Mepc 139

RESOLUTION MEPC.
139(53)
Adopted on 22 July 2005
GUIDELINES FOR THE APPLICATION OF THE REVISED MARPOL ANNEX I
REQUIREMENTS TO FLOATING PRODUCTION, STORAGE AND OFFLOADING
FACILITIES (FPSOs) AND FLOATING STORAGE UNITS (FSUs)
RESOLUTION MEPC.139(53)
REQUIREMENTS TO FLOATING PRODUCTION, STORAGE AND OFFLOADING MEPC 53/24/Add.2
ANNEX 32

THE MARINE ENVIRONMENT PROTECTION COMMITTEE,
RECALLING Article 38(a) of the Convention on the International Maritime Organization

concerning the functions of the Marine Environment Protection Committee (the Committee)
conferred upon it by international conventions for the prevention and control of marine pollution,
NOTING that, at its forty-ninth session, the Committee approved the Guidelines for the
application of MARPOL Annex I requirements for FPSOs and FSUs which were issued as
MEPC/Circ.406 on 10 November 2003,
NOTING ALSO that, at the same session, the Committee recognized that similar
guidelines would be needed for the revised MARPOL Annex I and instructed the Secretariat to
prepare a draft MEPC resolution for the application of the revised MARPOL Annex I
requirements to FPSOs and FSUs,
BEING AWARE that the revised MARPOL Annex I was adopted by

resolution MEPC.117(52) and is expected to enter into force on 1 January 2007,
HAVING CONSIDERED, at its fifty-third session, the recommendation submitted by the

Sub-Committee on Bulk Liquids and Gases to adopt the revised Guidelines, as adapted to the
layout and numbering of the revised MARPOL Annex I,
1. ADOPTS the Guidelines for the application of the revised MARPOL Annex I
requirements to FPSOs and FSUs, the text of which is set out in the Annex to this resolution; and
2. INVITES Governments to apply the Guidelines as soon as the revised Annex I enters into
force.
I:\MEPC\53\24-Add-2.doc
MEPC 53/24/Add.2
ANNEX 32
Page 2
ANNEX

REQUIREMENTS TO FPSOs AND FSUs
1 The Marine Environment Protection Committee, at its forty-ninth session

(14 to 18 July 2003), recognizing the necessity to provide appropriate guidance for the
application of MARPOL Annex I requirements to floating production, storage and offloading
facilities (FPSOs) used for the offshore production and storage of oil, and floating storage units
(FSUs) used for the offshore storage of produced oil, approved the Guidelines for application of
MARPOL Annex I requirements to FPSOs and FSUs. The Guidelines were issued as
MEPC/Circ.406 on 10 November 2003.
2 The Committee, recognizing that similar guidelines would be needed for the revised
MARPOL Annex I, agreed to their adaptation to the new layout and numbering system of the
revised MARPOL Annex I. Thus these Guidelines are intended to replace the Guidelines issued
as MEPC/Circ.406 and it is recommended that contracting Governments give effect to their
provisions as soon as the revised MARPOL Annex I enters into force.
3 The purpose of these Guidelines is to provide for uniform application of the revised
MARPOL Annex I adopted by resolution MEPC117(52) to Floating Production, Storage and
Offloading facilities (FPSOs) and Floating Storage Units (FSUs) that are used for the offshore
production and storage or for offshore storage of produced oil.
4 The Marine Environment Protection Committee, at its forty-ninth session

(14 to 18 July 2003), noted the complex issues involved in applying the requirements of
MARPOL Annex I to FPSOs and FSUs, whose arrangements, functions and operations fall under
the over-riding control of coastal States.
5 In addition, the Committee found that the role of FPSOs and FSUs in operation does not
include transport of oil. Accordingly, FPSOs and FSUs are a form of floating platform and do
not lie within the definition of oil tanker in regulation 1.5 of the revised MARPOL Annex I.
They are therefore subject to the provisions of the revised Annex I that relate to fixed and
floating platforms, including regulation 39.
6 The Committee noted that the environmental hazards associated with the quantities of
produced oil stored on board operational FPSOs and FSUs are similar to some of the hazards
related to oil tankers and that relevant requirements of the revised MARPOL Annex I in relation
to oil tankers could be adapted to address those hazards in an appropriate manner. Based on the
above and recognizing that these floating platforms are stationary when operating, the Committee
recommends that coastal States, flag States and others associated with the design, construction
and operation of FPSOs and FSUs apply the relevant revised MARPOL Annex I regulations
referred to in annex 1 to the Guidelines. References contained in annex 1 relate to the revised
MARPOL Annex I up to and including the amendments contained in resolution MEPC.117(52).
7 These guidelines have been prepared with a view to providing the necessary guidance and
interpretation information which may be specifically applicable to FPSOs and FSUs, and
accordingly represents a single document describing the application of the revised MARPOL
Annex I to these floating platforms.
ANNEX 32
Page 3
8 The provisions of these Guidelines are for application to FPSOs and FSUs when located at
their operating station. However they also take into account the abnormal and rare circumstances of:
.1 voyages for drydocking, repair or maintenance work; or
.2 disconnection of the platform in extreme environmental or emergency conditions.
In either case, the FPSO/FSU should not transport oil to a port or terminal except with the
specific agreement of the flag and relevant coastal States, obtained on a voyage basis. When
undertaking any voyage away from the operating station, for whatever purpose, FPSOs and FSUs
will be required to comply with the discharge provisions of the revised MARPOL Annex I for
oil tankers.
9 In order to avoid development of an entire new text from the revised MARPOL Annex I
attending to such terminology matters and notwithstanding the basis for these Guidelines outlined
above, in any regulation indicated to apply to FPSOs and FSUs by the Guidelines at annex, the
following interpretation of terminology should be used:
.1 “oil tanker” should be read as “FPSO or FSU”;
.2 “carry” should be read as “hold”;
.3 “cargo” should be read as “produced oil and oily mixtures”; and
.4 “voyage” should be read to include “operations”.
10 Oil tanker requirements that are extended by the Guidelines to apply to FPSOs/FSUs are
identified through the phrase “recommend application” or similar, while “applies” is used for
requirements to be implemented irrespective of the contents of this circular.
11 The requirement for oil tankers to undergo the enhanced survey programme
(resolution A.744(18)) was deleted from regulation 13G of MARPOL Annex I by
resolution MEPC.95(46) and its provisions have subsequently been solely given effect through
chapter XI-I of SOLAS. Since SOLAS does not apply to the vast majority of FPSOs and FSUs,
which are permanently moored at their operating stations, the relevant oil tanker requirements of
resolution A.744(18) have been included as one of the provisions of the Guidelines in order to
ensure a satisfactory standard of structural integrity for FPSOs and FSUs. Reflecting the
operational characteristics of FPSOs and FSUs, the Guidelines also make provision for limited
departure from A.744(18) in respect of acceptance of in-water surveys under conditions which do
not compromise safety and pollution prevention.
12 In implementing the provisions of these Guidelines, Member Governments are invited to

use and recognize the Record of Construction and Equipment for FPSOs and FSUs at annex 2 in
place of Forms A and B appended to the revised MARPOL Annex I.
13 The Committee noted that most operations of FPSOs and FSUs are different from other
ships covered by Annex I and, recognizing that the coastal State has jurisdiction over fixed and
floating platforms operating in waters under its jurisdiction, Member Governments may find it
necessary to depart from the provisions of these Guidelines. Accordingly, the Committee invites
Member Governments to advise the Organization of their experience in applying these
Guidelines so that it can be taken into account if future amendments to these Guidelines are
deemed necessary.
MEPC 53/24/Add.2
ANNEX 32
Page 4
ANNEX 1
RECOMMENDED PROVISIONS OF THE REVISED MARPOL ANNEX I FOR

APPLICATION TO FPSOs AND FSUs
Article Subject Basis of Application
Art. 2(3)(b)(ii) Def. Discharge In accordance with Reg. 39 and UI 50, produced water, offshore
processing drainage and displacement water are not included in
the meaning of discharge.
Art. 2(4) Def. Ship FPSOs/FSUs are “fixed or floating platforms” and are therefore
included in this definition.
Regulation Subject Basis of Application

1.1 to 1.4 Defs. Oil, Crude Applies.
Oil, Oily mixture,
Oil fuel
1.5 Def. Oil tanker FPSOs/FSUs are adapted primarily for a purpose other than to
carry (transport) oil and are therefore excluded from this
definition.
1.6 and 1.7 Defs. Crude Oil Not applicable.
tanker, Products
carrier
1.8 Def. Not applicable for same reasons as 1.5.
Combi.carrier
1.9 Def. Major Conversion of an oil tanker or combination carrier to an
conversion FPSO/FSU and vice versa should be considered to be a major
conversion. Alterations or modifications required for an existing
FPSO/FSU to move to another field should not be considered a
major conversion.
1.10 and 1.11 Defs. Nearest Apply.
land, Special
area
1.12 Def. Not applicable to FPSO/FSU at operating station as this
Instantaneous definition applies when the ship is under way (refer regs. 34.1.4
rate of discharge and 31.2, 31.3 and 36.6).
of oil
1.13 to 1.26 Defs. Various Apply.
1.27 Def. Anniversary Applies.
date
1.28.1 and Defs. Ship age Apply.
1.28.2 groups
1.28.3 to 1.28.8 Defs. Oil tanker Not applicable.
age groups
1.29 Def. ppm Applies.
2.1 Application Applies.
ANNEX 32
Page 5

2.2 and 2.3 Application Not applicable as the scope of application of these Guidelines is
for FPSOs and FSUs when located at their normal operational
station, including where appropriate temporary disconnection
from the riser at the operating station for the minimum period
necessary to ensure the safety of the vessel in extreme
environmental or emergency conditions.
2.4 Application Not applicable.
2.5 and 2.6 Existing tankers Not applicable.
engaged in
specific trades
3.1 to 3.3 Exemptions and Any Administration using this clause in relation to FPSOs/FSUs
waivers would need to justify such use in relation to the terms of
paragraph .1 and in accordance with the requirements of
paragraph .3.
3.4 and 3.5 Exemptions and Recommend application in order to sanction the waiver
waivers arrangements outlined in 31.2, eg. for operations within special
areas (3.5.2.1) in compliance with 3.5.2.3 to 3.5.2.6. Transfer of
oily mixtures to offload tankers for discharge ashore is
acceptable within this waiver.
4 Exceptions Applies.
5 Equivalents Applies.
6 Surveys and Applies. Notwithstanding whether SOLAS’74 applies to an
inspections FPSO/FSU, surveys of FPSOs and FSUs should be conducted to
the standard specified for oil tankers in SOLAS’74
regulation 11-2, except for the provisions of 2.2 of Annex B to
resolution A.744(18) as amended in relation to dry-dock survey.
The coastal and flag States may accept bottom survey of the ship
afloat instead of in dry-dock when the conditions are satisfactory
and the proper equipment and suitably qualified personnel are
available.
7 Issue of IOPP Certificate should be issued unless flag and coastal States
certificate have other means of certificating/documenting compliance.
8 Issue of Applicable.
certificate by
another
Government
9 Form of Applicable. When completing the IOPP certificate,
certificate FPSOs’/FSUs’ “type of ship” should be shown as “ship other
than any of the above” and this entry should be annotated with
“FPSO” or “FSU” together with details of operational location.
Record of Construction and Equipment for FPSOs and FSUs
given at Annex 2 should be used for the IOPP Supplement.
Where this is done Form A or Form B required by the
Convention need not be provided.
10 Duration of Applicable.
certificate
MEPC 53/24/Add.2
ANNEX 32
Page 6

11 Port State control Applies to FPSO/FSU at its operating station, recognizing that
on operational under Art. 2(5) and UNCLOS Arts. 56 and 60, the coastal State
requirements exercises sovereign rights for the purposes of exploration and
exploitation of their natural resources. However, port State
control powers are applicable at other times such as if the
FPSO/FSU voyages to a port in another State for maintenance
purposes.
12 Tanks for oil Applicable.
residues (sludge)
13 Standard Applicable.
discharge
connection
14 Oil filtering
Applicable subject to applicable provisions of Reg. 15 and 34.
equipment
For reasons of practicality, the equipment need not be fitted
provided the machinery space discharges are disposed of in
accordance with options a, b, d or e in relation to regulation 15.2.
A waiver may be issued under 14.5.3, where all oily mixtures are
discharged either ashore or into production stream.
15A Discharges In accordance with Reg. 39 and UI 50, applies only to machinery
outside special space discharges and contaminated sea water from operational
areas purposes such as produced oil tank cleaning water, produced oil
tank hydrostatic testing water, water from ballasting of produced
oil tank to carry out inspection by rafting. Since FPSOs/FSUs
and other fixed and floating platforms cannot comply with 15.2.1
when operating on station then these oils and oily mixtures may,
with the agreement of the coastal State:
a. be sent ashore;
b. be incinerated;
c. have water separated and discharged if not exceeding
15ppm oil content under 34.2;
d. be discharged in accordance with this clause subject to
waiver of the en route requirement;
e. be added to the production stream; or
f. be treated using a combination of these methods.
15B Discharges in Applicable, but FPSOs/FSUs cannot comply with 15.3.1 when
special areas operating on station. This requirement should be handled
consistent with 15A above. Coastal State may issue dispensation
from 15.3.1 where satisfied that this dispensation does not
prejudice the environment.
15C and 15D Requirements for Applies.
ships <400GT
and general req.
16.1, 16.2 and Segregation of oil Applies. The principles of 16.3 should be extended to all other
16.4 and water ballast FPSOs and FSUs.
and carriage of
oil in forepeak
tanks
ANNEX 32
Page 7

16.3 " Applies to FPSOs/FSUs which are capable of disconnecting
from the riser at the operating station as collision bulkhead
requirement is in SOLAS rather than MARPOL. This principle
is also relevant to stern collision as per 19.7.
17 Oil Record Book Applies.
Part I
18.1 to 18.9 Segregated Recommend application subject to the conditions listed for 18.2
ballast tanks and 18.3.
18.2 " Not applicable, but FPSO/FSU should have sufficient ballast
capacity to meet stability and strength requirements in design
and operational conditions of loading.
18.3 " Recommend application noting that there should normally be
separation between ballast and produced oil (crude) tanks and
pumping systems, but temporary cross-connection may be
permitted for the duration of transfer operations. In such
exceptional cases where sea water is introduced into produced
oil tanks for the operational purposes listed above in relation to
15.2, it should be dealt with as provided for under that clause.
18.8.1 to 18.8.4 Requirements for Recommend application similar to 18.1 to 18.9.
oil tankers with
dedicated clean
ballast tanks
18.10.1 Existing oil Recommend application to meet 18.2 and 18.3 as modified by
tankers having these Guidelines.
special ballast
arrangements
18.10.2 " Recommended application consistent with 18.3 and 35.2 as
modified by these Guidelines.
18.10.3 " Not applicable.
18.11 SBT for oil Recommend application subject to the conditions listed for 18.2
tankers and 18.3.
>=70,000DWT
delivered after
31.12.79
18.12 to 18.15 Protective Not applicable. Refer 19.3.1 for corresponding provisions in
location of relation to both new purpose-built FPSOs/FSUs and other
segregated ballast non-purpose-built FPSOs/FSUs.
spaces
19 Double hull and Not applicable, except as detailed below.
double bottom
requirements for
oil tankers
delivered on or
after 6.07.96
19.3.1 and " Recommend application to new purpose-built FPSOs/FSUs so as
19.3.6 to provide protection against relatively low-energy collision.
(NOTE: Appropriate measures should also be taken for other
FPSOs/FSUs to address this collision hazard).
MEPC 53/24/Add.2
ANNEX 32
Page 8

19.5 " Applicable to the extent that the Guidelines referred to can be
used to demonstrate equivalency with 19.3.1 and 19.3.6 as
modified above.
19.7 " Recommend application to new construction purpose built
FPSOs/FSUs and other FPSOs/FSUs which are arranged with a
fore peak or collision bulkhead. Similarly, oil should not be held
in integral tanks located at the stern in FPSOs/FSUs which may
offload to a tanker moored astern or alongside of the FPSO/FSU.
19.8 " Recommend application to new construction purpose built
FPSOs/FSUs and other FPSOs/FSUs which may be modified to
meet this regulation.
20 (as amended Double hull and Not applicable.
by resolution double bottom
MEPC.111(50)) requirements for
oil tankers
delivered before
6.07.96
21 Prevention of Not applicable.
pollution from oil
tankers carrying
heavy grade oil as
cargo
22 Pump-room Not applicable.
bottom protection
23 Accidental oil Not applicable.
outflow
performance
24 Damage Recommend application with regard to side damage only. It is
assumptions recommended that protective measures, such as fendering, be
used to minimize side impact damage such as that which might
be experienced during offloading and supply vessel berthing
operations. Such protection, however, should not be considered
to reduce the minimum transverse extent of side penetration
damage.
25 Hypothetical Recommend application for side damages only in accordance
outflow of oil with 24 above.
26 Limitation of size Recommend application based on 24 and 25 above.
and arrangement
of cargo tanks
27 Intact stability Recommend application.
28.1 to 28.5 Subdivision and Recommend application only in respect of side damage in
damage stability accordance with 24 above.
28.6 Damage Not applicable.
assumptions for
oil tankers
>=20,000DWT
delivered on or
after 6.07.96
29 Slop tanks Applies.
ANNEX 32
Page 9

30.1 Pumping, piping Applies, except that manifold is to be provided in at least one
and discharge position on the FPSO/FSU.
arrangement
30.2 " Not applicable for FPSOs.
30.3 to 30.7 " Recommend application, particularly for management of
contaminated sea as per Reg.18.3.
31 Oil discharge Applies only to tank cleanings and contaminated sea water (refer
monitoring and Art. 2(3)(b)(ii), Reg. 39 and UI 50) and should be read in light of
control system Reg. 34. Not required where all oily mixtures are discharged to
shore.
32 Oil/water Applies only to tank cleanings and contaminated sea water (refer
interface detector Art. 2(3)(b)(ii), Reg. 39 and UI 50) and should be read in light of
Reg. 34. Not required where all oily mixtures are discharged to
shore.
33 Crude oil COW system should be fitted unless produced oil characteristics
washing are not suitable for COW.
requirements
34 Control of Applicable as detailed below.
discharge of oil
34.1 Discharges Recommended application whenever the FPSO/FSU is not at its
outside special operating station.
areas
34.2 " Applies.
34.3 to 34.5 Discharges in Applies.
special areas
34.6 Oil tankers Recommend application if FPSO/FSU is less than 150GT.
<150GT
34.7 to 34.9 General Applies.
requirements
35 Crude oil Recommended application to any produced oil tanks used for
washing water ballast as water ballast is subject to different discharge
operations requirements than produced water. COW O&E Manual is to be
provided for any COW system fitted.
36 Oil Record Book Part II should be applied in principle as part of oil production
Part II management system when on station, noting that this function
must be complied with on voyage.
37 SOPEP Applies in respect of SOPEP. However, contingency plan in
accordance with requirements of OPRC Art 3(2) may be
accepted under UI 48 as meeting this requirement. In such cases
a separate SOPEP in accordance with the MARPOL format is
not required. This acceptance of the contingency plan does not
apply to a disconnectable FPSO/FSU unless that plan remains
applicable when the FPSO/FSU is not connected to the riser.
38 Reception FPSOs/FSUs should not be considered as offshore terminals and
facilities should not receive dirty ballast or slops from offload tankers.
39 Special Applies subject to UI 50.
requirements for
fixed or floating
platforms
MEPC 53/24/Add.2
ANNEX 32
Page 10
ANNEX 2
RECORD OF CONSTRUCTION AND EQUIPMENT FOR FPSOs AND FSUs
In respect of the provisions of resolution MEPC.139(53) “Guidelines for application of the

revised MARPOL Annex I2 requirements to FPSOs and FSUs”, hereafter referred to as the
“Guidelines”.
Notes:
1 This form should be used for Floating Production Storage and Offloading facilities
(FPSOs) and Floating Storage Units (FSUs) to which regulation 39 of the revised Annex I
of the Convention applies.
2 This Record should be permanently attached to the IOPP Certificate. The IOPP
Certificate should be available on board the ship at all times.
3 If the language of the original Record is neither English nor French nor Spanish, the text
should include a translation into one of these languages.
4 Entries in boxes shall be made by inserting either a cross (x) for the answers “yes” and
“applicable” or a dash (-) for the answers “no” and “not applicable” as appropriate.
5 Unless otherwise stated, regulations mentioned in this Record refer to regulations of the
revised Annex I of the Convention as implemented under the Guidelines and resolutions
refer to those adopted by the International Maritime Organization.
1. Particulars of ship
1.1 Name of ship .........................................................................................................................
1.2 Distinctive number or letters .................................................................................................
1.3 IMO number (if applicable) ..................................................................................................
1.4 Port of registry (if applicable) ...............................................................................................
1.5 Gross tonnage (if applicable) ................................................................................................
1.6 Produced liquids holding capacity of ship ................................................................... (m3)
1.7 Deadweight of ship ..................................................................... (tonnes) (regulation 1.23)
1.8 Length of ship .................................................................................... (m) (regulation 1.19)
1.9 Operating station (lat/long) ...................................................................................................
1.10 Coastal State ..........................................................................................................................
2
Annex I of International Convention for the Prevention of Pollution from Ships, 1973, as modified by the
Protocol of 1978 relating thereto, hereafter referred to as the “Convention”.
ANNEX 32
Page 11
1.11 Date of build:

1.11.1 Date of building contract ......................................................................................................
1.11.2 Date on which keel was laid or ship was at a similar stage of construction .........................
1.11.3 Date of delivery .....................................................................................................................
1.12 Conversion to FPSO/FSU (if applicable):

1.12.1 Date of conversion contract ..................................................................................................
1.12.2 Date on which conversion was commenced .........................................................................
2. Equipment for the control of oil discharge from machinery space bilges and
oil fuel tanks (regulations 14, 15 and 34)
2.1 Carriage of ballast water in oil fuel tanks:

2.1.1 The ship may under normal conditions carry ballast water in oil fuel tanks □
2.2 Type of oil filtering equipment fitted:

2.2.1 Oil filtering (15 ppm) equipment □
(regulation 14.6)
2.2.2 Oil filtering (15 ppm) equipment with alarm and automatic stopping device
(regulation 14.7) □
2.3 Approval standards:*

2.3.1 The separating/filtering equipment:
.1 has been approved in accordance with resolution A.393(X); □

.2 has been approved in accordance with resolution MEPC.60(33); □
.4 has been approved in accordance with resolution A.233(VII); □
.5 has been approved in accordance with national standards not based
upon resolutions A.393(X) or A.233(VII); □
.6 has not been approved; □
2.3.2 The process unit has been approved in accordance with resolution A.444(XI) □
*
Refer to the Recommendation on international performance and test specifications of oily-water separating
equipment and oil content meters adopted by the Organization on 14 November 1977 by resolution A.393(X),
which superseded resolution A.233(VII); see IMO sales publication IMO-608E. Further reference is made to
the Guidelines and specifications for pollution prevention equipment for machinery space bilges adopted by the
Marine Environment Protection Committee of the Organization by resolution MEPC.60(33), which, effective on
6 July 1993, superseded resolutions A.393(X) and A.444(XI); see IMO sales publication IMO-646E and the
revised Guidelines and specifications for pollution prevention equipment for machinery spaces of ships adopted
by the Marine Environment Protection Committee of the Organization by resolution MEPC.107(49) which,
effectively on 1 January 2005, superseded resolutions MEPC.60(33), A.393(X) and A.444(XI).
MEPC 53/24/Add.2
ANNEX 32
Page 12
2.3.3 The oil content meter:

.1 has been approved in accordance with resolution A.393(X); □
2.4 Maximum throughput of the system is ........................................................................ m3/h
2.5 Waiver of regulation 14:

2.5.1 The requirements of regulations 14.1 and 14.2 are waived in respect of the ship:
.1 As the ship is provided with adequate means for disposal of oily residues
in accordance with the Guidelines □
.2 In accordance with regulation 14.5.1 the ship is engaged exclusively
in operations within special area(s): □
Name of special area(s) .....................................................................
2.5.2 The ship is fitted with holding tank(s) for the total retention on board of all
oily bilge water as follows: □
Tank Tank location Volume

identification (m3)
Frames Lateral position
(from) - (to)
Total volume: ......………..m3
3. Means for retention and disposal of oil residues (sludge) (regulation 12)
and bilge water holding tank(s)*
3.1 The ship is provided with oil residue (sludge) tanks as follows:

identification (m3)
(from) - (to)
*
Bilge water holding tank(s) are not required by the Convention, entries in the table under paragraph 3.3 are
voluntary.
ANNEX 32
Page 13
3.2 Means for the disposal of residues in addition to the provisions of sludge tanks:
3.2.1 Incinerator for oil residues, capacity .....……... l/h □
3.2.2 Auxiliary boiler suitable for burning oil residues □
3.2.3 Tank for mixing oil residues with fuel oil, capacity ........ m3 □
3.2.4 Facility for adding oil residues to production stream □
3.2.5 Other acceptable means: …………………………….. □
3.3 The ship is provided with holding tank(s) for the retention on board of oily bilge
water as follows:

identification (m3)
(from) - (to)
4. Standard discharge connection

(regulation 13)
4.1 The ship is provided with a pipeline for the discharge of residues from machinery
bilges and sludges to reception facilities, fitted with a discharge connection □
5. Construction
(regulations 18, 26 and 28)
5.1 In relation to the application of regulation 18, the ship is:
5.1.1 Provided with SBT □

5.1.2 Provided with COW □
5.1.3 Provided with sufficient ballast capacity to meet stability and strength
requirements □
5.1.4 Provided with CBT
5.2 Segregated ballast tanks (SBT): □

5.2.1 The ship is provided with SBT consistent with regulation 18 □
5.2.2 The ship is provided with SBT which includes tanks or spaces not used for oil
outboard of all produced oil tanks □
MEPC 53/24/Add.2
ANNEX 32
Page 14
5.2.3 SBT are distributed as follows:
Tank Volume (m3) Tank Volume (m3)
Total volume ......... m3
5.3 Dedicated clean ballast tanks (CBT):

5.3.1 The ship is provided with CBT consistent with regulation 18.8 □
5.3.2 CBT are distributed as follows:
Tank Volume (m3) Tank Volume (m3)
Total volume ......... m3
5.3.3 The ship has been supplied with a valid Dedicated Clean Ballast Tank
Operation Manual, which is dated ………....……………………………… □
5.3.4 The ship has common piping and pumping arrangements for ballasting the
CBT and handling produced oil □
5.3.5 The ship has separate independent piping and pumping arrangements for
ballasting the CBT □
5.4 Crude oil washing (COW):

5.4.1 The ship is equipped with a COW system □
5.4.2 The ship is equipped with a COW system consistent with regulations 33 and 35 □
5.4.3 The ship has been supplied with a valid Crude Oil Washing Operations and
Equipment Manual which is dated …………………………………………. □
5.5 Limitation of size and arrangements of produced oil tanks (regulation 26):
5.5.1 The ship is constructed according to the provisions of regulation 26 □
5.6 Subdivision and stability (regulation 28):

5.6.1 The ship is constructed consistent with regulation 28 □
5.6.2 Information and data required under regulation 28.5 have been supplied to the
ship in an approved form □
5.6.3 The ship is constructed consistent with regulation 27 □
ANNEX 32
Page 15
5.7 Double-hull/side construction:
5.7.1 The ship is constructed consistent with regulation 19 as follows:
.1 paragraph 3 (double-hull construction) □

.2 paragraphs 3.1 and 3.6 (double sides) □
.3 paragraph .5 (alternative method approved by the Marine Environment
Protection Committee) □
5.7.2 The ship is constructed consistent with regulation 19.6 (double bottom
requirements) □
6. Retention of oil on board (regulations 29, 31 and 32)
6.1 Oil discharge monitoring and control system:

6.1.1 The ship comes under category ......... oil tanker as defined in
resolution A.496(XII) or A.586(14)∗ (delete as appropriate) □
6.1.2 The system comprises:
.1 control unit □
.2 computing unit □
.3 calculating unit □
6.1.3 The system is:
.1 fitted with a starting interlock □
.2 fitted with automatic stopping device □
6.1.4 The oil content meter is approved under the terms of resolution A.393(X) or
A.586(14) or MEPC.108(49) † (delete as appropriate) suitable for crude oil □
6.1.5 The ship has been supplied with an operations manual for the oil discharge
monitoring and control system □
6.2 Slop tanks:

6.2.1 The ship is provided with ....... dedicated slop tank(s) with the total capacity
of ......... m3, which is. .... % of the oil carrying capacity, in accordance with:
∗
FPSOs and FSUs the keels of which are laid, or which are at a similar stage of construction, on or after
2 October 1986 should be fitted with a system approved under resolution A.586(14); see IMO sales publication
IMO-646E.
†
For oil content meters installed on tankers built prior to 2 October 1986, refer to the Recommendation on
international performance and test specifications for oily-water separating equipment and oil content meters
adopted by the Organization by resolution A.393(X). For oil content meters as part of discharge monitoring and
control systems installed on tankers built on or after 2 October 1986, refer to the Guidelines and specifications
for oil discharge monitoring and control systems for oil tankers adopted by the Organization by
resolution A.586(14); see IMO sales publications IMO-608E and IMO-646E, respectively. For oil content
meters as part of discharge monitoring and control systems installed on oil tankers built on or after
1 January 2005, refer to the revised Guidelines and specifications for oil discharge monitoring and control
systems for oil tankers adopted by the Organization by resolution MEPC.108(49).
MEPC 53/24/Add.2
ANNEX 32
Page 16
.1 regulation 29.2.3 □
.2 regulation 29.2.3.1 □
6.2.2 Produced oil tanks have been designated as slop tanks □
6.3 Oil/water interface detectors:

6.3.1 The ship is provided with oil/water interface detectors approved under the
terms of resolution MEPC.5(XIII) □
6.4 Waiver of regulation:

6.4.1 The requirements of regulations 31 and 32 are waived in respect of the ship as follows:
.1 The ship is engaged exclusively in operations within special area(s)

(regulation 3.5) □
Name of special area(s)……………………………………………………
.2 The ship is provided with adequate means of disposal of contaminated

sea water
a. sent ashore □
b. incinerated □
c. added to the production stream □
7. Pumping, piping and discharge arrangements

(regulation 30)
7.1 The overboard discharge outlets for segregated ballast are located:
7.1.1 Above the waterline □
7.1.2 Below the waterline □
7.2 The overboard discharge outlets, other than the discharge manifold, for clean
ballast are located†:
7.3 The overboard discharge outlets, other than the discharge manifold, for dirty
ballast water or oil-contaminated water from produced oil tank areas are located:
7.3.2 Below the waterline in conjunction with the part flow arrangements
consistent with regulation 30.6.5 □
†
Only those outlets which can be monitored are to be indicated.
ANNEX 32
Page 17
7.4 Discharge of oil from produced oil pumps and oil lines (regulations 30.4
and 30.5):
7.4.1 Means to drain all produced oil pumps and oil lines at the completion of
produced oil discharge:
.1 drainings capable of being discharged to a produced oil tank or slop tank □
.2 for discharge a special small-diameter line is provided □
8. Shipboard oil pollution emergency plan

(regulation 37)
8.1 The ship is provided with a shipboard oil pollution emergency plan in
compliance with regulation 37.1 □
8.2 The ship is provided with an oil pollution emergency plan approved in
accordance with procedures established by ….……………… as the coastal
State in compliance with the unified interpretation of regulation 37.1 □
8.3 The ship is provided with a contingency plan in accordance with requirements
of OPRC Art. 3(2) accepted in accordance with regulation 37 □
9. Surveys
9.1 Records of surveys in accordance with resolution A.744(18), as amended

maintained on board □
9.2 In-water surveys in lieu of dry-docking authorized as per documentation

…………………………………………………………………………… □
10. Equivalents
10.1 Equivalents have been approved by the Administration for certain requirements
of the guidelines on those items listed under paragraph(s) ……………………..
…………………………..………………………………………. of this Record □
MEPC 53/24/Add.2
ANNEX 32
Page 18
THIS IS TO CERTIFY that this Record is correct in all respects.

Issued at …………………………………………………………………………………………
(Place of issue of the Record)
………………………… …………………………………………………………….
(Signature of duly authorized official
issuing the Record)
(Seal or stamp of the issuing authority, as appropriate)
***

Mepc 139

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Mepc 139

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mepc 139

Uploaded by

Copyright:

Available Formats

RESOLUTION MEPC.

Adopted on 22 July 2005

GUIDELINES FOR THE APPLICATION OF THE REVISED MARPOL ANNEX I

THE MARINE ENVIRONMENT PROTECTION COMMITTEE,

RECALLING Article 38(a) of the Convention on the International Maritime Organization

BEING AWARE that the revised MARPOL Annex I was adopted by

HAVING CONSIDERED, at its fifty-third session, the recommendation submitted by the

GUIDELINES FOR THE APPLICATION OF THE REVISED MARPOL ANNEX I

1 The Marine Environment Protection Committee, at its forty-ninth session

4 The Marine Environment Protection Committee, at its forty-ninth session

.1 “oil tanker” should be read as “FPSO or FSU”;

.2 “carry” should be read as “hold”;

.3 “cargo” should be read as “produced oil and oily mixtures”; and

.4 “voyage” should be read to include “operations”.

12 In implementing the provisions of these Guidelines, Member Governments are invited to

RECOMMENDED PROVISIONS OF THE REVISED MARPOL ANNEX I FOR

Article Subject Basis of Application

Regulation Subject Basis of Application

Regulation Subject Basis of Application

Regulation Subject Basis of Application

Regulation Subject Basis of Application

Regulation Subject Basis of Application

Regulation Subject Basis of Application

RECORD OF CONSTRUCTION AND EQUIPMENT FOR FPSOs AND FSUs

In respect of the provisions of resolution MEPC.139(53) “Guidelines for application of the

1.11 Date of build:

1.12 Conversion to FPSO/FSU (if applicable):

2.1 Carriage of ballast water in oil fuel tanks:

2.2 Type of oil filtering equipment fitted:

2.3 Approval standards:*

.1 has been approved in accordance with resolution A.393(X); □

2.3.3 The oil content meter:

2.4 Maximum throughput of the system is ........................................................................ m3/h

2.5 Waiver of regulation 14:

Tank Tank location Volume

Total volume: ......………..m3

Tank Tank location Volume

Total volume: ......………..m3

3.2.4 Facility for adding oil residues to production stream □

3.2.5 Other acceptable means: …………………………….. □

Tank Tank location Volume

Total volume: ......………..m3

4. Standard discharge connection

5.1 In relation to the application of regulation 18, the ship is:

5.1.1 Provided with SBT □

5.2 Segregated ballast tanks (SBT): □

5.2.3 SBT are distributed as follows:

Tank Volume (m3) Tank Volume (m3)

Total volume ......... m3

5.3 Dedicated clean ballast tanks (CBT):

Tank Volume (m3) Tank Volume (m3)

Total volume ......... m3

5.4 Crude oil washing (COW):

5.6 Subdivision and stability (regulation 28):

5.7 Double-hull/side construction:

5.7.1 The ship is constructed consistent with regulation 19 as follows:

.1 paragraph 3 (double-hull construction) □