FM 3080 Hind: Fixed Mount Barcode Scanner

SCANNING MADE SIMPLE
FM3080 Hind
fixed mount barcode scanner
user guide
Disclaimer
© 2018 Fujian Newland Auto-ID Tech. Co., Ltd. All rights reserved.
Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you
should keep this manual for future reference.
Do not disassemble the device or remove the seal label from the device, doing so will void the product warranty provided by Fujian
Newland Auto-ID Tech. Co., Ltd.
All pictures in this manual are for reference only and actual product may differ. Regarding to the product modification and update,
Fujian Newland Auto-ID Tech. Co., Ltd. reserves the right to make changes to any software or hardware to improve reliability,
function, or design at any time without notice. The information contained herein is subject to change without prior notice.
The products depicted in this manual may include software copyrighted by Fujian Newland Auto-ID Tech. Co., Ltd or third party.
The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode,
reverse engineer, rent, transfer or sublicense such software without prior written consent from the copyright holders.
This manual is copyrighted. No part of this publication may be reproduced, distributed or used in any form without written
permission from Newland.
Fujian Newland Auto-ID Tech. Co., Ltd. reserves the right to make final interpretation of the statement above.
Fujian Newland Auto-ID Tech. Co., Ltd.

3F, Building A, No.1, Rujiang West Rd., Mawei, Fuzhou, Fujian, China 350015
http://www.newlandaidc.com
Revision History
Version Description Date
V1.0.0 Initial release. December 18, 2018

Table of Contents
Revision History .......................................................................................................................................................................- 3 -
Preface .......................................................................................................................................................................................... 1
Introduction ...................................................................................................................................................................... 1
Chapter Description ......................................................................................................................................................... 1
Explanation of Icons ......................................................................................................................................................... 2
Chapter 1 Getting Started ............................................................................................................................................................ 3
Introduction ...................................................................................................................................................................... 3
Features of the FM30 ....................................................................................................................................................... 3
Unpacking ........................................................................................................................................................................ 3
FM30 Scanner.................................................................................................................................................................. 4
Data Port Pinout ............................................................................................................................................................... 5
Connecting the Scanner to a Host Device ....................................................................................................................... 6
Using USB Cable ...................................................................................................................................................... 7
Using RS-232 Cable ................................................................................................................................................. 8
Dimensions (unit: mm) ..................................................................................................................................................... 9
Field of View (unit: mm).................................................................................................................................................. 10
Power On, Power Off, Reboot ........................................................................................................................................ 11
Scanning Instructions ..................................................................................................................................................... 11
Maintenance................................................................................................................................................................... 11
Chapter 2 EasySet ...................................................................................................................................................................... 12
Chapter 3 System Settings ........................................................................................................................................................ 13
Introduction .................................................................................................................................................................... 13
Barcode Programming ............................................................................................................................................ 13
Command Programming ......................................................................................................................................... 13
EasySet Programming ............................................................................................................................................ 13
Programming Barcode/ Programming Command/Function ............................................................................................ 14
Use of Programming Command ..................................................................................................................................... 15
Command Syntax ................................................................................................................................................... 15
Query Commands ................................................................................................................................................... 15
Responses .............................................................................................................................................................. 16
Examples ................................................................................................................................................................ 16
Use of Programming Barcodes ...................................................................................................................................... 17
Illumination ..................................................................................................................................................................... 18
Illumination LED Selection ...................................................................................................................................... 19
Good Read LED ............................................................................................................................................................. 19
Good Read LED Duration ....................................................................................................................................... 20
Good Read LED Selection ...................................................................................................................................... 21
Power On Beep .............................................................................................................................................................. 22
Good Read Beep ........................................................................................................................................................... 22
Good Read Beep Duration ...................................................................................................................................... 23
Good Read Beep Frequency .................................................................................................................................. 24
Good Read Beep Volume ....................................................................................................................................... 25
Scan Mode ..................................................................................................................................................................... 26
Decode Session Timeout ............................................................................................................................................... 27
Image Stabilization Timeout (Sense Mode) .................................................................................................................... 28
Reread Timeout.............................................................................................................................................................. 29
Image Decoding Timeout ............................................................................................................................................... 30
Trigger Selection (Sense Mode) ..................................................................................................................................... 31
Image Change Trigger Sensitivity ........................................................................................................................... 32
IR Proximity Trigger Sensitivity ............................................................................................................................... 33
Trigger Commands......................................................................................................................................................... 34
Modify Start Scanning Command ........................................................................................................................... 34
Modify Stop Scanning Command ............................................................................................................................ 35
Make a Beeping Sound .................................................................................................................................................. 35
Scanning Preference...................................................................................................................................................... 36
Read Barcode On/Off ..................................................................................................................................................... 36
Decode Area .................................................................................................................................................................. 37
Image Flipping................................................................................................................................................................ 39
Bad Read Message........................................................................................................................................................ 40
Set Bad Read Message .......................................................................................................................................... 40
Default Settings .............................................................................................................................................................. 41
Factory Defaults ...................................................................................................................................................... 41
Custom Defaults ..................................................................................................................................................... 41
Query Product Information ............................................................................................................................................. 42
Query Product Name .............................................................................................................................................. 42
Query Firmware Version ......................................................................................................................................... 42
Query Decoder Version ........................................................................................................................................... 43
Query Hardware Version ......................................................................................................................................... 43
Query Product Serial Number ................................................................................................................................. 43
Query Manufacturing Date ...................................................................................................................................... 44
Query OEM Serial Number ..................................................................................................................................... 44
Query Data Formatter Version ................................................................................................................................ 44
Chapter 4 RS-232 Interface ........................................................................................................................................................ 45
Introduction .................................................................................................................................................................... 45
Baud Rate ...................................................................................................................................................................... 46
Parity Check ................................................................................................................................................................... 47
Data Bit .......................................................................................................................................................................... 48
Stop Bit .......................................................................................................................................................................... 48
Hardware Auto Flow Control .......................................................................................................................................... 49
Chapter 5 USB Interface ............................................................................................................................................................ 50
Introduction .................................................................................................................................................................... 50
USB HID Keyboard ........................................................................................................................................................ 51
USB Country Keyboard Types ................................................................................................................................ 52
Beep on Unknown Character .................................................................................................................................. 56
Emulate ALT+Keypad ............................................................................................................................................. 57
Code Page ....................................................................................................................................................... 58
Unicode Encoding ............................................................................................................................................ 60
Emulate Keypad with Leading Zero ................................................................................................................. 60
Function Key Mapping ............................................................................................................................................ 61
ASCII Function Key Mapping Table......................................................................................................................... 62
ASCII Function Key Mapping Table (Continued) ..................................................................................................... 63
Inter-Keystroke Delay.............................................................................................................................................. 64
Caps Lock ............................................................................................................................................................... 65
Convert Case .......................................................................................................................................................... 66
Emulate Numeric Keypad ....................................................................................................................................... 67
Fast Mode ............................................................................................................................................................... 69
Polling Rate............................................................................................................................................................. 70
USB CDC ....................................................................................................................................................................... 72
HID POS (POS HID Barcode Scanner) .......................................................................................................................... 73
Introduction ............................................................................................................................................................. 73
Access the Scanner with Your Program .................................................................................................................. 73
Acquire Scanned Data ............................................................................................................................................ 74
Send Command to the Scanner .............................................................................................................................. 74
IBM SurePOS (Tabletop) ................................................................................................................................................ 75
IBM SurePOS (Handheld) .............................................................................................................................................. 75
VID/PID .......................................................................................................................................................................... 75
Chapter 6 Symbologies.............................................................................................................................................................. 76
Introduction .................................................................................................................................................................... 76
Global Settings ............................................................................................................................................................... 76
Enable/Disable All Symbologies .............................................................................................................................. 76
Enable/Disable 1D Symbologies ............................................................................................................................. 76
Enable/Disable 2D Symbologies ............................................................................................................................. 77
Enable/Disable Postal Symbologies ....................................................................................................................... 77
1D Twin Code ......................................................................................................................................................... 78
Surround GS1 Application Identifiers (AI’s) with Parentheses ................................................................................. 79
Code 128........................................................................................................................................................................ 80
Restore Factory Defaults ........................................................................................................................................ 80
Enable/Disable Code 128 ....................................................................................................................................... 80
Set Length Range for Code 128 ............................................................................................................................. 81
EAN-8 ............................................................................................................................................................................ 82
Enable/Disable EAN-8 ............................................................................................................................................ 82
Transmit Check Character ...................................................................................................................................... 82
2-Digit Add-On Code ............................................................................................................................................... 83
5-Digit Add-On Code ............................................................................................................................................... 84
Add-On Code Required........................................................................................................................................... 85
Convert EAN-8 to EAN-13 ...................................................................................................................................... 85
EAN-13 .......................................................................................................................................................................... 86
Enable/Disable EAN-13 .......................................................................................................................................... 86
2-Digit Add-On Code ............................................................................................................................................... 87
5-Digit Add-On Code ............................................................................................................................................... 88
EAN-13 Beginning with 290 Add-On Code Required .............................................................................................. 89
EAN-13 Beginning with 378/379 Add-On Code Required ....................................................................................... 89
UPC-E ............................................................................................................................................................................ 93
Enable/Disable UPC-E ............................................................................................................................................ 93
2-Digit Add-On Code ............................................................................................................................................... 94
5-Digit Add-On Code ............................................................................................................................................... 95
Transmit Preamble Character ................................................................................................................................. 96
Convert UPC-E to UPC-A ....................................................................................................................................... 96
UPC-A ............................................................................................................................................................................ 97
Enable/Disable UPC-A ............................................................................................................................................ 97
2-Digit Add-On Code ............................................................................................................................................... 98
5-Digit Add-On Code ............................................................................................................................................... 99
Add-On Code Required......................................................................................................................................... 100
Transmit Preamble Character ............................................................................................................................... 100
Coupon ........................................................................................................................................................................ 101
UPC-A/EAN-13 with Extended Coupon Code ....................................................................................................... 101
Coupon GS1 Databar Output ................................................................................................................................ 102
Interleaved 2 of 5 ......................................................................................................................................................... 103
Restore Factory Defaults ...................................................................................................................................... 103
Enable/Disable Interleaved 2 of 5 ......................................................................................................................... 103
Set Length Range for Interleaved 2 of 5 ............................................................................................................... 104
Check Character Verification................................................................................................................................. 105
ITF-14 .......................................................................................................................................................................... 106
Enable/Disable ITF-14 .......................................................................................................................................... 106
ITF-6 ............................................................................................................................................................................ 107
Enable/Disable ITF-6 ............................................................................................................................................ 107
Matrix 2 of 5 ................................................................................................................................................................. 108
Enable/Disable Matrix 2 of 5 ................................................................................................................................. 108
Set Length Range for Matrix 2 of 5 ....................................................................................................................... 109
Code 39 ........................................................................................................................................................................111
Restore Factory Defaults .......................................................................................................................................111
Enable/Disable Code 39 ........................................................................................................................................111
Transmit Start/Stop Character............................................................................................................................... 114
Enable/Disable Code 39 Full ASCII ...................................................................................................................... 114
Enable/Disable Code 32 (Italian Pharma Code) ................................................................................................... 115
Code 32 Prefix ...................................................................................................................................................... 115
Transmit Code 32 Start/Stop Character ................................................................................................................ 116
Transmit Code 32 Check Character ...................................................................................................................... 116
Codabar ....................................................................................................................................................................... 117
Enable/Disable Codabar ....................................................................................................................................... 117
Set Length Range for Codabar ............................................................................................................................. 118
Start/Stop Character ............................................................................................................................................. 120
Code 93 ....................................................................................................................................................................... 121
China Post 25............................................................................................................................................................... 124
Enable/Disable China Post 25 .............................................................................................................................. 124
Set Length Range for China Post 25 .................................................................................................................... 125
GS1-128 (UCC/EAN-128) ............................................................................................................................................ 127
Enable/Disable GS1-128....................................................................................................................................... 127
Set Length Range for GS1-128 ............................................................................................................................. 128
GS1 Databar (RSS) ..................................................................................................................................................... 129
Enable/Disable GS1 Databar ................................................................................................................................ 129
Transmit Application Identifier “01” ........................................................................................................................ 129
GS1 Composite (EAN·UCC Composite) ...................................................................................................................... 130
Enable/Disable GS1 Composite ............................................................................................................................ 130
Enable/Disable UPC/EAN Composite ................................................................................................................... 130
Code 11 ........................................................................................................................................................................ 131
Enable/Disable Code 11........................................................................................................................................ 131
Set Length Range for Code 11 .............................................................................................................................. 132
Transmit Check Character .................................................................................................................................... 134
ISBN ............................................................................................................................................................................. 135
Enable/Disable ISBN............................................................................................................................................. 135
Set ISBN Format ................................................................................................................................................... 136
ISSN ............................................................................................................................................................................. 137
Enable/Disable ISSN............................................................................................................................................. 137
Industrial 25.................................................................................................................................................................. 138
Enable/Disable Industrial 25 ................................................................................................................................. 138
Set Length Range for Industrial 25 ....................................................................................................................... 139
Standard 25.................................................................................................................................................................. 141
Enable/Disable Standard 25 ................................................................................................................................. 141
Set Length Range for Standard 25 ....................................................................................................................... 142
Plessey ........................................................................................................................................................................ 144
Enable/Disable Plessey ........................................................................................................................................ 144
Set Length Range for Plessey .............................................................................................................................. 145
MSI-Plessey ................................................................................................................................................................. 147
Enable/Disable MSI-Plessey ................................................................................................................................. 147
Set Length Range for MSI-Plessey ....................................................................................................................... 148
AIM 128 ........................................................................................................................................................................ 151
Enable/Disable AIM 128 ........................................................................................................................................ 151
Set Length Range for AIM 128 .............................................................................................................................. 152
ISBT 128 ...................................................................................................................................................................... 153
Enable/Disable ISBT 128 ...................................................................................................................................... 153
Code 49 ....................................................................................................................................................................... 154
Code 16K ..................................................................................................................................................................... 156
Enable/Disable Code 16K ..................................................................................................................................... 156
Set Length Range for Code 16K ........................................................................................................................... 157
PDF417 ........................................................................................................................................................................ 158
Enable/Disable PDF417 ........................................................................................................................................ 158
Set Length Range for PDF417 .............................................................................................................................. 159
PDF417 Twin Code ............................................................................................................................................... 160
PDF417 Inverse .................................................................................................................................................... 161
Character Encoding .............................................................................................................................................. 161
PDF417 ECI Output .............................................................................................................................................. 162
Micro PDF417 .............................................................................................................................................................. 163
Enable/Disable Micro PDF417 .............................................................................................................................. 163
Set Length Range for Micro PDF417 .................................................................................................................... 164
QR Code ...................................................................................................................................................................... 165
Enable/Disable QR Code ...................................................................................................................................... 165
Set Length Range for QR Code ............................................................................................................................ 166
QR Twin Code ....................................................................................................................................................... 167
QR Inverse ............................................................................................................................................................ 168
QR ECI Output ...................................................................................................................................................... 169
Micro QR Code ............................................................................................................................................................ 170
Enable/Disable Micro QR ...................................................................................................................................... 170
Set Length Range for Micro QR ............................................................................................................................ 171
Aztec ............................................................................................................................................................................ 172
Enable/Disable Aztec Code................................................................................................................................... 172
Set Length Range for Aztec Code ......................................................................................................................... 173
Read Multi-barcodes on an Image ........................................................................................................................ 174
Set the Number of Barcodes ................................................................................................................................. 175
Aztec ECI Output .................................................................................................................................................. 176
Data Matrix ................................................................................................................................................................... 177
Enable/Disable Data Matrix................................................................................................................................... 177
Set Length Range for Data Matrix ......................................................................................................................... 178
Data Matrix Twin Code .......................................................................................................................................... 179
Rectangular Barcode ............................................................................................................................................ 180
Data Matrix Inverse ............................................................................................................................................... 180
Data Matrix ECI Output ......................................................................................................................................... 181
Maxicode ...................................................................................................................................................................... 182
Enable/Disable Maxicode...................................................................................................................................... 182
Set Length Range for Maxicode ............................................................................................................................ 183
Chinese Sensible Code ................................................................................................................................................ 184
Enable/Disable Chinese Sensible Code................................................................................................................ 184
Set Length Range for Chinese Sensible Code...................................................................................................... 185
Chinese Sensible Twin Code ................................................................................................................................ 186
Chinese Sensible Code Inverse ............................................................................................................................ 187
GM Code ...................................................................................................................................................................... 188
Enable/Disable GM ............................................................................................................................................... 188
Set Length Range for GM ..................................................................................................................................... 189
Code One ..................................................................................................................................................................... 190
Enable/Disable Code One..................................................................................................................................... 190
Set Length Range for Code One ........................................................................................................................... 191
USPS Postnet .............................................................................................................................................................. 192
Enable/Disable USPS Postnet .............................................................................................................................. 192
USPS Intelligent Mail ................................................................................................................................................... 193
Enable/Disable USPS Intelligent Mail ................................................................................................................... 193
Royal Mail .................................................................................................................................................................... 194
Enable/Disable Royal Mail .................................................................................................................................... 194
USPS Planet ................................................................................................................................................................ 195
Enable/Disable USPS Planet ................................................................................................................................ 195
KIX Post ....................................................................................................................................................................... 196
Enable/Disable KIX Post ....................................................................................................................................... 196
Australian Postal .......................................................................................................................................................... 197
Enable/Disable Australian Postal .......................................................................................................................... 197
Specific OCR-B ............................................................................................................................................................ 198
Enable/Disable Specific OCR-B ............................................................................................................................ 198
Passport OCR .............................................................................................................................................................. 199
Enable/Disable Passport OCR .............................................................................................................................. 199
Chapter 7 Data Formatter ........................................................................................................................................................ 200
Introduction .................................................................................................................................................................. 200

Add a Data Format ....................................................................................................................................................... 200
Programming with Barcodes ................................................................................................................................. 200
Programming with Serial Commands .................................................................................................................... 203
Enable/Disable Data Formatter .................................................................................................................................... 204
Non-Match Error Beep ................................................................................................................................................. 205
Data Format Selection ................................................................................................................................................. 206
Change Data Format for a Single Scan ....................................................................................................................... 207
Clear Data Format........................................................................................................................................................ 208
Query Data Formats ..................................................................................................................................................... 208
Formatter Command Type 6 ........................................................................................................................................ 209
Send Commands .................................................................................................................................................. 209
Move Commands .................................................................................................................................................. 213
Search Commands ............................................................................................................................................... 215
Miscellaneous Commands .................................................................................................................................... 218
Chapter 8 Prefix & Suffix ......................................................................................................................................................... 224
Introduction .................................................................................................................................................................. 224

Global Settings ............................................................................................................................................................. 225
Enable/Disable All Prefixes/Suffixes...................................................................................................................... 225
Prefix Sequence ........................................................................................................................................................... 225
Custom Prefix............................................................................................................................................................... 226
Enable/Disable Custom Prefix .............................................................................................................................. 226
Set Custom Prefix ................................................................................................................................................. 226
AIM ID Prefix ................................................................................................................................................................ 227
Code ID Prefix .............................................................................................................................................................. 228
Restore All Default Code IDs ................................................................................................................................ 228
Modify Code ID ..................................................................................................................................................... 228
Custom Suffix ............................................................................................................................................................... 237
Enable/Disable Custom Suffix ............................................................................................................................... 237
Set Custom Suffix ................................................................................................................................................. 237
Data Packing ................................................................................................................................................................ 238
Introduction ........................................................................................................................................................... 238
Data Packing Options ........................................................................................................................................... 238
Terminating Character Suffix ........................................................................................................................................ 240
Enable/Disable Terminating Character Suffix ........................................................................................................ 240
Set Terminating Character Suffix........................................................................................................................... 240
Chapter 9 Batch Programming ................................................................................................................................................ 242
Introduction .................................................................................................................................................................. 242

Create a Batch Command ............................................................................................................................................ 243
Create a Batch Barcode ............................................................................................................................................... 243
Use Batch Barcode ...................................................................................................................................................... 244
Appendix ................................................................................................................................................................................... 245
Digit Barcodes .............................................................................................................................................................. 245

Save/Cancel Barcodes ................................................................................................................................................. 248
Factory Defaults Table.................................................................................................................................................. 249
AIM ID Table ................................................................................................................................................................. 258
Code ID Table .............................................................................................................................................................. 260
Symbology ID Number ................................................................................................................................................. 262
ASCII Table .................................................................................................................................................................. 264
Unicode Key Maps ....................................................................................................................................................... 268
Preface
Introduction
This manual provides detailed instructions for setting up and using the NLS-FM3080 desktop barcode scanner (hereinafter
referred to as “the FM30” or “the scanner”).
Chapter Description
 Chapter 1, Getting Started : Gives a general description of the FM30.
 Chapter 2, EasySet : Introduces a useful tool you can use to set up the FM30.
 Chapter 3, System Settings : Introduces three configuration methods and describes how to configure
general parameters of the FM30.
 Chapter 4, RS-232 Interface : Describes how to configure RS-232 communication parameters.
 Chapter 5, USB Interface : Describes how to configure USB communication parameters.
 Chapter 6, Symbologies : Lists all compatible symbologies and describes how to configure the
relevant parameters.
 Chapter 7, Data Formatter : Explains how to customize scanned data with the advanced data formatter.
 Chapter 8, Prefix & Suffix : Describes how to use prefix and suffix to customize scanned data.
 Chapter 9, Batch Programming : Explains how to integrate a complex programming task into a single barcode.
 Appendix : Provides factory defaults table and a bunch of frequently used programming
barcodes.
1
Explanation of Icons
This icon indicates something relevant to this manual.
This icon indicates this information requires extra attention from the reader.
This icon indicates handy tips that can help you use or configure the scanner with ease.
This icon indicates practical examples that can help you to acquaint yourself with operations.
2
Chapter 1 Getting Started
Introduction
The FM30 scanner reads a 1D or 2D barcode by capturing its image. Adopting the advanced technology
independently developed by Newland Auto-ID Tech, it provides users with Level mode, Sense mode, Continuous mode
and Pulse mode, tailored to different scanning needs.
An illustrated introduction to the FM30 scanner is included in this chapter. If you have an FM30 scanner at hand, make
good use of it to develop a better understanding of this manual. This chapter is written for normal users, maintenance staff
and software developers.
Features of the FM30

⚫ Snappy on-screen barcode capture
⚫ Higher resolution CMOS
⚫ Multiple color options for Good Read LED
⚫ IR/Light triggers
⚫ IP65-rated sealing
Unpacking
Open the package and take out the scanner and its accessories. Check to make sure everything on the packing list is
present and intact. If any contents are damaged or missing, please keep the original package and contact your dealer
immediately for after-sales service.
3
FM30 Scanner
4
Data Port Pinout
PIN Signal Type Function

1 AGND P Ground
2 nTRIG I Trigger signal input: active low
3 VCC P Power+ (DC5V)
4 TXD O RS-232 output
5 RXD I RS-232 input
6 CTS I Clear to send (RS-232)
7 RTS O Request to send (RS-232)
8 GND P Ground
9 D- I/O
USB signal
10 D+ I/O
Driving the nTRIG pin (PIN 2) on the data port low for over 10ms causes the scanner to start a scan and decode session. If
barcode is decoded, the scanner waits for the voltage at the nTrig pin to turn high (or the trigger to be released) after sending
the data to the Host. If the trigger is released during a scan attempt, the scanner immediately stops decoding.
Next decode session does not happen until the scanner receives active trigger signal (driving the nTRIG pin low) again.
As a decode session involves image capture, barcode decoding and other steps, it is suggested that the minimum interval
between triggers should exceed 50ms.
The following trigger circuit is provided for reference.
5
Connecting the Scanner to a Host Device
The scanner must be connected to a host device in actual application, such as PC, POS or any intelligent
terminal with USB or RS-232 port, using a USB or RS-232 cable.
USB
USB port on the host device
RS-232
RS-232 port on the host device
Note: Please check the port on the host device and purchase the cable accordingly.
6
Using USB Cable
Connect the scanner to a host device with a USB cable with RJ45 and USB connectors:
1. Plug the cable’s RJ45 connector into the data port on the scanner.
2. Plug the cable’s USB connector into the USB port on the host device.
7
Using RS-232 Cable
Connect the scanner to a host device with an RS-232 cable with RJ45, RS-232 connector and a power jack:
1. Plug the cable’s RJ45 connector into the data port on the scanner.
2. Plug the cable’s RS-232 connector into the RS-232 port on the host device.
3. Plug the power adapter into the power jack of the cable.
4. Connect the power adapter to a power outlet.
8
Dimensions (unit: mm)
9
Field of View (unit: mm)
Note: If the IR sensors on the scanner are blocked or covered, the Sense scan mode may not work properly.
10
Power On, Power Off, Reboot
Power on the scanner
Connect the scanner to a Host. Then the scanner will be turned on.
Power off the scanner

Remove the communication cable from the scanner; or remove the USB cable from the Host; or disconnect the power
adaptor from mains.
Reboot the scanner

If the scanner stops responding to input or runs abnormally, turn off the scanner and then turn it back on.
Scanning Instructions
When the scanner is in the Sense scan mode, you can follow the steps below to scan a barcode:
1. Present the barcode on mobile phone screen or paper to the center of the scan window.
2. For a successful read, the scanner will beep.
Maintenance
 The scan window should be kept clean.
 Do not scratch the scan window.
 Use soft brush to remove the stain from the scan window.
 Use the soft cloth to clean the window, such as eyeglass cleaning cloth.
 Do not spray any liquid on the scan window.
 Do not use any detergent to clean other parts of the device except for water.
Note: The warranty DOES NOT cover damages caused by inappropriate care and maintenance.
11
Chapter 2 EasySet
EasySet, developed by Fujian Newland Auto-ID Tech. Co., Ltd., is a configuration tool for Newland’s 1D/2D handheld
barcode scanner, fixed mount barcode scanners and OEM scan engines. Its main features include:
 View device & configuration information of online device
 Configure device
 Update firmware of online device
 Load/modify existing XML configuration file; save current settings to an XML file
 Create/print/save programming barcodes to a PDF or Word file
 View/edit/save image stored on online device in the original image/BMP/JPG/TIFF format
 Send serial commands to online device and receive device response
 Supported languages: Chinese and English.
EasySet supports 32-bit/64-bit Microsoft WinXP/Win7/Win 8/Win 8.1/Win 10 operating systems.
EasySet can communicate with device via one of the following interface: RS-232, USB COM Port Emulation (UFCOM driver
required), USB CDC (UFCOM driver required), USB DataPipe (UFCOM driver required), USB HID-POS.
12
Enter Setup
Chapter 3 System Settings
Introduction
There are three ways to configure the FM30: Barcode programming, command programming and Easyset programming.
Barcode Programming
The FM30 can be configured by scanning programming barcodes. All user programmable features/options are described
along with their programming barcodes/commands in the following sections.
This programming method is most straightforward. However, it requires manually scanning barcodes. As a result, errors are
more likely to occur.
Command Programming
The FM30 can also be configured by serial commands sent from the host device.
Users can design an application program to send those command strings to the scanners to perform device configuration.
For more information, refer to the Serial Programming Command Manual.
EasySet Programming
Besides the two methods mentioned above, you can conveniently perform scanner configuration through EasySet too.
EasySet is a Windows-based configuration tool particularly designed for Newland products, enabling users to gain access
to decoded data and captured images and to configure scanners. For more information about this tool, refer to the EasySet
User Guide.
13 ** Exit Setup
Enter Setup
Programming Barcode/ Programming Command/Function
The figure above is an example that shows you the programming barcode and command for the Enter Setup function:
1. The No Case Conversion barcode.
2. The No Case Conversion command.
3. The description of feature/option.
4. ** indicates factory default settings.
Note: “@” included in the programming command indicates permanent setting which means the setting will not be lost by
removing power from the scanner or turning off or rebooting it; whereas “#” included in the programming command indicates
temporary setting which means the setting will be lost by removing power from the scanner or turning off or rebooting it.
** Exit Setup 14
Enter Setup
Use of Programming Command

Besides the barcode programming method, the scanner can also be configured by serial commands (HEX) sent from the
host device. All commands must be entered in uppercase letters.
Command Syntax
Prefix StorageType Tag SubTag {Data} [,SubTag {Data}] [;Tag SubTag {Data}] […] Suffix
Prefix: “~<SOH>0000” (HEX: 7E 01 30 30 30 30), 6 characters.
StorageType: “@” (HEX: 40) or “#” (HEX: 23), 1 character. “@” means permanent setting which will not be lost by removing
power from the scanner or rebooting it; “#” means temporary setting which will be lost by removing power from the scanner
or rebooting it.
Tag: A 3-character case-sensitive field that identifies the desired command group. For example, all USB HID Keyboard
configuration settings are identified with a Tag of KBW.
SubTag: A 3-character case-sensitive field that identifies the desired parameter within the tag group. For example, the
SubTag for the keyboard layout is CTY.
Data: The value for a feature or parameter setting, identified by the Tag and SubTag.
Suffix: “;<ETX>” (HEX: 3B 03), 2 characters.
Multiple commands can be issued within one Prefix/Suffix sequence. For configuration commands, only the Tag, SubTag,
and Data fields must be repeated for each command in sequence. If an additional command is to be applied to the same
Tag, then the command is separated with a comma (,) and only the SubTag and Data fields of the additional commands
are issued. If the additional command requires a different Tag field, the command is separated from previous command by
a semicolon (;).
Query Commands
For query commands, the entry in the Data field in the syntax above is one of the following characters means:
* (HEX: 2A) What is the scanner’s current value for the setting(s).
& (HEX: 26) What is the factory default value for the setting(s).
^ (HEX: 5E) What is the range of possible values for the setting(s).
15 ** Exit Setup
Enter Setup
The value of the StoreType field in a query command can be either “@” (HEX: 40) or “#” (HEX: 23).
A query command with the SubTag field omitted means to query all the settings concerning a tag. For example, to query
all the current settings about Code 11, you should enter 7E 01 30 30 30 30 40 43 31 31 2A 3B 03 (i.e.
~<SOH>0000@C11*;<ETX>).
Responses
Different from command sequence, the prefix of a response consists of the six characters of “<STX><SOH>0000” (HEX:
02 01 30 30 30 30).
The scanner responds to serial commands with one of the following three responses:
<ACK> (HEX: 06) Indicates a good command which has been processed.
<NAK> (HEX: 15) Indicates a good configuration command with its Data field entry out of the allowable range for this
Tag and SubTag combination (e.g. an entry for an inter-keystroke delay of 100 when the field will
only allow 2 digits), or an invalid query command.
<ENQ> (HEX: 05) Indicates an invalid Tag or SubTag command.
When responding, the scanner echoes back the command sequence with the status character above inserted directly before
each of the punctuation marks (the comma or semicolon) in the command.
Examples
Example 1: Enable Code 11, set the minimum and maximum lengths to 12 and 22 respectively.
Enter: 7E 01 30 30 30 30 40 43 31 31 45 4E 41 31 2C 4D 49 4E 31 32 2C 4D 41 58 32 32 3B 03
(~<SOH>0000@C11ENA1,MIN12,MAX22;<ETX>)
Response: 02 01 30 30 30 30 40 43 31 31 45 4E 41 31 06 2C 4D 49 4E 31 32 06 2C 4D 41 58 32 32 06 3B 03
(<STX><SOH>0000@C11ENA1<ACK>,MIN12<ACK>,MAX22<ACK>;<ETX>)
Example 2: Query the current minimum and maximum lengths of Code 11.
Enter: 7E 01 30 30 30 30 40 43 31 31 4D 49 4E 2A 2C 4D 41 58 2A 3B 03
(~<SOH>0000@C11MIN*,MAX*;<ETX>)
Response: 02 01 30 30 30 30 40 43 31 31 4D 49 4E 31 32 06 2C 4D 41 58 32 32 06 3B 03
(<STX><SOH>0000@C11MIN12<ACK>,MAX22<ACK>;<ETX>)
** Exit Setup 16
Enter Setup
Use of Programming Barcodes

Scanning the Enter Setup barcode can enable the scanner to enter the setup mode. Then you can scan a number of
programming barcodes to configure your scanner. To exit the setup mode, scan the Exit Setup barcode or a non-
programing barcode, or reboot the scanner.
** Exit Setup
Enter Setup
Programming barcode data (i.e. the characters under programming barcode) can be transmitted to the host device. Scan
the appropriate barcode below to enable or disable the transmission of programming barcode data to the host device.
** Do Not Transmit Programming Barcode Data
Transmit Programming Barcode Data
17 ** Exit Setup
Enter Setup
Illumination
A couple of illumination options are provided to improve the lighting conditions during every image capture:
Normal: Illumination LEDs are turned on during image capture.
Always On: Illumination LEDs keep on after the scanner is powered on.
Off: Illumination LEDs are off all the time.
** Normal
Off
Always On
** Exit Setup 18
Enter Setup
Illumination LED Selection
Red LED
** White LED
Green LED
Blue LED
Good Read LED

The LED can be programmed to be On or Off to indicate good read.
** On
Off
19 ** Exit Setup
Enter Setup
Good Read LED Duration
This parameter sets the amount of time that the Good Read LED to remain on following a good read. It is programmable in
1ms increments from 1ms to 2,500ms.
Short (20ms)
Medium (120ms)
** Long (220ms)
Prolonged (320ms)
Custom (1 - 2,500ms）
Set the Good Read LED duration to 800ms:
1. Scan the Enter Setup barcode.
2. Scan the Custom barcode.
3. Scan the numeric barcodes “8”, “0” and “0” from the “Digit Barcodes” section in Appendix.
4. Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix.
5. Scan the Exit Setup barcode.
** Exit Setup 20
Enter Setup
Good Read LED Selection
Red LED
White LED
** Green LED
Blue LED
Barcode Pay Mode
Note: When Barcode Pay Mode is selected, the scanner utilizes green, blue, and red LED(s) to indicate good read on
WeChat Pay barcode, Alipay barcode, and other barcode respectively.
21 ** Exit Setup
Enter Setup
Power On Beep
The scanner can be programmed to beep when it is powered on. Scan the Off barcode if you do not want a power on beep.
** On
Off
Good Read Beep

Scanning the Off barcode can turn off the beep that indicates successful decode; scanning the On barcode can turn it back
on.
** On
Off
** Exit Setup 22
Enter Setup
Good Read Beep Duration
This parameter sets the length of the beep the scanner emits on a good read. It is programmable in 1ms increments from
20ms to 300ms.
Short (40ms)
** Medium (80ms)
Long (120ms)
Custom (20 – 300ms)
Set the Good Read Beep duration to 200ms:
23 ** Exit Setup
Enter Setup
Good Read Beep Frequency
This parameter is programmable in 1Hz increments from 20Hz to 20,000Hz.
Extra Low (800Hz)
Low (1600Hz)
** Medium (2730Hz)
High (4200Hz)
Custom (20 - 20,000Hz)
Set the Good Read Beep frequency to 2,000Hz:
3. Scan the numeric barcodes “2”, “0”, “0” and “0” from the “Digit Barcodes” section in Appendix.
** Exit Setup 24
Enter Setup
Good Read Beep Volume
** Loud
Medium
Low
25 ** Exit Setup
Enter Setup
Scan Mode
Level Mode: A trigger pull activates a decode session. The decode session continues until a barcode is decoded or you
release the trigger.
Sense Mode: The scanner activates a decode session every time it detects a barcode presented to it. The decode session
continues until a barcode is decoded or the decode session timeout expires. Reread Timeout can avoid undesired rereading
of same barcode in a given period of time. Image Stabilization Timeout gives the scanner time to adapt to ambient
environment after it decodes a barcode and “looks” for another. Image Change Trigger Sensitivity can change the Sense
Mode’s sensibility to changes in images captured, while IR Proximity Trigger Sensitivity can adjust the Sense Mode’s
sensibility in detecting barcodes presented to the scanner.
Continuous Mode: The scanner automatically starts one decode session after another. To suspend/resume barcode
reading, simply press the trigger. Reread Timeout can avoid undesired rereading of same barcode in a given period of time.
Pulse Mode: When the trigger is pulled and released, scanning is activated until a barcode is decoded or the decode
session timeout expires (The decode session timeout begins when the trigger is released).
Level Mode
** Sense Mode
Continuous Mode
Pulse Mode
** Exit Setup 26
Enter Setup
Decode Session Timeout

This parameter sets the maximum time decode session continues during a scan attempt. It is programmable in 1ms
increments from 1ms to 3,600,000ms. When it is set to 0, the timeout is infinite. The default setting is 5,000ms.
Decode Session Timeout
Set the decode session timeout to 1,500ms:
2. Scan the Decode Session Timeout barcode.
27 ** Exit Setup
Enter Setup
Image Stabilization Timeout (Sense Mode)

This parameter defines the amount of time the scanner will spend adapting to ambient environment after it decodes a
barcode and “looks” for another. It is programmable in 1ms increments from 0ms to 3,000ms. The default setting is 100ms.
Image Stabilization Timeout
Set the image stabilization timeout to 800ms:
2. Scan the Image Stabilization Timeout barcode.
** Exit Setup 28
Enter Setup
Reread Timeout
Reread Timeout can avoid undesired rereading of same barcode in a given period of time. This feature is only applicable to
the Sense and Continuous modes.
Enable Reread Timeout: Do not allow the scanner to reread same barcode before the reread timeout expires.
Disable Reread Timeout: Allow the scanner to reread same barcode.
Enable Reread Timeout
** Disable Reread Timeout
The following parameter sets the time interval between two successive reads on same barcode. It is programmable in 1ms
increments from 0ms to 3,600,000ms. When it is set to a value greater than 3,000, the timeout for rereading same
programming barcode is limited to 3,000ms. The default setting is 1,500ms.
Set Reread Timeout
Set the reread timeout to 1,000ms:

2. Scan the Set Reread Timeout barcode.
29 ** Exit Setup
Enter Setup
You may wish to restart the reread timeout when the scanner encounters the same barcode that was decoded in the last
scan session before the reread timeout expires. To enable this feature, scan the Reread Timeout Reset On barcode. This
feature is only effective when Reread Timeout is enabled.
Reread Timeout Reset On
** Reread Timeout Reset Off
Image Decoding Timeout

Image Decoding Timeout specifies the maximum time the scanner will spend decoding an image. This parameter is
programmable in 1ms increments from 1ms to 3,000ms. The default timeout is 500ms.
Image Decoding Timeout
Set the image decoding timeout to 1,000ms:
2. Scan the Image Decoding Timeout barcode.
** Exit Setup 30
Enter Setup
Trigger Selection (Sense Mode)
Image Change Trigger
IR Proximity Trigger
** Both
31 ** Exit Setup
Enter Setup
Image Change Trigger Sensitivity
This specifies the degree of acuteness of the scanner’s response to changes in images captured. There are 20 levels to
choose from. The smaller the value, the higher the sensitivity and the lower requirement in image change to trigger the
scanner. You can select an appropriate degree of sensitivity that fits your application environment. This feature is only
applicable to the Sense mode.
Low Sensitivity
** Medium Sensitivity
High Sensitivity
Enhanced Sensitivity
Custom Sensitivity (Level 1-20)
Set the image change trigger sensitivity to Level 10:
2. Scan the Custom Sensitivity barcode.
3. Scan the numeric barcodes “1” and “0” from the “Digit Barcodes” section in Appendix.
** Exit Setup 32
Enter Setup
IR Proximity Trigger Sensitivity
This specifies the degree of acuteness of the scanner’s “sense” to detect barcodes presented to it. There are 10 levels to
choose from. The smaller the value, the higher the sensitivity and the further the scanner can reach. You can select an
appropriate degree of sensitivity that fits your application needs. The default setting is Level 1. This feature is only applicable
to the Sense mode.
Low Sensitivity
Medium Sensitivity
High Sensitivity
Custom Sensitivity (Level 1-10)
Set the IR proximity trigger sensitivity to Level 10:

2. Scan the Custom Sensitivity barcode.
33 ** Exit Setup
Enter Setup
Trigger Commands
When Enable Trigger Commands is selected, you can activate and deactivate the scanner in the Level mode with serial
trigger commands. Sending the Start Scanning command (default: <SOH> T <EOT>, user-programmable) to the scanner
in the Level mode activates a decode session. The decode session continues until a barcode is decoded or the decode
session timeout expires or the scanner receives the Stop Scanning command (default: <SOH> P <EOT>, user-
programmable).
** Disable Trigger Commands
Enable Trigger Commands
Modify Start Scanning Command
The Start Scanning command can consist of 1-10 characters (HEX values from 0x01 to 0xFF). In this command, the
character “?” (HEX: 0x3F) cannot be the first character. The default Start Scanning command is <SOH> T <EOT>.
Modify Start Scanning Command
Set the Start Scanning command to “*T”:
2. Scan the Modify Start Scanning Command barcode.
3. Scan the numeric barcodes “2”, “A”, “5” and “4” from the “Digit Barcodes” section in Appendix.
** Exit Setup 34
Enter Setup
Modify Stop Scanning Command
The Stop Scanning command can consist of 1-10 characters (HEX values from 0x01 to 0xFF). In this command, the
character “?” (HEX: 0x3F) cannot be the first character. The default Stop Scanning command is <SOH> P <EOT>.
Modify Stop Scanning Command
Set the Stop Scanning command to “*P”:
2. Scan the Modify Stop Scanning Command barcode.
3. Scan the numeric barcodes “2”, “A”, “5” and “0” from the “Digit Barcodes” section in Appendix.
Make a Beeping Sound

You may wish to force the scanner to beep upon a command sent from the host. A beeping sound is made to gain a user’s
attention to an error or other important event.
BEEPONxxxFyyyT (xxx: The desired frequency, 1-20,000Hz; yyy: The desired duration, 1-10,000ms)
Example: Make a 50ms beep at 2,000Hz
Enter: 7E 01 30 30 30 30 40 42 45 45 50 4F 4E 32 30 30 30 46 35 30 54 3B 03
(~<SOH>0000#BEEPON2000F50T;<ETX>)
Response: 02 01 30 30 30 30 40 42 45 45 50 4F 4E 32 30 30 30 46 35 30 54 06 3B 03
(<STX><SOH>0000#BEEPON2000F50T<ACK>;<ETX>)
35 ** Exit Setup
Enter Setup
Scanning Preference
Normal Mode: Select this mode when reading barcodes on paper.
Screen Mode: Select this mode when reading barcodes on the screen.
Barcode Pay Mode: Select this mode when reading barcodes to perform payment transactions, such as Alipay, WeChat
Pay barcodes.
** Normal Mode
Screen Mode
Barcode Pay Mode
Read Barcode On/Off

Sending the Read Barcode Off command ~<SOH>0000#SCNENA0;<ETX> to the scanner can disable it from reading
barcode, and the scanner is unable to scan barcode unless you send the Read Barcode On command
~<SOH>0000#SCNENA1;<ETX> to it or power cycle it. By default, Read Barcode is On.
** Exit Setup 36
Enter Setup
Decode Area
Whole Area Decoding: The scanner attempts to decode barcode(s) within its field of view, from the center to the periphery,
and transmits the barcode that has been first decoded.
Specific Area Decoding: The scanner attempts to read barcode(s) within a specified decoding area and transmits the
barcode that has been first decoded. This option allows the scanner to narrow its field of view to make sure it reads only
those barcodes intended by the user. For instance, if multiple barcodes are placed closely together, specific area decoding
in conjunction with appropriate pre-defined decoding area will insure that only the desired barcode is read.
** Whole Area Decoding
Specific Area Decoding
If Specific Area Decoding is enabled, the scanner only reads barcodes that intersect the predefined decoding area. The
default decoding area is an area of 40% top, 60% bottom, 40% left and 60% right of the scanner’s field of view
You can define the decoding area using the Top of Decoding Area, Bottom of Decoding Area, Left of Decoding Area
and Right of Decoding Area barcodes as well as numeric barcode(s) that represent(s) a desired percentage (0-100). The
value of Bottom must be greater than that of Top; the value of Right must be greater than that of Left.
Top of Decoding Area
Bottom of Decoding Area
Left of Decoding Area
Right of Decoding Area
37 ** Exit Setup
Enter Setup
Barcode 1
Barcode 2
Program the scanner to only read Barcode 1 in the figure above by setting the decoding area to
10% top, 45% bottom, 15% left and 30% right:
2. Scan the Top of Decoding Area barcode.
3. Scan the numeric barcode “0” from the “Digit Barcodes” section in Appendix.
5. Scan the Bottom of Decoding Area barcode.
8. Scan the Top of Decoding Area barcode.
11. Scan the Left of Decoding Area barcode.
14. Scan the Right of Decoding Area barcode.
17. Scan the Left of Decoding Area barcode.
** Exit Setup 38
Enter Setup
Image Flipping
** Do Not Flip
Flip Horizontally
Flip Vertically
Flip Horizontally & Vertically
Example of image not flipped Example of image flipped horizontally
Example of image flipped vertically Example of image flipped horizontally & vertically
39 ** Exit Setup
Enter Setup
Bad Read Message

Scan the appropriate barcode below to select whether or not to send a bad read message (user-programmable) when a
good read does not occur before trigger release, or the decode session timeout expires, or the scanner receives the Stop
Scanning command (For more information, see the “Serial Trigger Command” section in this Chapter).
** Bad Read Message OFF
Bad Read Message ON
Set Bad Read Message
A bad read message can contain up to 7 characters (HEX values from 0x00 to 0xFF). To set a bad read message, scan the
Set Bad Read Message barcode, the numeric barcodes representing the hexadecimal values of desired character(s) and
the Save barcode. The default setting is “NG”.
Set Bad Read Message
Set the bad read message to “F” (HEX: 0x46):
2. Scan the Set Bad Read Message barcode.
** Exit Setup 40
Enter Setup
Default Settings
Factory Defaults
Scanning the following barcode can restore the scanner to the factory defaults.
You may need to reset all parameters to the factory defaults when:
 scanner is not properly configured so that it fails to decode barcodes.
 you forget previous configuration and want to avoid its impact.
Restore All Factory Defaults
Custom Defaults
Scanning the Restore All Custom Defaults barcode can reset all parameters to the custom defaults. Scanning the Save
as Custom Defaults barcode can set the current settings as custom defaults.
Custom defaults are stored in the non-volatile memory.
Save as Custom Defaults
Restore All Custom Defaults
Restoring the scanner to the factory defaults will not remove the custom defaults from the scanner.
41 ** Exit Setup
Enter Setup
Query Product Information

After scanning the barcode below, the product information (including product name, firmware version, decoder version,
hardware version, product serial number, OEM serial number and manufacturing date) will be sent to the host device.
Query Product Information
Query Product Name
Query Product Name
Query Firmware Version
Query Firmware Version
** Exit Setup 42
Enter Setup
Query Decoder Version
Query Decoder Version
Query Hardware Version
Query Hardware Version
Query Product Serial Number
Query Product Serial Number
43 ** Exit Setup
Enter Setup
Query Manufacturing Date
Query Manufacturing Date
Query OEM Serial Number
Query OEM Serial Number
Query Data Formatter Version
Query Data Formatter Version
** Exit Setup 44
Enter Setup
Chapter 4 RS-232 Interface
Introduction
When the scanner is connected to the RS-232 port of a host device, scan the following barcode to enable RS-232
communication. Moreover, you need to set communication parameters (including baud rate, parity check, data bit and stop
bit) on the scanner to match the host device so that two devices can communicate with each other.
RS-232
45 ** Exit Setup
Enter Setup
Baud Rate
Baud rate is the number of bits of data transmitted per second. Set the baud rate to match the host requirements.
115200
57600
38400
19200
14400
** 9600
4800
2400
** Exit Setup 46
Enter Setup
Parity Check
Set the parity type to match the host requirements.
 Odd Parity: If the data contains an odd number of 1 bits, the parity bit value is set to 0.
 Even Parity: If the data contains an even number of 1 bits, the parity bit value is set to 0.
 None: Select this option when no parity bit is required.
** None
Even Parity
Odd Parity
47 ** Exit Setup
Enter Setup
Data Bit
Set the number of data bits to match the host requirements.
7 Data Bits
** 8 Data Bits
Stop Bit
The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the
receiving device for the next character in the serial data stream. Set the number of stop bits to match the host requirements.
** 1 Stop Bit
2 Stop Bits
** Exit Setup 48
Enter Setup
Hardware Auto Flow Control

If this feature is enabled, the scanner determines whether to transmit data based on CTS signal level. When CTS signal is
at a low level which means the serial port’s cache memory of receiving device (such as PC) is full, the scanner sends data
through RS-232 port until CTS signal is set to high level by receiving device. When the scanner is not ready for receiving, it
will set RTS signal to low level. When sending device (such as PC) detects it, it will not send data to the scanner any more
to prevent data loss.
If this feature is disabled, reception/transmission of serial data will not be influenced by RTS/CTS signal.
** Disable Hardware Auto Flow Control
Enable Hardware Auto Flow Control
Before enabling this feature, make sure that RTS/CTS signal lines are contained in RS-232 cable. Without
the signal lines, RS-232 communication errors will occur.
49 ** Exit Setup
Enter Setup
Chapter 5 USB Interface
Introduction
There are four options for USB connection:
 USB HID Keyboard: The scanner’s transmission is simulated as USB keyboard input with no need for command
configuration or a driver. Barcode data could be entered by the virtual keyboard directly and it is also convenient for
the host device to receive data.
 USB CDC: It is compliant with the standard USB CDC class specifications defined by the USB-IF and allows the host
device to receive data in the way as a serial port does. A driver is needed when using this feature.
 HID POS (POS HID Barcode Scanner): It is based on the HID interface, with no need for a custom driver. It excels
virtual keyboard and traditional RS-232 interface in transmission speed.
 IBM SurePOS: It conforms to IBM (now Toshiba Global Commerce Solutions) 4698 USB scanner interface
specifications.
When the scanner is connected to both USB and RS-232 ports on a host device, it will select the USB connection by default.
** Exit Setup 50
Enter Setup
USB HID Keyboard

When the scanner is connected to the USB port on a host device, you can enable the USB HID Keyboard feature by
scanning the barcode below. Then scanner’s transmission will be simulated as USB keyboard input. The Host receives
keystrokes onthe virtual keyboard. It works on a Plug and Play basis and no driver is required.
** USB HID Keyboard
If the host device allows keyboard input, then no extra software is needed for HID Keyboard input.
51 ** Exit Setup
Enter Setup
USB Country Keyboard Types
Keyboard layouts vary from country to country. The default setting is U.S. keyboard.
** U.S. (English)
Belgium
Brazil
Canada (French)
Czechoslovakia
Denmark
Finland (Swedish)
** Exit Setup 52
Enter Setup
France
Germany/ Austria
Greece
Hungary
Israel (Hebrew)
Italy
Latin America/ South America
Netherlands (Dutch)
53 ** Exit Setup
Enter Setup
Norway
Poland
Portugal
Romania
Russia
Slovakia
Spain
Sweden
** Exit Setup 54
Enter Setup
Switzerland (German)
Turkey_F
Turkey_Q
UK
Japan
55 ** Exit Setup
Enter Setup
Beep on Unknown Character
Due to the differences in keyboard layouts, some characters contained in barcode data may be unavailable on the selected
keyboard. As a result, the scanner fails to transmit the unknown characters.
Scan the appropriate barcode below to enable or disable the emission of beep when an unknown character is detected.
** Do Not Beep on Unknown Character
Beep on Unknown Character
Supposing French keyboard (Country Code: 7) is selected and barcode data ”AÐF” is being dealted with,
the keyboard will fail to locate the “Ð” (0xD0) character and the scanner will ignore the character and
continue to process the next one.
Do Not Beep on Unknown Character: The scanner does not beep and the Host receives “AF”.
Beep on Unknown Character: The scanner beeps and the Host still receives “AF”.
If Emulate ALT+Keypad ON is selected, Beep on Unknown Character does not function.
** Exit Setup 56
Enter Setup
Emulate ALT+Keypad
When Emulate ALT+Keypad is turned on, any character whose ASCII value is greater than or equal to 0x20 is sent over
the numeric keypad no matter which keyboard type is selected.
1. ALT Make
2. Enter the number corresponding to a desired character on the keypad.
3. ALT Break
After Emulate ALT+Keypad ON is selected, you need to choose the code page with which the barcodes were created and
to turn Unicode Encoding On or Off depending on the encoding used by the application software.
** Emulate ALT+Keypad OFF
Emulate ALT+Keypad ON
Since sending a character involves multiple keystroke emulations, this method appears less efficient.
Supposing Emulate ALT+Keypad is ON, Unicode Encoding is Off, Code Page 1252 (West European
Latin) is selected, and Emulate Keypad with Leading Zero is Off, barcode data ”AÐF” (65/208/70) is
sent as below:
“A” – “ALT Make” + “065” + “ALT Break”
“Ð” -- “ALT Make” + “208” + “ALT Break”
“F” -- “ALT Make” + “070” + “ALT Break”
57 ** Exit Setup
Enter Setup
Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the barcode being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, select the code page with which the barcodes were created by scanning the
appropriate barcode below. For PDF417, QR Code, Aztec and Data Matrix, besides setting the code page, you also need
to set the character encoding in the “Character Encoding” section in Chapter 6. This feature is only effective when Emulate
ALT+Keypad is turned on.
** Code Page 1252 (West European Latin)
Code Page 1251 (Cyrillic)
Code Page 1250 (Central and East European Latin)
Code Page 1253 (Greek)
Code Page 1254 (Turkish)
Code Page 1255 (Hebrew)
** Exit Setup 58
Enter Setup
Code Page 1256 (Arabic)
Code Page 1257 (Baltic)
Code Page 1258 (Vietnamese)
Code Page 936 (Simplified Chinese, GB2312,GBK）
Code Page 950 (Traditional Chinese, Big5)
Code Page 874 (Thai)
59 ** Exit Setup
Enter Setup
Unicode Encoding
Different host program may use different character encodings for handling incoming barcode data. For instance, Microsoft
Office Word uses Unicode encoding and therefore you should turn Unicode Encoding on, whereas Microsoft Office Excel
or Notepad uses Code Page encoding and therefore you should turn Unicode Encoding off. This feature is only effective
when Emulate ALT+Keypad is turned on.
** Off
On
Emulate Keypad with Leading Zero
You may turn this feature on to send character sequences sent over the numeric keypad as ISO characters which have a
leading zero. For example, ASCII A transmits as “ALT MAKE” 0065 “ALT BREAK”. This feature is only effective when
Emulate ALT+Keypad is enabled.
** On
Off
** Exit Setup 60
Enter Setup
Function Key Mapping
When Ctrl+ASCII Mode is selected, function characters (0x00 - 0x1F) are sent as ASCII sequences.
** Disable
Ctrl+ASCII Mode
Alt+Keypad Mode
If Ctrl+ASCII Mode is selected and other parameters of USB HID Keyboard adopt factory defaults,
barcode data “A<HT>(i.e. Horizontal Tab)F” (0x41/0x09/0x46) is sent as below:
“A” - Keystroke “A”.
<HT> - “Ctrl Make” + Keystroke “I” + “Ctrl Break”
“F” - Keystroke “F”
For some text editors, “Ctrl I” means italic convert. So the output may be “AF”.
If Alt+Keypad Mode is selected and other parameters of USB HID Keyboard adopt factory defaults, the
data above is sent as below:
“A” - Keystroke “A”.
<HT> - “Alt Make” + Keystrokes “009” + “Alt Break”
“F” - Keystroke “F”
61 ** Exit Setup
Enter Setup
ASCII Function Key Mapping Table
ASCII Function ASCII Value (HEX) Function Key Mapping Disabled Ctrl+ASCII
NUL 00 Null Ctrl+@
SOH 01 Keypad Enter Ctrl+A
STX 02 Caps Lock Ctrl+B
ETX 03 ALT Ctrl+C
EOT 04 Null Ctrl+D
ENQ 05 CTRL Ctrl+E
ACK 06 Null Ctrl+F
BEL 07 Enter Ctrl+G
BS 08 Left Arrow Ctrl+H
HT 09 Horizontal Tab Ctrl+I
LF 0A Down Arrow Ctrl+J
VT 0B Vertical Tab Ctrl+K
FF 0C Delete Ctrl+L
CR 0D Enter Ctrl+M
SO 0E Insert Ctrl+N
SI 0F Esc Ctrl+O
DLE 10 F11 Ctrl+P
DC1 11 Home Ctrl+Q
DC2 12 PrintScreen Ctrl+R
DC3 13 Backspace Ctrl+S
DC4 14 tab+shift Ctrl+T
NAK 15 F12 Ctrl+U
SYN 16 F1 Ctrl+V
ETB 17 F2 Ctrl+W
CAN 18 F3 Ctrl+X
EM 19 F4 Ctrl+Y
SUB 1A F5 Ctrl+Z
ESC 11 F6 Ctrl+[
FS 1C F7 Ctrl+\
GS 1D F8 Ctrl+]
RS 1E F9 Ctrl+6
US 1F F10 Ctrl+-
** Exit Setup 62
Enter Setup
ASCII Function Key Mapping Table (Continued)
The last five characters (0x1B~0x1F) in the table above apply to US keyboard layout only. The following chart provides the
equivalents of these five characters for other countries.
Country Ctrl+ASCII
United States Ctrl+[ Ctrl+\ Ctrl+] Ctrl+6 Ctrl+-
Belgium Ctrl+[ Ctrl+< Ctrl+] Ctrl+6 Ctrl+-
Scandinavia Ctrl+8 Ctrl+< Ctrl+9 Ctrl+6 Ctrl+-
France Ctrl+^ Ctrl+8 Ctrl+$ Ctrl+6 Ctrl+=
Germany Ctrl+Ã Ctrl++ Ctrl+6 Ctrl+-
Italy Ctrl+\ Ctrl++ Ctrl+6 Ctrl+-
Switzerland Ctrl+< Ctrl+.. Ctrl+6 Ctrl+-
United Kingdom Ctrl+[ Ctrl+￠ Ctrl+] Ctrl+6 Ctrl+-
Denmark Ctrl+8 Ctrl+\ Ctrl+9 Ctrl+6 Ctrl+-
Norway Ctrl+8 Ctrl+\ Ctrl+9 Ctrl+6 Ctrl+-
Spain Ctrl+[ Ctrl+\ Ctrl+] Ctrl+6 Ctrl+-
63 ** Exit Setup
Enter Setup
Inter-Keystroke Delay
This parameter specifies the delay between emulated keystrokes.
** No Delay
Long Delay (40ms)
Short Delay (20ms)
** Exit Setup 64
Enter Setup
Caps Lock
The Caps Lock On options can invert upper and lower case characters contained in barcode data. This inversion occurs
regardless of the state of Caps Lock key on the host device’s keyboard. To disable this feature, scan the appropriate Caps
Lock OFF barcode below based on your keyboard.
** Caps Lock OFF, Non-Japanese Keyboard
Caps Lock ON, Non-Japanese Keyboard
Caps Lock OFF, Japanese Keyboard
Caps Lock ON, Japanese Keyboard
Emulate ALT+Keypad ON/ Convert All to Upper Case/ Convert All to Lower Case prevails over Caps
Lock ON.
When the Caps Lock ON feature is selected, barcode data “AbC” is transmitted as “aBc”.
65 ** Exit Setup
Enter Setup
Convert Case
Scan the appropriate barcode below to convert all bar code data to your desired case.
** No Case Conversion
Convert All to Upper Case
Convert All to Lower Case
When the Convert All to Lower Case feature is enabled, barcode data “AbC” is transmitted as “abc”.
If Emulate ALT+Keypad ON is selected, Convert All to Lower Case and Convert All to Upper Case
do not function.
** Exit Setup 66
Enter Setup
Emulate Numeric Keypad
 Do Not Emulate Numeric Keypad 1: Sending a number (0-9) is emulated as keystroke(s) on main keyboard.
 Emulate Numeric Keypad 1: Sending a number (0-9) is emulated as keystroke(s) on numeric keypad. The state of
Num Lock on the simulated numeric keypad is determined by its equivalent on the host device. If Num Lock on the
host device is turned off, the output of simulated numeric keypad is function key instead of number.
 Do Not Emulate Numeric Keypad 2: Sending “+”, “－”, “*” and “/” is emulated as keystroke(s) on main keyboard.
 Emulate Numeric Keypad 2: Sending “+”, “－”, “*” and “/” is emulated as keystroke(s) on numeric keypad.
** Do Not Emulate Numeric Keypad 1
Emulate Numeric Keypad 1
67 ** Exit Setup
Enter Setup
** Do Not Emulate Numeric Keypad 2
Emulate Numeric Keypad 2
Emulate ALT+Keypad ON prevails over Emulate Numeric Keypad.
Supposing the Emulate Numeric Keypad 1 feature is enabled:
if Num Lock on the host device is ON, “A4.5” is transmitted as “A4.5”;
if Num Lock on the host device is OFF, “A4.5” is transmitted as “.A”:
1. “A” is sent on main keyboard;
2. “4” is sent as the function key “Cursor Move to Left”;
3. “.” is sent on main keyboard;
4. “5” is not sent as it does not correspond to any function key.
** Exit Setup 68
Enter Setup
Fast Mode
When Fast Mode On is selected, the scanner sends characters to the Host faster. If the Host drops characters, turn the
Fast Mode off or change the polling rate to a bigger value.
** Fast Mode Off
Fast Mode On
69 ** Exit Setup
Enter Setup
Polling Rate
This parameter specifies the polling rate for a USB keyboard. If the Host drops characters, change the polling rate to a
bigger value.
** 1ms
2ms
3ms
4ms
5ms
6ms
7ms
** Exit Setup 70
Enter Setup
8ms
9ms
10ms
71 ** Exit Setup
Enter Setup
USB CDC
If your scanner is connected to the USB port on a host device, the USB CDC feature allows the host device to receive data
in the way as a serial port does. A driver is needed when using this feature. You may download it from our website at
www.newlandaidc.com.
USB CDC
** Exit Setup 72
Enter Setup
HID POS (POS HID Barcode Scanner)

Introduction
The HID-POS interface is recommended for new application programs. It can send up to 56 characters in a single USB
report and appears more efficient than keyboard emulation.
Features:
 HID based, no custom driver required.
 Way more efficient in communication than keyboard emulation and traditional RS-232 interface.
USB HID-POS
Access the Scanner with Your Program
Use CreateFile to access the scanner as a HID device and then use ReadFile to deliver the scanned data to the application
program. Use WriteFile to send data to the scanner.
For detailed information about USB and HID interfaces, go to www.USB.org.
73 ** Exit Setup
Enter Setup
Acquire Scanned Data
After a barcode is decoded, the scanner sends an input report as below:
Bit
Byte 7 6 5 4 3 2 1 0
0 Report ID = 0x02
1 Barcode Length
2-57 Decoded Data (1-56)
58-61 Reserved
62 Newland Symbology Identifier or N/C: 0x00

Decoded data
63 - - - - - - - continued
Send Command to the Scanner
This output report is used to send commands to the scanner. All programming commands can be used.
Bit
Byte 7 6 5 4 3 2 1 0
0 Report ID = 0x04
1 Length of command
2-63 Command (1-62)
** Exit Setup 74
Enter Setup
IBM SurePOS (Tabletop)
IBM SurePOS (Tabletop)
IBM SurePOS (Handheld)
IBM SurePOS (Handheld)
VID/PID
USB uses VID (Vendor ID) and PID (Product ID) to identify and locate a device. The VID is assigned by USB Implementers
Forum. Newland’s vendor ID is 1EAB (Hex). A range of PIDs are used for each Newland product family. Every PID contains
a base number and interface type (keyboard, COM port, etc.).
Product Interface PID (Hex) PID (Dec)
USB HID Keyboard 0003 0003
USB CDC 0006 0006
FM3080 HID POS 0010 0016
IBM SurePOS (Tabletop) 0020 0032
IBM SurePOS(Handheld) 0021 0033
75 ** Exit Setup
Enter Setup
Chapter 6 Symbologies
Introduction
Every symbology (barcode type) has its own unique attributes. This chapter provides programming barcodes for configuring
the scanner so that it can identify various symbologies. It is recommended to disable those that are rarely used to increase
the efficiency of the scanner.
Global Settings
Enable/Disable All Symbologies
If the Disable All Symbologies feature is enabled, the scanner will not be able to read any non-programming barcodes
except the programming barcodes.
Enable All Symbologies
Disable All Symbologies
Enable/Disable 1D Symbologies
Enable 1D Symbologies
Disable 1D Symbologies
** Exit Setup 76
Enter Setup
Enable/Disable 2D Symbologies
Enable 2D Symbologies
Disable 2D Symbologies
Enable/Disable Postal Symbologies
Enable All Postal Symbologies
Disable All Postal Symbologies
77 ** Exit Setup
Enter Setup
1D Twin Code
1D twin code is two 1D barcodes of a symbology or of different symbologies paralleled vertically. Both barcodes must have
similar specifications and be placed closely together.
There are 3 options for reading 1D twin code:
 Single 1D Code Only: Read either 1D code.
 Twin 1D Code Only: Read both 1D codes. Transmission sequence: upper 1D code followed by lower 1D code.
 Both Single & Twin: Read both 1D codes. If successful, transmit as twin 1D code only. Otherwise, try single 1D code
only.
** Single 1D Code Only
Twin 1D Code Only
Both Single & Twin
** Exit Setup 78
Enter Setup
Surround GS1 Application Identifiers (AI’s) with Parentheses
When Surround GS1 AI’s with Parentheses is selected, each application identifier (AI) contained in scanned data will be
enclosed in parentheses in the output message.
** Do Not Surround GS1 AI’s with Parentheses
Surround GS1 AI’s with Parentheses
If Surround GS1 AI’s with Parentheses is selected, the barcode above is output as
(01)00614141999996(10)10ABCEDF123456.
If Do Not Surround GS1 AI’s with Parentheses is selected, the barcode above is output as
01006141419999961010ABCEDF123456.
79 ** Exit Setup
Enter Setup
Code 128
Restore Factory Defaults
Restore the Factory Defaults of Code 128
Enable/Disable Code 128
** Enable Code 128
Disable Code 128
If the scanner fails to identify Code 128 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Code 128 barcode.
** Exit Setup 80
Enter Setup
Set Length Range for Code 128
The scanner can be configured to only decode Code 128 barcodes with lengths that fall between (inclusive) the minimum
and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths.
Set the Minimum Length (Default: 1)
Set the Maximum Length (Default: 48)
If minimum length is set to be greater than maximum length, the scanner only decodes Code 128
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Code 128 barcodes with that length are to be decoded.
Set the scanner to decode Code 128 barcodes containing between 8 and 12 characters:
2. Scan the Set the Minimum Length barcode.
5. Scan the Set the Maximum Length barcode.
81 ** Exit Setup
Enter Setup
EAN-8
Restore the Factory Defaults of EAN-8
Enable/Disable EAN-8
** Enable EAN-8
Disable EAN-8
If the scanner fails to identify EAN-8 barcodes, you may first try this solution by scanning the Enter Setup
barcode and then Enable EAN-8 barcode.
Transmit Check Character
EAN-8 is 8 digits in length with the last one as its check character used to verify the integrity of the data.
** Transmit EAN-8 Check Character
Do Not Transmit EAN-8 Check Character
** Exit Setup 82
Enter Setup
2-Digit Add-On Code
An EAN-8 barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is a two-digit add-on code.
** Disable 2-Digit Add-On Code
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code: The scanner decodes EAN-8 and ignores the add-on code when
presented with an EAN-8 plus 2-digit add-on barcode. It can also decode EAN-8 barcodes without 2-digit
add-on codes.
Enable 2-Digit Add-On Code: The scanner decodes a mix of EAN-8 barcodes with and without 2-digit
add-on codes.
83 ** Exit Setup
Enter Setup
5-Digit Add-On Code
An EAN-8 barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is a five-digit add-on code.
presented with an EAN-8 plus 5-digit add-on barcode. It can also decode EAN-8 barcodes without 5-digit
add-on codes.
add-on codes.
** Exit Setup 84
Enter Setup
Add-On Code Required
When EAN-8 Add-On Code Required is selected, the scanner will only read EAN-8 barcodes that contain add-on codes.
** EAN-8 Add-On Code Not Required
EAN-8 Add-On Code Required
Convert EAN-8 to EAN-13
Convert EAN-8 to EAN-13: Convert EAN-8 decoded data to EAN-13 format before transmission. After conversion, the data
follows EAN-13 format and is affected by EAN-13 programming selections (e.g., Check Character).
Do Not Convert EAN-8 to EAN-13: EAN-8 decoded data is transmitted as EAN-8 data, without conversion.
** Do Not Convert EAN-8 to EAN-13
Convert EAN-8 to EAN-13
85 ** Exit Setup
Enter Setup
EAN-13
Restore the Factory Defaults of EAN-13
Enable/Disable EAN-13
** Enable EAN-13
Disable EAN-13
If the scanner fails to identify EAN-13 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable EAN-13 barcode.
** Exit Setup 86
Enter Setup
** Transmit EAN-13 Check Character
Do Not Transmit EAN-13 Check Character
2-Digit Add-On Code
An EAN-13 barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is an EAN-13 barcode while the part circled by red dotted line is a two-digit add-on code.
presented with an EAN-13 plus 2-digit add-on barcode. It can also decode EAN-13 barcodes without 2-
digit add-on codes.
add-on codes.
87 ** Exit Setup
Enter Setup
5-Digit Add-On Code
An EAN-13 barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is an EAN-13 barcode while the part circled by red dotted line is a five-digit add-on code.
presented with an EAN-13 plus 5-digit add-on barcode. It can also decode EAN-13 barcodes without 5-
digit add-on codes.
add-on codes.
When EAN-13 Add-On Code Required is selected, the scanner will only read EAN-13 barcodes that contain add-on codes.
** EAN-13 Add-On Code Not Required
EAN-13 Add-On Code Required
** Exit Setup 88
Enter Setup
EAN-13 Beginning with 290 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with “290”.
The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “290” must have a 2-digit or 5-digit add-on code. The EAN-13
barcode with the add-on code is then transmitted. If the required add-on code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable this feature, scan
Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your selection for the “Add-On Code
Required” feature.
** Do Not Require Add-On Code
Require Add-On Code
EAN-13 Beginning with 378/379 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with a “378”
or “379”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “378” or “379” must have a 2-digit or 5-digit add-on code.
The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not found, the EAN-13 barcode
is discarded.
Require Add-On Code
89 ** Exit Setup
Enter Setup
is discarded.
Require Add-On Code
is discarded.
Require Add-On Code
** Exit Setup 90
Enter Setup
Require Add-On Code
Require Add-On Code
91 ** Exit Setup
Enter Setup
Require Add-On Code
** Exit Setup 92
Enter Setup
UPC-E
Restore the Factory Defaults of UPC-E
Enable/Disable UPC-E
** Enable UPC-E0
Disable UPC-E0
Enable UPC-E1
** Disable UPC-E1
If the scanner fails to identify UPC-E0/UPC-E1 barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable UPC-E0/UPC-E1 barcode.
93 ** Exit Setup
Enter Setup
UPC-E is 8 digits in length with the last one as its check character used to verify the integrity of the data.
** Transmit UPC-E Check Character
Do Not Transmit UPC-E Check Character
2-Digit Add-On Code
A UPC-E barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is a two-digit add-on code.
Disable 2-Digit Add-On Code: The scanner decodes UPC-E and ignores the add-on code when
presented with a UPC-E plus 2-digit add-on barcode. It can also decode UPC-E barcodes without 2-digit
add-on codes.
Enable 2-Digit Add-On Code: The scanner decodes a mix of UPC-E barcodes with and without 2-digit
add-on codes.
** Exit Setup 94
Enter Setup
5-Digit Add-On Code
A UPC-E barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is a five-digit add-on code.
Disable 5-Digit Add-On Code: The scanner decodes UPC-E and ignores the add-on code when
presented with a UPC-E plus 5-digit add-on barcode. It can also decode UPC-E barcodes without 5-digit
add-on codes.
Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-E barcodes with and without 5-digit
add-on codes.
When UPC-E Add-On Code Required is selected, the scanner will only read UPC-E barcodes that contain add-on codes.
** UPC-E Add-On Code Not Required
UPC-E Add-On Code Required
95 ** Exit Setup
Enter Setup
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E barcode. Select one of
the following options for transmitting UPC-E preamble to the host device: transmit system character only, transmit system
character and country code (“0” for USA), or transmit no preamble.
** System Character
No Preamble
System Character & Country Code
Convert UPC-E to UPC-A
Convert UPC-E to UPC-A: Convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After
conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check
Character).
Do Not Convert UPC-E to UPC-A: UPC-E decoded data is transmitted as UPC-E data, without conversion.
** Do Not Convert UPC-E to UPC-A
Convert UPC-E to UPC-A
** Exit Setup 96
Enter Setup
UPC-A
Restore the Factory Defaults of UPC-A
Enable/Disable UPC-A
** Enable UPC-A
Disable UPC-A
If the scanner fails to identify UPC-A barcodes, you may first try this solution by scanning the Enter Setup
barcode and then Enable UPC-A barcode.
UPC-A is 13 digits in length with the last one as its check character used to verify the integrity of the data.
** Transmit UPC-A Check Character
Do Not Transmit UPC-A Check Character
97 ** Exit Setup
Enter Setup
2-Digit Add-On Code
A UPC-A barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is a two-digit add-on code.
Disable 2-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when
presented with a UPC-A plus 2-digit add-on barcode. It can also decode UPC-A barcodes without 2-digit
add-on codes.
Enable 2-Digit Add-On Code: The scanner decodes a mix of UPC-A barcodes with and without 2-digit
add-on codes.
** Exit Setup 98
Enter Setup
5-Digit Add-On Code
A UPC-A barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part
surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is a five-digit add-on code.
Disable 5-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when
presented with a UPC-A plus 5-digit add-on barcode. It can also decode UPC-A barcodes without 5-digit
add-on codes.
Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-A barcodes with and without 5-digit
add-on codes.
99 ** Exit Setup
Enter Setup
When UPC-A Add-On Code Required is selected, the scanner will only read UPC-A barcodes that contain add-on codes.
** UPC-A Add-On Code Not Required
UPC-A Add-On Code Required
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A barcode. Select one of
the following options for transmitting UPC-A preamble to the host device: transmit system character only, transmit system
character and country code (“0” for USA), or transmit no preamble.
** No Preamble
System Character
System Character & Country Code
** Exit Setup 100

Enter Setup
Coupon
UPC-A/EAN-13 with Extended Coupon Code
The following three types of coupon code + extended coupon code are supported:
 UPC-A (starting with “5”) + GS1-128
 UPC-A (starting with “5”) + GS1 Databar
 EAN-13 (starting with “99”) + GS1-128
Use the appropriate barcode below to enable or disable UPC-A/EAN-13 with Extended Coupon Code. When left on the
default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.
If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a
single scan, it transmits both as separate symbologies. Otherwise, it transmits the first coupon code it reads.
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code
in a single read to transmit the data. No data is output unless both codes are read.
** Off
Allow Concatenation
Require Concatenation
When using the UPC-A Coupon feature, please ensure that System Character or System Character &
Country Code is selected for the “Transmit UPC-A Preamble Character” feature.
101 ** Exit Setup

Enter Setup
Coupon GS1 Databar Output
If you scan coupons that have both UPC and GS1 Databar codes, you may wish to scan and output only the data from the
GS1 Databar code. Scan the GS1 Output On barcode below to scan and output only the GS1 Databar code data.
When GS1 Output Off is selected, coupons that have both UPC and GS1 Databar codes are transmitted depending on
your selection for the “UPC-A/EAN-13 with Extended Coupon Code” feature.
** GS1 Output Off
GS1 Output On
When using the UPC-A Coupon feature, please ensure that System Character or System Character &
Country Code is selected for the “Transmit UPC-A Preamble Character” feature.
** Exit Setup 102

Enter Setup
Interleaved 2 of 5
Restore the Factory Defaults of Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
** Enable Interleaved 2 of 5
Disable Interleaved 2 of 5
If the scanner fails to identify Interleaved 2 of 5 barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable Interleaved 2 of 5 barcode.
103 ** Exit Setup

Enter Setup
Set Length Range for Interleaved 2 of 5
The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between (inclusive) the
minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Interleaved 2 of 5
only Interleaved 2 of 5 barcodes with that length are to be decoded.
Set the scanner to decode Interleaved 2 of 5 barcodes containing between 8 and 12 characters:
** Exit Setup 104

Enter Setup
Check Character Verification
A check character is optional for Interleaved 2 of 5 and can be added as the last character. It is a calculated value used to
verify the integrity of the data.
 Disable: The scanner transmits Interleaved 2 of 5 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Interleaved 2 of 5
barcodes to verify that the data complies with the check character algorithm. Barcodes passing the check will be
transmitted except the last digit, whereas those failing it will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Interleaved 2 of 5 barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted,
whereas those failing it will not be transmitted.
Since Interleaved 2 of 5 must always have an even number of digits, a zero may need to be added as the first digit when
the check character is added. The check character is automatically generated when making Interleaved 2 of 5 barcodes.
** Disable
Do Not Transmit Check Character After Verification
Transmit Check Character After Verification
If the Do Not Transmit Check Character After Verification option is enabled, Interleaved 2 of 5
barcodes with a length that is less than the configured minimum length after having the check character
excluded will not be decoded. (For example, when the Do Not Transmit Check Character After
Verificationoption is enabled and the minimum length is set to 4, Interleaved 2 of 5 barcodes with a total
length of 4 characters including the check character cannot be read.)
105 ** Exit Setup

Enter Setup
ITF-14
ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the check character.
ITF-14 priority principle: Forthe Interleaved 2 of 5 barcodes with a length of 14 characters and the last character as the
check character, the ITF-14 configurations shall take precedence over the Interleaved 2 of 5 settings.
Restore the Factory Defaults of ITF-14
Enable/Disable ITF-14
** Disable ITF-14
Enable ITF-14 But Do Not Transmit Check Character
Enable ITF-14 and Transmit Check Character
An example of the ITF-14 priority principle: when ITF-14 is enabled and Interleaved 2 of 5 is disabled, the
scanner only decodes Interleaved 2 of 5 barcodes with a length of 14 characters and the last character
as the check character.
** Exit Setup 106

Enter Setup
ITF-6
ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the check character.
ITF-6 priority principle: For the Interleaved 2 of 5 barcodes with a length of 6 characters and the last character as the check
character, the ITF-6 configurations shall take precedence over the Interleaved 2 of 5 settings.
Restore the Factory Defaults of ITF-6
Enable/Disable ITF-6
** Disable ITF-6
Enable ITF-6 But Do Not Transmit Check Character
Enable ITF-6 and Transmit Check Character
An example of the ITF-6 priority principle: when ITF-6 is enabled and Interleaved 2 of 5 is disabled, the
scanner only decodes Interleaved 2 of 5 barcodes with a length of 6 characters and the last character as
the check character.
107 ** Exit Setup

Enter Setup
Matrix 2 of 5
Restore the Factory Defaults of Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5
** Disable Matrix 2 of 5
If the scanner fails to identify Matrix 2 of 5 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Matrix 2 of 5 barcode.
** Exit Setup 108

Enter Setup
Set Length Range for Matrix 2 of 5
The scanner can be configured to only decode Matrix 2 of 5 barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes Matrix 2 of 5
only Matrix 2 of 5 barcodes with that length are to be decoded.
Set the scanner to decode Matrix 2 of 5 barcodes containing between 8 and 12 characters:
109 ** Exit Setup

Enter Setup
A check character is optional for Matrix 2 of 5 and can be added as the last character. It is a calculated value used to verify
the integrity of the data.
 Disable: The scanner transmitsMatrix 2 of 5 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Matrix 2 of 5 barcodes
to verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted
except the last digit, whereas those failing it will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Matrix 2 of 5 barcodes to verify
that the data complies with the check character algorithm. Barcodes passing the check will be transmitted, whereas
those failing it will not be transmitted.
Since Matrix 2 of 5 must always have an even number of digits, a zero may need to be added as the first digit when the
check character is added. The check character is automatically generated when making Matrix 2 of 5 barcodes.
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Matrix 2 of 5 barcodes
with a length that is less than the configured minimum length after having the check character excluded
will not be decoded. (For example, when the Do Not Transmit Check Character After Verification
option is enabled and the minimum length is set to 4, Matrix 2 of 5 barcodes with a total length of 4
characters including the check character cannot be read.)
** Exit Setup 110

Enter Setup
Code 39
** Enable Code 39
Disable Code 39
111 ** Exit Setup

Enter Setup
If minimum length is set to be greater than maximum length, the scanner only decodes Code 39 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
39 barcodes with that length are to be decoded.
** Exit Setup 112

Enter Setup
A check character is optional for Code 39 and can be added as the last character. It is a calculated value used to verify the
integrity of the data.
 Disable: The scanner transmits Code 39 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Code 39 barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted except
the last digit, whereas those failing it will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Code 39 barcodes to verify that
the data complies with the check character algorithm. Barcodes passing the check will be transmitted, whereas those
failing it will not be transmitted.
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Code 39 barcodes with a
length that is less than the configured minimum length after having the check character excluded will not
be decoded. (For example, when the Do Not Transmit Check Character After Verification option is
enabled and the minimum length is set to 4, Code 39 barcodes with a total length of 4 characters including
the check character cannot be read.)
113 ** Exit Setup

Enter Setup
Transmit Start/Stop Character
Code 39 uses an asterisk (*) for both the start and the stop characters. You can choose whether or not to transmit the
start/stop characters by scanning the appropriate barcode below.
** Do Not Transmit Start/Stop Character
Enable/Disable Code 39 Full ASCII
The scanner can be configured to identify all ASCII characters by scanning the appropriate barcode below.
** Disable Code 39 Full ASCII
Enable Code 39 Full ASCII
** Exit Setup 114

Enter Setup
Enable/Disable Code 32 (Italian Pharma Code)
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable
or disable Code 32. Code 39 must be enabled and Code 39 check character verification must be disabled for this parameter
to function.
** Disable Code 32
Enable Code 32
Code 32 Prefix
Scan the appropriate barcode below to enable or disable adding the prefix character “A” to all Code 32 barcodes. Code 32
must be enabled for this parameter to function.
** Disable Code 32 Prefix
Enable Code 32 Prefix
115 ** Exit Setup

Enter Setup
Transmit Code 32 Start/Stop Character
Code 32 must be enabled for this parameter to function.
** Do Not Transmit Code 32 Start/Stop Character
Transmit Code 32 Start/Stop Character
Transmit Code 32 Check Character
Code 32 must be enabled for this parameter to function.
** Do Not Transmit Code 32 Check Character
** Exit Setup 116

Enter Setup
Codabar
Restore the Factory Defaults of Codabar
Enable/Disable Codabar
** Enable Codabar
Disable Codabar
If the scanner fails to identify Codabar barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Codabar barcode.
117 ** Exit Setup

Enter Setup
Set Length Range for Codabar
The scanner can be configured to only decode Codabar barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes Codabar barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Codabar
barcodes with that length are to be decoded.
Set the scanner to decode Codabar barcodes containing between 8 and 12 characters:
** Exit Setup 118

Enter Setup
A check character is optional for Codabar and can be added as the last character. It is a calculated value used to verify the
integrity of the data.
 Disable: The scanner transmits Codabar barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Codabar barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted except
the last digit, whereas those failing it will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Codabar barcodes to verify
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Codabar barcodes with
a length that is less than the configured minimum length after having the check character excluded will
not be decoded. (For example, when the Do Not Transmit Check Character After Verification option
is enabled and the minimum length is set to 4, Codabar barcodes with a total length of 4 characters
including the check character cannot be read.)
119 ** Exit Setup

Enter Setup
Start/Stop Character
You can set the start/stop characters and choose whether or not to transmit the start/stop characters by scanning the
appropriate barcode below.
** Do Not Transmit Start/Stop Character
** ABCD/ABCD as the Start/Stop Character
ABCD/TN*E as the Start/Stop Character
abcd/abcd as the Start/Stop Character
abcd/tn*e as the Start/Stop Character
** Exit Setup 120

Enter Setup
Code 93
** Enable Code 93
Disable Code 93
121 ** Exit Setup

Enter Setup
** Exit Setup 122

Enter Setup
Check characters are optional for Code 93 and can be added as the last two characters, which are calculated values used
to verify the integrity of the data.
 Disable: The scanner transmits Code 93 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Code 93 barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the checks will be transmitted
except the last two digits, whereas those failing them will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Code 93 barcodes to verify that
the data complies with the check character algorithm. Barcodes passing the checks will be transmitted, whereas those
failing them will not be transmitted.
Disable
** Do Not Transmit Check Character After Verification
If the Do Not Transmit Check Character After Verification option is enabled, Code 93 barcodes with a
length that is less than the configured minimum length after having the two check characters excluded
option is enabled and the minimum length is set to 4, Code 93 barcodes with a total length of 4 characters
including the two check characters cannot be read.)
123 ** Exit Setup

Enter Setup
China Post 25
Restore the Factory Defaults of China Post 25
Enable/Disable China Post 25
Enable China Post 25
** Disable China Post 25
If the scanner fails to identify China Post 25 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable China Post 25 barcode.
** Exit Setup 124

Enter Setup
Set Length Range for China Post 25
The scanner can be configured to only decode China Post 25 barcodes with lengths that fall between (inclusive) the
If minimum length is set to be greater than maximum length, the scanner only decodes China Post 25
only China Post 25 barcodes with that length are to be decoded.
Set the scanner to decode China Post 25 barcodes containing between 8 and 12 characters:
125 ** Exit Setup

Enter Setup
A check character is optional for China Post 25 and can be added as the last character. It is a calculated value used to verify
 Disable: The scanner transmits China Post 25 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all China Post 25 barcodes
 Transmit Check Character After Verification: The scanner checks the integrity of all China Post 25 barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted,
whereas those failing it will not be transmitted.
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, China Post 25 barcodes
option is enabled and the minimum length is set to 4, China Post 25 barcodes with a total length of 4
** Exit Setup 126

Enter Setup
GS1-128 (UCC/EAN-128)
Restore the Factory Defaults of GS1-128
Enable/Disable GS1-128
** Enable GS1-128
Disable GS1-128
If the scanner fails to identify GS1-128 barcodes, you may first try this solution by scanning the
EnterSetup barcode and then Enable GS1-128 barcode.
127 ** Exit Setup

Enter Setup
Set Length Range for GS1-128
The scanner can be configured to only decode GS1-128 barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes GS1-128 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only GS1-
Set the scanner to decode GS1-128 barcodes containing between 8 and 12 characters:
** Exit Setup 128

Enter Setup
GS1 Databar (RSS)

Restore the Factory Defaults of GS1 Databar
Enable/Disable GS1 Databar
** Enable GS1 Databar
Disable GS1 Databar
If the scanner fails to identify GS1 Databar barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable GS1 Databar barcode.
Transmit Application Identifier “01”
** Transmit Application Identifier “01”
Do Not Transmit Application Identifier “01”
129 ** Exit Setup

Enter Setup
GS1 Composite (EAN·UCC Composite)

Restore the Factory Defaults of GS1 Composite
Enable/Disable GS1 Composite
** Enable GS1 Composite
Disable GS1 Composite
If the scanner fails to identify GS1 Composite barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable GS1 Composite barcode.
Enable/Disable UPC/EAN Composite
Enable UPC/EAN Composite
** Disable UPC/EAN Composite
** Exit Setup 130

Enter Setup
Code 11
** Enable Code 11
Disable Code 11
131 ** Exit Setup

Enter Setup
** Exit Setup 132

Enter Setup
Check characters are optional for Code 11 and can be added as the last one or two characters, which are calculated values
used to verify the integrity of the data.
If the Disable option is enabled, the scanner transmits Code 11 barcodes as is.
Disable
** One Check Character, MOD11
Two Check Characters, MOD11/MOD11
One Check Character, MOD11 (Len<=10)

Two Check Characters, MOD11/MOD11(Len>10)
One Check Character, MOD11 (Len<=10)

Two Check Characters, MOD11/MOD9 (Len>10)
133 ** Exit Setup

Enter Setup
** Do Not Transmit Code 11 Check Character
If you select a check character algorithm and the Do Not Transmit Check Character option, Code 11
barcodes with a length that is less than the configured minimum length after having the check character(s)
excluded will not be decoded. (For example, when the One Check Character, MOD11 and Do Not
Transmit Check Character options are enabled and the minimum length is set to 4, Code 11 barcodes
with a total length of 4 characters including the check character cannot be read.)
** Exit Setup 134

Enter Setup
ISBN
Restore the Factory Defaults of ISBN
Enable/Disable ISBN
** Enable ISBN
Disable ISBN
If the scanner fails to identify ISBN barcodes, you may first try this solution by scanning the Enter Setup
barcode and then Enable ISBN barcode.
135 ** Exit Setup

Enter Setup
Set ISBN Format
** ISBN-10
ISBN-13
** Exit Setup 136

Enter Setup
ISSN
Restore the Factory Defaults of ISSN
Enable/Disable ISSN
Enable ISSN
** Disable ISSN
If the scanner fails to identify ISSN barcodes, you may first try this solution by scanning the Enter Setup
barcode and then Enable ISSN barcode.
137 ** Exit Setup

Enter Setup
Industrial 25
Restore the Factory Defaults of Industrial 25
Enable/Disable Industrial 25
** Enable Industrial 25
Disable Industrial 25
If the scanner fails to identify Industrial 25 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Industrial 25 barcode.
** Exit Setup 138

Enter Setup
Set Length Range for Industrial 25
The scanner can be configured to only decode Industrial 25 barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes Industrial 25
only Industrial 25 barcodes with that length are to be decoded.
Set the scanner to decode Industrial 25 barcodes containing between 8 and 12 characters:
139 ** Exit Setup

Enter Setup
A check character is optional for Industrial 25 and can be added as the last character. It is a calculated value used to verify
 Disable: The scanner transmits Industrial 25 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Industrial 25 barcodes
 Transmit Check Character After Verification: The scanner checks the integrity of all Industrial 25 barcodes to verify
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Industrial 25 barcodes
option is enabled and the minimum length is set to 4, Industrial 25 barcodes with a total length of 4
** Exit Setup 140

Enter Setup
Standard 25
Restore the Factory Defaults of Standard 25
Enable/Disable Standard 25
Enable Standard 25
** Disable Standard 25
If the scanner fails to identify Standard 25 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Standard 25 barcode.
141 ** Exit Setup

Enter Setup
Set Length Range for Standard 25
The scanner can be configured to only decode Standard 25 barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes Standard 25
only Standard 25 barcodes with that length are to be decoded.
Set the scanner to decode Standard 25 barcodes containing between 8 and 12 characters:
** Exit Setup 142

Enter Setup
A check character is optional for Standard 25 and can be added as the last character. It is a calculated value used to verify
 Disable: The scanner transmits Standard 25 barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Standard 25 barcodes
 Transmit Check Character After Verification: The scanner checks the integrity of all Standard 25 barcodes to verify
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Standard 25 barcodes
option is enabled and the minimum length is set to 4, Standard 25 barcodes with a total length of 4
143 ** Exit Setup

Enter Setup
Plessey
Restore the Factory Defaults of Plessey
Enable/Disable Plessey
** Enable Plessey
Disable Plessey
If the scanner fails to identify Plessey barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Plessey barcode.
** Exit Setup 144

Enter Setup
Set Length Range for Plessey
The scanner can be configured to only decode Plessey barcodes with lengths that fall between (inclusive) the minimum and
maximum lengths. To accomplish it, you need to set the minimum and maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Plessey
barcodes with that length are to be decoded.
Set the scanner to decode Plessey barcodes containing between 8 and 12 characters:
145 ** Exit Setup

Enter Setup
Check characters are optional for Plessey and can be added as the last two characters, which are calculated values used
to verify the integrity of the data.
 Disable: The scanner transmits Plessey barcodes as is.
 Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Plessey barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the checks will be transmitted
except the last two digits, whereas those failing them will not be transmitted.
 Transmit Check Character After Verification: The scanner checks the integrity of all Plessey barcodes to verify that
the data complies with the check character algorithm. Barcodes passing the checks will be transmitted, whereas those
failing them will not be transmitted.
** Disable
If the Do Not Transmit Check Character After Verification option is enabled, Plessey barcodes with a
length that is less than the configured minimum length after having the check characters excluded will not
be decoded. (For example, when the Do Not Transmit Check Character After Verification option is
enabled and the minimum length is set to 4, Plessey barcodes with a total length of 4 characters including
the check characters cannot be read.)
** Exit Setup 146

Enter Setup
MSI-Plessey
Restore the Factory Defaults of MSI-Plessey
Enable/Disable MSI-Plessey
** Enable MSI-Plessey
Disable MSI-Plessey
If the scanner fails to identify MSI-Plessey barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable MSI-Plessey barcode.
147 ** Exit Setup

Enter Setup
Set Length Range for MSI-Plessey
The scanner can be configured to only decode MSI-Plessey barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes MSI-Plessey
only MSI-Plessey barcodes with that length are to be decoded.
Set the scanner to decode MSI-Plessey barcodes containing between 8 and 12 characters:
** Exit Setup 148

Enter Setup
Check characters are optional for MSI-Plessey and can be added as the last one or two characters, which are calculated
values used to verify the integrity of the data.
If the Disable option is enabled, the scanner transmits MSI-Plessey barcodes as is.
Disable
** One Check Character, MOD10
149 ** Exit Setup

Enter Setup
** Transmit MSI-Plessey Check Character
Do Not Transmit MSI-Plessey Check Character
If you select a check character algorithm and the Do Not Transmit Check Character option, MSI-Plessey
barcodes with a length that is less than the configured minimum length after having the check character(s)
excluded will not be decoded. (For example, when the One Check Character, MOD10 and Do Not
Transmit Check Character options are enabled and the minimum length is set to 4, MSI-Plessey
barcodes with a total length of 4 characters including the check character cannot be read.)
** Exit Setup 150

Enter Setup
AIM 128
Restore the Factory Defaults of AIM 128
Enable/Disable AIM 128
** Enable AIM 128
Disable AIM 128
If the scanner fails to identify AIM 128 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable AIM 128 barcode.
151 ** Exit Setup

Enter Setup
Set Length Range for AIM 128
The scanner can be configured to only decode AIM 128 barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes AIM 128 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only AIM
Set the scanner to decode AIM 128 barcodes containing between 8 and 12 characters:
** Exit Setup 152

Enter Setup
ISBT 128
Restore the Factory Defaults of ISBT 128
Enable/Disable ISBT 128
Enable ISBT 128
** Disable ISBT 128
If the scanner fails to identify ISBT 128 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable ISBT 128 barcode.
153 ** Exit Setup

Enter Setup
Code 49
Enable Code 49
** Disable Code 49
** Exit Setup 154

Enter Setup
155 ** Exit Setup

Enter Setup
Code 16K
Restore the Factory Defaults of Code 16K
Enable/Disable Code 16K
Enable Code 16K
** Disable Code 16K
If the scanner fails to identify Code 16K barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Code 16K barcode.
** Exit Setup 156

Enter Setup
Set Length Range for Code 16K
The scanner can be configured to only decode Code 16K barcodes with lengths that fall between (inclusive) the minimum
If minimum length is set to be greater than maximum length, the scanner only decodes Code 16K
only Code 16K barcodes with that length are to be decoded.
Set the scanner to decode Code 16K barcodes containing between 8 and 12 characters:
157 ** Exit Setup

Enter Setup
PDF417
Restore the Factory Defaults of PDF417
Enable/Disable PDF417
** Enable PDF417
Disable PDF417
If the scanner fails to identify PDF417 barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable PDF417 barcode.
** Exit Setup 158

Enter Setup
Set Length Range for PDF417
The scanner can be configured to only decode PDF417 barcodes with lengths that fall between (inclusive) the minimum
Minimum length is not allowed to be greater than maximum length. If you only want to read PDF417
barcodes with a specific length, set both minimum and maximum lengths to be that desired length.
Set the scanner to decode PDF417 barcodes containing between 8 and 12 characters:
159 ** Exit Setup

Enter Setup
PDF417 Twin Code
PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must both be either regular or inverse
barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading PDF417 twin codes:
 Single PDF417 Only: Read either PDF417 code.
 Twin PDF417 Only: Read both PDF417 codes.
 Both Single & Twin: Read both PDF417 codes. If successful, transmit as twin PDF417 only. Otherwise, try single
PDF417 only.
** Single PDF417 Only
Twin PDF417 Only
Both Single & Twin
** Exit Setup 160

Enter Setup
PDF417 Inverse
Regular barcode: Dark bars on a bright background.
Inverse barcode: Bright bars on a dark background.
** Decode Regular PDF417 Barcodes Only
Decode Inverse PDF417 Barcodes Only
Decode Both
Character Encoding
** Default Character Encoding
UTF-8
161 ** Exit Setup

Enter Setup
PDF417 ECI Output
Disable PDF417 ECI Output
** Enable PDF417 ECI Output
** Exit Setup 162

Enter Setup
Micro PDF417
Restore the Factory Defaults of Micro PDF417
Enable/Disable Micro PDF417
Enable Micro PDF417
** Disable Micro PDF417
If the scanner fails to identify Micro PDF417 barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable Micro PDF417 barcode.
163 ** Exit Setup

Enter Setup
Set Length Range for Micro PDF417
The scanner can be configured to only decode Micro PDF417 barcodes with lengths that fall between (inclusive) the
Minimum length is not allowed to be greater than maximum length. If you only want to read Micro PDF417
Set the scanner to decode Micro PDF417 barcodes containing between 8 and 12 characters:
** Exit Setup 164

Enter Setup
QR Code
Restore the Factory Defaults of QR Code
Enable/Disable QR Code
** Enable QR Code
Disable QR Code
If the scanner fails to identify QR Code barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable QR Code barcode.
165 ** Exit Setup

Enter Setup
Set Length Range for QR Code
The scanner can be configured to only decode QR Code barcodes with lengths that fall between (inclusive) the minimum
Minimum length is not allowed to be greater than maximum length. If you only want to read QR Code
Set the scanner to decode QR Code barcodes containing between 8 and 12 characters:
** Exit Setup 166

Enter Setup
QR Twin Code
QR twin code is 2 QR barcodes paralleled vertically or horizontally. They must both be either regular or inverse barcodes.
They must have similar specifications and be placed closely together.
There are 3 options for reading QR twin codes:
 Single QR Only: Read either QR code.
 Twin QR Only: Read both QR codes. Transmission sequence: left (upper) QR code followed by right (lower) QR code.
 Both Single & Twin: Read both QR codes. If successful, transmit as twin QR only. Otherwise, try single QR only.
** Single QR Only
Twin QR Only
Both Single & Twin
167 ** Exit Setup

Enter Setup
QR Inverse
** Decode Regular QR Barcodes Only
Decode Inverse QR Barcodes Only
Decode Both
Character Encoding
UTF-8
** Exit Setup 168

Enter Setup
QR ECI Output
Disable QR ECI Output
** Enable QR ECI Output
169 ** Exit Setup

Enter Setup
Micro QR Code
Restore the Factory Defaults of Micro QR
Enable/Disable Micro QR
Enable Micro QR
** Disable Micro QR
If the scanner fails to identify Micro QR barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Micro QR barcode.
** Exit Setup 170

Enter Setup
Set Length Range for Micro QR
The scanner can be configured to only decode Micro QR barcodes with lengths that fall between (inclusive) the minimum
Minimum length is not allowed to be greater than maximum length. If you only want to read Micro QR
Set the scanner to decode Micro QR Code barcodes containing between 8 and 12 characters:
171 ** Exit Setup

Enter Setup
Aztec
Restore the Factory Defaults of Aztec Code
Enable/Disable Aztec Code
Enable Aztec Code
** Disable Aztec Code
If the scanner fails to identify Aztec Code barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Aztec Code barcode.
** Exit Setup 172

Enter Setup
Set Length Range for Aztec Code
The scanner can be configured to only decode Aztec barcodes with lengths that fall between (inclusive) the minimum and
Minimum length is not allowed to be greater than maximum length. If you only want to read Aztec barcodes
with a specific length, set both minimum and maximum lengths to be that desired length.
Set the scanner to decode Aztec barcodes containing between 8 and 12 characters:
173 ** Exit Setup

Enter Setup
Read Multi-barcodes on an Image
There are three options:
 Mode 1: Read one barcode only.
 Mode 2: Read fixed number of barcodes only.
 Mode 3: Composite Reading. Read fixed number of barcodes first. If unsuccessful, read one barcode only.
** Mode 1
Mode 2
Mode 3
** Exit Setup 174

Enter Setup
Set the Number of Barcodes
** 1
175 ** Exit Setup

Enter Setup
Character Encoding
UTF-8
Aztec ECI Output
Disable Aztec ECI Output
** Enable Aztec ECI Output
** Exit Setup 176

Enter Setup
Data Matrix
Restore the Factory Defaults of Data Matrix
Enable/Disable Data Matrix
** Enable Data Matrix
Disable Data Matrix
If the scanner fails to identify Data Matrix barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Data Matrix barcode.
177 ** Exit Setup

Enter Setup
Set Length Range for Data Matrix
The scanner can be configured to only decode Data Matrix barcodes with lengths that fall between (inclusive) the minimum
Minimum length is not allowed to be greater than maximum length. If you only want to read Data Matrix
Set the scanner to decode Data Matrix barcodes containing between 8 and 12 characters:
** Exit Setup 178

Enter Setup
Data Matrix Twin Code
Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally. They must both be either regular or
inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading Data Matrix twin codes:
 Single Data Matrix Only: Read either Data Matrix code.
 Twin Data Matrix Only: Read both Data Matrix codes. Transmission sequence: left (upper) Data Matrix code followed
by right (lower) Data Matrix code.
 Both Single & Twin: Read both Data Matrix codes. If successful, transmit as twin Data Matrix only. Otherwise, try
single Data Matrix only.
** Single Data Matrix Only
Twin Data Matrix Only
Both Single & Twin
179 ** Exit Setup

Enter Setup
Rectangular Barcode
Data Matrix has two formats:
Square barcodes having the same amount of modules in length and width: 10*10, 12*12.... 144*144.
Rectangular barcodes having different amounts of models in length and width: 6*16, 6*14...14*22.
** Enable Rectangular Barcode
Disable Rectangular Barcode
Data Matrix Inverse
** Decode Regular Data Matrix Barcodes Only
Decode Inverse Data Matrix Barcodes Only
Decode Both
** Exit Setup 180

Enter Setup
Character Encoding
UTF-8
Data Matrix ECI Output
Disable Data Matrix ECI Output
** Enable Data Matrix ECI Output
181 ** Exit Setup

Enter Setup
Maxicode
Restore the Factory Defaults of Maxicode
Enable/Disable Maxicode
Enable Maxicode
** Disable Maxicode
If the scanner fails to identify Maxicode barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Maxicode barcode.
** Exit Setup 182

Enter Setup
Set Length Range for Maxicode
The scanner can be configured to only decode Maxicode barcodes with lengths that fall between (inclusive) the minimum
Set the Maximum Length (Default:150)
Minimum length is not allowed to be greater than maximum length. If you only want to read Maxicode
Set the scanner to decode Maxicode barcodes containing between 8 and 12 characters:
183 ** Exit Setup

Enter Setup
Chinese Sensible Code

Restore the Factory Defaults of Chinese Sensible Code
Enable/Disable Chinese Sensible Code
Enable Chinese Sensible Code
** Disable Chinese Sensible Code
If the scanner fails to identify Chinese Sensible Code barcodes, you may first try this solution by scanning
the Enter Setup barcode and then Enable Chinese Sensible Code barcode.
** Exit Setup 184

Enter Setup
Set Length Range for Chinese Sensible Code
The scanner can be configured to only decode Chinese Sensible Code barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths.
Minimum length is not allowed to be greater than maximum length. If you only want to read Chinese
Sensible Code barcodes with a specific length, set both minimum and maximum lengths to be that desired
length.
Set the scanner to decode Chinese Sensible Code barcodes containing between 8 and 12 characters:
185 ** Exit Setup

Enter Setup
Chinese Sensible Twin Code
Chinese Sensible twin code is 2 Chinese Sensible barcodes paralleled vertically or horizontally. They must both be either
regular or inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading Chinese Sensible twin codes:
 Single Chinese Sensible Code Only: Read either Chinese Sensible code.
 Twin Chinese Sensible Code Only: Read both Chinese Sensible codes. Transmission sequence: left (upper)
Chinese Sensible code followed by right (lower) Chinese Sensible code.
 Both Single & Twin: Read both Chinese Sensible codes. If successful, transmit as twin Chinese Sensible Code only.
Otherwise, try single Chinese Sensible Code only.
** Single Chinese Sensible Code Only
Twin Chinese Sensible Code Only
Both Single & Twin
** Exit Setup 186

Enter Setup
Chinese Sensible Code Inverse
** Decode Regular Chinese Sensible Barcodes Only
Decode Inverse Chinese Sensible Barcodes Only
Decode Both
187 ** Exit Setup

Enter Setup
GM Code
Restore the Factory Defaults of GM
Enable/Disable GM
Enable GM
** Disable GM
If the scanner fails to identify GM barcodes, you may first try this solution by scanning the Enter Setup
barcode and then Enable GM barcode.
** Exit Setup 188

Enter Setup
Set Length Range for GM
The scanner can be configured to only decode GM barcodes with lengths that fall between (inclusive) the minimum and
Minimum length is not allowed to be greater than maximum length. If you only want to read GM barcodes
with a specific length, set both minimum and maximum lengths to be that desired length.
Set the scanner to decode GM barcodes containing between 8 and 12 characters:
189 ** Exit Setup

Enter Setup
Code One
Restore the Factory Defaults of Code One
Enable/Disable Code One
Enable Code One
** Disable Code One
If the scanner fails to identify Code One barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Code One barcode.
** Exit Setup 190

Enter Setup
Set Length Range for Code One
The scanner can be configured to only decode Code One barcodes with lengths that fall between (inclusive) the minimum
Minimum length is not allowed to be greater than maximum length. If you only want to read Code One
Set the scanner to decode Code One barcodes containing between 8 and 12 characters:
191 ** Exit Setup

Enter Setup
USPS Postnet
Restore the Factory Defaults of USPS Postnet
Enable/Disable USPS Postnet
Enable USPS Postnet
** Disable USPS Postnet
If the scanner fails to identify USPS Postnet barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable USPS Postnet barcode.
Do Not Transmit USPS Postnet Check Character
** Transmit USPS Postnet Check Character
** Exit Setup 192

Enter Setup
USPS Intelligent Mail

Restore the Factory Defaults of USPS Intelligent Mail
Enable/Disable USPS Intelligent Mail
Enable USPS Intelligent Mail
** Disable USPS Intelligent Mail
If the scanner fails to identify USPS Intelligent Mail barcodes, you may first try this solution by scanning
the Enter Setup barcode and then Enable USPS Intelligent Mail barcode.
193 ** Exit Setup

Enter Setup
Royal Mail
Restore the Factory Defaults of Royal Mail
Enable/Disable Royal Mail
Enable Royal Mail
** Disable Royal Mail
If the scanner fails to identify Royal Mail barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable Royal Mail barcode.
** Exit Setup 194

Enter Setup
USPS Planet
Restore the Factory Defaults of USPS Planet
Enable/Disable USPS Planet
Enable USPS Planet
** Disable USPS Planet
If the scanner fails to identify USPS Planet barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable USPS Planet barcode.
Do Not Transmit USPS Planet Check Character
** Transmit USPS Planet Check Character
195 ** Exit Setup

Enter Setup
KIX Post
Restore the Factory Defaults of KIX Post
Enable/Disable KIX Post
Enable KIX Post
** Disable KIX Post
If the scanner fails to identify KIX Post barcodes, you may first try this solution by scanning the Enter
Setup barcode and then Enable KIX Post barcode.
** Exit Setup 196

Enter Setup
Australian Postal
Restore the Factory Defaults of Australian Postal
Enable/Disable Australian Postal
Enable Australian Postal
** Disable Australian Postal
If the scanner fails to identify Australian Postal barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable Australian Postal barcode.
197 ** Exit Setup

Enter Setup
Specific OCR-B
Restore the Factory Defaults of Specific OCR-B
Enable/Disable Specific OCR-B
Enable Specific OCR-B
** Disable Specific OCR-B
If the scanner fails to identify Specific OCR-B barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable Specific OCR-B barcode.
** Exit Setup 198

Enter Setup
Passport OCR
Restore the Factory Defaults of Passport OCR
Enable/Disable Passport OCR
Enable Passport OCR
** Disable Passport OCR
If the scanner fails to identify Passport OCR barcodes, you may first try this solution by scanning the
Enter Setup barcode and then Enable Passport OCR barcode.
199 ** Exit Setup

Enter Setup
Chapter 7 Data Formatter
Introduction
You may use the Data Formatter to modify the scanner’s output. For example, you can use the Data Formatter to insert
characters at certain points in barcode data or to suppress/ replace/ send certain characters in barcode data as it is scanned.
Normally, when you scan a barcode, it gets outputted automatically; however, when you create a format, you must use a
“send” command (see the “Send Commands” section in this chapter) within the format programming to output data. Multiple
data formats can be programmed into the scanner. The maximum size of all data formats created is 2048 characters. By
default, the data formatter is disabled. Enable it when required. If you have changed data format settings, and wish to clear
all formats and return to the factory defaults, scan the Default Data Format code below.
Default Data Format
Add a Data Format

Data format is used to edit barcode data. When you create a data format, you must select one of the four labels (Format_0,
Format_1, Format_2 and Format_3) for your data format, specify the application scope of data format (such as barcode
type and data length) and include formatter commands. Multiple data formats may be created using the same label. When
scanned data does not match your data format requirements, you will hear the non-match error beep (if the non-match error
beep is ON).
There are two methods to program a data format: Programming with barcodes and programming with serial commands.
Programming with Barcodes
The following explains how to program a data format by scanning the specific barcodes. Scanning any irrelevant barcode
or failing to follow the setting procedure will result in programming failure. To find the alphanumeric barcodes needed to
create a data format, see the “Digit Barcodes” section in Appendix.
Step 1: Scan the Enter Setup barcode.
** Exit Setup 200

Enter Setup
Step 2: Scan the Add Data Format barcode.
Add Data Format
Step 3: Select a label (Format_0 or Format_1 or Format_2 or Format_3).

Scan a numeric barcode 0 or 1 or 2 or 3 to label this data format Format_0 or Format_1 or Format_2 or Format_3.
Step 4: Select formatter command type.

Specify what type of formatter commands will be used. Scan a numeric barcode 6 to select formatter command type 6. (See
the “Formatter Command Type 6” section in this chapter for more information)
Step 5: Set interface type

Scan 999 for any interface type.
Step 6: Set Symbology ID Number

Refer to the “Symbology ID Number” section in Appendix and find the ID number of the symbology to which you want to
apply the data format. Scan three numeric barcodes for the symbology ID number. If you wish to create a data format for all
symbologies, scan 999.
Step 7: Set barcode data length

Specify what length of data will be acceptable for this symbology. Scan the four numeric barcodes that represent the data
length. 9999 is a universal number, indicating all lengths. For example, 32 characters should be entered as 0032.
Step 8: Enter formatter command

Refer to the “Formatter Command Type 6” section in this chapter. Scan the alphanumeric barcodes that represent the
command you need to edit data. For example, when a command is F141, you should scan F141.
Step 9: Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix to save your data format.
201 ** Exit Setup

Enter Setup
Example: Program a Format_0 data format using formatter command type 6, Code 128 containing 10 characters applicable,
send all characters followed by “A”.
1. Scan the Enter Setup barcode Enter the Setup mode
2. Scan the Add Data Format barcode Add a data format
3. Scan the 0 barcode Select Format_0 as the label
4. Scan the 6 barcode Select formatter command type 6
5. Scan the 9 barcode three times All interface types applicable
6. Scan the barcodes 002 Only Code 128 applicable
7. Scan the barcodes 0010 Only a length of 10 characters applicable
8. Scan the alphanumeric barcodes F141 Send all characters followed by “A” (HEX: 41)
9. Scan the Save barcode Save the data format
To streamline the programming process, you may as well generate a batch barcode by inputting the command (e.g.
@DFMADD069990020010F141;) used to create a data format. See the “Use Batch Barcode” section in Chapter 9 to learn
how to put a batch barcode into use.
When creating multiple data formats sharing a label, the formats are separated from each other by a vertical bar (|) in the
batch command, e.g. @DFMADD069990029999F141|069990039999F142|169990049999F143;.
** Exit Setup 202

Enter Setup
Programming with Serial Commands
A data format can also be created by serial commands (HEX) sent from the host device. All commands must be entered
in uppercase letters.
The syntax consists of the following elements:
Prefix: “~<SOH>0000” (HEX: 7E 01 30 30 30 30), 6 characters.
Storage type: “@” (HEX: 40) or “#” (HEX: 23), 1 character. “@” means permanent setting which will not be lost by removing
power from the scanner or rebooting it; “#” means temporary setting which will be lost by removing power from the scanner
or rebooting it.
Add Data Format Command: “DFMADD” (HEX: 44 46 4D 41 44 44), 6 characters.
Data format label: “0” (HEX: 30) or “1” (HEX: 31) or “2” (HEX: 32) or ”3” (HEX: 33), 1 character. “0”, “1”, “2” and “3” represent
Format_0, Format_1, Format_2 and Format_3 respectively.
Formatter command type: “6” (HEX: 36), 1 character.
Interface type: “999” (HEX: 39 39 39), 3 characters.
Symbology ID Number: The ID number of the symbology to which you want to apply the data format, 3 characters. 999
indicates all symbologies.
Data length: The length of data that will be acceptable for this symbology, 4 characters. 9999 indicates all lengths. For
example, 32 characters should be entered as 0032.
Formatter commands: The command string used to edit data. For more information, see the “Formatter Command Type
6” section in this chapter.
Suffix: “;<ETX>” (HEX: 3B 03), 2 characters.
Example: Program a Format_0 data format using formatter command type 6, Code 128 containing 10 characters applicable,
send all characters followed by “A”.
Enter: 7E 01 30 30 30 30 40 44 46 4D 41 44 44 30 36 39 39 39 30 30 33 39 39 39 39 46 31 34 31 3B 03
(~<SOH>0000@DFMADD069990020010F141;<ETX>)
Response: 02 01 30 30 30 30 40 44 46 4D 41 44 44 30 36 39 39 39 30 30 33 39 39 39 39 46 31 34 31 06 3B 03
(<STX><SOH>0000@DFMADD069990020010F141<ACK>;<ETX>)
When creating multiple data formats sharing a label, the formats are separated from each other by a vertical bar (|) in the
serial command.
Example: ~<SOH>0000@DFMADD069990020010F141|069990039999F142|069990049999F143;<ETX>
203 ** Exit Setup

Enter Setup
Enable/Disable Data Formatter

When Data Formatter is disabled, the data format you have enabled becomes invalid.
** Disable Data Formatter
You may wish to require the data to conform to a data format you have created. The following settings can be applied to
your data format:
Enable Data Formatter, Required, Keep Prefix/Suffix: Scanned data that meets your data format requirements is
modified accordingly and gets outputted along with prefixes and suffixes (if prefix and suffix are enabled). Any data that
does not match your data format requirements generates an error beep (if Non-Match Error Beep is turned ON) and the
data in that barcode is not transmitted.
Enable Data Formatter, Required, Drop Prefix/Suffix: Scanned data that meets your data format requirements is modified
accordingly and gets outputted without prefixes and suffixes (even if prefix and suffix are enabled). Any data that does not
match your data format requirements generates an error beep (if Non-Match Error Beep is turned ON) and the data in that
barcode is not transmitted.
Enable Data Formatter, Not Required, Keep Prefix/Suffix: Scanned data that meets your data format requirements is
modified accordingly and gets outputted along with prefixes and suffixes (if prefix and suffix are enabled). Barcode data that
does not match your data format requirements is transmitted as read along with prefixes and suffixes (if prefix and suffix are
enabled).
Enable Data Formatter, Not Required, Drop Prefix/Suffix: Scanned data that meets your data format requirements is
modified accordingly and gets outputted without prefixes and suffixes (even if prefix and suffix are enabled). Barcode data
that does not match your data format requirements is transmitted as read along with prefixes and suffixes (if prefix and suffix
are enabled).
** Exit Setup 204

Enter Setup
Enable Data Formatter, Required, Keep Prefix/Suffix
Enable Data Formatter, Required, Drop Prefix/Suffix
Enable Data Formatter, Not Required, Keep Prefix/Suffix
Enable Data Formatter, Not Required, Drop Prefix/Suffix
Non-Match Error Beep

If Non-Match Error Beep is turned ON, the scanner generates an error beep when a barcode is encountered that does not
match your required data format.
Non-Match Error Beep Off
** Non-Match Error Beep On
205 ** Exit Setup

Enter Setup
Data Format Selection

After enabling the Data Formatter, you can select a data format you want to use by scanning the appropriate barcode below.
** Format_0
Format_1
Format_2
Format_3
** Exit Setup 206

Enter Setup
Change Data Format for a Single Scan

You can switch between data formats for a single scan. The next barcode is scanned using the data format selected here,
then reverts to the format you have selected above.
For example, you may have set your scanner to use the data format you saved as Format_3. You can switch to Format_1
for a single trigger pull by scanning the Single Scan – Format_1 barcode below. The next barcode that is scanned uses
Format_1, then reverts back to Format_3.
Note: This setting will be lost by removing power from the scanner, or turning off/ rebooting the device.
Single Scan – Format_0
207 ** Exit Setup

Enter Setup
Clear Data Format

There are two methods to remove data format created from your scanner:
Delete one data format: Scan the Clear One barcode, a numeric barcode (0-3) and the Save barcode. For example, to
delete Format_2, you should scan the Clear One barcode, the 2 barcode and the Save barcode
Delete all data formats: Scan the Clear All barcode.
Clear All
Clear One
Query Data Formats

You may scan the appropriate barcode below to get the information of data format(s) created by you or preset by
manufacturer. For instance, if you have added Format_0 as per the example in the “Add a Data Format” section in this
chapter, scanning the Query Current Data Formats barcode, you will get the result: Data Format0:069990020010F141;.
Query Current Data Formats
Query Preset Data Formats
** Exit Setup 208

Enter Setup
Formatter Command Type 6

When working with the Data Formatter, a virtual cursor is moved along your input data string. The following commands are
used to both move this cursor to different positions, and to select, replace, and insert data into the final output. For the hex
value of ASCII characters involved in the commands, refer to the “ASCII Table” in Appendix.
Send Commands
F1 Send all characters
Syntax=F1xx (xx: The insert character’s hex value)

Include in the output message all of the characters from the input message, starting from current cursor position, followed
by an insert character.
F2 Send a number of characters
Syntax=F2nnxx (nn: The numeric value (00-99) for the number of characters; xx: The insert character’s hex value)
Include in the output message a number of characters followed by an insert character. Start from the current cursor position
and continue for “nn” characters or through the last character in the input message, followed by character “xx.”
F2 Example: Send a number of characters
Send the first 10 characters from the barcode above, followed by a carriage return.
Command string: F2100D
F2 is the “Send a number of characters” command
10 is the number of characters to send
0D is the hex value for a CR
The data is output as: 1234567890

<CR>
209 ** Exit Setup

Enter Setup
F3 Send all characters up to a particular character
Syntax=F3ssxx (ss: The particular character’s hex value; xx: The insert character’s hex value)
Include in the output message all characters from the input message, starting with the character at the current cursor position
and continuing to, but not including, the particular character “ss,” followed by character “xx.” The cursor is moved forward
to the “ss” character.
F3 Example: Send all characters up to a particular character
Using the barcode above, send all characters up to but not including “D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
44 is the hex value for a “D”
The data is output as: 1234567890ABC

<CR>
** Exit Setup 210

Enter Setup
B9 Send all characters up to a particular string
Syntax=B9nnnns...s (nnnn: The length of the particular string; s...s: The hex value of each character in the particular string)
Include in the output message all characters from the input message, starting with the character at the current cursor position
and continuing to, but not including, the particular string “s...s.” The cursor is moved forward to the beginning of the “s...s”
string.
B9 Example: Send all characters up to a particular string
Using the barcode above, send all characters up to but not including “AB.”
Command string: B900024142
B9 is the “Send all characters up to a particular string” command
0002 is the length of the particular string (2 characters)
41 is the hex value for a “A” (character in the string)
42 is the hex value for a “B” (character in the string)
E9 Send all but the last characters
Syntax=E9nn (nn: The numeric value (00-99) for the number of characters that will not be sent at the end of the message)
Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved
forward to one position past the last input message character included.
F4 Insert a character multiple times
Syntax=F4xxnn (xx: The insert character’s hex value; nn: The numeric value (00-99) for the number of times it should be
sent)
Send “xx” character “nn” times in the output message, leaving the cursor in the current position.
211 ** Exit Setup

Enter Setup
E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the barcode above, followed by 2 tabs.
Command string: E908F40902
E9 is the “Send all but the last characters” command
08 is the number of characters at the end to ignore
F4 is the “Insert a character multiple times” command
09 is the hex value for a horizontal tab
02 is the number of times the tab character is sent
The data is output as: 1234567890AB<tab><tab>
B3 Insert symbology name
Insert the name of the barcode’s symbology in the output message, without moving the cursor.
B4 Insert barcode length
Insert the barcode’s length in the output message, without moving the cursor. The length is expressed as a numeric string
and does not include leading zeros.
** Exit Setup 212

Enter Setup
B3 and B4 Example: Insert the symbology name and length
Send the symbology name and length before the barcode data from the barcode above. Break up these insertions with
spaces. End with a carriage return.
Command string: B3F42001B4F42001F10D
B3 is the “Insert symbology name” command
20 is the hex value for a space
01 is the number of times the space character is sent
B4 is the “Insert barcode length” command
01 is the number of times the space character is sent
F1 is the “Send all characters” command
The data is output as: Code128 20 1234567890ABCDEFGHIJ

<CR>
Move Commands
F5 Move the cursor forward a number of characters
Syntax=F5nn (nn: The numeric value (00-99) for the number of characters the cursor should be moved ahead)
Move the cursor ahead “nn” characters from current cursor position.
213 ** Exit Setup

Enter Setup
F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above. End with a carriage
return.
Command string: F503F10D
F5 is the “Move the cursor forward a number of characters” command
03 is the number of characters to move the cursor
The data is output as: 4567890ABCDEFGHIJ

<CR>
F6 Move the cursor backward a number of characters
Syntax=F6nn (nn: The numeric value (00-99) for the number of characters the cursor should be moved back)
Move the cursor back “nn” characters from current cursor position.
F7 Move the cursor to the beginning
Syntax＝F7
Move the cursor to the first character in the input message.
EA Move the cursor to the end
Syntax＝EA
Move the cursor to the last character in the input message.
** Exit Setup 214

Enter Setup
Search Commands
F8 Search forward for a character
Syntax＝F8xx (xx: The search character’s hex value)
Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx”
character.
F8 Example: Send barcode data that starts after a particular character
Search for the letter “D” in barcodes and send all the data that follows, including the “D”. Using the barcode above:
Command string: F844F10D
F8 is the “Search forward for a character” command
44 is the hex value for “D”
The data is output as: DEFGHIJ
<CR>
F9 Search backward for a character
Syntax＝F9xx(xx: The search character’s hex value)
Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the
“xx” character.
215 ** Exit Setup

Enter Setup
B0 Search forward for a string
Syntax=B0nnnnS (nnnn: The string length (up to 9999); S: The ASCII hex value of each character in the string)
Search forward for “S” string from the current cursor position, leaving cursor pointing to “S” string. For example,
B0000454657374 will search forward for the first occurrence of the 4-character string “Test.”
B0 Example: Send barcode data that starts after a string of characters
Search for the letters “FGH” in barcodes and send all the data that follows, including “FGH.” Using the barcode above:
Command string: B00003464748F10D
B0 is the “Search forward for a string” command
0003 is the string length (3 characters)
46 is the hex value for “F”
47 is the hex value for “G”
48 is the hex value for “H”
The data is output as: FGHIJ

<CR>
B1 Search backward for a string
Syntax＝B1nnnnS (nnnn: The string length (up to 9999); S: The ASCII hex value of each character in the string)
Search backward for “S” string from the current cursor position, leaving cursor pointing to “S” string. For example,
B1000454657374 will search backward for the first occurrence of the 4-character string “Test.”
** Exit Setup 216

Enter Setup
E6 Search forward for a non-matching character
Syntax=E6xx (xx: The search character’s hex value)
Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor pointing
to the non-“xx” character.
E6 Example: Remove zeros at the beginning of barcode data
This example shows a barcode that has been zero filled. You may want to ignore the zeros and send all the data that follows.
E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage return. Using
the barcode above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
The data is output as: 123abc
<CR>
E7 Search backward for a non-matching character
Syntax＝E7xx(xx: The search character’s hex value)
Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor
pointing to the non-“xx” character.
217 ** Exit Setup

Enter Setup
Miscellaneous Commands
FB Suppress characters
Syntax＝FBnnxxyy..zz (nn: The numeric value (00-15) for the number of suppressed characters; xxyy..zz: The hex value of
the characters to be suppressed)
Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced
by other commands.
FB Example: Remove spaces in barcode data
This example shows a barcode that has spaces in the data. You may want to remove the spaces before sending the data.
Using the barcode above:
Command string: FB0120F10D
FB is the “Suppress characters” command
01 is the number of the characters to be suppressed
The data is output as: 1234_5*678
<CR>
E4 Replace characters
Syntax＝ E4nnxx1xx2yy1yy2…zz1zz2(nn: The total count of the number of characters (characters to be replaced plus
replacement characters; xx1: The characters to be replaced, xx2: The replacement characters, continuing through zz1 and
zz2)
Replace up to 15 characters in the output message, without moving the cursor.
** Exit Setup 218

Enter Setup
E4 Example: Replace zeros with CRs in barcode data
If the barcode has characters that the host application does not want included, you can use the E4 command to replace
those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total characters=2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)

456
78
AB
<CR>
219 ** Exit Setup

Enter Setup
BA Replace a string with another
Syntax＝BAnnNN1SS1NN2SS2
nn: The count of replacements to be made, if nn=00 or nn>=the number of occurrences of a string to be replaced, then
replace all occurrences of that string.
NN1: The length of the string to be replaced, NN1>0.
SS1: The ASCII hex value of each character in the string to be replaced.
NN2: The length of replacement string, NN2>=0. To replace string “SS1” with NUL (i.e. deIete string “SS1”), you should set
NN2 to 00 and leave out SS2.
SS2: The ASCII hex value of each character in the replacement string.
From the current cursor position, search forward for the occurrence of “SS1” string (of length “NN1”) and replace the string
with “SS2” string (of length “NN2”) in the output message until every “SS1” stringis replaced or the count of replacements
made reaches “nn” times, without moving the cursor.
BA Example: Replace “23”s with “ABC”s in barcode data
If the barcode has a string of characters that the host application does not want included, you can use the BA command to
replace the string with something else. In this example, you will replace the “23”s in the barcode above with “ABC”s.
Command string: BA0002323303414243F100
BA is the “Replace a string with another” command
00 is the count of replacements to be made, 00 means to replace all occurrences of that string
02 is the length of the string to be replaced
32 is the hex value for 2 (character in the string to be replaced)
03 is the length of the replacement string
** Exit Setup 220

Enter Setup
41 is the hex value for A (character in the replacement string)
42 is the hex value for B (character in the replacement string)
43 is the hex value for C (character in the replacement string)
00 is the hex value for a NUL
The data is output as: 1ABC4AbcABCR01ABCU
BA Example: Remove only the first occurrence of “23”s in barcode data
If the barcode has a string of characters that the host application wants removed, you can use the BA command to replace
the string with NUL. In this example, you will remove the first occurrence of “23” in the barcode above.
Command string: BA0102323300F100
BA is the “Replace a string with another” command
01 is the count of replacements to be made
02 is the length of the string to be replaced
00 is the length of the replacement string, 00 means to replace the string to be replaced with NUL
00 is the hex value for a NUL
The data is output as: 14Abc23R0123U
221 ** Exit Setup

Enter Setup
EF Insert a delay
Syntax＝EFnnnn (nnnn: The delay in 5ms increments, up to 9999)
Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. This command can
only be used with USB HID Keyboard.
EF Example: Insert a delay of 1s between the 5th and 6th character
Send the first 5 characters in a barcode, wait for 1s, then send the rest of the barcode data.
Command string: F20500EF0200E900
F2 is the “Send a number of characters” command
05 is the number of characters to send
00 is the hex value for a Null character
EF is the “Insert a delay” command
0200 is the delay value (5msX200=1000ms=1s)
E9 is the “Send all but the last characters” command
00 is the number of characters that will not be sent at the end of the message
** Exit Setup 222

Enter Setup
B5 Insert key strokes
Syntax=B5nnssxx (nn: The number of keys pressed (without key modifiers); ss: the key modifier from the table below; xx:
the key number from the “Unicode Key Maps” in Appendix.)
Insert a key stroke or combination of key strokes. Key strokes are dependent on your keyboard (see the “Unicode Key Maps”
in Appendix). This command can only be used with USB HID Keyboard.
Key Modifiers
No Key Modifier 00
Shift Left 01
Shift Right 02
Alt Left 04
Alt Right 08
Control Left 10
Control Right 20
For example, B501001F inserts an “a” on a U.S. style keyboard. B5 = the command, 01 = number of keys pressed (without
the key modifier), 00 is No Key Modifier, and 1F is the “a” key. If an “A” were to be inserted, B501011F or B501021F would
be entered.
If there are two keystrokes, the syntax would change from Syntax=B5nnssxx for one keystroke to Syntax=B5nnssxxssxx.
An example that would insert “aA” is as follows: B502001F011F.
Note: Key modifiers can be added together when needed. Example: Shift Left + Alt Left + Control Left =15.
223 ** Exit Setup

Enter Setup
Chapter 8 Prefix & Suffix
Introduction
A 1D barcode could contain digits, letters, symbols, etc. A 2D barcode could contain more data, such as Chinese characters
and other multi-byte characters. However, in real applications, they do not and should not have all information we need,
such as barcode type, data acquisition time and delimiter, in order to keep the barcodes short and flexible.
Preffix and suffix are how to fulfill the needs mentioned above. They can be added, removed and modified while the original
barcode data remains intact.
Barcode processing procedure:
1. Edit data with Data Formatter
2. Append prefix/suffix
3. Pack data
4. Append terminating character
** Exit Setup 224

Enter Setup
Global Settings
Enable/Disable All Prefixes/Suffixes
Disable All Prefixes/Suffixes: Transmit barcode data with no prefix/suffix.
Enable All Prefixes/Suffixes: Allow to append Code ID prefix, AIM ID prefix, custom prefix/suffix and terminating character
to the barcode data before the transmission.
** Disable All Prefixes/Suffixes
Enable All Prefixes/Suffixes
Prefix Sequence
** Code ID+ Custom +AIM ID
Custom + Code ID + AIM ID
225 ** Exit Setup

Enter Setup
Custom Prefix
Enable/Disable Custom Prefix
If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot exceed 10 characters.
For example, if the custom prefix is “AB” and the barcode data is “123”, the Host will receive “AB123”.
** Disable Custom Prefix
Enable Custom Prefix
Set Custom Prefix
To set a custom prefix, scan the Set Custom Prefix barcode then the numeric barcodes corresponding to the hexadecimal
value of a desired prefix then the Save barcode.
Note: A custom prefix cannot exceed 10 characters.
Set Custom Prefix
Set the custom prefix to “CODE” (HEX: 0x43/0x4F/0x44/0x45):
2. Scan the Set Custom Prefix barcode.
3. Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes” section in
Appendix.
5. Scan the Enable Custom Prefix barcode.
** Exit Setup 226

Enter Setup
AIM ID Prefix
AIM (Automatic Identification Manufacturers) ID defines symbology identifier (For the details, see the “AIM ID Table”
section in Appendix). If AIM ID prefix is enabled, the scanner will add the symbology identifier before the scanned data
after decoding.
** Disable AIM ID Prefix
Enable AIM ID Prefix
AIM ID is not user programmable.
227 ** Exit Setup

Enter Setup
Code ID Prefix
Code ID can also be used to identify barcode type. Unlike AIM ID, Code ID is user programmable. Code ID can only consist
of one or two English letters.
** Disable Code ID Prefix
Enable Code ID Prefix
Restore All Default Code IDs
For the information of default Code IDs, see the “Code ID Table” section in Appendix.
Restore All Default Code IDs
Modify Code ID
See the examples below to learn how to modify a Code ID and restore the default Code IDs of all symbologies.
** Exit Setup 228

Enter Setup
Modify PDF417 Code ID to be “p” (HEX: 0x70):
2. Scan the Modify PDF417 Code ID barcode.
Restore the default Code IDs of all symbologies:
2. Scan the Restore All Default Code IDs barcode.
229 ** Exit Setup

Enter Setup
1D symbologies:
Modify Code 128 Code ID
Modify GS1-128 Code ID
Modify EAN-8 Code ID
Modify EAN-13 Code ID
Modify UPC-E Code ID
Modify UPC-A Code ID
Modify Interleaved 2 of 5 Code ID
** Exit Setup 230

Enter Setup
Modify ITF-14 Code ID
Modify ITF-6 Code ID
Modify Matrix 2 of 5 Code ID
Modify Codabar Code ID
Modify China Post 25 Code ID
Modify AIM 128 Code ID
231 ** Exit Setup

Enter Setup
Modify ISBT 128 Code ID
Modify ISSN Code ID
Modify ISBN Code ID
Modify Industrial 25 Code ID
Modify Standard 25 Code ID
Modify Plessey Code ID
Modify MSI-Plessy Code ID
** Exit Setup 232

Enter Setup
Modify GS1 Composite Code ID
Modify GS1 Databar Code ID
Modify Code 16K Code ID
233 ** Exit Setup

Enter Setup
2D symbologies:
Modify PDF417 Code ID
Modify QR Code ID
Modify Aztec Code ID
Modify Data Matrix Code ID
Modify Maxicode Code ID
Modify Chinese Sensible Code ID
Modify GM Code ID
** Exit Setup 234

Enter Setup
Modify Micro PDF417 Code ID
Modify Micro QR Code ID
Modify Code One Code ID
235 ** Exit Setup

Enter Setup
Postal symbologies:
Modify USPS Postnet Code ID
Modify USPS Inteligent Mail Code ID
Modify Royal Mail Code ID
Modify USPS Planet Code ID
Modify KIX Post Code ID
Modify Australian Postal Code ID
** Exit Setup 236

Enter Setup
Custom Suffix
Enable/Disable Custom Suffix
If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed 10 characters.
For example, if the custom suffix is “AB” and the barcode data is “123”, the Host will receive “123AB”.
** Disable Custom Suffix
Enable Custom Suffix
Set Custom Suffix
To set a custom suffix, scan the Set Custom Suffix barcode then the numeric barcodes corresponding to the hexadecimal
value of a desired suffix then the Save barcode.
Note: A custom suffix cannot exceed 10 characters.
Set Custom Suffix
Set the custom suffix to “CODE” (HEX: 0x43/0x4F/0x44/0x45):

2. Scan the Set Custom Suffix barcode.
3. Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes” section in
Appendix.
5. Scan the Enable Custom Suffix barcode.
237 ** Exit Setup

Enter Setup
Data Packing
Introduction
Data packing is designed for a specific group of users who want to have the data packed before transmission. Data packing
influences data format, so it is advised to disable this feature when it is not required.
Data Packing Options
Disable Data Packing: Transmit decoded data in raw format (unpacketed).
Enable Data Packing, Format 1: Transmit decoded data with the packet format 1 defined below.
Packet format 1: [STX + ATTR + LEN] + [AL_TYPE + DATA] + [LRC]
STX: 0x02
ATTR: 0x00
LEN: Barcode data length is expressed in 2 bytes ranging from 0x0000 (0) to 0xFFFF (65535).
AL_TYPE: 0x36
DATA: Raw barcode data.
LRC: Check digit.

LRC calculation algorithm: computation sequence: 0xFF+LEN+AL_TYPE+DATA; computation method is XOR, byte
by byte.
Enable Data Packing, Format 2: Transmit decoded data with the packet format 2 defined below.
Packet format 2: [STX + ATTR + LEN] + [AL_TYPE] + [Symbology_ID + DATA] + [LRC]
STX: 0x02
ATTR: 0x00
LEN: Barcode data length is expressed in 2 bytes ranging from 0x0000 (0) to 0xFFFF (65535).
AL_TYPE: 0x3B
Symbology_ID: The ID number of symbology, 1 byte.
DATA: Raw barcode data.
LRC: Check digit.

LRC calculation algorithm: computation sequence: 0xFF+LEN+AL_TYPE+Symbology_ID+DATA; computation
method is XOR, byte by byte.
** Exit Setup 238

Enter Setup
** Disable Data Packing
Enable Data Packing, Format 1
Enable Data Packing, Format 2
239 ** Exit Setup

Enter Setup
Terminating Character Suffix

Enable/Disable Terminating Character Suffix
A terminating character such as carriage return (CR) or carriage return/line feed pair (CRLF) can only be used to mark the
end of data, which means nothing can be added after it.
Disable Terminating Character Suffix
** Enable Terminating Character Suffix
Set Terminating Character Suffix
To set a terminating character suffix, scan the Set Terminating Character Suffix barcode then the numeric barcodes
corresponding to the hexadecimal value of a desired terminating character then the Save barcode.
Note: A terminating character suffix cannot exceed 2 characters.
Set Terminating Character Suffix
Set Terminating Character to CR (0x0D)
** Set Terminating Character to CRLF (0x0D,0x0A)
** Exit Setup 240

Enter Setup
Set the terminating character suffix to 0x0A:
2. Scan the Set Terminating Character Suffix barcode.
3. Scan the numeric barcodes “0” and “A” from the “Digit Barcodes” section in Appendix.
5. Scan the Enable Terminating Character Suffix barcode.
241 ** Exit Setup

Enter Setup
Chapter 9 Batch Programming
Introduction
Batch programming enables users to integrate a batch of commands into a single batch barcode.
Listed below are batch programming rules:
1. Command format: Command + Parameter Value.
2. Each command is terminated by a semicolon (;). Note that there is no space between a command and its terminator
semicolon.
3. Use the barcode generator software to generate a 2D batch barcode.
Example: Create a batch barcode for Illumination Always On, Sense Mode, Decode Session Timeout = 2s:
1. Input the commands:
@ILLSCN2;SCNMOD2;ORTSET2000;
2. Generate a batch barcode.
When setting up the scanner with the above configuration, scan the Enable Batch Barcode barcode and then the batch
barcode generated.
Enable Batch Barcode
** Exit Setup 242

Enter Setup
Create a Batch Command

A batch command may contain a number of individual commands each of which is terminated by a semicolon (;).
For more information, refer to the “Use of Programming Command” section in Chapter 3.
Create a Batch Barcode

Batch barcodes can be produced in the format of PDF417, QR Code or Data Matrix.
Example: Create a batch barcode for lllumination Always On, Sense Mode, Decode Session Timeout = 2s:
1. Input the following commands:
@ILLSCN2;SCNMOD2;ORTSET2000;
2. Generate a PDF417 batch barcode.
243 ** Exit Setup

Enter Setup
Use Batch Barcode

To put a batch barcode into use, scan the following barcodes. (Use the example above.)
Enter Setup
Enable Batch Barcode
Batch Barcode
Exit Setup
** Exit Setup 244

Appendix
Digit Barcodes
0~9
245
6
246
A~F
247
Save/Cancel Barcodes
After reading numeric barcode(s), you need to scan the Save barcode to save the data. If you scan the wrong digit(s), you
can either scan the Cancel barcode and then start the configuration all over again, or scan the Delete the Last Digit
barcode and then the correct digit, or scan the Delete All Digits barcode and then the digits you want.
For instance, after reading the Maximum Length barcode and numeric barcodes “1”, “2” and “3”, you scan:
 Delete the Last Digit: The last digit “3” will be removed.
 Delete All Digits: All digits “123” will be removed.
 Cancel: The maximum length configuration will be cancelled. And the scanner is still in the setup mode.
Save
Cancel
Delete the Last Digit
Delete All Digits
248
Factory Defaults Table
Parameter Factory Default Remark

System Settings
Barcode Programming Disabled (Exit Setup)
Programming Barcode Data Do not transmit
Illumination Normal
Illumination LED Selection White LED
Good Read LED On
Good Read LED Duration Long (220ms)
Good Read LED Selection Green LED
Power On Beep On
Good Read Beep On
Good Read Beep Duration Medium (80ms)
Good Read Beep Frequency Medium (2730Hz)
Good Read Beep Volume Loud
Scan Mode Sense Mode
Decode Session Timeout 5,000ms. 1-3,600,000ms; 0: Infinite
Image Stabilization Timeout (Sense Mode) 100ms 0-3,000ms
Disabled
Reread Timeout
1,500ms 1-3,600,000ms
Reread Timeout Reset Off
Image Decoding Timeout 500ms 1-3,000ms
Trigger Selection (Sense Mode) Both
Image Change Trigger Sensitivity Medium
IR Proximity Trigger Sensitivity Level 1
Trigger Commands Disabled
Start Scanning Command <SOH> T <EOT>
Stop Scanning Command <SOH> P <EOT>
Scanning Preference Normal Mode
Read Barcode On/Off On
Decode Area Whole Area Decoding
Specify Decoding Area 40% top, 60% bottom, 40% left, 60% right
Image Flipping Do Not Flip
249
Off
Bad Read Message
NG 1-7 characters
Default Interface USB HID Keyboard
RS-232 Interface
Baud Rate 9600
Parity Check None
Data Bits 8
Stop Bits 1
Hardware Auto Flow Control Disabled
USB Interface
USB Country Keyboard US keyboard USB HID Keyboard
Beep on Unknown Character Off USB HID Keyboard
Emulate ALT+Keypad Off USB HID Keyboard
Code Page Code Page 1252 (West European Latin) USB HID Keyboard
Unicode Encoding Off USB HID Keyboard
Emulate Keypad with Leading Zero On USB HID Keyboard
Function Key Mapping Disable USB HID Keyboard
Inter-Keystroke Delay No Delay USB HID Keyboard
Caps Lock Caps Lock OFF, non-Japanese Keyboard USB HID Keyboard
Convert Case No Case Conversion USB HID Keyboard
Emulate Numeric Keypad 1 Off USB HID Keyboard
Emulate Numeric Keypad 2 Off USB HID Keyboard
Fast Mode Off USB HID Keyboard
Polling Rate 1ms USB HID Keyboard
Symbologies
Global Settings
1D Twin Code Single 1D Code Only
Surround GS1 AI’s with Parentheses Do Not Surround GS1 AI’s with Parentheses
Code 128
Code 128 Enabled
Maximum Length 48
Minimum Length 1
EAN-8
EAN-8 Enabled
250
Check Character Transmit
2-Digit Add-On Code Disabled
Add-On Code Not Required
Convert EAN-8 to EAN-13 Disabled
EAN-13
EAN-13 Enabled
EAN-13 Beginning with 290 Add-On Code Required Do Not Require Add-On Code
EAN-13 Beginning with 378/379 Add-On Code

Do Not Require Add-On Code
Required
Required
Required
UPC-E
UPC-E0 Enabled
UPC-E1 Disabled
Transmit Preamble Character System Character
Convert UPC-E to UPC-A Disabled
UPC-A
UPC-A Enabled
251
Transmit Preamble Character No Preamble
Coupon
UPC-A/EAN-13 with Extended Coupon Code Disabled
Coupon GS1 DataBar Output Disabled
Interleaved 2 of 5
Interleaved 2 of 5 Enabled
Maximum Length 80
Minimum Length 6 No less than 4
Check Character Verification Disabled
ITF-14
ITF-14 Disabled
ITF-6
ITF-6 Disabled
Matrix 2 of 5
Matrix 2 of 5 Disabled
Maximum Length 80
Code 39
Code 39 Enabled
Maximum Length 48
Minimum Length 1
Start/Stop Character Do not transmit
Code 39 Full ASCII Disabled
Code 32 Pharmaceutical (PARAF) Disabled
Code 32 Prefix Disabled
Code 32 Start/Stop Character Do not transmit
Code 32 Check Character Do not transmit
Codabar
Codabar Enabled
Maximum Length 60
252
Minimum Length 2
Do not transmit
Start/Stop Character
ABCD/ABCD
Code 93
Code 93 Enabled
Maximum Length 48
Do Not Transmit Check Character After
Verification
China Post 25
China Post 25 Disabled
Maximum Length 48
Minimum Length 1
GS1-128 (UCC/EAN-128)
GS1-128 Enabled
Maximum Length 48
Minimum Length 1
GS1 Databar
GS1 Databar Enabled
Application Identifier “01” Transmit
EAN•UCC Composite
GS1 Composite Enabled
UPC/EAN Composite Disabled
Code 11
Code 11 Enabled
Maximum Length 48
Check Character Verification One Check Character, MOD11
Check Character Do not transmit
ISBN
ISBN Enabled
Set ISBN Format ISBN-10
253
ISSN
ISSN Disabled
Industrial 25
Industrial 25 Enabled
Maximum Length 48
Standard 25
Standard 25 Disabled
Maximum Length 48
Plessey
Plessey Enabled
Maximum Length 48
MSI-Plessey
MSI-Plessey Enabled
Maximum Length 48
Check Character Verification One Check Character, MOD10
AIM 128
AIM 128 Enabled
Maximum Length 48
Minimum Length 1
ISBT 128
ISBT 128 Disabled
Code 49
Code 49 Disabled
Maximum Length 80
Minimum Length 1
Code 16K
254
Code 16K Disabled
Maximum Length 80
Minimum Length 1
PDF417
PDF417 Enabled
Maximum Length 2710
Minimum Length 1
PDF417 Twin Code Single PDF417 Only
PDF417 Inverse Decode Regular PDF417 Barcodes Only
Character Encoding Default Character Encoding
PDF417 ECI Output Enabled
Micro PDF417
Micro PDF417 Disabled
Maximum Length 366
Minimum Length 1
QR Code
QR Code Enabled
Maximum Length 7089
Minimum Length 1
QR Twin Code Single QR Only
QR Inverse Decode Regular QR Barcodes Only
QR ECI Output Enabled
Micro QR Code
Micro QR Disabled
Maximum Length 35
Minimum Length 1
Aztec
Aztec Code Disabled
Maximum Length 3832
Minimum Length 1
Read Multi-barcodes on an Image Mode 1
Aztec ECI Output Enabled
255
Data Matrix
Data Matrix Enabled
Maximum Length 3116
Minimum Length 1
Data Matrix Twin Code Single Data Matrix Only
Rectangular Barcode Enabled
Data Matrix Inverse Decode Regular Data Matrix Barcodes Only
Data Matrix ECI Output Enabled
Maxicode
Maxicode Disabled
Maximum Length 150
Minimum Length 1
Chinese Sensible Code
Chinese Sensible Code Disabled
Maximum Length 7827
Minimum Length 1
Chinese Sensible Twin Code Single Chinese Sensible Code Only
Chinese Sensible Code Inverse Decode Regular Chinese Sensible
Barcodes Only
GM Code
GM Disabled
Maximum Length 2571
Minimum Length 1
Code One
Code One Disabled
Maximum Length 3550
Minimum Length 1
USPS Postnet
USPS Postnet Disabled
USPS Intelligent Mail
USPS Intelligent Mail Disabled
Royal Mail
256
Royal Mail Disabled
USPS Planet
USPS Planet Disabled
KIX Post
KIX Post Disabled
Australian Postal
Australian Postal Disabled
Specific OCR-B
Specific OCR-B Disabled
Passport OCR
Passport OCR Disabled
Data Formatter
Data Formatter Disabled
Non-Match Error Beep On
Data Format Selection Format_0
Prefix & Suffix
All Prefixes/Suffixes Disabled
Prefix Sequence Code ID+ Custom +AIM ID
Custom Prefix Disabled
AIM ID Prefix Disabled
Code ID Prefix Disabled
Custom Suffix Disabled
Data Packing Disable Data Packing
Enabled
Terminating Character Suffix
0x0D, 0x0A (Carriage Return/Line Feed)
257
AIM ID Table
Symbology AIM ID Possible AIM ID Modifiers (m)
Code 128 ]C0
GS1-128 (UCC/EAN-128) ]C1
EAN-8 ]E4
EAN-8 with Addon ]E3
EAN-13 ]E0
EAN-13 with Addon ]E3
UPC-E ]E0
UPC-E with Addon ]E3
UPC-A ]E0
UPC-A with Addon ]E3
Interleaved 2 of 5 ]Im 0, 1, 3
ITF-14 ]Im 1, 3
ITF-6 ]Im 1, 3
Matrix 2 of 5 ]X0
Code 39 ]Am 0, 1, 3, 4, 5, 7
Codabar ]Fm 0, 2, 4
Code 93 ]G0
China Post 25 ]X0
AIM 128 ]C2
ISBT 128 ]C4
ISSN ]X0
ISBN ]X0
Industrial 25 ]S0
Standard 25 ]R0
Plessey ]P0
Code 11 ]Hm 0, 1, 3
MSI Plessey ]Mm 0, 1
GS1 Composite ]em 0-3
GS1 Databar (RSS) ]e0
Code 49 ]T0
Code 16K ]K0
258
Symbology AIM ID Possible AIM ID Modifiers (m)
PDF417 ]Lm 0-2
QR Code ]Qm 0-6
Aztec ]zm 0-9, A-C
Data Matrix ]dm 0-6
Maxicode ]Um 0-3
Chinese Sensible Code ]X0
GM ]gm (0~9)
Micro PDF417 ]L0
Micro QR ]Q1
Code One ]X0
USPS Postnet ]X0
USPS Inteligent Mail ]X0
Royal Mail ]X0
USPS Planet ]X0
KIX Post ]X0
Australian Postal ]X0
Specific OCR-B ]o2
Passport OCR ]o2
Note: “m” represents the AIM modifier character. Refer to ISO/IEC 15424:2008 Information technology – Automatic identification
and data capture techniques – Data Carrier Identifiers (including Symbology Identifiers) for AIM modifier character details.
259
Code ID Table
Symbology Code ID
Code 128 j
GS1-128 (UCC/EAN-128) j
EAN-8 d
EAN-13 d
UPC-E c
UPC-A c
Interleaved 2 of 5 e
ITF-14 e
ITF-6 e
Matrix 2 of 5 v
Code 39 b
Codabar a
Code 93 i
China Post 25 X
AIM 128 X
ISBT 128 X
ISSN g
ISBN B
Industrial 25 I
Standard 25 f
Plessey n
Code 11 H
MSI Plessey m
GS1 Composite y
GS1 Databar (RSS) R
Code 49 X
Code 16K X
PDF417 r
QR Code s
Aztec z
Data Matrix u
260
Symbology Code ID
MaxiCode x
Chinese Sensible Code h
GM Code x
Micro PDF417 R
Micro QR X
Code One X
USPS Postnet P
USPS Inteligent Mail M
Royal Mail x
USPS Planet L
KIX Post K
Australian Postal A
Specific OCR-B S
Passport OCR O
261
Symbology ID Number
Symbology ID Number
Code 128 002
GS1-128 (UCC/EAN-128) 003
EAN-8 004
EAN-13 005
UPC-E 006
UPC-A 007
Interleaved 2 of 5 008
ITF-14 009
ITF-6 010
Matrix 2 of 5 011
Code 39 013
Codabar 015
Code 93 017
China Post 25 019
AIM 128 020
ISBT 128 021
ISSN 023
ISBN 024
Industrial25 025
Standard25 026
Plessey 027
Code11 028
MSI-Plessey 029
GS1 Composite 030
GS1 Databar (RSS) 031
PDF417 032
QR Code 033
Aztec 034
Data Matrix 035
Maxicode 036
Chinese Sensible Code 039
262
Symbology ID Number
GM Code 040
Micro PDF417 042
Micro QR 043
Code One 048
Specific OCR-B 064
Passport OCR 066
USPS Postnet 096
USPS Inteligent Mail 097
Royal Mail 098
USPS Planet 099
KIX Post 100
Australian Postal 101
263
ASCII Table
Hex Dec Char
00 0 NUL (Null char.)
01 1 SOH (Start of Header)
02 2 STX (Start of Text)
03 3 ETX (End of Text)
04 4 EOT (End of Transmission)
05 5 ENQ (Enquiry)
06 6 ACK (Acknowledgment)
07 7 BEL (Bell)
08 8 BS (Backspace)
09 9 HT (Horizontal Tab)
0a 10 LF (Line Feed)
0b 11 VT (Vertical Tab)
0c 12 FF (Form Feed)
0d 13 CR (Carriage Return)
0e 14 SO (Shift Out)
0f 15 SI (Shift In)
10 16 DLE (Data Link Escape)
11 17 DC1 (XON) (Device Control 1)
12 18 DC2 (Device Control 2)
13 19 DC3 (XOFF) (Device Control 3)
14 20 DC4 (Device Control 4)
15 21 NAK (Negative Acknowledgment)
16 22 SYN (Synchronous Idle)
17 23 ETB (End of Trans. Block)
18 24 CAN (Cancel)
19 25 EM (End of Medium)
1a 26 SUB (Substitute)
1b 27 ESC (Escape)
1c 28 FS (File Separator)
1d 29 GS (Group Separator)
264
Hex Dec Char
1e 30 RS (Request to Send)
1f 31 US (Unit Separator)
20 32 SP (Space)
21 33 ! (Exclamation Mark)
22 34 " (Double Quote)
23 35 # (Number Sign)
24 36 $ (Dollar Sign)
25 37 % (Percent)
26 38 & (Ampersand)
27 39 ` (Single Quote)
28 40 ( (Left/ Opening Parenthesis)
29 41 ) (Right/ Closing Parenthesis)
2a 42 * (Asterisk)
2b 43 + (Plus)
2c 44 , (Comma)
2d 45 - (Minus/ Dash)
2e 46 . (Dot)
2f 47 / (Forward Slash)
30 48 0
31 49 1
32 50 2
33 51 3
34 52 4
35 53 5
36 54 6
37 55 7
38 56 8
39 57 9
3a 58 : (Colon)
3b 59 ; (Semi-colon)
3c 60 < (Less Than)
3d 61 = (Equal Sign)
265
Hex Dec Char
3e 62 > (Greater Than)
3f 63 ? (Question Mark)
40 64 @ (AT Symbol)
41 65 A
42 66 B
43 67 C
44 68 D
45 69 E
46 70 F
47 71 G
48 72 H
49 73 I
4a 74 J
4b 75 K
4c 76 L
4d 77 M
4e 78 N
4f 79 O
50 80 P
51 81 Q
52 82 R
53 83 S
54 84 T
55 85 U
56 86 V
57 87 W
58 88 X
59 89 Y
5a 90 Z
5b 91 [ (Left/ Opening Bracket)
5c 92 \ (Back Slash)
5d 93 ] (Right/ Closing Bracket)
266
Hex Dec Char
5e 94 ^ (Caret/ Circumﬂex)
5f 95 _ (Underscore)
60 96 ' (Grave Accent)
61 97 a
62 98 b
63 99 c
64 100 d
65 101 e
66 102 f
67 103 g
68 104 h
69 105 i
6a 106 j
6b 107 k
6c 108 l
6d 109 m
6e 110 n
6f 111 o
70 112 p
71 113 q
72 114 r
73 115 s
74 116 t
75 117 u
76 118 v
77 119 w
78 120 x
79 121 y
7a 122 z
7b 123 { (Left/ Opening Brace)
7c 124 | (Vertical Bar)
7d 125 } (Right/ Closing Brace)
7e 126 ~ (Tilde)
7f 127 DEL (Delete)
267
Unicode Key Maps
104 Key U.S. Style Keyboard
105 Key European Style Keyboard
268
SCANNING MADE SIMPLE
Newland EMEA HQ D-A-CH United Kingdom France Russia

+31 (0) 345 87 00 33 +49 (0) 6182 82916-16 +44 (0) 1442 212020 +39 (0) 345 8804096 +7 (495) 120 23 85
info@newland-id.com info@newland-id.de sales@newland-id.co.uk france@newland-id.com russia@newland-id.com
newland-id.com
Benelux South Africa Ibérica Middle East

+31 (0) 345 87 00 33 Gauteng: +27 (0) 11 553 8010 +31 (0) 345 87 00 33 +39 (0) 345 8804096
benelux@newland-id.com Cape Town: +27 (0) 21 9140819 info@newland-id.com middleeast@newland-id.com
info@newland-id.co.za
Italy Turkey Nordic & Baltic Iran
+39 (0) 342 0562227 +90 (0) 544 538 40 49 +46 (0) 70 88 47 767 +90 (0) 544 538 40 49
italy@newland-id.com turkey@newland-id.com nordic@newland-id.com iran@newland-id.com

FM 3080 Hind: Fixed Mount Barcode Scanner

Uploaded by

Copyright:

Available Formats

FM 3080 Hind: Fixed Mount Barcode Scanner

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FM 3080 Hind: Fixed Mount Barcode Scanner

Uploaded by

Copyright:

Available Formats

SCANNING MADE SIMPLE

Fujian Newland Auto-ID Tech. Co., Ltd.

V1.0.0 Initial release. December 18, 2018

Chapter 1 Getting Started ............................................................................................................................................................ 3

Chapter 2 EasySet ...................................................................................................................................................................... 12

Chapter 3 System Settings ........................................................................................................................................................ 13

Chapter 5 USB Interface ............................................................................................................................................................ 50

Chapter 7 Data Formatter ........................................................................................................................................................ 200

Introduction .................................................................................................................................................................. 200

Chapter 8 Prefix & Suffix ......................................................................................................................................................... 224

Introduction .................................................................................................................................................................. 224

Chapter 9 Batch Programming ................................................................................................................................................ 242

Introduction .................................................................................................................................................................. 242

Appendix ................................................................................................................................................................................... 245

Digit Barcodes .............................................................................................................................................................. 245

 Chapter 1, Getting Started : Gives a general description of the FM30.

 Chapter 4, RS-232 Interface : Describes how to configure RS-232 communication parameters.

 Chapter 5, USB Interface : Describes how to configure USB communication parameters.

This icon indicates something relevant to this manual.

Features of the FM30

PIN Signal Type Function

The following trigger circuit is provided for reference.

USB port on the host device

RS-232 port on the host device

4. Connect the power adapter to a power outlet.

Power off the scanner

Reboot the scanner

2. For a successful read, the scanner will beep.

 The scan window should be kept clean.

 Do not scratch the scan window.

 Do not spray any liquid on the scan window.

EasySet supports 32-bit/64-bit Microsoft WinXP/Win7/Win 8/Win 8.1/Win 10 operating systems.

Chapter 3 System Settings

For more information, refer to the Serial Programming Command Manual.

Programming Barcode/ Programming Command/Function

1. The No Case Conversion barcode.

2. The No Case Conversion command.

3. The description of feature/option.

4. ** indicates factory default settings.

Use of Programming Command

Prefix: “~<SOH>0000” (HEX: 7E 01 30 30 30 30), 6 characters.

Suffix: “;<ETX>” (HEX: 3B 03), 2 characters.

<ENQ> (HEX: 05) Indicates an invalid Tag or SubTag command.

Use of Programming Barcodes

** Do Not Transmit Programming Barcode Data

Transmit Programming Barcode Data

Normal: Illumination LEDs are turned on during image capture.

Off: Illumination LEDs are off all the time.

Illumination LED Selection

Good Read LED

Good Read LED Duration

Set the Good Read LED duration to 800ms:

1. Scan the Enter Setup barcode.

2. Scan the Custom barcode.

5. Scan the Exit Setup barcode.

Good Read LED Selection

Barcode Pay Mode

Good Read Beep

Good Read Beep Duration