Grade 11 Ncert Solutions - Physics

MECHANICAL PROPERTIES OF SOLIDS
NCERT QUESTIONS
1.The maximum load a wire can withstand without breaking when its length is
reduced to half of its original length, will
a) be doubled
b) be half
c) be four times
d) remain same
Answer:
The correct answer is d) remains same
2. The temperature of a wire is doubled. The Young’s modulus of elasticity
a) will also double
b) will become four times
c) will remain same
d) will decrease
Answer:
The correct answer is d) will decrease
3. A spring is stretched by applying a load to its free end. The strain produced in the
spring is
a) volumetric
b) shear
c) longitudinal and shear
d) longitudinal
Answer:
The correct answer is c) longitudinal and shear
4. A rigid bar of mass M is supported symmetrically by three wires each of length l.
Those at each end are of copper and the middle one is of iron. The ratio of their
diameter, if each is to have the same tension, is equal to
a) Ycopper/Yiron
b)
c)
d)
Answer:
The correct answer is b)
5. A mild steel wire of length 2L and cross-sectional area A is stretched, well within
elastic limit, horizontally between two pillars. A mass m is suspended from the mid-
point of the wire. Strain in the wire is
a)
b)
c)
d)
Answer:
The correct answer is a)
6. A rectangular frame is to be suspended symmetrically by two strings of equal

length on two supports. It can be done in one of the following three ways:
The tension in the strings will be

a) the same in all cases
b) least in a)
c) least in b)
d) least in c)
Answer:
The correct answer is c) least in b)
7. Consider two cylindrical rods of identical dimensions, one of rubber and the other
of steel. Both the rods are fixed rigidly at one end to the roof. A mass M is attached to
each of the free ends at the centre of the rods.
a) both the rods will elongate but there shall be no perceptible change in shape
b) the steel rod will elongate and change shape but the rubber rod will only elongate
c) the steel rod will elongate without any perceptible change in shape, but the rubber
rod will elongate and the shape of the bottom edge will change to an ellipse
d) the steel rod will elongate, without any perceptible change in shape, but the rubber
rod will elongate with the shape of the bottom edge tapered to a tip at the centre
Answer:
The correct answer is d) the steel rod will elongate, without any perceptible change in
shape, but the rubber rod will elongate with the shape of the bottom edge tapered to a tip at
the centre
Multiple Choice Questions II

1. The stress-strain graphs for the two materials are shown in the figure.
a) material (ii) is more elastic than material (i) and hence material (ii) is more brittle
b) material (i) and (ii) have the same elasticity and the same brittleness
c) material (ii) is elastic over a larger region of strain as compared to (i)
d) material (ii) is more brittle than material (i)
Answer:
The correct answers are
c) material (ii) is elastic over a larger region of strain as compared to (i)
d) material (ii) is more brittle than material (i)
2. A wire is suspended from the ceiling and stretched under the action of a weight F
suspended from its other end. The force exerted by the ceiling on it is equal and
opposite to the weight.
a) tensile stress at any cross-section A of the wire is F/A
b) tensile stress at any cross-section is zero
c) tensile stress at any cross-section A of the wire is 2F/A
d) tension at any cross-section A of the wire is F
Answer:
a) tensile stress at any cross-section A of the wire is F/A
d) tension at any cross-section A of the wire is F
3. A rod of length l and negligible mass is suspended at its two ends by two wires of
steel (wire A) and aluminium (wire B) of equal lengths. The cross-sectional areas of
wires A and B are 1.0 mm2 and 2.0 mm2 respectively.
a) mass m should be suspended close to wire A to have equal stresses in both the
wires
b) mass m should be suspended close to B to have equal stresses in both the wires
c) mass m should be suspended at the middle of the wires to have equal stresses in
both the wires
d) mass m should be suspended close to wire A to have equal strain in both wires
Answer:
b) mass m should be suspended close to B to have equal stresses in both the wires
d) mass m should be suspended close to wire A to have equal strain in both wires
4. For an ideal liquid
a) the bulk modulus is infinite
b) the bulk modulus is zero
c) the shear modulus is infinite
d) the shear modulus is zero
Answer:
a) the bulk modulus is infinite
d) the shear modulus is zero
5. A copper and a steel wire of the same diameter are connected end to end. A
deforming force F is applied to this composite wire which causes a total elongation
of 1 cm. The two wires will have
a) the same stress
b) different stress
c) the same strain
d) different strain
Answer:
a) the same stress
d) different strain
Very Short Answers

1. The Young’s modulus for steel is more than that for rubber. For the same
longitudinal strain, which one will have greater tensile stress?
Answer:
Young’s modulus is given as:
When the longitudinal strain is the same for both, steel will have a greater tensile stress
When the longitudinal strain is the same for both, steel will have a greater tensile stress
2. Is stress a vector quantity?

Answer:
Stress is a neither a scalar quantity nor a vector quantity. It is a tensor quantity. This is
because stress is equal to the magnitude of the internal reaction force divided by the area of
cross-section.
3. Identical springs of steel and copper are equally stretched. On which, more work
will have to be to done?
Answer:
When the identical springs of steel and copper are equally stretched, force is given as:
Because the springs are same, their length and area will also be the same
From both the equations, we can say that

3. What is the Young’s modulus for a perfect rigid body?
Answer:
According to Hooke’s law,
Young’s modulus = Stress/ Longitudinal strain
When the given body is a perfect rigid body, then the Young’s modulus is given as:
4. What is the Bulk modulus for a perfect rigid body?

Answer:
Bulk modulus is given as:
Bulk modulus = Stress/ Volume strain = pV/∆V
For a perfectly rigid body, bulk modulus is
B = pV/0 = ∞

Grade 11 Ncert Solutions - Physics

Uploaded by

Copyright:

Available Formats

Grade 11 Ncert Solutions - Physics

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Grade 11 Ncert Solutions - Physics

Uploaded by

Copyright:

Available Formats

MECHANICAL PROPERTIES OF SOLIDS

6. A rectangular frame is to be suspended symmetrically by two strings of equal

The tension in the strings will be

Multiple Choice Questions II

Very Short Answers

2. Is stress a vector quantity?

From both the equations, we can say that

4. What is the Bulk modulus for a perfect rigid body?

You might also like