LAB # 06

Analog to Digital Conversion in

MATLAB and Simulink
INTRODUCTI0N:

Analog-to-digital conversion is an electronic process in which a continuously variable (analog)

signal is changed, without altering its essential content, into a multi-level (digital) signal. The input
to an analog-to-digital converter (ADC) consists of a voltage that varies among a theoretically
infinite number of values. Examples are sine waves, the waveforms representing human speech,
and the signals from a conventional television camera. The output of the ADC, in contrast, has
defined levels or states. The number of states is almost always a power of two -- that is, 2, 4, 8,
16, etc. The simplest digital signals have only two states, and are called binary. All whole numbers
can be represented in binary form as strings of ones and zeros.

ANALOG TO DIGITAL CONVERSION PROCESS

Analog to Digital Converter samples the analog signal on each falling or rising edge of sample
clock. In each cycle, the ADC gets of the analog signal, measures and converts it into a digital
value. The ADC converts the output data into a series of digital values by approximates the signal
with fixed precision. The below block diagram explains the analog to digital conversion process.
Figure 1: Block diagram of ADC process
SAMPLING
Sampling is the reduction of continuous signal to a discrete time representation of the original
signal .It converts analog signal into series of impulse, each representing amplitude of the signal
at given point . Sampling can be done for functions varying in space, time, or any other dimension,
and similar results are obtained in two or more dimensions. For functions that vary with time, let
s(t) be a continuous function (or "signal") to be sampled, and let sampling be performed by
measuring the value of the continuous function every T seconds, which is called the sampling
interval or the sampling period. Then the sampled function is given by the sequence: s (nT), for
integer values of n. The sampling frequency or sampling rate, fs, is the average number of samples
obtained in one second (samples per second), thus fs = 1/T.

QUANTIZATION
Quantization levels refers to the number of different sample values that can be represented in
digital quantity .There are two types of quantization in A/D process ;Routing and Truncation .In
routing ,a numerical value is replacing by another value that is approximately equal but in
truncation a numerical value is equivalent . Quantization, in mathematics and digital signal
processing, is the process of mapping input values from a large set (often a continuous set) to
output values in a (countable) smaller set. Rounding and truncation are typical examples of
quantization processes. Quantization is involved to some degree in nearly all digital signal
processing, as the process of representing a signal in digital form ordinarily involves rounding.
Quantization also forms the core of essentially all lossy compression algorithms. The difference
between an input value and its quantized value (such as round-off error) is referred to as
quantization error. A device or algorithmic function that performs quantization is called a
quantizer.

MATLAB CODE:

U=10; % range signal from 0 to 10 n=3

% number of bits
q=U/(2^n-1) % quantization interval t=0:0.1:10;
% your time vector y=abs(10*sin(t)); % your
signal
% -------convert to a digital signal yd-----------
a=fix(y/q); yd=dec2bin(a,n)
% ------you can calculate the signal yq ----------
yq=a*q
%-------------------------------------------------
plot(t,y,'r') hold on plot(t,yq,'g') hold off

SIMULINK MODEL & WAVEFORM:

TASK:

1. Perform the Analog to digital conversion as shown in above diagram in Simulink. And plot the
output results using Simulink.
2. Perform Analog To Digital Conversion Using Sampling Theorem.
3. i) Construct a sinusoidal signal. Specify a sample rate such that 16 samples correspond to exactly
one signal period. Draw a stem plot of the signal. Overlay a stairstep graph for sample-and-hold
visualization.
ii) Up-sample the signal by a factor of four. Plot the result alongside the original signal.
Upsample increases the sample rate of the signal by adding zeros between the existing samples.
 Levels
PLO
no Criteria Beginning (1) Developing (2) Accomplished (3) Exemplary (4)

Student is unable to apply With instructor/ supervisor’s With instructor/ Student is able to apply all
Apply Procedural
described procedure to guidance, student is able to supervisor’s guidance, procedural knowledge to
Knowledge to
1 perform activity despite apply some of the described student is able to apply all independently perform
perform an
instructor/ supervisor’s procedure to partially perform described procedure to fully activity without instructor/
activity
guidance. activity. perform activity. supervisor’s guidance.
With instructor/ Student is able to
Student is unable to design
Design systems, With instructor/ supervisor’s supervisor’s guidance, independently design
systems, components and/or
components guidance, student is able to student is able to fully systems, components and/or
processes to meet
3 and/or processes partially design systems, design systems, processes to meet
specifications despite
to meet components and/or processes components and/or specifications without
instructor/ supervisor’s
specifications to meet specifications. processes to meet instructor/ supervisor’s
guidance.
specifications. guidance.
With instructor/ Student is able to
Student is unable to analyze/ With instructor/ supervisor’s
Data Analysis and supervisor’s guidance, independently
interpret obtained results guidance, student is able to
4 interpretation of student is able to fully analyze/interpret obtained
despite instructor/ partially analyze/interpret
obtained results analyze/interpret obtained results without instructor/
supervisor’s guidance. obtained results.
results. supervisor’s guidance.
Operational Skills Student has shown little to no
for ability to handle/use With instructor/ supervisor’s With instructor/ Student can handle/use all
Hardware/Softwa equipment/software and guidance, student can supervisor’s guidance, equipment/software and
5 re equipment and involved components despite handle/use some of the student can handle/use all involved components
involved instructor/ supervisor’s equipment/ software and equipment/software and without instructor/
components guidance. involved components. involved components. supervisor’s guidance.
 Student has shown little to no
regard for personal and With instructor/ supervisor’s With instructor/ Student has followed all
Follow personal
equipment safety regulations guidance, student followed supervisor’s guidance, safety rules and protocols
6 and equipment
despite instructor/ some of the personal and student followed all safety without instructor/
Safety Rules
supervisor’s guidance. equipment safety regulations rules. supervisor’s guidance.

Psychomotor Domain Rubrics

Activity Name  EXPERIMENT No. 6

Group No. 

Student Roll No.  12438

C P Domain +
N L L Taxonomy Criteria Awarded Score (out of 4 for each cell)
o. O O

Operational Skills for Hardware/Software equipment and

1 6 1 P3 involved components

2 5 10 A3 Effectively reported the activity performed in lab

- - - -

Total
-