) Lamp error
then turn on again.
Blinking
light [DYNAMIC Dynamic Contrast function is not working
Red (cycles of 9)
CONTRAST] error properly. Contact your dealer.
Both the built-in wired LAN and the wireless

LAN cannot be connected to the same
Orange (cycles of network at the same time.
Network conflict
1) To use both built-in wired LAN and wireless
LAN at the same time, connect them to
different networks.
Re-firing the lamp (The The projector is re-firing.

Green projector is cooling
down.) Wait for a moment.
Standby ([NORMAL] for

Green
[STANDBY MODE])
Steady CONTROL PANEL You have pressed cabinet button when

light LOCK is on. Control Panel Lock is on.
Orange
Remote control ID and projector ID are not
CONTROL ID error
matched.
Lamp Indicator
Off Normal
Blinking Lamp has reached its end of life. Lamp

Red Replace the lamp.
light replacement message will be displayed.
120
LED Display
Lamp has been used beyond its limit. The

Red projector will not turn on until the lamp is Replace the lamp.
Steady replaced.
light
[LAMP POWER] is set to [AUTO ECO] or
Green
[ECO1]
Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically
turn off the lamp with the Status indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cord after the cooling fans stop.
• Move the projector to a cooler location if the room where you are presenting is particularly too
warm.
• Clean the ventilation holes if they are clogged with dust.
• Wait about 60 minutes until the inside of the projector becomes cool enough.
121
5. Troubleshooting
Service Mode
List of functions
Function EXPERT SERVICE
VS BEGIN
CLAMP TIMING
SYNC PROTECTION UPPER
SYNC PROTECTION LOWER
VIDEO FILTER
TEST PATTERN2
COLOR UNIFORMITY
WHITE UNIFORMITY
(All white color unevenness adjustment function)
SYNCHRONIZE
REF. WHITE BALANCE
KEYSTONE CONFIGURATION
(Horizontal adjustment)
MESSAGE
CLEAR PANEL HOURS
SET UP-PING
Mode changeover
Expert mode
(For setting subcontractor: any mode that can be released to a subcontractor)
122
Service Mode
• In the state of Power ON, press each key in the order of [HELP] [ ] [ ] [HELP].
• Press the [MENU] key to display the menu and confirm that [Expert] is displayed below the menu.
Service mode
(for service)
• In the state of Power ON, press each key in the order of [HELP] [ENTER] [HELP] [ENTER]
[HELP] [ENTER] [MENU] for 3 seconds each. Then, a menu of [ENTER PASSCODE] is
displayed.
Press the select keys in the order of [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ENTER].

Press the [MENU] key to display the menu and confirm that [Service] is displayed below the menu.
How to withdraw from the mode
• If the [EXIT] key is pressed twice in the state that no menu is displayed, the original state will be
recovered.
123
5. Troubleshooting
• Recover the standby state by pressing the [POWER] key. When this action is taken, the original
status can also be recovered at the time of next starting.
Contents of display
When the service mode or the expert mode is assumed, the menu is added with the functions specified
below.
• Mode display
The present mode is displayed at the right side on the bottom of the menu screen.
• Addition of the adjusting functions to the menu top
The adjusting functions usually not displayed come to be displayed. Then, adjustments become
possible.
In the expert mode, the function for an expert menu can be selected.
In the service mode, the function for an expert menu or a service menu can be selected.
In addition, [Clear Panel Hours] is added to “Reset.”
• Modification of processing for existing functions
In the service mode, the items to be initialized are increased for the All Data Reset.
Additional functions (extract)
SETUP–EXPERT1 Tab
TEST PATTERN2
A test pattern can be set up or displayed. The setting, such as pattern, color, and level of the test
pattern to display can be changed over with PATTERN/RED/GREEN/BLUE/INVERT/LEVEL in the
test pattern items. After the test pattern setting is selected, the test pattern will be displayed, when
the DISPLAY is carried out.
Test pattern changeover and such operation are possible during test pattern display by means of a
remote control.
• Up/Down key: Test pattern changeover (Raster Cross hatch Gray Bars )
• Right/Left key: Level adjustment
• Menu: Red On/Off
• Aspect: Green On/Off
• PIC-Mute: Blue On/Off
• Enter: Invert On/Off
• EXIT: Test pattern cancel
124
Service Mode
In the gray bars, ON/OFF switching is impossible for Red, Green, Blue, and Invert.
When a test pattern is displayed in the state that no input signal is applied, Picture Management
setup is effected in the High Bright mode.
SETUP–EXPERT2 Tab
Mesage
Display or non-display of the following messages is set up:
Function error: [This function cannot be used.]
Control Panel Lock Turn On: [Keys of the main unit are now locked.]
Control Panel Lock Disable: [The key-locked main unit has been unlocked.]
Power management: [It is 3 minutes before power OFF.]
Sleep timer: [It is 3 minutes before power OFF.]
Filter Message: [It’s the time to clean the filter.]
TEMP MESSAGE: [There is unusual temperature rise in the projector. Clean the filter.]
Lamp Message: [It is time for lamp replacement. Earlier replacement is recommended according to
the Instruction Manual.]
The initial value after “All Data Reset” is ON.
Security functions
• Keyword setting only is required for security. (The memory card cannot be used.)
• The keyword is a combination of the UP, DOWN, RIGHT, and LEFT keys.
How to cancel the security functions
If the user forgets the keyword and cannot use the projector, it is necessary to make queries to the
service station to get the keyword.
For the security-canceling tool, the decoded keyword is indicated in alphanumerical characters. Since
the keyword for this model uses the up/down/right/left keys, it is necessary to decode the indicated
alphanumerical characters into such up/down/right/left keys.
When the keyword indicated by the security-canceling tool has to be transferred to the user, refer to the
next table and decode the numerals into the up/down/right/left keys.
Displayed keyword Key data sent to the user
1 UP
125
5. Troubleshooting
Displayed keyword Key data sent to the user
3 DOWN
4 LEFT
5 RIGHT
MM Viewer and Network Area
List of functions
MM function EXPERT SERVICE
Viewer – Check pattern
Network – PING
IMAGE EXPRESS UTILITY – Detailed setup
DESKTOP CONTROL UTILITY – Detailed setup
Network setup – Wireless LAN – Detailed setup

(simplified connections)
Network setup – Wireless LAN – Detailed setup (easy

access points)
Network setup – Wireless LAN – Detailed setup

(profile)
Network setup – Firewall
Network service – HTTP server
Network service – PJLink
Network service – SNMP
Network service – PC control
Application error log output
126
Service Mode
Additional Functions
Viewer – Check Pattern
The video data saved in the PJ are displayed.
Network – PING
When an address is put in the IP Address item for execution, the result is displayed in the Result
item.
To take this action repeatedly, a check mark should be put in the “Repeat” CheckBox. To suspend
this action, press the Stop button.
Image express utility – Detailed setup
Designate the IEU Port number of IEU Lite / Image (UDP) / Image (TCP) / Search / User
Management / Desktop Control.
Desk control utility – Detailed setup
• DCU No Password mode
DCU can be used without any password.
Network setup – Wireless LAN – Detailed setup (simplified connections)
• Baud rate
Baud rate is selected for simplified connections.
• Transmission output (%)
Transmission output is specified for simplified connections.
Network setup – Wireless LAN – Detailed setup (easy access points)
Transmission output is specified for easy access points.
Network setup – Wireless LAN – Detailed setup (profile)
• Mode (2.4GHz)
Mode is selected for profile connections.
• Baud rate (Mbps)
Baud rate is selected for profile connections.
Transmission output is specified for profile connections.
Network setup – Firewall
• Effective
Effective/ Non-Effective is specified.
When “Effective” is selected, all inbound packets of TCP/UDP/ICMP come to be blocked
out. An access-enabled IP address or a subnet is registered in the profile.
127
5. Troubleshooting
• Profile
Profile1 ~ Profile4 is specified.
• Subnet registration
A subnet is registered.
• Host address
A host address is registered.
• Host subnet mask
A host subnet mask is specified when a checkmark is given to the subnet being registered.
Network service – HTTP server
• Port
A port number is specified. In the case of “Initialize” operation, the initial value is recovered.
Network service – PJLink
• Port
Network service – SNMP
• Effective
Effective/ Non-Effective of SNMP is specified.
Network service – PC control setup
Application error log output
1. The following root folder is established in the USB memory.
“MM_KDMP_FOLDER”
2. The projector is set in the service mode.
3. The USB memory, where the “MM_KDMP_FOLDER” folder has been established, is inserted
in the projector.
4. An application error log output is generated in the USB memory.
128
Troubleshooting Guide
Operation check
It is possible to conduct a certain level of fault diagnosis in normal state of operation check.
Before removing the top cover, check the indicator.
Factors related to starting
129
5. Troubleshooting
Factors related to operation

These items are often caused by confusion such that the menu setup has been wrongly made.
1. The Power is not ON even though the Power switch is pressed in the standby state (POWER
LED lit in orange, and STATUS LED in green)
2. Normal video display is not presented with the COMPUTER1/COMPUTER2 (ANALOG)

input (RGB/Component).
130
* Confirmation for the Test Pattern display of the Expert Mode menu is effective as an
examination program even at the time of input entry at the Video / S-Video terminal.
Power block
If the power does not start. (Power LED is not lit)
RTB 6
This flow chart
was changed
131
5. Troubleshooting
If the power does not start. (Power LED is not blue)
For Video
The picture is not displayed correctly Com1/Com2.
132
For Audio
Does not output sound from the speaker.
133
5. Troubleshooting
Error Log
Error Log Screen Image
Displaying an error log screen
The error log screen is displayed by long-pressing the [MENU] button five seconds or more in user,
expert, or service mode.
Service Information: Page-1
User mode / Expert mode
Service mode: Display of other areas added
134
Error Log
Service Information: Page-2
User mode / Expert mode
Service mode: Display of lamp voltage added
135
5. Troubleshooting
Service Information: Reset
Not related to the menu mode
136
Error Log
Contents of Error Log (Page1) Display
* Cleared with All Data Reset from the service menu.
Status Columns
List of Phenomena caused by Power OFF due to Errors
Display
Meaning Details Possible cause
symbol
E1-1 Status LED blinking once Cover malfunction Lamp cover
E2-1 Status LED blinking twice Temperature error Bimetal error
E2-2 Status LED blinking twice Temperature error Thermal error
E3-1 Status LED blinking 3 times Power source error Nil
E4-1 Status LED blinking 4 times Fan stop Nil
E4-2 Status LED blinking 4 times Super-capacitor error Nil
Lamp failure in lighting (except

E6-1 Status LED blinking 6 times Lamp
communication error)
Lamp failure in lighting Ballast/

E6-3 Status LED blinking 6 times
(communication error) connector
137
5. Troubleshooting
Display
Meaning Details Possible cause
symbol
E9-1 Status LED blinking 9 times Iris error (calibration) Iris
PJ Usage Columns
Display of projector usage time (Projector Hours Used) when an error emerges
TEMP Columns
Display of temperature information when an error emerges

Displayed in the order of [Suction Air], [Lamp], [Exhaust Air], [Ballast] from left to right.
Other Columns
* Display of Service Menu only
Display can differ according to the error phenomenon arising.
• For Fan error
Symbol consisting of 2 alphanumerical characters plus the number of fans (8 for Plato)
Normal “N”
Eco mode Auto “A”
(1 character) Eco1 “E”
Eco2 “L”
Auto “A”
Fan mode
High “H”
(1 character)
Altitude “T”
Normal “O”
Error Fan
Error “X”
* “O” is displayed for the unused fan area.

• For other errors
No particular indications
138
Error Log
Contents of Error Log (Page2) Display
TEMP Columns
Present temperature information is displayed.

Displayed in the order of [Suction Air], [Lamp], [Exhaust Air], [Ballast] from left to right.
Lamp/Filter Clear Count
The number of reset actions is displayed in regard to Lamp Usage / Filter Usage.
Displayed in the order of [No. of reset actions for Lamp Usage] and [No. of reset actions for Filter
Usage].
Cleared with All Data Reset from the Service menu.
Power ON/OFF Count
The number of user’s lamp ON/OFF actions is displayed.

Initialized with Reset – Clear Lamp Hours.
Projector Hours Used
Present Projector Hours Used is displayed.

The same as Projector Hours Used displayed in the Expert menu.
139
5. Troubleshooting
Lamp Voltage: Indicated exceeding the Service Power
The present status of lamp ballast voltage is displayed.
Contents of Error Log (Reset) Display
ALL DATA
All Data Reset is executed according to the User Menu mode.
140 EN
Model Rigel-PJ1
Machine Codes:
Y015/Y016
Appendices
6 January, 2012
TABLE OF CONTENTS
1. Appendix: Specifications
General Specifications.......................................................................................................................................3
List of General Specifications........................................................................................................................3
List of Supported Signals................................................................................................................................6
1
2
General Specifications
List of General Specifications
Optical
PJ X5360N PJ WX5350N
0.63 inch LCD with Micro Lens Array 0.59 inch LCD with Micro Lens Array
LCD Panel
(Aspect Ratio 4:3) (Aspect Ratio 16:10)
Resolution*1 1024 × 768 pixels (XGA) 1280 × 800 pixels (WXGA)
Manual zoom and focus
Lens Zoom Ratio = 1.7

F1.7–2.0 f = 17.4–29.0 mm
Lens Shift (Vertical) 0-0.5V 0-0.6V
265 W AC
Lamp
(195 W in ECO1)
4200 lumens 3500 lumens

Light Output*2*3
ECO1: 75% ECO1: 75%
Contrast Ratio*3
(full white: full 2000:1
black)
Image Size
25–300 inches/0.64 m–7.6 m
(Diagonal)
Projection Distance
26–543 inches/0.65–13.8 m 27–573 inches/0.69–14.6 m
(Min.–Max.)
Projection Angle 0°–16.5° (wide)/0°–9.8° (tele)
*1 Effective pixels are more than 99.99%.

*2 This is the light output value (lumens) when the [PRESET] mode is set to [BRIGHT]. If any other mode
is selected as the [PRESET] mode, the light output value may drop slightly.
3
*3 Compliance with ISO21118-2005
Electrical
2 × RGB/Component (D-Sub 15 P), 1 × HDMI Type A (HDMI® Connector)

Inputs HDCP supported*4, 1 × S-Video (DIN 4 P), 1 × Video (RCA), 1 × (L/R) RCA
Audio, 2 × Stereo Mini Audio
Outputs 1 × RGB (D-Sub 15P), 1 × Stereo Mini Audio
PC Control 1 × PC Control Port (D-Sub 9P)
Wired LAN Port 1 × RJ-45 (10BASE-T/100BASE-TX)
Wireless LAN Port

IEE 802.11 b/g/n (optional Wireless LAN Unit [NP02LM Series] required)
(Optional)
USB Port 1 × Type A, 1 × Type B
Color 10-bit signal processing (1.07 billion colors) (VIEWER, NETWORK: Colors,
Reproduction 16.7 million colors)
Analog: VGA/SVGA/XGA/XGA+/WXGA/WXGA+/SXGA/SXGA+/UXGA
Compatible 480i/480p/576i/576p/720p/1080i/1080p
Signals HDMI: VGA/SVGA/XGA/WXGA/SXGA/480p/576p/720p/1080i/
1080p
Video Bandwidth RGB: 80 MHz (Max.)
Horizontal 540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60

Resolution 300 TV lines: SECAM
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)

Scan Rate
Vertical: 50 Hz to 120 Hz (HDMI: 50 Hz to 85 Hz)
Sync Compatibility Separate Sync
Built-in Speaker 10W (monaural)
Power Requirement 100–240V AC, 50/60Hz
Input Current 3.9 - 1.7 A
4
ECO
MODE
358 W (100-130 V)/343 W (200-240 V)
OFF
(NORMAL)
Pow ECO1
er 271 W (100-130 V)/264 W (200-240 V)
MODE
Cons
umpt STANDBY
ion 9 W (100-130 V/200-240 V)
(NORMAL)
STANDBY
(POWERS 0.2 W (100-130 V)/0.4 W (200-240 V)
AVING)
*4 HDMI® (Deep Color, Lip Sync) with HDCP

What is HDCP/HDCP technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual
Interface (DVI).
If you are unable to view material via the HDMI input, this does not necessarily mean the projector is not
functioning properly.
With the implementation of HDCP, there may be cases in which certain content is protected with HDCP
and might not be displayed due to the decision/intention of the HDCP community (Digital Content
Protection, LLC).
Mechanical
Installation
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Orientation
15.7" (W) × 4.5" (H) × 10.9" (D) /398 mm (W) × 115 mm (H) × 276 mm (D)
Dimensions
(not including protrusions)
Weight 8.6 lbs/3.9 kg
5
Operational Temperatures : 41° to 104°F (5° to 40°C),

(ECO mode selected automatically at 95°F to 104°F/35°C to 40°C)
Environmental
20% to 80% humidity (non-condensing)
Considerations
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
UL/C-UL Approved (UL 60950-1, CSA 60950-1)

Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Regulations
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TÜV Approved)
The specifications are subject to change without notice.
List of Supported Signals
Analog RGB
Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz )
VGA 640 × 480 4:3 60/72/75/85/iMac
SVGA 800 × 600 4:3 56/60/72/75/85/iMac
XGA 1024 × 768 *1 4:3 60/70/75/85/iMac
XGA+ 1152 × 864 4:3 60/70/75/85
WXGA 1280 × 768 *2 15 : 9 60
1280 × 800 *2 16 : 10 60
1360 × 768 *3 16 : 9 60
1366 × 768 *3 16 : 9 60
Quad-VGA 1280 × 960 4:3 60/75
6
SXGA 1280 × 1024 5:4 60/75
SXGA+ 1400 × 1050 4:3 60
WXGA+ 1440 × 900 16 : 10 60
WXGA++ 1600 × 900 *3 16 : 9 60
UXGA 1600 × 1200 4:3 60/65/70/75
WSXGA+ 1680 × 1050 16 : 10 60
HD 1280 × 720 16 : 9 60
Full HD 1920 × 1080 16 : 9 60
MAC 13" 640 × 480 4:3 67
MAC 16" 832 × 624 4:3 75
MAC 19" 1024 × 768 4:3 75
MAC 21" 1152 × 870 4:3 75
MAC 23" 1280 × 1024 5:4 65
HDMI
VGA 640 × 480 4:3 60
SVGA 800 × 600 4:3 60
XGA 1024 × 768 *1 4:3 60
WXGA 1280 × 768 *2 15 : 9 60
1280 × 800 *2 16 : 10 60
1366 × 768 *3 16 : 9 60
Quad-VGA 1280 × 960 4:3 60
SXGA 1280 × 1024 5:4 60
SXGA+ 1400 × 1050 4:3 60
7
WXGA+ 1440 × 900 16 : 10 60
WXGA++ 1600 × 900 16 : 9 60
WSXGA+ 1680 × 1050 16 : 10 60
HDTV(1080p) 1920 × 1080 16 : 9 50/60
HDTV(1080i) 1920 × 1080 16 : 9 50/60
HDTV(720p) 1280 × 720 16 : 9 50/60
SDTV(480p) 720 × 480 4 : 3 / 16 : 9 60
SDTV(576p) 720 × 576 4 : 3 / 16 : 9 50
Component
HDTV(1080p) 1920 × 1080 16 : 9 50/60
HDTV(1080i) 1920 × 1080 16 : 9 50/60
HDTV(720p) 1280 × 720 16 : 9 50/60
SDTV(480p) 720 × 480 4 : 3 / 16 : 9 60
SDTV(576p) 720 × 576 4 : 3 / 16 : 9 50
SDTV(480i) 720 × 480 4 : 3 / 16 : 9 60
SDTV(576i) 720 × 576 4 : 3 / 16 : 9 50
Composite Video/S-Video
Signal Aspect Ratio Refresh Rate ( Hz )
NTSC 4:3 60
PAL 4:3 50
PAL60 4:3 60
SECAM 4:3 50
*1 Native resolution on XGA model (PJ X5360N)
8
*2 Native resolution on WXGA model (PJ WX5350N)

*3 The projector may fail to display these signals correctly when [NORMAL]
is selected for [ASPECT] in the on-screen menu.
The factory default is [NORMAL] for [ASPECT]. To display these signals, select [16:9] for [ASPECT].
• Sync on Green and Composite sync signals are not supported.

• Signals other than those specified in the table above may not be displayed correctly. If this should
happen, change the refresh rate or resolution on your PC. Refer to Display Properties help section
of your PC for procedures.
9
MEMO
10
MEMO
11
MEMO
12 EN

Rigel-Pj1 NX FSM en Final 170212

Uploaded by

Copyright:

Available Formats

Rigel-Pj1 NX FSM en Final 170212

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rigel-Pj1 NX FSM en Final 170212

Uploaded by

Copyright:

Available Formats

Model Rigel-PJ1 nx/nw

Field Service Manual

• RISK OF ELECTRIC SHOCK DO NOT OPEN

• HEATSINK MAY BE ENERGIZED. TEST BEFORE TOUCHING.

During servicing carefully observe the following.

5 Adjustable Tilt Foot Lever

6 Adjustable Tilt Foot

10 Lens Shift Dial (Vertical)

11 Ventilation (inlet) / Filter Cover

1 Port Cover for USB Wireless LAN Unit

6 Built-in Security Slot

7 Security chain opening

• While an on-screen menu is displayed, you can use the

Proceeds to the next hierarchical menu in the currently

Displays an on-screen menu for setting or adjusting a variety

Detects the signal input.

Turn the projector on and then off (standby).

6 Status Indicator p.119

Returns to the previous hierarchical menu in the currently

Automatically adjust the projector to an optimal state for

10 Power Indicator p.119

11 Lamp Indicator p.119

Terminal Panel Features

1 USB Port (Type A)

2 LAN Port (RJ-45)

3 USB (PC) Port (Type B)

4 HDMI In Connector (Type A)

5 Computer 2 Audio In Mini Jack (Stereo Mini)

6 Computer 2 In / Component Input Connector (Mini D-Sub 15 Pin)

7 S-Video In Connector (Mini DIN 4 Pin)

8 Computer 1 Audio In Mini Jack (Stereo Mini)

9 Computer 1 In / Component Input Connector (Mini D-Sub 15 Pin)

10 Audio Out Mini Jack (Stereo Mini)

11 PC Control Port (D-Sub 9 Pin)

12 Monitor Out (Comp.1) Connector (Mini D-Sub 15 Pin)

13 Video/S-Video Audio In (L/Mono, R) Connectors (RCA)

14 Video In Connector (RCA)

Part Names of the Remote Control

Pressing the Power button once displays the power-off confirmation

Confirm that the projector is in standby (the Power indicator is lit

Select the COMPUTER1/2 input or a component.

5 S-Video Button Select the S-VIDEO input.

6 Video Button Select the VIDEO input.

7 Network Button Select the Network.

8 Viewer Button Select the Viewer.

Displays an on-screen menu for setting or adjusting a variety of

Proceeds to the next hierarchical menu in the currently displayed

13 Magnify (+)(−) Button Used to zoom in and out on the screen.

Used when the machine is connected to a computer via a USB

16 Help Button Displays the information screen.

17 Keystone Button Displays the screen for adjusting the trapezoid.

Automatically adjust the projector to an optimal state for projection

19 HDMI Button Select the HDMI input.

20 USB Display Button Select the USB Display.

Displays the current video image as a still image. Pressing the

Returns to the previous hierarchical menu in the currently displayed

Used to adjust display position when the screen is enlarged by

Used to switch the viewer between thumbnail views. This button is

Used when the machine is connected to a computer via a USB