AP1682E (Isolated Flyback Design) Cal

Please fill the electrical parameters(Red), this tool will calculate the component values(B

Step 1: Input Electrical Parameters

Design Spec.
Min Input AC Voltage(Vac_min) 85.0 Vac
Max Input AC Voltage(Vac_max) 265.0 Vac
AC Line Frequency 50.0 Hz
Min Switching Frequency @ Full Load 70.0 Khz
Total Power Conversion Efficiency (ηp) 88.0 %
Power Factor 0.95

Step 2: Input Transformer Turns Ratio

Key Operation Parameters Selection
Transformer Conversion Efficiency (ηt) 95%
Customrized Max Vs/Vpk (Kp) 1.00 Always 1 for Flyback
Peak Value of Kc=Tons/Tsw @ Kp=1 0.444
Max Tons/Tsw 0.444

Design Data
Min Peak Value of DC Bus Voltage(Vdc_min) 120.19 Vdc
MOSFET Voltage Stress Vds_max 529.51 Vdc
Max MOSFET Peak Current Value(Ippk) 1.04 A
Max MOSFET RMS Current Value (Iprms) 0.196 A

Current Sense Resistor

Current Sense Resistor Value Rcs= 0.96 Ω User adjustable
Power Loss of Rcs (Prcs)= 37 mWalt
Step 3: Input Customarized Inductance (keep the value close to the
Step 4: Input Maximum Flux Density Bmax, then input Ae according to th
Transformer Design
Maximum Flux Density Bmax 0.30 T
Calculated Inductor Inductance (Lp)= 0.35 mH
Ferrite Core Shape Ttype= EDR2610
Primary Winding Turns Number Np= 20 Ts
Secondary Winding Truns Number Ns= 7 Ts
Aux Winding Truns Number Nf= 7 Ts
Current density selection 6.00 A/m㎡
primary Winding diameter selection 0.26 mm
Secondary Winding diameter selection 0.40 mm
Step 5: Input Vpk pull up Resistor value
Vpk Sense Resistor Design
Divider Proportion (Kpk) 0.0125777268 Max Voltage on Vpk Pin 3.0

Vs Sense Resistor Design

Divider Proportion (Ks) 0.0080061915 Max Voltage on Vs Pin 3.0

Step 6: Input Ton_delay and CS Pin Resistor va

Line Compensation
Turn off System Delay Time_tdely= 80 nS
CS Pin Resistor (R12) 2.0 KΩ

Start-Up Resistor
Start-Up Time (Ton_d) 500 mS
Start-Up Resistor R8+R9+R10= 2.53 MΩ
Power loss_Prst= 35.11 mWalt
Step 7: Input Pull-Up Resistor R16 value
FB Sense Resistor
Resistor Divider Ratio_Ka= 0.18

Vout Capacitor
Max Capacitor Voltage Vout_max 27 Vdc
ck Design) Calculator - version 1.6

component values(Blue), and system parameters(Pink)

ctrical Parameters
LED Load Spec.
LED Cell Forward Voltage (Vf) 20.00 Vdc
LED Current (Iled) 300.00 mA
LED Cell Numbers in Serials(Qsled) 1.00 Pcs F1 DB1
LED Chain Numbers in Parallel(Qpled) 1.00 Pcs
Vout 20.00 Vdc AC C1
VR1
input
Iout 300.00 mA
Output Power (Pout) 6.00 Walt
Outpur Current Ripple (Io_ripple_pp) 180.00 mA
LED Load Dynamic Resistance (ΔVo/Δio) 2.00 ohm R2

sformer Turns Ratio

L2
Permittable Max Transformer Turns Ratio Nt 7.14
Customerized Transformer Turns Ratio Nt 2.74
Max Peak Current Reference Vcs 1.00 V

Max Peak Value of DC Bus Voltage(Vdc_max) 374.71 Vdc

Rectify Diode Voltage Stress Vsd_max 166.76 Vdc
Max Diode Peak Current Value(Ispk) 2.70 A
Max Diode Average Current Value(Isdc) 0.300 A
Max Diode RMS Current Value (Isrms) 0.677 A

User adjustable

p the value close to the Calculated Inductance)

nput Ae according to the selected ferrite core shape

Auxiliary winding voltage design Vcc= 20.00 V

Customarized Inductance Lp= 0.35 mH
Effective Area of Ferrite Core Ae= 0.620 c㎡
Max Primary Winding RMS Current Value (Itprms) 0.196 A
Max Secondary Winding RMS Current Value (Itprms) 0.677 A
 Number strands of primary winding 0.61
Number strands of Secondary winding 0.90

pull up Resistor value

Vpk Pin Pull-Up Resistance (R3+R4)= 2000.00 KΩ

Vpk Pin Pull-Down Resistance (R6+R5)= 25.48 KΩ

Resistor between Vs pin and GND R6= 16.22 KΩ

Resistor between Vs pin and Vpk R5= 9.26 KΩ
and CS Pin Resistor value

Line Compensatin Resistor (R20) 5 MΩ

Customarize R8+R9+R10= 2.00 MΩ

For safty issue, Pls use 2Pcs 1MΩ_1206
Up Resistor R16 value

Pull-Up Resistor R16= 47 KΩ

Pull-Down Resistor Rl7= 10 KΩ

Min Capacitance Cout_min 1061 uF

 T1
L1 C6 R19
D3
1
R3 R8 R20 ZD2
R1 +
D2 5 OUT
C2 R9 C7
F1 R18
DB1 R4 R10 D1 R15 3
ZD1
AC C1
VR1
input C5 R16
R7 8-VCC 5-FB 4
3-Vpk CY1
R5 R17
C4 R11
7-OUT
R2 2-Vs
4-CS Q1
6-GND
R12

L2 R6 C3 U1 AP1682 R13 R14

 CORE參數對照表

MATE- AL
TYPE RIAL Dimensions (mm) Ap Ae Aw Le Ve

A * B * C ( cm4 ) ( mm2 ) ( mm2 ) (nH/N2) ( mm ) ( mm3 )

TYPE EC CORE
EC35 3C85 35.3*17.3*9.5 1.3741 84.30 163.00 2100.0 77.40 6530.0
EC41 3C85 41.6*19.5*11.6 2.5894 121.00 214.00 2700.0 89.30 10800.0
EC52 3C85 52.2*24.2*13.4 5.5980 180.00 311.00 3600.0 105.00 18800.0
EC70 3C85 71.7*34.5*16.4 17.8281 279.00 639.00 3900.0 144.00 40100.0
TYPE EE CORE
EE05 PC40 5.25*2.65*1.95 0.0013 2.63 5.00 285.0 12.60 33.1
EE6.3 PC40 6.1*2.85*7.95 0.0015 3.31 4.46 405.0 12.20 40.4
EE8 PC40 8.3*4.0*3.6 0.0091 7.00 13.05 590.0 19.47 139.0
EE10/11 PC40 10.2*5.5*4.75 0.0287 12.10 23.70 850.0 26.60 302.0
EE13 PC40 13.0*6.0*6.15 0.0570 17.10 33.35 1130.0 30.20 517.0
EE16 PC40 16*7.2*4.8 0.0765 19.20 39.85 1140.0 35.00 672.0
EE19 PC40 19.1*7.95*5.0 0.1243 23.00 54.04 1250.0 39.40 900.0
EE19/16 PC40 19.29*8.1*4.75 0.1191 22.40 53.15 1350.0 39.10 882.0
EE20/20/5 PC40 20.15*10*5.1 0.1191 31.00 50.70 1460.0 43.00 1340.0
EE22 PC40 22*9.35*5.75 0.1191 41.00 38.79 2180.0 39.40 1610.0
EE2329S PC40 23*14.7*6 0.1191 35.80 122.00 1250.0 64.90 2320.0
EE25/19 PC40 25.4*9.46*6.29 0.1191 40.00 78.20 2000.0 48.70 1940.0
EE25.4 PC40 25.4*9.66*6.35 0.1191 40.30 78.73 2000.0 48.70 1963.0
EE2825 PC40 28*12.75*10.6 0.1191 86.90 98.10 3300.0 57.70 5010.0
EE30 PC40 30*13.15*10.7 0.1191 109.00 73.35 4690.0 57.70 6310.0
EE30/30/7 PC40 30.1*15*7.05 0.1191 59.70 124.87 2100.0 66.90 4000.0
EE3528 PC40 34.6*14.3*9.3 0.1191 84.80 158.00 2600.0 69.70 5910.0
EE40 PC40 40*17*10.7 0.1191 127.00 173.23 4150.0 77.00 9810.0
EE4133 PC40 41.5*17*12.7 0.1191 157.00 180.00 4200.0 79.00 12470.0
EE42/21/15 PC40 42*21.2*15 0.1191 178.00 278.00 3800.0 97.90 19510.0
EE42/21/20 PC40 42*21.2*20 0.1191 235.00 275.00 5000.0 97.80 23000.0
EE47/39 PC40 47.12*19.63*15.62 0.1191 242.00 196.40 6660.0 90.60 21930.0
EE50 PC40 50*21.3*14.6 0.1191 226.00 253.73 6110.0 95.80 21600.0
EE55/55/21 PC40 55.15*27.5*20.7 0.1191 354.00 386.34 7100.0 123.00 43700.0
EE57/47 PC40 56.57*23.6*18.8 0.1191 344.00 282.36 8530.0 102.00 35100.0
EE60 PC40 60*22.3*15.6 0.1191 247.00 399.02 5670.0 110.00 27100.0
EE50.3 PC40 50.3*25.6*6.1 0.1191 120.85 152.64 2900.0 104.90 12676.0
EE62.3/62/6 PC40 62.3*31*6.1 0.1191 153.01 198.22 3100.0 125.74 19240.0
EE65/32/27 PC40 65.15*32.5*27 0.1191 535.00 575.00 8000.0 147.00 78700.0
TYPE EF CORE
EF12.6 PC40 12.7*6.4*3.6 0.0311 13.00 23.90 810.0 29.60 385.0
EF16 PC40 16.1*8.05*4.5 0.0800 20.10 39.82 1100.0 37.60 754.0
EF20 PC40 20*9.9*5.65 0.1013 33.50 30.24 1570.0 44.90 1500.0
EF25 PC40 25.05*12.55*7.2 0.2376 51.80 45.87 2000.0 57.80 2990.0
EF32 PC40 32.1*16.1*9.15 0.6515 83.20 78.30 2590.0 74.30 6180.0
TYPE EFD CORE
EFD10 3F3 10.5*5.2*2.7 0.0084 7.20 11.60 500.0 23.70 171.0
EFD12 3F3 12.5*6.2*3.5 0.0187 11.40 16.38 700.0 28.50 325.0
EFD15 3F3 15*7.5*4.65 0.0470 15.00 31.35 780.0 34.00 510.0
EFD20 3C85 20*10*6.65 0.1550 31.00 50.00 1300.0 47.00 1460.0
EFD25 3C90 25*12.5*9.1 0.3938 58.00 67.89 2200.0 57.00 3300.0
EFD30 3C90 30*15*9.1 0.6028 69.00 87.36 2100.0 68.00 4700.0
TYPE EI CORE
EI12.5 PC40 12.4*7.4*4.85 0.0235 14.40 16.32 1200.0 21.30 308.0
EI16 PC40 16.0*12.2*4.8 0.0839 19.80 42.37 1100.0 34.60 670.0
EI19 PC40 20*13.55*5.0 0.1305 24.00 54.36 1400.0 39.60 950.0
EI22 PC40 22.0*14.55*5.75 0.1606 42.00 38.24 2400.0 39.30 1630.0
EI25 PC40 25.3*15.55*6.75 0.3165 41.00 77.19 2140.0 47.00 1927.0
EI22/19/6 PC40 22.0*14.7*5.75 0.1980 37.00 53.50 2000.0 41.80 1550.0
EI28 PC40 28.0*16.75*10.6 0.6005 86.00 69.83 4300.0 48.20 4145.0
EI30 PC40 20.0*21.25*10.7 0.8207 111.00 73.94 4690.0 58.00 6440.0
EI33/29/13 PC40 33.0*23.75*12.7 1.5854 118.50 133.79 4400.0 67.50 8002.0
EI35 PC40 35.0*24.25*10.0 1.3343 101.40 131.59 3800.0 67.10 6804.0
EI3530 PC40 35.0*24.2*12 1.6592 122.00 136.00 3950.0 68.00 8350.0
EI40 PC40 40.0*27.25*11.65 2.3301 148.00 157.44 4860.0 77.00 11300.0
EI50 PC40 50.0*33.35*14.6 5.5218 230.00 240.08 6110.0 94.00 21600.0
EI60 PC40 60.0*35.85*15.6 9.8024 247.00 396.86 5670.0 109.00 27100.0
EI70 PC40 70.0*54.0*31.6 37.7618 698.00 541.00 10500.0 145.00 101530.0
TYPE EP CORE
EP7 3C85 9.4*3.75*6.5 0.0102 10.70 9.50 1120.0 15.50 165.0
EP10 3C85 11.5*5.1*7.6 0.0255 11.30 22.57 1025.0 19.30 215.0
EP13 3C85 12.8*6.5*9.0 0.0456 19.50 23.40 1475.0 24.20 472.0
EP17 3C85 18.0*8.4*11.0 0.1210 33.70 35.90 2230.0 29.50 999.0
EP20 3C85 24*10.7*15 0.4997 78.70 63.50 3950.0 41.10 3230.0
TYPE EPC CORE
EPC10 PC44 10.2*4.05*3.4 0.0072 9.39 7.69 1000.0 17.80 167.0
EPC13 PC44 13.3*6.6*4.6 0.0288 12.50 23.00 870.0 30.60 382.0
EPC17 PC44 17.6*8.55*6 0.0426 22.80 18.70 1150.0 40.20 917.0
EPC19 PC44 19.1*9.75*6 0.1235 22.70 54.40 940.0 46.10 10473.0
EPC25 PC44 25.1*12.5*8 0.3967 46.40 85.50 1560.0 59.20 2748.0
EPC25B PC44 25.1*11.43*6.5 0.2068 33.30 62.10 1560.0 46.20 1539.0
EPC27 PC44 27.1*16*8 0.5897 54.60 108.00 1540.0 73.10 3995.0
EPC30 PC44 30.1*17.5*8 0.7137 61.00 117.00 1570.0 81.60 5035.0
TYPE ER CORE
ER9.35 TP4 9.35*2.35*4.6 0.0059 8.20 7.24 1270.0 13.70 111.8
ER9.5 PC44 9.5*2.45*5.9 0.0054 8.47 6.40 610.0 14.20 120.0
ER11.5 PC44 10.83*2.45*4 0.0078 11.70 6.67 870.0 14.00 174.0
ER14.5 PC44 14.5*2.95*6.7 0.0190 17.60 10.80 1280.0 19.00 333.0
ER1916 TP4 19.2*16*5.6 0.1985 28.80 68.93 1140.0 54.90 1584.1
ER25.5 PC40 25.5*9.3*7.5 0.3557 44.80 79.40 1920.0 48.20 2160.0
ER25/51 TP4 25.4*25.4*18 0.0734 52.80 13.91 4330.0 27.20 1435.7
ER28/28 PC40 28.55*14*11.4 0.9359 82.10 114.00 2870.0 64.00 5257.0
ER28/34 PC40 28.55*16.9*11.4 1.2047 81.40 148.00 2520.0 75.50 6143.0
ER30/16 TP4 30*8*20 0.8546 107.50 79.50 4500.0 45.00 4833.8
ER30/35 TP4 30*17.5*11.2 1.3569 85.50 158.70 2160.0 75.40 6673.0
ER35/34 TP4 35*16.8*11.3 1.6178 107.00 151.20 3000.0 72.80 7790.0
ER35/41 PC40 35*20.7*11.3 2.3326 107.00 218.00 2770.0 90.80 9682.0
ER39/36 B1 39.1*17.8*12.5 2.7713 125.00 221.70 3850.0 84.00 10530.0
ER39/42 B1 39.1*21.1*12.5 3.4975 125.00 279.80 3200.0 96.00 12000.0
ER40/45 PC40 40*22.4*13.3 3.7101 149.00 249.00 3620.0 98.00 14587.0
ER42/15 PC40 42*22.4*15.5 4.3262 194.00 223.00 4690.0 98.80 19163.0
ER42/20 PC40 42.15*21.2*19.6 5.4960 240.00 229.00 5340.0 98.60 23635.0
ER49/54 N27 49*27*17.2 9.0153 243.00 371.00 3500.0 118.00 28700.0
ER54/36 3C85 53.5*18.3*17.95 3.1500 250.00 126.00 6100.0 91.80 23000.0
TYPE ETD CORE
ETD19 PC40 19.6*13.65*7.4 0.2912 41.30 70.50 1720.0 54.60 22530.0
ETD24 PC40 24.4*14.45*8.5 0.5743 56.30 102.00 2125.0 61.90 3480.0
ETD29 PC40 29.8*15.8*9.5 1.0687 73.60 145.20 2500.0 70.60 5193.0
ETD34 PC40 34.2*17.3*10.88 1.8255 97.10 188.00 2780.0 78.60 7640.0
ETD39 PC40 39.1*19.8*12.58 3.2125 125.00 257.00 3150.0 92.10 11500.0
ETD44 PC40 44*22.3*14.9 5.3375 175.00 305.00 4000.0 103.00 18000.0
ETD49 PC40 48.7*24.7*16.4 7.9875 213.00 375.00 4440.0 114.00 24200.0
ETD54 N27 54.5*27.8*19.3 11.5360 280.00 412.00 4200.0 127.00 35600.0
ETD59 N27 59.8*31.2*22.1 17.4064 368.00 473.00 5000.0 139.00 51200.0
TYPE LP CORE
LP22/13 PC44 25*11.2*12.9 0.5717 67.90 84.20 3310.0 49.00 3277.0
LP23/8 PC44 16.5*11.7*8.7 0.1853 31.30 59.20 1600.0 44.10 1377.0
LP32/13 PC44 25*15.9*12.9 0.8809 70.30 125.30 2630.0 64.00 4498.0
TYPE RM CORE
RM4 PC40 10.8*5.2*4.45 0.0218 14.00 15.60 680.0 22.70 318.0
RM5 PC40 14.3*5.2*6.6 0.0431 23.70 18.20 1250.0 22.40 530.0
RM6 PC40 17.6*6.2*8 0.0952 36.60 26.00 1600.0 28.60 1050.0
RM8 PC40 22.75*8.2*10.8 0.3130 64.00 48.90 1950.0 38.00 2430.0
RM10 PC40 27.85*9.3*13.25 0.6811 98.00 69.50 3630.0 44.00 4310.0
RM12 PC40 36.75*11.7*16 1.5400 140.00 110.00 4150.0 56.90 7960.0
RM14 PC40 41.6*14.4*18.7 2.9140 188.00 155.00 4600.0 69.00 13000.0
TYPE PTS CORE
PTS14/8 3C85 14.05*4.15*9.4 0.0374 17.00 22.00 1750.0 22.50 495.0
PTS18/11 3C85 18*5.3*11.94 0.1067 37.20 28.67 2400.0 28.70 1070.0
PTS23/11 3C85 22.9*5.5*15.2 0.1846 57.20 32.28 3560.0 31.60 1810.0
PTS23/18 3C85 22.9*9*15.2 0.3610 58.30 61.92 2900.0 45.10 2630.0
PTS30/19 3C85 30*9.4*20.2 0.8864 111.00 79.86 4140.0 50.20 5570.0
TYPE PQ CORE
PQ20/16 PC44 20.5*8.1*14 0.2914 62.00 47.00 3880.0 37.40 2310.0
PQ20/20 PC44 20.5*10.1*14 0.4080 62.00 65.80 3150.0 45.70 2790.0
PQ26/20 PC44 26.5*10.1*19 0.7188 119.00 60.40 6170.0 46.30 5490.0
PQ26/25 PC44 26.5*12.37*19 0.9971 118.00 84.50 5250.0 55.50 6530.0
PQ32/20 PC44 32*10.27*22 1.3736 170.00 80.80 7310.0 55.50 9420.0
PQ32/30 PC44 32*15.17*22 2.4086 161.00 149.60 5140.0 74.60 11970.0
PQ35/35 PC44 35.1*17.37*26 4.3238 196.00 220.60 4860.0 87.90 19260.0
PQ40/40 PC44 40.5*19.87*28 6.5526 201.00 326.00 4300.0 101.90 20450.0
PQ50/50 PC44 50*24.97*32 14.2024 328.00 433.00 6720.0 113.00 37238.0
TYPE UU CORE
UU8.5 PC40 8.5*6.35*3.45 0.0251 7.76 32.30 560.0 31.40 243.0
UU9.8 PC40 9.8*7.1*2.7 0.0269 7.65 35.20 500.0 34.10 261.0
UU10.1 HS72 10.1*7.5*2.9 0.0327 8.60 38.00 515.0 35.70 300.0
UU10.5 HS72 10.5*7.9*5 0.0737 12.40 59.40 720.0 40.50 505.0
UU13.5 PC40 13.5*9.9*5 0.1374 16.30 84.30 800.0 49.20 803.0
UU15.22 PC40 15.2*11.2*6.7 0.2044 32.50 62.90 1400.0 50.50 1640.0
UU15.23 PC40 15.2*11.4*6.4 0.2121 31.90 66.50 1360.0 51.70 1650.0
UU15.7 HS72 15.7*9.7*6 0.2083 24.80 84.00 1100.0 50.00 1310.0
UU17 PC40 17*16.6*6 0.5165 26.90 192.00 750.0 78.30 2100.0
UU19.7 HS72 19.7*17.7*6 0.6948 36.00 193.00 980.0 83.20 2990.0
UU21 PC40 20.8*15.8*7.7 0.5616 54.00 104.00 1760.0 68.60 3700.0
UU25 PC40 25*14*7 0.7546 49.00 154.00 1530.0 72.00 3520.0
Wt PCL 100kHz Pt 幅寬 窗口面
100 mm 积 PIN 形狀
200mT kHz mm2
( g ) @100℃(W) (W) 可配合BOBBIN

38.00 21.5 8 H
60.00 24.5 8 H
112.00 28.3 12 H
254.00 41.4 12/34 H

0.16 0.02 1.1 2.7 6-8 H

0.24 0.02 2.7 6 H
0.70 0.06 1.9 4.78 5.3 6 H
1.50 0.16 6.6 12.2 8 V
2.70 0.235 7.4 22.2 10 V
3.30 0.31 8.5 27.3 6-10 V H
4.80 0.42 9 33.1 6-8 V H
4.80 0.41 9 33.1 6-8 V H
7.50 0.51
8.80 0.61 8.45 20 8 V
12.00 1.16
9.10 0.9 9.8 42.5
10.00 0.9
26.00 2.51 9.6 39.4 10 V
32.00 2.9 13.7 43.2 10-12 V
22.00 1.51
29.00 2.96 15.7 88.7 12 V
50.00 4.2 17.3 108 12 V
64.00 6.25
88.00 8.8
116.00 11.6
108.00 9.7
116.00 9.4 21.3 170 12 V
234.00 11.0(150MT)
190.00 8.5
135.00 12.5 23.8 294 12 V
68.00 5.83 28.25 96.05 12 H
102.00 8.85 33.85 115.09 12 H
399.00 5.9(100MT)

2.00 0.17 3.5 10 V

3.90 0.32
7.40 0.69
15.00 1.4
32.00 2.9

0.45 0.02 6 8 H
0.90 0.04 7.6 8 H
1.40 0.06 8.8 8 H
3.50 0.27 13 8 H
8.00 0.38 16.4 43.4 10 H
12.00 0.54 20.1 12 H

1.90 0.12 3.5 8.6 10 V

3.30 0.31 8.5 27.3 6-10 H V
5.10 0.42 9.05 36.4 6-8 H V
9.80 0.6 8.45 20 1/7/1900 V
9.80 0.79 9.8 42.5 8 V
8.50 0.64 8.45 31.5 1/7/1900 V
22.00 1.65 9.6 39.4 10 V
34.00 3.1 13.7 44.5 10-12 V
41.00 3.5 16.6 88.8 12 V
36.00 2.85 15.7 88.7 1/11/1900 V
43.00 4.2
60.00 4.8 17.3 108 1/11/1900 V
115.00 9.2 21.3 170 12 V
139.00 1.25 23.8 294 1/11/1900 V
519.00 7.61(100MT)

0.80 0.03 3.4 6 H

1.10 0.04 5.6 8 H
2.40 0.09 7.6 10 H
5.00 0.16 9.45 8 H
16.00 0.5 12.45 10 H

1.10 0.072 5.4

2.10 0.14 8.6 6.9 10 H
4.50 0.35 20
5.30 0.4 27 12.2 12 H
13.00 1.11 63 14.7 12 H
11.00 0.65 45 14.7 12 H
18.00 1.56 80 20.5 12 H
23.00 2.03 85 22.8 12 H

0.55
0.60 3.9 2.2 8 V
0.85 5.0 1.9 10 V
1.00 9.5 1.9 10
1.80
11.00 0.98 87 10.6 48.4 10 V
8.10
28.00 2.3 203 16.1 71.8 10--12 H V
33.00 2.7 228 21.8 96.3 10--12 H V
25.00
32.00
51.00 26.4 152.7 12 V
52.00 4.2 325 26.1 154.4 12--16 V
56.00 28.2 12 V
57.10 28.4 16 V
78.00 6.3 421 27.8 178.8 16 V
102.00 8.6 433 27.8 153.3 16 V
116.00 10.7 509 27.3 159.7 16 H
146.00 167.8
61.00 3.8 31 18 V

13.30 1.1 79 37.4

19.50 1.6 115 44.7
28.00 2.4 170 19.7 13 H
40.00 3.55 271 21.5 14 H
60.00 5.3 382 26 16 H
94.00 8.3 523 30 18 H
124.00 11.2 682
180.00 26
260.00

21.00 1.3 121

9.60 0.52 50
30.00 1.7 164

1.70 0.08 6.9 5.9 4-6 V

3.00 0.18 16 4.9 4-6 V
5.50 0.41 27 6.4 4-6 V
13.00 0.97 67 9.15 8-12 V
23.00 1.8 130 10.75 10-12 V
42.00 3.3 344 14.8 11-12 V
70.00 4.75 376 18.8 10-12 V

2.50 4 12 V
5.00 0.19(25kHZ) 6 6 V
9.00 0.28(25kHZ) 5.16 10 V
13.00 0.41(25kHZ) 11.76 10 V
30.00 0.87(25kHZ) 10.8 10 V

13.00 0.84 70 11.9 12 V

15.00 1.02 92 11.9 12 V
31.00 1.94 170 13.6 12 V
36.00 2.32 195 13.6 12 V
42.00 2.92 232
55.00 3.92 331 18.5 12 V
73.00 5.27 452
95.00 6.56 596
195.00 6.4 1045
1.20 0.12
1.30 0.14
1.50 0.15
2.50 0.26
4.00 0.4
8.50 0.83
8.60 0.83
6.70 0.66
10.00 1.06
15.00 1.5
19.00 1.86
18.00 1.77