BassLink T

Powered Subwoofer System

SERVICE MANUAL

Infinity Systems, Inc.

250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 7/2004
BassLink T
- CONTENTS -

SPECIFICATIONS ………………………………….……..1
CONNECTIONS/APPLICATIONS……………………..…2
CONTROLS AND FUNCTIONS.……...……..…...…...…5
BASIC TROUBLESHOOTING..…….…….………………6
EXPLODED VIEW/PARTS LIST…………………………7
DISASSEMBLY PROCEDURE………………………..…8
AMPLIFIER BLOCK DIAGRAM……………………….…9
ELECTRICAL PARTS LIST ……………………………. 10
P.C.B. DRAWINGS….…………………………………….14
IC/TRANSISTOR PINOUTS…………………………….. 19
SCHEMATICS……………………………………………..23
PACKING…………………………………………………..26

Basslink T Specifications

Output Power (14.4V supply) 250W RMS

Type of Amplifer AB
Frequency response: 20Hz – 120Hz
Maximum input signal: 4.0V
Maximum sensitivity: 50mV to 4V Line-level input
1V to 16V High-level input
Input Impedance 20K Ω
Idle Current <800mA
Signal to Noise >100dB (A-weighted ref to full power)
Crossover Type Fixed LP @ 12dB per octave
Crossover Range Variable 70 – 170 Hz
Min Current Draw (Idle) 1.13A
Remote Current Draw <30mA
Max Current Draw 26A
DC Offset <30mV
Bass Boost -6dB to +3dB @ 40Hz
Auto Turn-On 2 -10min (Time to turn Off)
Operating Voltage 10 – 16 VDC
Dimensions: 40 3/8 x 6 7/16 x 14 3/8” (L x W x D)
(1026mm x 164mm x 366mm)
Fuse: 30A

Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and details in
this and related JBL publications are therefore subject to change without notice.

1
BassLink T

POWER CONNECTIONS
Connect power to BassLink T, as shown in Figure 6. Power connections for BassLink T.
Figure 6. Also observe these installation tips:
BassLink T
(Control Panel)
• Use at least #10 AWG wire for the +BATT
(+12 Vdc) and GND (ground) connections. If POWER
LINE LEVEL
INPUT
HIGH LEVEL
INPUT
needed, use at least a #20 AWG wire for the + +
L R
REM (remote) connection. – –
REMOTE L R
+BATT REM GND LEVEL
FUSE CONTROL
• Route all power wires through a grommet in 25A

the vehicle’s firewall. If a factory grommet is

unavailable, install one.

• Connect a short GND wire from BassLink T

to the nearest bare metal surface. For a
good connection, scrape away paint from
the metal surface and use a screw with a
lock (star) washer.

• Install a fuse holder with a 25 A fuse within

18" of the battery’s positive (+) terminal (see
Figure 6).

• The REM connection requires +5 to +12 Vdc Fuse 25 A

signal to turn on BassLink T. Most head units
with preamp outputs provide this remote
voltage signal. For speaker-level applications,
a remote connection is preferred but not
required, since BassLink T’s Auto Turn-On
feature will sense voltage on the speaker
wires to automatically turn on BassLink T.

IMPORTANT: To enable BassLink T’s Auto

Turn-On feature, set the AUTO TURN-ON
switch to the AUTO position (see Figure 12
on page 7).

2
BassLink T
APPLICATIONS
BassLink T is equipped with two line-level (RCA)
inputs and two speaker-level inputs.

To help you plan your installation, we have

included two system applications in Figures 7
and 8 on pages 4 and 5. For more system ideas,
see your authorized Infinity car audio dealer.

Figure 7. BassLink T audio connections for a head

unit with two line-level or subwoofer (RCA) outputs.

LINE LEVEL HIGH LEVEL AUTO

POWER INPUT INPUT TURN ON BASS
GAIN CROSSOVER BOOST
+ +
L R OFF AUTO

– – PHASE
REMOTE L R
+BATT REM GND LEVEL
FUSE CONTROL
25A 0° 180°

3
BassLink T
APPLICATIONS (CONTINUED)
Figure 8. BassLink T audio connections for a head
unit equipped with two speaker-level outputs.

LINE LEVEL HIGH LEVEL AUTO

POWER INPUT INPUT TURN ON BASS
GAIN CROSSOVER BOOST
+ +
L R OFF AUTO

– – PHASE
REMOTE L R
+BATT REM GND LEVEL
FUSE CONTROL
25A 0° 180°

4
 BassLink T

CONTROLS AND FUNCTIONS TUNING BASSLINK T

BassLink T provides several controls and indica- NOTE: Depending on BassLink T’s orientation and 1. Unplug the RJ11 cable that connects the 8. Adjust the CROSSOVER control clockwise
tors that simplify sonic integration with virtually location in a vehicle, reversing the phase may Remote Level Control to BassLink T. or counterclockwise until you hear only low-
any vehicle’s unique acoustic properties. They are (or may not) increase or decrease the amount frequency information. For example, you
located on the top control panel, as shown in of perceived upper bass being reproduced. 2. Make sure the head unit is off and its volume should NOT hear any vocals coming from
Figure 12. control is set to minimum. BassLink T when seated in the normal
AUTO TURN-ON: For speaker-level connections, listening position.
GAIN Control: Use this control to adjust the use this switch to activate (or deactivate) 3. On BassLink T’s top panel, initially set all
relative volume (loudness) of BassLink T with BassLink T’s automatic turn-on circuit. controls to their midpoint positions, as shown 9. Adjust the BASS-BOOST control clockwise
respect to the other speakers in the vehicle. in Figure 12. On BassLink T’s top panel, or counterclockwise to suit your taste.
REMOTE LEVEL CONTROL: Use this RJ11 jack initially set PHASE to 0°.
CROSSOVER: Use this control to adjust the to connect the Remote Level Control (see page 6). 10. Recheck the PEAK LED to make sure it’s
amount of high-frequency information present in 4. Turn on the head unit and play a favorite flashing in time with the bass but is not lit
BassLink T’s output. A lower value means more of PEAK LED: This indicator glows red when the music track that has substantial bass. Set the continuously. If it is lit continuously, adjust
the high frequencies are filtered out. subwoofer is at maximum output. Be sure to head unit’s volume control to 75 percent of the GAIN control counterclockwise until the
monitor this indicator during BassLink T setup the total output (approximately 3 o’clock on PEAK LED only flashes.
BASS BOOST: Use this control to correct any (see Tuning BassLink T). When properly tuned, rotary controls).
perceived peak or dip in the bass response the PEAK LED should light momentarily during 11. Reconnect the RJ11 cable between the Remote
(typically around 40Hz in most vehicles). Set the high-level bass transients. Avoid adjustments 5. Adjust the GAIN control clockwise until the Level Control and BassLink T. You may then
control to any value between –6dB and +3dB, that cause the PEAK LED to remain lit for PEAK LED (on BassLink T’s top panel) begins use the Remote Level Control to adjust the
according to your preference. extended periods. to flash with each bass note but doesn’t stay level of the bass to suit your taste and/or
lit continuously. different program material.
PHASE Control: Use this switch to reverse the POWER LED:This indicator will glow blue when
phase of BassLink T’s output with respect to its BassLink T is operational. 6. Listen to your system, making a mental NOTE: In most cases, the above steps will provide
input. Choose the position (0° or 180°) that note of the amount of upper bass being satisfactory tuning. However, the actual process
sounds the best. reproduced. may require several readjustments of each control,
since the settings will interact with each other.
7. Switch the PHASE control to 180° and listen If necessary, consult your authorized Infinity
Figure 12. BassLink T control panel. again for upper bass content. There may be car audio dealer for help in tuning your system.
more upper bass, less upper bass, or no
AUTO
POWER
LINE LEVEL
INPUT
HIGH LEVEL
INPUT TURN ON BASS change at all. The position that provides the
GAIN CROSSOVER BOOST
+ + PEAK most upper bass is correct, but choose either
L R OFF AUTO
setting according to your taste.
– – PHASE
REMOTE L R
+BATT REM GND LEVEL
FUSE CONTROL
25A 0° 180°

5
 BassLink T
TROUBLESHOOTING
• PROBLEM: • PROBLEM: • PROBLEM:
POWER LED is not lit. No output from BassLink T when head-unit BassLink T produces a loud humming noise with
fader control is set to front or rear. the system OFF when using speaker-level inputs.
CAUSES and SOLUTIONS:
1. Fuse is blown and needs replacement. CAUSE and SOLUTION: CAUSE and SOLUTIONS:
2. Head unit is not functioning properly. Check Input connections are improperly wired. Verify This problem is caused by a feedback loop
remote voltage, and power, ground or remote all connections (see Applications, starting on between your speakers and the high-level inputs
connections. page 4). of BassLink T.

Choose one of the following solutions:

• PROBLEM: • PROBLEM:
POWER LED is lit but there is no bass. BassLink T turns on before head unit is 1. Connect a wire from the REMOTE terminal on
completely on and produces a “thump” sound. BassLink T to the remote turn-on of your head
CAUSES and SOLUTIONS: unit or to the vehicle’s accessory circuit. On the
1. Inputs are not connected. Check connections. CAUSE and SOLUTION: control panel, slide the AUTO-ON switch to the
2. Head-unit fader control is not set properly. For speaker-level connections, BassLink T is OFF position.
Adjust head-unit fader control to feed audio receiving a false turn-on signal. On BassLink T’s
signals to BassLink T. top panel, slide AUTO TURN-ON to OFF and use 2. Connect the supplied capacitors between each
the Remote (REM) connection. of the speaker outputs of the head unit and
the speaker’s positive lead. Connect each
• PROBLEM: positive lead of BassLink T’s high-level inputs
BassLink T sounds muddy or distorted. • PROBLEM: to the head-unit side of the capacitors. Use
BassLink T’s POWER LED remains on after head one capacitor per speaker input channel.
CAUSES and SOLUTIONS: unit is turned off.
1. Gain is set too high and PEAK LED is lit Figure 10. Connecting supplied capacitors.
constantly. Readjust GAIN control (see CAUSE and SOLUTION:
+ Speaker wire
Tuning BassLink T on page 7). For speaker-level connections, this is normal from head unit To + speaker lead
2. Bass is set too high. Readjust BASS BOOST operation when AUTO TURN-ON is set to ON. Capacitor
control (see Tuning BassLink T on page 7). BassLink T will remain on another 5 to 10 minutes
3. Head-unit output is distorted or blown. See after sensing that audio signals are not present
your authorized Infinity car audio dealer. before shutting down. To + speaker-level
input on BassLink T

6
 Basslink T

BASSLINK T EXPLODED VIEW

Ref # Part Number Description Qty

1 329-000-05012-0BA Front grille 2

2 329-100-05013-0BA Grille ass’y 1
3 321-FE-05006-0BA Bracket stand 2
4 243-100-05017-0BA Front cabinet 1
5 333-EVA-05024-0BA EVA gasket 1
6 323-AL-05016-0BA Heatsink extrusion 1
7 309-ABS-05005-0BA Control Cover Ass’y 1
8 352-DM3219C376 Screw 12
9 352-FE-05014-0LA U-bracket 1
10 352-AM04014C326 Screw 2
11 PR-255007 10” passive driver 2
12 F25X12PR-01DW 10” woofer 1
13 355-L06025 Spring washer m4 24
14 352-AM04014C326 Screw 4*14 24
15 336-EVA-05045-0BA EVA gasket 2
16 352-AM03010D065 Screw 6
17 011-7525-00488 Trunk sub amp 1
18 333-EVA-05026-0BA EVA gasket 1
19 051-B00488B Jack tone pcb ass’y 1
20 352-GM03010F055 Screw 8
21 309-ABS-05002-0BA Sealing cover ass’y 1
22 333-EVA-05023-0BA EVA gasket 1
23 247-100-05011-0BA Rear cover 1
24 352-HM04016B190 Screw 34
25 351-HM04010A217 Machine screw 2
26 315-PC-05019-0TA PC trim plate 1
27 315-PC-05020-0TA PC trim plate 1
28 327-010-05000-0BA Door latch 1
29 316-ABS-05006-0BA Infinity logo 1
30 352-AM03010D065 Screw 3
31 351-AM03008A079 Machine screw 3
32 352-AM02010D006 Screw 2
33 333-EVA-05021-0BA EVA gasket 1

7
BassLink T
DISASSEMBLY PROCEDURE FOR BASSLINK T (ACCESS TO AMPLIFER, DRIVERS)

1) On a protected work surface, stand the unit up so the back panel is facing you.
2) Remove the (12) Phillips screws holding the black heatsink to the enclosure. Do not remove the
heatsink at this time.
3) Remove the (36) Phillips screws holding the back panel to the main enclosure. Note in the area of the
heatsink, two screws are shorter, machine screws.
4) Carefully separate the back panel from the main enclosure; try not to damage the O-ring that may be
adhered to both sides of the enclosure, preventing its separation. Note the LED wires from the
heatsink area routed to the amplifier; unplug the 2 lead connection at female connector M2 on the
amplifier. Set the heatsink and LED w/ wires aside.
5) Unplug the woofer wires from the terminals.
6) Completely separate the two enclosure halves.

SERVICING THE INPUT/PREAMP SECTION

7) Remove the (8) Phillips screws holding the cover plate to the enclosure.
8) With a wood chisel or similar tool, carefully pry the plastic cover away from the cup, working around the
perimeter, until the cover is detached. If the cover is damaged during this procedure, order
part# 309-ABS-05002.

REASSEMBLY

9) If the cover to input/preamp section was detached, apply a bead of silicon sealer or similar adhesive
around the perimeter of the cover, in the sealing groove. Without this adhesive, there may be an air
leak which would affect performance. Press the cover into place.
10) Attach the woofer wires.
11) Before the enclosure can come together, connecting the heatsink/LED wire presents a challenge if not
correctly done. The LED wire must thread through the enclosure, the small hole in the aluminum
heatsink plate, and back into the M2 connector on the amplifier. The position in which this is best
achieved is with Basslink T laying flat side down on a surface, woofer side up. Partially bring the
enclosure halves together, and work through the remaining gap near the heatsink end. See illustration.
12) Make sure the O-ring around the perimeter of the enclosure is intact and in place. Make sure the two
shorter machine screws are used in the back panel, in the area near the heatsink.
13) Replace all enclosure and heatsink screws.

8
BassLink T

9
 BassLink T
BASSLINK T Electrical Parts List
Part Numbers Description Reference Designators

POWER SUPPLY/AMPLIFIER PCB

Resistors

110-12102j52 resistor 1K 1/2W ±5% 52mm RX1

110-14000j26 resistor 0Ω 1/4W ±5% 26mm R525,530
110-16000j26 resistor 0Ω 1/6W ±5% 26mm D603
110-16100j26 resistor 10Ω 1/6W ±5% 26mm R521,523,613,500
110-16102j26 resistor 1K 1/6W ±5% 26mm R519,541,542,502,560,629,605
R285,294,508511,540,611,507,612,616,621,622,623,
110-16103j26 resistor 10K 1/6W ±5% 26mm
625,626,627,600,601,604,606
110-16104j26 resistor 100K 1/6W ±5% 26mm R517,618,624,603
110-16105j26 resistor 1M 1/6W ±5% 26mm R422,420
110-16106j26 resistor 10M 1/6W ±5% 26mm R421
110-16122j26 resistor 1.2K 1/6W ±5% 26mm R295
110-16123j26 resistor 12K 1/6W ±5% 26mm R234,513
110-16152j26 resistor 1.5K 1/6W ±5% 26mm R550
110-16154j26 resistor 150K 1/6W ±5% 26mm R80A
110-16182j26 resistor 1.8K 1/6W ±5% 26mm R74A
110-16183j26 resistor 18K 1/6W ±5% 26mm R274
110-16204j26 resistor 200K 1/6W ±5% 26mm R237
110-16220j26 resistor 22Ω 1/6W ±5% 26mm R526,527,528,529
110-16221j26 resistor 220Ω 1/6W ±5% 26mm R76A,424,501
110-16222j26 resistor 2.2K 1/6W ±5% 26mm R228,515
110-16223j26 resistor 22K 1/6W ±5% 26mm R254,287,628,602
110-16333j26 resistor 33K 1/6W ±5% 26mm R277,614
110-16393j26 resistor 39K 1/6W ±5% 26mm R631
110-16432j26 resistor 4.3K 1/6W ±5% 26mm R505
110-16433j26 resistor 43K 1/6W ±5% 26mm R503
110-16471j26 resistor 470Ω 1/6W ±5% 26mm R510,522,524
110-16472j26 resistor 4.7K 1/6W ±5% 26mm R275,276,520
110-16473j26 resistor 47K 1/6W ±5% 26mm R77A,257,273,290,14A
110-16474j26 resistor 470K 1/6W ±5% 26mm R278
110-16511j26 resistor 510Ω 1/6W ±5% 26mm R256,286
110-16512j26 resistor 5.1K 1/6W ±5% 26mm R514
110-16562j26 resistor 5.6K 1/6W ±5% 26mm R238,518,630
110-16681j26 resistor 680Ω 1/6W ±5% 26mm R504,509
110-16682j26 resistor 6.8K 1/6W ±5% 26mm R516,77C
110-16755j26 resistor 7.5M 1/6W ±5% 26mm R293
116-141r00j26x metal film resistor 1.00Ω 1/4W ± 5% MO 26mm R615
116-142201j26x metal film resistor 2.2K 1/4W ± 5% MO 26mm R532,534
116-161132f26 metal film resistor 11.3K 1/6W ± 1% MO 26mm R512
116-167871f26 metal film resistor 7.87K 1/6W ± 1% MF 26mm R279
113-50r22j2z cement resistor 0.22Ω 5W ±5% R81A,82A
116-301000j52x metal film resistor 100Ω 3W ± 5% 52mm R539
116-303300jk2x metal film resistor 330Ω 3W 5% 10mm R531,533

Capacitors

130-2b101k503 disc capacitor 100P 50V ± 10% C214,253,CM1,CM2,CM3,CM4

130-2b221mj03 disc capacitor 220P 1000V ± 20% C539
C268,269,502,503,506,509,510,511,512,533,535,540,
130-2f104z503 disc capacitor 0.1U 50V +80/-20%
611,621,623,624,625
130-3f222k503 disc capacitor 0.022uF 50V ± 10% CX5
132-102ja03 mylar capacitor 0.001uF 100V ±5% C62A,62B 420
132-103j503 mylar capacitor 0.001uF 100V ±5% C252,270,271
132-103ja03 mylar capacitor 0.01uF 100V ±5% C67
132-104ja03 mylar capacitor 0.1uF 100V ±5% C10A,10B,522,524,526,528,537,538,600
132-273ja03 mylar capacitor 0.027uF 100V ±5% C60A,66A66B
132-472j503 mylar capacitor 0.047uF 50V ±5% C507
135-3106m50 electrolytic 10uF 50V ±20% C272,273
135-3226m50 electrolytic 22U 50V ±20% C264,508
135-3227m25 electrolytic 220U 25V ±20% C504
135-3335m50 electrolytic 3.3uF 50V ±20% C601
135-3337m16 electrolytic 330uF 50V ±20% C612,622
135-3476m50 electrolytic 47uF 50V ±20% C421,422,251,531,532,534,536

10
BassLink T
Part Numbers Description Reference Designators

POWER SUPPLY/AMPLIFIER PCB

135-b227m35 electrolytic 220uF 35V ±20% 105 C502A

136-3336m50 non-polar capacitor NP 85 33uF 50V CX4
129-a105j633 metalize 1uF 63V ± 5% MSC C505
132-334j504 mylar capacitor 0.33U 50V ± 5% C500,501A
138-5108m801 electrolutic 1000uF 80 ± 20% ψ20*25 C521,523
138-5228m801 electrolutic 2200uF 80 ± 20% ψ25*30 C525,527
138-6338m351 electrolutic 3300uF 35 ± 20% ψ25*25 C501

Semiconductors

Q201,404,405,406,501,503,513,514,601,610,611,612
192-027c1815gr transistor 2SC1815GR NPN
,622,624, 626
192-027c2235y transistor 2SC2235Y NPN Q16A
192-028a1015gr transistor 2SA1015GR PNP Q502,504,505,506,621,623,625,202,602
192-028a965y transistor 2SA965Y PNP Q500
197-031n4148 diode 100mA 75V SIGNAL 1N4148 ROHM D201,202,503,550,552,611,612,613,601,52A
199-05001505j zener diode 500mW 15V ROHM 52mm 1N5245B Z501,502
199-15000625 zener diode 6.2V 12W 52mm Z500
190-13494cn IC TL494CN PWM U500
190-16tl074cn IC TL074CN ST QUAD OP-AMP U203
190-99pc817c IC PC817C OPTOCOUPLER U501
192-027c1815gr transistor 2SC1815GR NPN Q200
192-161tip31c transistor TIP31C SGS NPN Q531
192-162tip32c transistor TIP32C SGS PNP Q532
192-16360nf06 transistor STP60NF06 SGS FET Q508,509,510,511
195-10204ubd LED 204-10UBD LD500
197-141n4004 diode 1N4004 D50
197-301604gd diode SF1604G-D D511,512
197-30sf16 diode SF16 D600

Miscellaneous

109-1ttc802j0 thermister TTC-802(js) NTC TH1

120-1000003 inductor 10W AI YT-C3104-005 1CRHW 354708LTB B500,501,502
122-11350j200 inductor R10*38 35uF ψ 2.0 L501
122-14106m130 inductor MIZI R251510 3*ψ 1.3 1.0mH L500
123-11k5arh06 inductor BEAD CORE-TECh K5A RH 3.5*1.6*6 Q508,509,510,511
150-r36231504 power transformer RT36-6T:28T T500
162-5002d001 wire 20mm 2PIN
162-5002d002 wire 20mm 3PIN
162-50122004 wire 120mm RED/WHT 2PIN
171-u845h2ac relay 845H-2A-C 12VDC RL50
175-1c02v01 wire connector 2PIN PITCH=2.5mm M2
175-1c08v01 wire connector 8PIN PITCH=2.5mm M1
176-ft205 wire connector FASTON M#205 S+,-
176-trpcb1m4 wire connector PCB1M4 BAT+,-
162-5045d002 WIRE RED UL1015 450mm RED/BLK #205T0.8 #250/110 T0.5
193-0s4211 insulator 42*11 CLASS-D-1
193-201612tr insulator T0-220 16mm*12mm
193-201815t2 insulator
193-2m1813 insulator T0-220 18*13mm Q508,509,510,511,531,532,D511,D512
236-AL-05001 AL holder
323-AL-05013-0LA HEAT SINK 250*240*61*3T SILVER
333-SPG-05036-0BA SPONGE 500*50*5T
351-AM03005A015 SCREW M3*0.5P*5L BLK TO PCB/CU HOLDER-6
351-AM03006A069 SCREW M3*6 BLK
351-AM03007A368 SCREW M3*7 BLK TO H-S/CU HOLDER-6
351-AM03008A079 SCREW M3*8 BLK CONTROL PCB TO NYL SPACE-4
351-AM03012A090 SCREW M3*12 BLK IC-HOLDER-1
351-AM03018A364 SCREW M3*18 BLK CLASS-D-2
351-BM03014A093 SCREW M3*14 BLK HEAT SINK TO IC HOLDER-4
351-FM04006A220 SCREW M4*6 NI
355-P0407236 SPRING WASHER M4 ID4.2* OD7.0*T1.0
361-FE-05000 IC HOLDER 69*12*4*1.5T
361-FE-05003-0LA IC HOLDER 25*12*4*1.5T TO IC-1
362-CU-05004-0YA CU SPACER M3*8H
362-CU-05010 CU SPACER M3*11.8H

11
BassLink T
Part Numbers Description Reference Designators

INPUT/PREAMP PCB

362-NYL-05006-0WA HOLDER(NYLON)10H(MAE-10T;HAKUTO-10)WHT

Resistors

110-16102j26 resistor 1K 1/6W ±5% CF 26mm R219,222,233

110-16103j26 resistor 10K 1/6W ±5% CF 26mm R229,23,24,302,307,309,312,330,5,6
110-16104j26 resistor 100K 1/6W ±5% CF 26mm R301,36
110-16123j26 resistor 12K 1/6W ±5% CF 26mm R227
110-16151j26 resistor 150Ω 1/6W ±5% CF 26mm R311,310
110-16153j26 resistor 15K 1/6W ±5% CF 26mm R252,218,328,304
110-16154j26 resistor 150K 1/6W ±5% CF 26mm R329
110-16204j26 resistor 200K 1/6W ±5% CF 26mm R27,28,29,30
110-16222j26 resistor 2.2K 1/6W ±5% CF 26mm R37,38,39,40
110-16223j26 resistor 22K 1/6W ±5% CF 26mm R240,241,250
110-16243j26 resistor 24K 1/6W ±5% CF 26mm R225
110-16302j26 resistor 3K 1/6W ±5% CF 26mm R200
110-16303j26 resistor 30K 1/6W ±5% CF 26mm R305
110-16333j26 resistor 33K 1/6W ±5% CF 26mm R253
110-16392j26 resistor 3.9K 1/6W ±5% CF 26mm R224
110-16393j26 resistor 39K 1/6W ±5% CF 26mm R223
110-16472j26 resistor 4.7K 1/6W ±5% CF 26mm R1,2,19,20
110-16474j26 resistor 470K 1/6W ±5% CF 26mm R220
110-16511j26 resistor 510Ω1/6W ±5% CF 26mm R303,306
110-16513j26 resistor 51K 1/6W ±5% CF 26mm R10,11,12,9,17,18
110-16683j26 resistor 68K 1/6W ±5% CF 26mm R251
110-16752j26 resistor 7.5K 1/6W ±5% CF 26mm R221
129-a104j633 metalize 0.1U 63V ± 5% MSC C211
129-a224j633 metalize 0.22uF 63V ± 5% MSC C215,260,261,262,263,210
129-a823j633 metalize 0.082U 63V ± 5% MSC C216
115-v503b103 variable resistor RV09AC-40-30K-B50K VR201,202
115-v503b204 variable resistor RV09A02-40-30K-B50K VR203

Capacitors

130-2b101k503 disc capacitor 100P 50V ± 10% C242,CW1,CW2,CW3,CW4,CW5,C11,12

130-2b102k503 disc capacitor 1000P 50V ± 10% CX1
130-2b221k503 disc capacitor 220P 50V ± 10% C3,4
130-2f104z503 disc capacitor 0.1U 50V +80/-20% C229,231,233,234,235,274,301,303,5,6,CX2
132-103j503 mylar capacitor 0.01U 50V ± 5% C217,13
135-3105m50 electolytic 1U 50V ± 20% C311
135-3106m50 electolytic 10uF 50V ± 20% C228,230,300,302
135-3475m50 electolytic 4.7U 50V ± 20% C312
137-3106m50 electolytic 10uF 50V ± 20% C7,8,9,266,267
137-3226m50 electolytic 22uF 50V ± 20% C2
135-0108m25 electolytic 1000U 25V ± 20% CX3
137-3226m50 electolytic 22uF 50V ± 20% 85 C1

Semiconductors

192-027c1815gr transistor 2SC1815GR NPN Q301

197-031n4148 diode 100mA 75V SIGNAL 1N4148 ROHM D1,2
190-06m13700n IC NJM13700N JRC DUAL OP-AMP U301
190-06m45581 IC NJRC NJM4558LD DUAL OP-AMP U1,200,204,205
195-10204hd LED 3mm FOR STANDBY LED1
197-306a20 diode 6A 200V 6A20 DXXX
Miscellaneous

154-1025a800 fuse 25A 32V ATC UL/CSA F500

155-9f30240 fuse holder F30240100P
162-50048002 wire 45mm 9PIN PITCH=2.5mm W2
162-80098001 wire 90mm 26AWG
162-80659001 wire 650mm W1
162-a0802001 wire UL1015 12AWG 800mm RED/BLK
174-020123bg RCA PIN JACK JK020123BG JK1
174-535913sg DC JACK SL035913SG JK500
174-9mjd0604 M/JACK D/S 6P4C 6U" JK4
175-9h04v01 wire connector 4PIN PITCH=4.2mm JK2

12
 BassLink T
Part Numbers Description Reference Designators

CLASS-D 300 ASS'Y

180-s570050 switch SS70050-0202-10T-NN SW1,2

359-FIB-00001 fiber washer ψ12*1.5 adhesive
362-NYL-05005-0WA LED spacer(nylon) ψ4*10.5H LED1

Resistors

118-12061001j SMD resistor 1.00K 1206 5% R2

118-12061002j SMD resistor 10.0K 1206 5% R25,29,30,30B,7,9
118-120610r0j SMD resistor 10.0Ω1206 5% R20,20B,22,23
118-12062002j SMD resistor 20.0K 1206 5% R26
R6,13,16,31,33,34,35,36,37,38,39,40,41,42,43,44,45,
SMD resistor 2.20K 1206 5%
118-12062201j 46,32
118-12062204j SMD resistor 2.20M 1206 5% R4
118-12062701j SMD resistor 2.70K 1206 5% R10
118-12063000j SMD resistor 300.0Ω1206 5% R24
118-12063301j SMD resistor 3.3K 1206 5% R1,14,15,27,28
118-12063902j SMD resistor 39.0K 1206 5% R3
118-12064700j SMD resistor 470Ω1206 5% R8,11,21
118-12064701j SMD resistor 4.7K 1206 5% R5,12
141-c0101k50 SMD capacitor 100pF 50V 10%1206 NP0 C4
141-c0220k50 SMD capacitor 22pF 50V 10%1206 SMT NP0 C5
141-c0561k50 SMD capacitor 560pF 50V 10%1206 NPO C6
141-c5104m50 SMD capacitor 1206 Y5V 0.1uF 50V ± 20% C2,3,7,8,9,10,11,15
141-c7223k50 SMD capacitor 0.022uF 50V 10% 1206 X7R C13
141-d7104ka0 SMD capacitor 0.1uF 100V 10% 1210 X7R C12,14,18,19

Capacitors

132-104kb04a mylar capacitor 0.1uF 200V ± 10% PITCH 10mm C20

132-105kb50 mylar capacitor 1uF 250V ± 10% C40

Semiconductors

190-16tl072dts IC TL072CDT SGS THOMSON DUAL OP-AMP IC1

192-09124126qs SMD transistor 2SC2412K-T1460/R ROHM Q1,4
192-09139066rs SMD transistor 2SC3906K-T146R ROHM Q2,8
192-091sc4672 SMD transistor 2SC4672 ROHM Q5B
192-09210376qs SMD transistor 2SA1037K-T146Q/R ROHM Q7,9
192-09215146rs SMD transistor 2SA1514K-T146R ROHM Q3
192-1682n5401 Transistor 2N5401 AI-PNP 350V 500mA T0-92 Q6B
197-03rls4148s SMD diode RLS4148-TE11 ROHM D1,2,3,4,5,5B,6,20
199-15000563s SMD ZENER 5.6V 5% PHILIPS BAX84-CV6 Z1,2
199-15001203s SMD ZENER 12V 5% PHILIPS BAX84-C12 Z3,4,5,6
192-232irf9640 transistor IRF9640 IR P-CH TO220 MOSFET Q10,10B
192-233irf640 transistor IRF640 IR N-CH TO-220 MOSFET Q11
122-13151k0190 inductor CHOKE SA-500-280 L1
122-14300k4 inductor ferrite core LD1215*300KU ± 10% L2

Capacitors

128-e106ma01-s non-polar electrolytic 10uF 100V 20% C16,17

132-104kb04a mylar capacitor 0.1uF 200V ± 10% PITCH 10mm C20
132-105kb50 mylar capacitor 1uF 250V ± 10% C40

13
BassLink T

14
BassLink T

15
BassLink T

16
BassLink T

17
BassLink T

18
BassLink T
BASSLINK T IC PINOUTS

NJM137000N PINOUTS

1.Amp Bias Input A 9.Buffer Output B

2.Diode Bias A 10.Buffer Input B
3.+ Input 11.V+
4.- Input 12.Output B
5.Output A 13.-Input B
6.V- 14.+Input B
7.Buffer Input A 15.Diode Bias B
8.Buffer Output A 16.Amp Bias Input B

NJM4558L PINOUTS

1.A Output 5.B +Input

2.A -Input 6.B -Input
3.A +Input 7.B Output
4.V- 8.V+

TL494 PINOUTS

1.Err Amp 1 In+ 9. E1

2.Err Amp 1 In- 10. E2
3.Feedback 11. C2
4.Dead-Time Ctrl 12. Vcc
5.Ct 13. Output Ctrl
6.Rt 14. Ref
7.Gnd 15. Err Amp 2 In-
8.C1 16. Err Amp 2 In+

19
BassLink T

TL074
TL074A - TL074B
LOW NOISE J-FET QUAD OPERATIONAL AMPLIFIERS

. WIDE COMMON-MODE (UP TO VCC+) AND

.. DIFFERENTIAL VOLTAGE RANGE

LOW INPUT BIAS AND OFFSET CURRENT

.. LOW NOISE en = 15nV/√Hz (typ)

OUTPUT SHORT-CIRCUIT PROTECTION
HIGH INPUT IMPEDANCE J–FET INPUT

.. STAGE
LOW HARMONIC DISTORTION : 0.01% (typ)
N
DIP14

.. INTERNAL FREQUENCY COMPENSATION

LATCH UP FREE OPERATION
HIGH SLEW RATE : 13V/µs (typ)
(Plastic Package)

D
SO14
(Plastic Micropackage)

DESCRIPTION ORDER CODES

The TL074, TL074A and TL074B are high speed Temperature Package
J–FET input quad operationalamplifiers incorporating Part Number
Range N D
well matched, high voltage J–FET and bipolar transis- o o
TL074M/AM/BM –55 C, +125 C • •
tors in a monolithic integrated circuit. o o
TL074I/AI/BI –40 C, +105 C • •
The devicesfeaturehigh slew rates, low input bias and o o
offset currents, and low offset voltage temperature TL074C/AC/BC 0 C, +70 C • •
coefficient. Example : TL074IN

PIN CONNECTIONS (top view)

Output 1 1 14 Output 4

Inverting Input 1 2 - - 13 Inverting Input 4

Non-inverting Input 1 3 + + 12 Non-inverting Input 4

VCC + 4 11 VCC -

Non-inverting Input 2 5 + + 10 Non-inverting Input 3

Inverting Input 2 6 - - 9 Inverting Input 3

Output 2 7 8 Output 3

October 1997 1/10

20
BassLink T

BASSLINK T TRANSISTOR PINOUTS

PINOUTS
PARTS NAME
1 2 3
IRF9640 Gate Drain Source
IRF640 Gate Drain Source
STP60NF06 Gate Drain Source

PINOUTS
PARTS NAME
1 2 3
TIP31C base Collector Emiter
TIP32C base Collector Emiter

PINOUTS
PARTS NAME
1 2 3
2SA1015 Emiter Collector base
2SA965 Emiter Collector base
2SC1815 Emiter Collector base
2SC2235 Emiter Collector base
2N5401 Emiter Base Collector

21
BassLink T

22
BassLink T

23
BassLink T

24
BassLink T

25
BassLink T

26