Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

2010/2011 Critical Care Bed: Maintenance Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 77

IMPORTANT

File in your
maintenance
records

2010/2011 Critical Care Bed


MAINTENANCE MANUAL
For Parts or Technical Assistance
1–800–327–0770
Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning / Caution / Note Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5
Hydraulic System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Base Hood Removal And Reinstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Steer Caster Linkage Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hydraulic Valve/Release Pedal/Spring Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Frame End Removal – Foot End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Replacing Trend/Fowler Display Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Charging Weigh System Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Static Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switch Board/Scale Display/Keyboard Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trend/Fowler Display Board Replacement and Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–14
Scale System Diagnostics And Service
Diagnostic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Displaying Individual Load Cell Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,16
Replacing A Load Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,17
Entering New Load Cell Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17,18
Replacing Scale CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18,19
Activating/Deactivating Serial Option Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19,20
Assembly Drawings and Parts Lists
Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hydraulics Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22–25
Hydraulic Reservoir Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.1
Hood, Base and Caster Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26–30
Basic Litter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Litter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Litter Assembly with Standard Fowler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Fowler Crankscrew Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Emergency Drop Fowler Option Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Emergency Drop Fowler Crankscrew Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Litter Assembly, Basic Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Litter Assembly, Position Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38,39
Litter Assembly, All Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40–42
Litter Assembly, Scale Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43–45
Knee Gatch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Calf Section Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Knee Gatch Crankscrew Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Frame End Assembly, Scale Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Frame End Assembly, Position Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Frame End Assembly, All Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Siderail Assembly, Fold Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Siderail and Bumper Assembly, Left, Fold Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Siderail and Bumper Assembly, Right, Fold Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Siderail Assembly, Fold Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Siderail and Bumper Assembly, Left, Fold Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Siderail and Bumper Assembly, Right, Fold Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Split Folddown Siderail Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Siderail and Bumper Assembly, Split, Left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Siderail and Bumper Assembly, Split, Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Folding I.V. Holder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61, 62
Isolated I.V. Socket Assembly, Standard I.V. Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.1, 62.2
Permanent, Isolated I.V. Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.3
Oxygen Bottle Holder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 64
Defibrillator Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Fowler X–Ray Cassette Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66, 67
Warranty
Obtaining Parts and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Supplemental Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Return Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Freight Damage Claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Introduction

INTRODUCTION
This manual is designed to assist you with the operation and maintenance of the 2010/2011 Stryker Manual
Critical Care Bed. Read it thoroughly before using the equipment or beginning any maintenance on it.

SPECIFICATIONS
Maximum Weight Capacity 500 pounds
Overall Bed Length/Width 90”/38”
Minimum/Maximum Bed Height 22.5”/35”
Knee Gatch Angle 0 degrees to 35 degrees
Fowler Angle 0 to 90 degrees
Trendelenberg/Reverse Trendelenberg –12 degrees to +12 degrees
Weigh System Accuracy (optional equipment) + / – 1% of total patient weight

WARNING / CAUTION / NOTE DEFINITION


The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.

WARNING
The personal safety of the patient or user may be involved. Disregarding this information could result in injury
to the patient or user.

CAUTION
These instructions point out special procedures or precautions that must be followed to avoid damaging the
equipment.

NOTE
This provides special information to make maintenance easier or important instructions clearer.

2
Preventative Maintenance

CLEANING
1. Hand wash all surfaces of the bed with warm water and mild detergent. Dry thoroughly.
2. Clean Velcro AFTER EACH USE. Saturate Velcro with disinfectant and allow disinfectant to evaporate.
(Appropriate disinfectant for nylon Velcro should be determined by the hospital.)

BIANNUAL CHECKLIST
All fasteners secure (reference all assembly prints)
Siderails move and lock properly
All casters lock with brake pedal engaged
Fowler crank operating properly
Knee Gatch crank operating properly
Lift pedal operating properly
Trendelenberg/Reverse Trendelenberg pedals operating properly (page 5 or 8).
Weigh system operating properly (page 15 – 20).
Battery charger operating properly
Head and foot boards secure in frame ends
No cracks or splits in head and foot boards
I.V. pole operating properly
Oxygen bottle holder operating properly
Emergency drop Fowler operating properly
No rips or cracks in mattress cover
Restraint straps and mounting points intact and secure
No leaks at hydraulic connections
No hoses worn, kinked or leaking
Hydraulic oil level sufficient (page 5).
Fowler slide tracks well greased (use MPG2 Dubois or equivalent)
Fowler slides are securely in tracks
Lexan securely fitted – no cracks
No cables worn, frayed or pinched
All electrical connections tight
All grounding cables secure to frame

Serial No.______________
______________
______________
______________
______________

Completed By:_________________________________ Date:_____________

3
Service Information

MECHANICAL TROUBLESHOOTING

PROBLEM/SYMPTOM SOLUTION(S)
Litter will not lower with foot pedals depressed. Adjust valve control linkage rods (page 8).
Litter will not lift when foot pedal pumped. Add hydraulic fluid (page 5).
Bleed air from hydraulic system (page 5).
Change pump pedal cylinder(s).
Litter ”drifts”. Bleed air from hydraulic system (page 5).
Adjust valve control linkage (page 8).
Check for leaking hoses or fittings and replace.
Disconnect hose from affected jack, install cap on
fitting and watch for drift to determine if jack is
faulty.
If jack is O.K., replace the manifold assembly.
Steer wheel doesn’t engage or disengage properly. Adjust steer wheel linkage (page 7).
Replace tension spring.
Emergency Drop Fowler doesn’t crank to full 90 Follow instructions on label located by emergency
degrees. drop cable to reset crank system.

ELECTRICAL TROUBLESHOOTING

PROBLEM/SYMPTOM SOLUTION(S)
Weigh system won’t turn on. Check weigh system lockout switch.
Check voltage from batteries. TP1 (ground) to TP2
should be 18–20 VDC with the power switch
turned on.
Check weigh system switch board.
Replace CPU board (page 18 & 19).
Weigh system shuts off prematurely. Check connections on all weigh cables.
Check individual load cells (page 15 & 16).
Replace scale CPU board (page 18 & 19).
Weigh system readings not accurate. Check all load cells for physical binding on litter
top.
Check individual load cells in diagnostic mode
(page 15 & 16).
Check calibration of load cells (page 17 & 18).
Replace scale CPU board (page 18 & 19).
Trend/Fowler LED board not working. Check power to LED board. TP1 (ground) to TP3
should be 5 VDC (+/– .3) with the power switch
on.
LED Trend/Fowler position lights not accurate. Check potentiometer positions on litter pots and
Trend/Fowler display board (page 13 & 14).

4
Service Information

HYDRAULIC DESCENT RATE ADJUSTMENT


The descent rate of either end of the bed can be adjusted by turning the needle valves on the manifold assem-
blies located on the base of the bed. To access the manifold assemblies, lift and support the foot end of the
hood assembly (see page 6). To slow the jack descent rate, turn the needle valve clockwise. To increase
the jack descent rate, turn the needle valve counterclockwise.

NOTE
The descent rate was preset at the factory.

BLEEDING AIR FROM THE HYDRAULIC SYSTEM


Raise the litter to full up using the lift pedal and continue to pump 10–12 times after full up is reached. Lower
the bed using the foot pedals. While continuing to hold the foot pedals down, pump the lift pedal an additional
10–12 times. Repeat the procedure 2–3 times or until the bed motion is smooth and the pedal action is firm.

CHECKING HYDRAULIC OIL LEVEL


1. Lift and support the base hood (see page 6). The hydraulic oil reservoir is located at the foot end of the
bed on the patient’s left.
2. With all cylinders full up, assure the hydraulic oil is at the required level as indicated on the reservoir.
3. If replacement oil is required, use Mobil Aero HFA or Mobil Aerex 903 hydraulic oil (Stryker part number
2020–70–475).
4. Replace the base hood (see page 6).

5
Service Information

BASE HOOD REMOVAL AND REINSTALLATION

Required Tools:
Phillips Head Screwdriver 5/32” Ball Driver
Bungee Cords or String

Procedure:
1. Raise bed to full up.
2. Remove four Phillips head screws holding hood to base assembly and separate velcro that secures hood
to base tubes.
3. Secure hood to litter using bungee cords, string, etc. so that bed servicing can be easily performed.
4. If more room is needed for service, bellows can be raised above plastic bellows cap. Using a 5/32” Ball
driver, remove two Allen bolts holding bellows cap to jack and remove bellows cap.
5. To reinstall hood after bed service has been completed, remove whatever was used in step 3 to secure
hood to litter and place hood back in correct position on base assembly.
6. Reinstall four Phillips head screws that hold hood to base assembly and press down on hood to secure
velcro holding hood to base tubes.
7. Put bellows and bellows cap onto jack cylinder. Be sure to install caps into ”cutout” groove in jack cylinder.
Reinstall Allen bolts removed in step four and tighten.

8. Put first pleat at top of bellows around bellows cap and tuck bottom of bellows into base hood.

6
Service Information

STEER CASTER LINKAGE ADJUSTMENT

Tools Required:
Phillips Head Screwdriver 3/8” Open End Wrench
5/32” Allen Wrench 1/2” Open End Wrench

F
E
A

Adjustment Procedure:
1. Lift up and support base hood (see page 6).
2. Using a 5/32” Allen wrench and 3/8” open end wrench, remove items (D), (E) and (F).
3. Using a 1/2” open end wrench, loosen jam nut (C).
4. Tighten item (A) into item (B) for more lever engagement or away from item (B) for less engagement.
5. To reassemble linkage, reverse steps 2 and 3.
6. Check steering wheel engagement. When properly adjusted, the locking tab should clear the notch in the
steer caster when in the neutral position, and should fully engage when in steer.
7. After proper adjustment is determined, reinstall base hood.

7
Service Information

HYDRAULIC VALVE/RELEASE PEDAL/SPRING ADJUSTMENT

Required Tools:
3/8” Open End Wrench (2) 7/16” Open End Wrench
Phillips Head Screwdriver

Adjustment Procedure:
1. Lift and support base hood (see page 6).
2. Using a 7/16” open end wrench, adjust pedal stop bumper so that top of pedal is parallel with floor. The
pedal should not be able to raise above this point.
3. After pedal stop bumper has been adjusted properly, manual valve should be closed and litter should stay
firm.
4. If litter does not stay firm, adjustments to the linkage will be required.
5. Depress the pedal to the floor and be sure the return spring is completely bottomed out. If it is not, use
both 3/8” open end wrenches to adjust the ball nut at the pedal end of the linkage rod. Retighten the ball
and jam nut.
6. Release the pedal and adjust the ball nut at the manual valve arm so that there is approximately 1/16 inch
freeplay between the valve arm and the ball nut. Retighten the ball and jam nut.
7. Reinstall the base hood (see page 6).

Washer

Pedal Top to be Parallel


with Floor Line

8
Service Information

FRAME END REMOVAL – FOOT END


If service is required on the electronic portions of the bed, it may be necessary to remove the frame end at
the foot end of the bed.

Required Tools:
Phillips Screwdriver

Removal Procedure:
1. Using the Knee Gatch crank, move Knee Gatch to full up.
2. Remove foot board from receptacles.
3. Using Phillips head screwdriver, remove two Phillips head screws located on front of frame end on frame
end metal bumper.
4. Slowly lift up on frame end at footboard receptacle area and lay frame end on foot of Knee Gatch

CAUTION
Do not lift frame end quickly, electrical cables are attached to frame end.

5. To replace frame end after service is complete, reverse steps 4–2.

9
Service Information

REPLACING TREND/FOWLER DISPLAY OPTION BATTERIES


The Trend/Fowler display option is powered by 3 ”D” size (1.5 V) alkaline batteries. The batteries are located
under the foot end frame end. To replace the batteries, remove the foot end frame end (page 9). Disconnect
the power cable and replace batteries – be sure to note polarity of battery placement on battery holder. The
batteries will need to be replaced when the Trend/Fowler LED angle indicators appear dim.

NOTE
The system power switch under the frame end at the foot end of the bed must be on for the Trend/Fowler
display to light. If the bed is not equipped with a weigh system, there will not be a power switch and the switch
on the keypad must be pressed.

CHARGING WEIGH SYSTEM BATTERIES

CAUTION
Do not charge batteries while they are on the bed.

Required Tools:
Phillips Screwdriver

Procedure:
1. Using Fowler crank, move Fowler up.
2. Remove headboard from receptacles.
3. Using Phillips screwdriver, remove the two Phillips head screws located on front of frame end on frame
end metal bumper.
4. Slowly lift up on frame end at head board receptacle area and lay frame end out of the way.
5. Disconnect the three power cables and remove each battery from the bed by pulling up.
6. Place the battery in an upright position and attach the charger.
7. After batteries have been fully charged, reinstall into the bed.
8. Reconnect the three cables and install the frame end.

* If the batteries are allowed to drain to zero power, it will take 16 hours to completely charge them.

NOTE
When the low battery indicator light on the keypad first lights, there is still enough power to operate the weigh
system for approximately one week.

10
Service Information

STATIC DISCHARGE PRECAUTIONS


The electronic circuits in the 2010/2011 are completely protected from static electricity damage only while
the bed is assembled. It is extremely important that all service personnel always use adequate static protec-
tion when servicing the electronic systems of the 2010/2011. Whenever you are touching wires, you should
be using static protection.

Static Protection Equipment


The necessary equipment for proper static protection is:
S 1 static wrist strap; 3M part number 2214 or equivalent,
S 1 grounding plug; 3M part number 61038 or equivalent,
S 1 test lead with a banana plug on one end and an alligator clip on the other; Smith part number
N132B699 or equivalent.

CAUTION
All electronic service parts will be shipped in static shielding bags. Do not open the bags until you have com-
pleted the following procedure. Do not place unprotected circuit boards on the floor. All circuit boards to be
returned to Stryker Medical should be shipped in the static shielding bags the new boards were shipped in.

Static Protection Procedure


1. Insert the grounding plug into a properly grounded hospital grade wall receptacle. Plug the banana plug
of the test lead into the receptacle on the grounding plug. Connect the alligator clip on the other end of
the test lead to the ground chain of the bed.

2. Place the static control wrist strap on your wrist. Connect the alligator clip at the other end of the wrist strap
cord to the ground chain of the bed.

BED

GROUNDING DIAGRAM

11
Service Information

SWITCH BOARD (SYSTEM ON) AND/OR SCALE DISPLAY/KEYBOARD REPLACEMENT

Required Tools:
Phillips Screwdriver
1/4” Nut Driver

Replacement Procedure:
1. Properly ground yourself (see page 11 for static discharge precautions).
2. Remove the foot end frame end from the litter (page 9).
3. Carefully remove the cable attached to the board.
4. Using a 1/4” nut driver, remove the four nuts holding the board to the frame end and remove the defective
board.
5. Install new board and reattach the 4 nuts and cable.
6. Replace the frame end.
7. Check all operations before returning the bed to service.

TREND/FOWLER DISPLAY BOARD REPLACEMENT


Required Tools:
Phillips Screwdriver
Small (Jeweler’s) Screwdriver
1/4” Nut Driver

Replacement Procedure:
1. Properly ground yourself (see page 11 for static discharge precautions).
2. Remove the foot end frame end from the litter (page 9).
3. Carefully remove the 3 cables attached to the board.
4. Using a 1/4” nut driver, remove the four nuts holding the board to the frame end and remove the defective
board.
5. Install new board and reattach the 4 nuts and cable.
6. Important: follow the alignment procedure on page 13.
7. After completing the alignment procedures, replace frame end.
8. Check all operations before returning the bed to service.

12
Service Information

TREND/FOWLER DISPLAY BOARD ALIGNMENT

Required Tools:
3/32 Allen Wrench Small Needle–Nosed Pliers
Inclinometer or Protractor Thread Lock Compound
Red Lacquer Jumper
Digital VOM, Fluke 77 or Equivalent Flat Blade Jeweler’s Screwdriver or Potentiometer
Adjustment Tool

FOWLER DISPLAY ALIGNMENT PROCEDURE:

Mechanical Alignment of the Fowler Pot Shaft


NOTE
The Fowler potentiometer shaft is located under the litter midsection on the patient’s right side.

1. Loosen set screws securing Fowler pot shaft to linkage arm.


2. Using Fowler crank, lower the Fowler to flat (0 degrees).
3. Unplug the Fowler pot cable. Using a digital VOM, measure the resistance between the green and black
wires. Using small needle–nosed pliers, turn the Fowler pot so that the resistance is 75 ohms +/– 3 ohms.
4. Tighten the set screws on the Fowler pot shaft and recheck the resistance measurement. Readjust as
required.
5. Reconnect the Fowler pot cable assembly.

CAUTION
The material of the potentiometer shaft is brass and care should be taken not to tighten the set screws too
firmly. Once all the calibrations are complete and the system is set, the set screw can be tightened securely.

Electrical Alignment of the Fowler Display Board


1. Complete the mechanical alignment procedure above.
2. Raise Fowler fully (90 degrees).
3. Remove foot end frame end. Turn bed power on and position frame end so the Fowler angle display is
visible.
NOTE
The system is normally powered by a momentary button. To power the system continuously, place a jumper
from the cathode of D1 to the R8–R4 node.
4. Adjust R5 on the display board so that the 90 degree Fowler LED is on. Adjust R5 back and forth so that
it is positioned in the center of the range that keeps the 90 degree LED on (normally 1 1/2 turns past the
point when the 90 degree LED comes on).
5. Raise and lower the Fowler while checking the angle with an inclinometer. Adjust R5 as required for angle
accuracy. The resistance of the Fowler pot when the Fowler is at 90 degrees is approximately 417 ohms
(reference only).

When all calibration is complete, secure all set screws with thread lock compound and paint the potentiometer
adjustment slot (R5) with red lacquer.

13
Service Information

TREND/FOWLER DISPLAY BOARD ALIGNMENT (CONTINUED)

TREND DISPLAY ALIGNMENT PROCEDURE:

Mechanical Alignment of the Trend Pot Linkage

NOTE
The Trend potentiometer linkage is located under the frame end at the patient’s head, on the left side.

1. Loosen set screws securing Trend pot shaft to linkage arm.


2. Using the foot pedals, raise the bed fully and level the litter to 0 degrees.
3. Unplug the trend pot cable assembly and measure the resistance between the green and black wires.
Adjust the pot, using a jewellers screwdriver, to approximately 86 ohms (+/– 3 ohms). Secure set screws
and check resistance. Readjust as required.

Electrical Alignment of the Trend Display Board

1. Complete the mechanical procedure above.


2. Using the foot pedals, raise the bed fully and put the litter into full Trendelenberg (head down).
3. Remove foot end frame end. Turn bed power on and position frame end so the Trend angle display is vis-
ible.

NOTE
The system is normally powered by a momentary button. To power the system continuously, place the jumper
from the cathode of D1 to the R8–R4 node.

4. Adjust R1 on the display board so that the +12 degree LED is on. Adjust R1 back and forth so that it is
positioned in the center of the range that keeps the +12 degree LED on. Normally this is 1 turn past when
the +12 degree LED is first on.
5. Position bed at various trend angles and check the angle with an inclinometer. Adjust R1 as required for
accuracy of the LED lights. The resistance measurement for 0 degrees is 86 ohms. For +12 degrees,
the measurement is 129 ohms and for –12 degrees it is 46 ohms (reference only).

When all calibration is complete, secure all set screws with thread lock compound and paint the potentiometer
adjustment slots (R1 and R5) with red lacquer.

14
Service Information

SCALE SYSTEM DIAGNOSTICS AND SERVICE


Diagnostic Mode Functions:
1. Download Barcode: This is a factory set–up mode and is not used in the field.
2. Calibrate Scale: This may be required in the field if replacement of several load cell assemblies or of the
scale CPU is required. Replacement of a single load cell assembly does not normally require this proce-
dure.
3. Change LBS/Volts: This is required whenever a load cell assembly or a scale CPU is changed in the field.
4. Change Ref. Volts: This is a factory set–up mode and is not used in the field.
5. Init. to Defaults: This may be required in the field when replacing the scale CPU board.
6. Display Corner: This function displays the individual corner weights for each load cell assembly and can
be used to isolate a defective load cell.
7. Serial Option (If so equipped): This enables the scale system remote display port.
8. Quit/Save: This exits the diagnostic mode. Changes made in the diagnostic mode (with the exception of
Calibrate Scale) must be saved in permanent memory using this function. Quitting without saving will reset
all variables to their previous values, as will switching off bed power without using the save function.

Diagnostic Mode:
1. To enter diagnostic mode, remove power from the scale system by switching the scale power switch toward
the foot of the bed.
2. Press and hold down the LBS/KGS key.
3. While still holding the LBS/KGS key, switch the scale power switch toward the head of the bed.
4. After two seconds, release the LBS/KGS key. The scale monitor should read DOWNLOAD BARCODE.
The diagnostic mode is now active.
Special Key Functions in the Diagnostic Mode:
1. The four keys on the left side of the green scale key grouping function as POSITION keys, corresponding
with the four corners of the bed litter. Whenever the scale monitor displays ”PICK CORNER NOW”, press
one of these keys to select the load cell assembly at the desired corner.
a. ZERO BED = Head end, patient’s right side.
b. ZERO/GAIN LOSS = Foot end, patient’s right side.
c. CHANGE EQUIP. START = Head end, patient’s left side.
d. CHANGE EQUIP. FINISH = Foot end, patient’s left side.

Displaying Individual Load Cell Outputs:


A faulty load cell can be detected by entering diagnostics and displaying individual load cell outputs.
1. Enter the diagnostic mode. The scale monitor will display DOWNLOAD BARCODE when the diagnostic
mode is active.
2. Press and release LBS/KGS until the scale monitor displays DISPLAY CORNER.
3. Press and release WEIGHT SYSTEM ON. The scale monitor should display PICK CORNER NOW.
4. Press and release the position key that corresponds with the load cell to be checked. The scale monitor
should display XX=NNN.N. ”XX” represents the initials of the selected corner, i.e. H/R will be displayed
for the patient’s head end, right side. ”NNN.N” represents the actual weight load on the load cell.
5. Repeat step four for each corner. Head end weight readings will normally be lower than foot end weights.
Weight readings should be constant. A jumpy, drifting 000.0 or 999.9 weight indicates a problem with the
selected load cell assembly or load cell cable.

15
Service Information

Displaying Individual Load Cell Outputs (Continued):


6. When all the load cell outputs have been checked, press and release WEIGHT SYSTEM ON.
7. Press and release LBS/KGS until the scale monitor displays QUIT/SAVE.
8. Press and release WEIGHT SYSTEM ON. The scale monitor should shut off after one second.

Replacing a Load Cell:

Required Tools:
3/16” Allen Socket 10 Ft. Lb. Torque Wrench
Saw Horse(s) 3M Static Protection
5/64” Allen Wrench Pencil

Replacement Procedure:
1. Properly ground yourself (see page 11 for static discharge precautions).
2. Using a 5/64” Allen wrench, remove the two cap screws holding the plastic cover to the load cell mounting
block.
3. Disconnect the cable from the load cell.

16
Service Information

Load Cell Replacement Procedure (Continued):


4. Using a pencil, draw a line on the underside of the litter crossbar along the end of the load cell mounting
block to use for reference when installing the new load cell (see illustration).

5. Using blocks, sawhorses, etc., support the litter under the frame end at the end of the bed where the load
cell is being removed.
6. Using a 3/16 Allen socket, remove the two cap screws holding the load cell assembly to the litter support
bar.
7. Pull the load cell out of the mounting block. Do not lose the nylon spacer between the load cell and the
stop pin. It is used with the new load cell.
NOTE
Metal shims are used when shipping new load cell assemblies. Remove and discard these shims after instal-
ling the new load cell.
8. Install the new load cell being sure to have the strain gauge facing down. The strain gauge should be visible
through the slot in the load cell mounting block or the scale readings will be incorrect.
9. Line up the end of the load cell mounting block with the line drawn on the underside of the litter crossbar.
Install the two cap screws and tighten them to 8–10 foot–pounds torque.
10. Connect the cable to the weigh board and reattach the plastic cover to the load cell mounting block. The
new bar codes must now be entered in the memory.
Entering New Load Cell Bar Codes:
1. Enter diagnostic mode. The scale monitor will display DOWNLOAD BARCODE when the diagnostic mode
is active. Press and release LBS/KGS two times. The scale monitor should display CHANGE LBS/
VOLTS. Press and release WEIGHT SYSTEM ON. The scale monitor should display PICK CORNER
NOW. Press and release the position key that corresponds with the replaced load cell. For example, if
the patient’s head end, right side load cell has been replaced, press and release the ZERO BED key.
2. Using the LBS/KGS key to position the brackets around the digit that is to be changed and using the LOCK/
UNLOCK key to change the bracketed digit, change the displayed number to match the number printed
on the new load cell assembly’s bar code. For example, the scale monitor might display H/R LV= <8>7811.
Assuming the new load cell assembly bar code label reads L92101, the procedure to change the displayed
number would be as follows:
a. Press and release LOCK/UNLOCK one time. The scale monitor should display H/R LV=<9>7811.
b. Press and release LBS/KGS one time. The scale monitor should display H/R LV=9<7>811.
c. Press and release LOCK/UNLOCK one time. The scale monitor should display H/R LV=9<8>811. Repeat
this step four more times, until the display reads H/R LV=9<2>811.
d. Press and release LOCK/UNLOCK one time. The scale monitor should display H/R LV=92<8>11.
e. Press and release LBS/KGS three times. The scale monitor should display H/R LV=92<1>11.
f. Press and release LOCK/UNLOCK one time. The scale monitor should display H/R LV=921<1>1.
g. Press and release LBS/KGS nine times. The scale monitor should display H/R LV=921<0>1.

17
Service Information

Entering New Load Cell Bar Codes (Continued):


3. Press and release WEIGHT SYSTEM ON. The scale monitor should display PICK CORNER NOW.
4. Press and release WEIGHT SYSTEM ON. The scale monitor should display CHANGE LBS/VOLTS.
5. Press and release LBS/KGS until the scale monitor displays QUIT/SAVE.
6. Press and continue to hold WEIGHT SYSTEM ON until the scale monitor displays HOLD TO SAVE and
then displays SAVE COMPLETE. Remember, the save function must be completed or the numbers will
reset to the previous values.
7. Release WEIGHT SYSTEM ON. The scale monitor will go blank in one second. The scale system will
now operate normally. Check the weigh system accuracy before returning the bed to service.

Replacing Scale CPU:

Required Tools:
Phillips Head Screwdriver
Small Screwdriver
Replacement Procedure:
1. Properly ground yourself (see page 11 for static discharge precautions).
2. Remove the foot end frame end from the litter (see page 9 for instructions).
3. Remove the connectors from the scale CPU circuit board (see illustration). Note the orientation and place-
ment of the connectors so they will be attached properly to the new scale CPU board.

Switch/LED System
Cable – to JP6 on
Scale CPU

Power System
Cable

Ground Wire –
to P1 on
Scale CPU

Weigh System Cable –


Drain Wire to JP3 on Scale CPU

Scale Cable Assembly

SWITCH BOARD LCD/DISPLAY KEYPAD


CIRCUIT BOARD

4. Using a small screwdriver, remove the six screws holding the scale CPU board and carefully remove the
CPU board from the spacers on the litter computer plate.
5. Place the new scale CPU board over the spacers and reinstall the four screws.
6. Attach the connectors to the scale CPU board. Be sure to orient the connectors properly.

18
Service Information

Replacing Scale CPU (Continued):


7. Reinstall the frame end (see page 9).
8. Place the new CPU board in diagnostics mode.
9. Press and hold LBS/KGS until the scale monitor displays INIT TO DEFAULTS.
10. Press and continue to hold WEIGHT SYSTEM ON until the scale monitor displays HOLD TO CHANGE
and then displays DEFAULTS ENTERED.
11. Press and release LBS/KGS until the scale monitor displays CHANGE LBS/VOLTS.
12. Follow the steps outlined previously under ”Entering New Load Cell Bar Codes” to enter the bar code num-
bers for all four load cells. It is not necessary to SAVE after each entry. Instead, at step 3, when the monitor
displays PICK CORNER NOW, select another corner with the proper position key. After all four corners
have been entered, SAVE the results as described in steps 5 and 6. DO NOT FORGET TO SAVE OR
THE NUMBERS WILL HAVE TO BE ENTERED AGAIN!!
13. Turn on the scale system and zero the bed, following the displayed instructions.
14. Place a known weight on the center of the bed; the heavier the better, and no less than 25 pounds. The
displayed weight should be within 1% of the actual weight.
15. If the displayed weight is not accurate, use the following procedure to calibrate the scale:
a. Remove the weight from the bed place the scale CPU in diagnostics mode.
b. Press and release LBS/KGS until the scale monitor displays CALIBRATE SCALE.
c. Press and hold WEIGHT SYSTEM ON. Zero the bed, following the displayed instructions. When the
bed is zeroed, the scale monitor should display REF X100=<2>000.
d. The displayed number must now be changed to match the known weight (from step 15) times 100. For
example, if you weighed yourself on a known good scale and you weigh 192.4 pounds, you would change
the REF number to equal 19240. Change the REF number using the procedure outlined previously
under ”Replacement of Load Cell Assemblies” i.e., use the LBS/KGS key to position the brackets around
the digit needing to be changed, and the ”LOCK/UNLOCK” key to change the bracketed digit.
e. After the number is corrected, press and release WEIGHT SYSTEM ON. The scale monitor should
display ADD LBS, HIT ON.
f. Place the weight used previously on the center of the bed and press and hold WEIGHT SYSTEM ON.
The scale monitor should display RELEASE TO CAL.
g. Release WEIGHT SYSTEM ON. The scale monitor should display DO NOT TOUCH BED. Don’t touch
the bed. When calibration is complete, the scale monitor should display CALIBRATE SCALE.
h. Press and release LBS/KGS until the scale monitor displays QUIT/SAVE.
i. Press and release WEIGHT SYSTEM ON. The scale monitor should shut off after one second.
j. Installation is now complete. Re–zero the empty bed and check the scale accuracy with the weight used
previously.

Activating/Deactivating Serial Option Mode:


To enter the serial option mode:
1. Enter the diagnostic mode. The scale monitor will display DOWNLOAD BARCODE when the diagnostic
mode is active.
2. Press and release LBS/KGS six times. The scale monitor should display SERIAL OPTION.
3. Press and release WEIGHT SYSTEM ON. The scale monitor should display SERIAL PORT ON or SE-
RIAL PORT OFF depending on the current set–up.
4. Press and release LOCK/UNLOCK one time to toggle the Serial Port option on or off.
5. Press and release WEIGHT SYSTEM ON. The scale monitor should display SERIAL OPTION.
6. Press and release LBS/KGS until the scale monitor displays QUIT/SAVE.

19
Service Information

Activating/Deactivating Serial Option Mode (Continued):


7. Press and hold WEIGHT SYSTEM ON. The scale monitor should display HOLD TO SAVE. Continue to
hold WEIGHT SYSTEM on until the scale monitor displays SAVE COMPLETE.
8. Release WEIGHT SYSTEM ON. The scale monitor will go blank after one second. The scale system will
now operate normally.

Serial Port Parameters


1. Normal bed function is not affected by the serial port, although some key response delays may be noted
when the serial port option is on. When on, the serial port transmits continuously whether the scale monitor
is on or off. Transmission pauses during ZERO BED, ZERO GAIN/LOSS, or CHANGE EQUIPMENT
functions.
2. Default serial port mode is 9600 Baud, no parity, 8 data bits, 1 stop bit. Default string terminator is CR/LF.
Transmitted data is identical to that displayed on the scale monitor.
3. Data transmit rate default is the same as the bed weight sample rate, or approximately once per second.
Sample rate will vary slightly with the weight on the bed, and will slow down when the scale monitor is on.
No handshake is provided, although the transmit rate is variable with some port options.

20
2010–1–210 Base Assembly

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2222–1–217 Base Tube Assembly 1 AD 938–1–75 Guide, Brake Shaft 4
B 2020–1–270 Caster Tube Ass’y, Ft. 1 AE 38–97 Spring 4
C 2020–1–271 Caster Tube Ass’y, Hd. 1 AF 721–40–25 Pedal 3
D 2020–1–394 Brake Rod Ass’y, Foot 1 AH 14–2 Washer 8
E 958–1–231 Cam Bushing 4 AJ 16–6 Kep Nut 6
F 2020–1–389 Cam, Machined 2 AK 3–67 Hex Hd. Cap Screw 3
H 2020–1–386 Brk. Arm & Shaft Ass’y 1 AL 16–2 Fiberlock Nut 4
J 716–1–275 Brake Pedal 2 AM 2020–1–268 Pillow Block Bearing 2
K 2020–1–390 Brake Arm Conn. Link 1 AN 2020–1–366 Pump Bar & Shaft Ass’y 1
L 2020–1–358 Cam Pad 2 AP 390–1–176 Grounding Chain 1
M 2020–1–370 Pedal Lever Ass’y 2 AR 3–68 Hex Hd. Cap Screw 4
N 715–1–165 Actuator Plate Ass’y 1 AS 26–169 Groove Pin 1
P 2020–1–395 Hd. End Brake Rod 1 AT 37–11 Neoprene Cap 2
R 2020–1–250 Cylinder Oper. Lever, Rt. 1 AW 3–79 Hex Hd. Cap Screw 1
S 28–56 Retaining Ring 2 AY 3–4 Hex Hd. Cap Screw 2
T 4–9 Soc. Hd. Cap Screw 4 AZ 26–196 Groove Pin 2
W 2020–1–357 Brake Bar Assembly 2 BA 8–21 Shoulder Bolt 1
Y 16–12 Flexlock Nut 4 BB 15–22 Hex Nut 2
Z 8–17 Shoulder Bolt 3 BC 16–36 Nylock Nut 4
AA 3–87 Hex Hd. Cap Screw 4 BD 2020–46–225 Brake Link Ass’y 1
AB 11–4 Flat Washer 4 BE 11–193 Flat Washer 10
AC 26–14 Roll Pin 1 BF 2020–46–228 Threaded Brake Link 1
BH 15–32 Jam Nut 1

21
2010–70–210 Hydraulics Base Assembly

22
2010–70–210 Hydraulics Base Assembly
Item Part No. Part Name Qty.
A (page 21) Base Assembly 1
B 2020–70–430* Cylinder Assembly 2
C 2020–70–495 Oil Filter Assembly 1
D 2020–1–297 Linkage Bar, Short 1
E 2010–70–212 Manifold Ass’y, Foot 1
F 2010–70–213 Manifold Ass’y, Head 1
H 2020–1–346 Fitting Guard Ass’y 2
J (page 25.1) Reservoir Assembly 1
K 2020–1–298 Linkage Bar, Long 1
L 2020–70–479 Hydraulics Pan Ass’y 1
M 2020–70–459 Cylinder Ass’y, Right 1
N 2020–70–498 Cylinder Ass’y, Left 1
P 2020–1–323 Spacer 2
R 11–134 Washer 2
S 3–75 Hex Hd. Cap Screw 2
T 38–223 Extension Spring 1
W 2020–1–265 Modified Nut 6
Y 11–33 Shim Washer 6
Z 38–210 Compression Spring 2
AA 3–71 Hex Hd. Cap Screw 8
AB 3–23 Hex Hd. Cap Screw 4
AC 11–1 Washer 2
AD 15–4 Hex Nut 4
AE 26–131 Clevis Pin 2
AF 2020–70–465 Hydraulic Hose 2
AH 2020–70–492 Hydraulic Hose 1
AJ 3–84 Hex Hd. Cap Screw 1
AK 2020–70–499 Hydraulic Hose 1
AL 2020–70–445 Hydraulic Hose 2
AM 2020–70–446 Hydraulic Hose 2
AN 2020–70–447 Hydraulic Hose 1
AP 2020–70–464 Hydraulic Hose 1
AR 2020–70–490 Hydraulic Hose 1
AS 15–22 Jam Nut 1
AT 2020–70–444 Hydraulic Hose 1
AY 958–70–461 Hydraulic Hose 1
AZ 48–84 Y–Connector 1
BA 38–182 Hose Clamp 12
BB 38–192 Hose Clamp 14
BC 26–132 Clevis Pin 2
BD 27–9 Hair Pin Cotter 4
BE 11–14 Washer 8
BF 16–11 Fiberlock Nut 3
BH 52–79 Snap Bushing 2
BJ 16–28 Fiberlock Nut 8
BK 11–2 Washer 16
BL 4–9 Soc. Hd. Cap Screw 2
BM 16–40 Fiberlock Nut 8
BN 15–12 Nut 4
BP 3–5 Hex Hd. Cap Screw 2
BR 11–193 Washer 2
BS 16–11 Washer 2

*When Low Height Bed option is present, use p/n 2020–20–311, cylinder assembly, qty. 2.

23
2010–70–210 Hydraulics Base Assembly

24
2010–70–210 Hydraulics Base Assembly

25
2010–70–236 Hydraulic Reservoir Assembly

Item Part No. Part Name Qty.


A 2010–70–226 Reservoir 1
B 48–123 Bushed Mount Elbow 1
C 48–96 Straight Threadless Connector 2
D 48–92 Bushing 6
E 48–93 Straight Threadless Connector 3
F 37–48 Cap 1
H 45–35 Gasket 1
J 2020–70–437 Label 1

25.1
Notes

25.2
2010–1–310 Hood, Base and Caster Assembly

Litter/Base Ground Wire


P/N 2010–1–212

26
2010–1–310 Hood, Base and Caster Assembly
Item Part No. Part Name Qty.
A (page 22–25) Hydraulics Base Ass’y 1
B 2020–1–213 Hood Assembly 1
C 2010–1–101 Label, Foot End 1
D 2020–1–135 Label, Brake/Steer, Hd. 1
E 2010–1–102 Specification Label 1
F 2010–1–103 Label, Logo, Left 1
H 7–17 Truss Hd. Mach. Screw 4
J 946–1–60 Stryker Logo Label 2
K 2010–1–211 Hood Plug 1
L 11–221 Washer 4
M 1000–59–10 Steer Latch Assembly 1
N * Bellows 2
P 946–1–115 Grommet 4
R 29–7 Dual Lock 2
S 29–9 Dual Lock 2
T 4–8 Soc. Hd. Cap Screw 5
W 2020–1–352 Bellows Cap 2
Y 2020–1–350 Bellows Cap 2
Z 2010–1–104 Label, Logo, Right 1
AA 16–33 Fiberlock Nut 1
AB 946–1–276 Caster Assembly 4
AC 715–1–158 Caster Nut 4
AD 2020–46–218 Linkage Bar, Rt. 1
AE 26–5 Roll Pin 4
AF 38–211 Compression Spring 1
AH 8–21 Shoulder Bolt 1
AJ 14–4 Nylon Washer 1
AK 2020–46–215 Linkage Bar Ass’y 1
AL 14–2 Nylon Washer 5
AM 16–2 Fiberlock Nut 1
AN 13–18 Ext. Tooth Lock Washer 2
AP 2011–1–215 Grounding Lug 1
AT 13–38 Ext. Tooth Lock Washer 4
AW 2011–1–104 Label, Warning 1
AZ 15–32 Jam Nut 1
BA 2020–1–160 Date–of–Manufacture Label 1

* For a standard height base, use bellows part number 2020–1–275.


* For a low height base, use bellows part number 958–1–214.

27
2011–1–310 Hood, Base and Caster Assembly

28
2011–1–310 Hood, Base and Caster Assembly

Item Part No. Part Name Qty.


A (page 22–25) Hydraulics Base Ass’y 1
B 2020–1–213 Hood Assembly 1
C 2011–1–101 Label, Foot End 1
D 2011–1–110 Label, Brake/Steer, Hd. 1
E 2011–1–111 Specification Label 1
F 2011–1–102 Label, Logo, Left 1
H 7–17 Truss Hd. Mach. Screw 4
J 946–1–60 Stryker Logo Label 2
K 2010–1–211 Hood Plug 1
L 11–221 Washer 4
M 1000–59–10 Steer Latch Assembly 1
N 15–32 Jam Nut 1
P 946–1–115 Grommet 4
R 29–7 Dual Lock 2
S 29–9 Dual Lock 2
T 4–8 Soc. Hd. Cap Screw 5
W 2020–1–352 Bellows Cap 2
Y 2020–1–350 Bellows Cap 2
Z 2011–1–103 Label, Logo, Right 1
AA 16–3 Fiberlock Nut 1
AB 390–1–275 Caster Ass’y, Carpet 4
AC 715–1–158 Caster Nut 4
AD 2020–46–218 Linkage Bar, Rt. 1
AE 26–5 Roll Pin 4
AF 38–211 Compression Spring 1
AH 8–21 Shoulder Bolt 1
AJ 14–4 Nylon Washer 1
AK 2020–46–215 Linkage Bar Ass’y 1
AL 14–2 Nylon Washer 5
AM 16–2 Fiberlock Nut 1
AN 13–10 Ext. Tooth Lock Washer 2
AP 2011–1–215 Grounding Lug 1
AR 36–46 Grounding Label 1
AS 988–2–676 Grounding Cable 2
AT 25–54 Pop Rivet 5
AW 13–17 Ext. Tooth Lock Washer 5
AY 13–18 Ext. Tooth Lock Washer 4
AZ 460–2–32 Grounding Strap 2
BA 2010–1–160 Date–of–Manufacture Label 1
BB 2011–1–125 Label, GS 1
BC 2011–1–104 Label, Warning 1
BD 4–21 Soc. Hd. Cap Screw 2
BE 2010–1–213 Ground Lug Bracket 1
BF 13–38 Ext. Tooth Lock Washer 6
BH 16–33 Fiberlock Nut 3
BJ 36–115 Label 1
BK * Bellows 2

* For a standard height base, use bellows part number 2020–1–275.


* For a low height base, use bellows part number 958–1–214.

29
2011–1–310 Hood, Base and Caster Assembly

GROUNDING DIAGRAMS

p/n 25–54, Pop Rivet, Item AT


p/n 460–2–32
p/n 13–17 Ext. Th. Lock Washer, Item AW Ground Strap
Item AZ p/n 25–54, Pop Rivet, Item AT

p/n 13–17 Ext. Th. Lock Washer, Item AW

Head End Grounding Scheme on Brake Mechanism

p/n 25–54, Pop Rivet, Item AT


p/n 13–17 Ext. Th. Lock Washer, Item AW
p/n 460–2–32
Ground Strap
Item AZ
p/n 460–2–32, Ground Strap, Item AZ

p/n 25–54, Pop Rivet, Item AT p/n 25–54, Pop Rivet, Item AT

p/n 13–17 Ext. Th. Lock Washer, Item AW p/n 13–17 Ext. Th. Lock Washer, Item AW

Ground Cable
p/n 25–54 p/n 988–2–676
Pop Rivet Item AS
Item AT
p/n 13–17
Ext. Th. Lock Washer
Item AW

Foot End Grounding Scheme for Brake and Valve Pedal Mechanisms

Siderail Toprail Ground Cable


p/n 988–2–676
Item AS
p/n 25–54
Pop Rivet
Bushing p/n 52–502
Item AT
p/n 13–17
Spindle Ext. Th. Lock Washer
Item AW

Side View of Pump Lever Arm and


Base Tube Gusset Grounding Scheme
Sidetube

30
2010–1–513 Basic Litter Assembly

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2020–1–518 Litter Frame Assembly 1 AA 946–1–108 I.V. Clip 2
B * Fowler Assembly 1 AB 23–64 Self–Tapping Screw 2
C (page 46) Gatch Assembly 1 AC 44–29 Dbl.–Sided Tape 12 Ft.
D ** Fowler Skin, Lexan 1 AD 11–13 Washer 2
E 958–1–525 Fowler Slide, Right 1 AE 17–6 Acorn Nut 2
F 958–1–526 Fowler Slide, Left 1 AF 25–69 Pop Rivet 4
H 988–31–623 Fowler Retention Pin 2 AH 37–10 Hole Plug 2
J 988–31–624 Fowler Pivot Liner 2 AJ 37–49 Hole Plug 6
K (page 48) Gatch Crankscrew Ass’y 1 AK 11–4 Washer 6
L 16–12 Fiberlock Nut 1 AL 4–28 Soc. Hd. Cap Screw 5
M 393–53–20 Strap Anchor 4 AM 4–86 Soc. Hd. Cap Screw 2
N 988–34–723 Support Plate 2 AN 4–137 Soc. Hd. Cap Screw 2
P 958–1–555 Fowler Stop 2 AP 4–142 Soc. Hd. Cap Screw 1
R 460–2–32 Grounding Cable 1 AR 15–13 Jam Nut 2
S 13–10 Ext. Tooth Lock Washer 2 AS 11–2 Washer 6
T 52–77 Spacer 2 AT 16–16 Fiberlock Nut 7
W 11–3 Washer 4 AW 4–86 Soc. Hd. Cap Screw 1
X 16–11 Nut 4 AX 2020–16–527 Hd./Ft. Board Pad 4
Y 28–50 Retaining Ring 2 AY 4–38 Soc. Hd. Cap Screw 1
Z 938–1–166 Modified Bolt 1 AZ 13–18 Ext. Tooth Lock Washer 1
BA 25–110 Pop Rivet 8

* When 2010–10, Standard Fowler Option, is ordered, use Fowler frame part number 988–2–587. When 2020–62, Head
Extension Fowler Option, is ordered, use Fowler frame part number 2020–62–12.
** When 2010–10, Standard Fowler Option, is ordered, use Fowler skin part number 988–31–635. When 2020–62, Head
Extension Fowler Option, is ordered, use Fowler skin part number 2020–62–28.

31
2010–1–515 Litter Assembly

Crosstube

LITTER GROUNDING
DETAIL

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A (page 31) Basic Litter Assembly 1 X 37–41 Hole Plug 2
B 2020–15–515 Frame End 1 Y 3–98 Hex Hd. Cap Screw 4
C 2020–15–512 Bumper 2 Z 3–97 Hex Hd. Cap Screw 4
D 52–45 Bushing 2 AA 1–71 Flat Hd. Mach. Screw 4
E 52–109 Washer 4 AB 4–109 Soc. Hd. Mach. Screw 4
F 2020–16–553 Crosstube Ass’y, Ft. 1 AC 16–40 Fiberlock Nut 8
H 2020–1–519 Crossbar, Head End 1 AD 926–33–36 Bearing 2
J 4–21 Soc. Hd. Cap Screw 4 AE 926–33–17 Spacer 2
K 958–1–576 Roller & Sleeve Ass’y 2 AF 958–31–618 Fowler Slide Lever 2
L 2020–1–521 Roller Shaft 2 AH 988–31–625 Fowler Arm Spacer 4
M 958–1–595 Sleeve, Hd. End 2 AJ 4–124 Soc. Hd. Cap Screw 2
N 16–61 Lock Nut 8 AK 2020–15–513 Litter Caulking 6 ft.
P 11–280 Washer 4 AL 2020–1–565 Litter Caulking 1 ft.
R 1–80 Flat Hd. Mach. Screw 8 AM 2010–1–212 Litter Ground/Wire 1
S 16–15 Fiberlock Nut 4 AN 13–18 Ext. Tooth Lock Washer 2
T 16–11 Fiberlock Nut 2 AP 23–25 Self–Tapping Screw 1
W 12–20 Lock Washer 6

32
2010–1–510 Litter Assembly with Standard Fowler

Item Part No. Part Name Qty.


A (page 32) Litter Assembly 1
B (page 34) Fowler Crankscrew Ass’y 1
C 938–1–166 Modified Bolt 1
D 15–13 Jam Nut 1

33
2010–31–610 Fowler Crankscrew Assembly

Item Part No. Part Name Qty.


A 958–1–545 Crank Disc 1
B 2020–1–531 Crank Handle 1
C 26–166 Groove Pin 1
D 26–14 Roll Pin 2
E 81–176 Thrust Washer 1
F 81–175 Thrust Bearing 1
H 81–174 Thrust Washer 2
J 938–1–175 Bearing Assembly 1
K 4–7 Soc. Hd. Cap Screw 1
M 2020–16–521 Knob 1
N 378–24–29 Shoulder Bolt 1
P 16–6 Kep Nut 1
R 958–75–21 Fowler Screw 1
S 2010–34–711 Screw Cover Assembly 1
T 958–31–617 Extension Tube Assembly 1
W 958–34–717 Magnet 1
Y 26–10 Roll Pin 2
Z 7900–1–102 Velcro Pile Tape 1

34
2010–75–510 & 2011–75–510 Emer. Drop Fowler Option Ass’y

2010–75–10 2011–75–10
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A (page 36) E. Drop C’screw Ass’y 1 A (page 36) E. Drop C’screw Ass’y 1
B 2010–75–517 Mounting Bracket 1 B 2010–75–517 Mounting Bracket 1
C 4–9 Soc. Hd. Cap Screw 2 C 4–9 Soc. Hd. Cap Screw 2
D 11–2 Washer 2 D 11–2 Washer 2
E 16–16 Fiberlock Nut 2 E 16–16 Fiberlock Nut 2
F 2010–75–520 Label 1 F 2010–75–520 Label 1
H 15–3 Hex Nut 1 H 15–3 Hex Nut 1
J 938–1–166 Modified Bolt 1 J 938–1–166 Modified Bolt 1
K 38–151 Cable Tie 1 K 38–151 Cable Tie 1
L 21–50 Set Screw 1 L 21–50 Set Screw 1
M 2010–75–519 Label 1 M 2011–1–120 Label 1
N 2020–1–554 Wire Guide 1 N 2020–1–554 Wire Guide 1
P 938–1–375 Actuating Cable 1 P 938–1–375 Actuating Cable 1

35
2010–75–515 Emergency Drop Fowler Crankscrew Ass’y

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 958–75–24 Cylinder Assembly 1 Z 958–1–545 Crank Disc 1
B 26–166 Groove Pin 1 AA 2020–1–531 Crank Handle 1
C 26–14 Roll Pin 2 AB 81–176 Thrust Washer 1
D 938–2–381 Release Assembly 1 AC 81–175 Thrust Bearing 1
E 938–2–341 Guide Tube Assembly 1 AD 81–174 Thrust Washer 2
F 938–1–359 ”U” Bolt 1 AE 938–1–175 Bearing Assembly 1
H 11–3 Washer 2 AF 4–7 Soc. Hd. Cap Screw 1
J 16–11 Flexlock Nut 2 AJ 2020–16–521 Knob 1
K 81–59 Nylon Bushing 1 AK 378–24–29 Shoulder Bolt 1
L 958–75–20 Extension Tube Assembly 1 AL 16–6 Kep Nut 1
M 26–10 Roll Pin 2 AM 958–75–21 Fowler Screw 1
N 11–104 Shim Washer As Req’d AN 958–34–717 Magnet 1
P 11–105 Shim Washer As Req’d AP 7900–1–102 Velcro Pile Tape 1
R 11–110 Shim Washer As Req’d AR 3–17 Hex Hd. Cap Screw 1
S 958–75–16 Brace Assembly 1 AS 11–63 Flat Washer 1
T 958–75–23 Crosstube Assembly 1 AT 16–16 Fiberlock Nut 1
W 938–1–367 Shoulder Bolt, Modified 1 AW 938–1–384 Cable Retainer 1
Y 2010–75–516 Screw Cover Assembly 1

36
2010–49–510 & 2011–49–510 Litter Ass’y, Basic Bed

2010–49–510 2011–49–510
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2020–15–515 Frame End 1 A 2020–15–515 Frame End 1
B 958–1–578 Supt. Tube Ass’y 4 B 958–1–578 Supt. Tube Ass’y 4
C 946–1–64 Label, Gatch 1 C 946–1–64 Label, Gatch 1
D 946–1–65 Label, Fowler 1 D 946–1–65 Label, Fowler 1
E 988–1–562 Label, I.V. Storage 1 E 2011–1–113 Label, I.V. Storage 1
H 11–280 Washer 8 F 52–502 Bushing 4
H 11–280 Washer 8

37
2010–50–510 & 2011–50–510 Litter Assembly, Position Option

HEAD END

Battery Power Ass’y


& Batteries
Fowler Pot. Cable Assembly To JP1 on
p/n 2020–2–652 Display Board
Trend. Pot. Cable Ass’y
To JP2 on Trend./Fowler p/n 2020–2–654
Display Board To JP3 on Trend./Fowler
Trend./Fowler Display Board Ass’y Display Board
p/n 2010–50–900

38
2010–50–510 & 2011–50–510 Litter Assembly, Position Option

2010–50–510 2011–50–510
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A (page 50) Frame End Ass’y 1 A (page 50) Frame End Ass’y 1
B 958–1–578 Support Tube Ass’y 4 B 958–1–578 Support Tube Ass’y 4
C 2010–50–520 Battery Holder Ass’y 1 C 2010–50–520 Battery Holder Ass’y 1
D 2010–50–519 Battery 3 D 2010–50–519 Battery 3
E 4–126 Hex Soc. Hd. Cap Scr. 2 E 4–126 Hex Soc. Hd. Cap Scr. 2
F 2020–31–622 Fowler Pot. Bracket 1 F 2020–31–622 Fowler Pot Bracket 1
H 2020–2–681 Pot. Cable Ass’y 1 H 2020–2–681 Pot. Cable Ass’y 1
J 4–42 Soc. Hd. Cap Screw 4 J 4–42 Soc. Hd. Cap Screw 4
K 988–2–231 Fowler Pot. Actuator 1 K 988–2–231 Fowler Pot. Actuator 1
L 27–13 Cotter Pin 2 L 27–13 Cotter Pin 2
M 26–34 Roll Pin 2 M 26–34 Roll Pin 2
N 988–2–244 Fowler Pivot Link 1 N 988–2–244 Fowler Pivot Link 1
P 988–2–243 Fowler Pivot Block 1 P 988–2–243 Fowler Pivot Block 1
R 8–21 Shoulder Bolt 1 R 8–21 Shoulder Bolt 1
S 2020–50–532 Clamp & Shaft Ass’y 1 S 2020–50–532 Clamp & Shaft Ass’y 1
T 52–705 Grommet 1 T 52–705 Grommet 1
W 23–55 Self–Tapping Screw 2 W 23–55 Self–Tapping Screw 2
X 2020–50–523 Pot. Housing 1 X 2020–50–523 Pot. Housing 1
Y 2020–1–428 Cover, Right 1 Y 2020–1–428 Cover, Right 1
Z 13–17 Washer 2 Z 13–17 Washer 2
AA 23–57 Self–Tapping Screw 2 AA 23–57 Self–Tapping Screw 2
AB 988–1–562 I.V. Storage Label 1 AB 2011–1–113 I.V. Storage Label 1
AC 2020–2–652 Fow. Pot. Cable Ass’y 1 AC 2020–2–652 Fow. Pot. Cable Ass’y 1
AD 2020–2–654 Trend. Pot. Cable Ass’y 1 AD 2020–2–654 Trend. Pot. Cable Ass’y 1
AE 30–17 Nylon Grommet Edging 16” AE 30–17 Nylon Grommet Edging 16”
AF 11–103 Washer 2 AF 11–103 Washer 2
AH 16–23 Fiberlock Nut 2 AH 16–23 Fiberlock Nut 2
AK 52–501 Push–In Rivet 6 AJ 52–502 Bushing 4
AL 52–500 Push Rivet 10 AK 52–501 Push–In Rivet 6
AM 37–39 Hole Plug 1 AL 52–500 Push Rivet 10
AN 11–280 Washer 4 AM 37–39 Hole Plug 1
AP 2020–2–651 F/T Pot. Cable Ass’y 1 AN 11–280 Washer 4
AP 2020–2–651 F/T Pot. Cable Ass’y 1

39
2010–52–510 & 2011–52–510 Litter Ass’y, All Options

p/n 958–59–511
Weigh System Cable
p/n 958–59–511 135 inch Cable
Weigh System Cable
73 inch Cable

HEAD END

p/n 958–59–511
Weigh System Cable
p/n 958–59–511 101 inch Cable
Weigh System Cable
39 inch Cable

40
2010–52–510 & 2011–52–510 Litter Ass’y, All Options

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A (page 51) Frame End Ass’y 1 A (page 51) Frame End Ass’y 1
B 2020–59–520 Load Cell Ass’y 4 B 2020–59–520 Load Cell Ass’y 4
C 2010–59–900 Scale CPU 1 C 2011–59–900 Scale CPU (TUV) 1
D 2020–59–411 Cover 4 D 2020–59–411 Cover 4
E 2020–1–554 Wire Guide 2 E 2020–1–554 Wire Guide 2
F 29–9 Dual Lock 6 F 29–9 Dual Lock 6
H 988–1–562 I.V. Storage Label 1 H 2011–1–113 I.V. Storage Label (TUV) 1
J 2010–1–106 Instruction Label, Top 1 J 2011–1–109 Instruction Label, Top 1
K 2020–1–572 Instruction Tab, Top 1 K 2020–1–572 Instruction Tab, Top 1
L 2010–1–107 Instruction Label, Middle 1 L 2011–1–107 Instruction Label, Middle 1
M 2020–1–573 Instruction Tab, Middle 1 M 2020–1–573 Instruction Tab, Middle 1
N 2010–1–108 Instruction Label, Bottom 1 N 2011–1–108 Instruction Label, Bottom 1
P 2020–1–574 Instruction Tab, Bottom 1 P 2020–1–574 Instruction Tab, Bottom 1
R 52–68 Cable Clamp 1 R 52–68 Cable Clamp 1
S 4–118 Soc. Hd. Screw 8 S 4–118 Soc. Hd. Screw 8
T 2010–59–528 Battery Assembly 3 T 2010–59–528 Battery Assembly 3
W 29–7 Dual Lock 6 W 29–7 Dual Lock 6
X 4–12 Soc. Hd. Cap Screw 1 X 4–12 Soc. Hd. Cap Screw 1
Y 14–20 Washer 4 Y 14–20 Washer 4
Z 4–101 Soc. Hd. Cap Screw 6 Z 4–101 Soc. Hd. Cap Screw 6
AA 52–91 Spacer 6 AA 52–91 Spacer 6
AB 52–89 Nylon Screw 6 AB 52–89 Nylon Screw 6
AC 15–27 Jam Nut 2 AC 15–27 Jam Nut 2
AD 2020–2–654 Trend. Pot. Cable Ass’y 1 AD 2020–2–654 Trend. Pot. Cable Ass’y 1
AE 2010–59–520 Power System Cord 1 AE 2010–59–520 Power System Cord 1
AF 2010–59–527 Frame Tube Cover 1 AF 2010–59–527 Frame Tube Cover 1
AH 52–94 Cable Clamp 2 AH 52–94 Cable Clamp 2
AJ 13–18 Ext. Tooth Lock Washer 3 AJ 13–18 Ext. Tooth Lock Washer 3
AK 38–111 Cable Tie 4 AK 38–111 Cable Tie 4
AL 30–17 Nylon Grommet Edging 32” AL 30–17 Nylon Grommet Edging 32”
AM 16–3 Fiberlock Nut 3 AM 16–3 Fiberlock Nut 3
AN 958–59–511 Weigh System Cable 1 AN 958–59–511 Weigh System Cable 1
AP 59–42 Key 16 AP 59–42 Key 16
AR 15–4 Jam Nut 1 AR 15–4 Jam Nut 1
AS 4–8 Soc. Hd. Screw 3 AS 4–8 Soc. Hd. Screw 3
AT 2010–1–114 Label, Battery 1 AT 2010–1–114 Label, Battery 1
AW 2020–1–428 Cover, Right 1 AW 2020–1–428 Cover, Right 1
AX 2020–31–622 Fowler Pot. Bracket 1 AX 2020–31–622 Fowler Pot. Bracket 1
AY 2020–2–681 F/T Cable Ass’y 1 AY 2020–2–681 F/T Cable Ass’y 1
AZ 988–2–244 Fowler Pivot Link 1 AZ 988–2–244 Fowler Pivot Link 1
BA 988–2–243 Fowler Pivot Block 1 BA 988–2–243 Fowler Pivot Block 1
BB 988–2–231 Fowler Pot. Actuator 1 BB 988–2–231 Fowler Pot. Actuator 1
BC 4–42 Soc. Hd. Screw 4 BC 4–42 Soc. Hd. Screw 4
BD 8–21 Shoulder Bolt 1 BD 8–21 Shoulder Bolt 1
BE 23–25 Self–Tapping Screw 2 BE 23–25 Self–Tapping Screw 2
BF 27–13 Cotter Pin 2 BF 27–13 Cotter Pin 2
BH 26–34 Roll Pin 2 BH 26–34 Roll Pin 2
BJ 2010–50–523 Pot. Housing 1 BJ 2010–50–523 Pot. Housing 1
BK 2020–50–532 Clamp & Shaft Ass’y 1 BK 2020–50–532 Clamp & Shaft Ass’y 1
BL 23–55 Self–Tapping Screw 2 BL 23–55 Self–Tapping Screw 2
BM 52–705 Grommet 1 BM 52–705 Grommet 1
BN 2020–2–637 Scale Cable Ass’y 1 BN 2020–2–637 Scale Cable Ass’y 1
BP 2010–59–525 Trend/Fow. Power Cable 1 BP 2010–59–525 Trend/Fow. Power Cable 1
BR 2010–59–521 Switch LED Syst. Cable 1 BR 2010–59–521 Switch LED Syst. Cable 1
BS 23–57 Self–Tapping Screw 2 BS 23–57 Self–Tapping Screw 2
BT 13–17 Ext. Tooth Lock Washer 2 BT 13–17 Ext. Tooth Lock Washer 2
BW 2010–1–109 Battery Storage Label 1 BW 2011–1–118 Battery Storage Label 1
BX 2020–2–652 Fowler Pot. Cable Ass’y 1 BX 2020–2–652 Fowler Pot. Cable Ass’y 1
BY 2010–1–112 Label, Fuse Warning 1 BY 2010–1–112 Label, Fuse Warning 1
BZ 52–501 Push–In Rivet 6 BZ 52–501 Push–In Rivet 6
CA 52–500 Push Rivet 4 CA 52–500 Push Rivet 4
CB 37–39 Hole Plug 1 CB 37–39 Hole Plug 1
CD 2020–59–518 Spacer 8 CC 52–502 Bushing 4
CE 2020–2–651 F/T Pot. Cable 1 CD 2020–59–518 Spacer 8
CE 2020–2–651 F/T Pot. Cable 1

41
2010–52–510 & 2011–52–510 Litter Ass’y, All Options

Fowler/Trend.
Power Cable Switch/LED
p/n 2010–59–525 System Cable Trend. Sensor Cable Ass’y
p/n 2010–59–521 p/n 2020–2–654
Power System Cable To JP6 on Scale CPU To JP3 on Trend./
p/n 2010–59–520 To JP1 on Fowler Display Board
To JP8 on Scale CPU Trend./Fowler
Display Board

Ground Wire
p/n 2020–2–629
To P1 on Scale CPU

Weigh System Cable


Drain Wire p/n 958–59–511
To JP3 on Scale CPU
Fowler Sensor Cable Ass’y
p/n 2020–2–652 Scale Cable Assembly
To JP2 on Trend./Fowler p/n 2020–2–637
Display Board

Switch Board LCD/Display Keypad Circuit Board


Trend./ Fowler Display p/n 2010–59–516 p/n 2020–59–512
Board Assembly
p/n 2010–50–900

Load Cell

Load Cell Cable

Side Tube

Weigh Board to Weigh Cable Connections

42
2010–59–510 & 2011–59–510 Litter Ass’y, Scale Option

Switch/LED
System Cable
p/n 2010–59–521
To JP6 on Scale CPU

Power System Cable


p/n 2010–59–520
To JP8 on Scale CPU
Ground Wire
p/n 2020–2–629
To P1 on on Scale CPU

Weigh System Cable


p/n 958–59–511
Drain Wire To JP3 on Scale CPU

Scale Cable Assembly


p/n 2020–2–637

Switch Board LCD/Display Keypad Circuit Board


p/n 2010–59–910 p/n 2020–59–512

Load Cell

Load Cell Cable

Side Tube

WEIGH BOARD TO WEIGH CABLE CONNECTIONS

43
2010–59–510 & 2011–59–510 Litter Ass’y, Scale Option

958–59–511
958–59–511 Weigh System Cable
Weigh System Cable 135 inch Cable
73 inch Cable

958–59–511
Weigh System Cable
958–59–511 101 inch Cable
Weigh System Cable
39 inch Cable

44
2010–59–510 & 2011–59–510 Litter Ass’y, Scale Option

2010–59–510 2011–59–510
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A (page 49) Frame End Ass’y 1 A (page 49) Frame End Ass’y 1
B 2020–59–520 Load Cell Assembly 4 B 2020–59–520 Load Cell Assembly 4
C 2010–59–900 Scale CPU 1 C 2011–59–900 Scale CPU (TUV) 1
D 2020–59–411 Cover 4 D 2020–59–411 Cover 4
E 2020–1–554 Wire Guide 2 E 2020–1–554 Wire Guide 2
F 29–9 Dual Lock 6 F 29–9 Dual Lock 6
H 988–1–562 I.V. Storage Label 1 H 2011–1–113 I.V. Storage Label (TUV) 1
J 2010–1–106 Instruction Label, Top 1 J 2011–1–109 Instruction Label, Top 1
K 2020–1–572 Instruction Tab, Top 1 K 2020–1–572 Instruction Tab, Top 1
L 2010–1–107 Instruction Label, Middle 1 L 2011–1–107 Instruction Label, Middle 1
M 2020–1–573 Instruction Tab, Middle 1 M 2020–1–573 Instruction Tab, Middle 1
N 2010–1–108 Instruction Label, Bottom 1 N 2011–1–108 Instruction Label, Middle 1
P 2020–1–574 Instruction Tab, Bottom 1 P 2020–1–574 Instruction Tab, Bottom 1
R 52–68 Cable Clamp 1 R 52–68 Cable Clamp 1
S 4–118 Soc. Hd. Screw 8 S 4–118 Soc. Hd. Screw 8
T 2010–59–528 Battery Assembly 3 T 2010–59–528 Battery Assembly 3
W 29–7 Dual Lock 6 W 29–7 Dual Lock 6
X 4–12 Soc. Hd. Cap Screw 1 X 4–12 Soc. Hd. Cap Screw 1
Y 14–20 Washer 4 Y 14–20 Washer 4
Z 4–101 Soc. Hd. Cap Screw 6 Z 4–101 Soc. Hd. Cap Screw 6
AA 52–91 Spacer 6 AA 52–91 Spacer 6
AB 52–89 Nylon Screw 6 AB 52–89 Nylon Screw 6
AC 15–27 Jam Nut 2 AC 15–27 Jam Nut 2
AD 2010–1–109 Battery Storage Label 1 AD 2011–1–118 Battery Storage Label 1
AE 2010–59–520 Power System Cord 1 AE 2010–59–520 Power System Cord 1
AF 2010–59–527 Frame Tube Cover 1 AF 2010–59–527 Frame Tube Cover 1
AH 52–94 Cable Clamp 1 AH 52–94 Cable Clamp 1
AJ 13–18 Ext. Tooth Lock Washer 3 AJ 13–18 Ext. Tooth Lock Washer 3
AK 38–111 Cable Tie 4 AK 38–111 Cable Tie 4
AL 30–17 Nylon Grommet Edging 32” AL 30–17 Nylon Grommet Edging 32”
AM 16–3 Fiberlock Nut 2 AM 16–3 Fiberlock Nut 2
AN 958–59–511 Weigh System Cable 1 AN 958–59–511 Weigh System Cable 1
AP 59–42 Key 16 AP 59–42 Key 16
AR 15–4 Jam Nut 1 AR 15–4 Jam Nut 1
AS 4–8 Soc. Hd. Screw 2 AS 4–8 Soc. Hd. Screw 2
AT 2010–1–114 Label, Battery 1 AT 2010–1–114 Label, Battery 1
AW 2020–2–637 Scale Cable Ass’y 1 AW 2020–2–637 Scale Cable Ass’y 1
AX 2010–59–521 Switch LED Cable Ass’y 1 AX 2010–59–521 Switch LED Cable Ass’y 1
AY 2010–1–112 Label, Fuse Warning 1 AY 2010–1–112 Label, Fuse Warning 1
AZ 52–501 Push–In Rivet 6 AZ 52–501 Push–In Rivet 6
BA 52–500 Push Rivet 4 BA 52–500 Push Rivet 4
BB 37–39 Hole Plug 1 BB 37–39 Hole Plug 1
BD 2020–59–518 Spacer 8 BC 52–502 Bushing 4
BD 2020–59–518 Spacer 8

45
2020–34–750 Knee Gatch Assembly

Item Part No. Part Name Qty.


A 2020–34–753 Thigh Section Assembly 1
B (page 47) Calf Section Assembly 1
C 2020–1–701 Strap Anchor 2
D 4–51 Soc. Hd. Cap Screw 2
E 460–4–32 Grounding Cable 1
F 14–3 Flat Washer 6
H 16–11 Fiberlock Nut 2
J 13–10 Ext. Tooth Lock Washer 3
K 988–2–676 Grounding Cable 1
L 23–25 Self Tapping Mach. Screw 3
N 25–79 Pop Rivet 4

46
2020–34–760 Calf Section Assembly

Item Part No. Part Name Qty.


A 2020–34–755 Calf Section Assembly 1
B 2020–34–758 Calf Section Rest 2
C 16–3 Fiberlock Nut 2
D 25–71 Pop Rivet 2
E 2020–34–762 Gatch Stand Assembly 1
F 16–16 Fiberlock Nut 2
H 14–2 Nylon Washer 4
J 3–3 Hex Hd. Cap Screw 2
K 2–36 Rd. Hd. Machine Screw 2
L 11–1 Flat Washer 2
M 938–1–69 Knee Gatch Handle 1
N 29–7 Dual Lock 1
P 29–9 Dual Lock 1
R 11–2 Flat Washer 2

47
2010–34–710 Knee Gatch Crankscrew Assembly

Item Part No. Part Name Qty.


A 958–1–545 Crank Disc 1
B 2020–1–531 Crank Handle 1
C 26–166 Groove Pin 1
D 26–14 Roll Pin 2
E 81–176 Thrust Washer 1
F 81–175 Thrust Bearing 1
H 81–174 Thrust Washer 2
J 938–1–175 Bearing Assembly 1
K 4–7 Soc. Hd. Cap Screw 1
M 2020–16–521 Knob 1
N 378–24–29 Shoulder Bolt 1
P 16–6 Kep Nut 1
R 958–34–731 Knee Gatch Screw 1
S 2010–34–711 Screw Cover Assembly 1
T 2010–34–713 Extension Tube 1
W 958–34–717 Magnet 1
Y 26–10 Roll Pin 2
Z 7900–1–102 Velcro Adhesive Pile 2

48
2010–59–519 & 2011–59–519 Frame End Ass’y, Scale Option

2010–59–519 2011–59–519
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2010–59–517 Frame End, Scale Opt. 1 A 2010–59–517 Frame End, Scale Opt. 1
B 2020–57–512 Scale Disp./Keyboard 1 B 2020–57–512 Scale Disp./Keyboard 1
C 1–70 Flat Hd. Mach. Screw 10 C 1–70 Flat Hd. Mach. Screw 10
D 16–51 Nut 10 D 16–51 Nut 10
E 52–90 Spacer 10 E 52–90 Spacer 10
F 2010–59–526 Ft. End Control Label 1 F 2011–59–526 Ft. End Control Label 1
H 2020–1–566 Clear Shield 1 H 2020–1–566 Clear Shield 1
J 2010–1–115 Label O2 Hazard 1 J 2011–1–114 Label O2 Hazard 1
K 2020–1–146 Label, Scale 1 K 2011–1–115 Label, Scale 1
L 2010–1–105 Label, On/Off 1 L 2011–1–116 Label, On/Off 1
M 2010–59–910 Switch Board 1 M 2010–59–910 Switch Board 1

49
2010–50–515 & 2011–50–515 Frame End Ass’y, Position Option

2010–50–515 2011–50–515
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2010–50–518 Frame End, Basic 1 A 2010–50–518 Frame End, Basic 1
B 2010–50–900 Trend/Fow. Disp. Bd. 1 B 2010–50–900 Trend/Fow. Disp. Bd. 1
C 1–70 Flat Hd. Mach. Screw 4 C 1–70 Flat Hd. Mach. Screw 4
D 16–51 Nut 4 D 16–51 Nut 4
E 52–90 Spacer 4 E 52–90 Spacer 4
F 2010–50–517 Ft. End Control Label 1 F 2011–50–517 Ft. End Control Label 1
H 2020–1–566 Clear Shield 1 H 2020–1–566 Clear Shield 1
J 2010–1–115 Label, O2 Hazard 1 J 2011–1–114 Label, O2 Hazard 1

50
2010–52–515 & 2011–52–515 Frame End Ass’y, All Options

2010–52–515 2011–52–515
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2010–52–516 Frame End, All Options 1 A 2010–52–516 Frame End, All Options 1
B 2020–57–512 Scale Disp./Keyboard 1 B 2020–57–512 Scale Disp./Keyboard 1
C 1–70 Flat Hd. Mach. Screw 14 C 1–70 Flat Hd. Mach. Screw 14
D 16–51 Nut 14 D 16–51 Nut 14
E 52–90 Spacer 14 E 52–90 Spacer 14
F 2010–52–517 Foot End Ctrl. Label 1 F 2011–52–517 Foot End Ctrl. Label 1
H 2020–1–566 Clear Shield 1 H 2020–1–566 Clear Shield 1
J 2010–1–115 Label, O2 Hazard 1 J 2011–1–114 Label, O2 Hazard 1
K 2020–1–146 Label, Scale 1 K 2011–1–115 Label, Scale 1
L 2010–1–105 Label, On/Off 1 L 2011–1–116 Label, On/Off 1
M 2010–50–900 Trend/Fow. Disp. Bd. 1 M 2010–50–900 Trend/Fow. Disp. Bd. 1
N 2010–59–910 Switch Board 1 N 2010–59–910 Switch Board 1

51
2020–26–815 & 2011–26–815 Siderail Ass’y, Fold Head

HEAD
END

Item Part No. Part Name Qty.


A 938–1–188 Top Rail 1
B 37–42 Round Hole Plug 5
C 25–61 Semi–Tubular Rivet 6
D 958–26–17 Upright 5
E 2020–28–815 Lock Spindle 1
F 2020–90–865 Pivot 6
2020–90–840 Pivot (2011)
H 946–26–29 Siderail Latch Assembly 1
J 1–22 Flat Hd. Mach. Screw 2
4–49 Hex Soc. Hd. Cap Screw (2011) 2
K 2020–26–816 Spacer 6
L 2020–26–817 Pivot Bar 1

52
2020–26–810 & 2011–26–810 Siderail & Bumper Ass’y, Lt., Fold Head

Left Sidetube

HEAD END

Item Part No. Part Name Qty.


A (page 52) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flexlock Nut 7
D 11–3 Washer 7
E 3–88 Hex Hd. Cap Screw 7
F 3–2 Hex Hd. Cap Screw 2
H 958–26–821 Bumper, Left 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 958–1–529 Midsection Skin (not shown) 1

53
2020–26–811 & 2011–26–811 Siderail & Bumper Ass’y, Rt., Fold Head

HEAD END

Item Part No. Part Name Qty.


A (page 52) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flexlock Nut 7
D 11–3 Washer 7
E 3–88 Hex Hd. Cap Screw 7
F 3–2 Hex Hd. Cap Screw 2
H 958–26–820 Bumper, Right 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 958–1–529 Midsection Skin (not shown) 1

54
2020–27–812 & 813 Siderail Ass’y, Lt. & Rt., Fold Foot
2011–27–815 Siderail Assembly, Fold Foot

FOOT END

Item Part No. Part Name Qty.


A 938–1–188 Top Rail 1
B 37–42 Round Hole Plug 5
C 25–61 Semi–Tubular Rivet 6
D 958–26–17 Upright 5
E 2020–28–815 Lock Spindle 1
F 2020–90–865 Pivot 6
2020–90–840 Pivot (2011) 6
H 946–26–29 Siderail Latch Assembly 1
J 1–22 Flat Hd. Mach. Screw 2
4–49 Hex Soc. Hd. Cap Screw (2011) 2
K 2020–26–817 Pivot Sleeve 1
L 2020–26–816 Spacer 6

55
2020–27–811 & 2011–27–811 SIderail & Bumper Ass’y, Rt., Fold Foot

FOOT END

Right Sidetube

Item Part No. Part Name Qty.


A (page 55) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flexlock Nut 7
D 11–3 Washer 7
E 3–88 Hex Hd. Cap Screw 7
F 3–2 Hex Hd. Cap Screw 2
H 958–26–820 Bumper, Right 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 11–2 Flat Washer 2
M 958–1–529 Midsection Skin (not shown) 1

56
2020–27–810 & 2011–27–810 Siderail & Bumper Ass’y, Lt., Fold Foot

FOOT END

Item Part No. Part Name Qty.


A (page 55) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flex Lock Nut 7
D 11–3 Washer 7
E 3–88 Hex Hd. Cap Screw 7
F 3–2 Hex Hd. Cap Screw 2
H 958–26–821 Bumper, Left 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 11–2 Flat Washer 2
M 958–1–529 Midsection Skin (not shown) 1

57
2020–28–812 & 2011–28–815 Split Folddown Siderail Ass’y

Item Part No. Part Name Qty.


A 2020–28–816 Top Rail, Front 1
B 2020–28–825 Top Rail, Rear 1
C 2020–28–815 Lock Spindle 2
D 958–26–17 Upright 3
E 2020–28–818 Front Spindle 1
F 946–26–29 Siderail Lock Assembly 2
H 2020–90–865 Pivot (2020) 6
2020–90–840 Pivot (2011) 6
K 2020–26–817 Pivot Bar 2
L 1–22 Flat Hd. Mach. Screw 4
M 37–43 Siderail Endplug 4
N 25–61 Semi–Tubular Rivet 6
P 2020–26–816 Spacer 6
R 37–42 Plug 4

58
2020–28–810 Siderail & Bumper Assembly, Split, Left

Item Part No. Part Name Qty.


A (page 58) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flexlock Nut 8
D 11–3 Washer 8
E 3–88 Hex Hd. Cap Screw 8
F 3–1 Hex Hd. Cap Screw 2
H 958–26–821 Bumper, Left 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 2020–1–599 Midsection Skin (not shown) 1

59
2020–28–811 Siderail & Bumper Assembly, Split, Right

Item Part No. Part Name Qty.


A (page 58) Siderail Assembly 1
B 14–19 Washer 12
C 16–11 Flexlock Nut 8
D 11–3 Washer 8
E 3–88 Hex Hd. Cap Screw 8
F 3–1 Hex Hd. Cap Screw 2
H 958–26–820 Bumper, Right 1
J 988–1–576 Cap 1
K 16–16 Fiberlock Nut 2
L 2020–1–599 Midsection Skin (not shown) 1

60
958–224–10 Folding I.V. Holder Assembly

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 946–224–1 Hanger 2 M 958–224–11 Label 1
B 14–16 Washer 2 N 958–224–21 Adhesive Pad 1
C 26–147 Groove Pin 1 P 21–107 Set Screw 1
D 946–224–2 Top Bracket, Mach’d 1 R 2020–19–518 I.V. Sleeve, Mach’d 1
E 2020–1–162 Label 2 S 13–33 Lock Washer 2
F 946–224–33 Grip Assembly 1 T 4–112 Soc. Hd. Cap Screw 2
H 946–224–4 Lock 1 W 958–224–20 Hinge Pin 1
J 946–224–5 Ring 1 Y 25–37 Pop Rivet 1
K 946–224–3 Inner Tube 1 Z 958–224–18 Rest 1
L 2020–19–512 Hinge & Outer Tube Ass’y 1

61
2011–24–510 Folding I.V. Holder Assembly

Item Part No. Part Name Qty.


A 946–224–1 Hanger 2
B 14–16 Washer 2
C 26–147 Groove Pin 1
D 946–224–2 Top Bracket, Mach’d 1
E 2011–24–511 Label 2
F 946–224–33 Grip Assembly 1
H 946–224–4 Lock 1
J 946–224–5 Ring 1
K 946–224–3 Inner Tube 1
L 2020–19–512 Hinge & Outer Tube Ass’y 1
M 1010–95–24 Label 1
N 4–179 Soc. Hd. Cap Screw 1
P 2011–24–512 Label 1
R 2020–19–518 I.V. Sleeve, Mach’d 1
S 13–33 Lock Washer 2
T 4–112 Soc. Hd. Cap Screw 1
W 958–224–20 Hinge Pin 1
Y 25–37 Pop Rivet 1
Z 958–224–18 Rest 1
AA 958–224–21 Adhesive Pad 1
AB 21–107 Set Screw 1

62
2020–77–512 Isolated I.V. Socket Ass’y, Std. I.V. Pole

Item Part No. Part Name Qty.


A 2020–77–511 Isolated I.V. Assembly 1
B 2020–77–524 Label 1
C 2020–77–520 Socket Insert Ass’y 2
D 721–32–49 Bumper Roller 2
E 21–131 Set Screw 2
F 8–35 Shoulder Bolt 2
H 11–14 Washer 2

62.1
2020–78–512 Isolated I.V. Socket Ass’y, Std. or Perm. I.V. Pole

Item Part No. Part Name Qty.


A 2020–77–511 Isolated I.V. Assembly 1
B 2020–77–524 Label 1
C 2020–77–520 Socket Insert Ass’y 1
D 721–32–49 Bumper Roller 2
E 21–131 Set Screw 1
F 8–35 Shoulder Bolt 2
H (page 62.3) I.V. Pole Assembly 1
J 1015–24–35 Retaining Pin 1
K 11–14 Washer 2

62.2
2020–78–525 Permanent, Isolated I.V. Pole Assembly

Item Part No. Part Name Qty.


A 1510–59–15 Base Tube Assembly 1
B 926–400–31 Extension Tube Assembly 1
C 1210–110–46 Back–Up Ring 1
D 1210–110–47 Lock Ring 1
E 1210–110–49 Lock Actuator 1
H 14–20 Nylon Flat Washer 1
J 1010–59–16 I.V. Hook 2
K 52–17 Nylon Spacer 2
L 8–31 Shoulder Bolt 1
M 2020–78–516 I.V. Tube Spacer 1
N 926–400–62 Stop Sleeve 1
R 2020–78–517 Logo Label 1

62.3
Notes

62.4
2020–30–210 & 2020–30–220 O2 Bottle Holder Assembly

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2020–30–215 Bottle Holder Assembly 2 D 38–221 Compression Spring 2
B 2020–30–211 Pivot Support 1 E 2020–30–217 O2 Bottle Label, Left 1
C 26–10 Roll Pin 2 F 2020–30–218 O2 Bottle Label, Right 1

Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 2020–30–220 O2 Mounted Assembly 1 F 16–16 Nylock Hex Nut 2
C 2020–30–221 Adhesive Mat 1 J 13–10 Washer 2
E 3–79 Hex Hd. Cap Screw 2

63
2011–30–511 & 2011–30–510 O2 Bottle Holder Assembly

Item Part No. Part Name Qty.


A 2020–30–215 Bottle Holder Assembly 2
B 2020–30–211 Pivot Support 1
C 26–10 Roll Pin 2
D 38–221 Compression Spring 2
E 2011–1–117 Label, Left 1
F 2011–1–119 Label, Right 1

Item Part No. Part Name Qty.


A 2011–30–511 O2 Mounted Assembly 1
C 2020–30–221 Adhesive Mat 1
E 3–79 Hex Hd. Cap Screw 2
F 16–16 Nylock Hex Nut 2
J 11–53 Washer 2

64
2020–39–510 Defibrillator Tray Assembly

Item Part No. Part Name Qty.


A 2020–39–535 Defibrillator Tray 1
B 2020–39–521 Leg Assembly, Left 1
C 2020–39–520 Leg Assembly, Right 1
D 2020–39–513 Label 1
F 26–14 Roll Pin 2
H 946–1–283 Weight Label 1
J 390–57–12 Long Strap 1
K 1010–50–21 Short Strap 1
L 350–2–24 Collar 2
M 2020–39–530 Support Tube Assembly 1
N 29–8 Dual Lock 12
P 29–10 Dual Lock 12
R 938–1–401 Collar 2

65
2020–55–10 Fowler X–Ray Cassette Assembly

Item Part No. Part Name Qty.


A 938–20–13 Cassette Holder 1
B 1–58 Flat Hd. Machine Screw 4
C 938–20–20 Channel Top Assembly 1
D 11–63 Washer 4
E 16–16 Fiberlock Nut 4
F 938–20–22 Channel Bottom 1
H 24–34 Plastic Knob 1
J 2020–55–18 Siderail Tube 2
K 2020–55–15 Support Angle Weldment 2
L 21–64 Set Screw 5
M 2–31 Round Hd. Screw 4
N 16–14 Self–Locking Nut 4
P 2–10 Round Hd. Machine Screw 12
R 2020–55–19 Bearing Housing 1
S 926–23–62 Post Housing 6
T 2020–55–20 Actuating Rod 2
W 38–122 Compression Spring 2
Y 15–2 Hex Nut 12
Z 926–23–64 Post 4
AA 926–23–63 Actuating Rod 2
AB 926–23–65 Bearing Housing 1
AC 2020–58–28 Stop Collar 1

66
2020–54–11 Fowler X–Ray Cassette Retro–Fit Assembly

Item Part No. Part Name Qty.


A 23–55 Self–Tapping Sheet Metal Screw 4
B 2020–55–21 Fowler Tab Assembly 2
C 2020–55–24 Pivot Assembly, Right 1
D 4–6 Soc. Hd. Cap Screw 2
E 2020–55–25 Pivot Assembly, Left 1
F 2020–54–101 X–Ray Cass. Drill Jig (not shown) 1

67
Warranty

Limited Warranty:
Stryker Medical Division, a division of Stryker Corporation, warrants to the original purchaser that its products
should be free from defects in material and workmanship for a period of one (1) year after date of delivery.
Stryker’s obligation under this warranty is expressly limited to supplying replacement parts and labor for, or
replacing, at its option, any product which is, in the sole discretion of Stryker, found to be defective. Stryker
warrants to the original purchaser that the frame and welds on its beds will be free from structural defects
for as long as the original purchaser owns the bed. If requested by Stryker, products or parts for which a
warranty claim is made shall be returned prepaid to Stryker’s factory. Any improper use or any alteration or
repair by others in such manner as in Stryker’s judgement affects the product materially and adversely shall
void this warranty. No employee or representative of Stryker is authorized to change this warranty in any way.
This statement constitutes Stryker’s entire warranty with respect to the aforesaid equipment. STRYKER
MAKES NO OTHER WARRANTY OR REPRESENTATION, EITHER EXPRESSED OR IMPLIED, EXCEPT
AS SET FORTH HEREIN. THERE IS NO WARRANTY OF MERCHANTABILITY AND THERE ARE NO
WARRANTIES OF FITNESS FOR ANY PARTICULAR PURPOSE. IN NO EVENT SHALL STRYKER BE
LIABLE HEREUNDER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OR IN ANY
MANNER RELATED TO SALES OR USE OF ANY SUCH EQUIPMENT.

To Obtain Parts and Service:

Stryker products are supported by a nationwide network of dedicated Stryker Field Service Representatives.
These representatives are factory trained, available locally, and carry a substantial spare parts inventory to
minimize repair time. Simply call your local representative, or call Stryker Customer Service at (800)
327–0770.

Supplemental Warranty Coverage:


Stryker has developed a comprehensive program of extended warranty options designed to keep your equip-
ment operating at peak performance at the same time it eliminates unexpected costs. We recommend that
these programs be activated before the expiration of the new product warranty to eliminate the potential of
additional equipment upgrade charges. Stryker offers the following Supplemental Warranties:

Extended (Parts and Labor)


S All replacement parts (excluding mattresses and consumable items)
S Labor and travel for all scheduled and unscheduled calls
S Biannual Preventive Maintenance Inspections and repairs
S JCAHO paperwork for preventive maintenance
S Priority Emergency Service

Standard (Labor Only):


S Labor and travel for all scheduled and unscheduled calls
S Biannual Preventive Maintenance Inspections and repairs
S JCAHO paperwork for preventive maintenance
S Priority Emergency Service

Basic (Parts Only):


S All replacement parts (excluding mattresses and consumable items)
S Priority Emergency Service

Please call your local representative, or call (800) 327–0770 for further information

68
Warranty

Return Authorization:
Merchandise cannot be returned without approval from the Stryker Customer Service Department. An autho-
rization number will be provided which must be printed on the returned merchandise. Stryker reserves the
right to charge shipping and restocking fees on returned items.
SPECIAL, MODIFIED, OR DISCONTINUED ITEMS NOT SUBJECT TO RETURN.
Damaged Merchandise:
ICC Regulations require that claims for damaged merchandise must be made with the carrier within fifteen
(15) days of receipt of merchandise. DO NOT ACCEPT DAMAGED SHIPMENTS UNLESS SUCH DAMAGE
IS NOTED ON THE DELIVERY RECEIPT AT THE TIME OF RECEIPT. Upon prompt notification, Stryker
will file a freight claim with the appropriate carrier for damages incurred. Claim will be limited in amount to
the actual replacement cost. In the event that this information is not received by Stryker within the fifteen
(15) day period following the delivery of the merchandise, or the damage was not noted on the delivery receipt
at the time of receipt, the customer will be responsible for payment of the original invoice in full.
Claims for any short shipment must be made within thirty (30) days of invoice.
International Warranty Clause:
This warranty reflects U.S. domestic policy. Warranty outside the U.S. may vary by country. Please contact
your local Stryker Medical representative for additional information.

69
6300 Sprinkle Road, Kalamazoo, MI 49001–9799 (800) 327–0770

DH 10/92 2010–1–111 REV __

You might also like