CFD Analysis of Double Pipe Heat Exchang PDF

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 04 | Apr-2018 www.irjet.net p-ISSN: 2395-0072
CFD ANALYSIS OF DOUBLE PIPE HEAT EXCHANGER WITH DIFFERENT

INNER SECTIONS
Hariraam.V1, Domnic Edward.D2, Gokula Krishnan.M3, Dombega Shivajittu4, Selvan.P5
1,2,3,4 Studentof B.E Mechanical Engineering, SNS College of Engineering, Coimbatore, India
5 Under the Guidance of Assistant Professor, Department of Mechanical Engineering, SNS College of Engineering,
Coimbatore, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - Heat transfer techniques and thermal properties 2. INPUT PARAMETERS
of Heat Exchanger can be analyzed using Computational Fluid
Dynamics tools. There exists no analysis with varying the inner 2.1 Double pipe Heat Exchanger with Inner Circular
section, tube of double piped heat exchanger with square as a Section
substitute for conventional circular section. The methodology
for CFD analysis of a heat exchanger is validated is the effect of 2.1.1.Calculation for Inner Circular Section
fluid properties for both square and circle sections are with
constant temperature and thermal properties where analyzed. Diameter, d = 0.06m
The contour of temperature for both the circular and square Area, a =(πd2)/4
sections are calculated using ANSYS fluent 15.0, Where the =2.82×10-3 m2
equation of mass, moment and heat transfer where solved Velocity , v = 0.003m/s
simultaneously using k- epsilon two equation turbulence Hydraulic diameter, Hd = (4A/P)
mode. Thus, this research results in better selection of inner =0.06m
section for double pipe heat exchanger. Mass flow rate, m = ρ.A.V
= 0.01 kg/s
Key Words: Heat Exchanger, Computational Fluid
Dynamics, Varying Inner Sections, Circle, Square. 2.1.2.Calculation for outer section – Cylinder
1. INTRODUCTION Area, A = 7.4612×10-3 m2

Velocity, V = 0.004m/s
Heat exchanger plays an important in power plants and heat Mass flow rate, m = ρ.A.V
recovery units. Due to increasing the population, the energy = 0.029Kg/s
is efficient for our daily works. So that many heat exchangers
can be used for utilize the energy efficiently. Here analyzing
the heat transfer between two fluids such as hot and cold. In
this paper the circle and square shape of heat exchanger pipe
was analyzed for which one is maximum heat transfer rate.
The analysis is done by the computational fluid dynamics in
the software of ANSYS fluent 15.0. The flow analysis is set
between hot and cold water passing the pipe. The velocity of
hot water is less when compared to the cold water in order
to increase the heat transfer rate. The heat transfer
coefficient is critical for designing and developing the flow of
process.
1.1 Types of Heat Exchanger
There are innumerable types of heat exchangers are Fig-1: Solid Model of Double pipe Heat Exchanger with
available in use such as Tubular type heat exchanger, Plate inner Circular Tube modeled using SOLIDWORKS
type heat exchanger, Extended heat exchanger, Regenerative
heat exchanger. Here the Tubular type Double Pipe Heat 2.2.Double pipe Heat Exchanger with Inner Square
Exchanger is analyzed. Section
2.2.1 Calculation for Inner Section Square:
Hydraulic Diameter, Dh = 0.06m

Area, A = a2
© 2018, IRJET | Impact Factor value: 6.171 | ISO 9001:2008 Certified Journal | Page 1851
Perimeter, P = 4a
Side, a
0.06 = (4A/P)
0.06 = (4×a2)/4a
a = 0.06m
Mass flow rate, m = ρ.A.V
= 0.0108 Kg/s
2.2.2 Calculation for Outer section – Cylinder
Area, A = 6.409×10-3 m2
Velocity, V = 0.004m/s
Mass flow rate, m = ρ.A.V
= 0.0256Kg/s
Fig - 4: Double pipe Heat Exchanger Square Tube with
Mesh
Table – 1: Details of Mesh Model
Details Circular Square

Section Section
Nodes 33425 9900
Element 31350 9047
4. VALIDATION OF MODEL
The circular and square tube was analysed using

computational fluid dynamics for counter flow where hot
Fig-2: Solid Model of Double pipe Heat Exchanger with fluid flows through the inner pipe and the cold fluid flows
inner Square Tube modeled using SOLIDWORKS. through the outer pipe. Heat transfer parameters, such as
temperature drop was calculated. Thus simulation results
3. SOLUTION STRATEGY & CONVERGENCE were developed. The simulation results of the circular tube
were compared with the results obtained for a square tube
The mesh made is with small mesh sizes, so good gradients of equal length and similar operating conditions in order to
can be obtained in boundaries. The values in the table compare its performance related to thermal properties of
indicate the properties of circular, Square inner pipe. the heat exchangers.
Table – 2: CFD Validation Parameters
Type of Inner CIRCLE SQUARE

Section
Length 1m 1m
Hydraulic Diameter 0.06m 0.06m
Working Fluid WATER – WATER –

LIQUID LIQUID
Cold Fluid Inlet 303 K 303 K

Temperature
Hot Fluid Inlet 350 K 350 K

Fig-3: Double pipe Heat Exchanger Circular Tube with
Mesh Temperature
Mass Flow Rate 0.01 Kg/s 0.0108 Kg/s
5. RESULT
CFD computations were done for the mass flow rate of water
0.01 circular tube and 0.0108 kg/s for square tube.
Performance parameters adopted for comparison are heat
pick range by the cold fluid and heat flow rate.
The heat transfer in the circular tube in analysed in ANSYS

FLUENT as fig- 5 and the results fig - 6 are obtained.
Fig – 8: Results of Static Temperature
Table – 3: Comparison of Working Fluid Temperature
Type of Inner Section Circle Square

Cold Fluid inlet 303 K 303 K
Tempeature
Cold Fluid outlet 314.27 K 316.78 K
Tempeature
HotFluid inlet 350 K 350 K
Tempeature
Cold Fluid outlet 331.73 K 333.09 K
Fig – 5: Temperature Contour of Circular tube Tempeature
Heat Flow rate ,Q 1366.808 W 1475.274 W
From the results, the cold fluid outlet temperature is higher

in square tube than the conventional circular tube. Thus, the
Heat absorbed by the cold fluid from the hot fluid is more in
square tube than the conventional circular tube.
Fig – 6: Results of Static Temperature
The heat transfer in the square tube in analysed in ANSYS

FLUENT as fig 7and the results fig 8 are obtained.
Chart – 1: Temperature Difference of Cold Fluid (Heat

pick up range) in different inner sections.
The heat flow rate of cold fluid for circle tube is 1366.80W
Fig -7: Temperature Contour of Square tube The heat flow rate of hot fluid for square tube is 1475.27W.
The heat flow rate of cold fluid for circle tube and square
tube is plotted as a graph shows in the Chart 2.
Chart - 2: Heat Flow Rate of Cold Fluid in different inner

sections
6. CONCLUSION
Comparing with the circular and square, the heat pick rate in
the cold fluid done by the square section is more in the
counter flow. The heat flow rate is high due to high end
turbulent edges are more when compared to circle. The CFD
software have emerged as a cost effective and speedy
solution provider to heat exchanger design, analysis and
optimization. In square corners were present while the circle
has no corners, When the number of corners increases the
heat dissipation at the corners are also increases. So the net
heat flow rate also increases.
REFERENCES
1. Muhammad Mahmood Aslam Bhutta et al, CFD

applications in various heat exchangers design: A
review, Applied Thermal Engineering, 32 (2012),
Page No.1-12.
2. M.Z.M.Saqheeb Ali et al,Thermal Analysis of Double

Pipe Heat Exchanger by Changing the Materials
Using CFD, International Journal of Engineering
Trends and Technology (IJETT) – Volume 26
Number 2- August 2015 Page no. 95-102
3. Kale Shivam B et al, Experimental analysis &

Simulation of double pipe heat Exchanger, IJARIIE-
ISSN(O)-2395-4396, Vol-3 Issue-2 2017 I
4. Dr.Y.Krishna et al,CFD Analysis and Performance of

Parallel and counter flow in Concentric tube heat
Exchanger, International Journal of Engineering
Technology and research Vol-2, Issue -11,
Novermber 2017, Page No. 2782-2792.

CFD Analysis of Double Pipe Heat Exchang PDF

Uploaded by

Copyright:

Available Formats

CFD Analysis of Double Pipe Heat Exchang PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CFD Analysis of Double Pipe Heat Exchang PDF

Uploaded by

Copyright:

Available Formats

What types of heat exchangers are discussed?

What types of heat exchangers are discussed?

What parameters were used to analyze the circular and square tube heat exchangers?

What parameters were used to analyze the circular and square tube heat exchangers?

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056

Volume: 05 Issue: 04 | Apr-2018 www.irjet.net p-ISSN: 2395-0072

CFD ANALYSIS OF DOUBLE PIPE HEAT EXCHANGER WITH DIFFERENT

1. INTRODUCTION Area, A = 7.4612×10-3 m2

1.1 Types of Heat Exchanger

2.2.1 Calculation for Inner Section Square:

Hydraulic Diameter, Dh = 0.06m

2.2.2 Calculation for Outer section – Cylinder

Table – 1: Details of Mesh Model

Details Circular Square

Nodes 33425 9900

Element 31350 9047

The circular and square tube was analysed using

Table – 2: CFD Validation Parameters

Type of Inner CIRCLE SQUARE

Hydraulic Diameter 0.06m 0.06m

Working Fluid WATER – WATER –

Cold Fluid Inlet 303 K 303 K

Hot Fluid Inlet 350 K 350 K

Mass Flow Rate 0.01 Kg/s 0.0108 Kg/s

The heat transfer in the circular tube in analysed in ANSYS

Fig – 8: Results of Static Temperature

Table – 3: Comparison of Working Fluid Temperature

Type of Inner Section Circle Square

From the results, the cold fluid outlet temperature is higher

Fig – 6: Results of Static Temperature

The heat transfer in the square tube in analysed in ANSYS

Chart – 1: Temperature Difference of Cold Fluid (Heat

Chart - 2: Heat Flow Rate of Cold Fluid in different inner

1. Muhammad Mahmood Aslam Bhutta et al, CFD

2. M.Z.M.Saqheeb Ali et al,Thermal Analysis of Double

3. Kale Shivam B et al, Experimental analysis &

4. Dr.Y.Krishna et al,CFD Analysis and Performance of

You might also like