Texas Instruments - TTL DataBook Vol3

SDAD001A
TheTTL
DataBook
Volume3
1984
~~ ,
. Advanced Low-Pow~r Schottky

Advanced Schottky
"
.--
~
TEXAS
INSTRUMENTS
The TTL Data Book
Volume 3
General Information
1~_A_L_S_a_n_d_A
__ S_C_i_rc_u_it_s__________~~_~
__1II
I~_M_e_c_h_an_i_c_al_D__at_a______________~I@
,
The TTL Data Book

Volutne 3
TEXAS
INSTRUMENTS
IMPORTANT NOTICE
Texas Instruments reserves the right to make changes at

any time in order to improve design and to supply the best
product possible.
TI cannot assume any responsibility for any circuits shown

or represent that they are free from patent infringement.
Information contained herein supersedes data published in

the ALS/AS Logic Circuits Data Book 1983, SDAD001.
ISBN 0-89512-153-0
Library of Congress No. 82-074480
Copyright © 1984 Texas Instrumems Incorporated

INTRODUCTION
In this volume, Texas Instruments presents technical information on the most advanced families of TIL integrated circuits,
Advanced Low-Power Schottky t (ALS), and Advanced Schottky t (AS). The choice provided by selecting from either ALS
or AS functions provides this systems design engineer with a management tools to achieve performance budgeting. Efficient
design parameters can be met easily by taking advantage of this low power of ALS in noncritical paths and using high
performance AS in speed critical paths. The efficiencies realized by ALS and AS are being offered to system designers in
the following forms:
1. Pin-to-pin compatible, plug-in versions of most popular LSTTL and STTL functions.
2. Higher density MSI and LSI functions.
The ease of use of pin-to-pin compatible functions enables designers to upgrade existing TIL based systems with the following
benefits:
• Reduce system power requirements

• Enhance critical system performance
• Improved overall system reliability
New system designs can can capitalize on both the improved efficiency of the pin-compatible devices and the higher densities
of the MSI/LSI series of devices, such as the' ALS632 32-bit parallel error detection and connection circuitry, with the following
system benefits:
• Reduced system component count

• Expanded functional capabilities
• Improved levels of cost effectiveness
• DC and AC specifications across the full rated supply voltage and temperature ranges with AC specifications
at 50 pF loading.
ALS and AS devices utilize an advanced wafer fabrication process that includes ion-implanted transistors, oxide isolations,
and composed mask sets. This process is coupled with circuit design techniques to implement the following:
• Improve input threshold and noise margins

• Improve line driving and receiving
• Maintain or increase drive capability
• Increase density of LSI functions
• Implement universal logic solutions
• Take advantage of new packaging
- 24-pin 300-mil DIP
- Ceramic and plastic chip carriers
The ALS/AS family will grow to well over 300 devices through the end of 1984. Included among the new functions are:
• 16-bit by 16-bit universal multiplier

• 20-MHz 8-bit-slice universal processor element with on-board register file
• 20-MHz 14-bit controller with 9-word stack
• 20-MHz 16-bit barrel shifter
• Many additional pin-compatible ALS and AS devices
Included in this volume is a Functional Index to all bipolar digital devices types available or under development showing
the available technologies for each type (Standard TTL, Schottky, Low-Power Schottky, Advanced Low-Power Schottky,
Advanced Schottky, etc.). Logic symbols prepared in accordance with IEEE activity and pin assignments for all bipolar devices
are shown in the Product Guide section of Volume 1 with typical performance data and chip carrier information. Package
dimensions given in the Mechanical Data section of this book are in metric measurement (and parenthetically in inches),
which should simplify board layout for designers involved in metric conversion and new designs.
While this volume offers design and specif[cation data for bipolar Advanced Low-Power Schottky (ALS) and Advanced Schottky
(AS) components, complete technical data for any TI semiconductor product is available from your nearest TI field sales
office, local authorized TI distributor, or by writing direct to: Marketing and Information Services, Texas Instruments
Incorporated, P.O. Box 225012, MS 308, Dallas, Texas 75265.
tlntegrated Schottky-Barrier diode-clamped transistor is patented by Texas Instruments, U.S. Patent Number 3.463,975.
v
vi
The TTL Data Book
Volume 3
I~_G_e_n_e_ra_I_ln_f_o_rm__a_ti_o_n____________~II__1II
·~I_A_L_S_a_n_d~A_S_.·_C_ir_cu~i_ts_·__~~____··_.~_~
IL-:_M_e_c_h_an_i_c_ClI_.• O_·._at_a_···~_ _. _.~~................

_.
1-1
III
C)
m
2
m
::IJ
»
r-
2
."
o
::IJ
S
»
:::1
o
2·
1-2
NUMERICAL INDEX
NUMERICAL INDEX
SN54ALSOOA SN74ALSOOA ................ 2-3 SN54ALS153 SN74ALS153 ............... 2-125

SN54ASOO SN74ASOO .0 2-3
•••••••••••••••• SN54AS153 SN74AS153 • •••• , ••••••• 0. 2-125
SN54ALS01 SN74ALS01 .................. 2-7 SN54ALS157 SN74ALS157 ............... 2-129
SN54ALS02 SN74ALS02 .................. 2-9 SN54AS157 SN74AS157 ............... 2-129
SN54AS02 SN74AS02 .................. 2-9 SN54ALS158 SN74ALS158 ............... 2-129
SN54ALS03A SN74ALS03A . ........... -,. 2-13 SN54AS158 SN74AS158 ............... 2-129
SN54ALS04A SN74ALS04A . .............. 2-15 SN54ALS160A SN74ALS160A ............. 2-137
..
SN54AS04 SN74AS04 .. ........ ....... 2-15 SN54AS160 SN74AS160 •• •• 0 ••••• , •••• 2-137
SN54ALS05A SN74ALS05A ................ 2-19 SN54ALS161A SN74ALS161A . ............ 2-137
SN54ALS08 SN74ALS08 ................. 2-21 SN54AS161 SN74AS161 ' " ............ 2-137
SN54AS08 SN74AS08 ................. 2-21 SN54ALS162A SN74ALS162A · ............ 2-137
SN54ALS09 SN74ALS09 ................. 2-25 SN54AS162 SN74AS162 •••• 0 •••• ,_ •••• 2-137
SN54ALS10 SN74ALS10 ................. 2-27 SN54ALS163A SN74ALS163A · , ........... 2-137
SN54AS10 SN74AS10 ................. 2-27 SN54AS163 SN74AS163 ..0 ..... , ...... 2-137
SN54ALS11
SN54AS11
SN74ALS11 ................. 2-31
SN74AS11 ................. 2-31
SN54ALS164
SN54ALS165
SN74ALS164 ...............
SN74ALS165 ...............
2-147
2-151
Z
SN54ALS12 SN74ALS12 ................. 2-35 SN54ALS166 SN74ALS166 ............... 2-153
0
SN54ALS15 SN74ALS15 ................. 2-37 SN54ALS168A SN74ALS168A · , - .......... 2-157 i=
SN54ALS20A SN74ALS20A ••••••••••••• 2-39
SN74AS20 ................. 2-39
0. SN54AS168 SN74AS168 . ...... , ....... 2-157 «
SN54AS20
SN54ALS21 SN74ALS21 ................. 2-43
SN54ALS169A
SN54AS169
SN74ALS169A • ••••• 0
SN74AS169 • • • • • • • • , ' · . 0 • •
•••• ,_ 2-157
2-157 ~
SN54AS21 SN74AS21 ............. , ... 2-43 SN54ALS174 SN74ALS174 ............... 2-167 a:
SN54ALS22A SN74ALS22A ........ ....... 2-47 SN54AS174 SN74AS174 ............... 2-167 0
SN54ALS27 SN74ALS27 ................. 2-49 SN54ALS175 SN74ALS175 ............... 2-167 LL
SN54AS27 SN74AS27 ................. 2-49 SN54AS175 SN74AS175 - .............. 2-167 Z
SN54ALS28A SN74ALS28A ............... 2-53 SN54AS181A SN74AS181A . ............. 2-173
SN74AS182 ............... -I
SN54ALS30
SN54AS30
SN54ALS32
SN74ALS30 ................. 2-55
SN74AS30 ................. 2-55
SN74ALS32 ................. 2-59
SN54AS182
SN54ALS190
SN54ALS191
SN7 4ALS 190 ...............
SN74ALS191 ...............
2-185
2-189
2-189
«
a:
SN54AS32 SN74AS32 ................. 2-59 SN54ALS192 SN74ALS192 ............... 2-197 W
SN54ALS33A SN74ALS33A ........ ....... 2-63 SN54ALS193 SN74ALS193 ............... 2-197 Z
SN54ALS34 SN74ALS34 ................. 2-65 SN54AS194 SN74AS194 ............... 2-205 W
SN54AS34 SN74AS34 ................. 2-65 SN54AS195 SN74AS195 . .............. 2-211 c;,
SN54ALS35 SN74ALS35 ................. 2-69 SN54AS230 SN74AS230 ............... 2-213
SN54ALS37A SN74ALS37A .............. . 2-71 SN54AS231 SN74AS231 ............... 2-213
SN54ALS38A SN74ALS38A .............. . 2-73 SN54ALS240A SN74ALS240A ............. 2-217
SN54ALS40A SN74ALS40A ............... 2-75 SN54AS240 SN74AS240 . .............. 2-217
SN54ALS74 SN74ALS74 ................. 2-77 SN54ALS241A SN74ALS241A . ............ 2-217
SN54AS74 SN74AS74 ................. 2-77 SN54AS241 SN74AS241 . .............. 2-217
SN54ALS86 SN74ALS86 ................. 2-81 SN54ALS242A SN74ALS242A ............. 2-223
SN54AS95 SN74AS94 .. ............... 2-83 SN54AS242 SN74AS242 ............... 2-223
SN54ALS109 SN74ALS109 ................ 2-87 SN54ALS243A SN74ALS243A ............. 2-223
SN54AS109 SN74AS109 ~................ 2-87 SN54AS243 SN74AS243 ............... 2-223
SN54ALS 112A SN74ALS112A ...... ..... ... 2-91 SN54ALS244A SN74ALS244A · ............ 2-229
SN54AS112 SN74AS112 ................ 2-91 SN54AS244 SN74AS244 . ..... , ........ 2-229
SN54ALS 113A SN7 4ALS 113A .............. 2-95 SN54ALS245A SN74ALS245A . ............ 2-235
SN54AS113 SN74AS113 ............. ' " 2-95 SN54AS245 SN74AS245 ............... 2-235
SN54ALS 114A SN74ALS114A .... .......... 2-99 SN54AS250 SN74AS250 ............... 2-241
SN54AS114 SN74AS114 ................ 2-99 SN54ALS251 SN74ALS251 ............... 2-245
SN54ALS131 SN74ALS131 ............... 2-103 SN54AS251 SN74AS251 ............... 2-245
SN54AS131 SN74AS131 ............... 2-103 SN54ALS253 SN74ALS253 ............... 2-251
SN54ALS137 SN74ALS137 ............... 2-109 SN54ALS257 SN74ALS257 ............... 2-255
SN54AS137 SN74AS137 . ..... ......... 2-109 SN54AS257 SN74AS257 ............... 2-255
SN54AS138 SN74AS138 ............... 2-113 SN54AS258 SN74AS258 . .............. 2-255
SN54AS151 SN74AS151 ........ ....... 2-121 SN54AS280 SN74AS280 ............... 2-273
TEXAS 1-3
INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEXAS 75265
NUMERICAL INDEX
NUMERICAL INDEX
SN54AS282 SN74AS282 ............... 0 2-277 SN54ALS620A SN74ALS620A .0.0 ••••••• 0. 2-415

SN54AS286 SN74AS286 •••••• 0 ••••• 0 •• 2-281 SN54AS620 SN74AS620 .0.0.0 •••••••• 0 2-415
SN54AS298 SN74AS298 ............... 2-287 SN54ALS621A SN74ALS621A .0.0 •• 0 •••••• 2-415
SN54ALS299 SN74ALS299 ............... 2-291 SN54AS621 SN74AS621 '0 •••••••• 0 ••• 0 2-415
SN54AS299 SN74AS299 •••••••••• • ••• 0 2-291 SN54ALS622A SN74ALS622A ••••••• 0 ••••• 2-415
SN54ALS323 SN74ALS323 ............... 2-291 SN54AS622 SN74AS622 .0 ••••••••••••• 2-415
SN54AS323 SN74AS323 ••• 0 •••• 0 '_0 .0. 2-291 SN54ALS623A SN74ALS623A . ............ 2-415
SN54ALS352 SN74ALS352 ............... 2-301 SN54AS623 SN74AS623 .0 •••••••••••• 0 2-415
SN54AS352 SN74AS352 •••••••••••••• 0 2-301 SN54ALS632 SN74ALS632 ............... 2-425
SN54AS353 SN74AS353 •••••••••••••• 0 2-305 SN54ALS634 SN74ALS634 ............... 2-425
III
G)
SN54ALS365
SN54ALS366
SN54ALS367
SN54ALS368
SN74ALS365 ...............
SN74ALS366 ...............
SN74ALS367 ...............
SN74ALS368 ...............
2-309
2-309
2-309
2-309
SN54ALS635
SN54ALS638A
SN54AS638
SN54ALS639A
SN74ALS635 ...............
SN74ALS638A .0.0
SN74AS638 ...............
SN74ALS639A .............
•• 0 ••••••
2-425
2-439
2-439
2-439
m SN54ALS373
SN54AS373
SN74ALS373 ...............
SN74AS373
2-313
2-313
SN54AS639
SN54ALS640A
SN74AS639
SN74ALS640A
.0 •••••••••••• 0 2-439
2 •••••••••••••• 0 •••••••••••• 0 2-445
m SN54ALS374
SN54AS374
SN74ALS374 ...............
SN74AS374
2-319
2-319
SN54AS640
SN54ALS641A
SN74AS640 ••••••••••••••
SN74ALS641A . ............
0 2-445
2,-445
:XJ ••• 0 ••• •• ••••••
»
r-
SN54AS395
SN54ALS465A
SN74AS395
SN74ALS465A
••••••••••••••
0 •••• 0 ••••••
0
0
2-327
2-327
SN54AS641
SN54ALS642A
SN74AS641 .0.0 ••••
SN74ALS642A .0.·0 • • • . • • • .
0 •• 0.0. 2-445
2-445
SN54ALS466A SN74ALS466A '0' •••••••••• 2-327 SN54AS642 SN74AS642 .0.0".0 •••••••• 2-445 .
SN54ALS467A SN74ALS467A 2-327 SN54ALS643A SN74ALS643A . ............ 2-445
2 SN54ALS468A SN74ALS468A
•• 0 •••• 0 •••••
2-327 SN54AS643 SN74AS643 2-445

'"T1 SN54ALS518
.0
SN74ALS518 ...............
•••••••• 0 '0
2-333
.0'.0 ••••••• 0 ••
SN54ALS644A SN74ALS644A 2-445

0 SN54ALS519 SN74ALS519 ............... 2-333 SN54AS644
.0 ••
SN74AS644 ............... '

0 ••••••••
2-445
:XJ SN54ALS520 SN74ALS520 ............... 2-333 SN54ALS645A SN74ALS645A 2-445
S
••••••••• 0 •• 0
SN54ALS521 SN74ALS521 ............... 2-333 SN54AS645 SN74AS645 2-445

»
.0.0 •• 0 ••••••••

SN54ALS526 SN74ALS526 ............... 2-339 SN54AS646 SN74AS646 2-455
:::! SN54ALS527 SN74ALS527 ............... .2-339 SN54ALS647
.0.0
SN74ALS647 ...............
•••••••••• 0
2-455
0 SN54ALS528 SN74ALS528 ............... 2-339 SN54ALS648 SN74ALS648 ............... 2-455
2 SN54ALS533 SN74ALS533 ............... 2-345 SN54AS648 SN74AS648 .0 ••••••••••••• 2-455
SN54AS533 SN74AS533 ••••••• 0 ••••••• 2-345 SN54ALS649 SN74ALS649 ......... , ..... 2-455
SN54AS534 SN74AS534 •••••• 0 •••••••• 2-351 SN54AS651 SN74AS651 . .............. 2-465
SN54ALS560A SN74ALS560A ............. 2-369 SN54ALS677 SN74ALS677 ............... 2-475
SN54AS573 SN74AS573 ••••••••• 0 ••••• 2-397 SN54AS757 SN74AS757 . .............. 2-491
SN54AS574 SN74AS574 ............... 2-403 SN54AS759 SN74AS759 . .......... , ... 2-495
SN54AS576 SN74AS576 •••• 0 •••••••••• 2-409 SN54AS800 SN74AS800 . .............. 2-505
SN54ALS577 SN74ALS577 ............... 2-409 SN54AS802 SN74AS802 ............. ,. 2-509
SN54AS577 SN74AS577 . . . . . . . . . . . . . . . 2-409 SN54ALS804 SN74ALS804 ............... 2-513
SN54ALS580 SN74ALS580 ............... 2-397 SN54AS804A SN74AS804A ••• 0 •••••••••• 2-513
SN54AS580 SN74AS580 ............... 2-397 SN54ALS805 SN74ALS805 ............... 2-517
SN54AS805A SN74AS805A . . . . . . . . . . . . . . 2-517
1-4 TEXAS
INSTRUMENTS
NUMERICAL INDEX
NUMERICAL INDEX
SN54ALSS08 SN74ALSS08 ............... 2-521 SN54AS881A SN74AS881A ••••••• 0.0 •••• 2-649
SN54AS80SA SN74AS80SA ' 0 , • • • • • • • • • • 0 2-521 SN54AS882 SN74AS8S2 •• 0.0 ••• 0.0 •••• 2-651
SN54ASS21 SN74AS821 ••• 0 •••••• 0 •• 0. 2-525 SN54AS885 SN74AS885 • •••••• 0 •• 0.0 •• 2-657
SN54AS822 SN74AS822 ••• 0.0 •• 0 •••••• 2-525 SN54ALS1000A SN74ALS1000A •• 0.0 •• 0 .0 •• 2-663
SN54AS823 SN74ASS23 • ••••••• 0 ••••• 0 2-531 SN54AS1000 SN74AS1000 .0.0 ••• 0.0.0 •• 2-663
SN54AS824 SN74AS824 • ••••••• 0. 0 •••• 2-531 SN54ALS1002A SN74ALS1002A .0.··0.0 .... 2-667
SN54AS825 SN74AS825 ••••••• 0 ••••••• 2-537 SN54ALS1003A SN74ALS1003A .0 ••• 0 ••• 0 •• 2-669
..
SN54ASS26 SN74AS826 ...... ......... 2-537 SN54ALS1004 SN74ALS1004 .............. 2-671
SN54ALSS32 SN74ALS832 ............... 2-543 SN54AS1004 SN74AS1004 ••••••• 0'0 .0 •• 2-671
SN54AS832A SN74AS832A •••••••••••• 0. 2-543 SN54ALS1005 SN74ALS1005 .............. 2-675
SN54ALSS41 SN74ALSS41 ............... 2-547 SN54ALS1008A SN74ALS1008A .0 ••• 0.0 •• 0 • 2-677
SN54AS841 SN74AS841 ............... 2-547 SN54AS1008 SN74AS100S .0.0 •• 0 •• 0 •• 0. 2-677
SN54ALS842 SN74ALSS42 ............... 2-547 SN54ALS1010A SN74ALS1010A . 0 . ' 0 ' '0 • • 0 . 2-681
SN54ASS42 SN74AS842 ............... 2-547 SN54ALS 1011 A SN74ALS1011A ..0 •• 0.0 •• 0 • 2-6S3
SN54ALS843 SN74ALSS43 ............... 2-555 SN54ALS1020A SN74ALS1020A .0 ••• 0 ••• 0 •• 2-685 2
SN54AS843 SN74AS843 ............... 2-555 SN54ALS1032A SN74ALS1032A 2-6S7
SN54ALS844, SN74ALSS44 ............... 2-555 SN54AS1032
.0
SN74AS1032 .0.0.··0.0 ••••

••• 0.0 ••••
2-687 0
SN54AS844 SN74AS844 • .0 •• 0.0 ••••••• 2-555 SN54ALS1034 SN74ALS1034 .............. 2-691 ~
SN54ALSS45 SN74ALS845 ............... 2-563 SN54AS1034 SN74AS1034 •••••• 0 •• 0 •••• 2-691 <C
SN54AS845 SN74AS845 ......... ...... 2-563 SN54ALS1035 SN74ALS1035 .............. 2-695
SN54ALS846 SN74ALS846 ............... 2-563 SN54AS1036 SN74AS1036 2-697 2
SN54AS846 SN74AS846 2-563 SN54ALS1240
.0 ••••
SN74ALS1240 ..............
0 •• 0 ••••
2-699 a:
0
• .0 ••••••••••••
SN54AS850 SN74AS850 • .0 •• 0 '0' •••••• 2-571 SN54ALS1241 SN74ALS1241 .............. 2-699

SN54AS851 SN74AS851 •• 0 •• 0.0 ••••••• 2-571 SN54ALS 1242 SN74ALS1242 ............ '.. 2-703 LL
SN54AS852 SN74AS852 ···0.0.0 ....... 2-581 SN54ALS 1243 SN74ALS1243 .............. 2-703 2
SN54AS856 SN74AS856 • . 0 • • • ' 0 • • • • • • • 2-587 SN54ALS1244A SN74ALS1244A .0 ••• 0.0 .0 •• 2-707
SN54ALSS57 SN74ALS857 ............... 2-593 SN54ALS1245 SN74ALS1245 .............. 2-711 ..J
SN54ASS57 SN74AS857 • .0 •• 0 •• 0 ••••• 0 2-593 SN54ALS1620 SN74ALS1620 .............. 2-715 <C
SN54ASS66 SN74AS866 •• 0 •• 0.0 ••••••• 2-601 SN54ALS1621 SN74ALS1621 .............. 2-715 a:
SN54ASS67 SN74ASS67 • .0 •••••••••••• 2-607 SN54ALS1622 SN74ALS1622 .............. 2-715 W
SN54ASS69 SN74AS869 .. .... ......... 2-607 SN54ALS 1623 SN74ALS1623 .............. 2-715 2
SN54ASS70 SN74AS870 ...... ..... .... 2-613 SN54ALS 1638 SN74ALS1638 .............. 2-721 W
SN54AS871 SN74AS871 · .............. 2-613 SN54ALS 1639 SN74ALS1639 .............. 2-721 (!'
SN54ALSS73 SN74ALS873 ............... 2-619 SN54ALS 1640A SN74ALS1640A ............ 2-725
SN54ASS73 SN74AS873 ............... 2-619 SN54ALS1641 SN74ALS1641 .............. 2-725
SN54ALS874 SN74ALS874 ............... 2-625 SN54ALS1642 SN74ALS1642 .......... ~ ... 2-725
SN54AS874 SN74AS874 · .............. 2-625 SN54ALS1643 SN74ALS1643 .............. 2-725
SN54ALSS76 SN74ALS876 ............... 2-625 SN54ALS1644 SN74ALS1644 .............. 2-725
SN54ASS76 SN74AS876 · .............. 2-625 SN54ALS1645A SN74ALS1645A . ........... 2-725
SN54AS877 SN74AS877 · .............. 2-631 SN54AS2620 SN74AS2620 . ............. 2-731
SN54ALSS78 SN74ALSS78 ............... 2-637 SN54AS2623 SN74AS2623 .............. 2-731
SN54AS878 SN74AS878 ............... 2-637 SN54AS2640 SN74AS2640 . ............. 2-735
SN54ALSS79 SN74ALSS79 ............... 2-637 SN54AS2645 SN74AS2645 .............. 2-735
SN54ASS79 SN74AS879 · .............. 2-637 SN54ALS8003 SN74ALSS003 .............. 2-739
SN54ALSS80 SN74ALSS80 ............... 2-643
SN54AS8S0 SN74ASS80 ............... 2-643
TEXAS 1-5
INSTRUMENTS
GLOSSARY
ALS/AS TTL SYMBOLS. TERMS. AND DEFINITIONS
INTRODUCTION
These symbols, terms, and definitions are in accordance with those currently agreed upon by the JEDEC Council of the
Electronic Industries Association (EIA) for use in the USA and by the International Electrotechnical Commission (lEC)
for international use.
PART I - OPERATING CONDITIONS AND CHARACTERISTICS (IN SEQUENCE BY LETTER SYMBOLS)
f max Maximum clock frequency

The highest rate at which the clock input of a bistable circuit can be driven through its required sequence
while maintaining stable transitions of logic level at the output with input conditions established that should
cause changes of output logic level in accordance with the specification.
III
C)
ICC Supply current
The current into* the VCC supply terminal of an integrated circuit.
m
2: ICCH Supply current, outputs high
m The current into* the VCC supply terminal of an integrated circuit when all (or a specified number) of the
:xJ
»
r-
outputs are at the high level.
ICCL Supply current, outputs low

2: The current into* the VCC supply terminal of an integrated circuit when all (or a specified number) of the
'"TI outputs are at the low level.
0
:xJ IIH High-level input current
S The current into*an input when a high-level voltage is applied to that input.
»
::! IlL Low-level input current
0 The current into* an input when a low-level voltage is applied to that input.
2:
10H High-level output current
The current into* an output with input conditions applied that, according to the product specification, will
establish a high level at the output.
10L Low-level output current

The current into* an output with input conditions applied that, according to the product specification, will
establish a low level at the output.
lOS Short-circuit output current

The current into* an output when that output is short-circuited to ground (or other specified potential) with
input conditions applied to establish the output logic level farthest from ground potential (or other specified
potential).
10ZH Off-state (high-impedance-state) output current (of a three-state output) with high-level voltage applied
The current flowing into* an output having three-state capability with input conditions established that,
according tel the product specification, will establish the high-impedance state at the output and with a high-
level voltage applied to the output.
NOTE: This parameter is measured with other input conditions established that would cause the output to
be at a low level if it were enabled.
* Current out of a terminal is given as a negative value.
1-6 TEXAS
INSTRUMENlS
GLOSSARY
ALS/AS TTL SYMBOLS, TERMS, AND DEFINITIONS
IOZl Off-state (high-impedance-state) output current (of a three-state output) with low-level voltage applied
The current flowing into* an output having three-state capability with input conditions established that,
according to the product specification, will establish the high-impedance state at the output and with a low-
level voltage applied to the output.
NOTE: This parameter is measured with other input conditions established that would cause the output to
be at a high level if it were enabled.
High-level input voltage
..
An input voltage within the more positive (less negative) of the two ranges of values used to represent the
binary variables.
NOTE: A minimum is specified that is the least-positive value of high-level input voltage for which operation
of the logic element within specification limits is guaranteed.
Input clamp voltage

An input voltage in a, region of relatively low differential resistance that serves to limit the input voltage swing. Z
o
low-level input voltage
i=
An input voltage level within the less positive (more negative) of the two ranges of values used to represent
the binary variables.
«
NOTE: A maximum is specified that is the most-positive value of low-level input voltage for which operation
:!
a:
of the logic element within specification limits is guaranteed.
o
u..
VOH High-level output voltage Z
The voltage at an output terminal with input conditions applied that, according to the product specification,
..J
will establish a high level at the output.
«
a:
VOL low-level output voltage w
The voltage at an output terminal with input conditions applied that, according to the product specification, z
will establish a low level at the output. w
C!)
ta Access time
The time interval between the application of a specific input pulse and the availability of valid signals at an
output.
tdis Disable time (of a three-state output)

The time interval between the specified reference points on the input and output voltage waveforms, with the
three-state output changing from either of the defined active levels (high or low) to a high-impedance (off)
state. (tdis = tpHZ or tpLZ).
ten Enable time (of a three-state output)

The time interval between the specified reference points on the input and output voltage waveforms, with the
three-state output changing from a high-impedance (off) state to either of the defined active levels (high or
low). (ten = tpZH or tpzU.
*Current out of a terminal is given as a negative value.
TEXAS 1-7
INSfRUMENlS
GLOSSARY
th Hold time
The time interval during which a signal is retained at a specified input terminal after an active transition occurs
at another specified input terminal.
NOTES: 1. The hold time is the actual time interval between two signal events and is determined by the
system in which the digital circuit operates. A minimum value is specified that is the shortest
interval for which correct operation of the digital circuit is guaranteed.
2. The hold time may have a negative value in which case the minimum limit defines the longest
interval (between the release of the signal and the active ~ransition) for which correct operation
..
of the digital circuit is guaranteed.
tpd Propagation delay time

The time between the specified reference points on the input and output voltage waveforms with the output
changing from one defined level (high or low) to the other defined level. (ted = tpHL or tpLH)'
G') tpHL Propagation delay time, hlgh-to-Iow-Ievel output

m The time between the specified reference points on the input and output vo'itage waveforms with the output
:2 changing from the defined high level to the defined low level.
m
::c tpHZ Di~able time (of a three-state output) from high level
l> The time interval between the specified reference points on the input and output voltage waveforms with the
r- three-state output changing fr~m the defined high level to a high-impedance (off) state.
:2 tpLH Propagation delay time, low-to-high-Ievel output
-n The time between the specified reference points on the input and output voltage waveforms with the output
0
::c changing from the defined low level to the defined high level.
s:
l>
tpLZ Disable time (of a three-state output) from low level
The time interval between the' specified reference points on the input and output voltage waveforms with the
:::! three-state output changing from the defined low level to a high-impedance (off) state.
0
:2 tpZH Enable time (of a three-state output) to high level
The time interval between the specified reference points on the input and output voltage waveforms with the
three-state output changing from a high-impedance (off) state to the defined high level.
tpZL Enable time (of a three-state output) to low level

The time interval between the specified reference points on the input and output voltage waveforms with the
three-state output changing from a high-impedance (off) state to the defined low level.
tsr Sense recovery time

The time interval needed to switch a memory from a write mode to a read mode and to obtain valid data
signals at the output.
tsu Setup time

The time interval between the application of a signal at a specified input terminal and a subsequent active
transition at another specified input terminal.
NOTES: 1. The setup time is the actual time interval between two signal events and is determined by the
system in which the digital circuit operates. A minimum value is specified that is the shortest
interval for which correct operation of the digital circuit is guaranteed.
2. The setup time may have a negative value in which case the minimum limit defines the longest
interval (between the active transition and the application of the other signal) for which correct
operation of the digital circuit is guaranteed.
Pulse duration (width)

The time interval between specified reference points on the leading and trailing edges of the pulse waveform.
'-8 TEXAS
INSTRUMENTS
GLOSSARY
PART II - CLASSIFICATION OF CIRCUIT COMPLEXITY
Gate Equivalent Circuit
A basic unit-of-measure of relative digital-circuit complexity. The number of gate equivalent circuits is that number of
individual logic gates that would have to be interconnected to perform the same function.
large-Scale Integration, lSI
A concept whereby a complete major subsystem or system function is fabricated as a single microcircuit. In this
context a major subsystem or system, whether digital or linear, is considered to be one that contains 100 or more
equivalent gates or circuitry of similar complexity.
Medium-Scale Integration, MSI
A concept whereby a complete subsystem or system function is fabricated as a single microcircuit. The subsystem or
system is smaller than for LSI, but whether digital or linear, is considered to be one that contains 12 or more equivalent
..2:
o
i=
gates or circuitry of similar complexity. «
:!
Small-Scale Integration, SSI a:
Integrated circuits of less complexity. than medium-scale integration (MSI).
ou.
2:
Very-large-Scale Integration, YlSI
..J
The description of any IC technology that is much more complex than large-scale integration (LSI), and involves a much «
a:
higher equivalent gate count. At this time an exact definition including a minimum gate count has not been w
standardized by JEDEC or the IEEE. 2:
w
(!;l
TEXAS 1-9
INSTRUMENTS
EXPLANATION OF FUNCTION TABLES
The following symbols are used in function tables on TI data sheets:
H high level (steady state)

L low level (steady state)
t transition from low to high level
transition from high to low level
-+- value/level or resulting value/level is routed to indicated destination
1m
G)
"
X
value/level is re·entered
irrelevant (any input, including transitions)
m z off (high·impedance) state of a 3·state-output
Z
m a .. h the level of steady-state inputs at inputs A through H respectively
:c 00 level of 0 before the indicated steady-state input conditions were established
:t> complement of 00 or level of n before the indicated steady-state input conditions were established
r- O:o
tort
2 On level of 0 before the most recent active transition indicated by
~ JL one high-level pulse
0 LJ one low-level pulse
:c
s:
:t>
TOGGLE each output changes to the complement of its previous level on each active transition indicated by
tor t.
::!
0
z
If, in the input columns, a row contains only the symbols H, L, and/or X, this means the indicated output is valid when-
ever the input configuration is achieved and regardless of the sequence in which it is achieved_ The output persists so
long as the input configuration is maintained.
If, in the input columns, a row contains H, L, and/or X together with t and/or t, this means the output is valid when-
ever the input configuration is achieved but the transition(s) must occur following the achievement of the steady-state
levels. If the output is shown as a level (H, L, 00, or 00), it persists so long as the steady-state input levels and the
levels that terminate indicated transitions are maintained. Unless otherwise indicated, input transitions in the opposite
direction to those shown have no effect at the output. (If the output is shown as a pulse, JL or L.f, the pulse
follows the indicated input transition and persists for an interval dependent on the circuit.)
1-10 TEXAS
INSTRUMENlS
POST OFFICE BOX 225012 • DALLAS, TEXAS 75265
EXPLANATION OF FUNCTION TABLES
Among the most complex function tables in this book are those of the shift registers. These embody most of the
symbols used in any of the function tables, plus more. Selow is the function table of a 4-bit bidirectional universal
shift register, e.g., type SN74194.
FUNCTION TABLE
INPUTS OUTPUTS
MODE SERIAL PARALLEL
CLEAR -S1 SO
CLOCK
LEFT RIGHT A B C 0 °A °B Oc 00
..
l X X X X X X X X X l l l l
H X X l X X X X X X °AO Oso QCO 000
H H H t X X a b c d a b c d
H l H t X H X X X X H QAn QS n QCn
H L H t X l X X X X L QAn OSn QCn
H H l t H X X X X X QS n °Cn QO n H
Z
H
H
H
L
l
L X
t L
X
X
X
X
X
X
X
X
X
X
X
QS n °Cn QO n
QAO QSO QCO QOO
l
o
i=
«
The first line of the table represents a synchronous clearing of the register and says that if clear is low, all four outputs :2E
will be reset low regardless of the other inputs. In the following lines, clear is inactive (high) and so has no effect. a:
oLL
The second line shows that so long as the clock input remains low (while clear is high), no other input has any effect
Z
and the outputs maintain the levels they assumed before the steady-state combination of clear high and clock low was
established. Since on other lines of the table only the rising transition of the clock is shown to be active, the second line ..J
implicitly shows that no further change in the outputs will occur while the clock remains high or on the high-to:low
transition of the clock.
«
a:
w
The third line of the table represents synchronous parallel loading of the register and says that if S1 and SO are both
zw
high then, without regard to the serial input, the data entered at A will be at output OA, data entered at S will be at C!J
OS, and so forth, following a low-to-high clock transition.
The fourth and fifth lines represent the loading of high- and low-level data, respectively, from the shift-right serial input
and the shifting of previously entered data ~ne bit; data previously at OA is now at OS, the previous levels of Os and
Oc are now at Oc and OD respectively, and the data previously at OD is no longer in the register. This entry of serial
data and shift takes place on the low-to-high transition of the clock when S1 is low and SO is high and the levels at
inputs A through D have no effect.
The sixth and seventh lines represent the loading of high- and low-level data, respectively, from the shift-left serial input
and the shifting of previously entered data one bit; data previously at Os is now at OA, the previous levels of Oc and
OD are now at Os and OC, respectively, and the data previously at OA is no longer in the register. This entry of serial
data and shift takes place on the low-to-high transition of the clock when S1 is high and SO is low and the levels at
inputs A through D have no effect.
The last line shows that as long as both mode inputs are low, no other input has any effect and, as in the second line,
the outputs maintain the levels they assumed before the steady-state combination of clear high and both mode inputs
low was established.
TEXAS 1-11
INSTRUMENTS
SERIES 54ALS/74ALS AND 54AS/74AS DEVICES
PARAMETER MEASUREMENT INFORMATION
7V
VCC
S1
t RL = R1 = R2
FROM OUTPUT
UNDER TEST ; , q P O I N T
TEST
FROM OUTPUT h TEST
UNDER TEST T p O I N T R1
I
CL RL FROM OUTPUT~~-4___-'_-O TEST
--
(See Note A) CL UNDER TEST POINT
"~N".AI CL
(See Note A)
R2
'='
G) LOAD CIRCUIT FOR

m BI-STATE LOAD CIRCUIT FOR LOAD CIRCUIT FOR
:2 TOTEM-POLE OUTPUTS OPEN-COLLECTOR OUTPUTS THREE-STATE OUTPUTS
m
:c
»
r-
NOTE A. CL includes probe and jig capacitance.
:2
"T1 TIMING ./. 3.5 V HIGH-LEVEL~----3.5V
o INPUT /f1.3V
___....J.:_ - - - -- --0.3 V
PULSE ,1.3 V 1.3 V I
0.3 V
:c I
- - tw -
I
s: :- tsu ....J- th i : - - tw --1 3.5 V

» DATA
INPUT J
~1-'l~/-3.5V
1.3 V ~
LOW-LEVEL~1.3V ··1.3V~
~---0.3V
::! 0.3 V PULSE
o VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS

:2 SETUP AND HOLD TIMES PULSE WIDTHS
INPUT p.3 I
V
I
-
~.3 V -
-
-
-3.5V
0.3 V
OUTPUT ~3.5V
CONTROL
!low-level
1.3 V
I
1.3 V
enabling) I -1-------0.3 V
:.- tPLH 41 f.- tpHL ~ tPZL~ -.! ~tPLZ
INPHAS~I I : -:--VOH I I II
~
OUTPUT: 1.3 V I 1.3 V Il II "'3.5 V
I vOL
WAVEFORM 1 I 1.3 V.f. I I 0.3 V
I I S1 CLOSED -=-------::."f=
I I VOL
,....tPHL-.j I'"-tPLH'"
(See Note B) --.I
tPZH~ ~tPHZ
~
:
~~~p~/HASE 1.3 V
:VOH
1.3 V
WAVEFORM 2 I -----=--=-{ VOH
S10PEN 1.3 V 0.3 V
- - -VOL
(See Note D) (See Note B)
"'0 V
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES ENABLE AND DISABLE TIMES, THREE-STATE OUTPUTS
NOTES: B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses have the following characteristics: PRR';;; 1 MHz. tr = tf = 2 ns. duty cyle = 50%.
D. When measuring propagation delay times of 3-state outputs. switch S1 is open.
1-12 TEXAS
INSTRUMENTS
SERIES 54ALS/74ALS
ADVANCED LOW·POWER SCHOTTKY TRANSISTOR·TRANSISTOR LOGIC
TYPICAL CHARACTERISTICSt
'ALSOOA 'ALSOOA
PROPAGATION DELAY TIMES PROPAGATION DELAY TIMES
vs VS
FREE-AIR TEMPERATURE INPUT RISE & FALL TIMES

12 13
1
VCC = 5 V
tr:: tf "" 5 ns
Vcc = 5 V
12 I- CL = 50 pF
V
. /V/V
CL = 50 pF RL=500n
? 10 ~
..
RL = 500n 1 11- TA = 25°C
tPL~~V
E V E
i= 9 i= 10
tPL~ V ~PHL
, ............
::.-..::: ---..---r-;p= f::=
~ 9
./v./
VV
V
/'
/'
2:
4
o
-~-W-H 0 H W ~ 100 1H 50 10 15 20 25 30 35 40 45
i=
T A-Free-Air Temperature- °c
FIGURE 1
Input Rise and Fall Times (10%-90%)-ns
FIGURE 2 «
2
'ALSOOA 'A LS244A a:
PROPAGATION DELAY TIMES
VS
VS
ou..
LOAD CAPACITANCE LOAD CAPACITANCE
90 90
2:
VCC = 5 V / VCC' 5 V
80 -t,= tf = 5 ns 80 I- tr = tf = 5 ns -I
RL=500n
70 -.TA=25°C
t P, /
/V RL=500n
70 I- TA = 25°C «
a:
T
~ 60 E 60 w
i=
/ . . . . .V i=
~ 50
2:
;; 50
"~ / ...V ~ ...........-

w
---- ---
Cl
.~ 40 C!'
40
V V't'PLH tPL~
1
30
V v,.-V" 1 30
,....------
,....-
-----
. - t~HL
., ?V
20 20
10 10
...-;::::. -;::::. f.-
Ir"'"
00 200 400 600 800 1000 1200 1400 1600 1800 2000 00 200 400 600 800 1 000 1200 1400 1600 1800 2000
Cl-Load Capacitance-pF CL-Load Capacitance-pF
FIGURE 3 'A LSOOA FIGURE 4
POWER DISSIPATION PER GATE
vs
FREQUENCY
~v~c~c=;S5:V"v-rTTTTTTTr--r:++rnim=r=mm
0
1
;: tr = tf = 5 ns
~ 7 CL' 0 pF
~ Clock Pulse = 0 V to 5 V I+1I-1+l+il----'ffH-It!l!l
(; All inputs switching
& 4~T~A4=~2m5moC-'Tnnw~~~+rH#~
."
.~
II
o
i 2~~~-++H~-r~~-rH*m
J:
I
~ /'
1-
- r-
----L..1..I.J.llJ.ll.---'-.J....LJ.J..WI...--'-LllJ.lllI
0.01 0.04 0.1 0.4 1 4 10 40 100
f-Frequency-MHz
FIGURE 5
tData for temperatures below OoC and above 70°C are applicable for Se~ies 54ALS circuits only.
TEXAS 1-13
INSTRUMENlS
SERIES 54AS/74AS
ADVANCED SCHOTTKY TRANSISTOR·TRANSISTOR LOGIC
TYPICAL CHARACTERISTICSt
'AS804A 'AS804A
PROPAGATION DELAY TIMES PROPAGATION DELAY TIMES
vs vs
FREE·AIR TEMPERATURE INPUT RISE AND FALL TIMES
r
VCC· S V
tr· tf· 2 ns
VC~·5~
8 - CL· 50 pF
v
t PH
CL· SOpF
/ RL"500n VI-'"
13 f-RL-SOOn
-L L - J.
TA - 25°C
/V
------
--
.~ f-tPl .~ 6
--
/
>
~ 2 o
-il S tpLH
c tPLH ,/
o
£
[ /-V
G') 1
f'
m
2 o 1
m -75 -50 -25 0 25 50 75
TA-Free·Air Temperature-°c
100 125 5 10 15 20 25 30 35 40 45
:xJ Input Rise and Fall Times-ns
:t>
r- FIGURE 1
(t,' tf 10% to 90%)
FIGURE 2
2 'AS804A
":xJo VS
LOAD CAPACITANCE
s:
:t>
VCC' S V
20 I-t,= tf" 2ns
t PH; ' - / '
::! RL=500n
I-TA·25'C
/"
o y 15
.~
//
tP~
2 > /'" L
0;
o // ./'
./'
.g 10
/"
/ /"
I I /"
V
&V
o
o 200 400 600 800 1000 1200 1400 1600 1800 2000
CL -Load Capacitance-pF
FIGURE 3
tData for temperatures below OOC and above 70°C are applicable for Series 54AS Circuits only.
1~
1.-14 TEXAS
INSTRUMENTS
FUNCTIONAL INDEX
GATES AND INVERTERS

POSITIVE·NAND GATES AND INVERTERS POSITIVE·AND GATES WITH OPEN·COLLECTOR OUTPUTS
TECHNOLOGY TECHNOLOGY
STD STD
DESCRIPTION TYPE ALS AS H L LS S VOLUME DESCRIPTION TYPE ALS AS H LS S VOLUME
TTL TTL
Hex 2-lnput Gates 'S04 A
Quadruple 2-lnput Gates '09
'04
Hex Inverters A
Triple 3-lnput Gates '15
····
'1004
..
'00
Quadruple 2·lnput Gates POSITIVE· OR GATES
····
'WOO
TECHNOLOGY
Tnple 3-lnput Gates '10 STD
DESCRIPTION TYP ALS AS LS S VOLUME
TTL
····
'1010 A
Hex 2-lnput Gates 'S32
'20
Dual 4-lnput Gates A Quadruple 2-lnput Gates '32 j........:~--I---1-=--+--=-4--=-~
····
'1020 A
'1032 A
a-Input Gates '30 Z
13-lnput Gates '133
Triple 4·lnpul ORINOR 'S02 ...
o
~
POSITIVE·NOR GATES
Dual 2-lnput Gates 'S003
STD
TECHNOLOGY
«
~
DESCRIPTION TYPE ALS AS L LS S VOLUME
POSITIVE· NAND GATES AND INVERTERS WITH OPEN· COLLECTOR OUTPUTS TTL
TECHNOLOGY
Hex 2-lnput Gates '805
a:
DESCRIPTION TYPE STD
TTL
ALS AS H L LS S VOLUME Quadruple 2-lnput Gates
'1002
'02
A
oL1.
'05 i--=-+--~I-+=-1--+-=-jL-:-I-~-i
Hex Inverters A Triple 3-lnput Gates '27 Z
'1005
Dual 4-lnput Gates with Strobe '25
..J
Quadruple 2-lnput Gates
'01 1-=+-::--I-+=++-=--Ji-I--7--1
'03 i--=-+---I-+--1--=-t--=-jL-:-I-~-i
A
Dual 5-lnput Gates '260
SCHMITT·TRIGGER POSITIVE·NAND GATES AND INVERTERS

«
a:
'1003 A w
1-=+--I-+-++-=--Ji-I-_=_--1
TECHNOLOGY
z
Triple 3-lnput Gates '12
DESCRIPTION TYPE
STD
TTL
ALS AS LS S VOLUME w
Dual 4-lnput Gates '22 i--=-+--A-+--+~I-+--=--1--+-:--j '14 • (!'
Hex Inverters
'19
Octal Inverters '619
POSITIVE·AND GATES
'13 •
Dual 4-lnput Positive-NAND
TECHNOLOGY 'IS
STD Triple 4-lnput Positive-NAND '618
DESCRIPTION TYPE ALS AS H LS S VOLUME
TTL '24
Quadruple 2-lnput Positive-NAND
Hex 2-lnput Gates 'SOS '132 •
'OS
Quadruple 2-lnput Gates CURRENT·SENSING GATES
'100S
'II DESCRIPTION
Triple 3-lnput Gates
'lOll Hex
Dual 4-lnput Gates '21

DELAY ELEMENTS
Triple 4·lnpul AND/NAND 'SOO
DESCRIPTION
Inverting & Non-Inverting Elements.

2·INPUT NAND Buffers
• Denotes available technology,

ADenotes planned new products,
A Denotes" A" suffix version available in the technology indicated,
33
TEXAS 1-15
INSTRUMENTS
FUNCTIONAL INDEX
GATES, EXPANDERS, BUFFERS, DRIVERS, AND TRANSCEIVERS

AND-DR-INVERT GATES GATES, BUFFERS, DRIVERS, AND BUS TRANSCEIVERS
TECHNOLOGY WITH 3-STATE OUTPUTS
.··
STD
DESCRIPTION TYPE ALS AS H L LS S VOLUME TECHNOLOGY
TTl
STD
2-Wide 4-lnput '55 DESCRIPTION TYPE ALS AS LS S VOLUME
TTL
4-Wide 4-2-3-2 Input '64
4-Wide 2-2-3-2 input '54 '241
•
. ·· ·· .
4-Wide 2-lnput '54
4-Wide 2-3-3-2 input '54 '244
Dual 2-Wide 2-lnput '51
'465
Non-Inverting
AND-OR-INVERT GATES WITH OPEN-COLLECTOR OUTPUTS
Octal BufferslDrivers
'467
~ ~D_E_SC_R_IP_TI_ON________________~__~~~-+__~~__~ '541
_ _ 4-Wide 4-2-3-2-lnput '124H

'1244\
EXPANDABLE GATES '231
G')
m TECHNOLOGY '240
Z DESCRIPTION TYPE
STD
ALS AS H L LS VOLUME
m Dual 4-lnput Positive-NOR
TTL
Inverting Octal
'466
:xl '23 Buffers/Drivers
»
With Strobe '468
4-Wide AND-OR '52
r- 4-Wide AND-OR-INVERT '53 '540
2-Wide AND-DR-INVERT
Dual 2-Wide AND-DR-INVERT
'55
'50
'1240\ "
Z Inverting and Non-Inverting
'230
"T1 Octal Buffers/Drivers
o EXPANDERS
TECHNOLOGY Octal Transceivers

'245
" ,3
:xl DESCRIPTION TYPE
STD
ALS AS H VOLUME
'1245
~ TTl
'365
» Dual 4-lnput
Triple 3-lnput
'60
'61
Non-inverting
Hex Buffers/Drivers
'367
::! 3-2-2-3-lnput AND-OR '62
"
o BUFFER AND INTERFACE GATES WITH OPEN-COLLECTOR OUTPUTS Inverting
'366
"
z TECHNOLOGY
Hex Buffers/Drivers
'368
DESCRIPTION
TYPE
STD
ALS AS LS S VOLUME '125 " A
·· "
TTL Quad Buffers/Drivers
'126
'07 with Independent
'425
Output Controls
'17 '426
Hex
'35
Non-Inverting '243
'1035
··
A
Quad Transceivers
'06 '1243\
Hex Inverter '16
'242
"
·
'1005 Inverting
'26 Quad Transceivers

'1242\
'38 Quad Transceivers with Storage '226 "
·
Quad 2-lnput Positive-NAND
12-lnput NAND Gate '134
'39
Controller and Sus Driver
'1003 A '42B
for S080A System
Quad 2-lnput Positive-NOR '33
A
50-0HMf75-0HM LINE DRIVERS
BUFFERS, DRIVERS, AND BUS TRANSCEIVERS WITH OPEN-COLLECTOR OUTPUTS TECHNOLOGY
DESCRIPTION TYPE STD ALS AS S VOLUME

TECHNOLOGY TTl
STO Hex 2-lnput Positive-NAND 'S04
DESCRIPTION TYPE ALS AS LS S VOLUME
TTL
Hex 2-lnput Positive-NOR '805 A
Non-inverting '757
Octal Buffers/Drivers '760 " Hex 2-lnput Positive-AND '80S A
Inverting Octal '756 " Hex 2-lnput Positive-OR 'S32
Buffers/Drivers '763 " Quad 2-lnput Positive-NOR '12S
Inverting and Non-Inverting

'762
" Dual 4-lnput Positive-NAND '140
Octal Buffers/Drivers
Non-Inverting Quad Transceivers '759 -Denotes available tchnology,
Inverting Quad Transcoivers '758 ADenotes planned new products_
, Denotes very low power_
A Denotes" A" suffix version available in the technology indicated_
1-16 TEXAS
INSTRUMENTS
FUNCTIONAL INDEX
BUFFERS, DRIVERS, TRANSCEIVERS, AND CLOCK GENERATORS
BUFFERS, CLOCK/MEMORY DRIVERS OCTAL BI-/TRI-DIRECTIONAL BUS TRANSCEIVERS
TECHNOLOGY TYPE TECHNOLOGY

STD OF
DESCRIPTION TYPE ALS AS H LS S VOLUME DESCRIPTION TYPE ALS AS VOLUME
TTL OUTPUT
Hex 2-lnput Positive-NAND '804 A
3-518t8 '245
Hex 2-lnput Positive-NOR '80S A
Hex 2-lnput Positive-AND '808 A
oc -621
..
Hex 2-lnput Positive-OR '832 A 3
Hex Inverter '1004
3-$tete '623
..
'34 A
Hex Buffer 12 mA/24 mA/4S mA/64 mA
'1034
Sink. True Outputs Ce,3-$t8te '639
'37
Quad 2-lnput Positive-NAND A
3-Stete '652
'1000 A
'28 DC,3-$tate '654

A
Quad 2-lnput Positive-NOR
'1002 A OC Z
Quad 2-lnput Positive-AND
'1036
'1008
Very low
3-State
aC.3-Stat8
'1623
'1639
... o
Quad 2-lnput Positive-OR '1032
3-5tat8 '620 i=
Triple 3-lnput Positive-NAND
Triple 3-lnput Positive-AND
'1010
'lOll A
<C
Triple 4-lnput AND-NAND '800 A
OC -622
:E
Triple 4-lnput OR-NOR '802 A 12 mA/24 mA/4S rnA/54 rnA
aC,3-State '638 a::
Dual 4-lnput Positive-NAND
'40
'1020 A
Sink. Inverting Outputs
3-$tate
ou..
Line Driver/Memory Driver
'436 aC,3-State '653 Z
with Series Damping Resistor
line Driver/Memory Driver '437
Very Low
3-$tate '1620
-I
OC '1622
Power
DC,3-State '1638 <C
BI-/TRI-DIRECTIONAL BUS TRANSCEIVERS AND DRIVERS
a::
TYPE TECHNOLOGY
OC '641
w
DESCRIPTION
OF
TYPE ALS AS LS S VOLUME
12 mA/24 mA/4S rnA/S4 rnA Power
3-$t8te '645 Z
Quad with Bit Direction
OUTPUT
3-State '446
Sink. True Outputs,
Very Low OC '1641
w
Controls 3-State '449 3-$tate '1645 t!'
OC '440
3-5t8te -640
OC '441
3-State '442 12 mA/24 mA/4S rnA/S4 rnA Power
Quad Tridirection
3-State '443 Sink. Inverting Outputs
3-State '444 VervLow 3-St8te '1640
OC '448 Power OC '1642
4-Bit with Storage 3-State '226
3-$tate '643
Controller and Bus Driver for 80aOA Systems '428
12 mA/24 mA/4S rnA/64 rnA
Power
Sink. True and OC '644
Inllerting Outputs
OCTAL BUS TRANSCEIVERS/MOS DRIVERS Very Low 3-St8te '1643
TECHNOLOGY
STD Registered with Multiplex 3-$tate '646
DESCRIPTION TYPE ALS AS LS S VOLUME
TTL 12 mA/24 mA/4S rnA/S4 mA
Inverting Outputs, 3-State
True Outputs, 3-State

'2620
'2640
'2623
'2645
A
A
A
A
True Outputs
Registered with MUltiplexed

12 mA/24 mAl4S rnA/64 rnA
OC
3·5t8te
'647
'648
... .
Inverting Outputs OC -649
Universal Transceiverl
3-5tate '852
Port Controllers
'856

... Denotes planned new products,
83
TEXAS 1-17
INSTRUMENlS
FUNCTIONAL INDEX
FLIP-FLOPS
DUAL AND SINGLE FLIP-FLOPS OUAD AND HEX FLIP-FLOPS
STD NO. OF STD
DESCRIPTION TYPE ALS AS H L LS S VOLUME DESCRIPTION OUTPUTS TYPE ALS AS LS S VOLUME
TTL FFs TTL
'73
'174
'76 Q
'78 '378
'103 o Type '171
'106
..
Q, Q '175
'107
Dual J-K Edge-Triggered '108 '379
'276
'109 J-K
·
'376
A
'112
...
·
A OCTAL, 9-BIT, AND 10-BIT D-TYPE FLIP-FLOPS
A
'113
... TECHNOLOGY
·
A
NO. OF STD
G) A DESCRIPTION OUTPUT TYPE ALS AS LS S VOLUME
'114
... BITS TTL
m '70 3-State '374
:2: Single J-K Edge-Triggered '101
True Data Octal
m '102
3-State '574
:c '73 2-State '273
»
.r
Dual Pulse-Triggered
'76
'78
'107
True Data with Clear Octal 3-State
3-5tate
'575
'874
3-State '878
'71
:2: Single Pulse-Triggered
'72
True with Enable Octal 2-5tate
3-5tate
'377
'534
"T1 '104
Inverting Octal 3-5tate '564
0 Dual J-K with Data
'105
3-State '576
:c Lockout
'111
Inverting with Clear Octal
3-State '577
S 3-State '879
.. ·
Single J-K with Data
»
'110 Inverting with Preset Octal 3-State '876
lockout
A
True Octal 3-State '825 ...
...
::! DualD-Type '74 Inverting
True
Octal
9-8it
3-State
3-State
'826
'823 ...
0 Inverting 9-Bit 3-5tate '824 ...
:2: True
Inverting
10-Bit
10-Bit
3-State
3-State
'821
'822
• Denotes available tchnology_

"'Denotes planned new products_
12
1-18 TEXAS
INSTRUMENlS
FUNCTIONAL INDEX
LATCHES AND MULTIVIBRATORS

QUAD LATCHES OCTAL, 9-BIT, AND 10-BIT LATCHES
STD NO. OF STD
DESCRIPTION OUTPUT TYPE ALS AS L LS VOLUME DESCRIPTION OUTPUT TYPE ALS AS LS S VOLUME
TTL BITS TTL
2-State '75
Dual2·Bit '268
2-5tate '77
Transparent 3-5tate
2-State '375 Transparent Octal '373
S-R 2-5tate '279
3-5tate ·573
2-5tate '100
RETRIGGERABLE MONOSTABLE MULTIVIBRATORS Dual4-Bit
Octal 2-5tate '116
Transparent
TECHNOLOGY 3-5tate '873
STD 3-5tate '533
DESCRIPTION TYPE ALS AS LS L VOLUME
TTL Inverting Transparent Octal 3-State '563
Single
Dual
'122
'130
'422
'123
'423
Dual4-Bit
Inverting Transparent
Octal
3-5tate
3-5tate
3-5tate
'580
'880
'604
'605
mI2:
2-lnput Multiplexed Octal
OC
3-5tate
OC
'606
'607
o
Addressable Octal 2-State
3-State
'259
'412
... ~
Multi·Mode Buffered
True
Octal
Octal 3-State '845 ... ... 2
Inverting Octal 3-5tate '846 ... ... a::
True
Inverting
9-8it
9-Bit
3-5tate
3-5tate
'843
'844
...
...
...
... o
LL
True 10-Bit 3-State '841 ... ...
Inverting 10-Bit 3-State '842 ... ... 2:
MONOSTABLE MULTIVIBRATORS WITH SCHMITT-TRIGGER INPUTS
-'
TECHNOLOGY <t
~~~ I ALSI Asi LS
I
a::
DESCRIPTION TYPE
Is
VOLUME
w
Single '121 • I I I I 2 2:
Dual '221 • I I I• I w
~
• Denotes available technology.

"'Denotes planned new products.
A Denotes" A" suffix version available in the technology indicated,
283
TEXAS 1-19
INSTRUMENlS
FUNCTIONAL INDEX
REGISTERS AND PROGRAMMABLE LOGIC ARRAYS
SHIFT REGISTERS REGISTER FILES
TECHNOLOGY
NO, I-~~CO TECHNOLOGY
DESCRIPTION OF a:..Joc( -' TYPE STD STD VOLUME
ALS AS L LS S VOLUME DESCRIPTION OUTPUT TYPE ALS AS LS
BITS V,cn9~ TTL TTL
Sign-Protected '322 8 Words x 2 Bits 3·5,.,. '172
x X '198 OC '170
4 Words x 4 Bits
Perallel-In. 3-5tate '670
Parallel·Out.
Bidirectional
Du.1 16 Words x 4 Bils
3·5,.,.
3·5,.,.
'870
'871
••
x X X X '323
OTHER REGISTERS
X X '194
TECHNOLOGY
Parallel-In.
X X '571 STD LS S VOLUME
Parallel-Out. DESCRIPTION TYPE ALS AS L
TTL
Registered
'572 '98
Outputs Quadruple Multiplexers
'298
G) '199 with Storage
'391l/9
m '96
a·Bit Universal Shift
'299
2 '95 Registers
•
m Parallel-In,
Quadruple Bus-Buffer
Registers
'173 A
:lJ
»
Parallel-Out '178
Octal Storage Register '396
'179
r- '195 PROGRAMMABLE LOGIC ARRAYS
'295 OUTPUTS TYPE NO, OF

2 '395
DESCRIPTION INPUTS
NO, TYPE NO PINS
VOLUME
":lJo Serial-In
Parallel-Out
'673
'164
16 ~
6
r--;-
Active-Low
Registered
~
~
'PAL16l8
'PA1I5R6
20
S '674 'PlR19l8
»
:j
Parallel-In. 19 Registered 2-
-;-
6 Registered ~
'PlA19RB
24
~
Serial-Out
1---+--+--+-+-+-+---1
o '166 Fixed-OR Arrays
Active-low 'PlT19l8
2
Serral-In,
Serral-Out '94
19 latched
+
2-
ReQlstered
~
'PLT19A8
'PLT19R4
2'
SHIFT REGISTERS WITH LATCHES Active-low 'PL20L8
NO,
I 'Pl20R8
TECHNOLOGY 20 24.
Registered I 'Pl20R6
DESCRIPTION OF OUTPUTS TYPE VOLUME
ALS AS LS 'Pl2QA4
BITS
Field-Programmable 3-St8te 'Pl839
Parallel-In, Parallel-Out 3-State '671 24
14 x 32 x 6 logic Arrays oc 'PL840
with Output latches 3·5,.,. '672
16 2·5,.,. '673
Serial-In. Parallel-Out Buffered '594
with Output latches 3·5,.,. '595
OC '596
OC '599
Parallel·ln, Serial-Out. 2·5,.,. '597
with Input Latches 3·5,.,. '589
Parallel 110 Ports with
Input Latches. Multiplexed 3-State '598
Serial Inputs
SIGN·PROTECTEO REGISTERS
DESCRIPTION
Sign-Protected Register

"'Denotes planned new products,
A Denotes" A" suffix version available in the technology indicated.
S Denotes "S" suffix version available in the technology indicated.
12B~
1-20 TEXAS
INSTRUMENTS
FUNCTIONAL INDEX
COUNTERS
SYNCHRONOUS COUNTERS - POSITIVE-EDGE TRIGGERED ASYNCHRONOUS COUNTERS (RIPPLE CLOCK) - NEGATIVE·EDGE TRIGGERED
TECHNOLOGY
PARALLEL t-T"'Y:::P=-Er:S""'TO=D-r-T:..::E.::.cCH,.:.N:..::O.::.,LO;:.:G:":'Y.--.--i PARALLEL
DESCRIPTION DESCRIPTION TYPE STD VOLUME
LOAD TTL ALS AS L LS S VOLUME LOAD ALS AS L LS S
TTL
Set-to-9 '90
Sync "60
•
·
A '68
A Decade Yes "76
Sync "62
Decade
Sync '560
A
A
• Yes
Set·to-9
"96
'290
Sync '668 None '93
Sync '690 '69
·
Sync '692 4·Bit Binary Yes "77
B Yes "97
Sync "68
• None '293
Decade Up/Down
Async
Async
"90
"92
Divide-by-12
Dual Decade
Dual 4-Bit Binary

None
None
Set-to-9
None
'92
'390
'490
'393
DI
z
Sync
Sync
'568
'696
A
8·BIT BINARY COUNTERS WITH REGISTERS o
,
~
Sync '698
TYPE TECHNOLOGY
Decade Rate Async
"67 DESCRIPTION OF TYPE VOLUME
Multipier, N'O Set-to-9 ALS AS LS
OUTPUT
Sync Parallel Register 3·State '590 2
"6'
a:
4·Bit Binary
Sync
Sync
"63
'56' A
•
A
· Outputs
Parallel Register Inputs
ParaliellfO
OC
2-S1ale
3-State
'59'
'592
'593
o
LL
Sync
Sync
'669
'69'
FREQUENCY DIVIDERS, RATE MULTIPLIERS Z
·
Sync '693 TECHNOLOGY
DESCRIPTION TYPE STD VOLUME
..J
B
Sync "69
• TTL
ALS AS LS
<C
50-to-l Frequency Divider '56 a:
Async "9' 60-to- 1 Frequency Divider '57 w
4·Bit Binary
Up/Down Async "93
60-Bit Binarv Rate Multiplier. '97
z
Sync '569
Decade Rate Multiplier. "67
w
Sync '697 e"
6·Bit Binary , Sync '699
'97
Rate Multipler. N2
Async CLR '867
8-Bit Up/Down
Sync CLR '869

ADenotes planned new products.
8 Denotes "8" suffix version available in the technology indicated.
283
TEXAS 1-21
INSTRUMENTS
FUNCTIONAL INDEX
DECODERS, ENCODERS, DATA SELECTORS/MULTIPLEXERS AND SHIFTERS

DATA SELECTORS/MULTIPLEXERS DECODERS/DEMULTIPLEXERS
TYPE TECHNOLOGY TYPE TECHNOLOGY
.
DESCRIPTION OF TYPE STD VOLUME DESCRIPTION OF TYPE STD VOLUME
ALS AS L LS S ALS AS L LS S
OUTPUT
··
TTL OUTPUT TTL
2-State '150 3-State '154
4-To-16
16 -To-l
3-State '250
• OC '159
•
.
3-State '850 4- T0-10 8CO-To-Oec;mal 2-State '42 A
DuaI8·To-'
3-State
3-State
'851
'351
• 4-To-10 Excess 3-To-
2-State '43 A
..
Decimal
4- To-l 0 Excess 3-Gray-
2-State '151 2-State '44 A
To-Decimal
2-State '152 A
3- To-8 with Address
'131
•
8-To-l
3-State '251
• Latches 2-State '137 •
3-5tat8
2-5tate
'354
'355 3-To-8
2-State '138 •
•
..·
3-State '356
.
3-State '538
G') OC '357
2-State '139 •
m
··
A
2-State '153 Dual 2-To-4
2-State '155 A
:2 OC '156
m DuaI4-To-l
3-State '253
Dual 1-To-4 Decoders 3-State '539
•
:xl
»
r-
2-State
3-State
'352
'353
CODE CONVERTERS
TECHNOLOGY
:2 Octal 2-lo-' with Storage
3-State
OC
'604
'605
6-Line-BCD to 6-Line Binary, Or 4-Line to 4-Une
TTL
"
3-5tate '606 '184
BCD 9's/BCD 10's Converters
0- OC
2-5tate
'607
'98
6-Bit-Binary to 6-Bit BCD Converters '185
:xl BCD-ta-Binary Converters '484 A
s: Quad 2-To-' with Storage

2-5tate '298
• Binary-to-BCD Converters '485 A
» /
2-5tate
2·5tate
'398
'399
..· PRIORITY ENCODERS/REGISTERS
::! 2-State '157 TECHNOLOGY
0 DESCRIPTION TYPE STD

TTL
ALS AS LS
VOLUME
:2 2-State '158
·
Ful18CO '147
Quad 2-To-l
8 Cascadable Octal '148
3-5tate '257
·
Cascadable Octal with 3-5tate Outputs '348
8 4·8it Cascadable with Registers '278
3-5tate '258
6-to-1 UnIversal SHIFTERS

3-State '857
Multiplexer
TECHNOLOGY
DESCRIPTION OUTPUT TYPE STD VOLUME
ALS AS L LS S
TTL
4-8;t Shifter 3-State '350
Parallel 16·8;t
Multi-Mode
Barrel Shifter
3-State '897
•

ADenotes planned new products,
B Denotes "B" suffix version available in the technology indicated.
128
1-22 TEXAS
INSTRUMENTS
FUNCTIONAL INDEX
DISPLAY DECODERS/DRIVERS, MEMORY/MICROPROCESSOR CONTROLLERS,

AND VOLTAGE-CONTROLLED OSCILLATORS
OPEN· COLLECTOR DISPLAV DECODERS /DRIVERS MEMORY /MICROPROCESSOR CONTROLLERS
DFF·STATE TECHNOLOGV TECHNOLOGV

DESCRIPTION TYPE ALS AS lS S VOLUME
DESCRIPTION OUTPUT TVPE STD VOLUME
ALS AS L LS
VOLTAGE TTL System Controllers For 8080A '428
30 V '45 System Controller, Universal '482
60 V '141 System Controllers. Universal '890
BCD-lo-Decimal
15 V '145 lor For '888, '8891 '891
..
7V '445 LI-4,;:,K::..,'..;.:16:.:;K~--:'6::-:0:-:.0-t_+--t-':'-t---i
30 V.
15 V
'46
'47
~e~::~y I Transparen1,
Burst Modes
Cycle Steal,
I 64K
L4K, 16K
'601
'602
5.5 V
5.5 V
'48
'49
Controllers
I Burst Modes
Memory Cycle Controller

16';:'4::"'K":"::':;~--:'::-:60:-:'3-t-·+--t-':'-t---i
I-
'608
30 V '246 , 3·State '612
BCD-Ta-Seven-Segment Memory Mappers
15 V '247 loc '613
7 V '347 Memory Mappers I 3·Sta1e '610
7V '447 With Output Latches loc '611
Z
5.5 V
5.5 V
'248
'249
Multi-Mode Latches (B080A Applications)
CLOCK GENERATOR CIRCUITS

'412
o
~
OPEN COLLECTOR DISPLAY DECODERS/DRIVERS WITH COUNTERS/LATCH
TECHNOLOGV
TECHNOLOGV DESCRIPTION TVPE STD VOLUME
DESCRIPTION TVPE STD ALS AS VOLUME TTl
ALS AS lS S
2
TTl Quadruple Complementary-Output
'265 a:
BCD Counter/4-Bit Latch/BCD-Ta-Decimal
Decoder/Driver
BCD Counter/4-Bit
'142
Logic Elements
Dual Pulse Synchronizers/Drivers '120
'320
oLL
Crystal-Controlled Oscillators
Latch/BCO-To-Seven-Segment
Decoder/Lad Driver
'143
Digital Phase-Lock Loop
'321
'297
Z
BCD CounterJ4-Bit Programmable Frequency '292
Latch/BCD-To-Seven-Segment Dividers/Digital Timers '294
....I
Decoder/Lamp Driver
'144
Triple 4-lnput AND/NAND Drivers '800 A <C
Triple 4-lnput OR/NOR Drivers '802 A a:
VOL TAGE·CDNTROLLED OSCILLATORS Dual VCO '124 w
DESCRIPTION TECHNOLDGV zw
TVPE VOLUME
No. CDMP'L
ENABLE
RANGE
Rext
f max
LS (!)
VCD'S lOUT INPUT MHz
Single Ves Ves Ves No 20 '624
Single Ves Ves Ves Ves 20 '628
Dual No Ves Ves No 60 '124
Dual Ves Ves No No 20 '626
Dual No No No No 20 '627
Dual No Ves Ves No 20 '629
RESULTANT DISPLAYS USING '46A, '47A, '48, '49, 'L46, 'L47, 'LS47, 'LS48, 'LS49, 'LS347
o 2 3 4 5 6 7 8 9 10 11 12 13 14
RESULTANT DISPLAYS USING '246, '247, '248, '249, 'LS247, 'LS248, 'LS249, 'LS447
o 2 3 4 5 6 7 8 9 10 11 12 13 14
RESULTANT DISPLAYS USING '143, '144
li:1 1-1,'1-_-111'--1'1- ,1-11--11- 11_1-

1 iii_III-III
1
o 2 3 4 5 6 7 8 9

"Denotes planned new products.
183
TEXAS 1-23
INSTRUMENTS
FUNCTIONAL INDEX
ARITHMETIC CIRCUITS, ERROR DETECTION CIRCUITS, AND PROCESSOR ELEMENTS

4·BIT COMPARATORS PARALLEL BINARY ADDERS
TECHNOLOGY
ALS AS H LS S
TTL
l·Bit Gated '80
2·Bit '82
a·BIT COMPARATORS '83 A
4·Bit
'283
DESCRIPTION
Dual 1-Bit Carry-Save '183
VOLUME
INPUTS P:O p:a P>O P>O OUTPUT ALS AS LS
ENABLE
ACCUMULATORS, ARITHMETIC LOGIC UNITS,
LOOK·AHEAD CARRY GENERATORS
20-kU
No OC '522 TECHNOLOGY
Pull-Up
_ _ No Yes No 2-$tate '682 DESCRIPTION TYPE STD VOLUME
ALS AS LS S
~____~-+_N~04-__~_NO-+__
0_C-4____~~'6_8-43__4-~-4__~ TTL
No OC '519 '281
4-Bit Parallel Binary Accumulators
'681
G) No
'181 I---=~--+---t-.-=--+-=.-+---~
m No '685
4-Bit Arithmetic Logic Unitsl
2 Standard
No 2·State '686
Function Generators' '381 1--+--+-+~-1
m OC '687
'881
lJ
»
r- OC '689
4-Bit Arithmetic Logic Unit
with Ripple Carry
'382
~
Look-Ahead Carry 16-Blt
'182 I---=~-+-+-+~f-...!:...----l
...
No Yes 2·$tate '885
2 Generators
J
1-::-::-=----------1I-'-=-=28:-::2-t---t---+.;::.-t--t---t---::--i
32·Bit '882
'TI Yes latched '866
o P and Q Quad Serial Adder/Subtractor

4-Bit Slice Elements
'385
'481
lJ AODRESS COMPARATORS
8-Bit Slice Elements
'888
'889
S DESCRIPTION
OUTPUT LATCHED
TYPE
TECHNOLOGY
VOLUME
» l6-Bit to 4-Bit
ENABLE
Yes
OUTPUT
'677
ALS AS
MULTIPLIERS
:::! Yes
'678 .' TECHNOLOGY
o 12-8it to 4-Bit
Yes
Yes
'679
'680'.
DESCRIPTION TYPE STD
TTL
ALS AS LS S VOLUME
2 PARITY GENERATORS/CHECKERS,
2-Bit-by-4-8it Parallel Binery Multipliers '261
'274
ERROR DETECTION AND CORRECTION CIRCUITS 4-Brt-by-4-Bit Parallel Binary Multipliers '284 •
'285 •
NO. TECHNOLOGY
25-MHz 6-Blt Binary Rate Multipliers '97 •
DESCRIPTION OF TYPE STD VOLUME
ALS AS
..
LS S 25-MHz Decade Rate Multipliers '167 •
BITS TTL
B-Bit x 1-Bit 2's Complement Multipliers '384
'180
16-Bit Parallel Multiplier '1616 •
Odd/Even Parity
'280 f--+--+-,.+-t--t---;:--j
Generators/Checkers
OTHER ARITHMETIC OPERATORS
'286
3-State '636 TECHNOLOGY
OC '637 DESCRIPTION TYPE STD VOLUME
ALS AS H L LS S
3·State 16 '630 TTL
Parallel Error
OC 16 '631 Quad 2-lnput Exclusive-OR • A •
Detection/CorrectIon '86 I---'-+-.-:---t---t--t--+-+-t--':-----l
3·State 32 '632 Gates with Totem-Pole
Circuits
OC 32 '633 Outputs '386 A
3·State 32 '634 Quad 2-lnput Exclusive-OR
OC 32 '635 Gates with Open-Collector '136
Outputs
FUSE· PROGRAMMABLE COMPARATORS Quad 2-lnput Exclusive-
'266
NOR Gates
TECHNOLOGY
Quad Exclusive OR/NOR
DESCRIPTION TYPE STD VOLUME '135
ALS AS LS S Gates
TTL
4-Bit True/Complement,
16-Bit Identity Comparator '526 '87
Element
12-8it identity Comparator '528
8·Bit Identity Comparator
'527 BIPOLAR BIT·SlICE PROCESSOR elEMENTS
and 4-Bit Comparator
CASCADABLE TECHNOLOGY
DESCRIPTION TO TYPE VOLUME
ALS AS LS S
N·BITS
4-Bit-Slice Yes '481
• Denotes available tchnology.
Yes '888
ADenotes planned new products. 8-Bit-Slice
Yes '889
A Denotes "A" suffix version available in the technology .indicated,
121
1-24 TEXAS
INSTRUMENlS
FUNCTIONAL INDEX
MEMORIES
USER-PROGRAMMABLE READ-ONLY MEMORIES IPROM'.I
STANDARD PROM'. READ-ONLY MEMORIES IROM'sl
TYPE TYPE TECHNOLOGY

DESCRIPTION TYPE ORGANIZATION VOLUME
~~IALSIASls
OUTPUT DESCRIPTION ORGANIZATION OF TYPE VOLUME
~ TBP28S165 2048W x 8B 3-Stst. OUTPUT
16K·Bit Arrays
TBP285166 2048W x 8B 3-Stst. 1024-8it Arrays 256 x 4 OC '187 • I I I 4
TBP24S81 2048W x 4B 3-5tst. 256-6it Arrays 32 x 8 OC '88 A I I T
TBP24SABI 204BW x 4B OC
SK·Bit Arrays TBP28SB6A 1024W x 8B 3-Stst.
TBP285AB6A 1024W x 8B OC RANDOM-ACCESS READ-WRITE MEMORIES IRAM'sl
-
~ TBP28585A 1024W x BB 3-Stst.
TBP28542 512W x 8B 3-Stst. TYPE TECHNOLOGY
TBP285A42 512W x 8B OC DESCRIPTION ORGANIZATION OF TYPE STD VOLUME
AlS AS lS S
~ TBP28545 512W x BB 3-Stst. OUTPUT
4K-Blt Arravs TBP28546 512W x 8B 3-Stst. 3-$tate '2Q'
256-Bit Arrays
TBP28SA46 512W x 8B OC OC
TBP24541 1024W x 4B 3-Stst. OC '89 2:
TBP24SA41
TBP24510
1024W x 4B'
256W x 4B
OC
3-Stst. G4·Bit Arrays 16 x 4
3·$tate
3·State '2'9
A B
o
~
lK-Blt Arrays
TBP24SA10 256W x 4B OC OC '289 A B
TBP185030 32W x 8B 3-Stat. OC '3'9
256-Bit Arrays
TBP18SA030 32W x 8B OC lG-Bit Multiple-Port
~
8 x 2 3-State "72
Register File
16-Bit Register File

OC '170
a:
LOW-POWER PROM',
TYPE
Dual G4-Bit
Register Files
16 x 4
3-State
3·State
'670
'870
'87'
oLL
DESCRIPTION TYPE ORGANIZATION VOLUME
~ TBP28L 165 2048W x 8B

OUTPUT
3-Stst. FIRST-IN FIRST-OUT MEMORIES IFIFO'SI
2:
16K·Bit Arrays
~ TBP28L166 2048W x 8B 3-State
-I
«
TYPE TECHNOLOGY
~ TBP28L85A 1024W x 8B 3-Stst.
8K-Blt Arrsys DESCRIPTION TYPE VOLUME
TBP28L86A 1024W x 8B 3-Stat.
TBP2BL42 512W x 8B 3·State
OUTPUT
AlS AS lS lS
a:
4K-Bit Arrays ~ TBP28L45 512W x 8B 3-Stst.
Asynchronous 1 6 x 5 3-State
3-State
'225
'222
w
T8P28L46 512W x 8B 3-Stat.
3·St8te '22_ 2:
2K-Bit Arrays
TBP28L22
TBP28LA22
256W x 8B
256W x 8B
3-State
OC
Asynchronous 16 x 4
DC -227 w
OC (!)

... Denotes planned new products,
83
TEXAS 1-25
INSTRUMENTS
1m
G')
m
2!
m
:tI
»
r-
2!
":tIo
s:»
:::!
o
2!
1-26 TEXAS
INSTRUMENTS
The TTL Data Book
Volume 3
I~----·--_·---·-----·------------·.:...-.
_General Information _,
~1_A_L_S_a_n_d__
A_S_C_i_rC_u_it_s____________~_RII
, rMechanicat'Da~a'"
2-1
2-2
TYPES SN54ALSOOA, SN54ASOO, SN74ALSOOA, SN74ASOO
QUADRUPLE 2·INPUT POSITlVE·NAND GATES
02661. APRIL 19B2-REVISED DECEMBER 19B3
• Package Options Include Both Plastic and

Ceramic Chip Carriers in Addition to Plastic
and Ceramic DIPs
• Dependable Texas Instruments Quality
and Reliability
description SN54ALSOOA. SN54ASOO ••• J PACKAGE
SN74ALSOOA. SN74ASOO ••• N PACKAGE
These devices contain four independent 2-input (TOP VIEW)
NAND gates. They perform the Boolean functions
Y = A'B orY = A+Bin positive logic. 1A
1B
The SN54AlSOOA and SN54ASOO are character- 1Y
ized for operation over the full military temperature
range of - 55°C to 125°C. The SN74AlSOOA and 28 38
SN74ASOO are characterized for operation from OOC 2Y 3A
to 70°C.
-....._ _...r- 3Y
FUNCTION TABLE (each gate)
INPUTS OUTPUT
A B y SN54ALSOOA. SN54ASOO ••• FH PACKAGE
..
H H L SN74ALSOOA. SN74ASOO ••• FN PACKAGE
L X H (TOP VIEW)
X L H U
co<{UUco
........ z>-t
logic symbol
4A
NC CJ)
4Y !::
NC ::J
3B (.)
a:
(.)
CJ)
NC-No internal connection <t
Pin numbers shown are for J and N packages.
c
2:
<t
CJ)
...I
<t
Copyright © 1982 by Texas Instruments Incorporated

2
TEXAS 2-3
INSTRUMENTS
TYPES SN54ALSOOA, SN74ALSOOA
QUADRUPLE 2·INPUT POSITIVE·NAND GATES
absolute maximum ratings over operating free·air temperature range (unless otherwise noted)
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALSOOA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALSOOA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00eto700e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 °e
recommended operating conditions

SN54AlSOOA SN74AlSOOA
UNIT
MIN NOM MAX MIN NOM MAX
Vee Supply voltage 4.5 5 5.5 4.5 5 5.5 V
VIH High-level input voltage 2 2 V
Vil low-level input voltage 0.8 0.8 V
IOH High-level output current -0.4 -0.4 mA
IOl low·level output current 4 8 mA
TA Operating free-air temperature -55 125 0 70 °e
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54AlSOOA SN74AlSOOA
PARAMETER TEST CONDITIONS UNIT
MIN TYPt MAX MIN TYPt MAX
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V. IOl = 4 mA 0.25 0.4 0.25 0.4
VOL V
16 II
IIH
Vee
Vee
Vee
= 4.5 V.
= 5.5 V.
= 5.5 V.
IOl = 8 mA
VI = 7 V
VI = 2.7V
0.1
20
0.35 0.5
0.1
20
mA
»
r-
III Vee = 5.5 V. VI = 0.4 V -0.1 -0.1
/AA
mA
en lo~
leeH
Vee
Vee
= 5.5 V.
= 5.5 V.
Vo = 2.25 V
VI = 0 V
-15
0.5
-70
0.85
-15
0.5
-70
0.85
mA
mA
»
:2
leel Vee = 5.5 V,
tAli typical values ara at Vee = 5 v, TA = 25°e.
VI = 4.5 V 1.5 3 1.5 3 mA
C *The ~utPut conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
»
en switching characteristics (see Note 1)
Vcc - 4.5 V to 5.5 V,
~ Cl = 50 pF,
:lJ FROM TO Rl = 500 Q.
o PARAMETER
(INPUT) (OUTPUT) TA = MIN to MAX
UNIT
c SN54AlSOOA SN74AlSOOA
=t
en MIN MAX MIN MAX
tplH A or 8 Y 3 14 3 11 ns
tpHl A or B Y 2 10 2 8 ns
NOTE 1: For load CirCUit and voltage waveforms, see page 1·12.
12
2-4 TEXAS
INSTRUMENTS
TYPES SN54ASOO, SN74ASOO
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ASOO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ASOO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00eto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '........ - 65°C to 1 50°C

SN54ASOO SN74ASOO
UNIT
VCC Supply voltage 4.5 5 5.5 4.5 5 5.5 V
VIL Low-level input voltage 0.8 0.8 V
10H High-level output current -2 -2 mA
10L Low-level output current 20 20 mA
SN54ASOO SN74ASOO
VIK Vee = 4.5 V, II'" -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V. 10H = -2 mA Vee- 2 Vee- 2 V
VOL Vee = 4'.5 V. 10L = 20 mA 0.35 0.5 0.35 0.5 V
II
IIH
IlL
Vee
Vee
Vee
= 5.5 V.
= 5.5 V.
= 5.5 V.
VI = 7 V
VI = 2.7V
VI = 0.4 V
0.1
20
-0.5
0.1
20
-0.5
mA
Il A
mA
tJIIIII
en
10* Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
IceH Vce = 5.5 V. VI = OV 2 3.2 2 3.2 mA
!:::
IceL Vee = 5.5 V. VI = 4.5 V 10.8 17.4 10.8 17.4 mA
:l
tAli typical values are atVCC -- 5V.TA = 25 0 C.
U
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' a:
U
switching characteristics (see Note 1)
en
Vcc = 4.5 V to 5.5 V. «
FROM TO
CL = 50 pF.
RL = 500 Q.
c
PARAMETER UNIT 2
(INPUT) (OUTPUT)
SN54ASOO
TA = MIN to MAX
SN74ASOO
«
MIN MAX MIN MAX en
..J
tpLH
tPHL
A or B
A or B
Y
Y
1
1
5
5
1
1
4.5
4
ns
ns
«
NOTE 1: For load Circuit and voltage waveforms. see page 1-12.
:3
TEXAS 2-5
INSTRUMENlS
2-6
TYPES SN54ALS01, SN74ALS01
WITH OPEN·COLLECTOR OUTPUTS
02661, APRIL 1982-REVISEO DECEMBER 1983

and Ceramic DIPs
o Dependable Texas Instruments Quality
and Reliability
SN54ALSOl . . • J PACKAGE
description SN74ALS01 • . . N PACKAGE
1Y VCC
Y = A' B or Y = A + 8 in positive logic. The open-
collector outputs require pull-up resistors to perform 1A 4Y
correctly. They may be connected to other open- 1B 4B
collector outputs to implement active-low wired-OR 2Y 4A
or active-high wired-AND functions. Open-collector 2A 3Y
devices are often used to generate higher VOH 2B 3B
levels. GND 3A
The SN54ALS01 is characterized for operation over

the full military temperature range of - 55°C to
1 25°C. The SN7 4ALSO 1 is characterized for opera- SN54ALS01 • . • FH PACKAGE
tion from ooC to 70°C. SN74ALS01 • . . FN PACKAGE
(TOP VIEW)
..
U
FUNCTION TABLE (each gate) ~>-uu>-
...-...-z>q-
INPUTS OUTPUT
A B Y 1B 4B
H H L NC NC
L X H 2Y 4A en
X L H NC
2A
NC
3Y
!::
logic symbol ~
u
(21
IllOU~1ll
NZZMM
a:
lA
18
(31
&
0 ~
NC-No internal connection
u
(51 en
2A
28
(61 <t
3A
(81 C
38
(91 Z
4A
(111 <t
4B
(121 en
...I
<t
-TEXAS 2-7
INSTRUMENTS
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
- Supply voltage, V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74ALS01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50 DC

SN54ALS01 SN74ALS01
- MIN NOM MAX MIN NOM MAX
UNIT

VOH High-level output voltage 5.5 5.5 V
IOl low-level output current 4 8 mA
TA Operating free-air temperature -55 125 0 70 De
SN54ALS01 SN74ALS01
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
lIB VOL
II
Vee = 4.5 V.
Vec = 4.5 V,
VCC = 5.5 V.
IOl = 4 mA
IOl = 8 mA
VI = 7 V
0.25 0.4
0.1
0.25
0.35
0.4
0.5
0.1
V
mA
l>
,.... IIH VCC,:" 5.5 V. VI = 2.7V 20 20 ~A
III VCC = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
CJ)
ICCH Vce - 5.5 V. VI - 0 V 0.43 0.85 0.43 0.85 mA
l> ICCl Vec = 5.5 V. VI = 4.5 V 1.62 3 1.62 3 mA
2 tAli typical values are at Vee = 5 V. TA = 25°e
C
l> switching characteristics (see Note 1)
CJ) Vcc = 4.5 V to 5.5 V.
o FROM TO
CL = 50 pF.
Rl = 2 kQ.
$ PARAMETER UNIT
o (lNPUTI (OUTPUTI TA = MiN to MAX
c MIN
SN54AlS01
MAX MIN
SN74ALS01
MAX
=i
CJ) tpLH A or B Y 23 59 23 54 ns
NOTE 1: For load circuit and voltage waveforms, see page 1-12.
12
2-8 TEXAS
INSTRUMENTS
TYPES SN54ALS02, SN54AS02, SN74ALS02, SN74AS02
QUADRUPLE 2·INPUT POSITIVE·NDR GATES
02661. APRIL 1982-REVISED DECEMBER 1983

and Ceramic DIPs
and Reliability
description SN54ALS02. SN54AS02 ••• J PACKAGE
SN74ALS02. SN74AS02 ••• N PACKAGE
These devices contain four independent 2-input NOR
(TOP VIEW)
gates. They perform the Boolean functions
Y = A + B or Y = A' B in positive logic. VCC
4Y
The SN54ALS02 and SN54AS02 are characterized 1B 4B
for operation over the full military temperature range 2Y 4A
of -55°C to 125°C. The SN74ALS02 and 2A 3Y
SN74AS02 are characterized for operation from 0 °C 2B 3B
to 70°C.
3A
INPUTS OUTPUT
SN54ALS02. SN54AS02 ••• FH PACKAGE
A B Y
SN74ALS02. SN74AS02 ••• FN PACKAGE
H X L
(TOP VIEW)
X H L
U
L L H 4:>-UU>-
.-.-Z>'<t
logic symbol 3 2 1 2019
(2)
;;>1 1B 4B
1A
NC NC
1B
(3)
2Y 4A en
2A
(5)
NC NC !:::
28
(6)
3Y ::>
3A
(8) ()
38
(9) ~
4A
(11) ()
48
(12)
en
«
c
z
«
en
...J
«
TEXAS 2-9
INSTRUMENTS
QUADRUPLE 2·INPUT POSITIVE·NOR GATES
Supply voltage, V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C

I SN54AlS02 SN74AlS02
UNIT
VIL Low·level input voltage 0.8 0.8 V
IOH High·level output current -0.4 -0.4 mA
IOL Low-level output current 4 8 mA
SN54AlS02 SN74AlS02
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V, 10L = 4 mA 0.25 0.4 0.25 0.4
V
~
VOL
Vee = 4.5 V, 10L = 8 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 Il A
>
r
IlL Vee = 5.5 V,
= 5.5 V,
VI = 0.4 V
Vo = 2.25 V
-0.1 -0.1 mA
en 10*
leeH
Vee
Vee = 5.5 V, VI = OV
-30
0.86
-112
2.2
-30
0.86
-112
2.2
mA
mA
>
:2
leeL Vee = 5.5 V,
tAli typical values are at Vee = 6 V. TA = 26°e.
VI = 4.5 V 2.16 4 2.16 4 mA
C *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
>
Vcc = 4.5 V to 5.5 V,
o Cl = 60 pF,
:a FROM TO Rl = 500 Q,
o PARAMETER
UNIT
c SN54AlS02 SN74AlS02
=t MIN MAX MIN MAX
en tPLH A orB Y 3 14 3 12 ns
tpHL A orB Y 3 11 3 10 ns
2-10 TEXAS
INSTRUMENlS
TYPES SN54AS02, SN74AS02
QUADRUPLE 2·INPUT POSITIVE·NOR GATES
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e t~ 125°C
SN74AS02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C

SN54AS02 SN74AS02
UNIT
Vec Supply voltage 4.5 5 5.5 4.5 5 5.5 V
IOH High-level output current -2 -2 rnA
IOl low-level output current 20 20 rnA
TA Operating free-air temperature -- -55 125 0 70 °e
SN54AS02 SN74AS02
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, "IOH= -2 rnA Vee- 2 Vec- 2 V
VOL Vee = 4.5 V, 10l = 20 rnA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7V 20 20 IJA
III Vee = 5.5 V. VI = 0.4 V -0.5 -0.5 rnA
10:1: Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
CIJ
lecH Vee = 5.5 V, VI = 0 V 3.7 5.9 3.7 5.9 rnA !:::
Icel Vee = 5.5 V. VI = 4.5 V 12.5 20.1 12.5 20.1 rnA ::>
tAli typical valuas are at Vee = 5 V. TA = 25°e.
u
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS' a:
U
switching characteristi~s (see Note 1)
CIJ
Vcc = 4.5 V to 5.5 V.
CL = 50 pF,
«
FROM TO RL = 500 Q,
C
PARAMETER UNIT 2
(INPUT) (OUTPUT)
SN54AS02
TA = MIN to MAX
SN74AS02
«
MIN MAX MIN MAX CIJ
-I
tPlH
tpHl
A or B
A or B
Y
Y
1
1
5
5
1
1
4.5
4.5
ns
ns
«
TEXAS 2-11
INSTRUMENTS
2-12
TYPES SN54ALS03A, SN74ALS03A
02661. APRIL 1982-REVISEO DECEM8ER 1983

and Ceramic DIPs
and Reliability
SN54ALS03A . . • J PACKAGE
description
SN74ALS03A . . . N PACKAGE
NAND gates. They perform the Boolean functions 1A VCC
y = A' B or Y = A+ B in positive logic. The open- 1B 4B
collector outputs require pull-up resistors to perform 1Y 4A
correctly. They may be connected to other open- 2A 4Y
collector outputs to implement active-low wired-OR 2B 3B
or active-high wired-AND functions. Open-collector 3A
2Y
devices are often used to generate higher VOH GND 3Y
levels.
The SN54ALS03A is characterized for operation

over the full military temperature range of - 55 DC to SN54ALS03A • . . FH PACKAGE
125 DC. The SN74ALS03A is characterized for SN74ALS03A . . . FN PACKAGE
operation from 0 DC to 70 DC. (TOP VIEW)
U
aJ<t:UUaJ
...-...-Z><:t
INPUTS OUTPUT 1Y 4A
A B V NC NC
H H L 2A 4Y
L X H NC NC CI'J
X L H 2B 3B !::
logic symbol :J
CJ
a:
1A C3
18 NC - No internal connection CI'J
2A «
28
c
3A z
38
4A
«
CI'J
..J
«
48
TEXAS 2-13
INSTRUMENTS
absolute maximum ratings over operating free·alr temperature range (unless otherwise noted)
Supply voltage, Vee . . . . . . . . ....................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....... 7 V
Operating free-air temperature range: SN54ALS03A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS03A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C
Storage temperature range ............. .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C
recC?mmended operating conditions

SN54AlS03A SN74AlS03A
UNIT
..
MIN TYPt -MAX MIN TYPt MAX
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
Vee = 4.5 V, IOl = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOl = 8 rnA 0.35 0.5
Vee = 5.5 V, VI = 7 V
»
r-
II
IIH Vee = 5.5 V, VI = 2.7V
0.1
20
0.1
20
rnA
~A
Vee = 5.5 V, VI = 0.4 V
o III
leeH Vee = 5.5 V, VI = OV 0.43
-0.1
0.85 0.43
-0.1
0.85
rnA
rnA
»
2
leel
tAli typical values are at Vee
Vee = 5.5 V,
= 5 V. TA = 25°e
VI = 4.5 V 1.62 3 1.62 3 rnA
C
»
en
Vcc = 4.5 V to 5.5 V,
~ FROM TO
Cl = 50 pF.
Rl = 2 kQ.
::IJ PARAMETER UNIT
o (INPUT) (OUTPUTI
SN54AlS03A
TA = MIN to MAX
SN74AlS03A
C
~
MIN MAX MIN MAX
o tplH
tpHl
A or B
A or B
Y
Y
23
5
59
26
23
5
54
22
ns
ns
NOTE 1: For load circuit and voltage waveforms. see page 1-12.
2-14 TEXAS
INSTRUMENTS
TYPES SN54ALS04A, SN54AS04, SN74ALS04A, SN74AS04
HEX INVERTERS
02661. APRIL 1982-REVISEO DECEMBER 1983

and Ceramic DIPs
e Dependable Texas Instruments Quality
and Reliability
description SN54ALS04A.SN54AS04 ..• JPACKAGE

SN74ALS04A. SN74AS04 ••. N PACKAGE
These devices contain six independent inverters.
(TOP VIEW)
They perform the Boolean function Y = A.
1A VCC
The SN54ALS04A and SN54AS04 are character- 1Y 6A
ized for operation over the full military temperature 2A 6Y
range of - 55 DC to 125 DC. The SN74ALS04A and 2Y 5A
SN74AS04 are characterized for operation from 0 DC 3A 5Y
to 70 D C. 3Y 4A
4Y
FUNCTION TABLE
(each inverter)
INPUT OUTPUT SN54ALS04A. SN54AS04 '.' . FH PACKAGE

A Y SN74ALS04A. SN74AS04 ... FN PACKAGE
H L (TOP VIEW)
L H u
>-«uu«
.-.-z>(O
logic symbol 4 6Y en
lA
(11
(31 2Y
5
6
NC !::
2A 5A ::J
3A
(51 NC 7 NC U
4A
(91 3A 8 5Y a:
5A
(111 U
(13) >-ou>-«
MZZq-q- tn
«
6A
t!)

C
2
«
en
-I
«
TEXAS 2-15
INSTRUMENlS
HEX INVERTERS
Supply voltage, Vee ........... '.................................................... 7 V
Input voltage ...... : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS04A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS04A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 °e

SN54ALS04A SN74ALS04A
UNIT
VIL Low-level input voltage O.B 0.8 V
IOH High-level output current -0.4 -0.4 rnA
IOL Low-level output current 4 8 rnA
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1;5 V
VOH Vee = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2 V
Vee = 4.5 V. IOl = 4 rnA 0.25 0.4 0.25 0.4
VOL V
ItJ II
IIH
Vee
Vee
Vee
= 4.5 V.
= 5.5 V.
= 5.5 V.
IOl = 8 rnA
VI = 7 V
VI = 2.7V
0.1
20
0.35 0.5
0.1
20
rnA
jAA
>
r-
III
10~
Vee
Vee
= 5.5 V.
= 5.5 V.
VI = 0.4 V
Vo = 2.25 V -15
-0.1
-70 -15
-0.1
-70
rnA
rnA
VJ leeH Vee = 5.5 V. VI = OV 0.65 1.1 0.65 1.1 rnA
>
2
leel Vee = 5.5 V.
VI = 4.5 V 2.9 4.2 2.9 4.2 rnA
C *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
G; switching characteristics (see Note 1)

Vec = 4.5 V to 5.5 V.
Q CL = 50 pF.
::xJ PARAMETER
FROM TO RL = 500 Q.
UNIT
(') (INPUT) (OUTPUT) TA = MIN to MAX
c: SN54ALS04A SN74ALS04A
=i MIN MAX MIN MAX
VJ tplH A Y 3 14 3 11 ns
tpHl A Y 2 12 2 8 ns
2-16 TEXAS
INSTRUMENTS
TYPES SN54ASD4, SN74ASD4
HEX INVERTERS
Supply voltage, Vee ............................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74AS04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooe to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . . . . ' ........ - 65°C to 1 50 °e

SN54AS04 SN74AS04
UNIT
VIH High-level input vciltage 2 2 V
VIL Low-level input voltage O.B O.B V
10H High-level output current -2 -2 rnA
10L Low-level output current 20 20 rnA
electrical characteristics over recommended operating free-air temperatur~ range (unless otherwise noted)
SN54AS04 SN74AS04
VIK Vee = 4.5 V, II = -1B rnA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V, 10L = 20 rnA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7V 20 20 j.lA
IlL
10*
Vee
Vee
= 5.5 V,
= 5.5 V,
VI = 0.4 V
Vo = 2.25 V -30
-0.5
-112 -30
-0.5
-112
rnA
rnA
en
leeH Vee = 5.5 V, VI = OV 3 4.B 3 4.B rnA
!::
leeL Vee = 5.5 V, VI = 4.5 V 14 26.3 14 26.3 rnA
::J
(.)
*The output conditions have been chosen to produce a current th~t closely approximates one half of the true short-circuit output current. lOS' a::
(.)
en
Vcc = 4.5 V to 5.5 V,
Cl = 50 pF.
«
C·
PARAMETER
FROM 'to Rl = 500 Q.
UNIT 2
(INPUT) (OUTPUT)
SN54AS04
TA = MIN to MAX
SN74AS04
«
MIN MAX MIN MAX en
..J
tplH
tpHL
A
A
Y
Y
1
1
6
4.5
1
1
5
4
ns
ns
«
NOTE 1: For load Circuit and voltage waveforms. see page 1-1 2.
TEXAS 2-17.
INSTRUMENTS
- l>
r-
en
l>
z
c
l>
en
Q
::t1
o
c
=i
en
2-18
HEX INVERTERS WITH OPEN·COLLECTOR OUTPUTS

and Ceramic DIPs
and Reliability
SN64ALS06A ••• J PACKAGE
description SN74ALS06A ••• N PACKAGE
These devices contain six independent inverters. (TOPVIEWI
They perform the Boolean function Y = A. The open-
1A VCC
collector outputs require pull-up resistors to perform
1Y 6A
correctly. They may be connected to other open-
2A 6Y
collector outputs t!J implement active-low wired-OR
2Y 5A
or active-high wired-AND functions. Open-collector
3A 5Y
devices are often used to generate higher VOH
3Y 4A
levels. .
GND 4Y
over the full military temperature range of - 55 DC to
125 DC. The SN74ALS05A is characterized for
SN64ALS06A ••• FH PACKAGE
operation from 0 DC to 70 DC.
SN74ALS06A ..• FN PACKAGE
(TOP VIEW)
FUNCTION TABLE (each inverter)
u
INPUT OUTPUT >-<{uu<{
.--.--z> (0
A Y
H L
L H 2A 6Y
NC NC CJ)
2Y 5A
logic symbol
NC NC
!::
5Y
::J
()
1A a:
2A >-ou>-<{ ()
C"lzz'<t'<t
3A (!)
CJ)
4A
NC - No internal connection «
SA
6A
c
2
«
CJ)
...I
«
TEXAS 2-19
INSTRUMENTS
TYPES SN54ALS05A. SN74ALS05A
HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... 7 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V .
SN74ALS05A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C

UNIT
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
~
Vee = 4.5 V, IOL = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 8 rnA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
»
r- IIH Vee = 5.5 V, VI = 2.7V 20 20 /lA
en IlL
leeH
Vee
Vee
= 5.5 V,
= 5.5 V,
VI = 0.4 V
VI = a V 0.65
-0.1
1.1 0.65
-0.1
1.1
rnA
rnA
»
z leeL
tAli tYPical values are at Vee
Vee = 5.5 V,
= 5 V, TA = 25°e
VI = 4.5 V 2.9 4.2 2.9 4.2 rnA
o
»
en
Vcc = 4.5 V to 5.5 V,
o CL = 50 pF,
FROM TO RL = 2 kQ,
::c PARAMETER UNIT
o (INPUT) (OUTPUT) TA = MIN to MAX
c SN54ALS05A SN74ALS05A
MAX
=i y
MIN MAX MIN
en tPLH
tpHL
A or B
A or B Y
23
4
59
19
23
4
54
14
ns
ns
2-20 TEXAS
INSTRUMENTS
TYPES SN54ALS08, SN54AS08, SN74ALS08,SN74AS08
QUADRUPLE 2·INPUT POSITIVE·AND GATES.
02661, APRIL 1982-REVISED DECEMBER 1983

and Ceramic DIPs
and Reliability
description SN54ALSOB, SN64ASOB .•• J PACKAGE

SN74ALSOB, SN74ASOB ••. N PACKAGE
These devices contain four independent 2-input AND
(TOP VIEW)
gates. They perform the Boolean functions Y = A' B
or Y = A+B in positive logic.
The SN54ALSOa and SN54ASOa are characterized
for operation over the full military temperature range
of -55°C ~ 125°C. The SN74ALSOa and
SN74ASOa are characterized for operation from 0 °e
to 70°C.
FUNCTION TABLE
(each gate)
SN64ALSOB, SN54ASOB •.• FH PACKAGE
INPUTS OUTPUT
SN74ALSOB, SN74ASOB .•. FN PACKAGE
A B Y (TOP VIEW)
H H H
U
L X L m«UUCD
..-..-z>'<t
X L L
1Y 4A
logic symbol
NC NC
2A 4Y
1A
(1) & Ne NC
(3) 1Y
(2) 36
1B
(41
2A
(6) 2Y
(5)
2B
(91
3A (81
(101 3y NC-No internal connection
3B
(12)
4A (111
(131 4y
48
TEXAS 2-21
INSTRUMENTS
TYPES SN54ALS08. SN74ALS08
QUADRUPLE 2·INPUT POSITIVE·AND GATES
Supply voltage, Vee ........................................... ; . . . . . . . . . . . . . . . . ... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooC to 70°C

SN54ALS08 SN74ALS08
UNIT
VIL Low·level input voltage O.B O.B V
10H High-level output current -0.4 -0.4 mA
SN54ALS08 SN74ALS08
VIK Vee = 4.5 V, II = -1B mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 V
Vee = 4.5 V, 10L = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10l = 8 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 ",A
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
10* Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI = 4.5 V 1.3 2.4 1.3 2.4 mA
leel Vee = 5.5 V. VI = OV 2.2 4 2.2 4 mA
tAli tYPical values are at VCC = 5 V. TA = 25°C.
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 5002.
PARAMETER UNIT
SN54ALS08 SN74ALS08
MIN MAX MIN MAX
tPlH A or B Y 4 16 4 14 ns
tpHl A orB Y 3 12 3 10 ns
2-22 TEXAS
INSTRUMENTS
TYPES SN54ASOB,SN74ASOB
Input voltage . . . . . . . . . . . . . . . ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS08 " . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AS08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C

SN64ASOB SN74AS08
UNIT
Vil low-level input voltage 0.8 O.B V
IOH High-level output current -2 -2 mA
SN54ASOB SN74AS08
..
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, 10H = -2 mA Vee- 2 Vee- 2 V
Val Vee = 4.5 V, 10l = 20 mA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 IlA
Vee = 5.5 V, VI = 0.4 V -0.5
III
10* Vee = 5.5 V, Va = 2.25 V -30
-0.5
-112 -30 -112
mA
mA
en
leeH Vee = 5.5 V, VI = 4.5 V 5.8 9.3 5.8 9.3 mA !::::
Vee = 5.5 V, VI =0 V 14.9 24 24 :::>
leel
typical values are at Vee = 5 V. T A = 25°e.
t All
14.9 mA
u
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. iOS. a:
U
en
Vee = 4.5 V to 5.5 V.
CL = 50 pF,
«
RL = 500 Q.
c
PARAMETER
FROM TO
UNIT z
IINPUT) (OUTPUTI
SN54ASOB
TA = MIN to MAX
SN74AS08
«
MIN MAX MIN MAX en
..J
tplH
tpHl
A or B
A orB
Y
Y
1
1
6.5
6.5
1
1
5.5
5.5
ns
ns
«
NOTE 1: For load CirCUit and voltage waveforms. sae page 1-12.
TEXAS 2-23
INSTRUMENTS
2-24
QUADRUPLE 2·INPUT POSITlVE·AND GATES

and Ceramic DIPs
and Reliability
SN54ALS09 • • • J PACKAGE
description SN74ALS09 ••• N PACKAGE
These devices contain four independent 2-input AND (TOP VIEW)
gates. They perform the Boolean functions Y = A' B
1A VCC
or Y = A + B in positive logic. The open-collector
1B 4B
outputs require pull-up resistors to perform correctly.
1Y 4A
They may be connected to other open-collector out-
2A 4Y
puts to implement active-low wired-OR or active-high
2B 3B
wired-AND functions. Open-collector devices are
2Y 3A
often used to generate higher VOH levels.
GND 3Y
the full military temperature range of - 55 DC to
125 DC. The SN74ALS09 is characterized for opera-
tion from 0 DC to 70 DC. SN54ALS09 • . . FH PACKAGE
SN74ALS09 . . . FN PACKAGE
FUNCTION TABLE (each gate) (TOP VIEW)
INPUTS OUTPUT U
III <t: U U III
A B Y .-.-Z> '<:I'
H H H
L X L
1Y 4A
X L L
NC NC en
logic symbol 2A 4Y !::
NC NC ::J
3B (.)
lA
(11 &
Q (31 lV
a:
(21
lB
>-OU>-<t:
(.)
NZZMM
2A (61 (!) en
2B
2v
«
3A
(8) 3V
NC - No internal connection
c
38
z
4A
(131
(111
4V «
4B
en
-J
Pin numbers shown are for J and N packages. «
TEXAS 2-25
INSTRUMENTS
Supply voltage, V CC .. '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ' .. 7 V
Input voltage ................................... ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS09 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

SN54ALS09 SN74ALS09
UNIT
VIL low-level input voltage 0.8 0.8 V
IOL low-level output current 4 8 mA
SN54AlS09 SN74ALS09
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
III VOL
II
Vee
Vee
Vee
= 4.5 V.
= 4.5 V.
= 5.5 V.
IOl = 4 mA
IOl = 8 mA
VI = 7 V
0.25 0.4
0.1
0.25
0.35
0.4
0.5
0.1
V
mA
:t> IIH Vee = 5.5 V. VI = 2.7V 20 20 Il A
~ Vee = 5.5 V. VI = 0.4 V -0.1 -0.1
III mA
CJ)
leeH Vee = 5.5 V. VI = 4.5 V 1.35 2.4 1.35 2.4 mA
:t> leel Vee = 5.5 V. VI = 0 V 2.2 4 2.2 4 mA
2 tAli typical values are at Vee = 5 V. TA = 25°C
C
:t>
CJ) Vcc = 4.5 V to 5.5 V.
o FROM TO
CL = 50 pF.
RL = 2 kQ.
:l3 PARAMETER UNIT
o (lNPUTI (OUTPUTI TA = MIN to MAX
c MIN
SN54ALS09
MAX MIN
SN74ALS09
MAX
=i
CJ) tplH A orB Y 23 59 23 54 ns
tpHl A orB Y 5 17 5 15 ns
12
2-26 TEXAS'
INSTRUMENTS
POST OFFiCe BOX 225012 • DALLAS, TeXAS 75265
TYPES SN54ALS10. SN54AS10. SN74ALS10.SN74AS10
TRIPLE 3·INPUT POSITIVE·NAND GATES

and Ceramic DIPs
and Reliability
description SN54ALS10. SN54AS10 ••. J PACKAGE

These devices contain three independent 3-input
(TOP VIEW)
Y = A·B·C or Y = A+B+C in positive logic. lA 1 U14 VCC
1B 2 13 lC
The SN54ALS 10 and SN54AS 10 are characterized
2A 12 lY
2B 4 11 3C
of -55°C to 125°C. The SN74ALS10 and
2C 5 10 3B
SN7 4AS 10 are characterized for operation from 0 °C
2Y 6 9 3A
to 70°C.
GND 7 8 3Y
INPUTS OUTPUT SN54ALS10. SN54AS10 ••• FH PACKAGE

A B C y SN74ALS10. SN74AS10 .•• FN PACKAGE
H H H L (TOP VIEW)
L X X H
X L X H
X X L H
2A lY
NC
2B
NC
3C
en
logic symbol NC NC !:::
(11 2C 38 :J
1A &
U
18
(21
a:
(131 >-ou>-<!
lC NZZMM
(!)
U
(31
2A
en
28
(41
(51
«
2C
(9) c
3A
2
3B
(10)
(111
«
3C
en
...J
«

12
TEXAS 2-27
INSTRUMENTS
Supply voltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . ' ... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range ......... ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 °e

SN54ALS10 SN74ALS10
UNIT
SN54ALS10 SN74ALS10
MIN TVPt MAX MIN TVPt MAX
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V. 10H = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V. 10L = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. 10L = 8 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 ",A
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
lo~ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V. VI = OV 0.32 0.6 0.32 0.6 mA
leeL Vee = 5.5 V. VI = 4.5 V 1.2 2.2 1.2 2.2 mA
= 5 V, TA = 25°e.
t All typical values are at Vee
tThe output conditions have baen chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54ALS10 SN74ALS10
MIN MAX MIN MAX
tpLH Any V 3 14 3 11 ns
tpHL Any Y 4 21 4 18 ns
NOTE 1: For load cIrcuIt and voltage waveforms, see page 1-12.
12
2-28 TEXAS
INSTRUMENlS
POST OFFICE BOX 225012 • DALLAS, TeXAS 75265
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74AS10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooe to 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 °e

SN54AS10 SN74AS10
UNIT
TA Operating free-air temperature -55 125 . 0 70 °e
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)'
SN54AS10 SN74AS10
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
VOL Vee = 4.5 V, 10L = 20 mA 0.35 0.5 0.35 0.5 V
II VCC = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 /lA
IlL Vee = 5.5 V, VI = 0.4 V -0.5 -0.5 mA
C/)
10* Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI = OV 1.5 2.4 1.5 2.4 mA !:::
leeL Vee = 5.5 V, VI = 4.5 V 8.1 13 8.1 13 mA ::J
tAli typical values are at Vee = 5 V. TA = 25°e. U
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' a::
U
C/)
Vcc = 4.5 V to 5.5 V, cd:
CL = 50 pF,
c
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL = 500 Q,
TA = MIN to MAX
UNIT z
SN54AS10 SN74AS10
cd:
MIN MAX MIN MAX C/)
tpLH Any Y 1 5 1 4.5 ns
..oJ
tpHL Any Y 1 5 1 4.5 ns cd:
TEXAS 2-29
INSTRUMENTS
~
l>
r-
o
l>
:2
C
l>
o
Q
::D
o
c
=i
o
2-30
TRIPLE 3·INPUT POSITIVE·AND GATES
02661, APRIL 1982-REVISEO DECEM8ER 1983

and Ceramic DIPs
and Reliability

(TOP VIEW)
AND gates. They perform the Boolean functions
Y = A' B' C or Y = A + B + C in positive logic. 1A VCC
1B 1C
The SN54ALS11 and SN54AS11 are characterized 2A 1Y
2B 3C
2C 3B
SN7 4AS 11 are characterized for operation from 0 °C
2Y 3A
to 70°C.
3Y

SN54ALS11. SN54AS11 " . FH PACKAGE
INPUTS OUTPUT
A B C Y
(TOP VIEW)
H H H H
u
L X X L co<{uuu
.-z>.-
X L X L
X X L L
2A 1Y
NC NC
2B 3C en
logic symbol NC NC !=
3B =>
lA
(11
& u
18
(21
a:
(131
lC U
(31
2A
(41
NC-No internal connection en
28
(51
<C
2C
(91 C
3A
(101
:2
38
(111
<C
3C

en
..J
<C
TEXAS 2-31
INsrRUMENTS
POST OFFiCe BOX 225012 • DALLAS. TexAS 75265
Supply voltage, V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .......... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

SN54ALS11 SN74ALS11
UNIT
SN54ALS11 SN74ALS11
VIK Vee = 4.5 V. II = -18mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V, 10l = 4 mA 0.25 0.4 0.25 0.4
VOL V
16 II
IIH
Vee
Vee
Vee
= 4.5 V.
= 5.5 V,
= 5.5 V,
10L = 8 mA
VI = 7 V
VI = 2.7V
0.1
20
0.35 0.5
0.1
20
mA
jAA
»
r-
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
en 10*
leeH
Vee = 5.5 V.
Vee = 5.5 V.
Vo = 2.25 V
VI = 4.5 V
-30 -112
1
-30
1.8
-112
1 1.8
mA
mA
»
z
leel Vee = 5.5 V.
tAU tYPical values are at Vee = 5 V. TA = 25°e.
VI = 0 V 1.6 3 1.6 3 mA
c *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
»
VCC = 4.5 V to 5.5 V,
Q CL = 60 pF.
::D FROM TO RL = 500Q.
o PA~METER
UNIT
c SN54ALS11 SN74ALS11
=i MIN MAX MIN MAX
en tPlH Any Y 5 23 5 20 ns
tpHl Any Y 3 12 3 10 ns
2-32 TEXAS
INSTRUMENTS
TRIPLE 3·INPUT POSITlVE·AND GATES
Supply voltage. V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 1 25 °C
SN74AS11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70 o C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 °c

SN54AS11 SN74AS11
UNIT
SN54AS11 SN74AS11
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V. 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V. 10L = 20 rnA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee - 5.5 V. VI- 2.7V 20 20 ",A
IlL Vee = 5.5 V. VI = 0.4 V '-0.5 -0.5 mA
10* Vee - 5.5 V. Vo - 2.25 V -30 -112 '-30 -112 rnA
en
leeH Vee = 5.5 V. VI = 4.5 V 4.3 7 4.3 7 mA !=
leeL Vee = 5.5 V. VI = OV 11.2 18 11.2 18 rnA ::J
t All typical values are at VCC = 5 V. T A = 25°C. CJ
tThe output conditions have baen chosen to produca a current that closely approximates one half of the true short-circuit output current. lOS.
I
a::
CJ
en
,
Vcc = 4.5 V to 5.5 V. «
FROM TO
CL = 50 pF.
RL = 5002.
c
PARAMETER UNIT z
(INPUT) (OUTPUT)
SN54AS11
TA =.MIN to MAX
SN74AS11 «
MIN MAX MIN MAX en
...J
tpLH
tpHL
Any
Any
Y
Y
1
1
6.5
6.5
1
1
6
5.5
ns
ns «
:3
TEXAS 2-33
INSTRUMENTS
lID
l>
r-
t/)
l>
2
C
l>
en
o
::D
o
c:
=i
en
2-34··

and Ceramic DIPs
and Reliability
SN54ALS12 . • . J PACKAGE
description SN74ALS12 . . . N PACKAGE
These devices contain three independent 3-input (TOP VIEW)
NAND gates with open-collector outputs. These
1A VCC
gates perform the Boolean functions Y = A' B' C or 1C
18
Y = Ii: + B + C in positive logic. The open-collector
2A 1Y
28 3C
2C 38
2Y 3A
GND 3Y

the full military temperature range of - 55 DC to
125 DC. The SN74ALS12 is characterized for opera- SN54ALS12 . . . FH PACKAGE
tion from 0 DC to 70 DC. SN74ALS12 . • • FN PACKAGE
(TOP VIEW)
U
INPUTS OUTPUT CIl<{UUU
z>.-
A B C Y
H H H L
2A 1Y
X
L X
L
X
X
H
H NC NC en
X X L H
2B 3C !::
NC NC ::l
2C 3B U
logic symbol
a:
U
(11
1A &
en
18
lC
c
2A
z
28
«
2C
3A
en
..J
38
(111
«
3C
TEXAS 2-35
INSTRUMENTS
Input voltage . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 1 25°C
SN74ALS12 ............. '0' • • • • • • • • • • • • • • • • • • • • • 0 °e to 70°C
Storage temperature range . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50 DC

SN54ALS12 SN74ALS12
UNIT
VIH High-level Input voltage 2 2 V
SN54ALS12 SN74ALS12
..
VIK Vec = 4.5 V, "= -18 rnA -1.5 -1.5 V
IOH Vce = 4.5 V, VOH = 6.5 V 0.1 0.1 rnA
Vcc = 4.6 V, IOL = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vcc = 4.5 V, IOL = 8 rnA 0.35 0.5
II Vcc = 5.5 V, VI = 7 V 0.1 0.1 rnA
~ "H Vcc = 5.5 V, V, = 2.7V 20 20 /AA
r- ',L Vcc = 5.5 V, V, = 0.4 V -0.1 -0.1 rnA
o ICCH Vce = 5.5 V, VI = OV 0.32 0.6 0.32 0.6 rnA
~ ICCL Vcc = 5.5 V, VI = 4.5 V 1.2 2.2 1.2 2.2 rnA
2 tAli typical values are at Vee = 5 v, TA = 25°C
C
~ switching characteristics (see Note 1)
o Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
~ FROM TO RL = 2 kQ,
:u PARAMETER UNIT
c: MIN
SN54ALS12
MAX MIN
SN74ALS12
MAX
=i tpLH Any Y 23 59 23 54 ns
o tpHL Any Y 9 37 9 30 ns
12
2-36 TEXAS
INSTRUMENTS

and Ceramic DIPs
and Reliability
SN54ALS15 . . . J PACKAGE
description SN74ALS15 . • . N PACKAGE
These devices contain three independent 3-input (TOP VIEW)
AND gates with open-collector outputs. These gates
1A VCC
perform the Boolean functions Y = A' B' C or
1B 1C
Y = A + B + C in positive logic. The open-collector
2A 1Y
2B 3C
2C 3B
2Y 3A
GND 3Y

the full military temperature range of - 55 °C to
125 °C, The SN74ALS15 is characterized for opera- SN54ALS15 . . . FH PACKAGE
tion from 0 °C to 70 o C. SN74ALS15 . . • FN PACKAGE
(TOP VIEW)
FUNCTION TABLE (each gate) U

m<f:UUu
.-2>.-
INPUTS OUTPUT
3 2 1
A B C y
H H H H 2A 1Y
X X NC NC
L
X L X
L
L 2B 3C en
X X L L
NC NC !=
2C 3B :J
logic symbol
CJ
a:
CJ
lA
(11 & en
lB
(21
Q
(12)
lY NC - No internal connection «
lC
(131
c
2A
(31
z
28
(41 (61
2Y «
2C
(51
(91
en
...J
3A
38
(101
(111
(81
3Y «
3C
TEXAS 2-37
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN 54ALS1 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 1 25°C
SN74ALS15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C

SN54ALS16 SN74ALS16
UNIT
SN54ALS15 SN74ALS15
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 mA
~
Vee = 4.5 V, IOL = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 8 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
l> IIH Vee =·5.5 V, VI = 2.7V 20 20 Il A
r-
en IlL
leeH
Vee
Vee
= 5.5
= 5.5
V.
V.
VI = 0.4 V
VI = 4.5 V 1
-0.1
1.8 1
-0.1
1.8
mA
mA
l> leeL Vee = 5.5 V. VI = 0 V 1.66 3 1.66 3 mA
2 tAli typical values ara at Vee = 5 V. TA = 25°C
C
l>
en Vcc = 4.5 V to 5.5 V,
o FROM TO
CL = 50 pF,
RL = 2 kQ.
::u PARAMETER UNIT
c MIN
SN54ALS15
MAX MIN
SN74ALS15
MAX
=i
en tpLH
tpHL
Any
Any
V
Y
23
6
59
14
23
6
54
13
ns
ns
NOTE 1: For load Circuit and voltaga waveforms, see page 1-12.
2-38 TEXAS
INSfRUMENlS
DUAL 4·INPUT POSITIVE·NAND GATES

and Ceramic DIPs
and Reliability
description SN54ALS20A, SN54AS20 •.. J PACKAGE

SN74ALS20A, SN74AS20 ••• N PACKAGE
These devices contain two independent 4-input
(TOP VIEW)
y = A'B'C'D or Y = A+B+C+D in positive logic.
The SN54ALS20A and SN54AS20 are character-
ized for operation over the full military temperature
range of - 55 °C to 125 DC. The SN74ALS20A and
SN7 4AS20 are characterized for operation from 0 °C
to 70 DC.
INPUTS OUTPUT SN54ALS20A, SN54AS20 ••• FH PACKAGE

A B C 0 y SN74ALS20A, SN74AS20 ••• FN PACKAGE
H H H H L (TOP VIEW)
L X X X H U
CJ<{UUCl
X L X X H .... Z>N
X X L X H
3 2 1 2019
X X X L H
NC 2C
NC NC en
1C NC
NC NC !=
logic symbol ::>
10 2B
u
lA
(1) & a::
lB
(2)
1Y
u
lC en
10
cd:
2A c
2B
2Y
z
2C
(13)
cd:
20
en
..J
cd:
Copyright © 19B2 by Texas Instruments Incorporated
TEXAS 2-39
INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TeXAS 75265
Supply voltage, Vee ................ : .............................................. 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS20A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74ALS20A ........ , .......................... 0 DC to 70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 150 DC
recommended operatl.ng conditions

UNIT
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V. IOH = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V. IOL = 4 mA 0.25 0.4 0.25 0.4
VOL V
IB II
IIH
Vee
Vee
Vee
= 4.5 V.
- 6.5 V.
= 5.5 V.
IOL = 8 mA
VI - 7 V
VI = 2.7V
0.1
20
0.35 0.5
0.1
20
mA
IJ.A
l> III Vee = 6.6 V. VI = 0.4 V -0.1 -0.1 mA
r- lo~ Vee = 6.5 V. Vo = 2.26 V -15 -70 -15 -70 mA
en leeH Vee = 6.5 V. VI = OV 0.22 0.4 0.22 0.4 mA
l> leel Vee = 6.6 V. VI = 4.6 V 0.81 1.5 0.81 1.5 mA
2 tAli typical values are at Vee = 5 V. TA = 25°e.
.l> switching characteristics (see Note 1)
en
VCC = 4.5 V to 6.5 V,
~ Cl = 50 pF.
:lJ FROM TO RL = 500 Q.
o PARAMETER
UNIT
c SN54AlS20A SN74AlS20A
=i MIN MAX MIN MAX
en tPlH Any V 3 13 3 11 ns
tpHl Any V 3 12 3 10 ns
NOTE 1: For load CirCUit and voltage waveforms. see page 1-12.
121
2-40 TEXAS
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e

SN54AS20 SN74AS20
UNIT
10l low-level output current 20 20 mA
SN54AS20 SN74AS20
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, IOH = -2mA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V, 10l = 20 mA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 ",A
III Vee = 5.5 V. VI = 0.4 V -0.5 -0.5 mA (J)
10* Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI =0 V 1 1.6 1 1.6 mA
!::
leel Vee = 5.5 V, VI = 4.5 V 5.4 8.7 5.4 8.7 mA
:::>
CJ
tAli typical values are at VCC = 5 V. TA = 25 ·C.
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
a:
C3
switching characteristics (see Note 1) (J)
VCC = 4.5 V to 5.5 V. c:(
CL = 50 pF. C
PARAMETER
FROM TO RL = 500 Q. UNIT Z
(INPUT) (OUTPUT) TA = MIN to MAX c:(
SN54AS20 SN74AS20
(J)
MIN MAX MIN MAX
....I
tplH Any Y 1 5.5 1 5 ns c:(
tpHl Any Y 1 5 1 4.5 ns
NOTE 1: For load circuit and voltage waveforms. see page 1-12_
283
TEXAS 2-41
INSTRUMENTS
IIfJ
»
r-
en
»
2
C
»en
(")
ij
(")
c
=i
en
2-42
TYPES SN54ALS21. SN54AS21. SN74ALS21. SN74AS21
DUAL 4·INPUT POSITlV·E·AND GATES

and Ceramic DIPs
and Reliability
description SN54ALS21, SN54AS21 ••• J PACKAGE

SN74ALS21, SN74AS21 ••• N PACKAGE
These devices contain two independent 4-input AND
(TOP VIEW)
Y = A-B·C·D or Y = A+B+C+D in positive logic. VCC
2D
The SN54ALS21 and SN54AS21 are characterized
2C
NC
2B
SN74AS21 are characterized for operation from 0 °C
2A
to 70°C.
2Y

INPUTS OUTPUT SN74ALS21, SN74AS21 •.• FN PACKAGE
A B C 0 y
(TOP VIEW)
..
H H H H H
U
L X X X L mc:{UUO
~~Z>N
X L X X L
X X L X L 3 2 1 2019
X X X L L 2C
NC
NC en
logic symbol NC
2B
t::
1A (1) &
::l
(.)
1B (2)
(61
1Y >-OU>-c:{ a:
1C
~ZZNN
Cl (j
10
NC-No internal connection en
2A
2B
«
(8)
2Y c
2C
z
20
«
en
...J
«

:12
TEXAS 2-43
INSTRUMENTS
DUAL 4·INPUT POSITIVE·AND GATES
Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AlS21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AlS21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

SN54ALS21 SN74ALS21
UNIT
10H High-level output current -0.4 -0.4 rnA
10l low-level output current 4 8 rnA
SN54AlS21 SN74ALS21
..
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V. 10H = -0.4 rnA Vee- 2 Vee- 2 V
Vee = 4.5 V. 10l = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. 10l = 8 rnA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 ",A
l> III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
r- 10* Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
CA leeH Vee = 5.5 V, VI = 4.5 V 0.67 1.2 0.67 1.2 rnA
l> leel Vee = 5.5 V, VI = 0 V 1.1 2 1.1 2 rnA
2 tAli typical values are at Vee = 5 V. TA = 25 oe.

Vcc = 4.5 V to 5.5 V.
Q CL = 50 pF,
:z:J FROM TO RL = 500Q.
n PARAMETER
UNIT
c: SN54ALS21 SN74ALS21
~ MIN MAX MIN MAX
en tPlH Any Y 6 30 6 26 ns
tPHl Any Y 3 12 3 10 ns
128
2-44 TEXAS
INSTRUMENTS
DUAL 4·INPUT POSITIVE·AND GATES
Supply voltage, Vcc ............................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS21 ................................. - 55 °C to 125°C
SN74AS21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

SN54AS21 SN74AS21
UNIT
SN54AS21 SN74AS21
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V. IOH = -2 mA Vee- 2 Vce- 2 V
VOL Vee = 4.5 V. IOL = 20 mA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 IJA
= 5.5 V, VI = 0.4 V
IlL
10*
Vee
Vee = 5.5 V, Vo = 2.25 V -30
-0.5
-112 -30
-0.5
-112
mA
mA
en
leeH Vee = 5.5 V, VI = 4.5 V 2.9 4.6 2.9 4.6 mA
t:::
leeL Vee = 5.5 V. VI = OV 7.4 12 7.4 12 mA -
::J.
(..)
typical values are at Vee = 5 V. TA = 25 DC.
t All
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS- a:
(..)
en
VCC = 4.5 V to 5.5 V. <t
CL = 50 pF. C
PA~METER
FROM TO RL = 500 Q. UNIT Z
(INPUT) (OUTPUT) TA = MIN to MAX <t
SN54AS21 SN74AS21
MIN MAX MIN MAX en
-I
tPLH
tpHL
Any
Any
V
V
1
1
6.5
6.5
1
1
6
6
ns
ns
<t
93
TEXAS 2-45
INSTRUMENTS
2-46

and Ceramic DIPs
and Reliability
SN54ALS22A . • . J PACKAGE
description SN74ALS22A . . . N PACKAGE
(TOP VIEW)
NAND gates. These gates perform the Boolean func- 1A VCC
tions Y = A·B·C·D or Y = A+B+C+D in positive 1B 20
logic. The open-collector outputs require pull-up NC 2C
resistors to perform correctly. They may be con- 1C NC
nected to other open-collector outputs to implement 10 2B
active-low wired-OR or active-high wired-AND func- 1Y 2A
tions. Open-collector devices are often used to GNO 2Y
generate higher VOH levels.

over the full military temperature range of - 55°C to SN54ALS22A • . . FH PACKAGE
125 ac. The SN74ALS22A is characterized for SN74ALS22A . • • FN PACKAGE
operation from 0 °C to 70 ac. (TOP VIEW) \
U
co«UUQ
FUNCTION TABLE (each gate) ........ Z>N
INPUTS OUTPUT
A B C D V 2C
H H H H L NC
L X X X H NC en
X L X
L
X H
H
NC
28
!::
X X X
:::J
X X X L H ()
a:
logic symbol ()
en
1A
(1) &
<t
1B
1Y
C
1C z
10 <t
2A en
..J
28
2C
2Y <t
(13)
20
TEXAS 2-47
INSTRUMENTS
TYPES SN54ALS22A,SN74ALS22A
absolute maximum ratings over ,operating free·alr temperature range (unless otherwise noted)
Supply voltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS22A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto 70 0 e

UNIT
VOH High-level output voltage 5.5· 5.5 V
electrical characteristics over recommended operating free·air temperature range (unless otherwise noted)
MIN TVPt MAX MIN TYPt MAX
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee - 4.5 V. VOH - 5.5 V 0.1 0.1 mA
Vee = 4.5 V. IOL = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee - 4.5 V. IOL - 8 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee - 5.5 V. VI- 2.7V 20 20 ",A
IlL Vee - 5.5 V. VI = 0.4 V -0.1 -0.1 mA
leeH Vee = 5.5 V. VI = OV 0.22 0.4 0.22 0.4 mA
leeL Vee - 5.5 V. VI = 4.5 V 0.8 1.5 0.8 1.5 mA
tAli tYPical values are at Vee = 5 v, TA = 25°e

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 2 kQ.
PARAMETER UNIT
MIN MAX MIN MAX
tpLH Any Y 23 59 23 54 ns
NOTE 1: For load CirCUit and voltage waveforms, see page 1·12.
12:
2-48 TEXAS
INSTRUMENTS
TYPES SN54ALS27, SN54AS27, SN74ALS27, SN74AS27 .
TRIPLE 3·INPUT POSITIVE·NOR GATES
02661. APRIL 1982-REVISED DECEM8ER 1983

and Ceramic DIPs
and Reliability

(TOP VIEW)
NOR gates. They perform the Boolean functions
Y = A+B+CorY = A·B·Cinpositivelogic. 1A VCC.
The SN54ALS27 and SN54AS27 are characterized 1B 1C
for operation over the full military temperature range 2A 1Y
of - 55 °C to 125°C. The SN74ALS27 and 2B 3C
SN74AS27 are characterized for operation from 0 °C 2C 3B
to 70 o C. 2Y 3A
3Y
INPUTS OUTPUT
A B C y SN54ALS27. SN54AS27 ••• FH PACKAGE
H X X L SN74ALS27. SN74AS27 ••• FN PACKAGE
X H X L (TOP VIEW)
X X H L U
L L L H III <d:: U UU
.-.-z>.-
3 2 (IJ
2A 1Y
logic symbol
NC NC
~
2B 3C
::J
1A (1) ()
1B (2) NC
2C
NC
3B
a:
1C (13)
U
2A~ (IJ
2B
2C
(4)
(5)
«
3A (9) NC-No internal connection c
2!
3B
3C
(101
(111
«
(IJ
...I
«
TEXAS 2-49
INSTRUMENlS
POST OFFICE BOX 225012 • OALLAS, TEXAS 75265
TRIPLE 3-INPUT POSITIVE-NOR GATES
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............. 7 V
Operating free-air temperature range: SN54ALS27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto 70 0 e

SN54ALS27 SN74ALS27
UNIT
SN54ALS27 SN74ALS27
PARAMET~R TEST CONDITIONS UNIT
VIK Vee'" 4.5 V, II'" -18 mA -1.5 -1.5 V
VOH Vee'" 4.5 V to 5.5 V, 10H'" -0.4 mA Vee- 2 Vee- 2 V
Vee'" 4.5 V, 10L'" 4 mA 0.25 0.4 0.25 0.4
V
III
VOL
Vee'" 4.5 V, 10L'" 8 mA 0.35 0.5
II Vee'" 5.5 V, VI'" 7 V 0.1 0.1 mA
IIH Vee'" 5.5 V, VI'" 2.7V 20 20 Il A
):- IlL Vee'" 5.5 V, VI '" 0.4 V -0.1 -0.1 mA
r-
en 10*
leeH
Vee'"
Vee'"
5.5
5.5
V,
V,
Va '" 2.25 V
VI'" 0 V
-30
0.97
-112
1.8
-30
0.97
-112
1.8
mA
mA
):- leeL Vee'" 5.5 V, VI'" 4.5 V 2 4 2 4 mA
2 tAli typical values are at Vee = 5 V, TA = 25°e.
o *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
):-
VCC '" 4.5 V to 5.5 V,
Q CL'" 50 pF,
:::D FROM TO
o PARAMETER
(INPUT) (OUTPUT)
RL'" 500 Q,
UNIT
c SN54ALS27
TA '" MIN to MAX
SN74ALS27
=i MIN MAX MAX
en tpLH Any Y 4 22
MIN
4 15 ns
NOTE 1: For load Circuit and voltage waveforms, see page 1-1 2.
2-50 TEXAS
INSTRUMENlS
TRIPLE 3·INPUT POSITIVE·NOR GATES
Supply voltage. Vee ................................................................ 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AS27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °c to 70°C

SN54AS27 SN74AS27
UNIT
SN54AS27 SN74AS27
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V. 10H = -2 mA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V. 10L = 20 mA 0.35 0,5 0.35 0.5 V
II Vee - 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7V 20 20 IlA
IlL Vee = 5.5 V. VI = 0.4 V -0.5 -0.5 mA
10* Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
en
leeH Vee = 5.5 V. VI = OV 4 6.4 4 6.4 mA !:::
= 4.5 V ::>
leeL Vee - 5.5 V.
tAli typical valuas are at Vee = 5 V. TA = 25°e.
VI 10.6 17.1 10.6 17.1 mA
ua:
u
en
Vcc = 4.5 V to 5.5 V. <t
CL = 50 pF.
= 500Q.
c
PARAMETER
FROM
IINPUT)
TO
(OUTPUT)
RL
TA = MIN to MAX
UNIT z
SN54AS27 SN74AS27
<t
MIN MAX MIN MAX en
...J
tpLH Any Y 1 6.5 1 5.5 ns
tPHL Any Y 1 5 1 4.5 ns
<t
TEXAS 2-51
INSTRUMENlS
- l>
r-
en
l>
2
C
l>
en
Q
:Jl
(")
c:
=i
en
2-52
QUADRUPLE 2·INPUT POSITIVE·NOR BUFFERS

and Ceramic DIPs
and Reliability
description SN54ALS28A ••• J PACKAGE

SN74ALS28A ••• N PACKAGE
(TOP VIEW)
buffer gates. They perform the Boolean functions
Y = A+B or Y = A'S in positive logic. 1Y VCC
1A 4Y
The SN54ALS28A is characterized for operation 1B 4B
over the full military temperature range of - 55 DC to 2Y 4A
125 DC. The SN74ALS28A is characterized for 2A 3Y
operation from 0 DC to 70 DC. 2B 3B
3A
FUNCTION TA8LE
(each gate) SN54ALS28A ••• FH PACKAGE
INPUTS SN74ALS28A ••• FN PACKAGE

OUTPUT
A B Y (TOP VIEW)
H X L U
<{>-U U>-
X H L ...-...-Z>'<t
L L " H
1B 4B
logic symbol
NC NC en
2Y
NC
4A
NC
!::
1A ::J
18 2A 3Y (,)
2A
a::
28
(,)
3A en
38 NC-ND internal connection <C
4A c
48 2
<C"
en
..J
<C
TEXAS 2-53
INSfRUMENlS
POST OFF.ICE BOX 225012 • DALLAS. TEXAS 75265
QUADRUPLE 2-INPUT POSITIVE-NOR BUFFERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS28A . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS28A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCt070oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ~ ............. - 65°C to 1 50°C

UNIT
IOH High-level output current -1 -2.6 mA
PARAMETER TES.T CONDITIONS UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. IOH = -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
lEI VOL
Vee
Vee
Vee
= 4.5 V.
= 4.5 V.
= 4.5 V,
IOH = -2.6 mA
IOl = 12 mA
IOl = 24 mA
0.25 0.4
2.4 3.2
0.25
0.35
0.4
0.5
V
J> II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA

r- Vee = 5.5 V, VI = 2.7 V
en IIH
III Vee = 5.5 V, Vil = 0.4 V
20
-0.1
20
-0.1
/lA
mA
J> lo:t Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
2 leeH Vee = 5.5 V, VI - 0 V 1.7 "2.8 1.7 2.8 mA
C leel Vee = 5.5 V. VI = 4.5 V 5.6 9 5.6 9 mA
J>
en tAli typical values are at VCC = S V, TA = 2SoC.
:tThe output conditions hava been chosen to produce a current that closaly approximates ona half of the true short-circuit output current. lOS'
Q switching characteristics (see Note 1)

:D Vcc = 4.5 V to 5.5 V,
o CL = 50 pF.
c FROM TO RL = 500 Q,
=i PARAMETER
(lNPUn (OUTPUT) TA = MIN to MAX
UNIT
en SN54ALS28A SN74ALS28A
MIN MAX MIN MAX
tplH A or B Y 2 10 2 8 ns
tPHl Aor B Y 2 10 2 7 ns
NOTE 1: For load cirCUIt and voltage waveforms, see page 1-12.
2-54 TEXAS
INSTRUMENTS
8·INPUT POSITIVE·NAND GATES
D2661. APRIL 1982-REVISED DECEMBER 1983

and Ceramic DIPs
and Reliability
These devices contain a single a-input NAND gate
(TOP VIEW)
and perform the following Boolean functions in
positive logic: A VCC
Y = A·B·C·D·E-F-G·H OR B NC
C H
Y = A+B+C+D+E+F+G+H D G
The Sf',J54ALS30 and SN54AS30 are characterized E NC
for operation over the full military temperature range F NC
of - 55°C to 1 25°C. The SN74ALS30 and GND Y
SN74AS30 are characterized for operation from ooC
to 70°C.

FUNCTION TABLE
OUTPUT (TOP VIEW)
INPUTS A THRU H
V
U
All inputs H L U uu
co«Z>Z
One or more inputs L H
logic symbol
C H
(1) &
NC NC en
A
(2)
D G t::
B NC NC
::>
c
D
(3)
(4)
(8) y
E NC ua:
(5)
(6)
u..OU)-U
ZZ Z
U
l!l
en
G
(11)
(12)
NC-No internal connection «
H
c
Pin numbers shown are for J and N packages. z
«
en
-I
«
CoPyri9ht © 1982 by Texas Instruments Incorporated
TEXAS 2-55
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 150°C

SN54AlS30 SN74AlS30
UNIT
Vil Low-level input voltage 0.8 0.8 V
SN54AlS30 SN74AlS30
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA Vee- 2 Vee- 2 V
Vee = 4.5 V, 10L = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10L = 8 rnA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 Jl.A
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
10* Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
leeH Vee = 5.5 V, VI = 0 V 0.22 0.36 0.22 0.36 rnA
leel Vee = 5.5 V, VI = 4.5 V 0.54 0.9 0.54 0.9 rnA
tAli typical values are at Vee = 5V,TA = 25°C.
iThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
FROM TO RL = 500 Q,
PARAMETER UNIT
SN54AlS30 SN74AlS30
MIN MAX MIN MAX
tplH Any Y 3 12 3 10 ns
tpHl Any Y 5 22 5 20 ns
2-56 TEXAS
INSIRUMENTS
8-INPUT POSITIVE-NAND GATES
absolute maximum ratings over op'erating free-air temperature range (unless otherwise noted)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74AS30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; ...... - 65°C to 1 50°C

SN54AS30 SN74AS30
UNIT
SN54AS30 SN74AS30
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V, 10l = 20 rnA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7V 20 20 ,..A
= 5.5 V, VI = 0.4 V
III
10:1:
Vee
Vee = 5.5 V, Vo = 2.25 V -30
-0.5
-112 -30
-0.5
-112
rnA
rnA
en
leeH Vee = 5.5 V, VI = OV 0.9 1.5 0.9 1.5 rnA !=
leel Vee = 5.5 V, VI = 4.5 V 3 4.9 3 4.9 rnA
::l
tAli typical values are at Vee = 5 V, TA = 25°e.
U
;The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' a:
U
en
Vcc = 4.5 V to 5.5 V, <C
FROM TO
Cl = 50 pF,
Rl = 500 Q,
c
PARAMETER
UNIT
~~
SN54AS30 SN74AS30
MIN MAX MIN MAX en
....I
tplH Any Y 1 5.5 1 ns
tpHl Any Y 1 5 1
5
4.5 ns
<C
TEXAS 2-57
INSTRUMENTS
- >
r-
en
>
2
C
>
en
Q
:D
o
c:
=i
en
2-58
QUADRUPLE 2·INPUT POSITIVE·OR GATES

and Ceramic DIPs
and Reliability
description SN54ALS32. SN54AS32 .•. J PACKAGE

These devices contain four independent 2-input OR
(TOP VIEW)
gates. They perform the Boolean functions Y = A + B
or Y = Ii.. B in positive logic. 1A VCC
1B 4B
The SN54ALS32 and SN54AS32 are characterized
1Y 4A
2A 4Y
of - 55°C to 125°C. The SN74ALS32 and
2B 3B
SN74AS32 are characterized for operation from 0 °C
2Y 3A
to 70°C.
GND 3Y
FUNCTION TABLE
(each gate)
INPUTS OUTPUT SN54ALS32. SN54AS32 ••• FH PACKAGE

A B Y SN74ALS32. SN74AS32 ••• FN PACKAGE
(TOP VIEW)
H X H
X H H U
CD <x: U UCD
L L L z>v
logic symbol NC
4A
NC
en
2A 4Y !:::
lA
(11
;;'1 ::)
(3)lY NC NC
(2) ()
3B
18
(4) a:
2A
(6)2Y ()
(5)
28 >-OU>-<X:
3A
(9) NZZMM
t9
en
38
(10)
(0) 3Y
<C
(12) NC - No internal connection
4A C
48
(13)
(11)4Y
z
<C
en
~
<C
TEXAS 2-59
INSTRUMENTS .
absolute maximum ratings over operating froe·alr temperature range (unless otherwise noted)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
.Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : ................. - 65 °e to 1 50 °e

SN54ALS32 SN74ALS32
UNIT
electrical characteristics over recomme~ded operating free-air temperature range (unless otherwise noted)
SN54ALS32 SN74ALS32
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
-
VOH Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA Vee- 2 Vee- 2 V
Vee = 4.5 V, 10l = 4 rnA 0.25 0.4 0.25 0.4
Val V
Vee = 4.5 V, 10l = 8 rnA 0.35 0.5
II Vee - 5.5 V, VI - 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7V 20 20 iJ A
>
r-
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
en 10*
leeH
Vee
Vee
=
=
5.5 V,
5.5V,
Va = 2.25 V
VI = 4.5 V
-30
1.9
-112
4
-30
1.9
-112
4
rnA
rnA
>
2
leel Vee = 5.5 V,
t All typical values are et Vee = 5 V. TA = 25 ·C.
VI = 0 V 2.6 4.9 2.6 4.9 rnA
o *The output conditiOns have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
>
Vcc = 4.5 V to 5.5 V.
Q CL = 50 pF.
::c FROM TO RL = 500 Q.
o PARAMETER
(INPUT) (OUTPUT)
UNIT
c SN54ALS32
TA = MIN to MAX
SN74ALS32
=i
t/)
MIN MAX MIN MAX
tplH A or B V 3 16 3 14 ns
tpHl A or B V 3 13 3 12 ns
NOTE 1. For load CirCUit and voltage waveforms. see page 1-1 2.
1:
2-60 TEXAS
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74AS32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 0 e

SN54AS32 SN74AS32
UNIT
SN54AS32 SN74AS32
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
VOL Vee = 4.5 V. 10L = 20 mA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI=2.7V 20 20 IlA
IlL Vee - 5.5 V, VI = 0.4 V -0.5 -0.5 mA
10* Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI = 4.5 V 7.3 12 .7.3 12 mA
leeL Vee = 5.5 V, VI = 0 V 16.5 26.6 16.5 26.6 mA

Vcc = 4.5 V to 5.5 V,
CL = 50 pF.
FROM TO RL = 500 Q,
PARAMETER UNIT
/INPUT) (OUTPUT) TA = MIN to MAX
SN54AS32 SN74AS32
MIN MAX MIN MAX
tPLH A or B y 1 7.5 1 5.8 ns
tpHL A or B Y 1 6.5 1 5.8 ns
NOTE 1: For load circuit and voltage waveforms. see page 1-1 2.
TEXAS 2-61
INSTRUMENTS
POST OFFice BOX 225012 • DALLAS. TeXAS 75265
-.JI
l>
r-
o
l>
2
C
l>
o
~
::u
o
c:
=t
o
2-62

and Ceramic DIPs
e Dependable Texas Instruments Quality
and Reliability
SN54ALS33A .•• J PACKAGE
description SN74ALS33A ••• N PACKAGE
These devices contain four independent 2-input NOR (TOP VIEW)
buffer gates with open-collector outputs. Open- 1Y VCC
collector outputs require resistive pull-up to perform 1A 4Y
logically but can deliver higher VOH levels and are 1B 4B
commonly used in wired-AND applications. These 2Y 4A
devices perform the Boolean functions Y = A + B or 2A 3Y
Y = A' B in positive logic .. 2B 3B
The SN54ALS33A is characterized for operation GND 3A
over the full military temperature range of - 55 °C to
125°C. The SN74ALS33A is characterized for
operation from 0 °C to 70 o C. SN54ALS33A .•• FH PACKAGE
SN74ALS33A •.• FN PACKAGE
FUNCTION TABLE (each gate) (TOP VIEW)
u
INPUTS OUTPUT «>-uu>-
........ z>.;t
A B Y
H X L
X H L 4B
L L H NC
4A en
logic symbol NC !::
3Y ::J
U
lA
a:
lB U
2A en
2B
<C
3A C
3B 2
4A <C
4B en
-I
<C
TExAs 2-63
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . '........ ~ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , .. 7 V
. SN74ALS33A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C
. recommended operating conditions

. UNIT
-
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
VCC = 4.5 V, IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V, IOL = 24 rnA 0.35 0.5
II VCC = 5.5 V, VI = 7 V 0.1 0.1 rnA
»
r-
IIH VCC = 5.5 V,
= 5.5 V,
VI = 2.7V
VI = 0.4 V
20 20 /AA
en IlL
ICCH
Vee
VCC = 5.5 V, VI = OV 1.7
-0.1
2.8 1.7
-0.1
2.8
rnA
rnA
»
2
ICCl
tAli tYPical values are at Vee
VCC
=
= 5.5 V,
5 V, TA - 25°e
VI = 4.5 V 5.6 9 5.6 9 rnA
C
» switching characteristics (see Note 1)
en Vcc = 4.5 V to 5.5 V,
CL = 50 pF.
Q FROM TO RL = 680 Q.
::D PARAMETER
UNIT
(')
c SN54ALS33A
MIN MAX
SN74ALS33A
MIN MAX
=i
tJ) tPLH Aor B Y 10 40 10 33 ns
tpHL A or B Y 2 18 2 12 ns
2-64 TEXAS
INSTRUMENlS
HEX NON INVERTERS
02261. DECEMBER 1983
• Nonlnverters SN54ALS34, SN54AS34 ••• J PACKAGE

SN74ALS34, SN74AS34 .•• N PACKAGE
• Package Options Include Both Plastic and (TOP VIEW)
Ceramic Chip Carriers In Addition to Plastic
and Ceramic DIPs 1A Vee
1Y 6A
• I Dependable Texas Instruments Quality and
2A 6Y
Reliability
2Y 5A
3A 5Y
description
3Y 4A
These devices contain six independent noninverters. GND 4Y
They perform the Boolean functions Y = A.
The SN54ALS34 and SN54AS34 are characterized SN54ALS34, SN54AS34 ••• FH PACKAGE
fo'r operation over the full military temperature range SN74ALS34, SN74AS34 .•• FN PACKAGE
of - 55°C to 125°C. The SN74ALS34 and (TOP VIEW)
SN74AS34 are characterized for operation from 0 °e

to 70°C.
FUNCTION TABLE (each buffer) 2A 6Y

NC NC
INPUT OUTPUT
2Y 5A
A Y
NC NC
H H
3A 5Y
L L
logic symbol
lA
2A
3A
4A
SA
6A
TEXAS 2-65
INSTRUMENTS
HEX NONINVERTERS
absolute maximum ratings over operating free-air. temperature range (unless otherwise noted)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 DC
SN74ALS34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 DC to 70°C

SN54ALS34 SN74ALS34
UNIT
SN54AlS34 SN74ALS34
.. VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V

VOH Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V, IOl = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOl = 8 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 /lA
l> III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
r-
en lo~
leeH
Vee
Vee
= 5.5 V,
= 5.5 V,
Vo = 2.25 V
VI = 4.5 V
-30/
1
-112 -30
1
-112 mA
mA
l> leel Vee = 5.5 V, VI = 0 V 3.5 3.5 mA
2 valuas ara at Vee = 6 V, TA = 26°e.
C *tAliThetypical
output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
l>
Vcc = 4.5 V to 5.5 V,
~ CL = 50 pF,
::c FROM TO RL = 500 Q,
('") PARAMETER UNIT
TA = MIN to MAX
c: (INPUT) (OUTPUT)
SN54ALS34 SN74ALS34
=i MIN TYPt MAX MIN TYPt MAX
en tplH 8 8
A Y ns
tpHl 6 6
PRODUCT PREVIEW 1:
2-66
This page contain. Information on a product under
development. Tox•• Instruments reserves the right to TEXAS
change or discontinue this product without notice. INSTRUMENTS
HEX NONINVERTERS
Supply voltage, Vee .................................................... '.' ......... 7 V
Input voltage . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , ..... 7 V
Operating free-air temperature range: SN54AS34 ...•............................. - 55 °C to 125 °C
SN74AS34 ......•.............................. 0 °c to 70 °C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °C to 150 °C

SN54AS34 SN74AS34
UNIT
10H High-level output current -2, -2 rnA
SN54AS34 SN74AS34
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V. 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V, 10L = 20 rnA 0.35 0.5 0.35 0.5 V
I, Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, V, = 2.7V 20 20 /AA
Vee = 5.5 V. VI = 0.4 V
IlL
= 5.5 V, Vo = 2.25 V
-0.1 -0.1 rnA
en
10*
leeH
Vee
Vee = 5.5 V, VI = 4.5 V
-30
7.4
-112
12
-30
7.4
-112
12
rnA
rnA
t::
leeL Vee = 5.5 V, VI = OV 21.3 34.6 21.3 34.6 rnA
:::J
(.)
tAU typical values are at Vee = 5 V, TA = 25°e.
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS' a:
(.)
en
Vec = 4.5 V to 5.5 V, <t
CL = 50 pF,
FROM TO RL = 500 Q,
C
PARAMETER UNIT 2
TA = MIN to MAX
(INPUT) (OUTPUT)
SN54AS34 SN74AS34
<t
MIN MAX MIN MAX en
-'
tpLH
tpHL
A Y
1
1
6.5
7
1
1
5.5
6
ns <t
NOTE 1: For load circuit and voltage wavforms. see page 1-12.
TEXAS 2-67
INSTRUMENTS
2-68
HEX NONINVERTERS WITH OPEN·COLLECTOR OUTPUTS
• Noninverters with Open-Collector Outputs SN54ALS35 ••• J PACKAGE

SN74ALS35 ••• N PACKAGE
and Ceramic DIPs 1A VCC
1Y 6A
• Dependable Texas Instruments Quality and
2A 6Y
Reliability
2Y 5A
3A 5Y
description
3Y 4A
These devices contain six independent noninverters. GND 4Y
They perform the Boolean functions Y = A. The
open-collector outputs require pull-up resistors to
SN54ALS35 ••• FH PACKAGE
perform correctly. They may be connected to other SN74ALS35 ••• FN PACKAGE
open-collector outputs to implement active-low ITOPVIEW)
wired-OR or active-high wired-AND functions. Open-
U
collector devices are often used to generate higher >- « U U «
z > to
VOH levels.
1 20 HJ
The SN54ALS35 is characterized for operation over 6V
2A
the full military temperature range of - 55°C to NC
NC
125°C. The SN74ALS35 is characterized for opera- 5A
2Y
tion from 0 °C to 70°C. 7
NC NC
3A 8 5Y
FUNCTION TABLE leach buffer)
9 10 111213
INPUT OUTPUT >-ClU>-«

C'l z Z '<t '<t
V <.:)
A
H H NC- No internal connection
L L
logic symbol
1A
2A
3A
4A
SA
6A
3 PRODUCT PREVIEW Copyright © 1983 by Texas I~struments Incorporated

ThIs document contain. Infonnalion on • product under
development. Texas Instruments reserves the right to TEXAS 2-69
POST OFFICE BOX 225012" DALLAS, TEXAS 75265
HEX NONINVERTERS WITH OPEN·COLLECTOR OUTPUTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e

SN54AlS35 SN74AlS35
UNIT
SN54AlS35 SN74AlS35
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
IOH Vcc = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
~
Vcc = 4.5 V, 10l = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vcc = 4.5 V, 10l = 8 mA 0.35 0.5
II Vcc = 5.5 V, VI = 7 V 0.1 0.1 mA
>
r0-
IIH
III
Vcc
VCC
= 5.5 V.
= 5.5 V.
VI = 2.7V
VI = 0.4 V
20
-0.1
20
-0.1
Il A
mA
t/)
ICCH Vcc = 5.5 V, VI = 4.5 V 1 1 mA
>
Z
Icel Vcc = 5.5 V,
tAli typical values are at Vee = 6 V. TA = 26°e
VI = 0 V 3.5 3.5 mA
C
> switching characteristics (seo Note 1)
t/) Vcc = 4.5 V to 5.5 V,
Q FROM
Cl = 50 pF,
::c PARAMETER
(INPUT)
TO
(OUTPUT)
Rl = 680 Q,
TA = MIN to MAX
UNIT
(')
c: SN54AlS35
MIN TVPt MAX
SN74AlS35
MIN TVPt MAX
=i
t/) tplH A Y 25 25 ns
tpHl A Y 8 8 ns
tAli typical values ere at Vee = 6 V. TA = 26°e.
2-70 TEXAS
INSTRUMENTS
QUADRUPLE 2·INPUT POSITIVE·NAND BUFFERS

and Ceramic DIPs
and Reliability
description SN54ALS37A .•• J PACKAGE

SN74ALS37A ..• N PACKAGE
These devices contain four independent 2·input
(TOP VIEW)
NAND buffer gates. They perform the Boolean func-
tions Y = A' B or Y = A + B in positive logic. 1A Vee
The SN54ALS37 A is characterized for operation 1B 4B
over the full military temperature range of - 55 De to 1Y 4A
125 DC. The SN74ALS37 A is characterized for 2A 4Y
operation from 0 DC to 70 DC. 2B 3B
2Y 3A
GND 3Y
FUNCTION TABLE
(each gate)
SN54ALS37A ... FH PACKAGE
INPUTS OUTPUT
..
SN74ALS37A .•. FN PACKAGE
A B Y
(TOP VIEW)
H H L
L X H U
X L H
III « U U III
z>~
logic symbol 4A en
NC I-
1A
4Y ::>
Ne (J
1B
3B a::
2A
(J
2B
3A en
3B
~
4A
c
4B
2
~
en
-I
~
TEXAS 2-71
INSTRUMENTS
TYPES SN54ALS37 A.· SN74ALS3iA
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS37A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .- 65 °e to 1 50 °e

UNIT
VIK Vee = 4.5 V. II = -18 mA, -1.5 -1.5 V
VOH Vee = 4.5 V. IOH = -1 mA 2.4 3.3 V
-.J VOL
Vee = 4.5 V.
Vee = 4.5 V.
Vee = 4.5 V.
IOH = -2.6 mA
IOL = 12 mA
10l = 24 mA
0.25 0.4
2.4 3.2
0.25
0.35
0.4
0.5
V
»
r-
II
IIH
Vee
Vee
=
=
5.5 V.
5.5 V.
VI = 7 V
VI = 2.7 V
0.1
20
0.1 mA
20 IJA
CJ)
III Vee = 5.5 V. Vil = 0.4 V -0.1 -0.1 mA
»
2
loi
leeH
Vee =
5.5 V.
Vee = 5.'5 V.
Vo = 2.25 V
VI = 0 V
-30
0.86
-112
1.6
-30
0.86
-112
1.6
mA
mA
C leel Vee = 5.5 V. VI = 4.5 V 4.8 7.8 4.8 7.8 mA
»
CJ)
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
o switching characteristics (see Note 1)

::u VCC = 4.5 V to 5.5 V.
o CL = 50 pF.
c PARAMETER
FROM TO RL = 500 Q.
=i
CJ)
UNIT
MIN MAX MIN MAX
tplH A or 8 Y 2 10 2 8 ns
2-72 TEXAS
INSTRUMENTS
02661, APRIL 1982-REVISED DECEM8ER 1983
• Package Options Include Both Plastic and.

and Ceramic DIPs
and Reliability
SN54ALS38A ... J PACKAGE
description SN74ALS38A .•. N PACKAGE
ITOP VIEW)
These devices contain four independent 2-input
NAND buffer gates with open-collector outputs. 1A Vee
These NAND buffers perform the Boolean functions 18 48
Y = A' B or Y = A+ B in positive logiC. The open- 1Y 4A
collector outputs require pull-up resistors to perform 2A 4Y
correctly. They may be connected to other open- 28 38
collector outputs to implement active-low wired-OR 2Y 3A
or active-high wired-AND functions. Open-collector GND 3Y
devices are often used to generate higher VOH
levels.
The SN54ALS38A is characterized for operation SN54ALS38A •.. FH PACKAGE

over the full military temperature range of - 55°C to SN74ALS38A ••. FN PACKAGE
125°C. The SN74ALS38A is characterized for ITOP VIEW)
...
operation from 0 °C to 70°C. u
CD « uz>q-
u CD
FUNCTION TABLE leach gate)

1Y 4A
INPUTS OUTPUT NC NC
A B V 2A 4Y CI)
H H L NC NC
!::
L X H 3B ::>
X L H u
logic symbol a:
U
CI)
1A
18
<C
2A c
28
:2:
3A
<C
38
CI)
..oJ
4A
<C
48
Copyright © 1982 by Texas Instruments Incerporated
TEXAS 2-73
INSTRUMENTS
Supply voltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS38A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOet070 o e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 0 e

UNIT
VIH High-level input voltage ' 2 2 V
-
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
Vee = 4.5 V. IOl = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOl = 24 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
»
r-
IIH
III
Vee = 5.5 V.
Vee = 5.5 V.
VI = 2.7V
VI = 0.4 V
20
-0.1
20
-0.1
JJ.A
mA
VJ leeH Vee = 5.5 V. VI = OV 0.86 1.6 0.86 1.6 rnA
»
:2
leel
Vee = 5.5 V,
= 5 V. TA = 25°e
VI = 4.5 V 4.8 7.8 4.8 7.8 mA
C
» switching characteristics (see Note 1)
VJ Vcc = 4.5 V to 5.5 V.
~
CL = 50 pF.
FROM TO RL = 680 Q.
::0 PARAMETER UNIT
c SN54ALS38A
MIN MAX
SN74ALS38A
MIN MAX
=i tplH A or 8 Y 10 40 10 33 ns
VJ tpHl A or B Y 2 18 2 12 ns
NOTE 1: For load Circuit and voltage waveforms, see page 1-12.
1:;
2-74 TEXAS
INSTRUMENTS
DUAL 4·INPUT POSITIVE·NAND BUFFERS
02661. APRIL 1982 -REVISED DECEMBER 198:>

and Ceramic DIPs
and Reliability
description SN54ALS40A ••. J PACKAGE

SN74ALS40A ••. N PACKAGE
(TOP VIEW)
NAND buffer gates. They perform the Boolean func-
tions Y = A'B'C'D or Y = A+B+C+D in positive
1A VCC
logic.
1B 20
The SN54ALS40A is characterized for operation NC 2C
over the full military temperature range of - 55 DC to 1C NC
1 25 DC. The SN74ALS40A is characterized for 10 2B
operation from 0 DC to 70 DC. 1Y 2A
GND 2Y

SN54ALS40A ••. FH PACKAGE
INPUTS OUTPUT SN74ALS40A ••. FN PACKAGE
A B C D Y (TOP VIEW)
H H H H L
u
L X X X H co<t:uuo
",-Z>N
X L X X H
X X L X H 3 2 1 2019
X X X L H NC 4
NC 5
1C 6
logic symbol NC 7
1D 8
(1)
lA &[> 9 10 11 1213
(2)
lB >-ou>-<t:
(4) lV ZZNN
lC l?
(5)
10 NC - No internal connection
(9)
2A
(10)
2B
(12) 2V
2C
(13)
20
TEXAS 2-75
INSTRUMENTS
DUAL 4-INPUT POSITIVE-NAND BUFFERS
Supply voltage, Vee ................................................... .- ........... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS40A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 0 e

UNIT
10H High-level output current -1 -2.6 mA
VIK Vce = 4.5 V, II = -18 mA -1.5 -1.5 V
Vce = 4.5 V to 5.5 V, 10H = -0.4 mA Vec- 2 Vec- 2
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
1m Val
Vec
Vec
Vec
=
=
=
4:5 V,
4.5 V,
4.5 V,
10H = -2.6 mA
10L = 12 mA
10l = 24 mA
0.25 0.4
2.4 3.2
0.25
0.35
0.4
0.5
V
:t- II Vce = 5.5 V, VI = 7 V 0.1 0.1 mA

r- IIH Vce = 5.5 V, VI = 2.7V 20 20 /-fA
t/)
III Vee = 5.5 V, Vil = 0.4 V -0.1 -0.1 mA
:t- lot Vec =' 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
2 lecH Vcc = 5.5 V, VI = OV 0.43 0.8 0.43 0.8 mA
C lecl Vce = 5.5 V, VI = 4.5 V 2.4 3.9 2.4 3.9 mA
:t-
t/)
t All typical values are at V CC = 5 V, T A = 25°C.
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS'

:IJ Vce = 4.5 V to 5.5 V,
o
c FROM TO
CL = 50 pF.
RL = 500 Q,
=i
t/)
PARAMETER
UNIT
MIN MAX MIN MAX
tplH AorB y 2 10 2 8 ns
tpHl A or B y 2 10 2 7 ns
121
2-76 TEXAS
INSTRUMENTS
DUAL D·TYPE POSITIVE·EDGE·TRIGGERED
FLlP·FLOPS WITH CLEAR AND PRESET
D2661, APRIL 1982 - REVISED DECEMBER 1983
• Package Options Include Both Plastic and Ceramic SN54ALS74, SN54AS74 ..• J PACKAGE
Chip Carriers in Addition to Plastic and Ceramic DIPs SN74ALS74, SN74AS74 .•. N PACKAGE
(TOP VIEW)
• Dependable Texas Instruments Quality and Reliability
1CLR VCC
TYPICAL MAXIMUM TYPICAL POWER 10 2CLR
TYPE CLOCK FREQUENCY DISSIPATION 1CLK 20
(CL = 50 pF) PER FLIP-FLOP 1PRE 2CLK
10 2PRE
'ALS74 50 MHz 6mW 10 20
'AS74 134 MHz 26 mW
GNO """'-_ _----'- 20
description
SN54ALS74, SN54AS74 . . FH PACKAGE
These devices contain two independent Ootype positive-edge- SN74ALS74, SN74AS74 . . FN PACKAGE
triggered flip-flops. A low level at the Preset or Clear inputs sets (TOP VIEW)
or resets the outputs regardless of the levels of the other inputs.
When Preset and Clear are inactive (high), data at the 0 input e: ule:
o I....d Z>N
u ud
meeting the setup time requirements are transferred to the out-
puts on the positive-going edge of the clock pulse. Clock trigger-
ing occurs at a voltage level and is not directly related to the rise
1CLK 20
time of the clock pulse. Following the hold time interval, data at
NC NC
..
the 0 input may be changed without affecting the levels at the
1 PRE 2CLK
outputs.
NC NC
The SN54ALS74 and SN54AS74 are characterized for opera- 10 2PRE
tion over the full military temperature range of - 55°C to 9 10 111213
125°C. The SN74ALS74 and SN74AS74 are characterized for Id 0 u 10 0
operation from ooC to 70°C. .... ZZNN
(!)
en
NC - No internal connection t:::
FUNCTION T~BLE ::J
logic symbol U
INPUTS OUTPUTS
a:
. PRESET CLEAR CLOCK D Q Q U
L H X X H L en
H
L
L
L
X
X
X
X
L
H*
H
H* 1D
10
«
H H t H H L 1CLR C
2PRE 2
H
H
H
H L
t L
X
L
00
H
00
.2CLK
2D
20
«
"The output levels in this configuration are not guaranteed to meet the 2CLR 20 en
..J
minimum levels for VOH if the lows at Preset and Clear are near VIL max-
imum. Furthermore, this configuration is nonstable; that is, it will not persist
when either Preset or Clear returns to its inactive (hig h) level.
«
Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS74, SN54AS74 . . . . . . . . . . . . . . . . . . . . . - 55°C to 125 °C
SN74ALS74, SN74AS74 . . . . . . . . . '. . . . . . . . . . . . . . . . 0 °C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 DC to 1 50°C
Copyright © 1982 by Texas Instruments Incorporated.

13
TEXAS 2-77
INSTRUMENTS
DUAL D·TYPE POSITIVE·EDGE·TRIGGERED
FLlp·FLOPS WITH CLEAR AND PRESET

SN54AlS74 SN74AlS74
UNIT
MIN NOM MAX MIN NOM MAX,
VCC Supply voltage ·4.5 5 5.5 4.5 5 5.5 V
fclock Clock frequency 0 30 0 34 MHz
"-
PRE or ClR low 15 15
tw Pulse duration ClK high 16.5 14.5 ns
ClK low 16.5 14.5
Setup time Data 15 15
tsu ns
before ClKI PRE or ClR inactive 10 10
th Hold time, data after ClK I 0 0 ns
TA Operating free-air temperature -55 125 0 70 °c
SN54AlS74 SN74AlS74
Typt Typt MAX
..
MIN MAX MIN
VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH VCC = 4.5 V to 5.5 V, 10H = -0.4 mA VCC-2 VCC-2 V
VCC = 4.5 V, 10l = 4 mA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V, 10l = 8 mA 0.35 0.5
ClK or D 0.1 0.1
II
PRE or ClR
VCC = 5.5 V, VI = 7 V mA
0.2 0.2
l>
r- IIH
ClK or D
VCC = 5.5 V. VI = 2.7 V
20 20
en PRE or ClR 40 40
/loA
ClK or D -0.2 -0.2

l> III
PRE or ClR
VCC = 5.5 V. VI = 0.4 V
-0.4 -0.4
mA
2 10:1: VCC = 5.5 V. Vo = 2.25 V -10 -60 -10 -60 mA
C ICC VCC = 5.5 V. See Note 1 2.4 4 2.4 4 mA
l>
en tAli typical values are at VCC .= 5 V. TA ,,; 25°C
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
Q NOTE 1: ICC is measured with J, K, ClK, and PRE grounded. then with J, K. ClK, and CI:R grounded.
::0
o switching characteristics (see Note 2)
c: Vcc = 4.5 V to 5.5 V.
=i Cl = 50 pF.
en PARAMETER
FROM TO RL = 500 n.
UNIT
SN54AlS74 SN74AlS74
MIN MAX MIN MAX
f max 30 34 MHz
tplH 3 15 3 13
PRE or ClR QorQ ns
tpHl 5 17 5 15
tplH '5 18 5 16
ClK QorO ns
tpHl 7 20 7 18
2-78 TEXAS
INSTRUMENTS
DUAL O·TYPE POSITIVE·EOGE·TRIGGEREO

SN54AS74 SN74AS74
UNIT
10L low-level output current 20 20 mA
PRE or CLR low 4 4
tw Pulse duration ClK high 4 4 ns
ClK low 5.5 5.5
Setup time Data 4.5 . 4.5
tsu ns
before ClKI PRE or ClR inactive, 2 2
th Hold time. data after ClKI 0 0 ns
SN54AS74 SN74AS74
MIN Typt MAX MIN Typt MAX
VIK VCC = 4.5 V. II = -18 mA -1.2 -1.2 V
VOH VCC ,; 4.5 V to 5.5 V. 10H = -2 mA VCC-2 VCC-2 V
VOL VCC = 4.5 V. 10l = 20 mA 0.25 0.5 0.25 0.5 V
II VCC = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH VCC = 5.5 V. VI = 2.7 V 20 20 /lA
I ClK or D VI = 0.4 V
-0.5 -0.5
mA
III VCC = 5.5 V.
I PRE or ClR -1.5 -1.5
en
10:1:
ICC
VCC = 5.5 V.
VCC = 5.5 V.
VO= 2.25 V
See Note 1
-30
10.5
-112
16
-30
10.5 ~
-112
16
mA
mA
t=
::::>
tAli typical values are at VCC = 5 V. TA = 25°C. u
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS' a:
NOTE 1: ICC is measured with D. ClK. and PRE grounded. then with D. ClK. and ClR grounded. u
switching characteristics (see Note 2) en
Vcc= 4.5, V to 5.5 V.
<t
Cl = 50 pF. c
FROM: TO Rl = 500 n. 2
PARAMETER
UNIT
<t
MIN
SN54AS74
MAX MIN
SN74AS74
MAX
en
-J
f max 90 105 MHz <t
tpLH 3 8.5 3 7.5
PRE or ClR Qor 0: ns
tpHL 3.5 11.5 3.5 10.5
tPlH 3.5 9 3.5 8
ClK QorO ns
tpHL 4.5 10.5 4.5 9
:3
TEXAS 2-79
INSTRUMENTS
- »
r-
tn
»
z
c
»
tn
Q
II
(")
c
=i
tn
2-80
QUADRUPLE 2·INPUT EXCLUSIVE·OR GATES
o Package Options Include Both Plastic and Ceramic SN54ALS86 ••• J PACKAGE
Chip Carriers in Addition to Plastic and Ceramic DIPs SN74ALS86 ... N PACKAGE
(TOP VIEW)
o Dependable Texas Instruments Quality and Reliability
1A VCC
1B 4B
description 1Y 4A
2A 4Y
These devices contain four independent 2-input Exclusive-OR
2B 3B
Y = A eB = AB+AB in positive logic.
2Y
GND
3A
3Y
A common application is as a true/complement element. If one of
the inputs is low, the other input will be reproduced in true form SN54ALS86 ... FH PACKAGE
at the output. If one of the inputs is high, the signal on the other SN74ALS86 ... FN PACKAGE
input will be reproduced inverted at the output. (TOP VIEW)
The SN54ALS86 is characterized for operation over the full U
military temperature range of - 55 °C to 125°C. The ID«UUID
.-z><t
SN74ALS86 is characterized for operation from ooC to 70°C.
1Y 4A
NC NC
2A 4Y
logic symbol NC NC
2B 3B
FUNCTION TABLE
1A (each gate)
1Y
1B
INPUTS OUTPUT
2A
2Y A B Y
28 tJ)
L L L NC-No internal connection
3A
3Y
L H H I-
38
4A H L H ::>
4B H H L (.)
a::
(.)
tJ)
exclusive-OR logic «
An exclusive-OR gate has many applications, some of which can be represented better by alternative logic symbols. c
2!
EXCLUSIVE-OR «
tJ)
..J
«
These are five equivalent Exclusive-OR symbols valid for an 'ALS86 gate in positive logic; negation may be shown at any
two ports.
LOGIC IDENTITY ELEMENT EVEN-PARITY ODD-PARITY ELEMENT
The output is active (low) if The output is active (low) if The output is active (high) if
all inputs stand at the same an even number of inputs an odd number of inputs (i.e.,
logic level (Le., A = B). (i.e., 0 or 2) are active. only 1 of the 2) are active.

PRODUCT PREVIEW
83
This document contains information
on a product under development. Texas TEXAS 2-81
Instruments reserves the right to change or INSTRUMENTS
discontinue this product without notice. POST OFFICE BOX 225012 • DALLAS. TEXAS 75265
QUADRUPLE 2-INPUT EXCLUSIVE-OR GATES
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00et0700e
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e

SN54ALS86 SN74ALS86
UNIT
IOL Low·level output current 4 8 rnA
TA Operating free·air temperature - 55 125 0 70 De
electrica~ characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54ALS86 SN74ALS86
-
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
VOH Vee - 4.5 V to 5.5 V, IOH - -0.4 rnA vee- 2 Vee- 2 V
Vee = 4.5 V, IOL = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 8 rnA 0.35 0.5
II Vee = 5.5 V. VI = 7V 0.1 0.1 rnA
»
r-
IIH
IlL
Vee = 5.5 V, VI = 2.7 V
VI = 0.4 V
20 20 p.A
= 5.5 V. 0-0.1 -0.1 rnA
en loi
Vee
Vee = 5.5 V. Va = 2.25 V -30 -112 -30 -112 rnA
»
2
lee Vee = 5.5 V. All inputs at 0 V 3 3 rnA
t All typical values are at Vee = 5 V. TA = 25 De.

C tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
»
o Vcc = 4.5 V to 5.5 V.

= 50 pF,
::c CL
o PARAMETER
FROM TO RL = 500 {l,
UNIT
c (lNPUTI (OUTPUT) TA = MIN to MAX
=i SN54ALS86
MIN Typt
SN74ALS86
MIN Typt
en tpLH A or B
MAX
7
MAX
7
Y ns
tpHL (other input low) 6 6
tpLH A or B 8 8
Y ns
tpHL (other input high) 7 7
t All typical values are at Vee = 5 v. TA = 25 De.

NOTE1: For load circuit and voltage waveforms. see page 1-12.
Additional information on these products can be obtained from the factory as it becomes available.
12
2-82 TEXAS
INSTRUMENTS
TYPES SN54AS95. SN74AS95
4·81T PARALLEL·ACCESS SHIFT REGISTER
D2661. DECEMBER 1983
• Serial·to·Parallel Conversions SN54AS95 ... J PACKAGE

SN74AS95 ... N PACKAGE
• Parallel Synchronous Loading
(TOP VIEW)
o Right or Left Shifts
SER IN VCC
o Package Options Include Both Plastic and A GA
Ceramic Chip Carriers in Addition to Plastic and B GB
Ceramic DIPs C GC
D GD
MODE ClK 2
Reliability
GND ClK 1
description
These four-bit registers feature parallel and serial SN54AS95 ... FH PACKAGE
inputs, parallel outputs, mode control, and two clock SN74AS95 ... FN PACKAGE
inputs. The registers have three modes of operation: (TOP VIEW)
Parallel (broadside) load ~

a: u
Shift right (the direction GA toward GD) w U u<!
Shift left (the direction GD toward GA)
<! (J) z >0
2
Parallel loading is accomplished by applying the four
bits and taking the mode control input high. The data B GB
is loaded into the associated flip-flops and appears at NC NC
the outputs after the high-to-Iow transition of the C Gc
Clock-2 input. During loading, the entry of serial data NC NC
is inhibited. D GD
9 10 11 1213
Shift right is accomplished on the high-to-Iow
transition of Clock 1 when the mode control is low; w 0 U N
shift left is accomplished on the high-to-Iow transition 0

0 Z
(!)
Z ~
...J
U
~
...J
U
en
of Clock 2 when the mode control is high by
~ !::
connecting the output of each flip-flop to the parallel :::>
input of the previous flip-flop (GD to input C, etc.);
NC- No internal connection
u
and serial data is entered at input D. The clock input
a:
may be applied commonly to Clock 1 and Clock 2 if u
both modes can be clocked from the same source. en
Changes at the mode control input should normally
be made while both clock inputs are low. However,
<t
conditions described in the last three lines of the c
function table will also ensure that the register 2
contents are protected. <t
CJ)
The SN54AS95 is characterized for operation over the -I
full military temperature range of - 55 °C to 125°C. <t
The SN74AS95 is characterized for operation from
ooC to 70°C.
83 PRODUCT PREVIEW Copyright © 1983 by Texas Instruments Incorporated
This document contain. infonnatlon on 8 product under

development. Texaalnstruments reserve, the right to TEXI\S 2-83
change or discontinue thl. product without notice. INSTRUMENTS
FUNCTION TABLE
INPUTS OUTPUTS
MODE CLOCKS PARALLEL
SERIAL QA QS QC QD
CONTROL 2 (L) 1 (R) A B C D
H H X X X X X X QAO QBO QCO aDO
H ~ X X a b c d a b c d
H ~ X X QBt Qct QDt d QBn QCn QDn d
L L H X X X X X QAO QBO QCO aDO
L X I H X X X X H QAn QBn °Cn
L X I L X X x' X L QAn QBn oCn
t L L X X X X X QAO QBO QCO QDO
~ L L X X X X X QAO QBO QCO aDO
~ L H X X X X X QAO QBO QCO aDO
t H L X X X X X QAO QBO QCO aDO
t H H X X X X X QAO QBO QCO QDO
tShilting left requires external connection of OB to A, Oc to B, and 0D to C. Serial data is entered at input D.
H = high level (steady state), L = low level (steady state), X = irrelevant (any input, including transitions).
~ = transition from high to low level, t = transition from low to high level.
a, b, c, d = the level of steady-state input at inputs A, B, C, or D, respectively.
OAO' 0BO, 0CO' 0DO = the level of 0A' 0B, 0C' or 0D, respectively, before the indicated steady-state input conditions were established.
OAn' OBn' OCn' ODn = the level of OA, OS, 0C. or 0D. respectively, before the most-recent ~ transition of the clock.
logic symbol
-
MODE
ClKl
ClK2
l> SER
r- A
(2)
CJ) 40
(3) (12)
B 40
l> c
(4) (11) °B
2 0
(5) (10) Oc
00
C
l> logic diagram (positive logic)
CJ) ~ ________________ ______________
DATA INPUTS -JA~ ~~
~
:::XJ MODE (6) [6)
(') CONTROL
C SERIAL (1) [1)
=i
CJ)
INPUT.
CLOCK 1 (9) [7)

RIGHT SHIFT
CLOCK 2 (8) [8)
LEFT SHIFT
(10) [9)
0A 0B 0c aD,
~--------------~v~--------------~
OUTPUTS
121
2-84 TEXAS
INSTRUMENTS
Supply voltage, Vee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage .............................................................. 7 V
Operating free-air temperature range: SN54AS95 ........................ - 55°C to 125°C
SN74AS95 ' ............................ DoC to 70°C
Storage temperature range ......................................... - 65°C to 1 50°C

SN54AS95 SN74AS95
UNIT
fclock Clock frequency 0 0 MHz
tw Pulse duration, ClK high or low ns
tsu Setup time, data before ClK + ns
Data
th Hold time after ClK + Mode (see Figure 1)
ns
Clock enable time ClK 1

ns
(see Figure 1) ClK 2 0 0
Clock inhibit time ClK 1
ns
(see Figure 1) ClK 2 0 0
SN54AS95 SN74AS95
VIK VCC = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V, 10H = -2mA VCC- 2 VCC-2 V
VOL VCC = 4.5 V, 10l = 20 mA 0.35 0.5 0.35 0.5 V
II VCC = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH VCC = 5.5 V, VI = 2.7 V 20 20 p.A
III VCC = 5.5 V, Vil = 0.4 V -0.5 -0.5 mA
10+ VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
ICCH VCC = 5.5 V mA
ICCl VCC = 5.5 V 26.1 26.1 mA
t All typical values are at Vee =

5 v, T A' = 25°C.
~The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS'
13
TEXAS 2-85
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
PARAMETER
FROM TO RL = 500 n,
UNIT
SN54AS95 SN74AS95
f max MHz
tPlH 6.4 6.4
elK Q ns
tpHl 7.1 7.1
t All typical values are at vee = 5 V, T A = 25°C.

NOTE1: For load circuit and voltage waveforms, see page 1·12.
Additional Information on these produces can be obtained from the factory as It becomes available.
SE,RIAL
INPUT
--.I \.-- -
.
- - - - - - VIH
VIL
..
MODE
CONTROL - - - - - " I _-----VIH
INPUT
1"-_ _ _ _ _.1_ - ---,-- VIL
VIH
CLOCK
INPUT1 _ _ _ _J
l>
r- " ' - - - - - - - - - - - VIL
en ~---1*_tenable 2
l> CLOCK 2 _ _ _ _ _ _ _ _ _ _ _'1

z INPUT
c
l>
en QA
OUTPUT
____________ -"J \'-----"/
Q VOLTAGE WAVEFORMS
::D
o NOTES: A. Input A is at a low level.
c: B. VIH = 3.5 V, VIL = 0.3 V.
=i
en FIGURE 1-CLOCK ENABLE, INHIBIT, AND HOLD TIMES
1~
2-86 TEXAS
INSTRUMENTS
DUAL J·R POSITlVE·EDGE·TRIGGERED
FLlP·FLOPS WITH CLEAR AND PRESET
• Package Options Include Both Plastic and Ceramic SN54ALS109,SN54AS109. J PACKAGE

Chip Carriers in Addition to Plastic and Ceramic DIPs SN74ALS109,SN74AS109 . N PACKAGE
(TOP VIEW)
1CLR VCC
1J 2CLR
TYPICAL POWER
TYPICAL MAXIMUM DISSIPATION
li< 2J
TYPE 1CLK 21<
CLOCK FREQUENCY PER FLIP-FLOP
'ALS109 50 MHz 6mW
'AS109 129 MHz 29 mW
1Q 20
GND
description
These devices contain two independent J-K positive-edge-
triggered flip-flops. A low level at the Preset or Clear inputs sets
SN54ALS109, SN54AS109 . FHPACKAGE
SN74ALS109,SN74AS109. FNPACKAGE
When Preset and Clear are inactive (high), data at the J and K
(TOP VIEW)
inputs meeting the setup time requirements are transferred to the
outputs on the positive-going edge of the clock pulse. Clock
triggering occurs at a voltage level and is not directly related to Ie:
..,OU U-l u~
the rise time of the clock pulse. Following the hold time interval, .- .- Z >'N
data at the J and K inputs may be changed without affecting the
levels at the outputs. These versatile flip-flops can perform as
toggle flip-flops by grounding K and tying J high. They also can
'-R
1CLK 21<
perform as D-type flip-flops if J and K are tied together.
NC
The SN54ALS109 and SN54AS109 are characterized for 1PRE
10 2PRE
operation over the full military temperature range of - 55 °C to
125 °C. The SN74ALS1 09 and SN74AS1 09 are characterized
en
for operation from 0 °C to 70°C. 100 UIO 0
!::
.-ZZNN ::>
FUNCTION TABLE
(!)
U
(EACH FLlP·FLOP) NC - No Internal connection a:
INPUTS OUTPUTS logic symbol U
PRESET CLEAR CLOCK J K a a en
H
L H
L
X
X
X
X
X
X
H
L
L
H
10
«
L L X X X H* H*
C
io Z
H
H
H
H
t
t
L
H L
L L
TOGGLE
H
«
H H t L H 00 00 en
-I
H
H
H
H
t
L
H
X
H
X
H
00
L
00 «
• The output levels in this configuration are not guaranteed to meet the
minimum levels for VOH if the lows at Preset and Clear are near VIL
maximum. Furthermore, this configuration is nonstable: that is, it will not Pin numbers shown are for J and N packages.
persist when Preset or Clear; returns to their inactive (high) level.
Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-~ir temperature range: SN54ALS1 09, SN54AS1 09 . . . . . . . . . . . . . . . . . . . . - 55 °C to 125 °C
SN74ALS109,SN74AS109 .... ~ . . . . . . . . . . . . . . . . . . . O°C~70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °C to 150 °c

33
TEXAS 2-87
INSTRUMENTS
DUAL J.i{ POSITIVE·EDGE·TRIGGERED

SN54AlS109 SN74AlS109
UNIT
tw Pulse duration ClK high 16.5 14.5 ns
ClK low 16.5 14.5
tsu ns
VIK Vce = 4.5 V, II = -18 mA -1.5 -1.5 V
-
VOH VCC = 4.5 V to 5.5 V, IOH = ",0.4 mA VCC-2 VCC-2 V
VCC = 4.5 V, IOl = 4 mA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V IOl = 8 mA 0.35 0.5
ClK, J, or K 0.1 0.1
II VCC = 5.5 V. VI = 7 V mA
PRE or ClR 0.2 0.2
l> ClK, J, or K 20 20
r- IIH
PRE or ClR
VCC = 5.5 V, . VI = 2.7 V
40 40
I'A
C/)
ClK, J or K -0.2 -0.2
VCC = 5.5 V, VI = 0.4 V mA
l> III
PRE or ClR -0.4 -0.4
2 IO:t VCC = 5.5 V, Vo = 2.25 V -10 -60 -10 -60 mA
C ICC VCC = 5.5 V, See Note 1 2.4 4 2.4 4 mA
l> tAli typical values are at VCC = 5 V, TA = 25°C.

C/) *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
C") NOTE 1: ICC is measured with J. K. ClK. and PRE grounded; then with K, K. ClK, and ClR grounded.
5;
C") switching characteristics (see Note 2)
c: Vcc = 4.5 V to 5.5 V,
=f Cl = 50 pF.
fA
PARAMETER
FROM TO Rl = 500 n. UNIT
MIN MAX MIN MAX
f max 30 34 MHz
tplH 3 15 3 13
PRE or ClR QorO ns
tpHl 5 17 5 15
tplH 5 18 5 16
ClK QorO ns
tPHl 7 20 7 18
121
2-88 TEXAS
INSTRUMENTS
DUAL J.i{ POSITIVE·EDGE·TRIGGERED
recommended operati~g conditions

SNS4AS109 SN74AS109
UNIT
fctock Clock frequency 0 90 0 105 MHz
PRE or ClR low 4 4
tw Pulse duration ClK high 4 4 ns
ClK low 5.5 5.5
Setup time Data 5.5 5.5
tsu ns
TA Operating free-air temperature -S5 125 0 70 °c
electrical characteristics over recommended operating free-air temperature range (unless otherwise notedl
SNS4AS109 SN74AS109
VIK Vec = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V, 10H = -2 mmA VCC-2 VCC-2 V
VOL Vec = 4.S V, IOl = 20 mA 0.25 0.5 0.25 0.5 V
II VCC = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vec = 5.5 V, VI = 2.7 V 20 20 /LA
III
LelK or D
Vec = 5.5 V, VI = 0.4 V
-O.S -0.5
mA en
IPRE or ClR -1.5 -1.5
!:::
10:1: Vec = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
:::>
ICC VCC ~ 5.5 V, See Note 1 11.5 17 11.5 17 mA
ua:
t All typical values are at VCC = 5 V. TA = 25°C.
~The output conditions have been chosen to produce a current that closely approximates one half of the true short· circuit output current. lOS' C3
NOTE 1: ICC is measured with D. ClK. and PRE grounded. then with D. ClK. and ClR grounded.
en
<t
switching characteristics (see Note 2l C
Vcc = 4.S V to S.S V.
Z
Cl = SO pF. <t
PARAMETER
FROM TO Rl = SOO n.
UNIT
en
(INPUT) (OUTPUT) TA = MIN to MAX ..J
SNS4AS109 SN74AS109 <t
MIN MAX MIN MAX
f max 90 105 MHz
tPlH 3 9 3 8
PRE or ClR QorO ns
tpHl 3.5 11.5 3.5 10.5
tPlH 3.5 10 3.5 9
ClK Qoro. ns
tpHl 4.5 10.5 4.5 9
Z83
TEXAS 2-89
INSTRUMENTS
..
»
r-
en
»
2
C
»
en
(')
::IJ
(')
c
=i
en
2-90
DUAL J·K NEGATlVE·EDGE·TRIGGERED FLlp·FLOPS
WITH CLEAR AND PRESET
02661. APRIL 1982 - REVISED DECEMBER 1983
• Fully Buffered to Offer Maximum Isolation from SN54ALS112A, SN54AS112 • J PACKAGE

External Disturbance SN74ALS112A. SN74AS112 . N PACKAGE
ITOP VIEW)
• Package Options Include Both Plastic and Ceramic
Carriers in Addition to Plastic and Ceramic DIPs.
1CLK Vce
• Dependable Texas Instruments Quality and Reliability 1K 1 eLR
1J 2CLR
1PRE 2CLK
TYPICAL POWER
TYPICAL MAXIMUM 10 2K
TYPE DISSIPATION
CLOCK FREQUENCY
PER FLIP-FLOP
15 2J
'ALS112A 50 MHz 6mW
20 2 PRE
'AS112 175 MHz 95 mW GND"--i,;;~......;;;.t-'20
description SN54ALS112A, SN54AS112 FH PACKAGE

These devices contain two independent J-K negative-edge- SN74ALS112A. SN74AS112 FN PACKAGE
triggered flip-flops. A low level at the Preset or Clear inputs sets (TOP VIEW)
When Preset and Clear are inactive (high). data at the J and K
inputs meeting the setup time requirements are transferred to the
~·u
:J u uu
.-Z>'-
ul5
outputs on the negative-going edge of the clock pulse. Clock
triggering occurs at a voltage level and is not directly related to
the rise time of the clock pulse. Following the hold time interval, 1J 2CLR
data at the J and K inputs may be changed without affecting the 1PRE 2CLK
levels at the outputs. These versatile flip-flops can perform as NC NC
toggle flip-flops by tying J and K high. 10 2K
The' SN 54ALS 112A and SN 54AS 112 are characterized for 16 2J
operation over the full military temperature range of - 55 DC to
125°C. The SN74ALS 112A and SN74AS 112 are characterized 100 u 0l~
for operation from ooC to 70°C. NZZNa..
N
en
<.!)
!::
FUNCTION TABLE NC - No internal connection ::l
INPUTS OUTPUTS (.)
PRE CLR CLK J K Q Q logic symbol a:
L H X X X H L (.)
H L X X X L H 1 PRE
en
L
H
L
H
X
I
X
L
X
L
H*
QO
H*
00
1J
1CLK
10
.«
H
H
H
H
I
I
H
L
L
H
H
L
L
H
10 c
2!
H
H
H
H
I
H
H
X
H
X
TOGGLE
00 00 2J 20
«
2CLK en
"The output levels in this configuration are not guaranteed to meet the minimum levels -I
for VOH if the lows at Preset and Clear are near VIL maximum. Furthermore. this
configuration is nonstable; that is. it will not persist when either Preset or Clear returns
2K
2CLR «
to its inactive (high) level. Pin numbers shown are for J and N packages.
Supply voltage. VCC ................................................................ 7 V
Input voltage .................................................................... " 7 V
Operating free-air temperature range:SN54ALS 112A, SN54AS112 . . . . . . . . . . . . . . . . . . .. - 55°e to 125°C
SN74ALS112A. SN74AS112 . . . . . . . . . . . . . . . . . . . . ... O°C to 70°C
Storage temperature range
Copyright © 1982 by ,Texas Instruments Incorporated

~83
TEXAS 2-91
INSTRUMENlS
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS
WITH CLEAR AND PRESET

UNIT
tw Pulse duration ClK high 20 16.5 ns
ClK low 20 16.5
tsu ns
th Hold time, data after ClKI 0 0 ns
TA Operating free-air temperature - 55 125 0 70 °c
SN54AlS112A SN74ALS 112A
VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH VCC = 4.5 V to 5.5 V, IOH = - 0.4 rnA VCC-2 VCC-2 V
VCC = 4.5 V, IOl =4 mA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V IOl =8 mA 0.35 0.5
J, K, or ClK 0.1 0.1
II VCC = 5.5 V, VI = 7 V mA
PRE or ClR 0.2 0.2
J, K, or ClK 20 20
l> IIH VCC = 5.5 V, VI = 2.7 V /lA
r- PRE or ClR 40 40
en III
J, K, or ClK
VCC = 5.5 V, VI = 0.4 V
-0.2 -0.2
mA
l> IO~ VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
:2 VCC = 5.5 V, See Note 1 2.5 4.5 2.5 4.5 mA
ICC
C
tAli typical values are at VCC = 5 V, TA = 25°C.
l> tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
en NOTE 1: ICC is measured with J, K, ClK, and PRE grounded, then with J, K, ClK, and ClR grounded.
Q switching characteristics (see Note 2)
::0
C') VCC = 4.5 V to 5.5 V,
C CL = 50 pF,
~ PARAMETER
FROM TO Rl = 500 fl,
UNIT
en (INPUT) (OUTPUT) TA = MIN to MAX
MIN MAX MIN MAX
f rnax 25 30 MHz
tplH 3 20 3 15
PRE or ClR a orO ns
tpHl 4 22 4 18
tplH 3 18 3 15
ClK aorO ns
tpHl 5 23 5 19
128:
2-92 TEXAS
INSTRUMENlS
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLIP·FLOPS
WITH CLEAR· AN 0 PRESET

SN54AS112 SN74AS112
UNIT
PRE or ClR low
tw Pulse duration ClK high ns
ClK low
Setup time Data
tsu ns
before ClKI PRE or ClR inactive
th Hold time, data after ClKI ns
TA Operating free-air temperature -55 125 0 70 °C
electrical characteristics ~ver recommended operating free-air temperature range (unless otherwise noted)
SN54AS112 SN74AS112
MIN Typt MAX MIN TYpt MAX
VIK VCC = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V, 10H = -2 mA VcC-2 VCC-2 V
Val VCC = 4.5 V, 10l = 20 mA 0.35 0.5 0.35 0.5 V
J or K 0.1 0.1
II PRE or ClR VCC = 5.5 V, VI = 7 V 0.5 0.5 mA
ClK 0.5 0.5
J or K 0.02 0.02
IIH PRE or ClR VCC = 5.5 V, VI = 2.7 V 0.1 0.1 mA
en
~
ClK 0.1 0.1
J or K -1 -1
:::>
III PRE or ClR
ClK
VCC = 5.5 V, VI = 0.4 V -5.5
-5
-5.5
-5
mA
ua:
10 :.- VCC = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA
(3
ICC VCC = 5.5 V, See Note 1 38 38. mA
NOTE 1: ICC is measured with D, ClK, and PRE grounded, then with J, K, ClK, and PRE grounded, with K, K, ClK, and ClR grounded.
en
<t
C
VCC = 4.5 V to 5.5 V, z
Cl = 50 pF, <t
= 500O,
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
Rl
TA = MIN to MAX
UNIT en
-I
SN54AS112
Typt MAX
SN74AS112
Typt
<t
MIN MIN MAX
f max \ 175 175 MHz
tPlH 3 3
PRE or ClR QorO ns
tpHl 4 4
tPlH 3 3
ClK QorQ ns
tpHl 4 4
t All typical values are at VCC ; 5 V, TA ; 25 DC.

~The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS.
83 PRODUCT PREVIEW
Thl. page contain. Information on 8 product under
development. Texa. Instrument. reserves the right to TEXAS 2-93
change or dl.contlnue this product without notice.
INSTRUMENTS
POST OFFiCe BOX 225012 • DALLAS. TeXAS 75265
au»
r-
en
»
:2
c
»
en
(")
:lJ
(")
c
=i
en
2-94
DUAL J·I( NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS WITH PRESET
• Fully Buffered to Offer Maximum Isolation from SN54ALSl13A, SN54AS113. . J PACKAGE

External Disturbance SN74ALSl13A, SN74ASl13. . N PACKAGE
(TOP VIEW)
Carriers in Addition to Plastic and Ceramic DIPs. 1CLK VCC
o Dependable Texas Instruments Quality and Reliability 1K 2CLK
1J 2K
TYPICAL POWER 1PRE 2J
TYPICAL MAXIMUM
TYPE DISSIPATION 10 2PRE
CLOCK FREQUENCY
PER FLIP-FLOP 10 20
'ALS113A 40 MHz (CL = 15 pF) 6mW GND 25
'ASl13 175 MHz (CL = 50 pF) 95 mW
description SN54ALSl13A, SN54AS113 . FH PACKAGE

SN74ALSl13A, SN74ASl13 . FN PACKAGE
These devices contain two independent J-K negative-edge-
(TOP VIEW)
triggered flip-flops. A low level at the Preset input sets the
outputs regardless of the levels of the other inputs. When Preset
(PRE) is inactive (high). data at the J and K inputs meeting the
setup time requirements are transferred to the outputs on the
3 '2 1 2019
negative-going edge of the clock pulse. Clock triggering occurs at
a voltage level and is not directly related to the rise time of the 1J 4 2K
clock pUlse. Following the hold time interval, data at the J and K NC 4 NC
inputs may be changed without affecting the levels at the 1 PRE 6 2J
outputs. These versatile flip-flops can perform as toggle flip-flops NC 7 NC
by tying J and K high. 1Q B 2PRE
9 10111213
The SN54ALS113A and SN54ASl13 are characterized for
operation over the full military temperature range of - 55°C to 10 0 U 10 0
.-ZZNN
125°C. The SN74ALSl13A and SN74ASl13 are characterized t:l en
for operation from O°C to 70°C. NC - No internal connection t::
:::>
C,.)
a:
C,.)
FUNCTION TABLE logic symbol
INPUTS OUTPUTS
en
PRE CLK J K 0 a
1~ <t
L x X X H L
1J
1CLK c
H ~ L L 00 00 lK z
H ~ H L H L 2PR£ <t
H ~
~
L
H
H
H
L
TOGGLE
H 2J
2CLK
en
H ...J
H H X X 00 00 2K
<t
Pin numbers shown are for J and N packages,
Supply voltage, VCC ................................................................ 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range:SN54ALS 113A, SN54AS 113 ........ . . . . . . . . . . .. - 55°C to 125°C
SN74ALS113A, SN74ASl13 ....................... DoC to 70°C
Storage temperature range .................................... :............ - 65°C to 1 50°C
13 Copyright © 1982 by Texas Instruments Incorporated
. TEXAS 2-95
INSTRUMENTS
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS WITH PRESET

UNIT
PRE low 15 10
CLK low 20 16.5
tsu ns
before CLKl PRE inactive 22 20
th Hold time. data after ClK~ 0 0 ns
SN 54ALS 113A SN74ALS113A
VIK VCC = 4.5 V. II = -18 mA -1.5 -1.5 V
VOH VCC = 4.5 V to 5.5 V. IOH = -0.4 mA VCC-2 VCC-2 V
-
VCC = 4.5 V. IOl = 4 mA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V. IOl = 8 mA 0.35 0.5
J. K. or ClK 0.1 0.1
II VCC = 5.5 V. VI = 7 V mA
PRE 0.2 0.2
.-:t>en
J. K. or CLK 20 20
IIH Vce = 5.5 V. VI = 2.7 V p.A
PRE 40 40
J. K. or ClK -0.2 -0.2
III Vee = 5.5 V. VI = 0.4 V mA
:t> PRE -0.4 -0.4
z lot Vee = 5.5 V. Vo = 2.25 V

See· Note 1
-30
2.5
-112
4.5
-30
2.5
-112
4.5
mA
mA
C ICC VCC = 5.5 V.
:t> tAli typical values are at VCC = 5 V. T A = 25 cc.
en tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS.
NOTE 1: ICC is measured with J. K. ClK. and PRE grounded. then with J. K. ClK. and ClR grounded.

:D
o VCC = 4.5 V to 5.5 V.
c CL = 50 pF.
=t
en PARAMETER
'FROM TO RL = 500 fl.
UNIT
MIN MAX MIN MAX
f max 25 30 MHz
tplH 3 17 3 14
PRE QorO ns
tpHl 4 20 4 16
tplH 3 18 3 15
ClK QorO ns
tpHl 5 23 5 19
12
2-96 TEXAS
INSTRUMENTS
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS WITH PRESET

SN54AS113 SN74AS113
UNIT
PRE low
ClK low
Setup time Data
tsu ns
before ClKI PRE inactive
th' Hold time, data after ClKI ns
SN54AS113 SN74AS113
VIK VCC = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V, IOH = -2 rnA VCC-2 VCc-2 V
VOL VCC = 4.5 V, IOl = 20 rnA 0.35 0.5 0.35 0.5 V
J or K 0.1 0.1
II PRE VCC = 5.5 V, VI = 7 V 0.5 0.5 rnA
ClK 0.5 0.5
J or K 0.02 0.02
CJ)
IIH PRE VCC = 5.5 V, VI = 2.7 V 0.1 0.1 rnA
ClK 0.1 0.1 t:
J or K -1 -1 :::>
PRE = = -5.5 -5.5 rnA
u
III
ClR
VCC 5.5 V, VI 0.4 V
-5 -5
a:
lOt VCC = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA U
ICC VCC = 5.5 V, See Note 1 38 38 rnA CJ)
NOTE 1: ICC is measured with 0, ClK, and PRE grounded, then with 0, ClK, and ClR grounded. <t
c
switching characteristics (see Note 2) z
VCC = 4.5 V to 5.5 V. <t
Cl = 50 pF. CJ)
FROM TO Rl = 5000, ...J
PARAMETER UNIT
(INPUT) (OUTPUT) TA = MIN to MAX <t
SN54AS113 SN74AS113
f max 175 175 MHz
tplH 3 3
PRE QorQ ns
tpHl 4 4
tplH 3 3
ClK QorQ ns
tpHl 4 4
t All typical values are at VCC = 5 V, TA = 25°C.

33 PRODUCT PREVIEW
This page contains Information on a product under
development. Texas Instrumants reserva. the right to TEXAS 2-97
change or discontinue this product without notlca. INSTRUMENTS
- »
r-
en
»
2
C
»
en
~
::D
o
c:
=i
en
2-98
DUAL J-K NEGATIVE-EDGE-TRIGGERED FLIP-FLOPS
WITH PRESET, COMMON CLEAR, AND COMMON CLOCK
• Fully Buffered to Offer Maximum Isolation from SN54ALS114A, SN54AS114 _ J PACKAGE

External Disturbance SN74ALS114A. SN74AS114 _ N PACKAGE
(TOP VIEW)
Carriers in Addition to Plastic and Ceramic DIPs. ClR VCC
• Dependable Texas Instruments Quality and Reliability 1K ClK
1J 2K
TYPICAL POWER 1PRE 2J
TYPICAL MAXIMUM
TYPE DISSIPATION 1Q
CLOCK FREQUENCY
PER FLIP-FLOP 1Q
'ALS114A 40 MHz (CL = 15 pF) 6mW
GND -..._ _---'-
'AS114 175 MHz (CL = 50 pF) 95 mW
SN54ALS114A. SN54AS114 . FH PACKAGE

description
SN74ALS114A, SN74AS114 . FN PACKAGE
These devices contain two independent J-K negative-edge- (TOP VIEW)
triggered flip-flops. A low level at the Preset or Clear inputs sets
When Preset and Clear are inactive (high), data at the J and K
inputs meeting the setup time requirements are transferred to the 3 2 1 2019
outputs on the negative-going edge of the clock pulse. Clock 2K
triggering occurs at a voltage level and is not directly related to NC
..
the rise time of the clock pulse. Following the hold time interval, 2J
data at the J and K inputs may be changed without affecting the NC
levels at the outputs. These versatile flip-flops can perform as 2PRE
toggle flip-flops by tying J and K high.
The SN54AlSl14A and SN54ASl14 are characterized for 100 U 100

.... Z Z N N
operation over the full military temperature range of - 55°C to (!)
125°C. The SN74AlSl14A and SN74ASl14 are characterized en
for operation from O°C to 70°C.
!::
:::>
FUNCTION TABLE u
logic symbol a:
PRE CLR
INPUTS
CLK J K
OUTPUTS
Q Q CLR
u
L H X X X H L en
H L X X X L H
eLK
1m «
L L X X X H* H* 10
1J C
H H ~ L L QO 00 1K
1fi
2:
H
H
H
H
~
~
H
L
L
H
H
L
L
H
2m 20
«
H H ~ H H TOGGLE
2J
2K
2fi en
..oJ
H H H X X QO 00 «
"The output levels in this configuration are not guaranteed to meet the minimum levels for Pin numbers shown are for J and N packages.
VOH if the lows at Preset and Clear are near VIL maximum. Furthermore, this configuration
is nonstable; that is, it will not persist when either Preset Or Clear returns to its inactive
(high) level.
Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range:SN54AlS 114A, SN54AS 114 " . . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74AlSl14A, SN74ASl14 . . . . . . . . . . . . . . . . . . . . . .. OOC to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 150 °C
TEXAS 2-99
INSTRUMENTS
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS
recommended· operating conditions

UNIT
ClK low 20 16.5
tsu ns
th Hold time, data after ClKI 0 0 ns
electrical characteistics over recommended operating free-air temperature range (unless otherwise noted)
SN 54AlS 114A SN74AlS114A
VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH VCC = 4.5 V to 5.5 V, 10H = -0.4 mA VCC-2 VCC-2 V
VCC = 4.5 V, 10l = 4 mA 0.25 0.4
Val V
VCC = 4.5 V, IOl = 8 mA 0.35 0.5
J, K, or ClK 0.1 0.1
II VCC = 5.5 V, VI = 7 V mA'
PRE or ClR 0.2 0.2
J, K, or ClK 20 20
IIH VCC = 5.5 V, VI = 2.7 V I'A
PRE or ClR 40 40
J, K, or ClK -0.2 -0.2
III VCC = 5.5 V, VI = 0.4 V mA
lot VCC = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA
ICC VCC = 5.5 V, See Note 1 2.5 4.5 2.5 4.5 mA
t All typical values are at VCC = 5 V, T A = 25°C.

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS.
NOTE 1: ICC is measured with J, K, ClK, and PRE grounded, then with J, K, ClK, and ClR grounded.

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
FROM TO Rl = 500 n,
PARAMETER UNIT
MIN MAX MIN MAX
f max 25 30 MHz
tplH 3 20 3 15
PRE or ClR QorD ns
tpHl 4 22 4 15
tplH 3 18 3 15
ClK Q orO ns
tpHl 5 23 5 19
2-100 TEXAS
INSTRUMENTS
TYPES SN54ASl14, SN74ASl14
DUAL J·I( NEGATIVE·EDGE·TRIGGERED FLlp·FLOPS

SN54ASl14 SN74ASl14
UNIT
PRE or ClR low
ClK low
Setup time Data
tsu ns
before ClKI PRE or ClR inactive
th Hold time. data after ClKI ns
electrical characteristics over recommended operating free-air temperature range (unle,ss otherwise noted)
SN54ASl14 SN74ASl14
V1K VCC = 4.5 V. II = -18 rnA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V. 10H = -2 rnA VCC-2 VCC-2 V
VOL VCC = 4.5 V. 10l = 20 rnA 0.35 0.5 0.35 0.5 V
J or K 0.1 0.1
PRE 0.5 0.5
II
ClR
VCC = 5.5 V. VI = 7 V
1 1
rnA en
ClK 1 1 !::
J or K \ 0.02 0.02 ::>
PRE 0.1 0.1 C,.)
IIH
ClR
VCC = 5.5 V. VI = 2.7 V
0.2 0.2
rnA a::
ClK 0.2 0.2 C,.)
J or K -1 -1
en
III
PRE
ClR
VCC = 5.5 V. VI = 0.4 V
-5.5
-11.5
-5.5
-11.5
rnA «
ClK -10.5 -10.5 c
10i: = = -30 -112 -30 -112 rnA 2
ICC
VCC
VCC =
5.5 V.
5.5 V.
Va
See Note 1
2.25 V
38 38 rnA «
t All typical values are at VCC = 5 V. T A = 25°C. . en
-J
i:The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS.
NOTE 1: ICC is measured with J. K. ClK,and PRE grounded, then with J, K. ClK. and ClR grounded. «
PRODUCT PREVIEW
This page contains information on a product under
development. T axas Instruments r.saNaa the right to TEXAS 2-101
DUAL J·K NEGATIVE·EDGE·TRIGGERED FLIP FLOPS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
FROM TO RL = 500 n. UNIT
SN54AS114 SN74AS114
f max 175 175 MHz
tplH 3 3
PRE or ClR QorO ns
tpHl 4 4
tplH 3 3
ClK QorQ ns
tpHl . 4 4
t All typical values are at Vce = 5 V. T A = 25°e.

- ~
r-
en
~
2
o
~
en
o
~
o
c
=i
en
PRODUCT PREVIEW 12
2- 10 2
development. TIxas Instruments rlsarves the right to
TEXAS
3·LlNE TO B·LlNE DECODERS/DEMULTIPLEXERS WITH ADDRESS REGISTERS
• Combines Decoder and 3-Bit Address Register SN54ALS131. SN54AS131 .•• J PACKAGE
SN74ALS131. SN74AS131 ... N PACKAGE
• Incorporates 2 Enable Inputs to Simplify Cascading (TOP VIEW)
e Package Options Include Both Plastic and Ceramic
Chip Carriers in Addition to Plastic and Ceramic A 1 U16 VCC
DIPs B 2 15 YO
C 3 14 Y1
• Dependable Texas Instruments Quality and ClK 4 13 Y2
Reliability <32 =5 12 Y3
G1 6 11 Y4
description Y7 7 10 Y5
The ' AlS 131 and 'AS 131 are three-line to eight-line GND 8 9tJ Y6
decoders/demultiplexers with registers on the three address
inputs. When the clock input (ClK) goes from low to high,
SN54ALS131. SN54AS131 ... FH PACKAGE
the' AlS 131 and 'AS 131 act as decoders/demultiplexers
SN74ALS131. SN74AS131 ... FN PACKAGE
and the address present at the select inputs (A, B, and C)
(TOP VIEW)
is stored in the registers. Further address changes are
ignored until the next transition of ClK. The output enable U
U Uo
controls, G1 and <32. control the state of the outputs IXl<{Z»
independently of the select or ClK inputs. All of the outputs
are high unless G 1 is high and <32 is low. The' AlS 131 and Yl
,AS 131 are ideally suited for implementing glitch-free ClK Y2
decoders in strobed (stored-address) applications in bus- NC NC
oriented systems. <32 Y3
The SN54AlS131 and SN54AS131 are characterized for G1 Y4
operation over the full military temperature range of - 55°C
to 125°C. The SN74AlS131 and SN74AS131 are !'OUCCIO
>ZZ»
characterized for operation from ooC to 70°C. (!) CJ)
!:::
:::>
u
logic symbols (alternatives) a:
U
(4) XIV DMUX CJ)
ClK C8
<t
0 YO
A C
B 2
A 2
C
2
B
<t
CJ)
C
....I
4
G1
<t
5 Y5
EN G1
G2 Y6
G2 Y6
7 Y7
Y7

13
TEXAS 2-103
INSTRUMENTS
3·L1NE TO 8·L1NE DECODERS/DEMULTIPLEXERS WITH ADDRESS REGISTERS
logic diagram (positive logic)
ENABLE { 0 2
INPUTS
(15)
G1 VO
(14)
V1
ClK
(13)
V2
(12)
A V3
DATA
(11) OUTPUTS
V4
SELECT (10)
B V5
INPUTS
(9)
V6
(7)
C V7

FUNCTION TABLE
INPUTS
ClK ENABLE SELECT OUTPUTS
G1 G2 C B A VO V1 V2 V3 V4 V5 V6 V7
X X H X X X H H H H H H H H
X l X X X X H H H H H H H H
t H L L L L L H H H H H H H
t H L L L H H L H H H H H H
t H L L H L H H L H H H H H
t H L L H H H H H L H H H H
t H L H L L H H H H L H H H
t H L H L H H H H H H L H H
t H L H H L H H H H H H L H
t H L H H H H H H H H H H L
L OUTPUTS CORRESPONDING
or H L X X X TO STORED ADDRESS, L;
H ALL OTHERS, H
Supply voltage, Vee ................................................................. 7 V
Input voltage .................................................'. . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS131, SN54AS131 .................... - 55°C to 125°C
. SN74ALS131, SN74AS131 ........................ ooe to 70°C
Storage temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50°C
128
2-104 TEXAS
INSTRUMENlS

SN54ALS131 . SN74ALS131
UNIT
fclock elock frequency 0 40 0 50 MHz
Pulse duration
IelK high 12.5 10
ns
tw
I elK low 12.5 10
tsu Setup time at A. B. and e before elK t 15 10 ns
th Hold time at A. B. and e after elK t 0 0 ns
SN54ALS131 SN74AlS131
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
Vee = 4.5 V. 10l = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. 10l = 8 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 /LA
III Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
lot Vee = 5.5 V. Va = 2.25 V -30 -112 -30 -112 mA en
lee Vee = 5.5 V 5 11 5 11 mA !:::
::>
"tAli typical values are at Vee; 5 v. TA ; 25°e. .
u
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS'
a:
U
en
«
Vcc = 4.5 V to 5.5
= 50 pF.
V. c
Cl 2
PARAMETER
FROM TO Rl
TA
= 500 fl.
= MIN to MAX UNIT «
(INPUT) (OUTPUT)
SN54ALS131 SN74ALS131
en
...J
f max
MIN
40
MAX MIN
50
MAX
MHz
«
tplH 8 28 8 25
elK y ns
tpHl 7 24 7 20
tPlH 7 24 7 20
Gl y ns
tpHl 6 20 6 17
tplH 5 18 5 15
G2 Y ns
tpHl 5 18 5 15
'TEXAS 2-105
INSTRUMENlS

SN54AS131 SN74AS131
UNIT
fclock elock frequency MHz
Pulse duration
I elK high
ns
tw
I elK low
tsu Setup time at A. B. and e before elK t ns
th Hold time at A. B. and e after elK t ns
SN54AS131 SN74AS131
VIK Vee = 4.5 V. II = -18 mA -1.2 .-1.2 V
..
VOH Vee = 4.5 V to 5.5 V. 10H = -2 mA vee- 2 vee- 2 V
VOL Vee = 4.5 V. 10l = 20 mA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V. VI =7V mA
IIH Vee = 5.5 V. VI = 2.7 V /LA
III Vee = 5.5 V. VI = 0.4 V mA
lot Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
= 5.5 V 16 16 mA
l> lee Vee
r- t All typical values are at Vee ~ 5 V. TA ~ 25°e.
CJ) ~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
l>
2
C
l>
CJ)
Vcc = 4.5 V to 5.5 V.
(') Cl = 50 pF.
:0 FROM TO RL = 500 n.
PARAMETER UNIT
(') (INPUT) (OUTPUT) TA = MIN to MAX
c SN54AS131 SN74AS131
=i
CJ) f max
MHz
tplH 5.4 5.4
elK y ns
tpHl 5.3 5.3
tpLH 6.2 6.2
G1 y ns
tpHl 5.6 5.6
tplH 5.4 5.4
G2 Y ns
tpHl 5.3 5.3
tAli typical values are at Vee ~ 5 V. TA ~ 25°e.

PRODUCT PREVIEW 1.
2 -1 a6
This page contains Information on 8 product under
development. Texe. In.trument. re.erv.. the right to TEXAS
change or discontinue this product without notics. INSTRUMENTS
D2661. APRIL 1982-REVISION DECEMBER 1983
o Package Options Include Both Plastic and

and Ceramic DIPs
o Dependable Texas Instruments Quality
and Reliability
description SN54ALS133 ... J PACKAGE

SN74ALS133 ... N PACKAGE
These devices contain a single 1 3-input NAND gate.
(TOP VIEW)
They perform the boolean functions in positive logic:
Y = A·B·C·D·E·F·G·H·I·j·K·L·M A VCC
B M
Y = A+B+C+D+E+F+G+H+T+J+K+L+M
C
The SN54ALS133 is characterized for operation D
over the full military temperature range of - 55°C to E j
125°C. The SN74ALS133 is characterized for F I
operation from 0 °C to 70°C. G H
GND Y
FUNCTION TABLE
OUTPUT
INPUTS A THRU M
y
SN54ALS133 ... FH PACKAGE
All inputs H L SN74ALS133 ... FN PACKAGE
One or more inputs L H (TOP VIEW)
logic symbol
(1) C
A & L
(2) D K
(3) NC NC
c
(4) E j
0
(5)
F
(6)
(7) (!)ClU>-::r:
(9) y 22
G (!)
(10)
H
(11) NC - No internal connection
(12)
(13)
K
(14)
M (15)
TEXAS 2-107
INSTRUMENlS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage ............................................................... : . . . . . .. 7 V
Operating free-air temperature range: SN54ALS133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS133 .................................. ooe to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C

UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V IOH = -0.4 mA vee- 2 vee- 2 V
lEI VOL
Vee
Vee
= 4.5
= 4.5
= 5.5
V,
V
IOl = 4 mA
IOl = 8 mA
VI = 7 V
0.25 0.4 0.25
0.35
0.4
0.5
0.1
V
»
r-
II
IIH
Vee
Vee = 5.5
V,
V, VI = 2.7 V 20
0.1
20
mA
/LA
= 5.5 VI = 0.4 V
o III
lot
Vee
Vee = 5.5
V,
V, Vo = 2.25 V -30
-0.1
-112 -30
-0.1
-112
mA
mA
»
z leeH Vee
Vee
= 5.5
= 5.5
V,
V,
VI
VI
=
=
OV
4.5 V
0.24
0.56
0.34
0.8
0.24
0.56
0.34
0.8
mA
mA
leel
c tAli typical values aree at Vee = 5 V, TA = 25°C.
»
o
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS.

:D
(') VCC = 4.5 V to 5.5 V
c CL = 50 pF,
=t
o
I
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL = 500 {}
TA = MIN to MAX
UNIT
MIN MAX MIN MAX
tpLH Any Y 3 14 3 11 ns
tPHl Any Y 5 28 5 25 ns
NOTE 2: For load Circuit and voltage waveforms, see page 1-12.
2-108 TEXAS
INSTRUMENTS
3·LlNE TO 8·LI~JE
DECODERS/DEMULTIPLEXERS WITH ADDRESS LATCHES
o Combines Decoder and 3·Bit Address Latch SN54ALS137. SN54AS137 ... J PACKAGE
• Incorporates 2 Output Enables to Simplify Cascading
(TOP VIEW)
o Package Options Include Both Plastic and Ceramic
Chip Carriers in Addition to Plastic and Ceramic DIPs
A Vce
B YO
o Dependable Texas Instruments Quality and Reliability C Y1
GL Y2
description
G2 Y3
The 'ALS137 and 'AS137 are three-line to eight-line G1 Y4
decoder/demultiplexer with latches on the three address inputs. Y7 Y5
When the latch-enable input (GI) is low, the 'ALS137 and 'AS137 GND Y6
acts as a decoder/demultiplexer. When GI goes from low to high,
the address present at the select inputs (A, B, and C) is stored
in the latches, Further address changes are ignored as long as GL
remains high. The output enable controls, G 1 and (32, control the SN54ALS137, SN54AS137 ... FH PACKAGE
outputs independently of the select or latch-enable inputs, All of SN74ALS137. SN74AS137 .•. FN PACKAGE
the outputs are forced high if G 1 is low or <32 is high. The' ALS 137 (TOP VIEW)
and 'AS137 are ideally suited for implementing glitch-free
U
decoders in strobed (stored-address) applications in bus-oriented U UO
IIl<l:Z>>-
systems.
The SN54ALS137 and SN54AS137 are characterized for

C Y1
operation over the full military temperature range of - 55°C to
125°C. The SN74ALS137 and SN74AS137 are characterized for
GI. Y2
NC NC
operation from ooC to 70°C,
<32 Y3
G1 Y4
r--OU(,OL()
>-zz>->-
(!)
...
en
::J
NC - No internal connection U
a:
U
en
logic symbols (alternatives) <t
C
2
<t
en
...J
<t
TEXAS 2-109
INSTRUMENTS
3·LlNE TO B·LlNE DECODERSIDEMULTIPLEXERS WITH ADDRESS LATCHES
V1
V2
SELECT
INPUTS
DATA
OUTPUTS
V6
LATCH { (4)
ENABLE Gl
G2 (5)
OUTPUT
ENABLES (6)
{ G1
FUNCTION TABLE
INPUTS
OUTPUTS
ENABLE SELECT
GL G1 (32 C B A VO V1 V2 V3 V4 V5 V6 V7
X X H X X X H H H H H H H H
X L X X X X H H H H H H H H
L H L L L L L H H H H H H H
L H L L L H H L H H H H H H
L H L L H L H H L H H H H H
L H L L H H H H H L H H H H
L H L H L L H H H H L H H H
L H L H L H H H H H H L H H
L H L H H L H H H H H H L H
L H L H H H H H H H H H H L
X Output corresponding to stored
H H L X X
address, L; all others, H
Supply voltage, Vee ........................ "............. , ..................-......... 7 V
Input voltage .................................................................•.... , 7 V
Operating free-air temperature range: SN54ALS137, SN54AS137 .................... - 55°C to 125°C
SN74ALS137, SN74AS137 ........................ ooe to 70°C
Storage temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 DC to 150 DC
12:
2-110 TEXAS
INSTRUMENTS
3·LlNE TO B·LlNE DECODERS/DEMULTIPLEXERS WITH ADDRESS LATCHES

UNIT
V,H High-level input voltage 2 2 V
V,l low-level input voltage 0.8 0.8 V
tw Pulse duration. GL low 15 10 ns
tsu Setup time at A. B. and e before GLI 15 10 ns
th Hold time at A. B. and e after GLI 5 5 ns
SN54AlS137 SN74AlS137 UNIT
PARAMETER TEST CONDITIONS
V,K Vee = 4.5 V.
" =
-18 rnA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V. IOH = -0.4 mA Vee-2 Vee-2 V
Vee = 4.5 V. IOL = 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vee =
4.5 V. IOL = 8 rnA 0.35 0.5
Vee:: 5.5 V. V, = 7 V 0.1 0.1 rnA
"
"H Vee = 5.5 V. V, = 2.7 V 20 20 p.A
',L Vee = 5.5 V. V, = 0.4 V -0.1 -0.1 rnA
IO~ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V 5 11 5 11 rnA
(/)
tAli typical values are at Vee = 5V.TA = 25°C.
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS' t::
:::>
()
a:
()
Vcc - 4.5 V to 5.5 V,
(/)
Cl = 50 pF,
FROM TO Rl = 500 n, cd:
PARAMETER UNIT
(INPUT) (OUTPUT) TA = MIN to MAX C
SN54AlS137 SN74ALS137 2
MIN MAX MIN MAX cd:
tpLH 5 25 5 20 (/)
A,B,e y ns
tpHL 6 25 6 20 ..J
tpLH
02 y
4 15 4 12
ns cd:
tpHL 5 18 5 15
tpLH 5 21 5 17
Gl y ns
tpHL 5 19 5 15
tpLH 7 27 7 22
GI. y ns
tpHL 7 25 7 20
NOTE. 1: For load circuit and voltage waveforms. see page 1-12.
TEXAS 2-111
INSTRUMENTS
3·LlNE TO B·LlNE DECODERS/MULTIPLEXERS WITH ADDRESS LATCHES

SN54AS137 SN74AS137
UNIT
tw Pulse duration, GL low ns
tsu Setup times at A, B, and e before GLI ns
th Hold time at A, B, and e after GLI ns
electrical characteristics over rec~mmended operating free-air temperature range (unless otherwise noted)
SN54AS137 SN74AS137
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH Vee =
4.5 V to 5.5 V, IOH = -2 rnA vee- 2 vee- 2 V
VOL Vee - 4.5 V, 10L = 20 rnA 0.35 0.5 0.35 0.5 V
Enable
II Vee = 5.5 V, VI = 7 V rnA
A, B,e
Enable
IIH Vee = 5.5 V, VI = 2,7 V ~A
-
A,B,e
Enable -0.05 -0.05
IlL Vee = 5.5 V, VI = 0.4 V rnA
A, B,e -0.05 -0.05
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V 16 16 rnA
»
.- tAli typical values are at Vee = 5 V, TA = 25°e./
~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
t/)
»
2
VCC = 4.5 V to 5.5 V,
C CL = 50 pF,
»t/) PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL
TA
= 500 n,
= MIN to MAX
UNIT
Q MIN
SN54AS137
Typt MAX
SN74AS137
MIN Typt MAX
::D 6.6 6.6
(") tPLH
A, B,e y ns
c: tpHL 7.1
5.4
7.1
5.4
~
tPLH y
<32 ns
tpHL 5.3 5.3
t/)
tpLH 6.2 6.2
G1 y ns
tPHL 5.6 5.6
tpLH 5.4 5.4
GI. y ns
tpHL 5.3 5.3
tAli typical values are at Vee 5 V, TA = 25°e.

NOTE 1: For load circuit, and voltage waveforms, see page 1-12.
PRODUCT PREVIEW
Thl. page contain. information on 8 product under
2 -11 2 development. T.xa.ln.trument.....rv.. the right to TEXAS
chang. or dl.continue thl. product wl1hout notlc•. INSTRUMENTS
3·LlNE TO 8·LlNE DECODERS/DEMULTIPLEXERS
o Designed Specifically for High·Speed Memory SN54ALS138, SN54AS138 ... J PACKAGE

Decoders and Data Transmission Systems SN74ALS138. SN74AS138 ... N PACKAGE
(TOP VIEWI
o Incorporates 3 Enable Inputs to Simplify Cascading
and/or Data Reception A VCC
B YO
C Y1
G2A Y2
o Dependable Texas Instruments Quality and Reliability G2B Y3
G1 Y4
description Y7 Y5
GND YB
The' ALS 138 and' AS 138 circuits are designed to be used in high-
performance memory-decoding or data-routing applications
requiring very short propagation delay times. In high-performance
memory systems these decoders can be used to minimize the
effects of system decoding. When employed with high-speed SN54ALS138. SN54AS138 ... FH PACKAGE
memories utilizing a fast enable circuit, the delay times of these SN74ALS138. SN74AS138 ... FN PACKAGE
decorders and the enable time of the memory are usually less than (TOP VIEW)
the typical access time of the memory. This means that the
u
effective system delay introduced by the Schottky-clamped u Uo
co~z>>-
system decoder is negligible.
3 2 1 2019
The conditions at the binary select inJ;luts and the three enable
inputs select one of eight input lines. Two active-low and one
C Y1
G2A Y2
active-high enable inputs reduce the need for external gates or
NC NC
inverters when expanding. A 24-line decoder can be implemented
without external inverters and a 32-line decoder requires only one G2B Y3
G1 Y4
inverter. An enable input can be used as a data input for
demultiplexing applications.
9 10 111213
en
..... OUCOLl)
>-ZZ>->- !:::
operation over the full military temperature range of - 55 °C to
(!)
:J
125 °C. The SN74ALS138 and SN74AS138 are characterized for
U
operation from ooC to 70°C.
NC - No internal connection a:
U
en
logic symbols (alternatives)
<t
C
:2'.:
<t
A (1)
B (2)
en
..J
c (3) <t

13
TEXAS 2-113
INSTRUMENTS
. . '
. :'. , . , : ' .: .. "., .:.... .... ' .
TYPES'SN54ALS138; SN54AS,138,.SN74ALS138; 'SN74AS138

3·LlNE TO 8·LlNE DECODERS/DEMULTIPLEXERS '
YO
(1)
A
Y1
Y2
(2)
SELECT 8
INPUTS
Y3
DATA.
OUTPUTS
Y4
'c _~(3.;..1_---4
-.;.----....
........
ENABLE {%;~ ===(4::)=:::::rl

INPUTS
G1
Pin numbers shown are; for J and N packages.
~
l> FUNCTION TABLE .
r- ENABLE SELECT
til OUTPUTS
INPUTS INPUTS
l> G1 G2* C B A YO Y1 Y2 V3 V4 Y5 Y6 Y1
2 X H X X X H H .H H H H H H
C L X X X X H H H H i-! H H H
l> H L L L L L H H. H H H H H
til H L L L H H L .H H H H H H
H L L H L H H 'L H H H H H
Q H L L H H H H H L H H H H
::c
(')
H L H L L H H. H :H L H H H
H L H L H H H Ii H H H H
c H L H H L H H H H H
L
i-l L H
=i H. L H H H H ,H H H H H 'H L
til
absolute maximum ratings 'over operating free·air tenipe~cltJrerange (unless otherwise noted)
Supply voltage, Vee ................ '......... '. :': :. " .'......................... " ..... '.' .... 7 V
Input voltage: .. '.' .............. '... : .' ..' .... '.' .......... '........ '........ '. ; ............ '.' . '; . '.' .. 7 V
Operating free-air temperature range: SN54ALS138, SN54AS138 ' .......... ' . . . . . . .. .. ,- 55 0 e to i 25 °e
SN74ALS138, SN74AS'138 . '" : ...............••.. ooe to 70 0 e
Storage temperature range.; ...... , ........... ~ ...... :............. ~ .......... -65'o e to 150~e·
2-114 TEXAs' .
INSTRUMENTS
POST OFFICE 'BOX 225012 • DALLAS. TE'XAS 75265
TYPES SN54ALS13B. SN74ALS13B
3·LlNE TO B·LlNE DECODERS/DEMULTIPLEXERS
SNS4ALS138 SN74ALS138
UNIT
Vee Supply voltage 4.S S 5.5 4.5 5 5.5 V
electrical characteristics over ;ecommended operating free-air temperature range (unless otherwise noted)
VIK Vee_= 4.5 V. II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V to 5.5 V. 10H = -0.4 mA Vee- 2 Vee- 2 V
Vee = 4.5 V. 10L = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V; 10L = 8 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
10+ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V 5 10 5 10 mA
tAli typical values are at Vee; 5 V. TA ; 25°e.

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS.
CJ)
!=
:::J
switching characteristics (see Note 1) CJ
Vce = 4.S V to S.S V.
ex:
CL = so pF. CJ
FROM TO RL = SOO n. CJ)
PARAMETER
UNIT
«
MIN
SNS4ALS138
MAX MIN
SN74ALS138
MAX
c
2
tpLH
tPHL
A. B. e Any Y
6
6
27
22
6
6
22
18
ns «
tpLH 4 20 4 17 CJ)
Enable Any Y ns ...J
tpHL
5 20 5 17
«
TEXAS 2-115
INSTRUMENTS
TVPES SN54AS1-38,·SN7.4AS138 , ,
3-L1NE T08'·LI~E'DEC~D.ERS/DEMULTIPLEXERS
, , , '
SN54AS138 SN74AS138
UNIT
"
vee' ,Supply voltage 4.5 5 5.5 4,5 5 5,5 V
VIH ~igh-Ievel Input vOltage ' 2 2 V
,'OH' High-level output current, -2 -2 rnA
IOL : low-level output. current 20 20 rnA
TA '. Operating free-air temperature -55 125 0 70 °e
electrical characteristics ,over recommended operating free-air temperature range (unless otherwise noted)
SN54AS138 SN74AS138
,', "
" MIN Typt MAX MIN Typt MAX
. ,V'K Vee.= 4:5 V. II =-18 rnA V
VOH vee = 4.5 V to 5.5 v, 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee."" 4.5 v, 10L = 20 rnA 0.35 0,5 0.35 0.5 V
II Vee'" 5.5 v, VI = 7 V rnA
IIH Vee,:, 5.5 V. VI = 2.7 V p.A
IlL vee == 5.5 v, VI = 0.4 V rnA
10+ vee,:" 5.5 v, Vo =- 2.25 V -30 -112 -30 -112 rnA
-
. ICC ' , Vee"" 5.5 V 13 13 rnA
tAli typical values are at Vee = 5 V. TA = 25°e,

l>
r- switchin~ char~cterisii,cs (see Note 1)
C/)
Vcc = 4.5 V to 5,5 v,
l> CL = 50 pF,
2 FROM TO RL = 500 n,
C PARAMETER
UNIT
l> SN54AS138 SN74AS138

C/)
Q tPLH '
tpHL
A,8,e Any Y
5.6
6.1
5.6
6.1
ns
:D "
'.
o tpLH
Enable Any Y
5,8 5,8
ns
c tPHL ' , 5.5 5.5
=i
(/)
.'
t All typical valu.es are at Vee '" 5 V, TA = 25°e.
NOTE1: For lOad 'circuit ~nd voltage waveforms, see page 1-12.
-' .... '.. .' ..... ),.,'..

• PRODuct PREViEW
This pagi contm~ .nfo,;,;.t.o;. on ,; JJiociuet unci.,
2 -11 6 development. Texe.lnitninMont.......... the right to TEXAS
chenge or dJacontinue thI. product wfthout notice. INSTRUMENTS
POST OFFiCe BOX 225012 • DAL.LAS, TeXAS 75265
DUAL 2·LlNE TO 4·LlNE DECODERS/DEMULTIPLEXERS
o Designed Specifically for High·Speed Memory SN54ALS139. SN54AS139 ... J PACKAGE

Decoders and Data Transmission Systems SN74ALS139. SN74AS139 ... N PACKAGE
(TOP VIEW)
o Incorporates 2 Enable Inputs to Simplify Cascading
and/or Data Reception 1G VCC
1A 2G
'0 Package Options Include Both Plastic and Ceramic
1B 2A
1YO 2B
o Dependable Texas Instruments Quality and Reliability 1Y1 2YO
1Y2 2Y1
description 1Y3 2Y2
The' ALS 139 and' AS 139 circuits are designed to be used in high- GND 2Y3
performance memory-decoding or data-routing applications
requiring very short propagation delay times. In high-performance
memory systems. these decoders can be used to minimize the SN54ALS139. SN54AS139 ... FH PACKAGE
effects of system decoding. When employed with high-speed SN74ALS139. SN74AS139 ... FN PACKAGE
memories utilizing a fast-enable circuit. the delay times of these (TOP VIEW)
decoders and the enable time of the memory are usually less than
U
the typical access time of the memory. This means that the « 1c.9 U UIc.9
....-....-Z>N
effective system delay introduced by the Schottky-clamped
system decoder is negligible. 3 2 1 20 19
1B 2A
The' ALS 139 and' AS 139 are comprised ~f two individual two-
1YO 2B
line to four-line decoders in a single package. The active-low
NC NC
enable input can be used as a data line in demultiplexing
1Y1 7 2YO
applications. These decoders/demultiplexers feature fully buffered
1Y2 8 2Y1
inputs. each of which represents only one normalized load to its
9 10 11 1213
driving circuit. All inputs are clamped with high-performance
Schottky diodes to suppress line-ringing and simplify system MQUMN
design.
>-ZZ>->-
c.9 NN
en
I-
The SN54ALS139 and SN54AS139 are characterized for NC - No internal connection ::>
operation over the full military temperature range of - 55°C to U
125°C. The SN74ALS 139 and SN74AS 139 are characterized for 0:::
operation from ooC to 70°C. U
en
logic symbols (alternatives) <t
c
:2
<t
en
..J
<t
Pin numbers shown are for J and N packages

13 PRODUCT PREVIEW
ThIs document contains information on a product under
development. Texas Instruments reserves the right to
changa or discontinue this product without notice.
TEXAS 2-117
INSTRUMENTS
TYPES SN54ALS139, SN54AS13t SN74ALS~39,SN74~S139
DUAL 2·LlNE TO 4·LlNE DECODERS/DEMULTI~LEXE~S'
FUNCTION TASLE
INPUTS
OUTPUTS
ENABLE SELECT
G B A YOY1Y2 V3
H X X HH .Ii H
L L L LH H H
L L H HL H H
L H L HH L H
L H H H HH L
functional block diagram (positive logic)
ENA8LE1G
-
SELECT { ' 1A
INPUTS 18
DATA
OUTPUTS
»
r-
en
»
2
C
»
en SELECT
2A(14)
INPUTS { 28(13)
Q
:x:J
o
c:
=i
en Pin numbers shown are for J and N packages.
. ,
absolute maximum ratings over operating free-air temperature range (unl.ess otherwise noted)
Supply voltage, VCC .............................. ;' .',:. • . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage ..................................... ,: ..... : . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS 139, SN54AS139 . '.• ; '. . . . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS139, SN74AS139 ..... '. ~ ............... " O°C to 70°C
Storage temperature range ............................. ' ..• ~ '................ , - 65°C to 150 °C
2-118 TEXAS'
INSTRUMENTS',
POST OFFIce BOX 225012 • ,DALLAS. TexAS 75265

UNIT
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
Vee = 4.5 V. IOL = 4 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 8 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
...
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
lo~ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V 4.5 4.5 mA

en
!::
:::>
switching characteristics (see Note 1) ua:
CL = SO pF.
U
FROM TO RL = SOO n. en
PARAMETER
UNIT
«
SNS4ALS139
MIN Typt MAX
SN74ALS139
MIN Typt MAX
c
2:
tpLH
tpHL
A or B Y
10
10
10
10
ns «
tpLH 8 8 en
...J
IT y ns
tpHL 8 8
«
13
TEXAS 2-119
INSTRUMENTS

SNS4AS139 SN74AS139
UNIT
Vee Supply voltage 4.S 5 5.5 4.5 5 5.5 V
SN54AS139 SN74AS139
VIK Vee ~ 4.5 V, II ~ -18 mA -1.2 -1.2 V
VOH Vee ~ 4.5 V to 5.5 V, 10H ~ -2mA Vee- 2 Vee- 2 V
VOL Vee ~ 4.5 V, 10L ~ 20 mA 0.35 0.5 0.35 0.5 V
II Vee ~ 5.5 V, VI ~ 7 V 0.1 0.1 mA
IIH Vee ~ 5.5 V, VI ~ 2.7 V 20 20 I'A
IlL Vee ~ 5.5 V, VI ~ 0.4 V -0.5 -0.5 mA
lot Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA
lee Vee ~ 5.5 V 13 13 mA
- tAli typical values are at Vee= 5 V. TA = 25°e.

~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
»
r- switching characteristics (see Note 1)
en
»
2
Vcc
CL ~
= 4.S V
so pF,
to 5.S V,
FROM TO RL ~ 500 n,
C PARAMETER
UNIT
»
en MIN
SN54AS139
Typt MAX MIN
SN74AS139
Typt MAX
~ tPLH 5.5 5.5

A or B Y ns
tpHL 6 6
:D
o tpLH
IT Y
5.5 5.5
ns
c tpHL 5 5
=i t All typical values are at Vee = 5 V. TA = 25°e.

en NOTE 1: For load circuit and voltage waveforms. see page 1-12.
12
2-120 TEXAS
INSTRUMENTS
1 OF 8 DATA SELECTORS/MULTIPLEXERS
D2661, APRIL 1982-REVISED DECEMBER 1983
• 8-Line to 1-Line Multiplexers SN54ALS151,SN54AS151 ... JPACKAGE

Can Perform As: SN74ALS151, SN74AS151 ... N PACKAGE
Boolean Function Generators (TOP VIEW)
Parallel-to-Serial Converters
Data Source Selectors
03 VCC
• Input Clamping Diodes Simplify System Design 02 04
01 05
• Fully Compatible With Most TTL Circuits 00 06
• Package Options Include Both Plastic and Ceramic y 07
Chip Carriers in Addition to Plastic and Ceramic DIPs W A
G B
• Dependable Texas Instruments Quality and Reliability GNO C
description
SN54ALS151,SN54AS151 ... FHPACKAGE
These monolithic data selectors/multiplexers provide full binary
decoding to select one of eight data sources. The strobe input (G)
SN74ALS151,SN74AS151 ... FNPACKAGE
(TOP VIEW)
must be at a low logic level to enable the inputs. A high level at
the strobe terminal forces the W output high and the Y output U
low. N M U U'<t
ooz>o
05
125°C. The SN74ALS151 and SN74AS151 are characterized
06
for operation from 0 °C to 70°C.
NC
D7
A
CJ)
!::
::J
FUNCTION TABLE NC - No internal connection U
INPUTS OUTPUTS
a:
SELECT STROBE U
y W logic symbol
C B A G CJ)
X X X H L H <t
L L L L 00 00
L L H L 01 DT MUX C
L 02 02 G EN 2
L H L
<t
:}G~
A
L H H L 03 D3 B
H L L L 04 04 CJ)
c ...J
H L H L 05 I55
H H L L 06 06
DO
01
(5)
y
<t
H H L 07 07 (6) W
H D2
(1)
H = high level, L = low level, X = irrelevant D3
(15)
DO, Dl . , , D7 = the level of the D respective input D4
(14)
D5
(13)
D6
(12)
D7

83
TEXAS 2-121
IN SfRUM ENTS
(7)
G
(4)
DO '\
. "----"
(3)
01
-t.-/
(2)
02
~
(1)
03
DATA
INPUTS (15)
-.J- -
(5)
(6)
Y
04 w
---, qJ-
(14)
05
....... aJ-
- --
(13)
06
~
~
(12)
07
:t> ~t::L...-.I
r-
en A
(11)
:t> DATA
2 SELECT B
(10)
C (BINARY)
.....
:t> C
(9)
en
Q Pin numbers shown are for J and N packages.
:D
("')
c absolute maximum ra~ings over operating free-air temperature range (unless otherwise noted)
=i
en Supply voltage, V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V .
Operating free-air temperature range: SN54ALS151, SN54AS151 . . . . . . . . . . . . . . . . . . . . - 55°C to 1250C
SN74ALS151,SN74AS151 . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " - 65°C to 150°C
12·
2-122 TEXAS
INSTRUMENTS

UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V IOL = 24 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p,A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V, Inputs at 4.5 V 7.5 12 7.5 12 mA

;The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' en
switching characteristics (see Note 1) '=::::>
Vce = 4.5 V to 5.5 V, u
CL = 50 pF, a:
FROM TO RL = 500O,
PARAMETER UNIT U
SN54ALS151 SN74ALS151 en
MIN MAX MIN MAX <t
tpLH
A, B, or e y
4 21 4 18
ns
C
tPHL 8 28 8 24 2
tPlH
A, B, or e w
7 28 7 24
ns
<t
tpHL 7
3
26
12
7
3
23
10
en
tpLH
Any D y ns
-J
tpHL 5 18 5 15 <t~
tpLH 3 18 3 15
Any D W ns
tpHL 4 18 4 15
tpLH 4 21 4 18
G Y ns
tpHL 4 23 4 19
tpLH 5 23 5 19
G W' ns
tPHL 5 26 5 23-·
~83
TEXAS 2-123
INSTRUMENTS
POST OFFICE BOX 225012 • OALLAS. TEXAS 75265

SN54AS151 SN74AS151
UNIT
IOL Low-level output current 32 -48 rnA
SN54AS151 SN74AS151
VIK Vee = 4.5 V, II =
-18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -12 rnA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 rnA 2.4 3.3
Vee = 4.5 V, IOL = 32 rnA 0.25 0.5
VOL V
Vee = 4.5 V IOL = 48 rnA 0.35 0.5
A, B, or e 0.2 0.2
II Vee = 5.5 V, VI = 7 V rnA
All others 0.1 0.1
A, B, or e 40 40
IIH Vee = 5.5 V, VI = 2.7 V p.A
-
All others 20 20
A, B, or e -0.6 -0.6
IlL Vee = 5.5 V, VI = 0.4 V
-0.3
rnA
All others -0.3
IOf Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V, 26 26 rnA
J>
r- tAli typical values are at Vee = 5 V, TA = 25°e.
o *The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS'
J> switching characteristics (see Note 1)

Z
C Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
J> FROM TO Rl = 500O,
o PARAMETER
UNIT
Q SN54AS151 SN74AS151
:a MIN Typt MAX MIN Typt MAX

(') tpLH y
5 5
ns
c tpHL
A, B, or e
5 5
=t
o
tpLH
tPHL
A, B, or e w 4.5
4.5
4.5
4.5
ns
tPLH 3 3
Any D Y ns
tpHL 4 4
tpLH 3 3
Any D W ns
tpHL 2.5 2.5
tpLH 5 5
G Y ns
tpHL 5 5
tpLH 4.5 4.5
G W ns
tpHL 4.5 4.5

PRODUCT PREVIEW 12
2 -1 24
ThIs page contains Information on a product under
development. Te ••• InSlnlments ..saIV.. the right to TEXAS
chenge or discontinue this product without notice. INSTRUMENTS
DUAL 1 OF 4 DATA SELECTORS/MULTIPLEXERS
• Permits Multiplexing from N Lines to 1 Line

• Performs Parallel-to-Serial Conversion SN54ALS153, SN54AS153. • J PACKAGE
SN74ALS153, SN74AS153. . N PACKAGE
• Strobe (Enable) Line Provided for Cascading (N
(TOP VIEW)
lines to n lines)
• Fully Compatible with Most TTL Circuits
1G :: 1 U16 VCC
• 'ALS253 and 'AS253 Are 3-State Versions of B 2 15 2(3
These Parts 1C3 3 14 A
• Package Options Include Both Plastic and Ceramic 1C2 4 13 2C3
Chip Carriers in Addition to Plastic and Ceramic 1C1 5 12 2C2
DIPs 1CO 6 11 2C1
1Y 7 10F 2CO
• Dependable Texas Instruments Quality and GND 8 9 2Y
Reliability
description
SN54ALS153,SN54AS153. FH PACKAGE
Each of these data selectors/multiplexers contains
SN74ALS153,SN74AS153 . FN PACKAGE
inverters and drivers to supply full binary decoding data
(TOP VIEW)
selection to the AND-OR gates. Separate strobe inputs (G)
are provided for each of the two four-line sections.
U
The SN54ALS153 and SN54AS153 are characterized for 1C!l U UIC!l
operation over the full military temperature range of CO'-Z>N
-55°C to 125°C. The SN74ALS153 and SN74AS153

are characterized for operation from 0 °C to 70°C. 1C3 A
1C2 2C3
NC NC
1C1 2C2 en
1CO 2C1 t::
:l
U
FUNCTION TABLE >-OU>-O
'-ZZNU
N
a::
C!l
SELECT
DATA INPUTS STROBE OUTPUT U
INPUTS
B A CO C1 C2 C3 y NC - No internal connection en
X X X X X X
G
H L
<t
L ~ L X X X L L logic symbol C
L L H X X X L H 2
L H X L X X L L <t
H
L H
L
X
X
H
X
X
L
X
,X
L
L
H
L
en
...J
H L X X H X L H <t
H H X X X L L L
H H X X X H L H
Select inputs A and B are common to both sections.

3
TEXAS 2-125
INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEXAS 75265-,
1 CO ...;..;16..;..1_ _ _ _ _ _ _ _ _+-+-+-"--J
lCl ~1~51~__________~~=t~L-~
OUTPUT
lY
DATA 1
..
l>
r-
en
SelECT
2CO
A
1101
1111
l>
z
c DATA 2 OUTPUT
2Y
l>
en
Q
::D
(")
c
=i
en
Supply voltage, Vee .............................................................. 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 53, SN54AS153 . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS153, SN74AS153 . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . , . . . . . . .. - 65 °e to 150 °e
2-126 TEXAS
INSTRUMENTS

UNIT
PARAMETER I TEST CONDITIONS UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V 10L = 24 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V, All inputs at 4.5 V 7.5 14 7.5 14 mA

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS. en
t::
::)
(.)
ex:
(J
Vcc = 4.5 V to 5.5 V,
en
PARAMETER
FROM TO
CL
RL
= 50 pF,
= 500 n,
UNIT
«
(INPUT) (OUTPUT) TA = MIN to MAX c
SN54ALS153 SN74ALS153 z
MIN
5
MAX
25
MIN
5
MAX
21
«
tpLH
tpHL
A or B Y
5 25 5 21
ns en
-J
tpLH
tpHL
Data (Any e) y
3
4
12
18
3
4
10
15
ns «
tpLH 5 22 5 18
G Y ns
tpHL 5 22 5 18
13
TEXAS 2-127
INSTRUMENTS

SN54AS153 SN74AS153
UNIT
SN54AS153 SN74AS153
VIK Vee = 4.5 V. II =
-18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. IOH = -2 mA Vee- 2 Vee- 2
VOH Vee - 4.5 V. IOH - -12 mA 2.4 3.2 V
Vee = 4.5 V. IOH = -15 mA 2.4 3.3
Vee = 4.5 V. IOL = 32 mA 0.25 0.5
VOL V
Vee'" 4.5 V IOL = 48 mA 0.35 0.5
A. B 0.2 0.2
II Vee = 5.5 V. VI = 7 V mA
A" others 0.1 0.1
A. B 40 40
IIH Vee = 5.5 V. VI = 2.7 V p.A
A" others 20 20
A. B -1 -1
IlL Vee = 5.5 V. VI = 0.4 V mA
A" others -0.5 -0.5
loi Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V. I Outputs high 16 26 16 26

mA
I Outputs low 21 33 21 33
t All typical values are at Vee = 5 V. TA = 25 DC.

Vcc = 4.5 Vto 5.5 V.

CL = 50 pF.
PARAMETER
FROM TO RL = 500 n.
UNIT
SN54AS153 SN74AS153
MIN MAX MIN MAX
tpLH 3 14 3 12.5
A or B Y ns
tpHL 3. 12.5 3 11
tpLH 2 8 2 7
Data (Any e) y ns
tpHL 2 8.5 2 8
tpLH 3 13 3 11.5
G Y ns
tpHL 2 10 2 9
NOTE 1: For load circuit and voltage waveforms. see page 1·12.
12
2-128 TEXAS
INSTRUMENTS
POST OF F ICE BOX 2250 12 • DALLAS, TEXAS 75265
TYPES SN54ALS157, SN54ALS158, SN54AS157, SN54AS158
SN74ALS157, SN74ALS158, SN74AS157, SN74AS158
QUADRUPLE 1 OF 2 DATA SELECTORS/MULTIPLEXERS
• Buffered Inputs and Outputs

SN54ALS', SN54AS' ..• J PACKAGE
• Package Options Include Both Plastic and SN74ALS', SN74AS' ••• N PACKAGE
Ceramic Chip Carriers in Addition to Plastic and (TOP VIEW)
Ceramic DIPs
AlB Vee
Reliability
1A G
1B 4A
description 1Y 4B
2A 4Y
These monolithic data selectors/multiplexers contain
2B 3A
inverters and drivers to supply full data selection to 2Y 3B
the four output gates. A separate strobe input (<3) is
GND 3Y
provided. A 4-bit word is selected from one of two
sources and is routed to the four outputs. The
'ALS157 and 'AS157 present true data whereas the SN54ALS', SN54AS' ..• FH PACKAGE
'ALS 158 and 'AS 1 58 present inverted data to SN74ALS', SN74AS' ••. FN PACKAGE
minimize propagation delay time. (TOP VIEW)
The SN54' family is characterized for operation over
the full military temperature range - 55 °e to 125 °e.
The SN74' family is characterized for operation from
ooe to 70 oe.
4A
logic symbols
4B
'ALS157, 'AS157 NC
4Y
3A
CI)
1V ~
:::l
2Y
NC - No internal connection U
3Y
a:
U
4Y
FUNCTION TABLE CI)
INPUTS OUTPUT Y <C
STROBE SELECT
DATA
'ALS157 'ALS158 c
'ALS158, 'AS158 G AlB A B 'AS157 'AS158 z
H X X X L H <C
L L L X I., .H CI)
L L H X H L ....I
L H X L L H <C
1Y L H X H H L
2Y
3Y
4Y

:3
TEXAS 2-129
INSTRUMENTS
TYPES SN54ALS157, SN54ALS158, SN74ALS157, SN74ALS158
.QUADRUPLE 1 OF 2 DATA SELECTORS/MULTIPLEXERS
• logic diagrams (positive logic)

'ALS157
(2)
1A------------------------~
1B~(~3)----------------~~--,
(5)
2A------------------~~+_~~
(6)
2B------------------~~+_~
(111
3A------------------~~+_~
3B (10)
(14)
4A--------------------r-+-,
(13)
4B------------------~~+_~
STROBE G _(_15_)_____-.----<01
SELECT AlB ....;(..;.;,11---4.-____1--..0
EI
»
r
(2)
1A----------------------~~
'ALS158
tn
»
Z
1B (3)
C (5)
»
tn
2A------------------~--+_~
2B (6)
Q
:Jl (11)
n 3A------------------r-+~
c
=i (10)
3B------------------~--+_~~
tn
(14)
4A----------------~-+~
(13)
4B------------------~--+_~
STROBE G _(_15_)______-*~:>I
SELECT AlB _(_1)---4I---~--a
121
2-130 TEXAS
INSTRUMENTS
POST OFFiCE BOX 225012 • DALLAS. TEXAS 75265
TYPESSN54AS157, SN54AS158, SN74AS157, SN74AS158
QUADRUPLE 1 OF 2 DATA SELECrORS/MULTIPLEXERS
logic diagrams (positive logic)

1A ...:.;(2;.;..)_ _ _ _ _ _ _ _ _ _-f-~
1B ~(3~)___________+_~--~
2A ~(5~)_ _ _ _~--~_+___+--t .
2B ...:.;(6;.;..)_ _~_ _ _ _ _ _~_+~~
3A (11)
3B (10)
4A (14)
4B~(1~3~)____________-+~--~.
1A
(2)
'AS158
..
en
t::
::J
(3)
1B U
a:
2A
(5) U
en
(6) <t
2B
.0
;2
(11)
3A <t
(10)
en
-I
3B
<t
4A (14)
(13)
4B
83
TEXAS 2-131
INSTRUMENTS
QUADRUPLE 2·LlNE TO 1·LlNE DATA SELECTORS/MULTIPLEXERS
Supply voltage, Vee .. ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS157, SN54ALS158 . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS157,SN74ALS158 . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " - 65 °e to 150 °e

SN54ALS158 SN74ALS158 UNIT
TA Operating free-air temperature -55 125 a 70 °e
SrJ54ALS157 SN74ALS157
PARAMETER TEST CONDITIONS SN54ALS158 SN74ALS158 UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
:t> Vee = 4.5 V to 5.5 V, IOH = -0.4 mA vee- 2 Vee- 2
r-
en VOH Vee
Vee
= 4.5
= 4.5
V,
V,
10H = -1 mA
IOH = -2.6 mA
2.4 3.3
2.4 3.2
V
:t> Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4

V
2 VOL
Vee = 4.5 V 10L = 24 mA 0.35 0.5
C II Vee = 5.5 V, ,VI = 7 V 0.1 0.1 mA
:t> IIH Vee = 5.5 V, VI = 2.7 V 20 20 I'A

en IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
10:1= Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
("),
I 'ALS157 7.8 7.8
II ICC I 'ALS158 Vee = 5.5 V, mA
2.3 2.3
(")
C tAli typical values are at Vee = 5 V, TA = 25°e.
==i ~The output conditions have b~en chosen to produce a current that closely approximates one half of the true short-circuit current, lOS'
en
ADVANCE INFORMATION 128

This page contains Information on 8 new product.
2-1 32 Specifications ara subject to change without notics. TEXAS
INSTRUMENTS
TYPES SN54ALS157. SN54ALS158. SN14ALS151, SN14ALS158
QUADRUPLE '1 OF 2 DATA SELECTORS/MULTIPLEXERS
, . ' . " ••. '.,:,;.' 1'- . • . • . •
, ALS 157 switching characteristics (see Note 1)
. vee = 4.5 V to 5.~ V,

Cl = 51) pF,
FROM TO RL = 500 Q,
PARAMETER UNIT
(INPUT) (OUTPUT) TA";' MIN to MAX
SN54AlS157 '. SN74AlS157'
MIN TypT MAX MIN TYpr MAX
tpLH 3.5 3.5
'A or B Y ns
tpHL 5 5
tpLH 6 6
AlB y ns,
tPHL 6.5 . 6.5
tpLH 6 6
G y os
tpHL 6.5 6.5
Vec = 4.5 V to 5.5 V,

Cl = 50 pF,
..
FROM TO Rl = 5~0 Q~
PARAMETER UNIT
MIN TYpt MAX MIN TYpt' MAX
tpLH . 3.5 3.5
A or B Y ns
tpHL 5 5
en
tpLH
AlB y 6 6
ns l-
tpHL
tpLH
6.5
6
6.5.
6
S
G y ns (.)
tpHL 6.5 6.5 a:
tAli typical values are at Vee = 5 V, TA = 25°C. o
NOTE 1: For load circuit and voltage waveforms, see page 1·12.
en
«
c
2:
«
en
..J
«
83 ADVANCE INFORMATION
Speclficatlona Br. subject to change without notice. TEXAS 2-133
INSTRUMENTS
TYPES SN54AS157. SN54AS158. SN74AS157. SN74AS158
QUADRUPLE 1 OF 2 DATA SELECTORS/MULTIPLEXERS
Supply voltage, Vee '.' ............................................................... 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54AS157, SN54AS158 ..................... -55°e to 125°e
SN74AS157, SN74AS158 ......................... oDe to 70 0 e
Storage temperature range. . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e

SN54AS157 SN74AS157
SN54AS158 SN74AS158
UNIT
V,H High.levei input voltage 2 2 V
V,L Low-level input voltage 0.8 0.8 V
SN54AS157 SN74AS157
PARAMETER TEST CONDITIONS SN54AS158 SN74AS158 UNIT
V,K Vee = 4.5 V, " = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, IOH = -2mA vcc- 2 vcc- 2 V
VOL Vee = 4.5 V, 'OL = 20 mA 0.35 0.5 0.35 0.5 V
AlB 0.2 0.2
Vee = 5.5 V. V, = 7 V mA
"
A. B. or G 0.1 0.1
AlB 40' 40
"H Vee = 5.5 V, V, = 2.7 V JlA
A. B. or G 20 20
AlB -1 -1
',L Vee = 5.5 V. V, = 0.4 V mA
A. B or G -0.5 -0.5
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
'AS157 17.5 28 17.5 28
lee Vee = 5.5 V. mA
'AS158 15.6 22.5 15.6 22.5
t All typical values are at VCC ; 5 V. TA ; 25°C.

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit current. lOS'
12f
2-134 TEXAS
INSTRUMENTS
TYPES SN54AS157, SN54AS158, SN74AS157, SN74AS158
QUAD~UPLE 1 OF" 2D~TA ,SELECTORS/MULT,IPLEXERS
"AS157,sw!tching cha.racteristics (see Note 1) ,

Vcc = 4.5 V to5.5'V.
CL = 50 pF.
FROM TO RL =5000.
PARAMETER UNIT
(lNPUTI (OUTPUT! TA =; MIN to MAX
SN54AS157 SN74AS157
MIN MAX MIN MAX
tpLH y 1 7.5 1 6
A or B ns
tPHL 1 6.5 l' ,5.5
tpLH 2 12 .2 11
AlB. y ns
tpHL 2 12. 2 10
tpLH 2 12.5 2' 10.5
G y ns
tpHL 2 8.5 2 7.5
'AS 158 switching characteristics (see Note 1),

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 O.
PARAMETER UNIT
(lNPUTI (OUTPUTI TA = MIN to MAX
SN54AS158 SN74AS158
MIN MAX MIN MAX
tpLH 1 6 1 5
A or B Y ns
tpHL 1 5.5 1 ' 4.5
tpLH '2 11 2 9.5
AlB Y ns
tpHL 2 11.5 2 10.5
tpLH 2 8 2 6.5
G Y ns
tpHL 2 11.5 2 10
283
TEXAS 2-135
INSTRUMENTS
- >
r-
en
>
2:
C
>
en
o
:xJ
o
c
=i
CA
2-136
TYPES SN54ALS160A THRU SN54ALS163A, SN54AS160 THRU SN54AS163
SrJ74ALS160A THRU S~J74ALS163A, SN74AS160 THRU SN74AS163
SYNCHRONOUS 4·BIT DECADE AND BINARY COUNTERS
02661, AP~IL 1982-REVISED DECEMBER 1983
o Internal Look·Ahead for Fast Counting SN54ALS', SN54AS' , .. J PACKAGE

SN74ALS', SN74AS' ... N PACKAGE
o Carry Output for n·Bit Cascading (TOP VIEW)
o Synchronous Counting
CLR VCC
o Synchronously Programmable CLK RCO
A OA
B OB
Ceramic Chip Carriers in Addition to Plastic and
C Oc
Ceramic DIPs
D OD
o Dependable Texas Instruments Quality and ENP ENT
Reliability GND LOAD
description
SN54ALS·. SN54AS ... FH PACKAGE
These synchronous, presettable counters feature an internal carry
SN74ALS'. SN74AS' ... FN PACKAGE
look-ahead for application in high-speed counting designs. The (TOP VIEW)
'ALS 160A, 'ALS 162A, 'AS 160, and 'AS 162 are decade
counters, and the' ALS 161 A, 'ALS 163A, 'AS 161 , and 'AS 163 Uo
::<:ICX:
uu
...J...J U
are 4-bit binary counters. Synchronous operation is provided by uuz>cx:
having all flip-flops clocked simultaneously so that the outputs
change coincident with each other when so instructed by the A
count-enable inputs and internal gating. This mode of operation B
eliminates the output counting spikes that are normally associated NC
with asynchronous (ripple clock) counters. A buffered clock input C
triggers the four flip-flops on the rising (positive-going) edge of D
the clock input waveform.
These counters are fully programmable; that is, the outputs may n. U0 10
Zzz<x:
w~ OW
I-
Z
be preset to either level. As presetting is synchronous, setting
up a low level at the load input disables the counter and causes
...J en
the outputs to agree with the setup data after the next clock pulse NC - No internal connection !::
::>
regardless of the levels of the enable inputs.
u
The clear function for the' ALS 160A, 'ALS 161 A, 'AS 160, and' AS 161 is asynchronous and a low level at the clear a:
input sets all four of the flip-flop outputs low regardless of the levels of the clock, load, or enable inputs. u
The clear function for the 'ALS162A, 'ALS163A, 'AS162, and 'AS163 is synchronous and a low level at the clear en
input sets all four of the flip-flop outputs low after the next clock pulse, regardless of the levels of the enable inputs. «
This synchro'nous clear allows the count length to be modified easily as decoding the maximum count desired can
c
be accomplished with one external NAND gate. The gate output is connected to the dear input to synchronously
z
clear the counter to 0000 (LLLL).
«
The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without additional en
gating. Instrumental in accomplishing this function are two count-enable inputs and a ripple carry output. Both count- ..J
enable inputs (ENP and ENT) must be high to count, and ENT is fed forward to enable the ripple carry output. The
ripple carry output (RCO) thus enabled will produce a high-level pulse while the count is maximum (9 or 1 [) with OA
«
high). This high-level overflow ripple carry pulse can be used to enable successive cascaded stages. Transitions at
the ENP or ENT are allowed regardless of the level of the clock input.
These counters feature a' fully independent clock circuit. Changes at control inputs (ENP, ENT, or LOAD) that will
modify the operating mode have no effect on the contents of the counter until clocking occurs. The function of the
counter (whether enabled, disabled, loading, or counting) will be dictated solely by the conditions meeting the stable
setup and hold times.
The SN 54ALS 1 60A through SN 54ALS 163A and SN 54AS 160 through SN 54AS 163 are characterized for operation
over the full military temperature range of -55 DC to 125 DC. The SN74ALS160A through SN74ALS163A and
SN74AS160 through SN74AS163 are characterized for operation from ODC to 70 DC.
TEXAS 2-137
INSfRUMENTS
TYPES SN54ALS160A, SN54ALS162A, SN54AS160, SN54AS162
SN74ALS160A, SN74ALS162A, SN74AS160, SN74AS162
SYNCHRONOUS 4·811 DECADE COUNTERS· .
logic symbols
'AlS160A AND 'AS160 DECADE 'AlS162A AND 'AS162 DECADE
COUNTERS WITH DIRECT CLEAR COUNTERS WITH .sYNC~RONOUS CLEAR
CTRDIV10
m
U5'AD
RCO
ENT ENT
ENP ENP
ClK - - - 0 ClK
A A OA
B B °B
C C Oc
D D aD
'ALS160A and 'AS160 logic diagram (positive logic)

Ci:R( 11
LOAi5 (9)
ENT ~ (15)
ENP
(7) 1 ....... RCO
ClK
(2)~~
.-----
IB >--C~C1 ~
~
--c1D
l> A
(3) ~~~
r0-
tA
~
l>
2 .---
C ...--ct>C1 ~
l>
fA (4)
>-~~
Q
B
---
....---:..
::rJ ~1-<~C1 ~
~
~I-
n - f-I-< 10
c: C
(5)
-,--,
~~~
~
(J) '1
~
f=::=D'L }-
~f<~
I-<
>- ~
1D
__ ~R P-
(6) }- i..-..-
D
'ALS~62A and 'AS162 decade counters are similar; however the clear is synchronous as shown for the 'ALS163A and 'AS163 binary counters.
128:
2-138 TEXAS
INSTRUMENlS
SYNCHRONOUS 4·81T DECADE COUNTERS
logic symbols
'ALS161A AND 'AS161 BINARY 'ALS163A AND 'AS163 BINARY
COUNTERS WITH DIRECT CLEAR COUNTERS WITH SYNCHRONOUS CLEAR
CLR
L5'Ao
(15)
RCO 3CT=15 RCO
ENT ENT
ENP ENP
ClK ClK
(14)
A A OA
B B OB
C C Qc
o 0 Qo
'ALS163A and 'AS163 logic diagram (positive logic)
en
(14)
°A
t:
=>
A (3) U
a:
U
(13) 0B
en
B (4)
«
C
Z
«
(12) Oc
en
..J
C (5) «
(11)
CD
o (6)
'ALS 161 A and' AS 161 synchronous binary counters are similar; however the clear is asynchronous as shown for the' ALS 160A and 'AS 160 decade counters.
283
TEXAS 2-139
INSfRUMENTS
SYNCHRONOUS 4·BIT BINARY COUNTERS
typical clear, preset, count, and inhibit sequences
'ALS160A, 'AS160, 'ALS162A, 'AS162
Illustrated below is the following sequence:

1. Clear outputs to zero ('ALS160A and 'AS160 are asynchronous; 'ALS162A and 'AS162 are synchronous)
2. Preset to BCD seven
3. Count to eight, nine, zero, one, two, and three
4. Inhibit
IOA5 U
A-.J
L=
DATA
B-.J
L=
INPUTS
c-.J
c=
,--
I
..
D
ClK
ENP
II
»
r-
en
ENT
I I
:I
»
2 °A
--,I -,I
-! - I
I I I
C -.
-! i---.JI
I I I
·1
»
en
°B
I I I
--, --1
OUTPUTS
I I
C') °c -! _I---.JI
I I
~ -, -, I I
C') °D
'-"j
I
- I I
C I I I
I
I
I
=4 RCO
I
I
I
_____~~---~_+---~r--l~--------~-----------------
I I
I
I
tn I
I :7 :8I
I o
I
9 2 3
I I· I...
...- - - - C O U N T - - - - - ·.. · - - - - I N H I B I T - - - - -
I SYNC
CLEAR
I PRESET
ASYNC
CLEAR
128:
2-140 TEXAS
INSTRUMENlS
SYNCIiRONOUS 4·81T DECADE COUNTERS
typical clear. preset. count. and inhibit sequences
'ALS161A, 'AS161, 'ALS163A, 'AS163

I. Clear outputs to zero ('ALSI6IA and 'AS161 are asynchronous; 'ALSI63A and 'AS163 are synchronous)
2. Preset to binary twelve
3. Count to thirteen, fourteen, fifteen, zero, one, and two
4. Inhibit
ClR~
I
I
lOAD I
I U
I
r-
DATA
INPUTS
A
B
I
.-
I
i
C--.l L_
...---,.
I
D-.J L_
ClK
ENP ~ _ _ _ _ _---.J
en
ENT
C
I
I ::>
QA
-, --,,
I
u
.-!. a:
QB
-, --, u
--'. en
OUTPUTS
-, --,~
<t
Qc ---1 _,
I c
-, I
z
--l. ;--.--J <t
QD
I I I
RCO ____~~I I en
__~________~r--l~______~_________________ ..J
I I
I
I
:12 13 14 15 0 2, <t
~
I
SYNC PRESET
I-
_ - - - - C O U N T - - - -....
I_----INHIBIT---_
CLEAR
ASYNC
CLEAR
~83
TEXAS 2-141
INSTRUMENTS
TYPES SN54ALS160A THRU SN54ALS163A
SN74ALS160A THRU SN74ALS163A
Supply voltage, Vee ................................................................ , 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS160A thru SN54ALS163A . . . . . . . . . . . . .. - 55 °e to 125°C
SN74ALS160A thru SN74ALS163A .................. O°C to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150°C

THRU THRU
SN54ALS163A SN74ALS163A UNIT
CLK high or low 20 16.5
tw Pulse duration ns
'ALS160A, 'AlS161A, CLRlow 20 15
A, B, C, D 20 15
LOAD 20 15
I'AlS160A, 'ALS161A
-
25 2.0
Setup time ENP, ENT
tsu l'ALS162A, 'AlS163A 30 25 ns
before ClKt
'AlS160A, 'ALS161A CLR inactive 10 10
20 15
II
'ALS 162A, 'ALS 1 63A CLR low
.ClR high (inactive) 10 10
:t> th Hold time, all synchronous inputs after ClKt 0 0 ns
r- TA Operating free-air temperature -55 125 0 70 °c
m
:t> electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
2 SN54AlS160A SN74ALS160A
C THRU THRU
:t> SN54ALS163A SN74ALS163A
m MIN Typt MAX MIN Typt MAX
VCC = 4.5 V, ·11 = -18 mA -1.5 -1.5 V
Q VIK
VCC = 4.5 V to 5.5 V, IOH = -0.4 mA vee- 2 vee- 2 V
VOH
::c
o VOL
VCC = 4.5 V, IOl = 4 mA 0.25 0.4 0.25 0.4
V
c VCC = 4.5 V, IOl = 8 mA 0.35 0.5
=i II
lOAD, ClK or ENT
VCC = 5.5 V, VI': 7 V
0.2 0.2
rnA
m All other
lOAD, ClK or ENT
0.1
40
0.1
40
'IH VCC = 5.5 V, V, = 2.7 V p.A
All other 20 20
I,l VCC = 5.5 V, V, = 0.4 V -0.2 -0.2 rnA
RCa -15 -70 -15 -70
IO~ VCC = 5.5 V, Va ,;, 2.25 V rnA
Q -30 -112 -30 -112
ICC VCC = 5.5 V 12 21 '12 21 rnA

tThe output conditions have been chosen to prod~ce a current that closely approximates one half of the true short·circuit output current, lOS'
12E
2-142 TEXAS
INSTRUMENlS
'ALS160A, 'ALS161A switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 500 n.
FROM TO
PARAMETER TA = MIN to MAX· UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX
f max 25 30 MHz
tplH 8 30 8 26
ClK RCO ns
tpHl 7 25 7 23
tplH 4 18 4 15
ClK Any Q ns
tPHl 6 20 6 17
tplH 3 16 3 13
ENT RCO ns
tpHl 3 16 3 13
tpHl ClR Any Q 8 27 8 24 ns
tpHl ClR RCO 11 31 11 28 ns
, ALS 162A, 'ALS 163A switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
Rl = 500 n.
FROM TO
PARAMETER TA = MIN to MAX UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX
f max 25 30 MHz en
tplH
ClK RCO
8 30 8 26
ns
~
tpHl 7 25 7 23 :::>
tplH 4 18 4 15 u
tpHl
ClK Any Q
6 20 6 17
ns a::
tplH
ENT RCO
3 20 3 17
ns
U
tpHl 3 16 3 13
en
• NOTE 1: For'load circuit and voltage waveforms. see pa~e 1·12. «
c
z
«
en
...J
«
TEXAS 2-143
INSTRUMENTS
TYPES SN54AS160 THRU SN54AS163
SN74AS160 THRU SN74AS163
absolute maximum ratings over operating free~air temperature range (unless otherwise noted)
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54AS160 thru SN54AS163 ... . . . . . . . . . . . . . .. - 55°C to 125°C
SN74AS160 thru SN74AS163 ... " ... , ..... , ....... ooe to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150 °e

SN54AS160 SN74AS160
THRU THRU
SN54AS163 SN74AS163 UNIT
fclock Clock frequency MHz
ClK high or low
'AS160, 'AS161 ClR low
..
A, B, C, D
lOAD
Setup time ENP, ENT
tsu ns
before ClKt 'AS160, 'AS161 elR inactive
'AS162, 'AS163
I elR low
IClR high (inactive)
l> th Hold time, all synchronous inputs after ClK t ns
r- TA Operating free-air temperature -55 125 0 70 °e
til
l>
~ electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54AS160 SN74AS160
l> THRU THRU
til PARAMETER TEST CONDITIONS
SN54AS163 SN74AS163
UNIT
MIN Typt MIN Typt

s:2 VIK Vce 4.5 V, II = -18 mA
MAX
-1.2
MAX
1.2 V
::D =
o VOH Vce = 4.5 V to 5.5 V, IOH = -2 mA Vee- 2 vee- 2 V

c: VOL Vee = 4.5 V, IOl = 20 mA 0.25 0.5 0.25 0.5 V
=i II Vee
Vec
= 5.5
= 5.5
V,
V,
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
mA
p.A
til IIH
III
I lOAD, ENT Vce = 5.5 V, VI = 0.4 V
-1 -1
mA
I All other -0.5 -0.5
lOt Vce = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lec Vee = 5.5 V 40 40 mA
* All typical values are at Vee = 5 v, T A = 25°C.

*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
PRODUCT PREVIEW 12i

2-144
Thl. page contains Informetlon on a product under
devalopment. T..... ln.trument..... rv.. therlghtto TEXAS
. chenge or dl.contlnu. this product without notice.
INSTRUMENTS
'AS160, 'AS161 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
Rl = 500 n.
FROM· TO
(INPUT) (OUTPUT)
SN54AS160 SN74AS160
SN54AS161 SN74AS161
MIN TYpt MAX MIN Typt MAX
f max MHz
tplH RCO 7 7
tpHl ClK RCO (with lOAD high) 6 6 ns
tpHl RCO (with lOAD low) 10 10
tplH 5 5
ClK Any Q ns
tpHl 6 6
tplH 3 3
ENT RCO ns
tPHl 4 4
tpHl ClR Any Q 7 7 ns
•AS 162 •• AS 163 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
Rl = 500 n.
FROM TO
(INPUT) (OUTPUT)
SN54AS162 SN74AS162
SN54AS163 SN74AS163 en
MIN Typt MAX MIN Typt MAX t:
f max MHz ::l
tplH RCO 7 7 (.)
tpHl ClK RCO (with lOAD high) 6 6 ns a:
tPHl RCO (with lOAD low) 10 10 C3
tplH
ClK Any Q
5 5
ns en
tpHl
tPlH
6
3
6
3
<t
tPHl
ENT RCO
4 4
ns
c
tpHl ClR Any Q 7 7
z
<t
Vee =
5 V. TA = 25°C.
t All typical values are at
NOTE1: For load circuit and voltage waveforms. see page 1-12. en
....I
Additional information on these products can be obtained from the factory as it becomes available. <t
33 PRODUCT PREVIEW
development. Tex.. Instruments reserve. the right to
change or discontinue this product without notice.
TEXAS 2-145
INSTRUMENTS
POST OFFiCE BOX 225012 • DALLAS, TEXAS 75265
SN74ALS160A THRU SN74ALS163A, SN74AS160 THRU SN74AS163
TYPICAL APPLICATION DATA
N·BIT SYNCHRONOUS COUNTERS
This application demonstrates how the look-ahead carry circuit can be used to implement a high-speed n-bit counter. The
'ALS160A, 'AS160, 'ALS162A, and 'AS162 will count in BCD and the 'ALS161A, 'AS161, 'ALS163A and 'AS163 will
count in binary. Virtually any count mode Imodulo-N, Nl-to-N2, Nl-to-maximum) can be used with this fast look-ahead circuit.
lSB
.ClEAR (ll ern"" CT=O CTR

LIDrn ,...." M1
COUNT (HI AND ENT RCO
G3 3CT=MAX ~
DISABLE (ll ENP
G4
ClK
., C5/2.3,4+
I'"
A - 1,50 111 r--°A
LOAD (LI
B- (21 r--OB
C- (31 r--Oc
COUNT (HI ~ 0- (41 "'--- 00
~.
DISABLE (l I
----1_ ern,....... CT=O CTR

CLOCK
IOAli ,...." M1
~
ENT
G3 3CT=MAX
ENP
G4
ClK
., C5/2,.3,4+
r
A - 1,50 (11 -OA
B- (21 -OB
C- (31 -Oc
0- (41 -00
ern"" CT=O
CTR
lOAD " " M1
ENT
ENP
G3
G4
3CT=MAX - RCO
ClK
C5/2,3,4+
"1 r
A - 1,50 (11 r--OA
B- (21 I--°B
C- (3) I--Oc
0- f41 1-- 0 0
CLR ,.... CT=O CTR

LOAD ,....
M1
ENT RCO
G3 3CT ~MAX I---
ENP
G4
CLK
t:; C5/2,3,4+
r
A - 1,50 (11 I--OA
B- (21 I - - OB
C- (31 I-- Oc
D- (4) 1-- 0 0
~------------~v~------------·
TO MORE SIGNIFICANT STAGES
121
2-146 TEXAS
. INSTRUMENTS
POST OFFICE BOX 225012 • OALLAS. TEXAS 75265.
8·BIT PARALLEL·OUT SERIAL SHIFT REGISTERS
02661. APRil 1982-REVISED DECEM8ER 1983
• AND-Gated (Enable/Disable) Serial Inputs SN54ALS164 • . . J PACKAGE

SN74ALS164 . . . N PACKAGE
• Fully Buffered Clock and Serial Inputs (TOP VIEW)
• Direct Clear
A VCC
o Package Options Include Both Plastic and Ceramic B OH
°A OG
• Dependable Texas Instruments Quality and Reliability OB OF
Oc OE
description OD ClR
GND ClK
These 8-bit shift registers feature AND-gated serial inputs and an
asynchronous clear. The gated serial inputs (A and B) permit
complete control over incoming data as a low at either input
inhibits entry of the new data and resets the first flip-flop to the SN54ALS164 • . . FH PACKAGE
low level at the next clock pulse. A high-level input enables the SN74ALS164 . . . FN PACKAGE
other input, which will then determine the state of the first flip- (TOP VIEW)
flop. Data at the serial inputs may be changed while the clock is
high or low, provided the minimum setup time requirements are u
u u::c
met. Clocking occurs on the low-to-high-Ievel transition of the CO«Z>O
clock input. All inputs are diode-clamped to minimize
transmission-line effects.
The SN54AlS164 is characterized for operation over the full

military temperature range of - 55 °C to 125°C. The
SN7 4AlS 164 is characterized for operation from 0 °C to 70 °C.
00 U
OZZ-l-l
10:
:.::: tJ)
t!) UU
!::
NC-No Internal connection :::>
u
a:
INPUTS
FUNCTION TABLE
OUTPUTS
logic symbol u
tJ)
CLEAR
L
CLOCK
X
A
X X
B OA
L
0B·· .OH
L L
CLR
«
H L X X °AO aBO °HO ClK c
H t H H H OAn OGn 2
H
H
t
t X
L X
L
L
L
QAn
OAn
QGn
OGn
A
B
«
tJ)
...J
H ; high level (steady state). l ; low level (steady state)
X ;
t ;
irrelevant (any input. including transitions)
transition from low to high level.
«
0AO. 080. 0HO = the level of 0A. 08. or 0H. respectively. before the
indicated steady-state input conditions were established.
0An. 0Gn ; the level of 0A or 0G befor~ the most·recent t transition
of the clock; indicates a one-bit shift.
Pin numbers shown are for J and N packages..
PRODUCT PREVIEW Copyright © 1982 by Texas Instruments Incorporated

83
discontinue this product without notice. POST OFFICE BOX 225012 • DALLAS. TEXAS 75265
8·BIT·PARALLEL·OUT SERIAL SHIFT REGISTERS

(9)
CLOCK_I_8)____~~~--~--~--~--~--_+-- __
CLEAR------~~~~--__- - - - - -__------~------~------~------~------~------~
--~-- __ --~-- __ --_+--__~~~_,
(3) (4) (5) (6) (10) (11) (12) (13)
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT

oA oB oc 00 oE OF oG oH
typical clear, shift, and clear sequences
CLEAR~
I
I
SERIAL {
INPUTS
A ~----------~---------
-~~---- .....
~ CLOCK 1
1
---,__________
1
°A ___
l> ~~------~---------
~' ~
r-
en °B ---,
___ . . '.____________. . .
~~----~---------
l> OC===~J_______________~
2
o ~~------------
Oil ==-J...J..-_______________---'
l> ~~,----------
en
[)LJTPUTS
---,
O[ ___ ~, __________________ LJlL......-..-____ ~
I
o ---,
°f ___ . . . ___________________ , 1
::D
'~ ~
I
o °G ===.l. ._______________________
C ....-J
~
I
en ---,. .,.________________________
°H __ ~n' ________
~
CLEAR
I
CLEAR
Supply voltage, Vee . , ' , ' , , ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS164 . . . . . . . . . . .' . . . . . . . . . . , . . . . . . . - 55 °e to 125 °e
SN74ALS164 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . " - 65 °e to 150 0 e
12:
2-148 TEXAS
INSTRUMENTS
8·HIT·PARALLEL·OUT SERIAL SHIFT REGISTERS
UNIT
CLR low
tw Pulse duration CLK high ns
CLK low
SH/LD
Setup time
tsu Data ns
before CLKI
CLR inactive
th Hold time, data after' CLK I 10 0 ns
TA Operating free-air temperature - 55 125 0 70 °c
PARAMETER TEST CONDITIONS ,UNIT
VIK Vce = 4.5 V, II = -18 rnA -1.5 -1.5 V
VOH Vce = 4.5 V to 5.5 V, IOH = -0.4 rnA Vee- 2 Vee- 2 V
VCC - 4.5 V, IOL - 4 rnA 0.25 0.4 0.25 0.4
VOL V
Vce = 4.5 V, IOL = 8 rnA 0.35 0.5
II Vce = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH VCC = 5.5 V, VI = 2.7 V 20 20 p.A CJ)
IlL VCC = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA ....
IO:/: VCC = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
=>
ICC VCC = 5.5 V See Note 1 10 10 rnA U
t All typical values are at Vee = 5 v, TA = 25°C.
a:
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS. U
NOTE 1: With 4.5 Volts applied to the serial input and all other inputs except the clock grounded, ICC is measured after a clock transition from 0 to 4.5 volts.
CJ)
switching characteristics (see Note 2) <C
Vcc = 4.S V to S.S V, C
CL = SO pF, :2
FROM TO RL = 500 fI, <C
PARAMETER UNIT
(INPUT) (OUTPUT) TA = MIN to MAX CJ)
SNS4ALS164 SN74ALS164 ..J
MIN Typt MAX MIN Typt MAX <C
f max 60 60 MHz
tpHL CLR Any Q 12 12 ns
tpLH 10 10
CLK Any Q ns
tpHL 11 11
tAli typical values are at Vee = 5 V, TA = 25°C.

33
TEXAS 2-149
INSTRUMENTS
16
»
r-
en
»
z
c
»
en
o
:lJ
o
c
=t
en
2-150
PARALLEL·LOAD 8·BIT SHIFT REGISTERS
02661, JUNE 1982
• Complementary Outputs SN54AlS165 .•• J PACKAGE

SN74AlS165 ••• N PACKAGE
• Direct Overriding Load (Data) Inputs
ITOPVIEWI
• Gated Clock Inputs
SH/Lo VCC
• Parallel-to-Serial Data Conversion ClK ClK INH
• Package Options Include Both Plastic and E 0
Ceramic Chip Carriers in Addition to Plastic and F C
Ceramic DIPs G B
H A
• Dependable Texas Instruments Quality and OH SER
Reliability GND QH
description
The 'AlS165 is an a-bit serial shift register that, SN54AlS165 ••• FH PACKAGE
when clocked, shifts the data toward serial output SN74AlS165 ..• FN PACKAGE
QH. Parallel-in access to each stage is provided by ITOPVIEWI
eight individual direct data inputs that are enabled by ::I:
0 Z
a low level at the SH/lD input. The 'ALS165 also
~:2
1
-I:I:U
u;;
U-I
features a clock inhibit function and a complemented
UCJ)Z>U
serial output OH.
3 2 1
Clocking is accomplished by a low-to-high transition E o
of the ClK input while SH/lD is held high and ClK F C
INH is held low. The functions of the ClK and ClK NC NC
INH (clock inhibit) inputs are interchangeable. Since a G B
low ClK input and a low-to-high transition of ClK H 14 A
INH will also accomplish clocking, ClK INH should be 9 1011 1213
changed to the high level only while the ClK input is :I: 0 U :I:a:
high. Parallel loading is inhibited when SH/ill is held 10 ~ Z 0 ~ en
high. The parallel inputs to the register are enabled
NC - no Internal connection
!::
while SH/lD is low independently of the levels of ::::J
ClK,ClK INH, orSER~pu~. (J
The SN54AlS165 is characterized for operation
logic symbol a:
(J
over the full military temperature range of - 55°C to
125°C. The SN74AlS165 is characterized for en
operation from ooC to 70 0 C.
SH/LD (1)
«
o
ClKINH
z
FUNCTION TABLE elK
«
INPUTS
ClK FUNCTION
SER
A
en
...J
SH/LD ClK
L X
INH
X PARALLEL lOAD
B «
C
H H X NO CHANGE
D
H X H NO CHANGE
E
H L t SHIFT
F
H t L SHIFT
SHIFT - content of each internal register G
shifts toward serial output 0H' qata at serial (61
input is shifted into first register.
H

product under development. Texas TEXAS 2-151
discontinue this product without notice. POST OFFICE BOX 225012 • DALLAS, TEXAS 75265

PARAllEL
INPUTS
typical shift, load, and inhibit sequences

ClK
ClKINH
SER ____ ~ ______ ~-- _________________________________
- »
r-
en
»
2
DATA
SH1m-W
AJ.":l
c~~
E---1f:l~
I
:
I
I
I
l
l
~----~----------------------------------
____~__________________________________
____ ___________________________________
~
F I l
C I
I
»
en
G~~____~____________~____________________
H~L--__~____________________________
Q
::u
o I
c I
I
l
=i I- INHIBIT -1-------- SERIAL S H I F T - - - - - - - -

en LOAD
Supply voltage, Vee ................' ............................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free·air temperature range: SN54ALS165 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to 125°C
SN74ALS165 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . oOe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to 150°C
2-152
TEXAS
INSTRUMENTS
PARALLEL·LOAD 8·81T SHIFT REGISTERS
D2661. APRIL 1982-DECEM8ER 1983
• Synchronous Load SN54ALS166 . . . J PACKAGE

• Direct Overriding Clear (TOPVIEWI
• Parallel to Serial Conversion
• Package Options Include Both Plastic and Ceramic VCC
SER
Chip Carriers in Addition to Plastic And Ceramic DIPs
A SH/[5
• Dependable Texas Instruments Quality and Reliability B H
C QH
description D G
ClK F
The' AlS 166 8-bit shift register is compatible with most other INH
ClK E
TTL logic families. All inputs are buffered to lower the drive
GND ClR
requirements. Input clamping diodes minimize switching
transients and simplify system design.
These parallel-in or serial-in, serial-out registers have a SN54ALS166 . . . FH PACKAGE

complexity of 77 equivalent gates on a monolithic chip. They SN74ALS166 . . • FN PACKAGE
feature gated clock inputs and an overriding clear input. The (TOPVIEWI
parallel-in or serial-in modes are established by the shiftlload in-
put. When high, this input enables the serial data input and ul~
couples the .eight flip-flops for serial shifting with each clock ffi
U U J:
«UlZ>Ul
pulse. When low, the parallel (broadside) data inputs are enabled
and synchronous loading occurs on the next-clock pulse. During
parallel loading, serial data flow is inhibited. Clocking is ac- B H
complished on the low-to-high-Ievel edge of the clock pulse C QH
through a two-input positive NOR gate permitting one input to be NC NC
used as a clock-enable or clock-inhibit function. Holding either of D G
ClKINH F
the clock inputs high inhibits clocking; holding either low enables
the other clock input. This, of course, allows the system clock to
en
be free-running and the register can be stopped on command t:::
with the clock input. The clock-inhibit input should be changed to ::l
the high level only when the clock input is high. A buffered, direct CJ
clear input overrides all other inputs, including the clock, and sets NC-No Internal connection
a:
all flip-flops to zero. CJ
The SN54AlS 166 is characterized for operation over the full logic symbol en
military temperature range of - 55 °C to 125°C. The <t
SN7 4AlS 166 is characterized for operation from 0 °C to 70 °C.
SRGB c
ClR Z
SH/LD <t
FUNCTION TABLE CLKINH
en
...I
INPUTS INTERNAL
OUTPUT
eLK <t
SHIFTI CLOCK PARALLEL OUTPUTS SER
CLEAR CLOCK SERIAL °H
LOAD INHIBIT A ... H °A °B A
L X X X X X L L L B
H X L L X X °AO OBO OHO C
H L L t X a ... h a b h D
H H L t H X H °An OGn
H H L t L X L OAn °Gn
H X H t X X °AO OBO OHO
(13)
OH

:3
This document contains information on a product under
development. Texallnstruments ,.servas the right to
TEXAS 2-153
INSTRUMENTS
typical clear, shift, load, inhibit, and shift sequences
CLOCK
CLOCKINHIBIT-'~~________________________~____~r-----l~ ____________________________
I
-
I I
CLEAR -UI
I I
SERIAL INPUT ~__~__________________~____~______~~_________________________
I I
SHIFT/LOAD I Ur---~~-----------
I
l> A __~~________________________~__~~~____~~_________________________
r- I
(J) LI
I
C __~~________________________~__~~~____~~_________________________
l>
:2 D ____~______________________________~L~~~______~_________________________
C PARALLEL
INPUTS
I
l>
(J)
--~~------------------------~--~~~----~~------------------------- I
L,
o G ____ ~________________________~__~~~----~~-------------------------
:u H __~~________________________~__~~~____~~~_______________________
o
c: OUTPUT QH ::J._.:.....______________________---'
=i
(J)
1 - - - - SE RIAL SHI FT ------------t
CLEAR
Input voltage . . . . . . . . . . . . . . . . ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS166 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS166 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70o~
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " - 65 °e to 1 50 °e
2-154 TEXAS
INSTRUMENTS
PARALLEL-LOAD 8-BIT SHIFT REGISTERS

UNIT
CLR low
tw Pulse duration CLK high ns
ClK low
SH/lD
Setup time
tsu Data ns
before ClKI
ClR inactive
th Hold time. data after ClKt ns
SN54AlS166 SN74ALS166
VIK VCC = 4.5 V. II = -18 rnA -1.5 -1.5 V
VOH VCC = 4.5 V to 5.5 V. 10H = -0.4 rnA Vee- 2 Vee- 2 V
VCC = 4.5 V. 10l = 4 rnA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V. 10l = 8 rnA 0.35 0.5
II VCC = 5.5 V. VI = 7 V 0.1 0.1 rnA CJ)
IIH VCC = 5.5 V. VI = 2.7 V 20 20 /LA !::
III VCC = 5.5 V. VI = 0.4 V -0.1 -0.1 rnA ::::>
10i VCC = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA u
ICC VCC = 5.5 V See Note 1 16 16 rnA a::
t All typical values are at Vee ~ 5 V. TA ~ 25°e. u
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' CJ)
NOTE 1: With 4.5 Volts applied to the serial input and all other inputs except the clock grounded, lee is measured after a clock transition from 0 to 4.5 volts.
<t
c
switching characteristics (see Note 1) 2:
Vcc = 4.5 V to 5.5 V.
<t
CL = 50 pF. CJ)
...J
FROM TO R1 = 500 fl.
PARAMETER
UNIT <t
f max 60 60 MHz
tpHl ClR QH 10 10 ns
tplH 12 12
ClK QH ns
tpHl 13 13
tAli typical values are at Vee ~ 5 V, TA ~ 25°e.

TEXAS 2-155
INSTRUMENTS
~
l>
r-
tf)
l>
2
C
l>
tf)
o
::c
o
c
:::;
tf)
2-156
SN74ALS168A, SN74ALS169A, SN74AS168, AS74AS169
SYNCHRONOUS 4·BIT UP/DOWN DECADE AND BINARY COUNTERS
D2661, DECEMBER 1982- REVISED DECEMBER 1983
• Fully Synchronous Operation for Counting SN54ALS', SN54AS' • , . J PACKAGE

and Programming SN74ALS', SN74AS' . • . N PACKAGE
(TOP VIEW)
• Internal Look-Ahead for Fast Counting
• Carry Output for n-Bit Cascading
u/5 VCC
ClK RCO
• Fully Independent Clock Circuit A QA
8 Q8
C Qc
D QD
and Ceramic DIPs
ENP ENT
• Dependable Texas Instruments Quality and GND LOAD
Reliability
description SN54ALS', SN54AS' FH PACKAGE

SN74ALS', SN74AS' FN PACKAGE
These synchronous presettable counters feature an
(TOP VIEW)
internal carry look-ahead for cascading in high-speed
counting applications. The' AlS 168A and 'AS 168 are
decade counters and the' AlS 169A and 'AS 169 are
4-bit binary counters. Synchronous operation is
provided by having all flip-flops clocked
A QA
simultaneously so that the outputs change coincident 8 Q8
with each other when so instructed by the count- NC NC
enable inputs and internal gating. This mode of C QC
operation helps eliminate the output counting spikes D QD
that are normally associated with asynchronous (ripple
9 1011 1213
clock) counters. A buffered clock input triggers the
four flip-flops on the rising (positive-going) edge of the , 0..
ZZz«Z
w(!) OW
° Uloll- en
clock waveform. ...J
!::
These counters are fully programmable; that is, the NC - no internal connection.
::>
outputs may each be preset to either level. The load (.)
input circuitry allows loading with the carry-enable ex:
output of cascaded counters. As loading is (.)
synchronous, setting up a low level at the load input
disables the counter and causes the outputs to agree en
with the data inputs after the next clock pulse. <C
The carry look-ahead circuitry provides for cascading counters for n-bit synchronous application without additional C
gating. Instrumental in accomplishing this function are two count-enable inputs and a carry output. 80th count enable 2:
inputs (ENP and ENT) must be low to count. The direction of the count is determined by the level of the UfD input.
<C
When UfD is high, the counter counts up; when low, it counts down. Input ENT is fed forward to enable the carry en
output. The ripple carry output (RCO) thus enabled will produce a low-level pulse while the count is zero (all inputs low) ..J
counting down or maximum (9 or 15) counting up. This low-level overflow carry pulse can be used to enable <C
successive cascaded stages. Transitions at ENP or ENT are allowed regardless of the level of the clock input. All inputs
are diode-clamped to minimize transmission-line effects, thereby simplifying system design.
These counters feature a fully independent clock circuit. Changes at control inputs (ENP, ENT, lOAD, UiO) that will
modify the operating mode have no effect on the contents of the counter until clocking occurs. The function of the
counter (whether enabled, disabled, loading, or counting) will be dictated solely by the conditions meeting the stable
setup and hold times.
The SN54AlS168A, SN54AS168, SN54AlS169A, and SN54AS169 are characterized for operation over the full military
temperature range of -55°C to 125°C. The SN74ALS168A, SN74AS168, SN74AlS169A, and SN74AS169 are
characterized for operation from O°C to 70 °C.

\3
TEXAS 2-157
INSTRUMENlS
SYNCHRONOUS 4·81T UP/DOWN DECADE COUNTERS
•ALS 168A•• AS 168 logic diagram (positive logic) •ALS 168A •• AS 168 logic symbol
»
r-
en
»
:2
C
»en
(")
:lJ
(")
c
=t
en
12
2-158 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012·. DALLAS. TEXAS 75265
SYNCHRONOUS 4·BIT UP/DOWN BINARY COUNTERS
'ALS 169A, AS 169 logic diagram (positive ,logic) 'ALS169A, 'AS169 logic symbol
CLK~:-H::t:j=+=t=I=~ __-r"""
en
!::
::::>
ua:
-u
en
<t
C
Z
<t
en
..oJ
<t
Pin' numbers shown are for J and N packages.
. TEXAS 2-159
INSTRUMENTS
.ALS 168A .. AS 168 typical load. count. and inhibit sequences
1. Load (preset) to BCD seven

2. Count up to eight, nine (maximum), zero, one, and two
3. Inhibit
4. Count down to one, zero (minimum), nine, eight, and seven
I
A-.J L
B-.J I
1-
DATA
INPUTS
C-.J I
L
D r
I
- l>
r-
til
l>
ClK
ENPandENT--'~~__~~__________________~
I
I
2 I
C I:
l>
til
0 ----:--!l
6 _ __ ..J I~'- - - - - - - - - - - - - - - '
r----
.
I
(")
lJ
°c
___ ..J
I
----:--rl~I----------------------------------~----------------~
I
r----
(") -- -.., I I
c °D ____ LiJ I
L..-
=i II
til ~ ----I
___ -l
: 7 I I
I I
I I LJ o 2
I
2 2
u
o 9 8 7
I II... ·---COUNT UP -----··I-INHIBIT-I ~ COUNT DOWN - - - - +

~
LOAD
2-160 TEXAS
INSTRUMENTS
, ALS 169A, 'AS 169 typical load, count, and inhibit sequences
1. load (preset) to binary thirteen

2. Count up to fourteen, fifteen (maximum), zero, one, and two
3. Inhibit
4. Count down to one, zero (minimum), fifteen, fourteen, and thirteen
A 1'---';"'" - -
--I L..._
B____.-.1'r
__-
DATA
INPUTS
ClK
.--
L..._
__ Ji
U/O-
II en
I I t:::
I I
--,~~____I_I____________________~ :::>
BWandTIIT
u
I I
I I a:
I
I
u
I: en
0B ==lJJr-----..., II ~-----.-.I
L ~
c
I
z
~
Go - --I en
...J
--....I
~
nco - --I
--~
: 13 14
LJ·
15 0 21
I
I
2 2
u
o 15 14 13
LI. . ·---COUNT UP - - -••I-INHIBIT-I ~COUNTDOWN-----

LOAD
TEXAS 2-161
INSTRUMENTS
TYPES SN54ALS168A, SN54ALS169A, SN74ALS168A, SN74ALS169A
Supply voltage. Vee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage .......................................... ;. . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS 168A. SN54ALS 169A .............. " - 55°C to 125°C
SN74ALS168A. SN74ALS169A .................... ooe to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50°C

fclock Clock' frequency 0 25 0 30 MHz
tw Pulse duration CLK high or low 20 16.5 ns
A. B. e. or D 20 15
ENP or ENT 25 20
tsu Setup time before CLKt ns
LOAD 20 15
UfD 20 15
-
th Hold time. data after eLKt 0 0 ns
TA Operating free-air temperature - 55 125 0 70 °e
»
r-
en PARAMETER TEST CONDITIONS SN54ALS169A SN74ALS169A UNIT
»
2 VIK Vec = 4.5 V. II = - 18 mA
MIN Typt MAX
-1.5
MIN TYpt MAX
- 1.5 V
C VOH VCC = 4.5 V to 5.5 V. 10H = -0.4 rnA vee- 2 Vce- 2 V
»
en
VOL
Vec
Vce
=
=
4.5 V.
4.5 V.
10L
10L
= 4 mA
= 8 mA
0.25 0.4 0.25
0.35
0.4
0.5
V
II Vce = 5.5 V. VI =7V 0.1 0.1 mA

n IIH Vec = 5.5 V. VI = 2.7 V 20 20 /lA
:lJ IlL Vce = 5.5 V. VI = 0.4 V -0.2 -0.2 mA
n I RCO =
-15 -70 -15 -70
c 10*
10 Vee 5.5 V. Vo = 2.25 V
-30 - 1 12 -30 - 1 12
mA
=i Ice Vee = 5.5 V 15 25 15 25 rnA

en tAli typical values are at Vee = 5 V. TA = 25°C.
121
2-1'62 TEXAS
INSTRUMENTS
TYPES SN54ALS168A. SN54ALS169A. SN74ALS168A. SN74ALS169A
. SYNCHRONOUS 4·BIT UP/DOWN DECADE AND BINARY COUNTERS
, ALS 168A, 'ALS 169A switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 500 Q.
FROM TO
(IN pun (OUTPUn
MIN MAX MIN MAX
f max 25 30 MHz
tplH 10 32 10 28
ClK RCO ns
tpHl 6 22 6 18
tplH 5 19 5 16
ClK Any Q ns
tpHl 5 20 5 16
tplH 5 19 5 16
ENT RCO ns
tpHl 3 16 3 13
tplH 5 25 5 23
UfO RCO ns
tpHl 5 23 5 19
NOTE1: For load circuit and voltage waveforms. see page 1·12.
en
~
:::>
u
a:
u
en
<t
C
z
<t
en
..J
<t
TEXAS 2-163
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS168, SN54AS169 . . . . . . . . . . . . . . . . . . " - 55 °e to 125 °e
SN74AS168,SN74AS169 . . . . . . . . . . . . . . . . . . . . . . . . 0 0 eto70oe

SN54AS168 SN74AS168
fclock Clock frequency MHz -
tw Pulse duration ClK high or low ns
A, B, C, or D
ENP or ENT
tsu Setup time before ClKt ns
LOAD
UfD
th Hold time, data after CLKt ns
TA Operating free-air temperature -55 125 0 70 DC
SN54AS168 SN74AS168
VIK VCC = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH Vec = 4.5 V to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vce - 4.5 V, 10L - 20 rnA 0.25 0.5 0.25 0.5 V
II Vec = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vec = 5.5 V, VI = 2.7 V 20 20 p.A
I Load, ENT, UfD -1 -1
IlL I All others Vce = 5.5 V, VI = 0.4 V rnA
-0.5 -0.5
lOt Vce = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
ICC Vec = 5.5 V 46 46 rnA
t All typical values are at Vee = 5 V, T A = 25°e.

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS-
PRODUCT PREVIEW 12£

2-164 development. Texaslnstrumentsroservos tho right to
chango or discontinue this product without notice.
TEXAS
INSTRUMENTS
'AS 168, 'AS 169 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 500 n.
FROM TO
(INPUT! (OUTPUT)
SN54AS168 SN74AS168
SN54AS169 SN74AS169
f max MHz
tpLH RCO (with LOAD high! 9.5 9.5
tPLH CLK RCO (with LOAD low! 5.5 5.5 ns
tpHL RCO 7.5 7.5
\ 5 5
tPLH
CLK Any Q ns
tpHL 6 6
tpLH 3 3
ENT RCO ns
tpHL 4 4
tpLH 7.5 7.5
ufo RCO ns
tPHL 10.5 10.5
t All typical values are at Vee = 5 V. T A = 25 CC.

NOTE1: For load circuit and voltage waveforms, see page 1-12.
13 PRODUCT PREVIEW
development. Texaslnatruments re .. rves the right to
. TEXAS 2-165
INSTRUMENlS
- l>
r-
C/)
l>
:2
C
l>
C/)
Q
:a
(')
c
=i
C/)
2-166
HEXIQUAORUPLE O·TYPE FLlp·FLOPS WITH CLEAR
02661, APRIL 1982-REVISION DECEM8ER 1983
SN54ALS174,SN54AS174. J PACKAGE
• ' ALS 1 74 and 'AS 174 Contain Six Flip-Flops with SN74ALS174, SN74AS174 . . . N PACKAGE
Single-Rail Outputs ITOPVIEW)
• 'ALS175 and 'AS175 Contain Four Flip-Flops with CLR VCC
Double-Rail Outputs 10 60
10 60
• Buffered Clock and Direct Clear Irtputs
20 50
• Applications Include: 20 50
Buffer/Storage Registers 3D 40
Shift Registers 30 40
Pattern Generators GNO CLK
• Fully Buffered Outputs for Maximum Isolation from SN54ALS174, SN54AS174 . FH PACKAGE
External Disturbance ('AS only) SN74ALS174,SN74AS174. . FNPACKAGE
(TOP VIEW)
Chip Carriers in Addition to Plastic and Ceramic DIPs 015 U
...-UZ> CO
~o
60
description 50
These monolithic, positive-edge-triggered flip-flops utilize TTL NC
circuitry to implement Ootype flip-flop logic. All have a direct 5Q
clear input and the' ALS 1 75 and' AS 1 75 feature complementary 40
outputs from each flip-flop.
Information at the 0 inputs meeting the setup time requirements

is transferred to the outputs on the positive-going edge of the
clock pulse. Clock triggering occurs at a particular voltage level
and is not di~ectly related to the transition time of the positive- SN54ALS175,SN54AS175 . J PACKAGE
going pulse, When the clock input is at either the high or low SN74ALS175,SN74AS175 . . . N PACKAGE
en
level, the 0 input signal has no effect at the output. (TOP VIEW) !::
CLR VCC
::J
These circuits are fully compatible for use with most TTL circuits.
40
U
The SN54ALS174, SN54ALS175, SN54AS174, and
10
10 4Q
ex:
SN54AS 17 5 are characterized for operation over the full military 10 40 U
temperature range of -55°C to 125°C. The SN74ALS174, 20 3D en
SN74ALS175, SN74AS174, and SN74AS175 are character- 20 30 <t
ized for operation from ooC to 70°C. 20 30
GNO CLK
C
z
SN54ALS175. SN54AS175
SN74ALS175. SN74AS175
FH PACKAGE
. FN PACKAGE
<t
(TOP VIEW)
en
..J
015 U
...-uZ>'<t
~o <t
FUNCTION TABLE
(EACH FLIP-FLOP)
40
INPUTS OUTPUTS
40
CLR CLK 0 a at NC
L x X L H
3D
H t H H L
30
H t L L H
H L X ao 00
OOU~d
t 'ALS175 and 'AS175 only Nt5 Z cjM
NC - No internal connection,

13
TEXAS 2-167
INSTRUMENTS
POST OFFICE BOX 225012 • OALLAS. TEXAS 75265'
TYPES SN54ALS174, SN54ALS175,·SN54AS17~ SN54AS175
HEX/QUADRUPLE D·TYPE FLlp·FLOPS WITH CLEAR
logic symbols
'AlS174, 'AS174 'AlS175, 'AS175
10 (3)
20 (4)
30 (6) 30
40 (11) 40
50 (13) (12) 50
(14) (15) 60
60
ClR 111
ClK
1D ~~---+-+-....j 10
10
2D -...;.14.;.;1_ _ _+-11--1 2D 151 20'
20
3D --:,16;;.:,1_ _ _ I--I 3D 1121

H
4D 1111 4D 1131 40
40
5D 1131
6D 1141
Pin numbers shown a~e for J and N packages.
48
2-168 TEXAS
INSTRUMENTS
HEX/QUADRUPLE D·TYPE FLlP·FLOPS WITH CLEAR
Supply voltage, Vee .................................................................. 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS174, SN54ALS175 ... " ............... -55°e to 125°e
SN74ALS174, SN74ALS175 ....................... ooe to 70 0 e
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e

SN54ALS175 SN74AlS175 UNIT
IOH High-level output current -0.4 -0.4- rnA
CLR low 15 10
tw Pulse duration CLK high 12.5 10 /
ns
CLK low 12.5 10
tsu ns
before CLKt eLR inactive 8 6
th Hold time, data after elK t 0 0 ns
en
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) !::
::::>
SN54ALS174 SN74ALS174 CJ
PARAMETER TEST CONDITIONS SN54ALS175 SN74AlS175 UNIT a:
MIN Typt MAX MIN TVPt MAX
CJ
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
= IOH = -0.4 rnA V en
VOH Vee
Vec =
4.5 V to 5.5 V
4.5 V, IOL = 4 rnA
vee- 2
0.25 0.4
Vee- 2
0.25 0.4
V
«
VOL
Vee = 4.5 V IOL = 8 rnA 0.35 0.5 c
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA z
IIH
IlL
Vec
Vce
=
=
5.5 V,
5.5 V,
VI = 2.7 V
VI = 0.4 V
20
-0.1
20
-0.1
/LA
rnA
«
IOi Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
en
...J
Ice
L'ALS174
l'ALS175
Vee = 5.5 V, See Note 1
11
8
19
14
11
9
19
14
rnA «
tAli typical values are at Vee = 5 V, TA = 25°C. .
NOTE 1: ICC is measured with D inputs and elR grounded, and elK at 4.5 V.
33
TEXAS 2-169
INSTRUMENTS

Vcc = 4.5 V to 5.5 V
Cl = 50 pF,
Rl = 500 (}
FROM TO
(INPUT) (OUTPUT)
MIN MAX MIN MAX
f max 40 50 MHz
tpLH Any Q ('AlS175) 5 20 5 18
CLR ns
tpHL Any Q 8 26 8 23
tPLH Any Q 3 17 3 15
ClK ns
tpHl (or Q, 'AlS175) 5 20 5 17
Dflip·flop signal conventions

It is TI practice to name the outputs and other inputs of a D-type flip-flop and to draw its logic symbol based on the
assumption of true data (D) inputs. Then outputs that produce data in phase witl:! the data inputs are called Q and those
producing complementary data are called O. An inpl!t that causes a Q output to go high or a 0: output to go low is called
Preset; an input that causes a IT output to go high or a Q output to go low is called Clear. Bars are used over these pin
names (PRE and CLR) if they are active low.
In some applications it may be advantageous to redesignate the data input D. In that case. all the other inputs and
outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
pin numbers are shown in parentheses.
PAt" s (5) Q ClR (5) Q

ClK ~-C> C1 ClK
o 10
(6) Q o (6) Q
CLR R PRE
Notice that Q and 0 exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (1::>.) on PRE and CLR remain since these inputs are still active-low, but that the presence or absence of the
polarity indicator changes at 0, Q, and O. Of course pin 5 (0) is still in phase with the data input D, but now both are
considered active-low.
128
2-170 TEXAS
INSTRUMENTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " 7 V
Input voltage ..................................................................... " 7 V
Operating free-air temperature range: SN54AS174, SN54AS175 .. , .. " '" ., ., .... '" -55°C to 125°e
SN74AS174, SN74AS175 ....................... ~. DOG to 70 0 e
Storage temperature range .............. : ................................. " - 65°C to 150 0 e

SN54AS174 SN74AS174
CLR low 5.5 5
tw Pulse duration CLK high 4 4 ns
CLK low 6 6
Setup ti,me Data 4 4
tsu ns
before CLKt CLR inactive 6 6
th Hold time, data after CLKt 1 1 ns
en
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) !::
:)
SN54AS174 SN74AS174
PARAMETER
(.)
TEST CONDITIONS SN54AS175 SN74AS175 UNIT
a:
VIK VCC = 4.5 V, II = -18 mA -1.2 -1.2 V u
VOH VCC = 4.5 V to 5.5 V IOH = -2 mA VCC-2 VCC-2 V en
VOL VCC =
=
4.5 V, IOL = 20 mA
VI = 7 V
0.25 0.5 0.25 0.5 V «
II VCC
=
5.5 V,
VI = 2.7 V
0.1 0.1 mA
c
IIH VCC 5.5 V, 20 20 p.A
z
IlL
10:1:
VCC
VCC
=
=
5.5 V,
5.5 V,
VI = 0.4 V
Va = 2.25 V -30
-0.5
-112 -30
-0.5
-112
mA
mA «
l'AS174
VCC = 5.5 V, See Note 1
30 45 30 45
mA
en
ICC
I 'AS175 ..J
tAli typical values are at VCC = 5 V, TA = 25°C.

33 33
«
NOTE 1: ICC is measured with D, ClK, and PRE grounded, then with D, ClK, and ClR grounded.
Specifications are subject to change without notice. TEXAS 2-171
INSTRUMENTS
HEX/QUADRUPLE D·TYPE FLlP·FLOPS WITH CLEAR
'AS 174 switching characteristics (see Note 2)

Vcc = 4.5 V to 5.5 V
Cl = 50 pF.
Rl = 5000
FROM TO
(INPUT) (OUTPUT)
SN54AS174 SN74AS174
MIN MAX MIN MAX
f max 100 100 MHz
tpHl ClR Any Q 5 15 5 14 ns
tPlH 3.5 9.5 3.5 8
ClK Any Q ns
tpHl 4.5 11.5 4.5 10
'AS175 switching characteristics (see Note 2)

Vcc =4.5 V to 5.5 V.
Cl = 50 pF.
FROM TO Rl = 500 n.
PARAMETER UNIT
SN54AS175 SN74AS175
f max 160 160 MHz
tplH 5 5
ClR Any Q or Q ns
tpHl 5.5 5.5
tPlH 4 4
ClK Any Q or IT ns
tpHl 4 4
»
r-
en
»
2
C
»
en
Q
:JJ
n
C
~
CJ)
ADVANCE INFORMATION 121'
2 -1 72
This page contain. Information on a new product.
Specifications are subject to chenge without notice. TEXAS
INSTRUMENTS
TYPES SN54AS181A, SN54AS881A, SN74AS181A, SN74AS881A
ARITHMETIC LOGIC UNITSIFUNCTION GENERATORS
02661, DECEMBER 1982-REVISED DECEMBER 1983
• Package Options Include the AS 181 A in I SN54AS181A .... J OR JT PACKAGE

Compact 300-mil or Standard GOO-mil DIPs. SN54AS881A .•.. JT PACKAGE
The' AS881 A Is Offered in 300-mil DIPs. SN74AS181A .... N OR NT PACKAGE
SN74AS881A ...• NT PACKAGE
Both Devices Are Available in Both Plastic (TOPVIEWI
and Ceramic Chip Carriers
• Full Look-Ahead for High-Speed Operations 80 VCC
on Long Words AO A1
S3 81
• Arithmetic Operating Modes:
S2 A2
Addition
Subtraction S1 82
Shift Operand A One Position SO A3
Magnitude Comparison Cn B3
Plus Twelve Other Arithmetic M G
Operations FO C n +4
'F1 p
• Logic Function Modes
Exclusive-OR F2 A=8
Comparator GND F3
AND,NAND,OR,NOR
AS881 A Provides Status
I
Register Checks
Plus Ten Other Logic Operations SN54AS181A, SN54AS881A .... FH PACKAGE
SN74AS181A, SN74AS881A •... FN PACKAGE
and Reliability 'AS 181 A, 'AS881 A
(TOP VIEW I
logic symbol
en
ALU !::
SO 161
::>
}~
52 A2
Sl 151
S2 141
10.
51 82 u
a:
31
S3 131 SO A3
M 181 4 NC NC U
171
Cn Cn 83 en
M G <C
FO 11 en + 4 C
12131415161718 2
IU: I~ ~ ~ I ~ ~ 10-
<t
(!) < U)
..J
NC - no internal connection
<t
Pin numbers shown are J, JT. N and NT packages.
TYPICAL ADDITION TIMES (CL = 15 pF RL = 280 Q T A = 25 DCI

NUMBER ADDITION TIMES PACKAGE COUNT CARRY METHOD
OF USING 'AS881A USING'AS181A USING'S181 ARITHMETIC LOOK-AHEAD BETWEEN
BITS AND'AS882 AND'AS882 AND '5182 LOGIC UNITS CARRY GENERATORS ALU's
1 to 4 5 ns 5 ns 11 ns 1 NONE
5 to 8 10 ns 10 ns 18 ns 2 RIPPLE
9 to 16 14 ns 14 ns 19 ns 30r4 1 FULL LOOK-AHEAD
17 to 64 19 ns 19 ns 28 ns 5 to 16 2 to 5 FULL LOOK-AHEAD

This document contains information on
a new product. Specifications are subject TEXAS 2-173
to change without notice. INSTRUMENTS
ARITHMETIC LOGIC UNITS/FUNCTION GENERATORS
description
The' AS 181 A and' AS881 A are arithmetic logic units (ALU)ffunction generators that have a complexity of 75 and 77
equivalent gates respectively, on a monolithic chip. These circuits perform 16 binary arithmetic operations on two
4-bit words as shown in Tables 1 and 2. These operations are selected by the four function-select lines (SO, S1, S2,
S3) and include addition, subtraction, decrement, and straight transfer. When performing arithmetic manipulations,
the internal carries must be enabled by applying a low-level voltage to the mode control input (M). A full carry look-
.ahead scheme is made available in these devices for fast, simultaneous carry generation by means of two cascade-
outputs (pins 15 and 17) for the four bits in the package. When used in conjunction with the SN54AS882 or
SN74AS882 full carry look-ahead circuits, high-speed arithmetic operations can be performed. The typical addition
times shown previously illustrate the little additional time required for addition of longer words when full carry look-
ahead is employed. The method of cascading' AS882 circuits with these ALU's to provide multi-level full carry look-
ahead is illustrated under signal designations.
If high speed is not of importance, a ripple-carry input (C n ) and a ripple-carry output (C n + 4) are available. However,_
the ripple-carry delay has also been minimized so that arithmetic manipulations for small word lengths can be perform-
ed without external circuitry.
The 'AS 181 A and' AS881 A will accommodate ar:tive-high or active-low data if the pin designations are interpreted as
follows:
..
PIN NUMBER
Active-low data (Table 1)
Active-high data (Table 2)
Subtraction is accomplished by 1's complement addition where the 1's complement of the subtrahend is generated in-
ternally. The resultant output is A - B-1, which requires an end-around or forced carry to provide A-B.
l>
r- The 'AS 181 A and' AS881 A can also be utilized as a comparator. The A = B output is internally decoded from the func-
r.n tion outputs (Fa, F1, F2, F3) so that when two words of equal magnitude are applied at the A and B inputs, it will
l> assume a high level to indicate equality (A = B). The ALU must be in the subtract mode with C n = H when performing
z this comparison. The A = B output is open-collector so that it can be wire-AND connected to give a comparison for
C more than four bits. The carry output (C n + 4) can also be used to supply relative magnitude information. Again, the
ALU must be placed in the subtract mode by placing the function select inputs S3, S2, S 1, SO at L, H, H, L, respective-
l>
r.n ly.
Q
:a INPUT Cn OUTPUT Cn +4
ACTlVE·LOW DATA
(FIGURE 1)
ACTIVE·HIGH DATA
(FIGURE 2)
(")
c H H A~B A~B
=i H
L
L
H
A<B
A>B
A>B
A<B
til
L L A~B A~B
These circuits have been designed to not only incorporate all of the designer's requirements for arithmetic operations,
but also to provide 16 possible functions of two Boolean variables without the use of external circuitry. These logic
functions are selected by use of the four function-select inputs (SO, S1, S2, S3) with the mode-control input (M) at a
high level to disable the internal carry. The 16 logic functions are detailed in Tables 1 and 2 and include exclusive-OR,
NAND, AND, NOR, and OR functions.
2-174 TEXAS
INSTRUMENTS
description (continued)
The' A5881 A has the same pinout and same functionality as the' A5 181 A except for the p, G, and Cn + 4 outputs
when the dev,ice is in the logic mode (M = HI.
In the logic mode the' A5881 provides the user with a status check on the input words, A and B, and the output word
F. While in the logic mode the P, G and Cn +4 outputs supply status information based upon the following logical com-
binations:
P=FO+F1 +F2+F3
G=H
Cn +4=PC n
FUNCTION TABLE FOR INPUT BITS EQUAL/NOT EQUAL FUNCTION TABLE FOR INPUT PAIRS HIGH/NOT HIGH
- - S1-S2-L
SQ-S3-H - - and M-H
- - - - S2-H
SQ-S1-S3-L - and M-H
-
OUTPUTS OUTPUTS
Cn DATA INPUTS Cn DATA INPUTS
G P Cn +4 G P Cn 4
H AO-BO A1-B1 A2-B2 A3-B3 H L H H AO or BO=L A1orB1=L A2 or B2 =L A3 or B3 =L H L H
L AO=BO A1 =B1 A2=B2 A3=B3 H L L L AO or 90=L A1 or 91 =L A2 or 92 =L A3 or 93 =L H L L
X AO-i'BO X X X H H L X AO=BO=H X X X H H L
X X A1-i'B1 X X H H L X X A1=91=H X X H H L
X X X AUB2 X H H L X X X A2=B2=H X H H L
X X X X A3-i'B3 H H L X X X X A3=B3=H H H L
The combination of signals on the 53 through 50 control lines determine the operation performed on the data words to
generate the output bits Fi. By monitoring the P and Cn + 4 outputs, the user can determine' if all pairs of input bits are
equal (see table above) or if any pair of inputs are both high (see table above). The' A5881 A has the unique feature of
providing an A = B status while the exclusive-OR (ED) function is being utilized. When the control inputs (53, 52, 51,
50) equal H, L, L, H; a status check is generated to determine whether all pairs (Ai, Bil are equal in the following man-
ner: P = (AO E£) BO) + (A 1 E±) B 1) + (A2 @ B2) + (A3 E±) B3). This unique bit-by-bit comparison of the data words which
en
is available on the totem pole P output is particularly useful when cascading' A5881 'so As the A = B condition is sens-
!::
ed in the first stage the signal is propagated through the same ports used for carry generation in the arithmetic mode (F»
:>
(,)
and G). Thus the A = B status is transmitted to the second stage more quickly without the need for external multiplex-
ing logic. The A = B open-collector output allows the user to check the validity of the bit-by-bit result by comparing
a:
the two signals for parity. C3
en
If the user wishes to check for any pair of data inputs (Ai, Bil being high, it is necessary to set the control lines <t
(53,52,51,50) to L, H, L, L.The data pairs will then be ANDed together and the results ORed in the following manner: C
is = A080+A1B1 +A2B2+A383. :2
<t
53 I 52 I 51 I 50 I M I p = FO+F1 +F2+F3 en
..J
L I H L L ILl H 1 AOBO+A1B1 +A2B2+A3B3
<t
H I L I L I H I H I (AO EJ) BO)+(A1 EB B1)+(A2 ffi B2)+(A3 E!) B3)
signal designations
In both Figures 1 and 2, the polarity indicators (-=-) indicate that the associated input or output is active-low with
respect to the function shown inside the symbol and the symbols are the same in both figures. The signal designations,
in Figure 1 agree with the indicated internal functions based on active-low data, and are for use with the logic functions
and arithmetic operations shown in Table 1. The signal designations have been changed in Figure 2 to accommodate
the logic functions and arithmetic operations for the active-high data given in Table 2. The' A5 181 and' A5881
together with the' A5882 and '5182 can be used with the signal designation of either Figure 1 or Figure 2.
~83
TEXAS 2-175
INSTRUMENTS
'AS181A 'AS181A
'AS881 A 'AS881A
ALU ALU
so 161 SO 161
Sl 151 1151 -
10 .. 151 CP
l'
S2 141 10 .. 151 CG 1171 cr
31
S3 131 1141 A-B
6IP'01~
M 181 4 10 .. 151 CO
1161 C n+4
Cn 171
'AS882 'AS882
CPG CPG
-
Cal
(6) Cn+8 161 1:'n+8
COl
1111 Cn +16 1111 Cn+16

C03 C03
1171 Cn +24 1171 t:n+24

CO C05
l> C07
1221 Cn+32
C07
1221 t:n+32
r-
tJ)
l>
2
C FIGURE 1 FIGURE 2
(USE WITH TABLE 1) (USE WITH TABLE 2)
l>
tJ) TABLE 1 TABLE 2
Q SELECTION 1-_ _-,-_ _ _A:::::C::..!T.:.:IV:.::E:::.L~O.:..:W.!:O:::Ac!.!TA::..__ _ _ _ ___I

M' L; ARITHMETIC OPERATIONS
SELECTION
M~H
ACTlVE·HIGH DATA
M - L; ARITHMETIC OPERATIONS
J:J LOGIC
o S3 52 51 SO LOGIC
FUNCTIONS
Cn = L
(no carryl
Cn • H
(with carryl S3 S2 SI SO FUNCTIONS Ina carryl (withcarryl
c L
L
L
L
L
L
L F=A
F=AR
F=AMINUSI
F=ABMINUSI
F=A
F=AB
L
L
L
L
L
H
F=A
F= ATii
F=A
F' A + B
F = A PLUS 1
F = (A + BI PLUS 1
=i
tJ)
L, L H F=A+B F=A8MINUSI F=AS L
L
L
L
H
H
L
H
F = AB
F=O
F=A+B
F = MINUS 1 (2', COMPLI
F = (A + 81 PLUS 1
F = ZERO
L L H F=1 F = MINUS 1 (2',COMPI F = ZERO
L H L F = ATii F = A PLUS (A + 81 F = A PLUS (A + BI PLUS 1 L H L L F = As F = A PLUS Ali F = A PLUS AS PLUS 1
L H L H F =B F = AB PLUS (A + BI F = AB PLUS IA + BI PLUS 1 L H L H F =1i F = (A + BI PLUS Ali F = (A + BI PLUS A8PLUS 1
L H H L F=A 0 B F = A MINUS B MINUS 1 F = A MINUS B H H L F =A 0 B F • A MINUS B MINUS 1 F=AMINUSB
L H H H F=A +8 F = A +S F = (A + BI PLUS 1 H H H F=A8 F = ABMINUS 1 F =AS
H L L F = AB F = A PLUS (A + BI F = A PLUS (A + BI PLUS 1 H L L L F=A+B F = A PLUS AB F = A PLUS AB PLUS 1
H L H F=A 0 B F = A PLUS B F = A PLUS B PLUS 1 H L L H F=A 0 B F =A PLUS B F = A PLUS B PLUS 1
H L H L F=B F = A8PLUS (A + BI H L H L F=B F = (A + lil PLUS AB F = (A + 61 PLUS AB PLUS 1

F = A8PLUS IA + BI PLUS 1
H L H H F=A+B F = IA+ BI F = (A + BI PLUS 1 H L H H F = AB F = AB MINUS 1 F = AB
H H L L F=Q F = APLUS A· F = A PLUS A PLUS 1 H L L F=1 F=APLUSA* F = A PLUS A PLUS 1
H H L H F = AB F = AB PLUS A F = AB PLUS A PLUS 1 H L H F=A+6 F = (A + BI PLUS A F = IA + BI PLUS A PLUS 1
H H H L F = AB F=ABPLUSA F = ABPLUS A PLUS 1 H H L F=A+B F = (A + BI PLUS A F = (A + BI PLUS A PLUS 1
H H H H F=A F = A F = A PLUS 1 H H H H F=A F = A MINUS 1 F=A
• Each bit is shifted to the next more significant position,
12
2-176 TEXAS
INSTRUMENTS
TYPES SN54AS181A, SN74AS181A

'AS181A
~~
S3 (31
52 141
51 lSI
1171
50~
1181
.-{)
-~~ 1161
3-< ~
~
,,-/
?-J
l ~~
11S1
1191
3
))
""
./
'~
,JL)
(131
~~
~~
1201
2-
~
2
1211
1
II " 1111
F2 ..
:~
./
~~
C/)
!::
1221 ::::>
1---'
~ u
1141 a:
I
~ A=B
c:;
1231 C/)
1
(101
«
~~
1) ""
,~./ rl C
2
«
~
~
III
-L C/)
-I
O~
~, «
I
/l) (9)
FO
(21
0
~W
(81
M
(71
C
33
TEXAS 2-177
INSTRUMENlS
SJ (3) 'AS881A
S2 (4)
S1 (5)
so (6)
(17) G
(16)
> - - - - - c " ....
Jt>-___~
(20)
82
(15)
P
A2 (21)
IIIIIfJ A-B
l>
r-
en
l>
2,
0
l>
en
Q
::a
0
c:
=t
en so
>+-----f"o
2-178 TEXAS
INSfRUMENlS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage (A = B output only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS181 A, SN54AS881 A . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74AS181A,SN74AS881A . . . . . . . . . . . . . . . . . . . . . . . ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50 DC

SN54AS' SN74AS'
UNIT
VOH High-level output voltage A = B output only 5.5 5.5 V
All outputs except
-2 -2 rnA
10H High-level output current A=B andG
G -3 -3 rnA
All outputs
Low-level output current 20 20 rnA
10L except G
G 48 4B rnA
en
!::
::>
u
a:
u
en
«
c
z
«
en
...J
«
:83
TEXAS 2-179
INSTRUMENTS
SN54AS' SN74AS'
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
Any output
Vee = 4.5 V to 5.5 V. IOH= -2 mA Vee- 2 Vee- 2 V
VOH except A = B
G Vee = 4.5 V. IOH = -3 mA 2.4 ' 3.4 2.4 3.4 V
10H A = B Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
Any output
Vee = 4.5 V. IOL = 20 mA 0.3 0.5 0.3 0.5 V
VOL except IT
G Vee = 4.5 V. 10L = 48 mA 0.4 0.5 0.4 0.5 V
M input 0.1 0.1
Any A or B input 0.3 0.3
II Vee = 5.5 V. VI = 7 V mA
Any S input 0.4 0.4
earry input 0.6 0.6
M input 20 20
Any A or B input 60 60
IIH Vee = 5.5 V. VI = 2.7 V p,A'
Any S input 80 80
earry input 120 120
M input -2 -2
Any A or B input -6 -6
IlL Vee = 5.5 V. VI = 0.4 V mA
Any S input -8 -8
earry input -12 -12
All outputs except
-30 -45 -112 -30 -45 -112
10:1: A = B and IT Vee = 5.5 V. Vo = 2.25 V mA
G -165 -165
l'AS181A 135 200 135 200
lee Vee = 5.5 V mA
I 'AS881A 135 210 135 210
t All typical values are at Vee = 5 V, TA = 25 ae.

*The output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current, lOS'
128:
2-180 TEXAS
INSTRUMENTS
VCC=5V,
CL= 15 pF, VCC=4.5 V to 5.5 V,
RL=500 Q CL = 50 pF (15 pF for A = B),
FROM TO TEST (280 Q for A=BI. RL=500 Q (280 Q for A=BI.
PARAMETER UNIT
(INPUT) (OUTPUT) CONDITIONS TA = 25°C TA=MIN to MAX
'AS181A SN54AS181A SN74AS181A
'ASB81A SN54AS881A SN74AS881A
MIN Typt MAX MIN Typt MAX MIN Typt MAX
tpd Cn Cn +4 5 2 7 11 2 7 9 ns
Any M-O V, S1 -S2-0 V,
tpd Cn +4 6 2 8 14 2 8 12 ns
A or B SO=S3=4.5 V (SUM mode)
Any M=O V, SO=S3=0 V,
tpd Cn +4 7 2 8 20 2 8 16 ns
A orB S1 =S2 =4.5 V (~mode)
tpd Cn Any F M = 0 V (SUM or DIFF mode) 5 3 6 11 3 6 9 ns
Any M-O V, S1-S2-0 V,
tpd G SO =S3 =4.5 V (SUM mode)
4 2 5 9 2 5 7 ns
AorB
Any M=O V, 50=53=0 V,
tpd G S1 =52 =4.5 V IDIFF mode)
5 2 6 12 2 6 9 ns
A or B
Any M=O V, 51 =52=0 V,
tpd p 5 2 6 11 2 6 8 ns
A or B 50=53=4.5 V (5UM mode)
Any M=O V, 50=53=0 V,
tpd p 5 2 6 13 2 6 10 ns
AorS 51 =52 =4.5 V IDIFF mode)
Ai or M=OV,51=S2=OV,
tpd Fi 5 2 5 11 2 5 8 ns
Bi 50=53=4.5 V (SUM mode)
Ai or M=O V, SO=51 =0 V,
tpd Fi 5 2 6 12 2 6 10 ns
Bi 51 =52=4.5 V (DiFFmode)
Ai or
tpd Fi M=4.5 V (LOGIC mode) 6 2 6 16 2 6 11 ns
Bi C/)
tpd
Any A -
A=B
M=OV,50=S3=OV,
12 4 14 26 4 14 21 ns !::
or B 51 ;'S2=4.5 V (DIFF mode) :J
U
addditional ' AS881 A switching characteristics involving status checks (see Note 1) a:
VCC=5V, VCC=4.5 V to 5.5 V,
U
CL=15pF, CL=50 pF, - C/)
PARAMETER
FROM TO TEST RL=500 Q, RL~500 Q,
UNIT
«
(INPUT) (OUTPUT) CONDITIONS TA=25°C
'AS881A
TA=MIN to MAX
SN54AS881A SN74AS881A
c
2:
Any
C n =4.5V, M=4.5 V,
MIN Typt MAX MIN Typt MAX MIN Typt MAX
«
tpd p 50=53=4.5 V, 51 =52=0 V, 8 2 10 19 2 10 15 ns C/)
A or B -J
Any
Equality (Ai = Bi or Ai*Bi)
C n =4.5 V, M=4.5 V,
50=53=4.5 V, S1 =52=0 V, 10 2 12 24 12 18 ns
«
tpd Cn +4 2
AorS
Equality (Ai = Bi or Ai*Bi)
C n =4.5 V, M=4.5 V,
Any
tpd
A or B
p 52 =4.5 V, 50 =51 =53 =0 V, 8 2 10 19 2 10 15 ns
(Ai =Bi = H or Ai or Bi =Ll
Cn =4.5 V, M=4.5 V,
Any
tpd Cn +4 52=4.5 V, 50=51 =53=0 V, 11 2 13 25 2 13 19 ns
A or B (Ai=Bi=H or Ai or Bi=Ll
tpd=tpHL or tpLH
t All typical values are at Vee = 5 V, T A = 25°C.
83
TEXAS 2-181
INSTRUMENTS
TYPES SN54AS181A, SN54AS881A, SN74AS181A,SN74AS881A

SUM MODE TEST TABLE
FUNCTION INPUTS: SO = S3 = 4.5 V. Sl = S2 = M = 0 V
OTHER INPUT
INPUT OTHER DATA INPUTS OUTPUT OUTPUT
SAME BIT
PARAMETER UNDER UNDER WAVEFORM
APPLY APPLY APPLY APPLY
TEST TEST (SEE NOTE AI
4.5V GND 4.5 V GND
IPLH Remaining
Ai B, None Cn 1', In·Phase
IPHL A andB
IPLH Remaining
Bi Ai None Cn F, In·Phase
IPHL AandB
IPLH Remaining p
Ai Hi None None In·Phase
IPHL A and 8. C n
IPLH Remaining p
8, A, None None In·Phase
IPHL AandB.C n
IPLH Remaining Remaining
A, None 6, G In·Phase
IPHL 8 A. C n
IPLH Rema,ning Remaining
8, None A, G In·Phase
IPHL 8 A. C n
IPLH All All Any F
Cn None None In·Phase
IPHL A B or C.,+4
A, None 8, C n +4 OUI·ol·Phase
..
IPHL B A. C n
B, None A, C n +4 OUI·ol·Phase
IPHL B A.C n
DIFF MODE TEST TABLE

FUNCTION INPUTS: Sl = S2 = 4.5 V. SO = S3 = M = 0 V
OTHER INPUT
l> INPUT
SAME BIT
OTHER DATA INPUTS OUTPUT OUTPUT
r- PARAMETER UNDER UNDER WAVEFORM
en TEST
APPLY
4.5 V
APPLY
GND
APPLY
4.5 V
APPLY
GND
TEST (SEE NOTE AI
l> IpLH
A, None 8,
Remalntng Remaln,ng
F, In·Phasp.
2 IpHL A B. C n
C IpLH
8, A, None
Remaining Rema,n,ng
F, Oul·ol·Phase
IPHL A B. C n
l> IpLH Remaining
p
0 IPHL
A, None 8, None
A andB. C n
In·Phase
Q IpLH
IPHL
8, A, None None
Remaining
A andB. C n
p- Oul·ol·Phase
'::0 Rema,ning
0 IPLH
A, 6, None None
Ii andB. Cn
G In·Phase
C IpHL
Remaining
~
IpLH
tl, None A, None G OUI·ol·Phase
IpHL A andB. C n
(J) Remaining Rema,n,ng
IpLH
A, None 8, A ~ B In·Phase
IPHL A B.C n
IPLH Remaining Remain,ng
8, A, None A = B Oul·ol Phase
IPHL A B.C n
IpLH All Cn +4
Cn None None None In·Phase
IpHL A andB or any I'
IpLH Remaining
A, 8, None None C n +4 Oul·al·Phase
IpHL A.B.C n
IpLH Remaining
6i None A, Nane C n +4 In ·Phase
IpHL A.B.C n
NOTE A: For load circuit and voltage waveforms. see page 1-12.
1~
2-182 TEXAS
INSTRUMENTS
ARITHMETIC LOGIC UNITSJFUNCTION GENERATORS
LOGIC MODE TEST TABLE

FUNCTION INPUTS: S1 = S2 = M = 4.5 V. SO = S3 = 0 V
OTHER INPUT
SAME BIT
4.5V GND 4.5V GND
tpLH Remaining
Ai B None None Fi Out-ot-Phase
tPHL A and B. Cn
tpLH Remaining
tpHL
Bi Ai None None
A andS. Cn Fi Out-ot·Phase
INPUT BITS EQUAL/NOT EQUAL TEST TABLE

FUNCTION INPUTS: SO=S3=M=4.5 V. S1 =S2=0 V
OTHER INPUT
SAME BIT
4.5V GND 4.5V GND
tPLH Remaining
Ai Bi None None P Out-ot-Phase
tpHL A and B. Cn
tpLH Remaining
Bi Ai None None P Out-ot-Phase
tpHL A and B. Cn
tpLH Remaining
Ai None Bi None P In-Phase
tpHL if. and 13. Cn
tpLH Remaining
Bi None Ai None P In-Phase
tpHL A and B. Cn (I'J
tpLH Remaining
tpHL
Ai Bi None
A and B. Cn
None Cn +4 In-Phase !::
tpLH Remaining ::::>
Bi Ai None None Cn +4 In-Phase (J
tpHL
tpLH
A and B. Cn
Remaining
a:
Ai None Bi None Cn +4 Out-ot-Phase (J
tpHL A and B. Cn
tpLH Remaining (I'J
Bi None Ai None Cn +4 Out-ot-Phase
tpHL A and B. Cn <t
INPUT PAIRS HIGH/NOT HIGH TEST TABLE C
FUNCTION INPUTS: S2=M=4.5 V. SO=S1 =S3= OV 2
<t
OTHER INPUT (I'J
INPUT OTHER DATA INPUTS OUTPUT OUTPUT -oJ
SAME BIT
PARAMETER UNDER
UNDER
TEST
WAVEFORM
<t
TEST (SEE NOTE AI
4.5 V GND 4.5V GND
tpLH Remaining Remaining
Ai Bi None is In-Phase
tpHL A.C n B
tpLH Remaining Remaining p
Hi Ai None In-Phase
tpHL e.C n A
Ai Bi None
B
Cn +4 Out-ot-Phase
tpHL A.C n
Bi Ai None Cn +4 Out-ot-Phase
tpHL a.C n A
NOTE A: For load circuit and voltage waveforms, see page 1-12.
!83
TEXAS 2-183
INSTRUMENTS
..
»
r-
t/)
»
2
C
»
t/)
o
::JJ
o
c
=4
en
2-184
LOOK-AHEAD CARRY GENERATOR
02661, DECEMBER 1983
• High-Speed Replacement for the 'S182 SN54AS182 . . . JPACKAGE

SN74AS182 . . . N PACKAGE
• Offers Carry Functions in a Compatible Form (TOP VIEW)
for Direct Connections to the ALU
VCC
• Cascadable to Perform Look-Ahead Across P2
n-Bit Adders G2
• Dependable Texas Instruments Quality and Cn
Reliability Cn + x
Cn + y
G
PIN DESIGNATIONS
GND-...;~.--;J-' C n + z
ALTERNATIVE DESIGNATIONS t FUNCTION
GO. G1. G2. G3 GO. G1. G2. G3 Carry Generate Inputs
PO. P1. P2. P3 PO. P1. P2. P3 Carry Propagate Inputs SN54AS182 .. , FH PACKAGE
en Cn Carry Input SN74AS182 . . . FN PACKAGE
C n + x • C n + y• C"n+x, C n + y • (TOP VIEW)
Carry Outputs
Cn + z Cn + z U
G y Carry Generate Output ........ U UN
I~I(!} Z >I~
P X Carry Propagate Output
Vee Supply Voltage
GND Ground <32
PO Cn + x
t Interpretations are illustrated in connection with the Function Tables for NC NC
the 'AS181A and 'AS881A. <33 Cn + y
P3 Cn
description
I~ 0 U NI(!}
The 'AS 182 look-ahead carry generators are Z Z +
(!) c C/)
capable of anticipating a carry across four binary U
adders or group of adders. They are cascadable NC - No internal connection t::
to perform full look-ahead across n-bit adders. :::>
(.)
This generator, when used in conjunction with the' AS181 or 'AS881 Arithmetic Logic Unit ALU, provides
high-speed carry look-ahead capability for any word length. The 'AS 182 generates the look-ahead
a::
(anticipated carry) across a group of four ALUs. In addition, other carry look-ahead circuits may be employed
(.)
to anticipate carry-across sections of four look-ahead packages up to n-bits. The method of cascading C/)
, AS 182 circuits to perform multilevel look-ahead is illustrated under the typical application data. «
The carry functions (inputs, outputs, generate, and propagate) of the look-ahead generators are implemented o
in the compatible forms for direct connections to the ALU. Reinterpretations of carry functions as explained z
on the 'AS 181 A and ' AS881 A data sheet are also applicable to and compatible with the look-ahead
generator. Logic equations for the ' AS 182 are:
«
C/)
..J
C n + x = GO +
C n + y = G1 +
PO
P1
Cn
GO + P1 PO C n
Cn +x = YO
(XO + Cn)
Cn + y = Y1
[X1 + YO (XO + C n )]
«
C n + z = G2 + P2 G1 + P2 P1 GO + P2 P1 PO C n or Cn + z = Y2
{X2 + Y1 [X1 + YO (XO + Cn)]}
q = G3 + P3 G2 + P3 P2 G1 + P3 P2 P1 GO Y=Y3 (X3+Y2) (X3+X2+Y1) (X3+X2 +X1 +YO)
p= P3 P2 P1 PO X = X3 + X2 + X 1 + XO

283
Thia page contain. Information on e product under
davelopment. Tex•• lnlttumenta r...rves the right to
TEXAS . 2-185
change o. discontinue this product without notice. INSTRUMENTS
LOOK·AHEAD CARRY GENERATOR
FUNCTION TABLE FOR G OUTPUT FUNCTION TABLE

INPUTS OUTPUT FUNCTION TABLE FOR Cn + x OUTPUT
G3 G2 Gl GO P3 P2 Pl G FOR ji OUTPUT INPUTS OUTPUT
L X X X X X X L INPUTS OUTPUT GO PO Cn Cn + x
X L X X L X X L P3 P2 Pl PO Ii L X X H
X X L X L L X L L L L L L X L H H
X X X L L L L L All other All other
H L
All other combinations H combinations combinations
FUNCTION TABLE C n + v OUTPUT FUNCTION TABLE FOR Cn + z OUTPUT

INPUTS OUTPUT INPUTS OUTPUT
Gl GO Pl PO Cn Cn + G2 Gl GO P2 Pl PO Cn Cn + z
v
L X X X X H L X X X X X X H
X L L X X H X L X L X X X H
X X L L H H X X L L L X X H
All other X X X L L L H H
L
combinations All other combinations L
H : High-level, L : Low-level, : Irrelevant

Any inputs not shown in a given table are irrelevant with respect to that output.
logic diagram (positive logic) logic symbols
.---f~~~~~[:)- ____ -,-(7'-!.) l' or X

CPG
CI coo (12) Cn +x
po CPO
COl
GO
-.J
CGO
1'1 CPl CO2
Gl CGl
~ CP2 CP
r- CG2
CJ)
P30rX3~(56~)-+~~~~-+1 CP3 CG
l> G30rY3~(~)-+1-r--r~~1-~ CG3
;2
C OR
l>
(J) CPG
C') 1,2
Cn (131 Zl C n +x
::IJ 3
C') P2orX2~(1_5~)~~~~1-r1 1.2.4
c G2orY2~(1~4~)~~--+1~~ 3.4
5 C n +v
=t
CIJ
1,2.4.6
3.4.6
Cn +z
5.6
7
l'
- (2)
~lorXl~(l~)-+~--~+-~~~
GlorYl~-+---~+-~~ P3 0
03
Pin numbers shown are for J and N packages only.
128
2-186 TEXAS
INSTRUMENTS
Supply voltage, Vee .........' ................................................ 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 182 ....................... - 55 DC to 125 DC
SN74AS182 .......................... oDe to 70 Dee
Storage temperature range ...... '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 DC to 150 DC

SN54AS182 SN74AS182
UNIT
TA Operating free-air temperature -55 125 0 70° °e
electrical characteristics over recommended operating free-air temperature range (unless otherwise
noted)
SN54AS182 SN74AS182
PARAMETER TEST CONDITIONS 'UNIT
MIN TVpt MAX MIN TVpt MAX
VIK Vec = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V. IOH'= -2 rnA Vee- 2 Vee- 2 V
VOL Vec = 4.5 V, 10l = 20 rnA 0.3 0.5 0.3 0.5 V
Cn 0.1 0.1
P3 0.2 0.2
en
P2 0.3 0.3 !::
II
PO, Pl, G3
VCC = 5.5 V, VI =7.0 V
0.4 0.4
rnA ::::>
GO, G2 0.7 0.7 u
G'1 0.8 0.8
a:
Cn 0.02 0.02 U
P3 0.04 0.04 en
IIH
P2
VCC = 5.5 V. VI = 2.7 V
0.06 0.06
rnA «
PO. Pl. G3
Gl. G2
0.08
0.14
0.08
0.14
c
2
131
Cn
0.16
-0.5
0.16
-0.5
«
P3 -1 -1 en
..oJ
III
P2
P2. Pl. G3
VCC = 5.5 V. VI = 0.4 V
-1.5
-2
-1.5
-2
rnA «
GO. G2 - 3.5 -3.5
Gl -4 -4
lot VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
leCH 17 17
Vee = 5.5 V rnA
leCl 23 23

tThe output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current. lOS.
283
\ TEXAS 2-187
INSTRUMENTS

Vcc = 4,5 V to 5,5 V,
Cl = 50 pF,
FROM TI Rl = 500 fl,
PARAMETER UNIT
SN54AS182 SN74AS182
MIN Typf MAX MIN Typf MAX
tPLH Cn + y , Cn + y 5 5
Cn ns
tPHl Cn + z 5 5
tPLH Cn + x , Cn + y 5 5
PorG ns
tpHl Cn + z 5 5
tpLH 6 6
j5 or G G ns
tpHL 5 5
tPlH j5' j5'
5 5
ns
tPHL 5 5

'AS181A, 'AS881 A
A
Cn+x
'AS182
FIGURE 1-THE 'AS182 IN A 64-BIT LOOK-AHEAD CARRY CIRCUIT
128
2-188 . TEXAS
INSTRUMENlS
SYNCHRONOUS 4·811 UP/DOWN DECADE AND BINARY COUNTERS
02661, DECEMBER 1982 - REVISED DECEMBER 1983
SN54ALS190,SN54ALS191 • J PACKAGE
• Single Down/Up Count Control Line SN74ALS190,SN74ALS191 • N PACKAGE
ITOPVIEW)
• Look-Ahead Circuitry Enhances Speed of Cascaded
Counters S VCC
QS A
• Fully Synchronous in Count Modes QA CLK
• Asynchronously Presettable with Load Control CTEN RCO
D/D MAX/MIN
• Package Options Include Both Plastic and Ceramic QC LOAD
Chip Carriers in Addition to Plastic and Ceramic DIPS QD C
• Dependable Texas Instruments Quality and Reliability GND D
"""'-----'-
SN54ALS190. SN54ALS191 ... FH PACKAGE

descriptions SN74ALS190. SN74ALS191 ... FN PACKAGE
The 'ALS 1 90 and 'ALS 191 are synchronous, reversible (TOP VIEW)
up/down counters. The' ALS 190 is a 4-bit decade counter and U
co U U
the 'ALS 191 is a 4-bit binary counter. Synchronous counting dcoZ>4:
operation is provided by having all flip-flops clocked
simultaneously so that the outputs change coincident with each QA 4
other when so instructed by the steering logic. This mode of CTEN 5
operation eliminates the output counting spikes normally NC 6 NC
associated with asynchronous (ripple clock) counters. D/O MAX/MIN
The outputs of the four flip-flops are triggered on a low-to-high- QC 8
level transition of the clock input if the enable input (CTEN) is 9 1011 1213
low. A high at CTEN inhibits counting. The direction of the count 00 U 0 U

is determined by the level of the down/up (DiD'! input. When Diu dZZ
(.!)
is low. the counter counts up and when Diu is high. it counts
down. NC - no internal connection. en
These counters feature a fully independent clock circuit. Changes at the control inputs (CTEN and DiU) that will modify.
!::
the operating mode have no effect on the contents of the counter until clocking occurs. The function of the counter will
:::»
()
be dictated solely by the condition meeting the stable setup and hold times. a:
These counters are fully programmable; that is. the outputs may each be preset to either level by placing a low on the ()
load input and entering the desired data at the data inputs. The output will change to agree with the data inputs
independently of the level of the clock input. This feature allows the counters to be used as modulo-N dividers by
en
simply modifying the count length with the preset inputs.
<C
The CLK. 0/0. and LOAD inputs are buffered to lower the drive requirement. which significantly reduces the loading
C
:2
on. or current required by. clock drivers. etc .• for long parallel words.
<C
Two outputs have been made available to perform the cascading function: ripple clock and maximum/minimum count.
The latter output produces a high-level output pulse with a duration approximately equal to one complete cycle of the
en
...J
clock while the count is zero (all outputs low) counting down or maximum (9 or 15) counting up. The riPRle clock <C
output produces a lOW-level output pulse under those same conditions but only while the clock input is low. The
counters can be easily cascaded by feeding the ripple clock output to the enable input of the succeeding counter if
parallel clocking is used. or to the clock input if parallel enabling is used. The maximum/minimum count output can be
used to accomplish look-ahead for high-speed operation.
The SN54ALS190 and SN54ALS191 are characterized for operation over the full military temperature range of
- 55 °C to 1 25 °C. The SN7 4ALS 190 and SN7 4ALS 191 are characterized for operation from O°C to 70 0 C.
Copyright © 1982.by Texas Instruments Incorporated

283
TEXAS 2-189
INSTRUMENTS
'ALS190 logic symbol
1121
2(CT=OIZ6 MAX/MIN
3(CT-9IZ6
[1)
[2)
[4)
[8)
'ALS 190 logic diagram (positive logic)
12E
2-190 TEXAS
INSTRUMENTS
SYNCHRONOUS 4·BIT UPIDOWN BINARY COUNTERS
(12) MAX/MIN
(1\
(2\
(4\
(B\
'ALS 191 logic diagram (positive logic)
1121
MAXIMIN
(4)
7ci1i}-
(13)
(5)
DIU
(14)
ClK
19 r;---El
A
~ -~l
>-<i>C1
OA
BIll
en
(1) """'I I C:
B
D ::J
~
4:~~ Os
~~
U
>---C >C1
rx:
1-- ./
r + ..... rL~ u
en
'-- D "" I
I
I
«
c
-
1: 0
C
Z
L.:s ~ QC
«
~-~ rL-
~
.....-<~C1
en
rl- -tL.......'
"" I
JI
-I
«
'-- D I
-
"'1 0 ~ ~--
-
-L. L-t~
iP7>e.r
---;:'-<
~s
i' ~
---
~ 00
'l" I I
La
!B3
TEXAS 2-191
INSTRUMENTS
typical load, count, and inhibit sequences
'ALS190

1. Load (preset) to BCD seven.
2. Count up to eight, nine (maximum). zero, one, and two.
3. Inhibit.
4. Count down to one, zero (minimum), nine, eight, and seven.
LOAD~
i
A.J L
-
DATA
B.J I
L.
'NPUTS
C.J
I
L
D ,r
CLOCK
,
-----1--"
DIU ____ ,___ ,1-1_ _ _ _ _ _ _ _ _ _ _ _--'
I 1I
----1--71 1
C'i'EN ____1__ 11-'1__________...
I
, I
0A ___ ....J 'I,
OB----:--!l
___ ....J
1 :
, ...._ _ _ _ _ _ _ _ _.... r---
!
I I
Oc----;--I1 I
___ ....J i-----------------------~~---------~·
1 ...
----,
oo ____ L--iJ11 ~
I I
MAX'MIN - - - - , ' , ,---, ..,
____ ...
I_~~--~! IL.._ _ _ _ _ _~------~---~! 1...._ _ _ _ _ _ _ _ __ _
RCO ----I
___ -.J ,I
I U' ,I , u
I
: 7 I 1 9 2 I 1 0 9 8
~
I I.. I·....----COUNT UP - - -... 1- INHIBIT--I I--- ·1
COUNT DOWN - - - -..
LOAD
128
2-192 TEXAS
INSTRUMENTS
SYNCHRONOUS 4·BIT UPIDOWN BINARY COUNTERS
typical load, count, and inhibit sequences
'ALS191

1. Load (preset) to binary thirteen.
2. Count up to fourteen, fifteen (maximum), zero, one, and two.
3. Inhibit.
4. Count down to one, zero (minimum). fifteen, fourteen, and thirteen.
lOAD-U
A..J :
I
I
,--
L..._
I
r-
B
I
I
,-- 1-
,--
DATA 1
I
INPUTS
C.J I.
I L._
D-.J
I
,--
L._
ClK
--- --,
D/u _ _ _I_ '-1_ _ _ _ _ _ _ _ _ _ _ _ ---1
en
!::
::>
-----, 1
CTEN _ _ _1 _ _ ,
I I
C,)
1 '.1----------.
1
. 1 I
.. a:
C,)
I
I:
I en
«
°B -___
- .,
L-iJI ....- - - - - - . L c
z
0c -_ _
- I
.....J «
en
...J
- --I
°0 __ ...J «
MAXIM I N _- -__
..." r-:--1 r-:--1
~.~~~, I~------------~~--I ,~ ____________
--I
Rca -_ _ ...J
: 13 14
U
15 0 I 2 2
U 15 14 13
~
I I. . o----COUNT U P - - -...I-INHIBIT--I I--- COUNT DOWN ·1
LOAD
83
TEXAS 2-193
INSfRUMENTS
SYNCHRONOUS 4-BfT UP/DOWN DECADE AND BINARY COUNTERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AlS190, SN54AlS191 . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74AlS190,SN74AlS191 . . . . . . . . • . . . . . . . . . . . . . ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " - 65 DC to 1 50 DC

. SN54ALS190 SN74ALS190
'AlS190 0 20 0 25
'AlS19l 0 25 0 30
ClK high or low

I 'AlS190 25 20
tw Pulse duration J 'AlS19l 20 16.5 ns
LOAD low 25 20
Data before lOAD! 25 20
CTEN before CLK! 25 20
tsu Setup time ns
DIU before ClK! 20 20
~
TITAD inactive before ClK I 20 20
Data after mAD! 5 5
»
r-
th Hold time CTEN after ClK I
DIU after CLK I
0
0
0
0
ns
rJ) TA Operating free-air temperature -55 125 0 70 °c
»
2
C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
»
rJ) PARAMETER TEST CONDITIONS
SN54ALS190
SN54ALS191
SN74ALS190
SN74ALS191
UNIT
n
-
:zJ
n
VIK
VOH
Vce = 4.5 V,
Vce = 4.5 V to 5.5 V,
Vce = 4.5 V,
II = -18 rnA
10H = -0.4 rnA
10l = 4 rnA
vee- 2
0.25
..:. 1.5
0.4
vee- 2
0.25
- 1.5
0.4
V
V
c VOL
VCC = 4.5 V 10l = 8 rnA 0.35 0.5
V
=f II Vec = 5.5 V, VI = 7 V 0.1 0.1 rnA

til IIH VCC = 5.5 V, VI = 2.7 V 20 20 p.A
I eTEN or ClK Vce = 5.5 V, VI = 0.4 V
-0.2 -0.2
rnA
III
I All others -0.1 -0.1
10:1: VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
ICC Vec =: 5.5 V, All inputs at 0 V 12 22 12 22 rnA
t All typical values are at Vee = 5 V.

TA = 25°C.
12
2-194 TEXAS
INSTRUMENlS
Vcc = 4.5 V to 5.5 V, '

CL = 50 pF,
RL = 500 Q,
FROM TO
(INPUT) (OUTPUT)
MIN MAX MIN MAX
'ALS190 20 25
f max MHz
'ALS191 25 30
tpLH 8 34 8 30
LOAD Any Q ns
tpHL 8 34 8 30
tpLH 4 25 4 21
A, B,C,D Any Q ns
tpHL 4 25 4 . 21
tpLH 5 24 5 20
CLK RCO ns
tpHL 5 24 5 20
tpLH 3 22 3 18
CLK Any Q ns
tpHL 3 22 3 18
tpLH 8 34 8 31
CLK MAX/MIN ns
tpHL 8 34 8 31
tpLH 15 42 15 37
Diu RCa ns
tpHL 10 33 10 28
tpLH 8 30 8 25
Diu MAX/MIN ns
tpHL 8 30 8 25
tpLH 4 21 4 18
CTEN RCa ns
tpHL 4 21 4 18
(/)
!::
:::>
()
a:
()
(/)
<t
C
z
<t
(/)
...J
<t
33
TEXAS 2-195
INSTRUMENTS
2-196
SYNCHRONOUS 4·81T UP/DOWN COUNTERS (DUAL CLOCK WITH CLEAR)
D2661, DECEMBER 1982-REVISED DECEMBER 1983
• Look-Ahead Circuitry Enhances Cascaded Counters SN54ALS192,SN54ALS193. J PACKAGE

SN74ALS192,SN74ALS193 . N PACKAGE
• Fully Synchronous in Count Modes
(TOPVIEWI
• Parallel Asynchronous Load for Modulo-N Count
Lengths 8 VCC
• Asynchronous Clear Q8 A
QA CLR
• Package Options Include Both Plastic and Ceramic DOWN BO
Chip Carriers in Addition to Plastic and Ceramic DIPs UP CO
• Dependable Texas Instruments Quality and Reliability QC LOAD
QD C
description GND - " "_ _. . ; . J - D
The .'ALS192 and 'ALS193 are synchronous, reversible SN54ALS192,SN54ALS193 FH PACKAGE

up/down counters. The 'ALS192 is a 4-bit decade counter and SN74ALS192,SN74ALS193 FN PACKAGE
the 'ALS193 is a 4-bit binary counter. Synchronous operation is (TOP VIEWI
provided by having all flip-flops clocked simultaneously so that
the outputs change coincidently with each other when so u
CD U u
instructed by the steering logic. This mode of operation OCDZ>«
. eliminates the output counting spikes normally associated with 3 2 1 20 19
asynchronous (ripple clock) counters. QA CLR
DOWN BO
The outputs of the four flip-flops are triggered by a low-to-high-
NC NC
level transition of either count (clock) input (Up or Down). The
direction of counting is determined by which count input is
UP CO
QC LOAD
pulsed while the other count input is high.
All four counters are fully programmable; that is, each output
00 U 0 U
may be preset to either level by placing a Iowan the load input OZZ
and entering the desired data at the data inputs. The output will
C)
en
change to agree with the data inputs independently of the count t::
pulses. This feature allows the counters to be used as modulo-N
NC - no internal connection.
:::>
dividers by simply modifying the count length with the preset (J
inputs. a:
(J
A clear input has been provided that forces all outputs to the low level when a high level is applied. The clear function is en
independent of the count and the load inputs. The clock, count, and load inputs are buffered to lower the drive cd:
requirements. This significantly reduces the loading on clock drivers, etc., for long parallel words. C
These counters were designed to be cascaded without the need for external circuitry. The borrow output (80) Z
produces a low-level pulse while the count is zero (all outputs low) and the count-down input is low. Similarly, the carry cd:
output (CO) produces a low-level pulse while the count is maximum (9 or 15) and the count-up input is low. The en
counters can then be easily cascaded by feeding the borrow and carry outputs to the count-down and count-up inputs, ..J
respectively, of the succeeding counter. cd:
The SN54ALS192 and SN54ALS193 are characterized for operation over the full military temperature range of
-55°C to 125°C. The SN74ALS192 and SN74ALS193 are characterized for operation from O°C to 70°C.
Copyright © 1982 by Texas Instruments Incorporated·

33
TEXAS 2-197
INSTRUMENTS
SYNCHRONOUS 4·81T UP/DOWN DECADE COUNTERS (DUAL CLOCK WITH CLEAR)

CTRDIV10
CLR (141 CT-O
UP (51
(8)
'ALS192 logic diagram (positive logic)
L (121
,-J
(131
CLR ~
(51 ...... ~~
~
UP
(41
LU
DOWN
LOAD
~
A
(151 ;
- (31
~~
- ~
S f----
r--c
r:
>Cl
10
;:[)
~
1~F-]
(11 ~ 1
l> ~~ ~:-- (21
r- S I--
~ ~~7L~
0 "'7 r----c>Cl
l>
2
C
l>
9 ;:u
.....,. I
I
1
;:~
~
0
(101
0 C
~r=tJ ~~ (61
~ -~ rL~
::D 5 r--- Oc
~pCl
0
c
=i >- ~
.....,.
0
(91
-
R->
L
I
J
0
~t=L-J
.~~~ 00
~~ ~ . . rL 1
.,-+-- L-c I> C1
~
I
QJ
128
2-198 TEXAS
INSTRUMENTS
SYNCHRONOUS 4·BIT UP/DOWN BINARY COUNTERS (DUAL CLOCK WITH CLEAR)

CTRDIV16
CLR 1141 CT=O
(51
UP
'ALS193 logic diagrams (positive logic)
(121
I
""""- (131
4~
(141 "
CLR
v
(51
UP
(41
1>-
..-
lU-
DOWN
A
~
(151
~ R-J-
(11
FU
-
=t..J
~
.....,..
r---
5
~ >Cl
r:
l~~
~ OA
10
T
..en
!:::
&
>
.- ...... Lc~~ OB :>
~-4>Cl (.)
~ FLJ
a:
1'-'/
......,.
7L~ (.)
I I
en
I
«
c
1101
-
FU c
+ ~~~ 7L~
k-;-~ Oc
~I>Cl
2:
«
o
(91
9 R->
'I I
I
1
en
..J
«
~FL--J kr--- m
·~~t;
'Ii aD
I
-
CLJ
'I I
I
1
TEXAS . 2-199
INSTRUMENTS
SYNCHRONOUS 4·811 UP/DOWN DECADE COUNTERS (DUAL CLOCK WITH' CLEAR)
typical clear, load, and count sequence
'ALS192
1. Clear outputs to zero.

2. Load (preset) to BCD seven.
3. Count up to eight, nine, carry, zero, one, and two.
4. Count down to one, zero, borrow, nine, eight, and seven.
CLR ~~------------------------------------
LOAD
U
I I 'I
A --1-'--1'1
_ _ _ _ --.J L - _
1 I I 1
-_ _
----1'1-
,_,_-, L--
..
I I I 1
DATA
c -----.,-
_ _ I_I_--.J L-. _ _ _
0 -_ _
- 1_I' 'Ir -
-1_--
_ - 'L......J _
I
UP -----,---
I 1
l>
r- -----'-1--
en DOWN
-
- - -_ _
- _I_I - '_I_-l
- - -,--------------,
l> 1 ,
,----..,
:2 QA
1
C
l>
en OUTPUTS
QH
=:1L.-_-"
I
1
~----------~~,
1
0 °c
=:1 ~----------------------------~~
,
=:1....____--'
'-1-----'
::D
0 °0
~
c
=i
en
CO
u
So
U 1
1 21 1 71
SE~UENCE
ILLUSTRATED r--- 8 9 0
COUNT UP
1
--, r---1 0 9 8
COUNT DOWN - - ,
NOTES: A. Clear overrides load, data, and count inputs.

B. When counting up, count-down input must be high; when counting down, count-up input must be high.
1283
2-200
TEXAS
INSTRUMENTS
SYNCHRONOUS 4·BIT UP/DOWN BINARY COUNTERS (DUAL CLOCK WITH CLEAR)
typical.clear, load, and count sequences
'ALS193
1. Clear outputs to zero.

2. Load (preset) to binary thirteen.
3. Count up to fourteen, fifteen, carry, zero, one, and two.
4. Count down to one, zero, borrow, fifteen, fourteen, and thirtee'n,
CLR
--1l~ __________________________________
LOAD
I I
U
I,
A _ _ _ _ --.J L--
--I-i-r-l-
I'
--'-1--' r-
_ _ _ _ _ L...J_
I'
----,.
DATA
-
_-_-
" - ---'r
,_,_
" l-
L -
11 "
[)
==1:=1= =-r'L-- 1 ,
UP -------
-- -1-,--1-,--
I' "
- - - - - - - ......--------'---------.
en
!::
DOWN
__1_, __1_'_.1 :::>
I, 1
r-----., CJ
a:
=.JI-___
I
~_~ ~
1 CJ
=,
Oil en
OUTPUTS I
~---'- <t
°c
00 =--, ,'- ----'
r----------.L..-_____---.;.____---I
C
z
<t
en
u -oJ
<t
, , LJ '
I I 1
r--- ~ r---
14 15 0 1 0 15 14 13
SEOUENCE
ILLUSTRATED COUNT UP COUNT DOWN - - - ,
NOTES: A. Clear overrides load, data, and count inputs.

B. When counting up, count,down input must be high; when counting down, count,up Input must be high.
TEXAS 2-201
INSTRUMENTS
Supply voltage, Vee ............................................... '. . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS192, SN54ALS193 . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS192,SN74ALS193 . . . . . . . . . . . . . . . . . . . . . . Qoeto700e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 de to 15'0 °e

'ALS192 0 20 0 25
'ALS193 0 25 0 30-
eLR high 10 10
ns
LOAD low 25 20
tw Pulse duration
I 'ALS192 25 20
UP or DOWN high or low I'ALS 193 20 16.5
ns
Data before LOAD I 25 20
16 tsu Setup time eLR inactive before UPI or DOWNI

LOAD inactive before UPI or DOWNI
Data after LOAD I
20
20
5
20
20
5
ns
l> th Hold time UP high after DOWN I 0 0 ns

r-
en DOWN high after UPI 0 0
l>
2
C
l> electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
en SN54ALS192 SN74ALS192
Q PARAMETER TEST CONDITIONS

SN54ALS193
MIN Typt MAX
SN74ALS193
MIN TYpt MAX
UNIT
::D
o VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
c VOH Vee = 4.5 V to
= 4.5 V,
5.5 V, 10H = -0.4 mA
10L = 4 mA
VCC- 2 vCC- 2 V
=i VOL
Vee 0.25 0.4 0.25 0.4
V
en Vee = 4.5 V 10L = 8 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL
I UP, DOWN Vee = 5.5 V, VI = 0.4 V
-0.2 -0.2
mA
I All others -0.1 -0.1
10* Vee = 5.5 V, Vo = 2.25 V -:-30 -112 -30 -112 mA
ICC Vee = 5.5 V, See Note 1 12 22 12 22 mA

NOTE1: ICC is measured with the clear and load inputs grounded, and all other inputs at 4.5 V.
12f
2-202 TEXAS
INSTRUMENTS
Vee = 4.5 V to 5.5 V,

el = 50 pF,
Rl = 500 Q,
FROM TO
(INPUT) (OUTPUT)
MIN MAX MIN MAX
'AlS192 20 25
f max MHz
'ALS193 25 30
tpLH 4 19 4 16
Up CO ns
tpHL 5 21 5 18
tpLH 4 19 4 16
Down BO ns
tpHL 5 21 5 18
tpLH 4 23 4 19
Up or Down Any Q ns
tpHL 4 20 4 17
tpLH 8 35 8 30
Lc5Ao Any Q
31 8 28
ns
tpHL 8
tpHL CLR Any Q 5 20 5 17 ns
NOTE 2: For load circuit and voltage waveforms, see page 1·12 ...
en
!::
:::J
U
a:
U
en
«
c
z
«
en
..J
«
TEXAS 2-203
INSTRUMENTS
~
l>
r-
en
l>
2
C
l>
en
Q
:1'J
o
c
=i
en
2-204
4·BIT BIDIRECTIONAL UNIVERSAL SHIFT REGISTERS
D2661. DECEMBER 1983
• Parallel-to-Serial, Serial-to-Parallel SN54194 ..• J PACKAGE

Conversions SN74AS194 ... N PACKAGE
(TOP VIEW)
• Left or Right Shifts
ClR VCC
• Parallel Synchronous Loading SR SER QA
A QS
• Direct Overriding Clear
S QC
• Temporary Data Latching Capability C aD
D ClK
Reliability
Sl SER S1
GND SO
description
These bidirectional shift registers feature parallel SN54AS194 ... FH PACKAGE
SN74AS194 ... FN PACKAGE
outputs, right-shift and left-shift serial inputs,
(TOP VIEW)
operating-mode-control inputs, and a direct
a:
overriding clear line. The register has four distinct W
modes of operation, namely: (J)1a: U

a:...JUU«
(J)uz>d
Inhibit clock (temporary data latch/do nothing
3 2 1
Shift-right (in the direction QA toward QD)
Shift-left (in the direction QD toward QA)
as
Qc
Parallel (broadside) load
NC
Synchronous parallel loading is accomplished by aD
applying the four bits of data and taking both ClK
mode control inputs, SO and S 1, high. The data 9 1011 1213
are loaded into the associated flip-flops and a:ouo.-
wzz(J)(J)
appear at the outputs after the positive transition
of the clock input. During loading, serial data
(J)t!)
...J
en
flow is inhibited.
(J) J:::
NC - No internal connection ::>
Shift-right is accomplished synchronously with u
the rising edge of the clock pulse when SO is high a:
and S 1 is low. Serial data for this mode is entered u
at the shift-right data input. When SO is low and
en
S 1 is high, data shifts left synchronously and
new data is entered at the shift-left serial inputs. «
Clocking of the flip-flop is inhibited. when both c
mode control inputs are low. 2
The SN54AS194 is characterized for operation
«
over the full military temperature range of en
..J
-55°C to 125°C. The SN74AS194 is
characterized for operation from 0 °C to 70°C. «

development. Taxas Instruments reserves the right to TEXAS 2-205
change or dilcontlnue this product without notice. INSTRUMENTS
FUNCTION TABLE
INPUTS OUTPUTS H = high level (steady state)
MODE SERIAL PARALLEL L = low level (steady state)
CLEAR CLOCK QA QB Qc QD X = irrelevant (any input. including tran-
S1 SO LEFT RIGHT A B C 0
sitions)
L X X X X X X X X X L L L L t = transition from low to high level
H X X L X X X X X X QAO QBO QCO QDO a. b. c. d = the level of steady-state input at
inputs A. B. C. or D. respectively.
H H H t X X a b c d a b c d
0AO. 0BO. OeD. aDO = the level of 0A.
H L H t X H X X X X H QAn QBn QCn 0B. DC. or 00. respectively. before the
H L H t X L X X X X L QAn QBn QCn indicated steady-state input conditions
were established.
H H L t H X X X X X QBn QCn QDn H
0An. 0Bn. Den. 0Dn = the level of 0A.
H H L t L X X X X X QBn QCn QDn L 0B. 0e. respectively. before the most-
H L L X X X X X X X QAO QBO QCO QDO recent t transition of the clock.
typical clear, load, right-shift, inhibit, and clear sequences
CLOCK
MODE
CONTROL
{so ::J :
I
INPUTS S1 ::rf1..--:~----------!
CLEAR ~:
I I
_-+1_.:.:_"":'...111
1m SERIAL { R
DATA
INPUTS L
: I
--;.!--io:---:----------~-~
»
r-
I I
A ~~~_ _ _ _ _ _ _ _ _~_~_ _ _ _ _ _ _~~--------~--

en I I
» PARALLEL
DATA
B--4:~L~:-_4-----------_+-+_---------_4-----------~--
2 INPUTS C
C
»
en
o __~~__~________________~~~------------~--------------~-
L
Q I
I
:c I
o OUTPUTS
c
=i
en I--- SHIFT RIGHT ---.! I--- SHIFT LEFT -'1+--- INHIBIT ---l
CLEAR LOAD CLEAR
121
2-206 TEXAS
INSTRUMENTS
logic symbol
CLK
(15) QA
A
(14)
B QB
(13) QC
C
o 3,40 (12) QD
SL SER 171
....._---_....
2,40
PARALLEL INPUTS
A
'A B C 0'
MODE {Sl(10)
(3) ~) m) (6)
CONTROL
INPUTS ~~(~9)~~---+--~~-H----~~4+~-'~----+-~-H~+-----4-~~~1
SHIFT SHIFT
(7) LEFT
RIGHT ......:.;;(2;;.:.)____---.
SERIAL
r-+tt--f-"'-'- SER IAL en
INPUT INPUT !::
::)
u
a:
u
en
<t
111) C
CLOCK--~~~----------~----+_------~----~------~----_r------~
2:
CLEAR 1 <t
.
PARALLel OUTPUTS
(12)
Qo, en
...I
<t
Pin numbers shown are for J and N package.
TEXAS 2·207
INSTRUMENlS
4-BIT BIDIRECTIONAL UNIVERSAL SHIFT REGISTERS
In'put voltage .............................................................. 7 V
Operating free-air temperature range: SN54AS 194 ....................... - 55 °e to 125°e
SN74AS194 .......................... ooe to 150 0 e
Storage temperature range ............................ ,............. - 65 °e to 150 °e

SN54AS194 SN74AS194
UNIT
VIL Low·level input voltage 0.8 0.8 V
CLR
tw Pulse Duration
eLK
Set-up time Select
tsu
before CLKt Data
..
twr eLR
th Hold time, data after eLK t ns
TA Operating free-air temperaure -55 125 0 70 °e
electrical characteristics over recommended operating free-air temperature range

»
r-
(unless otherwise noted)
SN54AS194 SN74AS194
rn PARAMETER TEST CONDITIONS
UNIT
»
2
VIK
VOH
Vee = 4.5 V, II = -18 mA
Vee = 4.5 V to 5.5 V, IOH = -2 mA VCC- 2
-1.2
VCC-2
-1.2 V
V
c VOL Vee = 4.5 V, IOL = 20 mA 0.35 0.5 0.35 0.5 V
»
rn
II
IIH
Vee = 5.5 V,
Vee = 5.5 V,
VI = 7 V
VI = 2.7 V
mA
p.A
IlL Vee = 5.5 V, VI = 0.4 V mA
n 10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lJ I Outputs high
n lee Vee = 5.5 V
I Outputs low 27 27
mA
c t All typical values are at Vee = 5 V, T A = 25°e.

=i
rn :t:The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
1:
2-208 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012" • DALLAS. TEXAS 75265

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
FROM TOl R1 = 500 n. UNIT
PARAMETER
(INPUT) (OUTPUT) R2 = 500 n.
TA = MIN to MAX
SN54AS194 SN74AS194
f max MHz
tplH 5 5
CLK Any Q ns
tpHL 5.5 5.5
tpHL CLR Any Q 7.5 7.5 ns
t All typical values are at V CC =' 5 V. TA = 25°C.

..CJ)
!:::
::::>
u
a:
U
CJ)
«
c
2!
«
CJ)
-J
«
:3
TEXAS 2-209
INSTRUMENTS
- l>
r-
en
l>
2
C
l>
en
o
::J::J
o
C
~
en
2-210
4~BIT BIDIRECTIONAL UNIVERSAL SHIFT REGISTERS
• Parallel-to-Serial, Serial-to-Parallel SN54AS195 ... J PACKAGE

Conversions SN74AS195 ... N PACKAGE
(TOP VIEW)
• Parallel Synchronous Loading
ClR VCC
• J and K Inputs to First Stage
J OA
• Right-Shift Only with Complementary Outputs K Os
on Last Stage A Oc
S OD
• Direct Overriding Clear
C OD
• Dependable Texas Instruments Quality and D ClK
Reliability GND SHiill
description SN54AS195 ... FH PACKAGE

These 4-bit registers feature parallel inputs, SN74AS195 ... FN PACKAGE
parallel outputs, J-K serial inputs, shift/load (TOP VIEW)
Is u t5 od:
control input, and a direct overriding clear. The
registers have two modes of operation: ,uz>d
Parallel (broadside) load 3 2 1 2019
Shift (in the direction QA toward QD) K Os
A Oc
Parallel loading is accomplished by applying the
NC NC
four bits of data and taking the shift/load control
S OD
input low. The data are loaded into the
C OD
associated flip-flops and appear at the outputs
9 1011 1213
after the positive transition of the clock input ..
During loading serial data flow is inhibited.
Shifting is accomplished synchronously when tJ)
the shift/load control input is high. Serial data for NC - No internal connection t::
this mode is entered at the J-K inputs. These :::>
inputs permit the first stage to perform as a u
J-K, D-, or T-type flip-flop as shown in the a:
function table. u
The SN54AS 195 is characterized for operation tJ)
over the full military range of - 55 ac to 125 ac.
«
from 0 ac to 70 ac.
c
z
«
tJ)
-I
«

This page contain. Information on a product under
development. Texa. Instruments reserve. the right to TEXAS 2-211
change or discontinue this product without notice. INSTRUMENlS
logic symbol logic diagram (positive logic)

SERIAL INPUT PARALL~L INPUTS
~ I~A--------~----~~--~--------~O
(2) (3) (4) (5) (6) (7)
~--------------v~--------------~
PARALLEL OUTPUTS
FUNCTION TABLE
INPUTS OUTPUTS
SERIAL PARALLEL
CLEAR SHIFT/LOAD CLOCK °A OB Oc 00 QO
J K A B C 0
L X X X X X X X X L L L L L
H L t X X a b c d a b c d d
H H L X X X X X X OAO QBO QCO QOO DOO
H H t L H X X X X QAO QAO QS n QCn DCn
H H t L L X X X X L QAn QS n QCn DCn
H H t H H X X X X H QAn QS n QCn DCn
H H t H L X X X X OAn QAn QS n QCn DCn
typical clear, shift, and load sequences

CLOCK
I
I
SERIAL[ ~--~--~'T' I
INPUTSll K ~~____________________~:____~___________________
SHIFT/LOAD I L.l-.J
. PARALLEL{ : :
DATA C ~
~
INPUTS --~--------~--------------------~ I ~~-----------
r-
o LI
OUTPUTS{~: ~~~~
OC:::; :
00:::" I
I I I
I .....---SERIAL SHIFT------f t---SERIAL SHIFT-
CLEAR
12E
2-212 TEXAS
INSTRUMENTS
OCTAL BUFFERS AND LINE DRIVERS WITH 3·STATE OUTPUTS
• Included among the Package Options Are SN54AS230 •••• J PACKAGE SN54AS231 •••• J PACKAGE
20-Pin DIPs and Both Plastic and Ceramic SN74AS230 •••• N PACKAGE SN74AS231 •••• N PACKAGE
(TOP VIEW) (TOP VIEW)
Chip Carriers
1G vCC VCC
• ' AS230 Has True and Complementary Out- 1A1 2G 1A1 2G
puts 2Y4 1Y1 1Y1
• 'AS231 Has Complementary G and G Inputs 1A2 2A4 2A4

2Y3 1Y2 1Y2
• 3-State Outputs Drive Bus Lines or Buffer 1A3 2A3 2A3
Memory Address Registers 2Y2 1Y3 lY3
2A2 2A2
• High Capacitive Drive Capability
2Y1 1Y4 lY4
• Current Sinking Capability Up to 64 rnA GND 2A1 2A1

and Reliability
SN54AS230 .••• FH PACKAGE SN54AS231 •••• FH PACKAGE
description SN74AS230 •••• FN PACKAGE SN74AS231 •.•• FN PACKAGE
(TOP VIEW) (TOP VIEW)
These octal buffers and line drivers are designed
.q ~ U
specifically to improve the performance of three-state >-
N _< ICl
_ >U Cl
N
memory address drivers, clock drivers, and bus·
oriented receivers and transmitters. The designer. has a
..
choice of selected combinations of inverting and 1Yl 1Y1
non inverting outputs, symmetrical IT (active-low 2A4 2Y3 2A4
output control) inputs, and complementary G and G lY2 1A3 1Y2
inputs. 2A3 2Y2 2A3

1Y3 lA4 1Y3
The SN74AS230 and SN74AS231 can be used to
_ C _ -.:t ("Ii
drive terminated lines down to 133 ohms. - c _ ~ N
(/)
>- z < >- < >-z<>-<
The SN54AS230 and SN54AS231 are characterized
N (!) N - N N (!) N - N
!:::
:::>
u
of _55°e to 125°e. The SN74AS230 and SN74AS231
o a:
are characterized for operation from oOe to 70 e.
u
logic symbols (/)
'AS230 'AS231 <t
C
Z
<t
lY1 (/)
lY2 ..oJ
lY3 <t
1Y4
(9) 2Yl 2Yl

(7) 2Y2 2Y2
(5) 2Y3 2Y3
(3) 2Y4 2Y4
Pin numbers shown are for J and N packages_
TEXAS 2-213
INSTRUMENTS
OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
absolute maximum ratings over operating free-air temperature range

Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS230, SN54AS231 . . . . . . . . . . . . . . . . . . . . . . _. -55°C to 125°C
SN74AS230, SN74AS231 . . . . . . . . . . . . . . . . . . . . . . _ ... , oOe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . _65° e to 150°C
recommended operating condi~ions

SN54AS230 SN74AS230
MIN NOM MAX MIN NOM MAX \

SN54AS230 SN74AS230
SN54AS231 SN74AS231
-18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = -2 mA Vee- 2 vee- 2
Vee = 4.5 V, 10H = -3 mA 2.4 3.4 2.4 3.4
VOH V
Vee = 4.5 V, 10H = -12 mA 2.4
Vee = 4.5 V, 10H = -15 mA 2.4
Vee = 4.5 V, 10l = 48 mA 0:27 0.55
VOL V
Vee = 4.5 V 10l = 64 mA 0.31 0.55
10ZH~ Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
10Zl Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 p.A
'AS230 2A -1 -1
III Vee = 5.5 V, VI = 0.4 V mA
All others -0.5 -0.5
10:1: Vee = 5.5 V. Vo = 2.25 V -50 -150 -50 -150 mA
Outputs high 16 25 16 25
'AS230 Vee = 5.5 V Outputs low 55 87 55 87 mA
Outputs disabled 29 46 29 46 mA
lee
'AS231 Vee =5.5 V Outputs low 52 82 52 82 mA
Outputs disabled 25 39 25 39

121
2-214 TEXAS
INsrRUMENlS
OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
, AS230 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO Rl = 500 n.
PARAMETER UNIT
TA = MIN to MAX
SN54AS230 SN74AS230
MIN MAX MIN MAX
tpLH 2.5 7 2.5 6.5
1A 1Y ns
tpHL 2 6 2 5.7
tpLH 2.5 9 2.5 6.2
2A 2Y ns
tpHL 2 7 2 6.2
tpZH 2 7 2 6.4
tpZL 2 9 2 8.5
10 1Y ns
tpHZ 2 5.5 2 5
tpLZ 2 12.5 2 9.5
tpZH 2 10 2 9
tpZL
tpHZ
io 2Y
2
2
8
6.5
2
2
7.5
6
ns
tpLZ 2 10.5 I 2 9

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
FROM TO Rl = 500 n.
UNIT
TA = MIN to MAX
SN54AS231 SN74AS231
en
MIN MAX MIN MAX !::
tpLH 2 7 2 6.5 :J
A Y ns U
2 6 2 5.7
tpHL
tpZH 2 7 2 6.4
ex:
tpZL
G Y
2 9 2 8.5
ns
U
tpHZ 2 5.5 2 5 en
tpLZ
tpZH
2
3
12.5
7
2
3
9.5
6
<t
tpZL 3 10 3 9 c
tpHZ
G Y
3 6.5 3 6
ns 2
tpLZ 3 13.5 3 7 <t
en
..J
<t
:33
TEXAS 2-215
INSTRUMENTS
~
:t:-
r-
tf)
:t:-
2:
C
:t:-
tf)
o
::D
o
c
=i
tf)
2-216
02661, DECEMBER 19B2-REVISED DECEMBER 1983
• 3·State Outputs Drive Bus Lines or Buffer Memory SN54ALS', SN54AS' ... J PACKAGE
Address Registers SN74ALS', SN74AS' ... N PACKAGE
(TOP VIEW)
• P·N·P Inputs Reduce DC Loading
1<3 Vee
o Dependable Texas Instruments Quality and Reliability 1A1 2G/2G*
2Y4 1Y1
description 1A2 2A4
These octal buffers and line drivers are designed specifically to 2Y3 1Y2
improve both the performance and density of three-state memory 1A3 2A3
address drivers, clock drivers, and bus-oriented receivers and 2Y2 1Y3
transmitters, The designer has a choice of selected combinations 1A4 2A2
of inverting and noninverting outputs, symmetrical G (active-low 2Y1 1Y4
output control) inputs, and complementary G and Ginputs. These GND 2A1
devices feature high fan-out and improved fan-in.
SN54ALS·. SN54AS' . . . FH PACKAGE
The -1 versions of the SN74ALS' parts are identical to their SN74ALS'. SN74AS' ... FN PACKAGE
standard versions except that the recommended maximum IOL (TOP VIEW) *
is increased to 48 milliamperes. There are no -1 versions of the C!I
SN54ALS' parts. '<t.... u~
>- « IC!I ulC!l
N ........ >N
The SN54' family is characterized for operation over the full
3 2 1 2019
military temperature range of - 55°C to 125°C. The SN74' family
is characterized for operation from ooe to 70°C. 1Y1
5 2A4
logic symbols 1A3 6 1Y2
2Y2 7 2A3
'AlS240A. 'AS240 1A4 8 1Y3
9 10 111213
CJ)
1Yl
lY2
!:::
1Y3
:;:)
*2G for 'ALS240A, 'AS240 or 2G for 'ALS241A, 'AS241
1Y4
C,.)
logic diagrams (positive logic) a:
'ALS240A, 'AS240 'AlS241A, 'AS241 U
2Al 2Yl CJ)
2A2 iY2 cd:
2A3 2Y3 1181
1Yl 1181 1Yl
2A4 2Y4 C
1161 1161 lY2
2
lY2
cd:
'AlS241A, 'AS241
1141
1Y3 1141 1Y3 CJ)
10 ...J
118) 1121
1Y4 1121 1Y4 cd:
1Yl
(16)
lY2
(14) 211 1191
1Y3 2G
(12)
1Y4
191 191 2Yl
2Y1 2A1
2G
(9) 171 2Y2 (7)
2Al 2Yl 2Y2
2A2 m 2Y2
(5) 151 151
2A3 2Y3 2Y3 2Y3
(3)
2A4 2Y4
13) 2Y4 131
Pin numbers shown are for J and N packages. 2Y4

13
TEXAS 2-217
INSTRUMENTS
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS240A, SN54ALS231 A . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS240A, SN74ALS241A .. , ..•..... , ........ , ooe to 70°C

12 24
IOL Low-level output current rnA
48 t
tThe extended limits apply only if Vee is maintained between 4.75 V and 5.25 V.
The 48 mA limit applies for the SN74ALS240A·l and SN74ALS241A-l only.
MIN TYP~ MAX MIN TYp:l: MAX
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA Vee- 2 Vee- 2
Vee = 4.5 V, IOH = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, IOH= -12 rnA 2
Vee = 4.5 V, IOH = -15 rnA 2
Vee = 4.5 V, IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL Vee = 4.5 V, IOL = 24 rnA V
0.35 0.5
(lOL = 48 rnA for - 1 versions)
IOZH Vee = 5.5 V, Vo = 2.7V 20 20 p.A
IOZl Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
'AlS240A Outputs low 13 23 13 23
lec Outputs disabled 14 25 14 25
Vee = 5.5 V rnA
'ALS241A Outputs low 15 28 15 26
t All typical values are at Vee = 5 V, TA = 25°e.

128
2-218 TEXAS
INSTRUMENTS
OCTAL BUFFERS AND LlfJE DRIVERS WITH 3·STATE OUTPUTS
'ALS240A switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
R1 = 500 Q,
FROM TO
PARAMETER R2 = 500 Q, UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 12 2 9
A Y ns
tpHL 2 11 2 9
tpZH 5 15 5 13
G Y ns
tpZL 5 20 5 18
tpHZ 2 12 2 10
G Y ns
tpLZ 3 18 3 12
, ALS241 A switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
R1 = 500 Q,
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 3 14 3 11
A Y ns (J)
tpHL 3 13 3 10
tpZH
1(3
7 25 7 21 !:::
Y
7 25 7 21
ns ~
tpZL
tpHZ 2 12 2 10 u
tpLZ
1(3 Y
3 20 3 15
ns a:
tpZH
2G Y
7 25 7 21
ns
u
tpZL 7 25 7 21 (J)
tpHZ
tpLZ
2G Y
2
3
12
20
2
3
10
15
ns «
c
NOTE1: For load circuit and voltage waveforms, see page 1-12. z
«
(J)
-I
«
83
TEXAS 2-219
INSTRUMENTS
, POST OFFICE BOX 225012 • DALLAS, TEXAS 75265
Supply voltage, Vee ............................................ :................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Voltage applied to a disabled 3-state output ............................................. 5.5 V
Operating free-air temperature range: SN54AS240, SN54AS241 .................... - 55°C to 125°C
SN74AS240, SN74AS241 ...•... :................ ooe to 70°C
Storage temperature range ........... _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C

SN54AS240 SN74AS240
Vll low-level input voltage 0.8 0.8 V
SN54AS240 SN74AS240
~ PARAMETER TEST CONDITIONS

SN54AS241
MIN Typt MAX
SN74AS241
MIN TYpt MAX
UNIT
»
r-
VIK Vee
Vee.
= 4.5 V,
= 4.5 V to
II
5.5 V, IOH
= -18 rnA
= -2 rnA vee- 2
-1.2
Vee- 2
-1.2 V
en VOH
Vee = 4.5 V, IOH = -3 rnA 2.4 3.4 2.4 3.4
V
»
:2
Vee
Vee
= 4.5 V,
= 4.5 V,
IOH = -12 rnA
IOH = -15 rnA
2.4
2.4
C Vee = 4.5 V, IOl = 48 rnA 0.27 0.55

V
VOL
Vee = 4.5 V, IOl = 64 rnA 0.31 0.55
»
en IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
IOZl Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
Q II Vee = 5.5 V, VI =7V 0.1 0.1 rnA
:xJ IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
o III
'AS241 A inputs
Vee = 5.5 V, VI = 0.4 V
-1 -1
rnA
c All others
= 5.5
-0.5 -0.5
=i IOi Vee V, Vo = 2.25 V -50 -150 -50 -150 rnA
en 'AS240
Outputs high
Outputs low
11
51
17
75
11
51
17
75
lee Outputs disabled 24 38 24 38
Vee = 5.5 V
rnA
'AS241 Outputs low 61 90 61 90


121
2-220 TEXAS
INSTRUMENTS
OCTAL BUFFERS AND LlLNE DRIVERS WITH 3·STATE OUTPUTS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
PARAMETER
FROM TO R1 = 500 D.
UNIT
(INPUT) (OUTPUT) R2 = 500 D.
TA = MIN to MAX
SN54AS240 SN74AS240
MIN MAX MIN MAX
tpLH 2 7 2 6.5
A Y ns
tPHL 2 6 2 5.7
tpZH y 2 7 2 6.4
G ns
tpZL 2 9.5 2 9
tpHZ y 2 5.5 2 5
13 ns
tpLZ 2 12.5 2 9.5
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
PARAMETER
FROM TO R1 = 500 D.
UNIT
(INPUT) (OUTPUT) R2 = 500 D.
TA = MIN to MAX
SN54AS241 SN74AS241
MIN MAX MIN MAX
tpLH 2 9 2 6.2
A Y ns
tpHL 2 7
10
2 6.2
9
en
tpZH
tpZL
113 y 2
2 8
2
2 7.5
ns !:::
:::;)
tPHZ y 2 6.5 2 6 ()
"(3" ns
tPLZ
tpZH
2
3
10.5
11
2
3
9
10.5
a:
2G y ns ()
tpZL 3 9.5 3 8.5
tpHZ
2G Y
3 7 3 7 en
tpLZ 3 12 3 12
ns
<t
NOTE 1: For load circuit and voltage waveforms, see page 1-12. c
2
<t
en
. ...J
«
!3
TEXAS 2-221
INSTRUMENTS
2-222
QUADRUPLE BUS TRANSCEIVERS WITH 3·STATE OUTPUTS
• 2-Way Asynchronous Communication Between Data SN54' . . . J PACKAGE

Buses SN74' . . . N PACKAGE
(TOP VIEW)
• P-N-P Inputs Reduce Loading
• Dependable Texas Instruments Quality and Reliability GAB VCC
NC GBA
A1 NC
description A2 B1
These four-data-line transceivers are designed for asynchronous A3 B2
two-way communications between data buses. The SN74ALS' A4 B3
devices can be used to drive terminated lines down to 133 ohms. GND B4
The -1 versions of the SN74ALS' parts are identical to the

standard versions except that the recommended maximum IOL is
increased to 48 milliamperes. There are' no -1 versions of the SN54' . . . FH PACKAGE
SN54ALS' parts. SN74' . . . FN PACKAGE
(TOP VIEW)
The SN54' family is characterized for operation over the full
military temperature range of -,55°C to 125°C. The SN74' al u~
U~UUal
family is characterized for operation from ooC to 70°C. ZI(!) Z > (!)
logic symbol
A1 NC
'ALS242A, 'AS242 'ALS243A, 'AS243 NC NC
A2 B1
NC NC
B2
B1
o:tOUo:tM
B2
~ Z' Z al al
(!)
en
!::
B3 NC-No Internal connection ::>
(.)
B4 a:
U
en
«
FUNCTION TABLE
c
INPUTS 'ALS242A 'ALS243A z
'ALS242A, 'AS242
GAB GBA 'AS242 'AS243 «
'ALS243A, 'AS243 L L A to B A to B en
H H 6to A B to A ...J
H L Isolation
Latch A and B
Isolation
Latch A and B
«
L H
(A=6) (A=B)

83
TEXAS 2-223
INSTRUMENTS
Input voltage: All inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
I/O ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS242A, SN54ALS243A ............... ,. -55°e to 125°e
SN74ALS242A, SN74ALS243A ................... " ooe to 70 0 e
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e
12 24
10L Low-level output current rnA
48 t
The 48-mA limit applies for the SN74ALS242A-1 and SN74ALS243A-1 only.
MIN Typi MAX MIN Typi MAX
Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
l> VIK
r- Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA Vee- 2 Vee- 2
en VOH
Vee = 4.5 V 10H = -3 rnA 2.4 3.2 2.4 3.2
V
Vee = 4.5 V, 10H = -12 rnA 2
l> Vee = 4.5 V, 10H = -15 rnA 2
2 0.25 0.4 0.25
Vee = 4.5 V, 10L = 12 rnA 0.4
C
VOL Vee = 4.5 V, IOL = 24 rnA
0.35 0.5 V
l> (lOL = 48 rnA for-l versions)
en Control inputs Vee = 5.5 V, VI = 7 V 0.1 0.1
rnA
n II
A or B ports
Control inputs
Vec = 5.5 V, VI = 5.5 V 0.1
20
0.1
20
l:J IIH Vee = 5.5 V, VI = 2.7 V p.A
n A or B ports§
Control inputs
20
-0.1
20
-0.1
C IlL Vce = 5.5 V, VI = 0.4 V rnA
~
A or B ports§ -0.1 -0.1
en 10' Vce = 5.5 V, Vo = 2.25 V

Outputs high
-30
10
-112
20
-30
10
-112
16
rnA

ICC Vec = 5.5 V rnA
tAli typical values are at Vee = 5 v, TA = 25°e. ,

§For liD ports, the parameters IIH and IlL include the off-state output current.
'The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
12
2-224 TEXAS
INSTRUMENlS
•ALS242A switching characteristics (see Note 1)
Vee = 4.5 V to 5.5 V.

eL = 50 pF.
FROM TO R, = 500 Q.
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 Q.
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 3 15 3 11
A or B B or A ns
tpHL 2 14 2 10
tpZH 4 22 4 18
GAB B ns
. tpZL 7 25 7 21
tpHZ 2 16 2 14
GAB B ns
tpLZ 4 28 4 22
tpZH 4 22 4 18
GBA A ns
tpZL 7 25 7 21
tpHZ 2 16 2 14
GBA A ns
tpLZ 4 28 4 22
•ALS243 switching characteristics (see Note 1)

Vec = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 Q.
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 Q.
TA = MIN to MAX en
MIN MAX MIN MAX
!::
tpLH 4 15 4 11
::J
tpHL
A or B B or A
4 15 4 11
ns U
CC
tpZH 7 25 7 20
tpZL
GAB B
7 25 7 20
ns U
tpHZ 2 16 2 14 en
tPLZ
GAB B
3 27 3 22
ns
«
tpZH
GBA A
7 25 7 20
ns c
tpZL 7 25 7 20
z
tpHZ
tpLZ
GBA A
2
3
16
27 3
2 14
22
ns «
en
NOTE 1: For load circuit and voltage waveforms, see page 1-12. -1
«
83
TEXAS 2-225
INSTRUMENTS
QUADRUPLE BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS242, SN54AS243 . . . . . . . . . . . . . . . . . . " - 55 °e to 125 °e
SN74AS242,SN74AS243 . . . . . . . . . . . . . . . . . . . . . . . . 00et070 0e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e

SN54AS242 SN74AS242
IOH High·level output current -12 -15 mA
SN54AS242 SN74AS242
SN54AS243 SN74AS243
-18 mA -1.2 -1.2 V
-.J VOH
Vcc - 4.5 V to 5.5 V,
Vcc = 4.5 V
IOH = -2 mA
IOH = -3 mA
Vee- 2
2.4 3.4
Vee- 2
2.4 3.4
V
l> VCC = 4.5 V, IOH = -12 mA 2.4
r Vee = 4.5V, IOH = -15 mA 2.4
en VOL
VCC = 4.5 V, IOL = 48 mA 0.55
V
l> VCC = 4.5 V, IOL = 64 mA 0.55
2 Control inputs VCC = 5.5 V, VI = 7 V 0.1 0.1

mA
II
C A or B ports VCC = 5.5 V, VI = 5.5 V 0.1 0.1
Control inputs 20 20
l> IIH
A or B ports;
VCC = 5.5 V, VI = 2.7 V
50 50
p.A
en Control inputs -0.5 -0.5
C') 'AS242
-0.5 -0.5
:II IlL A or B ports; VCC = 5.5 V, VI = 0.4 V mA
C') 'AS243
-1 -1
c A or B ports;
=i IO§ Vce- 5.5 V, Vo = 2.25 V -50 -150 -50 -150 mA

en 'AS242
Outputs high
Outputs low
18
38
28
60
18
38
28
60
ICC VCC = 5.5 V
mA
'AS243 Outputs low 47 74 47 74

t All typical values are at Vee = 5 V, TA = 25°C.

~For I/O ports, the parameters IIH and IlL include the off-state output current. .
§The output conditions have been chosen to produce a current that closely' approximates one half of the true short-circuit output current, lOS'
12
2-226 TEXAS
INSTRUMENTS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
PARAMETER
FROM TO R1 = 500 n.
UNIT
TA = MIN to MAX
SN54AS242 SN74AS242
MIN MAX MIN MAX
tpLH 2 7 2 6.5
A or B B or A ns
tpHL 2 6 2 5.7
tpZH 2 9 2 5.S
GAB B ns
tpZL 2 8.5 2 7.5
tpHZ 2 7 2 6.S
GAB B ns
tpLZ 2 12.5 2 9.S
tpZH 3 7 3 6
GAB A ns
tpZL 3 9 3 8
tpHZ 3 8.5 3 6
GAB A ns
tpLZ 3 13.5 3 10.5

Vcc = 4.5 V to 5.S V.
CL = SO pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
SN54AS243 SN74AS243
tPLH
MIN
3
MAX
9
MIN
3
MAX
7.5
en
tpHL
A or 8 B or A
3 8 3 6.5
ns !::
:>
tpZH
GAB B
2 10 2 9
ns u
tpZL
tpHZ
2
2
9
7
2
2
7.S
6.5
a:
tpLZ
GAB B
2 11 2 9
ns C3
tpZH 3 11 3 10.5 en
tpZL
GAB A
3 9.5 3 8.5
ns
«
tpHZ
GAB A
3 7.5 3 7
ns c
tpLZ 3 14 3 11
z
NOTE 1: For load circuit and voltage waveforms. see page 1-12 .. «
en
-J
«
283
TEXAS 2-227
INSTRUMENTS
- l>
r-
tn
l>
2:
C
l>
tn
Q
:D
(')
C
~
tn
2-228
D2661. DECEMBER 1982-REVISED DECEMBER 1983
• 3-State Outputs Drive Bus Lines or Buffer Memory SN54ALS244A. SN54AS244 ... J PACKAGE
Address Registers SN74ALS244A. SN74AS244 ... N PACKAGE
(TOP VIEW)
• P-N-P Inputs Reduce DC Loading

1G Vee
1A1 2G
2Y4 1Y1
• Dependable Texas Instruments Quality and Reliability 1A2 2A4
2Y3 1Y2
1A3 2A3
description
2Y2 1Y3
These octal buffers and line drivers are designed specifically to 1A4 2A2
improve both the performance and density of three-state memory 2Y1 1Y4
address drivers. clock drivers, and bus-oriented receivers and GND 2A1
transmitters. Taken together with the' ALS240A, 'ALS241 A.
'AS240, and' AS241, these devices provide the choice of selected
combinations of inverting outputs, symmetrical G (active-low input SN54ALS244A. SN54AS244 ... FH PACKAGE
control) inputs, and complementary G and G inputs. SN74ALS244A. SN74AS244 ... FN PACKAGE
The -1 version of the SN74ALS244A is identical to the standard (TOP VIEW)
version except that the recommended maximum IOL is increased
to 48 milliamperes. There is no -1 version of the SN 54ALS244A.
3 2 1 20 19
The SN54ALS244A and SN54AS244 are characterized for
operation over the full military temperature range of - 55°C to 1A2 4 1Y1
125°C. The SN74ALS244A and SN74AS244 are characterized 2Y3 5 2A4
for operation from ooe to 70°C. 1A3 6 1Y2
2Y2 7 2A3
1A4 8 1Y3
logic diagram (positive logic) 9 10 111213 en
"'-O.-<;tN
>-z<t:>-<t: t::
lG
N(!jN"'-N :J
U
lAl
(2\ (18\
lVl
a:
logic symbol
U
lA2
(4\ (16\
1V2
113
en
<C
(6\ (14\ lAl (18\ WI
lA3 1V3
lA2
(161
W2
C
lA3
(141
W3
2
lA4
(8\ (12\
1V4 lA4
(121
W4 <C
en
213 ..J
2Al \l
(91
2Vl
<C
(131 (7)
2A2 2V2
(151 (51
(9\ 2A3 2V3
2Al 2Vl (171 (3) 2V4
2A4
(7\
2A2 2V2
(5\
2A3 2V3
(3\
2A4 2V4

83
TEXAS 2-229
INSTRUMENlS
TYPES SN54ALS244A, SN74ALS244A,
Supply voltage, Vee .......................... : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS244A. . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS244A ................................. ooe to 70°C

UNIT
12 24
IOL Low-level output current mA
48 t
The 48-mA limit applies for the SN74ALS244A-1 only.
-.J electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
MIN TYP~ MAX MIN TYP~ MAX
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V. IOH = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4_5 V. IOH = -12 mA 2
Vee = 4.5 V, IOH = -15 mA 2
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL Vee = 4.5 V IOL = 24 mA V
0.35 0.5
(lOL = 48 mA for - 1 version)
IOZH Vee = 5.5 V, Vo = 2.7V 20 20 p.A
IOZL Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
l Outputs high 9 15 9 15
ICC Vee = 5.5 V I Outputs low 15 24 15 24 mA
I Outputs disabled 17 27 17 27
§Theoutput conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
128
2-230 TEXAS
INSTRUMENTS
switching characteristics (see Note 11

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
PARAMETER R2 = 500 n. UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 3 13 3 10
A Y ns
tpHL 3 13 3 10
tpZH 7 25 7 20
G Y ns
tpZL 7 25 7 20
tpHZ 2 12 2 10
G Y . 18
ns
tpLZ 3 3 13
en
!::
::>
u
a:
U
en
«
c
z
«
en
..J
«
283
TEXAS 2-231
INSTRUMENTS
OCTAL BUFFERS AND LINE DRIVERS WITH 3·STATEOUTPUTS
\
Supply voltage, Vee . . . . . . . . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS244 . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. - 55 °e to 125 °e
SN74AS244 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range ....... ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 1 50 °e

SN54AS244 SN74AS244
UNIT
~ PARAMETER TEST CONDITIONS

MIN
SN54AS244
Typt MAX MIN
SN74AS244
TYpt MAX
-1.2
UNIT
V,K Vee = 4.5 V, " = -18 rnA -1.2 V

~ Vee = 4.5 V to 5.5 V. IOH = -2 rnA
r- Vee- 2 Vee- 2
en VOH
Vee =-4.5 V. IOH = -3 rnA 2.4 3.4 2.4 3.4
V
Vee = 4.5 V. IOH = -12 rnA 2.4
~ Vee = 4.5 V, IOH = -15mA 2.4
:2 Vee = 4.5 V. 10l = 48 rnA 0.55
C VOL
Vee = 4.5 V IOl = 64 rnA 0.55
V
~ IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A

en IOZl Vee => 5.5 V. Vo = 0.4 V -50 -50 p.A
(") Vee = 5.5 V. V, = 7 V 0.1 0.1 rnA
"
"H Vee = 5.5 V. V, = 2.7 V 20 20 p.A
:xJ
(")
"l I G
Vee = 5.5 V. V, = 0.4 V
-0.5 -0.5
rnA
C I A -1 -1
~ loi Vee = 5.5 V. Vo = 2.25 V -50 -150 -50 -150 rnA

en I Outputs high 22 34 22 34
lee Vee = 5.5 V I Outputs low 60 90 60 90 rnA

*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
12E
2-232 TEXAS .
INSTRUMENTS
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
R1 = 500 n,
FROM TO
PARAMETER R2 = 500 n, UNIT
(INPUT) (OUTPUT)
TA '= MIN to MAX
SN54AS244 SN74AS244
MIN MAX MIN MAX
tpLH 2 9 2 6.2
A Y ns
tpHL 2 7 2 6.2
, tpZH y 2 10 2 9
G ns
tpZL 2 8 2 7.5
tpHZ y 2 6.5 2 6
IT ns
tpLZ 2 10.5 2 9
..en
!::
=>
u
a:
u
en
<t
C
Z
<t
en
...J
<t
283
TEXAS 2-233
INSTRUMENTS
~
l>
r-
en
l>
2:
o
l>
en
o
$
o
c
::;
en
2-234
OCTAL BUS TRANSCEIVERS WITH 3·STATE OUTPUTS
• 3-State Outputs Drive Bus Lines Directly SN54ALS245A. SN54AS245 ••. J PACKAGE
SN74ALS245A. SN74AS245 •.. N PACKAGE
• P-N-P Inputs Reduce Dc Loading (TOP VIEW)
• •AS Version in Development. Data Will Be Provided As
DIR VCC
It Becomes Available. Contact the Factory for Latest
A1 G
Information
A2 81
• Package Options Include Both Plastic and Ceramic A3 82
Chip Carriers in Addition to Plastic and Ceramic DIPs A4 83
A5 84
• Dependable Texas Instruments Quality and Reliability A6 85
A7 86
description
A8 87
These octal bus transceivers are designed for synchronous two- GND 88
way communication between data buses The control function
implementation minimizes external timing requirements.
SN54ALS245A. SN54AS245 .•. FH PACKAGE
The devices allow data transmission from the A bus to the 8 bus SN74ALS245A. SN74AS245 •.• FN PACKAGE
or from the 8 bus to the A bus depending upon the logic level at (TOP VIEW)
the direction control (DIR) input. The enable input (0) can be used
to disable the device so that the buses are effectively isolated.
The -1 version of the SN74ALS245A is identical to the standard

version except that the recommended maximum IOL is increased 81
to 48 milliamperes. There is no - 1 version of the SN54ALS245A. 82
83
The SN54ALS245A and SN54AS245 are characterized for
84
85
125°C. The SN74ALS245A and SN74AS245 are characterized
for operation from O°C to 70°C.
en
!::
::::>
FUNCTION TABLE
ua:
ENABLE
DIRECTION
OPERATION c.J
G
CONTROL
en
L
DIR
L B data to A bus
<t
L H A data to B bus C
H X Isolation 2
<t
en
...J
<t
TEXAS 2-235
INSTRUMENTS
DIR logic symbol

(19) G
A1 .....---.~ ~+-~ ..........~
1-....- - B 1
A2 .....---.~ ~+-~ ..........~
1-....-.:..:.~B2 A1 B1
A2 B2
A3 B3
A4 B4
AS BS
A6 B6
A7 B7
AS' BS
1-......:.....~B6
A7----.~ ~+-~----~
A8----+~
-
~---~c ~~~~-B8
»
r-
Input voltage: All inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
rn liD ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
»
2
Operating free-air temperature range: SN54ALS245A.. . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55 °C to 125°C
SN74ALS245A ................................. ooe to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 DC
o
»
rn
UNIT
Q MIN NOM MAX MIN NOM MAX
:D Vee Supply voltage 4.S 5 5.5 4.5 5 5.5 V
o V,H High-level input voltage 2 2 V
C V,L Low-level input voltage 0.8 0.8 V
~ IOH High-level output current -12 -15 mA
en IOL Low-level output current
12 24
mA
48 t
The 48·mA limit applies for the SN74ALS245A·1 only.
128
2-236 TEXAS
INSTRUMENTS
OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
VIK Vce = 4.5 V. II = -18 rnA -1.5 -1.5 V
Vce = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2
Vce = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2
V
VOH
Vce = 4.5 V. IOH = -12 rnA 2
Vce = 4.5 V. IOH = -15 rnA 2
Vce = 4.5 V. IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL Vce = 4.5 V. IOL = 24 rnA V
0.35 0.5
(lOL = 48 rnA for - 1 versions)
Control inputs Vce = 5.5 V. VI = 7 V 0.1 0.1
II rnA
A or B ports Vce = 5.5 V. VI = 5.5 V 0.1 0.1
IIH Vce = 5.5 V. VI = 2.7 V p.A
A or B ports; 20 20
Control inputs -0.1 -0.1
IlL Vce = 5.5 V. VI = 0.4 V
-0.1 -0.1
rnA
A or B ports;
IO§ Vce = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
I Outputs high 30 48 30 45
ICC VCC = 5.5 V I Outputs low 36 60 36 55 rnA
tAli typical values are at Vee =5 V. TA = 25°G..

tFor 110 ports. the parameters IIH and IlL include the off·state output current.
§The output conditions have been chosen to produce a current that close'ly approximates one half of the true short·circuit output current. lOS'

Vcc = 4.5 V to 5.5 V.
en
CL = 50 pF.
R1 = 500 n. !=
FROM TO R2 = 500 n.
:::>
PARAMETER UNIT ()
a:
MIN MAX MIN MAX u
tpLH 3 15 3 10 en
tpHL
A or B B or A
3 13 3 10
ns
«
tpZH
IT A or B
5 25 5 20
ns c
tpZL 5 25 5 20
z
tpHZ
tpLZ
IT A or B
2
4
12
18
2
4
10
15
ns «
en
..J
«
!83
TEXAS 2-237
INSTRUMENTS
OCTAL BUS TRANSCEIVERS WITH 3·STATEE OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
I/O ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54AS245. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74AS245 ................................... ooe to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 6'5°e to 1 50°C

SN54AS245 SN74AS245
UNIT
V,L Low·level input voltage 0.8 0.8 V
SN54AS245 SN74AS245
V,K Vee = 4.5 V, " = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 mA vee- 2 Vee- 2
Vee = 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, IOH = -12 mA 2.4
Vee = 4.5 V, IOH = -15 mA 2.4
Vee = 4.5 V, IOL = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, IOL = 48 mA 0.35 0.5
Control inputs Vee = 5.5 V, V, = 7 V 0.1 0.1
mA
A or B ports Vee = 5.5 V, V, = 5.5 V 0.1 0.1
"
eontrol inputs 20 20
I'H Vee = 5.5 V, V, = 2.7 V
50
/LA
A or B ports; 50
I,L Vee = 5.5 V, V, = 0.4 V
-0.75
mA
A or B ports; -0.75
lo§ Vee = 5.5 V, Vo = 2.25 V -30 - -112 -30 -112 mA
I Outputs high 62 62
Ice Vee = 5.5 V I Outputs low 95 95 mA
I Outputs disabled 79 79
t All typical values are ~t Vee = 5 V, T A = 25°e.

*For 1/0 ports, the parameters IIH and IlL include the off-state output current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
PRODUCT PREVIEW 12
2 -2 38
development. Texas Instruments re.. rvellM rlghl to TEXAS
change or discontinue this product without nollce.
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO R2 = 500 n.
PARAMETER UNIT
SN54AS245 SN74AS245
tpLH 6 6
A or B B or A ns
tpHL 5 5
tpZH 8 8
G A or B ns
tpZL 8 8
tpHZ 4.5 4.5
IT AcrB ns
tpLZ 5 5

en
!::
::J
U
a:
U
en
<t
c
z
<t
en
..J
<t
83 PRODUCT PREVIEW
Thia page contains InlonnatJon on a product under
development. Texa.lnstruments re ..rves the rtghtto TEXAS 2-239
INSTRUMENTS
- »
r-
en
»
z
c
»
en
(")
ij
(")
c:
=i
rn
2-240
1·0F·16 DATA GENERATORS/MULTIPLEXERS
WITH 3·STATE OUTPUTS
DECEMBER 1983
o 4·Line to 1-Line Multiplexer that can Select 1 SN54AS250 ... J DUAL-IN-LiNE PACKAGE
of 16 Data Inputs SN74AS250 ... N DUAL-IN-LiNE PACKAGE
(TOP VIEW)
o Applications:
Boolean Function Generator E7 VCC
Parallel·to·Serial Converter E6 E8
Data Source Selector E5 E9
El0
o Buffered 3·State Bus Driver Inputs Permit
Ell
Multiplexing from N Lines to One Line
E2 E12
o Dependable Texas Instruments Quality and El E13
Reliability E14
E15
description A
B
The' AS250 provides full binary decoding to select one
of sixteen data sources with an inverting W output. GND'-i.,;.';;""-':":..I-'C
The selected sources are buffered with symmetrical
propagation delay times. This reduces the possibility
SN54AS250 ... FH CHIP CARRIER PACKAGE
of transients occurring at the output.
SN74AS250 ... FN CHIP CARRIER PACKAGE
A buffered enable output (<3) may be used for n-line- (TOP VIEW)
to-one-line cascading. Taking the G high will place the U
output in a high-impedance state. In the high- LD<OI"'-UUOOC'l
wwwz>ww
impedance state, the output neither loads nor drives
the bus lines significantly. 432 1
E4 E10
The enable (G) does not affect the internal operations E3 Ell
of the data selector/multiplexer. New data can be set E2 E12
up while the outputs are disabled. NC NC en
The SN54AS250 is characterized for operation over E1
EO
E13
E14
!::
the full military temperature range of - 55 DC to :::::>
125 DC. The SN74AS250 is characterized for opera- G
12 131415161718
E15 ua:
tion from 0 DC to 70 DC.
I~ 0 ~ ~ U II) <i U
<.9
en
c
z
«
en
-I
«

33 PRODUCT PREVIEW
this document contains information on B product under
MUX
G EN
(15)
A
B
C
0
EO
(14)
(13)
(111
(8)
"}
3
0
G ,.,
(7)
El.
(6)
E2 2
(5)
E3 3
(4)
E4 4
(3)
E5 5
(2)
E6 6
(1)
E7
(23)
E8 8
(22)
E9 9
(21)
El0 10
(20)
-
E11 11
(19)
E12 12
(18)
E13 13
(17)
E14 14
(16)
l> E15 15
r-
0. Pin numbers shown are for J or N packages.
A
l>
2
C B
B G
l>
o DATA
SELECTS
B
Q C
C
:xJ C
(')
c 0
0
=i
o 0
12
2·242 TEXAS
INsrRuMENTS
FUNCTION TABLE
INPUT OUTPUT
G A B C D Ei W
L L L L L EO EO
L H L L L El El
L L H L L E2 E2
L H H L L E3 E3
L L L H L E4 E4
L H L H L E5 E5
L L H H L E6 E6
L H H H L E7 E7
L L L L H E8 E8
L H L L H E9 E9
L L H L H EIO EIO
L H H L H Ell Ell
L L L H H E12 E12
L H L H H E13 E13
L L H H H E14 E14
L H H H H E15 E15
H X .X X X X Z
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54AS250... . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74AS250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOC to 70°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150 °e

SN54AS250 SN74AS250
UNIT
MIN NOM MAX MIN NOM .MAX
IOH High-level output curr -12 -15 mA
IOL Low-level output cun 32 48 mA
TA Operating free-air tel Irature -55 125 0 70 °e
l3
TEXAS 2-243
INSTRUMENTS
SN54AS250 SN74AS250
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. IOH = -2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V. IOH = -12 rnA 2.4 3.2 V
Vee = 4.5 V. IOH = -15 rnA 2.4 3.3
Vee = 4.5 V. IOL = 32 rnA 0.25 0.5
VOL V
Vee = 4.5 V. IOl = 48 rnA 0.35, 0.5
IOZH Vee = 5.5 V. Vo = 2.7 V 50 50 p.A
IOZl Vee = 5.5 V. Vo = 0.4 V -50 -50' p.A
II Vee = 5.5 V. VI = 7 V rnA
IIH Vee = 5.5 V. VI = 2.7 V p.A
III Vee = 5.5 V. VI = 0.4 V rnA
lot Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
I Outputs high
ICC Vee = 5.5 V I Outputs low rnA
J Outputs disabled
switching char~cteristics(see Note 1)
116 Vcc
Cl
R1
= 4.5 V to 5.5
= 50 pF.
= 500 O.
V.
l> PARAMETER
FROM TO
R2 = 500 O. UNIT
r- (INPUT) (OUTPUT)
. TA = MIN to MAX
tA
SN54AS250 SN74AS250
l> MIN TVPt MAX MIN TVPt MAX
:2 tPlH 4.3 4.3
C DATA Vi ns
tPHl 4.7 4.7
l> tplH
SELECT W
4.6 4.6
ns
tA tPHl 7.7 7.7
tpZH 4 4
C') G W ns
tpZl 4.9 4.9
ij tpHZ 3.1 3.1
C') IT Vi ns
tPLZ 3.9 3.9
c:
==i tAli typical values are at Vee = 5 V. TA = 25°e.
tA NOTE 1: For load circuit and voltage waveforms, see page 1-12.
2-244 TEXAS
INSTRUMENTS
1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3·STATE OUTPUTS
• Three·State Versions of 'ALS151 and 'AS151 SN54ALS251, SN54AS251. J PACKAGE

SN74ALS251, SN74AS251. N PACKAGE
• Three-State Outputs Interface Directly with System (TOP VIEW)
Bus
• Performs Parallel·to-Serial Conversion 03 VCC
02 04
• Complementary Outputs Provide True and Inverted 01 05
Data 00 06
• Fully Compatible with Most TTL Circuits Y 07
W A
• Package Options Include Both Plastic and Ceramic G B
Chip Carriers in Addition to Plastic and Ceramic DIPs GNO C
description
SN54ALS251, SN54AS251. . FH PACKAGE
These data selectors/multiplexers contain full binary decoding to SN74ALS251, SN74AS251. • FN PACKAGE
select one-of-eight data sources and feature strobe-controlled (TOP VIEW)
complementary three-state outputs.
C"') U
C'I u"<t
u
The three-state outputs can interface with and drive data lines of ooz>o
bus-organized systems. With all but one of the common outputs
disabled (at a high-impedance state), the low-impedance of the
01 05
single enabled output will drive the bus line to a high or low logic
00 06
level. Both outputs are controlled by the strobe (G). The outputs
NC NC
are disabled when G is high.
Y 07
The SN54ALS251 and SN54AS251 are characterized for W A
125°C. The SN74ALS251 and SN74AS251 are characterized Il!l 0 U U co CJ)
ZZ
l!l !::
NC - No internal connection.
:::>
()
a:
()
FUNCTION TABLE
INPUTS OUTPUTS logic symbol CJ)
SELECT STROBE
y w «
C B A G
G
MUX
c
X X X H Z Z
z
L
L
L
L
L
H
L
L
DO
01
Do
i51
A
B
:)G~ «
L H L L 02 D2 c- CJ)
...J
L
H
H
L
H
L
L
L
03
04
53
54
OO
01
02
0
\l
(5)
(6)
Y
W
«
\l
H L H L 05 Os 03
H H L L 06 Os 04 4
H H H L 07 07 05 5
06 6
DO, 01 •.. 07 ~ the level of the respective 0 input 07

33
TEXAS 2-245
INSTRUMENTS
1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
om
(4)
00
01 (3)
D2 (2)
D3 (1)
(5)
I----Y
DATA
INPUTS D4 (15) o-...:..(6....;..)_W
D5 (14)
- :t>
r-
en
:t>
2 DATA
D6 (13)
D7 (12)
SELECT B
C (BINARY) C
:t> {
en
o
:IJ
o
c
=i
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS251, SN54AS251 . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS251,SN74AS251 . . . . . . . . . . . . . . . . . . . . . . . . 00Cto700C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C
128
2-246 TEXAS
INSTRUMENTS
1 OFO DATA SELECTORS/MULTIPLEXERS WITH 3·STATE OUTPUTS

MIN NOM MAX MIN NOM. MAX
VIH Hi!1h-level input volta!1e 2 2 V
IOH High-level output current -1 -2.6 rnA
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA vee- 2 vee- 2
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V, 10L = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 24 rnA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 20 20. /lA
IOZL Vee = 5.5 V, VI = O.4-V -20 -20 /lA
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 /lA
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
IOi Vee =
5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
I Enabled Vee = 5.5 V, Inputs at Gnd. 7 10 7 10
lee I Disabled =
rnA
Vee 5.5 V, Inputs at 4.5 V 9.4 14 9.4 14
en
t All typical values are at Vee = 5 V, TA = 25 De.
t:
:::>
ua:
U
en
«
c
z
«
en
...J
«
13
TEXAS 2-247
INSTRUMENTS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tPLH 5 21 5 18
A. B or C Y ns
tpHL 8 28 8 24
tpLH 8 28 8 24
A. B or C W ns
tpHL 7 26 7 23
tpLH 2 12 2 10
Any D Y ns
tpHL 3 18 3 15
tpLH 3 18 3 15
Any D W ns
tpHL 3 18 3 15
tpZH 3 18 3 15
G Y ns
tpZL 3 18 3 15
tpZH 3 18 3 15
G W ns
tpZL 3 18 3 15
tpHZ 2 12 2 10
G Y ns
tpLZ 1 12 1 10
tpHZ 2 12 2 10
G W ns
tpLZ 1 12 1 10
-.J
»
r-
en
»
:2
C
»
en
o
:xl
o
c
=i
en
12E
2-248 TEXAS
INSTRUMENTS
1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS

SN54AS251 SN74AS251
UNIT
SN54AS251 SN74AS251
VIK Vee = 4.5 V. II = -18 rnA , -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. 10H = -2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V. 10H = -12 rnA 2.4 3.2 V
Vee = 4.5 V. 10H = -15 rnA 2.4 3.3
Vee = 4.5 V. 10l = 32 rnA 0.25 0.5
V
VOL
Vee = 4.5 V. 10l = 48 rnA 0.35 0.5
10ZH Vee = 5.5 V. Vo = 2.7V 50 50 /LA
10Zl Vee = 5.5 V. VI = 0.4 V -50 -50 /LA
A. B.C 0.2 0.2
All other 0.1 0.1
A. B.e 40 40
IIH Vee = 5.5 V. VI = 2.7 V /LA
All other 20 20
A. B.e -0.6 -0.6
III Vee = 5.5 V. VI = O.4V rnA
All other -0.3 -0.3 CJ)
lOt = Vo = 2.25 V -30 -112 -30 -112 rnA
lee
Vee
Vee =
5.5 V.
5.5 V. 28 28 rnA !::
::J
tAli typical values are at Vee = 5 V, TA = 25°e. ()
;The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' a:
()
CJ)
«
c
z
«
CJ)
...I
«
83 PRODUCT PREVIEW
development. T exa. Instruments ..sarves the right to
TEXAS 2-249
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
R1 = 500 n,
FROM TO R2 = 500 n,
PARAMETER UNIT
SN54AS251 SN74AS251
tpLH 5 5
A, B,or C y ns
tpHL 5 5
tpLH 4.5 4.5
A, B, or C W ns
tpHL 4.5 4.5
tpLH 3 3
Any D Y ns
tpHL 4 4
tPLH 3 3
Any 0 W ns
tPHL 2.5 2.5
tpZH 5 5
IT Y ns
tpZL 6 6
tpZH 5 5
IT W ns
tpZL 6 6
tpHZ 3 3
G y ns
..
tpLZ 4 4
tpHZ 3 3
G W ns
tpLZ 4 4
tAli typical values are at Vee = 5 V. TA = 25°e .

Additional Information on these products can be obtained from the factory as it becomes available.
l>
r-
m
l>
2
C
l>
m
Q
::XJ
o
c
=i
m
PRODUCT PREVIEW 12€

This page contalns Informetlon on 8 product under
2-250 development. Tex.slnstrumenls reserv•• the right to
change or dl.contfnue thl. product without notice.
TEXAS
INSTRUMENTS
02661, APRil 1982-REVISED DECEMBER 1983
• Three·State Versions of 'ALS 153 and 'AS 153 SN54ALS253, SN54AS253 ••• J PACKAGE
SN74ALS253, SN74AS253 ... N PACKAGE
• Permits Multiplexing from N Lines to 1 Line
ITOPVIEWI
• Performs Parallel·to-Serial Conversion
• Fully Compatible with Most TTL Circuits VCC
2<3
• Package Options Include Both Plastic and Ceramic lC3 A
Chip Carriers in Addition to Plastic and Ceramic DIPs lC~ 2C3
• Dependable Texas Instruments Quality and Reliability lCl 2C2
2Cl
description lY 2CO
GND 2Y
Each of these data selectors/multiplexers contains inverters and
drivers to supply full binary decoding data selection to the AND-
OR gates. Separate output control inputs are provided for each of
the two four-line sections.
SN54ALS253, SN54AS253 ••• FH PACKAGE
The three-state outputs can interface with and drive data lines of SN74ALS253, SN74AS253 •.. FN PACKAGE
bus-organized systems. With all but one of the common outputs ITOPVIEWI
disabled (at a high-impedance state) the low-impedance of the U
single enabled output will drive the bus line to a high or low logic It!) u ult!)
CO.-Z>N
level. Each output has its own strobe (G). The output is disabled
3 2 1 2019
when its strobe is high.
A
The SN54ALS253 and SN54AS253 are characterized for 2C3
operation over the full military temperature range of - 55°C to NC
125°C. The SN74ALS253 and SN74AS253 are characterized 2C2
for operation from 0 °C to 70°C. 2Cl
>-ou>-o
en
'-ZZNU
t!) N
!::
::)
u
a:
FUNCTION TABLE
u
OUTPUT en
SELECT
INPUTS
DATA INPUTS
CONTROL
OUTPUT logic symbol
«
B
X
A
X
CO
X
Cl
X
C2
X
C3
X
G
H
Y
z c
2:
l
L
l
L
l
H
X
X
X
X
X
X
X
L
L
L
L
H
L B
«
L
L
H
H
X
X
L
H
X
X X L H en
..J
H
H
L
L
X
X
X
X H
L X
X
L
L
L
H
lG
lCO
«
H H X X X L L L (7)
H H X X X H L H lCl lV
lC2
Address inputs A and B are common to both' sections.
lC3
2~
2CO
(9)
2Cl 11 2V
2C2 (12)
2C3 (13)

33
TEXAS 2-251
INSTRUMENTS
1CO ...;(~6.:...)- - - - - - - - H I - - I
1C1 J(~5)~___________+=f~~
OUTPUT
DATA 1
1Y
SELECT
DATA 2 OUTPUT
2Y
(15)

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output ...... ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS253, SN54AS253 . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
. SN74ALS253,SN74AS253 . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
·121
2-252 TEXAS
INSTRUMENTS
DUAL 1 of' 4 DATA SELECTORS/MULTIPLEXERS

UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOL = 12mA 0.25 0.4 . 0.25 0.4
VOL V
Vee = 4.5 V, IOl = 24 mA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
IOZl Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
IO~ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V

I Outputs enabled 6.5 12 6.5 12
mA
I Outputs disabled 7.5 14 7.5 14 en
tAli tYPIcal values are at Vee = 5 V, TA = 25°e.
~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
t::
:::>
switching characteristics (see Note 1) ua:
Vec
CL
= 4.5 V to 5.5
= 50 pF,
V,
U
= 500 n, en
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
R1
R2 = 500 n, UNIT «
TA = MIN to MAX c
SN54ALS253 SN74ALS253 z
tplH
MIN
5
MAX
25
MIN
5
MAX
21
«
tpHl
A or B Any Y
5 25 5 21
ns en
....I
tplH
tpHl
Data (Any e) Any Y
2
3
12
17
2
3
10
14
ns «
tpZH 3 17 3 14
G Any Y ns
tpZL 4 19 4 16
tpHZ 2 12 2 10
G Any Y
2 14
ns
tpLZ 2 16
NOTE 1: For load circuit and voltage waveforms, see page '·12.
TEXAS 2-253
INSTRUMENlS

SN54AS253 SN74AS253
UNIT
SN54AS253 SN74AS253
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = -2mA vee- 2 vee- 2
VOH Vee = 4.5 V, 10H = -12 mA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 mA 2.4 3.2
Vee = 4.5 V, 10L = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, 10L = 48 mA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 50 50 '/lA
IOZL Vee = 5.5 V, Vo = 0.4 V -50 -50 /lA
A,8 0.2 0.2
II Vee = 5.5 V, VI = 7 V mA
All others 0.1 0.1
A,8 40 40
IIH Vee = 5.5 V, VI = 2.7 V /lA
All others 20 20
A,B -1 -1
10* Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
lee Vee = 5.5 V I Outputs low 20 32 20 32 mA

,
Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 5000, .
FROM TO
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n, UNIT
TA = MIN to MAX
SN54AS253 SN74AS253
MIN MAX MIN MAX
tpLH 4 14.5 4 13.5
A or B Y ns
tpHL 4 12 4 11.5
tpLH 3 8.5 3 7.5
Data (Any e) y ns
tpHL 3 8.5 3 8
tpZH 4 13 4 12.5
G Any Y ns
tpZL 4 12 4 11.5
tpHZ 2 6.5 2 6
G Any Y ns
tPLZ 2 8 2 7
12!
2-254 TEXAS
INSTRUMENlS
QUADRUPLE 1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
D2661,APRIL 1982-REVISED DECEM8ER 1983
• Three-State Outputs Interface Directly with System SN54ALS', SN54AS' ... J PACKAGE
Bus SN74ALS', SN74AS' •.. N PACKAGE
(TOP VIEW)
• Provides Bus Interface from Multiple Sources in High-
Performance Systems VCC
G
4A
4B
• Dependable Texas Instruments Quality and Reliability 4Y
3A
description 2Y 3B
GND -""'_ _...r- 3Y
These devices are designed to multiplex signals from four-bit
data sources to four-output data lines in bus-organized systems.
The 3-state outputs will not load the data lines when the output
control pin (3) is at a high-logic level.
SN54ALS', SN54AS' ... FH PACKAGE
The SN54' family is characterized for operation over the full SN74ALS', SN74AS' •.. FN PACKAGE
military temperature range of - 55 DC to 125 DC. The SN74' family (TOP VIEW)
is characterized for operation from 0 DC to 70 DC.
~ u ~
~I« Z >I<!J
3 2 1
1B 4 4A
logic symbols 1Y 5 4B
NC 6 NC
2A 7 4Y
'ALS257, 'AS257 'ALS258, 'AS258 2B 8 3A
AlB AlB
>-OU>-co
NZZ('t)('t) en
<!J
t::
1A 1A
::>
lY 1Y (J
lB
2A
1B
2A
a:
2Y 2Y (J
2B 2B FUNCTION TABLE
3A
3B
3Y
3A
3Y en
4A
3B
4A OUTPUT
INPUTS OUTPUTY <t
(13) 4Y 4Y SELECT DATA 'ALS257 'ALS258
4B 4B CONTROL C
G
AlB A B 'AS257 'AS258
z
H
L
X
L
X
L
X
X
Z
L
Z
H
<t
Pin numbers shDwn are for J and N packages.
L L H X H L en
...J
L H X L L H
L H X H H L <t

33
TEXAS 2-255
INSTRUMENTS
QUADRUPLE 1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
'ALS257, 'AS257 'ALS258, 'AS258
1A .....:..::.:.....-----J--/ (4) 1A
(4) 1Y
1Y
1B
2A~:""'---~-J--/ (7) 2A
2Y (7) 2Y
2B~~---+-+-~ 2B
(9) JA
JY (9) JY
JB~~---+-+--I JB
4A~~---+-J--/
(12) 4A
(12) 4Y
4Y
4B~~---~-J--/ 4B
AlB AlB
_ Pin numbers shown are for J and N packages.
»
r-
en absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
»
z Supply voltage, Vee ................................................................. 7 V
Input voltage ...................... '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7. \J
c Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
»
en
Operating free-air temperature range: SN54ALS', SN54AS' ....................... : .. - 55°C to 125°C
SN74ALS', SN74AS' .............................. ooe to 70°
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50 °e
o
::D
o
c
=i
en
2-256 TEXAS
- INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS, TexAS 75265
QUADRUPLE 1 OF 8 DATA SELECTORS/MULTIPLEXERS WITH 3·STATE OUTPUTS

VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee'; 4.5 V, IOL = 12mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V IOL =·24 mA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
IOZL Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA en
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A t::
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA :::::»
lo~ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA (.)
Outputs high 3 6 3 6 a:
'ALS257 Vee = 5.5 V Outputs low 8 12 8 12 (.)
mA en
lee
'ALS258 Vee = 5.5 V

Outputs high
Outputs low
2.5
7
4
11
2.5
7
4
11
«
Outputs disabled 8 13 8 13 c
z
«
en
....
«
33
TEXAS 2-257
INSTRUMENTS
, ALS257 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO Rl = 500 n.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 12 2 10
A or B Any Y ns
tpHL 3 14 3 12
tPLH 7 21 7 18
AlB Any Y ns
tpHL 6 25 6 22
tpZH 4 20 4 16
G Any Y ns
tpZL 5 22. 5 18
tpHZ 2 12 2 10
G Any Y
4 18. 4 15
ns
tpLZ

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO Rl = 500 n.
~
PARAMETER UNIT
TA = MIN to MAX
»
r- MIN
SN54ALS258
MAX
SN74ALS258
MIN MAX
en tpLH
A or 8 Any Y
2 10 2 8
ns
»
2
tpHL
tpLH
A/S Any Y
2
5
9
28
2
5
7
25
ns
tpHL 8 23 8 20
C tpZH 5 20 5 18
G
»
en
tpZL
tpHZ
Any Y
5
2
20
12
5
2
18
10
ns
G Any Y ns
o tpLZ 5 20 5 18
::a NOTE 1: For load circuit and voltage waveforms. see page 1·12.
o
C
=i
en
12E
2-258 TEXAS
INSTRUMENTS

SN54AS257 SN74AS257
SN54AS257 SN74AS257
SN54AS258 . SN74AS258
-18 mA -1.2 -1.2 V
Vce = 4.5 V to 5.5 V, IOH = -2 mA vee- 2 vee- 2
VOH Vee = 4.5 V, 10H = -12 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -15 mA 2.4 3.2
Vee = 4.5 V, 10L = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V IOL = 48 mA 0.35 0.5
10ZH Vee = 5.5 V, Va = 2.7 V 50 50 p.A
10Zl Vee = 5.5 V, Va = 0.4 V -50 - 50 p.A
A, Bar G 0.1 0.1
AlB 0.2 0.2
A, B, or G 20 20
IIH Vee = 5.5 V, VI = 2.7 V p.A
'AlB 40 40
A, B, orG -0.5 -0.5
AlB -1 -1
10:1: Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA
Outputs high 12.1 19.7 12.1 19.7
'AS257 Vee = 5.5 V Outputs low 19 30.6 19 30.6
Outputs disabled 19.7 31.9 19.7 31.9
ICC mA
Outputs high 8.4 13.5 8.4 13.5
'AS258 Vee = 5.5 V Outputs low 15.2 24.6 15.2 24.6
Outputs disabled 15.5 25.2 15.5 25.2

33
TEXAS 2-259
INSTRUMENTS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
SN54AS257 SN74AS257
MIN MAX MIN MAX
tpLH 1 6.5 1 5.5
A or B Any Y ns
tpHL 1 7 1 6
tPLH 2 12 2 11
AlB Any Y ns
tpHL 2 10.5 2 10
tpZH 2 8.5 2 7.5
G Any Y ns
tpZL 2 10.5 2 9.5
tpHZ 1.5 8 1.5 6.5
G Any Y ns
tpLZ 2 8 2 7
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
= 500 n.
IB
(INPUT) (OUTPUT) R2
TA = MIN to MAX
SN54AS258 SN74AS258
l> MIN MAX MIN MAX
r- tpLH 1 5.5 1 5
en tpHL
A or B Any Y
1 5 1 4
ns
l> tpLH
AlB Any Y
2 11 2 9.5
ns
2 tpHL 2 11 2 10
C tpZH
G Any Y
2 8.5 2 8
ns
tpZL 2 11 2 10
l>
en tpHZ
tpLZ
G Any Y
1.5
2
7
8.5
1.5
2
6
6.5
ns
('")
:ll
('")
C
::j
en
12e
2-260 TEXAS
INSTRUMENTS
8·BIT ADDRESSABLE LATCHES
• 8-Bit Parallel-Out Storage Register Performs Serial-to- SN54ALS259 . . . J PACKAGE

Parallel Conversion with Storage SN74ALS259 . . . N PACKAGE
(TOP VIEW)
• Asynchronous Parallel Clear
SO VCC
• Active High Decoder
S1 ClR
• Enable/Disable Input Simplifies Expansion S2 G
QO 0
• Expandable for N-Bit Applications Q1 Q7
• Four Distinct Functional Modes Q2 Q6
Q3 Q5
• Package Options Include Both Plastic and Ceramic GND Q4
Chip Carriers in Addition to Plastic and Ceramic DIPS --",.-----'-
• Dependable Texas Instruments Quality and Reliability SN54ALS259, ,FH PACKAGE

SN74ALS259. . FN PACKAGE
description (TOP VIEW)
These B-bit addressable latches are designed for general purpose o U U~

U...J
storage applications in digital systems. Specific uses include en UlZ>
working registers, serial-holding registers, and active-high 3 2 1 2019
decoders or demultiplexers. They are multifunctional devices S2 4 18
capable of storing single-line data in eight addressable latches, QO 5 17 D
and being a 1-of-B decoder or demultiplexer with active-high NC 6 16 NC
outputs. Q1 7 15 07
Q2 8 14 06
Four distinct modes of operation are selectable by controlling the
9' 10 11 1213
clear (elR) and enable (G) inputs as enumerated in the function
table. In the addressable-latch mode, data at the data-in terminal MOU'<tLn
OZZOO
is written into the addressed latch. The addressed latch will (!)
follow the data input with all unaddressed latches remaining in

their previous states. In the memory mode, all latches remain in
en
their previous states and are unaffected by the data or address
!::
logic symbol :::>
inputs. To eliminate the possibility of entering erroneous data in
the latches, enable G should be held high (inactive) while the
u
address lines are changing. In the 1-of-8 decoding or
a:
demultiplexing mode, the addressed output will follow the level U
of the D input with all other outputs low. In the clear mode, all en
outputs are low and unaffected by the address and data inputs. «
The SN54AlS259 will be characterized for ope!ation over the c
full military temperature range of - 55°C to 125°C. The 14) :2
SN74ALS259 will be characterized for operation from ooC to
15)
00
«
70°C. 01 en
-J
FUNCTION TABLE LATCH SELECTION TABLE

9.20
10,2R
02 «
9,30
OUTPUT OF EACH SELECT INPUTS LATCH 03
10;JR
I INPU~ S2 Sl SO ADDRESSED
ADDRESSED OTHER FUNCTION 9.40 19)
CLR G L L L 0 04
LATCH OUTPUT
L L H 1 10AR
H L 0 °iO Addressable Latch L H L 2 9.50 110) 05
H H QiO °iO Memory L H H 3
10;5R
L L 0 L B-Line Demultiplexer H L L 4
H L H 5 9,60 11) 06
L H L L Clear
H H L 6 10~R
o• the level at the data input. H H H 7
9.70 112) 07
010. tholoyel of OJ Ii = O. 1. . . . .7. as appropriate) before
the indicated steady-state input conditions were
10.7R
established. Pin numbers shown are for J and N packages.

!82
ThI. document contain. information on a product under
development. Texa.ln.trumonts raservo. the right to TEXAS 2-261
INSTRUMENTS
lB·
l>
r-
en
l>
:2
C
l>
en
o
:D
o
c
=i
en
2-262
LOOK-AHEAD CARRY GENERATORS FOR COUNTERS
• Performs Look-Ahead Carry Across n-Bit SN54AS264 ... J PACKAGE

Counters SN74AS264 ... N PACKAGE
(TOP VIEW)
• Accommodates Actiye-High or Active-Low
Carry A1 VCC
81 82
• Improves Cascaded Counters System AO A2
Performance 80 CE
• Dependable Texas Instruments Quality and A3 CO
Reliability 83 C1
RCD8 RCDA
description GND C2
This look-ahead generator was designed

specifically to perform a carry-anticipate across SN54AS264 ... FH PACKAGE
any number of n-bit counters, thus increasing
(TOP VIEW)
system clock frequency. A carry enable CE, and
carry outputs RCOA and RCOB are provided for U
. ..-"- U UN
n-bit cascading. [])~z>[])
The counter can be used with either active-high-

carry or active-low-carry counters. For active- A2
high-carry counters, CE is active high, the A set CE
of inputs and output RCOA are used, and the B NC
set of inputs are connected to a low logic level. CO
For active-low-carry counters, CE is active low, 83 C1
the B set of inputs and output RCOB are used,
and the A set of inputs are connected to a high [])ClUN~
logic level. See Figures 1 and 2 for typical ozzUo
U(!) U
applications. a: a:
The SN54AS264 is characterized for operation NC - No internal connection

over the full military temperature range of
- 55°C to 125°C. The SN74AS264 is
characterized for operation in the temperature
range of OOC to 70°C.
positive logic equations

ACTIVE-HIGH·CARRY COUNTERS ACTIVE·LOW·CARRY COUNTERS
(CE Is high. all B inputs are low) (CE is low. all A inputs are high)
CO = AO CO = BO
C1 = AO. A1 C1 = BO· B1
C2 = AO • A 1 • A2 C2 = BO • B1 • B2
RCOA = AO • A 1 • A2 ·A3 RCOA = B1 • B2 • B3
RCOB is high RCOB = BO • B1 • B2 • B3

13 PRODUCT PREVIEW
ThIs document COfItMIo information on. product under TEXAS·
development. rexa.lnltrumentl ,e..rval the right to 2-263
change 0' dlocontlnua this product without notice. INSTRUMENTS
TYpES SN54AS264. SN74AS264
LOOK·AHEAD CARRY GENERATORS FOR COUNTERS
FUNCTION TABLE FOR CO OUTPUT logic symbols

INPUTS OUTPUT
ACTIVE·HIGH INPUTS
AO BO CE CO
H H X H [CLA FOR CTRSI
H X H H
L X X L 1,3
CE (13) CO
X L L L Z.1 2,3
BO (4) Z2 1.3,5
FUNCTION TABLE FOR C1 OUTPUT
2.3,5 C1
INPUTS OUTPUT (3)
AO G3 4,5
A1 AO B1 BO CE C1
(2) 1.3,5,7
H" X H X X H B1 Z4
H H X H X H 2,3,5,7
(11 4.5,7 C2
H H X X H H A1 G5
L X X X X L 6,7
(15)
X L L X B2 Z6
X L
1.3,5,7,9
X X L L L L (14)
A2 G7 4,5,7,9
RCOA
6,7,9
FUNCTION TABLE FOR C2 OUTPUT
B3 ZS S,9
INPUTS OUTPUT
A2 A1 AO B2 B1 BO CE C2 A3 G9
H X X H X X X H
4 RCOB
H H X X H X X H
6
H H H X X H X H
1m H
L
X
H
X
L
H
X
X
X
X
L
X
X
X
X
X
X
H
X
X
H
L
L ACTIVE·LOW INPUTS
l> X X L L L X X L
r- X X X L L L L L [CLA FOR CTRSI
en
l> FUNCTION TABLE FOR RCOA OUTPUT 1,2
2 . INPUTS OUTPUT
21
C A3 A2 A1 AO B3 B2 B1 CE RCOA G2 5
BO
l> H X X X H X X X H 3,4
en H H X X X H X X H AO Z3 1,2,4
(') H H H X X X H X H
H H H H X X X H H B1 G4 7
::D L X X X X X X X L 5,6
(') A1 25 3,4,6
X L X X L X X X L
C 1,2,4,6
X X L X L L X X L
~ X X X L L L L X L
G6
en X X X X L L L L L Z7 7,S
5,6,8
FUNCTION TABLE FOR RCOB OUTPUT GS 3,4,6,8
1,4,6,8
INPUTS OUTPUT
Z9
B3 B2 B1 BO CE RCOB
H X X X X. H
X H X X X H
X X H X X H
X X X H X H
X X X X H H
L L L L
12f
2-264 TEXAS
INSTRUMENTS
CE (13)
rr,~====r-~~ ________~(7~) RCOB
B3 (6)
A3 (5)
B2 (15)
A2 (14
B1 (2)
A1 (11
en
t:
:::l
(4)
U
BO (3)
AO~-----"---f a:
U
absolute maximum ratings over free-air temperature (unless otherwise noted)
en
<t
Input voltage .............................................................. 7 V
o
Operating free-air temperature range: SN54AS264 ....................... - 55 °e to 125°e
2
SN74AS264 ........................... 0 0 eto70oe
<t
Storage temperature range ......................................... - 65 °e to 150 0 e en
-I
<t
SN54AS264 SN74AS264
UNIT
TEXAS 2-265
INSTRUMENTS
electrical characteristics over recommended operating free"air temperature range

\
SN54AS264 SN74AS264
VIK VCC = 4.5 V. II = -18 rnA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V. 10H = -2 rnA Vee- 2 Vee- 2 V
VOL VCC = 4.5 V. 10L = 20 rnA 0.3 0.5 0.3 0.5 V
CE 500 500
AO.A2 700 700
Al 800 800
II VCC = 5.5 V. VI = 7 V p.A
A3. BO. Bl 400 400
B2 300 300
B3 200 200
CE 100 100
AO.A2 140 140
Al 160 160
IIH VCC = 5.5 V. VI = 2.7 V p.A
A3. BO. Bl 80 80
B2 60 60
B3 40 40
CE -2.5 -2.5
AD -3.5 -3.5
Al. A2 -4 -4
IlL VCC = 5.5 V. VI = 0.4 V
..;.2
rnA
A3. BO. Bl -2
B2 -1 -1
B3 -1.5 -1.5
~ 10i
ICCH
VCC = 5.5 V
VCC = 5.5 V
Vo = 2.25 V -30
26
-112 -30
26
-112 rnA
rnA
>
r-
ICCL 28 28
en t All typical values are at Vee = 5 V. T A = 25°e. I
iThe output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current. lOS'
>
2 switching characteristics (see Note 1)
C Vec = 4.5 V to 5.5 V.
= 50 pF.
>
en PARAMETER
FROM TO
CL
RL = 50 n.
UNIT
o SN54AS264 SN74AS264
:a MIN Typt MAX MIN Typt MAX
o tPLH 6 6
c tpHL
CE CO.Cl.C2
5 5
ns
=i tpLH 5 5
en tpHL
An or Bn CO. Cl. C2
5 5
ns
tPLH 5 5
An. Bn. or CE RCOA ns
tpHL 5 5
tpLH 5 5
Bn or CE RCOB ns
tpHL 5 5

12f
2-266 TEXAS '

INSTRUMENTS
TYPICAL APPLICATION INFORMATION

The circuit shown in Figure 1 illustrates how the' AS624 can implement look-ahead carry for the active-
high-carry 'AS 163, while Figure 2 shows the look-ahead carry for the active-low-carry' AS169.
CLOCK
'AS163
CLK
L 'AS1.'
PCLK
L PCLK
'AS16' 'AS163
PCLK
COUNT ENP RCa ..-- ENP RCa ,...--- ENP RCa .--- ENP RCa
H - ENT H - ENT H - ENT H - ENT
L L L L
I I I I
AO BO CO A1B1Cl A2 B2 C2 A3B3
' - - CE RCOA f--
FIGURE l-ACTIVE-HIGH-CARRY
'AS169
C LOCK ----II~C>
COUNT - - i _ - d RCa
en
!::
:::J
U
FIGURE 2-ACTlVE·LOW·CARRY CC
U
en
«
c
z
«
en
...J
«
:83
TEXAS 2-267
INSTRUMENlS
1m
l>
r-
CI>
l>
:2
C
l>
CI>
n
::IJ
n
c
=i
CI>
2-268
OCTAL O·TYPE FLlp·FLOPS WITH CLEAR
02661, APRil 1982 - REVISED DECEMBER 1983
• Contains Eight Flip-Flops with Single-Rail SN54ALS273 • • . J PACKAGE

Outputs SN74ALS273 • • • N PACKAGE
(TOP VIEW)
• Buffered Clock and Direct Clear Inputs
• Individual Data Input to Each Flip-Flop ClR VCC
• Applications Include: 10 80
Buffer/Storage Registers 10 80
Shift Registers 20 70
Pattern Generators 20 70
30 60
• Package Options Include Both Plastic and 3D 60
Ceramic Chip Carriers in Addition to Plastic 50
40
and Ceramic DIPs
40 50
• Dependable Texas Instruments Quality and GNO ClK
Reliability
description
SN54ALS273 . • . FH PACKAGE
These monolithic. positive-edge-triggered flip-flops
SN74ALS273 • • . FN PACKAGE
utilize TTL circuitry to implement Ootype flip-flop
(TOPVIEWI
logic with a direct clear input.
Information at the 0 inputs meeting the setup time

requirements is transferred to the 0 outputs on the
015
o u>oo
...... ~o
positive-going edge of the clock pulse. Clock trigger-
ing occurs at a particular voltage level and is not 20 80
directly related to the transition time of the positive- 20 70
going pulse. When the clock input is at either the high 30 70
or low level. the 0 input signal has no effect at the' 30 60 en
output. 40 60 !::
The SN54AlS273 is characterized for operation :J
over the full military temperature range of - 55°C to (J
125 DC. The SN74AlS273 is characterized for a:
operation from ooC to 70°C. (3
en
logic symbol «
FUNCTION TABLE c
2
(EACH FLIP·FLOP)
INPUTS OUTPUT
ClK «
CLEAR CLOCK 0 0 10 lQ en
-J
H
L X
t
X
H H
L 20
3D
20
«
H t L L
H L X 50
00
60 60
70
80

83
. TEXAS 2-269
INSIRUMENlS
OCTAL D·TYPE FLlp·FLOPS WITH CLEAR
10 20 30 40 50 60 70 80
(3) (4) (7) (8) (13) (14) (17) (18)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
..
Operating free-air temperature range: SN54ALS273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 1 50 °e

»
r- SN54ALS273 SN74ALS273 UNIT
en MIN NOM MAX MIN NOM MAX
»
:2
VCC
VIH
Supply voltage
High-level input voltage
4.5
2
5 5.5 4.5
2
5 5.5 V
V
o VIL
IOH
Low-level input voltage
High-level output current
0.8
-1 -2.6
0.8 V
mA
»
en IOL Low-level output current 12 24 mA
~
fclock Clock frequency
Pulse duration
ClR low
ClK high
10
16.5
0 30
. 10
14
0 35 MHz
ns
tw
::D ClK low 16.5 14
(')
c: tsu
Setup time
before CLKI
Data
Clear inactive state
10
15
10
15
ns
=i
en th
TA
Hold time, data after ClK I
Operating free-air temperature
0
-55 125
0
0 70
ns
°c
12f
2-270
TEXAS .
INSTRUMENTS
OCTAL D·TYPE FLlp·FLOPS WITH CLEAR
VIK VCC = 4.5 V. II = -18 rnA -1.5 -1.5 V
VCC = 4.5 V to 5.5 V. 10H = -0.4 rnA vee- 2 Vee- 2
VOH VCC = 4.5 V. 10H = -1 rnA 2.4 3.3 V
VCC = 4.5 V. 10H = -2.6 rnA 2.4 3.2
VCC = 4.5 V. 10L = 12 rnA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V. 10L = 24 rnA 0.35 0.5
II VCC = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH VCC = 5.5 V. VI = 2.7 V 20 20 p.A
IlL VCC = 5.5 V. VI = 0.4 V -0.2 -0.2 rnA
10* VCC = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
ICCH VCC = 5.5 V 11 20 11 20
rnA
ICCL VCC = 5.5 V 19 29 19 29

*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, 105'
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO RL = 500 n,
PARAMETER UNIT
MIN MAX MIN MAX
f rnax 30 35 MHz
tPLH 2 16 2 12
CLR Any Q ns
tPHL 3 17 3 15
33
TEXAS 2-271
INSTRUMENlS
2-272
9·81T PARITY GENERATORS/CHECKERS
02661. DECEMBER 19B2-REVISED DECEMBER 19B3
• Generates Either Odd or Even Parity for Nine SN54AS280 ... J PACKAGE
Data Lines SN74AS280 .•. N PACKAGE
ITOPVIEW)
• Cascadable for n-Bits Parity
G VCC
• Can Be Used to Upgrade Existing Systems F
H
using MSI Parity Circuits E
NC
• Package Options Include Both Plastic and I 0
Ceramic Chip Carriers in Addition to Plastic, ~EVEN C
and Ceramic DIPs ~ODD B
GND A
Reliability
SN54AS280 .•. FH PACKAGE

FUNCTION TABLE
ITOP VIEW)
NUMBER OF INPUTS A OUTPUTS
U
THRU I THAT ARE HIGH 1: EVEN 1:000 U U
0,2.4,6,8
::I:t!)z>u.
H L
1,3,5,7,9 L H
NC E
NC NC
logic symbol I o
NC NC
2k ~EVEN C
18)
A
19)
B
110) OOU<l:CD
C
15) I: ozz
111) ot!)
0
112) EVEN ~ en
E
F
113) 16) I:
t:::
G
11) ODD :J
H
12) U
I
14) a:
U
en
<t
description C
These universal, monolithic, nine-bit parity generators/checkers utilize Advanced Schottky high-performance circuitry Z
and feature odd and even outputs to facilitate operation of either odd or even parity application. The word-length <t
capability is easily expanded by cascading. en
-J
These devices can be used to upgrade the performance of most systems utilizing the '180 parity generator/checker.
Although the 'AS280 is implemented without expander inputs, the corresponding function is provided by the
<t
availability of an input at pin 4 and the absence of any internal connection at pin 3. This permits the' AS280 to be
substituted for the '1 BO in existing designs to produce an identical function even if 'AS280's are mixed with existing
'180's.
All 'AS280 inputs are buffered to lower the drive requirements.

The SN54AS280 is characterized for operation over the full military temperature range of - 55 °C to 125 °C. The
SN74AS280 is characterized for operation from 0 °C to 70 o C.
Copyright © 1982 Texas Instruments Incorporated

:83 PRODUCT PREVIEW
This document contalnalnfonnatlon on a product under
development. Texa.lnstrumentl r.serves the right to TEXAS 2-273
logic diagram
l:
EVEN
l:
ODD
- l>
r-
en
l>
2
C
l> absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
en Supply voltage, Vee ........................................ ~ . . . . . . . . . . . . . . . . . . . . . . .. 7 V
o Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Xi Operating free-air temperature range: SN54AS280... . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°C
o SN74AS280 ................................... ooe to 70°C
c: Storage temperature range ................... ' ............................. " - 65°C to 1 50°C
=i
en recommended operating conditions
SN54AS280 SN74AS280
UNIT
- MIN NOM MAX MIN NOM MAX
12:
2-274 TEXAS .
INSTRUMENTS
SN54AS280 SN74AS280
VIK Vee ~ 4.5 V. II ~ -18 mA -1.2 -1.2 V
VOH Vee ~ 4.5 V to 5.5 V. 10H ~ -2 mA Vee- 2 Vee- 2 V
VOL Vee ~ 4.5 V. 10L ~ 20 mA 0.35 0.5 0.35 0.5 V
II Vee ~ 5.5 V. VI ~ 7 V 0.1 0.1 mA
IIH Vee ~ 5.5 V. VI ~ 2.7 V 20 20 p.A
IlL Vee ~ 5.5 V. VI ~ 0.4 V -0.5 -0.5 mA
10+ Vee ~ 5.5 V. Vo ~ 2.25 V -30 -112 -30 -112 mA
lee Vee ~ 5.5 V 27 27 mA
= 5 V. TA = 25 ce.
t All typical values are at Vee
+The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS.

Vcc ~ 4.5 V to 5.5 V.
CL ~ 50 pF.
PARAMETER
FROM TO RL ~ 500 n. UNIT
(INPUT) (OUTPUT) TA ~ MIN to MAX
SN54AS280 SN74AS280
tpLH 7 7
Any E Even ns
tPHL 7.5 7.5
tPLH 7 7
Any E Odd ns
tPHL 7.5 7.5
+AII typical values are at Vee = 5 V. TA = 25 ce.

en
NOTE 1: For load circuit and voltage waveforms, see page 1·12. t::
::>
u
a:
u
en
«
c
2:
«
en
...J
«
283
TEXAS 2-275
INSTRUMENTS
25·LlNE PARITY/GENERATOR CHECKER 81·LINE PARITY/GENERATOR CHECKER
l: l:
EVEN EVEN
'AS280 'AS280
l:
000
A
l: B
EVEN
l: H = EVEN C l: H = EVEN
EVEN L=OOO EVEN L=ODD
'AS280 'AS280 'AS280
l: H =000 l: H = EVEN
ODD L = EVEN ODD L=ODO
-
l: l:
EVEN EVEN
'AS280 E 'AS280
F ~
G TO OTHER
H 'AS280's
>
r-
en Three' AS280 can be used to implement a 25-line parity generator/checker. Longer word lengths can be implemented by cascading 'AS280. As shown
>
2
As an alternative, the outputs of two or three parity generators/checkers
here, parity can be generated for word lengths up to 81 bits.
can be decoded with a 2-input ('S86 or 'LS86) or 3-input ('S135) exclusive-

C OR gate for 18- or 27-line parity applications.
>
en
~
:D
(')
c
=i
en
128
2-276 TEXAS
INSTRUMENTS
LOOK·AHEAD CARRY GENERATOR WITH SELECTABLE CARRY INPUTS
• Selectable Carry Inputs Version of the SN54AS282 ... J PACKAGE

Popular '5182 Allows Double Precision SN74AS282 ..• N PACKAGE
(TOP VIEW)
Carry
• Offers Carry Functions in a Compatible G1 VCC
Form for Direct Connection to the ALU P1 P2
GO <32
o Cascadable to Perform Look-Ahead Across PO CnA
n-Bit Adders <33 CnB
P3 Cn + x
Ceramic Chip Carriers in Addition to Plastic SO Cn + y
S1 Cn '
and Ceramic DIPs
P G
4) Dependable Texas Instruments Quality and GND Cn + z
Reliability
SN54AS282 ... FH PACKAGE
PIN DESIGNATIONS SN74AS282 ... FN PACKAGE
ALTERNATIVE DESIGNATIONSt FUNCTION (TOP VIEW)
GO, Gl, G2, G3 GO, Gl, G2, G3 Carry Generate Inputs U
PO, Pl, P2, P3 PO, Pl, P2, P3 Carry Propagate Inputs 0.--'-- UN
It? Ia. It? > Ia.
CnA, CnB CnA, CnB Carry Inputs
Cn ' Cn ' Selected Carry
Cn + x , Cn + y , Cn + x , Cn + y ,
PO <32
Carry Outputs <33
Cn + z Cn + z CnA
G y Carry Generate Outputs P3 CnS
Carry Propagate SO Cn + x
p X S1 Cn + y
Outputs
SO, 51 Carry Select Inputs
VCC Supply Voltage en
GND Ground
!::
t Interpretations are illustrated in connection with the Function Tables for ::>
the 'AS181A and 'AS881A. ua:
description u
The' AS282 look-ahead carry generator is capable of anticipating a carry across four binary adders or group en
of adders. They are cascadable to perform full look-ahead across n-bit adders. The' AS282 is functionally «
the same as the SN54AS182/SN74AS182 except that the carry input (C n) is selected from CnA, CnS, C
and their complements CnA and enS. The logic equations are written in terms of the selected carry Cn· Z
This signal is also available as an output at Cn'. «.
When used in conjunction with the' AS181 A, 'AS881A, or 'AS888 arithmetic logic unit (ALU), this generator en
provides high-speed carry look-ahead capability for any word length. The' AS282 generates the look-ahead -I
(anticipated carry) across a group of four ALU's and, in addition, other carry across sections of four look- «
ahead circuits may be employed to anticipated carry across sections of four look-ahead packages up to
n-bits. The method of cascading' AS282 circuits to perform multi-level look-ahead is illustrated under typical
application data.
logic equations
Cn + x = GO + PO Cn Cn + x - YO (XO + Cn)
Cn +y = G1 +P1 GO+P1 POC n Cn +y = Yl [Xl + YO (XO + Cn)]
Cn+ z = G2 + P2 Gl + P2 Pl GO + P2 Pl PO Cn or C n +z = Y2 {X2 + Yl [Xl + YO (XO + Cn)]}
G = G3 + P3 G2 + P3 P2 Gl + P3 P2 Pl GO Y = Y3 (X3 + Y2) (X3 + X2 + YlI (X3 + X2 + X1 + YO)
P = P3 P2 Pl PO X = X3 + X2 + Xl + XO

283
TEXAS 2-277
INSTRUMENTS
FUNCTION TABLE FOR G OUTPUT logic diagram (positive logic)

INPUTS OUTPUT (9) P
G3 G2 G1 GO P3 P2 P1 G
L X X X X X X L
X L X X L X X L
X X L X L L X L
X X X L L L L L
All other combinations H P3 -H1-+4++~1"""'\
.:.;;(6..:-)
G3 (5)
FUNCTION TABLE FOR ji OUTPUT
INPUTS OUTPUT
P3 P2 P1 PO P
L L L L L
All other
H
P2 ~H-4-+++-I-r'
combinations G2 (18)
FUNCTION TABLE
FOR Cn ' OUTPUT
INPUTS OUTPUT
51 SO Cn '
L L CnA
L H CnA
H L CnB
H H CnB
FUNCTION TABLE
1m FOR Cn + x OUTPUT
INPUTS OUTPUT
>
r-
GO
L
PO
X
Cn'
X
Cn + x
H
en X L H H
>
:2
All other
combinations
L logic symbol
o FUNCTION TABLE Cn + y OUTPUT
CPG
> MUX
en
~
61
L
GO
X
INPUTS
P1
X
OUTPUT
PO
X
Cn '
X
Cn + y
H
so
St
(7)
(8)
o}
1
G0-
3
::u X L L X X H (17) 0
o X X L L H H ~1 - Z4
(13)
c: All oth~r
L
(16) 2
4
=i combinations
~3 - -C1
en (4) COo
(15)
Cn +x
FUNCTION TABLE FOR Cn +z OUTPUT r...... CPO
INPUTS OUTPUT (3) ,...", (14)
CGO COt C n +y
G2 G1 GO P2 P1 PO Cn ' Cn + z (2) ,.....
cPt
L X X X X X X H (1) ,.... CGt CO2
(11)
Cn +z
X L X L X X X H (19) ,...."
CP2 (9)
X X L L L X X H
(18) ,..... CP r--.
X X X L L L H H' CG2
(6) (12)
All other combinations L
(5) -~
" CP3
CG3
CG "-
H = high-level, L = low level, X = irrelevant.

Any inputs not shown in a given table are irrelevant with respect
to that output. Pin numb~rs shown are for J and N packages.
128:
2-278 TEXAS
INSTRUMENlS
LOOK-AHEAD CARRY GENERATOR WITH SELECTABLE CARRY INPUTS
Input voltage .............................................................. 7 V
Operating free-air temperature range: SN54AS282 ....................... - 55 °e to 125 °e
SN74AS282 ......................... " ooe
to 70 0 e
Storage temperature range ......................................... - 65 °e to 150 °e

SN54AS282 SN74AS282
UNIT
Vcc Supply voltage 4.5 5 5.5 4.5 5 5.5 V
Vil low·level input voltage 0.8 0.8 V
electrical characteristics over recommended operating free-air temperature range (unless otherwise
noted)
SN54AS282 SN74AS282
MIN TVPt MAX MIN TVpt MAX
VIK VCC = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH VCC = 4.5 V to 5.5 V, 10H = -2 mA Vee- 2 vee- 2 V
VOL VCC = 4.5 V, 10l = 20 mA 0.3 0.5 0.3 0.5 V
CnA, CnB 200 200
SO, Sl, P3 200 200
P2 300 300 CJ)
= =
II
PO, Pl, G3
VCC 5.5 V, VI 7 V
400 400
/LA
!::
GO,G2 700 700 ::>
Gl 800 800 u
CnA, CnB 40 40 a:
SO, Sl, P3 40 40 u
P2 60 60
IIH VCC = 5.5 V, VI = 2.7 V /LA CJ)
PO, Pl, G3
GO, G2
80
140
80
140
«
Gl 160 160 c
-1 -1 z
CnA, CnB
SO, Sl, P3 -1 -1 «
P2 -1.5 -1.5 CJ)
III VCC = 5.5 V, VI = 0.4 V mA
-l
PO, Pl, G3 -2 -2
GO, G2
Gl
-3.5
-4
-3.5
-4
«
lot VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
ICCH 22 22
VCC = 5.5 V mA
ICCl 26 26
t All typical values are at Vee = 5 v, T A = 25°e.

~The output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current, lOS'
1283
TEXAS 2-279
INSTRUMENTS

Vcc = 4.5 V to 6.6 V.
CL = 60 pF.
FROM TO RL = 600 n.
PARAMETER UNIT
SN64AS282 SN74AS282
tpLH SO. 51. 6 6
Cn' ns
tpHL CnA. or CnS '6 6
tPLH 50.51. Cn + X• Cn + y• 6 6
ns
tpHL CnA. or CnS Cn + z 6 6
tpLH Cn + X• Cn + y , 5 5
P or G ns
tpHL Cn + z 5 5
tpLH 6 6
PorG G ns '
tpHL 5 5
tPLH 5 5
P P ns
tPHL 5 5

NOTE1: For load circuit and voltage waveforms, see page 1-12,
~ CLOCK-+----__ ------------------------------------------------------------~
»
,...
en
»
:2
C
GO PO Cn +x 01 P1 Cn+y G2 P2 Cn+z G3 P3
»
en
CnB
CnA
'A5282 'A51B2
C') so SO
:xJ 51 51
C')
C FIGURE 1-32-BIT LOOK-AHEAD CARRY WITH DOUBLE-PRECISION CARRY IN 'AS282 AND 'AS182
~
CJ)
128,
2-280 TEXAS
INSTRUMENTS
9·BIT PARITY GENERATORS/CHECKER
WITH BUS DRIVER PARITY 110 PORT
02809 DECEM8ER 1983
• Generates Either Odd or Even Parity for SN54AS286 ••. J PACKAGE

Nine Data Lines SN74AS286 ••• N PACKAGE
(TOP VIEWI
• Cascadable for n-Bi~s Parity
G VCC
• Direct Bus Connection for Parity Generation H F
or for Checking by Using the Parity I/O Port XMIT E
D
• Glitch-Free Bus During Power Up/Down
PARITY ERROR C
• Package Options Include both Plastic and PARITY I/O B
Ceramic Carriers in Addition to Plastic and GND"-L_ _...r--A
Ceramic DIPs
• Dependable Texas Instruments Quality and SN54AS286 ..• FH PACKAGE
Reliability SN74AS286 ... FN PACKAGE
(TOP VIEWI
description U
u u
:I:l!)Z>u.
The SN54AS286 and SN74AS286 universal
nine-bit parity generators/checkers feature a 3 2 1 2019
local output for parity checking and a E
48-milliampere bus-driving parity I/O port for NC NC
parity generation/checking. The word-length I D
capability is easily expanded by cascading. NC NC
PARITY ERROR C
The XMIT control input is implemented
specifically to accommodate cascading. When
XMIT is low the parity tree is disabled and PE will QOX«aJ
;:,zz
remain at a high logic level regardless of the input >-l!)
l-
levels. When XMIT is high the parity tree is ii:
enabled. The Parity Error output will indicate a «
a.
CJ)
parity error when either an even number of
NC-NQ internal connection
t::
inputs (A through I) are high and Parity liD is ::J
forced to a low logic level. or when an odd ()
number of inputs are high and Parity I/O is a:
forced to a high logic level. ()
The I/O control circuitry was designed so that the I/O port will remain in the high-impedance state during CJ)
power-up or power-down to prevent bus glitches. «
The SN54AS286 is characterized for operation over the full military range of - 55 °e to 125°e. The c
SN74AS286 is characterized for operation from ooe to 70 oe. z
«
CJ)
..J
«

Z83 PRODUCT PREVIEW
This cIocunwIt contains Infonnatlon an 8 product w>der
development. Texallnltruments r..ervelthe right to TEXAS 2-281
chang. or dllcontlnue thil product without notice. INSTRUMENTS
POST OFFICE BOX 225012 e DALLAS. TEXAS 75265
WITH BUS DRIVER PARITY I/O PORT
FUNCTION TABLE
NUMBER OF INPUTS
PARITY PARITY
(A THRU I) THAT XMff
I/O ERROR
ARE HIGH
0, 2, 4, 6, 8 I H H
1,3,5,7,9 I L H
h h H
0,2,4,6,8
h I L
h h l
1,3,5,7,9
h I H
h - high input level I - low input level

H - high output level L - low output level
logic symbol logic diagram (positive ,logic)
(8)
A 2K
(9)
B
(10)
c
(11)
0
(12)
E
(13)
F
(1)
G
(2)
H
(4)
(3)
~
XMIT ENl
»
r-
C/)
»z absolute maximum ratings over operating free-air temperature range

Supply voltage, Vee .......................................................... 7 V
c Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
»
C/)
Voltage applied to a disabled 3-state output ...................................... 5.5 V
Operating free-air temperature range: SN54AS286 ....................... - 55 °e to 125 °e
SN74AS286 ........................... ooe to 70 0 e
o Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 140 °C
:lJ
o
c recommended operating conditions
=i
rJ)
SN54AS286 SN74AS286
UNIT
Parity error -2 -2
10H High-level output current mA
Parity I/O -12 -15
Parity error 20 10
10l low-level output current mA
Parity I/O 32 48
128
2-282 TEXAS
INSTRUMENTS
electrical characteristics over recommended free-air temperature range

SN54AS286 SN74AS286
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
All outputs Vee = 4.5 V to 5.5 V, 10H = -2 mA Vee- 2 Vee- 2
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
V
VOH
Parity I/O Vee = 4.5 V, 10H = -12 mA 2.4
Vee = 4.5 V, 10H = -15 mA 2.4
Parity error Vee = 4.5 V, 10L = 20 mA 0.35 0.5 0.35 0.5
VOL Vee = 4.5 V, 10L = 32 mA 0.5 V
Parity I/O
Vee = 4.5 V, 10L = 48 mA 0.5
Parity I/O Vee = 5.5 V, VI = 5.5 V 0.1 0.1
mA
II
All other inputs Vee = 5.5 V, VI =7V 0.1 0.1
Parity I/Ot 50 50
IIH Vee = 5.5 V, VI = 2.7 V
20 20
p.A
All other inputs
Parity I/Ot -0.5 -0.5
IlL Vee = 5.5 V, VI = 0.4 V -0.5 -0.5
mA
All other inputs
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Transmit 29 29
lee Vee = 5.5 V mA
Receive \ 34 34

tFor 1/0 ports. the parameters IIH and IlL include the off-state current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'

vcc = 4.5 V to 5.5 v, en
Cl = 50 pF,
R1 = 500O,
t::
PARAMETER
FROM TO
UNIT ::J
(INPUT) (OUTPUT) R2 = 500O, U
TA = MIN to MAX a:
SN54AS286 SN74AS286
U
tPLH 8 8 en
tpHL
Any A thru I Parity I/O
8.5 8.5
ns <3:
tpLH
Any A thru I Parity error
9 9
ns
C
tpHL 9.5 9_5 z
tpLH
Parity I/O Parity error
5 5
ns
<3:
tpHL
tpZH
6
5
6
5
en
..J
tpZL
XMIT Parity I/O
6 6
ns <3:
tpHZ 10 10
tpLZ 9.5 9.5

NOTE ·1: For load circuit and voltage waveforms. see page 1-12.
~83
TEXAS 2-283
INSTRUMENTS
POST OFFICE BOX 225012. DALLAS, TEXAS 75265
'AS286
A
B
C
0 PAR ERR ~----------~~----------- BYTE 1
E
F
G
H PAR I/O
XMIT
'AS286
A
B
C
0 PAR ERR ~--------~~r-------------BYTE2
E
F
G
H PAR I/O
I
XMIT
'AS286
A
B
C
o PARERR~---------4~r------------BYTE3
E
F
G
H PAR I/O
o--+---il
e - -....... XIVIIT
'AS286
A
B
C
0 PAR ERR ~----------~~-----------BYTE4
E
F
G
H PAR I/O
XMIT
EVEN/ODD --+--t----------------------'
FIGURE 1-32-BIT PARITY GENERATOR/CHECKER
Figure 1 shows [J 32-bit parity generator/checker with output polarity-switching, parity error detection, and parity on every byte.
128
2-284 TEXAS
INSTRUMENTS
'AS286
'AS286
PAR ERR
H
-======~
PAR I/O
'AS286
A
B
C
0 PAR ERR
H
'AS286
G
..
PAR I/O A
H
B
I
C
XMIT PARITY
0 PAR ERR
ERROR
E
F
G PARITY
'AS286 H PAR I/O I/O
A
B XMIT
en
H C
PAR ERR
!:::
'AS286
0
:::>
(J
A
B
H
G a::
C (J
0 PAR ERR I
E
F
H XMIT
en
G 'AS286 <t
H PAR I/O A
I
B
C
H XMIT C Z
'AS286
0 PAR ERR <t
E
A F en
B G ..oJ
C
H
I
PAR I/O
<t
0 PAR ERR
E H XMIT
F
G
H PAR I/O
I
H XMIT
XMIT
FIGURE 2-90-BIT PARITY GENERATOR/CHECKER WITH PARITY ERROR DETECTION
In Figure 2, a 90-bit parity generator/checker with the XMiT on the last stage is available for use with parity detection. I
!83
TEXAS 2-285
INSTRUMENTS
2-286
QUADRUPLE 2·INPUT MULTIPLEXER WITH STORAGE
• Selects One of Two 4·Bit Data Sources and SN54AS298 ... J PACKAGE
Stores Data Synchronously with System Clock SN74AS298 .•. N PACKAGE
(TOP VIEWI
• Applications:
Dual Source for Operands and Constants B2 VCC
in Arithmetic Processor; Can Release A2 OA
Processor Register Files for Acquiring Al OB
New Data B1 Oc
C2 00
Implements Separate Registers Capable
02 ClK
of Parallel Exchange of Contents, yet
01 WS
Retains External Load Capability
GNO C1
Has Universal·Type Register for
Implementing Various Shift Patterns; SN54AS298 ... FH PACKAGE
even Has Compound Left·Right Capability SN74AS298 ... FN PACKAGE
(TOP VIEWI
Reliability u
~~~~ot
description
This quadruple two·input multiplexer with Al OB
storage provides essentially the equivalent B1 Oc
functional capabilities of two separate MSI NC NC
functions (SN54AS157/SN74AS157 and C2 00
SN54AS175/SN74AS175) in a single 16·pin 02 ClK
package.
When the word-select (WS) input is low, Word 1 .-ou.-U)
°aZu~
(A 1, 81, C 1, 01 is applied to the flip-flops. A
high input to the word-select (WS) will cause the NC- No internal connection en
selection of Word 2 (A2, 82, C2, D2). The t:
selected word is clocked to the output terminals :::>
on the negative-going edge of the clock pulse. ua:
over the full military range of - 55 °C to 125 °C.
u
The SN74AS298 is characterized for operation en
from O°C to 70 0 e. «
c
z
FUNCTION TASLE
INPUTS OUTPUTS «
WORD
CLOCK OA Os Oc OD
en
~
SELECT
L ~ a1 bl c1 dl «
H .~ a2 b2 c2 d2
X H QAO QBO Qeo QDO
H = high level (steady state)
L = low level (steady state)
X = Irrelevant (any input. including transitions)
~ = transition from high to low level
a 1. a2, etc. = the level of steady-state input at AI. A2, etc.
0AO. 0BO. etc. = the level of 0A. 0B. etc. entered on the
most-recent ~ transition of 'the clock
input.
283 PRODUCT PREVIEW Copyright @ 1983 by Texas Instruments Incorporated

ThIa document contaIN Infonnetlon on • product under
ctav.lopmant. Taxa. I n _ t o r• ..."•• the right to TEXAS 2-287
changa or dlocOntinue thIa product without notice. INSTRUMENTS
POST OFFICE BOX 225012 a DALLAS. TEXAS 75265
logic symbol
IB
>
r- (141 aB
o
>
2
C
>
o
(131 ac
o
Si
o
c: (121 aD
=i
o
CLOCK~(1~11~______________~ ~________~
Pin numbers shown are for J and N packages..
128
2-288 TEXAS
INSTRUMENTS
Input voltage .............................................................. 7 V
Operating free-air temperature range: SN54AS298 ....................... - 55 °e to 125°e
SN74AS298 . . . . . . . . . . . . . . . . . . . . . . . . . . .. O°C to 70°C
Storage temperature range ......................................... - 65 °e to 150 0 e

SN54AS298 SN74AS298
UNIT
tw Pulse duration. ClK high or low ns
tsu Setup time before ClK ~ ns
th Hold time after ClK ./. ns

SN54AS298 SN74AS298
VIK VCC = 4.5 V. II = -18 mA -1 -1 V
VOH VCC = 4.5 V to 5.5 V. IOH = -2 mA Vee- 2 Vee- 2 V
VOL VCC = 4.5 V. IOl = 20 mA 0.35 0.5 0.35 0.5 V
II VCC = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH VCC = 5.5 V. VI = 2.7 V 20 20 p.A
III VCC = 5.5 V. VI = 0.4 V -0.5 -0.5 rnA
lot VCC = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
ICCH VCC = 5.5 V rnA
ICCl VCC = 5.5 V 23 23 rnA
t All typical values are at Vee = 5 V. TA = 25 De.

~The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS'

VCC = 4.5 v to 5.5 V.
Cl = 50 pF.
FROM TO Rl = 500 fl.
PARAMETER UNIT
SN54AS298 SN74AS298
f max MHz
tplH 6.5 6.5
ClK Q ns
tpHl 7 7
tAli typical values are at Vee = 5 V. TA = 25 De.

283
TEXAS 2-289
INSTRUMENTS
This versatile multiplexer/register can be connected to operate as a shift register that can shift N-places
in a single clock pulse.
The.following figure illustrates a BCD shift register that will shift a~ entire 4-bit BCD digit in one clock pulse.
PARALLEL lOAD
A
WORD
SELECT
CLOCK
'AS298
'AS298
b;:t 'AS298
I
MUX
~
~ MUX WS Gl
.,
MUX WS Gl
WS Gl ClK" C2
ClK"", C2
ClK,.,. C2 Al -,.
.-..:.:.:.. 1,20 DA
"'i
~1,20
Al ~1,2D DA A2 1,20
DA A2 1,20
A2 1,20 --.!!l DB
L-..-.!!.!. ---!!.. DB B2
DB B2
B2 --.-£!:. DC
----£!. Dc C2
L..---..£!. DC C2
C2
Dl
~ DD
DD D2
-...!!.!. DD D2
I
D2
I
--.- --.- ~
1
DIGITI DIGIT2 DIGIT3
When the word-select input is high and the registers are clocked, the contents of register 1 is transferred
(shifted) to register 2 and etc. In effect, the BCD digits are shifted one position. In addition, this application
retains a parallel-load capability which means that new BCD data can be entered in the entire register with
one clock pulse. This arrangement can be modified to perform the shifting of binary data for any number
of bit locations.
Another function that can be implemented with the' AS298 is a register that can be designed specifically
for supporting multiplier or division operations. The example below is a one-place/two-place shift register.
'AS298
MUX
WORD SELECT WS Gl
CLOCK ClK~ C2
Al~
A2 1,20
Bl 1,20
r--
1'O
B2 r--
'AS181A 1'1 Cl
OR g. t--
'~~t
Dl
{ f!2 IE... r--
F3
'AS298
~
WS Gl MUX
Cl~ C2
Al~
#~:~g
Bl
r--
l¥ -
Cl
ILg Dl
-
~ -
When word select is low and the register is clocked, the outputs of the arithmetic/logic units (ALU's) are
shifted one place. When word select is high and the registers are clocked, the data is shifted two places.
12E
2-290 TEXAS
INSTRUMENTS
POST oFFice BOX 225012 • DALLAS, TeXAS 75265
a·BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3·STATE OUTPUTS
02661. DECEMBER 1982-REVISED DECEMBER 19B3
• Multiplexed I/O Ports Provides Improved Bit SN54ALS·. SN54AS' ... J PACKAGE
Density SN74ALS', SN74AS' ... N PACKAGE
(TOP VIEW)
• Four Modes of Operation: Hold (Store), Shift
Right, Shift Left, and Load Data SO VCC
Gl S1
• Operates with Outputs Enabled or at High <32 Sl
Impedance G/QG QH'
• 3·State Outputs Drive Bus Lines Directly E/OE H/OH
C/OC 6 F/OF
• Can Be Cascaded for N·Bit Word Lengths A/OA D/OD
• 'ALS299 and AS299 Have Direct Overriding °A' S/OS
Clear ClR 9 ClK
GND SR
• ' ALS323 and AS323 Have Synchronous Clear
• Application: SN54ALS', SN54AS' •.. FH PACKAGE
Stacked or Push·Down Registers, Buffer SN74ALS', SN74AS' .•. FN PACKAGE
Storage, and Accumulator Registers (TOP VIEW)
u
Ceramic Chip Carriers in Addition to Plastic and
I~ It; g ~ U;
Ceramic DIPs
G/OG 4
E/OE
Reliability
C/OC
description A/OA
These eight-bit universal registers feature multiplexed °A'
110 ports to achieve full eight-bit data handling in a single
20-pin package. Two function-select inputs and two en
output-control inputs can be used to choose the modes
of operation listed in the function table. '=
~
Synchronous parallel loading is accomplished by taking both function-select lines SO and S1 high. This places the three- u
state outputs in a high-impedance state and permits data that is applied on the 1/0 ports to be clocked into the register. a:
Reading out of the register can be accomplished while the outputs are enabled in any mode. Clearing occurs asynchronously u
on 'AlS299, 'AS299 and synchronously on 'AlS323, 'AS323 when ClR is low. Taking either of the output controls,
en
G1 or G2, high disables the outputs but this has no effect on clearing, shifting, or storage of data.
<t
The SN54' family is characterized for operation over the full military range of -55°C to 125°C. The SN74' family is
C
characterized for operation from ooC to 70°C. 2
<t
en
..J
<t
TEXAS 2·291
INSfRUMENlS
TYPES SN54ALS299. SN54ALS323. SN54AS299. SN54AS323
SN74ALS299. SN74ALS323. SN74AS299. SN74AS323
8·BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3·STATE OUTPUTS
FUNCTION TABLE
INPUTS I/O PORTS OUTPUTS

OUTPUT
MODE
CLR S1 SO CONTROL CLK SL SR A/QA B/QB C/QC D/QD E/QE F/QF G/QG H/QH QA' QH'
G1 G2
Clear L X L L L X X X L L L L L L L L L L
('ALS299) L L X L L X X X L L L L L L L L L L
('AS299) L H H X X X X X X X X X X X X X L L
Clear L X L L L t X X L L L L L L L L L L
('ALS323) L L X L L t X X L L L L L L L L L L
('AS323) L H H X X t X X X X X X X X X X L L
H L L L L X X X QAO QSO QCO QDO QEO QFO QGO QHO QAO QHO
Hold
H X X L L L X X QAO QSO QCO QDO QEO QFO QGO QHO QAO QHO
H L H L L t X H H QAn QS n QCn QDn QEn QFn QGn H QGn
Shift Right
H L H L L t X L L QAn QS n QCn QDn QEn QFn QGn L QGn
H H L L L t H X QS n QCn QDn QEn QFn QGn QHn H QS n H
Shift Left
H H L L L t L X QS n QCn QDn QEn QFn QGn QHn L QS n L
Load H H H X X t X X a b c d e f 9 h a h
When one or both output controls are high the eight input/output termin~ls are disabled to the high-impedance state; however, sequential operation or clearing
of the register is not affected.
..
»
r-
m
logic symbols
'ALS299, 'AS299 'ALS323, 'AS323
»
:2
C
»
m
Q
:%I
("")
c:
=t
m
SL (181 2,4D
L..;.._ _ _- - '
2-292 TEXAS
INSTRUMENTS
8-BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3-STATE OUTPUTS
•ALS299 •• AS299
Sl (191
r++--++_---'-(1;,::81_ SHIFT LEFT
SERIAL INPUT
SHIFT RIGHT . . . , - - - - - - h
SERIAL INPUT (11) ,..,....~~,.u..;
FOUR
10ENTICAL
CHANNELS
NOT
SHOWN
ClK~(~12~1----~~H-~-+--H+~-4--H+~
ClR
OUTPUT {Gl
CONTROLS G2-(-31-----I 110 PORTS NOT SHOWN:
(61 CIOc (51 EIO E (161
BlOB (14101° 0 (151 FIO F GIOG HIO H
CD[
(9)
•ALS323 •• AS323
so ,",,(11~_-+--1r""\
Sl (19)
r+I--++_---:.;(1~8)_SHIFT lEFT
en
SERIAL INPUT !:::
(11) ::>
(.)
FOUR
IDENTICAL a:
CHANNELS
NOT (.)
SHOWN
en
ClK (121
c:t
C
(11) DH' 2:
c:t
OUTPUT
(21
Gl....:.:.~---d
en
-I
CONTROLS { G2-(~3)-----'
(7) (131 110 PORTS NOT SHOWN:
(6) CIOc (5) EIO E
(41
GI~
c:t
AIOA BiOs
(1 4101°0 (15) FIOF
Supply voltage, Vee .................................................................. 7 V
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
110 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS', SN54AS' .......................... - 55°C to 125°C
SN74ALS', SN74AS' .............................. ooe to 70°C
Storage temperature range ......................... '. . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C
33
TEXAS 2-293
INSTRUMENTS
B·BIT UNIVERSAL SHIFT/STORAGE REGISTERS WITH 3·STATE OUTPUTS
QA' or QW -0.4 -0.4
QA thru QH -1 -2.6
QA' or QW 4 8
10L Low-level output current mA
QA thru QH 12 24
fclock elock frequency (at 50% duty cycle) 0 25 0 30 MHz
eLK high or low 20 16.5
eLR low ('ALS299) 10 10
Select 25 20
Serial or I High level 18 16
tsu Setup time before eLK t

Parallel data J Low level 7 6
ns
eLR inactive (' ALS299) 15 15
eLR active (' ALS323) 25 20
eLR inactive (' ALS323) 18 16
Select 0 0
th Hold time after elK t ns
Serial or parallel data 0 0
TA Operating free-air temperature -55 125 0 70° °e
>
r0- PARAMETER TEST CONDITIONS
TYpt
UNIT
C/) MIN TYpt MAX MIN MAX
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
>
2
All outputs Vee = 4.5 V to 5.5 V, 10H = -0.4 mA vcc:- 2 vee- 2
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
C QA thru QH
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
>
C/)
QA' or Qw
Vee
Vee
=
=
4.5 V,
4.5 V,
IOL = 4 mA
10L = 8 mA
0.25 0.4 0.25
0.35
0.4
0.5
VOL V
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
Q QA thru QH
Vee = 4.5 V, 10L = 24 mA 0.35 0.5
::xJ A thru H Vee = 5.5 V, VI = 5.5 V 0.1 0.1
o II
Any other Vee = 5.5 V, VI = 7 V 0.1 0.1
mA
c IIH i Vee = 5.5 V, VI = 2.7 V 20 20 pA
=t
C/) IlL i
SO, Sl, SR, SL
Vee = 5.5 V, VI = 0.4 V
-0.2 -0.2
mA
QA" Qw -15 -70 -15 -70
lo§ Vee = 5.5 V, Vo = 2.25 V mA
QA thru QH -30 -112 -30 -112
J Outputs disabled 23 40 23 40

tFor 1/0 ports (OA through 0HI, the parameters IIH and IlL include the off-state output current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
12E
2-294 TEXAS
INSTRUMENTS
switching characteristics (see Note 1) .

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 500 Q,
FROM TO R2 = 500 Q,
PARAMETER UNIT
MIN MAX MIN MAX
f max 25 30 MHz
tpLH 4 15 4 13
CLK QA thru QH
tpHL 7 25 7 19
ns
tpLH 5 20 5 15
CLK QA' or QH'
tpHL 8 21 8 18
ern QA thru QH 6 29 6 22
ns
tpHL
('ALS299 only) QA' or QH' 6 29 6 22
tpZH 6 21 6 16
G1, G2 QA thru QH ns
tpZL 8 26 8 22
tpZH 7 21 7 17
SO, 51 QA thru QH ns
tpZL 8 26 8 22
tPHZ 1 10 1 8
tpLZ 5 23 5 15
tpHZ 1 16 1 12
SO, 51 QA thru QH ns
tPLZ 8 30 8 25
en
!:::
::J
(.)
a:
C3
en
<t
C
Z
<t
en
....I
<t
83
TEXAS 2-295
INSTRUMENTS

SN54AS299 SN74AS299
, QA' or QH' -2 -2
IOH High-level' output current rnA
QA thru QH -12 -15
QA' or QH' 20 20
QA thru QH 32 48
fclock Clock frequency (at 50% duty cycle) MHz
elK high or low
elR low (' AS299)
Select
Serial or I High level
tsu Setup time before eLK t
Parallel data I Low level ns
eLR inactive (' AS299)
elR active (' AS323)
elR inactive ('AS323)
Select
th Hold time after eLK t ns
Serial or parallel data
IfI electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
l>
r- SN54AS299 SN74AS299
(J) SN54AS323 SN74AS323
l> V,K Vee = 4.5 V, " = -18 rnA -1.2 -1.2 V
2 All outputs Vee = 4.5 V to 5.5 V, IOH = -2 rnA Vee- 2 Vee- 2
C Vee = 4.5 V, IOH = -12 rnA 2.4 3.2 V
VOH
QA thru QH
l> Vee = 4.5 V, IOH = -15 rnA 2.4 3.2
(J) QA' or QH' Vee = 4.5 V, IOL = 20 rnA 0.25 0.5 0.25 0.5
= 4.5 V,
~ 'OL = 32 rnA
VOL Vee 0.25 0.5 V
QA thru QH
Vee = 4.5 V, 'OL = 48 rnA 0.35 0.5
::JJ
n A thru H Vee = 5.5 V, V, = 5.5 V
rnA
c: "
Any other Vee = 5.5 V, V, = 7 V
=t
(J)
IIHt
',L t
Vee = 5.5 V,
Vee = 5.5 V,
V, = 2.7 V
V, = 0.4 V
pA
rnA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
I Outputs high
ICC Vee = 5.5 V I Outputs low rnA

tFor I/O ports lOA through 0HI, the parameters IIH and IlL include the off-state output current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS·
PRODUCT PREVIEW 128
2-296
ThIs page contains Intonnatlon on a product under
development. Tex.slnstruments ..serve. the right to
. TEXAS
POST OFFICE BOX 225012 e DALLAS. TEXAS 15265

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
FROM TO R1 = 5000,
PARAMETER UNIT
(lNPUTI (OUTPUT! R2 = 5000,
TA = MIN to MAX
SN54AS299 SN74AS299
SN54AS323 SN74AS323
f max MHz
tplH 10 10
ClK QA thru QH
tpHl 10 10
ns
tPlH 10 10
ClK QA' or QH'
tpHl 10 10
QA thru QH 12 12
tpHl ClR ns
QA' or QH' 12 12
tpZH 10 10
tpZl 10 10
tpZH 10 10
50,51 QA thru QH ns
tpZl 10 10
tpHZ 7 7
tpLZ 7 7
tpHZ 7 7
50,51 QA thru QH ns
tpLZ 7 7

en
!:::
:J
U
a:
U
en
«
c
2:
«
en
...J
«
33 PRODUCT PREVIEW
development. Texas Instruments reserves the right 10 TEXAS 2-297
..
l>
r-
en
l>
2
C
l>
en
Q
:u
o
c
=t
en
2-298
TYPES SN54ALS323, SN54AS323
SN74ALS323, SN74AS323
• Multiplexed 1/0 Ports Provides Improved Bit SN54ALS', SN54AS' ... J PACKAGE
Density SN74ALS', SN74AS' ... N PACKAGE
(TOP VIEW)
• Four Modes of Operation: Hold (Store). Shift
Right. Shift Left. and Load Data so VCC
<31 S1
• Operates with Outputs Enabled or at High G2 Sl
Impedance G/OG °H'
• 3·State Outputs Drive Bus Lines Directly E/OE H/OH
C/OC 6 F/OF
• Can Be Cascaded for N-Bit Word Lengths A/OA D/OD
• •ALS323 and' AS323 Have Synchronous Clear °A' S/OS
ClR 9 ClK
• Application: GND SR
Stacked or Push-Down Registers. Buffer
Storage. and Accumulator Registers
SN54ALS', SN54AS' . , , FH PACKAGE
• Package Options Include Both Plastic and SN74ALS', SN74AS' . " FN PACKAGE
Ceramic Chip Carriers in Addition to Plastic and (TOP VIEW)
Ceramic DIPs u
I~ 1(; ~ ~ U;
Reliability 3 2 1
G/OG 4 Sl
E/OE 5 °H'
C/OC 6 H/OH
A/OA F/OF
°A' D/OD
en
~
:::>
u
a:
For complete information on the SN54ALS323, SN54AS323, SN74ALS323, SN74AS323, see page
U
en
«
c
2:
«
en
..J
«
TEXAS 2-299
INSTRUMENTS
- »
r-
en
»
2
C
»
en
o
:D
o
c
=i
en
2-300
DUAL 4·LlNE TO 1·LlNE DATA SELECTORS/MULTIPLEXERS
SN54ALS352. SN54AS352 ... J PACKAGE

• Inverting Versions of ' ALS 153 and 'AS 153
• Permits Multiplexing from N Lines to 1 Line (TOP VIEW)
o Performs Parallel·to·Serial Conversion 1<3 VCC

o Strobe (Enable) Line Provided for Cascading (N Lines to B 2G
n Lines) 1C3 A
1C2 2C3
• Typical 'ALS352 Power per Multiplexer ... 16 mW 1 C1 2C2
• Typical 'AS352 Average Propagation Delay Times 1CO 2C1
Data Input to Output ... 2.7 ns 1Y 2CO
Strobe Input to Output ... 4.5 ns GND 2Y
Select Input to Output ... 4.5 ns
o Fully Compatible with Most TTL Circuits
• Package Options Include Both Plastic and Ceramic SN54ALS352.SN54AS352 ... FHPACKAGE
Chip Carriers in Addition to Plastic and Ceramic DIPs SN74ALS352. SN74AS352 ... FN PACKAGE
o Dependable Texas Instruments Quality and Reliability (TOP VIEW)
description
drivers to supply fully complementary binary decoding data
selection to the AND-DR-invert gates. Separate strobe inputs (G) A
are provided for each of the two four-line sections. 1C2 2C3
NC
operation over the full military temperature range of - 5 5 DC to 2C1
125 DC. The SN74ALS352 and SN74AS352 are characterized
CJ)
for operation from 0 DC to 70 DC.
>-OU>-O
'-ZZNU
!::
(!) N ::>
ua:
FUNCTION TABLE
SELECT U
DATA INPUTS STROBE OUTPUT logic symbol
INPUTS CJ)
B A CO Cl C2 C3 G Y <C
X X X X X X H H
L L L X X L H
C
X
2:
L L H L L
L H X
X
L
X
X
X
X L H
<C
10 CJ)
L H X H X X L L
lCO -oJ
H L L X L H
H L
X
X
X
X H X L L
lCl 1Y <C
lC2
H H X X X L L H
H H X X X H L L
2Y
2C2
2C3 (13)
TEXAS 2-301
INSTRUMENTS
TYPE SN54ALS352, SN54AS352, SN74ALS352, SN74AS352
1G
(6)
1CO
(5)
1C1 OUTPUT
1Y
DATA 1
(4)
1C2
(3)
1C3
SelECT,
~
(10)
2CO
l> (11)
r- 2C1
til DATA 2 OUTPUT
l> 2C2
(12) 2Y
2
C
(13)
l> 2C3
til
Q
lJ 20
n
c
==i Pin numbers shown are for J and N packages,
til
Supply voltage, Vee ...................................................' ........... 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS352, SN74AS352 . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 150 °e
2-302 TEXAS
INSTRUMENTS
TYPE SN54ALS352, SN74ALS352
DUAL 4·LlNE TO l·LlNE DATA SELECTORS/MULTIPLEXERS

UNIT
VIH High·level input voltage 2 2 V
IOH High·level output current -1 -2.6 rnA
VIK Vee = 4.5 V, II = -18mA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V, IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10L = 24 rnA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 /LA
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
lof Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V, See Note 1 6.5 10 6.5 10 rnA
C/)
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' !::
NOTE 1: lee is measured with data and select inputs at 4.5 V, and G inputs grounded. :::>
u
a:
switching characteristics (see Note 2) U
C/)
Vcc = 4.5 V to 5.5 V, <t
CL = 50 pF,
FROM TO RL = 500 n, C
PARAMETER
UNIT 2
<t
MIN MAX MIN MAX C/)
5 28 5 24
-I
tpLH
tpHL
A or B Y
5 24 5 21
ns <t
tpLH 3 21 3 18
Data (Any e) y ns
tpHL 2 15 2 13
tpLH 4 22 4 18
G Y ns
tpHL 4 24 4 20
TEXAS 2-303
INSTRUMENTS
TYPE SN54AS352, SN74AS352

SN54AS352 SN74AS352
UNIT
. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54AS352 SN74AS352
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = ~2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -12 rnA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 rnA 2.4 3.3
Vee = 4.5 V, 10L = 32 rnA 0.25 0.5
V
VOL
Vee = 4.5 V, 10L = 48 rnA 0.35 0.5
A, B 0.2 0.2
II
All others
Vee = 5.5 V, VI = 7 V
0.1 0.1
rnA
A,B 40 40
IIH
All others
Vee = 5.5 V, VI = 2.7 V p.A
20 20
A,B -1 -1
IlL
All others
Vee = 5.5 V, VI = 0.4 V
-0.5 -0.5
rnA
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
Vee = 5.5 V
I Outputs high 15.5 25 15.5 25
rnA
lee
I Outputs low 17.5 28 17.5 28
t All typical values are at Vee =: 5 V. T A = 25 De.


Vec = 4.5 V to 5.5 V,
Cl = 50 pF.
FROM TO Rl = 500 {I,
PARAMETER UNIT
(INPUT) (OUTPUTI TA = MIN to MAX
SN54AS352 SN74AS352
MIN MAX MIN MAX
tpLH 4 12.5 4 11
A or B Y ns
tpHL 4 14 4 13
tpLH 2 7.5 2 6.5
Data (Any e) y ns
tpHL 2 7 2 6
tPLH 3 8 3 7
G Y ns
tpHL 4 13.5 4 12
2-304 TEXAS
INSTRUMENTS
WITH 3-STATE OUTPUTS
02661, APRIL 1982 - REVISED DECEMBER 1983
SN54ALS353.SN54AS353 ••• JPACKAGE

• Inverting Versions of 'ALS253 and 'AS253 SN74ALS353. SN74AS353 ... N PACKAGE
• Permits Multiplexing from N Lines to 1 Line (TOPVIEWI
• Performs Parallel-to-Serial Conversion VCC

B 2<3
• Typical 'ALS353 Power per Multiplexer .•• 20 mW 1C3 A
• Fully Compatible with Most TTL Circuits 1C2 2C3
1 C1 2C2
• Package Options Include Both Plastic and Ceramic 1CO 2C1
1Y 2CO
• Dependable Texas Instruments Quality and Reliability GND 2Y
description
drivers to supply full binary decoding data selection to the AND- SN54ALS353. SN54AS353 ••. FH PACKAGE
OR-invert gates. Separate strobe inputs (<31 are provided for each SN74ALS353. SN74AS353 ... FN PACKAGE
of the two four-line sections. (TOPVIEWI
The three-state outputs can interface with and drive data lines of U
I(!) U UI(!)
bus-organized systems. With all but one of the common outputs m .... Z>N
disabled (at a high-impedance statel the low-impedance of the
single enabled output will drive the bus line to a high or low logic A
level. Each output has its own strobe (01. The output is disabled 2C3
when its strobe is high. NC
operation over the full military temperature range of - 55 DC to 2C1
125 DC. The SN74ALS353 and SN74AS353 are characterized
CJ)
for operation from 0 DC to 70 DC. >-OU>-O
..... ZZNU
(!) N t:
::::>
u
a::
u
CJ)
<t
logic symbol C
Z
FUNCTION TABLE <t
SELECT OUTPUT
DATA INPUTS OUTPUT B CJ)
INPUTS CONTROL
..J
Y
B
X
/It.
X
CO
X
Ct
X
C2
X
C3
X
G
H Z 1G
<t
L L L X X X L H lCO
L l H X X X l l
lCt 1V
l H X l X X l H
lC2
l H X H X X L l
lC3
H L X X l X l H
H l X X H X l l
H H X X X l l H
H H X X X H l l 2Y

~83
TEXAS 2-305
INSTRUMENTS
STROBE 1 G
ENABLE
1C1 J(~5)~____________~~~~
OUTPUT
DATA 1 1Y
SELECT
(11)
DATA 2 OUTPUT
2Y
STROBE 20 (15)
ENABLE
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ". . . . . . . . . . . . . . . . . 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . .\ . . . . . . . . . . . . . . . . . . . . . 5.5 V
SN74ALS353,SN74AS353 . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 °e
128:
2-306 TEXAS
INSTRUMENTS

UNIT
10H High-level output current -1 -2.6 rnA
PARAMETER -' TEST ~ONDITIONS UNIT
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. 10H = -0.4 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V. IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V. IOH =
-2.6 rnA 2.4 3.2
Vee = 4.5 V. IOl = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 24 rnA 0.35 0.5
10ZH Vee = 5.5 V. Vo = 2.7 V 20 20 p.A
10Zl Vee = 5.5 V. Vo = 0.4 V. -20 -20 p.A
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7V 20 20 p.A
III Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 rnA
lot Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
I disabled I All inputs. at 4.5 V 8 13 8 13
rnA
lee Vee ~ 5.5 V
I enabled I All inputs at Gnd 7 12 7 12
t All typical values are at Vee = 5 V. T A = 25 ae. .


Vee = 4.5 V to 5_5 V.
CL = 50 pF.
FROM TO
R1 = 500 n.
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 5 28 5 24
A or B Y ns
tpHL 5 24 5 21
tplH 4 21 4 18
Data (Any e) y ns
tpHL 3 15 3 13
tpZH 3 15 3 13
IT Y ns
tpZL' 3 19 2 16
tpHZ 2 12 2 10
IT Y ns
tplZ 2 16 2 14
NOTE 1: For load circuit and voltage waveforms, see page 1-12,
83
TEXAS 2-307
INSTRUMENTS

SN54AS353 SN74AS353
UNIT
SN54AS353 SN74AS353
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V. 10H = -12 rnA 2.4 3.2 V
Vee = 4.5 V. 10H = -15 rnA 2.4 3.3
Vee = 4.5 V. 10L = 32 rnA 0.25 0.5
VOL V
Vee = 4.5 V. IOL = 48 rnA 0.35 0.5
IOZH Vee = 5.5 V. Vo = 2.7V 50 50 p.A
IOZL Vee = 5.5 V. Vo = 0.4 V. -50 -50 p.A
A. B 0.2 0.2
All others 0.1 0.1
IIH
A. B
Vee = 5.5 V. VI = 2.7 V
40 - 40
p.A
All others 20 20
A. B -1 -1
IlL Vee = 5.5 V. VI = 0.4 V rnA
lOt Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V I Outputs low 19 31 19 31 rnA
t All typical values are at Vee = 5 V. TA = 25°e.


VCC = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS353 SN74AS353
MIN MAX MIN MAX
tpLH 3 10 3 9
AorB Y ns
tpHL 4 14 4 12
tpLH 3 8.5 3 7.5
Data (Any e) Y, ns
tpHL 2 6.5 2 6
tpZH 3 8.5 3 7.5
Strobe y ns
tpZL 4 12 4 11
tpHZ 2 6.5 2 5.5
Strobe y ns
tpLZ 3 9 3 7.5
128
2-308 TEXAS .
INSTRUMENTS
TYPES SN54ALS365 THRU SN54ALS368, SN74ALS365 THRU SN74ALS368
HEX BUS DRIVERS WITH 3·STATE OUTPUTS
• 3-State Outputs Drive Bus Lines Or Buffer Memory SN54ALS365. SN54ALS366 , •• J PACKAGE
Address Registers SN74ALS365. SN74ALS366 ••. N PACKAGE
(TOP VIEW)
• Choice of True or Inverting Outputs
<31 Vee
• Package Options Include Both Plastic and Ceramic A1 <32
Chip Carriers in Addition to Plastic and Ceramic DIPs Y1 A6
A2 Y6
Y2 A5
A3 Y5
, ALS365, , ALS367 True Outputs Y3 A4
, ALS366, , ALS368 Inverting Outputs GND Y4
description
SN54ALS365.SN54ALS366 ••• FHPACKAGE
These Hex buffers and line drivers are designed specifically to
SN74ALS365.SN74ALS366 ... FNPACKAGE
improve both the performance and density of three state memory
(TOP VIEW)
address drivers, clock drivers, and bus oriented rec~ivers and U
transmitters. The designer has a choice of selected combinations ~ Il; ~ ;;'I~
of inverting and non inverting outputs, symmetrical G (active-low
control) inputs. A6
Y1
These devices feature high fan-out. and improved fan-in. The A2 Y6
NC NC
SN74ALS365 through SN74ALS368 can be used to drive
Y2 A5
terminated lines down to 133 ohms. Y5
A3
stan'dard versions except that the recommended maximum IOL is
increased to 48 milliamperes. There are no -1 versions of the
SN54ALS' parts.
The SN54' family is characterized for operation over the full SN54ALS367. SN54ALS368 •.. J PACKAGE en
military temperature range of - 55 °C to 125 °C. The SN74' SN74ALS367. SN74ALS368 .•. N PACKAGE !::
family is characterized for operation from OOC to 70 0 C. (TOP VIEW) :::>
1G 1 U 16 Vee
ua:
1A1 2 15 2(3
1Y1
1A2 4
3 14
13
2A2
2Y2
u
en
1Y2 5
1A3 6
12
11
2A1
2Y1 «
1Y3 7
GND, [ 8
10 1A4
1Y4
c
9
2
«
SN54ALS367. SN54ALS368 ••• FH PACKAGE en
SN74ALS367. SN74ALS368 •.. FN PACKAGE -'
(TOP VIEW)
~ U
«
« I(!) U UI(!)
~~Z>N
3 2 1
1Y1 4 2A2
1A2 5 2Y2
Ne NC
1Y2 7 2A1
1A3 8 2Y1
9 1011 1213
C'lOU""",,,,"
>-ZZ>-«
~(!) ~ ~

83
ADVANCE INFORMATION
This document contains information on
TEXAS 2-309
a new product .. Specifications are subject INSTRUMENTS
to change without notice. POST OFFICE BOX 225012 • DALLAS, TEXAS 75265
logic symbols
'ALS365 'ALS366
(3)
Y1
(5)
Y2
(7)
Y3
(9)
Y4
(11)
Y5
(13)
Y6
'ALS367 'ALS368
1G
1A1 1Y1 1Y1

1A2 1Y2 1Y2
1A3 1Y3 1Y3
1A4 1Y4 1Y4
..
2G
2At 2Y1 2Y1

2A2 2Y2 2Y2
»
r- logic· diagrams (positive logic)
en
»
2
'ALS365 'ALS366 'ALS367 'ALS368
C
»
en
o
::c
o
c
=i
en
121
2-310 TEXAS
INSTRUMENlS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS365 thru SN54ALS368 . . . . . . . . . . . . . . . - 55°C to 125 DC
SN74ALS365 thru SN74ALS368 I • • • • • • • • • • • • • • • • • • • 0 DC to 70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50°C

THRU THRU
UNIT
12 24
48 t
TA Operating free-air temperature -55 125 0 70 dc::
The 48·mA limit applies for the SN74ALS365·1 thru SN74ALS368-1 only.
CI'J
THRU THRU
UNIT !::
MIN TYP+ MAX MIN TYP+ MAX
:J
(J
VIK Vee = 4.5 V, II
-18 rnA
Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA
=
Vee- 2
-1.5
Vee- 2
-1.5 V
a:
(J
Vee = 4.5 V, IOH = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, 10H = -12 rnA 2 CI'J
Vee = 4.5 V,
Vee = 4.5 V,
IOH = -15 rnA
IOL = 12mA 0.25 0.4
2
0.25 0.4
«
Vee = 4.5 V, IOL = 24 rnA V
C
VOL
0.5 :2
IOZH
(I0L = 48 rnA for - 1 versions)
Vee =' 5.5 V, Vo = 2.7 V 20
0.35
20 p.A
«
IOZL Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A CI'J
-I
II
IIH
Vee = 5.5 V,
Vee = 5.5 V,
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
rnA
p.A
«
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
Outputs high 7 7
'ALS365
Outputs low 12 12
'ALS367
Outputs disabled 13 13
ICC Vee = 5.5 V rnA
Outputs high 3 3
'ALS366
Outputs low 10 10
'ALS368
*AII typical values are at Vee = 5 V. TA = 25°e.

§The output conditions have b~en chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS.
283
TEXAS 2-311
INSTRUMENTS
, ALS365, , ALS367 switching characte~istics (see Note 1)

Vee = 4.S V to S.S V,
CL = SO pF,
Rl = SOO Q,
FROM TO R2 = SOO Q,
PARAMETER UNIT
SNS4ALS365 SN74ALS36S
tpLH 7 7
A Y ns
tpHL 7 7
tpZH y 14 14
G ns
tpZL 14 14
tpHZ y 5 5
G ns
tpLZ 8 8
, ALS366, , ALS368 switching characteristics (see Note 1)

Vee = 4.S v to 5.5 v,
eL = so pF,
R1 = SOD Q,
FROM TO R2 = SOD Q,
PARAMETER UNIT
tPLH 6 6
A Y ns
tpHL S 5
tpZH y 10 10
G ns
tpZL 17 17
tpHZ y 6 6
G ns
tPLZ 6 6

128:
2-312 TEXAS
INSTRUMENTS
OCTAL O·TYPE TRANSPARENT LATCHES WITH 3·ST"J1JnJTPUTS
02661. APRIL 1982-REVISEO DECEMBER 19B3
• 8 Latches in a Single Package SN54ALS373. SN54AS373. • J PACKAGE

SN74ALS373. SN74AS373. • N PACKAGE
• 3-State Bus-Driving True Outputs (TOP VIEW)
• Full Parallel Access for Loading OC VCC
• Buffered Control Inputs 10 80
1D 8D
• P-N-P Inputs Reduce D-C Loading on Data Lines 2D 7D
• Package Options Include Both Plastic and Ceramic 70
Chip Carriers in Addition to Plastic and Ceramic DIPs 60
6D
5D
50
description
C
These 8-bit latches feature three-state outputs designed
specifically for driving highly capacitive or relatively low-
SN54ALS373. SN54AS373 •• FH PACKAGE
impedance loads. They are particularly suitable for implementing
SN74ALS373. SN74AS373 .• FN PACKAGE
buffer registers, I/O ports, bidirectional bus drivers, and working
(TOP VIEW)
registers.
U
The eight latches of the' AlS373 and' AS373 are transparent Cd Iu Ud
...... 10> co
D-type latches. While the enable (C) is high the 0 outputs will
follow the data (D) inputs. When the enable is taken low, the 0
outputs will be latched at the levels that were set up at the D 2D SD
inputs. 20 7D
30 70
A buffered output-control input (OC) can be used to place the
eight outputs in either a normal logic state (high or low logic
levels) or a high-impedance state. In the high-impedance state
the outputs neither load nor drive the bus lines significantly. The
3D
4D
60
6D DIll
en
high-impedance third state and increased drive provide the !::
capability to drive the bus lines in a bus-organized system ~
without need for interface or pull-up components. u
The output control OC does not affect the internal operations of
ex:
the latches. Old data can be retained or new data can be entered u
while the outputs are off., en
The SN54AlS373 and SN54AS373 are characterized for «
operation over the full military temperature range of - 55°C to c
125°C. The SN74ALS373 and SN74AS373 are characterized 2
for operation from ooC to 70°C. «
en
-I
FUNCTION TABLE (EACH LATCH) «
INPUTS OUTPUT
OC ENABLE C 0 Q
L H H H
L H L L
L L X 00
H X X Z

83
TEXAS 2-313
INSTRUMENTS
OCTAL OoTYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS
logic symbol
10 10
20 20
3D 30
40 40
50 50
60 60
70 70
80 (19) 80

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Storage temperature rang .. .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e
7
128:
2-314 TEXAS
INsrRUMENTS
OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS

UNIT
tw Pulse duration, enable e high 10 10 ns
tsu Setup time, data before enable e. 10 10 ns
th Hold time, data after enable e. 7 7 ns
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -1 rnA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 rnA 2.4 3.2
Vee = 4.5 V, 10l = 12mA 0.25 0.4 0.25 0.4
V
VOL
Vee = 4.5 V, 10l = 24 rnA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
10Zl Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA en
IIH
III
Vee
Vee
= 5.5 V.
= 5.5 V.
VI = 2.7 V
VI = 0.4 V
20
-0.1
20
-0.1
p.A
rnA
t::
::l
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
U
I Outputs high 9 16 9 16 a:
ICC Vee = 5.5 V I Outputs low 16 25 16 25 rnA
U
t All typical values are at Vee = 5 V, TA = 25°e. en
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS. «
c
2!
«
en
-I
«
283
TEXAS 2-315
INSTRUMENTS
OCTAL O·TYPE TRANSPARENT LATCHES WITH 3·STATE OUTPUTS'

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tPLH 2 14 2 12
D Q ns
tpHL 4 19 4 16
tPLH 6 26 6 22
C Any Q ns
tpHL 7 27 7 23
tpZH 5 24 5 20
OC Any Q ns
tPZL 6 22 6 18
tpHZ 2 16 2 12
OC Any Q ns
tPLZ 2 12 2 10
-=-
~
0 latch signal conventions
It is TI practice to name the outputs and other inputs of a D·type latch and to draw its logic symbol based on the
assumption of true data (D) inputs. Then outputs that produce data in phase with the data inputs are called Q and those
l> producing complementary data are called Q. An input that causes a Q output to go high or a Q output to go low is called
r- Preset; an input that causes a Q output to go high or a Q output to go low is called Clear. Bars are used over these pin
fJ)
l> In some applications it may be advantageous to redesignate the data input D. In that case all the other inputs and
2 outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
C pin numbers are shown in parentheses.
l>
fJ)
Q PRE S (5) Q CLR R (5)

::IJ Q
o C C1 C C1
c D 1D (6) a 0 1D
Q
=i
fJ)
CLR R PRE S
Notice that Q and '0 exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (t::..) on PRE and CLR remain since these inputs are still active·low. but that the presence or absence of the
polarity indicator changes at D. Q. and Q. Of course pin 5 ('0) is still in phase with the data input D. but now both are
considered active· low .
128
2-316 TEXAS
INSTRUMENTS
, OCTAL O·TYPE TRANSPARENT LATCHES WITH 3·STATE OUTPUTS

SN54AS373 SN74AS373
UNIT
Vee Supply voltage 4,5 5 5,5 4,5 5 5.5 V
10H High-level output current -12 -15
tw Pulse duration, enable e high 5.5 4.5 ns
tsu Setup time, data before enable e,j. 2 2 ns
th Hold time, data after enable e,j. 3 3 ns
TA Operating free-air temperature -55 125 0 70 !"e
electrical characteristics over recommended operating free-air temperature range (unless otherwise .noted)
SN54AS373 SN74AS373
-18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = -2mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -12 rnA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 rnA 2.4 3.3
Vee = 4.5 V, 10l = 32 rnA 0.27 0.5
V
VOL
Vee = 4.5 V, 10l = 48 rnA 0.32 0.5
10ZH Vee = 5.5 V, Vo = 2.7V 50 50 p.A
10Zl Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA en
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A t:::
III Vee = 5.5 V, VI = 0.4 V -0.02 -0.5 -0.02 -0.5 rnA ::l
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA U
I Outputs high 55 90 55 90 a::
lee Vee = 5.5 V IOutputs low 55 85 55 85 rnA C3
en
tAli tYPical values are at Vee = 5 V, TA = 25°e.
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' «
c
z
«
en
..oJ
«
33
TEXAS 2-317
INSlRUMENlS
OCTAL D·TYPE TRANSPARENT LATCHES WITH 3·STATE OUTPUTS
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
FROM TO R1 = 500 n,
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 n,
TA = MIN to MAX
SN54AS373 SN74AS373
MIN MAX MIN MAX
tPLH 3.5 8 3.5 6
D Q ns
tpHL 3.5 7 3.5 6
tpLH 6.5 14 6.5 11.5
C Any Q ns
tpHL 5 8 5 7.5
tpZH 2 7.5 2 6.5
OC Any Q ns
tpZL 4.5 10.5 4.5 9.5
tpHZ 3 7.5 3 6.5
OC Any Q ns
tPLZ 3 8 3 7
NOTE 1: For load circuits and voltage waveforms, see page 1·12.
lEI
l>
r-
en
l>
z
C
l>
en
Q
:u
o
c:
=i
en
12S
2-318 TEXAS
INSTRUMENTS
POST OFFICe BOX 225012 • DALLAS. TeXAS 75265
OCTAL D·TYPE EDGE·TRIGGERED FLlp·FLOPS
• D·Type Flip-Flops In a Single Package SN54AlS374.SN54AS374. J PACKAGE

SN74AlS374.SN74AS374. N PACKAGE
• 3-State Bus-Driving True Outputs (TOP VIEW)
• Full Parallel Access for Loading
oe Vee
• Buffered Control Inputs 1Q 8Q
1D 8D
• Package Options Include Both Plastic and Ceramic 2D 7D
Chip Carriers in Addition to Plastic and Ceramic DIPs 2Q 7Q
• Dependable Texas Instruments Quality and Reliability 3Q 6Q
3D 6D
4D 5D
4Q 5Q
description GND elK
These 8-bit flip-flops feature three-state outputs designed
specifically for driving highly capacitive or relatively low-
impedance loads. They are particularly suitable for implementing SN54AlS374.SN54AS374. FH PACKAGE
buffer registers. I/O ports, bidirectional bus drivers, and working SN74AlS374.SN74AS374. FN PACKAGE
registers. (TQPVIEW)
The eight flip-flops of the 'ALS374 and 'AS374 are edge- u
o diu ud
........ 0>00
triggered D-type flip-flops. On the positive transition of the clock
the Q outputs will be set to the logic levels that were set up at the 3 2 1 2019
D inputs.
2D 4 8D
A buffered output-control input can be used to place the eight 2Q 5 7D
outputs in either a normal logic state (high or low logic levels) or a 3Q 6 7Q
high-impedance state. In the high-impedance state the outputs 3D 7 6Q
neither load nor drive the bus lines significantly. The high- 4D 8 6D
impedance third state and increased drive provide the capability en
to drive the bus lines in a bus-organized system without need for !:::
interface or pull-up components. ~
(.)
The output control (DC) does not affect the internal operation of a:
the flip-flops. Old data can be retained or new data can be
(.)
entered while the outputs are in the high-impedance state.
FUNCTION TABLE (EACH FLIP-FLOP)
en
operation over the full military temperature range of - 55°C to ~
INPUTS
ClK D
OUTPUT
a
«
125°C. The SN74ALS374 and SN74AS374 are characterized L t H H c
for operation from ooe to 70°C. z
L
L
t
L
L
X
L
00 «
H X X Z en
-I
«
~83
TEXAS 2-319
INSfRUMENTS
logic symbol
141
20----+-1
III 171
30-----+--1
l>
r- 40.:....18..:..1_ _~
en
l>
z 1131
50---+---1
C
l>
en 60
1141
(")
:0
(")
11.:....:7..:.1_-+-1
70.:..
c:
=i 1181
en 80--..:..-----1

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Storage temperature range . . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e
128
2-320 TEXAS
INSTRUMENTS
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS

UNIT
IOH high-level output current -1 -2.6 rnA
Pulse duration
I eLK high 16.5 14
ns
tw
lelK low 16.5 14
tsu Setup time. data before eLK! 10 10 ns
th Hold time. data after eLK! 4 0 ns
VIK Vee =
4.5 V. II = -18 rnA -1.5 -1.5 V
..
Vee =
4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2
VOH Vee - 4.5 V. IOH - -1 rnA 2.4 3.3 V
Vee = 4.5 V. IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V. IOL = 12mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V IOl = 24 rnA 0.35 0.5
10ZH Vee = 5.5 V. Vo = 2.7 V 20 20 p.A
10ZL Vee - 5.5 V. VI = 0.4 V -20 -20 p.A en
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA !::
IIH Vee = 5.5 V. VI - 2.7 V 20 20 p.A ::J
III Vee = 5.5 V. VI= 0.4 V -0.2 -0.2 rnA (J
10; Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA a:
I Outputs high 11 19 11 19 (J
en
<C
tAli tYPical values are at Vee = 5 V. TA = 25°e.
tThe output conditions have been chosen to produce a current that closely approximates o(le half of the true short-circuit output current. lOS. C
2:
<C
en
..oJ
<C
283
TEXAS 2-321
INSTRUMENTS

VCC ';' 4.5 V to 5.5 V,
CL = 50 pF,
FROM TO R1 = 5000,
PARAMETER UNIT
(lNPUTI (OUTPUT! R2 = 5000,
TA = MIN to MAX
MIN MAX MIN MAX
f max 30 35 MHz
tPLH 3 15 3 12
eLK Q ns
tpHL 5 18 5 16
tpZH 5 19 5 17
6C Q
7 18
ns
tPZL 20 7
2 12 2 10
tpHZ
tpLZ
oc Q
3 24 3 18
ns

EXPANDABLE 4-WORD BY 8-BIT GENERAL REGISTER FILE
4
'ALS374
OR'AS374
-.J
l>
r-
en
l>
2
'ALS139
C OUTPUT
l>
en
ENABLE
SELECT
{
Q INPUT
:a
(") CLOCK
SELECT
{
C
~
en CLOCK"\r
8 8
INPUT OUTPUT
128:
2-322 TEXAS
INSTRUMENlS
POST OFFICE BOX 225012 • DALLAS: TEXAS 75265

SN54AS374 SN74AS374
UNIT
tw Pulse duration
I elK high 5.5 4
ns
I elK low 5 3
Setup time data
tsu 3 2 ns
before elKI
th Hold time, data after elK I 3 2 ns
SN54AS374 SN74AS374
VIK Vee =
4.5 V, II = -18 mA -1.2 -1.2 V
Vee =
4.5 V to 5.5 V, 10H = -2 mA Vee- 2 Vee- 2
VOH Vee - 4.5 V, 10H - -12 mA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 mA 2.4 3.3
Vee = 4.5 V, 10l = 32 mA 0.29 0.5
VOL V
Vee = 4.5 V 10l = 48 mA 0.34 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A en
10Zl Vee = 5.5 V, VI = 0.4 V -50 -50 p.A !:::
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA ::>
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A u
III
l oe, elK
Vee = 5.5 V, VI = 0.4 V
-0.5 -0.5
mA
a:
10:1:
I Data
Vee = 5.5 V, Vo = 2.25 V -30
-3
-112
\
-30
-2
-112 mA
u
I en
lee Vee = 5.5 V I
Outputs high
Outputs low
77
84
120
128
77
84
120
128 mA «
I Outputs disabled 84 128 84 128 c
tAli typical values are at Vee = 5 V. TA = 25°e. 2
:f:The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
«
en
..J
«
283
TEXAS 2-323
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
CL = 50 pI",
FROM TO R1 = 500 ()
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 ()
TA = MIN to MAX
SN54AS374 SN74AS374
MIN MAX MIN MAX
. f max 100 125 MHz
. tpLH 3 11 3 8
elK Q ns
tPHl 4 11.5 4 9
tpZH 2 7 2 6
6C Q ns
tpZl 3 11 3 10
tpHZ 2 7 2 6
Dc Q ns
tplZ 2 7 2 6

BIDIRECTIONAL BUS DRIVER
OUTPUT
CONTROL 1 L-i 'ALS374
~'ASJ74
EN
-.J CLOCK 1
t'
~1
1D I> 'V
l>
r-
CA
BIDIRECTIONAL BIDIRECTIONAL
.~ DATA BUS 1 DATA BUS 2
C
l> ....
CA 'ALS374
n OUTPUT
CONTROL 2
or 'AS374
EN
::IJ
n C1
c: CLOCK 2
~ 4- 'V <J 1D f-+-

tJ)
-=:::...... -......
1=...
~
~
..: ...
...... -
BUS CLOCK 1 H~ L.r
EXCHANGE LI
CLOCK CLOCK 2 H Lr
CLOCK CIRCUIT FOR BUS EXCHANGE
128,
2·324 TEXAS
INSTRUMENTS
POST OFFiCe BOX 225012 • DALLAS. TexAS 75265
4·BIT CASCADABLE SHIFT REGISTERS WITH 3·STATE DUTPUTS
• Cascadable, 4·Bit, Three·State Parallel-to- SN54AS395 ... J PACKAGE

Serial,Serial-to-Parallel Conversations SN74AS395 ... N PACKAGE
(TOP VIEW)
o Parallel Synchronous Loading
ClR VCC
o Direct Overriding Clear
SER OA
• Applications: A Os
N-Bit Serial·to-Parallel Converter S Oc
N-Bit Parallel-to-Serial Converter C OD
N-Bit Storage Register D OD'
LD/SH ClK
o Dependable Texas Instruments Quality and
GND DC
Reliability
description
These 4-bit registers feature parallel inputs, (TOP VIEW)
parallel outputs, cascadable output, and clock,
serial load/shift, output control, and direct ffi 15
Uluz>d
U ~ <{
overriding clear inputs,

Shifting is accomplished when the load/shift
A Os
control is low. Parallel loading is accomplished
S Oc
by applying the four bits of data and taking the
NC NC
load/shift control input high. The data are loaded
C OD
into the associated flip-flops and appear at the
o OD'
outputs after the high-to-Iow transition of the
clock input. During parallel loading, the entry of
serial data is inhibited. IUlZZOd
I 0 UIU:':::
0<.:)
When the output control is low, the normal logic ....J en
levels of the four outputs are available for driving NC - No iniei;nal connection
!::::
the loads or bus lines. The outputs are disabled :)
independently of the level of the clock by a U
high logic level at the output control input. The outputs then present a high impedance and neither load 0:
nor drive the bus line; however, sequential operation of the registers is not affected. During the high- U
impedance mode, the output at QD' is still available for cascading.
en
The SN54AS395 is characterized for operation over the full military range of - 55°C to 125°C. The «
SN74AS395 is characterized for operation from DoC to 70°C.
c
z
FUNCTION TABLE «
en
...I
INPUTS 3-STATE OUTPUTS CASCADE
CLEAR
LOAD/SHIFT
CONTROL
CLOCK SERIAL
A
PARALLEL
B B B
OA ,OB Oc °D
OUTPUT «'
GD'
L X X X X X X X L L L L L
H H H X X X X X °AO °BO OCO ODO ODO
H H .j, X a b c d a b c d d
H L H X X X X X OAO °BO OCO ODO ODO
H L .j, H X X X X H OAn °Bn OCn OCn
H L .j, L X X X X L OAn OBn OCn OCn
When the output control is high, the 3-state outputs are disabled to the high-impedance state; however, sequential operation of the registers
and the output at GO' are not affected.

change or discontinue this piOduct without notice. INSTRUMENTS
4·BIT CASCADABLE SHIFT REGISTERS WITH 3·STATES OUTPUTS
logic symbol
SRG4
aB
ac
aD
aD,
_ logic diagram (positive logic)
,...l> .
DATA INPUTS
tA A B C o
l> (3) (4) (5) (6)
:2
o
l>
tA
(')
:ii
(') CLOCK~(1~O)__~~~______-+__~______~__~+-______+-~
c
=t
~
OUTPUT (91
CONTROL (15) (14) (13) (121 (11)
,O'
A 0B Oc ad,
Ii
AD'
3-STATE OUTPUTS
CASCADE
OUTPUT
1283
2-326 TEXAS
INSTRUMENTS
TYPES SN54ALS465A THRU SN54ALS468A. SN74ALS465A THRU SN74ALS468A
OCTAL BUFFERS WITH 3·STATE OUTPUTS
02661, APRIL 1982 - REVISED DECEM8ER 1983
• Mechanically and Functionally Interchangeable with SN54ALS465A, SN54ALS466A ... J PACKAGE

DM71/81LS97 and DM71/81LS98 SN74ALS465A, SN74ALS466A ... N PACKAGE
(TOP VIEW)
• P·N·P Inputs Reduce Bus Loading
(31 Vee
• 3·State Outputs Rated at IOL of 12 rnA and 24 rnA for (32
A1
SN54ALS' and SN74ALS', Respectively
Y1 AB
• Package Options Include Both Plastic and Ceramic A2 YB
Chip Carriers in Addition to Plastic and Ceramic DIPs Y2 A7
A3 Y7
• Dependable Texas Instruments Quality and Reliability A6
Y3
A4 Y6
DEVICE DATA PATH
Y4 A5
'ALS465A True
GND Y5
'ALS466A Inverting
'ALS467A True
'ALS468A Inverting SN54ALS465A, SN54ALS466A ... FH PACKAGE
SN74ALS465A, SN74ALS466A . , .FN PACKAGE
U
These octal buffers utilize the latest advanced low-power Schottky ......... UN
technology. The 'ALS465A and 'ALS466A have a two-input >- ~I<':) >1<,:)
active-low AND enable gate controlling all eight data buffers. The 3 2 1 2019
'ALS467A and 'ALS46BA have two separate active-low enable A2 AB
inputs each controlling four data buffers. In each case, a high level Y2 YB
on any G places the affected outputs at high impedance. A3 A7
Y3 Y7
The SN54ALS465A, SN54ALS466A, SN54ALS467A, and
A4 A6
SN54ALS46BA are characterized for operation over the full
military temperature range of - 55 °e to 125°e. The 9 10 11 1213
en
SN74ALS465A, SN74ALS466A, SN74ALS467A, and
SN74ALS46BA are characterized for operation from ooe to 70 oe.
!::
:::J
U
a:
C3
SN54ALS467A, SN54ALS468A ... J PACKAGE SN54ALS467A, SN54ALS468A ... FH PACKAGE
en
SN74ALS467A, SN74ALS468A ... N PACKAGE
(TOP VIEW)
SN74ALS467A, SN74ALS468A ... FN PACKAGE
(TOP VIEW)
«
...... U c
113
1A1
Vee
2(3
>- ~I<.:) UI<':)
......... >N z
1Y1 2A4
<t
1A2 2Y4 1A2 2A4 en
..J
1Y2
1A3
2A3
2Y3
1Y2
1A3
2Y4
2A3 «
1Y3 2A2 1Y3 2Y3
1A4 2Y2 1A4 2A2
1Y4 2A1
GND 2Y1
TEXAS 2-327
INSTRUMENTS
POST oFFice BOX 225012 • DALLAS, TeXAS 75265
TYPES SN54ALS465A THRU SN54ALS468A, SN74ALS465A THRU SN74ALS468A
logic svmbols
'ALS465A 'ALS466A
V1
V2
V3
V4
'ALS465A 'ALS466A
G1 01
1111 (12
A1 (3)
V1
(12
A1
(3)
V1
»
r- A2 (5)
V2 A2
(5)
V2
VJ
»
:2
A3
171
V3 A3
(7)
V3
(91 (9)
C A4 V4 A4 V4
»
VJ
AS
(11)
V5 AS
(11)
V5
(13) (13)
Q A6 V6 A6 V6
:J:J (151 (151

(') A7 V7 A7 V7
c: (17) (17)
=i AB VB AB VB
VJ
1283
2-328 TEXAS
INSTRUMENTS
POST OFFICE 80X 225012 • DALLAS, TEXAS 75265
logic symbols
'ALS467A 'ALS468A
1Y1 1Y1
1Y2 1Y2
1Y3 1Y3
1Y4 1Y4
'ALS467A 'ALS468~
1A1 1A1 >0_+-"",(3..:..1 1 Y1
1A2 >-----li----.!.:(5:.!..1 1 Y 2 1A2 >O-----I-..!.:(5:.:...1 1 Y 2

(fJ
1A3 >---tr--'-"(7~1 1 Y3 1A3 >O---I~(7..;...1 1 Y3 !:::
> __.:.:;(9.;..1 1Y4
::>
1A4 1A4 >o-_-..!.:(9:.:...1 1 Y4 (.)
a:
<:)
(fJ
1111 2Y1 >o_-t-'-'1.;.,.1;.:.1 2Y1
<t
C
______- " >-----I....!'~13~1 2Y2 2A2 .J>(>--t.-;'..;..;13;..:...1 2Y2 Z
(151 2Y3
<t
2A3 >0_-+-,-'1.:..,;:5;.:,.1 2Y3
(fJ
17
-'
_ _---, >-_--=-'1.:..,;:7.!.1 2Y4 2A4 >o-_....:':.:.. 1 2Y4
:..L <C
1283
TEXAS 2-329
INSTRUMENTS
Input voltage ........................................... : . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS465A THRU SN54ALS468A . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS465A THRU SN74ALS468A ................. ooe to 70°C

THRU THRU
UNIT
12 24
4St
tThe extended limit applies only if Vee is maintained between 4.75 V and 5.25 V.
The 48 mA limit applies for SN74ALS465A-1, SN74ALS466A-1, SN74ALS467A-1, and SN74ALS468A·1 only.
~ eleCUleal charac...istics over recommended operating free-air temperature range (unless otherwise noted)
SN54ALS465A SN74AlS465A
THRU THRU
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 mA vee- 2 vee- 2
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, 10H = -12 mA 2
Vee = 4.5 V, 10H = -15 mA 2
Vee = 4.5 V, 10l = 12 mA 0.25 0.4 0.25 0.4
VOL Vee = 4.5 V, 10l = 24 mA V
0.35 0.5
(lOl = 48 mA for- 1 versions)
10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
10ZL Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 p.A
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
'AlS465A
Vee = 5.5 V Outputs low 19 33 19 28 mA
'ALS467A
lee
'AlS466A
Vee"; 5.5 V Outputs low 16 29 16 24 mA
'AlS468A
tAli typical values are at Vee = 5 v, TA = 25°e.

1283
2-330 TEXAS
INSfRUMENTS
'ALS465A, 'ALS467 A switching characteristics (see Note 1 I
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
PARAMETER
FROM TO Rl = 500 n.
UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 16 2 13
A Y ns
tPHL 4 15 4 12
tpZH 4 27 4 23
IT Any Y ns
tpZL 5 30 5 25
tpHZ 2 12 2 10
IT Any Y ns
tpLZ 3 21 3 18
'ALS466A. 'ALS468A switching characteristics (see Note 1 I.

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
FROM TO R1 = 500 n.
UNIT
(INPUT) (OUTPUT) R2 = 500 O.
TA = MIN to MAX
SN 54ALS468A SN74ALS468A
MIN MAX MIN MAX
tpLH 3 14 3 12
tpHL
A Y
2 11 2 9
ns en
tpZH
G Any Y
4 21 4 16
ns
!::
tpZL 7 25 7 23 ::J
tpHZ 2 12 2 10
()
tpLZ
G Any Y
2 20 2 17
ns a:
()
NOTE 1: For load circuit and voltage waveforms. see page 1-12_
en
«
c
2:
«
en
-J
«
1283
TEXAS 2-331
INSTRUMENTS
IIIIfJ
l>
r-
C/)
l>
:2
C
l>
C/)
-
(')
:a
(')
c:
=i
en
2-332
8·BIT IDENTITY COMPARATORS
02661, JUNE 1982-REVISED DECEMBER 1983
• Compares Two 8·Bit Words SN54ALS' , .• J PACKAGE

SN74ALS' .• , N PACKAGE
• Choice of Totem-Pole or Open-Collector Outputs
ITOPVIEW)
• 'ALS518, 'ALS520, and 'ALS522 Have 20-kQ Pull-up
Resistors on Q Inputs G VCC
PO P=Q/P=Qt
• Package Options Include Both Plastic and Ceramic QO Q7
Chip Carriers in Addition to Plastic and Ceramic DIPs P1 P7
Q1 Q6
P2 P6
INPUT OUTPUT FUNCTION
Q2 Q5
TYPE PULL-UP AND P3 P5
RESISTOR CONFIGURATION Q3 Q4
'ALS518 Yes P = Q open-collector GND P4
'ALS519 No P = Q open-collector
SN54ALS' . • • FH PACKAGE
'ALS520 Yes P=CI totem-pole
SN74ALS' ••• FN PACKAGE
'ALS521 t No P = Q totem-pole
ITOPVIEW)
'ALS522 Yes p;;;Q open-collector
t'ALS521 is identical to 'ALS688
description
These identity comparators perfrom comparisons on tw'o eight-
bit binary or BCD words, The' ALS518 and' ALS51 9 provide
P=Q outputs, while the 'ALS520, 'ALS521, and 'ALS522 P1 07
provide P=Q outputs, The 'ALS518, 'ALS519, and 'ALS522 Q1
have open-collector outputs. The 'ALS518, 'ALS520, and
'ALS522 feature 20-kQ pull-up termination resistors on the Q
inputs for analog or switch data.
P2
Q2
P3 14
P7
06
P6
05
III
en
The SN54ALS51.8 through SN54ALS522 are characterized for 9 1011 1213 !::
operation over the full military temperature range of - 55 °C to C"lOvvL!'l
~
" 125°C. The SN74ALS518 through SN74ALS522 are
Oza..Oa..
l!)
U
characterized for operation from 0 °c to 70°C,
£X:
tP=Q for 'ALS518 and 'ALS519, and p,;;Q for
'ALS520, 'ALS521, and 'ALS522.
U
en
<C
C
Z
<C
en
...J
FUNCTION TABLE <C
INPUTS OUTPUTS
DATA ENABLE
P=Q P=Q
p, Q G
P=Q L H L
P>Q L L H
P<Q L L H
X H L H

1283
TEXAS 2-333
INSTRUMENTS
logic symbols
'ALS518 'ALS520 'ALS522

'ALS519 'ALS521
COMP COMP COMP
G (1) I> G I> G I>
PO (2) PO PO
} }
(4)
l
P1 P1 P1
(6)
P2 P2 P2
(8)
P3 P3 P3
(11) (11)
P4 P4 P4
(13) (13)
PS PS PS
(1S)
P6 (1S) P6 P6
(17) (19) F-Q (19) p;Q
P7 (17) 1P=0 <) (19) P=O P7 1P=0 P7 1P=0 0
00 (3) (3) 00 (3)
00
} } }
01 (S) 01 (5) 01 (S)
02 171 02 (7) 02 171
OJ (9) OJ (9) 03 (9)
04 (12) 04 (12) 04 (12)
05 (14) OS (14) os (14)
06 (16) 06 (16) 06 (16)
07 (18) 07 (18) 07 (18)

'ALS518 'ALSS20
'ALS519 'ALSS21
'ALSS22
P7 P7
07 07
P6 P6
06 06
PS PS
OS os
P4 P4
04 04
)--..:.;(1~9),-- P=O
P3 P3
OJ OJ
P2 P2
02 02
P1 P1
01 01
PO PO
00 00
1283
2-334 TEXAS
INSTRUMENTS
TYPES SN54ALS518 THRU SN54ALS522. SN74ALS518 THRU SN74ALS522
Input voltage: Q inputs of' ALS51 B.' ALS522 . . . . . . . . . . . . . . . . . . . . Vee + 0.5 V or 5.5 V. whichever is less
All other inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . 7 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS51 B. SN54ALS519. SN54ALS522 ....... - 55°C to 125 °e .
SN74ALS51B.SN74ALS519.SN74ALS522 ........... OOet070oe
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150 °e

UNIT
VOH High-level output voltage' 5.5 5.5 V
CJ)
!::
SN54ALS518 SN74ALS518 :J
PARAMETER
SN54ALS519 SN74ALS519 U
TEST CONDITIONS
UNIT
a=
MIN TYpt MAX MIN Typt MAX U
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
CJ)
IOH Vee = 4.5 V,
Vee = 4.5 V,
VOH = 5.5 V
IOL = 12 mA 0.25
0.1
0.4 0.25
0.1
0.4
mA
«
VOL
Vee = 4.5 V, IOL = 24 mA 0.35 0.5
V
c
'ALS518, 'ALS522 Q inputs Vee = 5.5 V, VI = 5.5 V 0.1 0.1 z
II
All other inputs
'ALS518, 'ALS522 Q inputs
Vee = 5.5 V, VI = 7 V 0.1
-0.2
0.1
-0.2
mA
mA
«
IIH Vee =5.5 V, VI = 2.7V CJ)
All other inputs 20 20 /J A ...I
IlL
'ALS518, 'ALS522 Q inputs
All other inputs
Vee = 5.5 V, VI = 0.4 V
-0.6
-0.1
-0.6
-0.1
mA «
'ALS518 11 17 11 17
lee 'ALS519 Vee = 5.5 V, See Note 1 11 17 11 17 mA
'ALS522 11 17 11 17
tAli typical values are at Vee = 5 v,

TA = 25°e.
NOTE 1: lee is measured with Ggrounded, P and a at 4.5 V.
283
TEXAS 2-335
INSTRUMENTS
TYPES SN54ALS518, THRU SN54ALS522, SN74ALS518 THRU,SN74ALS522
'AlS518, 'AlS519 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 680 Q.
FROM TO
(INPUT) (OUTPUT)
MIN MAX MIN MAX
tpLH 15- 37 15 33
P or Q P=Q ns
tpHL 3 18 3 15
tPLH 15 37 15 33
G P=Q ns
tPHL 3 18 3 15
, AlS522 switching characteristics (see Note 1)

Vcc =4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 680 Q.
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 10 30 10 25
Por Q P=Q ns
tpHL 5 25 5 23
tPLH 8 30 8 25
G P=Q ns
tPHL 8 30 8 23
1283
2-336 TEXAS
INSTRUMENlS
TYPES SN54ALS518, THRU SN54ALS522, SN74ALS518 THRU SN74ALS522
8-BIT IDENTITY COMPARATORS
Input voltage: Q inputs of' ALS520 . . . . . . . . . . . . . . . . . . . . . . . . . . . Vee + 0.5 V or 5.5 V, whichever is less
All other inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS520, SN54ALS521 . . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74ALS520,SN74ALS521 . . . . . . . . . . . . . . . . . . . . . . OOet070oe
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150 °e

TA Operating free-air temperature. -55 125 0 70 °e

SN54ALS521 SN74ALS521 UNIT en
MIN Typt MIN Typt
VIK Vee = 4.5 V, II = -18 mA
MAX
-1.5
MAX
-1.5 V
!::
::l
Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 vee- 2
U
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V a:
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
U
VOL
Vee = 4.5 V 10L = 24 rnA 0.35 0.5
V
en
II
'ALS520 Q inputs Vee = 5.5 V, VI = 5.5 V 0.1 0.1
mA
<t
All other inputs Vee = 5.5 V VI = 7 V 0.1 0.1
C
IIH
'ALS520 Q inputs
Vee = 5.5 V, VI = 2.7 V
-0.2 -0.2 mA z
All other inputs
'ALS520 Q inputs
20
-0.6
20
-0.6
p.A
<t
IlL
All other inputs
Vee = 5.5 V, VI = 0.4 V
-0.1 -0.1
mA en
..J
= =
10+
'ALS520
Vee 5.5 V, Vo 2.25 V -30
12
-112
19
-30
12
-112
19
mA
<t
lee Vee = 5.5 V, See Note 1 mA
'ALS521 12 19 12 19

NOTE 1: lee is measured with Ggrounded and P and Q inputs at 4.5 V.
283
TEXAS 2-337
INSTRUMENTS
switching characteristicl.l (see Note 1)

Vcc = 4.S V to'S.S V.
so pF.
CL =
RL = SOO Q.
FROM TO
(INPUT) (OUTPUT)
SNS4ALSS20 SN74ALSS20
MIN MAX MIN MAX
tpLH 3 16 3 12
P orQ P=Q ns
tpHL S 25 5 20
tpLH 2 15 2 12
G P=Q ns
tPHL 5 23 5 22
NOTE 1. For load circuit and voltage waveforms. see page 1-12.
~
l>
r-
en
l>
2
C
l>
en
(")
3;
(")
c:
=t
en
1283
2·338 TEXAS
INSfRUMENTS
TYPES SN54ALS526, SN54ALS527, SN54ALS528
SN74ALS526, SN74ALS527, SN74ALS528
FUSE·PROGRAMMABLE IDENTITY 02826.
COMPARATORS
DECEMBER 1983
• Can Be Programmed and Verified on Most Programming Capabilities

Incoming Test Equipment 'ALS526 - Fuse Programmable 16·Bit
Identity Comparator
• Reduces Board and Package Size for 'ALS527 - Fuse Programmable 8-Bit
Similar Fixed Comparator Functions Identity Comparator and 4-Bit
• High·Speed Address Recognition Comparator
'ALS528 - Fuse Programmable 12·Bit
• Package Options Include Both Plastic and Identity Comparator
and Ceramic DIPs
and Reliability
SN54ALS526 ..• J PACKAGE SN54ALS527 ... J PACKAGE SN54ALS528 ... J PACKAGE

SN74ALS526 .•• N PACKAGE SN74ALS527 ..• N PACKAGE SN54ALS528 ... N PACKAGE
(TOP VIEW) (TOP VIEW) (TOP VIEW)
G Vee G Vee G Vee

PO p=o PO p=o PO p=o
P1 P15 P1 011 P1 P11
P2 P14 P2 P11 P2 P10
P3 P13 P3 010 P3 P9
..
P4 P12 P4 P10 P4 P8
P5 P11 P5 09 P5 P7
P6 P10 P6 P9 GND P6
P7 P9 P7 08
GND P8 GND P8
CI)
SN54ALS526 .•• FH PACKAGE
SN54ALS526 ..• FN PACKAGE
SN74ALS527 •.. FN PACKAGE
SN74ALS528 •.. FN PACKAGE
!::
(TOP VIEW) (TOP VIEW) (TOP VIEW)
::::>
U
..- 0 Uld
U II
Il.. 1l..1c.9 > Il..
..- 0 Ul
U d
II
Il.. 1l..1c.9 > Il.. 0
1 U °
Old
II
Il..c.9Z>1l..
a:
U
CI)
P2 P15 P2 011 P1 P11 <t
P3 P14 P3 P11 P2 P10
P4 P13 P4 010 Ne NC C
P5 P12 P5 P10 P3 P9 2
P6 P11 P6 09 P4 P8 <t
CI)
..J
....... 0 ( 0 0 ) 0
Il..zll..ll....-
....... 0000(0)
Il..zll..dll..
LnOu<O .......
Il..zzll.ll.. <t
c.9 Il.. c.9 c.9

ThIs document containa Infonnatlon on • product WIder
development. Texa.lnatrumentl re ..rve. the right to TEXAS 2-339
change or discontinue thIa product without notice. INSTRUMENTS
FUSE·PROGRAMMABLE IDENTITY COMPARATORS
description
The' ALS526 and' ALS528 are fuse-programmable identity comparators designed for easy programming
in fixed-comparator applications. The' ALS526 compares a 16-bit data word against a preprogrammed
16-bit data word while the' ALS528 compares a 12-bit data word against a preprogrammed 12-bit data
word. The P = Q output will go low when the applied data word (P inputs) matches the preprogrammed
data word (Q represents the preprogrammed data word). Programming is easily accomplished on the bench
or with conventional automatic test equipment. Special equipment such as PROM-programmers are not
required.
The 'ALS527 is a combination of an 8-bit fuse-programmable comparator and a conventional 4-bit
comparator. For the P = Q output to go low, the applied data word PO through P7 must match the
preprogrammed data word QO through Q7, and the applied data word P8 through P11 must match the
applied data word Q8 through Q 11 .
The SN54ALS526, SN54ALs527, and SN54ALS528 are characterized for operation over the full military
temperature range of - 55 ac to 125 ac.
The SN74ALS526, SN74ALS527, and SN74ALS528 are
characterized for operation from 0 ac
to 70 ac.
programming details
Before any fuses are blown, the inputs are programmed to recognize a low logic level. Therefore, only the
bits that are to be programmed to recognize a high logic level require a fuse to be blown. A fuse is easily
blown by applying 12 volts (VIHH) to the desired P input.pin and also to the G input. This permanently
programs the pin to recognize a high. Only one input pin should be programmed at a time.
verification details
-.J Before the device is programmed, all of the fuses are intact. In this condition, the P = Q output should
go low only if lows are applied to all the P inputs. On the' ALS527, the same is true for the PO and P7
inputs, but in addition, the P8. t~rough P11 inputs must match the Q8 through Q 11 inputs.
It is possible to check the fuse circuitry before actually blowing it in the following manner. By placing a
high (VIH) at the desired P input pin while leaving a low on the G input, the P = Q output should be high.
If the P input is then taken to VIHH, the P = Q output should go low assuming all other P inputs are at
a high level (VIH).
In this condition, the fuse will not be blown as long as G is at VIL. When G is taken to VIHH, the fuse
will be blown and the input will be permanently programmed to recognize a high logic level. The timing
diagram in Figure 1 shows the recommended programming sequence. After all desired input pins have
been programmed, it is easy to verify the device by applying the programmed data word and checking
to be sure that the P = Q output is low.
128
2-340 TEXAS
INsrRUMENTS
'ALS526 'ALS527
PO-.....- - - Q PO-.....- - - d
P15-.....- - - Q P7 - .....- - - d
G G
..
P8
08
P9
09
P10
010
P11
en
011 !::
=>
C,)
'ALS528 a:
C,)
PO
en
<t
C
2:
p~O
<t
P11
en
...J
<t
--------d
i ' i -......
!83
, TEXAS 2-341
INSTRUMENTS
logic symbols
'A LS526 'ALS527
8r
P3
P4
P5
P6
P7
(19) p;n
COMP
~} P=O
}c
08 (12)
09 (14)
(16)
Q10
011 (18)
IB
»
r-
tJ) 'ALS528
»
2
8r
C
»
tJ)
n (15) p;a
::zl
n
C
~
tJ)
"These inputs can be programmed to be active high. The asterisk is not a part of the symbol. For a correct symbol for the programmed device, delete the
polarity symbol (t::::...) at any input whose programming fuse has been blown.
128
2-342 TEXAS
INSTRUMENTS
FUSE-PROGRAMMABLE IDENTITY COMPARATORS
Supply voltage, Vee (see Note 1) ...................... : . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS' . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°e
SN74ALS' ........................... ooce to 70 0 e
Storage temperature range .................................•....-... - 65°C to 150 0 e
NOTE 1: These ratings apply except for programming pins during a programming cycle.

SN54ALS' SN74ALS'
UNIT
VIH High-level input voltage 2 5.5 2 5.5 V
10L Low-level output current 12 24 - rnA

SN54ALS' SN74ALS'
VIK VCC = 4.5 V. II = -18 rnA -1.5 -1.5 V
Vcc· = 4.5 V to 5.5 V. 10H = -0.4 rnA vee- 2 vee- 2
VOH Vcc = 4.5 V. 10H = -1 rnA 2.4 3 V
Vcc = 4.5 V. 10H = -2.6 rnA 2.4 2.9
Vcc = 4.5 V. 10L = 12 rnA 0.25 0.4 0.25 0.4
V
en
VOL
Vcc = 4.5 V. 10L = 24 rnA 0.36 0.5 t:::
II Vec = 5.5 V. VI = 5.5 V 0.1 0.1 rnA :::>
IIH VCC = 5.5 V. VI = 2.7 V 20 20 /lA u
IL Vee = 5.5 V. VIL = 0.4 V -0.2 -0.2 rnA
a:
10+ Vcc = 5.5 V. Vo = 2.25 V -30 -130 -30 -130 rnA
u
en
l'ALS526
ICC l'ALS527
Vcc = 5.5 V.
G input at
All P inputs at 4.5 V.
14
13
14
13 rnA «
l'ALS528
GND
13 13 c
2
*The output conditions have been chosen to produce a current that closely approximates one half of the tue short-circuit output current. lOS' «
....I
Vee = 4.5 V to 5.5 V. «
CL = 50 pF.
PARAMETER
FROM TO RL = .500 n. UNIT
/ (INPUT) (OUTPUT) TA = MIN to MAX
SN54ALS' SN74ALS'
tPLH 8 8
P or Q P=Q ns
tpHL 9 9
tpLH 6 6
G P=Q ns
tpHL 6 6
t All typical values are at Vee = 5 V. T A = 25°e.

Z83
TEXAS 2-343
INSTRUMENTS
programming parameters
PARAMETER MIN MAX UNIT
VIH High-level input voltage 2 5.5 V
VIL Low-level input voltage 0.8 V
VIHH Program-pulse input voltage 10.5 12 V
VCC Supply voltage 5 7 V
Pn(G low) 2.08
IIHH Program-pulse input current mA
G 1.24
'ALS526
ICCHH Supply current with VIHH applied 'ALS527 mA
'ALS528
tw Pulse duration, program 10 50 p's
tr Rise time, program voltage 10 p's
programming waveforms
TEST TEST TEST- BLOW FUSE VERIFY VERIFY YERIFY

14 -/4 -14 -/4 -tf -tf -If -I
- - - - - - - - VIHH
Pn
I - - - - VIH
\"'_ _ _ _ VIL
I4-- t w-+l
lEI I
90"t
I
t
I
I
9 0% - - - - - - - - - - - -V'HH
l> G ____________1_0_%~~
r- \ VIL
tI)
-.j j4-tr
l>
:2
C p:a
l>
tI)
-----'
n ·This test is only true if all other P inputs are at VIH'
::a
n
c
=i
tI)
128:
2-344 TEXAS
INSTRUMENTS
OCTAL O·TYPE TRANSPARENT LATCHES WITH 3·STATE OUTPUTS
• a-Latches In a Single Package SN54ALS533, SN54AS533. J PACKAGE

SN74ALS533, SN74AS533. N PACKAGE
• 3-State Bus-Driving Inverting Outputs
ITOPVIEWI
• Full Parallel Access for Loading
DC VCC
• P-N-P Inputs Reduce D-C Loading on Data Lines 10 80
2D 7D
• Package Options Include Both Plastic and Ceramic 20 70
Chip Carriers in Addition to Plastic and Ceramic DIPs 30 60
• Dependable Texas Instruments Quality and Reliability 3D 6D
4D 5D
description 40 50
GND C
These 8-bit latches feature three-state outputs designed
specifically for driving highly capacitive or relatively low- SN54ALS533,SN54AS533 FH PACKAGE
impedance loads. They are particularly suitable for implementing SN74ALS533,SN74AS533 FN PACKAGE
buffer registers, I/O ports, bidirectional bus drivers, and working ITOPVIEWI
registers. U
OldlU Uld
The eight latches of the' ALS533 and' AS533 are transparent ...... O>co
Ootype latches. While the enable (C) is high, the 0 outputs will 3 2 1
follow the complements of the D inputs. When the enable is 2D 4 8D
taken low, the 0 outputs will be latched at the invers~s of the 20 5 70
levels that were set up at the D inputs. The 'ALS533 and 30 6 70
'AS533 are functionally equivalent to the' ALS373 and' AS373 3D 7 60
except for having inverted outputs. 4D 8 6D
A buffered output-control (DC) input can be used to place the 9 10 11 1213
eight outputs in either a normal logic state (high or low logic IdOUldO
'<tZ LnLn en
levels) or a high-impedance state. In the high-impedance state
the outputs neither load nor drive the bus lines significantly. The
(!)
!::
;:)
high-impedance third state and increased drive provide the (.)
capability to drive the bus lines in a bus-organized system FUNCTION TABLE lEACH LATCH I a:
without need for interface or pull-up components.
INPUTS OUTPUT (.)
Q
The output control does not affect the internal operation of the
latches. Old data can be retained or new data can be entered
OC
L
ENABLE C
H
0
H L
en
L H L H
~
while the 9utputs are off.
L L X 00 c
operation over the full military temperatu~e range of - 55°C to
H X X Z z
~
125°C. The SN74ALS533 and SN74AS533 are characterized
for operation from ooC to 70°C. en
-'
~

83
TEXAS 2-345
INSTRUMENTS
logic svmbol
10---+-4
20~--~
~
l>
r- 40~--+-I
o
l>
z
C
l>
o
S2
::D
o
c:
=t
o
Pin numbers shown ara for J and N packages.
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .' ..... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS533,SN74AS533 . . . . . . . . . . . . . . . . . . . . . . . . 0 0 et070oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . ',' .'. . . . . . . . . . . . . . . . . .. - 65°C to 150°C
12£
2-346 TEXAS
INSTRUMENTS

UNIT
tsu Setup time, data before enable e,j. 15 15 ns
th Hold time, data after enable e,j. 7 7 ns
VIK Vee = 4.5 V, II = - 18 mA -1.5 - 1.5 V
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10L = 24 mA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
10Zl Vee = 5.5 V, VI = 0.4 V -20 -20 p.A en
II Vee
Vee
= 5.5 V,
= 5.5 V,
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
mA
p.A
t::::
IIH :::::>
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
u
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA a::
U
I Outputs disabled 18.5 28 18.5 28 en
<t
*The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS' C
2:
<t
en
..J
<t
83
TEXAS 2-347
INSTRUMENTS

Vcc = 4.5 V to 5.5 V
CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tPLf.I 4 24 4 19
0 Q ns
tpHL 4 14 4 13
tpLH , Any Q
5 28 5 23
C ns
tPHL 4 21 4 18
tpZH 4 19 4 17
OC Any IT ns
tpZL 4 20 4 18
tpHZ 2 12 2 10
DC AnyQ ns
tpLZ 3 22 3 16
o latch signal conventions

It is TI practice to name the outputs and other inputs of a D·type latch and to draw its logic symbol based on the
producing complementary data are called O. An input that causes a Q output to go high or a Q output to go low is called
It) Preset; an input that causes a Q output to go high or a Q output to go low is called Clear. Bars are used over these pin
r-
C/) outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
l>
2
C
l> S (5) Q CLR R (51
Q
C/) C1
C1 C
S2 10
(61 a [) 10
Q
:::D R PRE S
o
c
=t
C/) Notice that Q and Q exchange names. which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (t::::.1 on PRE and CLR remain since these inputs are still active-low. but that the presence or absence of the
polarity indicator changes at D, Q, and Q. Of course pin 5 (01 is still in phase with the data input 15, but now both are
128
2-348 TEXAS
INSTRUMENTS

SN54AS533 SN74AS533
UNIT
tsu Setup time, data before enable e-l- 2 2 ns
th Hold time, data after enable e-l- 3 3 ns
SN54AS533 SN74AS533
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -12 mA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 mA 2.4 3.3
Vee = 4.5 V, IOl = 32 mA 0.29 0.5
VOL V
Vee = 4.5 V, IOl '= 48 mA 0.34 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
IOZl Vee = 5.5 V, VI = 0.4 V -50 -50 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A en
III Vee = 5.5 V, VI = 0.5 V -0.02 -0.5 -0.02 -0.5 mA !::
10:1: Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA ::J
I Outputs high 62 100 62 100 U
Ice Vee = 5.5 V I Outputs low 64 100 64 100 mA
ex:
I Outputs disabled 71 110 71 110 U
t All typical values are at Vee = 5 V, TA = en
25°C. ,
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' «
c
2:
«
en
-J
«
33
TEXAS 2-349
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
SN54AS533 SN74AS533
MIN MAX MIN MAX
tpLH 4 10 4 7.5
D Q ns
tpHL 4 8 4 7
tpLH 5 11 5 9
C Any Q ns
tpHL 4.5 8.5 4.5 8
tpZH 2 7.5 2 6.5
OC Any Q ns
tpZL 4.5 10.5 4.5 9.5
tpHZ 3 7.5 3 6.5
OC Any Q ns
tpLZ 3 8 3 7
- >
r-
en
>
2
C
>
en
Q
:u
(')
c
=t
en
12E
2-350 TEXAS
INSTRUMENTS
OCTAL D·TYPE EDGE·TRIGGERED FLlp·FLOPS WITH 3·STATE OUTPUTS
• 3-State Bus-Driving Inverting Outputs SN54AlS534. SN54AS534 . J PACKAGE

SN74AlS534. SN74AS534. N PACKAGE
• Buffered Control Inputs (TOP VIEW)
Chip Carriers in Addition to Plastic and C?eramic DIPs oc VCC
• Dependable Texas Instruments Quality and Reliability 80
1D 8D
description 2D 7D
70
These 8-bit flip-flops feature three-state outputs designed 60
specifically for driving highly capacitive or relatively low- 6D
impedance loads. Jhey are particularly attractive for implementing 5D
buffer registers, I/O ports, bidirectional bus drivers, and working 50
regi:;ters. GND ClK
The eight flip-flops of the' ALS534 and' AS534 are edge-triggered
D-type flip-flops. On the positive transition of the clock, the Q
outputs will be set to the complement of the logic states that were SN54AlS534. SN54AS534 . FH PACKAGE
set up at the D inputs. The' ALS534 and' AS534 are functionally SN74AlS534.SN74AS534. FN PACKAGE
equivalent to the' ALS374 and' AS374 except for having inverted (TOP VIEW)
outputs. U
~ I~ Ig 5"g
A buffered output-control input can be used to place the eight
3 2 1 2019
outputs in either a normal logic state (high or low logic levels) or
a high-impedance state. In the high-impedance state the outputs 2D 8D
neither load nor drive the bus lines significantly. The high- 20 7D
impedance third state and increased drive provide the capability 30 70
to drive the bus lines in a bus-organized system without need for 3D 65
4D 6D
interface or pull-up components.
9 10 11'1213
en
10 Cl ~ 10 Cl
!::
flip-flops. Old data can be retained or new data can be entered <:tadLnLn :::>
while the outputs are off. C,.)
a:
FUNCTION TABLE (EACH FLIP-FLOP) C,.)
125°C. The SN74ALS534 and SN74AS534 are characterized for INPUTS OUTPUT en
operation from O°C to 70°C. OC ClK 0 Q <t
L t H L
L t L H
C
- :2
L
H
L
X
X
X
00
Z
<t
en
...J
<t
TEXAS 2-351
INSTRUMENTS
logic symbol
10
20
40 (81
50 (131
60 (141
70 (171
80 (181

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS534. SN54AS534 . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS534,SN74AS534 . . . . . . . . . . . . . . . . . . . . . . . . 00eto70oe
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 1 50 °e
12
2-352
TEXAS
INSTRUMENTS
TYPES SN54ALS53tSN74ALS534
OCTAL D·TYPE EDGE·TRIGGERED FLlP·FLOPS WITH 3·STATE OUTPUTS

UNIT
\ elK high 16.5 14
\ elK low 16.5 14
tsu Setup time, data before ClK I 10 10 ns
TA Operating free-air temperature - 55 125 0 70 °C
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA VCC- 2 VCC-2
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V

Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOl = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOl = 24 mA 0.35 0.5
20
IOZH Vee = 5.5 V, Vo = 2.7 V
VI = 0.4 V
20
-20 -20
JlA
JlA
en
IOZl
II
Vee = 5.5 V,
Vee = 5.5 V, VI =7V 0.1 0.1 mA
t::
Vee = 5.5 V, VI = 2.7 V 20 20 JlA
::J
IIH
U
III
\elK, oe
Vee = 5.5 V, VI = 0.4 V
-0.1 -0.1
mA a:
I D -0.2 -0.2
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA U
\ Outputs high 11 19 11 19 en
lee Vee = 5.5 V \ Outputs low 19 28 19 28 mA <t
c
t All typical values are at VCC ; 5 V, TA ; 25°C. 2
tThe output conditions have been chosen to produce a current that closely approximates one half of th7 true short·circuit output current, lOS· <t
en
-I
<t
83
TEXAS 2-353
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 O.
PARAMETER UNIT
(lNPUTI (OUTPUTI R2 = 500 O.
TA = MIN to MAX
MIN MAX MIN MAX
f max 30 35 MHz
tplH 3 15 3 12
ClK Any Q ns
tpHl 5 18 5 16
tpZH 5 19 5 17
OC Any 0: ns
tpZl 7 20 7 18
tpHZ 2 12 2 10
5C Any 0: ns
tplZ 2 16 2 14
o flip-flop signal conventions
..
It is TI practice to name the outputs and other inputs of a D-type flip-flop and to draw its logic symbol based on the
producing complementary data are called Q. An input that causes a Q output to go high or a Q output to go low is called
In some applications it may be advantageous to redesignate the data input 5. In that case all the other inputs and
l> outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
r-
en pin numbers are shown in parentheses.
l>
2
C PRl (5) CLR
Q Q
l> C1 CLK C1
en
0
n (6) -
Q
PRE
::IJ
n
c
=t
en
Notice that Q and Q exchange names. which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (D.o.) on PRE and CLR remain since these inputs are still active-low. but that the presence or absence of the
polarity indicato'r changes at D. Q. and Q. Of course pin 5 (0) is still in phase with the data input 5. but now both are
128
2-354 TEXAS
INSTRUMENlS

SN54AS534 SN74AS534
UNIT
Pulse duration
LelK high 5.5 4
ns
tw
I elK low 5 3
tsu Setup time, data before elK t 3 2 ns
SN54AS534 SN74AS534
-MIN Typt MAX MIN Typt MAX
-18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = -2 mA Vee- 2 Vee- 2
.VOH Vee = 4.5 V, 10H = -12 mA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 mA 2.4 3.3
Vee = 4.5 V, 10l = 32 mA 0.29 0.5
v
VOL
Vee = 4.5 V, 10l = 48 mA 0.34 0.5
10ZH Vee = 5.5 V, Vo = 2.7V 50 50 p.A (J)
10Zl Vee = 5.5 V, VI = 0.4 V -50 -50 p.A t::
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA :::>
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A u
III
loc, elK
Vee = 5.5 V, VI = 0.4 V
-0.5 -0.5
mA
a::
10+
I D
Vee = 5.5 V, Vo = 2.25 V -30
-3
-112 -30
-2
-112 mA
u
(J)
I Outputs high
lee mA Vee = 5.5 V I Outputs low
77
84
120
128
77
84
120
128 mA «
I Outputs disabled 84 128 84 128 c
2
+The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' «
(J)
..J
«
83
TEXAS 2-355
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
FROM TO R1 = 500 n.
UNIT
TA = MIN to MAX
SN54AS534 SN74AS534
MIN MAX MIN MAX
f max 100 125 MHz
tpLH 3 11 3 8
elK Any Q ns
tpHl 4 11.5 4 9
tpZH 2 7 2 6
oe Any Q ns
tpZl 3 11 3 10
tpHZ 2 7 2 6
oe Any IT ns
tpLZ 2 7 2 6
~
»r-
en
»
:2
C
»
en
n
~
n
c
===i
en
128:
2-356 TEXAS
INSTRUMENTS
3·LlNE TO 8·LlNE DECODERS/DEMULTIPLEXERS WITH 3·STATE OUTPUTS
02661. APRIL 1982 - REVISED DECEM8ER 1983
• 3-State Outputs SN54ALS538 . . . J PACKAGE

o Output Polarity Control
(TOP VIEW)
o Data Multiplexing Capability
Y2 Vee
o Multiple Enables for Expansion Y1 Y3
YO Y4
Chip Carriers in Addition to Plastic and Ceramic DIPs OE1 e
OE2 <34
o Dependable Texas Instruments Quality and Reliability A <33
B G2
description Y5 G1
The 'ALS538 decoder/demultiplexer accepts three address input Y6 AL
signals (A, B, C) and decodes them to select one-of-eight GND Y7
mutually exclusive outputs. If the polarity control input (AL) is
high, the outputs are active-low; if AL is low, the outputs are SN54ALS538 . . FH PACKAGE
active-high. Two active-high and two active-low input enables SN74ALS538 . . FN PACKAGE
are available for easy expansion to 1-of-32 decoding with four (TOP VIEW)
packages, or for data demultiplexing to 1-of-8 or 1-of-1 6 U
O...-NUC")
destinations. A high signal on either of the output enables (OE1 >->->->>-
and 0E2) forces all outputs to the high-impedance state.
The SN54ALS538 is characterized for operation over the full OE1 Y4

military temperature range of - 55°C to 125°C. The OE2 e
SN74ALS538 is characterized for operation from 0 °e to 70°C. A <34
B <33
Y5 G2
en
I-
FUNCTION TA8LE (EACH DECODER/DEMULTIPLEXER)
::>
(J
FUNCTION
INPUTS OUTPUTS a:
OE10E2 G1 G2 G3 G4 C 8 A Yo Y1 Y2 Y3 Y4 Ys Y6 Y7 (J
High impedance H X X X X X X X X Z Z Z Z Z Z Z Z
(AL = Xl X H X X X X X X X Z Z Z Z Z Z Z Z en
Disable
L
L
L
L X
L X
L
X
X
X
X
X
X
X
X
X
X All outputs same
«
(AL = Xl L
L
L
L
X
X
X
X
H
X
X
H
X
X
X
X
X
X
level as AL c
2
L
L
L
L
H
H
H
H
L
L
L
L
L
L
L
L
L
H
H
L
L
H
L
L
L
L
L
L
L
L
L
L
L
L «
Active-High
L
L
L
L
H
H
H
H
L L
L L
L
L
H
H
L
H
L
L
L
L
H
L
L
H
L
L
L
L
L
L
L
L
en
-I
Output
(AL = L) L L H H L L H L L L L L L H L L L
«
L L H H L L H L H L L L L L H L L
L L H H L L H H L L L L L L L H L
L L H H L L H H H L L L L L L L H
L L H H L L L L L L H H H H H H H
L L H H L L L L H H L H H H H H H
L L H H L L L H L H H L H H H H H
Active-Low L L H H L L L H H H H H L H H H H
Output
(AL = H) L ·L H H L L H L L H H H H L H H H
L L H H L L H L H H H H H H L H H
L L H H L L H H L H H H H H H L H
L L H H L L H H H H H H H H H H L
283 PRODUCT PREVIEW

TYPES SN54ALS53B, SN74ALS53B
3·L1NE TO B·L1NE DECODERS/DEMULTIPLEXERS WITH 3·STATE OUTPUTS
XIV DMUX
(12) [> AL (12) N10 [>
AL
0e1 EN 0E1 EN
0E2 0E2
(3) (6) (3)
}~
A 0, a,t3\1 YO A 0,10 \1 YO
(2) (7) (2)
B 1, a,t3\1 Y1 B 1,10 \1 Y1
e 2, aj3\1
(1)
Y2
e (17)
2,10 \1 Y2
(19)
3, a,i3\1 Y3 3,10 \1 Y3
(18) &
4, a,t3\1 Y4 G1 (13) 4,10 \1 Y4
(8) Y5
5, a,t3\1 Y5 G2 (14)
Ga (9) (9)
6, uj3 \1 Y6 Y6
(11)
(33 (15)
(11) Y7
7, aj3\1 Y7 (;4 (16
7,10\1
AL
0E1
-
(3)
OE2 YO
A
(2) Y1
»
r-
(1) Y2
CA
»
2
(19) V3
C (18) V4
»
CA· e (8)
V5
Q G1
:0 G2 (9) V6
"=i
C G3 (11)
V7
CA G4
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . ~ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS538 . . . . . . . . . . . . . . . . .'............. - 55 °e to 125 ~e
SN74ALS538 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
128
2-358 TEXAS
INSTRUMENTS
3·LlNE TO 8·LlNE DECODERS/DEMULTIPLEXERS WITH 3·STATE OUTPUTS

VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. IOH = -0.4 mA Vee- 2 vee- 2
VOH Vee = 4.5 V. IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V. IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V. IOl = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 24 mA 0.35 0.5
IOZH Vee = 5.5 V. Vo = 2.7V 20 20 p.A
IOZl Vee = 5.5 V. Vo = OAV -20 -20 p.A
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A
III I A. B. e or AL Vee = 5.5 V. VI = 0.4 V

-0.2 -0.2
mA
I All other -0.1 -0.1
lOt Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
I Outputs high
lee Vee = 5.5 V I Outputs low mA

183
TEXAS 2-359
INSTRUMENTS
TYPES SN54ALS53B. SN74ALS53B
3·LlNE TO B·LlNE DECODERS/DEMULTIPLEXERS WITH 3·STATE OUTPUTS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
R1 = 500 n.
PARAMETER
FROM TO R2 = 500 n. UNIT
(INPUT) (OUTPUn TA = MIN to MAX
tpLH 22 22
A. B.C Any Y ns
tpHL 22 22
tpLH 18 18
Gl or G2 Any Y ns
tpHL 18 18
tpLH 22 22
G3 or G4 Any Y ns
tpHL 22 22
tPLH 20 20
AL Any Y ns
tpHL 20 20
tpZH 10 10
GEl or GE2 Any Y ns
tpZL 13 13
tpHZ 8 8
DEl or OE2 Any Y ns
tpLZ 10 10

NOTE 1: For load circuit and voltage waveforms, see page 1-12_
~ "ddltloM' ;"fo~.';o" 0" tho.. " ..d"" "" •• o''''",d from tho f.""", " It '"om..... ,.bI•.
:t>
r-
CJ)
:t>
2
C
:t>
CJ)
Q
::D
(j
c
=i
CJ)
128:
2-360 TEXAS
INSTRUMENTS
DUAL 2·LlNE TO 4·LlNE DECODERS/DEMULTIPLEXERS WITH 3·STATE OUTPUTS
• 3-State Outputs SN54ALS539 • • . J PACKAGE

SN74ALS539 . . • N PACKAGE
• Output Polarity Control (TOP VIEW)
• Data Multiplexing Capability 1Y2 VCC

1Y1 1Y3
1YO 1B
1AL 1A
• Dependable Texas Instruments Quality and Reliability 10E 1G
2A 2G
description 2B 20E
2Y3 2AL
The' ALS539 decoder/demultiplexer contains two independent
2Y2 2YO
decoders, each of which accepts two address input signals (A
GND 2Y1
and B) and decodes them to select one of four mutually exclusive
outputs. If the polarity-control input (AL) is high, the outputs are
active-low; if AL is low, the outputs are active-high. An active-
low input enable (G) is available for data demultiplexing. Data is
routed to the selected output in nonirtverting form in the active- SN54ALS539 . • . FH PACKAGE
low mode or in inverted form in the active-high mode. A high SN74ALS539 • • . FN PACKAGE
signal on the output enable (OE) forces the 3-state outputs to the (TOP VIEW)
high-impedance state.
The SN54ALS539 is characterized for operation over the full
military temperature range of - 55 to 125 ac
The ac.
SN74ALS539 is characterized for operation from 0 to 70 ac ac.
1AL 1B
10E 1A
FUNCTION TABLE
2A 1<3
(EACH DECODER/DEMULTIPLEXER)
2B 2<3
INPUTS OUTPUTS 2Y3 20E en
FUNCTION
OE G B A YO Y1 Y2 Y3 !::
High Impedance H X X X Z Z Z Z ::>
All outputs same u
Disable L H X X
level as AL a:
Active-high
L L L L H L L L U
Output
L L L H L H L L
en
tAL = LI
L
L
L
L
H
H
L
H
L
L
L
L
H
L
L
H
<t
L L L L L H H H c
Active-low
L L L H H L H H z
Output
tAL = HI
L L H L H H L H <t
L L H H H H H L en
..J
<t

283
PRODUCT PREVIEW
ThI. document contaln.lnformatlan on e product under
development. Tex.. Instruments re.erves the right to TEXAS 2-361
x/v DMUX
Ni3 (3) Nl0 (3)
O.a.{3'V lYO 0.10 'V lYO
(2) EN (2)
1. a.{3'V lYl 1.10 'V lYl
(11 lY2 (11
2.a.{3'V O} 0 2.10 'V lY2
(19) 1 G"j" (19)
3.a.{3'V lY3 3.10 'V lY3
(12) (12)
2YO 2YO
( 11) ( 11)
2Yl 2Yl
(9) (9)
2Y2 2Y2
(8) (8)
2Y3 2Y3
(3) lYO
IIIfJ (2) lYl
l>
....
en )-+-_(_1)-1 Y2
l>
2 lB
}----lY3
(19)
C
l> lG
en
~ 2AL
:a
C') 20E
c: (12)
2YO
~
en (11)
2Yl
(9)
2Y2
(8)
2Y3
1283
2-362 TEXAS
INSTRUMENTS
Supply voltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS539 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS539 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C

UNIT
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. IOH = -0.4 mA vee- 2 vee- 2
VOH Vee = 4.5 V. IOH = -1 mA 2.4 3.3 V
Vee - 4.5 V. IOH = -2.6 mA 2.4 3.2 en
Val
Vee = 4.5 V. IOl = 12 mA 0.25 0.4 0.25 0.4
V C:
Vee = 4.5 V. IOl = 24 mA 0.35 0.5 ::>
IOZH Vee = 5.5 V. Va = 2.7 V 20 20 p.A u
IOZl Vee = 5.5 V. Vo = 0.4 V -20 -20 p.A r::c
II
IIH
Vee = 5.5 V.
Vee = 5.5 V.
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
mA
p.A
u
l A. B. e or Al en
III
I All other Vee = 5.5 V. VI = 0.4 V
-0.2
-0.1
-0.2
-0.1
mA «
lOt Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA c
I Outputs high 2
Ice Vee = 5.5 V I
I
Outputs low mA «
en
...J
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS' «
283
TEXAS 2-363
INSTRUMENlS
TYPES SN54ALS539 t SN74ALS539

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
TA = MIN to MAX
tPLH .y 22 22
A or B ns
tpHL 22 22
tpLH 18 18
G Y ns
tPHL 18 18
tPLH 22 22
AL Y ns
tpHL 22 22
tpZH 10 10
DE Y ns
tpZL 13 13
tPHZ 8 8
BE Y ns
tpLZ 10 10
tAli typical values are at Vee = 5 V. TA = 25°C.

l>
r-
en
l>
:2
C
l>
en
Q.
:c
n
c
=t
en
·1283
2-364 TEXAS
INSfRUMENTS
• 3·State Outputs Drive Bus Lines or Buffer SN54ALS540. SN54ALS541 .•• J PACKAGE
Memory Address Registers SN74ALS540. SN74ALS541 ... N PACKAGE
ITOPVIEWI
• P-N-P Inputs Reduce D-C Loading
• Data Flow-Thru Pinout (All Inputs on Opposite <31 Vee
Side from Outputs) A1 <32
• Package Options Include Both Plastic and A2 Yl
Ceramic Chip Carriers in Addition to Plastic A3 Y2
and Ceramic DIPs A4 Y3
A5 Y4
• Dependable Texas Instruments Quality and A6 Y5
Reliability A7 Y6
AB Y7
GND YB
description
These octal buffers and line drivers are designed to have
the performance of the popular SN54ALS240/SN74ALS240 SN54ALS540. SN54ALS541 •.• FH PACKAGE
series and. at the same time. offer a pinout with inputs and SN74ALS540. SN74ALS541 •.. FN PACKAGE
outputs on opposite sides of the package. This arrangement ITOPVIEWI
greatly enhances printed circuit board layout.
U
N ...... UN
The three-state control gate is a 2-input NOR such that if « «1C!l >1C!l
either <31 or <32 is high. all eight outputs are in the high-
impedance state.
A3 Y1
The •ALS540 provides inverted data and the •ALS541 A4 Y2
provides true data at the outputs. A5 Y3
A6 Y4
The -1 versions of the SN74ALS540 and SN74ALS541
A7 Y5
parts are identical to the standard versions except that the
recommended maximum IOL is increased to 4B
milliamperes. There are no -1 versions of the SN54ALS540 CXlOCXlr--CO
<(2)->->-
and SN54ALS541. C!l
The SN54ALS540 and SN54ALS541 are characterized for

operation over the full military temperature range of - 55 °e
to 125°e. The SN74ALS540 and SN74ALS541 are
characterized for operation from ooe to 70 oe.
~B3 ADVANCE INFORMATION Copyright ©·1982 by Texas Instruments Incorporated
ThIs document contains information on a new product.

Specifications ar. subject to change without notice. TEXAS 2-365
INSTRUMENTS
logic symbols
'ALS540 'ALS541
A1 A1
A2 A2
A3 A3
A4 A4
A5
A6
A7
(9)
AS
..
'ALS540 'ALS541
(1 ) (1)
01 Gl
(19) (19)
G2 G2
»
r- Al
(2) (lS)
Vl Al
(2) (18)
Vl
en
»
2
A2 (3) (17)
V2
A2 (3) (17)
V2
C (16) (16)
» A3 (4) (4)
V3 A3 V3
en
-
(15) (15)
0 A4 (5) V4 A4 (5) V4
:0
0 A5 (6) (14) A5 (6) (14)
C V5 V5
=i
en A6 (7) (13)
V6
A6 (7) (13)
V6
A7 (8) (12) (S) (12)

V7 A7 V7
A8 (9) (11) (9) (11)

V8 AS V8
12E
2-366 TEXAS
INSTRUMENlS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS540, SN54ALS541 . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS540,SN74ALS541 . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . .. - 65 °e to 1 50 °e

12 24
48 t
tThe extended limit applies only if Vee is maintained between 4.75 V and 5.25 V.
The 48 mA limit applies for the SN74ALS540-1 and SN74ALS541-1 only_
PARAMETER TEST CONDITIONS UNIT (/J
MIN TYP:l: MAX MIN TYP:l: MAX
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
!::::
Vee = 4.5 V to 5.5 V. IOH = -0.4 mA Vee- 2 vee- 2
u=>
VOH
Vee - 4.5 V.
Vee = 4.5 V.
IOH -
IOH = -12 mA
-3 mA 2.4
2
3.2 2.4 3_2
V a:
Vee = 4.5 V. IOH = -15 mA 2 U
Vee =: 4_5 V. IOl = 12 mA 0.25 0.4 0.25 0.4 (/J
VOL
Vee = 4.5 v.
= 5.5 V.
loL = 24 mA
Vo = 2.7 V
0.35 0.5
V
«
IOZH
IOZl
Vee
Vee = 5.5 V. Vo = 0.4 V -20
20 20
-20
p.A
p.A
c
2:
II
IIH
Vee
Vee
= 5.5 V.
= 5.5 V.
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
rnA
p.A «
III Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 rnA (/J
...J
lo§ Vee = 5.5 V. Vo = 2.25 V
Outputs high
-30
15
-112 -30
15
-112 mA
«
'AlS540 Vee = 5.5 V Outputs low 18 18 mA
ICC
Outputs high 15 15
'AlS541 Vee = 5.5 V Outputs low 18 18 rnA
tAli typical values are at Vee; 5 V. TA ; 25°e.

!83
TEXAS 2-367
INSTRUMENTS
Vcc = 4.5 V to 5.5 V •

. CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA =
MIN to MAX
tpLH 6 6
A Y ns
tpHL 6 6
tpZH y 13 13
G ns
tpZL 18 18
tpHZ y 7 7
G ns
tpLZ 11 11

Vcc = 4.5 V to 5.5 V.
CL = 50 pF,
R1 = 500 Q,
fROM TO
PARAMETER R2 = 500Q, UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
IH tpLH
A Y
MIN Typt MAX
6
MIN Typt MAX
6
ns
»r- tpHL
tpZH
G y
6
13
6
13
ns
en tpZL 18 18
»
2
tpHZ
tpLZ
G y 7
11
7
11
ns
C tAli typical values are at VCC = 5 V, TA = 25°C.
»
en
(")
::c
(")
c
=i
en
128
2-368 TEXAS
INSTRUMENTS
SYNCHRONOUS 4-81T COUNTERS WITH 3-STATE OUTPUTS
• Carry Output for n-Bit Cascading SN54ALS560A, SN54ALS561A. , , J PACKAGE

• Buffer-Type Outputs Drive Bus Lines Directly (TOP VIEW)
• Choice of Asynchronous or Synchronous Load or Clear
ALOAD VCC
• Internal Look-Ahead for Fast Cascading CLK RCa
• Package Options Include Both Plastic and Ceramic A CCO
Chip Carriers in Addition to Plastic and Ceramic DIPs s G
C QA
• Dependable Texas Instruments Quality and Reliability D Qs
ENP Qc
ACLR QD
ENT
GND SLOAD
SN54ALS560A, SN54ALS561A ... FH PACKAGE

description
The' ALS560A decade counters and' ALS561 A binary counters (TOP VIEW)
are programmable and offer synchronous and asynchronous
clearing as well as synchronous and asynchronous loading. All
synchronous functions are executed on the positive-going edge
of the clock.
The clear function is initiated by applying a low level to either B CCO

Asynchronous Clear (ACLR) or Synchronous Clear (SCLR). C
Asynchronous (direct) clearing overrides all other functions of D
the device, while synchronous clearing overrides only the other ENP en
synchronous functions. Data is loaded from the A, B, C, and D ACLR I-
inputs by applying a low level to Asynchronous Load (ALOAD) or
::>
by the combination of a low level at Synchronous Load (SLO~D)
and a positive-going clock transition, The counting function is 010 0
0::
dZ~r5d
1mt!Jg
I-
U
a::
enabled only when Enable p' (ENP), Enable T (ENT), ACLR,
ALOAD, SCLR, and SLOAD are all high.
m u
en
A high level at the Output Enable (G) forces the Q outputs into the high-impedance state, and a low level enables those
outputs, Counting is independent of 13, ENT is fed forward to enable the Ripple Carry Output (RCa) to produce a high-
«
level pulse while the count is-maximum (9 or 15). The Clocked Carry Output (CCO) produces a high.level pulse for a c
2
duration equal to that of the low level of the clock when RCa is high and the counter is enabled (both ENP and ENT are
high); otherwise, CCO is low. CCO does not have the glitches commonly associated with a ripple-carry output. «
Cascading is normally accomplished by connecting RCa or CCO of the first counter to ENT of the next counter, en
..J
However, for very-high-speed counting, RCa should be used for cascading since CCO does not become active until the
clock returns to the low level. «
The SN54ALS560A and SN54ALS561A are characterized for operation over the full military temperature range of
-55°C to 125°C. The SN74ALS560A and SN74ALS561A are characterized for operation from O°C to 70°C.

283
TEXAS 2-369
INSTRUMENTS
SYNCHRONOUS 4·81T COUNTERS WITH a·STATE OUTPUTS
FUNCTION TABLE
INPUTS
OPERATION
G Ami" ALOAD SCLR SLOAD ENT ENP CLK
H X X X X X X X Q Outputs Disabled
L L X X X X X X Asynchronous Clear
L H L X X X X X Asynchronous Load
L H H L X X X t Synchronous Clear
L H H H L X X t Synchronous Load
L H H H H H H t Count
L H H H H L X X Inhibit Counting
L H H H H X L X Inhibit Counting
logic symbols
'ALS560A 'ALS561A
CTRDIV10 CTRDIV16
1& 6CT=O [SYNC CLR)

M3 [COUNT)
:t>
r
en ClK
Z7
C6/1, 2,3,5+ ClK C6/1,2,3,5+
:t> AClR RCa

ACi:R
:2 A't'5A5 ALOAD
0 A 4,6D/8D A
(4)
:t> B B
en C
(5)
(6)
C
D
0 D
::u
0
c
=i
en
128
2·370 TEXAS
INSTRUMENTS
SYNCHRONOUS 4·81T COUNTERS WITH 3·STATE OUTPUTS
'ALS560A logic diagram (positive logic)
a l 17) ........
-....
(12)
~~
ENT
~
(7) (18)
ENP
.... cco
(9) "
.... (19)
~
RCO
ClK
1111
(2)
(8)
~
';:.
If'
AclR
AlOAO
(1) ... ,........
........
-"
-
A
(3) 1
" - I
~ r---
~
kR I-
- ~S
k~C1
10
-cJC
b- ~)
"--- -v
8
(4) 1 .....
....
~~
I
I ~~
- ;CR
f<s
Ki>C1
~-v
I-
A ~)
08
.. en
!:::
I :l
~
U
IS) 1
....r.....
,..--- a:
C
t '--
:~
~R
U
- -<s
Ki>C1
~
b.£
..... -
~
(14)
Oc en
«
c
- I - 2
«
(6) 1
".... t
-~ en
o
P-l--'=
~
-<;- -
-os ..J
-o>C1
~,....
£ (13)
- 00
«
283
TEXAS 2-371
INsrRuMENTS
SYNTHRONOUS 4·811 COUNTERS WITH 3·STATE OUTPUTS
'ALS561A logic diagram (positive logic)
_ 1171
G ,...
-"
1121
~
ENT
ENP
m
191 " forn " 41

(18)
ceo
rrrru
- v
~~
1191
Reo
1111
[!D-
121
CLK
ACLR
181 ';,.
111 I -c{) ;:
ALOAO -v
A
131
"v ~y-= ~~-
~r
1
-<s
K:t>el~ 1161
r--
10
-
-
IIIIIfI -
~
141
"-
v I r---
~~I
-<lR _
l> .......... -<lS

KlP>el~
r- 10 ~ 08
C/) L--
l>
2
C
e
151
1 "v
I ~ r---
~Err
l> ~
t-<R f-
~ s
C/) ~p>el ..hl (14)
~ - .... Oe
(')
:JJ
(')
C
-I
C/) 0
(6)
1 ".... I -~
-):L::~ r;-
~iF
f-
f-cs
.......... l(P>Cl~
~ .... 00
128<
2-372 TEXAS
INSTRUMENTS
•ALS560A typical load. count. and inhibit sequences
LJ
I
I
I
LJ
I
ENP~
I
ENT~ ~DON'T CARE~
I I
CLK
RCO
C
ccO 2!
ASYNC
I
ASYNC SYNC SYNC
HI-Z
COUNTING CONTINUES
5 I-- INHIBIT COUNTING ---I «
CLEAR LOAD CLEAR LOAD
1283
TEXAS 2-373
INSTRUMENTS
SYNCHRONOUS 4·811 COUNTERS WITH 3·STATE OUTPUTS
'ALS561A typical load, count, and inhibit sequences
AClR -.J
SCLR LJ I
ALOAD --u I
.I
I
SlOAD I I LJ
I I I
ENP ~
I
~ DON'T CARE ~
I I
r---
ENT ~ EDON;T CARE3
I I
ClK
~PON~(f~~~ 1~~qrt'!~>J\R>E~
~~~<~~~~~I I I I I
~DoNYcARE~~ 1~~iioN'YCARE~
""'''<",> I I I >, " I I
~~ql·a,<;A,R.E~ I~Dq~,!,C>J\R,E~
-.J I I
I
~~~qq~;>q~'tE~ 1~~DorfT,CAN~~~
I I
I I I I
l> _...:....---J~ ~~HI-Z~~

r-
en L . -_ _
I
~-,"I_---I
I
~HI-Z~
I
l> I I I
2 Qc --1 "--__'---"1 r-.:~""~""\Z"""H"""'I_Z"""~""~"'~~v---::--------
C I I I I
QD ~ '--....I! ~HI-Z~
l> L--_ _
en RCO
I
__~I______----Ir-l~ ______~I____~r-l
I I
I
I
I
(") I I I
::D CCO __-'"'________--'rl~_____'"__~I______~rl I
(") 112 13 14 15 0 113 14 15 0 , 1 HI-Z 5 I-t-- INHIBIT COUNTING --I
C ASYNC ASYNC SYN SYNC CONTINUE COUNTING
~ CLEAR lOAD CLEAR lOAD

CJ)
1283
2-374 TEXAS
INSTRUMENlS
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS560A, SN54ALS561 A . . . . . . . . . . . . . . . .. - 55°C to 125°C
SN74ALS560A, SN74ALS561A ................... , ooe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C

Q outputs -1 -2.6
10H High·level output current mA
CCO and RCO -0.4 -0.4
Q outputs 12 24
IOL low-level output current mA
CCO and RCa 4 8
'AlS560A 0 18 0 20
'AlS561A 0 25 0 30
ACLR or AlOAD low 20 15
ClK high 27.5 25
'AlS560A
tw Pulse duration ClK low 27.5 25 ns
ClK high 20 16.5
'AlS561A
ClK low 20 16.5
High 25 20
ENP, ENT
low 25 20 en
Data at A, B, C, D
low
25
21
20
15
~
tsu Setup time before ClKt SClR ns :::>
High (inactive) 35 30
u
SlOAD
low 20 15 a:
High (inactive)
AClR or AlOAD inactive
35
10
30
10
u
th Hold time after ClKt for data, ENP, ENT, SClR, or SlOAD 0 0 ns en
TA Operating free-air temperature -55 125 0 70 DC c::(
c
z
c::(
en
...J
c::(
1283
TEXAS 2-375
INSTRUMENTS
SYNCHRONOUS 4-81T COUNTERS WITH 3-STATE OUTPUTS
PARAMETER TEST CONDITIONS SN54AlS561A SN74AlS561A UNIT
V,K Vee = 4.5 V, -18 mA -1.5 -1.5 V
" =
All outputs Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Q outputs
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOl = 12 mA 0.25 0.4 0.25 0.4
Q outputs
Vee = 4.5 V, IOL = 24 mA 0.35 0.5
Val V
Vee = 4.5 V, IOl = 4 mA 0.25 0.4 0.25 0.4
ceo and ReO
Vee = 4.5 V, IOl = 8 mA 0.35 0.5
IOZH Vee = 5.5 V, Va = 2.7 V 20 20 p.A
IOZl Vee = 5.5 V, Va = 0.4 V -20 -20 JlA
ENT and ENP 0.2 0.2
Vee = 5.5 V, V, = 7 V mA
" Other inputs 0.1 0.1
ENT and ENP 40 40
"H Vee = 5.5 V, V, = 2.7 V JlA
Other inputs 20 20
',l Vee = 5.5 V, V, = 0.4 V -0.2 -0.2 mA
eeo and ReO -15 -70 -15 -70
lot Vee = 5.5 V, Vo = 2.25 V mA
Q -30 -112 -30 -112
LOutputs low
-
lee Vee = 5.5 V 21 33 21 33 mA

+-The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
l>
r-
~
l>
:2
C
l>
CJ)
(")
:XJ
(")
c
=i
CJ)
1283
2-376 TEXAS
INSTRUMENTS
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
R1 = 500 n,
R2 = 500 n,
FROM TO
PARAMETER TA = MIN to MAX· UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX
'ALS560A 18 20
f max MHz
'ALS561A 25 30
tplH 4 15 4 12
ClK Any Q ns
tpHl 5 21 5 18
tplH 9 35 9 29
ClK RCO ns
tPHl 8 29 8 24
tplH 8 31 8 26
ClK CCO ns
tpHl 5 20 5 16
tplH 10 38 10 35
AlOAD Any Q ns
tpHl 7 27 7 23
. tplH 15 50 15 40
AlOAD RCO ns
tpHl 12 35 12 30
tplH 25 65 25 55
AlOAD CCO ns
tPHl 12 42 12 33
tplH A, B, C, 8 35 8 30
Any Q ns
tPHl or 0 7 27 7 22
tplH 5 20 5 16
ENT RCO ns
tpHl 4 18 4 14
tplH
ENT CCO
12 35 12 32
ns
en
tPHL 4 15 4 12 t::::
tplH 5 22 5 18 =>
tpHL
ENP CCO
4 14 4 12
ns
u
tpHL ACIR' Any Q 7 28 7 22 ns a:
tpZH
G Any Q
5 24 5 19
ns
u
tpZL 8
2
28 8
2
23
10
en
tpHZ
tPlZ
G Any Q
4
12
20 4 15
ns <t
C
z
<t
en
..J
<t
283
TEXAS 2-377
INSTRUMENTS
- l>
r-
fA
l>
2
C
l>
fA
C')
55
C')
c
=t
fA
2-378
02661. DECEMBER 1982-REVISED DECEMBER 1983
o 3-State Buffer-Type Outputs Drive Bus-Lines Directly SN54ALS563 . . . J PACKAGE

• Bus-Structured Pinout (TOP VIEW)
o Package Options Include Both Plastic and Ceramic Chip
Carriers in Addition to Plastic and Ceramic DIPs OC VCC
1D 15
o Dependable Texas instruments Quality and Reliability 2D 25
3D 30
4D 45
description 5D 55
These 8-bit latches feature three-state outputs designed 6D 65
specifically for driving highly capacitive or relatively low- 7D 70
impedance loads. They are particularly suitable for implementing 8D 85
buffer registers, 1/0 ports, bidirectional bus drivers, and working GND C
registers.
The eight latches are transparent D-type latches. While the

enable (C) is high the Q outputs will follow the complements of SN54ALS563 . . . FH PACKAGE
data (D) inputs. When the enable is taken low the output will be SN74ALS563 . . . FN PACKAGE
latched at the inverses of the levels that were set up at the D
(TOP VIEW)
inputs.
U
A buffered output-control input can be used to place the eight ~ ~Ig ~I~
outputs in either a normal logic state (high or low logic levels) or a 3 2 1 20 19
high-impedance state. In the high-impedance state the outputs
20
neither load nor drive the bus lines significantly. The high-
30
impedance state and increased high-logic level provide the
40
capability to drive the bus lines in a bus-organized system
50
without need for interface or pull-up components.
60 en
The output control (OC) does not affect the internal operation of
the latches. Old data can be retained or new data can be entered
!:::
0 0 Uldld :::>
while the outputs are in the high-impedance state. roz
(!)
rot--
u
The SN54ALS563 is characterized for operation over the full a:
military temperature range of -55°C to 125°C. The
FUNCTION TABLE
(Each Latch)
u
SN74ALS563 is characterized for operation from 0 °C to 70°C.
INPUTS en
ENABLE
OUTPUT-
Q
<t
OC C D C
L H H L 2
L H L H <t
L L X 00
H X X Z
en
...J
<t

1283
TEXAS 2-379
INsrRuME~1S

OC _(1_)_ _--q
(11)
c
10 (2)
OC
10
20 30,(4)
3D
40 40
50 50
40...:.,(5";')_-+--4
60 60
70 70
80 80 50 (6)
60...:.,(7";')_-+--4
70 (8)
80 (9)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125 DC
SN74ALS563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 150°C

UNIT
tsu Setup time, data before enable el 10 10 ns
th Hold time, data after enable e I 10 10 ns
1283
2-380 TEXAS
INSTRUMENTS
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vcc- 2 Vcc- 2
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 24 mA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
IOZL Vee = 5.5 V, VI = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lot Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA
lec Vee = 5.5 V I Outputs low 15 24 15 24 mA
I Outputs disabled 16 . 27 16 27
t All typical values are at VCC = 5 V, T A = 25°C.

switching characteristics (see Note, 1)

PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
CL = SO pF.
R1 =
R2 = SOOQ.
TA =
SOOQ.
MIN to MAX
UNIT
m-en
MIN
SNS4ALSS63
MAX MIN
SN74ALSS63
MAX
!:::
:::J
tpLH
0 6
3 21 3 18
ns U
tpHL 3 15 3 14 a:
tpLH 8 29 8 22
e 6
8 22 8 21
ns U
tpHL
21 4 18 en
tpZH
tpZL
oe 6
4
4 21 4 18
ns
«
tpHZ
OC 5.
2 10 2 8
ns c
tpLZ 3 15 3 13 2
«
en
...J
«
283
TEXAS 2-381
INSTRUMENTS
- l>
r-
en
l>
:2
C
l>
en
~
::a
(')
c
=i
en
2-382
WITH 3'-STATE OUTPUTS
• 3-State Buffer-Type Inverting Outputs Drive Bus-Lines SN54AlS564 . . . J PACKAGE

Directly SN74AlS564 ••• N PACKAGE
(TOP VIEW)
• Bus-Structured Pinout
DC Vce
• Package Options include Both Plastic and Ceramic Chip 20 20
Carriers in Addition to Plastic and Ceramic DIPs 30. 30
40 4Q
• Dependable Texas Instruments Quality and Reliability 50 50
60 60
description 70 70
These 8-bit registers feature inverting three-state outputs 80 80
designed specifically for bus driving. They are particularly GNO ClK
suitable for implementing buffer registers, I/O ports, bidirectional
bus drivers, and working registers.
SN54AlS564 • • . FH PACKAGE
The eight-bit edge-triggered O-type flip-flops enter data on the SN74AlS564 . . . FN PACKAGE
low-to-high transition of the clock. (TOP VIEW)
U
flip-flops. Old data can be retained or new data can be entered
°N..-O>..-
0IU UIO
while the outputs are in the high-impedance state.
The SN54AlS564 is characterized for operation over the full 30

military temperature range of - 55°C to 125°C. The 40
SN74AlS564 is characterized for operation from 0 °C to 70°C. 50
60
FUNCTION TABLE
(EACH FLIP-FLOP)
INPUTS OUTPUT
OC ClK 0 a
L t H L
L t L H logic symbol
L L X 00
H X X Z
(1)
OC
(11)
eLK
(2)
10
(3)
20
(4)
30
(5)
40
(6)
......----4o
50 r---------~~~50
(7)
60 ......---....;... 6~
70 ~-----------L 70
80 r---------~~18Q

1283
TEXAS 2-383
INSTRUMENlS
OCTAL D·TYPE EDGE·TRIGGERED FLlP·FLOPS

OC (11
elK (11)
10 (21
20 (31
3D (41
(161
..
40 (51 40
(151
50 (61 50
l>
r-
en
l> 60 (71
(141
:2 60
C
l>
en
(13) _
~ 70 (81 70
::D
(")
c
=t
en 80
(91 (121 _
80
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS564 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS564 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCt070oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 6·5 DC to 150 DC
1283
2-384 TEXAS
INSTRUMENTS
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS

UNIT
tw Pulse duration
I elK high 16.5 14
ns
I elK low 16.5 14
tsu Setup time, data before elK t 15 15 ns
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V, IOl = 12 rnA 0.25 0.4 0.25 0.4
Val V
Vee = 4.5 V, IOl = 24 rnA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7V 20 20 p.A
IOZl Vee = 5.5 V, VI = 0.4 V -20 -20 /LA
II Vee = 5.5 V, VI =7V 0.1 0.1 rnA en
IIH Vee = 5.5 V, VI = 2.7 V 20 20 /LA !::
IlL Vee = 5.5 V, VI = 0.4 V. -0.2 -0.2 rnA :J
lot Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 rnA ()
I Outputs high 10 17 10 17 a:
lee Vee = 5.5 V I Outputs low 15 24 15 24 rnA ()
tAli typical values are at Vee = 5 V, TA = 25°e. en
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' <t
C
Z
Vcc = 4.S V to S.S V, <t
FROM TO
CL = SO pF,
R1 = SOO Q,
en
-I
PARAMETER
(INPUT) (OUTPUT) R2 = SOO Q,
UNIT
<t
TA = MIN to MAX
MIN MAX MIN MAX
f max 30 35 MHz
4
tplH
tpHl
elK a 4
15
15
4
4
14
14
ns
4 4
tpZH·
tpZl
OC a 4
21
21 4
18
18
ns
tpHZ 2 10 2 8
oe IT ns
tplZ 3 15 3 13
1283
TEXAS 2-385
INSTRUMENTS
- l>
r-
CJ)
l>
2
C
l>
CJ)
o
:ao
c:
=i
en
2-386
02661. APRIL 1982- REVISED DECEM8ER 1983
• 3-State Q Outputs Drive Bus Lines Directly SN54ALS568A. SN54ALS569A •.. J PACKAGE
• Counter Operation Independent of 3-State Output (TOP VIEW)
• Fully Synchronous Clear. Count. and Load U/O VCC
• Asynchronous Clear Also Provided ClK RCO
A CCO
• Fully Cascadable B G
• Package Options Include Both Plastic and Ceramic C OA
Chip Carriers in Addition to Plastic and Ceramic DIPs D OB
ENP Oc
• Dependable Texas Instruments Quality and Reliability AClR OD
SClR ENT
description GND LOAD
The' AlS568A decade counters and' ALS569A binary counters
SN54ALS568A, SN54ALS569A •.. FH PACKAGE
are programmable, count up or down, and offer both synchronous
and asynchronous clearing. All synchronous functions are
(TOP VIEW)
executed on the positive-going edge of the clock.
The clear function is initiated by applying a low level to either

~IO U U
...J -.
<t:U=»a:
UIQ
Asynchronous Clear (ACLR) or Synchronous Clear (SCLR).
3 2 1
Asynchronous (direct) clearing overrides all other functions of
B 4 CCO
the device, while synchronous clearing overrides only the other
synchronous functions. Data is loaded from the A. B, C, and D
C 5 G
D 6 OA
inputs by holding Load (LOAD) low during a positive-going clock
ENP 7 Os
transition. The counting function is enabled only when Enable P
ACLR 8 Oc
(ENP) and Enable T (ENT) are low and AClR, SClR. and lOAD
are high. The Up/Down (U/O) input controls the direction of the
count. These counters count up when U/O is high and count a: 010II- 0
dz<t:~O en
down when U/O is low. Im<.9g !=
A high level at the Output Enable ((3) forces the 0 outputs into the high-impedance state, and a low level enables those :::>
outputs. Counting is independent of of G. ENT is fed forward to enable the Ripple Carry Output (RCO) to produce a (J
low-level pulse while the count is zero (all 0 outputs low) when counting down or maximum (9 or 15) when counting a:
up. The Clocked Carry Output (CCO) produces a low level pulse for a duration equal to that of the low level of the clock (J
when RCO is low and the counter is enabled (both ENP and ENT are low); otherwise, CCO is high. CCO does not have
the glitches commonly associated with a ripple-carry output. Cascading is normally accomplished by connecting RCa
en
or CCO of the first counter to ENT of the next counter. However, for very-high-speed counting. RCO should be used for
<t
cascading since CCO does not become active until the clock returns to the low level. C
Z
The SN54ALS568A and SN54ALS569A are characterized fo~ operation over the full military temperature range of
<t
-55°C to 125°C. The SN74ALS568A and SN74ALS569A are characterized for operation from OoC to 70 o e.
en
....I
<t

1283
TEXAS 2-387
INSTRUMENTS
FUNCTION TABLE
INPUTS
OPERATION
'G ACLR SCLR LOAD ENT ENP UfD CLK
H X X X X X X X Q Outputs Disabled
L L X X X X X X Asynchronous Clear
L H 'L X X X X t Synchronous Clear
L H H L X X X t Load
L H H H L L H t Count Up
L H H H L L L t Count Down
L H H H H X X X Inhibit Count
L H H H X H X X Inhibit Count
logic symbols
'ALS568A 'ALS569A
CTROIV10 CTROIV16
lEI ...!;;.:,*---r:> C511.4.7.8+/2.4.7.8- ':'=':"+---f:> C5f1.4.7.8+f2.4.7.8-

l>
r-
en
l>
2
C
l>
en (161
0A
(151
C') (141 Os
:z:J
C')
(131 ~~
C
~ Pin numbers shown are for J and N packages,
en
1283
2-388 TEXAS
INSTRUMENTS
, ALS568A logic diagram (positive logic)
G (1 71 Joo.
...... .....
UfO (11 J<o.. .....
(2) ...........
ClK
(12) .... ........... (181
ENT
~
&n~
ENP
(7)
...... (191
SClR
'.'¢~
U ~'
(111
(8) .....
.....
A
131
- .......-
1
B
141
-W K~C1
f - - 1D
~-+-c R
"--
r----
1 ~
r
,... 1161
~ ..
~~C1
1 1 - - 1D
",""-<lR
r
.......
(15)
OB
L........- T 1
-- ~
en
K~ 1
(51
~
C
f-";"'" 1D
t:::
:::l
~-(I R
6= (14)
Oc
U
"--
I a:
~
'-J- U
(6) en
&-~~I «
D
L I - - 1D
L-c R
....['""(13)
aD
c
V- Z
- ~ «
"--
en
-I
«
1283
TEXAS 2·389
INSTRUMENTS
,AlS569A logic diagram (positive logic)
G (17)
,....
-"'"
....
UfO
(1)
12'
.........
.....
1
.... -
CLK
ENT
1121 .... - ~ (18)
LQ~
(7) ~ -'"
(19)
'91~~
(11 )
-
(8)
.....
Joo... :~ ~
(3)
,-~
A ~
~>C1
,-f- 1D
. -+-c I......-
R r..... (16)
B
(4)
-
......--
~I>C1
ait
•
J Y
-
' - ' - 1D
~I-< R r
,.... (15)
~
r--r L...-
~ (5)
......-- -
~
C
»
r- - - ~I>C1
1-1- 1D
£
en - ~I-< R ,.... (14)
Oc
~
» --r L...-
2 (6)
C
~--
D
»
en
~ rr=3
_ L...c>C1
f--1D
l......-<: R
.,.["" (13)
-v OD
~
0
~p----
:Jl
0
c
=i
en
1283
2-390 TEXAS
INSTRUMENTS
TYPES SN54ALS568A, AN74ALS568A
SYNCHRONOUS 4·811 UP/DOWN DECADE COUNTERS
'ALS568A typical load, count, and inhibit sequences
AClR --1
SClR ~ LJ
I
lOAD ~ I LJ
I I
ENP ~ ~R~~:t:9~~~~ L-
I I
ENT ~ ~p.~~:t:9~H~~
I I
UfO I
I
ClK
B ~PA~;tA~~~WJ IR9~:t:9~M_
I I I I I I I I
C~p'9N;t:9~~:(®J l_p:q~:tM~~_
I I I I I I I I
o ~p'9~:t:¢M~@ l_p:q~:t:C~~E_
I I I I I I I I
0A I I &...;..1_ _ _ _ __
I I I
Mb):~m L.U en
Oc ~
I I t:
I
____~~~B~E~~~~~rtl~______________ ::l
I I I U
00
mH.;*m I a:
LJ LJ U
en
I I I
Uo I Ug <t
17 18 2 3 4 3 2 0 8 ,I
1 2
14-CO~pNT +I 0
1C114f-----COUNT UP----1.*-·IIIII---COUNT DOWN----.~I4-••NH.B.T COU~T'NG-«>I c
2:
ASYNC SYNC SYNC
CLEAR CLEAR lOAD <t
en
....I
<t
1283
TEXAS 2-391
INSTRUMENTS
•ALS569A typical load. count. and inhibit sequences
G ________________________ ~
lOAD ~ I LJ
I I
ENT ~~~____~~D~l9~N~t~~~~~~~~~----------~----~~----------------__~~
I I
I 1®§pP:~J M~~Wt
I I
ClK I
I I I I I I I I
I I I I
»r- OB 11 ~~ii~
I I
LU
I
en Oc ~EI~i~ rn
»
2 aD
I
~:t[~~
I I
I
C ~ I LJ LJ
»
en
I
~ I
1 2
I
0 14 15 UO 2 3 ·4
I
3 2 OU15 14
(")
I+COU~NT+I f3
I~ COUNT UP
·I~ COUNT DOWN .I~ INHIBIT COUNTING.J
::D ASYNC SYNC SYNC
(") CLEAR CLEAR lOAD
c
=i
en
1283
2-392 TEXAS
INSTRUMENTS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS568A, SN54ALS569A . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS568A, SN74ALS569A . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , - 65 °e to 1 59 °e

UNIT
VIL Low-level input voltge 0.8 0.8 C
Q outputs -1 -2.6
IOH High-level output current mA
CCO and RCO -0.4 -0.4
Q outputs 12 24
CCO and RCO 4 8
'ALS568A 0 18 0 20
'ALS569A 0 25 0 30
.A:i;:CR or lOAD low 20 15
CLK high 27.5 25
tw Pulse duration
'AlS568A
ClK low 27.5 25 ns en
'AlS569A
ClK high 20 16.5 t:
ClK low 20 16.5 ::J
Data at A, B, C, D 25 20 U
ENP, ENT
High 35 30 a:
low 25 20 U
SClR
low 20 15
en
tsu. Setup time before ClK t High (inactive)
low
35
20
30
15
ns
«
lOAD
High (inactive) 35 30 c
UfD 35 30 2:
AClR inactive 10 10 «
th Hold time after ClKt for any input 0 0 ns en
...I
«
1283
TEXAS 2-393
INSTRUMENTS
PARAMETER TEST CONDITIONS SN54AlS569A SN74AlS569A UNIT
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1.5 V
All outputs Vee = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2
Vee = 4.5 v. IOH = -1 rnA 2.4 3.3 V
VOH Q outputs
Vee = 4.5 V. IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V. IOl = 12 rnA 0.25 0.4 0.25 0.4
Q outputs
Vee = 4.5 V. IOl = 24 rnA 0.35 0.5
VOL V
Vee = 4.5 V. IOH = 4 rnA 0.25 0.4 0.25 0.4
ceo and ReO
Vee = 4.5 V. IOl = 8 rnA 0.35 0.5
IOZH Vee = 5.5 V. Vo = 2.7 V 20 20 p.A
IOZl Vee = 5.5 V. Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A
III Vee = 5.5 V. VI = 0.4 V -0.2 -0.2 rnA
ceo and ReO -15 -70 -15 -70
IOi Vee = 5.5 V. Vo = 2.25 V rnA
Q outputs -30 -112 -30 -112
..

tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS .
»
r-
en
»
2
C
»
en
n
::D
n
c
=i
en
1283
2-394 TEXAS
INSTRUMENTS
SYNCHRONOUS 4-BIT UP/DOWN DECADE AND BINARY COUNTERS
Vee = 4.5 V to 5.5 V,

el = 50 pF,
R1 = 500 Q,
FROM TO R2 = 500 Q,
PARAMETER UNIT
MIN MAX MIN MAX
'AlS568A 18 20
f max MHz
'AlS569A 25 30
tpLH 4 17 4 13
ClK Any Q ns
tPHl 7 18 7 16
tpLH 12 31 12 28
ClK RCO ns
tpHl 10 22 10 19
tpLH 5 15 5 13
ClK CCO ns
tpHl 6 30 6 25
tPLH 9 25 9 23
ui5 RCO
9 23 9 19
ns
tpHL
tPLH 6 17 6 15
ENT RCO ns
tpHl 4 17 4 13
tplH 5 15 5 13
ENT CCO ns
tpHl 9 28 9 23
tplH 4 14 4 12
ENP CCO ns
tpHl 5 17 5 14
tpHl AClR Any Q 9 22 9 20 ns
tpZH 6 21 6 18
CJ)
G Any Q ns
tpZl 6 29 6 24
1 !::
tpHZ
G Any Q
1 12 10
ns =»
tplZ 3 19 3 13
u
NOTE 1: For load circuit and voltage waveforms, see page 1·12 .. a:
u
CJ)
<t
C
2
<t
CJ)
..J
<t
1283
TEXAS 2-395
INSTRUMENTS
lEI
»
r-
VJ
»
:2
c
»VJ
("')
::D
("')
c
=i
VJ
2-396
SN
• 3-State Buffer-Type Outputs Drive Bus-Lines Directly SN74ALS573. SN74AS573 •.. N PACKAGE
(TOP VIEW)
o Choice of True or Inverting Logic oc Vee
10 1Q
'ALS573, 'AS573 True Outputs 2Q
'ALS5BO, 'AS5BO Inverting Outputs 3Q
4Q
• Package Options Include Both Plastic and Ceramic 50 5Q
Chip Carriers in Addition to Plastic and Ceramic DIPs 60 6Q
7Q
description
These 8-bit latches feature three-state outputs designed SN54ALS573. SN54AS573 ..• FH PACKAGE
specifically for driving highly capacitive or relatively low- SN74ALS573. SN74AS573 .•• FN PACKAGE
impedance loads. They are particularly suitable for implementing (TOP VIEW)
buffer registers, I/O ports, bidirectional bus drivers, and working
registers.
The eight latches are transparent D-type latches. While the 20

enable (C) is high the outputs (Q or 0) will respond to the data (D) 30
inputs. When the enable is taken low the outputs will be latched 40
to retain the data that was set up. 50
60
A buffered output-control input can be used to place the eight
outputs in either a normal logic state (high or low logic levels) or a OOUdd
CDZ CDr--
high-impedance state. In the high-impedance state the outputs t9
neither load nor drive the bus lines significantly. The high-
impedance state and increased drive provide the capability to
drive the bus lines in a bus-organized system without need for
SN54ALS580, SN54AS580 .•. J PACKAGE
en
interface Or pull-up components.
SN74ALS580, SN74AS580 ... N PACKAGE
(TOP VIEW)
!:::
:l
The output control (DC) does not affect the internal operation of Vee CJ
the latches. Old data can be retained or new data can be entered 10 a:
while the outputs are at high impedance. 2(1
30 CJ
The SN54ALS573, SN54AS573, SN54ALS580 and 45 en
SN54AS580 are characterized for operation over the full military 55
65 «
temperature range of - 55°C to 125°C. The SN74ALS573,
SN74AS573, SN74ALS580, and SN74AS580 are character-
75 c
8(1 2
ized for operation from 0 °C to 70°C.
SN54ALS580, SN54AS580 ... FH PACKAGE

«
en
SN74ALS580,SN74AS580 ... FNPACKAGE -J
(TOP VIEW) «
3D 20
40 35
50 40
60 55
70 60
00 Uldld
CDZ CDr--
t9

1283
TEXAS 2-397
INSTRUMENTS
POST OFFICE BOX 225012. DALLAS. TEXAS 75265
FUNCTION TABLES
'ALS573, 'AS573 'ALS580, 'AS580
(EACH LATCH) (EACH LATCH)
INPUTS INPUTS
OUTPUT OUTPUT
ENABLE ENABLE
a Q
oc C D oc C D
L H H H L H H L
L H L L L H L H
L L X 00 L L X 50
H X X Z H X X Z
logic symbols
'ALS573, 'AS573 'ALS580, 'AS580
(19) 10
10 10
20
3D (4)
:~~: 20
30
20
3D
40 (5) (16) 40
40
50 (6) (15) 50
50
60 (7) (14) 60
60
70 (8) (T3) 70 70
80 (9) (12) 80 (9)
80
116 logic diagram (positive logic)

'ALS573, 'AS573 'ALS580, 'AS5ao
:t>
r-
en
:t> 10"':':':'--+--1
2
C
:t>
en
C')
::D
C') 4a
c 40"":':':--+-1
=i
en sa sa
6a
60-=--4--l 60
70
70-=--+--1 70
SO
SO....:..:..:----l
1283
2-398 TEXAS
INSTRUMENTS
TYPES SN54ALS573. SN54ALS580. SN74ALS573. SN74ALS580

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . . 7 V
SN74ALS573,SN74ALS580 .. : . . . . . . . . . . . . . . . . . . . . Qoet070oe
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50 °e
IOH High-level output current -1 - 2.6 rnA
Pulse duration, enable e high

I 'ALS573 10 10
tw ns
I 'ALS580 15 15
tsu Setup time, data before enable e 1- 10 10 ns
Hold time, data after enable e 1-

I 'ALS573 7 7
th ns
J 'ALS580 10 10
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) . .
PARAMETER TEST CONDITIONS SN54ALS580
MIN Typt MAX
SN74ALS580
MIN Typt MAX
UNIT
!::
:::)
-18 rnA -1.5 -1.5 V
u
Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA Vee- 2 Vee- 2 a:
= 4.5 IOH = -1 rnA
VOH Vee
Vee = 4.5
V,
V, IOH = -2.6 rnA
2.4 3.3
2.4 3.2
V
u
Vee = 4.5 V, 10L = 12 rnA 0.25 0.4 0.25 0.4 en
VOL
Vee = 4.5 V, IOL = 24 rnA 0.35 0.5
V
«
10ZH Vee
Vee
= 5.5
= 5.5
V,
V,
Vo = 2.7 V
Vo = 0.4 V, -20
20 20
-20
p,A
p,A
c
10ZL 2:
II
IIH
Vee
Vee
=
=
5.5 V,
5.5 V,
VI = 7 V
VI = 2.7 V
0.1
20
0.1
20
rnA
p,A
«
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA en
..J
10+ Vee = 5.5 V, Vo = 2.25 V
Outputs high
-15
10
-70
17
-15
10
-70
17
rnA
«
'ALS573 Outputs low 15 24 15 24
lee Vee = 5.5 V rnA
'ALS580 Outputs low 15 24 15 24

1283
TEXAS 2-399
INSTRUMENTS
'ALS573 switching characteristics (see Note 1)
Vee = 4.5 V to 5.5 V,

eL = 50 pF,
B1 = 500 Q,
FROM TO
(INPUT! (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 15 2 14
0 Q ns
tpHL 2 15 2 14
tPLH 8 27 8 20
C Q ns
tPHL 8 20 8 19
tpZH 4 21 4 18
5C Q ns
tpZL 4 21 '4 18
tpHZ 2 10 2 8
OC Q ns
tpLZ 3 15 3 13
..
Vee = 4.5 V to 5.5 V,
eL = 50 pF,
R1 = 500 Q,
FROM TO
(lNPUTI (OUTPUT)
TA ;= MIN to MAX
»
r-
MIN
3
MAX
21
MIN
3
MAX
18
rJ) tPLH
D 6 ns
tpHL 3 15 3 14
»
2
tpLH
tPHL
C Q 8
8
29
22
8
8
22
21
ns
C tpZH
DC Q 4 21 4 18
ns
»
rJ)
tpZL
tpHZ
DC 6
4
2
21
10
4
2
18
8
ns
tpLZ 3 15 3 13
n
::D
n NOTE 1: For load circuit and voltage waveforms. see page 1-12.
C
::::j
rJ)
1283
2-400 TEXAS
INSTRUMENTS
OCTAL D·TYPE TRANSPARENT LATCEHS WITH 3·STATE OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , ...... 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS573, SN54AS580 . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS573,SN74AS580 . . . . . . . . . . . . . . . . . . . . . . . . . 00eto70oe

SN54AS573 SN74AS573
IOl Low-level output current 32 48 mA

I 'AS573 5.5 4.5
ns
tw
I 'AS580 3 2
tsu Setup time, data before enable et 2 2 ns
th Hold time, data after enable e t 3 3 ns
SN54AS573 SN74AS573
PARAMETER TEST CONDITIONS SN54AS580
MIN Typt
SN74AS580
Typt MAX
UNIT
en
VIK Vee = 4.5 V, II = -18 mA
MAX
-1.2
MIN
-1.2 V
!::
Vee = 4,5 V to 5.5 V, IOH = -2 mA Vee- 2 Vee- 2
::>
(.)
VOH Vee = 4,5 V, IOH = -12 mA 2.4 3.2 V
a:
Vee = 4.5 V, IOH = -15 mA 2.4 3,3
(.)
Vee = 4,5 V, IOL = 32 mA 0.28 0,5
VOL
Vee = 4,5 V, IOL = 48 mA 0.33 0,5
V
en
IOZH Vee = 5,5 V, Vo = 2,7 V 50 50 /lA «
IOZl
II
Vee
Vee
=
=
5,5 V,
5.5 V,
Vo = 0.4 V
VI = 7 V
-50
0.1
-50
0.1
/lA
mA
c
:2
IIH
IlL
Vee
Vee
=
=
5.5 V,
5,5 V,
VI = 2.7 V
VI = 0.4 V
20
-0.5
20
-0.5
/lA
mA
«
lot Vee = 5,5 V, Vo = 2,25 V -30 -112 -30 -112 mA en
..oJ
'AS573
Outputs high
Outputs low
56
55
93
90
56
55
93
90
«
lee Vee = 5.5 V mA
'AS580 Outputs low , 65 106 65 106

1283
TEXAS 2-401
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 O.
PARAMETER UNIT
TA = MIN to MAX
SN54AS573 SN74AS573
MIN MAX MIN MAX
tpLH 3 9 3 6
0 Q ns
tpHL 3 7 3 6
tpLH 6 14 6 11.5
C Q ns
tpHL 4 9 4 7.5
tpZH 2 8 2 6.5
5C Q ns
tpZL 4 11 4 9.5
tPHZ 2 8 2 6.5
5C Q ns
tpLZ 2 8 2 7

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO Rl = 500 O.
PARAMETER UNIT
TA = MIN to MAX
SN54AS580 SN74AS580
MIN MAX MIN MAX
tPLH 3 10 3 7.5
0 Q ns
tpHL 3 7.5 3 7
tpLH 5 12 5 9
C Q ns
tpHL 4 8.5 4 8
tpZH 2 7.5 2 6.5
OC Q ns
tpZL 4 10.5 4 9.5
tpHZ 2 7.5 2 6.5
OC Q ns
tpLZ 2 8 2 7
1283
2-402 TEXAS
INSTRUMENTS
SN74ALS574~SN74ALS575, SN74AS574,SN74AS575
02661. JUNE 1982-REVISEO OECEM8ER 1983
• 3·State Buffer· Type Noninverting Outputs Drive SN54ALS574. SN54AS574 ..• J PACKAGE
Bus-Lines Directly SN74ALS574. SN74AS574 ••. N PACKAGE
(TOP VIEW)
oc 20 VCC
o Buffered Control Inputs 10 19 10
20 3 18 20
• 'ALS575 and 'AS575 Have Synchronous Clear 30 17 30
40 16 40
• Package Options Include Both Plastic and Ceramic 50 6 15 50
Chip Carriers in Addition to Plastic and Ceramic DIPs 60 14 60
70 13 70
o Dependable Texas Instruments Quality and Reliability 80 9 12 80
GNO 10 11 ClK
description SN54ALS574. SN54AS574 .•. FH PACKAGE

SN74ALS574. SN74AS574 ... FN PACKAGE
These 8-bit registers feature three-state outputs designed
(TOP VIEW)
specifically for bus driving. They are particularly ,suitable for
implementing buffer registers. I/O ports. bidirectional bus drivers, u
and working registers.
~ elg ~~
3 2 1 20 19
The eight edge-triggered D-type flip-flops enter data on the low-
to-high transition of the clock. The' ALS575 and' AS575 may be
synchronously cleared by taking the CLR input low.
The output-control does not affect the internal operation of the

flip-flops. Old data can be retained or new data can be entered
while the outputs are in the high-impedance state.
The SN54ALS' and SN54AS' devices are characterized for SN54ALS575.SN54AS575 ..• JTPACKAGE
operation over the full military temperature range of - 55 °C to SN74ALS575. SN74AS575 ... NT PACKAGE
(TOP VIEW)
125 °C. The SN74ALS' and SN74AS' devices are characterized
for operation from 0 °C to 70 o C. ClR 24 VCC en
oc 23 NC
10
!::
10 3 22
::>
20
30
4 21
20
20
30 u
'ALS574, 'AS574
FUNCTION TABLES
'ALS575, 'AS575
40 19 40 a::
(EACH FLIP-FLOP) (EACH FLIP-FLOP)
50
60
18
17
50
60 u
70
80
9
10
16
15
70
80 en
OC CLK 0 Q OC CLR CLK 0 Q NC
GNO
11 14 ClK
NC
<t
L t H H L L t X L 12 13
L t L L L H t H H
C
SN54ALS575, SN54AS575 .•• FH PACKAGE 2
L
H
L
X
X
X
QO
Z
L
L
H
H
t
L
L
X
L
00
SN74ALS575, SN74AS575 ... FN PACKAGE <t
H X X X Z en
-I
<t
20 5 25 20
30 6 24 30
40 7 23 40
NC 22 NC
50 21 50
60 10 20 60
70 11 19 70
Copyright © 1982 by Texas Instruments Incorpor,ated

1283
TEXAS 2-403
INSTRUMENTS
POST OFFICE 80X 225012 • OALLAS, TEXAS 75265
logic symbols
'AlS574, 'AS574 'AlS575, 'AS575
oc
ClK
elK
CIA
10 (22) 10
10
(4) (21) 20
20 20
(5) (20) 30
3D 3D
(6) (19) 40
40 40
(7) (18) 50
50 50
(8) (17) 60
60
(9) (16) 70
70 70
(10) (15) 80
SO 80
'AlS574, 'AS574 'AlS575, 'AS575
OC ,;.;;(2;.;.)_ _ _ _ _q
1m
l>
r-
en 20(3)
10 (3)
l>
:2 30(4)
C 20 (4)
l>
en 40(5)
3D (5)
~ (6)
::%J 50
n 40 (6)
c
=i 60(7)
en 50 (7)
70(8)
(8)
60
80(9)
(9)
70
Pin numbers shown are for J and N packages. Pin numbers shown are for JT and NT packages.
1283
2-404 TEXAS
INSTRUMENTS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS574, SN54ALS575 . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS574,·SN74ALS575 . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150°C
UNIT
'AlS574 0 30 0 35
'AlS575 0 25 0 30
'AlS574 elK high or low 16.5 14
'AlS575 elK high or low 20 16.5
Data 15 15
Setup time
tsu
before elK t 'AlS575
IelR high 20 20 ns
lelR low 15 15
Hold time Data 4 0
th ns
after elK t 'AlS575 lelR 0 0 en
TA Operating free-air temperature -55 125 0 70 °e !::
::::>
u
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) c:
SN54ALS574 SN74ALS574 u
en
VIK Vee = 4.5 V, II = -18 mA
MIN Typt MAX
-1.5
MIN Typt MAX
-1.5 V
«
Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vee- 2 Vee- 2 o
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V :2
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2 «
VOL
Vee
Vee
=
=
4.5 V,
4.5 V,
10l = 12 mA
10l = 24 mA
0.25 0.4 0.25
0.35
0.4
0.5
V en
...I
10ZH Vee
Vee
=
=
5.5 V,
5.5 V,
Vo = 2.7 V
Vo = 0.4 V
20
-20
20
-20
p.A
p.A
«
10Zl
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
III Vee = 5.5 V, VI = 0.4 V -0.2 -0.2 inA
10+ Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA
I Output high 10 17 10 17
tAli typical values are at Vee = 5 v, TA = 25°e.

1283
TEXAS 2-405
INSTRUMENlS

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
Rl = 5000,
FROM TO R2 = 5000,
PARAMETER UNIT
MIN MAX MIN MAX
f max 'ALS574 30 35
MHz
'AlS575 25 30
tplH 4 15 4 14
elK Any Q ns
tpHL 4 15 4 14
tpZH 4 21 4 18
oe Any Q ns
tpZl 4 21 4 18
Any Q 'AlS574 2 10 2 8
tpHZ
oe Any Q 'AlS575 2 12 2 10 ns
tpLZ Any Q 3 15 3 13
o flip·f1op signal conventions
-.J It is TI practice to name the outputs and other inputs of a Ootype flip-flop and to draw its logic symbol based on the
assumption of true data (0) inputs. Then outputs that produce data in phase with the data inputs are called Q and those
producing complementary data are called Q. An input that causes a Q output to go high or a Q output to go low is called
»
r-
en
»
2
In some applications it may be advantageous to redesignate the data input is. In that case all the other inputs and
C
»
en
Q PRE (5)
Q ClR
Q
::x:J ClK Cl ClK Cl
n i5
c (6)
Q
PRE
(6) Q
=i
en
Notice that Q and Q exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (~l on PRE and CLR remain since these inputs are still active-low, but that the presence or absence of the
polarity indicator changes at D, Q, and Q. Of course pin 5 ICi) is still in phase with the data input 15, but now both are
1283
2-406 TEXAS
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS574, SN54AS575 . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS574,SN74AS575 . . . . . . . . . . . . . . . . . . . . . . . . . OOeto700e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 6 5 °e to 1 50 °e

SN54AS574 SN74AS574
SN54AS575 SN74AS575
UNIT
ClK high 5 4
ClK low 3 2
Setup time Data 3 2
tsu ns
before ClKt 'AS575 I ClR high or low 6.5 5.5
Hold time Data 3 2
th ns
after ClKt 'AlS575 I ClR 0 0
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) (J)
SN54AS574 SN74AS574 t::

PARAMETER TEST CONDITIONS SN54AS575 SN74AS575 UNIT :::>
MIN Typt MAX MIN Typt MAX u
VIK VCC = 4.5 V, II =
-18 mA -1.2 -1.2 V
a:
VCC = 4.5 V to 5.5 V, IOH = -2 mA vCC- 2 VCC-2 U
VOH VCC = 4.5 V, IOH = -12 mA 2.4 3.2 V (J)
VCC
VCC
= 4.5 V,
= 4.5 V,
IOH = -15 mA
IOl = 32 mA 0.29 0.5
2.4 3.3
<t
VOL
VCC = 4.5 V, IOl = 48 mA 0.34 0.5
V c
IOZH Vce = 5.5 V, Vo = 2.7 V 50 50 p.A 2
IOZl Vce = 5.5 V, Vo = 0.4 V -50 -50 p.A <t
II VCC = 5.5 V, VI = 7 V 0.1 0.1 mA (J)
IIH VCC = 5.5 V, VI = 2.7 V 20 20 p.A ..oJ
OC, ClK, ClR -0.5 -0.5 <t
IlL Vce = 5.5 V, VI = 0.4 V -3 -2
mA
D
loi VCC'" 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
'ASS74 Outputs low 85 134 85 134
lec VCC = 5.5 V
mA
'AS575 Outputs low 88 142 88 142

typical values are at V CC = 5 V, T A = 25°C.

t All
*T~e output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
1283
TEXAS 2-407
INSTRUMENTS
/


Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
R1 = 500 O.
FROM TO R2 = 500 O.
PARAMETER UNIT
SN54AS574 SN74AS574
SN54AS575 SN74AS575
MIN MAX MIN MAX
f max 100 125 MHz
tpLH 3 11 3 8
elK Any Q
4 11 4
ns
tPHL 9
tpZH 2 7 2 6
oe Any Q
3 11 3
ns
tpZL 10
tpHZ 2 7 2 6
oe Any Q
2 7 2
ns
tpLZ 6
16
l>
r-
tn
l>
z
C
l>
tn
n
:IJ
n
c
=i
tn
1283
2-408 TEXAS
INSTRUMENTS
02661. DECEMBER 19B2 - REVISED DECEMBER 19B3
• 3-State Buffer-Type Inverting Outputs Drive Bus-Lines

SN54ALS576. SN54AS576 , , , J PACKAGE
DirecJly
SN74ALS576. SN74AS576 • • • N PACKAGE
(TOPVIEWI
DC 1 U20 VCC
• Buffered Control Inputs 10 19 10
20 18 20
• 'ALS577 and 'AS577 Have Synchronous Clear 3D 17 30
• Package Options Include Both Plastic and Ceramic 40 16 40
50 15 50
Chip Carriers in Addition to Plastic and Ceramic DIPs 60 7 14 60
'. Dependa~le Texas Instruments Quality and Reliability
70 13 70
80 12 BO
GNO 10 11 ClK
description
SN54ALS576. SN54AS576 , •• FH PACKAGE
These 8-bit registers feature three-state outputs designed SN74ALS576. SN74AS576 . . , FN PACKAGE
(TOP VIEWI
specifically for bus driving. They are particularly suitable for
implementing buffer registers, I/O ports, bidirectional bus drivers, u
and working registers. ~ ~Ig ~I~
3 2 1 2019
The eight-bit edge-triggered Ootype flip-flops enter data on the
3D 4 20
low-to-high transition of the clock. 40 30
50 40
The output control does not affect the internal operation of the SO
60
flip-flops. Old data can be retained or new data can be entered 70 60
while the outputs are off. 9 10111213
The SN54ALS' and SN54AS" devices are characterized for

SN54ALS577. SN54AS577 , , , JT PACKAGE
1 25°C. The SN74ALS' and SN74AS' devices are characterized
SN74ALS577. SN74AS577 .• , NT PACKAGE
for operation from OOC to 70°C. (TOP VIEWI
VCC
en
FUNCTION TABLES NC !::
10 ::)
20 (.)
AlS576.AS576
lEach Flip-Flop)
30
40
a:
INPUTS OUTPUT 50 (.)
OC ClK D a 60
en
L
L
t
t
H
L
L
H
70
80. «
L L X 00 __
.........
ClK
.- NC c
z
H X X Z SN54ALS577. SN54AS577 , , . FH PACKAGE
SN74ALS577. SN74AS577 , . , FN PACKAGE «
(TOPVIEWI
en
-I
ALS577. AS577
lEach Flip-Flop)
~Igld ~ ~~I~
4 3 2 1 282726
«
INPUTS OUTPUT 20 20
OC CLR ClK D Q 3D 30
L L t X H 40 40
NC NC
L H t H L
50 50:
L H t L H 60 10 60
L H L X 00 70 11 70
H X X X Z 12 1314151617 18
~ ~ ~ ~ ~ dig

1283
TEXAS 2-409
INSTRUMENTS
logic symbols
'ALS576, 'AS576 'ALS577, 'AS577
ClK
ClK
ill
10 10
20 20
30 30
40 40
50 50
60
70
80
'ALS576, 'AS576 'ALS577. 'AS577

oc III _
OC
(2)
CLK _1_11.;..1-DC>' eLK 1141

-Ill
CLR
121 1191 10. 1221

10--'----+-~ (3) 10
10
III 20 131 1181

20 20 (4)
1211
20
l>
r 3D 141 1171 (20)
tJ) 30
3D
151 30
l>
2 40 (51 (16)
40 (6) (19)
40
C 40
l> 60 (6) (16)

171
11S1
tJ) 50
50 60
n 1141 1171
60 171
:lJ 60
60
IS) 60
n
c 1131 1161
=i
tJ)
70 (8)
io 70
191 70
80 191 1121 1101 (15) SO

80 SO--~
Pin numbers shown are for J and N packages. Pin numbers shown are for JT and NT packages.
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . • . . . . . . 7 V
Operating free-air temperature range: SN54ALS', SN54AS' . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS', SN74AS' ....... : ......•............. 0 °e to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. ..... 65 °e to 150°C
1283
2-410 TEXAS
INSTRUMENTS
. POST OFFICE BOX 225012 • DALLAS. TEXAS 75265

UNIT
'AlS576 0 25 0 30
'AlS577 0 25 0 30
elK high or low' AlS576 20 16.5
elK high or low 'AlS577 20 16.5
tsu ns
before elKt elR ('AlS577) 15 15
Hold time Data 4 0
th ns
after elKt ClR ('AlS577) 4 0
PARAMETER TEST CONDITIONS SN54ALS577 SN74AlS577 UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VCC = 4.5 V to 5.5 V, 10H = -0.4 mA vee- 2 vee- 2
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2 en
VOL
Vee
Vee
=
=
4.5 V,
4.5 V
10l = 12 mA
10l = 24 mA
0.25 0.4
0.35 0.5
V !:::
:J
10ZH Vee = 5.5 V, Vo = 2.7V 20 20 JlA (J
10Zl Vee = 5.5 V, Vo = 0.4 V -20 -20 JlA a:
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
(J
IIH Vee = 5.5 V, VI = 2.7 V 20 20 JlA
III Vee = 5.5 V, VI = 0.4 V -0.2 -0.2 mA en
loi: Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA cd:
=
I Outputs high 10 17 10 17 c
lee Vee 5.5 V L Outputs low 15 24 15 24 mA 2
I Outputs disabled 16 27 16 27 <C
t All typical values are at Vee 5 v, T A 25 ae.
= =
tThe output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output curr~nt, lOS' en
.....
cd:
1283
.TEXAS 2-411
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 5000,
FROM TO R2 = 5000,
PARAMETER UNIT
MIN MAX MIN MAX
'AlS576 25 30
f max MHz
'AlS577 25 30
tplH 4 15 4 14
elK Anya ns
tpHl 4 15 4 14
tpZH 4 21 4 18
OC Any Q ns
tpZL 4 21 4 18
Any Q AlS576 2 10 2 8
tpHZ
Dc Any Q AlS577 2 12 2 10 ns
tplZ Any Q 3 15 3 13
IIIfJ
»
r-
(J)
»
:2
C
»(J)
(")
:rJ
(")
c
=i
(J)
1283
2-412 TEXAS
INSTRUMENTS

SN54AS576 SN74AS576
SN54AS577 SN74AS571
UNIT
elK high 5 4
elK low 3 2
Setup time Data 3 2
tsu ns
before elKt elR ('AS5771 6.5 5.5
Hold time Data 3 2
th ns
after elKt elR ('AS5771 0 0
SN54AS576 SN74AS576
VIK Vee =
4.5 V, II = -18 mA -1.2 -1.2 V
Vee =
4.5 V to 5.5 V, IOH = -2 mA VCC- 2 VCC-2
VOH Vee - 4.5 V, IOH - -12 mA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 mA 2.4 3.3
Vee = 4.5 V, IOl = 32 mA 0.29 0.5 CI)
VOL V
Vee = 4.5 V IOl = 48 mA 0.33 0.5
!:::
IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 /LA :::>
IOZl Vee = 5.5 V, Vo = 0.4 V -50 -50 /LA u
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA a:
IIH
0
Vee = 5.5 V, VI = 2.7 V 20
-3
20
-2
/LA
u
III Vee = 5.5 V, VI = 0.4 V mA CI)
All other -0.5 -0.5
lo~ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA <t
Outputs high 77 125 77 125 C
'AS576 Outputs low 84 135 84 135 Z
lee Vee = 5.5 V
Outputs disabled
Outputs high
84
78
135
126
84
78
135
126
mA <t
CI)
'AS577 Outputs low 76 123 76 123 ...J
<t
t All typical values are at Vee ; 5 V, T A ; 25 ae.
1283
TEXAS 2-413
IN~UMENTS
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS WITH 3-STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO R2 = 500 n.
PARAMETER UNIT
SN54AS576 SN74AS576
SN54AS577 SN74AS577
MIN MAX MIN MAX
f max 100 125 MHz
tplH 3 11 3 8
elK Any Q ns
tpHl 4 11 4 9
tpZH 2 7 2 6
OC Any Q ns
tpZL 3 11 3 10
tpHZ 2 7 2 6
OC Any Q ns
tPlZ 2 7 2 6
- »
r-
en
»
:2
c
»
en
("')
::Il
("')
c
=i
en
1283
2-414 TEXAS
INSfRUMENlS .
SN74ALS620A THRU SN74ALS623A, SN74AS620 THRU SN74AS623
OCTAL BUS TRANSCEIVERS
02661 .. DECEM8ER 1982-REVISED DECEM8ER 1983
• Bus Transceivers in High-Density 20-Pin DIP SN54ALS', SN54AS' ..• J PACKAGE

and the New Plastic and Ceramic Chip SN74ALS', SN74AS' .•. N PACKAGE
Carriers (TOP VIEW)
• Local Bus-Latch Capability GAB Vee

A1 GBA
• Choice of True or Inverting Logic
A2 B1
• Choice of 3-State or Open-Collector Outputs A3 B2
A4 B3
A5 B4
Reliability
A6 B5
A7 B6
DEVICE OUTPUT LOGIC
A8 B]
'ALS620A, 'AS620 3-State Inverting B8
'ALS621A, 'AS621 Open-Collector True
'ALS622A, 'AS622 Open-Collector Inverting
'ALS623A, 'AS623 3-State True SN54ALS', SN54AS' ... FH PACKAGE
SN74ALS', SN74AS' , •. FN PACKAGE
(TOP VIEW)
description
ID U <{
N.-<{UID
These octal bus· transceivers are designed for <{ <{ t!)> It!)
asynchronous two-way communication between data
buses. The control function implementation allows for
maximum flexibility in timing. A3 B1
A4 B2
These devices allow data transmission from A bus to A5 B3
the B bus or from the B bus to the A bus depending A6 B4
upon the logic levels at the enable inputs (G'BA and A7 B5
GAB).
The enable inputs can be used to disable the device

en
so that the buses are effectively isolated. t:
:)
The dual-enable configuration gives the octal bus (.)
transceivers the capability to store data by a::
simultaneous enabling of GBA and GAB. Each output reinforces its input in this transceiver configuration. Thus, when (.)
both control inputs are enabled and all other data sources to the two sets of bus lines are at high impedance, both
sets of bus lines (16 in all) will remain at their last states. The 8-bit codes appearing on the two sets of buses will
en
be identical for the' AlS621 A, 'AS621 and' AlS623A, , AS623 or complementary for the' ALS620A, 'AS620 and
<t
, AlS622A, , AS622. C
The -1 versions of the SN74ALS' parts are identical to their standard versions except that the recommended maximum
2:
tOl is increased to 48 mAo There are no -1 versions of the SN54ALS' parts.
<t
en
The SN54' family is characterized for operation over the full military temperature range of - 55 °e to 125°e. The ..J
SN74' family is characterized for operation from ooe to 70 o e. <t
FUNCTION TABLE
ENABLE INPUTS OPERATION

'ALS620A, 'ALS622A 'ALS621A, 'ALS623A
GBA GAB
'AS620, 'AS622 'AS621, 'AS623
L L B data to A bus B data to A bus
H H A data to B bus A data to B bus
H L Isolation Isolation
B data to A bus, B data to A bus,
L H
A data to B bus A data to B bus
TEXAS 2-415
INsrRuMENTS
TYPES SN54ALS620A THRU SN54ALS623A. SN54AS620 THRU SN54AS623
SN74ALS620A THRU SN74ALS623A. SN74AS620 THU SN74AS623
logic symbols
'ALS620A, 'AS620 'ALS621 A, 'AS621 'ALS622A, 'AS622 'ALS623A, 'AS623

'ALS620A, 'AS620 'ALS621A, 'AS621 'ALS622A, 'AS622 'ALS623A, 'AS623
_AI
»
r-
il"BA---oQ
GAB
Bl
GBA----01
GAB
AI BI
GBA----d
.GAB
AI Bl Bl
fJ)
»
:2
A2 B2 A2 B2 A2 B2 B2
C
»
fJ)
TO OTHER SIX
TRANSCEIVERS
TO OTHER SIX
TRANSCEIVERS
TO OTHER SIX
TRANSCEIVERS
TO OTHER SIX
TRANSCEIVERS
o
::XJ
o
c
=i
fJ)
1283
2-416 TEXAS
INSTRUMENTS
Supply voltage. Vee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Input voltage: All inputs ............................................................ " 7 V
110 ports .............................................................. 7 V
Operating free-air temperature range: SN54ALS620A. SN54ALS623A . . . . . . . . . . . . . .. - 55 °C to 125°ee
SN74ALS620A. SN74ALS623A .................... ooe to 70 0 e
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°e to 150 °e

12 24
48t
PARAMETER TEST CONDITIONS SN54ALS623A SN74ALS623A UNIT
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1.5 V en
Vee = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2 !::
Vee = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2
V
:J
VOH (.)
Vee = 4.5 V. IOH = -12 rnA 2
Vee = 4.5 V. IOH = -15 rnA 2 a:
Vee = 4.5 V. IOL = 12 rnA 0.25 0.4 0.25 0.4 (.)
Vee = 4.5 V. IOL = 24 rnA
VOL
(lOL = 48 rnA for -1 versions)
0.35 0.5
V
en
Control inputs Vee = 5.5 V. VI = 7 V 0.1 0.1
<t
II
A or 8 ports' Vee = 5.5 V. VI = 5.5 V 0.1 0.1
rnA c
Control inputs 20 20 2:
IIH
A or B ports§
Vee = 5.5 V. VI = 2.7V ",A <t
20 20
IlL
Control inputs
A or B ports§
Vee = 5.5 V. VI = 0.4 V
-0.1 -0.1
rnA en
...J
-0.1 -0.1
10' Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 rnA <t
Outputs hig h 24 39 24 34
'ALS620A Vee = 5.5 V Outputs low 31 49 31 44
ICC rnA
'ALS623A Vee = 5.5 V Outputs low 39 55 39 50
§For 110 ports. the parameters IIH and IlL include the off-state output current.
'The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
1283
TEXAS 2-417
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 O.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 12 2 10
A B ns
tpHL 2 12 2 10
tpLH 2 12 2 10
B A ns
tpHL 2 12 2 10
tpZH 3 23 3 17
GBA A ns
tpZL 5 31 5 25
tpHZ 2 14 2 12
GBA A ns
tpLZ 3 22 3 18
tpZH 3 23 3 18
GAB B ns
tpZL 5 31 5 25
tpHZ 2 14 2 12
GAB B ns
tpLZ 3 22 3 18
-
Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 O.
PARAMETER UNIT
l> (INPUT) (OUTPUT) R2 = 500 O.
r- TA = MIN to MAX
rJ) SN54ALS623A SN74ALS623A
l> MIN MAX MIN MAX

2 tPLH
A B
2 15 2 13
ns
C tpHL 3 13 3 11
tpLH 2 15 2 13
l> tPHL
B A
3 13 3 11
ns
rJ)
tpZH 5 25 5 22
(") GBA A ns
tpZL 5 25 5 22
:l2 tpHZ 2 19 2 16
GBA A ns
(") tPLZ 2 23 2 19
c tpZH
GAB B
5 25 5 22
ns
=t
rJ)
tpZL
tpHZ
5
2
25
19
5
2
22
16
GAB B ns
tPLZ 2 23 2 19
1283
2-418 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012 • DALLA~. TEXAS 75265
OCTAL BUS TRANSCEIVERS WITH OPEN·COLLECTOR OUTPUTS
Input voltage: All inputs and I/O ports ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS621A, SN54ALS622A ................. -55°C to 125°C
SN74ALS621A, SN74ALS622A ..................... ooe to ?OOe
Storage temperature range ........................................ '. . . . . . . . .. - 65°C to ·150 °e

Vec Supply voltage 4.5 5 5.5 4.5 5 5.5 V
12 24
10L Low-Iavel output current rnA
48t
The 48-mA limit applies for the SN74ALS621A·1 and SN74ALS622A·1 only.
MIN TYP:j: MAX MIN TYPi MAX
VIK Vec = 4.5 V,
Vce = 4.5 V,
II =
VOH = 5.5 V
-18 rnA -1.5
0.1
-1.5
0.1
V
rnA
en
10H
Vee = 4.5 V, 10L = .12 rnA 0.25 0.4 0.25 0.4
t::
::>
VOL Vee = 4.5 V, 10L = 24 rnA
0.35 0.5
V
u
0.1 0.1
a:
II
Control inputs
A or B ports
Vec = 5.5 V,
Vee = 5.5 V,
VI = 7 V
VI = 5.5 V 0.1 0.1
rnA u
IIH
Control inputs
Vee = 5.5 V, VI = 2.7 V
20 20
",A
en
A or B ports§ 20 20 cd:
IlL
A or B portS§
Vce = 5.5 V, VI = 0.4 V
-0.1 -0.1
rnA C
Z
'ALS621A Vce = 5.5 V Outputs low 35 53 35 48
cd:
ICC
'ALS622A Vec = 5.5 V
rnA
en
..oJ
Outputs low 20 33 20 28
cd:
iA11 typical values are at Vee = 5 V, TA = 25°C.
§For I/O ports, the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-419
INSTRUMENTS
TYPES SN54ALS621A, SN54ALS622A, SN74ALS621A, AN74ALS622A
OCTAL BUS TRANCEIVERS WITH OPEN·COLLECTOR OUTPUTS
'ALS621 A switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO RL = 680 Q.
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 10 45 10 33
A B ns
tPHL 5 24 5 20
tpLH 10 45 10 33
B A ns
tpHL 5 24 5 20
tPLH 10 47 10 39
GBA A ns
tpHL 12 40 12 35
tpLH 10 47 10 39
GAB B ns
tPHL 12 40 12 35
'ALS622A switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO RL = 680 n.
PARAMETER UNIT
-
MIN MAX MIN MAX
tpLH 8 42 B 35
A B ns
tpHL 5 23 5 19
»
r-
tpLH
tpHL
B A
8
5
42
23
8
5
35
19
ns
(Jl tpLH 8 45 8 38
»
:2
tpHL
tpLH
GBA A
10
8
40
45
10
8
35
38
ns
GAB B ns
C tpHL 10 40 10 35
»
(Jl
n
::JJ
n
c
=i
(Jl
1283
2-420 TEXAS
INSTRUMENTS
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
110 ports . . . . . . . . . . . . . . . . . . '.' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS620, SN54AS623 . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125°C
SN74AS620,SN74AS623 . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50°C

SN54AS620 SN74AS620
SN54AS620 SN74AS620
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 mA Vee- 2 Vee- 2
VOH
Vee = 4.5
= 4.5
V, IOH = -3mA 2.4 3.2 2.4 3.2
V. en
Vee
Vee = 4.5
V,
V,
IOH = -12 mA
IOH = -15 mA
2.4
2.4
!:::
:::l
Vee = 4.5 V, IOL = 48 mA 0.30 0.55
U
VOL V
Vee = 4.5 V, IOL = 64 mA 0.35 0.55 CC
Control inputs Vee = 5.5 V, VI = 7 V 0.1 0.1
II
A or B ports Vee = 5.5 V, VI = 5.5 V 0.1 0.1
mA U
Control inputs
= =
20 20 en
IIH
A or B ports t
Vee 5.5 V, VI 2.7V
50 50
jJA
<t
IlL
Control inputs
A or B ports t
Vee = 5.5 V, VI = 0.4 V
-0.5
-0.75
-0.5
-0.75
mA c
2
lo§ Vee = 5.5 V, Vo =
Outputs high
2.25 V -30
35
-112
57
-30
35
-112
57
mA
«
'AS620 Vee = 5.5 V Outputs low 74 122 74 122 en
...J
ICC
Outputs disabled
Outputs high
48
57
77 48
57
77
mA «
'AS623 Vee = 5.5 V Outputs low 116 116
tAli typical values are at VCC2 = 5 V, TA = 250C.

tFor 1/0 ports, the parameters IIH and IlL include the off·state output current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true Short-circuit output current, lOS'
1283 PRODUCT PREVIEW

This paga contains Information on a product under
development. TexaslnstrumenU reserves the right to TEXAS 2-421
OCTAL .BUS TRANSCEIVERS WITH 3·STATE OUTPUTS
,AS620 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
PARAMETER R2 = 500 Q. UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS620 SN74AS620
MIN MAX MIN MAX
tpLH 1 8 1 7
A B ns
tpHL 2 7 2 6
tPLH 1 8 1 7
B A ns
tpHL 2 7 2 6
tpZH 2 8.5 2 8
GBA A ns
tpZL 2 10 2 9
tpHZ 1 7.5 1 6
GBA A ns
tpLZ 2 15 2 12
tpZH 2 9 2 8
GAB B ns
tpZL 2 10.5 2 9
tPHZ 1 6.5 1 6
GAB B ns
tpLZ 2 16 2 13

VCC = 4.5 V to 5.5 V.
= 50 pF.
~
CL
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
:t> TA = MIN to MAX
en MIN TVPt MAX MIN TVPt .MAX
:t> tpLH
A B
5 5
ns
2 tpHL 5 5
C tPLH
B A
5 5
ns
tpHL 5 5
:t>
en tpZH
tpZL
GBA A
4
6
4
6
ns
("') tpHZ 4 4
GBA A ns
::IJ tpLZ 5 5
("') tpZH 5 5
GAB B ns
C tPZL 7 7
.~ tPHZ
GAB B
4 4
ns
en tpLZ 5 5

PRODUCT PREVIEW 1283
2-422
development. Taxaslnstruments reserve. the right to TEXAS
change or discontinue this product without notlca. INSTRUMENTS
POST OFFICE BOX 225012 '. DALLAS, TEXAS 75265
OCTAL BUS TRANSCEIVERS WITH OPEN-COLLECTOR OUTPUTS
Input voltage: All inputs and 1/0 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS621, SN54AS622 ........................ - 55°C to 125°C
SN74AS621,SN74AS622 . . . . . . . . . . . . . . . . . . . . . • . . . . OOCto70°C

SN54AS621 SN74AS621
SN54AS621 SN74AS621
VIK Vec = 4.5 V. II = -18 mA -1.2 -1.2 V
10H VCC = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
Vce = 4.5 V, 10L = 48 mA . 0.25 0.5
VOL V
VCC = 4.5 V. 10L = 64 mA 0.35 0.5 en
= 5.5 V. VI = 7 V
II
Control inputs
A or B ports
VCC
VCC = 5.5 V, VI = 5.5 V
0.1
0.1
0.1.
0.1
mA !::
::)
IIH
Control inputs
VCC = 5.5 V. VI = 2.7V
20 20
jlA u
A or B portst 20 20 a:
IlL
Control inputs
A or B portst
VCC = 5.5 V, VI = 0.4 V
-0.5
-0.5
-0.5
-0.5
mA u
Outputs high 48 79 48 79 en
Ice
'AS621 VCC = 5.5 V
Outputs low 116 189 116 189
mA
«
'AS622 Vce = 5.5 V Outputs high 25 25 c
Outputs low 62 62 z
t All typical valueS" are at Vee = 5 V. TA = 25°e
iFor I/O ports. the parameters IIH and IlL include the off-state output current.
«
en
...J
«

Thl. page contain. btfonnatlon on • product under
development. Tex.. Instrument. r...rve. the right to TEXAS 2-423
chenga or discontinue this product without notice. INSTRUMENTS
OCTAL BUS TRANSCEIVERS WITH OPEN·COLLECTOR OUTPUTS
I AS621 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
I
CL = 50 pF.
FROM TO RL = 680 n.
PARAMETER UNIT
SN54AS621 SN74AS621
MIN MAX MIN MAX
tpLH 5 28.5 5 24
A B ns
tpHL 1 8.5 1 7.5
tpLH 5 23 5 21
B A ns
tPHL 1 8.5 1 7.5
tpLH 5 24 5 21
GBA A ns
tpHL 1 10 1 9
tpLH 5 26 5 22
GAB B ns
tpHL 1 11 1 10

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 680 Q.
PARAMETER UNIT
SN54AS622 SN74AS622
~
tPLH 20 20
A B ns
tpHL 6 6
tpLH 20 20
B A ns
~ tpHL 6 6
r- tpLH
GBA A
22 22
ns
CJ) tpHL 8 8
~ tpLH
GAB B
23 23
ns
2 tpHL 9 9
C tAli typical values are at Vee = 5 V. TA = 25°e.
~
CJ)
("')
::x:J
("')
C
~
CJ)
2-424
This page contains Information on II product under
development. Toxaslnstruments r••• rves the rightto TEXAS
change or discontinue this product without notlc •. INSTRUMENTS
32·81T PARALLEL ERROR DETECTION AND CORRECTION CIRCUITS
02661, OECEMBER 1982 - REVISEO DECEMBER 1983
'ALS632, 'ALS633, •.. JD PACKAGE

• Detects and Corrects Single· Bit Errors
(TOP VIEW)
o Detects and Flags Dual-Bit Errors Vcc
LEOBO 52
• Built-In Diagnostic Capability MERR 51 Sl
ERR 50 SO
o Fast Write and Read Cycle Processing Times OBO 49 OB31
OBl 48 OB30
OB2 47 OB29
• Byte-Write Capability . . . 'ALS632 and 'ALS633 OB3 46 OB28
OB4 45 OB27
o Dependable Texas Instruments Quality and Reliability OB5 44 OB26
OEBO 10 OEB3
DEVICE PACKAGE BYTE-WRITE OUTPUT OB6 OB25
OB7 OB24
'ALS632 52-pin yes 3-State GNO GNO
'ALS633 52-pin yes Open-Collector OB8 OB23
'ALS634 48-pin no 3-State OB9 OB22
OEBl OEB2
'ALS635 48-pin no Open-Collector OB10 OB21
OB11 OB20
OB12 OB19
OB13 OB18
OB14 OB17
OB15 OB16
CB6 CBO
description CB5 CBl
CB4 CB2
The' ALS632 through' ALS635 devices are 32-bit parallel OECB CB3
error detection and correction circuits (EDACs) in 52-pin
('ALS632 and 'ALS633) or 48-pin ('ALS634 and 'ALS635),
600-mil packages. The EDACs use a modified Hamming
'ALS634, 'ALS635 .... JD PACKAGE
code to generate a 7-bit check word from a 32-bit data (TOP VIEW)
word. This cheek word is stored along with the data word
MERR VCC
during the memory write cycle. During the memory read
cycle, the 39-bit words from memory are processed by the
ERR
OBO
S1
SO
en
EDACs to determine if errors have occurred in memory. OBl
OB2
OB31
OB30
!::
OB3 OB29
::::l
Single-bit errors in the 32-bit data word are flagged and
OB4 OB28 CJ
corrected. OB5 OB27 a:
OEOB 9 OB26
Single-bit errors in the 7-bit check word are flagged, and OB6 10 OB25 - CJ
the CPU sends the EDAC through the correction cycle even OB7 11 38 OB24
en
though the 32-bit data word is not in error. The correction
cycle will simply pass along the original 32-bit data word
GNO
OB8
OB9
12
13
14
GNO
OB23
OB22
«
in this case and produce error syndrome bits to pinpoint the OB10 15 OB21 c
OBll OB20' z
error-generating location.
Dual-bit errors are flagged but not corrected. These errors

OB12
OB13
OB19
OB18 «
may occur in any two bits of the 39-bit word from memory
OB14
OB15
OB17
OB16
en
..oJ
(two errors in the 32-bit data word, two errors in the 7-bit
check word, or one er~or in each word). The gross-error
CB6
CB5
CB4
CBO
CBl
CB2
«
condition of all lows or all highs from memory will be OECB CB3
detected. Otherwise, errors in three or more bits of the
FOR CHIP CARRIER INFORMATION,
39-bit word are beyond the capabilities of these devices to
CONTACT THE FACTORY
detect.
Read-modify-write (byte-control) operations can be performed with the' ALS632 and' ALS633 EDACs by using output
latch enable, ITBBb, and the individual OEBO thru OEB3 byte control pins.
Diagnostics are performed on the EDACs by controls and internal paths that allow the user to read the contents of
the DB and CB input latches. These will determine if the failure occurred in memory or in the EDAC.
1283
TEXAS 2-425
INSTRUMENTS
TABLE 1 - WRITE CONTROL FUNCTION
DB CONTROL DB OUTPUT LATCH CB

MEMORY EDAC CONTROL ERROR FLAGS
DATA I/O OEBn OR (' ALS632,' ALS633) CHECK I/O CONTROL
CYCLE FUNCTION Sl SO ERR MERR
OEDB IEoBo OECB
Generate Output
'Write L L Input H X L H H
check word check bitst
tSee Table 2 for details on check bit generation.
memory write cycle details

During a memory write cycle, the check bits (CBO thru CB6) are generated internally in the EDAC by seven 16-input
parity generators using the 32-bit data word as defined in Table 2. These seven check bits are stored in memory along
with the original 32-bit data word. This 32-bit word will later be used in the memory read cycle for error detection
and correction.
TABLE 2 - PARITY ALGORITHM
CHECK WORD 32-BIT DATA WORD

BIT 31 3029282726252423 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
eBa X X X X X X X X X X X X X X X X
CBl X X X X X X X X X X X X X X X X
CB2 X X X X X X X X X X X X X X X X
l1li CB5
CB6
X X X X X X X X
X X X X X X X X
X X X X X X X X
X X X X X X X X
l> The seven check bits are parity bits derived from the matrix of data bits as indicated by "X" for each bit.
r-
en
error detection and correction details
l>
:2 During a memory read cycle, the 7-bit check word is retrieved along with the actual data. In order to be able to determine
C whether the data from memory is acceptable to use as presented to the bus, the error flags must be tested to determine
l> if they are at the high level.
en The first case in Table 3 represents the normal, no-error conditions. The EDAC presents highs on both flags. The next
Q two cases of single-bit errors give a high on MERR and a low on ERR, which is the signal for a correctable error, and
:lJ the EDAC should be sent through the correction cycle. The last three cases of double-bit errors will cause the EDAC
n to signal lows on both ERR and MERR, which is the interrupt indication for the CPU.
c
=i
en TABLE 3 - ERROR FUNCTION
Total Number of Errors Error Flags

Data Correction
32-Bit Data Word 7-Bit Check Word ERR MERR
0 a H H Not applicable
1 0 L H Correction
0 1 L H Correction
1 1 L L Interrupt
2 0 L L Interrupt
0 2 L L Interrupt
1283
2-426 TEXAS
INSTRUMENTS
Error detection is accomplished as the 7-bit check word and the 32-bit data word from memory are applied to internal
parity generators/checkers. If the parity of all seven groupings of data and check bits are correct, it is assumed that
no error has occurred and both error flags will be high.
If the parity of one or more of the check groups is incorrect, an error has occurred and the proper error flag or flags
will be set low. Any single error in the 32-bit data word will change the state of either three or five bits of the 7-bit
check word. Any single error in the 7-bit check word changes the state of only that one bit. In either case, the single
error flag (ERR) will be set low while the dual error flag (MERR) will remain high.
Any two-bit error will change the state of an even number of check bits. The two-bit error is not correctable since
the parity tree can only identify single-bit errors. Both error flags are set low when any two-bit error is detected.
Three or more simultaneous bit errors can cause the EDAC to believe that no error, a correctable error, or an uncorrectable
error has occurred and will produce erroneous results in all three cases. It should be noted that the gross-error conditions
of all lows and all highs will be detected.
TABLE 4 - READ. FLAG. AND CORRECT FUNCTION
DB CONTROL DB OUTPUT lATCH CB

MEMORY EDAC CONTROL ERROR FLAGS
DATA 1/0 OEBn OR (' AlS632,' AlS633) CHECK 1/0 CONTROL
CYCLE FUNCTION S1 SO ERR MERR
OEDB lEDBO OECB
Read Read & flag H l Input H X Input H Enabledt
latch input latched latched
Read data & check H H input H L input H Enabledt
bits data check word
Output Output Output
Read corrected data H H corrected L X syndrome L Enabledt
& syndrome bits data word bitst
tSee Table 3 for error description.

(J)
:1:See Table 5 for error location.
!::
As the corrected word is made available on the data 110 port (DBa thru DB31), the check word 110 port (CBO thru ::::>
CB6) presents a 7-bit syndrome error code. This syndrome error code can be used to locate the bad memory chip. u
See Table 5 for syndrome decoding. a:
u
(J)
«
c
2
«
(J)
..J
«
1283
TEXAS 2-427
INSTRUMENTS
32·BIT PARALLEL ERROR DETECTION AND CORRECTION CIRCUITS
TABLE 5 - SYNDROME DECODING
SYNDROME BITS SYNDROME BITS SYNDROME BITS SYNDROME BITS

ERROR ERROR ERROR ERROR
6 5 4 3 2 1 0 6 5 4 3 2 1 0 6 5 4 3 2 1 0 6 5 4 3 2 1 0
L L L L L L L unc L H L L L L L 2-bit H L L L L L L 2-bit H H L L L L L unc·
L L L L L L H 2-bit L H L L L L H unc H L L L L L H unc H H L L L L H 2-bit
L L L L L H L 2-bit L H L L L H L DB7 H L L L L H L unc H H L L L H L 2-bit
L L L L L H H unc L H L L L H H 2-bit H L L L L H H 2-bit H H L L L H H OB23
L L L L H L L 2-bit L H L L H L L OB6 H L L L H L L unc H H L L H L L 2-bit
L L L L H L H unc L H L L H L H 2-bit H L L L H L H 2-bit H H L L H L H OB22
L L L L H H L unc L H L L H H L 2-bit H L L L H H L 2-bit H H L L H H L OB21
L L L L H H H 2-bit L H L L H H H OB5 H L L L H H H unc H H L L H H H 2-bit
L L L H L L L 2-bit L H L H L L L OB4 H L L H L L L unc H H L H L L L 2-bit
L L L H L L H unc L H L H L L H 2-bit H L L H L L H 2·bit H H L H L L H OB20
L L L H L H L OB31 L H L H L H L 2-bit H L L H L H L 2-bit H H L H L H L OB19
L L L H L H H 2-bit L H L H L H H OB3 H L L H L H H OB15 H H L H L H H 2-bit
L L L H H L L unc L H L H H L L 2-bit H L L H H L L 2-bit H H L H H L L OB18
L L L H H L H 2-bit L H L H H L H OB2 H L L H H L H unc H H L H H L H 2-bit
L L L H H H L 2-bit L H L H H H L unc H L L H H H L OB14 H H L H H H L 2-bit
L L L H H H H OB30 L H L H H H H 2-bit H L L H H H H 2-bit H H L H H H H CB4
L L H L L L L 2-bit L H H L L L L OBO H L H L L L L unc H H H L L L L 2-bit
L L H L L L H unc L H H L L L H 2-bit H L H L L L H 2-bit H H H L L L H OB16
L L H L L H L OB29 L H H L L H L 2-bit H L H L L H L 2-bit H H H L L H L unc
L L H L L H H 2-bit L H H L L H H unc H L H L L H H OB13 H H H L L H H 2-bit
L L H L H L L OB28 L H H L H L L 2-bit H L H L H L L 2-bit H H H L H L L OB17
L L H L H L H 2-bit L H H L H L H OB1 H L H L H L H OB12 H H H L H L H 2-bit
L L H L H H L 2-bit L H H L H H L unc H L H L H H L OB11 H H H L H H L 2-bit
L L H L H H H OB27 L H H L H H H 2-bit H L H L H H H 2-bit H H H L H H H CB3
L L H H L L L OB26 L H H H L L L 2-bit H L H H L L L 2-bit H H H H L L L unc
L L H H L L H 2-bit L H H H L L H unc H L H H L L H OB10 H H H H L L H 2-bit
L L H H L H L 2-bit L H H H L H L unc H L H H L H L OB9 H H H H L H L 2-bit
L L H H L H H OB25 L H H H L H H 2-bit H L H H L H H 2-bit H H H H L H H CB2
L L H H H L L 2-bit L H H H H L L unc H L H H H L L OB8 H H H H H L L 2-bit
L L H H H L H OB24 L H H H H L H 2-bit H L H H H L H 2-bit H H H H H L H CB1
L L H H H H L unc L H H H H H L 2-bit H L H H H H L 2-bit H H H H H H L CBO
L L H H H H H 2-bit L H H H H H H CB6 H L H H H H H CB5 H H H H H H H none
CB X = error in check bit X

DB Y = error in data bit Y
2-bit = double-bit error
unc = uncorrectable multibit error
read-modify-write (byte control) operations

The' AlS632 and' AlS633 devices are capable of byte-write operations. The 39-bit word from memory must first
be latched into the DB and CB input latches. This is easily accomplished by switching from the read and flag mode
(Sl = H, SO = II to the latch input mode (Sl = H, SO = HI. The EDAC will then make any corrections, if necessary,
to the data word and place it at the input of the output data latch. This data word must then be latched into the output
data latch by taking lEDBO from a low to a high.
Byte control can now be employed on the data word through the OEBO through OEB3 controls. OEBO controls DBO-DB7
(byte 01, 0EB1 controls DB8-DB15 (byte 1I, OEB2 controls DB16-DB23 (byte 21, and 0EB3 controls DB24-DB31 (byte
31. Placing a high on the byte control will disable the output and the user can modify the byte. If a low is placed on
the byte control, then the original byte is allowed to pass onto the data bus unchanged. If the original data word is
altered through byte control, a new check word must be generated before it is written back into memory. This is
easily accomplished by taking control Sl and SO low. Table 6 lists the read-modify-write functions.
J2B3
2-428 TEXAS
INSTRUMENTS
32-81T PARALLEL ERROR DETECTION AND CORRECTION CIRCUITS
TABLE 6 - READ-MODIFY-WRITE FUNCTION
DB OUTPUT
MEMORY CONTROL CB ERROR FLAG
EDAC FUNCTION BYTEnt OEBnt LATCH CHECK 1/0
CYCLE 51 50 CONTROL ERR MERR
LEDBO
Read Read & Flag H L Input H X Input H Enabled
Latched Latched
Latch input data
Read H H Input H L input H Enabled
& check bits
data check word
Latched Hi-Z H
Latch corrected
output
r------
Output
-------
Read data word into H H H H Enabled
data Syndrome L
output latch /
word bits
Input
Modify appropriate modified H
Modify byte or bytes & BY TEO Output
L L ------- ------ H L H H
Iwrite generate new Output check word
check word unchanged L
BYTEO
tOEBO controls OBO-OB7 (BYTEO), OEB1 controls OB8-0B15 IBYTE1), OEB2 controls OB16-0B23 (BYTE2), OEB3 controls OB24-0B31 (BYTE3),
..
diagnostic operations
The' ALS632 thru 'ALS635 are capable of diagnostics that allow the user to deter'mine whether the Eo'AC or the
memory is failing_ The diagnostic function tables will help the user to see the possibilities for diagnostic control.
In the diagnostic mode (S 1 = L, SO = H), the checkword is latched into the input latch while the data input latch remains
transparent. This lets the user apply various data words against a fixed known checkword_ If the user applies a diagnostic
data word with an error in any bit location, the ERR flag should be low. If a diagnostic data word with two errors (J)
in any bit location is applied, the MERR flag should be low. After the checkword is latched into the input latch, it
!:::
can be verified by taking OECS low _This outputs the latched checkword. With the' ALS632 and' ALS633, the diagnostic :::>
data word can be latched into the output data latch and verified. It should be noted that the' ALS634 and' ALS635 u
do not have this pass-through capability because they do not contain an output data latch. Sy changing from the a:
diagnostic mode (S 1 = L, SO = H) to the correction mode (S 1 = H, SO = H), the user can verify that the EDAC will correct
U
the diagnostic data word. Also, the syndrome bits can be produced to verify that the EDAC pinpoints the error location.
Table 7 ('ALS632 and 'ALS633) and Table 8 ('ALS634 and 'ALS635) list the diagnostic functions .. (J)
«
c
2
«
(J)
-J
«
1283
TEXAS 2-429
INSTRUMENTS
32·811 PARALLEL ERROR DETECTION AND CORRECTION CIRCUITS
TABLE 7 - 'ALS632, 'ALS633 DIAGNOSTIC FUNCTION
DB BYTE DB OUTPUT CB
CONTROL ERROR FLAGS
EDAC FUNCTION DATA I/O CONTROL LATCH CHECK I/O CONTROL
S1 SO
OEBn
ERR M'ERR
LEDBO OECB
Input correct Input correct
Read & flag H L H X H H H
data word check bits
Latch input check
Input Latched
word while data
L H diagnostic H L input H Enabled
input latch remains
data word t check bits
transparent
Latch diagnostic Input Output latched
L
data word into
output latch
L H diagnostic
data word t
H H
r--------
' check bits
Hi-Z
--H---
Enabled
Latched Output
Latch diagnostic
input syndrome L
data word into H H H H Enabled
diagnostic bits
input latch
data word
1---------
Hi-Z H
Output
Output diagnostic Output
syndrome L
data word & H H diagnostic L H Enabled
syndrome bits data word 1--------
bits
Hi-Z
-----
H
Output corrected Output Output
diagnostic data corrected syndrome
-
L
H H L L Enabled
word & output diagnostic bits
syndrome bits data word
-------
Hi-Z
1-----
H
tDiagnostic data is a data word with an error in one bit location except when testing the 'M'E'RR error flag. In this case, the diagnostic data word will contain
errors in two bit locations.
l>
r-
en TABLE 8 - 'ALS634, 'ALS635 DIAGNOSTIC FUNCTION
l> CONTROL DB CONTROL DB CONTROL ERROR FLAGS
2 EDAC FUNCTION
S1 SO
DATA I/O
OEDB
CHECK I/O
OECB ERR MERR
C Input correct Input correct
Read & flag H L H H H H
l> data word check bits
en Latch input check
Input
'\"') bits while data Latched input
L H diagnostic H H Enabled
input latch remains check bits
::0 data word t
o transparent
c: Output input
L H
Input
diagnostic H
Output input
H Enabled
=4 check bits
data word t
check bits
CA Latch diagnostic Latched input Output
L
data into H H diagnostic H syndrome bits Enabled
input latch data word r--------- -------
Hi-Z H
Output corrected Output corrected Output
L
diagnostic H H diagnostic L syndrome bits Enabled
data word data word 1--------
Hi-Z
---H----
tDiagnostic data is a data word with an error in one bit location except when testing the MeRR error flag. In this case, the diagnostic data word will contain
errors in two bit locations.
1283
2-430 TEXAS
INSTRUMENlS
, ALS632, ,ALS633 logic diagram (positive logic)
DECODER
SYNDROME
X/Y
0
o ....
:,. ,. ~
I >1
J -
GENERATOR
=1
~
7
so - 1 3 , I h
1
S1 - 2 3 ~ CHECK·BIT
h
2- roo-- GENERATOR P- h
I"-.
LATCHES I"-.
~
I"-.
C BO-
,., 7L
,
- C1
10
7
, I"-.
CB6
- MUX ~ [7
~
BUFFERS U. . C GO 1~
a
32 7L
,
- --
X·OR]
...-
~
~
G1
CB
+*
: EN
~. . 0
7
ERROR
DETECTOR
- '---
LATCHES
C1
8 ""'- EN ERROR o--ER'R
DBO· DB7 10
DB8·D B15
8
10 ~ MULTI· en
DB16·D B23 u. 8, 10
7
' .. ERROR 0-- ME'RR
!::
~ ::::>
DB24·D B31 .. ,
A
8 ...
10 ua:
8 8 8 8 BUFFERS 32, ...
<l
u
BIT·IN·
BO : EN en
""'-
*
8 ...
-
ERROR
CORRECTOR
~
ERROR
DECODER «
B1 "- LATCHES =1 - EN c
z
-
~ -
* «
B2
-
"
,.,
~
32
-C C1
10 ... 32"
[32
32"
, ~
l en
....I
OE B3
- 8, ,. I
X·OR] «
LED BO
\
* 'ALS632 has 3-state (V') check-bit and data outputs.
'A LS633 has open-collector (<»
check-bit and data outputs.
1283
TEXAS 2-431
INSTRUMENTS
,ALS634, ,ALS635 logic diagram (positive logic)
DECODER
X/Y .O~---------------------tl
~ ~
SYNDROME
GENERATOR
o~ 7 J;;;'l . I 7. =1
so- 1 3 I ~
1 1------------, r---=::::::
Sl- 2 3" n CHECK·BIT
21- ~ GENERATOR ~
(See Table 2)
LATCHES
~
' - Cl
CBO· -41_----4...;.,;7,,,'--4 10 7
CB6 . .
"----
MUX
~
BUFFERS
r=::r-
K
-
GO
G1
32 7
, -
~ * "~~':...-r-4""--t ERROR
DETECTOR
0ECs -----<~:JI EN
(See Table 3)
"----
LATCHES
-- EN ERROR o--ffi
' - - - Cl
DBO.DB31 ~+-_...;:3~2,,--_ MULTI· 0 - - - -
, ...._+-..3....,2,,--
, "--11 D 7
, - ERROR MERR
32
32
BIT-IN·
ERROR ERROR
CORRECTOR DECODER
BUFFERS
<l
32
'---4---1* ,
OEDB------------~~~EN
[32
x·ORI
*'ALS634 has 3-state ('V) theck-blt and data outputs.

'ALS635 has open-collector (0) check-bit and data out~uts.
1283
2-432 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012·. DALLAS. TEXAS 75265
Supply voltage, Vee (see Note 1) ...................................................... 7 V
Input voltage: eB and DB ........................................................... 5.5 V
All others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature range: SN54ALS632 thru SN54ALS635 ............... , - 55 °e to 125°e
SN74ALS632 thru SN74ALS635. . . . . . . . . . . . . . . . . . .. aoc to 70 0 e
Storage temperature range .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 0 e

THRU THRU
UNIT
VII Low-level input voltage 0.8 0.8 V
ERR or MERR -0.4 -0.4
DB or CB I '
ALS632, •ALS634 -1 -2.6
ERR or MERR 4 8
DB or CB 12 24
..
tw Pulse duration LEDBO low 25 25 ns
(1) Data and check word before SOt
15 10
(51 =H)
(2) SO high before LED BOt (51 = H) t 45 45
(3) LEDBO high before the earlier
0 0
of SOl. or S1+ t
(4) LEDBO high before SH (SO=H) 0 0
en
I
tsu Setup time ns

(5) Diagnostic data word before S1t
(SO=H)
15 10
!::
(6) Diagnostic check word before
15 10
::>
the later of 51-1- or sot u
(7) Diagnostic data word before
25 20
a:
i:E'5'BOt (51 =L and SO=H)*
(8) Read-mode, SO low and 51 high 35 30
u
(9) Data and check word after en
sot (51 =H)
(10) Data word after 51 t (SO = H)
20 15
«
th Hold time
20 15
ns c
(11) Check word after the later
of 51.1. or sot
20 15 z
(1 2) Diagnostic data word after
0 0
«
Correction time (see Figure 1)
ITi5Bot (51 =L and SO=H)* en
...I
tcorr 65 58 ns
TA Operating free-air temperature -55 125 0 70 °C «
tThese times ensure that corrected data is saved in the output data latch.
tThese times ensure that the diagnostic data word is saved in the output data latch.
1283
TEXAS 2-433
INSTRUMENTS
32-81T PARALLEL ERROR DETECTION AND CORRECTION CIRCUITS
'ALS632, 'ALS634 electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
VIK Vee =
4.5 V, II = -18 rnA -1.5 -1.5 V
All outputs Vee =
4.5 V to 5.5 V, IOH = -0.4 rnA vee- 2 VCc-2
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
DB or eB
Vee = 4.5 V, IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V, IOL = 4 rnA 0.25 0.4 0.25 0.4
ERR or MERR
Vee = 4.5 V, IOL = 8 rnA 0.35 0.5
VOL V
Vee = 4.5 V, IOL = 12mA 0.25 0.4 0.25 0.4
DB or eB
Vee = 4.5 V, IOL = 24 rnA 0.35 0.5
SO or S1 Vee = 5.5 V, V, = 7 V 0.1 0.1
rnA
DB or eB Vee = 5.5 V, V, = 5.5 V 0.1 0.1
"
SO or S1 20 20
"H Vee = 5.5 V, V, = 2.7 V }LA
DB or eB~ 20 20
SO or S1 -0.4 -0.4
',L Vee = 5.5 V, V, = 0.4 V rnA
DB or eB~ -0.1 -0.1
IO§ Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
lee Vee =5.5 V, See Note 1 150 250 150 250 rnA
'ALS633, 'ALS635 electrical characteristics over recommended operating free-air temperature range (unless
~ otherwise noted)
l> MIN Typt MAX MIN Typt MAX
r- V,K Vee = 4.5 V, 'I = -18 rnA -1.5. -1.5 V
en VOH ERR or MERR Vee = 4.5 V to 5.5 V, IOH = -0.4 rnA VCC-2 Vec-2 V
l> IOH DB or eB Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
2 'ERR or 'jijjE"iffi'
Vee = 4.5 V, IOL = 4 rnA 0.25 0.4 0.25 0.4
C VOL
Vee = 4.5 V, IOL = 8 rnA 0.35 0.5
V
Vee = 4.5 V, IOL = 12 rnA 0.25 0.4 0.25 0.4
l> DB'or eB
en SO or S1
Vee = 4.5 V,
Vee = 5.5 V,
IOL =
24 rnA
V, = 7 V
0.35 0.5
rnA
.~ " DB or eB Vee = 5.5 V, V, = 5.5 V
::rJ SO or S1
o "H DB or eB~
Vee = 5.5 V, V, = 2.7V }LA
C SO or S1
Vee = 5.5 V, V, = 0.4 V rnA
IlL
~ DB or eB~
en IO§ ERR or MERR Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
lee Vee = 5.5 V, See Note 1 150 150 rnA
= 5 V, TA = 25°C.
t All typical values are at Vec
~For I/O ports lOA through 0H)' the parameters "H and ',L
include the off-state output current.
NOTE 1: ICC is measured with SO and 51 at 4.5 V and all CB and DB pins grounded.
PRODUCT PREVIEW 12B3
2-434
Thi. page conte In. information on a product under
development. Texa,'nstrument. reserve. the right to TEXAS
change or dl.contlnue thl. product without notlc•. INSTRUMENTS
'ALS632 switching characteristics, VCC 4.5 V to 5.5 V, CL 50 pF, TA MIN to MAX

(unlesss otherwise noted)
FROM TO SN54ALS632 SN74ALS632
(INPUT) (OUTPUT) MIN TYP MAX MIN TYP MAX
DB and CB ERR 51 =H. 50=L. RL=500 [1 10 43 10 40
tpd ns
DB ERR 51 =L. 50=H. RL=500 [1 10 43 10 40
DB and CB MERR 51 =H. 50=L. RL=500 [1 15 67 15 60
tpd ns
DB MERR 51 =L. 50=H. RL=500 [1 15 67 15 60
tpd 50~ and 51 ~ CB R1 =R2=500 [1 10 60 10 54 ns
tpd DB CB 51 = L. 50 = L. R1 = R2 - 500 [1 10 60 10 54 ns
tpd LEDBO~ DB 51 =X. 50=H. R1 =R2=500 [1 7 35 8 30 ns
tpd 51t CB 50=H. R1 =R2=500 [1 10 60 10 54 ns
ten OECB~ CB 50=H. 51 =X. R1 =R2=500 [1 5 30 7 25 ns
tdis OECBt CB 50=H. 51 =X. R1 =R2=500 [1 5 30 7 25 ns
ten OEBO thru OEB3 ~ DB 50=H. 51 =X. R1 =R2=500 [1 5 30 7 25 ns
tdis OEBO thru OEB3 t DB 50=H. 51 =X. R1 =R2= 500 [1 5 30 7 25 ns
'ALS633 switching characteristics, VCC 4.5 V to 5.5 V, CL 50 pF, TA MIN to MAX

(INPUT) (OUTPUT) MIN Typt MAX MIN Typt MAX
DB and CB ERR 51 = H. 50 = L. RL = 500 [1 26 26
tpd ns
DB ERR 51 =L. 50=H. RL=500 [1 26 26
51 =H. 50=L. RL=500 [1 40 40
tpd DB and CB MERR ns
50~ and 5H CB
51 =L. 50=H. RL =500 [1
RL=680 [1
40
40
40
40 ns
en
tpd
tpd DB CB 51 - L. 50 - L. RL - 680 [1 40 40 ns
!::
::;)
tpd LEDBO~ DB 51 =X. 50=H. RL=680 [1 26 26 ns
u
tpd 5lt CB 50=H. RL=680 [1 40 40 ns a:
tpLH
tpHL
OECBt
OECB~
CB
CB
51 =X. 50=H. RL =680 [1
51 =X. 50=H. RL=680 [1
24
24
24
24
ns
ns
u
OEBO thru OEB3t DB 51 =X. 50=H. RL=680 [1 24 24 ns
en
tPLH
tpHL OEBO thru OEB3 ~ DB 51 =X. 50=H. RL =680 [1 24 24 ns
<t
C
2
<t
en
...J
<t

development. Texas Instruments ....rves the right to TEXAS 2·435
cha,:,ge or discontinue this product without notice. INSTRUMENTS
'ALS634 switching characteristics, VCC = 4.5 V to 5.5 V, CL = 50 pF, TA MIN to MAX
o PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
TEST CONDITIONS
SN54ALS634
MIN TYpt MAX MIN
SN74ALS634
Typt MAX
UNIT
DB and CB ERR
S1 =H. SO=L. RL=500 n 26 26
ns
tpd
S1 =L. SO=H. RL=500 n 26 26
S1 =H. SO=L. RL=500 n 40 40
tpd DB and CB MERR ns
Sl =L. SO=H. RL=500!l 40 40
tpd SO~ and S1+ CB R1 =R2=500 n 35 35 ns
tpd DB CB Sl-L. SO-L. R1-R2-500 n 35 35 - ns
tpd S1t CB SO=H. R1 =R2=500!l 35 35 ns
ten OECB~ CB Sl =X. SO=H. R1 =R2=500!l 18 18 ns
tdis DECBt CB S1 =X. SO=H. R1 =R2=500!l 18 18 ns
ten OECB~ DB Sl =X. SO=H. R1 =R2=500 n 18 18 ns
tdis OECBt DB S1 =X. SO=H. R1 =R2=500!l 18 18 ns
'ALS635 switching characteristics, VCC = 4.5 V to 5.5 V, CL = 50 pF, TA = MIN to MAX

(INPUT) (OUTPUT) MIN TYpt MAX MIN Typt MAX
DB and CB ERR S1 =H. SO=L. RL =500!l 26 26
tpd ns
DB ERR S 1 ,;, L. SO = H. RL = 500 n 26 26
S1 =H. 50=L. RL =500!l 40 40
DB and CB MERR
-
tpd ns
S 1 = L. 50 = H. RL = 500 !l 40 40
tpd SO~ and 51+ CB RL =680!l 40 40 ns
tpd DB CB S 1 = L. SO = L. RL = 680 n 40 40 ns
tpd Slt DB SO =H. RL =680 !l 40 40 ns
tpLH DECBt CB S1 =X. SO=H. RL =680!l 24 24 ns
l>
r- tpHL OECB~ CB S1 =X. SO=H. RL =680!l 24 24 ns
o tpLH DEDBt DB S1 =X. SO=H. RL =680!l 24 24 ns
l> tpHL OEDB~ DB S1 =X. SO=H. RL=680 n 24 24 ns

2 t All typical values are at Vee = 5 V, TA = 25°e.
C
l>
o
o
-o
::D
c
=i
fA
2 -436
This page contllns information on a product under
development. Texas Instrument. resarv.s the ~ht to TEXAS
cheng. or discontinue thl. product without notlc•.
INSTRUMENlS
I4---READ---t1_~"""'---------CORRECT-----------+t_,
I I I
tf-'h(SI~ I
so-l ~i---------------------------------------------:i___________
SI------~t4~::::::::::~~o:rr~K:.~:n~::::::::::::+.I~--------------------------------
~.,u(1I~·h(91~ : r--'d;l~
DBO THRU DBJI -------~~:::J~~~'~~~'::~'~~~~::::::k'~~~~~~~~~~~~~~------
INPUT DATA WORD
I
OUTPUT CORRECTED DATA WORD
I+---'on--+l
OEBO THRU OEBJ
I :
I
~I __________________________________ ~
l+--'IU(II-+!4-'h(91-----+1
I , I
r- -tcIis - ~
CBOTHRUCM ______ ~:::!IN~P~UT~C~H~E~CK~W~O~R~D::::~~~~c:::::)(::~O~U~T~PU~T!S~YN~D~R~OM~E~C~O~D~E::~~~~~---
: t4--ten --..t
iI t - - - ' P d - - + j i
ERR W p /d'Nt,~LlD?0W'ffa~--------------V-A-L-ID.."E=R=R-FL-A-G---------------- }Wt0ZJk(,62/21 ....
if 'pd .,
MERR ~S~yj9~P'*~-----------V-A-LI-D=M=ER=R,...F-L-AG-------------....WJ(Jv'1d0%01
FIGURE 1-READ, FLAG, AND CORRECT MODE SWITCHING WAVEFORMS
If-- 'h(SI---tt
so: ri-------------------------------------,I
/+--READ .,. CORRECT _I. WRITE
SI-.J : I
I ~,--------------------------
DBO THRU DB7
I
----<r~IN~p~UT:-D:-A~T':-t~WO':':R~D-MK:X »»)
OUTPUT CORRECTED DATA WORD
t
I
INPUT MODIFIED BYTE 0 en
I I
!:::
DBB THRU DB15 INPUT DATA WORD OUTPUT CORRECTED DATA WORD
:::>
u
DB16 THRU DB23 INPUT DATA WORD OUTPUT CORRECTED DATA WORD
a:
DB24 THRU DBJI INPUT DATA WORD OUTPUT CORRECTED DATA WORD u
I en
OEBO
~ ________________________________________~------------------------~r----
«
DEsl
c
z
~--------------------------------------------r_--------------------~r--- «
~--------------------------------------------r_--------------------~r----
i
I
14--'",(21--"" j4-.... (3I-to!
en
..J
iToBo '<:"'~:"':'~<:":~~~~~<:":,,"\:~~~~'<:"'~~~~\\
W
M//I//I/////I///I///II/14
M--, ----.!
«
~----------------------__T-----------~r----
CBOTHRU CB6 INPUT CHECK WORD OUTPUT SYNDROME CODE OUTPUT CHECK WORD
I
I+--'pd-+l
\~__________V~A_L~ID~E_R_R_F~LA_G__________~1
\~_______v~A~L~ID~M~E~R~R~F~LA~G~____ _J1
FIGURE 2-READ, CORRECT, MODIFY MODE SWITCHING WAVEFORMS
1283
TEXAS 2-437
INSTRUMENTS
so
!4- '.u(SI-+! L
SI : rl---------------------------------------
~-------------------+I------~I
I
I
If--'h(10l-+t
I I
OUTPUT DIAGNOSTIC
DBO THRU DB31 INPUT VALID DATA WORD INPUT DIAGNOSTIC DATA WORD
DATAWORO
ruO: I : I 'dis~
~~~~ ....------~!~------------------~!------~I~------~I~-------------------+i----________~r----
I 'su(7l-l!••--1.Mo'.I-1....!-'SU(41: /f-'pd+t
~: : rl--·,---------r!---------------;I
....------...:--------------------..!~---JI+__+_'h(121---+1 L -__________________
CBO
If-'SU(61-+-' h(11I-+! ! I..-'Pd 4
THRU OUTPUT VALID CHECK WORD OUTPUT SYNDROME CODE
CB6 ~I--~~~~-f~'~J~-----~1_____~-----J~-----------------------------~~I
I I 'di.-i+-+!
: I
l4--'pd----tj
:!--.Pd---*! ______________________________
I
r-_ .
EiiR - -;- - - ,VERIFY PROPER OPERATION OF ERR FLAG , VERIFY PROPER OPERATION OF ERR FLAG. FLAG SHOULD BE LOW
__-+-__~-J ~ _ _ _ 2!;.A.!:.~~~ !!.,E!!I.!!.H2. _ _ __ J WITH A DIAGNOSTIC DATA WORD WITH ASINGLE ERROR
__ ~'~ __ !I I4--- t p d --+t ________________________________ _
MeRii VERIFY PROPER OPERATION OF MERR FLAG VERIFY PROPER OPERATION OF MERR FLAG. FLAG SHOULD BE LOW
...._______--' \.. ___ ..!.."~:.S~O~L~ ~ '::.~'- _ _ _ .,' ~_ _ _ _ _W_IT_H_A_D_IA_G_N.;.O_ST_IC_D_A_T_A_WO_R_D_W_IT_H_A_D_O_U_B..
LE..:E.;.R_RO
..R
_______
FIGURE 3-DIAGNOSTIC MODE SWITCHING WAVEFORM
1283
2-438 TEXAS
INSTRUMENTS
• Bidirectional Bus Transceivers in High- SN54ALS', SN54AS' ••• J PACKAGE

Density 20-Pin Packages SN74ALS', SN74AS' •.• N PACKAGE
(TOP VIEW)
DIR ~CC
• A Bus Outputs are Open-Collector; B Bus
A1 G
Outputs are 3-State
A2 81
• Package Options Include Both Plastic and A3 82
Ceramic Chip Carriers in Addition to Plastic A4 83
and Ceramic DIPs ~A5 84
A6 85
A7 86
Reliability
A8 87
GND 88
description
These octal bus transceivers are designed for asyn-
SN54ALS', SN54AS' ••• FH PACKAGE
chronous two-way communication between open- SN74ALS', SN74AS' .•• FN PACKAGE
collector and 3-state buses. The devices transmit (TOP VIEW)
data from the A bus (open-collector) to the 8 bus
(3-state) or from the 8 bus to the A bus depending N..- ~ ~
upon the level at the direction control (DIR) input. The
«« 0 > It!)
enable input ((3) can be used to disable the device so
the buses are isolated. . A3 81
A4 82
DEVICE A OUTPUT B OUTPUT LOGIC
'ALS638A, 'AS638 Open-Collector 3-State Inverting A5 83
. 'ALS639A, 'AS639 Open-Collector 3-State True A6 84
A7 85
The -1 versions of the SN74ALS' parts are identical
to the standard versions except that recommended en
maximum of IOL is increased to 48 milliamperes. !=
There are no -1 versions of the SN54ALS' parts. ::>
The SN54' family is characterized for operation over u
the full military temperature range of - 55°C to FUNCTION TABLE a:
125°C. The SN74' family is characterized for opera- CONTROL OPERATION .U
tion from 0 °C to 70 o C. INPUTS 'ALS638A 'ALS639A en
G OIR 'AS638 'AS639 <C
L H A data to B bus A data to B bus
C
H X Isolation Isolation
2
<C
en
...J
<C
TEXAS 2-439
INSTRUMENTS
TYPES SN54ALS638A. SN54ALS639A. SN54AS638. SN54AS639
SN74ALS638A. SN74ALS639A. SN74AS638. SN74AS639
logic symbols functional block diagrams (positive logic)

'ALS638A, 'AS638 'ALS638A, 'AS638
G ----~----------
-----+--'
OIR - - - -.....
A1 B1
A2 ...-~-- B2
TO SIX OTHER TRANSCEIVERS
'ALS639A, 'AS639 'ALS639A, 'AS639
-
G ---~-------~
»
r-
OIR ---~---....---
en A1 .-+--- B1
»
2
C
»
en A2 _-+--- B2
n
::D
n TO SIX OTHER TRANSCEIVERS
c
=t
1283
2-440 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEX~S 75265
A bus 110 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
8 bus 110 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range:SN54ALS638A, SN54ALS639A . . . . . . . . . . . . . . . . .. - 55 °e to 125 °e
SN74ALS638A, SN74ALS639A ...................... ooe to70oe

VOH High-level output voltage A ports 5.5 5.5 V
10H High-level output current B ports -12 -15 mA
12 24
10L Low-level output current A or B ports mA
48t
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) ...
PARAMETER TEST CONDITIONS SN54ALS639A SN74ALS639A UNIT en
MIN TYP; MAX MIN TYP; MAX !=
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V ::>
10H A ports Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 mA ua:
Vee - 4.5 V to 5.5 V, 10H - -0.4 mA Vee- 2 Vee- 2
VOH B ports
Vee = 4.5 V,
Vee = 4.5 V,
10H - -3 mA
10H = -12 mA
2.4
2
3.2 2.4 3.2
V u
Vee - 4.5 V, 10H - -15 mA 2
en
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
<t
VOL A or B ports Vee = 4.5 V, 10l = 24 mA
0.35 0.5
V C
(IOl = 48 rnA for -1 versions) Z
II
mA
<t
en
Control inputs 20 20 ...J
= 5.5 V, VI = 2.7V Il A
IIH
A or B ports§
Vee
20 20 <t
III Vee = 5.5 V, VI = 0.4 V rnA
A or B ports§ -0.1 -0.1
10' B ports Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
ICC Vee = 5.5 V rnA
*AII typical values are at Vee = 5 V. TA = 25°e
§ For 1/0 ports, the parameters IIH and IlL include the off-state output current.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
1283
TEXAS 2-441
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF,
RL = 680 n (A outputs),
FROM TO
PARAMETER R1 = R2 = 500 n (B outputs), UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tPLH 2 15 2 12
A B ns
tPHL 2 15 2 12
tpLH 8 30 8 25
B A ns
tpHL 8 35 8 30
tpLH 5 30 5 25
IT A ns
tpHL 10 50 10 45
tPZH 5 25 5 20
IT B ns
tpZL 5 28 5 22
tpHZ 2 12 2 10
IT B ns
tpLZ 3 18 3 15

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
RL = 680 n (A outputs),
FROM TO
PARAMETER R1 = R2 = 500 n (B outputs), UNIT
-.J (INPUT) (OUTPUT)

TA =
SN54ALS639A
MIN to MAX
SN74ALS639A
:t>
r- tpLH
MIN
2
MAX
15
MIN
2
MAX
12
A B ns
CA tpHL 2 15 2 12
10 35 10 30
:t> tpLH
tpHL
B A
5 28 5 22
ns
2 10 35 10 30
tPLH
C tpHL
G A
10 40 10 35
ns
:t> tpZH
G B
6 28 6 21
ns
CA tpZL 8 30 8 25
C') tpHZ 2 12 2 10
IT B ns
tpLZ 3 19 3 16
::Jl
C') NOTE 1: For load circuit and voltage waveforms, see page 1-12.
C
=i
CA
1283
2-442 TEXAS
INSTRUMENlS
POST OFFICE BOX 225012-. DALLAS. TEXAS 75265
TYPES SN54AS63B. SN54AS639. SN74AS63B. SN74AS639
A bus I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
B bus I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS638, SN54AS639 . . . . . . . . . . . . . . . . . . . . . . - 55°e to 1 25 °e
SN74AS638,SN74AS639 . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe

SN54AS638 SN74AS638
VOH High-level output voltage I A ports 5.5 5.5 V
IOH High-level output current I B ports -12 -15 rnA
IOL Low-level output current I A or B ports 48 64 rnA
SN54AS638 SN74AS638
= 4.5 V, (J)
VIK Vee II = -18 rnA -1.2 -1.2 V
IOH A ports Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 rnA !::
Vee = 4.5 V. to 5.5 V. IOH = -2 rnA Vee- 2 Vee- 2 :::>
Vee = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2 u
VOH B ports
Vee = 4.5 V. IOH = -12 rnA 2.4
V a:
Vee = 4.5 V. IOH = -15 rnA 2.4 u
A or B ports
Vee = 4.5 V. IOL = 48 rnA 0.3 0.55 (J)
VOL V
Vee = 4.5 V. IOL = 64 rnA 0.35 0.55
Control inputs Vce = 5.5 V. VI = 7 V 0.1 0.1
cd:
II rnA
A or B ports Vce = 5.5 V. VI = 5.5 V 0.1 0.1 C
Control inputs 20 20 2
IIH Vce = 5.5 V. VI = 2.7 V ,..A
cd:
A or B ports:!: 50 50
Control inputs -0.5 -0.5 (J)
IlL Vce = 5.5 V. VI = 0.4 V rnA
A or B ports:!: -0.75 -0.75 ..J
IO§ VCC - 5.5 V. Vo - 2.25 V -30 - 1 12 -30 -112 rnA cd:
'AS638 Outputs low 75 122 75 122
ICC Vce = 5.5 V rnA
'AS639 Outputs low 95 154 95 154

*For I/O ports. the parameters IIH and IlL include the off·state output current.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS'
1283
TEXAS 2-443
INSTRUMENTS
•AS638 switching characteristics (see Note 1)
Vcc ~ 4.5 V to 5.5 V.

CL ~ 50 pF.
RL ~ 680 {} (A outputs).
FROM TO
PARAMETER R1 ~ R2 ~ .500 {} (8 outputs). UNIT
(INPUT) (OUTPUT)
TA ~ MIN to MAX
SN54AS638 SN74AS638
MIN MAX MIN MAX
tpLH 2 8. 2 7
A 8 ns
tpHL 2 7.5 2 6.5
tpLH 5 23 5 20
8 A ns
tpHL 2 8 2 7
tpLH 5 20 5 19
IT A ns
tpHL 2 10 2 9
tpZH 2 10 2 8
IT 8 ns
tpZL 2 12 2 10
tpHZ 2 8 2 7
G 8 ns
tpLZ 2 12 2 10
Vcc ~ 4.5 V to 5.5 V.

CL ~ 50 pF.
RL ~ 680 {} (A outputs).
FROM TO
PARAMETER R1 ~ R2 ~ 500 {} (8 outputs). UNIT
-.J (INPUT) (OUTPUT)
MIN
TA
SN54AS639
~ MIN to MAX
MAX
SN74AS639
MIN MAX
l>
r- tpLH
A 8
2 11 2 9.5
ns
CJ) tpHL 2 10.5 2 9
tpLH 5 25 5 22
l> tpHL
8 A
2 10 2 9
ns
2 5 23 21.5
tpLH 5
C G A ns
tpHL 2 12.5 2 11.5
l> tpZH
G 8
2 12 2 10.5
ns
CJ) 2 12 10.5
tpZL 2
C') tpHZ 2 7.5 2 7
IT 8 ns
tpLZ 2 12 2 10.5
:D
C') NOTE 1: For load circuit and voltage waveforms. see page 1-12.
c
=i
CJ)
1283
2-444 TEXAS
INSTRUMENTS
SN74ALS640A THRU SN74ALS645A. SN74AS640 THRU SN74AS645
• Bidirectional Bus Transceivers in High- SN54ALS'. SN54AS' •.. J PACKAGE

Density 20-Pin Packages SN74ALS·. SN74AS' ••• N PACKAGE
(TOP VIEW)
e Choico of Truo or Inverting Logic
DIR Vee
• Choice of 3-State or Open-Collector Outputs A1 G
• Package Options Include Both Plastic and A2 B1
Ceramic Chip Carriers in Addition to Plastic A3 B2
and Ceramic DIPs A4 B3
A5 B4
A6 B5
Reliability
A7 B6
A8 B7
DEVICE OUTPUT LOGIC
'ALS640A, 'AS640 3-State Inverting
GND B8
'ALS641A, 'AS641 Open-COllector True
'ALS642A, 'AS642 Open-Collector Inverting
'ALS643A, 'AS643 3-State True and Inverting SN54ALS'. SN54AS' ..• FH PACKAGE
'ALS644A, 'AS644 Open-COllector True and Inverting SN74ALS·. SN74AS' ..• FN PACKAGE
'ALS645A, 'AS645 3-State True
(TOP VIEW)
description
These octal bus transceivers are designed for asyn-
chronous two-way communication between data
buses. The devices transmit data from the A bus to B1
the B bus or from the B bus to the A bus depending A4 B2
upon the level at the direction control (DIR) input. The A5 83
enable input (G) can be used to disable the device so A6 84
the buses are effectively isolated. A7 85
The -1 versions of the SN74ALS' parts are identical en
to the standard versions except that the recommend- !::
ed maximum IOL is increased to 48 milliamperes. :::>
There are no -1 versions of the SN54ALS' parts. u
CC
the full military temperature range of - 55 °e to
u
125 °e. The SN74' family is characterized for opera- en
tion from 0 °e to 70 °e. ~
FUNCTION TABLE
c
2:
CONTROL OPERATION ~
INPUTS
G DIR
•ALS640A •• AS640
'ALS642A. 'AS642
•ALS641 A •• AS641
•ALS645A, •AS645
'ALS643A, 'AS643
•ALS644A, •AS644
en
..J
L L B data to A bus B data to A bus B data to A bus ~
L H A data to B bus A data to B bus A data to B bus
H X Isolation Isolation Isolation
TEXAS 2-445
INSfRUMENlS
SN74ALS640A THRU SN74ALS645A. SN74AS640 THRU SN74AS645
logic symbols
•ALS640A •• AS640 •ALS641 A •• AS641 •ALS642A •• AS642
Bl
B2
B3
85
B6
B7
B8
•ALS643A •• AS643 •ALS644A •• AS644 •ALS645A •• AS645
Bl
Al Bl
A2
A2
A3 B3
A3 B3
B4
A5 B5
A5 85
A6 B6
B6
A7 B7
B7
l> A8
r- A8 B8
B8
CJ)
l> functional block diagrams (positive logic)

•ALS640A •• AS640 ·ALS641A. 'AS641 •ALS642A •• AS642
2
C
l>
CJ) DIR --+----~ OIR --t-------' DIR ---f-------J
(")
:XI Al Bl Al Bl Al Bl
(")
C
~ TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS
CJ)
•ALS643A •• AS643 •ALS644A •• AS644 •ALS645A •• AS645
DIR --t------' DIR ---f-------J DIR _+___---l
Al Bl Al Bl Al Bl
TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS ,TO SEVEN OTHER TRANSCEIVERS
1283
2-446 TEXAS
INSTRUMENTS
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . ',' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS640A, SN54ALS643A, SN54ALS645A ....... - 55 °e to 125 °e
SN74ALS640A,SN74ALS643A,SN74ALS645A .......... OOeto70oe

12 24
48t
The 48-mA limit applies for the SN74ALS640A-1, SN74ALS643A-1, and SN74ALS645A-1 only.
SN54ALS' SN74ALS'
MIN TYPi MAX MIN TYPi MAX
-18 mA -1.5 -1.5 V (J)
Vee - 4.5 V to 5.5 V, 10H = -0.4 mA VCC-2 VCc-2 !:::
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2 :::>
VOH
Vee = 4.5 V, 10H = -12 mA 2
V
u
Vee = 4.5 V, 10H = -15 mA 2 a:
VOL
Vee = 4.5 V,
Vec = 4.5 V,
10L
10L
= 12 mA
= 24 mA
0.25 0.4 0.25 0.4
V
u
0.35 0.5 (J)
Hal = 48 mA for -1 versions)
Control inputs Vee = 5.5 V, VI =7V 0.1 0.1
<t
II mA
A or B ports Vee = 5.5 V, VI = 5.5 V 0.1 0.1 C
Control inputs
= 5.5 V, = 2.7V
20 20 2
IIH
A or B ports§
Vee VI
20 20
IlA
<t
Control inputs -0.1 -0.1 (J)
IlL Vec = 5.5 V. VI = 0.4 V mA
A or B ports§ -0.1 -0.1 ...J
10' Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA <t
ICC 'AlS643A Vee = 5.5 V Outputs low 33 47 33 45 mA
iAIl typical values are at Vee = 5 V, TA = 25°e
§ For I/O ports, the parameters IIH and IlL include the off-state output current.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
1283
TEXAS 2-447
INSTRUMENTS
, AlS640A switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q •.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 14 2 11
A or B BorA ns
tpHL 2 13 2 10
tpZH 5 25 5 21
G A or B ns
tpZL 8 27 8 24
tpHZ 2 12 2 10
G A or B ns
tpLZ 3 20 3 15
,AlS643A switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 15 2 13
A B ns
tpHL 2 13 2 11
tpLH 2 15 2 13
»r- tpHL
tpZH
B A
2
5
13
28
2
5
11
25
ns
C/) G A ns
tpZL 5 28 5 25
»
2
tpHZ
tpLZ
G A
2
3
12
22
2
3
10
17
ns
C tpZH
G B
5 28 5 25
ns
»
C/)
tpZL
tpHZ
G B
5
2
28
12
5
2
25
10
ns
tPLZ 3 22 3 17
(')
~ ,AlS645A switching characteristics (see Note 1)
C Vcc = 4.5 V to 5.5 V.

= 50 pF.
=i
C/)
CL
R1 = 500 Q.
FROM TO
(INPUT)' (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tPLH 3 15 3 10
A or B BorA ns
tpHL 3 13 3 10
tpZH 5 25 5 20
G A or B ns
tpZL 5 25 5 20
tpHZ 2 12 2 10
G A or B ns
tpLZ 4 18 4 15
NOTE 1: For load Circuit and voltage waveforms. see page 1-12,
1283
TEXAS
INSTRUMENTS
. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Input voltage: All inputs and lID ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; ......... 7 V
Operating free-air temperature range: SN54ALS641 A, SN54ALS642A, SN54ALS644A ....... - 55 DC to 125 DC
SN74ALS641A,SN74ALS642A,SN74ALS644A .......... ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50 DC

12 24
48t
tThe extended limits apply only if Vee is maintained between 4.75 and 5.25 V.
The 48-mA limit appliel; for the SN74ALS641 A-1, SN74ALS642A-1, and SN74ALS644A-1 only.
MIN TYP; MAX MIN TYP; MAX en
VIK VCC = 4.5 V, II = -18 rnA -1.5 -1.5 V !:::
IOH VCC = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA ~
VCC = 4.5 V, IOL = 12 rnA 0.25 0.4 0.25 0.4 u
VOL VCC = 4.5 V, IOL = 24 rnA
0.35 0.5
V a:
Control inputs
(lOL = 48 rnA for -1
VCC = 5.5 V,
versions)
VI =7V 0.1 0.1
u
II
VCC = 5.5 V, = 5.5 V rnA en
A or B ports
Control inputs
= 5.5
VI 0.1
20
0.1
20
«
IIH
A or B ports§
VCC V, VI = 2.7V 20 20
iJ A
c
Control inputs -0.1 -0.1 2
IlL
A or B ports§
VCC = 5.5 V, VI = 0.4 V -0.1 -0.1
rnA
«
'ALS641A
Outputs high
Outputs low
25 40 25 37
en
33 50 33 47 ....I
ICC 'ALS642A VCC = 5.5 V
Outputs high
Outputs low
8
18
15
28
8
18
15
28
rnA
«
'ALS644A
iAIi typical values are at Vee = 5 V, T A = 25 De
§ For I/O ports, the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-449
INSTRUMENTS
,ALS641 A switching characteristics (see Note 1)

Vee = 4.5 V to 5.5 V,
el = 50 pF,
FROM TO Rl = 680 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tPlH 5 30 5 25
A or B B or A ns
tpHl 3 23 3 18
tPlH 8 35 8 30
G A or B ns
tpHl 8 35 8 30
tplH 8 37 8 32
DIR A or B ns
tpHl 8 37 8 32
,ALS642A switching characteristics (see Note 1)

Vee = 4.5 V to 5.5 V,
el = 50 pF,
FROM TO Rl = 680 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tplH 10 35 10 30
A or B B or A ns
tpHL 5 25 5 22
tpLH 10 35 10 30
Gor DIR A or B ns
'tpHL 15 43 15 38
l> .ALS644A switching characteristics (see Note 1)

r-
fA Vee = 4.5 V to 5.5 V,
el = 50 pF,
l> FROM TO Rl = 680 Q,
:2 PARAMETER
(INPUT) (OUTPUT)
UNIT
TA = MIN to MAX
C
l> MIN MAX MIN MAX
fA tpLH 10 35 10 30
A B ns
(") tpHL 5 25 5 22
:Jl tpLH 10 35 10 30
B A ns
(") tpHL 5 23 5 21
C tPLH
G A
8 35 8 30
ns
~ tPHL 10 38 10 35
fA tpLH 8 31 8 26
G B ns
tPHL 15 40 15 35
tpLH 8 31 8 26
DIR A ns
tpHL 10 40 10 35
tpLH 10 35 10 30
DIR B ns
tpHL 15 40 15 35
NOTE 1: For load circuit and voltage waveforms. see page 1·12,
1283
2-450 TEXAS
INSTRUMENlS
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS640, SN54AS643, SN54AS645 ............ - 55 DC to 125 DC
SN74AS640,SN74AS643,SN74AS645 . . . . . . . . . . . . . . . . ODCto70 DC

SN54AS640 SN74AS640
SN54AS645 SN74AS645
SN54AS' SN74AS'
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2mA Vee- 2 Vee- 2
VOH
Vee = 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
V en
IOH = -12 mA
Vee = 4.5 V,
Vee = 4.5 V, 10H = -15 mA
2.4
2.4
!::
:::>
VOL
Vee = 4.5 V, 10L = 48 mA 0.30 0.55
V u
Vee = 4.5 V,
Vee = 5.5 V,
10l = 64 mA
VI = 7 V
0.35 0.55 a:
Control inputs 0.1 0.1
II
mA U
Control inputs 20 20 en
IIH
A or B portst
Vee = 5.5 V, VI = 2.7V
50 50
jAA
«
IlL
Control inputs
A or B portst
Vee = 5.5 V, VI = 0.4 V
-0.5
-0.75
-0.5
-0.75
mA c
2
lo§ Vee = 5.5 V, Vo = 2.25 V
Outputs high
-30
37
-112
58
-30
37
-112
58
mA
«
'AS640 Outputs low 78 123 78 123 en
..J
Outputs disabled
Outputs high
51
48
80
79
51
48
80
79
«
ICC 'AS643 Vee =5.5 V Outputs low 88 143 88 143 mA
'AS645 Outputs low 95. 149 95 149
*For 1/0 ports. the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-451
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS640 SN74AS640
MIN MAX MIN MAX
tpLH 2 8 2 7
Aor B BorA ns
tpHL 2 7 2 6
tpZH 2 10 2 8
G A or B ns
tpZL 2 12 2 10
tpHZ 2 9 2 8
G A or B ns
tpLZ 2 16 2 13

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS643 SN74AS643
MIN MAX MIN MAX
16
tPLH 2 10 2 8
A B ns
tpHL
tpLH
B A
2
2
7.5
11.5
2
2
7
10 .ns
l> tpHL 2 10 2 9
r- tpZH 2 13 2 11
en tpZL
G A
2 13 2 11
ns
l> tpHZ
G A
2 8.5 2 7.5
ns
2 tpLZ 2 12 2 10.5
C tpZH
G B
2 11.5 2 10
ns
tpZL 2 12 2 10
l>
en tpHZ
tpLZ
G B
2
2
8
12
2
2
7
10
ns
Q
::D ' AS645 switching characteristics (see Note 1)
(")
Vcc = 4.5 V to 5.5 V.
C
CL = 50 pF.
=t
en PARAMETER
FROM TO
Rl = 500 Q.
R2 = 500 Q. UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS645 SN74AS645
MIN MAX MIN MAX
tpLH 2 11 2 9.5
Aor B BorA ns
tPHL 2 10.5 2 9
tpZH 2 12 2 11
tpZL
IT A orB ns
2 12 2 10
tPHZ 2 8 2 7
IT A orB ns
tpLZ 2 13 2 12
NOTE 1: For load circuit and voltage waveforms. see page 1·12,
1283
2-452 TEXAS
INSTRUMENTS
Supply voltage, VCC .. ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V .
Operating free-air temperature range: SN54AS641, SN54AS642, SN54AS644 ............ - 55 DC to 1 25 DC
SN74AS641,SN74AS642,SN74AS644 . . . . . . . . . . . . . . . . ODCt070 DC

SN54AS641 SN74AS641
SN54AS644 SN74AS644
SN54AS641 SN74AS641
SN54AS644 SN74AS644
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA en
= 4.5 V, IOL = 48 rnA
VOL
Vee
Vee = 4.5 V, IOL = 64 rnA
0.3 0.55
0.35 0.55
V t:
:J
II
= 5.5 V, VI = 5.5 V
rnA U
A or B ports VCC 0.1 0.1 a:
IIH
A or B ports:t
VCC = 5.5 V, VI = 2.7V 50 50
iJ A U
Control inputs -0.5 -0.5 en
IlL
A or B ports:t
VCC = 5.5 V, VI = 0.4 V -0.75 -0.75
rnA
«
'AS641
Outputs high
Outputs low
50
84
82
136
50
84
82
136
c
2
ICC 'AS642 VCC = 5.5 V
Outputs high
Outputs low
25
64
42
104
25
64
42
104
rnA «
Outputs high 38 62 38 62 en
'AS644 ..J
t All typical values are at Vee = 5 V, TA = 25°e
«
*For 1/0 ports, the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-453
INSTRUMENTS
TYPES SN54AS64D THRU SN54AS645
SN74AS64D THRU SN74AS645

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF,
FROM TO Rl = 680 Q.
PARAMETER UNIT
SN54AS641 SN74AS641
MIN MAX MIN MAX
tplH 5 23 5 21
A or B BorA ns
tpHL 1 8.5 1 7.5
tpLH 5 24 5 21
G A or B ns
tpHL 1 10 1 9
tPLH 5 26 5 22
DIR A or B ns
tpHL 1 11 1 10

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF.
FROM TO Rl = 680 Q.
PARAMETER UNIT
SN54AS642 SN74AS642
MIN MAX MIN MAX
tpLH 5 28.5 5 24
Aor B BorA ns
tpHL 1 8.5 1 7.5
tpLH 5 25 5 22
G A or B ns
tpHL 1 11 1 10
tpLH 5 26.5 5 23.5
DIR Aor B ns
tPHL 1 12.5 1 11.5

VCC = 4.5 V to 5.5 V,
Cl = 50 pF.
FROM TO Rl = 680 Q.
PARAMETER UNIT
SN54AS644 SN74AS644
MIN MAX MIN MAX
tpLH 5 28.5 5 24
A B ns
tpHL 1 8.5 1 7.5
tpLH 5 23 5 21
B A ns
tpHL 1 8.5 1 7.5
tPLH 5 24 5 21
G Aor B ns
tpHL 1 10 1 9
tPLH 5 26 5 22
DIR .A or B ns
tPHL 1 11 1 10
NOTE 1: For load circuit and voltage waveforms, see page 1·1 2.
2·454
Thls page contains information on e product under
development. Texas Inltruments re.ervesthe right to TEXAS
chenge or discontinue this product without notice. INSTRUMENTS
TYPES SN54ALS646 THRU SN54ALS649, SN54AS646, SN54AS648
SN74ALS646 THRU SN74ALS649, SN74AS646, SN74AS648
OCTAL BUS TRANSCEIVERS AND REGISTERS
• Independent Registers for A and B Buses SN54ALS', SN54AS' ••. JT PACKAGE

SN74ALS', SN74AS' .•. NT PACKAGE
• Multiplexed Real-Time and Stored Data (TOP VIEW)
• Choice of True or Inverting Data Paths CAB Vce
• Choice of 3-State or Open-Collector Outputs SAB C6A
DIR S6A
• Included Among the Package Options Are
Compact 24-pin 300-mil Wide DIPs and
A1 G
A2 61
Both 28-pin Plastic and Ceramic Chip
A3 B2
Carriers
A4 63
• Dependable Texas Instruments Quality and A5 B4
Reliability A6 B5
A7 B6
DEVICE OUTPUT LOGIC A8 67
'ALS646, 'AS646 3-State True G.ND B8
'ALS647 Open-Collector True
'ALS648, 'AS648 3-State Inverting
SN54ALS', SN54AS' ••. FH PACKAGE
'ALS649 Open-Collector Inverting
SN74ALS', SN74AS' ••. FN PACKAGE
(TOP VIEW)
description
These devices consist of bus transceiver circuits with CI:~~U~~~
O(/)UZ>U(/)
3-state or open-collector outputs, D-type flip-flops,
and control circuitry arranged for multiplexed
transmission of data directly from the input bus or A1 G
from the internal registers. Data on the A or 6 bus will A2 B1
be clocked into the registers on the low-to-high tran- A3 B2
sition of the appropriate clock pin (CAB or C6A). The NC NC
following examples demonstrate the four fundamen- A4 B3 en
tal bus-management functions that can be performed A5 B4 t:
A6 B5 :::>
with the octal bus transceivers and registers.
12 131415161718 ua:
I'C:OOUC:Ol'CD
~~ZZOJOJOJ
(!) U
en
«
c
2
«
en
..J
«
~ ~ ~
1211 131 111 1231 121 1221 1211 131 III 1231 121 1221 1211 131 111 1231 121 1221 1211 131 111 1231 121 1221
(j OlA CAll CBA SAB SBA G CAB CBA SAB SBA G OIR CAB CBA SAB G OIR CAB CBA SAB SBA
L X X X L X X X t X X L X
H X
REAL-TIME TRANSFER TRANSFER

REAL-TIME TRANSFER STORAGE FROM
STORED DATA
BUS B TO BUS A BUS A TO BUS B A, B. OR A AND B
TO AOR B
TEXAS 2-455
INSTRUMENTS
TYPES SN54ALS646 THRU SN54ALS649. SN54AS646. SN54AS648
SN74ALS646 THRU SN74ALS649. SN74AS646. SN74AS649
OCTAL BUS TRANSCEIVE~S AND REGISTERS
Enable (0) and direction (DIR) pins are provided to control the transceiver functions. In the transceiver mode, data pre-
sent at the high-impedance port may be stored in either register or in both. The select controls (SAB and SBA) can
multiplex stored and real-time (transparent mode) data. The direction control determines which bus will receive data
when enable 0 is active (low). In the isolation mode (controlG high), A data may be stored in one register and/or B data
may be stored in the other register.
When an output function is disabled, the input function is still enabled and may be used to store and transmit data. On-
ly one of the two buses, A or B, may be driven at a time.
The -1 versions of the SN74ALS' parts are identical to the standard versions except that the recommended maximum
10L is increased to 48 milliamperes. There are no -1 versions of the SN54ALS' parts.
The SN54' family is characterized for operation over the full military temperature range of - 55°C to 125 DC. The
SN74' family is characterized for operation from 0 ° to 70 DC.
FUNCTION TABLE
INPUTS DATA I/O· OPERATION OR FUNCTION

'ALS646, 'ALS647 'ALS648, 'ALS649
G DIR CAB CBA SAB SBA A1 THRU A8 B1 THRU BB 'AS646 'AS648
X X t X X X Input Not specified Store A, B unspecified Store A, B unspecified
.X X X t X X Not specified Input Store B, A unspecified Store B, A unspecified
H X t t X X Store A and B Data Store A and B Data
Input Input
H X H or L H or L X X Isolation, hold storage Isolation, hold storage
L L X X X L Real-Time B Data to A Bus Real-Time B Data to A Bus
Output Input
L L X X X H Stored B Data to A Bus Stored B Data to A Bus
L H X X L X Real-Time A Data to B Bus Real-Time A Data to B Bus
~ ~
Input Output
L H X X H X Stored A Data to B Bus Stored A Data to B Bus
·The data output functions may be enabled or disabled by various signals at the and OlR inputs. Data input functions are always enabled. I.e .• data at the bus
»
r-
pins will be stored on every low-to-high transition on the clock inputs.
functional block diagrams (positive logic)

en
»2: 'ALS646, 'AS646, 'ALS647 'ALS648, 'AS648, 'ALS649
C
»
en
(1
::D
(1
C
~
en
., .,
TO 7 ontE.. CHANNELS
TO J OTHEltCHANNILI
Pin numbers shown are for JT and NT packages.
1283
2-456 . TEXAS
INSTRUMENTS
logic symbols
'ALS646, 'AS646 'ALS647
G (211 G (211
G3
DIR (31 DIR (31 3 ENI (BA)
3 EN2 (AB)
CBA (231 CBA (231 C4
SBA (221 SBA (221 G5
CAB (11· CAB (11 C6
SAB (21 SAB (71
(201 (201
(41 (41
Bl Bl
Al Al
(51 (191 (51 (191

A2 B2 A2 B2
(61 (181 (61 (181

A3 B3 A3 B3
(71 (171 (71 (171

A4 B4 A4 B4
(81 (161 (81 1161
AS B5 AS B5
(91 (151 (91 (151

A6 B6 A6 B6
(101' 1141 (101 (141
A7 B7 A7 B7
(111 1131 (Ill (131

A8 B8 A8 B8
'ALS648, 'AS648 'ALS649

DI
en
G (211
DIR (31
G3
G (211
DIR (31
G3 t::
3 ENI (BA) 3 ENI (BA( :::::>
3 EN2 (AB) 3 EN2 lAB)
U
CBA (231
SBA 1221 G5
C4 CBA 1231
SBA 1221
C4
G5
a::
CAB III C6 CAB III C6 U
SAB 121 SAB 121
(41
1201
(4)
1201 en
Al
Bl
Al
Bl
cd:
C
IS) (19) lSI 119) 2:
A2 B2 A2 B2
cd:
(6) (18) (6) 118)
A3 B3 A3 B3 en
(71 (17) (7) (17)
....I
A4 B4 A4 B4 cd:
(81 (16) (8) (16)
AS B5 A5 B5
(91 (IS) (9) (15)
A6 B6 A6 B6
(10) (141 (10) (14)
A7 B7 A7 B7
(111 (13) 1111 (13)
A8 B8 A8 B8
1283
TEXAS 2-457
INsrRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEXA~ 75265
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS
Input voltage: Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS646, SN54ALS648 ...................... - 55°C to 125°C
SN74ALS646,SN74ALS648 . . . . . . . . . . . . . . . . . . . . . . . . OOCto700C
Storage temperature range ...................... : . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C
Vce Supply voltage 4.5 5 5.5 4.5 5 5.5 V
12 24
48t
tw Pulse duration, clocks high or low ns
tsu Setup time, A before CAst or B before eBAt ns
th Hold time, A after CABt or B after CBAt I ns
tThe extended condition applies if Vee Is maintained between 4.75 V and 5.25 V.
The 48-mA limit applies for the SN74ALS646-1 and SN74ALS648-1 only.
1m electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
l> PARAMETER TEST CONDITIONS SN54ALS648 SN74ALS648 UNIT
r- MIN TYP* MAX MIN TYP* MAX
o VIK Vec = 4.5 V, II = -18 rnA -1.5 -.1.5 V
l> Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA Vec-2 Vee- 2
2 Vee = 4.5 V, 10H = -3 rnA 2.4 3.2 2.4 3.2
V
VOH
C Vee = 4.5 V, 10H = -12 rnA 2
Vee = 4.5 V, 10H = -15 rnA 2
l> = 4.5 V, 10L = 12 rnA
o VOL
Vee
Vec = 4.5 V, 10L = 24 rnA
0.25 0.4 0.25
0.35
0.4
0.5 V
(') (I0L = 48 rnA for -1 versions)
::0 Control inputs VCC = 5.5 V, VI = 7 V 0.1 0.1
(') II rnA
c: IIH
Control inputs
Vec = 5.5 V, VI = 2.7V
20 20
,..A
=i A or B ports§ 20 20
o IlL
Control inputs
Vee = 5.5 V, VI = 0.4 V
-0.1 -0.1
rnA
A or B ports§ -0.2 -0.2
10' Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
Outputs high 60 60
'ALS646 Outputs low 68 68
ICC Vee = 5.5 V rnA
Outputs high 52 52
*AII typical values are at Vee = 5 V, TA = 25°C
§For 1/0 ports, the parameters IIH and IlL include the off-state output current.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
Additional Information on these products can be obtaIned from the factory as It becomes available.
2 -4 5 8
ThIs page contain. Infonnatlon on • product unde,
development. Tex •• InlllrUmenta rel8t'V•• the right to TEXAS
chltng. 0' eIl.contlnue thI. product without notlc•• INSTRUMENTS
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3·STATE OUTPUTS
,ALS646 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
f max MHz
tpLH 11 11
CBA or CAB A or B ns
tpHL 13 13
tpLH 8 8
A or B BorA ns
tpHL 8 8
tpLH SBA or SABi 16 16
A or B ns
tpHL (with A or B high) 16 16
tpLH SBA or SABi 15 15
A or B ns
tpHL (with A or Blow) 12 12
tpZH 17 17
G A or B ns
tpZL 20 20
tpHZ 10 10
G A or B ns
tpLZ 12 12
tpZH 17 17
DIR A or B ns
tpZL 20 20
tpHZ 10 10
DIR A or B ns
tpLZ 12 12

Vcc - 4.5 V to 5.5 V. en
CL = 50 pF. I-
FROM TO
R1 = 500 Q. ::>
PARAMETER R2 = 500 Q. UNIT U
(INPUT) (OUTPUT)
TA = MIN to MAX a:
SN54ALS648 SN74ALS648 U
en
f max
tpLH 11 11
MHz
«
tpHL
CBA or CAB A or B
13 13
ns
c
2
tpLH
tpHL
A or B B or A
10
12
10
12
ns
«
tpLH SBA or SABi
A or B
16 16
ns en
tpHL (with A or B high) 16 16 ...J
tpLH SBA or SABi
A or B
15 15
ns
«
tpZH 17 17
G A or B ns
tpZL 20 20
tpHZ 10 10
G A or B ns
tpLZ 12 12
tpZH 17 17
DIR A or B ns
tpZL 20 20
tpHZ 10 10
DIR A or B ns
tpLZ 12 12
tAli typical values are at Vee = 5 V. T A = 25 DC.
~These parameters are measured with the internal output state of the storage register opposite to that of the bus input.

This pago contains information on a product under
development. Toxaslnstrumentl roserves tho right to TEXAS 2-459
chango or discontinue this product without notlca. INSTRUMENTS
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH OPEN·COLLECTOR OUTPUTS
~,:!I~~~~~:e: ~.C.C. : : : : : : : : : : : : : : : : : : : :' : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : ;~

Operating free-air temperature range: SN54ALS647, SN54ALS649 . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS647,SN74ALS649 . . . . . . . . . . . . . . . . . . . . . . . . 00Cto70°C

12 24
48t
tw Pulse duration, clocks high or low ns
tsu Setup time, A before CABt or B before CBAt ns
th Hold time, A after CABt or B after CBAt ns
tThe extended condition applies if Vee is maintained between 4.75 and 5.25 V.
VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V
IOH VCC = 4.5 V, VOH = 5.5 V 0.1 0.1 mA
VCC = 4.5 V, IOL = 12 mA 0.25 0.4
VOL VCC = 4.5 V, IOL = 24 mA 0.35 0.5 V
(lOL = 48 mA for -1 versions)
A or B ports VCC - 5.5 V, VI - 5.5 V 0.1 0.1
II mA
Control inputs VCC = 5.5 V, VI =7V 0.1 0.1
A or B ports§ 20 20
IIH
Control inputs
VCC = 5.5 V, VI = 2.7 V 20 20
IJA

IlL
A or B ports§
VCC = 5.5 V, VI = 0.4 V -0.2 -0.2
mA
Outputs high 52 52
'ALS647
Outputs low 62 62
ICC Vee = 5.5 V Outputs high 50 50
mA
'ALS649
Outputs low 60 60
*AII typical values are at Vee = 5 V, T A = 25 °e
Additional Information on these products can be obtained from the factory as It becomes available.
2-460
ThI. page contain. Information on • product under
development. Texellnmumenta ,...rv.. the right to TEXAS
change or dllconltnue thl. product without notice. INSTRUMENTS
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH OPEN·COLLECTOR OUTPUTS
,ALS64 7 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = G80 Q.
PARAMETER UNIT
f max MHz
tpLH 24 24
tpHL 15 15
tpLH 24 24
A or B BorA ns
tpHL 12 12
tpLH SBA or SAB; 26 26
A or B ns
tpLH SBA or SAB; 26 26
Aor B ns
tpLH 24 24
G A orB ns
tpHL 17 17
tpLH 24 24
DIR A or B ns
tpHL 17 17

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 680 Q.
PARAMETER UNIT
MIN
SN54ALS649
TVPt MAX
SN74ALS649
MIN TVPt MAX
....en
f max MHz :::;)
tpLH 24 24 u
tpHL
CBA or CAB A orB
15 15
ns a:
tpLH
A or B BorA
24 24
ns
u
tpHL 10 10
en
tpLH
tpHL
SBA or SAB;
(with A or B high)
A or B
26
15
26
15
ns «
tpLH SBA or SAB; 26 26 c
tpHL (with A or Blow)
A or B
15 15
ns
z
tpLH
IT A or B
24 24
ns
«
tpHL
tpLH
17
24
17
24
en
-I
tpHL
t All typical values are at V CC
DIR
= 5 V. T A = 25°C.
A or B
17 17
ns
«
t These parameters are measured with the internal output state of the storage register opposite to that of the bus input.
1283
TEXAS 2-461
INSTRUMENlS
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS
Input voltage: Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
1/0 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS646, SN54AS648 . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74AS646,SN74AS648 . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70 o C

SN54AS646 SN74AS646
Pulse duration
I Clock high 6 5
ns
tw
I Clock low 7 6
tsu Setup time, A before CA8t or B before CBAi 7 6 ns
th Hold time, A after CABt or B after CBAt 0 0 ns
»
r- PARAMETER TEST CONDITIONS
SN54AS646
SN54AS648
SN74AS646
SN74AS648 UNIT
C/) MIN TYPt MAX MIN TYPt MAX
VCC = 4.5 =
»
2
VIK
VCC = 4.5
V,
V to 5.5 V,
II -18 mA
10H = -2 mA VCC-2
-1.2
VCc-2
-1.2 V
VCC - 4.5 V, 10H - -3 mA 2.4 3.2 2.4 3.2

C VOH
VCC - 4.5 V, 10H - -12 mA 2.4
V
»
C/)
VCC = 4.5 V,
VCC - 4.5 V,
10H =
10L - 48 mA
-15 mA
0.35 0.55
2.4
VOL V
n Control inputs
VCC - 4.5 V,
VCC - 5.5 V,
10L - 64 mA
VI - 7 V 0.1
0.35 0.55
0.1
~ II mA
A or B ports VCC = 5.5 V, VI = 5.5 V 0.1 0.1
n Control inputs 20 20
c IIH
A or B portst
VCC = 5.5 V, VI = 2.7V
50 50
/J A
=i
(J) IlL
Control inputs
VCC = 5.5 V, VI = 0.4 V
-0.5 -0.5
mA
A or B portst -0.5 -0.5
10§ VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Outputs high 120 195 120 195
'AS646 Outputs low 130 211 130 211
ICC VCC = 5.5 V mA
Outputs high 110 185 110 185
'AS648 Outputs low 120 195 120 195
tAli typical values are at Vee = 5 V, TA = 25°e
*For 1/0 ports, the parameters IIH and IlL inclu(le the off-state output current.
1283
2-462 TEXAS
INSTRUMENlS
OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3·STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS646 SN74AS646
MIN MAX MIN MAX
f max 75 90 MHz
tpLH 2 9.5 2 8.5
C8A or CAB Aor B ns
tpHL 2 10 2 9
tpLH 2 11 2 9
A or B BorA ns
tpHL 1 8 1 7
tPLH SBA or SABt 2 12 2 11
Aor B ns
tPHL (with A or B high) 2 10 2 9
tpZH 2 10 2 9
G A orB ns
tpZL 3 15 3 14
tpHZ 2 11 2 9
G A or B ns
tPLZ 2 11 2 9
tpZH 3 19 3 16
DIR A or B ns
tpZL 3 21 3 18
tpHZ 2 12 2 10
DIR A or B ns
tpLZ 2 12 2 10

Vee = 4.5 V to 5.5 V.
CL = 50 pF.
(J)
FROM TO
Rl = 500 Q. t:::
PARAMETER R2 = 500 Q. UNIT ::J
(INPUT) (OUTPUT) (.)
TA = MIN to MAX
SN54AS648 SN74AS648 a:
MIN MAX MIN MAX (.)
f max 75 90 MHz (J)
tpLH
tpHL
CBA or CAB A or B
2
2
9.5
10
2
2
8.5
9
ns «
tpLH 2 9 2 8 c
A or B BorA ns z
tpHL
tPLH SBA or SABt
A or B
1
2
8
12
1
2
7
11
ns
«
tpHL (with A or B high) 2 10 2 9 (J)
...I
tpZH
tpZL
G Aor B
2
3
10
18
2
3
9
15
ns
«
tpHZ 2 11 2 9
G Aor B ns
tpLZ 2 11 2 9
tpZH 3 19 3 16
DIR A orB ns
tpZL 3 21 3 18
tPHZ 2 12 2 10
DIR A orB ns
tpLZ 2 12 2 10
tThese parameters are measured with the internal output state of the storage register opposite to that of the bus input.
1283
TEXAS 2-463
INSTRUMENTS
2-464
• Bus Transceivers/Registers SN54ALS·. SN54AS' ..• JT PACKAGE

SN74ALS·. SN74AS' •.• NT PACKAGE
• Independent Registers and Enables for A and ITOPVIEWI
B Buses
CAB VCC
• Multiplexed Real-Time and Stored Data SAB CBA
• Choice of True and Inverting Data Paths GAB SBA
A1 GBA
• Choice of 3-State or Open-Collector Outputs A2 B1
to A Bus
A3 B2
• Included Among the Package Options Are A4 B3
Compact 24-Pin 300-mil-Wide DIPs and A5 B4
Both 28-Pin Plastic and Ceramic Chip A6 B5
Carriers A7 B6
AS B7
• Dependable Texas Instruments Quality and GND B8
Reliability
DEVICE A OUTPUT B OUTPUT LOGIC SN54ALS·. SN54AS' ••• Fe PACKAGE

'ALS651, 'AS651 3-State 3-State Inverting SN74ALS·. SN74AS' ••• FN PACKAGE
'ALS652, 'AS652 3-State 3-State True ITOPVIEWI
'ALS653 Open-Collector 3-State Inverting
'ALS654 Open-Collector 3-State True
~~~U~~~
(f) U Z > U(f)
(!)
description 432 1
These devices consist of bus transceiver circuits, A1 GBA
D-type flip-flops. and control circuitry arranged for A2 B1
multiplexed transmission of data directly from the A3 B2
data bus or from the internal storage registers. Enable NC NC
GAB and GBA are provided to control the transceiver A4 B3 en
functions. SAB and SBA control pins are provided to B4 !::
select whether real-time or stored data is transferred. B5 :::>
A low input level selects real-time data. and a high 12 131415161718 ua:
selects stored data. The following examples r--COOucor--co
demonstrate the four fundamental bus-management <X: <X:ZZCOCIlCIl U
(!)
functions that can be performed with the octal bus en
transceivers and registers.
NC . - No internal connection
«
c
2
«
en
....I
«
~ ~ ~ ~
GAa GBA CAB CBA SAB SBA GAB GBA CAB CBA SAB SBA GAB GBA CAB CBA SAB SBA GAB GBA CAB CBA SAB SBA
l X H H X L X , X X , L H orL H or L H X
X X
REAL-TIME TRANSFER REAL-TIME TRANSFER STORAGE FROM TRANSFER

BUS B TO BUS A BUS A TO BUS B A AND/OR B STORED DATA
TO A AND/OR B
TEXAS 2-465
INSTRUMENTS
Data on the A or B data bus, or both, can be stored in the internal D flip-flops by low-to-high transitions at the ap-
propriate clock pins (CAB or CBA) regardless of the select or enable control pins. When SAB and SBA are in the real-
time transfer mode, it is also possible to store data without using the internal D-type flip-flops by simultaneously enabl-
ing GAB and GBA. In this configuration each output reinforces its input. Thus, when all other data sources to the two
sets of bus lines are at high impedance, each set of bus lines will remain at its last state.
The -1 versions of the SN74ALS651 through SN74ALS654 are identical to the standard versions except that the
recommended maximum IOL is increased to 48 milliamperes. There are no -1 versions of the SN54ALS651 through
SN54ALS654.
The SN54' family is characterized for operation over the full military temperature range of - 55 DC to 125 DC. The
SN74' family is characterized for operation from 0 DC to 70 DC.
FUNCTION TABLE
INPUTS DATA 1/0* OPERATION OR FUNCTION

'ALS651, 'ALS653 'ALS652, 'ALS654
GAB GBA CAB CBA SAB SBA A1 THRU A8 B1 THRU B8 'AS651 'AS652
L H H or L H or L X X Isolation Isolation
Input Input
L H t t X X Store A and B Data Store A and B Data
X H t H or L X X Input Not specified Store A, Hold B Store A, Hold B
H H t t X X Input Output Stora A in both registers Store A in both registers
L X H or L t X X Not specified Input Hold A, Store B Hold A, Store B
L L t t X X Output Input Store B in both registers Store B in both registers
L L X X X L Real-Time B Data to A Bus Real-Time B Data to A Bus
Output Input
L L X H or L X H Stored B Data to A Bus Stored B Data to A Bus
~
H H X X L X Real-Time A Data to B Bus Real-Time A Data to B Bus
Input Output
H H H or L X H X Stored A Data to B Bus Stored A Data to B Bus
Stored A Data to B Bus and Stored A Data to B Bus and
L H or L H or L H Output Output
J> H H
Stored B Data to A Bus Stored B Data to A Bus
r- 'The data output functions may be enabled or disabled by various signals at the GAB and GBA inputs. Data input functions are always enabled. i.e .• data at the
OO bus pins will be stored on every low-to-high transition on the clock inputs.
J> logic diagrams (positive logic)

:2
C 'ALS651, 'AS651, 'ALS653 'ALS652, 'AS652, 'ALS654
J>
·00
(")
::a
(")
c
~
00
.
TO 7 OTHER CHANNELS
..
TO 7 OTHER CHANNELS
1283
2-466 TEXAS
INSTRUMENTS
TYPES SN54ALS651 THRU SN54ALS654. SN54AS651. SN54AS652
SN74ALS651 THRU SN74ALS654. SN74AS651. SN74AS652
logic symbols
'ALS651, 'AS651 'ALS652, 'AS652
GBA (211 GBA (211

ENl (BAI ENl (BAI
GAB (31 EN2 (ABI GAB (31 EN2 (AB]
CBA (231 C4 CBA (231 C4
SBA (221 G5 SBA (221 G6
CAB (1) C6 CAB (11 C6
SAB (21 SAB (21
(201 (20)
(41 (4)
Bl Bl
Al Al
(5) (191 (5) (19)

A2 B2 A2 B2
(SI 1181 (S) (1B)
A3 B3 A3 B3
(71 (17) (7) (17)

A4 B4 A4 B4
(SI I1SI (81 (16)
AS BS AS B5
(9) I1SI (9) (15)

A6 BS A6 BS
(101 (14) 1101 (14)
A7 B7 A7 B7
(11) (131 (11) (13)
A8 BS A8 B8
GBA (21)
'ALS653
GBA (21)
'ALS654 611
en
ENl (BAI
GAB (31
CBA (231
GAB (31
C8A (231
EN2 (ABI !::
SBA (221 S8A (221
C4
:J
CA8 (1)
G6
U
CA8 (1)
SA8 (21 SA8 (2)
C6
a:
(41
(201
81
(4)
(20)
81
U
Al Al
en
<t
(5) (19) (5)
A2 82 A2 C
(S) (181 (SI (18) Z
A3 83 A3 83
<t
A4
(71 ' (171
B4 A4
171 (171
84 en
~
(8) (lS) (81 (lS)
AS BS AS 85 <t
(91 (lS) (91 (15)
AS 8S AS 86
(10) (14) (10) (14)
A7 87 A7 87
1111 (131 (11) (13)

A8 BS A8 88
1283
TEXAS 2-467
INSTRUMENlS
POST OFFICE BOX 225012 • DALLAS, TEXAS 7S265
Supply voltage, Vcc ............................................... " ............... 7 V
Input voltage: Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS651. SN54ALS652 . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS651,SN74ALS652 . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

VIL Low-level input voltage 0.8 I
0.8 V
12 24
48t
CBA or CAB high
CBA or CAB low
tsu Setup time before CABt or CBAt A or B ns
th Hold time after CABt or CBAt A orB ns
-=-
tThe extended condition applies if Vee is maintained between 4.75 V and 5.25 V.
PARAMETER TEST CONDlTIONS SN54ALS652 SN74ALS652 UNIT
MIN TYP:t MAX MIN TYP:t MAX
VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V
VCC = 4.5 V to 5.5 V, 10H = -0.4 mA VCC-2 VCC-2
VCC = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
VCC = 4.5 V, 10H = -12 mA 2
VCC = 4.5 V, 10H = -15 mA 2
Vce = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
VOL Vec = 4.5 V, 10L = 24 mA 0.35 0.5 V
(I0L = 48 mA for -1 versions)
II mA
IIH
A or B ports§
Vce = 5.5 V" VI = 2.7 V
20 20
~A
IlL
A or B ports§
Vee = 5.5 V, VI = 0.4 V -0.2 -0.2
mA
10' Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA

Outputs high 52 52
ICC Vee = 5.5 V mA
Outputs high 60 60
*AII typical values are at Vee = 5 V, TA = 25°e
§For I/O ports, the parameters IIH and IlL include the off·state output current.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
2 -46 8
development. Texa.lnstruments ..serves the right to TEXAS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
f max MHz
tPLH 11 11
CBA or CAB Aor B ns
tpHL 13 13
tpLH 10 10
A or B BorA ns
tpHL 12 12
tpLH SBA or SAB* 16 16
A or B ns
tPLH SBA or SAB* 15 15
A or B ns
tPHL (with A or Blow) 15 15
tpZH 17 17
GBA A ns
tpZL 20 20
tPHZ 10 10
GBA A ns
tPLZ 12 12
tpZH 19 19
GAB B ns
tpZL 22 22
tpHZ 12 12
GAB B ns
tPLZ 14 14

Vcc = 4.5 V to 5.5 V. en
CL = 50 pF. t:
FROM TO
R1 = 500 Q. ::>
(.)
(INPUT) (OUTPUT)
TA = MIN to MAX a:
SN54ALS652 SN74ALS652 (.)
en
f max
tpLH 11 11
MHz
«
tpHL
CBA or CAB A or B
13 13
ns c
z
tpLH
tpHL
A or B B or A
8
8
8
8
ns «
tpLH SBA or SAB*
A or B
16 16
ns
en
tpHL (with A or B high) -I
tpLH SBA or SAB*
A or B
16
15
16
15
ns
«
tpZH 17 17
GBA A ns
tpZL 20 20
tpHZ 10 10
GBA A ns
tpLZ 12 12
tpZH 19 19
GAB B ns
tpZL 22 22
tPHZ 12 12
GAB B ns
tPLZ 14 14
;These parameters are measured with the internal output state of the storage register opposite to that of the bus input.

This pege contains information on a product undar
clavelopment. Texas Instruments re..rv.. the right to TEXAS 2-469
changa or discontinue this product without notice. INSTRUMENlS
Supply voltage, Vee ............ ". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage: All inputs and A I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
B I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS653, SN54ALS654 . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS653,SN74ALS654 . . . . . . . . . . . . . . . . . . . . . . . . 00et070 0e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 150 °e
VOH High-level output voltage A ports 5.6 6.5 V
IOH High-level output current B ports -12 -15 mA
12 24
48t
CBA or CAB high
CBA or CAB low
tsu Setup time before CABi or CBAi A orB ns
th Hold time after CABi or CBAi A or B ns
-=-
tThe extended condition applies if VCC is maintained between 4.75 V and 5.25 V.
~electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
»
r-
PARAMETER TEST CONDITIONS SN54ALS654
MIN TYPt MAX
SN74ALS654
MIN TYPt MAX
UNIT
en VIK VCC = 4.5 V, II = -18 mA -1.5 -1.5 V

»
2
VCC = 4.5 V to 5.5 V,
VCC = 4.5 V,
10H = -0.4 mA
10H = -3 mA
VCC-2
2.4 3.2
VCC-2
2.4 3.2
VOH B ports V
C Vec = 4.5 V, IOH = -12 mA 2
»
en 10H A ports
Vee
Vee
= 4.5 V,
= 4.5 V,
IOH = -15 mA
VOH = 5.5 V 0.1
2
0.1 mA
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
Q VOL Vec = 4.75 V, 10L = 24 mA 0.35 0.5 V
:Xl (lOL = 48 mA for -1 versions)
(") Control inputs Vee = 5.6 V, VI = 7 V 0.1 0.1
c II
mA
=t Control inputs 20 20
en IIH
A or B ports§
Vee = 5.5 V, VI = 2.7V
20 20
IJA

IlL Vce = 5.5 V, VI = 0.4 V mA
A or B ports§ -0.2 -0.2
10' B ports Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Outputs high 52 52
lee Vee = 5.5 V mA
Outputs high 60 60
tAli typical values are at vcc ~ 5 V. TA = 25 D C
§For I/O ports, the parameters IIH and IlL include the off-state output curre.nt.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
2 -4 7 0
Thf. page contain. information on a product under
development. Texa. lnotrument. relSrve. the right to TEXAS
change or discontinue thf. product without notice. INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 680 Q. (A outputs)
FROM TO
PARAMETER R1 = R2 = 500 Q. (8 outputs) UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
f max MHz
tPLH 24 24
CBA A ns
tpHL 15 15
tpLH 11 11
CAB B ns
tpHL 13 13
tPLH 10 10
A B ns
tpHL 12 12
tPLH 24 24
B A ns
tPHL 10 10
tPLH SBA* 26 26
A ns
tpHL (with B high) 15 15
tPLH SBM 26 26
A ns
tPHL (with Blow) 15 15
tpLH SAB* 16 16
B ns
tpHL (with A high) 16 16
tpLH SAB* 15 15
B ns
tpHL (with A low) 15 15
tPLH 24 24
GBA A ns
tPHL 17 17
en
tpZH
tpZL
GAB B
19
22
19
22
ns t::
tpHZ 12 12
:J
GAB B ns U
tpLZ 14 14 a:
iThese parameters are measured with the internal output state of the storage register opposite to that of the bus input. U
NOTE 1: For load circuit and voltage waveforms. see page 1·'2.
Additional information on these products can be obtained from the factory as it becomes available. en
«
c
z
«
en
...J
«

Thli peg. contalnl information on a product und.,
dev"""",*". Toxallnltnlmonta , ...rv.. tho right to , TEXAS 2-471
cheng. or dllcontlnu. thli product wltho'!l notleo. INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 680 Q. (A outputs)
FROM TO
PARAMETER R1 = R2 = 500 Q. (B outputs) UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
f max MHz
tpLH 24 24
CBA A ns
tpHL 15 15
tpLH 11 11
CAB B ns
tpHL 13 13
tpLH 8 8
A B ns
tpHL 8 8
tpLH 24 24
B A ns
tpHL 10 10
tpLH SBA* 26 26
A ns
tpHL (with B high) 15 15
tPLH SBAi 26 26
A ns
tPHL (with Blow) 15 15
tpLH SAB* 16 16
B ns
tpHL (with A high) 16 16
tpLH SAB* 15 15
B ns
EI tPHL
tpLH
tpHL
(with A low)
GBA A
12
24
17
12
24
17
ns
l> tpZH 19 19
r- GAB B ns
en tpZL
tPHZ
22
12
22
12
GAB B ns
l> tpLZ 14 14
2 tAli typical values are at Vee = 5 V. TA = 25°e.
C tThese parameters are measured with the Internal output state of the storage register opposite to that of the bus input.
l> Additional Information on these products can be obtained from the factory as It becomes available.
en
(').
:xl
(')
c
=i
en
2 -4 7 2
development. TexallnstNmentl ..serv.. the right to TEXAS
POST OFFICE BOX 225012 e DALLAS. TeXAS 75265
absolute maximum ratings over operating free-air temperature'range (unless otherwise noted)
Supply voltage, VCC ..... ". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage: Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
110 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . _..... 5.5 V
Operating free-air temperature range: SN54AS651, SN54AS652 . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125°C
SN74AS651,SN74AS652 . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC
Storage temperature range . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . . . . . . . . . . . _ .... - 65 DC to 150°C

SN54AS651 SN74AS651
fclock 0 75 0 90 MHz
C8A or CAB high 6 5
CSA or CAB low 7 6
tsu Setup time before CABt or CBAt A or B 7 6 ns
th Hold time after CABt or CBAt A or B O· 0 ns
PARAMETER TEST CONDITIONS SN54AS652
MIN TYPt MAX
SN74AS652
MIN TYPt MAX
UNIT
!::
::>
VIK VCC = 4.5 V,
= 4.5 V to
II = -18 mA -1.2 -1.2 V
u
VCC 5.5 V, IOH = -2 mA VCC-2 VCC-2 a:
Vee = 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
VOH
Vce = 4.5 V, IOH = -12 mA 2.4
V u
VCC = 4.5 V, IOH = -15 mA 2.4 en
VOL
VCC = 4.5 V, IOL = 48 mA 0.35 0.55
V
<t
VCC = 4.5 V, IOL = 64 mA 0.35 0.55
C
II
Control inputs VCC = 5.5 V,
= 5.5 V,
VI = 7 V
VI = 5.5 V
0.1 0.1
mA z
A or B ports
Control inputs
Vee 0.1
20
0.1
20
<t
IIH
A or B ports;
VCC = 5.5 V, VI = 2.7V 50 50
IlA en
....J
IlL
Control inputs
A or B ports;
VCC = 5.5 V, VI= 0.4 V
-0.5
-0.5
-0.5
-0.5
mA <t
IO§ VCC = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Outputs high 110 185 110 185
'AS651 Outputs low 120 195 120 195
ICC VCC = 5.5 V mA
Outputs high 120 195 120 195
'AS652 Outputs low 130 211 130 211
t All typical values are at Vee = 5 V, TA = 25 De
i For 1/0 ports, the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-473
INSTRUMENlS

Vcc = 4.5 V to 6.6 V.
CL = 50 pF.
Rl = 600 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS651 SN74AS651
MIN MAX MIN MAX
f max 75 90 MHz
tpLH 2 9.5 2 8.5
tPHL 2 10 2 9
tpLH 2 9 2 8
A or B BorA ns
tpHL 1 8 1 7
tpLH 2 12 2 11
SBA or SABt A or B ns
tpHL 2 10 2 9
tpZH 2 11 2 10
GBA A ns
tpZL 3 18 3 16
tpHZ 2 10 2 9
GBA A ns
tpLZ 2 10 2 9
tpZH 3 12 3 11
GAB B ns
tpZL 3 20 3 16
tPHZ 2 11 2 10
GAB B ns
tpLZ 2 12 2 11
_ ' AS652 switching characteristics (see Note 1)

Vcc = 4.6 V to 5.5 V.
»
r-
CL = 50 pF.
Rl = 600 Q.
fJ) FROM TO
PARAMETER· R2 = 500 Q. UNIT
»
:2
(INPUT) (OUTPUT)
SN54AS652
TA = MIN to MAX
SN74AS652
C MIN MAX MIN MAX
f max
»
fJ)
tpLH
CBA or CAB A or B
75
2 9.5
90
2 8.5
MHz
ns
tpHL 2 10 2 9
Q tpLH
tpHL
A or B BorA
2
1
11
8
2 9
7
ns
:Il 1
("). tpLH 2 12 2 11
c tpHL
SBA or SABt A orB
2 10 2 9
ns
=i
fJ)
tpZH
tpZL
GBA A
2
3
11
18
2
3
10
16
ns
tpHZ 2 10 2 9
GBA A ns
tpHL 2 10 2 9
tPZH 3 12 3 11
GAB B ns
tpZL 3 20 3 16
tPHZ 2 11 2 10
GAB B ns
tpLZ 2 12 2 11
tThese parameters are measured with the internal output state of the storage register opposite to that of the bus input.
1283
2-474 TEXAS
INSTRUMENTS
ADDRESS COMPARATORS
02661. JUNE 1982-REVISEO DECEM8ER 1983
SN54ALS677 • • • JT PACKAGE
SN74ALS677 • . • .NT PACKAGE
(TOP VIEW)
• 'ALS677 is a 16-bit to 4-Bit Comparator with Enable
• 'ALS678 is a 16-Bit to 4-Bit Comparator with Latch
A4 4 21 P3
• Package Options Include Both Plastic and Ceramic A5 20 P2
Chip Carriers in Addition to Plastic and Ceramic DIPs A6 19 Pl
A7 18 po
• Dependable Texas Instruments Quality and Reliability AS 17 A16
A9 16 A15
Al0 10 15 A14
description All 11 14 A13
GNO 12 13 A12
The 'ALS677 and 'ALS678 address comparators simplify
addressing of memory boards and/or other peripheral devices. SN54ALS677 FH PACKAGE
The four P inputs are normally hard wired with a preprogrammed SN74ALS677 FN PACKAGE
address. An internal decoder determines what input information
applied to the 16 A inputs must be low or high to cause a low
state at the output (Y). For example, a positive-logic bit combina-
4 3 2 1 282726
tion of 0111 (decimal 7) at the P input determines that inputs A 1
A4 25 P3
through A 7 must be low and that inputs A8 through A 1 6 must A5 24 P2
be high to cause the output to go low. Equality of the address A6 23 Pl
applied at the A inputs to the preprogrammed address is NC 22 NC
A7 9 21 PO
indicated by the output being low. A8 10 20 A16
A9 11 19 A15
The' ALS677 features an enable input (G). When G is low, the 12131415161718
device is enabled. When G is high, the device is disabled and the
output is high regardless of the A and P inputs. The' ALS678
features a transparent latch and a latch enable input (e). When e
--22---
O_OUNM.r
«I!l «<
is high, the device is in the transparent mode. When e is low, the SN54ALS678 • • . JT PACKAGE en
previous logic state of Y is latched. SN74ALS678 • . • NT PACKAGE
(TOP VIEW)
!::
The SN54ALS677 and SN54ALS678 are characterized for :::J
operation over the full military temperature range of - 55 °e to
Al VCC U
125 °e. "T:he SN54ALS677 and SN74ALS678 are characterized
A2
A3
C a:
for operation from ooe to 70 0 e. A4 P3 U
A5 P2
A6 Pl en
A7
A8
PO
A16
«
A9 A15 c
Al0 10 15 A14
z
All
GNO
11
12
14
13
A13
A12 «
SN54ALS678 . FH PACKAGE en
..oJ
SN74ALS678 . FN PACKAGE
(TOP VIEW) «
U
M N - U U
«<Z>U>-
4 3 2 1 282726
A4
A5
A6
NC
A7
AS 10
A9 11
12 1314 15161718
--2Z---
O_OUNM'¢
«I!l «<

1283
ThIs document contains Inlonnatlon On e product under
development. Texas Instrumentl reaerve. the right to TEXAS 2-475
change or dilcontlnu8 this product without notice.
INSTRUMENTS
ADDRESS COMPARATORS
FUNCTION TABLE
'ALS677 'ALS678 INPUTS COMMON TO 'ALS677 AND 'ALS678 OUTPUT

G C P3 P2 P1 PO A1 A2 A3 A4 A5 A6 A7 A8 A9 A10A11 A12A13A14A15A16 V
L H L L L L H H H H H H H H H H H H H H H H L
L H L L L H L H H H H H H H H H H H H H H H L
L H L L H L L L H H H H H H H H H H H H H H L
L H L L H H L L L H H H H H H H H H H H H H L
L H L H L L L L L L H H H H H H H H H H H H L
L H L H L H L L L L L H H H H H H H H H H H L
L H L H H L L L L L L L H H H H H H H H H H L
L H L H H H L L L L L L L H H H H H H H H H L
L H H L L L L L L L L L L L H H H H H H H H L
L H H L L H L L L L L L L L L H H H H H H H L
L H H L H L L L L L L L L L L L H H H H H H L
L H H L H H L L L L L L L L L L L H H H H H L
L H H H L L L L L L L L L L L L L L H H H H L
L H H H L H L L L L L L L L L L L L L H H H L
L H H H H L L L L L L L L L L L L L L L H H L
L H H H H H L L L L L L L L L L L L L L L H L
L H All other combinations H
H 'ALS677: Any combination H
L 'ALS678: Any combination Latched
- l>
logic symbols
'} .':
'ALS677
(ADDRESS COMPI
'ALS678
(ADDRESS COMPI
r"
G (23) EN
(23)
C20
r- (18)
-I &1> (18)
-I
en PO
PI
I1S) P;' 2 -I
PO
PI
I1S)
o 1
P;' 2 -I
l> P2
(20)
P 2
P;' 3 P2
(20)
P
P> 3
2
-I
2 P3
(211 3 3 P3
(211 3 3
C Al
(1)
II
p;, 4
AI
(1)
II
p;, 4 -I
l> A2
(2)
l2
p;, 5 (2) P;;' S -I
en A3
(3)
l3 P;;' 6
A2
A3
(3)
l2
l3 P;' 6 -I
(4) 6
(") A4 l4 A4
(4)
P;' 7
::0 AS
p;, 6
AS
(") A6 (22) y
A6
c: A7 P;' 9 -I A7
=t
en
A8
AS
9
P;.10 -I
A8
10
P;'11 -I
11
All (11) l11 P;;.12 -I A11
A12 (13) 12
l12
A13 (14) l13
A14 (16) A14 (16)
l14 l14
AIS (18) lIS AIS (16) lIS P_ 1
A16 (17) A16 (17) 1
l16 l16
16 16
1283
2-476 TEXAS
INSIRUMENTS
POST OF.FICE BOX 225012 • DALLAS. TEXAS 75265
TYPES SN54ALS677, SN54ALS678, SN74ALS677, SN74ALS678,
ADDRESS COMPARATORS
'ALS677 'ALS678
A1 111 A1 111
A2 121 A2 121
A3 131 A3 131
A4 141 A4 141
A5 151 A5 151
A6 161 A6 161
A7 171 A7 171
AB IBI AB IBI
1221 V . .
A9 191 191
A9
en
A 1 0 ..:..;11~01'----+++-r-;=-_---'~ A10 1101
t:
:::>
A11 1111
u
A11 1111
a:
A12 1131
u
en
«
A13 (141 A13 (141
c
z
A14 ...;..11;.,;:;5.:....1_++++-_ _ _....... _- A14 1151
«
en
..oJ
«
A15 (161 A15 (161
A16 1171
PO
P1"":":'::"-C»-'
P2 -'=-'--{::O-........
P3 1211 P3 -=-"--i.::O-~
G 1231 C 1231
1283
TEXAS 2-477
INSTRUMENTS
ADDRESS COMPARATORS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS677, SN54ALS678 . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 60 °e

-
»
r- VIK Vee = 4.5 V, II = -18 mA
MIN Typt MAX
-1.5
MIN Typt MAX
-1.5 V
CJ) Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2
»
2
VOH Vee
Vee
=
=
4.5 V,
4.5 V,
IOH
IOH
=
=
-1 mA
-2.6 mA
2.4 3.3
2.4 3.2
V
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4

C VOL
Vee = 4.5 V, IOL - 24 mA 0.35 0.5
V
»
CJ)
II
IIH
Vee
Vee
=
=
5.5 V,
5.5 V,
VI
VI
=7V
= 2.7 V
0.1
20
0.1
20
mA
p.A
(") IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
:lJ l'ALS677 21 33 21 33
(") lee Vee = 5.5 V mA
c: l'ALS678 17 17
::::f tAli typical values ar(l at Vee = 5 V, TA = 25°e.

CJ) tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
Additional information on these products can be obtained from the factory as It becomes available.
1283
2-478 TEXAS
INSTRUMENTS
ADDRESS COMPARATORS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
PARAMETER
FROM TO RL = 500 n. UNIT
MIN MAX MIN MAX
tpLH 4 28 4 25
Any P Y ns
tpHL 8 40 8 35
tpLH 5 26 5 22
Any A Y ns
tpHL 5 35 5 30
tpLH 3 15 3 13
IT Y
30 5 25
ns
tpHL 5
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO
PARAMETER
(INPUT) (OUTPUT)
RL = 500 n. UNIT
TA = MIN to MAX
tpLH 18 18
Any P Y ns
tPHL 18 18
tpLH 14 14
tpHL
Any A Y
14 14
ns
en
tpLH y
14 14 I-
C ns
tpHL 14 14 :>
= = U
t All typical values are at Vee 5 V. TA 25°e.
a::
u
en
«
c
2
«
en
-oJ
«
1283
TEXAS 2-479
INSTRUMENTS
ADDRESS COMPARATORS
The' ALS6 77 and' ALS6 7 8 can be wired to recognize anyone of 2 16 - 1 addresses. The number of "lows" in the address
determines the input pattern for the P inputs. Then those system address lines that are low in the address to be recognized
are connected to the lowest numbered A inputs of the address comparator and the system address lines that are high are
connected to the highest numbered A inputs.
For example, assume the comparator is to enable a device when the 16-bit system address is:
A15 A14 A13 A12 All Al0 A9 A8 A7 A6 A5 A4 A3 A2 Al AO

H H L L H H L L H H L L H H H H
Since the address contains 6 lows and 10 highs, the following connections are made:
P3 to 0 V, P2 to Vee, Pl to Vee, and PO to 0 V.

, I
System address lines A 13, A 12, A9, A8, A5, and A4 to comparator inputs A 1 through A6 in any convenient order.
The remaining ten system address lines to comparator inputs A7 through A 16 in any convenient order.
The output provides an active-low enabling signal.
The following circuit is a modulo-N synchronous counter. The' ALS163 is connected to provide a low-level clear signal when
N = FEFF16.
IIfJ FEFF16
15
=
12 8 4 0
HHHH HHHL HHHH HHHH
l>
r-
CJ) 4
'ALS677
'ALS163
l> CTR 16
ADDRESS
-2 COMP
C CLK
lR EN
Cl/+ VCC
l>
CJ)
(") 8
:}P MAX COUNT
0 ... 7
:xJ
(") 8
-= Al
IP = 11
C 9 ... 15
15 A2. .. A16
~
en
MODULO-N SYNCHRONOUS COUNTER
1283
2-480 TEXAS
INsrRUMENlS
ADDRESS COMPARATORS
02661. JUNE 1982-REVISED DECEMBER 1983
• ' ALS679 is a 12-Bit to 4-Bit Comparator With Enable SN54ALS679 ... J PACKAGE
SN74ALS679 ..• N PACKAGE
• ' ALS680 is a 12-Bit to 4-Bit Comparator With Latch (TOP VIEW)
.. Package Options Include Both Plastic and Ceramic Al I U20 VCC
Chip Carriers in Addition to Plastic and Ceramic DIPs A2 2 19 G
A3 3 18 Y
o Dependable Texas Instruments Quality and Reliability A4 17 P3
AS 16 P2
A6 15 Pl
A7 14 PO
A8 13 A12
description A9 12 All
GNO 10 11 Al0
The ' ALS679 and 'ALS680 address comparators simplify
addressing of memory boards and/or other peripheral devices. SN54ALS679 ... FH PACKAGE
The four P inputs are normally hard wired with a preprogrammed SN74ALS679 ••. FN PACKAGE
address. An internal decoder determines what input information (TOP VIEW)
applied to the 1 2 A inputs must be low or high to cause a low U
M N _ U
state at the output (Y). For example, a positive-logic bit <{ <{ <( > Ie:)
combination of 0111 (decimal 7.) at the P input determines that 3 2 1 20 19
inputs A 1 through A 7 must be low and that inputs A8 through
A 12 must be high to cause the output to go low. Equality of the
address applied at the A inputs to the preprogrammed address is
indicated by the output being low.
9 1011 1213
The' ALS679 features an enable input (G)' When G is low, the
cnOO~N
device is enabled. When G is high. the device is disabled and the <{Z~~~
(!)<{<{<{
output is high regardless of the A and P inputs. The ' ALS680
features a transparent latch and a latch enable input (C). When C
is high, the device is in the transparent mode. When C is low, the
SN54ALS680 ... J PACKAGE en
previous logical state of Y is latched.
SN74ALS680 ••• N PACKAGE !::
(TOP VIEW) :::>
The SN54ALS679 and SN54ALS680 are characterized for C,)
operation over the full military temperature of - 55 °C to
Al 1 U20 VCC a:
125 °C. The SN74ALS679 and SN74ALS680 are characterized
A2
A3
A4
2
t7
::F ~ P3
u
AS 16 P2 en
A6 15 Pl <C
A7
A8
14
13
PO
A12 o
A9 ,9 12 All z
GNO 10 11 Al0 <C
SN54ALS680 •.• FH PACKAGE en
SN74ALS680 ..• FN PACKAGE
...J
(TOP VIEW) <C
U
M N - U
«<{<{>t)
3 2 1 2019
A4 4 y
AS P3
A6 P2
A7 Pl
A8 PO
9 1011 1213

1283
discontinue this product without notice. POST OFFiCe BOX 225012 • ,DALLAS, TeXAS 75265
ADDRESS COMPARATORS
FUNCTION TABLE
'ALS679 OUTPUT
G C V
L H L
L H L H H H H H H H L
H H L H H H H H H H H H H L
H L H H L L H H H H H H H H H L
L H H L L L L H H H H H H H H
L H H L H L L L H H H H H H H
L H H H L L L H H H H H H L
L H H H H L -L H H H H H L
H H L L L L L H H· H H
L H H L H L L L L H H H L
H H H L L L L H H L
H H L H H L L L L H
-
logic symbols
'ALS679 'ALS680
[ADDRESS COMPI [ADDRESS COMPI
G (19) [P assumed ~ 12,13,141 [P assumed ~ 12,13,141
'} ": '} ":

EN C20
PO (14)
=1 &[> =1 &
l> Pl (15)
r-
en P2 (16)
P P;;' 2
2
P p;;, 2
2
l> P3 (17)
3
p;;, 3 P;;' 3
:2 3 3 3
Al (1)
C Zl p;;. 4 Zl p;;. 4
A2 (2) 4
l> Z2
P;;' 5
Z2
P;;' 5
en Z3 Z3
C') P;;' 6 (18) P;;' 6
Z4 y Z4 y
6 6
::D ZS p;;, 7 ZS P;;' 7
C')
7
C Z6
P;;' 8
Z6
p;;, 8
=i Z7 Z7 8
en Z8
P;;' 9
Z8
P;;' 9
9
Z9 P;;.10 Z9 P;;.10
10 Al0 (11) 10
Z10 Z10
P;;'ll P;;'ll
(12)
Zll 11 All Zl1 • 11
P;;'12 =1 P;;.12
Z12 A12 (13) Z12
12 12
*The three shaded rows of the function table show combinations that would normally not be used in address comparator applications. The logic symbols above
are not valid for these combinations in which P = 12, 13, and 14. If symbols valid for all combinations are required, starting with the fourth ~xclusive-OR from
the bottom, change po;. 9 to P = 9 ... 11/13 ... 15, P .. 10 to P = 10/11114/15, and P .. 11 to P = 11/15.
1283
2-482 TEXAS
INSTRUMENTS
ADDRESS COMPARATORS
'ALS679 'ALS680
11) 11)
Al Al
12) . 12)
A2 A2
13) 13)
A3
14) 141
A4 A4
151 151
A5 A5
161 161
A6 A6
A7
A8
171
181
191
A7
A8
A9
171
181
191
.. en
C
:::>
1111 1111 u
Al0 Al0
a:
1121 1121
U
All
All
en
A12
1131
A12
«
PO PO
C
2
Pl
P2
1161
Pl
P2
«
P3
1171
P3
1171 en
..oJ
«
1191 1191
G
1283
TEXAS 2-483
INSfRUMENTS
ADDRESS COMPARATORS
a1bsolute maximum ratings over operating free-air temperature range (unless otherwise noted)

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ' . . . . . . . . . . . . . . 7 V
SN74ALS679,SN74ALS680 . . . . . . . . . . . . . . . . . . . . . . . 00eto700e

" MIN NOM MAX MIN NOM MAX
-
l> VIK Vee = 4.5 V, II = -18 mA -1.5 - 1.5 V

r- Vee - 4.5 V to 5.5 V, 10H - -0.4 mA Vee-2 Vee-2
CA VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
l> Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
2 VOL V
C Vee = 4.5 V, 10L = 24 mA 0.35 .0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
l> IIH Vee = 5.5 V, VI = 2.7 V 20 20 /LA
CA IlL Vee - 5.5 V, VI = 0.4 V -0.1 -0.1 mA
n 10; Vee = 5.5 V, Vo = 2.25 V -30 - 1 12 -30 - 1 12 mA
:JJ L'ALS679 Vee = 5.5 V

17 28 17 28
mA
n ICC
I 'ALS680 13.4 13.4
c tAli typical values are at Vee = 5V.TA = 25°C.
=i tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
VI
1283
2-484 TEXAS
INSTRUMENTS
TYPES SN54ALS679. SN54ALS680. SN74ALS679. SN74ALS680.
ADDRESS COMPARATORS

Vee = 4.5 V to 5.5 V,
eL = 50 pF,
FROM TO RL = 500 n,
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 4 28 4 25
Any P Y ns
tpHL 8 40 8 35
tpLH 5 26 5 22
Any A Y ns
tPHL 5 35 5 30
tpLH 3 15 3 13
G Y ns
tPHL 5 30 5 25

Vee = 4.5 V to 5.5 V,
eL = 50 pF,.
FROM TO RL = 500 n,
PARAMETER UNIT
(INPUT) (OUTPUT) TA = MIN To MAX
tpLH 18 18
Any P Y ns
tpHL 18 18
tpLH 14 14
Any A Y ns
tpHL 14 14
tpLH 14 14
C Y ns
tpHL 14 14 en
tAli typical values are at Vee = 5 V. TA = 25°e. !::
NOTE 1: For load circuit and voltage waveforms. see page 1-12. ::>
ua:
U
en
<t
C
2
<t
en
..;"J
<t
1283
TEXAS 2-485
INSTRUMENTS
ADDRESS COMPARATORS
The' ALS679 and' ALS680 can be wired to recognize anyone of 212 addresses. The number of "lows" in the address
determines the input pattern for the P inputs. Then those system address lines that are low in the address to be recognized
are connected to the lowest numbered A inputs of the address comparator and the system address lines that are high are
connected to the highest numbered A inputs.
For example, assume the comparator is to enable a device when the 12-bit system address is:
All Al0 A9 A8 A7 A6 A5 A4 A3 A2 Al AO
H H L L H H L L H H H H
Since the address contains 4 lows and 8 highs, the following connections are made:
P3 to 0 V, P2 to Vee, Pl to 0 V, and PO to 0 V.
System address lines A9, A8, A5, and A4 to comparator inputs A 1 through A4 in any convenient order.
The remaining eight system address lines to comparator inputs A5 through A 12 in any convenient order.
The output provides an active-low enabling signal.

The following circuit is a register bank decoder that examines the 14 most significant bits (AO through A 13) of a 20-bit ad-
dress to select banks corresponding to the hex addresses 10000, 10040, 10080, and 100eO.
'ALS679
ADDRESS 0 4 8 12 16
COMP 1000016 = LLLH LLLL LLLL LLLL LLLL
MEMEN G,...", 1004016 = LLLH LLLL LLLL LHLL LLLL
S~ EN
1008016 = LLLH LLLL LLLL HLLL LLLL
PO 100e016 = LLLH LLLL LLLL HHLL LLLL
SYSTEM
VCC
:1
ADDRESS P1
LINES
AD (MSB)
P2 f:::..-
TO A19
-¥ P3
X/Y
'.
AO ... A2 11 A1...A11 [P= 11 )
S·
A4 ... A11
A3
,
~
A12
~ 0 ......
1
1000016
...... 1004016 -
-- 64 x N-BIT
S~
1008016 .. REGISTERS
A13
A12
S·
A
B
2 ......
100C016 _
- }
si 3t-.....
A14 ... A19
SS , SO ... S5
REGISTER BANK DECODER
1283
2-486 TEXAS
INSTRUMENTS
02661. JUNE 1982·REVISED DECEMBER 1983
• Compares Two Eight·Bit Words SN54ALS688, SN54ALS689 ••• J PACKAGE

SN74ALS688, SN74ALS689 .•. N PACKAGE
• Choice of Totem·Pole or Open-Collector Outputs (TOPVIEWI
• Package Options Include Both Plastic and Ceramic G Vee
Chip Carriers in Addition to Plastic and Ceramic DIPs PO p=o
• Dependable Texas Instruments Quality and Reliablility 00 07
P1 P7
OUTPUT FUNCTION 01 06
TYPE AND P6
CONFIGURATION 02 05
'ALS688t ~ totem·pole P3 P5
'ALS689 ~ open-collector 03 04
t'ALS688 is identical to 'ALS521 GND P4
description
These identity comparators perform comparisons of two eight-bit
binary or BCD words. The' ALS688 and' ALS689 provide P = 0
outputs. The' ALS688 has totem-pole outputs, while' ALS689 SN54ALS688, SN54ALS689 .•• FH PACKAGE
has open-collector outputs. SN74ALS688, SN74ALS689 •.. FN PACKAGE
(TOPVIEWI
operation over the full military temperature range of - 55 °e to
125 °e. The SN74ALS688 and SN74ALS689 are characterized
00
d a..lc!)
ul
u
>
d
II
a..
for operation from 0 °e to 70 °e.
FUNCTION TABLE P1 4 07
INPUTS
01 5 P7
OUTPUT P2 6 06
DATA ENABLE
P,Q G
P=Q 02 7 P6 en
P=Q L L
P3 8 05 !::
P>O L H :>
P<O L H (')Oq-q-U') u
X H H
dza..da..
C!)
a:
U
logic symbols en
'ALS688 'A LS689 cd:
COMP c
z
]p~ cd:
en
...J
cd:
(191 P=Q
1P=Q
Q Q

1283
TEXAS 2-487
INSfRUMENlS
P7
07
P6
06
P5
Q5
P4
04
n---:..;11;.:,.9;.,.1_ p,;a
P3
03
P2
02
P1
01
PO
00
Input voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage: 'ALS689 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS688, SN54AS689 . . . . . . . . . . . . ; ........ - 55°C to 125°C
SN74ALS688,SN74AS689 . . . . . . . . . . . . . . . . . . . . . . . . . OOCt070oC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C
1283
2-488 TEXAS
INSTRUMENTS
8·BIT IDENTITY COMPARATORS WITH TOTEM·POLE OUTPUTS

UNIT
Vee Supply voltage 4.5 5 5.5 4.5 5 5:5 V
VIK Vee = 4.5 V, 11= -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA Vcc- 2 vee- 2
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
, 3.2
Vee = 4.5 V, 10H = -2.6 rnA 2.4
Vee = 4.5 V, 10L = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10L = 24 rnA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL Vee - 5.5 V, VI - 0.4 V -0.1 -0.1 rnA
10; Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
Ice Vee = 5.5 V See Note 1 12 19 12 19 rnA
en
tAli typical values are at Vee = 5 V, TA = 25°e. t:::
*The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS. :::>
NOTE 1: ICC is measured with G grounded, P and Q at 4.5 V. u
a:
U
Vcc = 4.5 V to 5.5 V.
<t
CL = 50 pF. C
FROM TO RL = 500 Q, :2
PARAMETER
UNIT
<t
..J
MIN MAX MIN MAX
tPLH
P P=Q
3 16 3 12
ns
<t
tpHL 5 25 5 20
tpLH 3 16 3 12
Q P=Q ns
tpHL 5 25 5 20
tpLH 3 15 3 12
G P=Q ns
tpHL 5 25 5 22
1283
TEXAS 2-489
INSTRUMENTS
8·BIT IDENTITY COMPARATORS WITH OPEN·COLLECTOR OUTPUTS

UNIT
IOH High-level output current 5.5 5.5 V
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
IOH Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
Vee = 4.5 V. IOL = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 24 mA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 j.lA
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
-=-
_
ICC Vee = 5.5 V.

See Note 1
NOTE 1: lee is measured with G grounded, P and Q at 4.5 V.

12 19 12 19 mA

Vee = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 680 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tPLH 10 30 10 25
P P=Q ns
tpHL 5 25 5 23
tpLH 10 30 10 25
Q P=Q ns
tpHL 5 25 5 23
tpLH 8 30 8 25
IT ~ ns
tpHL 8 30 8 25
NOTE 2: For load circuit and voltage I!Vaveforms, see page 1-12.
1283
2-490 TEXAS
INSTRUMENTS
OCTAL BUFFERS AND LINE DRIVERS WITH OPEN·COLLECTOR OUTPUTS
• Open·Coliector Outputs Drive Bus Lines or SN54AS' •.• JPACKAGE

Buffer Memory Address Registers SN74AS' •.• N PACKAGE
(TOPVIEWI
• Eliminates the Need for 3-State Overlap
Protection . 1<3 Vcc
1A1 2G/2G*
• P-N-P Inputs Reduce DC Loading 2Y4 1Yl
• Dependable Texas Instruments Quality and 1A2 2A4
Reliability 2Y3 1Y2
1A3 2A3
• Open-Collector Versions of 'AS240, 'AS241 - 2Y2 1Y3
lA4 2A2
description
2Y1 lY4
These octal bus transceivers are designed specifically GND 2A1
to improve both the performance and density of
three-state memory address drivers, clock drivers, SN54AS' ••. FH PACKAGE
and bus-oriented receivers and transmitters by SN74AS' ••. FN PACKAGE
eliminating the need for three-state overlap protec- (TOPVIEWI
tio·n. The designer has a choice of selected combina-
*
(!)
tions of inverting and noninverting outputs, sym-
q-.... U ~
metrical G (active-low output control) inputs, and >- c::( I(!) UI(!)
N ........ >N
complementary G and G inputs. These devices
feature high fan-out and improved fan-in.
lYl
2A4
lA3 6 lY2
1 25 °C. The SN74' family is characterized for opera-
2Y2 2A3
tion from ooC to 70 0 C.
1A4 1Y3
en
.... O..-q-N !::
>-zc::(>-c::( :::>
N(!)N .... N
u
·2G for 'AS756 or 2G for 'AS757 a:
u
en
<C
C
2
<C
en
-oJ
<C

ThIs document contains Information on a product under
development. T exes Instruments reserve8 the right to TEXAS 2-491
logic symbols
'AS756 'AS757
118)
lYl lYl
116)
1Y2 1Y2
114)
lY3 lY3
112)
lY4 1Y4
19)
2Al 2Yl 2Al 2Yl
2A2 2Y2 2A2
m 2Y2
15)
2A3 2Y3 2A3 2Y3
13)
2A4 2Y4 2A4 2Y4

'AS756 'AS757
1181 I1BI 1Yl

lYl
1161 1161 1Y2

1Y2
IIIfJ 1141 lY3 1141 1Y3
:t> 1121
1Y4 1121 lY4
r-
en 2<: 1191
:t> >---if---'19~1 2Y 1
2
C >O----1t---'1"",-71 2Y 2 >---if---'17'"-.1 2Y2
:t>
en J>O---1r--:1.::....
51
2Y3 >----1t---'1~51 2Y3
n :>0-_--::13::;,..1 >-_----'1~31 2Y4

:a 2Y4
n
c Pin numbers shown are for J and N packages.
=i
en
1283
2-492 TEXAS
INSTRUMENTS
OCTAL BUFFERS AND LINE DRIVERS WITH OPEN-COLLECTOR OUTPUTS
Supply voltage, Vcc ............................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS756, SN54AS757 . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125 °c
SN74AS756,SN74AS757 . . . . . . . . . . . . . . . . . . . . . . . . . . OOCt070 o C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 0 C

SN54AS756 SN74AS756
SN54AS756 SN74AS756
VIK Vee - 4.5 V, II = -18 rnA -1.2 -1.2 V
IOH Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
VOL
Vee = 4.5 V, IOL = 48 rnA 0.55
V en
Vee = 4.5 V, IOL = 64 rnA 0.55
!::
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
::::>
IIH
IlL
Vee - 5.5 V,
Vee = 5.5 V,
VI = 2.7V
VI = 0.4 V -0.3
20
-0.3
20 j.lA
rnA
ua:
Outputs high 16 16
'AS756
Outputs low 51 51
U
lee Vee = 5.5 V rnA
en
'AS757
Outputs high
Outputs low
27
61
27
61 «
tAli tYPIcal values are at Vee = 5 V. TA = 25°e
Additional information on these products can be abtained from the factory as it becomes available.
c
2
«
en
...J
«
283
TEXAS 2-493
INSTRUMENTS
, AS7 56 switching characteristics (see Note 11

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54AS756 SN74AS756
tPLH 20 20
A V ns
·tpHL 6 6
tpLH
y
22 22
G ns
tpHL 8 8
, AS7 5 7 switching characteristics (see Note 11

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54AS757 SN74AS767
tpLH 20 20
A Y ns
tpHL 6 6
tpLH 22 22
1G Y ns
tpHL 8 8
16 tpLH
tPHL
2G
Y
23
9
23
9
ns
:t:- NOTE 1: For load circuit and voltage waveforms. see page 1·12.
ro-
en
:t:-
2
C
:t:-
en
n
::D
n
c:
=i
en
1283
2-494 TEXAS
INSTRUMENTS
QUADRUPLE BUS TRANSCEIVERS WITH OPEN·COLLECTOR OUTPUTS
DECEMBER 19B3
• 2-Way Asynchronous Communication SN54' . . . J PACKAGE

Between Data Buses SN74' . . '. N PACKAGE
(TOP VIEW)
• P-N-P Inputs Reduce Loading
GAB VCC
NC GBA
Reliability
A1 NC
• Open-Collector Versions of ' AS242, , AS243 A2 B1
A3 B2
description A4 B3
GND B4
These four-data-Iine transceivers are designed for
asynchronous two-way communications between
data buses. SN54' FH PACKAGE
SN74' FN PACKAGE
(TOP VIEW)
eo U<{
125 °C. The SN74' family is characterized for opera- U<{uueo
tion from 0 °C to 70 °C. Zit!) Z > t!)
A1 NC
logic symbol NC NC
'AS758 'AS759 B1
NC
B2
e1 q-ouq-c")
<{zzeoeo
t!)
B2
NC- No Internal connection en
B3 !::
FUNCTION TABLE :::J
B4 U
INPUTS
GBA
'AS758 'AS759 a:
GAB
L L A to B A to B
U
logic diagrams (positive logic) H H B to A B to A en
'AS758 'AS759 H L Isolation Isolation ~
L H
Latch A and B
(A=B)
Latch A and B
(A=B)
c
2:
~
en
..J
~

283
Thb document contain. information on • product under
development. Texa.ln.trumenta re •• rve. the right to TEXAS 2-495
chenge or discontinue thI. product without notice. INSTRUMENTS
QUADRUPLE BUS TRANSCEIVERS WITH OPEN-COLLECTOR OUTPUTS
Operating free-air temperature range: SN54AS758, SN54AS759 . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
, SN74AS758,SN74AS759 . . . . . . . . . . . . . . . . . . . . . . . . . . 00et0700e

SN54AS758 SN74AS758
SN54AS759. SN74AS759 UNIT
VIL Low-level input voltage O.a O.B V
SN54AS758 SN74AS758
-
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
10H Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 rnA
Vee = 4.5 V. 10L = 48 rnA 0.55
VOL V
Vee = 4.5 V, 10L = 64 rnA 0.55
l> Control inputs Vee = 5.5 V. VI =7V
r- II
0.1 0.1
rnA
(J) A or B ports Vee = 5.5 V, Vl = 5.5 V 0.1 0.1
l> IIH
A or B portst
Vee = 5.5 V, VI = 2.7V IIA
:2 Control inputs -0.1 -0.1
C IlL
A or B portst
Vee = 5.5 V, VI = 0.4 V -0.1 -0.1
rnA
l> 'AS758
Outputs high 18 18
(J) Outputs low 34 34
ICC Vee = 5.5 V rnA
("') Outputs high 28 28
'AS759
Outputs low 34 34
:lJ values are at Vee = 6 V, TA
("') *tAliFor tYPical = 26°e
I/O ports, the parameters IIH and IlL include the off-state output current.
c Additional Information on these products can be obtained from the factory as it becomes available.
=t
(J)
1283
2-496 TEXAS
INSTRUMENTS
QUADRUPLE BUS TRANSCEIVERS WITH OPEN·COLLECTOR OUTPUTS
,AS758 switching characteristics (see Noto 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
I
SN54AS758 SN74AS758
tpLH 20 20
A or B BorA ns
tPHL 6 6
tpLH 23 23
GBA A ns
tpHL 9 9
tpLH 22 22
GAB B ns
tpHL 8 8

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54AS759 SN74AS759
MIN TYPt MAX MIN TVPt MAX
tpLH 20 20
A or B BorA ns
tpHL 6 6
tpLH 23 23
GBA A ns
tpHL 9 9
tpLH 22 22
tpHL
GAB B
8 8
ns en
NOTE 1: For load circuit and voltage waveforms, see page 1-1 2.
!::
::J
U
a:
U
en
<t
c
;2
<t
en
....I
<t
1283
TEXAS 2-497
INSTRUMENTS
-
l>
r-
en
l>
2'
C
l>
en
Q
::xJ
(")
C
~
en
2-498
OCTAL BUFFERS AND LINE DRIVERS WITH OPEN·COLLECTon OUTPUTS
DECEMBER 1983
o Open-Collector Outputs Drive Bus Lines or SN54AS760 .•• J PACKAGE

Buffer Memory Address Registers SN74AS760 .•. N PACKAGE
ITOPVIEW)
G Eliminates the Need For 3-State Overlap Pro-
tection 1(3 Vee
1A1 2<3
«I» P-N-P Inputs Reduce DC Loading
2Y4 1Y1
• Package Options Include ,Both Plastic and 1A2 2A4
Ceramic Chip Carriers in Addition to Plastic 2Y3 1Y2
and Ceramic DIPs 1A3 2A3
2Y2 1Y3
1A4 2A2
Reliability
2Y1 1Y4
o Open-Collector Version of ' AS244 GND 2A1
description SN54AS760 •.• FH PACKAGE

SN74AS760 .•. FN PACKAGE
These octal buffers and line drivers are designed
ITOPVIEW)
specifically to improve both the performance and
density of three-state memory address drivers, clock
drivers, and bus-oriented receivers and transmitters
by eliminating the need for 3-state overlap protec-
tion. Taken together with the 'AS756 and 'AS757, 1A2 1 Y1
these devices provide the choice of selected com- 2Y3 2A4
binations of inverting outputs, symmetrical G (active- 1A3 1Y2
low input control) inputs, and complementary G and 2Y2 2A3
G inputs. lA4 lY3
The SN54AS760 is characterized for operation over
the full military temperature range of - 55 °e to en
125 °e. The SN74AS760 is characterized for opera- !::
tion from 0 °e to 70 o e. ::::>
u
functional block diagram (positive logic) logic symbol a:
U
en
(2) 1A1 1V1
<C
1A1
(18)
1Y1 2A1 (11) >-_-+_.:..:(9~) 2Y1
1A2 1V2 C
1A3 1V3 2:
(4) (16) 2A2 (13) >-_-+_.:..:(7~)
1A2 1Y2 2Y2
1A4 1Y4 <C
(6) (14) (15) ~_--t---,-(5..;..) 2Y3
en
1A3 1Y3 2A3 ..oJ
<C
(8) (12) (17) >-_ _ _..;,,(3...;..) 2Y4 2A1 2Y1
1A4 1Y4 2A4
2A2 2Y2
2A3 2Y3
2A4 (17) (3)
Pin numbers shown are for J and N packages 2Y4

1283
This document contains infonnation on a product under
development. Taxas Instruments reserves the right to TEXAS 2-499
OCTAL BUFFERS AND LINE DRIVERS WITH OPEN-COLLECTOR OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .,7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS760 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to ,125 °e
SN74AS760 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe

SN54AS760 SN74AS760
UNIT
VIL Low-Il{,el input voltage 0.8 0.8 V
SN54AS760 SN74AS760
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V,
10H Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 rnA
If) VOL
Vee
Vee
= 4.5 V.
= 4.75 V.
10L = 48 rnA
10L = 64 rnA
0.55
0.55
V
»
r-
II
IIH
Vee
Vee
= 5.5 V.
= 5.5 V.
VI = 7 V
VI = 2.7V
0.1
20
0.1
20
rnA
IJA
C/) IlL Vee = 5.5 V. VI = 0.4 V -0.3 -0.3 rnA
»
2:
ICC Vee = 5.5 V
I
I
Outputs high
Outputs low
22
60
22
60
rnA
C
»
C/) Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Q FROM TO RL = 500 Q.
PARAMETER UNIT
:z:J (INPUT) (OUTPUT) TA = MIN to MAX
o SN54AS760 SN74AS760
c MIN TYPt MAX MIN TYPt MAX
=i
C/)
tpLH
A Y
20 20
ns
tpHL 6 6
tpLH 22 22
G Y ns
tpHL 8 8
Additional Information on these products can be obtain~d from the factory as It becomes available.
1283
2-500 TEXAS
INSTRUMENTS
DECEM8ER 1983
o Included Among the Package Options Are SN54AS' •.• JPACKAGE

20-Pin DIPs and Both Plastic and Ceramic SN74AS' •.. N PACKAGE
Chip Carriers (TOP VIEW)
o 'AS762 Has True and Complementary 1<3 VCC

Outputs 1A1 2(3/2G*
2Y4 1Y1
o 'AS763 Has Complementary G and G Inputs 1A2 2A4
o Open-Collector Outputs Drive Bus Unes or 2Y3 1Y2
Buffer Memory Address Registers 1A3 2A3

2Y2 1Y3
o Eliminates the Need for 3-State Overlap 1A4 2A2
Protection 2Y1 1Y4
o
.,
Current Sinking Capability Up to 64 mA GND 2A1

Reliability SN54AS' •.• FH PACKAGE
SN74AS' •.. FN PACKAGE
(TOP VIEW)
description ~
<.:I
These octal buffers and line drivers are designed ~
N
< 1<.:1 >tll~
N
specifically to improve the performance of three-
state memory address drivers, clock drivers, and bus-
oriented receivers and transmitters by eliminating the 1A2 1Y1
need for 3-state overlap protection. The designer has 2Y3
a choice of selected combinations of inverting and 1A3 1Y2
non inverting outputs, symmetrical G (active-low out- 2Y2 2A3
put control) inputs, and complementary G and G 1Y3
inputs.
en
The SN74AS762 and SN74AS763 can be used to
!:::
drive terminated lines down to 1 33 ohms.
=>
The SN54AS762 and SN54AS763 are character-
·2"0" for 'AS762 or 2G for 'AS763
u
ized for operation over the full military temperature a:
range of - 55 ac to 125 ac. The SN74AS762 and u
SN74AS763 are characterized for operation from
oac to 70 aC.
en
<t
logic symbols C
2
'AS762 'AS763 <t
en
...I
1Al lY1 <t
lA2 lY2
lA3 lY3
1A4 lA4 lY4
2G
(9) 2Yl 2Y1

(7) 2Y2 2A2 2Y2
(5) 2Y3 2A3 2Y3
(3) 2Y4 2A4 2Y4

This document contain. information on 8 product W1CIar
development. Taxa, Instruments reserves the right to
TEXAS . 2-501
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS762, SN54AS763 . . . . . . . . . . . . . . . . . . , ... - 55 DC to 125 DC
SN74AS762,SN74AS763 . . . . . . . . . . . . . . . . . . . . . . . . . . ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 DC to 1 50 DC

SN54AS762 SN74AS762
VIH High-level input voltage 2 2 ·V
SN54AS762 SN74AS762
IIIfJ VIK
IOH
Vee
Vee
Vee
=
=
4.5 V,
= 4.5 V,
4.5 V,
II
VOH
IOL
= -18 mA
= 5.5 V
= 48 mA
-1.2
0.1
0.55
-1.2
0.1
V
mA
l> VOL
Vee = 4.5 V, IOL = 64 mA
V
r- 0.55
en II Vee
Vee
= 5.5 V,
= 5.5 V,
VI = 7 V
VI = 2.7 V
0.1 0.1 mA
IIH 20 20 p.A
l> IlL Vee = 5.5 V, VI = 0.4 V -0.5 -0.5 mA
:2 Outputs high 21 21
C 'AS762 Vee = 5.5 V mA
Outputs low 55 55
ICC
l> =
Outputs high 17 17
en 'AS763 Vee 5.5 V
Outputs low 52 52
mA
(") tAli typical values are at Vee = 5 V, TA = 25°e

::xJ
(")
c
=i
en
1283
2-502 TEXAS
INSTRllMENTS
, AS7 62 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 60 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
(INPUT) (OUTPUT) . TA = MIN to MAX
SN54AS762 SN74AS762
tpLH 20 20
1A 1V ns
tpHL 6 6
tpLH 20 20
2A 2V ns
tpHL 6 6
tPLH 22 22
G 1V ns
tPHL 8 8
tpLH 22 22
G 2V ns
tpHL 8 8

Vcc = 4.5 V to 6.6 V.
CL = 60 pF.
FROM TO RL = 600 Q.
PARAMETER UNIT
SN54AS763 SN74AS763
tpLH 20 20
A V ns
tPHL 6 6
tpLH 22 22
G V ns
tpHL 8 8 en
tpLH
G V
23 23
ns t::
tpHL 9 9 ::>
tAli typical values are at Vee = 5 V. TA = 25°e. u
Additional information on these products can be obtained from the factory as it becomes available. a:
u
en
«
c
:2:
«
en
...J
«
1283
TEXAS 2-503
INSTRUMENTS
II1II
l>
r-
en
l>
:2
C
l>
·,en
(")
::IJ
(")
c
=t
en
2-504
TRIPLE 4·INPUT AND/NAND DRIVERS
D2661. DECEMBER 19B2-REVISED DECEMBER 19B3
SN54AS800 •••• J PACKAGE

• Less than 0.5 ns Skew between True and
SN74AS800 •••• N PACKAGE
Complementary Outputs
(TOP VIEW)
• High Capacitive-Drive Capability
1A VCC
• Current Sink/Source Capability Up to 48 rnA 2A 1D
• Approximately 35% Improvement in AC 2B 1C
Performance over Schottky TTL 2C 1B
2D 1Y
• Package Options Include DIPs and Both 3A 1Z
Plastic and Ceramic Chip Carriers 3B 2Z
• Suitable for Use in Applications such as: 3C 2Y
- Differential Line Drivers 3D 3Y
- Complementary Input Circuit for Decoders GND 3Z
and Code Converters
- Symmetrical Complementary Clock SN54AS800 •••• FH PACKAGE
Generators SN74AS800 ••.• FN PACKAGE
(TOP VIEW)
Reliability u
III
N
«N «~ >u c
~
2C 1C
2D 1B
3A 1Y
3B 1Z
3C 2Z
c
M
C
Z
N
M
>-
M N
>- en
t!l
!::
::::>
u
a:
description u
The 'AS8aa is especially suitable for symmetrical complementary clock-generator applications due to the delay time in en
either function (AND/NAND) being typically 4 ns with less than 0.5 ns skew between the true and complementary <t
outputs. Elimination of decode spikes in symmetrical decoder and code converter applications, and the high capacitive- C
drive capability coupled with high current-sinking capability (48 mAl, make the device useful for applications such as a 2
decoder or differential line driver. <t
The SN54AS80a is characterized for operation over the full military temperature range of -55°e to 125°e. The
en
....I
SN74AS800 is characterized for operation from aOe to 7aoe. <t
1282 - PRODUCT PREVIEW Copyright © 1982 by Texas Instruments Incorporated

ThIs document contain. information on a product under
development. Texa.lnstruments ..serves the right to
chang. or discontinue this product without nollce.
TEXAS 2-505
INSTRUMENTS
TRIPLE 4-INPUT AND/NAND DRIVERS
logic symbol
(1 )
1A &[> (16)
(17) 1Y
18
(18)
1C t-.... (15)
(19) 1Z
10
(2)
2A (13)
(3) 2Y
28
(4)
2C t-.... (14)
(5) 2Z
20
(6)
3A (12)
(7) 3Y
38
(8)
3C "- (11)
(9) 3Z
3D
Pin numbers shown are for J and N packages. positive logic: Y = ABeD
z = AEi'C'5
IIIfJ
»
~
absolute maximum ratings over free-air temperature range (unless otherwise noted)
tJ) Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
»
:2
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74AS800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 DC to 70 DC
C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 DC to 1 50 DC
»
tJ) recommended operating conditions
Q SN54AS800 SN74AS800
UNIT
:JJ MIN NOM MAX MIN NOM MAX
(") Vee Supply voltage 4.5 5 5.5 4.5 5 5.5 V
c: VIH High-level input voltage 2 2 V
=i
tJ)
VIL
IOH
Low-level input voltage
High-level output current
0.8
-40
0.8
-48
V
rnA
1282
2-506 TEXAS
INSTRUMENTS
TRIPLE 4·INPUT AND/NAND DRIVERS
SN54AS800 SN74AS80Q
-18 rnA -1.2 -1.2 V
Vee = 4.5 V. 10H = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40 rnA 2
Vee = 4.5 V. 10H = -48 rnA 2
Vee = 4.5 V. 10L = 40 rnA 0.25 0.5
VOL V
Vee = 4.5 V. 10L = 48 rnA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 iJ.A
IlL Vee = 5.5 V. VI = 0.4 V -0.3 -0.3 rnA
lot Vee = 5.5 V. Vo = 2.25 V -150 -150 rnA
ICC Vee = 5.5 V. 13 13 rnA
typical values are at Vee = 5 V. T A = 25°e.
t All

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54AS800 SN74AS800
MIN TYPt MAX MIN· TYPt MAX
tpLH 3.5 3.5
Z ns
tPHL
A.B.e. or D
3.5 3.5 en
tPLH
tpHL
Y
3
4
3
4
ns !::
:l
NOTE1: For load circuit and voltage waveforms. see page 1-12. U
a:
C3
en
<t
C
2:
<t
en
....I
<t
1283
TEXAS 2-507
INSTRUMENTS
- l>
r-
C/)
l>
2
C
l>
C/)
Q
::D
('")
c:
=i
rn
2-508
TRIPLE 4·INPUT ORINOR LINE DRIVERS
D2662, DECEMBER 1962-REVISED DECEMBER 1963
• True and Complementary Outputs SN54AS802 •••• J PACKAGE

SN74ASS02 •••• N PACKAGE
• Less than 0.5 ns Skew between Outputs (TOP VIEW)
• High Capacitive Drive Capability

1A vcc
2A 1D
o Approximately 35% Improvement in AC 2B 1C
Performance over Schottky TTL 2C 1B
2D 1Y
• Current Sink/Source Capability Up to 48 mA
3A 1Z
o Package Options Include Plastic and Ceramic 3B 2Z
DIPs as well as Both Plastic and Ceramic 3C 2Y
Chip Carriers 3D 3Y
GND 3Z
o Designed Specifically for Use in Applications
such as:
- Symmetrical Complementary Clock SN54AS802 •••. FH PACKAGE
Generators SN74AS802 •••• FN PACKAGE
_. Complementary Input Circuit for (TOP VIEW)
Decoders and Code Converters U
- Differential Line Drivers
<0
N
<
N ~ >Uc
~

Reliability 2C 1C
2D 1B
3A
3B
3C
c
M
c N
M
>-
M N>-
Z
t:l
en
t::
description :>
(.)
The' AS802 is uniquely suitable for symmetrical complementary clock-generator applications due to the delay time in
either function (OR/NOR) being typically 4 ns with less than 0.5 ns skew between the true and complementary outputs.
a:
Elimination of decode spikes in symmetrical de~oder and code converter applications. and the high capacitive drive
U
capability coupled with high cu~rent-sinking capability (48 mAl. make the device useful for applications such as a en
decoder or differential line driver. <C
The SN54AS802 is characterized for operation over the full military temperature range of -55°C. to 125°C. The
C
SN74AS802 is characterized for operation from O°C to 70°C.
2
<C
en
....I
<C
PRODUCT PREVIEW Copyright © 1982 Texas Instruments Incorporated

1282
ThIs ~t contains information on. product under
development. Texa.lnstruments reserve. the right to
chang. or discontinue this product without notlc •.
TEXAS 2-509
INSfRUMENTS
TRIPLE 4·INPUT OR/NOR LINE DRIVERS
logic symbol
(1 )
lA ;;;'1[> (16)
(17) lY
18
(18)
lC (15)
10
(19)
(2)
"'" lZ
2A (13)
(3) 2Y
28
(4)
2C t-... (14)
(5) 2Z
20
(6)
3A (12)
(7) 3Y
38
(8)
3C (11)
30
(9)
"'" 3Z
Y=A+B+C+O
Pin numbers shown are for J and N packages. positive 'logic:
Z=A+B+C+O
IB
l>
r-
rn absolute maximum ratings over operating free·air temperature range (unless otherwise noted)
l> Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
2 Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
C Operating free-air temperature range: SN54AS802 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
l> SN74AS802 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ooew70oe
rn Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 1 50 °e
n recommended operating conditions
::D
n SN54ASS02 SN74ASS02
c MIN NOM MAX MIN NOM MAX
UNIT
~ Vee Supply voltage 4.5 5 5.5 4.5 5 5.5 V

rn VIH High-level input voltage 2 2 V
VIL Low-level input voltage O.S O.S V
IOH High-level output current -40 -4S mA
1282
2-510 TEXAS
INSTRUMENTS
TRIPLE 4·INPUT ORINOR LINE DRIVERS
SN54AS802 SN74AS802
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
Vee = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. IOH = -40 rnA 2
Vee = 4.5 V. IOH = ":48 rnA 2
Vee =4.5 V. 10L = 40 rnA 0.25 0.5
VOL V
Vee = 4.5 V. 10L = 48 rnA 0.35 0.5
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 IJA
IlL Vee = 5.5 V, VI = 0.4 V -0.3 -0.3 rnA
lot Vee = 5.5 V. Vo = 2.25 V -150 -150 rnA
ICC Vee = 5.5 V. 20 20 rnA
tAli tYPical values are at Vee = 5 V. TA = 25°e.

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
SN54AS802 SN74AS802
tpLH 3.5 3.5
Y ns
tpHL 4.5 4.5
A.B.e.D (J)
tpLH 4 4
tpHL
Z
5 5
ns
!=
t All tYPical values are at Vee = 5 V, TA = 25°e. :::J
NOTE 1: For load circuit and voltage waveforms, see page 1-12. U
a:
C3
(J)
<C
c
Z
<t
(J)
...J
<t
1283
TEXAS 2-511
INSlRUMENlS
- l>
r-
C/)
l>
2:
C
l>
C/)
Q
:::D
(')
c:
=i
C/)
2-512
TYPES SN54ALS80' SN54AS804A, SN74ALS80' SN74AS804A
HEX 2·INPUT NAND DRIVERS
• High Capacitive Drive Capability SN54ALS804,SN54AS804A ... JPACKAGE

SN74ALS804. SN74AS804A •.. N PACKAGE
• 'ALSB04 Has Typical Delay Time of 4 ns (TOP VIEW)
(CL = 50 pF) and Typical Power Dissipation of
3.4 mW per Gate 1A Vee
1B 6B
• 'ASB04A Has Typical Delay Time of 2.6 ns
1Y 6A
(CL = 50 pF) and Typical Power Dissipation 'of
2A 6Y
Less than 9 mW per Gate
2B 5B
• Package Options Include Both Plastic and Ceramic 2Y 5A
Chip Carriers in Addition to Plastic and Ceramic 3A 5Y
DIPs 3B 4B
3Y 4A
GND 4Y
Reliability
description
These devices contain six independent 2-input NAND
drivers. They perform the Boolean functions Y = A· B SN54ALS804. SN54AS804A ..• FH PACKAGE
or Y = A + B in positive logic. SN74ALS804. SN74AS804A ... FN PACKAGE
(TOP VIEW)
The -1 version of the SN74ALS804 parts is identical
to the standard version except that the recommend-
ed maximum IOL is increased to 48 milliamperes.
There is no -1 version of the SN54ALS804 parts.
The SN54ALS804 and SN54AS804A are character- 2A

ized for operation over the full military temperature 2B
range of - 55 °e to 125 °e. The SN74ALS804 and 2Y 5B
SN74AS804A are characterized for operation from 3A 5A
ooe to 70 oe. 3B
en
!::
FUNCTION TABLE (each driver) =>
(.)
INPUTS OUTPUT a:
A B V (.)
H H L
L X H
en
X L H
<C
C
logic symbol 2
<C
en
18 ..oJ
2A <C
28
3A
38
4A
48
5A
58
6A
68

483
TEXAS INSTRUMENTS 2-513
INCORPORATED
TYPES SN54ALSBD4, SN74ALSBD4
Supply voltage. Vee .......... , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '...... 7 V
Operating free-air temperature range: SN54ALS804 . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74ALS804 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODeM70 De

UNIT
12 24
48t
tThe extended limit applies if Vee is maintained between 4.75 V and 5.25 V.
The 48 mA limit applies for the SN74ALS804-1 only.
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
lID Vee = 4.5 V to 5.5 V.

Vee = 4.5 V.
IOH = -0.4 mA
IOH = -3 mA
Vee- 2
2.4 3.2
Vee- 2
2.4 3.2
V
»
r-
VOH
Vee = 4.5 V.
Vee = 4.5 V.
10H = -12 mA
IOH = -15 mA
2
2
en Vee = 4.5 V. 10l = 12 mA 0.25 0.4 0.25 0.4
»
2
Val Vee = 4.5 V. 10l = 24 mA
(lOl = 48 mA for -1 version)
0.35 0.5
V
II Vee = 5.5 V, VI =,7 V 0.1 0.1 mA

C
IIH Vee = 5.5 V. VI = 2.7V 20 20 ~A
»
en III Vee = 5.5 V. VI = 0.4 V -0.1 - -0.1 mA
lo§ Vee = 5.5 V. Va = 2.25 V -30 -112 -30 -112 mA
'('") leeH Vee = 5.5 V. VI = OV 0.9 2.5 0.9 2.5 mA
leel Vee = 5.5 V. VI = 4.5 V 7 12 7 12 mA
JJ
('") tAli typical values are at Vee = 5 V, T A = 25 DC.
c §The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
=i switching characteristics (see Note 1)

en VCC = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
MIN MAX MIN MAX
tplH 2 8 2 6
A or B Y ns
tpHl 2 9 2 7
NOTE 1: For load circuit and voltage waveforms. see page 1-12,
1283
2-514 TEXAS
INSTRUMENTS
TYPES SN54ASB04A, SN74ASB04A
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS804A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AS804A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C

UNIT
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. 10H = -2 mA Vee- 2 Vec- 2
Vee = 4.5 V. 10H =
-3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H =
-40mA 2
Vee = 4.5 V. 10H = -48 mA 2
Vee = 4.5 V. 10L = 40 mA 0.25 0.5
VOL
= 4.5 V. 10L = 48 mA
V en
II
Vee
Vee = 5.5 V. VI = 7 V 0.1
0.35 0.5
0.1 mA t:
= 5.5 V. VI = 2.7 V ::::>
IIH
IlL
Vee
Vee = 5.5 V. VI = 0.4 V
20
-0.5 -0.5
20 /J A
mA
uc:::
10* Vee = 5.5 V. Vo = 2.25 V -135 -135 mA
leeH Vee = 5.5 V. VI = OV 2.5 4 2.5 4 mA u
leeL Vee = 5.5 V. VI = 4.5 V 16 27 16 27 mA en
i The output conditions have been chosen to produce a current that closely approximates one half of the true short-Circuit output current, lOS.
<t
C
Vcc = 4.5 V to 5.5 V.
<t
CL = 50 pF. en
..J
FROM TO RL = 500 Q.
PARAMETER
UNIT <t
MIN MAX MIN MAX
tpLH 2 4.5 2 3.5
A or B Y ns
tpHL 2 4.5 2 3.5
1283
TEXAS 2-515
INSTRUMENTS
2-516
TYPES SN54ALS805. SN54AS805A. SN74ALS805. SN74AS805A
HEX 2·INPUT NOR DRIVERS
02661. DECEMBER 1982- REVISED DECEMBER 1983
• High Capacitive Drive Capability SN54ALS805. SN54AS805A ... J PACKAGE

SN74ALS805. SN74AS805A ... N PACKAGE
• •ALS805 Has Typical Delay Time of 4.2 ns
(TOP VIEW)
o •AS805A Has Typical Delay Time of 2.6 ns 1B 6B
(CL = 50 pF) and Typical Power Dissipation of 1Y 6A
1 2 mW per Gate 2A 6Y
26 56
• Package Options Include Both Plastic and Ceramic 2Y 5A
DIPs 38 48
• Dependable Texas Instruments Quality and 3Y 4A
Reliability GND 4Y
description
These devices contain six independent 2-input NOR
drivers. They perform the Boolean functions SN54ALS805,SN54AS805A ••. FHPACKAGE
Y = A+B or Y = A'Bin positive logic. SN74ALS805, SN74AS805A ... FN PACKAGE
(TOP VIEW)
The -1 version of the SN7 4ALS80 5 parts is identical
to the standard version except that the recommend- U
>-co«Uco
ed maximum IOL is increased to 48 milliamperes. .-.-.->(0
There is no -1 version of the SN54ALS805 parts.
The SN54ALS805 and SN54AS805A are character- 6A

ized for operation over the full military temperature 6Y
range of - 55 De to 125 De. The SN74ALS805 and 5B
SN74AS805A are characterized for operation from 5A
oDe to 70 De. 5Y
FUNCTION TABLE (each driver)
INPUTS OUTPUT
A B y
H X L
X H L
L L H
logic symbol
TEXAS 2-517
INSTRUMENTS
TYPES SN54ALSB05, SN74ALSB05
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS805 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00e~700e

SN54ALS80S SN74ALS80S
UNIT
Vee Supply voltage 4.5 5 5.S 4.S 5 5.5 V
12 24
10L Low·level output current mA
48t
tThe extended limit applies if Vee is maintained between 4.75 V and 5.25 V.
The 48 rnA limit applies for the SN74ALS805-1 only.
SNS4ALS80S SN74ALS80S
VIK- Vee = 4.5 V, II =
-18 mA. -1.5 -1.5 V
Vee = 4.5 V to 5.S V, 10H = -0.4 mA Vee- 2 Vee- 2
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, 10H = -12 mA 2
Vee = 4.5 V, 10H = -15 mA 2
Vee = 4.5 V, 10L = 12 mA 0.2S 0.4 0.25 0.4
VOL Vee = 4.5 V, 10L = 24 mA V
0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 IJA
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI = aV 2 4 2 4 mA
leel Vee = 5.5 V, VI = 4.S V 8 14 8 14 mA
tAli typical values are at Vee = 5 V, T A = 25 DC.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.

VCC = _4.S V to 5.S V,
cL = SO pF,_
FROM TO RL = SOO Q,
PARAMETER UNIT
(INPUT) I (OUTPUT) TA = MIN to MAX
SNS4ALS80S SN74ALS80S
MIN MAX MIN MAX
tpLH 2 8 2 6
A or B y ns
tpHl 2 9 2 7
1283
2-518 TEXAS
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ASB05A ........ '. . . . . . . . . . . . . . . . . -...... - 55°C to 125°C
SN7 4ASB05A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C
recommended _operating conditions

SN54ASB05A SN74ASB05A
UNIT
electrical characteristics over recommended operating free-air temperature ,range (unless otherwise noted)
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
Vee = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. IOH = -40 rnA 2
Vee = 4.5 V. IOH = -48 rnA 2
Vee = 4.5 V. IOL = 40 rnA 0.25 0.5
VOL V (J)
0'.5
II
Vee = 4.5 V.
Vee = 5.5 V.
IOL = 48 rnA
VI = 7 V 0.1
0.35
0.1 rnA t:
:::>
IIH Vee =5.5 V. VI = 2.7V 20 20 /-LA
u
IlL
IO~
Vee = 5.5 V.
Vee = 5.5 V.
VI = 0.4 V
Vo = 2.25 V -135
-0.5
-135
-0.5 rnA
rnA
a:
leeH Vee = 5.5 V. VI = 0 V 5 9 5 9 rnA u
leel Vee = 5.5 V. VI = 4.5 V 18 32 18 32 rnA (J)
t The output conditions have been chosen to produce a current that closely, approximates one half of the true short-circuit output current, lOS'
«
c
switching characteristics (see Note 1) 2
Vee = 4.5 V to 5.5 V.
«
CL = 50 pF.
(J)
..J
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL = 500Q.
TA = MIN to MAX
UNIT «
SN54ASB05A SN74ASB05A
MIN MAX MIN MAX
tPLH 1 4.5 1 4
A or B Y ns
tpHL 1 4.5 1 4
NOTE 1: For load circuit and voltage waveforms, see page 1-1 2.
1283
TEXAS 2-519
INSTRUMENTS
iifJ
l>
r-
en
l>
:2
C
l>
en
Q
::D
o
c:
=i
en
2-520
TYPES SN54ALSBOB, SN54ASBOBA, SN74ALSBOB, SN74AS808A
HEX 2·INPUT AND DRIVERS
o High Capacitive Drive Capability SN54ALSBOB. SN54ASBOBA , .• J PACKAGE

SN74ALSBOB. SN74ASBOBA ..• N PACKAGE
o 'ALS80B Has Typical Delay Time of 4.B ns ITOPVIEW)
o 'ASBOBA Has Typical Delay Time of 3.2 ns 1B 6B
(CL = 50 pF) and Typical Power Dissipation of 1Y 6A
Less than 13 mW per Gate 2A 6Y
2B 5B
o Package Options Include Both Plastic and Ceramic 2Y 5A
DIPs 3B 4B
o Dependable Texas Instruments Quality and 3Y 4A
Reliability , GND 4Y
description
These devices contain six independent 2-input AND SN54ALSBOB. SN54ASBOBA ... FH PACKAGE
drivers. They perform the Booleim functions Y = A· B SN74ALSBOB. SN74ASBOBA •.. FN PACKAGE
or Y = A+ B in positive logic. ITOPVIEWI
The -1 version of the SN74ALSBOB parts is identical
to the standard version except that the recommend-
ed maximum IOL is increased to 4B milliamperes.
There is no -1 version of the SN54ALSBOB parts.
6A
The SN54ALSBOB and SN54ASBOBA are character- 6Y
ized for operation over the full military temperature 5B
range of - 55 °e to 125 °e. The SN74ALSBOB and 5A
SN74ASBOBA are characterized for operation from (J)
5Y
ooe to 70 oe. !::
FUNCTION TABLE leach driver)
::l
U
INPUTS OUTPUT
a:
A B Y U
H H H (J)
L X L <C
X L L
c
logic symbol
z
<C
1A (J)
18 ..J
<C
6A (17) 6Y
68 (19)

483
TEXAS 2-521
INSTRUMENTS
HEX 2·INPUTAND DRIVERS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALSBOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALSBOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . '.' . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C

UNIT
12 24
IOl low-level output current mA
48t
tThe extended limit applies If Vee IS maintained between 4.76 V and 6.26 V.
VIK Vee - 4.5 V, II = -18 mA -1.5 -1.5 V
Vee - 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, IOH = -12 mA 2
Vee - 4.5 V, IOH - -15 mA 2
Vee = 4.5 V, IOl = 12 mA 0.25 0.4 0.25 0.4
VOL Vee = 4.5 V, 10l = 24 mA V
0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI- 2.7V 20 20 j.lA
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lo§ Vee - 5.5 V, Vo - 2.25 V -30 -112 -30 -112 mA
leCH Vee = 5.5 V, VI = 4.5 V 3 6 3 6 mA
leCl Vee - 5.5 V, VI - 0 V 8 16 8 16 mA
iAil typical values are at Vee = 6 V. T A = 26 DC.
§The output conditions have been chosen to produce a current that closely approximates one half of. the true short-circuit output current, lOS'

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
FROM TO RL = 500 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tplH 2 10 2 8
A or B Y ns
tpHl 2 10 2 8
1283
2-522 TEXAS
INSTRUMENlS
TYPES SN54ASBDBA, SN74ASBDBA
HEX 2·INPUT AND DRIVERS
Supply voltage, Vee ................ _......................................-........ 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS808A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN7 4AS808A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70 °C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 °C

SN54ASBOBA SN74ASBOSA
UNIT
VIL Low-level input voltage O.B O.B V
10H High-level output current -40 -4B rnA
SN54ASBOBA SN74AS80BA
..
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
Vee = 4.5 V. IOH = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40 rnA 2
Vee = 4.5 V. 10H = -48 rnA 2
= 4.5 V. IOL = 40 rnA
VOL
Vee
Vee = 4.5 V. IOL = 48 rnA
0.25 0.5
V en
II Vee = 5.5 V. VI = 7 V 0.1
0.35 0.5
0.1 rnA t=
IIH Vee = 5.5 V. VI = 2.7V 20 20 IJ.A
::>
()
= 5.5 V. VI = 0.4 V
IlL
10*
Vee
Vee = 5.5 V._ Va = 2.25 V -135
-0.5
-135
-0.5 rnA
rnA
a:
leeH Vee = 5.5 V. VI = 4.5 V 6.5 11 6.5 11 rnA
()
leel Vee = 5.5 V. VI =0 V 19 32 19 32 rnA en
All typical values are at VCC = 5 V. T A = 25°C.
*t The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
«
c
VCC = 4.5 V to 5.5 V.
«
CL = 50 pF. en
-I
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL= 500 Q.
TA = MIN to MAX
UNIT «
SN54ASBOBA SN74ASB08A
MIN MAX MIN MAX
tpLH 1 6 1 5
A or 8 Y ns
tPHL 1 6 1 5
1283
TEXAS 2-523
INSTRUMENTS
..
l>
r-
(J)
l>
2
C
l>
(J)
S2
::u
o
c:
=i
(J)
2-524
10·BIl BUS INTERFACE FLlp·FLOPS WITH 3·STATE OUTPUTS
o 10·Bit Versions of 'AS574 and 'AS576 with SN54AS821 , •. JT PACKAGE

SN74AS821., . NT PACKAGE
Improved IOH Specifications
(TOP VIEW)
o Ideal for Data Synchronization of Wider oc VCC
Data Paths 10 10
20
o Provides Extra Data Width Necessary for 3D 4 21 30
Wider Address/ Data Paths or Buses with 40 20 40
50 19 50
Parity 60 18 60
70 17 70
o Outputs Have Undershoot Protection 80 9 16 80
Circuitry . 90 10 15 90
100 11 14 100
o Power·Up High·lmpedance State GND 12 13 ClK
o Package Options Include Both Plastic and SN54AS821 ••• FH PACKAGE

Ceramic Carriers in Addition to Plasstic and SN74AS821 . , . FN PACKAGE
Ceramic DIPs (TOP VIEW)
o Buffered Control Inputs to Reduce DC ~elg~~~~

Loading Effects
3D 30
40 40
50
Reliability NC
60
description 70
These 10-bit flip-flops feature three-state

OOOU>ldd
outputs designed specifically for driving highly- mozz..Jocn
[.jrJi~!*~~
~ t:l U ~
capacitive or relatively low-impedance loads.
They are particularly suitable for implementing SN54AS822 •.. JT PACKAGE
SN74AS822 ... NT PACKAGE
wider buffer registers, I/O ports, bidirectional bus
drivers with parity, and working registers. I (TOP VIEW)
en
oc 1 24 VCC !::
The ten flip-flops are edge-triggered D-type flip- 10 2 23 10 ::>
flops. On the positive transition of the clock the ii5 3 22 20
u
Q outputs on the' AS821 will be true, and on the
3D
45
21
20
30
40
a:
'AS822 will be complementary, to the data 50
60
6 19
18
50
60
u
input. 75 17 70 en
A buffered output-control input can be used to 80
95 10
16
15
80
90
«
place the ten outputs in either a normal logic
state (high or low levels) or a high-impedance
100
GNO
11
12
14
13
100
ClK
c
2
state. In the high-impedance state the outputs
neither load nor drive the bus lines significantly.
SN54AS822 .• '. FH PACKAGE «
The high-impedance state and increased drive
SN74AS822 •.• FN PACKAGE
(TOP VIEW)
en
..J
provide the capability to drive the bus lines in a
bus-organized system without need for 1~lelg ~ ~ ~ ~ «
interface or pull-up components. 4 3 2 1 282726
25 30
40
50
NC NC
60
70
80
12 1314151617 18
loIOOU>l d d
CJ)~~Zd ~cn
ADVANCE INFORMATION Copyright © 1983 by Texas Instruments Incorporated

1283
This document contain. information on a new product.
INsrRuMENlS
10·BIT BUS INTERFACE FLlP·FLOPS WITH 3·STATE OUTPUTS
The output control (DC) does not affect the internal operation of the flip-flops. Old data can be retained
or new data can be entered while the outputs are in the high-impedance state.
The SN54AS821 and SN54AS822 are characterized for operation over the full military temperature range
of - 55°C to 125°C. The SN74AS821 and SN74AS822 are characterized for operation from 0 °C to 70 o e.
'AS821 FUNCTION TABLE (EACH FLIP-FLOP' , AS821 logic diagram (positive logic)
INPUTS OUTPUT
OC ClK a a oc ...:,(1.;.;.'_ _ _ _01
l t H H
l t l l
L L X 00
H X X Z
, AS821 logic symbol

20 _(3_'_ _ _ _1---1
Dc
elK
(23) 3D .;,.(4.;..'_ _ _1--1
10 v 10
(22)
20 20
(4) (21)
3D 30
(5) (20)
40 40
(6) (19) 40.;,.(5.;,.'_ _ _1--1
III
50 50
(7) (18)
60 60
(8) (17)
70 70
(9) (16)
l> 80 80
50 ..;.(6_)_ _ _ _1---1
r- 90 90
en 100 100
l>
:2 ' _ _ _ _1---1
60 ..;,(7....
C
l>
en 70 ..;,;(8;,;.'_ _ _ _1---1
~
:tI
(")
c: 80 ..;,;(9;,;.'_ _--1__-1
~
en
90 ...;,11.;..,0.;.,1_ _-+---1
(111
100 ...;..-..;....----1
1283
2-526 TEXAS
INSTRUMENTS
10·BIT BUS INTERFACE FLlp·FLOPS WITH 3·STATE DUTPUTS
'AS822 FUNCTION TABLE lEACH FLIP-FLOP' I AS822 logic diagram (positive logic)
INPUTS OUTPUT
OC ..;1,..;1'_ _ _ _01
oc elK 0 a
l t H l
l t l H
l l X 00
H X X Z
I AS822 logic symbol

20.;.13..;,.'_ _ _t--0I
123'
3D .;.,14..;,.'_ _ _t--0I
10 10
(22\
20 20
(21\
30 30
(20\
40 40
(19\ 40 _15_'_ _ _t-a
50 50
(18\
60 60
(17\
70 70
(16\
80 80 50 _16_)_ _ _t-a
(15\
90 90
(11\ (14\100
105
60 _17_'_ _ _t-a
en
70 18'
!::"
:J
U
a:
80 _19_'_ _---1~~ U
en
«
_ 110' c
90 ~-----1~~
z
«
en
100 Ill) -I
«
Pin numbers shown are for JT and NT packages
1283
TEXAS 2-527
INSTRUMENTS
TYPES SN54AS821, SN54AS822, SN74ASB21, SN74ASB22
Supply voltage, Vee ........................................................ , 7 V
Input voltage .............................................................. 7 V
Voltage applied to a disabled 3-state output. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54AS821, SN54AS822 . . . . . . . . . . . .. - 55°C to 125°C
SN74AS821, SN74AS822 ................ ooe to 70°C
Storage temperature range ......................................... - 65°C to 150°C

SN54AS821 SN74AS821
SN54AS822 SN74AS822 UflilT
tw Pulse duration, eLK high or low 9 8 ns
tsu Setup time, data before eLKt 7 6 ns
th Hold time, data after eLKt 0 0 ns
TA Operating free-air temperature -55 -125 0 70 De

IB PARAMETER TEST CONDITIONS

SN54AS821
SN54AS822
SN74AS821
SN74AS822 UNIT
»
r- V,K Vee = 4.5 V, I, = -18 mA
MIN Typt MAX
-1.2
MIN Typt MAX
-1.2 V
rn Vee = 4.5 V to 5.5 V, IOH = -2 mA Vee- 2 Vee- 2
»
:2
VOH Vee
Vee
= 4.5
= 4.5
V,
V,
IOH = -15 mA
IOH = -24 mA
2.4
2
3.2 2.4
2
3.2 V
c VOL
Vee = 4.5 V, 'OL = 32 mA 0.25 0.5
V
»
rn IOZH
Vee
Vee
= 4.5
= 5.5
V,
V,
'OL
Vo
= 48 mA
= 2.7V 50
0.35 0.5
50 p.A
IOZL vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
(")
Vee = 5.5 V, V, = 7 V 0.1 0.1 mA
::D "
"H Vee = 5.5 V, V, = 2.7 V 20 20 p.A
(") I,L Vee = 5.5 v, V, = 0.4 V -0.5 -0.5 mA
c lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
=i Outputs high 55 88 55 88
rn 'AS821 Outputs low 68 109 68 109
lee Vee = 5.5 V mA
'AS822 Outputs low 68 109 68 109

1283
2-528 TEXAS
INSTRUMENTS
10·BIT BUS INTERFACE FLlp·FLOPS WITH 3·STATE OUTPUTS

Vce = 4.5 V to 5.5 V,
Cl = 50 pF,
R1 = 500 n,
FROM TO R2 = 500 n,
PARAMETER UNIT
SN54AS821 SN74AS821
SN54AS822 SN74AS822
MIN MAX MIN MAX
tPlH 3.5 9 3.5 7.5
elK Any Q ns
tpHL 3.5 11.5 3.5 10.5
tpZH 4 12 4 11
DC Any Q ns
tpZL 4 13 4 12
tpHZ 2 10 2 8
DC Any Q ns
tpZL 2 10 2 8
en
!=
::>
ua:
u
en
<C
C
z
<C
en
..J
<C
1283
TEXAS 2-529
INSTRUMENTS
- l>
r-
en
l>
:2
C
l>
en
~
:J:J
C')
c:
~
en
2-530
• Similar to 'AS574 and' AS576 with Clock SN54AS823 .•. JT PACKAGE

Enable and Clear and Improved IOH
(TOP VIEW)
Specifications
6C VCC
• Ideal for Data Synchronization of Wider 10 10
20 3 20
Data Paths
3D 21 30
20 40
• Provides Extra Data Width Necessary for 19 50
Wider Address/Data Paths or Buses with 18 60
Parity 17 70
80 16 80
• Outputs Have Undershoot Protection 90 10 15 90
ClR 11 14 ClKEN
Circuitry
GND 12 13 ClK
• Power-Up High-Impedance State

SN54AS823 .•. FH PACKAGE
• Buffered Control Inputs to Reduce DC SN74AS823 ... FN PACKAGE
Loading Effects (TOP VIEW)
u
• Package Options Include both Plastic and ~~lg~~~2
Ceramic Carriers in Addition to Plastic and 4 3 2 1 282726
25 30
Ceramic DIPs
50
• Dependable Texas Instruments Quality and NC NC
Reliability 60 60
70 70
80
description 12 1314 151617 18
These 9-bit flip-flops feature three-state outputs

designed specifically for driving highly-capacitive
or relatively low-impedance loads. They are
SN54AS824 ... JT PACKAGE
particularly suitable for implementing wider CJ)
SN74AS824 ••. NT PACKAGE
buffer registers, I/O ports, bidirectional bus
drivers, parity bus interfacing and working
(TOP VIEW) !::
registers.
6C VCC :::>
10 10 ()
With the clock enable (CLKEN) low, the nine D-
20
30
a:
type edge-triggered flip-flops enter data on the 40 40 ()
low-to-high transitions of the clock. Taking 50
60 60 CJ)
CLKEN high will disable the clock buffer, thus
latching the outputs. The 'AS823 has
70
80
<t
noninverting D inputs and the 'AS824 has 95 10 15 90 c
inv~rting 5 inputs. Taking the CLR input low
ClR
GND
11
12
14
13
ClKEN
ClK z
causes the nine Q outputs to go low <t
independently of the clock. SN54AS824 •.. FH PACKAGE
CJ)
-I
A buffered output-control input can be used to
(TOP VIEW)
u <t
place the nine outputs in either a normal logic 1~1~lg ~ ~~ 2
state (high or low levels) or a high-impedance 4 3 2 1 28 2726
state. In the high-impedance state the outputs 25 3a
24 40
neither load nor drive the bus lines significantly. 7 23 5a
50
The high-impedance state and increased drive NC 22 NC
provide the capability to drive the bus lines in a 60 21 60
20 7a
bus-organized system without need for
80
interface or pull-up components.

1283
This document containslnfonnatlon on a product under
INSTRUMENTS
9·81T INTERFACE FLlp·FLOPS WITH 3·STATE OUTPUTS
The output control (DC) does not affect the internal operation of the flip-flops. Old data can be retained
or new data can be entered while the outputs are in the high-impedance state.
of - 55°C to 125°C. The SN74AS823 and SN74AS824 are characterized for operation from 0 °C to 70°C.
FUNCTION TABLES
'AS823 'AS824

OC ClR ClKEN ClK 0 0 OC CLR CLKEN ClK 0 0
L L X X X L L L X X X l
L H L t H H L H L t H L
L H l t L l L H l t L H
L H H X X 00 L H H X X 00
H X X X X Z H X X X X Z
I AS823 logic symbol I AS823 logic diagram (positive logic)
oc ~(..:.!11_ _ _ _ _ _ _ _ _ _-d
CIR.:..:..;:..:........--a
cum;
(23)
10
(22)
~
20
(211 (231 10
30
(20)
40
(19)
):> 50
(18)
r- (17)
60 20 (31 (221 20
OO (16)
70
80
):> (15)
90
:2 3D (41 (211 30
C
):>
40 (51 (201
00 40
n
:JJ (61 (191 50
n 50
c
=4 60
(71 (181 60
00
70 (81 (171 70
80 (91 (161 80
90 (101 (151 90
1283
2-532 TEXAS
INSTRUMENTS
(23)
10
(22)
20 (23) 10
(21)
30
(20)
40
(19)
50
(18) (22) 20
60 20 (3)
(17)
70
(16)
80
(15)
90
30 (4) (21) 30
40 (5) (20) 40
50 (6) (19) 50
60 (7)
(18)
60 IfJII
70
(8) (17) 70 en
!:::
:J
80 (9) (16) 80 U
a:
U
90 (10) (15) 90
en
«
c
Pin numbers shown are for JT and NT packages. z
«
en
...J
«
1283
TEXAS 2-533
INSTRUMENTS
9·81T INTERFACE FLlP·FLOPS WITH 3·STATE OUTPUTS
Supply voltage, Vee ......................................................... 7 V
Input voltage .............................................................. 7 V
Voltage applied to a disabled 3-state output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating applied to a disabled 3-state output .................................... 5.5 V
Operating free-air temperature range: SN54AS823, SN54AS824 . . . . . . . . . . . .. - 55°C to 125°C
. SN74AS823, SN74AS824 ................ ooe to 70°C
Storage temperature range ......................................... - 65°C to 150 °e

SN54AS823 SN74AS823
CLR low
CLK high
CLK low
CLKEN
CLR inactive
Setup time
IIfJ tsu
th
before CLKt
Hold time, data after CLKt

Data
CLKEN
ns
ns
l> TA Operating free-air temperature -55 125 0 70 °c
r-
en
l> Additional information on these products can be obtained from the factory as it becomes available.
:2
o
l>
en
o
:::D
o
c:
~
en
1283
2-534 TEXAS
INSTRUMENTS

SN54AS823 SN74AS823
SN54AS824 SN74AS824
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 mA vee- 2 vee- 2
VOH Vee = 4.5 V, 10H = -15 mA 2.4 3.2 2.4 3.2 V
Vee = 4.5 V, 10H= -24 mA 2 2
VOL Vee = 4.5 V, 10l = 32 mA 0.25 0.5
V
Vee = 4.5 V, 10l = 48 mA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
10Zl Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
IIH Vee = 5.5 V, VI = 2.7 V p.A
10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Outputs high
'AS823 Vee = 5.5 V Outputs low mA
lee
Outputs high

1283
TEXAS 2-535
INSTRUMENTS
9·811 INTERFACE FLlp·FLOPS WITH 3·STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 D.
FROM TO R2 = 500 D.
PARAMETER UNIT
SN54AS823 SN74AS823
SN54AS824 SN74AS824
f max MHz
tPLH 7.5 7.5
CLK Any Q ns
tpHL 9.5 9.5
tpHL CLR Any Q 11 11 ns
tpZH 6 6
OC Any Q ns
tpZL 7 7
tpHZ 6 6
OC Any Q ns
tpLZ 7 7

Additional Information on these products can be obtained from the factory as it becomes available.

It is normal TI practice to name the outputs and other inputs of a Ootype flip-flop and to draw its logic
1111 symbol based on the assumption of true data (0) inputs. Then outputs that produce data in phase with
the data inputs are called Q and those producing complementary data are called Q. An input that causes
»
r-
a Q output to go high or a Q output to go low is called Preset; an input that causes a Q output to go high
or a Q output to go low is called Clear. Bars are used over these pin names (PRE and CLR) if they are
en active-low.
»
:2
The devices on this data sheet are second-source designs and the pin-name convention used by the original
manufacturer has been retained. That makes it necessary to designate the inputs and outputs of the inverting
C circuit 15 and Q. In some applications it may be advantageous to redesignate the inputs and outputs as
»
en
o and Q. In that case, outputs should be renamed as shown below. Also shown are corresponding changes
in the graphical symbol. Arbitrary pin numbers are shown in parentheses.
Q Notice that Q and IT exchange names, which causes Preset and Clear to do likewise. Also notice that the
~ polarity indicators ( ~ ) on PRE and CLR remain since these inputs are still active-low, but that the presence
(') or absence of the polarity indicator changes at 5, Q, and O. Of course pin 5 (Q) is still in phase with the data
c: input 0, but now both are considered active high.
=i
en
ern R
Q
Pi'fE s (5)
Q
CLK C1 eLK C1
0 10 (6)
0 10
Q Q
'PRE s CIA R
1283
2-536 TEXAS
INSTRUMENTS
• Similar to 'AS574 and 'AS576 with Clock SN54AS825 ... JT PACKAGE

Enable, Clear, and Multiple Output Controls SN74AS825 ... NT PACKAGE
(TOP VIEW)
• Improved 10H Specifications ITOPVIEWI
OCl vCC
• Multiple Output Enables Allow Multiuser OC2 OC3
Control of the Interface 10,
20 20
• Outputs Have Undershoot Protection 3D 30
Circuitry 40
50
• Power·Up High·lmpedance State 6D 60
7D 70
• Package Options Include Both Plastic and 8D 10 15 80
ClR 11 14 ClKEN
Ceramic Chip Carriers in Addition to Plastic GND 12 13 ClK
and Ceramic DIPs
• Buffered Control Inputs to Reduce DC SN74AS825 ... FN PACKAGE
Loading Effect (TOP VIEW)

Reliability 4 3 2 1 282726
2D a 20
3D 30
description 40
NC
These 8-bit flip-flops feature three-state outputs 5D 50
designed specifically for driving highly-capacitive 6D 60
70
12 1314 151617 18
particularly suitable for implementing multiuser
registers, I/O ports, bidirectional bus drivers, and
working registers.
With the clock enable (CLKEN) low, the eight 0-
type edge-triggered flip-flops enter data on the
(TOP VIEW)
low-to-high transitions of the clock. Taking
OCl VCC
CLKEN high will disable the clock buffer, thus OC2 OC3
latching the outputs. The 'AS825 has 15 10
noninverting 0 inputs and the ' AS826 has 25 20
35 30
inverting 5 inputs. Taking the CLR input low 40 40
causes the eight. Q outputs 'to go low 50
independently of the clock. 60
70 70
A multiuser buffered output-control input can be 85 10 15 80
PRE 11 14 ClKEN
used to place the eight outputs in either a normal GND 12 13 ClK
logic state (high or low levels). or a high"
impedance state. In the high-impedance state SN54AS826 ... FH PACKAGE
SN74AS826 .•. FN PACKAGE
the outputs neither load nor drive the bus lines
(TOP VIEW)
significantly. The. high-impedance state and N..- UM
increased drive provide the capability to drive the 1~lglg ~ ~Ig S!
bus lines in a bus-organized system without need 4 3 2 1 28 2726
for interface or pull-up components. 20 25 20
30 24 30
23 40
NC 22 NC
50 21 50
60 20 60
19 70
12131415161718
IOIW u °
coO:zz-Jw(X)
0
0...<.:)
"'IZ
u~
u

ThIa document c:ontH1IlnfonnatIan on e product under
development. Te... ln.trument. r...rve. the right to TEXAS 2-537
chang. or dllCQntlnue thI. product without notlc•• INSTRUMENTS
POST OFFICE BOX 225012 • DAllAS. TEXAS 75265
The output controls (OC1, OC2, and OC3) do not affect the internal operation of the flip-flops. Old data can
be retained or new data can be entered while the outputs are in the high-impedance state.
of - 55 DC to 125 DC. The SN74AS825 and SN74AS826 are characterized for operation from 0 DC to 70 DC.
FUNCTION TABLES
'AS825 'AS826

OC* CLR CLKEN CLK 0 Q OC* CLR CLKEN CLK 0 Q
L L X X X L L L X X X L
L H L t H H L H L t H L
L H L t L H L H L t L H
L H H X X 00 L H H X X 00
H X X X X Z H X X X X Z

(11
OCl
Ocl (2)
OC2
OC2 (231
OC3
OC3
CLR
CLR
Ci:i<Ei'J
CLi<E'N
CLK
1221 10
10
141 1211
20 20
lSI 1201 30 (221 10
3D
161 1191 40
40
50
m /lBI
50
IBI 1171
60 60 20 (4) (211
191 1161 20
70 70
1101 (15)
BO BO
3D (5) (20) 30
40 (61 (19) 40
50 m (lB) 50
60 IB) (17) 60
70 (9) (161 70
(10) (15) 80
80
Pin numbers shown are fDr JT and NT packages.
1283
2-538 TEXAS
INSTRUMENTS

OCl~(l~)________________~
OCl - (2)
OC2~(2~3~)----------------~
Oc2 OC3~~--------------~
OC3 (11)
ClR
CLKEN
ClK
10
io (22)
30 10
40
50
60
20~ .E..!..!... 20
70
BO
3D (5) (20)
30
40 (6) (19)
40
(7) (lB)
50 50
(B) (17)
60 60
CJ)
70
(9) (16)
70
!::
=>
u
_ (10) (15)
a:
BD BO
u
CJ)
cd:
absolute maximum ratings over operating free-air temperature range (unless otherwise noted) C
2:
Supply voltage, Vee ................. : ....................................... 7 V cd:
Input voltage .............................................................. 7 V
CJ)
Voltage applied to a disabled 3-state output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V ..J
Operating free-air temperature range: SN54AS825, SN54AS826 . . . . . . . . . . . .. - 55 °e to 125°e
SN74AS825, SN74AS826 ................ ooe to 70 0 e
cd:
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 to 150 °e
1283
TEXAS 2-539
INSTRUMENTS
8-BIT BUS INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS

SN54AS825 SN74AS825
Vil low-level input voltage 0.8 0.8 V,
elR low
elK high
elK low
eLKEN
eLR inactive
Setup time
tsu Data ns
before elK t
elKEN
th Hold time, data after elK t ns

(unless otherwise noted) .
--
»
r-
en
»
VIK
VOH
PARAMETER
Vee
Vee
Vee
Vee
Vee
=
=
=
=
=
TEST CONDITIONS
4.5 V,
4.5 V to 5.5 V, 10H
4.5 V,
4.5 V,
4.5 V,
10H
II = -18 mA
= -2 mA
= -15 mA
10H = -24 mA
10l = 32 mA
SN54AS825
SN54AS826
MIN Typt
Vee- 2
2.4
2
3.2
MAX
0.25
-1.2
0.5
SN74AS825
SN74AS826
MIN Typt
Vee- 2
2.4
2
3.2
MAX
-1.2
UNIT
2 VOL
Vee =
4.5 V, 10l = 48 rnA 0.25 0.5
V
C 10ZH Vee - 5.5 V, Vo = 2.7 V 50 50 JlA
»
en
10Zl
II
Vee
Vee
=
=
5.5 V,
5.5 V,
Vo = 0.4 V
VI = 7 V
-50 -50 JlA
mA
("') IIH, Vee = 5.5 V, VI = 2.7 V JlA

::D 10+ Vee = 5.5 V, Vo = 2.25 V -30 -1.12 -30 -112 mA
("') Outputs high
c 'AS825 Vee = 5.5 V Outputs low mA
=i Outputs disabled 58 58
en ICC
Outputs high
tAli typic"al values are at Vee = 5 V, TA = 25°e.

1283
2-540 TEXAS
INSTRUMENTS
8-BIT BUS INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
R1 = 500 O.
FROM TO
PARAMETER
(INPUT)
R2 = 500 O. UNIT
(OUTPUT)
TA = MIN to MAX
SN54AS825 SN74AS825
SN54AS826 SN74AS826
f max MHz
tPlH 7.5 7.5
ClK Any Q ns
tpHl 9.5 9.5
tpHl ClR Any Q 11 11 ns
tPZH 6 6
OC Any Q ns
tpZl 7 7
tpHZ 6 6
OC Any Q ns
tPlZ 7 7
t All typical values are at Vee = 5 V. T A = 25°C.


symbol based on the assumption of true data (0) inputs. Then outputs that produce data in phase with
the data inputs are called a
and those producing complementary data are called O. An input that causes
a
a output to go high or a Q output to go low is called Preset; an input that causes a Q output to go high
or a a
output to go low is called Clear. Bars are used over these pin names (PRE and CLR) if they are
active-low.
en
The devices on this data sheet are second-source designs and the pin-name convention used by the original !::
manufacturer has been retained. That makes it necessary to designate the inputs and outputs ofthe inverting ::>
circuit 5 and O. In some' applications it may be advantageous to redesignate the inputs and outputs as u
o and Q. In that case, outputs should be renamed as shown below. Also shown are corresponding changes a:
in the graphical symbol. Arbitrary pin numbers are shown in parentheses. u
a
Notice that and Q exchange names, which causes Preset and Clear to do likewise. Also notice that the en
polarity indicators ( r:::::... ) on PRE and CLR remain since these inputs are still active-low, but that the presence <C
or absence of the polarity indicator changes at 5, 0, and Q. Of course pin 5 (0) is still in phase with the data
input 0, but now both are considered active high. C
2
<C
ClR R PRE S (5)
en
a Q ..J
ClK C1 ClK C1 <C
0 10 (6) 0 10
Q Q
PRE s ClR R
1283
TEXAS 2-541
INSTRUMENTS
~
:t>
r-
tI)
:t>
2
C
:t>
tI)
(")
:l3
(")
c
=i
tI)
2-542
TYPES SN54ALS832. SN54AS832A. SN74ALS832. SN74AS832A
HEX 2·INPUT OR DRIVERS
D2661.DECEMBER1982-REV~EDDECEMBER1983
• High Capacitive Drive Capability SN54ALS832. SN54AS832A •.• J PACKAGE

SN74ALS832. SN74AS832A ••. N PACKAGE
• 'AlS832 Has Typical Delay Time of 5 ns (TOP VIEW)
(Cl = 50 pF) and Typical Power Dissipation of
5.3 mW per Gate
• 'AS832A Has Typical Delay Time of 3.9 ns 1A Vee
(Cl = 50 pF) and Typical Power Dissipation of 1B 6B
less than 17 mW per Gate 1Y 6A
• Package Options Include Both Plastic and Ceramic 2A 6Y
Chip Carriers in Addition to Plastic and Ceramic 2B 5B
DIPs 2Y 5A
3A 5Y
• Dependable Texas Instruments Quality and 3B 4B
Reliability 3Y 4A
GND 4Y
description
These devices contain six independent 2-input OR
drivers. They perform the Boolean functions
Y = A+B or Y = A'S in positive logic.
SN54ALS83~SN54AS832A: .. FHPACKAGE
The -1 version of the SN7 4ALS832 parts is identical SN74ALS832.SN74AS832A ... FNPACKAGE
to the standard version except that the recommend- (TOP VIEW)
ed maximum IOL is increased to 48 milliamperes. U
There is no -1 version of the SN54ALS832 parts. >-co«Uco
.... ........ >(0
The SN54ALS832 and SN54AS832A are character-
ized for operation over the full military temperature 2A 4 6A
range of - 55 De to 125 De. The SN74ALS832 and 2B 5 6Y
SN74AS832A are characterized for operation from 2Y 6 5B en
oDe to 70 De. 3A 7 5A !::
3B 8 5Y :::>
FUNCTION TABLE (each driver) 9 10 111213 u
>-o>-«co a:
INPUTS
A B
OUTPUT
Y
MZ","","","
(!) u
H X H en
X H H <t
L L L C
;2
logic symbol <t
en
..J
<t
38
4A
48
5A
58
68

~83
TEXAS 2-543
INSTRUMENTS
Supply voltage, Vee . . . . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
SN74ALS832 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00eto70 0e

UNIT
Vil low-level Input voltage 0.8 0.8 V
12 24
48t
tThe extended limit applies If Vee IS maintained between 4.75 V and 5.25 V.
electrical characteristics over recommended operating free-air temperature rango (unless otherwise noted)
MIN TYP: MAX MIN TYP: MAX
=
_II
VIK Vee = 4.5 V, II -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vce- 2 Vee- 2
Vee = 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
»
r
VOH
Vee = 4.5 V,
Vee = 4.5 V, IOH
IOH = -12 mA
= -15 mA
2
2
V
(J) Vee = 4.5 V, IOl = 12 mA 0.25 0.4 0.25 0.4
»2 VOL Vee = 4.5 V, IOl

= 24 mA
0.35 0.5
V
C II Vee = 5.5 V, VI =7 V 0.1 0.1 mA

= 2.7 V
»
(J)
IIH
III
Vee = 5.5 V,
Vee = 5.5 V,
VI
VI = 0.4 V
20
-0.1
20
-0.1
Il A
mA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
(") leeH Vee = 5.5 V, VI = 4.5 V 4 8 4 8 mA
leel Vee = 5.5 V, VI = 0 V 9.5 16 9.5 16 mA
::JJ
(") tAli tYPical values are at Vee = 5 V, T A = 25 DC.
C
(J)
VCC = 4.5 V to 5.5 V,
Cl = 50 pF.
FROM TO Rl = 500 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tplH 2 10 2 8
A or B Y ns
tpHl 2 10 2 8
1283
2-544 TEXAS
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS832A .. .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 1-25 °e
SN74AS832A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 150 °e

SN54AS832A .SN74AS832A
UNIT
TA Operating free-air temperature ":"55 125 0 70 °e
-18 mA -1.2 -1.2 V
Vee = 4.5 V, IOH = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, 10H = -40 mA 2
Vee = 4.5 V, 10H = -48 mA 2
Vee = 4.5 V, 10L = 40 mA 0.25 0.5
VOL V
Vee = 4.5 V, 10L = 48 mA 0.35 0.5
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 ",A
IlL Vee = 5.5 V, VI = 0.4 V -0.5 -0.5 mA
10* Vee = 5.5 V, Va = 2.25 V -135 -135 mA
leeH Vee = 5.5 V, VI = 4.5 V 9 15 9 15 mA
leeL Vee = 5.5 V, VI = 0 V 22 36 22 36 mA

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q.
PARAMETER UNIT
, SN54AS832A SN74AS832A
MIN MAX MIN MAX
tpLH 1 7 1 5.5
A or 8 Y ns
tpHL 1 6.5 1 5.5
283
TEXAS 2-545
INSTRUMENTS
- l>
r-
en
l>
:2
C
l>
en
Q
:D
n
c
=i
en
2-546
SN74ALS841, SN74AS841, SN74ALS842, SN74AS842
10·BIT BUS INTERFACE D·TYPE LATCHES WITH 3·STATE OUTPUTS
• 3·State Buffer· Type Outputs Drive Bus-Lines SN54ALS841. SN54AS841 •.• JT PACKAGE
SN74ALS841.SN74AS841 .• : NT PACKAGE
Directly
(TOP VIEW)
• Bus-Structured Pinout oc VCC
10 10
• Provide Extra Bus Driving Latches 20
Necessary for Wider AddresslData Paths or 30
Buses with Parity 40 40
50
• Buffered Control Inputs to Reduce DC
Loading 80
90 10 15 90
• Power-Up High-Impedance State 100 " 14 100
GNO 12 13 C
Ceramic Chip Carriers in Addition to Plastic SN54ALS841. SN54AS841 ••. FH PACKAGE
and Ceramic DIPs SN74ALS841. SN74AS841 ..• FN PACKAGE
(TOP VIEW)
• Dependable Texas Instruments Quality and u
Reliability ~ elg ~ ~~ ~
description 3D 30
40 40
These 1O-bit latches feature three-state outputs 50 50
NC
designed specifically for driving highly capacitive
or relatively low-impedance loads. They are 70
particularly suitable for implementing buffer 80
registers, 1/0 ports, bidirectional bus drivers, and

ooouuaa
working registers. OlOZZ
~l!l
00l
~
The ten latches are transparent D-type. The SN54ALS842. SN54AS842 ••• JT PACKAGE
'ALS841 and' AS841 have noninverting data (0) SN74ALS842. SN74AS842 .•• NT PACKAGE
CJ)
inputs. The' ALS842 and' AS842 have inverting (TOP VIEW)
[) inputs. VCC
!:::
10
::)
A buffered output control (OC) input can be used 20 CJ
to place the ten outputs in either a normal logic 30 a:
state (high or low levels) or a high-impedance (3
state. In the high-impedance state, the outputs
75 70
CJ)
neither load nor drive the bus lines significantly.
The high-impedance state and increased drive
80 80 <C
9'0 90
provide the capability to drive the bus lines in a 100 C
bus-organized system without need for interface GNO Z
or pull-up components. SN54ALS842. SN54AS842 ••• FH PACKAGE <C
The output control does not affect the internal, SN74ALS842. SN74AS842 ... FN PACKAGE CJ)
(TOP VIEW) ...J
operation of the latches. Old data can be retained
or new data can be entered while the outputs
<C
are'off. 4 3 2 1 282726
35 5 25 30
The SN54ALS841, SN54AS841, SN54ALS842, 45 6 24 40
and SN54AS842 are characterized for operation 55 7 23 50
22 NC
over the full military temperature range of NC
65 21 60
-55°C to 125°C. The SN74ALS841, 70 10 20 70
SN74AS841,SN74ALS842,andSN74AS842 85 11 19 80
12131415161718
are characterized for operation from OOC to
70°C. l§llg ~ ~ U g g
~l!l ~

ThIs document contain. infOrmation on 8 product under
development, Texa.lnatrument. re.erve. the right to TEXAS 2-547
10·BIT BUS INTERFACE O·TYPE LATCHES WITH 3·STATE OUTPUTS
FUNCTION TABLES
•ALS841 •• AS841 •ALS842 •• AS842

OC C D Q OC C D Q
L H H H L H H L
L H L L L H L H
L ' L X ao L L X ao
H X X Z H X X Z
, ALS841 , , AS841 logic symbol , ALS841, , AS841 logic diagram (positive logic)
oc
C
1D (23)
(2) 10
2D 10
3D
4D (22)
(3) 2a
5D 20
60
70
(21) 30
80 (4)
3D
90
(11)
100
(20)
IIfJ 40
(5) 40
l> (6)
(19)
50
r- 50
en
l> (7)
(18)
60
:2 60
C
l> (8)
(17)
70
en 70
(")
(16)
::D 80
(9) 80
(")
C (15) 90
~ 90
(10)
en
(14)
(11) 100
100
1283
2-548 TEXAS
INSTRUMENTS
, ALS842. ' AS842 logic symbol , ALS842, , AS842 logic diagram (positive logic)
oc
C
10 (23) 10
(23)
(22) (2) 10
20 10
3D
40 40
(22)
50 50 (3) 20
20
60 60
70 70
(21)
80 80 (4) 30
30
90 90
100 100
(20)
(5) 40
40
(19)
(6) 50
50
(18)
(7) 60
60
(17)
(8) 70
70
(9)
(16)
80 en
80
!::
(15)
::>
(10) 90 c.J
9'0
a:
(14) c.J
100
(11) 100
en
«
c
z
absolute maximum. ratings over operating free-air temperature range (unless otherwise noted) «
Supply voltage, Vee ........................................................ , 7 V
en
...J
Input voltage .............................................................. 7 V
Voltage applied to a disabled 3-state output ..................................... , 5.5 V
«
Operating free-air temperature range:
SN54ALS841, SN54AS841, SN54ALS842, SN54AS842 ........... -55°eto 125°e
, SN74ALS841, SB74AS841, SB74ALS842, SN74AS842 ......... " .... ooe to 70°C
1283
TEXAS 2-549
INSTRUMENTS
SN74ALS841, SN74ALS842

SN54ALS84t SN74ALS841

I 'ALS841 ns
tw
1'ALS842
tsu Setup time, data before enable e.j. ns
Hold time, data after enable e.j.

I 'ALS841 ns
th
I 'ALS842

..
VIK Vee = 4.5V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10l = 12 mA 0.25 0.4 0.25 0.4
VOL V
:t>
r- 10ZH
Vee = 4.5 V,
Vee = 5.5 V,
10l = 24 mA
Vo = 2.7 V 20
0.35 0.5
20 Il A
en 10Zl Vee = 5.5 V, Vo = 0.4 V -20 -20 Il A
Vee = 5.5 V, V, = 7 V 0.1 0.1 mA
:t> 'I
I'H Vee = 5.5 V, VI = 2.7 V 20 20 IlA
2 Vee'= 5.5 V, VI = 0.4 V -0.1 -0.1 mA
',L
C 10+ Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA
:t> Outputs high
en 'AlS841 Outputs low
(") Outputs disabled 25 25
ICC Vee = 5.5 V mA
Outputs high
:lJ 'AlS842 Outputs low
(")
c Outputs disabled 28 28
::t
en
1283
2-550 TEXAS
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 fl.
FROM TO
PARAMETER R2 = 500 fl. UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
tpLH 7 7
D Q ns
tpHL 9 9
tpLH
C Q ns
tpHL
tpZH
OC Q ns
tpZL
tpHZ
OC Q ns
t,pLZ
, ALS842 s'!Vitching characteristics (see Note 1)

Vce = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 fl.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
tpLH 11 11
is Q ns
CJ)
tpHL 9 9
tPLH
C Q ns !::
tpHL ::>
tpZH
6C u
tpZL
Q ns
a:
tpHZ
tpLZ
OC Q ns u
CJ)
t All typical values are at T A = 25°C.
<t
o
z
<t
CJ)
-I
<t
1283
TEXAS 2-551
INSTRUMENTS
TYPES SN54AS841; SN54AS842
SN74AS841, SN74AS842
10-BIT BUS INTERFACE OoTYPE LATCHES WITH 3-STATE OUTPUTS

SN54AS841 SN74AS841
tw Pulse duration, enable e high ns
tsu Setup time, data before enable e~ ns
th Hold time, data after enable e~ ns

SN54AS841 SN74AS841
V,K Vee = 4.5 V, " = -18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -.15 rnA 2.4 3.2 2.4 3.2 V
Vee = 4.5 V, 10H = -24 rnA 2 2
Vee = 4.5 V, 10l = 32 rnA 0.25 0.5
IIfJ VOL
10ZH
10Zl
Vee
Vee
Vee
= 4.5
=
=
V,
5.5 V,
5.5 V,
10l = 48 rnA
Vo = 2.7 V
Vo = 0.4 V
50
-50
0.25 0.5
50
-50
V
/lA
/lA
:t:- = 5.5
r- I, Vee V, V, = 7 V rnA
en IIH Vee = 5.5 V, V, = 2.7 V /lA
:t:- ',L Vee = 5.5V, V, = 0.4 V rnA

10=1: Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
2: Outputs high 36 36
C 'AS841 Outputs low 58 58
:t:- , Outputs disabled I
56 56
en lee Vee = 5.5 V rnA
Outputs high 38 38
n 'AS842 Outputs low

Outputs disabled
60
58
60
58
::D
n tAli typical values are at vee;' 5 V, TA = 25°C.
c: tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
~ Additional information on these products can be obtained from the factory as it becomes available.
en
1283
2-552 TEXAS
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 fl.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS841 SN74AS841
tpLH 4 4
D Q ns
tpHL 4.5 4.5
tpLH
C Q ns
tpHL
tpZH 6 6
OC Q ns
tpZL 6 6
tpHZ 4 4
OC Q ns
tpLZ 5 5

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 fl.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS842 SN74AS842
tPLH 4 4.
IT Q ns
4.5 4.5
tpHL
tpLH
en
tpHL
C Q ns !::
::::>
tpZH
OC Q
6 6
ns u
tpZL 6
4
6
4
a::
tPHZ
tPLZ
OC Q
5 5
ns u
en
NOTE1: For load circuits and voltage waveforms. see page 1-12. «
Additional information on these products can be obtained from the factory as it becomes available. c
;2
«
en
..J
«
1283
TEXAS 2-553
INSTRUMENTS
IIIfJ
:t>
r-
en
:t>
:2
o
:t>
en
(")
:JJ
(")
C
~
en
2-554
9·BIT BUS INTERFACE O·TYPE LATCHES WITH 3·STATE DECEMBER
OUTPUTS 1983
• 3·State Buffer· Type Outputs Drive Bus·Lines SN54ALS843. SN54AS843 ... JT PACKAGE
Directly SN74ALS843. SN74AS843 ... NT PACKAGE
(TOP VIEW)
Q Bus-Structured Pinout
Dc 24 VCC
10 23 1Q
• Provide Extra Bus Driving Latches 20 3 22 2Q
Necessary for Wider Address/Data Paths or 3D 4 21 3Q
Buses with Parity 40 5 20 4Q
50 6 19 5Q
• Buffered Control Inputs to. Reduce DC 60 18 60
70 17 7Q
Loading 80 8Q
16
90 10 15 9Q
• Power-Up High Impedance CLR 11 14 PRE
GNO 12 13 C
Ceramic Chip Carriers in Addition to SN54ALS843. SN54AS843 •.. FH PACKAGE
Plastic and Ceramic DIPs SN74ALS843. SN74AS843 .•. FN PACKAGE
(TOP VIEW)
• Dependable Texas Instruments Quality u
and Reliability ~ ~Ig ~;;'~ ~
4 3 2 1 282726
3Q
description 40
5Q
These 9-bit latches feature three-state outputs
NC
,.
designed specifically for driving highly capacitive 6Q
or relatively low-impedance loads. They are 70
8Q
particularly suitable for implementing buffer
1213'1415161718
working registers.
The nine latches are transparent D-type. The· SN54ALS844. SN54AS844 ... JT PACKAGE
'ALS843 and' AS843 have noninverting data (D)
inputs. The' ALS844 and' AS844 have inverting
SN74ALS844. SN74AS844 ... NT PACKAGE
(TOP VIEW)
en
5 inputs. !::
:J
A buffered output control (OC) input can be used U
to place the ten outputs in either a normal logic 35
4Q
a:
state (high or low levels) or a high-impedance 5Q U
state. In the high-impedance state, the outputs 6Q
en
«
neither load nor drive the bus lines significantly. 75
85 8Q
The high-impedance state and increased drive 95 10 9Q
provide the capability to drive the bus lines in a CLR 11
15
14 PRE c
bus-organized system without need for interface GNO 12 13 C
2
or pull-up components. SN54ALS844. SN54AS844 ... FH PACKAGE «
The output control (OC) does not affect the
SN74ALS844. SN74AS844 .•. FN PACKAGE
(TOP VIEW)
en
..J
internal operation of the latches. Old data can
be retained or new data can be entered while the
u
1~1~lg ~ ;;'~ ~ «
outputs are off.
30
The SN54ALS843, SN54AS843, SN54ALS844, 4Q
and SN54AS844 are characterized for operation 5Q
NC
over the full military temperature range of
65
- 55°C to 125°C. The SN74ALS843, 7Q
SN74AS84~ SN74ALS84~ andSN74AS844 8G
are characterized for operation from OOC to
70°C.

Thia ~t contlllnsinfonnation on • product under
development. Tex •• Instruments re.erves the right to TEXAS 2-555
FUNCTION TABLES
•ALS843 •• AS843 •ALS844 •• AS844

PRE CLR OC C 0 Q PRE CLR OC C 0 Q
L H L X X H L H L X X H
H L L X X L H L L X X L
L L L X X H L L L X X H
H H L H L L H H L H L H
H H L H H H H H L H H L
H H L L X 00 H H L L X QO
X X H X X Z X X H X X Z
logic symbol , ALS843, , AS843 logic diagram (positive logic)
oc ~(1.:.....)- - - d ~_ _ _ _ _.....,
oc
CLR
PRE
c
(23)
10 10
(3) (22)
20 20 10.:.:(2::....)_ _-++-1
(4) (21)
3D 30
(5) (20)
40 40
(6) (19)
116 50
60
70
(7)
(S)
(9)
(1S)
(17)
(16)
50
60
70
so
20 .:..::;(3.:.....)_ _+-I-~
l> ·SO
(10) (15)
r- 90 90
3D .:..:(4::....)_ _+++-1
(f)
l>
2:
40 :.:(5::....)_ _+++-1
C
l>
en
50,;.:(6::....)----1--+-+-1
r2
:2:J
(")
c: 60.:.:,(7.:.-)----1--+-+-1
=i
en
70'::(S::",,)--++-+-l
SO .::(9::....)----1--+-+-1
90 (10)

This symbol is in accordance with IEEE Std 9 and recent decisions of IEEE.
1283
2·556 TEXAS
INSTRUMENTS
POST OFFICE SOX 225012 • DALLAS. TEXAS 75265
, SN74ALS843, SN74AS843, SN74ALS844, SN74AS844
logic symbol .• ALS844•• AS844 logic diagram (positive logic)
'6C
PRE
ctR
C
10 10
20 20
10 (2) (23)10
35 30
45
55
60 20 (3) (22)20
75
85
95
(4 (21)30
30. )
40 (5) (20)40
50 (6)
60 (7)
(19) 50
(18)60
..
(IJ
!::
:)
70 (8) (17) 70
CJ
a::
CJ
80 (9) (16)80
(IJ
«
c
90 (10) (15)90
Z
«
(IJ
-I
This symbol is in accordance with IEEE Std 9 and recent decisions of IEEE. «
Input voltage ........................................................ ,..... 7 V
Voltage applied to a disabled 3-state output ................................. , . . .. 5.5 V
SN54ALS843, SN54AS843, SN54ALS844, SN54AS844 ....................... -55°e.
SN74ALS843, SN74AS843, SN74ALS844, SN74AS844 . . . . . . . . . . . . . . . .. -oDe to 70 0 e
1283
TEXAS 2-557
INSTRUMENTS
9·BI1 BUS INTERFACE D·TYPE LATCHES WITH 3·STATE OUTPUTS

Vee Supply voltage 4.5 5 55 4.5 5 5.5 V

I 'ALS843
tw ns
I 'ALS844
tsu Setup time, data before enable e,J, ns
Hold time, data after enable e,J,

I 'ALS843 ns
th
I 'ALS844

(unless otHerwise noted)
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 to 5.5 V, 10H = -0.4 mA VCC- 2 VCC- 2
~
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
»
r-
VOL
Vee = 4.5 V,
Vee = 4.5 V,
IOL = 12 mA
10L = 24 mA
0.25 0.4 0.25
0.35
0.4
0.5
V
CJ) 10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 p,A
»
2
10ZL
II
Vee = 5.5 V,
Vee = 5.5 V,
Va =
VI = 7 V
0.4 V -20
0.1
-20
0.1
p,A
mA
C IIH Vee = 5.5 V, VI = 2.7 V 20 20 p,A
l> IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
CJ) 10:1: Vee = 5.5 V, Va = 2.25 V -15 -70 -15 -70 mA
(") Outputs high
'ALS843 Outputs low
:xl
(") Vee = 5.5 V
mA
c lee
Outputs high
=i
CJ)
'ALS844 Outputs low
t All typical values are at VCC = 5 V, T A = 25 cC.

tThe output conditions have been chosen to produce a current that closely approximates one half of 1he true short-circuit output current, lOS.
1283
2-558 TEXAS
INSTRUMENTS
I ALS843 switching characteristics (see Note 1)
Vcc = 4.5 V to 5.5 V.
CL =·50 pF.
FROM TO
R1 = 500 n.
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
tPLH 7 7
0 Q ns
tpHL 9 9
tpLH
C Q ns
tpHL
tPLH PRE Q ns
tpHL CLR Q ns
tpZH
OC 0 ns
tpZL
tpHZ
OC 0 ns
tPLZ
I ALS844 switching characteristics (see Note 1)

VCC = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
PARAMETER
FROM TO
R2 = 500 n. UNIT
CI'J
(INPUT) (OUTPUT)
TA = MIN to MAX !::
SN54ALS844 SN74ALS844 :l
(.)
MIN .Typt Typt
tpLH
MAX
7
MIN
7
MAX
a:
[) Q ns
tpHL 9 9 (.)
tPLH CI'J
tpHL
C Q ns
«
tPLH PRE
CLR
Q
Q
ns
o
tpHL ns 2
tpZH
tpZL
OC 0 ns «
tpHZ
CI'J
OC 0 -J
tPLZ
ns
«
NOTE 1: For load circuit and,voltage waveforms, see page 1-12.
1283
TEXAS 2-559
INSTRUMENTS
POST OFFICE BOX 225012 • DAl.LAS. TEXAS 75265

SN54AS843 SN74AS843
Vee Supply voltage 4.5 5 55 4.5 5 5.5 V
Vll low-level input voltage 0.8 0.8 V
tw Pulse duration, enable e high I elR or PRE low ns

I e high
tsu Setup time, data before enable e + ns
th Hold time, data after enable e + ns

SN54AS843 SN74AS843
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V, IOH = -2 mA vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -15 mA 2.4 3.2 2.4 3.2 V
Vee = 4.5 V, IOH = -24 mA 2 2
Vee = 4.5 V, IOl = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, IOl = 48 mA 0.25 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
IOZl Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
IIH Vee = 5.5 V, VI=2.7V p.A
loi Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Outputs high 38 38
'AS843 Outputs low 57 57
lee Vee = 5.5 V mA
Outputs high 39 39
'AS844 Outputs low 58 58

tThe output conditions have been chosen to produce a current tha! closely approximates one half of the true short-circuit output current, lOS'
1283
2-560 TEXAS
INSTRUMENTS
9·81T BUS INTERFACE O·TYPE LATCHES WITH 3·STATE OUTPUTS
I AS843 switching chaacteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 fl.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS843 SN74AS843
tpLH 4 4
D Q ns
tpHL 4.5 4.5
tpLH
C 0 ns
tpHL
tpLH PRE Q 5 5 ns
tpHL CLR Q 5.5 5.5 ns
tpZH 6 6
OC 0 ns
tpZL 6 6
tpHZ 4 4
OC 0 ns
tpLZ 5 5

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 fl.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN TVPt. MAX MIN TVpt MAX !::
tpLH [)
4 4 :::J
Q ns
tpHL 4.5 4.5 CJ
tpLH
a:
C Q ns
tpHL CJ
tpLH PRE Q 5 5 ns en
tpHL CLR Q 5.5 5.5 ns «
tpZH
tpZL
OC Q
6
6
6
6
ns o
2
tpHZ
tpLZ
OC Q
4
5
4
5
ns «
en
t All typical values are at TA = 25 ce. ...J
NOTE1: For load circuit and voltage waveforms. see page 1-12. «
1283
TEXAS 2-561
INSTRUMENTS
9·BIT BUS INTERFACE D·TVPE LATCHES WITH 3·STATE OUTPUTS
symbol based on the assumption of true data (0) inputs. Then outputs that produce data in phase with
the data inputs are called a:
and those producing complementary data are called O. An input that causes
a 0 output to go high or a 0 output to go low is called Preset; an input that causes a Q output to go high
or a 0 output to go low is called Clear. Bars are used over these pin names (PRE and CLR) if they are
active-low.
The devices on this data sheet are second-source designs and the pin-name convention used by the original
circuit 0 and O. In some applications it may be advantageous to redesignate the inputs and outputs as
o and O. In that case, outputs sholJld be renamed as shown below. Also shown are corresponding changes
Notice that 0 and 0: exchange names, which causes Preset and Clear to do likewise. Also notice that the
polarity indicators (t:::::::::...) on PRE and CLR remain since these inputs are still active-low, but that the presence
or absence of the polarity changes at 5,0, and Q. Of course pin 5 (0) is still in phase with the data input
0, but now both are considered active high.
s m R
(5) Q
a
-
CLK ";"""'--I>Cl CLK C1
o 10 D 10 (6)
Q
CIA R PRE S
»
r-
en
»
2
C
l>
en
("')
:JJ
("')
c
=i
en
1283
2-562 TEXAS
INSTRUMENTS
SN74ALS845, SN74AS84~ SN74ALS84t SN14AS846
02825. DECEM8ER 1983
o 3·State Buffer·Type Outputs Drive Bus·Lines SN54ALS845, SN54AS845 •.. JT PACKAGE

Directly SN74ALS845, SN74AS845 ..• NT PACKAGE
(TOP VIEW)
• Provides Extra Bus Driving Latches
Necessary for Wider Address/Data Paths or
Buses with Parity
• Buffered Control Inputs to Reduce DC
Loading
o Power-Up High-Impedance State CLR 11 14 PRE
GND 12 13 C
Ceramic Chip Carriers in Addition to Plastic SN54ALS845, SN54AS845 ... FH PACKAGE
and Ceramic DIPs SN74ALS845, SN74AS845 ... FN PACKAGE
(TOP VIEW)
R,eliability
4 3 2 1 28 2726
20 5 25 2Q
description 3D 6 24 3Q
40 7 23 4Q
These 8-bit latches feature three-state outputs NC 22 NC
designed specifically for driving highly capacitive 50 21 5Q
60 10 20 6Q
70 11 19 7Q
particularly suitable for implementing buffer
working registers.
The eight latches are transparent D-type. The SN54ALS846, SN54AS846 ... JT PACKAGE
'ALS845 and' AS845 have noninverting data (D) SN74ALS846, SN74AS846 ... NT PACKAGE
inputs. The' ALS846 and' AS846 have inverting (TOP VIEW)
5 inputs. Since CLR and PRE are independent of VCC
Dc3
the clock, taking the CLR input low will cause lQ
the eight Q outputs to go low. Taking the PRE
input low will cause the eight Q outputs to go 3Q
4Q
high. When both PRE and CLR are taken low, the 5Q
outputs will follow the preset condition.
75 7Q
A buffered output control (OC) input can be used 8D 10 15 8Q
to place the eight outputs in either a normal ill 11 14 PRE
GND 12 13 C
logic state (high or low levels) or a high-
impedance state. In the high-impedance state, SN54ALS846, SN54AS846 ... FH PACKAGE
the outputs neither load nor drive the bus lines SN74ALS846, SN74AS846 ... FN PACKAGE
significantly. The high-impedance state and (TOP VIEW)
increased drive provide the capability to drive
the bus lines in a bus-organized system without
need for interface or pull-up components.

ThIs document contain. Inlonnatkln on a product under
TYPES SN54ALSB45, SN54ASB45, SN54ALSB46, SN54ASB46
SN74ALSB45, SN74ASB45, SN74ALS846, SN74AS846
The output controls (OC1, OC2, OC3) do not affect the internal operation of the latches. Old data can
be retained or new data can be entered while the outputs are in the high-impedance state. '
The SN54ALS845, SN54AS845, SN54ALS846, and SN54AS846 are characterized for operation over
the full military temperature range of - 55°C to 125°C. The SN74ALS845, SN74AS845, SN74ALS846,
and SN74AS846 are characterized for operation from OOC to 70°C.
FUNCTION TABLES
•ALSB45 •• ASB45 •ALSB46 •• ASB46

PRE CLR OC1 OC2 OC3 C 0 a PRE CLR OC1 OC2 OC3 C 0 a
L H L L L X X H L H L L L X X H
H L L L L X X L H L L L L X X L
L L L L L X X H L L L L L X X H
H H L L L H L L H H L L L H L H
H H L L L H H H H H L L L H H L
H H L L L L X 00 H H L L L L X 00
X X L L H X X Z X X L L H X X Z
x X L H L X X Z x X L H L X X Z
x X L H H X X Z x X L H H X X Z
x X H L L X X Z x X H L L X X Z
x X H L H X X Z x X H L H X X Z
x X H H L X X Z x X H H L X X Z
x X H H H X X Z x X H H H X X Z
-.J logic symbols

•ALS845. 'ASB45 •ALS846 •• AS846

These symbols are in accordance with IEEE Std 9 and recent decisions of IEEE.
1283
2-564 TEXAS
INSTRUMENTS
POST OFFICE SOX 225012 • DALLAS. TEXAS 75265
, ALS845, , AS845 , ALS846, , AS846
-(1) OC1-;-=(1.)_____---,
OCl7:::(27-)- - - - - - ,
- (2)
OC2 (23) OC2-(-3)----------~
OC3---------' OC3 _2-'--_ _ _- J
i>RE (14) PRE (14)
(3) (22) lQ liS (3) (22) lQ

10
(4) (21) 2Q 20 (4) (21) 2Q

20
(5) (20) 3Q 3D (5) (20) 3Q

3D
(6) (19) 4Q 40 (6) (19) 4Q

40
50
(7) (18) 5Q 50 (7) (18) 5Q
OIl
CJ)
t::
::J
60
(8) (17)6Q 60 (8) (17)
6Q U
IX:
U
CJ)
70 (9) (16)7Q 70 (9) (16) 7Q
<t
C
(10)
2
80
(15) 8Q 80 (10) (15)
8Q <t
CJ)
~
<t
Input voltage ............................,.................................. 7 V
SN54ALS845, SN54AS845, SN54ALS846, SN54AS846 ................. -55°C to 125°C
SN74ALS845, SN74AS845, SN74ALS846, SN74AS846 ................. -OOeto 70 0 e
1283
TEXAS 2-565
INSTRUMENTS
POST OFFICE BOX 225012 • OALLAS. TeXAS 75265

SN54ALS846 SN?4ALS846 UNIT
V,H High-level Input voltage 2 2 V
tw Pulse duration
I CLR or PRE low ns
I C high
tsu Setup time, data before enable e.j. ns
Hold time, data after enable e.j.

I 'ALS845 ns
th
I 'ALS846
TA Operating free-air temperature -~5 125 0 70 °e

V,K Vee = 4.5 V, " = -18 mA -1.5 -1.5 V
-
Vee - 4.5 V to 5.5 V, IOH - -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee - 4.5 V, IOH - -2.6 mA 2.4 3.2
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 24 mA 0.35 0.5
l> IOZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A·
r-
CI'I IOZL Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
Vee - 5.5 V, V, - 7 V 0.1 0.1 mA
l> "
IIH Vee = 5.5 V, V, = 2.7 V 20 20 p.A
:2 "L Vee = 5.5 V, V, = 0.4 V -0.1 -0.1 mA
C lo~ Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA
l> Outputs high
(I) 'ALS845 Outputs low
(") ICC Vee = 5.5 V mA
Outputs high
:ii 'ALS846 Outputs low
(")
c
::::t t All typical values are at Vee = 5 V,
T A = 25°e. .
tn *The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
1283
2-566 TEXAS
INSTRUMENTS
TYPES SN54ALS845. SN5~ALS846
SN74ALS845. SN74ALS846
8-BIT BUS INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO
R1 = 500 n.
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
tpLH 7 7
D Q ns
tpHL 9 9
tpLH
C Q ns
tpHL
tpLH PRE Q ns
tpHL CLR Q ns
tpZH
DC Q ns
tpZL
tpHZ
DC Q ns
tpLZ

Vee = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TD
R1 = 500 n.
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
SN54ALS846 ,sN74ALS846
MIN Typt MAX MIN Typt MAX C/)
tpLH
tpHL
IT Q
7
9
7
9
ns !::
::l
tpLH
C Q ns (J
tpHL a:
tpLH PRE Q ns
(.)
tpHL CLR Q ns
tpZH CJ)
DC Q ns
tpZL <C
tpHZ
DC Q ns C
tpLZ 2!
t All typical values are at TA = 25 cc. <C
en
-I
<C
1283
TEXAS 2-567
INSTRUMENTS
TYPES SN54ASB45, SN54ASB46
SN74ASB45, SN74ASB46
B·BIT BUS INTERFACE O·TYPE LATCHES WITH 3·STATE OUTPUTS
SN54AS845 SN74AS845
tw Pulse duration
I ern or PRE low ns
I e high
tsu Setup time, data before enable e~ ns
th Hold time, data after enable e~ ns
TA Operating free-air temperature -55 125 0 I 70 °e

SN54AS845 SN74AS845
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
-
Vee = 4.5 to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -15 rnA 2.4 3.2 2.4 3.2 V
Vee = 4.5 V, 10H = -24 rnA 2 2
Vee = 4.5 V, 10l = 32 rnA 0.25 0.5
VOL V
Vee = 4.5 V, 10l = 48 rnA 0.25 0.5
l> 10ZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
r- = Vo = 0.4 V
en 10Zl
II
Vee
Vee
5.5 V,
= 5.5 V, VI - 7 V
-50 -50 p.A
rnA
l> IIH Vee = 5.5 V, VI = 2.7 V p.A
z I,l Vee = 5.5 V, V,= 0.4 V rnA
c 10+ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
»
en 'AS845
Outputs high
Outputs low
35
52
35
52
(") ICC Vee = 5.5 V
Outputs high 36
rnA
36
$ 'AS846 Outputs low 53 53
(') Outputs disabled 53 53
c tAli typical values are at Vee = 5 V, TA ='25°e.
=i tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
en
Additional information on these products can be obtained from the factory as It becomes available.
1283
2-568 TEXAS
INSTRUMENTS
8·BIT BUS INTERFACE D·TVPE LATCHES WITH 3·STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 O.
FROM TO
PARAMETER R2 = 500 O. UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS845 SN74AS845
tpLH 4 4
0 Q ns
tpHL 4.5 4.5
tpLH Q
C ns
tpHL
tpLH PRE Q 5 5 ns
tpHL CLR Q 5.5 5.5 ns
tpZH 6 6
OC Q ns
tpZL 6 6
tp'HZ 4 4
OC Q ns
tpLZ 5 5

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
SN54AS846 SN74AS846
MIN Typt MAX MIN Typt MAX CJ)
tpLH
0 Q
4 4
ns t:::
tpHL 4.5 4.5 ::>
tpLH CJ
-a:
C Q ns
tpHL
tpLH PRE Q 5 5 ns ( .)
tpHL C[R Q 5.5 5.5 ns
6 6 CJ)
tpZH
tpZL
OC Q
- 6 6
ns <C
tpHZ
OC Q
4 4
ns C
tpLZ 5 5 2
t All typical values are at T A = 25 cc. <C
NOTE 1: For load circuit and voltage waveforms. see page 1·12. CJ)
..oJ
<C
1283
TEXAS 2-569
INSTRUMENlS
o flip·flop signal conventions
It is normal TI practice to name the outputs and other inputs of a D-type latch and to draw its logic
symbol based on the assumption of true data (D) inputs. Then outputs that produce data in phase with
the data inputs are called aand those producing complementary data are called Q. An input that causes
a
a output to go high or a Q output to go low is called Preset; an input that causes a 0: output to go high
or a a output to go low is called Clear. Bars are used over these pin names (PRE and CLR) if they are
active-low.
The devices on this data sheet are second-source designs and the pin name convention used by the original
circuit 0 and O. In some applications it may be advantageous to redesignate the inputs and outputs as
D and Q. In that case, outputs should be renamed as shown below. Also shown are corresponding changes
a
Notice that and Q exchange names, which causes Preset and Clear to do likewise. Also notice that the
polarity indicators (~) on PRE and CLR remain since these inputs are still active-low, but that the presence
or absence of the polarity indicator changes at 5, a, and O. Of course pin 5 (a) is still in phase with the data
input D, but now both are considered active high.
R PfiE s (5)
Q
CLK CLK C1
o 10 D 10
(6) Q
a
s CIR R
16
1>
r-
en
1>
2
C
1>
en
o
:xJ
o
c::
=i
en
&&
1283
2-570 TEXAS
.INSTRUMENTS
DECEMBER 1983
• 4-Line to 1-Line Data Selectors/Multiplexers SN54AS850. SN54AS851 .•. JD PACKAGE

That Can Select 1 of 16 Data Inputs. SN74AS850. SN74AS851 ... N PACKAGE
Typical Applications: (TOP VIEW) -
Boolean Function Generators 07 Vee

Parallel-to-Serial Converters 06 08
Data Source Selectors 05 09
04 010
• Cascadable to n-Bits 03 011
• 3-State Bus Driver Outputs 02 012
01 013
• 'AS850 Offers Clocked Selects; 'AS851 DO 014
Offers Enable-Controlled Selects GY 015
• Has a Master Output Control (G) for G Y
Cascading and Individual Output Controls GW 50
(GY, GW) for Each Output eLK/5e* 51
W 52
• Package Options Include both Plastic and GNO 53
Ceramic Carriers in Addition to Plastic and
Ceramic DIPs
SN54AS850. SN54AS851 ... FH PACKAGE·
• Dependable Texas Instruments Quality and SN74AS850. SN74AS851 ... FN PACKAGE
Reliability (TOP VIEW)
U
description q-LOCOr-- Uoom
0000>00
These four-line to one-line data 432 1
selectors/multiplexers provide full binary 010
decoding to select one-of-sixteen data sources 011
with complementary Y and W outputs. The 01 012 CJ)
'AS850 has a clock-controlled select register
allowing for a symmetrical presentation of the
DO 013 !:::
GY 014 ::l
select inputs to the decoder while the' AS851 G 015 CJ
has an enable-controlled select register allowing
the user to select and hold one particular data
GW Y a:
12 131415161718
line. CJ
CJ)
A buffered group of output controls (3, GY, GW)
can be used to place the two outputs in either
«
a normal logic (high or low logic level) or a high- c
z
impedance state. In the high-impedance state
the outputs neither load nor drive the bus lines
'elK for 'AS850 or ~ for 'AS851
«
significantly. The high-impedance state and CJ)
increased drive provide the capability to drive the ...J
bus lines in a bus-organized system without the «
need for interface or pull-up components.
The output controls do not affect the internal operations of the data selector/multiplexer. New data can
be up while the outputs are in the high-impedance state.
from -55°e to 125°e. The SN74AS850 and SN74AS851 are characterized for operation from oDe to
70°C.

1283
ThIs document contains information on 8 product under
development. Texaslnltrumentl reserves the right to TEXAS 2-571
change or discontinue this product without notice. INSJRUMENlS
POST OFFICE BOX 225012 • DAllAS, TEXAS 75265
INPUT SELECTION TABLE OUTPUT FUNCTION TABLE
SELECT INPUTS 'AS850 'AS851 INPUT OUTPUTS

G GY GW
S3 S2 S1 SO CLK SC SELECTED Y W
L L L L t L DO H X X Z Z
L L L H t L 01 L H L Z Z
L L H L t L 02 L L L 0 Z
L L H H t L 03 L H H Z 0
L H L L t L 04 L L H 0 IT
L H L H t L 05
o = level of selected input 00-015
L H H L t L 06
L H H H t L 07
H L L L t L 08
H L L H t L 09
H L H L t L 010
H L H H t L 011
H H L L t L 012
H H L H t L 013
H H H L t L 014
H H H H t L 015
X X X X H or L H On
On = the input selected before the most-recent low-to-high transition of ClK

or SC.
logic symbols
If) 'AS850 'AS851
MUX MUX
l> G20
r- 20EN21
C/)
20EN22 20EN22
l> C23
z C23
C 2300} °
G-
23D"} 0 G-
l> 15 15
en 2303 2303
o
-
('") °
1 21 "V
(19) y
:J:J 2
('")
c: 4
(13) w
=t 5 22 "V
en 6
7
8
9
10
11
12
013 013 13
014 014 14
015 015 15
1283
2-572 TEXAS
INSTRUMENTS
'AS850 logic diagram (positive logic) (see inset for 'AS851)
00 (8)
01 (7)
02 (6)
03 (5)
04 (4)
05 (3)
06 (2)
..en
!::
::)
(J
07 (1)
a:
(J
08 (27) en
<t
W
09 126) C
Z
010
(251 <t
en
...J
011 (24)
<t
012(231
(22)
013
121)
014
015 (20)
1283
TEXAS 2-573
INSTRUMENlS
Supply voltage, Vee ....................................................... " 7 V
Input voltage .............................................................. 7 V
Operating free-air temperature range: SN54AS850, SN54AS851 ............ , - 55 °e to 125°e
SN74AS850, SN74AS851 ................ ooe to 70 0 e
Storage temperature range .......................................... - 65 °e to 150 °e

SN54AS850 SN74AS850
UNIT
10l Low-level output current 32 48 mA
tw Pulse duration
I eLK high ns
I eLK low
tsu Setup time, select inputs before eLK t ns
th Hold time. select inputs after eLK t ns

SN54AS850 SN74AS850
V,K Vee = 4.5 V, I, = -18 mA -1.2 -1.2 e
VOH Vee = 4.5 V. 10H = -12 mA 2.4 3.2 V
Vee = 4.5 V, 10H = -15 mA 2.4 3.3
Vee = 4.5 V. 10L = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, 10L = 48 mA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 50 50 p.A
IOZL Vee = 5.5 V. Vo = 0.4 V -50 -50 p.A
Vee = 5.5 V, V, = 7 V 0.1 0.1 mA
"
I'H Vee = 5.5 V. V, = 2.7 V 20 20 p.A
',L Vee = 5.5 V. V, = 0.4 V mA
10+ Vee = 5.5 V. Vo = 2.25 V -30 -112 -30 -112 mA
Vee = 5.5 V
I Outputs active mA
lee
I Outputs disabled
tAli typical values are at Vee = 5 V. TA = 25°e. .
*The output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current. lOS'
1283
2-574 TEXAS
INSTRUMENTS

Vce = 4.S v to S.S V.
CL = so pF.
FROM TO R1 = SOO O.
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = SOO O.
TA = MIN to MAX
SNS4AS8S0 SN74AS8S0
f max MHz
tpLH 4.7 4.7
Any D V ns
tpHL S 5
tpLH S.S S.5
Any D W ns
tpHL 6.2 6.2
tpLH 10.2 10.2
CLK Y ns
tpHL 8.3 8.3
tplH 8.8 8.8
CLK W ns
tpHL 11.6 11.6
tpZH 4 4
G Y ns
tpZL 4.9 4.9
tpHZ 3.1 3.1
G Y n's
tpLZ 3.9 3.9
tpZH 4 4
G W ns
tpZL 4.9 4.9
tpHZ 3.1 3.1
IT W ns
tpLZ 3.9 3.9
tpZH 4 4
GY Y ns
tpZL 4.9 4.9
tpHZ 3.1 3.1 en
tpLZ
GY Y
3.9 3.9
ns
t::
tpZH 6.8 6.8 :::l
GW W ns
tpZL 6.6 6.6 U
tpHZ
GW W
4.3 4.3 ex:
ns
tpLZ S.6 5.6 U
t All typical values are at Vee = 5 V. T A = 25 De. en
NOTE1: For load circuit and voltage waveforms, see page 1-12. «
c
2
«
en
..J
«
1283
TEXAS 2-575
INSTRUMENTS
1 OF 16 DATA SELECTROS/MULTIPLEXERS WITH 3-STATE OUTPUTS

SN54AS851 SN74AS851
UNIT
10H High·level output current -12 -15 mA
10L Low-level output current ,32 48 mA
tw Pulse duration
I e high ns
Ie low
tsu Setup time, select inputs before es t ns
th Hold time, select inputs after es t ns

SN54AS851 SN74AS851
VIK Vee = 4.5 V, . II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V, IOH = -12 mA 2.4 3.2 V
-
Vee = 4.5 V, IOH = -15 mA 2.4 3.3
Vee = 4.5 V, IOL = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, 10L = 48 mA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7V 50 50 p.A
10ZL Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
l> = VI = 7 V
r- II Vee 5.5 V, 0.1 0.1 mA
en IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
l> 10+ Vee = 5.5 V, Vo = 2.25 V -30 - 112 -30 -112 mA
:2 lOutputs active
C lee Vee = 5.5 V
I Outputs disabled mA
l>
en tAli typical values are at Vee = 5 V, TA = 25°e.
tThe output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current, lOS'
n Additional information on these products can be obtained from the factory as it becomes available.
:Jl
n
c
=t
en
1283
2-576 TEXAS
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 fl.
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 fl.
TA = MIN to MAX
SN54AS851 SN74AS851
tpLH 4.7 4.7
Any D Y ns
tpHL 5 5
tpLH 5.5 5.5
Any D W ns
tpHL 6.2 6.2
tPLH 7.9 7.9
SO. S1. S2. S3 Y ns
tpHL 9.6 9.6
tPLH 10.1 10.1
50.51.52.53 W ns
tpHL 11.1 11.1
tpLH 12 12
5C Y ns
tpHL 12.5 12.5
.tpLH 12 12
5C W' ns
tpHL 13 13
tpZH 4 4
G Y ns
tpZL 4.9 4.9
tpHZ 3.1 3.1
G Y ns
tpLZ 3.9 3.9
PZH 4 4
G W ns
tpZL 4.9 4.9
tpHZ 3.1 3.1
IT
tPLZ
W
3.9 3.9
ns
en
tpZH
GY Y
4 4
ns !::
tpZL 4.9 4.9 :::J
tpHZ 3.1 3.1 U
tpZL
GY Y
3.9 3.9
ns
a:
tpZH 6.8 6.8 U
GW W ns
6.6 6.6
tpZL
tpHZ 4.3 4.3
en
tPLZ
GW W
5.6 5.6
ns <t
c
NOTE 1: For load circuit and voltage waveforms, see page 1·12. :2
<t
en
...J
<t
1283
TEXAS 2-577
INSTRUMENTS
The AS850 or AS851 can be used as a 1~of-16 Boolean function generator. Figure 1 shows the AS850
I I I
in one example.
{>o-
'AS138 ~
G"2A",
Gl
oU ~'
"lfD
lr-....
G2B" 2~
3~ ,
4'
~1
7! 5'
6~
7 .....
~
•
-,
I .,..
~
'AS850
~GW
ClK
50
Sl
S2
53
DO
---
DISABLE ~
.L5
Dl y
D2
D3
D4
D5 ::::.... W
D6
~
D8
.-
D9
Dl0
'A5163 Dll
ClR" --f D12
-~
lOA~ D13
RCO
~
Ek
COUNT
DISABLE ENP
~
CLOCK
ClK
~ ,.. D--
~~!p
OA
A
B
C
D
OB
OC
~.
Y>----J
~
Y>~
FIGURE 1-1·0F·16 BOOLEAN FUNCTION GENERATOR
1283
2-578 TEXAS
INSTRUMENTS
'AS850
MUX
CLOCK--------------------~r-~~
A y
B
W
~ ,~
'AS850
y
I ....
. ",.~
. ';m~u~ I.,,·.'r
MUX
W
en
!::
:J
U
SO
S1
a::
S2 U
S3 en
<t
y
C
2
<t
w en
-I
<t
013
014
015
FIGURE 2-1-0F-32 DATA/SELECTOR/MULTIPLEXER
1283
TEXAS 2-579
INSTRUMENTS
C L O C K - - - - - - - - - - - - - - - - - -__--------------------------~
'AS850 'AS850
r-----~~~~,~~ MUX
~
CLK
~>
-r----s,- ,
S2 S2
S3 S3
A-----------+1-r;-.
B----------~-+-~ y r-- y-
c----------~-r.
D -----------1-'.
wt:::.....-
'AS139
-~::::...- >--y
-2 1::::"'-
2~;_r;-+_r+_--------------_r~
G -1::::. EN 3 .,:'~_+_-+-Hf_+--------------~I_+...,
i-...- 'AS850 'AS850
-- I-'~""- ,-+-+-+--il-+----"G~ ~-r+_r+~G~~
-- r__.. MUX
~
MUX
t:::... Ill!:::.
:::::..... ~ ~
~
~I> ~I>
Sl ----st
S2 S2
S3 S3
FIGURE 3-1-0F-64 DATA SELECTOR/MULTIPLEXER
1283
2-580 TEXAS
INSTRUMENTS
POST OFFICE BOX 225012. DALLAS, TEXAS 75265
8·BIT UNIVERSAL TRANSCEI~ER PORT CONTROLLERS
D2810. DECEM8ER 1983
o Included Among the Package Options are SN54AS852 ... JT PACKAGE

Compact, 24·Pin, 300-mil-Wide DIPs and SN74AS852 ... NT PACKAGE
Both 28-Pin Plastic and Ceramic Chip (TOP VIEW)
Carriers
so VCC
o Buffered 3-State Outputs Drive Bus Lines S1 ClK
Directly S2 SERIN
A1 B1
o Cascadable to n-Bits
A2 B2
o Eight Selectable Transceiver/Port Functions: A3 B3
A4 B4
A to B or B to A A5 B5
Register to A or Register to B A6 B6
Shifted to A from B or Shifted to B from A A7 B7
Off-Line Shifts (A and B Ports Transceiving A8 B8
or in High-Impedance State) GND 08
Register Clear
o Particularly Suitable for Use in Diagnostics SN54AS852 ... FH PACKAGE
Circuitry SN74AS852 ... FN PACKAGE
o Serial Register Provides: (TOP VIEW)
Z
Parallel Storage of Either A or B Input Data U ~
N..-OU U..J w
a:
(/)(/)(/)Z>U(/)
Serial Transmission of Data from Either
A or B Port 282726
A1 B1
o Dependable Texas Instruments Quality and B2
Reliability B3
NC NC
B4 en
B5 t::
A6 ::::>
12131415161718 C,.)
..... c:oOUc:oc:o ..... a:
<!<!ZZOCDCD C,.)
(,!)
NC - No internal connection en
description <t
, .
'0
The' AS852 features two 8-bit I/O ports (A 1-A8 and 81-88), and 8-bit parallel-load, serial-in, parallel-out
shift register, and control logic. With these features, this device is capable of performing eight selectable
z
transceiver or port functions, depending on the state of the three select lines SO, S 1, and S2. These functions
<t
include: transferring data from port A to port 8 or vice versa (i.e., the transceiver function), transferring en
data from the register to either port, serial shifting data to either port from the opposite port, performing ...J
off-line shifts (with A and 8 ports in high-impedance state I. and clearing the register. The 'AS852 can <t
simultaneously transfer data from A to 8 or 8 to A and perform an off-line serial shift of data in the register.
Synchronous parallel loading of the internal register can be accomplished from either port on the positive
transition of the clock while serially shifting data in via the SERIN input. The' AS852 is ideally suited for
applications implementing diagnostic circuitry to enhance system verification and/or fault analysis. All serial
data is shifted right. All outputs are buffer-type outputs designed specifically to drive bus lines directly
and all are 3-state except for 08, which is a totem-pole output.
The SN54AS852 is characterized for operation over the full military temperature range of - 55°C to 125°C.
The SN74AS852 is characterized for operation from ooe to 70°C.
1283 ThIs document contalnllnlonnatlon on • product under

development. Texa.lnstruments r...rve. the right to TEXAS
chango or dlscontlnuo this product without notlco. INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEXAS 75265 2-581
8·BIT UNIVERSAL TRANSCEIVER PORT CONTROLLERS

r---------------~~--------------------~
l>
r-
en
FOUR IDENTICAL CHANNELS NOT SHOWN
l> INPUTS/OUTPUTS NOT SHOWN:
:2 (6) A3 (19) 83
C (7) A4 (18) 84
(8) A5 (17) 85
l>
en (9) A6 (16) 86
n
:l]
n
c
-t
en
1283
2-582 TEXAS
INSTRUMENTS
FUNCTION TABLE
MODE PORT
CLOCK SERIN Al 01 Bl A202 B2 A3 03 B3 A4 04 B4 AS as B5 AS as BS A7 07 B7 AB as BS
S2 Sl SO FUNCTION
L L L H or L X Z On Al Z On A2 Z On A3 Z On A4 Z On A5 Z On AS Z On A7 Z On AS
A TO S
L L L I X Z A1 A1 Z A2 A2 A A3 A3 Z A4 A4 Z A5 A5 Z A6 A6 Z A7 A7 Z A8 A8
L L H H or L X 81 On Z 82 On Z 83 On Z 84 On Z 85 On Z 86 On Z 87 On Z 88 On Z
8l0A
L L H I X B1 B1 Z 8282 Z 8383 Z B484 Z 8585 Z B686 Z 8787 Z 8888 Z
L H L H or L X X On 01 X On 02 X On 03 X On 04 X On 05 X On 06 X On 07 X On 08
ON TO 8N
L H L I X Z A1 A1 Z A2 A2 Z A3 A3 Z A4 A4 Z A5 A5 Z A6 A6 Z A7 A7 Z A8 A8
L H H H or L X 01 On X 02 On X 03 On X 04 On X 05 On X 06 On X 07 On X 08 On X
ON TO AN
L H H I X 81 81 Z 8i 82 Z 8383 Z 8484 Z 8585 Z 8686 Z 8787 Z 8888 Z
H L L H or L X Z On A1 Z On A2 Z On A3 Z On A4 Z On A5 Z On A6 Z On A7 Z On A8 SHIFT
H L L I H Z H A1 Z 01 A2 Z 02 A3 Z 03 A4 Z 04A5 Z 05 A6 Z 06 A7 Z 07 A8 AND
H L L I L Z L A1 Z 01 A2 Z 02 A3 Z 03 A4 Z 04A5 Z 05 A6 Z 06 A7 Z 07 A8 A TO 8
H L H H or L X 81 On Z 82 On Z 83 On Z 84 On Z 85 On Z 86 On Z 87 On Z 88 On Z SHIFT
H L H I H 81 H Z 82 01 Z 83 02 Z 84 03 Z 85 04 Z 86 05 Z 87 06 Z 88 07 Z AND
H L H I L 81 L Z 82 01 Z 83 02 Z 84 03 Z 85 04 Z 86 05 Z 87 06 Z 88 07 Z 8 TO A
H H L H or L X Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z
H H H I H Z H Z Z 01 Z Z 02 Z Z 03 Z Z 04 Z Z 05 Z Z 06 Z Z 07 Z SHIFT
H H H I L Z L Z Z 01 Z Z 02 Z Z 03 Z Z 04 Z Z 05 Z Z 06 Z Z 07 Z
H H H H or L X Z On Z Z On Z On Z Z On Z Z On Z Z an Z Z On Z Z On Z
CLEAR
H H H I X Z L Z Z L Z Z L Z Z L Z Z L Z Z L Z Z L Z Z L Z
n = level of 0n(n = 1,2, ... 8) established on most recent I transition of CLK. 01 through 08 are the shift register outputs; only 08 is available externally.
The double inversions that take place as data travels from port to port are ignored in this table.
logic symbol [PORT CONTROLLER)

so
Sl SRG8 en
S2
!:::
CLK ::::>
u
a:
SERIN
(21) u
A1 (0/2)100 Bl en
(1/3)100
12 0/4
<C
13 2
Z14 o
:;;'1 1=0 (20)
Z
A2 (0/2)100 B2 <C
1S (1/3)100
15 0/4
en
...J
A3
Z17
(19) <C
B3
(18)
A4
(17) : :
(16)
BS
(15) B7
:;;'1 1=0 :;;'1

(14)
A8 (0/2)100 (0/2/4)[>\7 B8
33 0/4 Z34
(1/3)100 35 (13) as
35,3 Z35
1283
TEXAS 2-583
INSTRUMENTS
absolute maximum ratings over free-air temperature range

Input voltage: All inputs .................................................... " 7 V
1/0 ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Voltage aplied to a disabled 3-state output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54AS852 ....................... - 55°C to 125°C
SN74AS852 . . . . . . . . . . . . . . . . . . . . . . . . . .. ooe to 70°C

SN54AS852 SN74AS852
UNIT
Vil low-level input voltage O.S O.S V
A1-AS.81-88 -12 -15
IOH High-level output current rnA
08 -2 -2
A1-A8.81-88 32 48
IOl low-level output current rnA
08 20 20
tw Duration of clock pulse ns
A1-A8.81-88
tsu Setup time before ClK I SERIN ns
SO. S1. S2
A1-A8.81-88
0 a ns
th Hold time. data after ClK I SERIN
SO. S1. S2 a 0
l> TA Operating free-air temperature -55 125 a 70 °C
r-
en Additional information on these products can be obtained from the factory as it becomes available.
l>
2
C
l>
en
(")
::D
(")
C
-i
en
1283
2-584 TEXAS
INSTRUMENTS
SN54AS852 SN74AS852
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
A1-AB Vee = 4.5 V, 10H = -12 rnA 2.4 3.2
VOH B1-BB Vee = 4.5 V, 10H = -15 rnA 2.4 3.3 V
All outputs Vee = 4.5 V to 5.5 V, 10H = -2 rnA vee -2 Vee- 2
Vee = 4.5 V, 10l = 32 rnA 0.25 0.5
All outputs except a8
VOL Vee = 4.5 V, 10l = 48 rnA 0.35 0.5 V
a8 Vee = 4.5 V, 10l = 20 rnA 0.25 0.5 0.25 0.5
50,51,52 0.3 0.3
Vee = 5.5 V, VI = 7 V
II elK and 5ERIN 0.1 0.1 rnA
A1-A8, B1-B8 Vee = 5.5 V, VI = 5.5 V 0.2 0.2
50,51,52 60 60
IIH elK and 5ERIN Vee = 5.5 V, VI = 2.7 V 20 20 p.A
A1-A8, B1-B8 t 70 70
50,51,52 -2 -2
III elK and 5ERIN Vee = 5.5 V, VI = 0.4 V -0.3 -0.3 rnA
A1-A8, B1-B8 t -0.35 -0.35
Except a8 -30 -112 -30 -112
10§ Vee = 5.5 V, Va = 2.25 V rnA
a8 -20 -112 -20 -112
lee Vee = 5.5 V 122 122 rnA

tFor 1/0 ports, the parameters IIH and III include the output currents 10ZH and 10Zl, respectively.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS.

Vee = 4.5 V to 5.5 V,
en
CL = 50 pF. !:::
R1 = 500 D, ::::>
FROM TO R2 = 500 D, u
PARAMETER
UNIT a:
SN54AS852 c)N74AS852 u
en
f rnax 75 75 MHz
~
9.5 9.5
tplH
tpHl
Any A port Any B port
8 8
ns c
tPLH 9.5 9.5 z
tpHl
Any B port Any A port
8 B
ns ~
tplH
50,51,52
Any A or B 12 12
ns
en
tpHl port 12 12 ....I
tplH Any A or B 6.5 6.5 ~
elK ns
tpHl port 12.5 12.5
tPLH 9 9
elK a8 ns
tpHl 9 9
tpHZ 6 6
ns
tplZ Any A or 8 6 6
50,51,52
tpZH port 10 10
ns
tpZl 10 10
t All typical values are at Vee = 5 V', T A = 25°e.

1283
TEXAS 2-585
INSTRUMENTS
POST OFFICE BOX 225012 • DAllAS. TEXAS 75265
BUS A TO BUS B OR BUS B TO BUS A OR

SERIAL TRANSMISSION SERIAL TRANSMISSION
SERIAL IN SERIAL IN
CLK CLK
I REG
I I
I I I
AI IB IB
I I I
I I I
I I REG I
1m I
IB AI
I I
IB
»
r- I I I
OO I I I
»
2
C SERIAL
SERIAL
»
00
OUT OUT
n SERIAL IN TO A PORT SERIAL IN TO B PORT

::JJ SERIAL IN _ _ _ _ _- - , SERIAL IN _ _ _ _ _---.
n CLK----....., CLK-----,
C ~~~~~
~
00 I I
I I
IB Hi-Z Hi-Z IS
I I
I I
SERIAL SERIAL
OUT OUT
1283
2-586 TEXAS
INSTRUMENTS
• Included Among the Package Options are SN54AS856 •.• JT PACKAGE

Compact, 24-Pin, 300-mil-Wlde DIPs and SN74AS856 •.. NT PACKAGE
Both 2B-Pin Plastic and Ceramic Chip (TOP VIEW)
Carriers
OEB VCC
o Buffered 3-State Outputs Drlvo Bus Lines OEA ClK
Directly MODE SERIN
o Cascadable to n-Bits
A1 B1
A2 B2
o Eight Selectable Transceiver/Port Functions: A3 B3
- B to A
A4 B4
- Register to A and/or B
A5 B5
- Off-Line Shifts (A and B Ports in High- A6 B6
Impedance State I A7 B7
- Shifted to A and/or B A8 B8
GND 08
o Particularly Suitable for Use in Diagnostics
. Analysis Circuitry SN54AS856 ... FH PACKAGE
o Serial Register Provides: SN74AS856 .. , FN PACKAGE
(TOP VIEW)
- Parallel Storage of Either A or B Input
W Z
-
Data
Serial Transmission of Data from Either
°l<t:lal
U~a:
°WWUU..Jw
~ooz>UU)
A or B' Port
4 3 2 1
- Readback Mode B to A
A1 5 B1
o Dependable Texas Instruments Quality and A2 6 B2
Reliability A3 7 B3
NC
NC
A4 B4 en
A5 B5 !::
A6 B6 ::>
u
12 131415161718
a::
u
en
<t
description C
The' AS856 features two 8-bit I/O ports (A 1-A8 and B 1-B8), an 8-bit parallel-load, serial-in, parallel-out z
shift register, and control logic. With these features, this device is capable of performing eight selectable <t
transceiver or port functions, depending on the state of the three control lines OEA, OEB, and MODE. These en
..oJ
functions include: transferring data from port A to port B or vice versa (i.e., the transceiver function), serial
shifting data to either or both ports, and performing off-line shifts (with A and B ports active as transceivers <t
in a high-impedance state). Synchronous parallel loading of the internal register can be accomplished from
either port on the positive transition of the clock while serially shifting data in via the SERIN input. The
, AS856 is ideally suited for applications needing signature-analysis circuitry to enhance system verification
and/or fault analysis. All serial data is shifted right. All outputs are buffer-type outputs designed specifically
to drive bus lines directly and all are 3-state except for 08, which is a totem-pole output.
The SN54AS856 is characterized for operation over the full military temperaure range of - 55°C to 125°C.
The SN74AS856 is characterized for operation from DoC to 70°C.

This document contains infonnation on 8 product under
change or discontinue this product without notic •. INSTRUMENTS
POST OFFICE BOX 2250i2 • DALLAS, TEXAS 75265

o.rn~/1~I __-a >-__________________________________ ~
OEA ..:,:(2:;.:..1_-0 >-____--,

MODE ..:,:(3:;.:..1_--t
ClK~(2~3~1__~ ~~----4-~------------~
SE RIN ...:.:(2,-21'-----<1 >------~-+-+--.
(21) B1
(201 B2
~
»
r- FOUR IDENTICAL CHANNELS NOT SHOWN
en INPUTS/OUTPUTS NOT SHOWN:
»
2
(61 A3
(7) A4
(191 B3
/181 B4
C (81 A5 (171 B5
»
en
(91 A6 (161 B6
Q
::JJ I
("') (151
c x)-+-'-4~- B7
=i
en
(141 B8
(131 a8
1283
2-588 TEXAS
INSTRUMENTS
FUNCTION TABLE
MODE
CLOCK SERIN A1 01 B1 A2 02 B2 A3 03 B3 A4 04 B4 A5 05 B5 AS as BS A7 07 B7 AB 08 B8 FUNCTION
MODE OEA me
L L L H or L X 010101 02 02 02 03 03 03 04 04 04 05 05 05 06 as 06 07 07 07 08 08 08
FEEDBACK
L L L t X 010101 02 02 02 03 03 03 04 04 04 05 05 05 06 06 06 07 07 07 08 08 08
L L H H or L X 8101 Z B2 02 Z B3 03 Z B4 04 Z B5 05 Z B6 06 Z B7 07 Z B8 08 Z B to A
L L H t X Bl Bl Z 82 B2 Z B383 Z B4 B4 Z B5 B5 Z B6 B6 Z B7 B7 Z B8 B8 Z Ato a
L H L H or L X Z 0101 Z 02 02 Z 03 03 Z 0404 Z 05 05 Z 06 06 Z 07 07 Z 0808 Ato a
L H L t X Z Al Al Z A2 A2 Z A3 A3 Z A4 A4 Z A5 A5 Z A6 A6 Z A7 A7 Z A8A8 a to B
L ·H H H or L X Z 01 Z Z 02 Z Z 03 Z Z 04 Z Z 05 Z Z 06 Z Z 07 Z Z 08 Z
A to a
L H H t X Z Al Z Z A2 Z Z A3 Z Z A4 Z Z A5 Z Z A6 Z Z A7 Z Z A8 Z
H L L H or L X alan 01 02 an 02 03 On 03 04 On 04 05 On 05 06 On 06 07 On 07 08 On 08 SHIFT
H L L t H H H H 010101 02 02 02 03 03 03 04 04 04 05 05 05 06 06 06 07 07 07 TO
H L L t L L L L 010101 02 02 02 03 03 03 04 04 04 05 05 05 06 06 06 07 07 07 A and B
H L H H or L X alan Z 02 On Z 03 On Z 04 On Z 05 0nZ 06 an Z 07 On Z 08 On Z SHIFT
H L H t H H H Z 0101 Z 02 02 Z 03 03 Z 0404 Z 05 05 Z 0606 Z 07 07 Z TO
H L H t L L L Z 0101 Z 02 02 Z 03 03 Z 0404 Z 05 05 Z 06 06 Z 07 07 Z A
H H L H or L X Z On 01 Z On 02 Z On 03 Z On 04 Z an 05 Z On 06 Z On 07 Z On 08 SHIFT
H H L t H Z H H Z 0101 Z 02 02 Z 03 03 Z 0404 Z 05 05 Z 06 06 Z 07 07 TO
H H L t L Z L L Z 0101 Z 02 02 Z 03 03 Z 0404 Z 0505 Z 06 06 Z 07 07 8
H H H H or L X Z On Z Z an Z Z On Z Z an Z Z On Z Z On Z Z On Z Z On Z
SHIFT
H H H t H Z H Z Z 01 Z Z 02 Z Z 03 Z Z 04 Z Z 05 Z Z 06 Z Z 07 Z
H H H t L Z L H Z 01 Z Z 02 Z Z 03 Z Z 04 Z Z 05 Z Z 06 Z Z 07 Z
n = level of 0n(n = 1, 2 ... 8) established on most recent t transition of CLK. 01 through 08 are the shift register outputs; only 08 is available externally.
The double inversions that take place as data travels from port to port are ignored in this table.
logic symbol
(PORT CONTROLLER)
en
OEB
(1)
" EN3 t::
OEA
(2)
" EN4 SRGB ::>
MODE
(3)
L-
.r-.. MO u
Ml
a:
ClK
(23)
.,
Z2
;;'1
2
.,I> 1 ->-IC5
1-0
r- U
(22)
1,50 en
SERIN
Al
(4)
Z7
Z6 6
7 0,50 3[>'V
.
(21)
Bl <t
4- V<)4 ZB L.J C
- B,O
- 9,1 Z9- 2
;;'1 1=0 <t
~)
(5)
A2
r....
Z10
V<)4
10 0,50 3[>V
Z11
82
en
...J
-
-
11,0
12,1 Z12-
<t
(6) (19)
A3 B3
(7) (1B)
A4 B4
(B) (17)
A5 -'" 85
(9) (16)
A6 B6
(10) .. (15)
A7 87
;;'1 1-0
(11) (14)
AB Z2B 2B- 0,50 3[>V BB
4-
-
V<)4
29,0
Z29
Z30
~(13) OB
- 30,1
1283
TEXAS 2-589
INSTRUMENTS
absolute maximum ratings over free-air temperature range

Input voltage: All inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
. I/O ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54AS856 ....................... - 55°C to 125°C
SN74AS856 ........................... ooe to 70°C
Storage temperature range . < • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • - 65°C to 1 50°C

SN54AS856 SN74AS856
UNIT
Vil low-level input voltage 0.8 O.S V
Al-AS, Bl-BS -12 -15
OS -2 -2
Al-AS, Bl-BS 32 4S
OS 20 20
Al-AS, Bl-BS SERIN
tsu Setup time before ClK t ns
OEB, OEA, MODE
Al-AS, Bl-BS SERIN 0 0
th Hold-time, data after ClKt ns
II1II TA Operating free-air temperature

OEB, OEA, MODE 0
-55 125
0
0 70 °c
l> Additional Information on these products can be obtained from the factory as it becomes available.
r-
en
l>
2
C
l>
en
Q
:xl
(")
c
=i
en
1283
2-590
. TEXAs
INSTRUMENTS

SN54AS856 SN74AS856
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
Al·A8 Vee = 4.5 V, IOH = -12 rnA 2.4 3.2
VOH Bl·B8 Vee = 4.5 V, IOH = -15 rnA 2.4 3.3 V
All outputs Vee = 4.5 V to 5.5 V, IOH = -2 rnA vcc- 2 Vce- 2
Vee = 4.5 V, IOl = 32 rnA 0.25 0.5
All outputs except 08
VOL Vee = 4.5 V, IOl = 48 rnA 0.35 0.5 V
08 Vee = 4.5 V, IOl = 20 rnA 0.5 0.5
OEB, OEA, MODE 1 1
Vee = 5.5 V, VI = 7 V
II elK and SERIN 0.1 0.1 rnA
Al·A8, Bl·B8 Vee = 5.5 V, VI = 5.5 V 0.2 0.2
OEB, OEA, MODE 800 400
IIH elK and SERIN Vee = 5.5 V, VI = 2.7 V 20 20 p.A
Al·A8, Bl·B8+ 70 70
OEB, OEA, MODE -2 -2
III elK and SERIN Vee = 5.5 V, VI = 0.4 V -0.3 -0.3 rnA
A1·A8, Bl·B8+ -0.35 -0.35
Except 08 -30 -112 -30 -112
IO§ Vee = 5.5 V, Vo = 2.25 V rnA
08 -20 -112 -20 -112
lec Vee = 5.5 V 118 118 rnA

+For 1/0 ports. the parameters IIH and III include the output currents 10ZH and 10Zl, respectively.

Vcc = 4.5 V to 5.5 V, !::
Cl = 50 pF, ::::>
R1 = 5000, uex:
FROM TO R2 = 5000,
PARAMETER
UNIT
U
SN54AS856 SN74AS856
en
f rnax
MIN Typt MAX
75
MIN Typt MAX
75 MHz
«
tplH 9.5 9.5 o
Any A port Any B port ns
z
tpHl
tplH
Any B port Any A port
8
9.5
8
9.5
ns
«
tpHl
Any A or B
8
12
8 en
..J
12
tPlH
tpHl
OEB, OEA, MODE
port 12 12
ns
«
tplH Any A or B 6.5 6.5
elK ns
tpHl port 12.5 12.5
tplH 9 9
ClK 08 ns
tPHl 9 9
tpHZ 6 6
ns
tplZ Any A or B 6 6
OEB, OEA, MODE
tpZH port 10 10
ns
tpZl 10 10

1283
TEXAS 2-591
INSTRUMENTS
IB
l>
r-
en
l>
2.
C
l>
en
(')
::u
(')
c:
=i
en
2-592
HEX 2·TO·1 UNIVERSAL MULTIPLEXERS
02661, DECEMBER 1982-REV15EO DECEMBER 1983
• Selects True or Complementary Data SN54ALS857,SN54AS857 ... JTPACKAGE

SN74ALS857,SN74AS857 ... NTPACKAGE
• Performs AND/NAND (masking) of A or B Operand (TOP VIEW)
• Cascadable to Expand Number of Operands 50 1 U24 VCC
1A 2 23 51
• Detects Zeros on A or B Operands 1B 3 22 6A
1Y 4 21 6B
• 3-State Outputs Interface Directly with System Bus 2A 5 20 6Y
2B 6 19 5A
• Included Among the Package Options Are 24-Pin, 2Y 7 18 5B
300-Mil-Wide DIPs and Both 28-Pin Plastic and 3A 8 17 5Y
Ceramic Chip Carriers 3B 9 16 4A
3Y 10 15 48
• Dependable Texas Instruments Quality and Reliability OPER=O 11 14 4Y
GNO 12 13 COMP
description
SN54ALS857, SN54AS857 ... FH PACKAGE
The 'ALS857 and 'AS857 are hextuple 2-line to 1-line
SN74ALS857, SN74AS857 ... FN PACKAGE
multiplexers with three-state outputs, The devices can provide
eitper true (COMP low) or inverted (COMP high) data at the Y
outputs, In addition, the 'ALS857 and 'AS857 perform the
logical AND function (A,B) and the clear function as well. The
four modes of operation are:
For chip carrier information
Select A data inputs,
contact factory
Select B data inputs,
AND A inputs with B inputs,
Clear
In either of the first two modes, OPER = 0 is high if all the

selected A or B inputs are low.
The six Y outputs and the OPER = 0 output are all three-state and en
rated at 12 mA and 24 mA IOL for the SN54ALS857 and t::::
SN74ALS857, respectively, and at 32 mA and 48 mA IOL for :::l
the SN54AS857 and SN74AS857, respectively. All outputs can
(.)
be placed into the high-impedance state by applying a high level
logic symbol a::
to the COMP, SO, and S1 inputs simultaneously. The complete (.)
function table is shown below. en
The SN54ALS857 and SN54AS857 are characterized for opera- «
tion over the full military temperature range of - 55°C to c
125°C. The SN74ALS857 and SN74AS857 are characterized z
for operation from OOC to 70°C. «
1411Y
en
FUNCTION TABLE ..J
COMP S1 SO Y OUTPUTS OPER=ZERO 171 2Y «
L L L A H = all A inputs L 1101 3y
L L H B H = all B inputs L
1141 4y
L H L A·B Z
L H H L L 1171
5Y
H L L A H = all A inputs L
1201
6y
H L H S; H = all B inputs L
H H L A-B z I>
1 617 1111 OPER-O
H H H Z Z

1289
TEXAS 2-593
INSTRUMENTS
'ALS857 logic diagram (positive logic)
(1)
SO--------__~--,
~----------------------------------------
(23)
S1
(13)
COMP
(2)
1A
(4) 1Y
(3)
18
(5)
2A
28
(6) ~2Y
(8)
3A
38
(9) DETAILS OF r-J.!2l- 3Y
FOUR IDENTICAL CHANNELS
III 4A
48
(16)
(15)
5A (19)
NOT SHOWN
~4Y
l> 58 (18) j--J.!ZL5Y
r-
en
l> 6A (22)
2
C (20) 6Y
68 (21)
l>
en
Q
:xl
o
c ")-_ _ _ _ _...;(~1...;.1):.. OPER = 0
=i
en
1283
2-594 TEXAS
INSTRUMENTS
'AS857 logic diagram (positive logic)
so (11
--"""\.
~
1 ......... - J
Sl
(231 =-=c>
--~
"V"
-"".
"V
caMP (131 .........
..........
lA
121 Y> -
~~
I--'
18
(31 1 ~
~
~ (41
Le[> 1Y
~-
~-
B?r~
T
2A
(51
161
.I
J
'''''., ~-
.......... - ...
~ 2Y
28
181~
k{> ,
.I
3A
191 r ;
38
~ 3Y
-~
~
"61~
DETAilS OF
FOUR IDENTICAL CHANNELS
4A
(151
.
I
~
NOT SHOWN
48
; ~ 4Y
SA
, . It>
(181
k{> .:
~
~
58
~ 5Y-
lc(> I
I
• ... ~ '1" I'
1221Lt>
6A
68
(21) 1 :~~
~
(20)
Let> ~Yr~
6Y
1
T
=8=1
I II
---,
- --,
y y (111
:1 OPER=O
Pin numbers shown are for JT and NT packages_
1283
TEXAS 2-595
INSTRUMENTS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS857 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 DC to 125 DC
SN74ALS857 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 DCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , - 65 DC to 150 DC

UNIT
IOL Low-level output current 12 -24 mA
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
III VOH
Vee - 4.5 V to 5.5 V, IOH = -0.4 mA
Vec = 4.5 V,
Vee = 4.5 V,
IOH = -1 mA
IOH = -2.6 mA
Vee- 2
2.4 3.3
Vee- 2
2.4 3.2
V
:t- Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4

r- VOL
Vee = 4.5 V, 0.35 0.5
V
m IOZH Vee = 5.5 V,
IOL = 24 mA
Va = 2.7 V 20 20 /lA
:t- IOZL Vee = 5.5 V, Va = 0.4 V -20 -20 /lA
z II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
C IIH Vee = 5.5 V, VI = 2.7 V 20 20 /lA
:t- IlL Vee = 5.5 V, VI = 0.4 V -0.2 -0.2 mA
m lot Vee = 5.5 V, Va = 2.25 V -15 -70 -15 -70 mA
o Yee = 5.5 V,
lee I Outputs low 16 33 16 33 mA
::D See Note 1
I
o Outputs disabled 18 36 18 36
C tAli typical values are at Vee = 5 V, TA = 25°C.

==i ~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
C/) NOTE 1: ICC is measured with all possible inputs grounded while achieving the stated output conditions.
1283
2-596 TEXAS
INSfRUMENTS
switching characterisitcs (see Note 1)
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
R1 = 500 Q,
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54ALS857 SN74ALSB57
MIN MAX MIN MAX
A or B Y
tpd 4 18 4 14 ns
(COMP high) (Inverting)
A or B Y
tpd 4 18 4 14 ns
(COMP low) (Noninverting)
tpd SO or S1 y 7 37 7 33
tpd COMP Y 6 22 6 18
ns
tpd A or B OPER=O 5 45 5 37
tpd SO or S1 OPER=O ? 30 5 23
ten 7 38 7 35
SO or 51 y ns
tdis 2 29 2 23
ten· 8 27 8 24
COMP Y ns
tdis 6 27 6 21
ten 6 24 6 20
50 OPER=O ns
tdis 11 34 11 27
ten 6 28 6 25
51 OPER=O ns
tdis 3 23 3 19
ten 9 30 9 25
COMP OPER=O ns
tdis 6 24 6 20
tpd = tpLH or tpHL

ten = tpZH or tpZL
en
tdis = tpHZ or tpLZ !::
NOTE 1: For load circuit and voltage waveforms, see page 1-12. ::J
U
a:
U
en
«
c
2!
«
en
-I
«
1283
TEXAS 2-597
INSfRUMENTS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied t~ a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS857 . . . . . . . . . . . . . . ~ . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS857 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 0eto700e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , - 65 °e to 150 °e
SN54AS857 SN74AS857,
UNIT
Vee Supply voltage 4.5 5 5.5 4.5 5 5:5 V
Y Outputs -12 -15
OPER = 0 -2 -2
Y Outputs 32 48
OPER = 0 20 20
TA Operating free·air temperature - 55 125 0 70 °e
ItJ PARAMETER TEST CONDITIONS

MIN
SN54AS857
Typt MAX MIN
SN74AS857
Typt MAX
UNIT
»
r-
VIK Vee
Vee
= 4.5
= 4.5
V,
V,
II
IOH
= -18 rnA
= -12 rnA 2.4 3.2
-1.2 -1.2 V
en VOH
Y Outputs
Vee = 4.5 V, IOH = -15 rnA 2.4 3.3 V
»
:2
All Outputs
Y Outputs
Vee
Vee
= 4.5
= 4.5
V to 5.5 V,
V,
IOH = -2 rnA
IOl = 32 rnA
vee- 2
0.35 0.5
vee- 2
VOL Vee = 4.5 V, IOl = 48 rnA 0.35 0.5 V

C OPER = 0 Vee = 4.5 V, IOl = 20 rnA 0.25 0.5 0.25 0.5
»
en IOZH Vee
Vee
= 5.5
= 5.5
V,
V,
IOL = 2.7 V
Vo = 0.4 V
50
-50
50
-50
JlA
JlA
IOZl
(") II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 JlA
::D
(") IlL Vee = 5.5 V, VI = 0.4 V -2 -2 rnA
c lo~ -.Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
=i Vee = 5.5 V,
en lee
See Note 1
I Outputs low 127 175 127 175 rnA

NOTE 1: ICC is measured with all possible inputs grounded while achieving the stated output conditions.
1283
2-598 TEXAS
INSTRUMENTS
HEX 2-TO-1 UNIVERSAL MULTIPLEXERS

Vcc = 4.5 V. to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS857 SN74AS857
MIN MAX MIN MAX
A or B Y
tpd 2 15 2 12 ns
(COMP high) (Inverting)
A or B Y
tpd 2 12 2 10 ns
(COMP low) (Noninverting)
tpd 50 or 51 y 2 15 2 13
tpd COMP Y 2 15 2 13
ns
tpd A or B OPER = 0 2 16 2 14
tpd 50 to 51 OPER = 0 2 20 2 18
ten 2 14 2 12
50 to 51 Y ns
tdis 2 13 2 11
ten 2 14 2 12
COMP y ns
tdis 2 10 2 9
ten 2 14 2 12
50 OPER = 0 ns
tdis 2 10 2 9
ten 2 14 2 12
51 OPER = 0 ns
tdis 2 10 2 9
ten 2 10 2 13
COMP OPER = 0 ns
tdis 2 10 2 9
tpd =
ten =
tpLH or tpHL
tpZH or tpAL
en
tdis = tpHZ or tpLZ t::
NOTE 1: For load circuit and voltage waveforms. see page 1-12. :::>
C,.)
a:
C,.)
en
«
c
z
«
en
....I
«
1283
TEXAS 2-599
INsrRuMENTS
III
l>
r-
(J)
l>
:2
C
l>
(J)
Q/
;x,
(")
c
=i
(J)
2-600
8·BIT MAGNITUDE COMPARATORS
o Included among the Package Options Are SN54AS866 ... JD PACKAGE

28·Pin DIPs and Both Plastic and Ceramic SN74AS866 ... N PACKAGE
Chip Carriers (TOP VIEW)
o Input and Output Latches with Active·High QLE Vee

Enablos LlA eLRQ
P< Qin PLE
o Fast Compare to Zero P7
P>Qin
o Arithmetic and Logical Comparison Q7 P6
Q6 P5
o Open·Collector P = Q Output P4
Q5
o Dependable Texas Instruments Quality and Q4 P3
Reliability Q3 P2
Q2 P1
Q1 PO
QO P<Qout
P=Qout P>Qout
GND OLE

(TOP VIEW)
a a ulg
~ ~I§ 0 ~d i
w
description 4 3 2 1 282726
Q7 P7
These Advanced Schottky devices are capable of
performing high-speed arithmetic or logical com-
Q6 P6 en
parisons on two 8-bit binary or two's complement
Q5
Q4
P5
P4
!::
words. Three fully decoded decisions about words P ::l
Q3 P3 (J
and Q are externally available at the outputs. These
devices are fully expandable to any word length by
Q2 P2 a:
Q1 11 P1 (J
connecting the totem pole P> Q and P < Q outputs of
12 1314151617 18
each stage to the P > Q and P < Q inputs of the next en
higher-order stage. The cascading paths are im-
plemented with only a two-gate-Ievel delay to reduce
«
overall comparison times for long words. The open-
c
2!
collector P = Q outputs may be wire-ANDed together.
Both input words P and Q plus all three outputs (P > Q, P < Q, and P = Q) are equipped with latches to provide the
«
designer with temporary data storage for avoiding race conditions. The enable circuitry is implemented with minimal
en
..J
delay tiines to enhance performance when the devices are cascaded for longer word lengths. Each latch is transparent
when the appropriate latch enable, PLE, QLE, or OLE is high.
«
The enable inputs PLE and QLE and data inputs P and Q utilize p-n-p input transistors to reduce the low-level input
current requirement to typically -0.25 mA, which minimizes loading effects.
The Q register may be cleared to zero for a fast comparison of the P word to zero.
The SN54AS866 is characterized for operation over the full military temperature range of' - 55 °e to 125 °e. The
SN74AS866 is characterized for operation from ooe to 70 oe.

1283
TEXAS 2-601
INSTRUMENTS
logic symbol
CaMP
(2)
M [lOGIC]
M [ARITH. 2$ COMP]
(26)l....t:::..
PlE
h
C1 ,J . .
(18)
PO 10 1-0 0
(19)
P1
(20)
P2
(21)
P3
(22) P
P4
(23)
P5
(24)
P6
(25)
P7 7
P>O
(4)
P<O (3)
OLE (151
<
C3
>
P>O,fi
P<O 3D
P=O 3D ~
(16)
(17)
(131
P>O
P<O
p=o
ClR 0
(27) ,.... R
OLE
(1)
(12)
.,
C2
....
00 20 1=0 0
(11)
Q1
(10)
02
(9)
03
IB 04
as
(81
(71
0
»
r-
06
Q7
(6)
(5)
7
en
»
:2 Pin numbers shown are for JD and N packages.
C
»
en
n
::a
n
c:
=i
en
1283
2·602 TEXAS
INSTRUMENTS
.
• "01-
,-c. - n'07
--
0o
P7
7.E.:!.... 10
p1
- PO
c-
PO
'OO
(24\
O-
PO
~
- ~P5'05 ,
r
-
(231
:-!2-. I--
;-
P5
.- (221
~
P4
>p;-
r-:-:::--
--- ----
..........
r-.
P3"03
I--
~
(21)
J_ ~ P2=Q2
r;,-
-
PJ
I--
(20) P2
~:::::=t ~~
- r-.
......, 10
P2
..-.
Pl=Ql
r--
'-- - (16)
.- -
r-
r--
1191 P1
-
(13)
Pl
- PO"QO
~ "'---
0-
(18) PO
Po
I - JI
I
-
.~r;;--
-111
~ (/)
151
---'---10 ~
I>F,- W !:::
r-
::>
u
-101 00
as Lbo-II a:
r-- u
~ 05
==D- (/)
r--
05 :::::=t
«
~
~
-
o.
a.
OJ
IY.l
=J .......... 4MSS'"
c
2
«
- (/)
..J
~
-
02
C!2
D-
«
(111
- 01
I>w,- r------- -- ::>-
r-- ~
- (12)
~
FD
Gl!
"--
QIN (4)
GIN (31
121 -" ARITH
L/A.
I-V lOGIC
1283
TEXAS 2-603
INSTRUMENTS
FUNCTION TABLE
DATA INPUTS INPUTS OUTPUTS

COMPARISON L/A
PO-P7, QO-Q7 P>Q P<Q P>Q P<Q P=Q
Logical H P>Q X X H L L
Logical H P<Q X X L H L
Logical H P=Q L L L L H
Logical H P=Q L H L H L
Logical H P=Q H L H L L
Logical H P=Q H H H H L
Arithmetic L PAGQ X X H L L
Arithmetic L QAG P X X L H L
Arithmetic L P=Q L L L L H
Arithmetic L P=Q L H L H L
Arithmetic L P=Q H L H L L
Arithmetic L P=Q H H H H L
AG = arithmetically greater than
Supply voltage, Vee " . . . . . . . . . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage, P = Q output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS866 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS866 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .' . . . . . . . . . . . . . . . . - 65 °e to 150 °e
SN54AS866 SN74AS866
PARAMETER UNIT
IOH High-level output current, all outputs except P = Q -2 -2 rnA
VOH High-level output voltage, P=Q output 5.5 5.5 V
tsu Setup time to PLE, OLE, OLEI 2 2
ns
th Hold time after PLE, OLE, OLEI 4 4
1283
2-604 TEXAS
INSJRUMENlS
8-BIT MAGNITUDE COMPARATORS
electrical characteristics over recommended operating free-air temperature range (unless othe~",!ise noted)
SN54AS866 SN74AS866
VIK Vce = 4.5 V, II = -18 rnA -1.2 -1.2 V
VOH P>Q,P<Q Vee = 4.5 V to 5.5 V, 10H = -2 rnA Vee- 2 Vee- 2
10H P = Q only Vec = 4.5 V, VOH = 5.5 V 250 250 JlA
VOL Vee = 4.5 V, 10L = 20 rnA 0.35 0.5 0.35 0.5 V
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
L/A, OLE 40 40
IIH Vce = 5.5 V, VI = 2.7 V JlA
Others 20 20
L/A, OLE,
P> Qin, -4 -4
IlL P < Qin Vee = 5.5 V, VI = 0.4 V rnA
eLRQ -2 -2
P, Q, PLE, QLE -0.25 -1 -0.25 -1
lot Vee = 5.5 V, Vo = 2.25 V -20 -112 -20 -112 rnA
ICC Vee = 5.5 V, See Note 1 160 240 160 240 rnA

tThe output conditions have been chosen to produce' a current that closely approximates one-half of the true short-circuit, lOS'
NOTE 1: lee is measured with all inputs high except L/A, which is low.

Vcc = 4 .. 5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 n.
PARAMETER UNIT
SN54AS866 SN74AS866
tpLH 1 8.5 14 1 8.5 13
UA 1 14 1
ns
tpHL 7.5 7.5 13
tpLH P < Q, 1 5 10 1 5 8
ns
tpLH P>Q P < Q. 1 5.5 10 1 5.5 8
tpHL Any P or Q P>Q 1 13.5 21 1 13.5 17.5
ns
tpHL Data Input 1 10 17 1 10 15
tpLH 1 16 21 1 16 20
CLRQ ns
tpHL 1 12 17 1 12 16
Vcc = 4.5 V to 5.5 V.

CL = 5.0 pF.
FROM TO TA = 280 n.
PARAMETER UNIT
SN54AS866 SN74AS866
MIN TYpt MAX MIN TYpt MAX
tpLH P < Q, 1 6.5 12 1 6.5 11
P=Q ns
tpHL P>Q 1 8 14 1 8 13
tPLH Any P orQ 1 10 15 1 10 14
P=Q ns l
tpHL Data Input 1 9 14 1 9 13
tpLH 1 12 17 1 12 16
CLRQ P=Q ns
tpHL 1 13 18 1 13 17
t All typical vallues ree at Vee = 5 V, TA = 25°e.

1283
TEXAS 2-605
INSTRUMENTS
This sequence of comparisons illustrates how the CLRQ function can be used to perform dual comparisons of the varying P
terms (PO, P1, etc). When CLRQ is high, the P term is compared to the Q term. When CLRQ is taken low, the P term is com-
pared to zero. This or similar sequences can enhance performance and reduce package count to perform value range checks.
'AS866
l/A
PlE=H
QlE ~~_____________________________
P>Q P>Q
P<Q P<Q
QlE P=Q
ClRQ
QlE
!PO:QO i i P1:QO i P2:QO:
PO:ZERO P1:ZERO
lEI
l>
r-
en
7
l>
:2
C FIGURE 1-MAGNITUDE COMPARISONS COMBINED WITH QUICK COMPARISONS TO ZERO (RANGE VERIFICATIONS)
l>
en
(")
:tI
(")
c
=i
en
1283
2-606 TEXAS
IN STRUMENlS
SYNCHRONOUS 8-~IT UP/DOWN COUNTERS
D2661, DEC-EMBER 1982-REVISED DECEMBER 1983
o Included among the Package Options are SN54AS867, SN54AS869 ••• , JT PACKAGE
SN74AS867, SN74AS869 •••• NT PACKAGE
Compact, 24-Pin, 300-mil-Wide Dips and
(TOP VIEW)
28-Pin Ceramic Chip Carriers
o Fully Programmable with Synchronous so VCC
S1 ENP
Counting and Loading
A OA
o 'AS867 Has Asynchronous Clear, 'AS869 S Os
Has Synchronous Clear C Oc
D OD
o Fully Independent Clock circuit Simplifies Use
E OE
o Ripple Carry Output for n-Bit Cascading F OF
G OG
o Improved Performance Compared to
H OH
Schottky TTL:
ENT ClK
Typical Power Reduced by 38%
GND RCO
Maximum Count Frequency is 25% Higher
o Dependable Texas Instruments Quality and SN54AS867, SN54AS869 •••• FH PACKAGE
Reliability (TOP VIEW)
... 0 u ~I~ 4:
4:cncnz>wd
4 3 2 1 282726
S Os
C Oc
D OD
NC NC
E OE
F OF
G OG en
12 131415161718
~
:::>
:::c It-~GZ~dd
010 :::c
U ::£
u
a:
U
description en
These synchronous presettable counters feature an internal carry look-ahead for cascading in high-speed counting <t
applications. SynChronous operation is provided by having all flip-flops clocked simultaneously so that the outputs o
change coincident with each other when so instructed by the count-enable inputs and internal gating. This mode of 2
operation helps eliminate the output counting spikes that are normally associated with asynchronous (ripple-clock) <t
counters. A buffered clock input triggers the eight flip-flops on the rising (positive-going) edge of the clock waveform.
en
...J
These counters are fully programmable; that is, the outputs may each be preset to either level. The load mode circuitry
allows parallel loading of the cascaded counters. As loading is synchronous, selecting the load mode disables the <t
counter and causes the outputs to agree with the data inputs after the next clock pulse.
The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without additional
gating. Instrumental in accomplishing this function are two count-enable inputs and a carry output. Soth count enable
inputs (ENP and ENT) must be low to count. The direction of the count is determined by the levels of the select inputs
(see Function Table). Input ENT is fed forward to enable the carry output. The ripple carry output thus enabled will
produce a low-level pulse while the count is zero (all outputs low) counting down or 255 counting up (all outputs
high). This low-level overflow carry pulse can be used to enable successive cascaded stages. Transitions at the enable
ENP and ENT inputs are allowed regardless of the level of the clock input. All inputs are diode-clamped to minimize
transmission-line effects, thereby simplifying system design.

983
TEXAS 2-607
INSfRUMENlS
POST OFFICE BOX 225012 • DALLAS, TEXAS '75265
SYNCHRONOUS 8-BIT UP/DOWN COUNTERS
These counters feature a fully independent clock circuit. With the exception of thee asynchronous clear on the' AS867,
changes at control inputs (SO, S1) that will modify the operating mode have no effect on the Q outputs until clocking
occurs. Anytime the ENP and/or ENT is taken high, ReO will either go or remain high. The function of the counter
(whether enabled, disabled, loading, or counting) will be dictated solely by the conditions meeting the stable setup
and hold times.
The SN54AS867 and SN54AS869 are characterized for operation over the full military temperature range of _55°C to
125°C. The SN74AS867 and SN74AS869 are characterized for operation from oOe to 70°C.
logic symbols
'AS867 'AS869
so (1)
Sl (2)
.....;.;.~-J>C6/1 ,4,5-/3,4,5+ .....;.;.~-J>C6/1 ,4,5-13,4,5+
A (3)
A
..
B B (4)
C C (5)
D D (6)
E
F
G G
l> H H
r-
C/)
l> Pin numbers shown are for JT and NT packages.
2 FUNCTION TABLE
C Sl SO FUNCTION
l> L L Clear
C/) L H Count down
-
(") H L Load
H H Count up
:lJ
(")
c
=i absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
en Supply voltage, Vee .............. '................................................... 7 V
Input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Operating free-air temperature: SN54AS867, SN54AS869 ......................... - 55 DC to 125°C
SN74AS867, SN74AS869 ............................ , ODe to 70 De
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 DC to 150°C
483 '
2-608 TEXAS
INSTRUMENTS
SYNCHRONOUS 8·BIT UP/DOWN COUNTERS
A (3)
(5)
c
flII
CJ)
!::
(6) ~'
0
U
CC
U
CJ)
(7)
E cd:
0
Z
<t
(8) CJ)
F ..J
<t
(9)
G
(10)
H--~~H
483
TEXAS 2-609
INSTRUMENTS
TYPES SN54AS867, SN74AS867,
SYNCHRONOUS 8·BIT UP/DOWN COUNTERS WITH ASYNCHRONOUS CLEAR

SN54AS867 SN74AS867
UNIT
tw(clock) Duration 12.5 10 ns
tw(clear) Duration of clear pulse (SO and S1 low) 12.5 10 ns
Data inputs A-H 5 4 ns
Enable P (ENP)or
9 8 ns
Enable T (ENT)
tsu Setup time t SO or S 1 (load) 11 10 ns
SO or S1 (clear) 11 10 ns
SO or S1 (count down) 42 40 ns
SO or S1 (count up) 42 40 ns
th Hold time at any input with respect to clockt 0 0 ns
Skew time between SO and S1 (maximum to
tskew 8 7 ns
avo~ ~advertentc~a~
tThis setup time is required to ensure stable data.
» electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
CJ) PARAMETER TEST CONDITIONS UNIT
Typt Typt MAX
»
2
VIK Vee = 4.5 V. 'I = 18 mA
MIN MAX
-1.2
MIN
-1.2 V
VOH Vee = 4.5 V to 5.5 V. 10H = -2 mA Vce- 2 Vee- 2 V
C VOL Vee = 4.5 V. IOL = 20 mA 0.34 0.5 0.34 0.5 V
»CJ) II
ENT
Vee = 5.5 V. V, = 7 V 0.1
40
0.1
40
mA
IIH Vee = 5.5 V. V, = 2.7 V pA

Other inputs 20 20
(')
ENT -4 -4
Vee = 5.5 V. VI = 0.4 V mA
:JJ IlL
Other inputs -2 -2
(") -30 -112 -30 -112 mA
lo§ Vee = 5.5 V. Va = 2.25 V
c ICC Vee = 5.5 V 134 195 134 195 mA
=t
en tAli typical values are at Vee = 5 V. TA = 25°e.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS'
983
2-610 TEXAS
INSTRUMENTS
SYNCHRONOUS 8·BIT UP/DOWN COUNTERS WITH SYNCHRONOUS CLEAR
SN54AS869 SN74AS869
UNIT
tw(clock) Duration 12.5 11 ns
Data inputs A-H 6 5 ns
Enable P (8#') or
10 9 ns
Enable T (ENT)
tsu Setup time t SO or 51 (load) 13 11 ns
SO or 51 (clear) 13 11 ns
SO or 51 (count down) 52 50 ns
SO or 51 (count up) 52 50 ns
th Hold time at any input with respect to clockl 0 0 ns
TA Operating free-air temperature -55 125 0 .70 °e
tThis setup time is required to ensure stable data.
SN54AS869 SN74AS869
MIN TVpt MAX MIN TVPt MAX
VIK Vee = 4.5 V, II = 18 mA -1.2 -1.2 V en
VOH Vee = 4.5 V to 5.5 V, IOH = -2 mA vee- 2 Vee- 2 V t:
VOL Vee = 4.5 V, IOL = 20 mA 0.34 0.5 0.34 0.5 V ::J
II Vee = 5.5 V, VI =7V 0.1 0.1 mA U
ENT 40 40 a:
IIH Vee = 5.5 V, VI = 2.7 V JlA
Other inputs 20 20 U
ENT -4 -4
IlL Vee = 5.5 V, VI = 0.4 V mA en
lo§
Other inputs
Vee = 5.5 V, Vo = 2.25 V -30
-2
-112 -30
-2
-112 mA
«
ICC Vee = 5.5 V 125 180 125 180 mA c
2
~ All typical values are at Vee ~ 5 V, T A = 25°e.
«
en
...J
«
983
TEXAS 2-611
INSfRUMENTS
SYNCHRONOUS 8·BIT UP/DOWN COUNTERS

Vec = 4.5 V to 5.5 V
CL = 50 pF.
FROM TO RL = 500 n
PARAMETER UNIT
SN54AS867 SN74AS867
MIN MAX MIN MAX
f max 40 50 MHz
tplH 5 31 5 22
ClK RCO ns
tpHl 6 19 6 16
tplH 3 12 3 11
ClK Any Q ns
tPHl 4 16 4 15
tplH 3 19 3 10
ENT RCO ns
tPHl 5 21 5 17
tplH 5 14 5 14
ENP RCO ns
tpHl 5 21 5 17
Clear
tpHl Any Q 7 23 7 21 ns
(50,51 low)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
= 500 n
III PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
Rl
TA = MIN to MAX
SN54AS869 SN74AS869
UNIT
l> MIN MAX MIN MAX

r- f max 40 45 MHz
en tPlH 6 35 6 35
ClK RCO ns
l> tpHl 6 20 6 18
2: tplH
ClK Any Q
3 12 3 11
ns
C tpHl 4 16 4 15
3 25 3 15
l> tplH
ENT RCO ns
en tpHl 6
5
21
27
6
5
17
19
tPlH ns
(") ENP RCO
6 21 6 18
tpHl
'$
(")
c NOTE 1: For load circuit and voltage waveforms. see page 1-12.
=f
en
983
2-612 TEXAS
INSTRUMENTS
DUAL 16·BY·4 REGISTER FILES
o ' AS870 in Compact 24-Pin, 300-mil DIP and SN54AS870 _ ... JT PACKAGE
SN74AS870 . ... NT PACKAGE
Both Plastic and Ceramic 28-Pin Chip Carriers
(TOP VIEW)
• ' AS871 in 28-Pin 600-mil DIP and Both SO 1 24 VCC
Plastic and Ceramic Chip Carriers lAO 2 23 51
lAl 22 2A3
• 3-State Buffer-Type Outputs Drive Bus lA2 21 2A2
lA3 20 2Al
Lines Directly fw 19 2AO
52 18 2W
• Typical Access Time Is 11 ns DQAl 17 53
DQA2 9 16 DQB4
• Each Register File Has Individual Write OQA3 10 15 OQB3
Enable Controls and Address Lines OQA4 11 14 OQB2
GND 12 13 DQBl
• Designed Specifically for Multibus
Architecture and Overlapping File SN54AS871 .... JD PACKAGE
SN74AS871 .... N PACKAGE
Operations
(TOP VIEW)
• Prioritized B I nput Port Prevents Write OAl VCC
Conflicts During Dual Input Mode DA4
DA3
• Dependable Texas Instruments Quality lAO 4 25 51
lAl 24 2A3
and Reliability
lA2 6 23 2A2
lA3 22 2Al
description fw 21 2AO
52 9 2~ 2W
These devices feature two 16-word by 4-bit register files_ Each QAl 10 19 53
register file has individual write-enable controls and address lines_ QA2 11 18 DOB4
QA3 12 17 DOB3
The 'AS870 has two 4-bit data I/O ports (00A1-00A4 and QA4 13 16 DOB2
OOB1-00B4L The 'AS871 has one 4-bit data I/O port (00B1- GND 14 15 DOBl
OOB4) with the other data port having individual data inputs
SN54AS870 . .. _ FH PACKAGE
(OA 1-0A4) and data outputs (OA 1-0A4). The data I/O ports can
output to Bus A and Bus B, receive input from Bus A and Bus B,
SN74AS870 .... FN PACKAGE
en
receive input from Bus A and output to Bus B, or output to Bus -
(TOP VIEW)
0 U M
t:
A and receive input from Bus B_ To prevent writing conflicts in
« «
--VlZ>(/)N
0 U u~ « ::>
the dual-input mode, the B input port takes priority_ Two select 4 3 2 1 78 2726 ua:
1 A2 5 25 2A2
lines, SO and S1, control which port has access to which register.
lA3 6 2Al
S2 determines whether the A ports are in the input or the output 1'W 2AO U
modes and S3 does Iikewise for the B ports_ The address lines NC
52
NC
2W
en
(IAO-IA3 or 2AO-2A3) are decoded by an internal 1-of-16 de-
coder to select which register word is to be accessed_ All outputs
OOAl
9
10 S3 <t
OOA2 11 DOB4
are 3-state buffer-type outputs designed specifically to drive bus 12 1314151617 18
C
lines directly_ M-.:tOU-NM z
«<czzmm m
00l:)
00
000
000
<t
The SN54AS870 and.SN54AS871 are characterized for operation SN54AS871 _... FH PACKAGE en
..oJ
over the full military temperature range of -55°e to 125°e. The SN74AS871 .... FN PACKAGE
SN74AS870 and SN74AS871 are characterized for operation (TOP VIEW) <t
o o N~ U<tM
from oOe to 70 e. « a <c <c u<c <c
~UlOO>OO
4 J 2 1 28 2726
Sl
2A3
2A2
12 1314 15161718
Moo:tO_NM-.::t
~~~gggg
TEXAS 2-613
INSTRUMENTS
logic symbols
'AS870 'AS871
[REG FILE 16 X 4) (REG FILE 16 X 4)
j..J\
j
l
2A.!!..
COfGl0
15
(151
RAM 16X 1 RAM16Xl Z7 DOBl
[REG 1) (REG1)
MUX MUX
6 lA,lf,2(1f!l'14D 6 lA,ll,2(lfll4D 13[>\7
7 lA.1,l,4D lA Z8 7 lA.1,3,4D lA Z8
8 Ti 8 IT
RAM 16X 1 RAM 16X 1
(REG 2) (REG2)
9 11 9 11
6 2A,O,2(lf315D 6 2A,O.2(lf3)SD
7 2A,l,l,SD 2A Z9 7 2A.l.3.SD 2A Z9
t - -.......- .......- - - -.......- .......- - l l ... ,~ 1111,41 0082 DA2
(151 DOBl CA2
1161 0084 DA3
CA3
DA4
CA4
Pin numbers shown are for JD, JT, N, and NT packages,
1283
2-614 TEXAS
INSTRUMENTS
FUNCTION TABLE
FILE SELECT INPUT/OUTPUT

SO S1 FILE SEL S2 S3 I/O SEL
L L 1R TO A. 1 R TO B L L A OUT. BOUT
H L 2R TO A. 1 R TO B
L H 1RTOA.2RTOB
H H 2R TO A. 2R TO B
L L A TO 1 R. 1 R TO B H L A IN. BOUT
H L A TO 2R. 1 R TO B
L H A TO 1 R. 2R TO B
H H A TO 2R. 2R TO B
L L 1 R TO A. B TO 1 R L H A OUT. BIN
H L 2R TO A. B TO 1 R
L H 1 R TO A. B TO 2R
H H 2R TO A. B TO 2R
L L B TO 1R H H AIN. BIN
H L A TO 2R. B TO 1 R
L H A TO 1 R. B TO 2R
H H BTO 2R
absolute maximum ratings over operating free· air temperature range (unless otherwise noted)
Input voltage: All inputs . . . . . . . . . . . . ' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • 5.5 V
Operating free-air temperature range: SN54AS870. SN54AS871 . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS870.SN74AS871 . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 6 5 °e to 1 50 °e en
t:
recommended operating conditions ::>
u
SN54AS870
SN54AS871
SN74AS870
SN74AS871 UNIT
a::
MIN NOM MAX MIN NOM MAX u
Vee Supply voltage 4.5 5 5.5 4.5 5 5.5 V en
VIH High-level input voltage 2 2 V <t
Low-level input voltage 0.8 0.8 V
VIL C
High-level output current -12 -15 mA
IOH Z
ns
<t
tw Duration of write pulse 12 12
Address before write.\. 5 5 en
...J
Setup times Data before write t 15 15 ns
tsu
Select before write.\. 12 12
<t
Address after write t 0 0
th Hold times Data after writet 0 0 ns
Select after write t 12 12
1283
TEXAS 2-615
INSTRUMENTS
,AS870 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54AS870 SN74AS870
V,K Vee = 4.5 V, " = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V, IOH = -12 rnA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 rnA 2.4 3.2
Vee - 4.5 V, IOl - 32 rnA 0.25 0.5
VOL V
Vee = 4.5 V, IOl = 48 rnA 0.35 0.5
Control inputs Vee = 5.5 V, V, = 7 V 0.1 0.1
rnA
DOA and DaB ports Vee = 5.5 V, V, = 5.5 V 0.2 0.2
"
Wl and W2 20 20
"H Other control inputs Vee = 5.5 V, V, = 2.7 V 40 40 p.A
DOA and DaB ports:t 50 50
Control inputs -2 -2
"l Vee = 5.5 V, V, = 0.4 V rnA
DOA and DaB ports:!: -2 -2
lo§ Vee = 5.5 V, Vo = 2.25 V -30 ..:112 -30 -112 rnA
ICC Vee = 5.5 V 120 190 120 190 rnA
,AS871 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
SN54AS871 SN74AS871
V,K Vee = 4.5 V, " = -18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 rnA VCC-2 Vce- 2
ItJ VOH Vee

Vee
Vee
= 4.5 V,
= 4.5 V,
= 4.5 V,
IOH = -12 rnA
IOH = -15 rnA
IOl = 32 rnA
2.4 3.2
0.25 0.5
2.4 3.2
V
~ VOL
= 4.5 V, IOl = 48 rnA
V
.r- Vee 0.35 0.5
CJ) IOZH OA outputs Vae = 5.5 V, Vo = 2.7 V 50 50 p.A
IOZl OA outputs Vee = 5.5 V, Vo = 0.4 V -50 -50 p.A
~ Control and DA inputs Vee = 5.5 V, V, = 7 V 0.1 0.1
Z DaB ports Vee = 5.5 V, V, = 5.5 V 0.2 0.2
rnA
"
C Wl, W2 and DA inputs 20 20
~ Other control
p.A
CJ) "H 40 40
inputs Vee = 5.5 V, V, = 2.7 V
DaB ports:!: 50 50
Q Control and DA inputs -2 -2
l:J ',l Vee = 5.5 V. V, = 0.4 V rnA
DaB ports:!: -2 -2
(')
c: IO§ Vee
Vee
=
=
5.5 V,
5.5 V
Vo = 2.25 V -30
120
-112
190
-30
120
-112
190
rnA
rnA
~
ICC
en tAli typical values are at Vee = 5 V. TA = 25°C.

iFor I/O ports, the parameters IIH and III include the output currents IIOZ and 10Zl' respectively.
§The output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit current, lOS.
1283
2-616 TEXAS
INSTRUMENTS

Vcc - 4.5 V to 5.5 V.
FROM TO CL = 50 pF.
PARAMETER UNIT
(INPUT) (OUTPUT) RL = 500 fl.
TA = MIN to MAX
SN54AS870 SN74AS870
MIN MAX MIN MAX
talA) Any A Any DO 5 20 5 15 ns
50 Any DOA 3 15 3 13
t a(5) ns
51 Any DaB 3 15 3 13
52 Any DOA 3 12 3 11
tdis ns
53 Any DaB 3 12 3 11
52 Any DOA 3 15 3 12
ten ns
53 Any DaB 3 15 3 12
W Any DO 5 23 5 19
tpd DOA DaB 5 25 5 22 ns
DaB OOA 5 25 5 22

Vcc = 4.5 V to 5.5 V.
FROM TO CL = 50 pF.
PARAMETER UNIT.
(INPUT) (OUTPUT) RL = 500 O.
TA = MIN to MAX
SN54AS871 SN74AS871
MIN MAX MIN MAX
talA) Any A Any OA or DaB 5 20 5 16 ns
en
50 Any OA 3 15 3 13 t::
t a(5)
51 Any DaB 3 15 3 13
ns ::>
52 Any OA
(J
3 12 3 11
tdis
53 Any DaB 3 12 3 11
ns a:
52 Any OA 3 15 3 12 (J
ten ns
53 Any DaB 3 15 3 12 en
tpd
W
DA
Any OA or DaB
DaB
5
5
23
26
5
5
19
23 ns
«
DaB OA 5 26 5 23 o
z
NOTE 1: For load circuit ~nd voltage waveforms, see page 1-12.
«
en
~
«
1283
TEXAS 2-617
INSTRUMENTS
IIItJ
l>
r-
t/)
l>
:2
C
l>
t/)
Q
:D
(")
c
=i
t/)
2-618
DUAL 4·BIT D·TYPE LATCHES WITH 3·STATE OUTPUTS
• 3·State Buffer·Type Outputs Drive Bus·Lines Directly SN54ALS873. SN54AS873 . JT PACKAGE

SN74AlS873.SN74AS873. NT PACKAGE
• Bus·Structured Pinout
(TOP VIEW)
• ' ALSaaO and' ASaaO Are Alternative Versions with
Inverting Outputs 1ClR VCC
10C 1C
• Package Options Include Both Plastic and Coramic 101 101
Chip Carriers in Addition to Plastic and Ceramic DIPs 102 102
• Dependable Texas Instruments Quality and Reliability 103 103
104 104
description 201 201
202 202
These dual 4-bit registers feature three-state, outputs designed 203 203
specifically for bus driving. This makes these devices particularly 204 204
suitable for implementing buffer registers. 1/0 ports. bidirectional 20C 2C
bus drivers. and working registers. GNO 2ClR
~----
The dual 4-bit latches are transparent O-type. While the latch
enable input (1 C or 2C) is high. tne 0 outputs will follow the data
(0) inputs in true form. according to the function table. When the
SN54ALS873. SN54AS873 . , FH PACKAGE
latch enable input is taken low. the outputs will be latched. When
SN74ALS873. SN74AS873. FN PACKAGE
ClR goes low. the 0 outputs go low independently of enable C.
(TOP VIEW)
The outputs are in a high-impedance state when OC (output
control) is at a high logic level. ... IU
oouu 15 u ...
uuo
The SN54AlS873 and SN54AS873 are characterized for
......... z> ......
operation over the full military temperature range of - 55 cc to 4 3 2 1 282726
125 cc. The SN74AlS873 and SN74AS873 are characterized 102 102
for operation from ooC to 70 cc. 103 103
104 104 en
NC NC t:
201 201 ::>
FUNCTION TABLE (EACH LATCH) 202
203
202
203
ua:
INPUTS OUTPUT
12 131415161718
OC CLR ENABLE C 0 Q
U
L
L
L
H
X
H H
X
H
L
.q IU UIa: U
0
oozzcjC'lO
.q
en
L H H L L
C'lC'l(!) C'l C'l <t
L H L X 00 NC - No internal connection
C
H X X X Z 2
<t
en
...J
<t

1283
TEXAS 2-619
INSTRUMENTS
DUAL 4·81T D·TYPE LATCHES WITH 3·STATE OUTPUTS
logic symbol
201
202
203
204
functional block diagram (each quad latch, positive logic)
~------~1I
..
I
c--~
01 ----+-+--1
01
02
02 -----+--+--1
03
03 -----+--+~
04
04 --------1
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS873, SN54AS873 . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS873,SN74AS873 . . . . . . . . . . . . . . . . . . . . . . . OOet070oe
Storage temperature range ....... '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " - 65 °e to 150 °e
1283
2-620 TEXAS
INSTRUMENTS
POST,OFFICE BOX 225012 • DALLAS, TEXAS 75265
DUAL 4·BIT O·TYPE LATCHES WITH 3·STATE OUTPUTS

UNIT
IOL low-level output current 12 24 rnA
Pulse duration
I eLR low 15 15
ns
tw
I Enable e high 10 10
tsu Setup time, data before enable e~ 10 10 ns
th Hold time, data after enable e.J. 7 7 ns
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V, 10l = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V 10L = 24 rnA 0.35 0.5
10ZH Vee = 5.5 V, Va = 2.7 V 20 20 p.A
10Zl Vee = 5.5 V, Va = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA en
10* Vee = 5.5 V, Va = 2.25 V -15 -70 -15 -70 rnA !::
::>
= 5.5
u
lee Vee V Outputs low
Outputs disabled
15
16
29
31
15
16
29
31
rnA
a:
j
tAli tYPical values are at Vee = 5 V, TA = 25°e. u

~The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS' en
«
c
z
«
en
...J
«
1283
TEXAS 2-621
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
FROM TO R1 = 500 Q,
PARAMETER UNIT
(INPUT) (OUTPUT) R2 = 500 Q,
TA = MIN to MAX.
MIN MAX MIN MAX
tpLH 2 15 2 14
D Q ns
tpHL 2 15 2 14
tpLH 8 29 8 22
C Q ns
tpHL 8 22 8 21
tpHL CLR Q 6 24 6 24 ns
tpZH 4 21 4 18
OC: Q ns
tpZL 4 21 4 18
tpHZ 2 10 2 8
OC: Q ns
tpLZ 2 15 2 13
NOTE1:·For load circuit and voltage waveforms, see page 1·12.
- »
r-
fA
»
2
D latch signal conventions
It is TI practice to name the outputs and other inputs of a Ootype latch and to draw its logic symbol based on the
assumption of true data (OJ inputs. Then outputs that produce data in phase with the data inputs are called Q and those
producing complementary data are called Q. An input that causes a Q output to go high or a 0 output to go low is called
Preset; an input that causes a Q output to go high or a Q output to go low is called Clear. Bars are used over these pin
names (PRE and CLRj if they are active low.
In some applications it may be advantageous to redesignate the data input D. In that case all the other inputs and
C outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
»
fA
(")
ii
(")
PRE S (5)
Q
ClR R (5)
Q
C C1 C C1
c 0 10 (6) [5 10 (6)
=i R Q S
Q
en ClR PRE
Notice that Q and a exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (1::::..) on PRE and CLR remain since these inputs are still active-low, but that the presence or absence of the
polarity indicator changes at D, Q, and O. Of course pin 5 (0) is still in phase with the data input D, but now both are
1283
2-622 TEXAS
INSTRUMENTS

SN54AS873 SN74AS873
UNIT
tw Pulse duration I elR low 4.5 3.5

ns
I Enable e high 5.5 4.5
tsu Setup time, data before enable e-l- 2 2 ns
th Hold time, data after enable e-l- 3 3 ns
SN54AS873 SN74AS873
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V, IOH = -2 mA vee- 2 vee- 2
VOH Vee = 4.5 V, IOH = -12 mA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 mA 2.4 3.3
Vee = 4.5 V, IOl = 32 mA 0.25 0.5
VOL V
Vee = 4.5 V, IOl = 48 mA 0.35 0.5
IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 /LA
IOZl Vee = 5.5 V, Vo = 0.4 V -50 -50 /LA
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 /LA
III Vee = 5.5 V, VI = 0.4 V -0.5 -0.5 mA
lot Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
Ice Vee = 5.5 V I Outputs low 67 109 67 109 mA
1283
TEXAS 2-623
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO R2 = 500 n.
PARAMETER UNIT
SN54AS873 SN74AS873
MIN MAX MIN MAX
tpLH 3 9 3 6
D Q ns
tpHL 3 7 3 6
tPLH 6 14 6 11.5
e Q ns
tPHL 4 9 4 7.5
tpHL eLR Q 3 8.5 3 7.5 ns
tpZH 2 8 2 6.5
De Q ns
tpZL 4 '11 4 9.5
tPHZ 2 8 2 6.5
De Q ns
tPLZ 2 8.5 2 7.5
1283
2-624 TEXAS
INSTRUMENTS
DUAL 4·81T D·TYPE EDGE·TRIGGERED FLlp·FLOPS
02661, APRIL 1982- REVISED DECEMBER1983
o 3·State Buffer-Type Outputs Drive Bus-Lines Directly SN54ALS874, SN54AS874 ..• JT PACKAGE
SN74ALS874. SN74AS874 .•• NT PACKAGE
o Bus-Structured Pinout (TOP VIEW)
o Choice of True or Inverting Logic VCC
lCLK
'ALS874, 'AS874 True Outputs 101
102 102
'ALS876, 'AS876 Inverting Outputs 103 103
104
• Asynchronous Clear 201 201
202 202
o Package Options Include Both Plastic and Ceramic 203 203
Chip Carriers in Addition to Plastic and Ceramic DIPs 204 10 15 204
20C 11 14 2CLK
• Dependable Texas Instruments Quality and Reliability GNO 12 13 2CLR
SN54ALS874. SN54AS874 ... FH PACKAGE
description SN74ALS874. SN74AS874 ... FN PACKAGE
(TOP VIEW)
These dual four-bit registers feature three-state outputs designed
couu u~-
-luiS
specifically for bus driving. This makes these devices particularly
---z>-_
4
uUo
3 2
bus drivers, and working registers. 102 102
103 103
The edge-triggered flip-flops enter data on the low-to-high transi- 104 104
tion of the clock. The' ALS874 and' AS874 have CLR inputs and NC NC
201 9 201
noninverting Q outputs; the' ALS876 and' AS876 have PRE 202 10 202
inputs and inverting IT outputs. In each case. taking this input 203 11 203
low causes the four Q or 0: outputs to go low independently of 12 1314 151617 18
the clock.
~I~ ~ ~ld d~ NN
The SN54ALS874, SN54AS874, SN54ALS876 and SN54ALS876.SN54AS876 ... JTPACKAGE

SN54AS876 are characterized for operation over the full military SN74ALS876. SN74AS876 ... NT PACKAGE
temperature range of - 55 °C to 125°C. The SN74ALS874, (TOP VIEW) en
SN74AS874, SN74ALS876, and SN74AS876 are character- 1 PRE
loe
24 vCC
lCLK
t:
101
23
101 :::>
102
22
21 102 u
103 20 103 a:
104
201
6
7
19
18
104
201 u
202 8 17 202
en
203
204
9
10
16
15
203
204 «
20e
GNO
11
12
14
13
2CLK
2PRE c
2:
SN54ALS876.SN54AS876 ... FHPACKA~E
SN74ALS876. SN74AS876 ... FN PACKAGE «
(TOP VIEW) en
-Iulw u~- ..J
---z>-_
co8:uuulO
4 3 2 1 282726
«
102 5 25 lQ2
103 6 24 103
104 23 lQ4
NC 22 NC
201 9 21 201
202 10 20 iQ2
203 11 19 2Q3
12131415161718
~Ig ~ ~I~
N.N l!)
dl~
N N N

1283
TEXAS 2-625
INSTRUMENTS
FUNCTION TABLES
'ALSB74, 'AS874 (EACH FLIP-FLOP) 'ALS876, 'AS876 (EACH FLIP-FLOP)

OC CLR CLK D Q DC PRE CLK D Q
L' L X X L L L X X L
L H t H H L H t H L
L H t L L L H t L H
L H L X QO. L H L X 00
H X X X Z H X X X Z
logic symbols
'ALS874, 'AS874 'ALS876, 'AS876
- l>
r-
C/)
l>
2
'ALS874, 'AS874 (EACH QUAD FLIP-FLOP)
OC-------<lI
'ALS876, 'AS876 (EACH QUAD FLIP-FLOP)
OC------------~
CLK-----1 CLK-----f
C
CLR
l>
C/)
Q 01 ----+--+--I 01 ----+-+-....
:2l
n
c: Q2
=t
en 02 ----+--+-... 02 ----+-+-....
03
03 ----+--+--I 03 ----+-+-1
04
04-------.. . . 04--------1
1283
2-626 TEXAS
INSTRUMENTS
DUAL 4·81T D·TYPE EDGE·TRIGGERD FLIp· FLOPS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS874, SN54ALS876 . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
Storage temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50 °e

tw Pulse duration ClK high 20 , 16.5 ns
ClK low 20 16.5
tsu ns
before ClKt PRE or ClR inactive 10 10
th
TA
Hold time, data after ClK t
Operating free-air temperature - 55
4
125
0
0 70
ns
°e I.'~I,~.,,::~~:~J
electrical characteristics over recommended operating free· air temperature range (unless otherwise noted)
en
!::
SN54ALS874 SN74AlS874 ::>
PARAMETER TEST CONDITIONS SN54AlS876 SN74AlS876 UNIT C,.)
MIN Typt MAX MIN Typt MAX a:
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V C,.)
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA vee- 2 vee- 2
Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
en
VOH
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
<t
Vee = 4.5 V, IOl = 12 mA 0.25 0.4 0.25 0.4
V
C
Val
VCC = 4.5 V, IOl = 24 mA 0.35 0.5 2
10ZH Vee = 5.5 V, Va = 2.7 V 20 20 p.A <t
10Zl Vce - 5.5 V,
Vce - 5.5 V,
Vo - 0.4 V
VI - 7 V
-20
0.1
-20
0.1
p.A
mA
en
-I
II
IIH Vce - 5.5 V, VI - 2.7 V 20 20 p.A <t
III Vce = 5.5 V, VI = 0.4 V -0.2 -0.2 mA
lot Vce = 5.5 V, Va = 2.25 V -15 -70 -15 -70 mA
1 Outputs high 14 21 14 21
lee Vce = 5.5 V 1 Outputs low 18 29 18 29 mA
.1 Outputs disabled 20 31 20 31
~The output conditions have been chosen to produce a current that closely approximates one half of the true short· circuit output current. lOS'
1283
TEXAS 2-627
INSTRUMENlS
Vcc = 4.5 V to 5.5 V,

CL = 50 pF,
FROM TO
R1 = 500 Q,
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 Q, UNIT
TA = MIN to MAX
MIN MAX MIN MAX
f max 25 30 MHz
tpLH 4 15 4 14
CLK Any Q ns
tpHL 4 15 4 14
tpZH 4 21 4 18
5C Any Q ns
tpZL 4 21 4 18
tpHZ 2 10 2 8
DC AnyQ ns
tPLZ 3 15 3 13
..
Vec = 4.5 V to 5.5 V,
CL = 50 pF,
FROM
R1 = 500 Q,
TO
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 Q, UNIT
TA = MIN to MAX
l> MIN MAX MIN MAX
r- f max 25 30 MHz
en tpLH 4 15 4 14
CLK Any Q ns
l> tPHL 4 15 4 14
2 tpHL PRE Any Q 6 22 6 19 ns
o tpZH
OC Any Q
4 21 4 18
ns
tpZL 4 21 4 18
l> tpHZ 2 10 2 8
en tpLZ
DC Any Q
3 15 3 13
ns
~ NOTE 1: For load circuit and voltage waveforms, see page 1·12.
~
o
c
~
en
1283
2-628 TEXAS
INSTRUMENTS
TYPES SN54ASB74, SN54ASB76, SN74ASB74, SN74ASB76
DUAL 4·BIT D·TYPE EDGE·TRIGGERED FLlP·FLOPS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ASB74, SN54ASB76 . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ASB74,SN74ASB76 . . . . . . . . . . . . . . . . . . . . . . . . . QOCto7Qoe
Storage temperature range

SN54AS874 SN74AS874
fclock elock frequency a 100 a 125 MHz
PRE or elR low 3 2
tw Pulse duration elK high 4 3 ns
elK low 5 4
Setup time Data 2.5 2
tsu ns
before elK t PRE or elR inactive 5 4
th Hold time, data after elKt 1 1 ns
TA Operating free-air temperature -55 125 a '70 °e
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) C/)
SN54AS874 SN74AS874 !::
PARAMETER TEST CONDITIONS SN54AS876 SN74AS876 UNIT :l
MIN Typt MAX MIN Typt MAX U
VIK Vee = 4.5 V, II = -18'mA -1.2 -1.2 V
a:
Vee = 4.5 V to 5.5 V, IOH = -2 rnA Vee- 2 Vee- 2 U
VOH Vee = 4.5 V, IOH = -12 rnA 2.4 3.2 V C/)
Vee
Vee
=
=
4.5 V,
4.5 V,
IOH = -15 rnA
10l = 32 rnA 0.25 0.5
2.4 3.3 «
VOL
vee;' 4.5 V, 10l = 48 rnA 0.35 0.5
V o
'2
IOZH
10Zl
Vee
Vee
=
=
5.5 V,
5.5 V,
Va = 2.7 V
Va = 0.4 V
50
-50 -50
50 ~A
~A
«
II Vee = 5.5 V, VI = 7 V 0.1 0.1 rnA C/)
= VI = 2.7 V ...J
IIH
III
D
Vee
Vee =
5.5 V,
5.5 V, VI = 0.4 V
20
-3
20
-2
~A
rnA
«
All other -0.5 -0.5
10:1: Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
'AS874 Outputs low 92 149 92 149
lee Vee = 5.5 V rnA
'AS876 Outputs low 94 150 94 150
t All typical values are at Vee; 5 V, TA ; 25°e.
:t:The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'
1283
TEXAS 2-629
INSTRUMENTS
DUAL 4·BIT D·TYPE EDGE·TRIGGERED FLlp·FLOPS
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
Rl = 500 n.
PARAMETER
SN54AS874 SN74AS874
MIN MAX MIN MAX
f max 100 125 MHz
tpLH 3 11.5 3 8.5
CLK Any Q ns
tpHL 4 12.5 4 10.5
tpHL CLR Any Q 4 11 4 9.5 ns
tpZH 2 8 2 7
OC Any Q ns
tpZL 3 11.5 3 10.5
tpHZ 2 7 2 6
6C Any Q ns
tpLZ 2 8.5 2 7.5
Vcc = 4.5 V to 5.5 V.

CL = 50 pF.
Rl = 500 n.
PARAMETER
FROM TO R2 = 500 n.
UNIT
SN54AS876 SN74AS876
~
MIN MAX MIN MAX
f max 100 125 MHz
tpLH 3 11.5 3 8.5
»
r-
tpHL
CLK Any Q
4 12.5 4 10.5
ns
tpHL PRE Any Q 4 11 4 9.5 ns

CA
tpZH 2 8 2 7
»
2
tpZL
OC Any Q
3
2
11.5
7
3
2
10.5
6
ns
tPHZ
OC Any Q ns
C tPLZ 2 7 2 6
»
CA
C')
:JJ
C')
c
=i
CA
1283
2-630 TEXAS
INSTRUMENTS
• Included among the Package Options Are Com· SN54AS877 •••• JT PACKAGE
pact, 24-Pin, 300-mil-Wide Dips and Both 28- SN74AS877 •••• NT PACKAGE
(TOP VIEW)
Pin Plastic and Ceramic Chip Carriers
• Buffered 3-State Outputs Drive Bus Lines
so VCC
S1 CLK
Directly
S2 SERIN
• Cascadable to n-Bits A1 81
A2 82
• Eight Selectable Transceiver/Port Functions:
A3 83
- A to B or B to A A4 84
- Register to A or Register to B A5 85
- Shifted to A or Shifted to B A6 86
- Off-Line Shifts (A and B Ports in High- A7 87
Impedance State) A8 88
- Register Clear GND-...._ _...r- 08
• Particularly Suitable for Use in Signature-
Analysis Circuitry SN54AS877 •••• FH PACKAGE
SN74AS877 •••• FN PACKAGE
• Serial Register Provides:
(TOP VIEW)
- Parallel Storage of Either A or B Input Data
- Serial Transmission of Data from Either
A or B Port
4 3 2 1 282726
o Dependable Texas Instruments Quality and B1
Reliability B2
B3
NC
B4
B5
en
B6 !::
=>
121314151617 18
u
a:
u
NC - No internal connection,
en
description <t
The' AS877 features two 8-bit I/O ports (A 1-A8 and 81-88), an 8-bit parallel-load, serial-in, parallel-out shift register, C
and control logic_ With these features, this device is capable of performing eight selectable transceiver or port functions, Z
depending on the state of the three select lines SO, 51, and S2. These functions include: transferring data,from port A to <t
port 8 or vice versa (i.e., the transceiver function)! transferring data from the register to either port, serial shifting data en
..J
to either port, performing off-line shifts (with A and 8 ports in high-impedance state), and clearing the register. Syn-
chronous parallel loading of the internal register can be accomplished from either port on the positive transition of the <t
clock while serially shifting data in via the SERIN input. The 'AS877 is ideally suited for applications needing signature-
analysis circuitry to enhance system verification and/or fault analysis. All serial data, is shifted right. All outputs are
buffer-type outputs designed specifically to drive bus lines directly and all are 3-state except for 08, which is a totem-
pole output.
The 5N54AS877 is characterized for operation over the full military temperature range of -55°C to 125°C. The
1283
PRODUCT PREVIEW Copyright © 1982 by Texas I nstruments Incorporated
~ document containslnfonnatlon on a product under
development. TeX8sInstruments reserv •• the right to
change or discontinue this product without notic••
TEXAS 2-631
INSTRUMENTS
FUNCTION TABLE
MODE PORT
CLOCK SERIN A1 01 B1 A2 02 B2 A303B3 A4 04 B4 A5 05 B5 A6 06 B6 A7 07 B7 AS OSBS
S2 S1 SO FUNCTION
L L L H or L X Zan Al Zan A2 Z 0nA2 Z 0nA4 ZOnAS ZOnA6 ZOnA7 ZOn AS
ATO 8
L L L t X ZAl Al ZA2A2 ZA3 A3 Z A4A4 Z AS AS ZA6A6 ZA7 A7 ZA8A8
L L H H or L X 81 On Z 820 n Z 83 On Z 84 On Z 8S On Z 860n Z 87 On Z 88 On Z
8TOA
L L H t X 81 81 Z 8282 Z 8383 Z 8484 Z 8S 8S Z 8686 Z B7 B7 Z 88 B8 Z
L H L H or L X X On 01 X On 02 X On 03 X On 04 X On OS X On 06 X 0n07 X On 08
ON TO BN
L H L t X ZAl Al ZA2A2 ZA3 A3 Z A4A4 Z ASAS ZA6A6 Z A7 A7 Z A8A8
L H H H or L X 010 n X 020 n X 030 n X 040 n X OSOn X 06 On X 070 n X 08 On X
ON TO AN
L H H t X 81 Bl Z B2 82 Z 8383 Z 8484 Z B5 8S Z 86 B6 Z B7 B7 Z 88 B8 Z
H L L H or L X Z On 01 ZOn 02 Z On 03 Z On 04 Z On 05 ZOn 06 Z On 07 Z On 08 SHIFT
H L L t H ZHH Z0101 Z0202 Z 03 03 Z 0404 ZOSOS Z0606 Z 07 07 TO
H L L t L ZLL Z0101 Z 0202 Z 0303 Z 0404 ZOSOS Z 06 06 Z 07 07 8
H L H H or L X 01 On Z 020 n Z 030 n Z 04 On Z OSOn Z 06 On Z 07 On Z 080 n Z SHIFT
H L H t H HHZ 0101 Z 0202Z 0303 Z 0404Z OS OS Z 0606 Z 0707 Z TO
H L H t L LLZ 0101 Z 0202Z 0303Z 0404Z OSOSZ 0606 Z 0707 Z A
H H L HorL X Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z Z On Z
H H L t H ZHZ ZOl Z Z 02 Z Z 03 Z Z 04 Z Z OS Z Z 06Z Z07Z SHIFT
H H L t L ZLZ ZOl Z Z 02Z Z 03 Z Z 04Z Z OSZ Z 06Z Z07Z
H H H H or L X ZOn Z Z On Z Z On Z ZOn Z Z On Z Z On Z Z 0nZ Z On Z
CLEAR
H H H t X Z LZ ZLZ ZLZ ZLZ ZLZ ZLZ ZLZ ZLZ
n ~ level of 0n(n ~ 1. 2 ••• 8) established on most recent t transition of eLK. 01 thru 08 are the shift register outputs; oniy 08 is available
externallv. The double inversions that take place as data travels from port to port are ignored in this table.
lIB logic symbol

so (1)
[PORT CONTROLLER)
»
r
S1
S2
SRG8
en ClK
»
2
C SERIN 11 (21)
»
en
A1 (0/2)100
12
B1
n 13 (1/3)100
Z14
::D ;;'1 1=0 (20)
n A2 (0/2)100 B2
c 15 0
=i 16 (1/3)100 2/4
en A3
Z17
(19)
B3
(18)
A4
(17) : :
(16)
B6
(15) B7
1=0 ;;'1
(14)
A8 (0/2)100 (0/2/4) [>\7 B8
33 0 234
(1/3)100 (13) 08
2/4 35
235
1283
2-632 TEXAS
INSTRUMENTS
(21)
»-+-+-Bl
en
l-
=>
U
FOUR IDENTICAL CHANNELS NOT SHOWN
INPUTS/OUTPUTS NOT SHOWN:
a::
(6) A3
(7) A4
(19) B3
(lS) B4
u
(S) A5
(9) A6
(17) B5
(16) B6
en
<C
C
2
<C
en
..J
<C
(13)
~--------------------~L-------------------as
1283
TEN\S 2-633
INSTRUMENTS
8·81T UNIVERSAL TRANSCEIVER PORT CONTROLLERS
absolute maximum ratings over free·air temperature range

Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Voltage applied to a disabled 3·state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54AS877 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. -55°e to 125°e
SN74AS877 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. oOe to 70 e
0
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . _65° e to 150° e

SN54AS877 SN74AS877
UNIT
V,l low-level input voltage O.S O.S V
Al-AS, Bl-B8 -12 -15
IOH High-level output current mA
08 -2 -2
Al-AS, Bl-B8 32 48
08 20 20
-
Al-A8, Bl-BS
tsu Setup time before elK I SERIN ns
50,51,·52
Al-AS, Bl-B8
l> Hold time, data after ClK I SERIN
0 0
ns
r- th
en 50,51,52 0 0
l>
2 Additional information on these products can be obtained from the factory as it becomes available.
C
l>
en
n
::D
n
c
=i
(J)
1283
2-634 TEXAS
INSTRUMENTS
8-BIT UNIVERSAL TRANSCEIVER PORT CONTROLLERS
SN54AS877 SN74AS877
-18 rnA -1.2 -1.2 V
A1-A8 Vee = 4.5 V. IOH = -12 rnA 2.4 3.2
VOH 81-88 Vee = 4.5 V. IOH = -15 rnA 2.4 3.3 V
All outputs Vee =
4.5 V to 5.5 V. IOH = -2 rnA Vee- 2 Vee- 2
Vee - 4.5 V. IOl - 32 rnA 0.25 0.5
All outputs except Q8
VOL Vee = 4.5 V. IOl = 48 rnA 0.35 0.5 V
Q8 Vee = 4.5 V. IOl = 20 rnA 0.25 0.5 0.25 0.5
50.51.52 0.3 0.3
VCC = 5.5 V. VI = 7 V
II ClK and 5ERIN 0.1 0.1 rnA
A1-A8.81-88 VCC = 5.5 V. VI = 5.5 V 0.2 0.2
50.51.52 60 60
IIH ClK and 5ERIN VCC = 5.5 V. VI = 2.7 V 20 20 p.A
A1-A8.81-88:1: 70 70
50.51.52 -2 -2
III ClK and 5ERIN VCC = 5.5 V. VI = 0.4 V -0.3 -0.3 rnA
A1-A8.81-88:1: -0.35 -0.35
Except Q8 -30 -112 -30 -112
IO§ VCC = 5.5 V. Vo = 2.25 V rnA
Q8 -20 -112 -20 -112
Ice Vcc = 5.5 V 136 136 rnA

~For 1/0 ports. the parameters IIH and III include the output currents 10ZH and 10Zl. respectively.

Vcc = 4.5 V to 5.5 V.
en
Cl = 50 pF. !::
R1 = 500 fl. ::>
FROM TO R2 = 500 fl. u
PARAMETER
UNIT a::
SN54AS877 SN74AS877 u
MIN Typt MAX MIN Typt MAX en
f max 75
9.5
75
9.5
MHz
«
tplH
tpHl
Any A port Any 8 port
8 8
ns c
2
tplH
tpHl
Any 8 port Any A port
9.5
8
9.5
8
ns «
tplH
50.51.52
Any A or 8 12 12
ns
en
...I
tpHl
tplH
elK
port
Any A or 8
12
6.5
12
6.5
ns
«
tpHl port 12.5 12.5
tplH 9 9
ClK Q8 ns
tpHl 9 9
tpHZ 6 6
ns
tplZ Any A or 8 6 6
50.51.52
tpZH port 10 10
ns
tpZl 10 10

1283
TEXAS 2-635
INSfRUMENTS
BUS A TO BUS B OR BUS B TO BUS A OR

SERIAL TRANSMISSION SERIAL TRANSMISSION
SERIAL IN SERIAL IN
CLK CLK
I REG
I I
I I I
AI IB IB
I I /
I I I
-
I /
I I
/B IB
» I I
r- I I
CA
».
2
C SERIAL SERIAL
»
CA
OUT OUT
SERIAL IN TO A PORT SERIAL IN TO B PORT

Q SERIAL IN _ _ _ _ _---, SERIAL IN _ _ _ _ _--.
:xJ CLK------. CLK------,
(')
c:
~ I I
CA
I /
IB Hi-Z Hi-Z IB
I /
/ I
SERIAL SERIAL
OUT OUT
128::
2-636
TEXAS
INSTRUMENTS
DUAL 4·81T D·TYPE EDGE·TRIGGERED FLIP-FLOPS WITH 3·STATE OUTPUTS
D2661. APRil 1982-REVISED DECEMBER 1983
o 3-State Bus-Driving Outputs SN54ALS878. SN54AS878 .•. JT PACKAGE

SN74ALS878. SN74AS878 ... NT PACKAGE
o Full Parallel-Access for Loading (TOP VIEW)
Cit Buffered Control Inputs lClR VCC

lOC lClK
lDl 101
o Choice of True or Inverting Logic
102
'ALS878, 'AS878 True Outputs 103
'ALS879, 'AS879 Inverting Outputs 104
201
• Synchronous Clear 202
203
.. Package Options Include Both Plastic and Ceramic Chip 2D4 10 15 204
Carriers in Addition to Plastic and Ceramic DIPs 20C 11 14 2ClK
GND 12 13 2CLR
o Dependable Texas Instruments Quality and Reliability SN54ALS878. SN54AS878 ..• FH PACKAGE
These dual 4-bit registers feature three-state outputs designed
algid 8d 0
- __ uz> __
suitable for implementing buffer registers. 110 ports. bidirectional 4 3 2 1 282726

lD2 5 102
bus drivers. and working registers.
103 6 103
104 104
The dual 4-bit edge-triggered flip-flops enter data on the low-to-
NC NC
high transition of the clock (1 ClK and 2ClK). All types have 201 201
individual synchronous clear inputs and output control pins for 202 10 202
203 11 203
each group of 4-bit registers.
12131415161718
The SN54AlS878. SN54AlS879. SN54AS878. and
~Ig ~ ~q5 ~ ~
SN54AS879 are characterized for operation over the full military NNCl ~~N
temperature range of - 55 °C to 125°C. The SN74AlS878, SN54ALS879. SN54AS879 ... JT PACKAGE

SN74AlS879. SN74AS878. and SN74AS879 are characteriz- SN74ALS879. SN74AS879 ... NT PACKAGE
C/)
ed for operation from 0 °C to 70 o C. (TOP VIEW)
lCLR 24 Vce !=
lac 23 lCLK :>
101 3 22 101 (J
102
103
4 21
20
lQ2
103
a:
104 19 104 (J
201 18 201
202 17 202 C/)
203
204
9
10
16
15
203
204
«
ioe 11 14 2CLK
c
GNO 12 13 2CIR
z
SN54ALS879. SN54AS879 •.. FH PACKAGE'
SN74ALS879. SN74AS879 ..• FN PACKAGE
«
(TOP VIEW)
C/)
..J
algid u 8dlo
~~~Z>~~
«
4 3 2 1 28 2726
102 5
103
104
NC
201
202 10
203 11
12131415161718
~Ig ~ ~IdN N
NN(,!)
dl~
N

TEXAS 2-637
INSTRUMENTS
DUAL 4·811 D·TYPE EDGE·TRIGGERED FLlp·FLOPS WITH 3·STATE OUTPUTS
FUNCTION TABLES
'ALS878, 'AS878 'ALS879, 'AS879
(EACH FLIP-FLOP) (EACH FLIP-FLOP)
OC CLR CLK D Q OC CLR CLK D Q
L L t X L L L t X H
L H t H H L H t H L
L H t •L L L H t L H
L H L X 00 L H L X 00
H X X X Z H X X' X Z
logic symbols
'ALS878, 'AS878 'ALS879, 'AS879
(221 101
(211 102
(201 103
(191 104
(181 201
201 ~1;;;..0--:;_....:....j
202 (81 (171 202
~ 203 (9)
204 (10)
(161 203
(151
204
»
r- logic diagrams (positiye logic)
en 'ALS878, 'AS878 (EACH QUAD FLIP-FLOP) 'ALS879, 'AS879 (EACH QUAD FLIP-FLOP)
»
2 oc----------------~~--------~ oc ---------------<21 ~----~
CLK-----I CLK-----t
C
»
en
CLR CLR
(")
01--+--~~ 01--+-L~
::a
(")
c 02 02
=i
en 02--t---L-~ 02--t---L-~
03
03 ---t--"'--~
----04
04----1 04 ---"---~
1283
2-638 TEXAS .
INSTRUMENlS
DUAL 4·81T D·TYPE EDGE·TRIGGERED FLlp·FLOPS WITH 3·STATE OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; ..... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : .......... 5.5 V
Operating free-air temperature range: SN54ALS878, SN54ALS879 . . . . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74ALS878,SN74ALS879 . . . . . . . . . . . . . . . . . . . . . . . OOeto700e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 150 °e

UNIT
IOL low-level output current 12 24 mA
'AlS878 0 25 0 30
, AlS879 0 20 0 25
'AlS878 elK high or low 20 16.5
'AlS879 elK high or low 25 20
tsu ns
before elKt elR 20 20
Hold time Data 4 4
th ns
after elKt elR 0 0
en
l::
SN54ALS878 SN74ALS878 ::>
PARAMETER TEST CONDITIONS SN54ALS879 SN74ALS879 UNIT u
MIN Typt MAX MIN Typt MAX a:
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V U
en
VOH Vee = 4.5 V. IOH = -1 mA 2.4 3.3 V
<t
Vee = 4.5 V. IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V. IOl = 12 mA 0.25 0.4 0.25 0.4
V
o
Val
Vee = 4.5 V. IOl = 24 mA 0.35 0.5 2
IOZH Vee = 5.5 V. Va = 2.7 V 20 20 p.A <t
IOZl Vee = 5.5 V. Va = 0.4 V -20 -20 p.A en
-I
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 p.A <t
III Vee = 5.5 V, VI = 0.4 V -0.2 -0.2 mA
lot Vee = 5.5 V. Va = 2.25 V -15 -70 -15 -70 mA
1283
TEXAS 2-639.
INSTRUMENTS

Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
R1 = 5000,
FROM TO R2 = 5000,
PARAMETER UNIT
MIN MAX MIN MAX
'ALS878 25 .30
f max MHz
'ALS879 20 25
tpLH Q ('ALS878) or 4 15 4 14
eLK ns
tpHL Q ('ALS879) 4 17 4 16
tpZH Q ('ALS878) or 4 22 4 20
5C Q ('ALS879)
ns
tpZL 4 22 4 20
tpHZ Q ('ALS878) or 2 12 2 10
5C Q ('ALS879)
ns
tpLZ 3 16 3 13
o flip·flop signal conventions

It is TI practice to name the outputs and other inputs of a Ootype flip-flop and to draw its logic symbol based on the
producing complementary data are called Q, An input that causes a Q output to go high or a Q output to go low is called
-.J Preset; an input that causes a IT output to go high or a Q output to go low is called Clear. Bars are used over these pin
r- outputs should be renamed as shown below. Also shown are corresponding changes in the graphical symbol. Arbitrary
en pin numbers are shown in parentheses.
l>
2
C
l> Pll£ CLR (5)
Q
en ClK C1 CLK C1
o 0
Q
0 (6) Q
:JJ etA PRE

o
c
=i
CJ)
N9tice that Q and Q exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (I:::..) on PRE and eLR remain since these inputs are still active-low, but that the presence or absence of the
! polarity indicator changes at 0, Q, and Q. Of course pin 5 (a) is still in phase with the data input 0, but now both are
1283
2-640 TEXAS
INSTRUMENTS
POST OFFice BOX 225012 • OALLAS. TeXAs 75265
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS878, SN54AS879 . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS878, SN74AS879 . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 150 °e

SN54AS878 SN74AS878
SN54AS879 SN74AS879
UNIT
Vil low·level input voltage 0.8 0.8 V
elK low 3 2
elK high 5 4
Setup time Data 3 2
tsu ns
before elKt elR 6.5 5.5
Hold time Data 3 2
th ns
after elKt elR 0 0
TA Operating free·air temperature -55 125 0 70 °e
SN54AS878 SN74AS878 (J)
PARAMETER TEST CONDITIONS SN54AS879 SN74AS879 UNIT !:::
MIN Typt MAX MIN Typt MAX ::::>
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V u
Vee =
4.5 V to 5.5 V, 10H = -2mA VCC- 2 VCC-2 a::
VOH Vee = 4.5 V, 10H = -12 mA 2.4 3.2 v u
Vee = 4.5 V, 10H = -15 mA 2.4 3.3
(J)
VOL
Vee
Vee
=
=
4.5 V,
4.5 V
10l = 32 mA
10l = 48 mA
0.29 0.5
0.33 0.5
V «
IOZH Vee = 5.5 V, Vo = 2.7 V 50 50 JlA o
10Zl Vee = 5.5 V, Vo = 0.4 V -50 -50 JlA z
II Vee = 5.5 V, VI =7V
VI = 2.7 V
0.1
20
0.1 mA «
IIH Vee = 5.5 V, 20 JlA (J)
0 -3 -2 ..J
III
10+
All other
Vee = 5.5 V,
Vee = 5.5 V,
VI = 0.4 V
Vo = 2.25 V -30
-0.5
-112 -30
-0.5
-112
mA
mA
«
'AS878 Outputs low 96 155 96 155
Vee = 5.5 V, Outputs disabled 100 160 100 160
lee mA
See Note 1 Outputs high 88 142 88 142
'AS879 Outputs low 94 150 94 150

+The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
NOTE 1: lee is measured with elR and all D inputs grounded, and elK and oe at 4.5 V.
1283
TEXAS 2-641
INSTRUMENTS
DUAL 4·BIT D·TYPE EDGE·TRIGGERED FLlp·FLOPS WITH 3·STATE OUTPUTS

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 500 n,
FROM TO R2 = 500 n,
PARAMETER UNIT
SN54AS878 SN74AS878
SN54AS879 SN74AS879
MIN MAX MIN MAX
f max 100 125 MHz
tPlH Q ('AS878) or 3 11.5 3 8.5
elK ns
tpHl Q ('AS879) 4 12.5 4 10.5
tpZH Q (' AS878) or 2 8 2 7
oe ns
tPZl Q ('AS879) 3 11.5 3 10.5
tPHZ Q (' AS878) or 2 7 2 6
oe ns
tPlZ Q ('AS879) 2 7 2 6
IIfJ
l>
r
CJ)
l>
2
C
l>
CJ)
n
:ll
n
C
~
CJ)
1283
2-642 TEXAS
INSTRUMENlS
• 3·State Buffer-Type Outputs Drive Bus-Lines Directly

~ 'ALSB73 Is Alternotivo Vorsion with Noninverting
SN54ALS880, SN54AS880 . • • JT PACKAGE
Outputs
SN74ALS880. SN74AS880 . • . NT PACKAGE
• Package Options Include Both Plastic and Ceramic (TOP VIEW)
1 PRE VCC
description 10C 1C
101 101
These dual 4-bit registers feature three-state outputs designed
102 102
103 10.3
104 104
bus drivers, and working registers.
201 201
The dual 4-bit latches are transparent Ootype. While the latch 202 20.2
enable input (1 C or 2C) is high, the Q outputs will follow the data 20.3
(0) inputs in inverted form, according to the function table. When 204 20.4
the latch enable input is taken low, the outputs will be latched. 20C 2C
When PRE goes low, the Q outputs go low independently of the GNO 2PRE
clock. The outputs are in a high-impedance state when OC
(output control) is at a high logic level.

operation over the full military temperature range of - 55°C to SN54ALS880,SN54AS880. FH PACKAGE
125°C. The SN74ALS880 and SN74AS880 are characterized SN74ALS880,SN74AS880. FN PACKAGE
for operation from ooC to 70°C. (TOP VIEW)
.- I<J I~
010 0.. U UUIO
U .-
............... z> ..........
4 3 2 1 282726
FUNCTION TABLES (EACH LATCH)
102 25 10.2
INPUTS OUTPUT 103 Hi3
OC PRE ENABLE C D Q 104 104
L L X X L NC NC
L H H H L 201 20.1
L H H L H 202 202
L H L X 00 203 20.3
H X X X Z 12 1314151617 18
..;tIUOUIWU..;t
oozzg:NIO
NNl!) N N

1283
TEXAS 2-643
INSTRUMENTS
DUAL 4-81T OoTYPE LATCHES WITH 3-STATE OUTPUTS
logic symbol
logic diagram (each quad latch, positive logic)
OC -------0(1/-----,
C
PRE
III 01 ----+-+--4
»
r-
VJ
»
2
02 -----+-+--4
C
»
VJ 03 ------+-+--4
Q
:lJ
(')
c 04 ---------~ 1--__1.;><)---- Q4
=i
CJ)
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS880, SN54AS880 . . . . . . . . . . . . . . . . . . . - 55 °e to 125°C
SN74ALS880,SN74AS880 . . . . . . . . . . . . . . . . . . . . . . . 0 0 Cto70oC
1283
2-644 TEXAS
INSffiUMENlS
TYPES SN54ALS88D, SN74ALS88D
DUAL 4·81T O·TYPE LATCHES WITH 3·STATE OUTPUTS

UNIT
VIH High-level input voltage 2- 2 V
Pulse duration
I PRE low 15 15
tw ns
I Enable e high 15 15
tsu Setup time, data before enable e + 10 10 ns
th Hold time, data after enable e + 10 10 ns
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 mA Vcc-2 vcc- 2
VOH Vee = 4.5 V, 10H = -1 mA 2.4 3.3 V
Vee = 4.5 V, 10H = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10l = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, 10l = 24 mA 0.35 0.5
10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 p.A
10Zl Vee = 5.5 V, Vo = 0.4 V -20 -20 p.A
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7 V 20 20 p.A
III Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
10-; Vee = 5.5 V, Vo = 2.25 V -15 -70 -15 -70 mA
t All typical values are at V CC = 5 V, T A = 25 DC.
1283
TEXAS 2-645
INSlRUMENTS
DUAL 4·811 D·TYPE LATCHES WITH 3·STATE OUTPUTS

Vee = 4.5 V to 5.5 V,
eL = 50 pF,
R1 = 500 Q,
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tPLH 3 23 3 20
D Q ns
tPHL 3 15 3 14
tPLH 8 31 8 24
e 5 22 8 21
ns
tPHL 8
tPHL PRE Q 6 24 6 21 ns
tpZH 4 21 5 18
OC 5 21 5 18
ns
tPZL 4
tPHZ 2 10 2 8
DC 5 15 3 13
ns
tPLZ 3
..
l>
r-
en
o latch signal conventions
It is TI practice to name the outputs and other inputs of a Ootype latch and to draw its logic symbol based on the
a
producing complementary data are called Q. An input that causes a Q output to go high or a output to go low is called
Preset; an input that causes a Q output to go high or a Q output to go low is called Clear. Bars are used over these pin
In some applications it may be advantageous to redesignate the data input D. In that case all the other inputs and
l> pin numbers are shown in parentheses.
:2
C
l>
en PRE S (5) Q CLR R (5)
Q
C1 C C1
~ C
:JJ o 10
(6) a. i5 10 (6)
'Q
o CLR R PRE s
c
=t
en Notice that Q and a exchange names, which causes Preset and Clear to do likewise. Also notice that the polarity
indicators (1:::..) on PRE and CLR remain since these inputs,are still active-low, but that the presence or absence of the
polarity indicator changes at D, Q, and O. Of course pin 5 (0) is still in phase with the data input D, but now both are
1283
2-646 TEXAS
INSTRUMENTS
DUAL 4-81T D-TYPE LATCHES WITH 3-STATE OUTPUTS

SN54AS880 SN74AS880
UNIT
tw Pulse duration
I PRE low 4.5 3.5
ns
I Enable e high 3.5 2.5
tsu Setup time, data before enable e~ 2 2 ns
th Hold time, data after enable e~ 1 1 ns
SN54AS880 SN74AS880
VIK Vee = 4.5 V, II
-18 mA = -1.2 -1.2 V
..
Vee =
4.5 V to 5.5 V, IOH = -2 mA Vee- 2 Vee- 2
VOH Vee = 4.5 V, IOH = -12 mA 2.4 3.2 V
Vee = 4.5 V, IOH = -15 mA 2.4 3.3
Vee = 4.5 V, IOl = 32 mA 0.30 0.5
Val V
Vee = 4.5 V, IOl =48 mA 0.35 0.5
IOZH Vee = 5.5 V, Va = 2.7 V 50 50 p.A
IOZl Vee = 5.5 V, Va = 0.4 v -50 -50 p.A en
II Vee =
=
5.5 V, VI = 7 V 0.1 0.1 mA !::
IIH Vee 5.5 V, VI= 2.7 V 20 20 p.A ::::>
III Vee = 5.5 V, VI= 0.4 V -0.5 -0.5 mA u
lot Vee = 5.5 V, Va = 2.25 V -30 -112 -30 -112 mA a:
u
I Outputs disabled 86 137 86 137 en
tAli typical values are at Vee = 5 V, TA = 25°e. cd:
o
2:
cd:
en
...J
cd:
1283
TEXAS 2-647
INSTRUMENTS
DUAL 4·81T o·TYPE LATCHES WITH 3·STATE OUTPUTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
SN54AS880 SN74AS880
MIN MAX MIN MAX
tPLH 4 11 4 9.5
0 Q ns
tpHL 4 9 4 8.5
tpLH 6 14 6 11.5
C Q ns
tpHL 4 10 4 8
tpHL PRE il 4 11.5 4 10 ns
tpZH 2 8 2 7.5
OC Q ns
tpZL 4 11 4 10
tpHZ 2 8 2 6.5
OC IT ns
tPLZ 2 9 2 8
16
l>
r-
en
l>
:2
C
l>
en
n
-.
::D
n
c
=i
en
1283
2-648 TEXAS
INSTRUMENlS
TYPES SN54AS881A. SN74AS881A
ARITHMETIC LOGIC UNITSIFUNCTION GENERATORS
02661, DECEMBER 1982-REVISED DECEMBER 19B3
• The 'AS881A is Offered in 300-mil DIPS and 5N54A5181A ... J OR JT PACKAGE

is Available in Both Plastic and Ceramic Chip 5N54A5881A, .. JT PACKAGE
Carriers 5N74A5181A. , . N OR NT PACKAGE
5N74A5881A ... NT PACKAGE
• Full Look-Ahead for High-Speed Operations (TOP VIEW)
on Long Words
80 VCC
• Arithmetic Operating Modes: AO A1
Addition
S3 81
Subtraction
S2 A2
Shift Operand A One Position S1 82
Magnitude Comparison
SO A3
Plus Twelve Other Arithmetic Operations
Cn 83
• Logic Function Modes M G
Exclusive-OR Fa C n +4
Comparator F1 p
AND,NAND,OR,NOR F2 A=B
'AS881A Provides Status Register Checks GND F3
Plus Ten Other Logic Operations
• Dependable Texas Instruments Quality and 5N54A5181A, 5N54A5881A ... FH PACKAGE
Reliability 5N74A5181A, 5N74A5881A ... FN PACKAGE
'A5181A, 'A5881A
(TOP VIEW)
logic symbol U
("I) 0 0 U u..-..-
cnl<Clal z > I<C lal
4 3 2 1 282726
so
(6)
(5) O} ALU A2 en
P
51
52
(4)
(0 ••• 15) CP
Mt, (0 ... 15) CG G
82
A3
!::
(3) ::J
53 6(P=QI~ A=B NC NC U
M
(8)
(7)
4 (0 ... 151 CO C n +4 Cn 83 a:
Cn M G (J
Fa 11 Cn +4
12 131415161718 en
AO
BO
FO
IU:::I~ ~ ~112 ~Ia.
«
Al (!) <C c
(2) z
Bl
A2
NC-No internal connection «
82
(4) en
..oJ
A3
83
(8) «
Pin numbers shown are J, JT, N and NT packages.
For complete information on the SN54AS881A and the SN74AS881A, see page
1283 ADVANCE INFORMATION Copyright © 1982 by Texas Instruments Incporated

This document contain. information on 8 new product.
INSTRUMENTS
2-650
32·81T LOOK·AHEAD CARRY GENERATORS

• Directly Compatible with the New' AS 181 A SN74AS882 ... NT PACKAGE
and 'AS881A ALU's (TOP VIEW)
• Included among the Package Options Are CN VCC

Compact, 24-Pin, 300-mil-Wide DIPs and GO NC
Both 28-Pin Plastic and Ceramic Chip Car- PO CN+32
riers G1 P7
P1 G7
• Capable of Anticipating the Carry Across a CN+8 P6
Group of Eight 4-Bit Binary Adders G2 G6
152 CN+24
• Cascadable to Perform Look-Ahead Across
G3 P5
n-Bit Adders
P3 G5
• Typical Carry Time, Cn to Any Cn + i, Is Less CN+16 P4
Than 6 ns (CL = 15 pF) GND G4
• Dependable Texas Instruments Quality and SN54AS882 ... FH PACKAGE

Reliability SN74AS882 ... FN PACKAGE
(TOP VIEW) N
C"l
U +
description oOzuuuz
1a..1(!) U Z > Z U
The 'AS882 is a high-speed look-ahead carry 4 3 2 1 282726
generator capable of anticipating the carry across a P7
group of eight 4-bit adders permitting the designer to G7
implement look-ahead for a 32-bit ALU with a single P6
package or, by cascading' AS882's, full look-ahead NC
is possible across n-bit adders. G6
CN+24
The SN54AS882 is characterized for operation over
P5 en
125°C. The SN74AS882 is characterized for opera-
12131415161718
t::
tion from OOC to 70°C.
C"l
10..
(00 U
~Z
'<t '<t L!'l
zl(!)10.. I(!) ::J
+(!) U
U
z ex:
U
'AS882 LOGIC EQUATIONS logic symbol
,..-----.., en
Cn +8 = G1 +P1GO+P1POC n
CPG
<t
C
Cn +16 = G3+P3G2+P3P2G1 +P3P2P1GO
+ P3P2P1 POC n z
<t
Cn + 24 = G5 + P5G4 + P5P4G3 + P5P4P3G2
+P5P4P3P2G1+P5P4P3P2P1GO (6) Cn+8
en
...J
COl
+ P5P4P3P2P1 POC n
111)
<t
Cn +32 = G7+P7G6+P7P6G5+P7P6P5G4 C03 Cn +16
+P7P6P5P4G3+P7P6P5P4P3G2
(171 C n +24
+P7P6P5P4P3P2G1+P7P6P5P4P3P2P1GO C05
+P7P6P5P4P3P2P1POC n (22)
C07 Cn+32
ADVANCE INFORMATION Copyright © 1982 Texas Instruments Incorporated

1283
ThIs document contaln. Infonnatlon on a new product.
Specillcations ara subjoct to changa without notice. TEXAS 2-651
INSTRUMENTS
32·811 LOOK·AHEAD CARRY GENERATORS
FUNCTION TABLE
FOR Cn + 32 OUTPUT
INPUTS OUTPUT
G7 G6 G5 G4 G3 G2 61 GO 157 P6 P5 P4 153 152 151 ]So Cn Cn +32
L X X X X X X X X X X X X X X X X H
X L X X X X X X L X X X X X X X X H
X X L X X X X X L XL X X X X X X H
X X X L X X X X L L L X X X X X X H
X X X X L X X X L L L L X X X X X H
X X X X X L X X L L L L L X X X X H
X X X X X X L X L L L L L L X X X H
X X X X X X X L L L L L L L L X X H
X X X X X X X X L L L L L L L L H H
FUNCTION TABLE
FOR Cn + 24 OUTPUT
INPUTS OUTPUT
..
65 G4 G3 G2 . G1 GO P5 P4 P3 P2 P1 PO Cn Cn +24
L X X X X X X X X X X X X H
X L X X X X L X X X X X X H
X X L X X X L L X X X X X H
X X X L X X L L L X X X X H
X X X X L X L L L L X X X H
:t> X X ·X X X L L L L L L X X H
r- X X X X X X L L L L L L H H
(J) All other combinations L
:t>
2
o FUNCTION TABLE FUNCTION TABLE
:t>
(J)
FOR Cn + 16 OUTPUT FOR Cn + 8 OUTPUT

(1
63 02 G1 GO P3 P2 P1 PO Cn Cn +'16 G1 GO P1 PO Cn Cn +8
:Il L X X X X X X X X H L X X X X H
(1 X L X X L X X X X H X L L X X H
c X X L X L L X X X H X X L L H H
=4 X X X L L L L X X H All other combinations L
en X X X X L L L L H H
Any inputs not shown in a given table are irrelevant with respect to that output.
1283
2-652 TEXAS
INSTRUMENTS
P7
(21)
cD-
P6
(19) ~~
(16) ~F=n-
~
(14) i-F=I
P4
"-~ ~ ~ (22)
(10) Cn +32
P3
~~ ~
. (8)
~
)--
(5)
P1
~
(3)
r-
PO
::::1
)--
67
66
65
04
(20)
(18)
(15)
(13)
lJ--
-;tLJ
(17)
C n +24
..C/)
!::
:::>
63
(9)
~ i=f u
a:
(7)
il2 '==-=-t
}--
u
(4) C/)
61 ~ <t
)--
(2)
C
~O 2
-
I <t
~
C/)
-J
, (11)
C n + 16 <t
.--.
~ C n +8
Cn
(11 -~
1283
TEXAS 2-653
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS882 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
,SN74AS882 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '..... - 65 °e to 1 50 °e

SN54AS882 SN74AS882
UNIT
- l>
r-
C/)
l>
:2
C
l>
C/)
-
(')
:::D
(')
c
=i
C/)
1283
2-654 TEXAS
INSTRUMENlS
SN54AS882 SN74AS882
Mlr~ Typt MAX MIN Typt MAX
VIK Vee = 4.5 V. II = -18 rnA -1.2 -1.2 V
VOH Vee = 4.5 V. to 5.5 V. 10H = -2 rnA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V. 10L = 20 rnA 0.3 0.5 0.3 0.5 V
en 0.5 0.5
GO.G6 4 4
Gl. G2. G4 6 6
G3 7.5 7.5
G5 7 7
II
G7
Vee = 5.5 V. VI =7V 4.5 4.5
rnA
PO. Pl 2 2
P2. P3 1.5 1.5
P4. P5 1 1
P6. P7 0.5 0.5
en 0.2 0.2
GO.G6 1.6 1.6
Gl.G2.G4 2.4 2.4
G3 3 3
G5 2.8 2.8
IIH Vee"; 5.5 V. VI = 2.7 V rnA
G7 1.8 1.8
PO. Pl 0.8 0.8
P2. P3 0.6 0.6
P4. P5 0.4 0.4
P6. P7 0.2 0.2
en -3 -3
GO -26 -26 en
Gl -37 -37 !:::
G2 -40 -40 :::l
G3 -47 -47 U
G4 -41 -41 a::
G5 -44 -44 U
IlL G6.G7 Vee = 5,5 V. VI = 0.4 V -28 -28 rnA
en
PO
'Pl
-13
-11
-13
-11
«
P2 -9 -9 o
P3 -8 -8 2
P4 -5 -5 «
15"5 -4 -4
en
l5'6.15"7 -2 -2 ...J
10:1: Vee = 5.5 V. Vo = 2.25 V -150 -150 rnA «
lee Vee = 5.5 V 72 105 72 105 rnA
*The output conditions have been chosen to produce a current that closely approximates one-half of the true short-circuit, lOS'
1283
TEXAS 2-655
INSTRUMENTS
32·BIT LOOK·AHEAD CARRY GENERATORS

Vec = 4.5 V to 5.5 V.
CL = 50 pF.
,FROM TO RL = 500 n.
PARAMETER UNIT
SN54AS822 SN74AS882
MIN MAX MIN MAX
tpd Cn Any output 4 15 4 14
tpd P or G Cn + 8 2 9 2 8
tpd P or G en + 16 2 9 2 8 ns
tpd P or G en + 24 2 11 2 10
tpd Por~ en + 32 2 13 2 12
tpd = tPHL or tpLH'

The application given in figure 1 illustrates how the' AS882 can implement look-ahead carry for a 32-bit ALU (in this
case. the popular' AS881) with a single package. Typical carry times shown are derived using the standard Advanced
Schottky load circuit with CL = 15 pF.
A B A If
PO GO PI Gl Cn +8
cn 'AS882
1283
2-656 TEXAS
INSTRUMENTS
(
8·81T MAGNITUDE COMPARATORS
D2661. DECEMBER 19B2-REVISED DECEMBER 1983
SN54AS885 •••• JT PACKAGE

• Included among the Package Options Are
SN74AS885 •••• NT PACKAGE
Compact, 24-Pin, 300-mil DIPs and Both (TOP VIEW)
28-Pin Ceramic and Plastic Chip Carriers
• Latchable P Input Ports with Power-Up Clear L/A 1 U24 Vcc
P<OIN 2 23 PLE
• Choice of Logical or Arithmetic (2's Com· P>OIN 3 22 P7
plement) Comparison 07 4 21 P6
06 5 20 P5
• Data and PLE Inputs Utilize P-N-P Input 05 6 19 P4
Transistors to Reduce DC Loading Effects 04 7 18 P3
• Approximately 35% Improvement in AC 03 8 17 P2
02 9 16 P1
Performance Over Schottky TTL while
01 10 15 PO
Performing More Functions
• Cascadable to n-Bits while Maintaining High GND
00 11
12
14
0
P<OOUT
130 P>OOUT
Performance .
• 10% Less Power than STTL for an 8-Bit
Comparison
SN54AS885 •.•• FH PACKAGE
• Dependable Texas Instruments Quality and SN74AS885 .•.• FN PACKAGE
Reliability ITOPVIEW)
4 3 2 1 282726
description P6
These advanced Schottky devices are capable of P5
performing high-speed arithmetic or logic comparisons P4 en
on two 8-bit binary or two's complement words. Two NC
P3
!::
fully decoded decisions about words P and Q are :::>
externally available at two outputs. These devices are
P2
P1 u
fully expandable to any number of bits without
12131415161718
a::
external gates_ The P > Q and P < Q outputs of a
~OOUI-I-O
U
stage handling less-significant bits may be connected ddzZ:J:Jo.
to the P > Q and P < Q inputs of the next stage t!) 00 en
handling more-significant bits to obtain comparisons
dd
~~ «
of words of longer lengths. The cascading paths are o
implemented with only a two-gate-Ievel delay to 2
reduce overall comparison times for long words. Two
alternative methods of cascading are shown in the
«
typical application data.
en
..J
The latch is transparent when P Latch Enable (PLE) is high; the P input port is latched when PLEis low. This provides
«
the designer with temporary storage for the P data word. The enable circuitry is implemented with minimal delay times
to enhance performance when cascaded for longer words. The PLE and P and Q data inputs utilize p-n-p input tran-
sistors to reduce the low-level current input requirement to typically -0.25 mA, which minimizes de loading effects.
The SN54AS885 is characterized for operation over the full military temperature range of _55°C to 125°C. The

1283
TEXAS 2-657
INSTRUMENTS
8·81T MAGNITUDE COMPARATORS
PlE
(23)'c1
-r>-<:
-....... P7 = 07
P7
22)
- 10
P7 --
I-
P7 ~ P6=06
P6 (21) P6
-
r-
P6
tg}D P5=05
;t
P5
P5 (20)- P5
r-c 1
( 19)
- P4 -.......
L-' P3 = 03
P4 - ~
~~~
~
18)
P3 ( -
t--
P3 - P2= 02
t--
P3 -
~
P2 ( 17) P2
" ~ 4) P<O
....... Pl =01
-
r-
P2 ~
-
~
")--
16) Pl
Pl ( - Pl
PO=~O ~1--
15)
I-
PO
.......
........ I '-~
r-Ff
-
PO - I 4==1-'
PO
'--
~
~
I II
l>
~J
r-
CJ)
l>
2
C
07
06
05
(~
v 07
(5) "
(6) ...
~
.
06
06
05
~
~II
§L
l> 05 F=i}--- (1
~ 3)
~
P>O
CJ) (7) ... 04
.
4J
04
n 04
:xJ (8) " 03

I
n
c:
03
03
:J 4MSB=
=i
CJ)
02
01
(9) ...
.
(10) ...
(11)" 00
..
02
02
01
01
--
J--
::r-
B
00 00
P>O in
P<O in
L/A ... ARITH
(1) I ."" lOGIC
Pin numbers sh"own are for JT and NT packages.
1283
2-658 TEXAS
INSTRUMENTS
8-BIT MAGNITUDE COMPARATORS
logic symbol
COMP
P2
P3
P4
P5
P6
P7
P'>O P'>O P'>O
P<O P<o P<O
QO
01
Q2
03
04
as
os
07
en
FUNCTION TABLE !::
::::>
DATA INPUTS INPUT INPUT OUTPUTS u
COMPARISON L/A
PO.p7, 00·07 P>O P<O P>O P<O
a:
LOGICAL H P>O X X H L u
LOGICAL H P<O X X L H
en
LOGICAL·
ARITHMETIC
H
L
P=Q
PAGQ
H OR L
X
H OR L
X
HOR L
H
H OR L
L
«
ARITHMETIC L QAGP X X L H c
z
ARITHMETIC· L P=Q H OR L H OR L H OR L
·In these cases the P>O output will follow the P>O input, and the P<O output will follow the P<O Input.
H OR L
«
AG - arithmetically greater than en
..J
«
Supply voltage, Vee ............................................................ 7V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Operating free·air temperature range: SN54AS885 . . . . . . . . . . . . . . , . . . . . . . . . . . . . . .. -55°C to 125°C
SN74AS885 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. oOe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to 150°C
1283
TEXAS 2-659
INSTRUMENTS
TYPES.SN54AS885. SN74AS885

SN54AS885 SN74AS885
PARAMETER UNIT
tsu Setup time to PLE ~ 2 2
ns
th Hold time after PLE ~ 4 4
electrical characteristics over recommended operating free~air temperature range (unless otherwise noted)
SN54AS885 SN74AS885
V,K Vee = 4.5 V, I, = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5V, 10H = -2 mA Vee- 2 Vee- 2 V
VOL Vee = 4.5 V, 'OL = 20 mA 0.35 0.5 0.35 0.5 V
Vee = 5.5 V, V, = 7 V 0.1 0.1 p.A
"
LlA 40 40
"H Vee = 5.5 V, V, = 2.7 V p.A
Others 20 20
LlA -4 -4
--
P> Qjn
',L Vee = 5.5 V, V, == 0.4 V -2 -2 mA
P < Qjn
P, Q, PLE -1 -1
'0; Vee = 5.5 V, Vo = 2.25 V -20 -112 -20 -112 mA
lee Vee = 5.5 V. See Note 1 130 210 130 210 mA
l>
r- t All typical values are at Vee = 5 V, TA = 25°C.
en *The output conditions have been chosen to produce a current that closely approximates one half of the true short· circuit output current, lOS.
NOTE 1: ICC is measured with all inputs high except LlA, which is low.
l>
2
C
l>
en Vcc = 4.5 V to 5.5 V,
= 50 pF,
o CL
:so PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL
TA
= 500 fl,
= MIN to MAX UNIT
c: SN54AS885
MIN Typt MAX
SN74AS885
MIN Typt MAX
=i tpLH 8.5 14 8.5 13
cn tPHL
LlA
7.5 14 7.5 13
ns
tPLH P < Qjn P < Q, 5 10 5 8

ns
tpHL P> Qin P>Q 5.5 10 5.5 8
tPLH Any P or Q 13.5 21 13.5 17.5
ns
tpHL Data Input 10 17 10 15

1283
2-660 ,TEXAS
INSTRUMENTS

The ' AS885 can be cascaded to compare words longer than 8-bits. Figure 1 shows the comparison of two 32-bit words;
however, the design is expandable to n-bits. Figure 1 shows the optimum cascading arrangement for comparing words of
32 bits or greater. Typical delay times shown are at Vee = 5 V, T A = 25°e, and use the standard Advanced Schottky load of
RL = 500 n, eL = 50 pF.
PLE
P>O (13)
P<O (14)
II OR L ....._+-..;...;:~~
02
03
04
05
06 PLE
(4)
P>O~;;...-- _ __
H OR L -..--...;...;;~~ P<O~~_---.
!
(20)
P5
(4) P6 (21)
07
P7 (22)
P>O (3) (13)
P>O P>O
P<O (2) (14)
P<O P>O
ao (II)
01 (10)
(13) (9)
(14) (8)
HOR L (7)
04
as (6)
06 (5)
07 (4)
~
P5 (20)
P6 (211
P7(22)
P>O (3) p>O (13)
KO (2) P<O (14)
00 (11)
01 (10)
02 (9)
03 (8)
Q4 (7)
as (6)
06 15)
07 (4)
:;0.
FIGURE 1 - 32-BIT TO 72 (N)-BIT MAGNITUDE COMPARATOR
1283
TEXAS 2-661
INSTRUMENlS
The method shown in Figure 2 is the fastest cascadi'ng arrangement for comparing 16-bit or 24-bit words. Typical delay times
shown are at Vee = 5 V, T A = 25°e, and use the standard Advanced Schottky load of R L = 500 n~ eL = 50 pF.
E~~~~~----'------------------------'------------------------'
It) It) It)
~ ~ ~
::r: ::r: ::r:
P5 (20)
P6 (211
P7 (22)
P>O (13) (13) MSB P>O (3) (13)
p>o P>O P<O
P<O (14) P<O (14) P<O (2) P<O (14)
HORL--~----~~~ P<O
00 (Ill
01 (10)
02 02 (9)
03 03 (8)
04 04 (7)
05 05 (6)
os OS (5)
07 (4) 07 (4) 07 (4)
MSB
LSP MSP
> IS·BIT
TYPICALL Y 19 ns >
> 24·BIT
TYPICALL Y 24.4 ns :>
FIGURE 2
1283
2-662' TEXAS
INSTRUMENTS
TYPES SN54ALS1000A. SN54AS1000. SN74ALS1000A. SN74AS1000
QUADRUPLE 2·INP,",T POSITIVE·NAND BUFFERS/DRIVERS
• 'ALS 1 OOOA is a Buffer Version of SN54ALS1000A.SN54AS1000 •.. JPACKAGE

'ALSOOA SN74ALS1000A. SN74AS1000 •.. N PACKAGE
(TOP VIEW)
• 'AS 1000 is a Driver Version of 'ASOO
• 'AS1000 Offers High Capacitive Drive
Capability 1A VCC
1B 4B
• Package Options Include Both Plastic and 1Y 4A
Ceramic Chip Carriers in Addition to Plastic 2A 4Y
and Ceramic DIPs 2B 3B
Reliability GND 3Y
description
These devices contain four independent 2-input
NAND buffers/drivers. They perform the Boolean SN54ALS1000A. SN54AS1000 .•. FH PACKAGE
functions Y = A' B or Y = A. + B in positive logic. SN74ALS1000A. SN74AS1000 .•. FN PACKAGE
(TOP VIEW)
The SN54ALS 1 OOOA and SN54AS 1000 are char-
acterized for operation over the full military
temperature range of - 55°C to 125°C. The
SN~ 4ALS 1 OOOA and SN7 4AS 1000 are character-
ized for operation from a °C to 70 °C.
4A
NC
FUNCTION TABLE (each gate) 4Y
NC
INPUTS OUTPUT
3B
A B Y
H H L
L X H >-ou>-«
N22MM
X L H (!)
logic symbol
1A
1B
2A
2B
3A
3B
4A
4B
Copyright © 1982 by Texas InstrOments Incorporated

482
TEXAS 2-663
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1 OOOA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 1 25 °e
SN74ALS1000A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ooe~70oe
Storage temperature range ...... : ........ .' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °e to 150 °e

UNIT
..
V,K Vee = 4.5 V. 'I =
-18 rnA -1.5 -1.5 V
Vcc = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2
VOH Vce = 4.5 V. IO'H = -1 rnA 2.4 3.3 V
Vee = 4.5 V. IOH = -2.6 rnA 2.4 3.2
Vcc = 4.5 V. IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vec = 4.5 V. IOL = 24 rnA 0.35 0.5
»
r-
'I Vcc
Vce
= 5.5 V.
= 5.5 V.
V, = 7 V
V, = 2.7 V
0.1
20
0.1
20
rnA
/AA
en "H
I,L Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 rnA
»
2
lot
ICCH
Vcc = 5.5 V.
Vcc = 5.5 V.
Vo = 2.25 V
V, = 0 V
-30
0.86
-112
1.6
-30
0.86
-112
1.6
rnA
rnA
C ICCL Vcc = 5.5 V. VI = 4.5 V 4.8 7.8 4.8 7.8 rnA
t All typical values are at VCC = 5 V. TA = 25 ac.
l> tThe output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
en
(") switching characteristics (see Note 11
:lJ Vee = 4.5 V t~ 5.5 V.
(") CL = 50 pF.
c FROM TO RL = 500 Q.
=i PARAMETER
UNIT
MIN MAX MIN MAX
tpLH 2, 10 2 8
A orB Y ns
tpHL 2 10 2 7
1283
2-664- TEXAS
INSTRUMENlS
QUADRUPLE 2·INPUT POSITIVE·NAND DRIVERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS1 000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe
recommended operating conditions.

SN54AS1000 SN74AS1000
UNIT
TA Operating free-air temperature - 55 125 0 70 De
SN54AS1000 SN74AS1000
-18 rnA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. 10H = -2 rnA Vcc- 2 Vee- 2
Vee = 4.5 V. 10H = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40 rnA 2
Vee = 4.5 V. 10H = -48 rnA 2
Vee = 4.5 V, 10L = 40 rnA 0.25 0.5
VOL
Vee = 4.5 V. 10L = 48 rnA 0.35 0.5
V en
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA !::
IIH Vee = 5.5 V, VI = 2.7 V 20 20 Il A
:::>
IlL Vee =
5.5 V. VI = 0.4 V -0.5 -0.5 rnA· CJ
10:1: Vee = 5.5 V, Vo = 2.25 V -135 -135 rnA
a::
leeH Vee = 5.5 V, VI = 0 V 2.1 3.5 2.1 3.5 rnA CJ
leeL Vee = 5.5 V. VI = 4.5 V 11.5 19 11.5 19 rnA en
t All typical values are at Vee = 5 V, TA = 25 DC.
<t
C
switching characteristics (see Note 1) 2
Vcc = 4.5 V to 5.5 V.
<t
CL = 50 pF, en
..J
FROM TO RL = 500 Q,
PARAMETER
UNIT <t
SN54AS1000 SN74AS1000
MIN MAX MIN MAX
tpLH 1 4.5 1 3.5
A or B Y ns
tpHL 1 4.5 1 3.5
1283
TEXAS 2-665
INSTRUMENTS
2-666
• Quad Versions of 'ALSB05 SN54ALS1002A .•• J PACKAGE

• Buffer Version of 'ALS02 (TOP VIEW)
Ceramic Chip Carriers in Addition to Plastic VCC
and Ceramic DIPs 4Y
18 48
• Dependable Texas Instruments Quality and 4A
Reliability 3Y
28 38
description ~_ _--...-3A
buffers. They perform the Boolean functions
Y = A + B or Y = A' B in positive logic.
SN54ALS1002A ..• FH PACKAGE
The SN54ALS1 002A is characterized for operation
SN74ALS1002A ••• FN PACKAGE
(TOP VIEW)
125°C. The SN7 4ALS 1 002A is characterized for
U
operation from 0 °C to 70°C.
~~~~~
18 4 48
INPUTS OUTPUT . NC 5 NC
A B V 2Y 6 4A
H X L NC 7 NC
X H L 2A 8 3Y
L L H
COQU<!CO
NZZMM
logic symbol t9
(2)
lA ''It>
(3)
lB
(5)
2A
(6)
2B
(8)
3A
(9)
3B
(11)
4A
(12)
4B

1283
TEXAS 2-667
INSTRUMENTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AlS 1002A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74AlS1002A .............. ; . . . . . . . . . . . . . . . . . . 00eto70 0e

UNIT
TA Operating free-air temperature -55 125 a 70 DC
electrical characteristics over recommended operating free-air temperature range (u~less otherwise noted)
..
VIK Vce = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V, 10H =
-1 mA 2.4 3.3 V
Vee = 4.5 V. IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, 10L = 12 mA 0.25 0.4 0.25 0.4
VOL V
10L = 24 mA
»
r- II
Vee = 4.5 V.
Vee = 5.5 V, VI = 7 V 0.1
0.35 0.5
0.1 mA
IIH Vee = 5.5 V. VI=2.7V 20 20 /AA
CA
IlL Vec = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
»
2
10* Vec = 5.5 V.
Vec = 5.5 V.
Vo = 2.25 V
VI = OV
-30
1.7
-112
2.8
-30
1.7
-112
2~8
mA
mA
ICCH
C leCL Vec = 5.5 V. VI = 4.5 V 5.6 9 5.6 9 mA
»
u>
tAli typical values are at VCC = 5 V. TA = 25°C.
*The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS.
C") switching characteristics (see Note 11

:il
C")
Vee = 4.5 V to 5.5 V,
el = 50 pF,
c FROM TO Rl = 500 Q,
=i PARAMETER
UNIT
en SN54AlS1002A SN74AlS1002A
MIN MAX MIN MAX
tPLH 2 10 2 8
A or B Y ns
tpHL 2 10 2 7
NOTE 1. For load circuit and voltage waveforms. see page 1 12.
1283
2-668 TEXAS
INSTRUMENTS
• Buffer Version of ' ALS03A SN54ALS1003A ••• J PACKAGE

(TOP VIEW)
1B 4B
• Dependable Texas instruments Quality and
Reliability· 1Y 4A
2A 4Y
2B 3B
description
2Y 3A
These devices contain four independent 2-input GND 3Y
NAND buffers. They perform the Boolean functions
y = A' B or Y = A+ B in positive logic. The open-
collector outputs require. pull-up resistors to perform SN54ALS1003A •.. FH PACKAGE
correctly. They may be connected to other open- SN74ALS1003A ... FN PACKAGE
collector outputs to implement active-low wired-OR (TOP VIEW)
or active-high wired-AND functions. Open-collector U
ID<iUUID
devices are often used to generate higher VOH .......... z>-.t
levels.
The SN54ALSl 003A is characterized for operation 4A

over the full military temperature range of - 55°C to NC
1 25°C. The SN7 4ALS 1 003A is characterized for 4Y
operation from 0 °C to 70°C. NC
3B
fUNCTION TABLE (each gate)
INPUTS OUTPUT
A B y NC - No internal connection en
H H L t::
L X H ::l
X L H (.)
ex:
logic' symbol (.)
en
1A
<t:
18
2A
C
2
28
<t:
3A
38
en
..J
4A <t:
48

482
TEXAS 2-669
INSTRUMENTS
absolute maximum ratings over operating free-air temperature range (unless otherwise noted),
Supply voltage. Vee ............................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1003A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 1 25 °e
SN74ALS1003A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e

UNIT
-
VIK Vec = 4.5 V, II = -18 rnA -1.5 -1.5 V
IOH Vec = 4.5 V. VOH = 5.5 V 0.1 0.1 rnA
Vec = 4.5 V. IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL V
VCC = 4.5 V, 10l = 24 rnA 0.35 0.5
II VCC = 5.5 V, VI = 7 V 0.1 0.1 rnA
»
r- IIH VCC = 5.5 V, VI = 2.7 V 20 20 j./A
C/) IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
lecH Vee = 5.5 V, VI =aV 0.86 1.6 0.86 1.6 rnA
l> lecl Vee = 5.5 V, VI = 4.5 V 4.8 7.8 4.8 7.8 rnA
Z tAli typical values are at Vee = 5 v, TA = 25°e
C
en Vcc = 4.5 V to 5.5 V,
o CL = 50 pF,
::ll FROM TO RL = 680 Q

PARAMETER UNIT
c SN54ALS1003A SN74ALS1003A
=4 MIN MAX MIN MAX

en tplH
tpHL
A or B Y
10
2
40
18
10
2
33
12
ns
1283
2-670 TEXAS
INsrRuMENTS
HEX INVERTING DRIVERS
• 'AS 1004 Offers High Capacitive-Drive SN54ALS1004. SN54AS1004 ... J PACKAGE

Capability SN74ALS1004. SN74AS1004 ... N PACKAGE
(TOP VIEW)
• Driver Version of 'ALS04 and' AS04
1A VCC
and Ceramic DIPs 2Y 5A
• Dependable Texas Instruments Quality and 3A 5Y
Reliability 3Y 4A
description
These devices contain six independent inverting
drivers. They perform the Boolean function Y = A.
The SN54ALS1 004 and SN54AS1 004 are charac-
terized for operation over the full military temperature (TOP VIEW)
range of -55 D C to 125 D C. The SN74ALS1004
u
and SN74AS1004 are characterized for operation >-<!uu<!
from 0 DC to 70 DC.
........ z>co
2A BY
FUNCTION TABLE
(each inverter) NC NC
2Y 5A
INPUT OUTPUT NC NC
A Y 3A 5Y
H L
L H
C/)
logic symbol !::

::>
(J
1A
2A
a:
(J
3A
C/)
4A
SA «
6A c
z
Pin numbers shown are for J and N packages. «
en
-oJ
«

483
TEXAS 2-671
INSTRUMENTS
Supply voltage, Vee . . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS1004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00eto700e

UNIT
V,H High·level input voltage 2 2 V
V,L Low·level input voltage 0.8 0.8 V
V,K Vee = 4.5 V, "= -18 mA -1.5 -1.5 V
-
Vee = 4.5 V to 5.5 V. IOH = ':"0.4mA Vee- 2 Vee- 2
Vee = 4.5 V. IOH = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. IOH = -12 mA 2
Vee = 4.5 V. IOH = -15mA 2
Vee = 4.5 V. IOl = 12 mA
»
r-
VOL
Vee = 4.5 V. IOl = 24 mA
0.25 0.4 0.25
0.35
0.4
0.5
V
Vee = 5.5 V. V, = 7 V 0.1 0.1 mA

C/) "
Vee = 5.5 V. V, = 2.7 V 20 20 /J A
»
2
"H
',l
lot
Vee
Vee
= 5.5 V.
= 5.5 V.
V, = 0.4 V
Vo = 2.25 V -30
-0.1
-112 -30
-0.1
-112
mA
mA
o leeH Vee = 5.5 V. V, = 0 V 0.84 3 0.84 3 mA
»
C/)
leel
Vee = 5.5 V.
= 5 V. TA = 25°e.
V, = 4.5 V 7 12 7 12 mA
*The output conditions hava been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
,(,,)
ii
(")
Vcc = 4.5 V to 5.5 V.
c CL = 50 pF.
~ FROM TO RL = 500 Q.
en PARAMETER
UNIT
MIN MAX MIN MAX
tPlH 1 9 1 7
'A Y ns
tPHl 1 8 1 6
NOTE 1. For load CirCUit and voltage waveforms. see page 1-12.
1283
2-672 TEXAS
INSTRUMENTS
Supply voltage. Vee ............................................................... 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 1004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °C to 1 25 °e
SN74AS1 004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooe to 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 °C to 1 50 °e

SN54AS1004 SN74AS1004
UNIT
SN54AS1004 SN74AS1004
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
Vee = 4.5 V to 5.5 V. 10H = -2 mA Vee- 2 Vee- 2
Vee = 4.5 V. 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40mA 2
Vee = 4.5 V. 10H = -48 mA 2
Vee = 4.5 V. 10l = 40 mA 0.25 0.5
VOL V
Vee = 4.5 V. 10l = 48 mA 0.35 0.5
II Vee - 5.5 V. VI - 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7V 20 20 Ji.A
III Vee - 5.5 V. VI - 0.4 V -0.5 -0.5 mA
10* Vee = 5.5 V. Vo = 2.25 V -135 -135 mA
leeH Vee = 5.5 V. VI = OV 3.2 5 3.2 5 mA
leel Vee - 5.5 V. VI = 4.5 V 17.2 28 17.2 28 mA
tAli typical values are at Vee = 5 V. TA = 25°C.

Vcc = 4.5 V to 5.5 V.
Cl = 50 pF.
FROM TO Rl = 500 Q.
PARAMETER UNIT
SN54AS1004 SN74AS1004
MIN MAX MIN MAX
tplH 1 4.5 1 3.5
A or8 Y ns
tpHl 1 4.5 1 3.5
NOTE 1: For load circuit and voltage waveforms. see page '-12.
1283
TEXAS 2-673
INSlRUMENTS
- l>
r-
en
l>
:2
C
l>
en
(')
ii
(')
c
=i
en
2-674
HEX INVERTING BUFFERS WITH OPEN·COLLECTOR OUTPUTS
• Buffer Version of 'ALS05 SN54ALS1005 ... J PACKAGE

SN74ALS1005 ... N PACKAGE
(TOP VIEW)
1Y 6A
2A 6Y
Reliability
2Y 5A
3A 5Y
description
3Y 4A
These devices contain six independent inverting buf- GND 4Y
fers. They perform the Boolean function Y = A. The
open-collector outputs require pull-up resistors to
perform correctly. They may be connected to other
open-collector outputs to implement active-low SN54ALS1005 ... FH PACKAGE
wired-OR or active-high wired-AND functions. Open- SN74ALS1005 .•. FN PACKAGE
collector devices are often used to generate higher (TOP VIEW)
VOH levels.
u
The SN54ALS1005 is characterized for operation >- <I: U U <I:
.-2><0
over the full military temperature range of - 55 DC to
125 DC. The SN74ALS1005 is characterized for
operation from a DC to 70 DC. 2A 6Y
NC NC
FUNCTION TABLE (each inverter) 2Y 5A
NC NC
INPUT OUTPUT 3A 5Y
A Y
H L
L H
en
t:
NC- No internal connection ::J
logic symbol U
a:
lA U
2A
en
3A
<t
4A
C
SA
z
6A
<t
Pin numbers shown are for J and N packages. en
-I
<t

483
TEXAS 2-675
INSTRUMENlS
HEX INVERTING BUFFERS WITH OPEN·COLLECTOR OUTPUTS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage .. '. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........ 7 V
Operating free-air temperature range: SN54ALS1 005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS1005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . ' ...... 0 °C to 70°C

UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
10H Vee = 4.5 V, VOH = 5.5 V 0.1 0.1 mA
1m VOL
II
Vee
Vee
Vee
= 4.5 V,
= 4.5 V,
= 5.5 V,
IOL = 12 mA
IOL = 24 mA
VI = 7 V
0.25 0.4
0.1
0.25
0.35
0.4
0.5
0.1
V
mA
l> IIH Vee = 5.5 V, VI = 2.7V 20 20 /lA
r- IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
tJ)
leeH Vee = 5.5 V, VI = 0 V 0.9 3 0.9 3 mA
l> leeL Vee = 5.5 V, VI = 4.5 V 7 12 7 12 mA
:2 tAli tYPIcal values are at Vee = 5 v, TA = 25°e
C
tJ)
Vcc = 4.5 V to 5.5 V,
n CL = 50 pF,
::c PARAMETER
FROM TO RL = 680 Q,
UNIT
n (INPUT) (OUTPUT) TA = MIN to MAX
c SN54ALS1005 SN74ALS1005
=i
tJ) tpLH
MIN
5
MAX
35
MIN
5
MAX
30
A Y ns
tpHL 2 12 2 10
NOTE 1: For load CIrcUIt and voltage waveforms, see page 1-12.
1283
2-676 TEXAS
INSTRUMENTS
QUADRUPLE 2·INPUT POSITIVE·AND BUFFERS/DRIVERS
02661, DECEMBER 19B2-REVISED DECEMBER 19B3
SN54ALS1008A,SN54AS1008 ... JPACKAGE

• 'ALS100BA is a Buffer Version of ~ALSOB
SN74ALS1008A, SN74AS1008 ... N PACKAGE
• 'AS100B is a Driver Version of 'ASOB ITOPVIEW)
Q AS 1008 Offers High Capacitive Drive
I
1A VCC
Capability' 1B 4B
and Ceramic DIPs 2B 3B
2Y 3A
Reliability
description
SN54ALS1008A. SN54AS1008 ... FH PACKAGE
These devices contain four independent 2-input AND SN74ALS1008A. SN74AS1008 ... FN PACKAGE
buffers/drivers. They perform the Boolean functions ITOP VIEW)
Y = A'B or Y = A+B in positive logic.
U
The SN54AlS1008A and SN54AS1008 are char-
co «
.-.-Z>
U ',U co
'<3'
acterized for operation over the, full military

temperature range of - 55°C to 125°C. The
4A
SN7 4AlS 1 008A and SN7 4AS 1008 are character-
NC
2A 4Y
NC NC
FUNCTION TABLE 2B 3B
leach gate)
INPUTS OUTPUT
A B y
H H H
en
L X L
!::
X L L ::J
U
a:
logic symbol
U
lA &[>
(31
1y
en
18 <t
2A
(6) 2Y C
28 z
3A
(8) 3Y
<t
38 en
4A 1121 ...I
(11) 4Y
4B (131 <t

1282
TEXAS 2-677
INSTRUMENTS
TYPES SN54ALS100BA, SN74ALS100BA
QUADRUPLE 2·INPUT POSITIVE·AND BUFFERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1008A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 1 25°C
SN74ALS1008A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

UNIT
Vee Supply voltage 4.5 5 5.5 .4.5 5 5.5 V
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V, 10H = -0.4 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V, 10H = -1 rnA 2.4 3.3 V
III VOL
Vee
Vee
Vee
=
=
=
4.5 V,
4.5 V,
4.5 V,
10H = -2.6 rnA
10L = 12 rnA
10L = 24 rnA
0.25 0.4
2.4 3.2
0.35 0.5
V
»
r
II Vee - 5.5 V, VI = 7 V 0.1 0.1 rnA
Vee = 5.5 V, VI = 2.7V jJA
en IIH
IlL Vee = 5.5 V, VI = 0.4 V
20
-0.1
20
-0.1 rnA
»
:2
10* Vee
Vee
=
5.5 V,
=
5.5 V,
Vo = 2.25 V
VI = 4.5 V
-30
1.8
-112
3
-30
1.8
-112
3
rnA
rnA
leeH'
o leeL Vee - 5.5 V, VI = 0 V 5.7 9.3 5.7 9.3 rnA
»en tAli typical values are at Vee = 5 V, TA = 25 ae.
n switching characteristics (see Note 1)

JJ Vce = 4.5 V to 5.5 V,
n CL = 50 pF,
C FROM
"-
TO RL = 500 Q,
~ PARAMETER
UNIT
MIN MAX MIN MAX
tPLH 2 11 2 9
A or 8 Y ns
tpHL 3 11 3 9
1283
2-678 TEXAS
INSfRUMENTS
TYPES SN54AS100B, SN74AS100B
QUADRUPLE 2·INPUT POSITIVE·AND DRIVERS
Supply VOltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 1008 . . . . . . . . . . . . . ". . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74AS1008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe

SN54AS1008 SN74AS1008
UNIT
TA Operating free-air temperature -55 - 125 0 70 °e
SN54AS1008 SN74AS1008
VIK Vec = 4.5 V. II = -18 mA -1.2 -1.2 V
Vee = 4.5 V. 10H = -3mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40 mA 2
Vee = 4.5 V. 10H = -48 mA 2
Vee = 4.5 V. 10L = 40 mA 0.25 0.5
VOL
Vee = 4.5 V. 10L = 48 mA 0.35 0.5
V en
II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA
!::
= 5.5 V. VI = 2.7V :::>
IIH
IlL
Vee
Vee = 5.5 V. VI = 0.4 V
20
-0.5
20
-0.5
jJA
u
10* Vee = 5.5 V. Vo = 2.25 V -135 -135
mA
mA
a:
leeH Vee = 5.5 V. VI = 4.5 V 5.6 9.5 5.6 9.5 rnA u
leeL Vee = 5.5 V. VI = 0 V 13.5 22 13.5 22 mA en
tThe output conditions have been chosen to produce a c~rrent that closely approximates one half of the true short-circuit output current, lOS'
<t
C
Vcc = 4.5 V to 5.5 V.
<t
CL = 50 pF. en
-I
FROM TO RL = 500 Q,
PARAMETER
UNIT <t
SN54AS100B SN74AS1008
MIN MAX MIN MAX
tPLH 1 6 1 5
A or B Y ns
tPHL 1 6 1 5
1283
TEXAS 2-679
INSTRUMENTS
2-680
TRIPLE 3·INPUT POSITlVE·NAND BUFFERS
• Buffer Version of 'ALS10 SN54ALS1010A .•. J PACKAGE

and Ceramic DIPs
VCC
• Dependable Texas Instruments Quality and lC
Reliability lY
3C
description 3B
These devices contain three independent 3-input 3A
NAND buffers. They perform the Boolean functions -t..._---=--t-"3Y
y = A·B·C or Y = A+B+C in positive logic.
The SN54ALS 101 OA is characterized for operation
125°C. The SN74ALS10l0A is characterized for
operation from 0 °C to 70°C. SN54ALS1010A •.• FH PACKAGE
SN74ALS1010A ••• FN PACKAGE
(TOP VIEW)
INPUTS OUTPUT
u
CD ~ U uu
A B C y z> ....
H H H L
L X X H 2A lY
X L X H NC NC
X X L H 2B 3C
NC NC
logic symbol 2C 3B CI)
1A
(11 &[>
!::
::J
1B
U
1C NC - No internal connection a:
2A U
28
CI)
2C
<t
3A
38
C
(111 2
3C
<t
CI)
..J
<t'

482
TEXAS 2-681
INSTRUMENTS
TRIPLE 3·INPUT POSITIVE·NAND BUFFERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 01 OA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS1010A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe

UNIT
VIK Vee = 4.5 V. 11,= -18 rnA -1.5 - -1.5 V
Vee - 4.5 V to 5.5 V, IOH - -0.4 rnA Vee- 2 Vee- 2
VOH "Vee - 4.5 V, IOH = -1 rnA 2.4 3.3 V
lEI VOL
Vee = 4.5 V,
Vee - 4.5 V.
Vee = 4.5 V,
IOH = -2.6 rnA
IOL = 12 rnA
IOL = 24 rnA
0.25 0.4
2.4 3.2
0.25
0.35
0.4
0.5
V
»
r-
II Vee - 5.5 V, VI - 7 V
= 2.7
0.1 0.1 rnA
(J) IIH Vee = 5.5 V. VI V 20 20 /J A

IlL Vee - 5.5 V, VI - 0.4 V -0.1 -0.1 rnA
»
:2
IO~ Vee = 5.5 V.
Vee = 5.5 V,
Vo = 2.25 V
VI = 0 V
-30
0.65
-112
1.2
-30
0.65
-112
1.2
rnA
rnA
leeH
o leeL Vee - 5.5 V, VI - 4.5 V 3.6 5.8 3.6 5.8 rnA
»
(J)
*The output conditions have been chosen to produce a current that closely approxfmates one half of the true short-circuit output current. lOS'

::D Vcc = 4.5 V to 5.5 V.
(")
Cl = 50 pF,
c FROM TO Rl = 500 Q,
=t
(J)
PARAMETER
UNIT
MIN MAX MIN MAX
tPLH 2 10 2 8
Any Y ns
tpHL 2 10 2 7
NOT~ 1: For load circuit and voltage waveforms. see page 1-12.
1283
2-682 TEXAS
INSTRUMENTS
TRIPLE 3·INPUT POSITIVE·AND BUFFERS
• Buffer Version of 'ALS11 SN54ALS1011A . ~. J PACKAGE

SN74ALS1011A .•. N PACKAGE
(TOP VIEW)
Ceramic Chip Carriors in Addition to Plastic
and Ceramic DIPs VCC
1C
• Dependable Texas Instruments Quality and 1Y
Reliability
3C
3B
d,escription 3A
These devices contain three independent 3-input 3Y
AND buffers. They perform the Boolean functions
Y = A·B·C or Y = A+B+C in positive logic.
SN54ALS1011A •.• FH PACKAGE
The SN 54ALS 1011 A is characterized for operation
SN74ALS1011A ••. FN PACKAGE
over the full military temperature range of -'55°C to
(TOP VIEW)
125°C. The SN74ALS1 011 A is characterized for
U
operation from 0 °C to 70°C. al<{U UU
z>.-
FUNCTION TABLE (each gate) 2A 1Y

NC NC
INPUTS OUTPUT
2B 3C
A B C y
NC NC
H H H H
2C 38
L X X L
X L X L
X X L L >-ou>-<{
NZZMM
(!)
NC - No internal connection CJ)

logic symbol
(1)
!::
lA &[> ::)
18
(2) (12)
lY u
lC
a:
2A U
(6)
28 2Y CJ)
2C <t
3A
o
38
(8)
3Y z
3C
(11)
<t
CJ)
..J
<t

~82
TEXAS 2-683
INSTRUMENTS
TRIPLE 3·INPUT POSITIVE·AND BUFFERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 011 A ............. _. . . . . . . . . . . . . . . . - 55°C to 125°C
SN74ALS1 011 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . ~ . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50°C

UNIT
10L Low-level output current 12 .24 mA
VIK Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. 10H = -0.4 mA Vee- 2 Vee- 2
VOH Vee = 4.5
V. 10H =
-1 mA 2.4 3.3 V
IB VOL
Vee = 4.5 V.
Vee = 4.5 V.
Vee = 4.5 V.
10H
10L
=
-2.6 mA
10L = 12 mA
= 24 mA
0.25 0.4
2.4 3.2
0.25
0.35
0.4
0.5
V
l> II Vee = 5.5 V. VI =7V 0.1 0.1 mA
r- IIH Vee = 5.5 V. VI = 2.7V 20 20 jAA
(/)
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
l> 10* Vee = 5.5 V. Va = 2.25 V -30 -112 -30 -112 mA
2 ICCH VCC = 5.5 V. VI = 4.5 V 1.4 2.3 1.4 2.3 mA
C leeL Vee = 5.5 V. VI = OV 4.3 7 4.3 7 mA
l> t All typical values are at Vee = 5 V. TA = 25°e.
(/) ;The output conditions hava been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'

:u Vcc = 4.5 V to 5.5 V.
(')
c FROM TO
CL = 50 pF.
RL = 500 Q.
/
=i
(/)
PARAMETER
UNIT
MIN MAX MIN MAX
tpLH 2 12 2 10
Any Y ns
tpHL 3 11 3 9
1283
2-684 TEXAS
INSTRUMENTS
TYPES SN54ALS1020A. SN74ALS1D2DA
D2661.'APRIL 1982-REVISED DECEMBER 1983
• Buffer Version of ' ALS20A SN54ALS1020A .•• J PACKAGE

and Ceramic DIPs
1A 1U14 VCC
• Dependable Texas Instruments Quality and 18 2 13 2D
Reliability NC ,-3 12 2C
1C 4 11 NC
description 1D 5 10 28
1Y 6 9 2A
These devices contain two independent 4-input sF
GND 7 2Y
NAND buffers. They perform the Boolean functions
Y = A·B·C·D or Y = A+B+C+D in positive logic.
The SN54ALS 1 020A is characterized for operation SN54ALS1020A ••. FH PACKAGE
over the full military temperature range of - 55 °C to SN74ALS1020A ••• FN PACKAGE
1 25 °C. The SN7 4ALS 1020A is characterized for (TOP VIEW)
operation from ooC to 70 oC. U
m«UUQ
"-"-Z>N

4 2C
INPUTS OUTPUT 5 NC
A B C 0 y 6 NC
H H H H l 7
l X X X H 1D 8
X l X X H
X X l X H
X X X l H
en
logic symbol NC-No internal connection
!::
11) &
::l
1A
U
1B
(2)
lY
a:
(4)
1C
(5)
U
10
(9)
en
2A
(10)
<t
2B
112) 2Y C
2C
(13) z
20
<t
~
<t

182
TEXAS 2-685
INSTRUMENTS
Supply voltage, Vcc ............................. '.' ................................ 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 020A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
- SN74ALS1020A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 00Cto700C

UNIT
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
VOH Vee = 4.5 V, IOH = -1 mA 2.4 3.3 V
Vee = 4.5 V, IOH = -2.6 mA 2.4 3.2
Vee = 4.5 V, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V, IOL = 24 mA 0.35 0.5 .
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V, VI = 2.7V 20 20 /-LA
IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 mA
lo~ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
leeH Vee = 5.5 V, VI = 0 V 0.5 0.8 0.5 0.8 mA
leeL Vee = 5.5 V, VI = 4.5 V 2.4 3.9 2.4 3.9 mA
.tAII typical values are at Vee = 5 V, TA = 25°e.

VCC = 4.5 V to 5.5 V.
CL = 50 pF,
FROM. TO RL = 500 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 2 10 2 8
Any y ns
tpHL 2 10 2 7
1283
2-686 TEXAS
INsrRUMENTS
QUADRUPLE 2·INPUT POSITIVE·OR BUFFERS/DRIVERS
• 'ALS1032A is a Buffer Version of 'ALS32 SN54ALS1032A. SN54AS1032 •.• J PACKAGE

SN74ALS1032A. SN74AS1032 ••. N PACKAGE
• 'AS1032 is a Driver Version of 'AS32
ITOPVIEW)
o 'AS 1032 Offers High Capacitivo Drivo
Capability
VCC
• Package Options Include Both Plastic and 1B 4B
Ceramic Chip Carriers in Addition to Plastic 1Y 4A
and Ceramic DIPs 2A 4Y
• Dependable Texas Instruments Quality and 2B 3B
Reliability 2Y 3A
GND 3Y
description
These devices contain four independent 2-input OR
buffers/drivers. They perform the Boolean functions SN54ALS1032A. SN54AS1032 ... FH PACKAGE
Y = A + B or Y = A.. B in positive logic. SN74ALS1032A. SN74AS1032 ... FN PACKAGE
ITOPVIEW)
The SN54ALS 1032A and SN54AS 1032 are char-
acterized for operation over the full military U
m<l:UUm
temperature range of - 55 DC to 125 DC. The .-.-Z>-t
SN7 4ALS 1 032A and SN7 4AS 1032 are character-
ized for operation from 0 DC to 70 DC.
1Y 4A
NC NC
FUNCTION TABLE 2A 4Y
leach gate) NC NC
2B 3B
INPUTS OUTPUT
A B Y
H X H >-OU>-<l: en
X H H
NZZMM
(!) t::
L L L ::::>
u
logic symbol
NC-ND internal connection
a::
u
lA
III ;;'1[> en
«
131 1y
121
18
2A
141
161
2y c
28
lSI
z
3A
191
1101
181 3Y «
38
1121
en
...J
4A
48
1131
1111 4y
«

1282
TEXAS 2-687
INSTRUMENTS
QUADRUPLE 2·INPUT POSITIVE·OR BUFFERS
Input voltage . . . . . . . . . . . . . . . . ~ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 032A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..: 55 De to 125 De
SN74ALS1032A . . . . . . . . . . . . . . . . . . . . . . . . . . . . : .... ODeto70 De
Storage temperature range . . . . . . . . . . . . . . . . . . . ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 De to 1 50 De

UNIT
MIN NOM MAX MIN NOM 'MAX
..
VIK Vee = 4.5 V. II = -18 rnA -1.5 -1.5 V
Vee = 4.5 V to 5.5 V. IOH = -0.4 rnA Vee- 2 Vee- 2
VOH Vee = 4.5 V. IOH = -1 rnA 2.4 3.3 V
Vee = 4.5 V. IOH = -2.6 rnA 2.4 3.2
Vee = 4.5 V. IOL = 12 rnA 0.25 0.4 0.25 0.4
VOL V
Vee = 4.5 V. IOL = 24 rnA 0.35 0.5
»
r-
II Vee = 5.5 V.
= 5.5 V.
VI = 7 V
VI = 2.7 V
0.1 0.1 rnA
en IIH
IlL
Vee
Vee = 5.5 V, VI = 0.4 V -0.1
20 20
-0.1
jAA
rnA
»
:2
10*
leeH
Vee
Vee
= 5.5 V.
= 5.5 V.
. Vo = 2.25 V
VI = 4.5 V
-30
2.5
-112
5
-30
2.5
-112
5
rnA
rnA
o leeL Vee = 5.5 V. VI = 0 V 6.6 10.6 6.6 10.6 rnA
»
en
t All typical values are at Vee = 5 V. TA = 25°C.
o switching characteristics (see Note 1) ,

:0 Vcc = 4.5 V to 5.5 V.
o CL = 50 pF.
c FROM TO RL = 500 Q.
=i PARAMETER
UNIT
MIN MAX MIN MAX
tPLH 2 12 2 9
A or B Y ns
tpHL 3 15 3' 12
1283
2-688 TEXAS
INSTRUMENTS
QUADRUPLE 2-INPUT POSITIVE-OR DRIVERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS1 032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AS1032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ooe to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to 1 50 °e '
recommended oporating conditions

SN54AS1032 SN74AS1032
UNIT
electrical characteristics over recommended Operating free-air temperature range (unless otherwise noted)
SN54AS1032 SN74AS1032
VIK Vee = 4.5 V. II = -18 mA -1.2 -1.2 V
Vee = 4.5 V. 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -40 mA 2
Vee = 4.5 V. 10H = -48 mA 2
Vee = 4.5 V. 10L = 40 mA 0.25 0.5
VOL
Vee = 4.5 V. 10L = 48 mA 0.35 0.5
V en
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA t::
IIH Vee = 5.5 V, VI = 2.7 V 20 20 ,..A
::J
()
= 5.5 V. VI = 0.9 V
IlL
10*
Vee
Vee = 5.5 V. Vo = 2.25 V -135
-0.5
-135
-0.5 mA
mA
a:
leeH Vee = 5.5 V. VI = 4.5 V 7.7 11.5 7.7 11.5 mA
()
leeL Vee = 5.5 V. VI = OV 14.7 24 14.7 24 mA en
*The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current. lOS.
«
c
Vcc = 4.5 V to 5.5 V.
«
CL = 50 pF. en
~
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL = 500 Q.
TA = MIN to MAX
UNIT «
SN54AS1032 SN74AS1032
MIN MAX MIN MAX
tpLH 1 7 1 5.5
A or B V ns
tPHL 1 6.5 1 5.5
1283
TEXAS 2-689
INSTRUMENTS
2-690
HEX DRIVERS
• ' AS 1034 Offers High Capacitive-Drive SN54ALS1034. SN54AS1034 ... J PACKAGE

Capability SN74ALS1034. SN74AS1034 ... N PACKAGE
ITOPVIEW)
• Nonlnvertlng Drivers
• Package Options Include Both Plastic and 1A Vce
Ceramic Chip Carriers In Addition to Plastic 1Y 6A
and Ceramic DIPs 2A 6Y
Reliability . 3A 5Y
3Y 4A
description GND 4Y
These devices contain six independent noninverting

drivers. They perform the Boolean function Y = A.
The SN54ALS 1034 and SN54AS 1034 are charac- SN54ALS1034. SN54AS1034 ... FH PACKAGE
terized for operation over the full military temperature SN74ALS1034. SN74AS1034 ... FN PACKAGE
range of - 55°C to 125°C. The SN74ALS1034 (TOP VIEW)
and SN7 4AS 1034 are characterized for operation U
from 0 °C to 70°C.
>-«U U«
z > to
FUNCTION TABLE (each buffer) 6Y

NC NC
INPUT OUTPUT 2Y 5A
A Y NC NC
H H 3A 5Y
L L
logic symbol
en
!:::
1A ::J
U
2A
3A
NC-No internal connection a:
4A
U
en
5A
6A
«
c
Pin numbers shown are for J and N packages. z
«
en
...J
«

482
TEXAS 2-691
-INSTRUMENTS
HEX DRIVERS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1034 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 1 25 °e
SN7 4ALS 1034 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °e to 70 °e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 °e to 150 0 e

UNIT
10H High-level output curent -12 -15 rnA
MIN· TVPt MAX MIN TVpt MAX
VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
Vee = 4.5 =
IIIfJ
V to 5.5 V, 10H -0.4 rnA Vee- 2 Vee- 2
Vee = 4.5 V, 10H = -3 rnA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V. 10H = -12 rnA 2
l> Vee = 4.5 V. 10H = -15 rnA 2
r- Vee = 4.5 V. 10L = 12 rnA 0.25 0.4
m VOL
Vee = 4.5 V. 10L = 24 rnA 0.35 0.5
V
l> II Vee = 5.5 V. VI = 7 V 0.1 0.1 rnA

:2 IIH Vee = l5.5 V. VI = 2.7 V 20 20 JlA
C IlL Vee = 5.5 V, VI = 0.4 V -0.1 -0.1 rnA
= Vo = 2.25 V
l> 10* Vee 5.5 V. -30 -112 -30 -112 rnA
m leeH Vee
Vee
=
=
5.5 V.
5.5 V.
VI = 4.5 V
VI = 0 V
3
8
6
14
3
8
6
14
rnA
rnA
n leeL
5; t All typical values are at Vee = 5 V. T A = 25°e. '
n *The output conditions have been chosen to produce a current that closely approximates one half of 'the true short·circuit output current. lOS'
c:
=t
m
Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 500 Q,
PARAMETER UNIT
(lNPUTI (OUTPUT) TA = MIN to MAX
MIN MAX MIN MAX
tpLH 1 10 1 8
A V .ns
tpHL 1 10 1 .8
1283
2-692 TEXAS
INSTRUMENTS
HEX DRIVERS
Supply voltage, V CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . . . . 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS 1034 : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to 125°C
SN74AS1034 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC

SN54AS1034 SN74AS1034
UNIT
SN54AS1034 SN74AS1034
MIN TYpt MAX MIN TYpt MAX
-18 mA -1.2 -1.2 V
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V
Vee = 4.5 V, 10H = -40 mA 2
Vee = 4.5 V, 10H = -48 mA 2
Vee = 4.5 V. 10L = 40 mA 0.25 0.5
VOL
Vee = 4.5 "I, 10L = 48 mA 0.35 0.5
V en
II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA t:
IIH Vee = 5.5 V, VI = 2.7V 20 20 Il A
::::>
IlL Vee = 5.5 V, VI = 0.4 V -0.5 -0.5 mA u
10+ Vee = 5.5 V. Vo = 2.25 V -135 -135 mA
a::
leeH Vee = 5.5 V, VI =0 V 8.5 14 8.5 14 mA u
leeL Vee = 5.5 V. VI = 4.5 V 20 33 20 33 mA en
tAli typic~1 values are at Vee = 5 V. TA = 25°e.
;The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
<t
C
switching characteristics (see Note 1) Z
Vcc = 4.5 V to 5.5 V,
<t
CL = 50 pF, en
FROM TO RL = 500 Q,
...J
PARAMETER
UNIT <t
SN54AS1034 SN74AS1034
MIN MAX MIN MAX
tpLH 1 6 1 5
A Y tis
tpHL 1 6 1 5
1283
TEXAS 2-693
INSTRUMENTS
2-694
HEX NONINVERTING BUFFERS WITH OPEN-COLLECTOR OUTPUTS
• Noninverting Buffers with Open-Collector Outputs

• Package Options Include Both Plastic and Ceramic SN54ALS1035 ... JPACKAGE
Chip Carriers in Addition to Plastic and Ceramic DIPs SN74ALS1035 ... N PACKAGE
(TOP VIEW)
lA VCC
description lY 6A
These devices contain six independent non inverting buffers. 2A 6Y
They perform the boolean functions Y = A. The open-collector 2Y 5A
outputs require pull-up resistors to perform correctly. They IT!ay 3A 5Y
be connected to other open-collector outputs to implement 3Y 4A
active-low wired-OR or active-high wired-AND functions. Open- GND 4Y
collector devices are often used to generate higher VOH levels.
The SN54ALS 1035 is characterized for operation over the full

military temperature range of - 55°C to 125°C. The
SN74ALS1035 is characterized for operation from a °C to
70°C.
FUNCTION TABLE (each bufferl

INPUT OUTPUT SN74ALS1035 ... FN PACKAGE
A Y (TOP VIEW)
H H u
L L >-«UU«
... z>(o
en
6Y
t:::
2A
:::>
logic symbol
NC NC
u
2Y 5A a:
NC NC
3A 5Y
U
1A en
2A
<t
3A o
4A z
SA
NC-No internal connection <t
6A en
..J
<t

1283
TEXAS 2-695
INSTRUMENTS
HEX NONINVERTING BUFFERS WITH OPEN·COLLECTOR OUTPUTS
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .' ....... 7 V

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS1 035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 °e to 125 °e
SN74ALS1035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OOeto70oe

UNIT
16 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
»
r-
MIN
SN54ALS1035
Typt MAX
SN74AlS1035
MIN Typt MAX
UNIT
en VIK Vee = 4.5 V, II = -18 rnA -1.5 -1.5 V
»
:2
IOH
VOL
Vee = 4.5
Vee = 4.5 V,
V, VOH = 5.5 V
IOL = 12 rnA 0.25
0.1
0.4 0.25
0.1
0.4
rnA
V
C Vee = 4.5 V, IOL = 24 rnA 0.35 0.5
II Vee - 5.5 V, VI - 7 V 0.1 0.1 rnA
»
en
IIH Vee - 5.5 V, VI - 2.7V 20 20
-0.1
/J A
rnA
IlL Vee - 5.5 V, VI - 0.4 V -0.1
Q leeH Vee - 5.5 V,

Vee = 5.5 V,
VI = 4.5 V
VI = 0 V
3 6 3 6 rnA
rnA
leeL 8 14 8 14
::Il
(") tAli typical values are at Vee = 5 V, TA = 25°e.
c
=4 switching characteristics (see Note 1)
en
Vcc = 4.5 V to 5.5 V,
Cl = 50 pF,
FROM TO RL = 680 Q,
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 5 35 5 30
A Y ns
tpHL 2 14 2 12
1283
2-696 TEXAS
INSTRUMENTS
QUADRUPLE 2·INPUT POSITIVE·NOR DRIVERS
• Quad Versions of AS805A SN54AS1036 ••. J PACKAGE

SN74AS1036 •.• N PACKAGE
• Offers High Capacitive·Drive Capability (TOP VIEW)
VCC
1B 4B
and Ceramic DIPs 1Y 4A
• Dependable Texas Instruments Quality and 4Y
Reliability 2B 3B
2Y 3A
description GND 3Y

drivers. They perform the Boolean functions
Y = A+B or Y = A'S in positive logic.
SN54AS1036 ..• FH PACKAGE
The SN54AS 1036 is characterized for operation
SN74AS1016 ••• FN PACKAGE
(TOP VIEW)
125°C. The SN74AS1036 is characterized for
operation from 0 °C to 70°C. U
al«U Ual
.-Z>~

1Y 4A
INPUTS OUTPUT NC NC
A B Y 2A 4Y
H X L NC NC
X H L 2B 3B
L L H
>-OU>-«
NZZC")C")
en
logic symbol (!) !::
NC - No internal connection :::>
lA
u
1B a:
2A
U
2B
en
3A
3B
«
4A
c
2
4B
«
...J
«
TEXAS 2-697
INsrRUMENlS
QUADRUPLE 2·INPUT POSITIVE·NOR DRIVERS
Input voltage' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54AS1 036 . . . . . . . . . . . . . . . . . . . . . . . . . ."..... - 55 DC to 125 DC
SN74AS1036 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODCto70 DC
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : ........ - 65 DC to 1 50 DC

SN54AS1036 SN74AS1036
UNIT
IOL Low-level output 'current 40 48 rnA
SN54AS1036 SN74AS1036
VIK Vee = 4.5 V, II = -18 rnA -1.2 -1.2 V
Vee = 4.5~, IOH = -3 rnA 2.4 3.2 2.4 3.2
1m VOH V
Vee = 4.5 V, 10H = -40 rnA 2
Vee = 4.5 V, 10H = -48 rnA 2
»
r-
VOL
Vee = 4.5 V,
Vee = 4.5 V,
10L = 40 rnA
10L = 48 rnA
0.25 0.5
0.35 0.5
V
t/) II Vee =5.5 V, VI = 7 V 0.1 0.1 rnA
»
2
IIH
IlL
Vee = 5.5 V,
Vee = 5.5 V,
VI = 2.7V
VI = 0.9 V
20
-0.5
20
-0.5
/AA
rnA
10* Vee = 5.5 V, Va = 2.25 V -135 -135 rnA
C leeH Vee = 5.5 V, VI = 0 V 4.3 7 4.3 7 rnA
»
t/)
leeL Vee = 5.5 V,
VI = 4.5 V 14 23 14 23 rnA
;The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
Q
:D switching characteristics (see Note 1)
(')
c VCC = 4.6 V to 6.6 V.
CL = 60 pF.
=t
t/) PARAMETER
FROM TO RL = 600 Q.
UNIT
SN54AS1036 SN74AS1036
MIN MAX MIN MAX
tPLH 1 4.5 1 4
A or B Y ns
tpHL 1 4.5 1 4
1283
2-698 TEXAS
INSTRUMENTS
TYPES SN54ALS1240, SN54ALS1241, SN74ALS1240, SN74ALS1241'
• Low-Power Version of 'ALS240 and 'ALS241 SN54ALS1240, SN54ALS1241 ..• J PACKAGE

SN74ALS1240, SN74ALS1241 ... N PACKAGE
• 3-State Outputs Drive Bus Lines or Buffer (TOP VIEW)
Memory Address Registers
1G VCC
• P-N-P Inputs Reduce DC Loading 1A 1 2G/2Gt
• Dependable Texas Instruments Quality and 2Y4 1Y1
Reliability 1A2 2A4
2Y3 1Y2
description 1A3 2A3
2Y2 1Y3
These octal buffers and line drivers are designed specif-
1A4 2A2
ically to improve both the performance and density of
2Y1 1Y4
three-state memory address drivers, clock drivers, and bus-
GND 2Al
oriented receivers and transmitters. The designer has a
choice of selected combinations of inverting and non-
inverting outputs, symmetrical G (active-low output SN54ALS1240, SN54ALS1241 .•. FH PACKAGE
control) inputs, and complementary G and G inputs. These SN74ALS1240, SN74ALS1241 •.. FN PACKAGE
devices feature high fan-out and improved fan-in. (TOP VIEW)
+-
C!.l
The -1 versions of the SN64ALS' parts are identical to the .;t.... U~
standard versions except that the recommended maximum >- ~ 1C!.l UIC!.l
N .... >N
IOL is increased to 24 milliamperes. There are no -1 versions
of the SN54ALS' parts.
lA2 4 1Y1
The SN54ALS1240 and SN54ALS1241 are characterized 2Y3 2A4
for operation over the full military temperature range of 1A3 6 1Y2
- 55°C to 125°C, The SN74ALS1240 and SN74ALS1241 2Y2 7 2A3
are characterized for operation from ooC to 70°C. 1A4 8 1Y3
9 10 111213
en
!::
::>
()
t2G for 'ALS1240 or 2G for 'ALS1241 a:
()
en
«
c
z
«
en
..J
«

ThIs document contains Infonnatlon on a product under
davalopment. Taxaslnltrumantl reserval the right to
change or discontinue this product without notica.
TEXAS 2-699
INSTRUMENTS
logic symbols
'ALS1240 'ALS1241
1Y1
1Y2
1Y3
1Y4
2~
2A1 2Y1 2A1 2Y1

2A2 2Y2 2A2 2Y2
.2A3 2Y3 2A3 2Y3
2A4 2Y4 2A4 2Y4
'ALS1240 'ALS1241
IIfI
l> (18) (2)
r- 1A1 (2) 1Y1 1A1
(18) 1Y1
en
(16) (4) (16)
l> 1A2 (4) 1Y2 1A2 1Y2
;2
C 1A3 (6) (14)
1Y3 1A3
(6) (14)
1X3
l>
en 1A4 (8)
(12)
1Y4 1A4
(8) (12) 1Y4
Q
:JJ 2G
(")
c 2A1 (11) (9) 2Y1 (11) (9)
=t
en
2A1 2Y1
(13) (7) 2Y2 (13) (7)

2A2 2A2 2Y2
(15) (5) 2Y3 (15) (5)

2A3 2A3 2Y3
(17) (3) (17) (3)

2A4 2Y4 2A4 2Y4
1283
2-700 TEXAS
INSTRUMENTS

Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1240, SN54ALS 1241 . . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74ALS1240,SN74ALS1241 . . . . . . . . . . . . . . . . . . . . . OOet070oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . '. . . . . . . . . . . . . . . . . . . . . . . ',' . .. - 65°C to 1 50 °e

8 16
24t
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) CJ)
SN54ALS1240 SN74ALS1240 !::

PARAMETER TEST CONDITIONS SN 54ALS 1241 SN74ALS1241 UNIT ::>
MIN TYP~ MAX MIN TYP~ MAX u
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V a:
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 3 Vee- 2 u
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
VOH V CJ)
Vee = 4.5 V, 10H = -12 mA 2
Vee = 4.5 V, 10H = -15 mA 2
<t
Vee = 4.5 V, 10L = 8 mA 0.25 0.4 0.25 0.4 C
VOL Vee = 4.5 V, 10L = 16 mA
0.35 0.5
V z
(lOL = 24 mA for - 1 versions) <t
10ZH Vee = 5.5 V, Vo = 2.7 V 20 20 /LA CJ)
10ZL Vee = 5.5 V, VI = 0.4 V -20 -20 /LA ..J
II Vee = 5.5 V, VI = 7 V 0.1 0.1 mA <t
IIH Vee = 5.5 V, VI = 2.7V 20 20 /LA
IlL Vee = 5.5 V. VI= 0.4 V -0.1 -0.1 mA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
l Outputs high 6.5 6.5
lee Vee = 5.5 V I Outputs low 10 10 mA
t All typical values are at Vee = 5 V, TA = 25 ae.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short·circuit output current, lOS'
1283
TEXAS 2-701
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
tpLH 9 9
A Y ns
tPHL 9 9
tpZH 17 17
~
G Y
19 19
ns
tpZL
tpHZ 7 7
G Y
6 6
ns
tpLZ
,ALS 1241 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
MIN TypT MAX MIN TypT MAX
tpLH 9 9
A Y ns
tpHL 9 9
tpZH 17 17
G or G Y
19 19
ns
tpZL
tpHZ 7 7
G orG Y
6 6
ns
tPLZ
t All typical values are at VCC = 5 V. TA = 25 DC.

1283
2-702 TEXAS
INSTRUMENTS
TYPES SN54ALS1242, SN54ALS1243,
QUADRUPLE BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
D2661. DECEMBER 1982-REVISED DECEMBER 1983
• 2-Way Asynchronous Communication between Data SN54ALS1242,SN54ALS1243 . J PACKAGE

Buses SN74ALS1242,SN74ALS1243 ; N PACKAGE
(TOP VIEW)
• P-N-P Inputs Reduce DC Loading
• Low-Power Version of 'ALS242, and 'ALS243
GAB VCC
• Three-State Outputs NC GBA
• Package Options Include Both Plastic and Ceramic A1 NC
Chip Carriers in Addition to Plastic and Ceramic DIPs A2 B1
A3 B2
• Dependable Texas Instruments Quality and Reliability A4 B3
GND B4
description
These quadruple bus transceivers are designed for two-way
communication between data buses. The control function
implementation allows for maximum flexibility in timing.
These devices allow data transmission from the A bus to the B

bus or from the B bus to the A bus depending upon the logic
levels at the enable inputs (GBA and GAB). SN54ALS1242,SN54ALS1243 FH PACKAGE
SN74ALS1242,SN74ALS1243 FN PACKAGE
The enable inputs can be used to disable the device so that the
(TOP VIEW)
buses are effectively isolated.
The dual-enable configuration gives the ' ALS 1242 and

,ALS 1 243 the capability to store data by simultaneous enabling
of GAB and GBA. Each output reinforces its input in this
transceiver configuration. Thus, when both control inputs are
enabled and all other data sources to the two sets of bus lines are
at high impedance, both sets of bus lines (8 in all) will remain at
NC
NC
011
en
their last states. The 4-bit codes appearing on the two sets of
buses will be complementary for the' ALS 1 242 or identical for
B1
NC
t::
::J
the 'ALS1243. B2 U
The -1 versions of the SN74ALS' parts are identical to the a:
standard versions except that the recommended maximum IOL is U
increased to 24 milliamperes. There are no -1 versions of the en
SN54ALS' parts.
«
The SN54ALS1242 and SN54ALS1243 are characterized for 0
operation over the full military temperature range of - 55 °C to 2:
125°C. The SN74ALS1242 and SN74ALS1243 are
characterized for operation from 0 °C to 70 o C.
«
en
...J
FUNCTION TABLE «
GAB GBA 'ALS1242 'ALS1243
L L Ato B A to B
H H B to A B to A
Latch A and B Latch A and B
L H
(A = B) (A = B)
PRODUCT PREVIEW Copyright © 1982 by Texas Instruments Incorporated.

1283
ThIa document contaJna information on • product under
development. Tex.slnstruments reserve. the right to - TEXAS 2-703
INSTRUMENlS
logic symbols logic diagrams (positive logic)
'ALS1242
'ALS1242
(13)
GBA
(1 )
GAB
(31 (11 )
Al Bl
A2 (4) (10) B2
(4)
A2 B2
(51 (9) A3 (5) (9) B3

A3 B3
(61 (8)
A4 B4
A4 (6) (8) B4
~
l>
r-
(A
'ALS1243
l> 'ALS1243
2
C
l>
(A Al Bl
~
A2 (4) (10) B2
::a A2 B2
0
C A3 B3
A3 (5) (9) 83
=i
en A4 B4
A4 (6) (8) 84
1283
2-704 TEXAS
INSTRUMENTS .
1/0 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS1242, SN54ALS 1243. . . . . . . . . . . . . . . . .. - 55°e to 125 °e
SN74ALS1242, SN74ALS1243 ..................... Doe to 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . .' . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 °e to 150 °e

8 16
24t
Vee = 4.5 V, II = -18 mA

MIN TYP:l: MAX
-1.5
MIN TYP:l: MAX
-1.5 V
en
VIK
Vee = 4:15 V to 5.5 V, 10H = -0.4 mA Vee- 2 vee- 2
!::
:::>
VOH
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
,v u
Vee = 4.5 V, 10H = -12 mA 2
a:
10H = -15 mA 2
Vee = 4.5 V,
Vee = 4.5 V, 10l = -8 mA 0.25" 0.4 0.25 0.4 u
VOL Vee = 4.5 V, 10l = 16 mA
0.35 0.5
V en
(lOl = 24 rnA for - 1 versions) <t
II mA C
A or B ports Vee = 5.5 V, VI = 5.5 V 0.1
20
0.1
20
z
IIH
Control inputs
A or B ports§
Vee = 5.5 V, VI = 2.7 V
20 20
p.A <t
Control inputs
Vce = 5.5 V, VI = 0.4 V
-0.1 -0.1
mA
en
...J
IlL
A or B ports§ -0.1 -0.1
10' Vce = 5.5 V, Vo - 2.25 V -30 -112 -30 -112 mA

<t
Outputs high 6.5 6.5
'AlS1242 Outputs low 10 10
ICC Vce = 5.5 V rnA
Outputs high 8 8
'AlS1243 Outputs low 12 12

§For I/O ports, the parameters IIH and IlL include the off-state output current. '"
, The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
1283
TEXAS 2-705
INSTRUMENTS
'ALS 1242 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO
R1 = 500 n.
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
MIN TYP:I: MAX MIN TYP:I: MAX
tpLH 9 9
A or B B or A ns
tpHL 9 9
tpZH 17 17
GAB B ns
tPZL 19 19
tpHZ 7 7
GAB B ns
tpLZ 6 6
tpZH 17 17
GBA A ns
tPZL 19 19
tpHZ
GBA
-A 7 7
ns
tpLZ 6 6
'ALS 1242 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.5 V,
CL = 50 pF.
R1 = 500 fl.
~
FROM TO
(lNPUTI (OUTPUT)
TA = MIN to MAX
~ MIN TYP:I: MAX MIN TYP:I: MAX
r-
en tpLH
A or B B or A
11
11
11
11
ns
tpHL
~ tPZH 19 19
2 GAB B
21 21
ns
o tpZL
tpHZ
GAB B
9 9
ns
~ tpLZ
"
8 8
en tpZH
GBA A
19 19
ns
tpZL 21 21
~ tpHZ 9 9
::c tPLZ
GBA A
8 8
ns
(")
c tAli typical values are at Vee ~ 5 V, TA ~ 25°e.
=t NOTE 2: For load circuit and voltage waveforms, see page 1-12.
en
PRODUCT PREVIEW 12B3
2-7 06 !:~:I~:~e~~ni:~:sll~~~:~:~~ ~;.:.!'::~:~~~::~ TEXAS

change or discontinue this product without notice. INSTRUMENTS '
OCTAL BUFFER AND DRIVER WITH 3·STATE OUTPUTS
• Low-Power Version of 'ALS244A SN54ALS1244A ... J PACKAGE

SN74ALS1244A ... N PACKAGE
• 3-State Outputs Drive Bus Lines or Buffer Memory (TOP VIEW)
Address Registers
• P-N-P Inputs Reduce DC Loading 1<3
1A1
• Package Options Include Both Plastic and Ceramic 2Y4 1Y1
Chip Carriers in Addition to Plastic and Ceramic DIPs 1A2 2A4
• Dependable Texas Instruments Quality and Reliability 2Y3 1Y2
1A3 2A3
description 2Y2 1Y3
1A4 2A2
This octal buffer and line driver is designed specifically to
2Y1 1Y4
improve both the performance and density of three-state
GND 2A1
memory address drivers, clock drivers, and bus-oriented
receivers and transmitters. Taken together with the' ALS 1240
SN54ALS1244A ... FH PACKAGE
and' ALS 1241 this device provides the choice of selected com-
SN74ALS1244A ... FN PACKAGE
binations of inverting and noninverting outputs symmetrical G
(TOP VIEW)
(active-low input control) inputs, and complementary G and IT '<t..- U
inputs. >- <x: It!) Ult!)
N..-..->N
The-1 version of the SN74ALS 1244A is identical to the standard 3 2 1
version except that the recommended maximum IOL is increased 1A2 1Y1
to 24 milliamperes. There is no -1 version of the SN54ALS1244A. 2Y3 2A4
The SN54ALS1244A is characterized for operation over the full 1A3 1Y2
2Y2 2A3
military temperature range of - 55°C to 125°C. The
SN74ALS1244A is characterized for operation from DoC to 70°C. 1A4 1Y3
CJ)
functional block diagram (positive logic)
~
;:)
U
1A1
(2) (18) 1V1 a:
U
(4) (16)
1A2 logic symbol CJ)
«
1Y2
1A3
(6) (14)
1Y3
1G
c
z
1A4
(8) (12)
1Y4
1A1
1A2
1Y1
1Y2 «
1A3 1Y3 CJ)
-I
1A4 1Y4
«
2G
2A1 (111 >-_-+---"(9",,,,) 2Y1
2A1 2V1
2A2 2Y2
2A2 ....;,,(1;,;;;3.:.,.)----4 >-_-+--,"(7.;.,,) 2Y2
2A3 2Y3
2A4 2V4
2A3 (15) >-_-+---:.(5;;.:,.) 2Y3
2A4 (17) >-_ _--=-(3:.:.) 2Y4
Pin numbers showl' are for J and N packages

12B3
TEXAS 2-707
INSTRUMENTS
OCTAL BUFFER AND DRIVER WITH 3·STATE OUTPUTS
Supply voltage, Vee . .............................................................. " 7 V
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
Voltage applied to a disabled 3-state output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS1244A. . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 55°C to 125°e
SN74ALS1244A ................................ OOC to 70°C

IOL Low-level output current 8 16

mA
24t
The 24-mA limit applies for the SN7 4ALS 1244A-1 only.
..
l>
r-
en
PARAMETER
VIK
VOH
Vee
Vee
Vee
Vee
Vee
= 4.5
=
=
=
=
TEST CONDITIONS
V.
4.5 V to 5.5 V,
4.5 V.
4.5 V.
4.5 V.
II= - 18 rnA
IOH = -0.4 mA
IOH = -3 mA
IOH = -12 mA
IOH = -15 mA
MIN
2.4
SN54ALS1244A
Vee- 2
2
Typt
3.2
MAX
-1.5
SN74ALS1244A
MIN
Vee- 2
2.4
2
Typt
3.2
MAX
- 1.5
UNIT
l> Vee = 4.5 V. IOL = 8 mA

-
0.25 0.4 0.25 0.4
:2 VOL Vee = 4.5 V. IOL = 16 mA V
0.35 0.5
C (lOL = 24 mA for - 1 versions)
l> IOZH Vee = 5.5 V, Vo = 2.7 V 20 20 "A

en IOZL Vee = 5.5 V, VI = 0.4 V -20 -20 "A
(") II Vee = 5.5 V. VI = 7 V 0.1 0.1 mA
IIH Vee = 5.5 V. VI = 2.7 V 20 20 "A
ii
(")
IlL Vee = 5.5 V. VI = 0.4 V -0.1 -0.1 mA
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
c: t Outputs high 6 15 6 11
=i lee Vee = 5.5 V I Outputs low 10 20 10 17 mA
en I Outputs disabled 11 25 11 20
.
§The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS.
1283
2-708 TEXAS
INSTRUMENTS
OCTAL BUFFER AND DRIVER WITH 3-STATE OUTPUTS
switching characteristics (see Note 1) ,

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO R1 = 500 n.
PARAMETER UNIT
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 3 16 3 14
A Y ns
tpHL 3 16 3 14
tpZH 6 26 6 22
G y ns
tpZL 6 26 6 22
tpHZ 2 12 2 10
G Y ns
tpLZ 3 16 3 13
en
t:::
::>
u
a:
u
en
«
c
z
«
en
...J
«
1283
TEXAS 2-709
INSTRUMENTS
lEI
l>
r-
en
l>
:2
C
l>
en
S2
:ll
o
C
~
en
2-710
• 'Bidirectional Bus Transceivers in High-Density 20-Pin SN54ALS1245 .• , J PACKAGE

Packages SN74ALS1245 , , . N PACKAGE
(TOP VIEW)
• Lower-Power Version of 'ALS245
DIR Vee
• 'ALS 1245 is Identical to 'ALS 1645
A1 G
• Package Options Include Both Plastic and Ceramic Chip A2 81
Carriers in Addition to Plastic and Ceramic DIPs A3 82
A4 83
A5 84
A6 85
description
A7 86
This octal bus transceiver is designed for asynchronous two-way A8 87
communication between data buses. The device transmits data GND 88
from the A bus to the B bus or from the 8 bus to the A bus
depending upon the level at the direction control (DIR) input. The
SN54ALS1245 FH PACKAGE
enable input (G) can be used to disable the device so the buses
SN74ALS1245 FN PACKAGE
are effectively isolated,
The -1 version of the SN74ALS1245 is identical to the standard N ~!!: ~

<{ <{ 0 > I(!)
versions except that the recommended maximum IOL is
increased to 24 milliamperes. There is no -1 version of the 3 2 1
SN54ALS1245. 81
82
The SN54ALS 1245 is characterized for operation over the full
A5 83
military temperature range of - 55 °e to 125°e. The
84
SN74ALS1245 is characterized for operation from ooe to
A7 85
70 o e.
CONTROL
FUNCTION TABLE CXlOCXlr--CO
<{ZCXlaJaJ en
INPUTS OPERATION
(!)
!::
::>
G DIR
logic symbol u
L
L
L
H
B data to A bus
A data to B bus G (19)
a:
H X Isolation
DIR
(1) u
en
A1
(2) (1 B)
B1 «
logic diagram (positive logic) (3) (17)
c
A2 B2 2
'G------,
A3 (4) (16) B3
«
en
-I
DIR -+-----'
A4
(5) (15) B4
«
(6) (14) B5
A5
A1 B1
(7) (13) B6
AS
(B) (12) B7
A7
TO SEVEN OTHER TRANSCIEVERS
AB (9) (11) B8

1283
TEXAS 2-711
INSTRUMENTS
absolute maximum ratings over operating free-air temperature range (unless otherr-rise noted)
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports ..........' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS1245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55 De to 125 De
SN74ALS1245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODe~70De
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65 De to 150 °e

8 16
24t
tThe extended limit applies only If Vee IS maintained between 4.75 V and 5.25 V.
..
The 24-mA limit applies for the SN74ALS1245-1 only .
Typt Typt
l> MIN MAX MIN MAX
r- VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V
en Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 Vee- 2
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2
l> VOH V
z Vee
VCC
= 4.5 V,
= 4.5 V,
10H = -12 mA
= -15 mA
2
2
C 10H
Vee = 4.5 V, 10L = 8 mA 0.25 0.4 0.25 0.4
l> VOL Vee = 4.5 V, 10L = 16 mA V
en (lOL = 24 mA for - 1 version)
0.35 0.5
~ II
Control inputs
A, 8 ports§
Vee
Vee
= 5.5 V,
= 5.5 V,
VI
VI
=
=
7 V
5.5 V
0.1
0.1
0.1
0.1
mA
:D
o IIH
Control inputs
Vce = 5.5 V, VI = 2.7 V
20 20
p.A
c A, 8 ports§ 20 20
=i
(J)
IlL
Control inputs
A, 8 ports§
Vee = 5.5 V, VI = 0.4 V
-0.1
-0.1
-0.1
-0.1
mA
10' Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA

lOutput high 20 33 20 32
Ice Vee = 5.5 V I Output low 23 39 23 37 mA
I Output disabled 25 41 25 39

'The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS.
1283
2-712 TEXAS
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
Rl = 500 Q.
FROM TO R2 = 500 Q.
PARAMETER UNIT
MIN MAX MIN MAX
tpLH 4 15 4 13
A or B B or A ns
tpHL 4 15 4 13
tpZH 10 27 10 25
IT A or B ns
tpZL 13 32 13 29
tpHZ 4 20 4 18
"IT A or B ns
tpLZ 5 23 5 21
(J)
!::
::::>
u
a:
u
(J)
«
c
:2
«
C/)
..J
«
1283
TEXAS 2-713
INSTRUMENTS
IB
l>
r-
en
l>
2
C
l>
en
(")
$
(")
c:
=t
en
2-714
TYPES SN54ALS1620 THRU SN54ALS1623
SN74ALS1620 THRU SN74ALS1623
• Bus Transceivers in High-Density 20-Pin DIPs and the SN54ALS' •.• J PACKAGE
New Plastic and Ceramic Chip Carriers Packages SN74ALS' ••. N PACKAGE
(TOPVIEWI
• Local Bus Latch Capability
GAB VCC
A1 GBA
• Dependable Texas Instruments Quality and Reliability A2 B1
A3 B2
• Choice of 3-State or Open-Collector Outputs
A4 83
A5 84
DEVICE OUTPUT LOGIC
A6 85
'ALS1620 3-State Inverting
A7 86
A8 B7
GND 88
'ALS1623 3-State True
description
SN54ALS' ••• FH PACKAGE
These octal bus transceivers are designed for asynchronous two-
SN74ALS' •.• FN PACKAGE
way communication between data buses. The control function
(TOPVIEWI
implementation allows for maximum flexibility in timing.
N
CD u
.... «UCD
«
These devices allow data transmission from A bus to the B bus or
« « t!) > It!)
from the B bus to the A bus depending upon the logic levels at the
enable inputs (GBA and GAB).
A3 B1
The enable inputs can be used to disable the device so that the
A4 B2
buses are effectively isolated.
A5 B3
The dual-enable configuration gives the ' ALS 1620 thru A6 B4
, ALS1623 the capability to store data by simultaneous enabling A7 B5
of GBA and GAB. Each output reinforces its input in this en
transceiver configuration. Thus, when both control inputs are t::
enabled and all other data sources to the two sets of bus lines are :J
at high impedance, both sets of bus lines (16 in all) will remain at U
their last states. The 8-bit codes app"earing on the two sets of ex:
buses will be identical for the ' ALS 1621 and ' ALS 1623 or U
complementary for the' ALS 1620 and' ALS 1622.
en
The -1 versions of the SN74ALS' parts are identical to the -d:
increased to 24 mAo There are no -1 versions of the SN54ALS'
o
parts.
Z
-d:
The SN54ALS1620 thru SN54ALS1623 are characterized for
en
...J
125°C. The SN74ALS1620 thru SN74ALS1623 are -d:
characterized for operation from 0 °C. to 70°C.
FUNCTION TABLE

GBA GAB 'ALS1620, 'ALS1622 'ALS1621, 'ALS1623
L H

ThIs document contains information on a product under
development. Teus Instruments reserv.s the right to TEXAS 2-715
logic symbols
'ALS1620 'ALS1621 'ALS1622 'ALS1623
'ALS1620 'ALS1621 'ALS1622 'ALS1623
lllA----c:t
GAl o.u
~Al 81 AI II .,
l>
r-
CA A2 12 A2 12 12
l>
2
C
l> TO OTHER SIX TO OTHER SIX TO OTHER SIX TO OTHER SIX
CA TRANSCEIVERS TRANSCEIVERS TRANSCEIVERS TRANSCEIVERS
C') Pin numbers shown are for J and N packages.

$
C')
c:
=t
C/)
1283
2-716 TEXAS
INSTRUMENTS
TYPES SN54ALS1620 THRU SN54ALS162l
Supply voltage. VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
lID ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS1620. SN54ALS1623 . . . . . . . . . . . . . . . . . . - 55 OCto 125°C
SN74ALS1620.SN74ALS1623 . . . . . . . . . . . . . . . . . . . . . 0°Ct070°C
Storage temperature range .... ',' . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .'. - 65°C to 150°C

6 16
24 t
MIN TYP:I= MAX MIN TYP:I= MAX
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V en
Vee = 4.5 V to 5.5 V, IOH = -0.4 mA Vee- 2 vee- 2 C
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2 :::l
VOH
Vee = 4.5 V, IOH = -12 mA 2
V U
Vee = 4.5 V, 10H = -15 mA 2
a:
Vee = 4.5 V, 10L = 6 mA 0.25 0.4 0.25 0.4 (.)
VOL Vee = 4.5 V, 10L = 16 mA
0.35 0.5
V
en
Control inputs
(lOL = 24 mA for-1 versions)
Vee = 5.5 V, VI = 7 V 0.1 0.1
«
II
mA c
z
IIH
Control inputs
A or B ports§
Vee = 5.5 V, VI = 2.7 V
20
20
20
20
p.A «
IlL
Control inputs
= =
-0.1 -0.1 en
Vee 5.5 V, VI 0.4 V mA ..J
10'
A or B ports§
Vee - 5.5 V, Vo - 2.25 V -30
-0.1
-112 -30
-0.1
-112 mA «
Outputs high 14 14
Outputs disabled 21 21 -
ICC Vee = 5.5 V mA
Outputs high 11 11
tAli typical values are at-Vee ~ 5 V, TA ~ 25°e.

,The output conditions have been chosen to produce a current that closely approximates one h'alf of the true short-circuit output current, lOS.
1283
TEXAS 2-717
INSTRUMENTS
POST OFFICE BOX 225012 • DALLAS. TEXAS '75265

Vec = 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
tPLH 9 9
A B ns
tpHL 6 6
tpLH 9 9
B A ns
tPHL 6 6
tPZH 14 14
GBA A ns
tPZL 17 17
tpHZ 7 7
GBA A ns
tpLZ 11 11
tPZH 14 14
GAB B ns
tPZL 17 17
tpHZ 7 7
GAB B ns
tpLZ 11 11
..
»
r-
tn
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
SN54ALS1623
Vee
CL
R1
R2
TA
= 4.5 V to 5.5
= 50 pF.
= 500 n.
= 500 n.
= MIN to MAX
V.
SN74ALS1623
UNIT
»
2 tPLH
MIN Typt MAX
8
MIN Typt MAX
8
o tpHL
A 8
8 8
ns
»
en
tPLH
tpHL
B A
8
8
8
8
ns
tpZH 18 18
Q GBA A ns
tPZL 21 21
::a tpHZ 12 12
o tpLZ
GBA A
13 13
ns
c tpZH 18 18
=t
en
tPZL
GAB B
21 21
ns
tpHZ 12 12
GAB B ns
tpLZ 13 13
tAli typical values are at VCC = 5 V. TA = 25 DC.

1283
2-718 TEXAS
INSTRUMENTS
Supply voltage. Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage: All inputs and I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1621. SN54ALS 1622 . . . . . . . . . . . . . . . . . . - 55 DC to 125 De
SN74ALS1621.SN74ALS1622 . . . . . . . . . . . . . . . . . . . . . OOet070 De
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 DC to 150 De

VOH High-level output voltage 5.5 5.5 mV
8 16
24 t
electrical characterJstics over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS SN54AlS1622
MIN Typt MAX
SN74AlS1622
MIN Typt MAX
UNIT
en
Vee = 4.5 V. II = -18 mA -1.5 -1.5 V
!::
VIK
::>
10H Vee = 4.5 V. VOH = 5.5 V 0.1 0.1 mA
u
Vee = 4.5 V. IOl = 8 mA 0.25 0.4 0.25 0.4 a:
VOL Vee = 4.5 V.
(\Ol = 24 mA
IOl
for - 1 versions)
= 16 mA
0.35 0.5
V
u
Control inputs Vec = 5.5 V. VI = 7 V 0.1 0.1 en
II
A or B ports VCC = 5.5 V. VI = 5.5 V 0.1 0.1
mA
«
IIH
Control inputs
Vec = 5.5 V. VI = 2.7 V
20 20
p.A c
A or B ports§ 20 20
z
III
Control inputs
VCC = 5.5 V. VI = 0.4 V
-0.1 -0.1
mA «
A or B ports§
Outputs high 11
-0.1
11
-0.1
en
-I
ICC
'AlS1621
VCC = 5.5 V
Outputs low
Outputs high
16
13
16
13
mA
«
'AlS1622
Outputs low 18 18

§For 1/0 ports, the parameters IIH and IlL include the off· state output current.
1283
TEXAS 2-719
INSTRUMENTS
Vee = 4.5 V to 5.5 V.

eL = 50 pF.
FROM TO RL = 680 n.
PARAMETER UNIT
tPLH 22 22
A B ns
tpHL 14 14
tpLH 22 22
B A ns
tPHL 14 14
tpLH 33 33
GSA A ns
tPHL 24 24
tpLH 33 33
GAB B ns
tpHL 24 24
Vee = 4.5 V to 5.5 V.

CL = 50 pF.
FROM TO RL = 680 n.
PARAMETER UNIT
III MIN
SN54ALS 1622
Typt MAX MIN
SN74ALS1622
Typt MAX
»r- tpLH
A B
25 25
ns
en tpHL
tpLH
13
25
13
25
»
2
tpHL
tpLH
B A
13
31
13
31
ns
GSA A ns
C tpHL 28 28
»
en
tpLH
tpHL
GAB B
31
28
31
28
ns
(") tAli typical values are at Vee = 5 V. TA = 25°e.

:D
(")
c
=i
en
1283
2-720 TEXAs
INsrRUMENlS
• Bidirectional Bus Transceivers in High-Density 20-Pin SN54ALS1638,SN54ALS1639 . J PACKAGE

Packages SN74ALS1638,SN74ALS1639 . N PACKAGE
(TOP VIEW)
g Low-Powor Version of ' ALS638 and' ALS639
DIR VCC
A1 G
• A bus Outputs are Open-Collector; B Bus Outputs are A2 81
3-State A3 82
A4 83
A5 84
A6 85
A8 87
description GND 88

way communication between open-collector and 3-State buses.
The devices transmit data from the A bus (open-collector) to the
8 bus (3-state) or from the 8 bus to the A bus depending upon
the level at the direction control (DIR) input. The enable input (G)
can be used to enable the device so the buses are effectively
isolated. SN54ALS1638,SN54ALS1639 . FH PACKAGE
SN74ALS1638,SN74ALS1639 . FN PACKAGE
DEVICE A OUTPUT B OUTPUT LOGIC
(TOP VIEW)
'ALS 1638 Open-Collector 3-State Inverting
'ALS 1639 Open-Collector 3-State True N .- ~ ~
<{ <{ 0 >I(!)
A3 4 81
increased to 24 milliamperes. There are no -1 versions of the
A4 5 82 CJ)
SN54ALS' parts.

A5
A6
6
7
83 t::
84 ::J
operation over the full military temperature range of - 55 DC to A7 8 85 (.)
125 DC. The SN74ALS1638 and SN74ALS1639 are a:
characterized for operation from 0 DC to 70 DC. (.)
ooOOOI'CO
<{z CD CD CD
(!) CJ)
<t
o
Z
FUNCTION TABLE
<t
CJ)
CONTROL
OPERATION -'
INPUTS
'ALS1638 'ALS1639 <t
G DIR
L H A data to B bus A data to B bus
H X Isolation Isolation
ADVANCE INFORMATION Copyright © 1982 by Texas Instruments Incorporated

1283
ThIs document contalns Informatfan on a new product.
Speclf1cationa are subject to change whhDut notice. ' TEXAS 2-721
INSTRUMENTS
POST OFFICE BOX 225012 a DALLAS. TEXAS 75265
logic symbols functional block diagrams (positive logic)
'AlS1638 'AlS1638
At Bt
A2
B3 Bt
B4
AS BS
B2
A6 B6
A7 B7
lEI A8 B8
l>
r- 'AlS1639 'AlS1639
en \.
,0
l> orR
:2
C At Bt
l> DIR
en A2 B2
Q A3 B3 At Bt
::Jl A4 B4
(')
C
:::; AS BS
en A6 B6
A2 B2
A7 B7
A8 B8
1283
2-722 TEXAS
INSTRUMENTS
POST OFFICE 80X 225012 • DALLAS. TEXAS 75265
A bus I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
B bus I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range: SN54ALS 1638, SN54ALS1639 . . . . . . . . . . . . . . . . - 55°C to 125 °e
SN74ALS1638,SN74ALS1639 . . . . . . . . . . . . . . . . . . . . OOeto70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50 °e

UNIT
VOH High-level voltage A ports 5.5 5.5 V
10H High-level output current B ports -12 -15 rnA
8 16
10L Low-level output current A or B ports rnA
24 t
The 24-mA limit applies for the SN7 4ALS 1638-1 and SN7 4ALS 1639-1 only.
en
MIN TVP:t: MAX MIN TVP:t: MAX I-
Vee = 4.5 V. = -18 rnA -1.5 -1.5 V
VIK
10H A ports Vec = 4.5 V.
II
Va = 5.5 V 0.1 0.1 rnA
::>
=
U
Vcc 4.5 V to 5.5 V. IOH = -0.4 rnA vee- 2 Vee- 2 a:
=
VOH B ports
Vcc
VCC =
4.5 V.
4.5 V.
10H = -3 rnA
10H = -12mA
2.4
2
3.2 2.4 3.2
V u
VCC = 4.5 V. 10H = -15 rnA 2 en
Vee = 4.5 V. 10L = 8 rnA 0.25 0.4 0.25 0.4 <t
VOL A or B ports VCC
(IOL
= 4.5 V.
=
10L = 16 rnA
24 rnA for - 1 versions)
0.35 0.5
V
o
2
II
Control inputs
A or B ports
VCC
VCC
=
=
5.5 V.
5.5 V.
VI =
VI 5.5 V
7 V 0.1
0.1
0.1
0.1
rnA <t
Control inputs 20 20 en
IIH VCC = 5.5 V. VI = 2.7 V p.A ..J
A or B ports§
Control inputs
20
-0.1
20
-0.1
<t
IlL VCC = 5.5 V. VI = 0.4 V rnA
A or B ports§ -0.1 -0.1
10' B ports VCC = 5.5 V, Va = 2.25 V -30 -112 -30 -112 rnA
I Outputs high 21 21
ICC VCC = 5.5 V I Outputs low 23 23 rnA
;AII typical values are at Vee = 5 V. TA = 25°e.

§For I/O ports. the parameters IIH and IlL include the off· state output current.
,The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current. lOS'
1283'
TEXAS 2-723
INSTRUMENTS

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
RL = 500 Q (A outputs).
FROM TO
PARAMETER R1 = R2 = 500 Q (B outputs) UNIT
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54ALS1638 SN74ALS 1638
tpLH 6 6
A 8 ns
tPHl 21 21
tpLH 6 6
8 A ns
tpHL 8 8
tf'LH 23 23
G.OIR A ns
tpHL 17 17
tpZH 12 12
G 8 ns
tpZL 15 15
tpHZ 6 6
G B ns
tpLZ 7 7
•ALS 1639 switching characteistics (see Note 1)

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
16 PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
RL = 500 Q (A outputs).
R1 = R2 = 500 Q (B outputs).
TA = MIN to MAX
UNIT
»
r-
SN54ALS 1639
MIN Typt MAX
SN74ALS 1639
MIN Typt MAX
tJ)
tpLH 7 7
»
2!
tpHL
tpLH
A 8
21
7
21
7
ns
c tpHL
8 A
9 9
ns
»
tJ)
tpLH
tpHL
G. orR A
23
19
23
19
ns
tpZH 14 14
Q tpZL
G B
17 17
ns
::n tpHZ
G B
7 7
ns
·0 tpLZ 9 9
c tAli typical values at VCC = 5 V. TA = 25°C.·
::::; NOTE 1: For load circuit and voltage waveforms. see page 1-12.
(J)
1283
2-724 TEXAS
INSTRUMENTS
TYPES SN54ALS1640A, SN54ALS1645A, SN54ALS1641 THRU SN54ALS1644
SN74ALS1640A, SN74ALS1645A, SN74ALS1641 THRU SN74ALS1644
• Bidirectional Bus Transceivers in High-Density 20-Pin SN54ALS' ... J PACKAGE

Packages SN74ALS' ... N PACKAGE
ITOPVIEWI
• Lower-Power Versions of 'ALS640 Series
DIR Vee
• Choice of True or Inverting Logic A1 G
• Choice of 3-State or Open-Collector Outputs A2 81
A3 82
A4 83
A5 84
A7 86
DEVICE OUTPUT LOGIC A8 87
'ALS1640A 3-State Inverting GND 88
SN54' ... FH PACKAGE
'ALS1643 3-5tate True and Inverting
SN74' ... FN PACKAGE
'ALS1644 Open-Collector True and Inverting
ITOPVIEWI
'AL51645A 3-State True
N .- Q;; ~
description « « 0 > It!)
way communication between data buses. The devices transmit A3 81
data from the A bus to the 8 bus or from the 8 bus to the A bus A4 82
depending upon the level at the direction control (DIR) input. The A5 83
enable input ((3) can be used to disable the device so the buses A6 84
are effectively isolated. A7 85
The -1 versions of the SN74ALS' parts are identical to the standard en

versions except that the recommended maximum IOL is increased
CXlOCXlI'CD
«zcococo
t!)
!::
to 24 milliamperes. There are no -1 versions of the :::>
SN54ALS' parts. u
The SN54ALS' family is characterized for operation over the full
a:
military temperature range of - 55 °e to 125°C. The SN74ALS' u
family is characterized for operation from OOC to 70 oe. en
<t
FUNCTION TABLE
C
Z
CONTROL OPERATION <t
INPUTS 'ALS1640A 'ALS1641
'ALS1645A
'ALS1643
'ALS1644
en
....I
G DIR 'ALS1642
L L B data to A bus B data to A bus B data to A bus <t
L H A data to B bus A data to B bus A data to B bus
H X Isolation Isolation Isolation
TEXAS 2-725
INSTRUMENlS
TYPES SN54ALS1640A, SN54ALS1645A, SN54ALS1641 THRU SN54ALS1644
SN74ALS1640A, SN74ALS1645A, SN74ALS1641 THRU SN74ALS1644
logic symbols
'ALS1640A 'ALS1641
81
A2 A2 A2
A3 83 A3 83 A3 83
84 84 84
85 85 A5 85
A6 86 86 A6 86
87 A7 87 87
A8 88 AS
'ALS1644 'ALS1645A
Al 81 Al
A2 A2 82 82
A3 83 A3 83 A3 83
84 84
AS 85 85 A5
lEI
A6 86 A6 86 86
87 87
»
r-
A8 88 A8 B8
en logic diagrams (positive logic)
»
2
'ALS1640A 'ALS1641 'ALS1642
C
»
en
CIR CIR
(") A1 B1 Bl Al Bl
:lJ
(")
C TO SEVEN OTHER TRANSCEIVERS
~
TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS
CJ) 'ALS1643 'ALS1644 'ALS1645A

G
CIR CIR CIR
Al Bl Al Bl Al Bl
TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS

1283
2-726 TEXAS
INSTRUMENTS
TYPES SN54ALS1640A, SN54ALS1643, SN54ALS1645A
SN74ALS1640A, SN74ALS1643, SN74ALS1645A
Supply voltage, Vee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7 V
I/O ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54ALS1640A, SN54ALS1643, SN54ALS1645A ... -55°C to 125°e
SN74ALS1640A, SN74ALS1643, SN74ALS1645A ...... ooe to 70 0 e
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 1 50 °e
UNIT
VIL Low-level input voltage - 0.8 0.8 V
8 16
24t
tThe extended limits apply only if Vee is maintained bet~een 4.75 V and 5.25 V.
The 24-mA limit applies for the SN74ALS1640A-1, SN74ALS1643-1, and SN74ALS1645A-1 only.
MIN TVP~ MAX MIN TVP~ MAX CJ)
VIK Vee = 4.5 V, II = -18 mA -1.5 -1.5 V !:::
Vee = 4.5 V to 5.5 V, IOH - -0.4 mA Vee- 2 Vee- 2 :::>
Vee = 4.5 V, 10H = -3 mA 2.4 3.2 2.4 3.2 u
VOH
Vee = 4.5 V, 10H = -12 mA 2
V
g;
Vee = 4.5 V,
Vee = 4.5 V,
10H = -15 mA
10L = 8 mA 0.25 0.4
2
0.25 0.4
u
CJ)
VOL Vee = 4.5 V, 10L = 16mA V
(lOL = 24 mA for - 1 versions)
0.35 0.5 ~
Control inputs VCC = 5.5 V, VI = 7 V 0.1 0.1 C
II
A or B ports VCC = 5.5 V, VI = 5.5 V 0.1 0.1
mA
z
IIH
Control inputs
A or B ports§
VCC = 5.5 V, VI = 2.7 V
20 20
20
p.A
«
20 CJ)
Control inputs -0.1 -0.1 ...J
IlL VCC = 5.5 V, VI = 0.4 V mA
A or B ports§- -0.1 -0.1 ~
10' Vce = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 mA
'ALS1640A .18 35 18 32
ICC 'ALS1643 Vce = 5.5 V 22 22 mA
'ALS1645A 25 40 25 36

'The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, lOS'

This page contains Information on a new product.
Specifications ar. subject to change without notlca. TEXAS 2-727
INSTRUMENTS
TYPES SN54ALS1640A, SN54ALS1643, SN54ALS1645A
SN74ALS1640A, SN74ALS1643, SN74ALS1645A
•ALS 1640A switching characteristics (see Note 1)
Vcc - 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
PARAMETER
(INPUT) (OUTPUT)
R2 = 500 n. UNIT
TA = MIN to MAX
MIN MAX' MIN MAX
tpLH 5 17 5 15
A or B B or A ns
tpHL 2 13 2 10
tpZH 5 23 5 20
G A or B
5 25 5 22
ns
tpZL
tpHZ 2 12 2 10
G A or B
16
ns
tpLZ 5 5 13
I ALS 1643 switching characteristics (see Note 1)

Vcc = 4.5 V to 5.6 V.
CL = 60 pF.
R1 = 500 Q.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
tPLH 7 7
A B ns
tPHL 7 7
IIIfI tpLH
tpHL
B A
8
8
8
8
ns
l> tPZH
G A
18 18
ns
r- tpZL 21 21
CJ) tPHZ 12 12
G A ns
13 13
l> tPLZ
tpZH 18 18
2 G 8 ns
tpZL 21 21
C
12 12
»
en
tpHZ
tpLZ
G B
13 13
ns
Q .ALS1645A switching characteristics (see Note 1)

::D Vcc = 4.5 V to 5.5 V.
n CL = 50 pF.
c: FROM TO
R1 = 500 n.
~ PARAMETER R2 = 500 n. UNIT
en (INPUT) (OUTPUT)
TA = MIN to MAX
MIN MAX MIN MAX
tpLH 2 15 2 13
A or B B or A ns
tpHL 2 15 2 13
tpZH 8 28 8 25
G A or B ns
tpZL 8 28 8 25
tpHZ 2 14 2 12
G A or B ns
tpLZ 3 22 3 18

ADVANCE INFORMATION 1283
2 -7 2 8
This page contains Informallon 'on a new product.
Specifications are subject to change without nollce. TEXAS
INSfRUMENTS
POST OFFICE BOX 225012 e DALLAS. TEXAS 75265 .
Input voltage: All inputs and 1/0 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating free-air temperature range: SN54ALS 1641, SN54ALS 1642, SN54ALS 1644 ..... - 55 DC to 125 De
SN74ALS1641,SN74ALS1642,SN74ALS1644 ......... Ooew70oe
Storage temperature range . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .. - 65 De to 150 De

SN 54ALS 1642 SN74ALS1642
UNIT
8 16
24t
tThe extended limits apply only' if Vee is maintained between 4.75 V and 5.25 V.
The 24-mA limit applies for the SN74ALS1641-1, SN74ALS1642-1, and SN74ALS1644-1 only.
en
SN54ALS1641
SN54ALS1642
SN74ALS1641
SN74ALS1642
t:
UNIT ::::l
U
VCC = 4.5 V, II = -18 rnA
MIN TYP; MAX
-1.5
MIN TYP; MAX
-1.5 V
a:
VIK
10H VCC = 4.5 V, VOH = 5.5 V 0.1 0.1 mA U
VCC = 4.5 V, 10L = 8 mA 0.25 0.4 0.25 0.4 en
VOL Vce = 4.5 V, 10L - 16 rnA
0.35 0.5
V <t
C
Control inputs Vce = 5.5 V, VI = 7 V 0.1 0.1
II mA 2
VCC = 5.5 V,
A or B ports
Control inputs
VI = 5.5V 0.1
20
0.1
20
<t
IIH A or B ports§
VCC = 5.5 V, VI = 2.7V
20 20
",A en
..J
IlL A or B ports§
VCC = 5.5V, VI = 0.4 V
-0.1 -0.1
mA <t
'ALS1641 23 23
ICC 'ALS1642 VCC = 5.5 V 20 20 mA
'ALS1644 22 22


development. Texas Instruments reserves the right to
change or discontinue this product without notlc ••
TEXAS 2-729
INSTRUMENTS
Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
FROM TO RL = 50011,
PARAMETER UNIT
(INPUT} (OUTPUT} TA = MIN to MAX
tPLH 22 22
A or B B or A ns
tpHL 14 14
tPLH 26 26
G or DIR A or B ns
tpHL 26 26

Vcc = 4.5 V to 5.5 V,
CL = 50 pF,
PARAMETER
FROM TO RL = 50011.
UNIT
(INPUT} (OUTPUT} TA = MIN to MAX
tpLH 25 25
A or B B or A ns
tpHL 13 13
..
tpLH 29 29
G or DIR A or B ns
tpHL 29 29

Vcc = 4.5 V to 5.5 V.
»
r- PARAMETER
FROM TO
CL
RL
= 50 pF.
= 50011,
UNIT
en (INPUT} (OUTPUT} TA = MIN to MAX
»
2
SN54ALS1644
MIN Typt MAX MIN
SN74ALS1644
Typt MAX
o tpLH
tPHL
A B
27
19
27
19
ns
»
en
tPLH
tPHL
B A
24
17
24
17
ns
~
tpLH 30 30
G or DIR A ns
tPHL 27 27
::xJ
o tpLH
G or DIR B
24 24
ns
c tpHL 30 30
=i t All typical values are at Vee = 5 V. T A = 25°e.

fA NOTE 1: For load circuit and voltage waveforms, see page 1-12.

Thl. page contain. information on a product und.r
2-730 d.velopment. T.x.. Inotrumente ....rv•• the right to
chong. or dl.contlnue thl. product without notlc•.
TEXAS
INSTRUMENTS
OCTAL BUS TRANSCEIVERS/MOS DRIVER
DECEMBER 1983
• Bidirectional Octal Bus Transceivers For SN54AS' ... J PACKAGE

Driving MaS Devices SN74AS' ... N PACKAGE
(TOP VIEW)
• I/O Ports Have 25 Ohm Series Resistors So
No External Resistors Are Required GAB Vee
A1 GBA
• Local Bus-Latch Capability
A2 B1
• Choice of True or Inverting Logic A3 B2
A4 B3
A5 B4
Reliability
A6 B5
A7 B6
description
A8 B7
These octal bus transceivers are designed to drive GND B8
the capacitive input characteristics of MOS devices
and allow asynchronous two-way communication
SN54AS' ... FH PACKAGE
between data buses. The control function implemen-
SN74AS' ... FN PACKAGE
tation allows for maximum flexibility in timing. (TOP VIEW)
These devices allow data transmission from A bus to co u «
N .... «UCO
the B bus or from the B bus to the A bus depending «« > 1<.:)
<.:)
upon the logic levels at the enable inputs (GBA and
GAB).
A3 B1
The enable inputs can be used to disable the device A4 B2
so that the buses are effectively isolated. A5 B3
A6 B4
The dual-enable configuration gives the' AS2620 or
A7 B5
, AS2623 the capability to store data by simulta-
neous enabling of GBA and GAB. Each output rein-
co
en
forces its input in this transceiver configuration.
Thus, when both control inputs are enabled and all
«
0
z
<.:)
COI'CO
COCO CO t:
:::>
other data sources to the two sets of bus lines are at
high impedance, both sets of bus lines (1 6 in all) will
u
remain at their last states. The 8-bit codes appearing
a:
on the two sets of buses will be identical for the u
'AS2623 or complementary for the 'AS2620. en
The SN54AS2620 and SN54AS2623 are charac- «
terized for operation over the full military temperature o
range of - 55°C to 125°C. The SN74AS2620 and :2
SN74AS2623 are characterized for operation from
ooe to 70°C.
«
en
-oJ
FUNCTION TABLE «
GBA GAB 'AS2620 'AS2623
L H
TEXAS
INSTRUMENTS
TVPESSN54AS2620,SN54AS2623,SN74AS2620,SN74AS2623
logic symbols
'AS2620 'AS2623
'AS2620 'AS2623
-
GAB
Al Bl Al Bl
l>
r-
tJ)
l> A2 B2 A2 B2
2:
o
l>
tJ) TO OTHER SIX TO OTHER SIX
TRANSCEIVERS TRANSCEIVERS
o
:xJ
o
c
=ttJ)
1283
2-732 TEXAS
INSTRUMENlS
TYPESSN54AS262D,SN54AS2623,SN74AS262D,SN74AS2623
Input voltage: All inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . '...................... 5.5 V
Operating free-air temperature range: SN54AS2620, SN54AS2623 .................... - 55°C to 125°C
SN74AS2620,SN74AS2623 . . . . . . . . . . . . . . . . . . . . . . . . OOCto70oC
reco,!,mended operating conditions

SN54AS2620 SN74AS2620
SN54AS2620 SN74AS2620
VIK Vee = 4.5 V, II = -18 mA -1.2 -1.2 V
VOH Vee = 4.5 V to 5.5 V, IOH = -2mA Vee- 2 Vee- 2 V
Vee = 4.5 V, IOl = 1 mA 0.15 0.4 0.15 0.4
VOL V
Vee = 4.5 V, IOl = 12 mA 0.35 0.7 0.35 0.7
II rnA
IIH Vee = 5.5 V, VI = 2.7V 50
/J A
A or B ports* 50
III Vee = 5.5 V, VI= 0.4 V -0.5 -0.5
mA
A or B ports*
lo§ Vee = 5.5 V, Vo = 2.25 V -30 -112 -30 -112 rnA
IOH Vee = 4.5 V, Vo = 2 V -35 -35 mA
IOl Vee = 4.5 V, Vo = 2 V 35 35 mA
'AS2620 Vee = 5.5 V Outputs low 74 121 74 121
ICC mA
'AS2623 Vee = 5.5 V Outputs low 116 189 116 189
*For I/O ports. the parameters IIH and IlL include the off-state output current.
1283
TEXAS 2-733
INSTRUMENTS
TYPESSN54AS2620,SN54AS2623,SN74AS2620,SN74AS2623

Vcc - 4.5 V to 5.5 V.
CL = 50 pF.
R1 = 500 n.
FROM TO
(INPUT) (OUTPUT)
TA = MIN to MAX
SN54AS2620 SN74AS2620
MIN MAX MIN MAX
tpLH 1 9.5 1 8
A B ns
tPHL 1 7.5 1 6.5
tpLH 1 9.5 1 8
B A ns
tpHL 1 7.5 1 6.5
tpZH 1 11 1 10
GSA A ns
tpZL 1 12 1 11
tpHZ 1 7.5 1 6
GSA A ns
tpLZ 1 15 1 12
tpZH 1 9 1 8
GAB B ns
tpZL 1 9 1 8
tPHZ 1 12 1 11
GAB B ns
tPLZ 1 12 1 11

Vcc = 4.5 V to 5.5 V.
CL = 50 pF.
III PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
R1
R2
= 500 n.
= 500 n. UNIT
»
r-
TA
SN54AS2623
= MIN to MAX
SN74AS2623
o MIN MAX MIN MAX
»
:2
tpLH
tpHL
A B
1
1
9.5
8.5
1
1
8.5
7.5
ns
1 10 1
C tPLH
S A
9
ns
»
o
tPHL
tpZH
GBA A
1
1
9
12.5
1
1
7.5
11
ns
tpZL 1 12 1 11
o
-::u
o
tpHZ
tPLZ
tpZH
GBA A
1
1
1
8.5
13
13
1
1
1
7.5
12
12
ns
GAB B ns
c tpZL 1 13.5 1 12
~ tPHZ
GAB B
1 7.5 1 7
ns
o tPLZ 1 14.5 1 12.5
1283
2-734 TEXAS
INSTRUMENTS
SN74AS2640, SN74AS2645
OCTAL BUS TRANSCEIVER/MOS DRIVER
DeCEMBER 1983
• Bidirectional Octal Bus Transceivers For SN54AS' ••• J PACKAGE

Driving MOS Devices SN74AS' ••• N PACKAGE
ITOPVIEWI
Q I/O Ports Hnvo 25 Ohm Series Resistors So
No External Resistors Are Required DIR Vcc
A1 G
A2 81
• Dependable Texas Instruments Quality and A3 82
Reliability A4 83
A5 84
description A6 85
A7 86
These octal bus transceivers are designed to drive
A8 87
the capacitive input characteristics of MOS devices
GND 88
and allow asynchronous two-way communication
between data buses. The control function implemen-
tation allows for maximum flexibility in timing. SN54AS' ••• FH PACKAGE
SN74AS' •.• FN PACKAGE
The devices transmit data from the A bus to the 8
ITOPVIEWI
bus or from the 8 bus to the A bus depending upon
the level at the direction control (DIR) input. The N .- ~ ~
enable input {G) can be used to disable the device so « « 0 > Ie.!)
the buses are effectively isolated.
The SN54AS' family is characterized for operation 81

over the full military temperature range of - 55°C to A4 82
125°C. The SN74AS' family is characterized for A5 83
operation from ooC to 70°C. A6 84
A7 85
coocor--co
en
«z co co co
e.!)
!:::
:::>
(.)
FUNCTION TABLE a::
CONTROL OPERATION (.)
INPUTS
G DIR
'AS2640 'AS2645 en
~
L H A data to B bus A data to B bus c
H X Isolation Isolation z
~
en
...J
~

This document contains Information on a product under
development. Tuaslnstruments re.erYe. the right to TEXAS 2-735
SN74AS2640, SN74AS2645
OCTAL BUS TRANSCEIVER/MOS DRIVER
logic symbols
'AS2640 'AS2645
A1 B1
B1
A2 B2
B2
A3 B3
B3
B4
B4
A5 B5
B5
A6 B6
B6
A7 B7
B7
A8 B8
B8
'AS2640 'AS2645
l;------..,
DIR --+----~
A1 B1 B1
TO SEVEN OTHER TRANSCEIVERS TO SEVEN OTHER TRANSCEIVERS
1283
2-736
TEXAS .
INSTRUMENTS
SN74AS2640. SN74AS2645
Supply voltage; Vee ................................................................. , 7 V
I/O ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 5.5 V
Operating free-air temperature range: SN54AS2640, SN54AS2645 .... . . . . . . . . . . . . . .. - 55°C to 125 °e
SN74AS2640, SN74AS2645 ....................... ooe to 70 0 e
Storage temperature range ..... ; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. - 65°C to 150 °e

SN54AS2645 SN74AS2645
VIL Low-Ivel input volta

Texas Instruments - TTL DataBook Vol3

Uploaded by

Copyright:

Available Formats

Texas Instruments - TTL DataBook Vol3

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Texas Instruments - TTL DataBook Vol3

Uploaded by

Copyright:

Available Formats

SDAD001A

. Advanced Low-Pow~r Schottky

The TTL Data Book

Texas Instruments reserves the right to make changes at

TI cannot assume any responsibility for any circuits shown

Information contained herein supersedes data published in

Copyright © 1984 Texas Instrumems Incorporated

• Reduce system power requirements

• Reduced system component count

• Improve input threshold and noise margins

• 16-bit by 16-bit universal multiplier

IL-:_M_e_c_h_an_i_c_ClI_.• O_·._at_a_···~_ _. _.~~................

SN54ALSOOA SN74ALSOOA ................ 2-3 SN54ALS153 SN74ALS153 ............... 2-125

SN54AS282 SN74AS282 ............... 0 2-277 SN54ALS620A SN74ALS620A .0.0 ••••••• 0. 2-415

2-327 SN54AS643 SN74AS643 2-445

SN54ALS644A SN74ALS644A 2-445

SN74AS644 ............... '

SN54ALS521 SN74ALS521 ............... 2-333 SN54AS645 SN74AS645 2-445

SN54ALS522 SN74ALS522 ............... 2-333 SN54ALS646 SN74ALS646 ............... 2-455

SN74AS1032 .0.0.··0.0 ••••

SN54AS850 SN74AS850 • .0 •• 0 '0' •••••• 2-571 SN54ALS1241 SN74ALS1241 .............. 2-699

PART I - OPERATING CONDITIONS AND CHARACTERISTICS (IN SEQUENCE BY LETTER SYMBOLS)

f max Maximum clock frequency

ICCL Supply current, outputs low

10L Low-level output current

lOS Short-circuit output current

* Current out of a terminal is given as a negative value.

High-level input voltage

Input clamp voltage

tdis Disable time (of a three-state output)

ten Enable time (of a three-state output)

*Current out of a terminal is given as a negative value.

tpd Propagation delay time

G') tpHL Propagation delay time, hlgh-to-Iow-Ievel output

tpZL Enable time (of a three-state output) to low level

tsr Sense recovery time

tsu Setup time

Pulse duration (width)

PART II - CLASSIFICATION OF CIRCUIT COMPLEXITY

Gate Equivalent Circuit

large-Scale Integration, lSI

Medium-Scale Integration, MSI

The following symbols are used in function tables on TI data sheets:

H high level (steady state)

PARAMETER MEASUREMENT INFORMATION

G) LOAD CIRCUIT FOR

s: :- tsu ....J- th i : - - tw --1 3.5 V

o VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS

FREE-AIR TEMPERATURE INPUT RISE & FALL TIMES

"~ / ...V ~ ...........-

:xJ Input Rise and Fall Times-ns

GATES AND INVERTERS

SCHMITT·TRIGGER POSITIVE·NAND GATES AND INVERTERS

Dual 4-lnput Gates '21

Inverting & Non-Inverting Elements.

• Denotes available technology,

GATES, EXPANDERS, BUFFERS, DRIVERS, AND TRANSCEIVERS

_ _ 4-Wide 4-2-3-2-lnput '124H

:xl '23 Buffers/Drivers

TECHNOLOGY Octal Transceivers