PIM-530 Series Protectowire Linear Heat Detector

Interface Module

F eatures
• Provides a single zone interface for Protectowire Digital
Linear Heat Detectors
• Capable of Class A (Style D) or Class B (Style B)
monitoring of up to 6560 Feet (2000 Meters) of
Protectowire Linear Heat Detector
• Integrated Protectowire Alarm Point Location Meter with
“on-screen” field calibration
• 64 Event History Log (FIFO)
• 4x20 LED backlit LCD display
• Individual Power, Alarm and Fault indicators
• Modbus over RS-485 communications
• 4-20mA outputs for Status and Alarm Point Location
• Optional intrinsically safe detection circuit available for
use in hazardous locations

General
The PIM-530 is a detection control module that acts as an inter- In order to ensure proper operation, each PIM-530 module re-
face between a main fire alarm control panel detection circuit or quires regulated resettable 24 VDC external power which is nor-
addressable node and Protectowire Digital Linear Heat Detector. mally provided by the host fire alarm panel. Each module
The module provides one (1) supervised detection circuit that contains a green “Power-On” LED indicator, one (1) red “Alarm”
may be field wired for either Class A (Style D) or Class B (Style B) LED indicator, and one (1) yellow “Trouble” LED indicator. One
service. The alarm initiating circuit is capable of operating up to (1) set of Form C alarm contacts and one (1) set of Form C trou-
6560 feet (2000 meters) of Standard PHSC or PLR Digital Type ble contacts to connect the unit to the host fire alarm panel. The
Protectowire Linear Heat Detectors. The PIM-530 initiating cir- module also provides Modbus over RS-485 communications and
cuit is also compatible with other types of non-resistive normally two 4-20mA outputs one which allows monitoring of the module
open contact alarm initiating devices. status and the other for monitoring alarm point location informa-
tion.
Description
The standard PIM-530 module contains a built in Protectowire
The PIM-530 operates using conventional initiating device circuit
Alarm Point Location Meter. This meter will automatically display
technology and contains an integrated on-board Protectowire
the distance from the beginning of the detector run to the heat ac-
Alarm Point Location Meter. The module also includes a time and
tuated (shorted) portion of the detector. The Alarm Point Location
date clock, 64 event history log, Form C contacts for host panel
Meter can be programmed to display distance in either standard
interface and dual 4-20mA status outputs.
units (Feet) or metric units (Meters). The meter display provides a
The module is designed for easy installation and can be optionally simple “on screen” calibration procedure allowing the measure-
provided in a NEMA-4X* rated enclosure for mounting outside ment to be field calibrated to the installed detector length and am-
of the host fire alarm control panel or remotely near the hazard to bient temperature for optimal accuracy.
be protected.

APPROVED An ISO 9001 Registered Company

 4-20mA Outputs
Specifications • One(1) 4-20mA Output for module status
Electrical • One (1) 4-20mA Output for Alarm Point Location Readings
• Power input - Regulated 12 to 24 VDC (+10% / -15%) @ Optional Enclosure Specifications
1.6 Watt • 10.5" H x 8.5" W x 4.5" D (27cm x 21.5cm x 11.4cm)
• Power Limited, onboard surge and EMI protection devices • Add 1.6" (4cm) to overall height for external mounting feet
Inputs • Clear full view door
• One initiating device circuit capable of monitoring up to • NEMA 4X Rated (Rating UL listed only)*
6,560 feet (2,000 m) of PHSC or PLR Digital Type (Closest IEC equivalent - IP66)
Protectowire Linear Heat Detector. Option I increases enclosure size. Consult Factory.
Option I Option I - Intrinsically Safe Detection Circuit
• Intrinsically Safe Initiating device circuit, up to 6,560 feet • Option I provides an intrinsically safe Class B detection circuit for
(2,000 m) or less as permitted by the hazardous location use in those areas classified as hazardous. This feature utilizes one
calculation and application. shunt diode barrier per zone and is FM Approved for Class I, II
and III, Division 1, Groups A, B, C, D, E, F and G; Class I,
Zone 0, AEx ia IIC T6 Ga -29°C ≤ Ta ≤+49°C.
Environmental
• Ambient temperature range:
Standard version (With integrated LCD display) -20° to
120°F (-29° to 49°C) 4-20mA Output Information
LT version (Without integrated LCD display) -40° to Description - The PIM-530 provides two 4-20mA outputs that allow
120°F (-40° to 49°C) for monitoring of the module status and active alarm point location
Standard & LT Versions FM tested to 140°F (60°C) max reading. These outputs are intended for annunciation purposes only.
• Humidity: Max. 95% non-condensing Module monitoring is intended to be accomplished using the on-
board dry contacts connected to a listed or approved fire detection
Indicators control panel initiating device circuit. Consult Manual for detailed
• 4x20 Character LED backlit LCD display output levels for each status loop.
• One green “Power” indicator
Modbus over RS-485 Description
• One red “Alarm” indicator
• One yellow “Fault” indicator The PIM-530 interface module provides integrated Modbus over RS-
485 communications. Each module can be configured as a Modbus
Relay Outputs (Rated 1 amp @ 24VDC Resistive) slave device on an RS-485 network. Once configured to communicate
• One (1) set of Form C (SPDT) Fault Contacts on a network, each module can be polled by a master device for a vari-
• One (1) set of Form C (SPDT) Alarm Contacts ety of module specific data. A master device, such as a PLC (Program-
mable Logic Controller) can monitor the status of one or more
modules and take actions based on their status. Modbus over RS-485
Note: All specifications subject to change without notice. communication is a convenient method for utilizing detector status
Ordering Information information to implement equipment shutdown or other automation
events.
Model No. Description
PIM-530 Interface Module for Protectowire Types PHSC/PLR with LCD display and navigation buttons.
PIM-530E Interface Module for Protectowire Types PHSC/PLR with LCD display and navigation buttons mounted in a
NEMA-4X (IP66) Enclosure.
PIM-530E-I Interface Module with ISB for Protectowire Types PHSC/PLR with LCD display and navigation buttons mounted in a
NEMA-4X (IP66) Enclosure.
PIM-530LT Interface Module for Protectowire Types PHSC/PLR without LCD display and navigation buttons for use in low tempera-
ture environments. This model requires the use of a separately ordered hand-held programmer. Consult Factory for details.
PIM-530LTE Interface Module for Protectowire Types PHSC/PLR without LCD display and navigation buttons, mounted in a NEMA-
4X (IP66) Enclosure. For use in low temperature environments. This model requires the use of a separately ordered hand-
held programmer. Consult Factory for details.
PIM-530LTE-I Interface Module with ISB for Protectowire Types PHSC/PLR without LCD display and navigation buttons, mounted in a
NEMA- 4X (IP66) Enclosure. For use in low temperature environments. This model requires the use of a separately ordered
hand-held programmer. Consult Factory for details.
CTMP-1 Hand-held programmer for PIM-530LT Models. Required for commissioning system, setting alarm temperature and
accessing history log.

The Protectowire Company, Inc. n60 Washington Street, Pembroke, MA 02359 U.S.A. n p:781-826-3878 n f:781-826-2045
web: www.protectowire.com n email: pwire@protectowire.com
© 2018 The Protectowire Co., Inc. SPECIAL HAZARD FIRE DETECTION SYSTEMS DS 9260B-0219 (2C)