MONARCH POLYUREA HB 1010

POLYUREA HB 1010 is a very fast set, rapid curing, flexible, two component
hybrid polyurea system. It is derived from a reaction of an isocyanate prepolymer
and an amine terminated resin blend. It can be applied as an economic
waterproofing and coating alternative to pure polyurea products. The material must
be applied utilizing high pressure, heated plural component spray proportioning
equipment. Polyurea HB 1010 conforms to
requirements of the EN 1504-2 standard (concrete
surface protection systems).

Properties
 Economic alternative to pure polyurea products
 Fast reactivity and return to service time
 100% solid, VOC free, no solvents
 Environmentally friendly
 Seamless coating
 Very good tensile and structural strength
 Excellent adhesion on concrete, steel, aluminum, plastics, fibers, wood, foam etc.
 Excellent flexibility
 Excellent crack bridging properties
 Variable application thickness possible
 Broad color spectrum

Applications Area
 General waterproofing under ceramic, screed concrete, marble and other floor coverings
 General waterproofing for light foot traffic areas like roofs, balconies, terraces, walkways
and public areas
 Waterproofing of ground concrete and load bearing walls
 Play grounds and decorative applications
 On thermal insulation products for waterproofing (polyurethane foam, EPS, XPS etc.)

INSTRUCTIONS
Surface preparation strongly affects coating performance. Concrete substrates must be prepared
mechanically using abrasive blast cleaning to remove cement laitance and achieve an open textured
surface. Weak concrete must be removed and surface defects such as voids must be fully exposed.
Repairs to the substrate, filling of blowholes/voids and surface leveling must be carried out using
appropriate products. All dust, loose and friable material must be completely removed from all
surfaces before application of the product, preferably by brush and/or vacuum. For application pull
off strength of the surface should be min. 1.5 N/mm² and concrete residual moisture should be max.
4% pbw (with appropriate moisture tolerant primer should be max. 6% pbw). The moisture content
should be measured by moisture meter. Be aware of condensation; the substrate must be at least 3
°C above dew point to reduce the risk of condensation of the coating. Relative air humidity for
application should be lower than 85%. Prior to application, confirm substrate moisture content,
relative air humidity and dew point.

1
 MONARCH POLYUREA HB 1010

Application conditions/ limitations:

Surface Temperature Ambient Temperature Relative Air Humidity

Priming:
The application surface has to be primed in order to achieve an even surface and good adhesion.
Lightly spreading out with quartz sand 0,3-0,8 mm is recommended because this provides higher
adhesion values and extends the maximum waiting time of primer prior to the application of
polyurea coating. In order to avoid the formation of blisters do not spread to excess.

Polyurea Application:
The polyurea must be applied within 12-24 hours of applying the primer. Isocyanate prepolimer and
amine resin must be applied using a two component high pressure and heat spray machine. The
machine should be able to spray the components in 1:1 volume ratio. Both components must be
heated above 70 °C. In order to achieve good performance, the temperature and pressure should
stay same during the application and must be controlled regularly. Polyurea system components
might not diluted under any circumstances. Before application, amine component must be stirred at
least 30 minutes using a barrel mixer until a homogenous mixture and colour obtained. Aromatic
polyurea coating systems are UV stable but are not color stable. The cured coating may exhibit
discoloration when exposed to sunlight. This does not influence the performance and physical
properties of the material. If the color stability required, an aliphatic top coat must be applied within
12 hours of applying base coat.

CONSUMPTION OF COATINGS
Polyurea Coatings: ~1.2kg = 1 m2 @ 1mm Thickness

PACKAGING
225 kg A component
200 kg B component

2
 MONARCH POLYUREA HB 1010

TECHNICAL PROPERTIES
PROCESS PROPERTIES
UNIT DATAS
By Volume A=100 B=100
Mix ratio
By Weight A=122 B=100
Process Temperature °C A: 60-70 B: 60-70

Process Pressure Bar A: 180-200 B: 180-200

COMPONENT PROPERTIES
Unit Method ISO component(A) Amine Component (B)
Density gr/cm3 ASTM D 1217 1,11±0,03 1,02±0,02

Viscosity mPa.s ASTM D 4878 700-800 300-600

Shelf Life --- --- 9 months 9 months

PHYSICAL PROPERTIES
METHOD DATAS
Chemical structure gr/cm3 A: MDI Prepolymer B: Amine Resin
VOC content (%) ASTM D1259 0
Solid content (%) ASTM D2697 100
Gel time (sec) --- 5-10
Tack free time (sec) --- 15-30
Recoat time (hr) --- 0-12 (without any pretreatment)
Density (gr/cm3 ) ASTM D792 0,99-1,03
Tensile strength (MPa) ASTM D638 ≥15
Modulus (MPa) ASTM D638 %100 elongation ≥ 5
Elongation at break (%) ASTM D638 ≥350
Hardness (Shore A) ASTM D2240 90-95
Tear strength (N/mm) ASTM D-624 ≥25
Taber abrasion (mg) EN ISO 5470-1 ˂250 (H22, 1000 cycle)
Impact resistance EN ISO 6272-1 Class III
Pull off strength (N/mm2 ) ASTM D4541 Concrete: ≥3 Steel: ≥6