Designation: D 391 – 94 (Reapproved 2000)e1 An American National Standard

Standard Specification for

Creosote-Coal Tar Solution1
This standard is issued under the fixed designation D 391; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.

This standard has been approved for use by agencies of the Department of Defense.

e1 NOTE—Editorial changes were made in March 2000.

1. Scope D 368 Test Method for Specific Gravity of Creosote and

1.1 This specification covers creosote-coal tar solution for Oil-Type Preservatives2
use in the preservative treatment of wood. D 369 Test Method for Specific Gravity of Creosote Frac-
1.1.1 Test Method D 38 covers the sampling of wood tions and Residue2
preservatives prior to testing. D 370 Test Method for Dehydration of Oil-Type Preserva-
tives2
2. Referenced Documents
3. Composition and Properties
2.1 ASTM Standards:
D 38 Test Methods for Sampling Wood Preservatives Prior 3.1 Creosote-coal tar solution shall be a pure coal tar
to Testing2 product derived entirely from tar produced by the carboniza-
D 95 Test Method for Water in Petroleum Products and tion of bituminous coal. It shall be either a coal tar distillate or
Bituminous Materials by Distillation3 a solution of coal tar in coal tar distillate, and shall conform
D 168 Test Method for Coke Residue of Creosote2 with the requirements for the respective grades specified in
D 246 Test Method for Distillation of Creosote and Table 1.
Creosote-Coal Tar Solutions2
4. Sampling and Test Methods
D 347 Tables for Volume and Specific Gravity Correction
for Creosote, Creosote-Coal Tar Solution and Coal Tar2 4.1 The material shall be sampled and the properties enu-
D 367 Test Method for Xylene-Insoluble Matter in Creo- merated in this specification shall be determined in accordance
sote2 with the following methods:
4.1.1 Sampling—Test Methods D 38.
1
4.1.2 Water—Test Method D 370, or as an alternative
This specification is under the jurisdiction of ASTM Committee D-7 on Wood,
and is the direct responsibility of Subcommittee D07.06 on Treatments for Wood method, Test Method D 95.
Products. 4.1.3 Xylene Insoluble Matter—Test Method D 367.
Current edition approved July 15, 1994. Published September 1994. Originally 4.1.4 Specific Gravity—Test Method D 368.
published as D 391 – 39 T. Last previous edition D 391 – 84.
This specification is essentially the same as the specifications for grades A, B,
4.1.5 Distillation—Test Method D 246.
and C of the American Wood-Preservers’ Association Standard for Creosote-Coal 4.1.6 Specific Gravity of Fractions—Test Method D 369.
Tar Solutions (P2 – 68), except for the distillation range of used solutions. The 4.1.7 Coke Residue—Test Method D 168.
marine grade table is not identical to the American Wood Preservers’ Association 4.1.8 Volume and Specific Gravity Correction—Test
Standard for Creosote-Coal Tar Solution to be used in the treatment of marine
(coastal waters) piles and timbers (P12 – 68). Acknowledgment is made to the
Method D 347.
American Wood-Preservers’ Association for its development of the subject matter
covered in this standard. 5. Keywords
2
Annual Book of ASTM Standards, Vol 04.10. 5.1 coal tar; creosote
3
Annual Book of ASTM Standards, Vol 05.01.

Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.

--`,,```,,,,````-`-`,,`,,`,`,,`---

Copyright ASTM International 1

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS Not for Resale
 D 391
TABLE 1 Composition and Properties
Land and Fresh Water Grades Marine Grade
Grade A Grade B Grade C
Min Max
Min Max Min Max Min Max
Coal tar distillate, volume % 80 ... 70 ... 60 ... ... ...
Specific gravity at 38°C compared with water at 15.5°C 1.06 1.11 1.07 1.12 1.08 1.13 1.090 ...
Water, volume % ... 3.0 ... 3.0 ... 3.0 ... 3.0
Xylene insoluble matter, weight %A ... 2.0 ... 3.0 ... 3.5 1.0 3.0
Coke residue, weight %A ... 5.0 ... 7.0 ... 9.0 4.0 7.0
Distillation—percentage of distillate by weight on water-
free basis:
Up to 210°C ... 5 ... 5 ... 5 ...
Up to 235°C 25 25 25 5
Up to 270°C ... ... ... ... ... ... 20 15
Up to 315°C 36 ... 34 ... 32 ... 35 35
Up to 355°C 60 ... 56 ... 52 ... 55 50
Specific gravity of fractions at 70
38/15.5°C:
235 to 315°C 1.025 ... 1.025 ... 1.025 ... 1.030 ...
315 to 355°C 1.085 ... 1.085 ... 1.085 ... 1.110 ...
Specific gravity of distillation residue at 38/15.5°C ... ... ... ... ... ... 1.185 ...
A
Due to treating operations.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection
with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your
views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at
610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website (www.astm.org).

--`,,```,,,,````-`-`,,`,,`,`,,`---

Copyright ASTM International 2

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS Not for Resale