Samsung 940bw Plus

3 Alignments and Adjustments

This section of the service manual explains how to use the DDC Manager JIG.
This function is needed for AD board change and program memory (IC201) change.
3-1 Required Equipment

The following equipment is necessary for adjusting the monitor:
- Computer with Windows 95, Windows 98, Windows 2000, Windows XP or Windows NT.
- MTI-2055, 2058, or 2059 DDC MANAGER JIG
3-2 Automatic Color Adjustment

To input video, use 16 gray or any pattern using black and white.
1. Select english for OSD language.
2. Press the " (Enter/Source)" key for 5 seconds.
3-3 DDC EDID Data Input

1. Input DDC EDID data when replacing AD PCB.
2. Receive/Download the proper DDC file for the model from HQ quality control department.
Install the below jig (Figure 1) and enter the data.
MTI-2055
DDC Manager
Parallel Connector
(25P Cable)
Connect Monitor
(Signal Cable)
Figure 1.
3-4 OSD Adjustment When Replacing Panel
1. Adjust brightness and contrast to 0. Then, press the (Enter/Source) key for 5 second.
Service function OSD will appear on screen.
2. Press the + key to place the cursor on the panel. Press the menu key for 5 seconds.
3-5 OSD Adjustment When Replacing Lamp Only

1. Adjust brightness and contrast to 0. Then, press the exit key for 5 seconds.
Service function OSD will appear on the screen.
2. Press the + key. Select upper lamp and press the menu key for 5 seconds.
Then, select lower lamp and press the menu key for 5 seconds.
-Note : Please be sure to read the following instructions for details on service function.
3-1
3-6 Service Function Spec.

3-6-1 How to Display Service Function OSD
1. The value for brightness and contrast should be changed to zero.
2. Within 5 seconds, press the (Enter/Source) key.
3. Service function OSD will be displayed.
- If you want to disable the service function OSD, you will have to power off.
Panel Information
Softward Version
Checksum
Figure 2. The example of service function OSD
The service function OSD is based on a grid of 29 columns x 12 rows.

The service function OSD consists of panel information, software version and MICOM checksum.
3-6-2 How to Control Service Function OSD

1. With the panel selected on OSD, whenever you press the right key, the base color will change to blue from
"Panel" to "Upper Lamp", "Lower Lamp".
Figure 3.
3-2

After change the panel or lamp, you must reset service function OSD.
The case of panel change
After changeing the panel, press the menu key within 5 seconds,.
Then, panel Ch. No increases one step and the panel time information is reset to zero.
Simultaneously, other information is reset to zero (Upper/Lower lamp, Panel cycle).
Figure 4.

In the case of Upper Lamp or Lower Lamp change
After changeing the Upper Lamp or Lower Lamp,
1. Select the Upper Lamp or Lower Lamp
2. Press the Menu key within an 5 seconds.
Then, Ch. No and time will be reset to zero (selected item only).
Figure 5, 6.
3-3
3-7 How to execute DDC
1. Open file.
2. Select Port #1.
3. Select DDC file.
4.Click, "Next" Button
5. Type in the monitor serial number and press Enter.

*Repeat this step 2 to 5 times in digital inputs after the analog input.
3-4
3-8 How to execute MCU Code

3-8-1 How to execute MCU Code
1. Set the options.

-. Manufacture: MSTAR
-. Device Type: TSUM16_ROM128K_ext_flash
-. Communication Port: DSUB15 (Analog)
-. External Memory: PMC25LV010E
2. Click 'LoadFile' button, and select the MCU code.
3-5
3. Click 'Auto Program' button.
4. If Program and Verify is OK, turn off the hard power and than turn on again.
3-6
3-9 How to execute HDCP Key
1. Execute 'service.exe'.
2. Click 'HDCP' button.
3-7
3. Click 'HDCP Write' button and select 'MStar_HDCPKEY'.
4. HDCP KEY writing is Complete.
3-8
7-1 Power Tree
7 Block Diagram
- Lamp (typ.) : 7.5 ~ 3.5 mArms
17" : 650Vrms, 19" : 720Vrms
I
P
normal : 720 mA
NTR2101OT1 dpms :
Panel Board
B normal : 720 mA
o dpms :
1.8V
5.0V normal : 300mA
a normal : 1,309 mA dpms : SE557MH - LF Core
dpms : AP1117-1.8
r normal : 545 mA AP1117-3.3 SE557MH - LF Interface
d dpms : 3.3V
normal : 245mA
dpms :
DPMS
0.6W
normal : 44 mA
7 Block Diagrams
Self-Loss
dpms :
SE557MH - LF internal micom
7-1
7 Block Diagrams
7-2 Main Board Part
SE16AW /
7-2
7 Block Diagrams
7-3 IP Board Part (SMPS Part)
7-3
7 Block Diagrams
7-4 IP Board Part (Inverter Part)
7-4
13 Circuit Descriptions
13-1 Overall Block Structure
13-1-1 Power Tree
- Lamp (typ.) : 7.5 ~ 3.5 mArms

17" : 650Vrms, 19" : 720Vrms
I
P
normal : 720 mA
NTR2101OT1 dpms :
Panel Board
B normal : 720 mA
o dpms :
1.8V
5.0V normal : 300mA
a normal : 1,309 mA dpms : SE557MH - LF Core
dpms : AP1117-1.8
r normal : 545 mA AP1117-3.3 SE557MH - LF Interface
d dpms : 3.3V
normal : 245mA
dpms :
DPMS
0.6W
normal : 44 mA
Self-Loss
dpms :
SE557MH - LF internal micom
1. When the AD board is in DPMS state:

1.1 The IP has been designed so that it operates with a power consumption of less than 0.6W of.
1.2 The Scaler consumes power up to 37mA
1.3 The power to the panel is switched off
2. When the AD board is operating normally:
2.1 The maximum power consumption of the panel lamps is described below (It may vary depending on
the panel manufacturer)
17" : 4*(7.5mA*650mVrms)=4*4.9=19.6W
19: : 4*(7.5mA*720mVrms)=4*5.4=21.6W
2.2 The power consumption of the Panel Control board is as follows: 5V*720mA=3.6W
2.3 The power consumption of the Scaler is as follows: 3.3V*245mA + 1.8V*300mA = 1.35W
13-1
13-1-2 Main Board Parts
1. Inverter: A conversion device that converts DC 6. Scaler & EEPROM: I2C is a two-way serial bus
rated voltage/current to high ones necessary of two lines that supports communications
for the panel lamp. across the integrated circuits as well as
between FLASH and EEPROM.
2. DC/DC(Regulator): General term for DC to DC In particular, MCU(SE557MH-LF) and use the
converting devices. SDR direct bus for mutual communications,
The IP board receives 5V and outputs 1.8 or which is an effective, speedy system because it
3.3V that is supplied to the scaler allows 4 additional address/data lines com-
(SE557MH-LF). pared to the old serial systems.
3. Power MosFET: The IP board receives 5V and 7. Function Key: A certain keystroke generates a
outputs a lower voltage in DPMS mode and certain electrical potential, which is transferred
supplies the whole 5V for the panel operating into ADC input port of the MCU and then con-
board in normal conditions. In that case, the verted to a digital value by the A/D converter of
switching of Power MosFET is controlled by the chip. The digital value (data) is a clue to
Micom. which key is entered. In practical, the voltage
levels are set as below.
4. Scaler: Receives the digital TMDS and analog
R,G,B signals and convert them to proper reso-
lutions using up- or down- scaling that are
transferred to the panel in the LDVS formats.
5. Crystal(Oscillator): Use one 14.318MHz

oscillator externally to supply power to both
MCU and Scaler at the same time.
13-2
13-1-3 IP BOARD BLOCK(POWER) Parts
13-1-4 IP BOARD BLOCK( INVERTER ) Parts
IP BO A RD
B LO C K ( IN V ERT ER )
IN V ERT ER PA RT
Lamp
D C Input
nput POWER FULL
+ 13V
1 dc DC INPUT BRIDGE Lamp
CIRCUIT Lamp
Lamp
FEED BACK
INVERTER
CIRCUIT
CONTROL
IC
+ 5V
5V ddc DRIVER
ON/OFF PROTECTION
A D IM + 3.
.3V
3 dc DIM INPUT IC CIRCUIT
BD IM + 4..5V dc
C O N T RO L PA RT
13-3
13-1-5 IP BOARD ( inverter ) PROTECTION Parts

BIZET INVERTER CONTROLER FAN7310 have 2-way of the PROTECTION MODE.
1. OVP[Over Voltage Protection] : If the Voltage of the series capacitors C10 & C15 is over the 2.0V, the
Inverter latched-off.[See the Picture1]
2. OLP[Over Load Protection] : If the inverter output harness is opened(No-output current), the base of the
Q1 turns on and chage the C9 ovter 2V and then, the Inverter latched-
off[See the Picture2]
Figure 1.
Figure 2.
13-4
13-2 Trouble Shooting

13-2-1 IP BOARD(Power)
Power On
No
Check fuse Change FUSE
Yes
3 pin of FDM0565R No
Vcc system in normal: HIGH Check the Vcc system
Yes
1 pin of FDM0565R No
Check the drain system Check the main switching
Normal: Switching
Yes
Check the No No Check the

Check the output current
protection system feedback system
Yes
Check others
Harness, Inlet
13-5
13-2-1 IP BOARD(Inverter)
Power On
No
Check the 13V line Check the power system
Yes
1 and 2 pins of FDM0565R No Check the IC drive

Check Protection Check MOSFET
Normal:0.6V~0.8V
Yes
1 and 2 pins of FDM0565R No

Check Protection Check the OVP and OLR
Normal:0.6V~0.8V circuits
Yes
Check any dimming No No Check the feedback

circuit Check the output current system
Yes
Check others
13-6
13-3 IP BOARD(Power) Schematic Diagrams
13-7
13-4 IP BOARD(Inverter) Schematic Diagrams
13-8
LCD-Monitor
Chassis Model
LS19HAK 940BW PLUS
SERVICE Manual
LCD Monitor Fashion Feature

-Wide Format Display (1440 x 900)
-Dynamic Contrast
-HDCP
-Integrated UI applied
-Connectivity : Analog (15p D-sub),
Digital (24p DVI-D)
-Power Consumption: 19" Wide(42W)
-DPMS: under 1 W (230Vac)
Copyright Trademarks
©2007 by Samsung Electronics Co., Ltd. Samsung is the registered trademark of Samsung
Electronics Co., Ltd.
All rights reserved.
This manual may not, in whole or in part, be copied, LS19HAK and MacMaster Cable Adapter are
photocopied, reproduced, translated, or converted to trademarks of Samsung Electronics Co., Ltd.
any electronic or machine readable form without prior
Macintosh, Power Macintosh are trademarks of Apple
written permission of Samsung Electronics Co., Ltd.
Computer, Inc.
LS19HAK Service Manual
All other trademarks are the property of their respective
First edition May 2007. owners.
Printed in Korea.
ii
Contents
1. Precautions ………………………………………………………………………………………………………………………………………1
1-1
1-1 Safety Precautions ……………………………………………………………………………………………………………………… 1-1
1-2 Servicing Precautions …………………………………………………………………………………………………………………… 1-2
1-3 Static Electricity Precautions …………………………………………………………………………………………………………… 1-2
1-4 Installation Precautions ………………………………………………………………………………………………………………… 1-3
2. Product specifications …………………………………………………………………………………………………………………………2

2-1
2-1 Fashion Feature…………………………………………………………………………………………………………………………… 2-1
2-2 Specifications ……………………………………………………………………………………………………………………………… 2-1
2-3 Spec Comparison ………………………………………………………………………………………………………………………… 2-2
2-4 Option Specification ……………………………………………………………………………………………………………………… 2-3
3. Alignments and Adjustments …………………………………………………………………………………………………………………3

3-1
3-1 Required Equipment …………………………………………………………………………………………………………………… 3-1
3-2 Automatic Color Adjustment …………………………………………………………………………………………………………… 3-1
3-3 DDC EDID Data Input …………………………………………………………………………………………………………………… 3-1
3-4 OSD Adjustment When Replacing Panel ……………………………………………………………………………………………… 3-1
3-5 OSD Adjustment When Replacing Lamp Only ………………………………………………………………………………………… 3-1
3-6 Service Function Spec. ………………………………………………………………………………………………………………… 3-2
3-7 How to execute DDC …………………………………………………………………………………………………………………… 3-4
3-8 How to execute MCU Code ………………………………………………………………………………………………………………3-5
3-9 How to execute HDCP Key ………………………………………………………………………………………………………………3-7
4. Troubleshooting 4-1
………………………………………………………………………………………………………………………………4
4-1 No Power …………………………………………………………………………………………………………………………………4-1
4-3 No Video (ANALOG) ……………………………………………………………………………………………………………………… 4-2
4-4 No Video (DIGITAL) ……………………………………………………………………………………………………………………… 4-4
5. Exploded View and Parts List 5-1

………………………………………………………………………………………………………………5
6. Electrical Parts List ……………………………………………………………………………………………………………………………6

6-1
7. Block Diagram …………………………………………………………………………………………………………………………………7

7-1
7-1 Power Tree ………………………………………………………………………………………………………………………………… 7-1
7-2 Main Board Part …………………………………………………………………………………………………………………………… 7-2
7-3 IP Board Part (SMPS Part) ……………………………………………………………………………………………………………… 7-3
7-4 IP Board Part (Inverter Part) …………………………………………………………………………………………………………… 7-4
8. Wiring Diagram …………………………………………………………………………………………………………………………………8

8-1
Contents
9. Schematic Diagrams ……………………………………………………………………………………………………………………………9

9-1
10. Operating Instructions and Installation ……………………………………………………………………………………………………1

10-1
10-1 Front …………………………………………………………………………………………………………………………………… 10-1
10-2 Rear……………………………………………………………………………………………………………………………………… 10-2
10-3 Connecting the monitor ……………………………………………………………………………………………………………… 10-3
10-4 Monitor Assembly ……………………………………………………………………………………………………………………… 10-5
10-5 Attaching a Base ……………………………………………………………………………………………………………………… 10-6
11. Disassembly and Reassembly ………………………………………………………………………………………………………………1

11-1
11-1 Disassembly (Simple - Stand) ……………………………………………………………………………………………………… 11-1
11-2 Disassembly (HAS-Stand) …………………………………………………………………………………………………………… 11-5
11-3 Reassembly …………………………………………………………………………………………………………………………… 11-8
12. PCB Diagram …………………………………………………………………………………………………………………………………1

12-1
13. Circuit Descriptions ……………………………………………………………………………………………………………………………1

13-1
13-1 Overall Block Structure ……………………………………………………………………………………………………………… 13-1
13-2 Trouble Shooting ……………………………………………………………………………………………………………………… 13-5
13-3 IP BOARD(Power) Schematic Diagrams …………………………………………………………………………………………… 13-7
13-4 IP BOARD(Inverter) Schematic Diagrams ………………………………………………………………………………………… 13-8
14. Reference Infomation…

…………………………………………………………………………………………………………………………14-1
14-1 Technical Terms ……………………………………………………………………………………………………………………… 14-1
14-2 Pin Assignments ……………………………………………………………………………………………………………………… 14-3
14-3 Timing Chart …………………………………………………………………………………………………………………………… 14-4
14-4 Preset Timing Modes ………………………………………………………………………………………………………………… 14-6
14-5 Panel Description ……………………………………………………………………………………………………………………… 14-7

Samsung Electronics Co.,Ltd.
-This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City,
Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742
Any unauthorized use of Manual can be punished Printed in Korea
under applicable International and/or domestic P/N : BN82-00171J-00
law. URL : http://itself.sec.samsung.co.kr/
11 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
11-1 Disassembly (Simple - Stand)

Cautions: 1. Disconnect the monitor from the power source before disassembly.
Description Picture Description
1. Place monitor face down on cushioned table.

Lift up the sub-cover.
2. Remove 3 screws from the stand.
3. Remove stand.
11-1

4. Remove front cover.
5. Lift up the back cover and Use the jig to remove

the shield lamp.
11-2
설명 진 설명
사Description Picture Description
6. Disconnect cables.
7. Lift up the shield and disconnect LVDS cable.
11-3
설명 사Description
진 설명 Picture Description
8. Remove 4 screws.
9. Remove 4 screws and Lift up the Main PCB and

IB Board.
10. Main PCB and IB Board.
11. LCD Panel.
11-4
11-2 Disassembly (HAS - Stand)
1. Place monitor face down on cushioned

table. Remove 2 screws from the stand
and remove front cover.
2. Lift up the back cover and Use the jig to remove

the shield lamp.
11-5
설명 진 설명
사Description Picture Description
3. Disconnect cables.
4. Lift up the shield and disconnect LVDS cable.
11-6
설명 사Description
진 설명 Picture Description
5. Remove 4 screws.
6. Remove 4 screws and Lift up the Main PCB and

IB Board.
7. Main PCB and IB Board.
8. LCD Panel.
11-7
11-2 Reassembly
Reassembly procedures are in the reverse order of disassembly procedures.
11-8
6 Electrical Parts List

You can search for updated part codes through ITSELF web site.
URL : http://itself.sec.samsung.co.kr/
6-1 LS19HAKCSQ/EDC Parts list
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
LS19HAKCSQ/EDC 940BW PLUS,WGA1/S19B4-LHA,19,LCD-MO,NETH

LS19HAKCSQ/EDC 940BW PLUS,WGA1/S19B4-LHA,19,LCD-MO,NETH
0.1 M0002 BN90-00906D ASSY COVER REAR;STZ-LS19HAWCSH/EDC 1 S.N.A

..2 M0013 BN96-03338D ASSY COVER P-REAR;LS19HAW,AM-LCD,HIPS,,B 1 S.A
...3 M0113 BN61-01581A BRACKET-VESA;BI17/19BS,SECC,T1.0 2 S.N.A
...3 M0952 BN63-02075A COVER-DUCT;HA17BS,HIPS,T1.5,13.5,13.5,HB 4 S.N.A
...3 M0006 BN63-02516B COVER-REAR;LS19HAW,HIPS,HB,HAS,BK24 1 S.N.A
0.1 M0216 BN90-00907A ASSY STAND;CTZ-LS19HAWKBQ/XAA 1 S.N.A

..2 M0003 BN96-05837A ASSY STAND P;-,LS19HAW (WIDE),-,HIPS HB, 1 S.A
...3 T0081 6001-001547 SCREW-MACHINE;BH,+,M4,L10(5),ZPC(BLK),SW 2 S.A
...3 M0081 6003-000275 SCREW-TAPTITE;BH,+,-,B,M3,L10,ZPC(BLK),S 5 S.N.A
...3 M0081 6003-000337 SCREW-TAPTITE;BH,+,S,M4,L10,ZPC(BLK),SWR 4 S.A
...3 M0081 6003-001001 SCREW-TAPTITE;FH,+,B,M3,L8,ZPC(BLK),SWRC 7 S.N.A
...3 HC+CW 6009-001370 SCREW-SPECIAL;PWH,+,-,M4,L8,ZPC(WHT),SWR 1 S.N.A
...3 BN61-00875A GUIDE-WASHER;HS15PO,SK-5,T0.5,NTR 4 S.N.A
...3 BN61-01396A HOLDER-SWIVEL RING;MJ17MS,ACETAL,NTR 1 S.N.A
...3 M0114 BN61-01397A HOLDER-WIRE;MJ17MS,ABS HB,BK07 1 S.N.A
...3 BN61-01404A BRACKET-STAND BOTTOM;MJ17MS,SECC,T2.0 1 S.N.A
...3 CIS4 BN61-01438A HOLDER-STAND;MATISSE HAS-STAND,SWRCH18A 1 S.N.A
...3 BN61-02073A BRACKET-STAND LIFT;HA17TS,SECC,T2.0,52.5 1 S.N.A
...3 BN61-02074A GUIDE-STAND BODY;HA17TS,ACETAL,T1.5,19.8 2 S.N.A
...3 BN61-02075A GUIDE-STAND LIFT;HA17TS,ACETAL,T2.0,57.6 1 S.N.A
...3 BN61-02433A BRACKET-STAND BODY;S/M 205BW,SECC,T2.0 1 S.N.A
...3 M0412 BN63-01515D COVER-SWIVEL BASE;MATISSE,HIPS,T2.5,200, 1 S.N.A
...3 M0174 BN63-01983B COVER-STAND TOP;HA17,HIPS,T2.5,200,200,H 1 S.N.A
...3 T0003 BN63-01984A COVER-STAND BOTTOM;HA17TS,HIPS,T2.5,200, 1 S.N.A
...3 BN63-02206A COVER-STAND SUB;HA17TS,HIPS,T2.0,80,100, 1 S.N.A
...3 BN63-02524B COVER-STAND REAR;LS20HAW(205BW),HIPS,HB, 1 S.N.A
...3 BN63-02525A COVER-STAND TILT;S/M 205BW,HIPS,HB,BK24 1 S.N.A
...3 BN63-02526A COVER-STAND FRONT;S/M 205BW,HIPS,HB,BK24 1 S.N.A
...3 T0132 BN73-00077A RUBBER FOOT;MATISSE,BUMPON,¨ª13.5,T2.0,6 4 S.N.A
...3 T0081 BN73-00085A RUBBER CUSHION;MATISSE,¨ª4.5(IN SIDE),CL 1 S.N.A
...3 M0007 BN96-01524A ASSY STAND P-STOPPER;-,MJ17BS,-,SUS T1.0 1 S.N.A
...3 M0126 BN96-02310A ASSY STAND P-SPRING;-,HA19TS,-,SUS301,-, 2 S.N.A
...3 T0054 BN96-05355A ASSY HINGE P;940B,HGI,SGCC,T2.0 1 S.A
....4 BN60-00040A SPACER-WASHER;940B,SK-5,8.0,14.0,0.4 4 S.N.A
....4 BN61-03141A BRACKET-HINGE TILT;940B,HGI, SGCC,T2.0 1 S.N.A
....4 T0530 BN61-03184A SPRING ETC-COIL;940B,SWPB,3.0,15.0,19.0, 1 S.N.A
....4 T0530 BN61-03185A SPRING ETC-COIL;940B,SWPB,3.0,15.0,19.0, 1 S.N.A
....4 BN61-03208A SPRING ETC-DISK;940B,SK-5,8.0,14.5,0.85 4 S.N.A
....4 BN61-03263A BRACKET-STAND VESA;940B,HGI, SGCC,T2.0 1 S.N.A
....4 BN66-00009A SHAFT-HINGE;940B,SUM24L,16.5,14 2 S.N.A
0.1 M0001 BN90-00988L ASSY COVER FRONT;LS19HAKCSQ,940BW PLUS 1 S.N.A

..2 T0003 BN96-03831K ASSY COVER P-FRONT;LS19HAK (940BWPLUS),, 1 S.A
...3 M0112 BN63-02723G COVER-FRONT;LS19HA(940BW PLUS),ABS,HB,SV 1 S.N.A
...3 T0022 BN64-00377B KNOB CONTROL;HA17TS,PC CLEAR,T2.1,9,112, 1 S.N.A
...3 M0145 BN96-02474C ASSY BOARD P-FUNCTION;HAYDN,YWP-VD-05-05 1 S.A
....4 M0014 BN94-01300K ASSY PCB MAIN-SEDA,FUCHION PCB;HAYDN* 1 S.N.A
.....5 CIS 0203-001809 TAPE-DOUBLE FACE;467MP,-,-,W7.80,L106.67 1 S.N.A
.....5 SW1 BN34-00001A SWITCH-DOME SHEET;HYADN_FUNCTION F/K,DOM 1 S.A
6-1

.....5 M2893 BN39-00688A LEAD CONNECTOR;HAYDN,UL1571#30,4P,450mm, 1 S.A
.....5 CIS BN61-01846A GUIDE-CONTROL;HA17T,ABS HB,T1.1,9,112,IV 1 S.N.A
.....5 T0174 BN97-01589K ASSY SMD;HAYDN* 1 S.N.A
......6 L0405 0601-001896 LED;SMD,BLUE,1.6x0.8x0.4mm,470,1.6x0.8x0 1 S.A
......6 R110 2007-000081 R-CHIP;2.7Kohm,5%,1/10W,TP,1608 1 S.A
......6 CN330 3711-005935 HEADER-BOARD TO CABLE;BOX,4P,1R,1mm,SMD- 1 S.A
......6 T0077 BN41-00633A PCB MAIN;HAYDN,FR4,2L,MP1.0,0.6T,105*8,1 1 S.N.A
0.1 M0112 BN91-01030C ASSY SHIELD;LS19HAWKBH/XAA,AM LCD 1 S.N.A

..2 BN63-02523A SHIELD-LAMP;LS19HAW,SPTE,T0.3 1 S.N.A
0.1 M0017 BN91-01681Q ASSY CHASSIS-STZ,W/W;LS19HAKCSQ/EDC 1 S.A

..2 M0081 6003-000115 SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(BLK),SWRC 3 S.A
..2 M0081 6003-001439 SCREW-TAPTITE;BH,+,-,S,M4,L8,ZPC(WHT),SW 1 S.N.A
..2 M0174 BN44-00124K IP BOARD;IP-35155A(SW),MENDEL,3.0 ~5.0mA 1 S.A
..2 M0014 BN94-01387P ASSY PCB MAIN-STZ,W/W;LS19HAKCSQ/EDC* 1 S.N.A
...3 T0245 0202-001492 SOLDER-WIRE FLUX;HSE-02 LFM48 SR-34 S,-, 0.003 S.N.A
...3 CN102 3701-001173 CONNECTOR-DVI;24P,3R,FEMALE,ANGLE,AUF 1 S.A
...3 CN101 3701-001219 CONNECTOR-DSUB;15P,3R,FEMALE,ANGLE,AUF 1 S.A
...3 HDCP KEY BN97-00707A ASSY HDCP;BN46-00018A,BR20/21BS_CS,MSTAR 1 S.N.A
....4 BN46-00018A KEY CODE-CERTIFICATE;(HDCP KEY)PPM42M5S, 1 S.N.A
...3 T0174 BN97-01710F ASSY SMD;LS19HAKCSQ/EDC 1 S.N.A
....4 SUB05 0202-001477 SOLDER-CREAM;LST309-M,-,D20~45§-,96.5Sn/ 0.615 S.N.A
....4 D100 0401-001056 DIODE-SWITCHING;MMBD4148SE,100V,200mA,SO 1 S.A
....4 D600 0402-001614 DIODE-RECTIFIER;S1G,400V,1A,DO-214AC,TP 1 S.A
....4 D603 0402-001614 DIODE-RECTIFIER;S1G,400V,1A,DO-214AC,TP 1 S.A
....4 ZD100 0403-001411 DIODE-ZENER;-,5.49-5.73V,200mW,SOD-323,T 1 S.A
....4 D0254 0404-001020 DIODE-SCHOTTKY;BAT54C,30V,200mA,SOT-23,T 1 S.A
....4 ZD200 0406-001061 DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S 1 S.A
....4 ZD201 0406-001061 DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S 1 S.A
....4 Q201 0501-000445 TR-SMALL SIGNAL;KTC3875S-Y,NPN,150mW,SOT 1 S.A
....4 Q103 0501-002080 TR-SMALL SIGNAL;2SC2412K,NPN,200mW,SC-59 1 S.A
6-2

....4 Q409 0505-001165 FET-SILICON;SI3443BDV,P,-20V,+-4.4A,65mo 1 S.A
....4 IC112 1103-000129 IC-EEPROM;24C02,2Kbit,256x8Bit,SOP,8P,5x 1 S.A
....4 IC112 1103-001023 IC-EEPROM;24C08,8Kbit,1Kx8Bit,SOP,8P,5x4 1 S.A
....4 IC603 1202-000164 IC-VOLTAGE COMP.;393,SOP,8P,150MIL,DUAL, 1 S.A
....4 T0087 1203-003695 IC-POSI.FIXED REG.;NCP1117ST33T3G,SOT-22 1 S.A
....4 T0087 1203-003696 IC-POSI.FIXED REG.;NCP1117DT18T5G,DPAK,3 1 S.A
....4 R110 2007-000043 R-CHIP;1Kohm,1%,1/10W,TP,1608 1 S.A
....4 R110 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000071 R-CHIP;22ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000082 R-CHIP;3.3Kohm,5%,1/10W,TP,1608 1 S.A
6-3

....4 R110 2007-000309 R-CHIP;10ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000309 R-CHIP;10ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-000821 R-CHIP;390ohm,1%,1/10W,TP,1608 1 S.A
....4 R110 2007-000821 R-CHIP;390ohm,1%,1/10W,TP,1608 1 S.A
....4 R110 2007-001002 R-CHIP;510ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-001044 R-CHIP;56ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-001044 R-CHIP;56ohm,5%,1/10W,TP,1608 1 S.A
....4 R110 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608 1 S.A
....4 R110 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608 1 S.A
....4 R110 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608 1 S.A
....4 C120 2203-000236 C-CER,CHIP;0.1nF,5%,50V,C0G,1608 1 S.A
....4 C120 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,1608 1 S.A
6-4

....4 C120 2203-005065 C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608 1 S.A
....4 C231 2402-001128 C-AL,SMD;100¥ìF,20%,16V,-,TP,6.3X5.7mm 1 S.A
....4 X201 2801-003667 CRYSTAL-SMD;14.31818MHz,30ppm,28-AAN,16p 1 S.A
....4 T0568 3301-001407 BEAD-SMD;30ohm,1608,300mA,TP,,,0.4ohm 1 S.N.A
....4 T0568 3301-001407 BEAD-SMD;30ohm,1608,300mA,TP,,,0.4ohm 1 S.N.A
....4 T0568 3301-001569 BEAD-SMD;600ohm,2012,1000mA,TP,520ohm/90 1 S.N.A
6-5

....4 CN400 3708-001150 CONNECTOR-FPC/FFC/PIC;30P,1mm,SMD-A,SN,Y 1 S.A
....4 CN330 3711-005503 HEADER-BOARD TO CABLE;BOX,9P,1R,2mm,SMD- 1 S.A
....4 CN330 3711-005509 HEADER-BOARD TO CABLE;BOX,4P,1R,1.25mm,S 1 S.A
....4 T0077 BN41-00897A PCB MAIN;LS19HAK,Silver through,2,MP1.0, 1 S.N.A
....4 MICOM BN97-01695U ASSY MICOM-STZ,W/W;M-HA19K0CAA-1000,(600 1 S.N.A
.....5 IC115 1107-001614 IC-FLASH MEMORY;MX25L1005,1Mbit,1Mx1Bit, 1 S.N.A
....4 IC109 1205-003292 IC-LCD CONTROLLER;SE557MH-LF,PQFP,128P,2 1 S.A
..2 M0251 BN96-02854J ASSY CABLE P;-,UL21341,FFC CABLE,120MM,1 1 S.A
..2 M0006 BN96-03340C ASSY SHIELD P-COVER;940BW,SECC T1.0,AMLC 1 S.N.A
...3 BN61-01578A BRACKET-SHIELD;BI19BS,SECC,T1.0 1 S.N.A
...3 M0001 BN63-01774A SHIELD-INSULATOR;BI17/19BS,PET,T0.35 1 S.N.A
...3 M0107 BN63-02522C SHIELD-COVER;940BW,SECC,T1.0,AMLCD 1 S.N.A
..2 M2893 BN39-00785A LEAD CONNECTOR;LS19PLMTSQ,UL1007#26,UL/C 1 S.A
0.1 BN91-01803E ASSY LCD-STH;LS19HAK* 1 S.N.A

..2 M0215 BN07-00351B LCD-PANEL;LTM190M2-L31,Haydn,6bit Hi-FRC 1 S.A
0.1 M0019 BN92-00329V ASSY LABEL;NB21BSAS/CLT,CHILE 1 S.N.A
0.1 M0113 BN92-01619W ASSY P/MATERIAL;LS19HAWCSQ/EDC 1 S.N.A

..2 T0376 6902-000061 BAG AIR;LDPE,T0.2,L1000,W500,TRP,,, 0.007 S.N.A
..2 T0376 6902-000379 BAG AIR;LDPE,T0.2,W1000,L1800,TRP,-,-- 0.002 S.N.A
..2 T0003 6902-000604 BAG WRAPPING;LDPE,T0.02,W500,L10000,TRP, 0.608 S.N.A
..2 M0081 6902-000609 BAG ROLL;LDPE,T0.05,W2400,L1000,TRP,-,- 0.1 S.N.A
..2 T0524 6902-000241 BAG PE;NITRON/HDPE,T0.5/T0.012,W600,L600 1 S.N.A
0.1 M0045 BN92-02820X ASSY ACCESSORY;LS19HAKCSQ/EDC 1 S.N.A

..2 M0114 BN39-00244B CBF SIGNAL;MO15PS,15P/15P,20276-N,1830mm 1 S.A
..2 M0125 BN39-00246F CBF SIGNAL-DVI(D);1703FP,24P/24P,20276-D 1 S.A
..2 M0045 BN96-05725W ASSY ACCESSORY;LS19HAKCSQ/EDC,-,-,-,-,- 1 S.A
...3 T0268 3903-000042 CBF-POWER CORD;DT,EU,FP3/YES,IEC320 C13/ 1 S.A
...3 T0524 6902-000110 BAG PE;LDPE,T0.05,W250,L400,TRP,28,2 1 S.N.A
...3 ACCESSORY BH68-70448A CARD-01;TFT LCD,SRC,RUSSIA,S/W,120,W210* 1 S.N.A
...3 ACCESSORY BN68-00907A MANUAL FLYER-01,CARD;COMM,SAMSUNG,18 LAN 1 S.N.A
...3 ACCESSORY BN68-01118B MANUAL-01,TCO03 CARD;COMM,W/W,Mojo 100g, 1 S.N.A
...3 ACCESSORY BN68-01237A MANUAL FLYER-QSG;COMM,W/W(L12),Mojo 100g 1 S.N.A
...3 M0215 BN96-03059Y ASSY MANUAL P-IB+QSG;940BWPlus,-,-,-,W/W 1 S.N.A
....4 QSG BH68-00376L MANUAL FLYER-06,QSG;LCDQUICK SETUP GUIDE 1 S.N.A
....4 IB BN59-00509Y S/W DRIVER-00,IB;940BWPlus,W/W,SyncMaste 1 S.N.A
...3 ACCESSORY BH68-00633B MANUAL FLYER-00,WARRANTY CARD;comm,Samsu 1 S.N.A
0.1 M0003 BN92-02823C ASSY BOX;LS19HAKCSQ/EDC 1 S.N.A

..2 M0045 BN69-01995A BOX-MONITOR;LS19HAK(S/M940BW PLUS),CB,SY 1.02 S.N.A
..2 T0081 BN96-02895A ASSY MISC P-HANDLE PACKING;ALL MODEL,BN6 1 S.N.A
...3 M0103 BN66-00007A LEVER-TOP;ALL MODEL,LDPE,WHITE 1 S.N.A
...3 M0102 BN66-00008A LEVER-BOTTOM;ALL MODEL,LDPE,WHITE 1 S.N.A
6-6
5 Exploded View & Parts List
5 Exploded View and Parts List

-You can search for updated part codes through ITSELF web site.
URL : http://itself. sec. samsung.co.kr
5-1 LS19HAKCSQ/EDC Exploded View
M0215
5-1
5 Exploded View & Parts List
- Parts list
Location Code.No Item & Specification Q'ty SA/SNA Remark
M0215 BN07-00351B LCD-PANEL;LTM190M2-L31,Haydn,6bit Hi-FRC 1 S.A
5-2
10 Operating Instructions and Installation

10-1 Front
1. Menu button 2) Text : Normal brightness

Opens the OSD menu. Also use to exit the OSD For documentations or works involving heavy text.
menu or return to the previous menu.
3) Internet : Medium brightness
2. MagicBright button For working with a mixture of images such as text
MagicBright is a new feature providing optimum and graphics.
viewing environment depending on the contents of
the image you are watching. Currently six different 4) Game
modes are available: Custom, Text, Internet, For watching motion pictures such as a game.
Game, Sport and Movie. Each mode has its own
pre-configured brightness value. You can easily 5) Sport
select one of six settings by simply pressing For watching motion pictures such as a sport.
MagicBright control buttons.
6) Movie : High brightness
1) Custom For watching motion pictures such as a DVD or
Although the values are carefully chosen by our Video CD.
engineers, the pre-configured values may not be
comfortable to your eyes depending on your taste. 7) Dynamic Contrast
If this is the case, adjust the brightness and con- Dynamic Contrast is to automatically detect distri-
trast by using the OSD menu. bution of inputted visual signal and adjust to create
optimum contrast.
10-1
3. Brightness button 5. Auto button

When OSD is not on the screen, push the button Use this button for auto adjustment.
to adjust brightness.
6. Power button / Power indicator
2,3. Adjust buttons Use this button for turn the monitor on and off.
Adjust items in the menu. /This light glows green during nomal operation,
and blinks green once as the monitor saves your
4. Enter button / Source button adjustments..
Activates a highlighted menu item. /
Push the 'SOURCE', then selects the video signal
while the OSD is off. (When the source button is
pressed to change the input mode, a message
appears in the center of the screen displaying the
current mode -- analog or digital input signal.)
Note : If you select the digital mode, you must con-
nect your monitor to the graphic card's port using
the DVI cable.
10-2 Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
Connect the power cord for your monitor to the power port on the back of the monitor.
2. DVI port
Connect the DVI cable to the DVI port on the back of your monitor.
3. D-sub 15-pin port

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
4. Power on/off Switch(option)

Use this button for turn the monitor on and off.
5. Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a public place.
(The locking device has to be purchased separately. )
To get the information on using the Kensington Lock, contact an aurhorized dealer.
10-2
10-3 Connecting the monitor
Rear of monitor New Model Macintosh

Rear of Computer
Old Model Macintosh
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub(Analog) connector on the video card.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
2-2. Using the DVI(Digital PC, Digital DVD ) connector on the video card.
Connect the DVI cable to the DVI port on the back of your monitor.
2-3. Connected to a Macintosh.

Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adapter.
3. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
10-3
10-3-1 Connecting Digital DVD
¡Ø The monitor has DVI IN connection terminals to connect DVI input devices digital DVD.
1. Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the
DVI cable.
2. Then, start the DVD with a DVD disc inserted.
3. Select Digital using the SOURCE button .
10-4
10-4 Monitor Assembly
10-5
10-5 Attaching a Base

- This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad.
A. Monitor
B. Mounting interface pad
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four
screws that came with the arm-type base, wall mount hanger or other base.
10-6
12 PCB Layout
12 PCB Diagram
12-1
12 PCB Layout
Memo
12-2
1 Precautions
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.
1-1 Safety Precautions
1-1-1 Warnings
1. For continued safety, do not attempt to modify the circuit
board.
2. Disconnect the AC power and DC power jack before
servicing.
1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor, Disconnect the AC
line cord from the AC outlet.
2. It is essential that service technicians have an accurate
voltage meter available at all times. Check the
calibration of this meter periodically.
1-1-3 Fire and Shock Hazard

Before returning the monitor to the user, perform the Figure 1-1. Leakage Current Test Circuit
following safety checks:
1. Inspect each lead dress to make certain that the leads are 4. With the unit completely reassembled, plug the AC line
not pinched or that hardware is not lodged between the cord directly into a 120V AC outlet. With the unit’s AC
chassis and other metal parts in the monitor. switch first in the ON position and then OFF, measure
2. Inspect all protective devices such as nonmetallic control the current between a known earth ground (metal water
knobs, insulating materials, cabinet backs, adjustment pipe, conduit, etc.) and all exposed metal parts,
and compartment covers or shields, isolation resistor- including: metal cabinets, screwheads and control shafts.
capacitor networks, mechanical insulators, etc. The current measured should not exceed 0.5 milliamp.
3. Leakage Current Hot Check (Figure 1-1): Reverse the power-plug prongs in the AC outlet and
repeat the test.
WARNING : Do not use an isolation
transformer during this test.
Use a leakage current tester or a metering system that 1-1-4 Product Safety Notices
complies with American National Standards Institute Some electrical and mechanical parts have special safety-
(ANSI C101.1, Leakage Current for Appliances), and related characteristics which are often not evident from visual
Underwriters Laboratories (UL Publication UL1410, inspection. The protection they give may not be obtained by
59.7). replacing them with components rated for higher voltage,
wattage, etc. Parts that have special safety characteristics are
identified by on schematics and parts lists. A substitute
replacement that does not have the same safety characteristics
as the recommended replacement part might create shock, fire
and/or other hazards. Product safety is under review
continuously and new instructions are issued whenever
appropriate.
1-1
1 Precautions
1-2 Servicing Precautions

WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section
of this manual.
Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety
precautions, always follow the safety precautions.
1-2-1 General Servicing

Precautions 4. Check the insulation between the blades of the AC plug
1. Always unplug the unit’s AC power cord from the AC and accessible conductive parts (examples: metal panels,
power source and disconnect the DC Power Jack before input terminals and earphone jacks).
attempting to: 5. Insulation Checking Procedure: Disconnect the power
(a) remove or reinstall any component or assembly, (b) cord from the AC source and turn the power switch ON.
disconnect PCB plugs or connectors, (c) connect a test Connect an insulation resistance meter (500 V) to the
component in parallel with an electrolytic capacitor. blades of the AC plug.
2. Some components are raised above the printed circuit The insulation resistance between each blade of the AC
board for safety. An insulation tube or tape is sometimes plug and accessible conductive parts (see above) should
used. The internal wiring is sometimes clamped to be greater than 1 megohm.
prevent contact with thermally hot components. Reinstall 6. Always connect a test instrument’s ground lead to the
all such elements to their original position. instrument chassis ground before connecting the positive
3. After servicing, always check that the screws, lead; always remove the instrument’s ground lead last.
components and wiring have been correctly reinstalled.
Make sure that the area around the serviced part has not
been damaged.
1-3 Static Electricity Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called
Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The
following techniques will reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor 6. Do not remove a replacement ESD from its protective
components or assemblies, drain the electrostatic charge package until you are ready to install it. Most
from your body by touching a known earth ground. replacement ESDs are packaged with leads that are
Alternatively, wear a discharging wrist-strap device. To electrically shorted together by conductive foam,
avoid a shock hazard, be sure to remove the wrist strap aluminum foil or other conductive materials.
before applying power to the monitor. 7. Immediately before removing the protective material
2. After removing an ESD-equipped assembly, place it on a from the leads of a replacement ESD, touch the
conductive surface such as aluminum foil to prevent protective material to the chassis or circuit assembly into
accumulation of an electrostatic charge. which the device will be installed.
3. Do not use freon-propelled chemicals. These can Caution: Be sure no power is applied to the
generate electrical charges sufficient to damage ESDs. chassis or circuit and observe all
4. Use only a grounded-tip soldering iron to solder or other safety precautions.
desolder ESDs.
5. Use only an anti-static solder removal device. Some 8. Minimize body motions when handling unpackaged
solder removal devices not classified as “anti-static” can replacement ESDs. Motions such as brushing clothes
generate electrical charges sufficient to damage ESDs. together, or lifting your foot from a carpeted floor can
generate enough static electricity to damage an ESD.
1-2
1 Precautions
1-4 Installation Precautions

1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage
required for carrying the product. cables and install it firmly. Contact with the high-
voltage cable or the antenna falling over may
2. Keep the power cord away from any heat emitting cause fire or electric shock.
devices, as a melted covering may cause fire or
electric shock. 7. When installing the product, leave enough space
(10cm) between the product and the wall for
3. Do not place the product in areas with poor ventilation purposes.
ventilation such as a bookshelf or closet. The A rise in temperature within the product may
increased internal temperature may cause fire. cause fire.
4. Bend the external antenna cable when connecting

it to the product. This is a measure to protect it
from being exposed to moisture. Otherwise, it
may cause a fire or electric shock.
5. Make sure to turn the power off and unplug the

power cord from the outlet before repositioning
the product. Also check the antenna cable or the
external connectors if they are fully unplugged.
Damage to the cord may cause fire or electric
shock.
1-3
1 Precautions
Memo
1-4
2 Product Specifications
2-1 Fashion Feature

- Wide Format Display (1440 x 900)
- HAS/SIMPLE Stand
- Silver/Black Color Variation
- Dynamic Contrast
- HDCP
2-2 Specifications
Item Description
LCD Panel TFT-LCD panel, RGB vertical stripe, normally white transmissive,
19-Inch wide viewable, 0.2835 (H) x 0.2835 (V) mm pixel pitch
Scanning Frequency Horizontal : 30 kHz ~ 81 kHz (Automatic)

Vertical : 56 Hz ~ 75 Hz
Display Colors 16.7 Million colors
Maximum Resolution Horizontal : 1440 Pixels

Vertical : 900 Pixels
Input Video Signal Analog, Digital

Input Sync Signal Type : Seperate H/V sync, Composite H/V, Sync-on-Green
Level : TTL level
Maximum Pixel Clock rate 135 MHz
Active Display
Horizontal/Vertical 408.24 mm / 255.15 mm
AC power voltage & Frequency AC 100 ~ 240 Volts, 60/50 Hz ± 3 Hz

Power Consumption 42W (Max)
Dimensions Simple-Stand HAS-Stand

Set (W x D x H) 439.0 x 200.0 x 360.7mm(17.3 x 7.8 x 14.2 inch) 439.0 x 200.0 x 327.3mm(17.3x 7.8 x 12.8 inch)
Weight (Set) 4.2 kg 5.6 kg
Environmental Considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating Humidity : 10 % ~ 80 %
Storage Temperature : - 4°F ~ 113°F (-20°C ~ 45°C)
Storage Humidity : 5 % ~ 95 %
- Designs and specifications are subject to change without prior notice.
2-1
2-3 Spec Comparison
LS19HAW LS19HAK
Model
940BW 940BW PLUS
Design
Screen Size 19" Wide 19" Wide
Resolution 1440x900@60Hz 1440x900@60Hz
Colors 16.2M 16.2M
Brightness 300cd/m2 300cd/m2
800:1
Contrast 700:1
Dynamic Contrast Typ. 2000:1
Response Time 2ms(G to G) 5ms(W to B)
Frequency
Horizontal / 30~81kHz / 56~75Hz 30~81kHz / 56~75Hz
Vertical
Input Sync Signal Separate, Composite, Sync-on-Green Separate, Composite, Sync-on-Green
Power
42 Watt (Max) 42 Watt (Max)
Consumption
DPMS < 1W < 1W
Magic Bright Text / Internet / Sport / Text / Internet / Sport /Movie / Game /
Movie / Game / Custom Custom / Dynamic Contrast
2-2
2-4 Option Specification
Item Item Name CODE.NO Remark
Quick Setup Guide BH68-00376L
Warranty Card
(Not available in all loca- BH68-00633A
tions)
User's Guide,
Monitor Driver,
Natural Color software, BN59-00509Y
TM
MagicTune software
D-Sub(15 Pin)
BN39-00244B
Cable
Power Cord 3903-000042
DVI Cable BN39-00246F Sold separatelys
2-3
Memo
2-4
14 Reference Infomation
14-1 Technical Terms
-TFT-LCD -FINE
(Thin film Transistor Liquid Crystal Display) "Fine" adjustment is used to adjust visibility by con-
ADC(Analog to Digital Converter) trol phase difference.
This is a circuit that converts from analog signal to
digital signals. -COARSE
This is a adjustment by tuning with Video colck and
-PLL(Phase Locked Loop) PLL clock.
During progressing ADC, Device makes clock syn-
chronizing HSYNC with Video clock -DVI (Digital Visual Interface)
This provides a high speed digital connection for
-Inverter visual data types that is display technology inde-
Device that supply Power to LCD panel lamp. this pendent. this interface is primarily forcused at pro-
device gernerate about 1,500~2,000V. viding a connection between a computer and
its display device.
AC Adapter
Device that converts AC(90V~240V) to DC(+12V or -L.V.D.S.(Low Voltage Differential Signaling)
14V) a kind of transmission method for Digital.It can be
used from Main PBA to Panel.
-SMPS(Switching Mode Power Supply)
Switching Mode Power supply. This design technol- -T.M.D.S
ogy is used to step up/down the input power by (Transition minimized Differential Signaling)
switching on/off a kind of transmission method for Digital.
It can be used from Video card to Main PBA.
-FRC(Frame Rate Controller)
Technology that change image frame quantity dis- -DDC(Display data channel)
played on screen for one second. It is a communication method between Host
Actually TFT-LCD panel require 60 pcs of frame for Computer and related equipment.
one second. It can make it Plug and Play between PC and
so,this technology is needed to convert input image Monitor.
to 60 pcs regardless input frame quantity.
-EDID
-Image Scaler Extended Display Identification Data PC can recog-
Technology that convert various input resolution to nize the monitor information as Product data,
other resolution.(ex. 640* 480 to 1024*768) Product name,Display mode,Serial number and
Signal source,etc through DDC Line communicating
-Auto Configuration(Auto adjustment) with PC and Monitor.
This is an algorithm to adjust monitor to optimum
-Dot Pitch
condition by pushing one key. The image on a monitor is composed of red, green
and blue dots. The closer the dots, the higher the
-OSD(On Screen Display) resolution. The distance between two dots of the
same color is called the 'Dot Pitch'. Unit: mm
On screen display. customer can control the screen
easily with this.
14-1
-Vertical Frequency
The screen must be redrawn several times per sec-
ond in order to create and display an image for the
user. The frequency of this repetition per second is
called Vertical Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times
per second, this is regarded as 60 Hz.
-Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the
Horizontal Cycle is called Horizontal Frequency.
Unit: kHz
-Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the
top to the bottom in order is called the Non-Interlace
method while showing odd lines and then even lines
in turn is called the Interlace method. The Non-
Interlace method is used for the majority of monitors
to ensure a clear image. The Interlace method is the
same as that used in TVs.
-Plug & Play

This is a function that provides the best quality
screen for the user by allowing the computer and
the monitor to exchange information automatically.
This monitor follows the international standard
VESA DDC for the Plug & Play function.
-Resolution
The number of horizontal and vertical dots used to
compose the screen image is called 'resolution'.
This number shows the accuracy of the display.
High resolution is good for performing multiple tasks
as more image information can be shown on the
screen.
Example: If the resolution is 1280 x 1024 , this

means the screen is composed of 1280 horizontal
dots (horizontal resolution) and 1024 vertical lines
(vertical resolution).
14-2
14-2 Pin Assignments
Sync 15-Pin D-Sub Signal Cable Connector

Type
Pin No. Separate Composite Sync-on-green
1 Red Red Red
2 Green Green Green + H/V Sync.
3 Blue Blue Blue
4 GND GND GND
5 DDC Return (GND) DDC Return (GND) DDC Return (GND)
6 GND-R GND-R GND-R
7 GND-G GND-G GND-G
8 GND-B GND-B GND-B
9 DDC Power Input (+5V) DDC Power Input (+5V) DDC Power Input (+5V)
10 Self Raster Self Raster Self Raster
11 GND GND GND
12 Bi-Dr Data (SDA) Bi-Dr Data (SDA) Bi-Dr Data (SDA)
13 H-Sync. H/V-Sync. Not Used
14 V-Sync. Not Used Not Used
15 DDC Clock (SCL) DDC Clock (SCL) DDC Clock (SCL)
Sync
Type 24P DVI-D
Pin No.
1 Rx2- 13 No Connection
2 Rx2+ 14 +5V_M
3 GND 15 Self Raster
4 No Connection 16 +5V_M
5 No Connection 17 Rx0-
6 DDC Clock (SCL) 18 Rx0+
7 DDC Data (SDA) 19 NC
8 NC 20 No Connection
9 Rx1- 21 No Connection
10 Rx1+ 22 NC
11 NC 23 RxC+
12 No Connection 24 RxC-
14-3
14-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard for computer-
generated video signals.
Table 1. Timing Chart
Mode IBM VESA
VGA2/ VGA3/
640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 1280/60 Hz 1280/75 Hz
70 Hz 60 Hz
640x480 800x600 800x600 1024x768 1024x768 1280x1024 1280x1024
Timing 720 x 400 640 x 480
fH (kHz) 31.469 31.469 37.500 37.879 46.875 48.363 60.023 63.981 79.975
A μsec 31.777 31.778 26.667 26.400 21.333 20.677 16.660 11.852 12.504
B μsec 3.813 3.813 2.032 3.200 1.616 2.092 1.219 1.037 1.067
C μsec 1.589 1.589 3.810 2.200 3.232 2.462 2.235 2.296 1.837
D μsec 26.058 26.058 20.317 20.000 16.162 15.754 13.003 9.259 9.481
E μsec 0.318 0.318 0.508 0.000 0.323 0.369 0.203 0.000 0.119
fV (Hz) 70.087 59.940 75.000 60.317 75.000 60.004 75.029 60.020 75.025
O msec 14.268 16.683 13.333 16.579 13.333 16.666 13.328 16.005 13.329
P msec 0.064 0.064 0.080 0.106 0.064 0.124 0.050 0.047 0.038
Q msec 0.858 0.794 0.427 0.607 0.448 0.600 0.466 0.594 0.475
R msec 13.155 15.761 12.800 15.840 12.800 15.880 12.795 15.630 12.804
S msec 0.191 0.064 0.027 0.0261 0.021 0.062 0.017 0.016 0.013
Clock
Freq. 28.322 26.175 31.500 40.000 49.500 75.000 78.750 108.000 135.000
(MHz)
Polarity
H.Sync Negative Negative Negative Positive Positive Negative Positive Positive Positive
V.Sync Positive Negative Negative Positive Positive Negative Positive Positive Positive
Remark Separate Separate Separate Separate Separate Separate Separate Separate Separate
14-4
Table 2. Timing Chart
Mode IBM
1440/60 Hz 1440/75 Hz
Timing 1440x900 1440x900
fH (kHz) 55.935 70.635

A μsec 17.878 14.157
B μsec 1.427 1.112
C μsec 2.178 1.814
D μsec 13.521 10.530
E μsec 0.751 0.702
fV (Hz) 59.887 74.984
O msec 16.698 13.336
P msec 0.107 0.085
Q msec 0.447 0.467
R msec 16.090 12.741
S msec 0.054 0.042
Clock
Freq. 106.500 136.750
(MHz)
Polarity
H.Sync Negative Negative
V.Sync Positive Positive
Remark Separate Separate
Separate Sync H/V Composite Sync
Video Video
C D E Q R S
Sync-on-Green
Sync Sync
B P
A O
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch
14-5
14-4 Preset Timing Modes
-If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen
will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED
is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing
Horizontal
Vertical Frequency Pixel Clock Sync Polarity
Display Mode Frequency
(Hz) (MHz) (H/V)
(kHz)
IBM, 640 x 350 31.469 70.086 25.175 +/-
IBM, 640 x 480 31.469 59.940 25.175 -/-
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 -/-
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 x 1024 60.000 60.000 108.000 +/+
VESA, 1280 x 1024 79.976 75.025 135.000 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA, 1440 x 900 70.635 74.984 136.750 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an
image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
14-6
14-5 Panel Description
Maker VENDOR P/N PANEL_CODE PANEL_ABB STICKER_CODE Remarks
SEC LT140X1-002 BN07-00004A SA BN68-00239H -

SEC LT150XS-L01 BN07-00009A SB -
SEC LT150XS-L01-B BN07-00022A SC -
SEC LTM150XS-L02 BN07-00005A SD -
SEC LT181E2-132 BN07-00001A SE -
SEC LT150XS-T01 BN07-00010A SF -
SEC LTM181E3-132 BN07-00019A SG -
SEC LT170E2-131 BN07-10001D SH -
SEC LT181E2-131 BN07-10001E SJ -
SEC LTM170E4-L01 BN07-00018A SK -
SEC LTM240W1-L01 BN07-00015A SL -
SEC LTM213U3-L01 BN07-00016A SM -
SEC LTM150XH-L01 BN07-00026A SN -
SEC LTM150XH-L03 BN07-00027A SP -
SEC LTM150XS-L01 BN07-00032A SQ DELL(ZPD)
SEC LTM181E4-L01 BN07-00034A SR PVA
SEC LTM170EH-L01 BN07-00036A SS TN
SEC LTM170E5-L01 BN07-00037A SU PVA
SEC LTM150XH-L11 BN07-00041A SV -
SEC LTM213U4-L01 BN07-00039A SW PVA
SEC LTM150XH-L01(ZPD) BN07-00045A SX ZPD
SEC LTM150XH-L04 BN07-00046A SY New panel with high brightness
SEC LTM170W1-L01 BN07-00047A SZ Panel for TV
SEC LTM150XH-L06 BN07-00053A EA Panel for TV/ High luminance for 450cd _ SONY&EOS Team Panel for TV
SEC LTM153W1-L01 BN07-00054A EB Use NIKE MODEL
SEC LTM170EH-L05 BN07-00055A EC Panel EOS proj. for high brightness of 17" EH-L05
SEC LTM170E5-L03 BN07-00056A ED Dell 1702FP pro. E4. EH mechanical Compatible
SEC LTM190E1-L01 BN07-00057A EE DELL 1900 FP
SEC LTM181E5-L01 BN07-00061A EF 18" narrow bezel GH18PS
SEC LTM150XP-L01 BN07-00065A EG AMLCD PVA PANEL
SEC LTM240W1-L02 BN07-00062A EH Panel for 15" Wide TV
SEC LTM170EU-L01 BN07-00071A EJ Slim design, TN
SEC LTM170E5-L04 BN07-00072A EK E5-L04 6 bits FRC... for IBM
SEC LTA220W1-L01 BN07-00074A EL Panel for 22" TV
SEC LTM170E6-L02 BN07-00075A EM AMLCD Narrow & slim design 17" PVA mode
SEC LTM170W1-L01 BN07-00082A EN LTM170W1-L01 ZPD panel
SEC LTM170EH-L01 BN07-00080A EP LTM170EH-L01 ZPD panel
SEC LTM170E5-L01 BN07-00081A EQ LTM170E5-L01 ZPD panel
SEC LTM170EH-L05 BN07-00083A ER LTM170EH-L05 ZPD panel
SEC LTM170E5-L03 BN07-00084A ES LTM170E5-L03 ZPD panel
SEC LTM170EU-L01 BN07-00085A ET LTM170EU-L01 ZPD panel
SEC LTM170E5-L04 BN07-00086A EU LTM170E5-L04 ZPD panel
SEC LTM170E6-L02 BN07-00087A EV LTM170E6-L02 ZPD panel
SEC LTM150XH-L06 BN07-00091A EW Color coordinates change for LCD TV
SEC LTM153W1-L01 BN07-00092A EX AMLCD WIDE 15",9/10
SEC LTM170W1-L01 BN07-00100A EY Color Coordinates change code management
SEC LTM170EH-L05 BN07-00097A EZ LTM170E5-L05 Color Coordinates Change Panel Code
SEC LTA400W1-L01 BN07-00109A S1 PANEL of AMLCD 40" TV
SEC LTM153W1-L01 BN07-00110A S2 Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC LTM150XH-L06 BN07-00111A S3 Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC LTM170W1-L01 BN07-00112A S4 Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC LTM170EH-L05 BN07-00113A S5 Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC LTM220W1-L01 BN07-00114A S6 ZPD Panel for AMLCD 22" TV
SEC LTM150XH-L06 BN07-00117A S7 ZPD Panel code
SEC LTM153W1-L01 BN07-00118A S8 ZPD Panel code
14-7
SEC LTM170WP-L01 BN07-00119A S9 PVA Panel for NIKE

SEC LTM213U4-L01 BN07-00039A E1 21.3" NARROW
SEC LTA260W1-L01 BN07-00121A E2 VENUS
SEC LTA220W1-L01 BN07-00074B E3 Panel B-level panel code for 22" TV Panel
SEC LTA320W1-L01 BN07-00108A E4 Panel for AMLCD 32" TV
SEC LTM213U4-L01 BN07-00124A E5 NARROW BEZEL 21 " PANEL
SEC LTM170E6-L04 BN07-00129A E6 HIGHLAND 17" LOW PANEL (Panel only for TCO03)
SEC LTM190E1-L01 BN07-00088A E7 LTM190E1-L01 ZPD panel
SEC M150X4-L06 BN07-00137A E8 15" Narrow & Slim panel
SEC LTA170V1 BN07-00139A E9 17" Panel for Muse 4:3 VGA TV
SEC LTM190E1-L02 BN07-00128A E10 New Panel from AMLCDl, Specification : 6bit Driver IC
SEC LTM170EX-L01 BN07-00143A E11 Development new Panel from AMLCD
SEC LTM170E8-L01 BN07-00144A E12 Development new Panel from AMLCD
SEC LTM170E6-L04 BN07-00129B E13 ZPD panel for AMLCD (Panel only for TCO03)
SEC LTA320W1-L02 BN07-00108B E14 Creat B-level Panel code for AMLCD 32" TV
SEC LTM190E1-L03 BN07-00151A E15 Development new 19" Panel form AMLCD (Panel only for TCO03)
SEC LTM240W1-L03 BN07-00134A E16 AMLCD 24" panel development
SEC LTM190E1-L02 BN07-00128B E17 New Panel from AMLCD, Specification : 6bit Driver IC(ZPD)
SEC LTM190E4-L01 BN07-00145A E18 AMLCD 24" new panel development
SEC LTM170E8-L01 BN07-00158A E19 ZPD code derivation
SEC LTM170EX-L01 BN07-00159A E20 ZPD code derivation
SEC LTM190E1-L03 BN07-00151B E21 Creat new panel code for AMLCD 19" (Panel only for TCO03)
SEC LTA460H1-L01 BN07-00157A E22 creat panel code for AMLCD 46" TV
SEC LTM170EU-L11 BN07-00160A E23 creat new panel code for AMLCD 17" (Panel only for TCO03)
SEC LTM240W1-L03 BN07-00134B E24 24" panel ZPD code derivation
SEC LTM190E4-L01 BN07-00145B E25 AMLCD 19" ZPD Panel code derivation
SEC LTM240W1-L03 BN07-00134B E26 24" panel ZPD code derivation
SEC LTM150XO-L01 BN07-00164A E27 AMLCD 15" XO-L01 new panel development
SEC LTM150XO-L01 BN07-00164B E28 AMLCD 15" XO-L01 ZPD code derivation
SEC LTM170EU-L11 BN07-00160B E29 AMLCD 17" NEW panel code derivation
SEC LTA320W2-L01 BN07-00172A SPZ AMLCD 32" NEW panel
SEC LTM213U4-L01 BN07-00124B SPZ 21.3" Narrow PANEL ZPD Panel derivation
SEC LTM170EU-L11 BN07-00189A STH AMLCD EU-L11 Pb free panel code derivation
SEC LTM170EU-L11 BN07-00189B STZ AMLCD EU-L11 Pb free panel ZPD code derivation
SEC LTM240W1-L04 BN07-00188A SPH 24" A-DCC new panel development
SEC LTM240W1-L04 BN07-00188B SPZ 24" A-DCC panel ZPD code derivation
SEC LTM190EX-L01 BN07-00191A STH AMLCD 19" TN new Panel
SEC LTM190EX-L02 BN07-00191B STZ AMLCD 19" TN new Panel ZPD derivation
SEC LTA230W1-L02 BN07-00184A SPZ AMLCD 23" 16:9 new Panel
SEC LTM240M1-L01 BN07-00195A SPH 24" panel with high brightness deveiopment
SEC LTM150XO-L01 BN07-00197A STH AMLCD 15" XO-L01 Pb free panel code
SEC LTM150XO-L01 BN07-00197B STZ AMLCD 15" XO-L01 Pb free panel ZPD code
SEC LTM170EU-L21 BN07-00202A STZ AMLCD EU-L21 ZPD new code derivation
SEC LTA460W2-L03 BN07-00187A SPZ BEETOVEN 46"ZPD new panel
SEC LTM240M1-L01 BN07-00195B SPZ 24" igh brightness panel ZPD code derivation
SEC M170EX-L21 BN07-00206A STZ AMLCD LTM170EX-L21 ZPD new code derivation
SEC LTA460H3-L01 BN07-00200A SPZ AMLCD 46" LED BLU panel
SEC LTM170EU-L15 BN07-00214A STZ AMLCD EU-L15 TV high brightness ZPD new code derivation
SEC LTM170E8-L21 BN07-00218A SPZ AMLCD LTM170E8-L21 PVA ZPD new code derivation
SEC LTM190EX-L21 BN07-00222A STZ DISPLAY LCD
SEC LTM201U1-L01 BN07-00190B SPZ AMLCD 20.1" Normal panel ZPD code derivation
SEC LTM190E4-L21 BN07-00223A SPZ HAYDN 17" PZD code PANEL derivation
SEC LTA570H1-L01 BN07-00196A SPZ AMLCD 57" new panel development
14-8
SEC LTM150XO-L21 BN07-00229A STZ AMLCD 15" XO-L21 8ms panel code
SEC LTA260W2-L11 BN07-00239A SPZ AMLCD 26" 16:9 7Line new Panel
SEC LTA400WS-LH1 BN07-00245A SPZ AMLCD 40" 16:9 SPVA 90% new Panel
SEC LTM213U6-L01 BN07-00231A SPZ AMLCD 21.3" PVA new Panel Code
SEC LTM213U6-L01 BN07-00231B SPH AMLCD 21.3" PVA Panel HPD Code
SEC LTM190M2-L01 BN07-00227A STZ AMLCD 19" TN Wide new Panel Code development
SEC LTM201UX-L01 BN07-00249A STZ AMLCD 20.1" TN new Panel Code development
SEC LTM240M1-L02-A05 BN07-00250A SPZ 24" High luminance Slim panel ZPD code
SEC LTA320W3-L02 BN07-00219A SPZ AMLCD 32" new Panel
SEC LTA320W2-L11 BN07-00259A SPZ AMLCD 32" 16:9 IP Board Panel
SEC LTA460WS-L02 BN07-00252A SPZ AMLCD 46" 16:9 SPVA 72% Panel
SEC LTA400WT-L01 BN07-00264A SPZ
SEC LTM240M2-L02 BN07-00267A SPZ LCD Monitor 24" wide SPVA ZPD new code
SEC LTM210M2-L02 BN07-00230A SPZ
SEC LTA320WT-L11 BN07-00257A SPZ
SEC LTM190EX-L21-G BN07-00274A STZ AMLCD 19" TN Glare new Panel Code
SEC LTA320WT-L14 BN07-00247A SPZ -
SEC LTM190M2-L01-D016 BN07-00280A STZ AMLCD 19" TN Wide change Gamma Panel Code
SEC LTM190EX-L31 BN07-00279A STZ AMLCD 19" TN new Panel Code
SEC LTM190M2-L02 BN07-00287A STZ AMLCD 19" TN Wide high brightness new Panel Code
SEC LTA400WS-L01 BN07-00246A SPZ Display-LCD (Div) 07AH
SEC LTA460WS-L01 BN07-00311A SPZ -
SEC LTM190E4-L31 BN07-00316A SPZ -
CPT CLAA150XG09 BN07-00141A PA CPT 15" Monitor new panel development
CPT CLAA170EA02 BN07-00148A PB 17" CPT NEW development panel
CPT CLAA170EA02 BN07-00148B PC 17" CPT ZPD panel code derivation
CPT CLAA150XG09 BN07-00141B PTZ CPT 15" panel ZPD code derivation (GOYA-PJT)
CPT CLAA150XP01 BN07-00173A PTH CPT 15" PSWG code derivation
CPT CLAA150XP01 BN07-00173B PTZ CPT 15" PSWG panel ZPD code
CPT CLAA170EA07 BN07-00174A PTH CPT 17" PSWG panel code derivation
CPT CLAA170EA07 BN07-00174B PTZ CPT 17" PSWG type new Panel code
CPT CLAA170EA07Q BN07-00220A PTZ CPT 17" PSWG R/T 8msec code derivation
CPT CLAA170EA07Q BN07-00220B PTH CPT 17" PSWG R/T 8msec HPD code derivation
CPT CLAA150XP01F BN07-00236A PTZ CPT 15" PSWG panel ZPD & Lead free code derivation
CPT CLAA201WA03Q BN07-00269A PTZ CPT 20.1" wide TN ZPD new code development
CPT CLAA320WA01 BN07-00276A PMZ CPT 32" 16:9 MVA 8bit 60Hz / Panel brown
CPT CLAA170ES01 BN07-00261A PTZ CPT 17" Slim TN ZPD Type new code development
CPT CLAA070VA02 BN07-00265A PTZ electonic Album new Panel code development
TOSHIBA LTM15C419(A) BN07-00002A TA -
TOSHIBA LTM15C423(B) BN07-00006A TB -
TOSHIBA LTM18C161 BN07-00008A TC -
TOSHIBA LTM15C443 BN07-00031A TD -
TOSHIBA LTM15C458 BN07-00043A TE -
TOSHIBA LTM15C458S BN07-00077A TF TSB 15" high brightness Panel
TOSHIBA LTM15C458 BN07-00078A TG Toshiba ZPD panel
TOSHIBA LTM15C458S BN07-00099A TH TSB LTM15C458S ( ZPD )
HANNSTAR HSD150MX41A(A) BN07-00020A NA TTL type
HANNSTAR HSD150MX12 BN07-00030A NB TTL type
HANNSTAR HSD170ME13 BN07-00180A NTH Hannstar 17" TN new panel development
HANNSTAR HSD170ME13 BN07-00180B NTZ Hannstar 17" TN new panel development ZPD code derivation
HANNSTAR HSD190ME12 BN07-00210A NTZ Hannstar 19" TN new panel development
HANNSTAR HSD150MX17-A BN07-00226A NTZ Hannstar 15" slim panel ZPD code derivation
HANNSTAR HSD190ME12-A10 BN07-00256A NTZ Hannstar 19" TN PSWG 8ms new panel development
14-9
HANNSTAR HSD190ME13-D11 BN07-00270A NTZ Hannstar 19" TN Slim 5ms new panel development
TORISAN TM150XG-22L03(A) BN07-00021A RA -
TORISAN TM150XG-26L06 BN07-00042A RB -
TORISAN TM181SX-76N01 BN07-00048A RC -
TORISAN TM150XG-26L06 BN07-00059A RD 15" XGA TN MODE(ZPD)
TORISAN TM290WX-71N31 BN07-00063A RE RS24NS (TORISAN 29" NEW PANEL)
TORISAN TM396WX-71N31 BN07-00064A RF RS24NS (TORISAN 40" NEW PANEL)
TORISAN TM150XG-26L09 BN07-00073A RG Panel for 15" TV
TORISAN TM150XG-26L10 BN07-00089A RH L10(change except D/IC) ZPD
TORISAN TM150XG-26L10 BN07-00090A RJ L10 NORMAL
TORISAN TM190SX-70N01 BN07-00098A RK Torisan 19" Panel
TORISAN TM181SX-76N01 BN07-00106A RL ZPD Panel code
TORISAN TM190SX-70N01 BN07-00107A RM ZPD Panel code
TORISAN TM290WX-71N31 BN07-00115A RN Color Coordinates change panel for TORISAN 29" TV
TORISAN TM396WX-71N31 BN07-00116A RP,Q Color Coordinates change panel for TORISAN 40" TV
TORISAN TM22OWX-71N31 BN07-00125A RR Development TORISAN 22" TV PANEL (ZPD)
TORISAN TM22OWX-71N31 BN07-00127A RS Development TORISAN 22" TV PANEL (HPD)
TORISAN TM396WX-71N32A BN07-00150A RT 120V inverter Exclusive panel
TORISAN TM190SX-70N02 BN07-00154A RMH Torisan 6bit panel code Derivation
TORISAN TM190SX-70N02 BN07-00154B RMZ Torisan 6bit panel code Derivation
TORISAN TM150XG-A01 BN07-00162A RTH Torisan 15" Narrow & Slim panel development
TORISAN TM150XG-A01 BN07-00162B RTZ Torisan 15" N&S panel ZPD code Derivation
SHARP LQ181E1DG11(A) BN07-10001C PA -
SHARP LQ150X1LW71 BN07-00067A PB SHARP 15" PVA PANEL
SHARP LQ370T3LZ41 BN07-00216A FAZ Rome2
HITACHI TX38D12VC0CAA(A) BN07-00003A HA -
HITACHI TX43DVCOCAB BN07-00060A HB 17" SXGA PVA MODE
HITACHI TX43D15VC0CAB BN07-00101A HC ZPD Panel
HITACHI TX51D11VC0CAB BN07-00122A HD 20.1" NARROW
HITACHI TX54D11VC0CAB BN07-00123A HE 21.3" NARROW
HITACHI TX80D12VC0CAB BN07-00169A HIZ Development new panel for Hitachi 32" TV (ZPD)
HITACHI TX54D11VC0CAB BN07-00123B HIZ Hitachi 21.3"ZPD panel
IBM ITSX94S BN07-00017A IA -
UNIPAC UM170E0 BN07-00028A UA Loaded by cisdba
HYUNDAI HT15X13 BN07-00035A DA -
HYUNDAI HT17E11-200 BN07-00049A DB TN MODE
HYUNDAI HT17E11-300 BN07-00093A DC HT17E11-300 ZPD panel
HYUNDAI HT17E11-400 BN07-00094A DD HT17E11-400 normal panel
HYUNDAI HT17E11-400 BN07-00095A DE HT17E11-400 ZPD panel code
HYUNDAI HT17E12 BN07-00096A DF HT17E12 (Narow & slim Design )
HYUNDAI HT17E12 BN07-00105A DG ZPD Panel code
HYUNDAI HT15X15-D00 BN07-00146A DH Development for Ares 15" Hydis TV
HYUNDAI HT15X15-D01 BN07-00146B DJ Derivation panel HPD for Ares 15" Hydis TV
HYUNDAI HT17E13-100 BN07-00167A DTH PINEHURST-2(IBM) PJT 17" HYDIS PANEL Derivation
HYUNDAI HT17E13-100 BN07-00167B DTZ PINEHURST-2(IBM) Hydis 17" ZPD code Derivation
HYUNDAI HT170EX1-100 BN07-00240A DTZ 17" EX compatible Hydis Slim panel development
HYUNDAI HT201V01-100 BN07-00263A DTZ Hydis 20.1" 4:3 VGA Mode TN Panel
HYUNDAI HT170EX1-101 BN07-00266A DTZ 17" EX compatible Hydis Slim panel multichannel IC new code derivation
ACER L170E3 BN07-00044A AA TN(ADT)
ACER M170EN05 BN07-00076A AB AU 17" Panel ( Narrow & slim design )
ACER M170EN05 BN07-00102A AC ZPD Panel code
ACER M190EN02 BN07-00170A AMH AU Monitor 19" new panel development (P19-1S)
ACER M190EN02 BN07-00170B AMZ AU 19" ZPD code derivation (ZPD)
ACER M170EN06 BN07-00171A ATH AU Monitor 17" New panel development
ACER T260XW01 BN07-00163A AMZ AU 26" new panel development (NF26EO)
14-10
ACER A201SN01 BN07-00177A ATZ AU TV panel 20.1" TN SVGA new panel development
ACER M170EN06 BN07-00171B ATZ AU Monitor 17" ZPD code derivation
ACER T315XW01 BN07-00194A AMZ AU 32" new
ACER M170EG01 BN07-00192A ATH AU TN PSWG type new Panel code
ACER M170EG01 BN07-00192B ATZ AU TN PSWG type NEW panel code derivation
ACER M190EN04 BN07-00203A ATH AU Monitor 19" ZPD new Panel code
ACER T260XW02 BN07-00208A AMZ AUO 26" ZPD panel
ACER M170EG01 V8 BN07-00221A ATZ AU TN PSWG type new Panel (8msec) ZPD code derivation
ACER T260XW02 BN07-00233A AMZ AUO 26" Panel new (Cosmetic spec down grade)
ACER T315XW01 BN07-00234A AMZ AUO 32" Grade new (Cosmetic spec down grade)
ACER M190EN03 BN07-00224A AMZ AU Monitor 19" MVA new code derivation
ACER T315XW01 BN07-00237A AMZ LCD TV VE project new
ACER T315XW01 BN07-00238A AMZ LCD TV VE project new
ACER M201UN02 V3 BN07-00168A AMZ
ACER M201UN02 V3 BN07-00168B AMH
ACER M190EN04 V7 BN07-00248A ATZ AU Monitor 19" TN Glare ZPD new code derivation
ACER A070VW01 BN07-00235A ATZ electonic Album new Panel code
ACER T315XW01 BN07-00253A AMZ LCD TV VE item model : T315XW01
ACER T260XW02 BN07-00254A AMZ AUO 26" VE item model
ACER M170EU01 BN07-00260A ATZ AUO 17" Slim TN ZPD Type new code derivation
ACER T370XW01 BN07-00255A AMZ ROME 37" model
CHIMEI M170E3-LO1 BN07-00050A CA TN PANEL
CHIMEI M150X3-L01 BN07-00051A CB COMPATIBLE
CHIMEI M170E4-L01 BN07-00052A CC MVA PANEL
CHIMEI M150X2-L01 BN07-00066A CD CHIME 15"I PVA PANEL
CHIMEI M150X3-L01 BN07-00079A CE Chimei ZPD panel
CHIMEI M170E3-L01 BN07-00103A CF ZPD Panel code
CHIMEI M170E4-L01 BN07-00104A CG ZPD Panel code
CHIMEI V296W1-L01 BN07-00120A CH MVA
CHIMEI M170E6-L02 BN07-00126A CJ HIGHLAND 17" LOW PANEL
CHIMEI M190E2-L01 BN07-00131A CK GH19AS,BS CHIMEI PANEL
CHIMEI M150X4-L06 BN07-00137A CL 15" Narrow & Slim panel
CHIMEI M170E6-L01 BN07-00133A CM 2003-03-11 vendor change
CHIMEI M170E6-L01 BN07-00133B CN ZPD derivation panel
CHIMEI V201V1-T01 BN07-00135A CP CHIMEI 20.1" panel development
CHIMEI M170E6-L02 BN07-00126B CQ HIGHLAND 17" LOW PANEL ZPD derivation panel
CHIMEI M170E6-L05 BN07-00152A CR CMO 17" new panel development code
CHIMEI M170E6-L05 BN07-00152B CS CMO 17" ZPD panel code derivation
CHIMEI M150X4-L06 BN07-00137B CT Chimei 15" Narrow & Slim panel ZPD derivation
CHIMEI M170E5-L05 BN07-00165A CTH CMO 17" new panel development code (GOYA2-PJT)
CHIMEI M170E5-L05 BN07-00165B CTZ CMO 17" ZPD panel(GOYA2-PJT)
CHIMEI V230W1-L02 BN07-00209A CMZ CMO 23" development
CHIMEI V320B1-L01 BN07-00207A CMZ CMO 32" development
CHIMEI V270W1-L01 BN07-00136A CMZ CHI MEI 27" panel development
CHIMEI M190E5-L0A BN07-00213A CTZ
CHIMEI M190E3-L0A BN07-00212A CMZ CMO M190E3-L0A MVA Type new code
CHIMEI M170E7-L01 BN07-00232A CTZ CMO 17" Slim TN ZPD Type new code
CHIMEI M190A1-L01 BN07-00228A CTZ CMO 19" Wide TN ZPD Type new code
CHIMEI V201V1-T03 BN07-00275A CTZ CMO 20.1" (V201V1-T01) VE model
CHIMEI M201P1-L01 BN07-00268A CTZ CMO 20.1" TN ZPD derivation
NEC SVA150XG04TB BN07-00225A BTZ SVA NEC 15" panel ZPD code
NEC SVA170SX01TB BN07-00272A BTZ SVA NEC 17" panel ZPD code brown
14-11
9 Schematic Diagrams
- This Document can not be used without Samsung s authorization.
9-1 Schematic Diagrams
Reset Option
R247->0ohm
IC204 delete
1 GND 3
IN OUT
GND
C
R134
XREF 1KohmB
HOTPLUG
E
Q103
2SC2412K-Q
MGND1
MGND2
1 OUT 3 3 2
IN OUT VIN VOUT
GND ADJ
9-1
1 2 3 4
5 6
9-2
4 Troubleshooting
4 Troubleshooting
Notes: 1. Before troubleshooting, setup the PC's display as below.

- Resolution: 1440 x 900
- H-frequency: 56 kHz
- V-frequency: 60 Hz
2. If no picture appears, make sure the power cord is correctly connected.
3. Check the following circuits.
- No raster appears: Function PBA, Main PBA, I/P PBA
- 5V develop but no screen: Main PBA
- 5V does not develop: I/P PBA
4. If you push and hold the " (Enter/Source)" button for more than 5 seconds, the monitor
automatically returns to the factory preset.
4-1 No Power
Check Function Ass'y.

Yes
When Pin 4 of CN600 is 0V,

does proper DC 5V No
Change IP Board.
appear at Pin 7 and 9 of
CN600 separately?
Yes
When Pin 1 of IC601 is DC 5V No

does proper DC3.3V appear at Check IC601 and rerated circuit.
Pin 3 of IC603?
Yes
When Pin 3 of IC602 is DC 5V No

does proper DC1.8V appear at Check IC602 and related circuit.
Pin 2 of IC602?
4-1
4 Troubleshooting
4-3 No Video (ANALOG)
Check signal cable connection and

power.
No
1 X201 oscillate proprely? Replace or check related circuit.
Yes
Is there R,G,B input at No

Check input part.
R111,R114 and R118?
Yes
Is there Hsync, Vsync waveform No

2 3 Check IC200 and related circuit.
at Pin 37,38 of IC200?
Yes
Does the output signal appear No

Check CN400 and related circuit.
at Pin 8 ~ 30 of CN400?
Yes
No Check PANEL_EN SIGNAL at R223

There are DC 5V at Pin 1,
is High(On:High) and BL_EN signal
2 and 3 of CN400?
at R601(ON:Low) is Low
Yes
Replace LCD Panel.
4-2
4 Troubleshooting
WAVEFORMS
1 2
4-3
4 Troubleshooting
4-4 No Video (DIGITAL)
Check signal cable connection and

power.
No
1 X201 oscillate properly? Replace or check related circuit.
Yes
Is there R, G, B input at
4 5 6 No
Check input part.
R100,R101,R102,R106
and R108?
Yes
Does the output signal appear No

Check IC400 and related circuit.
at Pin 8 ~ 30 of CN400?
Yes
There are DC 5V at Pin 1, No Check the PANEL_EN signal at R223

2 and 3 of CN400? and BL_EN signal at R601.
Yes
Replace LCD Panel.
4-4
4 Troubleshooting
WAVEFORMS
1 4
5 6
4-5
4 Troubleshooting
Memo
4-6
8 Wiring Diagram 8 Wiring Diagram
8 Wiring Diagram
8-1 Wiring Diagram
8-1
8 Wiring Diagram
Memo
8-2

Samsung 940bw Plus

Uploaded by

Copyright:

Available Formats

Samsung 940bw Plus

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Samsung 940bw Plus

Uploaded by

Copyright:

Available Formats

3 Alignments and Adjustments

3 Alignments and Adjustments

3-1 Required Equipment

3-2 Automatic Color Adjustment

3-3 DDC EDID Data Input

3-5 OSD Adjustment When Replacing Lamp Only

3-6 Service Function Spec.

Figure 2. The example of service function OSD

The service function OSD is based on a grid of 29 columns x 12 rows.

3-6-2 How to Control Service Function OSD

3-6-3 How to Control Service Function OSD

3-6-4 How to Control Service Function OSD

3-7 How to execute DDC

5. Type in the monitor serial number and press Enter.

3-8 How to execute MCU Code

1. Set the options.

2. Click 'LoadFile' button, and select the MCU code.

3. Click 'Auto Program' button.

3-9 How to execute HDCP Key

2. Click 'HDCP' button.

3. Click 'HDCP Write' button and select 'MStar_HDCPKEY'.

4. HDCP KEY writing is Complete.

- Lamp (typ.) : 7.5 ~ 3.5 mArms

1. When the AD board is in DPMS state:

13-1-2 Main Board Parts

5. Crystal(Oscillator): Use one 14.318MHz

13-1-3 IP BOARD BLOCK(POWER) Parts

13-1-4 IP BOARD BLOCK( INVERTER ) Parts

13-1-5 IP BOARD ( inverter ) PROTECTION Parts

13-2 Trouble Shooting

Check the No No Check the

1 and 2 pins of FDM0565R No Check the IC drive

1 and 2 pins of FDM0565R No

Check any dimming No No Check the feedback

13-3 IP BOARD(Power) Schematic Diagrams

13-4 IP BOARD(Inverter) Schematic Diagrams

LCD Monitor Fashion Feature

1-1 Safety Precautions ……………………………………………………………………………………………………………………… 1-1

1-2 Servicing Precautions …………………………………………………………………………………………………………………… 1-2

1-3 Static Electricity Precautions …………………………………………………………………………………………………………… 1-2

1-4 Installation Precautions ………………………………………………………………………………………………………………… 1-3

2. Product specifications …………………………………………………………………………………………………………………………2

2-1 Fashion Feature…………………………………………………………………………………………………………………………… 2-1

2-2 Specifications ……………………………………………………………………………………………………………………………… 2-1

2-3 Spec Comparison ………………………………………………………………………………………………………………………… 2-2

2-4 Option Specification ……………………………………………………………………………………………………………………… 2-3

3. Alignments and Adjustments …………………………………………………………………………………………………………………3

3-1 Required Equipment …………………………………………………………………………………………………………………… 3-1

3-2 Automatic Color Adjustment …………………………………………………………………………………………………………… 3-1

3-3 DDC EDID Data Input …………………………………………………………………………………………………………………… 3-1

3-4 OSD Adjustment When Replacing Panel ……………………………………………………………………………………………… 3-1

3-5 OSD Adjustment When Replacing Lamp Only ………………………………………………………………………………………… 3-1

3-6 Service Function Spec. ………………………………………………………………………………………………………………… 3-2

3-7 How to execute DDC …………………………………………………………………………………………………………………… 3-4

3-8 How to execute MCU Code ………………………………………………………………………………………………………………3-5

3-9 How to execute HDCP Key ………………………………………………………………………………………………………………3-7

4-1 No Power …………………………………………………………………………………………………………………………………4-1

4-3 No Video (ANALOG) ……………………………………………………………………………………………………………………… 4-2

4-4 No Video (DIGITAL) ……………………………………………………………………………………………………………………… 4-4