279 Ultra-slim Photoelectric Sensor Amplifier Built-in

EX-10 SERIES Ver.2

■■General terms and conditions.............. F-3 ■■Selection guide.............................. P.231~
FIBER Related Information
SENSORS   Glossary of terms / General precautions......P.1549~ / P.1552~ ■■Korea’s S-mark.............................. P.1602
LASER
SENSORS

PHOTOELECTRIC
SENSORS
Ver.2 Recognition
(Excluding some models)
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS Certified
(Some models only)
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS

SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS

MEASUREMENT
SENSORS panasonic.net/id/pidsx/global PNP output
type available
STATIC
CONTROL
DEVICES
LASER
MARKERS

PLC
Amplifier built-in extraordinarily small and slim size
HUMAN MACHINE
INTERFACES Smallest body, just 3.5 mm 0.138 in thick Flexible mounting
ENERGY
MANAGEMENT It can be mounted in a very The diffuse reflective type sensor is front sensing and is
SOLUTIONS
small space as its size is just so thin that it gives an impression of being just pasted
FA COMPONENTS W10 × H14.5 × D3.5 mm on the mounting base. The thru-beam type is available
W0.394 × H0.571 × D0.138 in as front sensing type, as well as, side sensing type,
MACHINE VISION (thru-beam, front sensing type). allowing flexible mounting.
SYSTEMS
Thru-beam Diffuse reflective
UV CURING • Front sensing type • Side sensing type • Front sensing type
SYSTEMS

Selection
Guide
Amplifier
Built-in
Power Supply
Built-in
Amplifier-
separated
A wide variety of narrow-beam type! Light diffusion is approx. 1/2 of standard type. EX-□S□
EX-Z Less interference with no slit, Possible to sense a minute object Long sensing range of 1 m 3.281
CX-400
narrow-pitch can be set. less than ø0.5 mm ø0.039 in with ft with narrow beam
no slit.
CY-100 The pitch of installation is 1/2 of A long 1 m 3.281 ft sensing range is
conventional models, so that the The series is applicable to sense a possible with narrow beam.
EX-10
close-installation is possible. No cost minute object without any cost.
EX-20 is necessary to purchase or install
EX-30 a slit.
EX-40
CX-440 EX-11□ / EX-11E□

EQ-30 ø0.5mm
EQ-500 EX-11S□
EX-11S□ / EX-11SE□
MQ-W
RX-LS200
RX EX-19S□

RT-610
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
280

APPLICATIONS FIBER
SENSORS

Positioning of PCBs Detecting ICs Detecting PCB rack LASER

SENSORS

PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
EX-19S□ SENSORS
SAFETY LIGHT
CURTAINS /
Transparent stick SAFETY COMPONENTS
PRESSURE /
FLOW
IC EX-15□ SENSORS
INDUCTIVE
EX-14□ PROXIMITY
SENSORS
PARTICULAR
Detecting wafer cassette Detecting thin ring Checking for absence of capacitor in tray USE SENSORS

SENSOR
EX-14□ OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS

MEASUREMENT
SENSORS
STATIC
EX-13E□ CONTROL
DEVICES
Guide LASER
EX-14□
MARKERS

PLC
BASIC PERFORMANCE
HUMAN MACHINE
Electric power saving * High-speed response time: 0.5 ms INTERFACES
ENERGY
MANAGEMENT
The EX-10 series The sensor is suitable for detecting small and high- SOLUTIONS
achieves reductions speed traveling objects.
in power consumption A maximum 35 % reduction
FA COMPONENTS
of up to 65 %. These compared to conventional
sensors MACHINE VISION
sensors contribute SYSTEMS
to environmental
friendliness. UV CURING
SYSTEMS
* Effective from production
in October 2010.

Selection
Guide
Amplifier
Minimum sensing object: ø1 mm ø0.039 in EX-11(E)□, EX-15(E)□ Long sensing range: 1 m 3.281 ft EX-19(E)□ Built-in
Power Supply
Built-in
Amplifier-
EX-11□, EX-11E□, EX-15 and A sensing range of 1 m separated
EX-15E are incorporated 3.281 ft has been realized
with ø1 mm ø0.039 in with a slim size of just 3.5 1m EX-Z
slit masks so that ø1 mm mm 0.138 in. It can be used 3.281 ft
ø0.039 in, or more, object to detect even wide IC trays. CX-400
can be detected. Hence, CY-100
they are suitable for precise
EX-10
positioning or small parts
detection. EX-20

Background suppression EX-14□ EX-30

EX-40
Hardly affected by background Black object reliably detected CX-440
The best distance
Even a specular background It can reliably detect dark is approx. 10 mm EQ-30
separated by 100 mm 3.937 Background
color objects since it is 0.394 in from the
object. EQ-500
in, or more, is not detected. 100 mm convergent reflective type.
3.937 in
(However, the background MQ-W
should be directly opposite. RX-LS200
A spherical or curved
RX
background may be
detected.) RT-610
 EX-10 SERIES Ver.2
281 Ultra-slim Photoelectric Sensor

FIBER ENVIRONMENTAL RESISTANCE

SENSORS

LASER Incorporated an inverter countermeasure circuit * Waterproof IP67

SENSORS

PHOTOELECTRIC The EX-10 series become Fluorescent light The sensors features an IP67 rating to allow their use
SENSORS significantly stronger in process lines where water is used or splashed.
MICRO against inverter light and Rust-resistant stainless steel sensor mounting brackets
PHOTOELECTRIC other extraneous light. are available.
SENSORS
* Effective from production in
AREA Note: If water splashes on the sensor during sensing operation, it may
SENSORS October 2010.
sense water as an object.
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS Bending durability EX-□-R
PRESSURE /
FLOW
SENSORS Bending-resistant cable type EX-□-R is available. It is
INDUCTIVE
PROXIMITY
most suitable for moving parts, such as robot arm, etc.
SENSORS
PARTICULAR
USE SENSORS
MOUNTING / SIZE
SENSOR Mountable with M3 screws
OPTIONS
SIMPLE Non-corrosive stainless steel type sensor mounting bracket is also available.
WIRE-SAVING
UNITS • MS-EX10-1 • MS-EX10-2 • MS-EX10-3
WIRE-SAVING [Cold rolled carbon steel (SPCC)] [Cold rolled carbon steel (SPCC)] [Cold rolled carbon steel (SPCC)]
SYSTEMS
MS-EX10-11 MS-EX10-12 MS-EX10-13
MEASUREMENT [Stainless steel (SUS304)] [Stainless steel (SUS304)] [Stainless steel (SUS304)]
SENSORS (L-shaped mounting bracket)
mounting bracket for the front mounting bracket for the side
STATIC sensing type sensing type
CONTROL
DEVICES M3 screws
LASER
MARKERS

PLC

M3 screws
HUMAN MACHINE
INTERFACES
M3 screws
ENERGY
MANAGEMENT Note: Sensor mounting brackets can not be used for
SOLUTIONS
the narrow beam type (EX-□S□).
FA COMPONENTS
Red beam makes beam alignment easy
MACHINE VISION
SYSTEMS
The red LED beam projected from the emitter helps you
UV CURING to align the sensor heads.
SYSTEMS

FUNCTIONS VARIETIES
Bright 2-color indicator Operation mode switch EX-15□/17□
Selection
Guide A convenient 2-color Thru-beam type sensor incorporated with an operation
Amplifier
Built-in indicator has been mode switch on the bifurcation is also available. It helps
Power Supply incorporated in the you to test the operability before start-up.
Built-in
Amplifier- miniature body.
separated

2-color indicator
EX-Z
Orange: Operation indicator
CX-400 Green: Stability indicator
Operation mode switch
CY-100
Even for the thru-beam
EX-10 Operation indicator SENS.
type sensor, only three
(Orange)
EX
-17
wires have to be connected.
EX-20
EX-30
OTHERS
EX-40 Less resources used *
CX-440
Based on environmental
EQ-30
considerations, simplified
EQ-500 packaging is used in order
MQ-W to reduce waste.
In addition, the bag is
RX-LS200
made from polyethylene
RX which produces no toxic
RT-610 gases even when burned.
* Effective from production in
October 2010.
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
282

ORDER GUIDE FIBER

SENSORS

LASER
SENSORS
Model No.(Note 2) Output
Type Appearance Sensing range operation Output PHOTO-
NPN output PNP output ELECTRIC
SENSORS
EX-11A EX-11A-PN Light-ON MICRO
150 mm 5.906 in PHOTO-
ELECTRIC
EX-11B EX-11B-PN Dark-ON SENSORS

500 mm EX-13A EX-13A-PN Light-ON AREA

SENSORS
19.685 in
EX-13B EX-13B-PN Dark-ON
Front sensing

SAFETY LIGHT
CURTAINS /
SAFETY
1m EX-19A EX-19A-PN Light-ON COMPONENTS
3.281 ft PRESSURE /
EX-19B EX-19B-PN Dark-ON FLOW
SENSORS
switch on the bifurcation

150 mm 5.906 in EX-15 EX-15 -PN INDUCTIVE

With operation mode

Switchable PROXIMITY
either SENSORS
Light-ON or PARTICULAR
500 mm USE
EX-17 EX-17-PN Dark-ON
Thru-beam

19.685 in SENSORS

NPN open- SENSOR

EX-11EA EX-11EA-PN Light-ON
Standard type

collector OPTIONS
150 mm 5.906 in
transistor
EX-11EB EX-11EB-PN Dark-ON
or
SIMPLE
WIRE-SAVING
UNITS
EX-13EA EX-13EA-PN Light-ON PNP open-
500 mm
collector
19.685 in WIRE-SAVING
EX-13EB EX-13EB-PN Dark-ON transistor SYSTEMS
Side sensing

1m EX-19EA EX-19EA-PN Light-ON MEASURE-

MENT
3.281 ft SENSORS
EX-19EB EX-19EB-PN Dark-ON
STATIC
CONTROL
switch on the bifurcation

DEVICES
150 mm 5.906 in EX-15E -
With operation mode

Switchable
either LASER
Light-ON or MARKERS
500 mm
19.685 in EX-17E - Dark-ON
PLC
Convergent reflective
(Diffused beam type)

Front sensing

HUMAN
EX-14A EX-14A-PN Light-ON MACHINE
INTERFACES
2 to 25 mm 0.079 to 0.984 in (Note 1)
ENERGY
(Convergent point: 10 mm 0.394 in) MANAGEMENT
EX-14B EX-14B-PN Dark-ON SOLUTIONS

FA
EX-11SA EX-11SA-PN Light-ON COMPONENTS
150 mm 5.906 in
EX-11SB EX-11SB-PN Dark-ON MACHINE
Front sensing

VISION
SYSTEMS
500 mm EX-13SA EX-13SA-PN Light-ON
19.685 in UV
Narrow beam type

EX-13SB EX-13SB-PN Dark-ON NPN open- CURING

collector SYSTEMS
Thru-beam

1m EX-19SA EX-19SA-PN Light-ON transistor

3.281 ft or
EX-19SB EX-19SB-PN Dark-ON PNP open-
collector
EX-11SEA EX-11SEA-PN Light-ON transistor
Side sensing

150 mm 5.906 in Selection

Guide
EX-11SEB EX-11SEB-PN Dark-ON
Amplifier
Built-in
500 mm EX-13SEA EX-13SEA-PN Light-ON
Power Supply
19.685 in Built-in
EX-13SEB EX-13SEB-PN Dark-ON
Amplifier-
separated

NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets
(MS-EX10-□). Sensor mounting brackets (MS-EX10-□) can not be used for the narrow beam type (EX-□S□). EX-Z
Notes: 1) The sensor does not detect even a specular background if it is separated by 100 mm 3.937 in or more. (However, the background should be directly CX-400
opposite. A spherical or curved background may be detected.)
2) The model No. with “P” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver. CY-100

EX-10
Bending-resistant cable type
EX-20
Bending-resistant cable type is also available for NPN output type. (excluding narrow beam type EX-□S□ and sensor with operation mode switch on the
EX-30
bifurcation EX-15□/17□)
When ordering this type, suffix “-R” to the model No. EX-40
(e.g.) Bending-resistant cable type of EX-11A is “EX-11A-R”.
CX-440

5 m 16.404 ft cable length type EQ-30

5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available for NPN output type. (excluding narrow beam type EX-□S□ and bending-resistant cable type) EQ-500
When ordering this type, suffix “-C5” to the model No. MQ-W
(e.g.) 5 m 16.404 ft cable length type of EX-11A is “EX-11A-C5”.
RX-LS200

RX

RT-610
 EX-10 SERIES Ver.2
283 Ultra-slim Photoelectric Sensor

FIBER
SENSORS
OPTIONS
LASER
SENSORS
NOTE: Sensor mounting brackets can not be used for the narrow beam type (EX-□S□). Sensor mounting bracket
PHOTO-
ELECTRIC
• MS-EX10-1 • MS-EX10-11
SENSORS
MICRO
PHOTO- Designation Model No. Description
ELECTRIC
SENSORS

AREA Mounting bracket for the front sensing type sensor [Cold rolled carbon steel (SPCC)]
SENSORS MS-EX10-1 (The thru-beam type sensor needs two brackets.)
SAFETY LIGHT
CURTAINS / Mounting bracket for the side sensing type sensor [Cold rolled carbon steel (SPCC)]
SAFETY MS-EX10-2 (The thru-beam type sensor needs two brackets.)
COMPONENTS
PRESSURE /
FLOW L-shaped mounting bracket sensor [Cold rolled carbon steel (SPCC)]
SENSORS Sensor mounting MS-EX10-3 (The thru-beam type sensor needs two brackets.) Material: Cold rolled Material: Stainless
INDUCTIVE bracket carbon steel (SPCC) steel (SUS304)
PROXIMITY (Note 1) Mounting bracket for the front sensing type sensor [Stainless steel (SUS304)] (Uni-chrome plated) Two M2 (length 4 mm
SENSORS MS-EX10-11 (The thru-beam type sensor needs two brackets.) Two M2 (length 4 mm 0.157 in) pan head
PARTICULAR 0.157 in) pan head screws [stainless
USE Mounting bracket for the side sensing type sensor [Stainless steel (SUS304)] screws are attached. steel (SUS304)] are
SENSORS MS-EX10-12 (The thru-beam type sensor needs two brackets.) attached.
SENSOR
OPTIONS L-shaped mounting bracket [Stainless steel (SUS304)]
MS-EX10-13 (The thru-beam type sensor needs two brackets.)
SIMPLE • MS-EX10-2 • MS-EX10-12
WIRE-SAVING
UNITS • Sensing range: 600 mm 23.622 in [EX-19□]
Slit on one side 250 mm 9.843 in [EX-13□, EX-17□]
WIRE-SAVING
SYSTEMS • Min. sensing object: ø2 mm ø0.079 in
OS-EX10-12
(Slit size ø1.2 mm ø0.047 in)
MEASURE- • Sensing range: 400 mm 15.748 in [EX-19□]
MENT
SENSORS Slit on both sides 200 mm 7.874 in [EX-13□, EX-17□]
• Min. sensing object: ø1.2 mm ø0.047 in
STATIC
CONTROL
DEVICES • Sensing range: 800 mm 31.496 in [EX-19□]
Slit on one side 350 mm 13.780 in [EX-13□]
LASER Material: Cold rolled Material: Stainless
MARKERS • Min. sensing object: ø2 mm ø0.079 in
Slit mask OS-EX10-15 carbon steel (SPCC) steel (SUS304)
(Slit size ø1.5 mm ø0.059 in) (Uni-chrome plated) Two M2 (length 8 mm
• Sensing range: 500 mm 19.685 in [EX-19□]
PLC Two M2 (length 8 mm 0.315 in) pan head
Slit on both sides 300 mm 11.811 in [EX-13□]
0.315 in) pan head screws [stainless
• Min. sensing object: ø1.5 mm ø0.059 in screws are attached. steel (SUS304)] are
HUMAN
MACHINE attached.
INTERFACES • Sensing range: 400 mm 15.748 in [EX-19E□] (Note 3)
ENERGY Slit on one side 250 mm 9.843 in [EX-13E□, EX-17E□]
MANAGEMENT OS-EX10E-12 • Min. sensing object: ø2 mm ø0.079 in
SOLUTIONS
(Slit size ø1.2 mm ø0.047 in) • MS-EX10-3 • MS-EX10-13
FA • Sensing range: 200 mm 7.874 in [EX-13E□, EX-17E□]
Slit on both sides
COMPONENTS • Min. sensing object: ø1.2 mm ø0.047 in
MACHINE Sensor checker It is useful for beam alignment of thru-beam type sensors. The optimum
VISION
SYSTEMS (Note 2)
CHX-SC2 receiver position is given by indicators, as well as an audio signal.
UV
CURING Mounting screws with washers (50 pcs. lot). It can mount
SYSTEMS Mounting screw MS-M2 securely as it is spring washer attached.
Notes: 1) Can not be used for the narrow beam type (EX-□S□).
2) Refer to p.959~ for the sensor checker CHX-SC2.
3) Since EX-19E□ has a built-in ø1 mm ø 0.039 in slit in the emitter, be sure to mount it in the Material: Cold rolled Material: Stainless steel
receiver. carbon steel (SPCC) (SUS304)
Selection (Uni-chrome plated) Two M2 (length 4 mm
Guide
Amplifier
Slit mask Sensor checker Two M2 (length 4 mm 0.157 in) pan head
Built-in 0.157 in) pan head screws [stainless
Power Supply • OS-EX10-12 • OS-EX10E-12 Example of mounting • CHX-SC2 screws, and two M2 steel (SUS304)] and
Built-in (length 8 mm 0.315 in) two M2 (length 8 mm
• OS-EX10-15 (OS-EX10E-12)
Amplifier- pan head screws are 0.315 in) pan head
separated attached. screws [stainless steel
PO
W
ER C
H
X-
(SUS304)] are attached.
SC
LE
VE
L
2

EX-Z

CX-400
Sensor checker
CY-100

EX-10
Tighten along with the sensor
EX-20 mounting bracket.
EX-30

EX-40

CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
284

SPECIFICATIONS FIBER
SENSORS

LASER
SENSORS
Thru-beam • standard type PHOTO-
Type ELECTRIC
SENSORS
Front sensing Side sensing Front sensing Side sensing Front sensing Side sensing MICRO
PHOTO-
Model No. Light-ON EX-11A(-PN) EX-11EA(-PN) EX-13A(-PN) EX-13EA(-PN) EX-19A(-PN) EX-19EA(-PN) ELECTRIC
SENSORS
(Note 2) Dark-ON EX-11B(-PN) EX-11EB(-PN) EX-13B(-PN) EX-13EB(-PN) EX-19B(-PN) EX-19EB(-PN)
Item AREA
SENSORS
CE marking directive compliance EMC Directive, RoHS Directive SAFETY LIGHT
CURTAINS /
Sensing range 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft SAFETY
COMPONENTS

ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object ø2 mm ø0.079 in PRESSURE /

FLOW
(Completely beam interrupted object) (Completely beam interrupted object) opaque object SENSORS
Setting distance Setting distance Completely beam INDUCTIVE
Min. sensing object between emitter between emitter interrupted object PROXIMITY
SENSORS
and receiver: and receiver: Setting distance between
150 mm 5.906 in 500 mm 19.685 in emitter and receiver: PARTICULAR
USE
1 m 3.281 ft SENSORS

Hysteresis –
SENSOR
OPTIONS
Repeatability (perpendicular to sensing axis) 0.05 mm 0.002 in or less
SIMPLE
Supply voltage 12 to 24 V DC ±10 %   Ripple P-P 10 % or less WIRE-SAVING
UNITS

Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less WIRE-SAVING

SYSTEMS
<NPN output type> <PNP output type>
NPN open-collector transistor PNP open-collector transistor MEASURE-
MENT
• Maximum sink current: 50 mA • Maximum source current: 50 mA SENSORS
Output
• Applied voltage: 30 V DC or less (between output and 0 V) • Applied voltage: 30 V DC or less (between output and +V) STATIC
• Residual voltage: 2 V or less (at 50 mA sink current) • Residual voltage:2
 V or less (at 50 mA source current) CONTROL
DEVICES
1 V or less (at 16 mA sink current) 1 V or less (at 16 mA source current)
LASER
Utilization category DC-12 or DC-13 MARKERS

Short-circuit protection Incorporated

PLC
Response time 0.5 ms or less
HUMAN
Operation indicator Orange LED (lights up when the output is ON) MACHINE
INTERFACES

Incident beam indicator – ENERGY

MANAGEMENT
SOLUTIONS
Green LED
Stability indicator
(lights up under stable light received condition or stable dark condition) FA
COMPONENTS
Pollution degree 3 (Industrial environment)
MACHINE
VISION
Protection IP67 (IEC) SYSTEMS
Environmental resistance

Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F UV
CURING
SYSTEMS
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH

Ambient illuminance Incandescent light: 3,000 ℓx or less at the light-receiving face

Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure

Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure Selection
Guide
Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude in X, Y and Z directions for two hours each Amplifier
Built-in
Power Supply
Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each Built-in
Amplifier-
Emitting element Red LED [Peak emission wavelength: 680 nm 0.027 mil (EX-19E□: 624 nm 0.025 mil), modulated] separated

Material Enclosure: Polyethylene terephthalate, Lens: Polyalylate

Cable (Note 3) 0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long EX-Z

CX-400
Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (thru-beam type: emitter and receiver).
CY-100
Weight Net weight (each emitter and receiver): 20 g approx., Gross weight: 50 g approx.
EX-10
Accessories Mounting screws: 1 set
EX-20
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) Model Nos. having the suffix “-PN” are PNP output type. EX-30
3) The bending-resistant cable type (model Nos. having suffix “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable,
EX-40
2 m 6.562 ft long.
CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610
 EX-10 SERIES Ver.2
285 Ultra-slim Photoelectric Sensor

FIBER
SENSORS
SPECIFICATIONS
LASER
SENSORS
Convergent reflective
Thru-beam • narrow beam type Thru-beam · with operation mode switch on bifurcation
PHOTO-
Type (Diffused beam type)
ELECTRIC
SENSORS
MICRO
Front sensing Side sensing Front sensing Side sensing Front sensing Front sensing Front sensing Side sensing Front sensing Side sensing
PHOTO-
ELECTRIC
SENSORS Model No. Light-ON EX-11SA(-PN) EX-11SEA(-PN) EX-13SA(-PN) EX-13SEA(-PN) EX-19SA(-PN) EX-14A(-PN) EX-15 EX-15E EX-17 EX-17E
(Note 2) Dark-ON EX-11SB(-PN) EX-11SEB(-PN) EX-13SB(-PN) EX-13SEB(-PN) EX-19SB(-PN) EX-14B(-PN) (Note 3) (Note 3) (Note 3) (Note 3)
AREA
SENSORS
Item
CE marking directive compliance EMC Directive, RoHS Directive –
SAFETY LIGHT
CURTAINS /
SAFETY 2 to 25 mm 0.079
COMPONENTS
Sensing range 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft to 0.984 in (Note 4) 150 mm 5.906 in 500 mm 19.685 in
PRESSURE /
FLOW (Conv. point: 10 mm 0.394 in)
SENSORS

INDUCTIVE
ø0.5 mm ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object
ø0.002 in
ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object ø0.1 mm ø0.004 (Completely beam interrupted object) (Completely beam interrupted object)
PROXIMITY
SENSORS
opaque object Setting distance Setting distance
(Completely beam interrupted object) (Completely beam interrupted object) in copper wire
PARTICULAR Min. sensing object (Completely between emitter between emitter
USE (Note 5) (Note 5) Setting distance:
SENSORS beam interrupted and receiver: and receiver:
object) 10 mm 0.394 in
150 mm 5.906 in 500 mm 19.685 in
SENSOR (Note 5)
OPTIONS

– 15 % or less of operation –
SIMPLE Hysteresis
WIRE-SAVING distance (Note 4)
UNITS
Repeatability (perpendicular to sensing axis) 0.05 mm 0.002 in or less 0.1 mm 0.004 in or less 0.05 mm 0.002 in or less
WIRE-SAVING
SYSTEMS
Supply voltage 12 to 24 V DC ±10 %   Ripple P-P 10 % or less
MEASURE-
MENT Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less 13 mA or less 25 mA or less
SENSORS
<NPN output type> <PNP output type> NPN open-collector transistor
STATIC
CONTROL NPN open-collector transistor PNP open-collector transistor • Maximum sink current: 100 mA
DEVICES • M aximum source current: 50 mA
• M aximum sink current: 50 mA • Applied voltage: 30 V DC or less (between output and 0 V)
Output • A pplied voltage: 30 V DC or less (between output and 0 V) • A pplied voltage: 30 V DC or less (between output and +V) • R esidual voltage: 2 V or less
LASER
MARKERS • R esidual voltage: 2 V or less (at 50 mA sink current) • R esidual voltage: 2 V or less (at 50 mA source current) (at 100 mA sink current)
1 V or less (at 16 mA sink current) 1 V or less (at 16 mA source current) 1 V or less (at 16 mA sink current)
PLC
Utilization category DC-12 or DC-13 –
HUMAN
MACHINE Short-circuit protection Incorporated
INTERFACES

ENERGY
Response time 0.5 ms or less
MANAGEMENT
SOLUTIONS Operation indicator Orange LED (lights up when the output is ON) Orange LED (lights up when the output is ON), located on the bifurcation
FA Orange LED (lights up under light received
COMPONENTS Incident beam indicator –
condition), located on the receiver
MACHINE
VISION Green LED (lights up under stable light received
SYSTEMS Green LED
Stability indicator condition or stable dark condition), located on the
(lights up under stable light received condition or stable dark condition)
UV receiver
CURING
SYSTEMS
Pollution degree 3 (Industrial environment) –

Protection IP67 (IEC)

Environmental resistance

Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F
Selection Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Guide
Amplifier
Built-in Ambient illuminance Incandescent light: 3,000 ℓx or less at the light-receiving face
Power Supply
Built-in Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Amplifier-
separated Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure

Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude in X, Y and Z directions for two hours each
EX-Z
Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
CX-400
Emitting element Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated) Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
CY-100
Enclosure: Polyethylene terephthalate Enclosure: Polyethylene terephthalate
Material
EX-10 Lens: Polyalylate Lens: Polyalylate, Bifurcation: Polyalylate
EX-20 0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 0.2 mm2 3-core cabtyre cable, 2 m 6.562 ft long (beyond bifurcation;
Cable (Note 6)
2 m 6.562 ft long from emitter / receiver to bifurcation: 0.5 m 1.640 ft long)
EX-30

EX-40 Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (thru-beam type: emitter and receiver). Extension up to total 100 m 328 ft is possible with 0.3 mm2, or more, cable.

CX-440 Net weight (each emitter and receiver): 20 g approx., Net weight: 20 g approx.
Weight Net weight: 55 g approx., Gross weight: 80 g approx.
Gross weight: 50 g approx. Gross weight: 40 g approx.
EQ-30
Accessories Mounting screws: 1 set Mounting screws: 1 set Mounting screws: 1 set, Adjusting screwdriver: 1 pc.
EQ-500
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
MQ-W 2) Model Nos. having the suffix “-PN” are PNP output type.
RX-LS200 3) Either Light-ON or Dark-ON can be selected by the operation mode switch.
4) The sensing range and the hysteresis of convergent reflective type sensor are specified for white non-glossy paper (50 × 50 mm 1.969 × 1.969 in) as the object.
RX 5) The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
6) The bending-resistant cable type (model Nos. having suffix “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable,
RT-610
2 m 6.562 ft long.
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
286

I/O CIRCUIT AND WIRING DIAGRAMS FIBER

SENSORS

LASER
EX-11□  EX-11S□  EX-13□  EX-13S□  EX-19□  EX-19S□  EX-14□ NPN output type SENSORS

I/O circuit diagram Wiring diagram PHOTO-

ELECTRIC
SENSORS
Color code MICRO
PHOTO-
ELECTRIC
D1 (Brown) +V SENSORS

AREA
Sensor circuit

(Black) Load Brown SENSORS

D2 Output (Note) + 12 to 24 V DC SAFETY LIGHT
− ±10 % CURTAINS /
Load
Tr 50 mA max. Black (Note) + SAFETY
ZD 12 to 24 V DC COMPONENTS
(Blue) 0 V − ±10 %
PRESSURE /
FLOW
Blue SENSORS

Internal circuit Users’ circuit INDUCTIVE

Note: The emitter of the thru-beam type sensor does not incorporate the PROXIMITY
Note: The emitter of the thru-beam type sensor does not incorporate the SENSORS
black wire.
output. PARTICULAR
USE
SENSORS
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode SENSOR
OPTIONS
ZD: Surge absorption zener diode
Tr : NPN output transistor SIMPLE
WIRE-SAVING
UNITS

EX-11□-PN  EX-11S□-PN  EX-13□-PN  EX-13S□-PN  EX-19□-PN  EX-19S□-PN  EX-14□-PN PNP output type WIRE-SAVING

SYSTEMS

I/O circuit diagram Wiring diagram MEASURE-

MENT
SENSORS
Color code
STATIC
(Brown) +V CONTROL
DEVICES
Sensor circuit

ZD LASER
50 mA max. Brown MARKERS
+ 12 to 24 V DC
Tr ±10 %
D2 (Black) Output (Note) −
Load Black (Note) + 12 to 24 V DC PLC
D1 (Blue) 0 V − ±10 %
Load HUMAN
Blue MACHINE
INTERFACES
Internal circuit Users’ circuit
Note: The emitter of the thru-beam type sensor does not incorporate the ENERGY
Note: The emitter of the thru-beam type sensor does not incorporate the MANAGEMENT
output. black wire. SOLUTIONS

FA
COMPONENTS
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode MACHINE
ZD: Surge absorption zener diode VISION
SYSTEMS
Tr : PNP output transistor
UV
CURING
SYSTEMS
EX-15□  EX-15E□  EX-17□  EX-17E□ NPN output type

I/O circuit diagram EX-15□, EX-15E□, EX-17□, EX-17E□ wiring diagram

Color code
Selection
D1 Guide
(Brown) +V
Amplifier
Built-in
Sensor circuit

Load Power Supply

D2 (Black) Output + 12 to 24 V DC Built-in
− ±10 % Amplifier-
Tr 100 mA max. separated
ZD
(Blue) 0 V
EX-Z
Internal circuit Users’ circuit CX-400

CY-100
Symbols … D1: Reverse supply polarity protection diode
EX-10
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode EX-20
Tr : NPN output transistor
EX-30

EX-40
Brown
CX-440
Load
Black + 12 to 24 V DC EQ-30
− ±10 %
EQ-500
Blue
MQ-W

RX-LS200

RX

RT-610
 EX-10 SERIES Ver.2
287 Ultra-slim Photoelectric Sensor

FIBER
SENSORS
SENSING CHARACTERISTICS (TYPICAL)
LASER
SENSORS EX-11□  EX-11E□  EX-15□  EX-15E□ Thru-beam type *Optical properties of side sensing types (EX-□E□)
Due to the optical properties of side sensing types, note that sensing may
PHOTO- be affected if multiple sensors are positioned in such a way that optical
ELECTRIC Parallel deviation Angular deviation
SENSORS axes intersect as shown in the diagram below.
MICRO 200 200
PHOTO- 7.874 EX-11□ 7.874
ELECTRIC EX-15□
SENSORS
EX-11E□ Emitter 2 Receiver 1 Beam from Emitter 1
Setting distance L (mm in)
Setting distance L (mm in)

AREA 150 150

5.906 EX-15E□ 5.906 EX-11□ may be caught by Receiver 2.
SENSORS
EX-15□
SAFETY LIGHT
CURTAINS / 100 EX-11□ 100 EX-11E□ Emitter 1 Receiver 2
EX-11E□
SAFETY 3.937 EX-15□ 3.937 EX-15E□
COMPONENTS EX-15E□ Emitter
Emitter Emitter
PRESSURE / Emitter
FLOW 50 50
SENSORS
1.969 ℓ L ℓ L
θ
L
θ
L
Emitter 1 Receiver 1 There is no problem when
1.969
INDUCTIVE EX-11□ EX-11E□ sensors are installed in
ℓ × 2 or more
PROXIMITY Receiver Receiver EX-15□ Receiver Receiver EX-15E□ parallel
SENSORS 0 0
50 25 0 25 50 20 10 0 10 20 Emitter 2 Receiver 2 (although the distance
PARTICULAR 1.969 0.984 0.984 1.969 Left Center Right L between sensors should be
USE Left Center Right
SENSORS Operating angle θ ( ° ) ℓ × 2 or more).
Operating point ℓ (mm in)
SENSOR
OPTIONS

SIMPLE
EX-13□  EX-13E□  EX-17□  EX-17E□ Thru-beam type
WIRE-SAVING
UNITS
Parallel deviation Angular deviation Parallel deviation with slit Parallel deviation with slit
WIRE-SAVING masks (ø1.2 mm ø0.047 in) masks (ø1.5 mm ø0.059 in)
SYSTEMS
800 800 400 400
MEASURE- 31.496 31.496 15.748 EX-13□/17□ 15.748 Slit on one side
MENT Slit on one side or both sides
SENSORS
EX-13□/17□

Setting distance L (mm in)

Setting distance L (mm in)
Setting distance L (mm in)
Setting distance L (mm in)

600 EX-13□ 600 300 Slit on both sides 300

STATIC
CONTROL 23.622 EX-17□ 23.622 11.811 11.811
EX-13□ EX-13E□/17E□
DEVICES Slit on one side
EX-13E□ EX-17□
LASER 400 EX-17E□ 400 200 EX-13E□/17E□ 200
EX-13E□ Slit on
MARKERS 15.748 Emitter 15.748 7.874 7.874 Slit on one side,
EX-17E□ both sides Emitter Emitter
Emitter Emitter sensing range: 350 mm 13.78 in
Emitter Slit on both sides,
PLC 200 ℓ L 200 100 100 sensing range: 300 mm 11.81 in
ℓ θ θ ℓ L ℓ L
7.874 L 7.874 L L 3.937 3.937
EX-13□ EX-13E□ EX-13□ EX-13E□
HUMAN Receiver Receiver
MACHINE Receiver EX-17□ EX-17E□ Receiver EX-17□ Receiver Receiver EX-17E□
INTERFACES 0 0 0 0
100 50 0 50 100 20 10 0 10 20 40 20 0 20 40 100 50 0 50 100
ENERGY 3.937 1.969 1.969 3.937 Left Center Right 1.575 0.787 0.787 1.575 3.937 1.969 1.969 3.937
MANAGEMENT Left Center Right Operating angle θ ( ° ) Left Center Right Left Center Right
SOLUTIONS Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)

FA
COMPONENTS
EX-19□ Thru-beam type
MACHINE
VISION
SYSTEMS Parallel deviation Angular deviation Parallel deviation with slit Parallel deviation with slit
UV
CURING
masks (ø1.2 mm ø0.047 in) masks (ø1.5 mm ø0.059 in)
SYSTEMS
800
31.496
Slit on one side Slit on one side
1,000 1,000 1,000
Setting distance L (mm in)
Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

39.370 39.370 600 39.370

23.622
Selection Slit on both sides
Guide
400
Amplifier Emitter 15.748
Built-in 500 Emitter 500 500 Emitter
Emitter
Power Supply 19.685 19.685 19.685
θ
Built-in ℓ L 200 ℓ L
L ℓ L
Amplifier- 7.874 Slit on both sides
separated Receiver Receiver
Receiver Receiver
0 0 0 0
200 100 0 100 200 40 20 0 20 40 200 100 0 100 200 200 100 0 100 200
EX-Z 7.874 3.937 3.937 7.874 Left Center Right 7.874 3.937 3.937 7.874 7.874 3.937 3.937 7.874
Left Center Right Operating angle θ ( ° ) Left Center Right Left Center Right
CX-400 Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)

CY-100
EX-19E□ Thru-beam type EX-11S□/EX-11SE□ Thru-beam type EX-13S□/EX-13SE□ Thru-beam type EX-19S□ Thru-beam type
EX-10

EX-20 Parallel deviation Parallel deviation Parallel deviation Parallel deviation

200 800
EX-30 7.874 31.496
EX-13S□
EX-40 1,000 1,000
Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

39.370 150 600 39.370

CX-440 5.906 EX-11S□ EX-11SE□ 23.622
EX-13SE□
EQ-30
100 400
3.937 EX-11S□ EX-11SE□ 15.784 Emitter Emitter
EQ-500 500 Emitter 500
19.685 Emitter Emitter
Emitter 19.685
MQ-W 50 ℓ L ℓ L
ℓ 200
L 1.969 ℓ L ℓ L 7.874 ℓ L
RX-LS200 Receiver Receiver
Receiver Receiver Receiver
0 Receiver EX-13S□ EX-13SE□
RX 0 0 0
200 100 0 100 200 50 25 0 25 50 50 25 0 25 50 100 50 0 50 100
7.874 3.937 3.937 7.874 1.969 0.984 0.984 1.969 1.969 0.984 0.984 1.969 3.937 1.969 1.969 3.937
RT-610 Left Center Right
Left Center Right Left Center Right Left Center Right
Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)
Operating point ℓ (mm in)
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
288

SENSING CHARACTERISTICS (TYPICAL) FIBER

SENSORS

LASER
EX-14□ Convergent reflective type SENSORS

PHOTO-
Sensing fields ELECTRIC
SENSORS
• Horizontal (left and right) direction • Vertical (up and down) direction MICRO
PHOTO-
40 40 ELECTRIC
1.575 50 × 50 mm 1.969 × 1.969 in 1.575 SENSORS
Non-glossy paper
AREA
SENSORS
Setting distance L (mm in)

30 Setting distance L (mm in)

30
1.181 7 mm ℓ 1.181 50 × 50 mm SAFETY LIGHT
0.276 in L 1.969 × 1.969 in CURTAINS /
White Non-glossy paper SAFETY
COMPONENTS
20 20
0.787 White 0.787 PRESSURE /
FLOW
SENSORS
10 10 INDUCTIVE
0.394 0.394 ℓ PROXIMITY
N4 7.75 SENSORS
N4 mm L
0.305 in
0 0 PARTICULAR
10 5 0 5 10 10 5 0 5 10 USE
SENSORS
0.394 0.197 0.197 0.394 0.394 0.197 0.197 0.394
Left Center Right Down Center Up
Operating point ℓ (mm in) SENSOR
Operating point ℓ (mm in) OPTIONS

Correlation between lightness and sensing range Correlation between material (50 × 50 mm 1.969 × 1.969 in) and sensing range SIMPLE
WIRE-SAVING
40 80 UNITS
1.575 The sensing region (typical) is 3.150 The bars in the graph indicate
represented by oblique lines the sensing range (typical) WIRE-SAVING
SYSTEMS
in the left figure. However, the 60 for the respective material.
Sensing range L (mm in)

30
Sensing range L (mm in)

1.181 sensitivity should be set with 2.362 However, there is a slight MEASURE-
MENT
enough margin because of variation in the sensing range SENSORS
20 slight variation in products. 40 depending on the product. STATIC
0.787 1.575
Sensing region
Further, if there is a reflective CONTROL
DEVICES
object (conveyor, etc.) in the
10 20 background of the sensing LASER
0.394 0.787 MARKERS
10 object, since it affects the
0.394 sensing, separate it by more
convergent point

0 0

Distance to convergent point

N2 N4 N6 N8 Lightness shown on the left than twice the sensing range PLC
Black circuit board
Black rubber sheet
IC tray (Black)

Ceramic circuit board

White non-glossy paper
Stainless steel plate
Aluminum plate
(Hair line)
Aluminum-evaporated mirror
Glass epoxy printed circuit board
Distance to

Dark Lightness Light shown in the left graph.

may differ slightly from the HUMAN
(Green masked surface)

N1 N2 N3 N4 N5 N6 N7 N8 N9 actual object condition. MACHINE

INTERFACES

ENERGY
MANAGEMENT
SOLUTIONS

FA

PRECAUTIONS FOR PROPER USE

COMPONENTS
Refer to p.1552~ for general precautions.
MACHINE
VISION
SYSTEMS
Operation mode switch UV
• Never use this product as a sensing device (EX-15□, EX-15E□, EX-17□ and EX-17E□ only) CURING
SYSTEMS
for personnel protection.
• In case of using sensing devices for Operation mode switch
personnel protection, use products which L: Light-ON
meet laws and standards, such as OSHA, D: Dark-ON

ANSI or IEC etc., for personnel protection Selection

Guide
applicable in each region or country. Operation indicator (Orange) Amplifier
Lights up when the output is Built-in
ON. Power Supply
Mounting Built-in
Amplifier-
separated
• In case of mounting on tapped holes (Unit: mm in) Switch
Description
position
Side sensing Front sensing
EX-Z
Sensing Light-ON mode is set when the switch is turned fully CX-400
Sensing 11 direction clockwise (L side).
direction 0.433 CY-100
Attached screw 11
Attached screw M2 × 0.4 0.016 hole [M2 (length 8 0.315)] 0.433 Dark-ON mode is set when the switch is turned fully EX-10
tapped, 6 0.157 deep M2 × 0.4 0.016 hole counterclockwise (D side).
[M2 (length 10 0.394)] EX-20
tapped, 7 0.276 deep
EX-30
The tightening torque should be 0.2 N·m or less.
Others EX-40
• In case of using attached screws and nuts (Unit: mm in)
• Do not use during the initial transient time (50 ms) CX-440
Side sensing Front sensing after the power supply is switched on.
EQ-30
Flat washers
• Excess bending of the cable or stress applied to the
Sensing EQ-500
11 Sensing direction cable may disconnect the internal lead wire.
0.433 direction Nuts MQ-W
Spring washers Attached screw 11
Attached screw [M2 (length 8 0.315)] 0.433 RX-LS200
[M2 (length 10 0.394)]
RX
Thickness of Thickness of
mounting plate: 2 0.079 or less mounting plate: 2.5 0.098 or less
RT-610
The tightening torque should be 0.2 N·m or less.
 EX-10 SERIES Ver.2
289 Ultra-slim Photoelectric Sensor

FIBER
SENSORS
DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website.

LASER
SENSORS EX-11□  EX-11S□  EX-13□  EX-13S□  EX-19□  EX-19S□ Sensor
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO- Stability
ELECTRIC 10
SENSORS 0.394 indicator 3.5
3.5 6.45 (Green) 0.138
AREA 0.138 10 2.1
SENSORS 2.1 0.394 5.5 0.254 Operation 0.083
0.083 5.5 0.217 indicator
0.217 1.75
SAFETY LIGHT 0.069 (Orange)
CURTAINS / 1.75 0.069
SAFETY 1.75 1.5
COMPONENTS
1.75 0.069 0.069 0.059
PRESSURE /
FLOW
SENSORS
4 Beam- 4
INDUCTIVE 0.157 receiving 0.157
PROXIMITY 14.5 11 11 14.5
0.571 0.433 part 0.433 0.571
SENSORS

PARTICULAR
USE 4.5
SENSORS 4.5 Beam-
0.177 emitting 0.177
SENSOR part
OPTIONS 2-ø2.2 ø0.087 6.5 6.5 2-ø2.2 ø0.087
mounting holes 0.256 0.256
mounting holes
SIMPLE ø2.5 ø0.098 cable, 2 m 6.562 ft long ø2.5 ø0.098 cable, 2 m 6.562 ft long
WIRE-SAVING
UNITS

WIRE-SAVING Emitter Receiver

SYSTEMS

MEASURE-
MENT
SENSORS
EX-11E□  EX-11SE□  EX-13E□  EX-13SE□  EX-19E□  Sensor
STATIC
CONTROL
DEVICES

LASER
MARKERS Stability
indicator (Green)
10
PLC Operation 0.394
indicator (Orange) 6.45
10 0.254
HUMAN 0.394 4.5 4.5 1.75
MACHINE 1.75 0.069 0.177 0.177 0.069
INTERFACES 2.25 2.25 1.75 1.5
1.75 0.069 0.089 0.089 0.069 0.059
ENERGY
MANAGEMENT
SOLUTIONS
4 Beam- Beam-
0.157 4
FA emitting receiving 0.157
14.5 11
COMPONENTS 0.571 0.433 part part 11 14.5
0.433 0.571
MACHINE
VISION
SYSTEMS 4.5 4.5
0.177 0.177
UV
CURING 2-ø2.2 ø0.087 6.5
SYSTEMS 6.5 2-ø2.2 ø0.087
mounting holes 0.256 0.256
4.2 4.2 mounting holes
ø2.5 ø0.098 cable, 2 m 6.562 ft long 0.165 0.165
ø2.5 ø0.098 cable, 2 m 6.562 ft long

Emitter Receiver
Selection
Guide
Amplifier
Built-in
Power Supply EX-15  EX-17 Sensor EX-15E  EX-17E Sensor
Built-in
Amplifier-
separated Emitter 10 Receiver Stability indicator (Green)
Emitter Receiver
10 Stability indicator (Green) 10
0.394 Incident beam indicator (Orange)
5.5 1.75 0.394 Incident beam indicator (Orange) 0.394
1.75 0.217 10 0.394 3.5 0.069 6.45 0.254
3.5 0.069
EX-Z 0.138 6.45 0.254 0.138 4.5 4.5 1.75 0.069
1.75 4 1.5 1.75 0.177 0.177 1.5
5.5 1.75
1.75
0.069 4 4 1.75 0.059
CX-400 2.1 0.069 0.157 0.217 0.069 0.059 2.1 0.157 2.25 2.25
0.157 0.069
0.069 0.083 0.089 0.089
0.083
4 0.157 11 Beam- Beam-
CY-100 14.5 11 Beam- Beam- 14.5 14.5 11 emitting receiving 11 14.5
0.571 0.433 emitting receiving 0.433 0.571 0.571 0.433 0.433 0.571
part part part part
EX-10 4.5 0.177 4.5 0.177
EX-20 4.5 4.5
0.177 0.177 4.2 4.2
EX-30 2-ø2.2 ø0.087 2-ø2.2 ø0.087 2-ø2.2 ø0.087 0.165 0.165 2-ø2.2 ø0.087
mounting holes 500 mounting holes
mounting holes 19.685 mounting holes 500
EX-40 19.685
ø2.5 ø0.098 cables
CX-440 15.2 0.598 ø2.5 ø0.098 cables
15.2 0.598
EQ-30
Operation indicator 19.2
(Orange) 0.756 Operation indicator 19.2
EQ-500 38 (Orange) 0.756
1.496 38
MQ-W 1.496
Operation mode switch
RX-LS200 Operation mode switch
ø3.8 ø0.150 cable,
RX ø3.8 ø0.150 cable,
2 m 6.562 ft long
2 m 6.562 ft long
RT-610 1 0.039 8
7 0.315 1 0.039 8
0.276 7 0.315
0.276
 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
290

DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. FIBER
SENSORS

LASER
EX-14□ Sensor SENSORS

PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
13 SENSORS
0.512
6.45 Stability indicator AREA
0.254 SENSORS
2.75 (Green) 3.5
5 0.108 0.138 SAFETY LIGHT
0.197 1.75 Operation 2.1
indicator (Orange) CURTAINS /
0.069 0.083 SAFETY
COMPONENTS
1.75 1.5
0.069 0.059 PRESSURE /
FLOW
SENSORS

INDUCTIVE
4.5 PROXIMITY
Beam- 0.177
11 14.5 SENSORS
receiving
part 0.433 0.571 PARTICULAR
USE
SENSORS
Beam-emitting part 4.5
0.177 SENSOR
OPTIONS
8
0.315 2-ø2.2 ø0.087 mounting holes SIMPLE
WIRE-SAVING
ø2.5 ø0.098 cable, UNITS
2 m 6.562 ft long
WIRE-SAVING
SYSTEMS

MEASURE-
MS-EX10-1 Sensor mounting bracket (Optional) MENT
SENSORS

Assembly dimensions STATIC

CONTROL
DEVICES
t 1.2 7.6 Mounting drawing with EX-14□
t 0.047 0.299 LASER
MARKERS
t 1.2 20 0.787 (0.7)
t 0.047 7.6 (0.028)
PLC
0.299
3.7
0.146 HUMAN
MACHINE
INTERFACES
3.7 3.5 (4.9)
0.146 0.138 (0.193) ENERGY
20 22.75 0.896 MANAGEMENT
0.787 SOLUTIONS
13
4-M2 × 0.4 0.016 6.5 8 3.5 0.512
0.256 0.315 0.138 FA
thru-hole threads 2-ø3.4 ø0.134 mounting holes 5 10.75
0.423
3.5 COMPONENTS
0.197 0.138
Beam- 8 1.25
0.315 (8.8) 0.049 MACHINE
emitting (0.346) VISION
part SYSTEMS
11 8 15
0.433 0.315 0.591 UV
Beam- 3 0.118 11 15 CURING
8 SYSTEMS
receiving 0.315 0.433 0.591
part
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated) 4.25 0.167
Two M2 (length 4 mm 0.157 in) pan head screws are attached.
2-ø3.4 ø0.134 mounting holes
Selection
Guide
Amplifier
Built-in
MS-EX10-2 Sensor mounting bracket (Optional)
Power Supply
Built-in
Assembly dimensions Amplifier-
t 1.2 separated
t 0.047 7.6
0.299 Mounting drawing with EX-11E□ and EX-13E□

6.25 (2.3) EX-Z

7.6 (0.091)
0.246 t 1.2 0.299
t 0.047 CX-400

20 4.5 (7.45) CY-100

6.25
0.787 0.246 0.177 (0.293)
3.2 1.4 EX-10
0.126 0.055 (1.3)
(0.051) 3.2 EX-20
4 0.25 10 0.126 1.25
0.157 0.010 0.394 0.049 EX-30
1.4
11 8 15 0.055 EX-40
0.433 0.315 0.591
Beam- 2.5 0.098 CX-440
15 11 receiving 8
0.591 0.433 0.315 EQ-30
part
2-M2 × 0.4 0.016
thru-hole threads 8 3.5 EQ-500
0.315 0.138 4.25
0.167 MQ-W
Material: Cold rolled carbon steel (SPCC) 8 3.5
(Uni-chrome plated) 0.315 0.138 RX-LS200
20
Two M2 (length 8 mm 0.315 in) pan head screws are attached. 0.787 RX

RT-610
 EX-10 SERIES Ver.2
291 Ultra-slim Photoelectric Sensor

FIBER
SENSORS
DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website.

LASER
SENSORS MS-EX10-3 Sensor mounting bracket (Optional)
PHOTO-
ELECTRIC 15 Assembly dimensions
SENSORS 0.591
MICRO Mounting drawing with EX-14□
PHOTO-
ELECTRIC 7 0.276
SENSORS 10.5 (2.75) 10.8 t 1.2
0.413 (0.108) 0.425 t 0.047
AREA
SENSORS
3.2 (0.7)
1.4 (0.028)
SAFETY LIGHT 0.055 0.126
CURTAINS / 8
SAFETY t 1.2 0.315 4-M2 × 0.4 0.016
COMPONENTS thru-hole threads 3.5 10.5
t 0.047 0.138 0.413 3.2
PRESSURE /
FLOW Beam- 1.75 0.069 Beam- 0.126
13 7
SENSORS receiving part 0.512 emitting part
0.276
10.8 6.5 5 6.25 1.25
INDUCTIVE 0.049
PROXIMITY 0.425 0.256 0.197 0.246 1.4
SENSORS 0.055

PARTICULAR
USE 11 2 3 0.118
SENSORS 0.433 11 15 8
0.079 0.438 0.591 0.315
SENSOR Material: Cold rolled carbon steel (SPCC)
OPTIONS
(Uni-chrome plated) 4.25
SIMPLE Two M2 (length 4 mm 0.157 in) pan head screws and two M2 (length 8 mm 0.315 in) pan 0.167
WIRE-SAVING head screws are attached.
UNITS

WIRE-SAVING
SYSTEMS

MEASURE-
MENT MS-EX10-11 Sensor mounting bracket (Optional)
SENSORS

STATIC Assembly dimensions

CONTROL
DEVICES
Mounting drawing with EX-14□
LASER t 1.2 8.1
MARKERS t 0.047 0.319
20
0.787 (0.7)
t 1.2 8.1
PLC t 0.047 0.319 (0.028)

3.7 (4.9)
HUMAN 20
MACHINE 0.146 (0.193)
INTERFACES 0.787
4-M2 × 0.4 0.016 6.5 8 3.5
3.7 3.5 22.75
thru-hole threads 0.256 0.315 0.138 1.4 3.2 0.896
ENERGY 0.146 0.138
MANAGEMENT 0.055 0.126 13
SOLUTIONS 0.512
5 3.5
0.197 10.75 0.423 0.138
FA 11 8 0.315
COMPONENTS 8 15
0.433 0.315 0.591 (9.3) 3.2 1.25
(0.366)
MACHINE 1.4 0.126 0.049
VISION 0.055
SYSTEMS 3.2 1.4 Beam-emitting part
UV 0.126 0.055
CURING 3 0.118
SYSTEMS 8 11 15
0.315 0.433 0.591
Beam-receiving part
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] are attached. 4.25
1.4
0.055 0.167

Selection
Guide 3.2
0.126
Amplifier
Built-in
Power Supply
Built-in MS-EX10-12 Sensor mounting bracket (Optional)
Amplifier-
separated
t 1.2 8.1 Assembly dimensions
t 0.047 0.319
Mounting drawing with EX-11E□ and EX-13E□
EX-Z
 
6.25 W  
CX-400 0.246 W
CY-100
20   
EX-10 0.787   
1.4
EX-20 0.055 3.2
0.126 

EX-30

    
EX-40 11 8 15    

0.433 0.315 0.591 
CX-440

EQ-30 2-M2 × 0.4 0.016 1.4 %HDP 

thru-hole threads 0.055   
UHFHLYLQJ 
EQ-500 3.2  
0.126 SDUW
MQ-W 8 3.5
0.315 0.138  
RX-LS200 Material: Stainless steel (SUS304)  

Two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached. 
RX  
 
RT-610 

 EX-10 SERIES Ver.2
Ultra-slim Photoelectric Sensor
292

DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. FIBER
SENSORS

LASER
MS-EX10-13 Sensor mounting bracket (Optional) SENSORS

PHOTO-
Assembly dimensions ELECTRIC
SENSORS
7 Mounting drawing with EX-14□ MICRO
10.5 0.276 PHOTO-
0.413 3.2 0.126 ELECTRIC
(2.75) 10.8 t 1.2 SENSORS
1.4 0.055 (0.108) 0.425 t 0.047
1.4 AREA
0.055 3.2 0.126 SENSORS
8 (0.7)
0.315 (0.028) SAFETY LIGHT
15 CURTAINS /
t 1.2 0.591 4-M2 × 0.4 0.016 SAFETY
COMPONENTS
t 0.047 thru-hole threads
PRESSURE /
FLOW
SENSORS

10.8 13 1.75 INDUCTIVE

6.5 0.256 0.512 0.069 3.5
0.425 0.138 PROXIMITY
5 6.25 10.5 SENSORS
0.197 0.246 0.413
1.25 7 PARTICULAR
11 2 0.049 0.276 1.4 3.2 USE
SENSORS
0.433 0.079 Beam-emitting 0.055 0.126
part SENSOR
Material: Stainless steel (SUS304) OPTIONS
3 0.118
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] and two M2 11 15 8
(length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached. Beam-receiving 0.433 0.591 0.315 SIMPLE
part WIRE-SAVING
UNITS

4.25 1.4 WIRE-SAVING

0.167 0.055 SYSTEMS

MEASURE-
3.2 MENT
0.126 SENSORS

STATIC
CONTROL
DEVICES

LASER
MARKERS

PLC

HUMAN
MACHINE
INTERFACES

ENERGY
MANAGEMENT
SOLUTIONS

FA
COMPONENTS

MACHINE
VISION
SYSTEMS

UV
CURING
SYSTEMS

Selection
Guide
Amplifier
Built-in
Power Supply
Built-in
Amplifier-
separated

EX-Z

CX-400

CY-100

EX-10

EX-20

EX-30

EX-40

CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610