HYDROSTAB VALVE

7
T18005B DOWNSTREAM HYDROSTAB PREMIUM REGULATION VALVE
8
T18005B DOWNSTREAM HYDROSTAB PREMIUM REGULATION VALVE
 T18005B DOWNSTREAM HYDROSTAB PREMIUM REGULATION VALVE
Depending on the reduction of pressure desired, it is worth making sure that the device will not be in a cavitation zone.
To determine whether a risk exists, please refer to the graphics below.

MODEL XGS
UPSTREAM PRESSURE in bars

DOWNSTREAM PRESSURE in bars

Zone A: Conditions not including cavitation.

Zone B: Harsh area of use. Make sure you have a polyurethane disk kit.
Zone C: Cavitation zone. Make sure you have an anti-cavitation kit ACD040 or cascaded devices.
In the case of downstream pressure below 1 bar, an air inlet device may be considered (consult us).
Zone D: Impossible zone, upstream pressure lower than downstream pressure.

Hydraulic engineer’s notes:

The potential damage created by cavitation in the regulation valve are detrimental to its service life and
therefore to the precision of the downstream pressure controlled. The anti-cavitation device addresses
this threat. Furthermore, this device only requires the installation of a single device on the network, unlike
some manufacturers’ recommendations (two devices in series). This avoids higher hardware costs, a larger
valve chamber and more complex maintenance.

Request Hydrosize II to help you with the dimensioning of the device!

9
 THE HYDROBLOC SYSTEM ESTABLISHING A PROJECT
OPERATING RANGES

The table below summarises the flow coefficients as well as the flow rates under certain speeds. The Hydrobloc Premium series allows an
exceptional speed, which can be used for flows related to fire-fighting (red zone).

En l/s 1000
En l/s

100

120 m³/h

60 m³/h

40 m³/h
10

20 m³/h
15 m³/h
10 m³/h

5 m³/h

1
3 m³/h

2 m³/h

1 m³/h

0,1
50 XGS

65 XGS

80 XGS

100 XGS

125 XGS

150 XGS

200 XGS

250 XGS

300 XGS
100 XG

125 XG

150 XG

200 XG

250 XG

300 XG
50 XG

65 XG

80 XG

Optimum
Plage de operating range by
fonctionnement DN.
optimale par DN.
The Δp available
La ∆p. disponibleand
et consumable
consommable in the
dansvalve must be
la vanne doitbetween the Δp necessary
être comprise fornécessaire
entre la ∆p. operation of
authe
valve and the maximum
fonctionnement allowable
de la vanne et le (see cavitation
maximum and speed
admissible diagrams).
(voir diagrammes de cavitation et de vitesse).
Range of fonctionnement
Plage de operation underpossible
conditions
sous(please consult
conditions (nousus):
consulter) :
•• XGS: speeds
XGS of between
: vitesses 4 m/s
comprises entreand 6 m/s.
4 m/s et 6 m/s.
•• XG:XG
speeds of between
: vitesses 5 m/s
comprises and5 m/s
entre 7 m/s.
et 7 m/s.
10
Pressure reduction pilot 51P offers several adjustment ranges:
• Standard: 1 to 16 bar
• Option 1: 0.3 to 2 bar (for a reservoir by-pass, for example)
• Option 2: 15 to 25 bar (other ranges: please consult us)
NB: it is possible to modify the range in-situ without changing the regulation valve or the pilot. Only the pilot spring is replaced by
simply removing the pilot bonnet!

DIMENSIONS

MAIN VALVE TYPE XGS DN A (mm) B (mm) C (mm) D (mm) Weight* (kg)
40/50 230 145 195 80 10.2
REDUCED THROUGHWAY 65 290 173 237 95 15
80 310 198 257 102 21
100 350 226 277 112 27
125 400 265 312 127 34
150 480 265 376 145 37
200 600 351 431 172 68
250 730 436 521 205 125
300 850 524 647 232 200

Main valve right body XGS and XG

11
 6 7

5 18

4 10

11 17

13 9 2

12 16

3 8

15

1 14

Part
Name Type Name Number Standard
no.
1 BODY DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
2 MOBILE PARTS Nos. 14-15-16-8-17-18
3 SEAT STAINLESS-STEEL GX5CrNiMo19-11-2 1.4408 EN 10213-4
4 BONNET DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
5 GUIDE BRASS CuZn21Si3P (CR) CW724R EN 12164
6 INDICATOR STAINLESS STEEL X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088
7 SPRING STAINLESS STEEL X5CrNiMo17-12-2 1.4401 EN 10088
8 DISK ELASTOMER EPDM ISO 1629
9 DIAPHRAGM ELASTOMER EPDM ISO 1629
10 O-RINGS ELASTOMER EPDM ISO 1629
11 STUD STAINLESS STEEL A2 ISO 3506
12 WASHER STAINLESS STEEL A2 ISO 3506
13 NUT STAINLESS STEEL A4 ISO 3506
14 SHAFT STAINLESS STEEL X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088
15 DISK RETAINER STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
16 DISK HOLDER STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
17 DIAPHRAGM RETAINER STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
18 NUT STAINLESS STEEL A2 ISO 3506

12
 6 7

5 18

4 10

11 17

13 9 2

16
12
8
3
15

1 14

Part
Name Type Name Number Standard
no.
1 BODY DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
2 MOBILE PARTS Nos. 14-15-16-8-17-18
3 SEAT STAINLESS STEEL GX5CrNiMo19-11-2 1.4408 EN 10213-4
4 BONNET DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
5 GUIDE BRASS CuZn21Si3P (CR) CW724R EN 12164
6 INDICATOR STAINLESS STEEL X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088
7 SPRING STAINLESS STEEL X5CrNiMo17-12-2 1.4401 EN 10088
8 DISK ELASTOMER EPDM ISO 1629
9 DIAPHRAGM ELASTOMER EPDM ISO 1629
10 O-RINGS ELASTOMER EPDM ISO 1629
11 STUD STAINLESS STEEL A2 ISO 3506
12 WASHER STAINLESS STEEL A2 ISO 3506

13 NUT STAINLESS STEEL A4 ISO 3506

14 SHAFT STAINLESS STEEL X5CrNiMo17-12-2 1.4401 EN 10088
15 DISK RETAINER STAINLESS STEEL GX5CrNiMo19-11-2 1.4408 EN 10213-4
16 DISK HOLDER DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
17 DIAPHRAGM RETAINER DUCTILE IRON EN-GJS-500-7 5.3200 EN 1563
18 NUT STAINLESS STEEL A2 ISO 3506

13
T18005B DOWNSTREAM HYDROSTAB PREMIUM REGULATION VALVE

NOMENCLATURE OF THE DOWNSTREAM PILOT CIRCUIT

7
6

5 9

10 4

1
3

Part
Name N.B. Type Name Number Standard
no.
01 Main valve 1 - See detail pages 15-16
02 Filter with G 3/8 screen 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
03 Diaphragm in the filter 02 1 STAINLESS STEEL X2CrNiMo17-12-2 (AISI 316L) 1.4408 EN 10088
CUPRO / STAIN-
04 Ball valve FF G 3/8 3
LESS STEEL - -
05 Pipe connection piece kit 1 STAINLESS STEEL X2CrNiMo17-12-2 (AISI 316L) 1.4408 EN 10088
STAINLESS STEEL
06 Position indicator 1 X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088
/ glass
07 Downstream type pilot 51P 1 - See details page 18 - -
08 Opening retarder OR 1 STAINLESS STEEL - - -
09 Connection cross 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
Pressure-gauge holding valve CUPRO / STAIN-
10
G 3/8
2
LESS STEEL - -
14
 T18005B DOWNSTREAM HYDROSTAB PREMIUM REGULATION VALVE
NOMENCLATURE OF THE DOWNSTREAM PILOT TYPE 51P

10

11

12

13

Part
Name N.B. Type Name Number Standard
no.
01 Protective cap 1 PLASTIC ABS - -

02 Pilot calibrating screw + locknut 1 STAINLESS STEEL A4 - ISO 3506

03 CHc screw 8 STAINLESS STEEL A4 - ISO 3506

04 Pilot cap 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4

05 Calibrating screw supporting plate 1 STAINLESS STEEL X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088

06 Spring 1 to 16 bar 1 STEEL SWOSC-V - JIS G3561

Spring 0.3 to 2 bar (optional) 1 STAINLESS STEEL X10CrNi18-8 (AISI 302) 1.4310 EN 10088
Spring 15 to 25 bar (optional) 1 Please consult us. - - -
07 Diaphragm retaining nut. 1 STAINLESS STEEL A4 - ISO 3506
08 Flange 1 STAINLESS STEEL X5CrNiMo17-12-2 (AISI 316) 1.4401 EN 10088
09 Pilot diaphragm 1 ELASTOMER CLOTH EPDM - ISO 1629
10 Disk holder 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
11 Pilot body 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
12 Disk 1+1 EPDM + STAINLESS STEEL - - ISO 1629
15
13 Plug - pilot guide stop 1 STAINLESS STEEL GX5CrNiMo19-11-2 (CF8M) 1.4408 EN 10213-4
TALIS remains the best choice for water flow management solutions.
Our company provides the best adapted solution for water and energy
management, as well as for industrial or municipal applications. With a
comprehensive range of over 20,000 products, we provide global solutions
for each phase of the water cycle: pumping, distribution, connections, etc.
Our experience, innovative technologies and all-encompassing, in-depth
expertise form the basis for the development of lasting solutions and the
best possible management of the vital resource which is water. BAYARD
ZI - 4 avenue Lionel Terray
CS 70047
69881 Meyzieu cedex France
TEL. +33 (0) 4 37 44 24 24
FAX +33 (0) 4 37 44 24 25
WEBSITE www.bayard.fr

The characteristics and performance data are subject to change without notice as a result
of technical developments. Images and photos are non-binding.

SMA/Bayard/Hydostab/20-01-A4