PRODUCT DATA SHEET August 31, 2018 (Revision of April 17, 2018)

SIGMADUR™ 540

DESCRIPTION
Two-component, high-gloss, VOC-compliant epoxy acrylic finish

PRINCIPAL CHARACTERISTICS
• Non-isocyanate
• Excellent gloss and color retention
• Non-chalking, non-yellowing
• Long pot life but quick-drying
• Can be recoated even after long exposure periods

COLOR AND GLOSS LEVEL

• Wide color range
• Gloss

BASIC DATA AT 20°C (68°F)

Data for mixed product

Number of components Two

Mass density 1.3 kg/l (10.8 lb/US gal)

Volume solids 54 ± 2%

VOC (Supplied) Directive 1999/13/EC, SED: max. 324.0 g/kg

UK PG 6/23(92) Appendix 3: max. 411.0 g/l (approx. 3.4 lb/US gal)
Recommended dry film thickness 50 - 60 µm (2.0 - 2.4 mils) depending on system

Theoretical spreading rate 10.8 m²/l for 50 µm (433 ft²/US gal for 2.0 mils)

Dry to touch 2 hours

Full cure after 7 days

Shelf life Base: at least 36 months when stored cool and dry
Hardener: at least 12 months when stored cool and dry

Notes:
- See ADDITIONAL DATA – Spreading rate and film thickness
- See ADDITIONAL DATA – Overcoating intervals
- See ADDITIONAL DATA – Curing time

RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES

Substrate conditions
• Compatible previous coat must be dry and free from any contamination
• Surface of previous coat should be sufficiently roughened if necessary

Ref. 7740 Page 1/5

PRODUCT DATA SHEET August 31, 2018 (Revision of April 17, 2018)

SIGMADUR™ 540

Substrate temperature
• Substrate temperature during application and curing should be above 5°C (41°F)
• Substrate temperature during application and curing should be at least 3°C (5°F) above dew point

INSTRUCTIONS FOR USE

Mixing ratio by volume: base to hardener 89.5:10.5
• Adding too much thinner results in reduced sag resistance
• The temperature of the mixed base and hardener should preferably be above 15°C (59°F), otherwise extra thinner may be
required to obtain application viscosity
• If required, thinner should be added after mixing the components

Induction time
None

Pot life
6 hours at 20°C (68°F)

Note: See ADDITIONAL DATA – Pot life

Air spray

Recommended thinner
THINNER 91-92

Volume of thinner
5 - 10%, depending on required thickness and application conditions

Nozzle orifice
1.0 - 1.5 mm (approx. 0.040 - 0.060 in)

Nozzle pressure
0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)

Ref. 7740 Page 2/5

PRODUCT DATA SHEET August 31, 2018 (Revision of April 17, 2018)

SIGMADUR™ 540

Airless spray

Recommended thinner
THINNER 91-92

Volume of thinner
0 - 5%, depending on required thickness and application conditions

Nozzle orifice
Approx. 0.38 – 0.46 mm (0.015 – 0.018 in)

Nozzle pressure
15.0 MPa (approx. 150 bar; 2176 p.s.i.)

Note: In order to achieve the optimum finish and cosmetic appearance, the product may be thinned by 10% and applied using
an air-assisted airless spray gun set up with a smaller tip size of 0.28 – 0.38 mm (0.011 – 0.015 in)

Brush/roller

Recommended thinner
THINNER 91-92

Volume of thinner
0 – 5%

Cleaning solvent
THINNER 91-92

ADDITIONAL DATA

Spreading rate and film thickness

DFT Theoretical spreading rate

50 µm (2.0 mils) 10.8 m²/l (433 ft²/US gal)

60 µm (2.4 mils) 9.0 m²/l (361 ft²/US gal)

Overcoating interval for DFT up to 50 µm (2.0 mils)

Overcoating with... Interval 5°C (41°F) 10°C (50°F) 20°C (68°F) 30°C (86°F)

itself Minimum 24 hours 16 hours 8 hours 6 hours

Maximum Unlimited Unlimited Unlimited Unlimited

Note: Surface should be dry and free from any contamination

Ref. 7740 Page 3/5

PRODUCT DATA SHEET August 31, 2018 (Revision of April 17, 2018)

SIGMADUR™ 540

Curing time for DFT up to 50 µm (2.0 mils)

Substrate temperature Dry to handle Full cure

5°C (41°F) 22 hours 14 days

10°C (50°F) 16 hours 12 days
20°C (68°F) 10 hours 7 days
30°C (86°F) 6 hours 4 days

Note: Adequate ventilation must be maintained during application and curing (please refer to INFORMATION SHEETS 1433 and
1434)

Pot life (at application viscosity)

Mixed product temperature Pot life

10°C (50°F) 10 hours

20°C (68°F) 6 hours
30°C (86°F) 3 hours

SAFETY PRECAUTIONS
• For paint and recommended thinners see INFORMATION SHEETS 1430, 1431 and relevant Material Safety Data Sheets
• This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact
between the wet paint and exposed skin or eyes
• Avoid at all times inhalation of aerosol spray mist

WORLDWIDE AVAILABILITY
It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight
modification of the product is sometimes necessary to comply with local or national rules/circumstances. Under these
circumstances an alternative product data sheet is used.

REFERENCES
• CONVERSION TABLES INFORMATION SHEET 1410
• EXPLANATION TO PRODUCT DATA SHEETS INFORMATION SHEET 1411
• SAFETY INDICATIONS INFORMATION SHEET 1430
• SAFETY IN CONFINED SPACES AND HEALTH SAFETY, EXPLOSION HAZARD – INFORMATION SHEET 1431
TOXIC HAZARD
• RELATIVE HUMIDITY – SUBSTRATE TEMPERATURE – AIR TEMPERATURE INFORMATION SHEET 1650

Ref. 7740 Page 4/5

PRODUCT DATA SHEET August 31, 2018 (Revision of April 17, 2018)

SIGMADUR™ 540

WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifications for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the
rightful claim of any third person for infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER
STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE,
ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the
applicable shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar
Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT. The information in this sheet is intended for guidance only and is based upon
laboratory tests that PPG believes to be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or
suggestions relating to the use of the PPG product, whether in technical documentation, or in response to a specific inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The
product and related information is designed for users having the requisite knowledge and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own
particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk. PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this information (unless there are written agreements
stating otherwise). Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. This sheet supersedes all previous versions and it is the
Buyer’s responsibility to ensure that this information is current prior to using the product. Current sheets for all PPG Protective & Marine Coatings Products are maintained at www.ppgpmc.com. The English text of
this sheet shall prevail over any translation thereof.

The PPG logo, and all other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.

Ref. 7740 Page 5/5