Planos 9978

Drill Master DML-LP
No. 0000 0099 78

Rev. 001 |
Valid for: US009978
© Copyright 2020, Epiroc Drilling Solutions LLC, USA
Any unauthorized use or copying of the contents or any part thereof is prohibited.
This applies in particular to trademarks, model denominations, part numbers and drawings.
Table of Content
Electrical Diagram................................................................................................5
SCHEMATIC,ELEC, / ............................................................................................................. 6
SCHEMATIC DIAGR / .......................................................................................................... 23
SCHEMATIC,ELEC- / ........................................................................................................... 27
Hydraulic Diagram............................................................................................. 29
SCHEMATIC,HYD 3 / ........................................................................................................... 30
SCHEMATIC,AIR R / ............................................................................................................ 32
3
4
Electrical Diagram
LIST OF CONTENTS
Part no Description Remarks Page
2658369444 SCHEMATIC,ELEC, 6 - 22
2658597735 SCHEMATIC DIAGR 23 - 26
2657665382 SCHEMATIC,ELEC- 27 - 28
5
8 7 6 5 4 3 2 1
REV ECO/CN CHANGE APPRV
STARTER RELAY 1 (NOT USED ON MTU)

ZONE REVISIONS DATE
GEAR BOX / TOWER SUP. ON COOLER

NO NO BY BY
AIR END / REAR SIDE ON COOLER

REFER TO ARCHIVED DRAWING FOR PREVIOUS
STANDARD NIGHT LIGHT PACKAGE
COMP. DISCHARGE TEMP. SENDER

REVISION HISTORY.
DUST COLLECTOR SIDE WALKWAY
COMP. DISCHARGE TEMP. GAUGE

12 LIGHT PACKAGE (OPTION)
ALL ADDED WIRE CALL OUTS FOR C27 TIER4
QSX 15, TIER 3 AND 4 ONLY

BATTERY EQUALIZER OPTION
CROSSHEAD DUST COLLECTOR

USS20 UPDATED WIRE CALLOUT FOR DHD
PRO-HEAT HOT BOX OPTION
PLATFORM REAR D.C. SIDE

022 SHT-6,C8 02989 MODIFIED DHD CIRCUIT
01/24/20 NK BF
PLATFORM REAR CAB SIDE

SHT-3,D2&D6 ADDED SV COIL FOR BRAKE RELEASE SOLENOID
OPTION ON TIER 2& 3
OPTION ON TIER 2& 3

STANDARD ON TIER 4
24V OUTLET (OPTION)
STANDARD ON TIER 4
(NOT USED ON MTU)
(NOT USED ON MTU)

BATTERY JUMPER CONNECTOR
STARTER RELAY 2
STARTER No. 2
TOWER BOTTOM
2657007411, 2657007429
REC/SEP END
ETHER START
ALTERNATOR
POWER PACK
FUEL GAUGE
D
STARTER 1
CAB LIGHT
TOWER TOP
F.W.MURPHY
HOURMETER
POWERVIEW
WALKWAY
CAB END
SYSTEM
5
5
FOR CUSTOMER USE
FUEL LEVEL SENDER

201 TO CONSOLE
120 ^
G
G
STARTER
STARTER
ENGINE OIL PRESS.ENGINE WATER TEMP. VOLTMETER (OPT) ENGINE TACHOMETER

M
M
B1
ALT
2 5
1 6
3 4
MURPHY
B
S2A
S2A
S1A
S2
S2
S1
ES
2A
2 5
1 6
3 4
A
5
9
B
B
EJB
FUEL GAUGE
+
GND
3
35A
BATTERIES
2657409104
201
35
24V OUTLET
180
12V
30
FUSIBLE LINK
FUSIBLE LINK
FUSIBLE LINK
FUSIBLE LINK
30 AMP FUSE
S1A
S1
2 5
1 6
3 4
MURPHY
B
24V
ETHER
7
+
2 5
1 6
3 4
A
8A
C
HEAT
8A
8A
PRO
200 BLK
2C
199 GRN
SEE MTU ENG
2C
INLINE FUSE
180A QSX TIER 4 ONLY SEE SHEET 8
8A
WIRING SHT 12
198 RED
B4
2
ZONE C8
15 AMP
F
T
T
197 WHT
CIRCUIT LOCATED ON SIDE OF HYDRAULIC TANK

8A
BATTERY SELECT SWITCH
HYDRAULIC PUMP SUCTION PROTECTION VALVES

OFF - 1 - BOTH - 2
2 5
1 6
3 4
(IN CONSOLE)
MURPHY
B
OPEN VALVES TO COMPLETE ENGINE START
23
1
PX1
2
TIMER
F
T
2 5
1 6
3 4
A
24
B2
B2
12
H
START BUTTON
24 VDC TO 120 VAC
2 5
1 6
3 4
MURPHY
B
165
165
165
165
165
165
29
29
29
29
29
29
7A TO START BUTTON
QSX15 TIER 4 ONLY
ALL OTHERS, ROUTE
TEMPERATURE 2657446734
2 5
1 6
3 4
COMPRESSOR DISCHARGE
7A
A
SEE SHEET 8
INVERTER
6
39
R1
G
28C
ROUTE B4 DIRECT TO
B2
S
MICROWAVE
(OPTIONAL)
BATTERY IF BATTERY
WARNING LIGHT TEST BUTTON
6
I
SELECTOR SWITCH IS
29
2654651187
B2
INDICATOR LAMP TEST

NOT USED.
5
7B
INLINE FUSE
165
J1939 HI POWERVIEW
4
2 5
1 6
3 4
MURPHY
B
SWITCH (OPTION)
20 AMP
DRILL LIGHTS
INTERLOCK
POSITION
3
B
TRAM LIGHTS
DRILL
6
2 5
1 6
2
3 4
A
R7
SHIELD
1
J1939
7 8
J1939 LO
37 38 SHLD
NOTES:
TO ENGINE
SCHEMATIC
22
C
1 PART NUMBERS ARE FOR REFERENCE ONLY. CHECK B.O.M. FOR CORRECT PART NUMBER.
15 Amps
B
2 MODE SELECTOR SWITCH MUST BE IN "DRILL MODE" TO START ENGINE.
CB5
3 ROTATION AND PULLDOWN PROPORTIONAL CONTROLLER MUST BE IN NEUTRAL POSITION TO START
A
2657760555
POWERVIEW
HARNESS
MURPHY
ENGINE.
120 ^
4 ALL DIODES ARE RATED TO 600PIV, 3 AMP.
164
28
5 N.O. CONTACT HELD CLOSED WHEN CAROUSEL IS IN STOWED POSITION
KEY SWITCH
20 Amps
20 Amps
50 Amps
6 LIMIT SWITCH ON CAM SHAFT OF OEM CONTROLLER TO DETECT PULLDOWN CONDITION.
CB7
CB6
CB8
7 MODE SELECT SWITCH: JACK, HOIST, TOWER PINNING FUNCTIONS ARE ENABLED ONLY IN DRILL
7
7
7
MODE.
7
7
8 IF REMOTE PROPEL IS NOT USED,
ROUTE WIRE 73 TO R3 PIN 6
2
2
2
B2 B2 108A 1 6
6
1
180A

9 SWITCHES FROM DRILL CONTROLLERS TO PROPEL CONTROLLERS.
10 ADD JUMPER BETWEEN WIRE #98 AND #106 IN ELECTRICAL BOX WHEN RIG DOES NOT GET 'NO
B2
BUMP' OPTION. (SEE SHEET 4 C-8 AND NOTE 15 WHICH IS ALSO PART OF 'NO BUMP' OPTION)
11 STROBE LIGHT "ON" DURING TRAMMING ONLY.
B2
12 CARRY GROUNDS AND SHIELDS STRAIGHT TO CAB AND GROUND ONLY IN CAB. SHIELDS TO BE
13
FLOATING ON COIL END.
FOR JACK/PROPEL INTERLOCK OPTION, DELETE RELAY R8 IF THIS OPTION IS NOT USED.
E
D
CWP/AWS-02/8620-FC31
CWP/AWS-2/5-SM/FC-01
WARNING
EXPORT OF THIS DRAWING TO COUNTRIES
A
C OUTSIDE OF THE U. S. IS SUBJECT TO U. S.
CWP/AWS-02/5SA-08
EXPORT ADMINISTRATION REGULATIONS
14 LIMIT SWITCH USED TO KEEP CAROUSEL FROM CLOSING ON POWER HEAD, (NO BUMP) ADD JUMPER B CWP/AWS-05TSM/FC-01
BETWEEN WIRE #129 AND #129A IN CONSOLE WHEN RIG DOES NOT GET NO-BUMP} COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
O 1in DRAWN BY JRD/DRR
A CWP/AWS-02GM-42
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 05/26/2010
LETTER EPIROC DRILLING SOLUTIONS INFORMATION, IS THE PROPERTY OF EPIROC DRILLING
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY J. DENK
15 PD = POWER DISTRIBUTION CENTER NEAR BATTERY BOX SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE. DIM (IN)
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE 05/26/2010 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
PART AS INDICATED BY THE "LETTER DESIGNATOR" IN 24 UNDER 24 .01 .005
ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES ENG. APPVL. Q. DUNN
THE TAIL OF THE WELD SYMBOL. (CIRCULARITY)
TITLE
16 FOR ELECTRICAL SCHEMATICS OF CUMMINS QSX15 TIER 4i, CAT C15, C18 AND C27 TIER 4i, "NOTE" WELD SYMBOLS WITHOUT A LETTER DESIGNATOR
WILL CONFORM TO EPIROC DRILLING SOLUTION
THAT, EXCEPT AS AUTHORIZED IN WRITING BY EPIROC
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR 24 TO 120 .09
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE 05/26/2010 ELECTRICAL SCHEMATIC
MTU 10V1600 T4 AND WORLD ENGINE REFER 2658369444 REV 020. PROCEDURE CWP/AWS-02 SM/FC-01. ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET MFG. APPVL.
DOES NOT APPLY TO SUPPLIER OWNED DESIGNED PART
OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING. INFORMATION THEREIN; (2) NOT COPY THE DRAWING; (3) NOT 120 UP .12
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
THIRD ANGLE PROJECTION DATE DML/45/50
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI- (SQUARENESS)
FINISHED WEIGHT
17 FOR ELECTRICAL SCHEMATIC OF MTU 10V1600 AND 12V1600 TIER 4 FINAL PROCEDURES QUALIFIED IN ACCORDANCE WITH THE EPIROC
STRUCTURAL WELDING PROCEDURE CWP/AWS-02
DENTIAL OR TRADE SECRET INFORMATION THEREIN; AND (4)
UNLESS OTHERWISE SPECIFIED, PARALLELISM
SIZE D REF. NO. 2658316865 DWG.
NO. 2658369444 CR
UPON COMPLETION OF THE NEED TO RETAIN THE DRAWING, OR
REFER 2658397689 REV 005. AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1
UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF,
REMOVE ALL BURRS AND SHARP POSITION COMM.
WELD PROCEDURES AND ALL MATERIAL COPIED THEREFROM.
CORNERS AND COUNTERSINK
TAPPED HOLES TO BODY SIZE. CONCENTRICITY
SCALE NONE NO. 2658369444 SH
1 OF
17
6 8 7 6 5 4 3 2
Epiroc operated under the trademark 'Atlas Copco' prior to January 1, 2018 1
8 7 6 5 4 3 2 1
REV ECO/CN CHANGE APPR
ZONE REVISIONS DATE
NO BY BY
GEAR BOX / TOWER SUP. ON COOLER
FUEL AND COMP DISCH TEMP GAUGES

NO
CAT AND
CUMMINS
AIR END / REAR SIDE ON COOLER
SEE SHEET-1 FOR REVISIONS
STANDARD NIGHT LIGHT PACKAGE
DUST COLLECTOR SIDE WALKWAY

12 LIGHT PACKAGE (OPTION)
QSX 15, TIER 3 AND 4 ONLY
F.W. MURPHY POWERVIEW 380

BATTERY EQUALIZER OPTION
CROSSHEAD DUST COLLECTOR

PRO-HEAT HOT BOX OPTION
PLATFORM REAR D.C. SIDE
PLATFORM REAR CAB SIDE
SEE SHEET 13 FOR MTU

ENGINE START CIRCUIT
OPTION ON TIER 2& 3
OPTION ON TIER 2& 3
STANDARD ON TIER 4
STANDARD ON TIER 4
24V OUTLET (OPTION)
MICROWAVE (OPTION)
NCS STARTER RELAY
CS STARTER RELAY
COMP. DISCHARGE
TOWER BOTTOM
NCS STARTER
REC/SEP END
ETHER START
EARS OPTION
TEMP. GAUGE
D
ALTERNATOR
POWER PACK
HOUR METER
FUEL GAUGE
CS STARTER
CAB LIGHT
TOWER TOP
WALKWAY
CAB END
5
5
5
FULL 30 ^ ; EMPTY 250 ^
BATTERY JUMPER
COMP DISCH TEMP
FWM-ES2T-250 FUEL LEVEL SENDER

(IN CONSOLE)
1 6 3 5
2657007411
2657007429
S1
CONNECTOR
S2
ES
G
TIMER
STARTER
STARTER
M

7
S2A
S3
S4
S2
30 3
B
B
S
7
5
35A
24V OUTLET
7
35
5
ALT
ETHER
FUEL LEVEL
TO CONSOLE FOR
+
GND
1 6 3 5
CUSTOMER USE
S1
S2
BATTERIES
9
SHEET 13
201
200 BLK
TO MTU
12V
199 GRN
8A
8A
8A
150 Amps
8A
198 RED
24V
120 ^
197 WHT
12
8A
CIRCUIT LOCATED ON SIDE OF HYDRAULIC TANK
ENGINE TEMP. ENGINE TACH.

HYDRAULIC PUMP SUCTION PROTECTION VALVES
+
9
F
F
T
OPEN VALVES TO COMPLETE ENGINE START
2 5
1 6
3 4
MURPHY
B
23
PX1
BATTERY SELECT SWITCH
HEAT
OFF - 1 - BOTH - 2
PRO
2 5
1 6
3 4
F
24
T
A
1
INLINE FUSE
8
15 AMP
START BUTTON
2 5
1 6
3 4
MURPHY
B
J1939 LOW PIN 34
4B
4
2 5
1 6
3 4
J1939 HIGH PIN 35
A
DRILL POSITIONQSX15 TIERS 4i& 4F ONLY
165
165
165
165
165
165
7A TO START BUTTON
ALL OTHERS, ROUTE
REC 9B
REC 9G
SEE SHEETS 8 & 13
INTERFACE
29
29
29
29
29
29
7A
BOARD
OIL PRESS.
EARS
WARNING LIGHT TEST BUTTON
29
28C
2 5
1 6
3 4
MURPHY
B
R1
B1
30 Amps
30 Amps
REC CB3
REC CB4
8
INDICATOR LAMP TEST
TRAM LIGHTS
2 5
1 6
3 4
A
SWITCH (OPTION)
GND PIN 78
PVG
PVP
RSH
165
24 VDC TO 120 VAC

REC
24V
7B
UNSWITCH 24V PIN 77
RSL
5
MICROWAVE
(OPTIONAL)
REC 24V
INVERTER
12 1
11 2
10 3
8 5
7 6
9 4
ROUTE B4 DIRECT
DRILL LIGHTS
SWITCHED 24V PIN 76
B
POWERVIEW 380
TO BATTERY IF
INTERLOCK
AT REC
6
BATTERY
R7
MURPHY
SELECTOR SWITCH
50 Amps
8
IS NOT USED.
HOUR METER
37 38 SHLD
-
TO ENGINE
SCHEMATIC
H
+
6 1
5 2
4 3
15 Amps
CB5
164
28
39
22
6
FOR C15 T4F / QSX-15 T4F WITH REC BOX
KEY SWITCH
J1939-
6
J1939+
20 Amps
20 Amps
20 Amps
50 Amps
120 ^
CB7
CB6
CB8
CB9
B
A
1
2
7
7
REC CB1REC 9F
6
6
30 Amps
1
REC
24V
24V
REC
E
D
CWP/AWS-2/5-SM/FC-01 EXPORT OF THIS DRAWING TO COUNTRIES

WARNING A
CWP/AWS-02/5SA-08
B CWP/AWS-05TSM/FC-01
COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
A CWP/AWS-02GM-42
SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE. DIM (IN)
.06 ROUNDNESS
TITLE
"NOTE" WELD SYMBOLS WITHOUT A LETTER DESIGNATOR
PROCEDURE CWP/AWS-02 SM/FC-01.
24 & UP
ANGLES
.03
0 30'
.005
ANGULARITY
DATE
MFG. APPVL.
05/26/2010 ELECTRICAL SCHEMATIC
ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
PROCEDURES QUALIFIED IN ACCORDANCE WITH THE EPIROC
NO. 2658369444 CR
AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1 REMOVE ALL BURRS AND SHARP POSITION
UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF, COMM.
2 OF
17
7 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
STROBE LIGHT ON PLATFORM REAR OPTION

ZONE REVISIONS DATE
NO NO BY BY
PROPEL MODE INDICATOR LIGHT OPTION
PROPEL MODE, CAB SIDE, MAIN PUMP

BRAKE RELEASE SOLENOID DR/PR
PULLDOWN CONTROLLER INTERLOCK
BRAKE RELEASE SOLENOID DR/PR

PROPEL DRILL SOLENOID VALVE
(SPRING RETURN TO NEUTRAL,

STROBE LIGHT ON CAB OPTION
NEUTRAL DETECT, ROTATION

SPRING RETURN TO NEUTRAL
REMOTE PROPEL OPTION
3 SPEED DIRECT DRIVE

PROPEL SELECT RELAYS
ROTARY HEAD OPTION

CENTER LOCKING)
START INTERLOCK
JACK INTERLOCK
CENTER LOCKING
D
PROPEL ALARM
PROPEL MODE
MAIN PUMP
D.C.SIDE
5
5
1
1
R13
R12
R14
9
SV
R3
SV
R4
SV
Y
Y
G
5
0
0
11
D13
2 2
D4
3 3
-
D5
+
1
1
B
B
A
X
2
70B
21C5 GREEN/YELLOW
2
21C5 GREEN/YELLOW
R5
R6
HIGH SPEED
MID SPEED
0
0
185
184
81
5
5
5
70B
105A
73
104A
54
S1
S2
70B
72
71
81
70A
74
53
K
INTERLOCK
BROWN
PROPEL
4
8
75
R9
G F
8
215A BLUE
7
3
R12
R13
2
53A
215B
77
4
57
3
7
R13
R12
70C
8
H
8
79B
8
4
54A
GROUND
GROUND
R12
R13
C
8
4
LATCHING RELAY
LATCHING RELAY
INTERLOCK
13
13
CAB
CAB
76
6
9
6
2
4
R12
R13
JACK
R4
R4
R8
R3
R3
96
50
51
2
8
8
4
4
E
5
5
5
5
36B
M
95
8F
8
4
CW 5SH
CW 5SH
12
12 5SH
5SH
12
11
11
RESET 12
RESET 12
SET 14
SET 14
R3
R3
R4
R4
DN/F'WD
UP/B'WD
E-STOP
2
7
3
F'WD
B'WD
12
CCW
CCW
ROD SUP.
70A
RETRACT
1
1
1
1
2
2
2
2
1
58
79
1
60
R7
8E
36A
L
59
0
213A
216A
0-500 ^
213
215
215
214
90
HOLDBACK VALVE
6
6
R11
80G
R2
J
R10
8
100
U.T.DECEL
20
D
61
SV
89
50 ^
B
82
81
DRILL POSITION
79A
216
59
DRILL/PROPEL
Multifunction Control
Multifunction Control
FRICTION HOLD CENTER LOCK
SPEED REDUCER
A
OX
XO
OX
XO
-
OX
PULL DOWN / DRILL MODE

+
216A
B
B
R
R
A
215
214
213
216
C
7
7
B
19
TOGGLE SWITCH
MICROSWITCH
3 POSITION
NO
NC
H
L
ON HANDLE
ON HANDLE
8
8
BUTTON
BUTTON
6
R6
9
NEUTRAL DETECT
8
COM
FRICTION
RATATION /
DRILL MODE
CENTER LOCK
HOLD
17
70B
70B
3
SPEED
REDUCER
NUTRAL
DETECT
3
70B
80
6
82
82
82
82
R5
80 82
82
8
20 Amps
80
CB3
7
7
6
6
D
E CWP/AWS-02/8620-FC31
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1 REMOVE ALL BURRS AND SHARP
SEE SHEET 1 FOR NOTES. UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF, POSITION COMM.
3 OF
17
8 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
HIGH PRES. AIR THROTTLE OPTION

ZONE REVISIONS DATE
NO NO BY BY
PROXIMITY SWITCH AND RELAY R15 IN
PROXIMITY SWITCH PS7 AND R16 IN

PULLDOWN FORCE LIMIT (NO BUMP)
TRAM INTERLOCK DECEL (OPTION)
CAROUSEL ROD INDEXING

PLACE OF LIMIT SWITCH LS4
TOWER UNPINNED INDICATOR

PROXIMITY SWITCH PS5 IN
PROXIMITY SWITCH PS6 IN
ROD SUPPORT OPTION

PULLDOWN FEMA ACTUATOR
ROD SUPPORT RETRACTED
BREAKOUT WRENCH
CAROUSEL SWING
TOWER PINNING
CHAIN WRENCH
DRILL FEED FORCE
CAROUSEL STOWED
ROTARY HEAD UP
FEED UP DECEL
D
LIMIT SWITCH
CLOSE VALVE
OPEN VALVE
ROTATE CCW
DISENGAUGE
ROTATE CW
LOADING
RETRACT
RETRACT
RETRACT
ENGAUGE
STOWED
EXTEND
EXTEND
EXTEND
5
5
SET FOR PULLDOWN PRESSURE OF 1000 PSI
R
1
1
R11
R10
R9
G
9 SPOOL, SECT. 1
9 SPOOL, SECT. 2
9 SPOOL, SECT. 3
9 SPOOL, SECT. 6
9 SPOOL, SECT. 8
9 SPOOL, SECT. 9
9 SPOOL, SECT. 4
0
DPV
DPV
DPV
DPV
DPV
DPV
DPV
C1
C1
C1
C1
C1
C1
C1
1
C2
C2
C2
C2
C2
C2
C2
A
R2
PA
0
0
82A
62
33A
129A
98
5
129A
128
82A
98
62
T2
T2
117
121
123
126
34
23
1
116
8
122
120
127
R15
R16
R10
LS5
LS6
LS7
LS4
PS5
PS6
FROM SHT-7
R15
R16
SEE SHEET 5 FOR SECTIONS 5 AND 7 OF THE 9 SPOOL.

T3
T3
LS8
6
6
7
4
0
0
C
NC
80 T1
82 T1
129
6
80
106
129
14
78
82
106
33
78
-
W122
KNOB
94
308
309
B
93
TOP TERMINAL
TOP TERMINAL
X
TERMINAL
TERMINAL
T2
T2
106
BOTTOM
BOTTOM
A
PS4
PS7
DRILL
FORCE
T3
T3
+
FEED
T1
T1
RETRACT
EXTEND
-
-
UNPINNED
PINNED
B
B
CKT
CKT
CKT
CKT
CKT
78
X
MOUNT IN CONSOLE
CONTROLER
CAROUSEL
PRESSURE
THROTTLE
INDEXING
BREAKOUT
A
A
CONTROL
CONTROL
CONTROL
CONTROL
WRENCH
0-500 ^
SWING
CHAIN
+
+
HIGH
FORK
ROD
B
RES2
SPRING
SPRING
SPRING
SPRING
SPRING
LOCKING
LOCKING
LOCKING
LOCKING
LOCKING
RETURN
RETURN
RETURN
RETURN
RETURN
CENTER
CENTER
CENTER
CENTER
CENTER
50 ^ 78A
82
82
82
80
82
82
82
82
82
82
82
82
82
82
80 82
80 82
7
7
6
6
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0 30'
.005
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
4 OF
17
9 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
NON-DRILL END JACK RETRACT INDICATOR
JACK RETRACT/PROPEL INTERLOCK OPTION

ZONE REVISIONS DATE
NO NO BY BY
D.C. SIDE JACK RETRACT INDICATOR
CAB SIDE JACK RETRACT INDICATOR

NON-DRILL END JACK CONTROL
DUST COLLECTOR (BOTTOM COIL)

D.C. SIDE JACK CONTROL
WATER INJECTION (TOP COIL)

CAB SIDE JACK CONTROL
VARIABLE FAN SPEED OPTION

HOLD BACK CONTROL OPTION
TOWER RAISE/LOWER
RETRACT (BOTTOM COIL)
OR (BOTTOM COIL)
OR (BOTTOM COIL)
PARKING BREAK OPTION

LOWER (BOTTOM COIL)
LOWER (BOTTOM COIL)
TORQUE LIMIT OPTION

HOIST CONTROL
EXTEND (TOP COIL)
EXTEND (TOP COIL)

RAISE (TOP COIL)
RAISE (TOP COIL)
EXTEND (TOPCOIL)
TEST LAMP OPTION
TEST LAMP OPTION
TEST LAMP OPTION
TEST LAMP OPTION

D
PULSE TIMER
RETRACT
RETRACT
OPTION
5
5
R
R
6 SPOOL, SECT. 1
6 SPOOL, SECT. 2
6 SPOOL, SECT. 3
6 SPOOL, SECT. 5
6 SPOOL, SECT. 6
6 SPOOL, SECT. 4
D10
D15
D9
28C
28C
28C
1
DPV
DPV
DPV
DPV
DPV
DPV
C1
C1
C1
C1
C1
C1
C2
C2
C2
C2
C2
C2
R8
SV
G
G
D8
0
69B
D2
183
171
170
D14
91
92
87
88
85
86
83
84
PULSE TIMER PCB
TIMER
28C
69A
C
69
-
134
67
65
66
3A
B
B
CKT
CKT
CKT
CKT
CKT
80
131
WATER INJECTION
X
X
NON-DRILL
LOWERING
A
A
CONTROL
RAISING
CONTROL
CONTROL
CONTROL
CONTROL
-
HOIST
TOWER
+
+
D.C.
SIDE
JACK
JACK
SIDE
JACK
END
CAB
KNOB
KNOB
KNOB
KNOB
SPRING
SPRING
SPRING
SPRING
SPRING
LOCKING
LOCKING
LOCKING
LOCKING
LOCKING
OOX
XOO
RETURN
RETURN
RETURN
RETURN
RETURN
CENTER
CENTER
CENTER
CENTER
CENTER
A
FEMA
FEMA
FEMA
B
B
PA
PA
PA
OFF
0
X
X
118
112
183
124
D.C./PULSE
INJECTION
A
CONTROL
CONTROL
CONTROL
CONTROL
PARKING BREAK
TORQUE
WATER
LIMIT
SPEED
+
+
181
182
HOLD
BACK
LS3
FAN
ON/OFF
133
182A
181
LS1
65A
LS2
B
LS3A
181
182
82
82
80
80
80
80
80
80
80
80
82
82
82
80
80 82
80 82
7
7
6
6
E
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0 30'
.005
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
5 OF
17
10 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
DHD OPTION RETURN TO TANK SOLENOID

PRESSURE SWITCH DHD FLOW INDICATOR
NO NO BY BY
TELESCOPING DUST HOOD OPTION
INCLINOMETER OPTION (ON TOWER)

DHD OPTION PUMP SOLENOID VALVE
YELLOW STROBE ON TOWER OPTION

A/C COMPRESSOR CLUTCH OPTION
BLUE STROBE ON TOWER OPTION

ANTI-RUMBLE SOLENOID VALVE
HEATER/PRESSUREIZER MOTOR
STRATA-LOGGER PLUS OPTION

RACOR FUEL HEATER OPTION
ROTARY HEAD TACH. OPTION
STRATA-LOGGER 2 OPTION
DRILLING EFFICIENCY
DUST FLAP OPTION
FRONT WASHER PUMP
WATER DUMP OPTION
REAR WASHER PUMP
INDICATOR OPTION
DHD LUBE OPTION
HORN ON ROOF
FRONT WIPER
FRONT WIPER
RAISE
LOWER
DOWN
UP
5
5
5
A/C CLUTCH
SV
21C
PULLDOWN PRESS. SENSOR

300W
300W
TORQUE PRESS. SENSOR

-
RECLOSE AT 240psi
ROTATION TACHOMETER
STROBE
OPEN AT 325psi
A/C COMPRESSOR
DISCHARGE PORT
AIR PRESS. SENSOR

HIGH PRESS.
Y
LOCATED AT
21C
PS
R
WIPER MOTOR
WIPER MOTOR
+
WINDOW
WINDOW
114
OPENS AT 75 $ F.
OPENS AT 75 $ F.
STROBE
DRILL AIR PRESSURE

B
B
A
B
21B
INDICATOR SWITCH
115
DOWN (E)
P
UP (R)
PRESSURE SWITCH
203
9 SPOOL, SECT. 5
9 SPOOL, SECT. 7
ON MANIFOLD
21B
C
WASHER PUMP
WASHER PUMP
PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6
USED
TANK SOLENOID
NOT
RE-OPEN AT 6psi
CLOSE AT 34psi
DPV
DPV
C1
C1
DISCHARGE PORT
C2
C2
-
WP
WP
RETURN TO
VACUME SWITCH BLUE

LOW PRESS.
LOCATED AT
EVAPORATOR
21B
CAP OFF RED WIRE

MAG PICKUP IN ROTARY HEAD
GND
S
+
EMB
114C
BLOWER
21A
DHD TIMER
GND
21A
COMPUTER DOWNLOAD
209
115A
TIMER CONST.
24V
OUT
RESERVOIR
RESERVOIR
CAB21
CAB22
CAB23
CAB1
CAB2
DIB
CAB3
WD
WD
THERMOSTAT
109
108
151
150
24V
OUT
HORN BUTTON
RESERVOIR
ON CONSOLE
PURPLE
24V
IN
BARE
HAND HELD
TERMINAL
LOCATED ON
DRILLER'S CONSOLE
68
DEI
114B
205
206
LOCATED IN CONSOLE
WIPER SWITCH
WIPER SWITCH
2
21
3
3
1
ROTORY SWITCH
HI
WINDOW
WINDOW
OFF
LOW
MED
4 POSITION
MDL 2
-
A/C ON/OFF
2 AXIS CONTROLLER
W
W
LUBE ON
WATER DUMP
B
ON/OFF
SIG
B
TACH
+ SIG
204
114A
18
40
(T4F)
ENCODER
(LOCATED IN TOWER)
18
RIGHT
FORWARD
BACK
LEFT
16
18
40
15 Amps
5 Amps
15 Amps
5 AMP
20 Amps
30 Amps
FUSE
CB12
CB10
CB2
CB4
CB9
80
80
80
80
80
82
6
7
6
6
80 82
80 82
7
7
6
6
E
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
6 OF
17
11 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
PNEUMATIC CONTROLLER,
SEE MANUAL FOR WIRING
LINCOLN CENTRO-MATIC
LINCOLN CENTRO-MATIC
AND SET-UP (OPTION)
WIRING AND SET-UP.

THREAD LUBRICATOR
WIRING AND SETUP)

CONTROL (OPTION)
(SEE MANUAL FOR

SEE MANUAL FOR
ELECTRIC PUMP
CONTROLLER,
D
PNEUMATIC
HYDRAULIC
(OPTION)
AUTOLUBE
5
5
DO NOT USE
BLUE (NC)
LOW PUMP
LEVEL SOLENOID
PRESSURE
PRESSURE
LOW LEVEL
LOW LEVEL
PRESSURE
SWITCH
SWITCH
GREY
BLACK
SOLENOID
SWITCH
SWITCH
BLUE
WHITE
BROWN
SWITCH
PUMP
(NO)
RED
(PURPLE)
COMMON
SIGNAL
DO NOT USE
DO NOT USE
COMMON
BLUE (NC)
BLUE (NC)
(NC)
(NC)
193 BLACK (COMMON)
193 BLACK (COMMON)

1 2 3 4 5
BLACK
(COMMON)
(COMMON)
RED (NO)
RED (NO)
PURPLE
PURPLE
80A
(NORMALLY OPEN)
PUMP SOLENOID
5
C
192
192
A1 A2
SV
M
V1 192A
191
191
C
RELAY
190
190
1
R17
196-196A BRIDGED
196A
11 14
196
AT 24V PANEL
193
192
11
11
21
19
18
17
16
15
13
12
10
21
19
18
17
16
15
13
12
10
14
14
+23
22
20
+23
22
20
24
24
1
1
9
8
7
6
5
3
2
9
8
7
6
5
3
2
4
4
195 RED
194 RED
195 RED
194 RED
- -
14 14
13 13
202
8
R17
12 12
11 11
6
10 10
SENTRY CONTROL
SENTRY CONTROL
9 9
8 8
7 7
6 6 1 BLUE 5
JUMPER 1 1
5 JUMPER 5 2 80A
WIRES 2 2
WIRES BROWN
80A
5
4 4 3 190
WHITE 3 3
4
3 3 191 B
+-
+-
5
BLACK 4 4
2 2 GLC 2200 5 192
CONTROL 6 ORANGE 5 5
1 1 193
7 6 6
YELLOW 194
8 7 7
GREY 195
INLINE FUSE
9 8 8
10 RED
10 AMP
80
80
80
1
80 82
80 82
7
7
6
6
1
1
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
7 OF
17
12 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
ELECTRIC METZKE BREAKOUT WRENCH NO NO BY BY
THREAD GREASE
(OPTION) EARS OPTION (OPTIONAL) SEE SHEET-1 FOR REVISIONS
5
5
4B 4A
D
TG1
TIMER RELAY
M
RESET SOLENOID BREAK SOLENOID
3B 3A
OPEN SOLENOID CLOSE SOLENOID

141H2
2B 2A
SV
141H3
PRESSURE SWITCH
OPEN SOLENOID CLOSE SOLENOID

THREAD GREASE
TO ENG. SCHEM. 1B 1A
37 38
J1939 LOW PIN 34
J1939 HIGH PIN 35 DISENGAGE SOLENOID ENGAGE SOLENOID

INTERFACE
C
202
BOARD
EARS
12 11 10 9 8 7 6 5 4 3 2 1
16 PIN
GND PIN 78 REC PLUG
12 11 10 9 8 7 6 5 4 3 2 1
UNSWITCH 24V PIN 77 W122
W12
W11
W10
SEE SHT-3
W8
W7
W6
W4
W9
W5
W3
W2
W1
SWITCHED 24V PIN 76
THREAD GREASE OPTION
12 11 10 9 8 7 6 5 4 3 2 1
(NO)
TG1
14 PIN
ROUND PLUG
12 11 10 9 8 7 6 5 4 3 2 1
DISENGAGE
ENGAGE
CLOSE
BREAK
RESET
CLOSE
OPEN
OPEN
B
CONTROL BOX
LOWER JAWS
TOP JAWS
PEDESTAL
BREAKOUT
PILOT LIGHT
SWITCH
MASTER
80
80
1 6 7 80 82
1 6 7 80 82
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
8 17
OF
13 8 7 6 5 4 3 2 1
Epiroc operated under the trademark 'Atlas Copco' prior to January 1, 2018
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
CUMMINS QSX15 TIER 3 ENGINE SEE SHEET-1 FOR REVISIONS
COOLANT LEVEL SENSOR

IN ENGINE WATER TANK
UNSWITCHED GROUND
UNSWITCHED POWER
THROTTLE CONTROL
ENGINE SHUT DOWN

J1939 DATA LINK
J1708 DATA LINK
PANEL GROUND
EARS OPTION
D
5
5
5
50 PIN CONNECTOR
CONNECTOR
31 PIN
29
30
39
40
50
07
08
17
18
28
46
37
36
26
27
48
47
49
38
10
T
S
105
113
107
110
5
5
5
5
5
11
11
11
11
11
37
38
SHLD
26
27
7P
13
5P
36J
5
24V
24V
24V
24V
24V
ON TOWER OPTION
A B C
BATTERY
BATTERY
BATTERY
BATTERY
BATTERY
120 ^
GROUND
GROUND
GROUND
GROUND
GROUND
E-STOP
2
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
1
COOLANT LEVEL HIGH SIGNAL
COOLANT LEVEL LOW SIGNAL
COOLANT LEVEL RETURN
(18) (15) 36G

HYDRAULIC TANK
THROTTLE SIGNAL
THROTTLE RETURN
C
COLLANT LEVEL 5V
LOW LEVEL
THROTTLE 5V
E-STOP
TO BATTERY NEGATIVE TERMINAL 200E
5
J1939 DATA LINK SHEILD
J1939 DATA LINK HIGH
36F
J1939 DATA LINK LOW
J1708 DATA LINK LOW
CS OPTION
E-STOP
2
1
36D
11
11
NCS OPTION
E-STOP
2
FROM SHT 6
37 38
TIME DELAY RELAY FOR

HYDRAULIC TANK LEVEL
248 $ F RISING
SET TO 5 SECONDS
36C
(P.P.BOX)
A
37 38 SHLD
FROM SHT 1
2657474140
COOLANT
SENSOR
36B
LEVEL
SEE SHT 2 C-5

A
36B
B
C
36A
7
A2
R14A
IN CONSOLE
TIME DELAY
E-STOP
2
36A
(LHL)
8
Y1
36
A1
SHLD
CONTROLLER
DATA LINK
CONNECTOR
THROTTLE
11
37
38
26
27
CB1LOAD
5
5 Amps
HTD
9 PIN
36A
LINE
LEVELSWITCH
HYD. TANK
6
6
11
15 AMP
B2 B2
INLINE FUSE
11
15 AMP
INLINE FUSE
7
7
7
WARNING A
D
C
CWP/AWS-02/5SA-08
OUTSIDE OF THE U. S. IS SUBJECT TO U. S.
CUMMINS QSX15 TIER 3 ENGINE
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
9 17
OF
14 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
CAT C15, C18 TIER 3 & CAT C27 TIER 2 ENGINES

NO NO BY BY
ETHER START SOLENOID
UNSWITCHED GROUND
UNSWITCHED POWER
ENGINE SHUT DOWN
THROTTLE CONTROL
ENGINE SHUT DOWN

J1939 DATA LINK
D
SWITCHED POWER
FUEL PRIMER
5
5
5
3
R1
ES
1
70 PIN CONNECTOR
R1
4
PM
44
0
3
36J
42
34
50
10
48
52
53
49
61
63
65
70
44
66
ON TOWER OPTION
8
25
SHLD
8E
9E
38
37
11
11
11
107
105
113
15
E-STOP
PRIMER
2
EJB
1
5
COOLANT LEVEL SIGNAL
COOLANT LEVEL RETURN
36G
COOLANT LEVEL 8V
A B C
HYDRAULIC TANK
120 ^
C
119
LOW LEVEL
(18) (15)
E-STOP
J1939 DATA LINK SHIELD

J1939 DATA LINK LOW
CAT DATA LINK HIGH
CAT DATA LINK LOW
UNSWITCHED BATTERY 24V
EJB
36F
A
CS OPTION
E-STOP
2
SET TO 5 SECONDS
1
(P.P.BOX)
36D
NCS OPTION
JUMPER
E-STOP
2
1
248 $ F RISING
15
7P
5P
7
36C
37 38 SHLD
FROM SHT 1
A2
TIME DELAY
(LHL)
A
B
C
J1939 DATA LINK LOW
36B
Y1
A1
B
FROM SHT 6
SEE SHT 2 C-5

37 38
36B
36A
HTD
CONTROLLER
COOLANT LEVEL
SENSOR
7
THROTTL
R14A
IN CONSOLE
E-STOP
36A
2
LEVELSWITCH
8
HYD. TANK
1
36
9 PIN J1939
SHLD
SHLD
DATA LINK
CONNECTOR
9 PIN CAT
DATA LINK
CONNECTOR
CB1LOAD
5 Amps
37
38
8E
9E
38
37
5
5
IN CAB
36A
LINE
7
7
7
7
7
6
6
11
15 AMP
B2
INLINE FUSE
CAT C15, C18 TIER 3 & CAT C27 TIER 2 ENGINES A

E
D
WARNING
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
10 OF 17
15 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
CUMMINS QSK 19 TIER 2
UNSWITCHED GROUND TO ECM

UNSWITCHED POWER TO ECM
ENGINE THROTTLE CONTROL

J1939 DATA LINK
ENGINE SHUTDOWN
ETHER SOLENOID
D
CIRCUIT
5
ES
31 PIN ENGINE
23 PIN ENGINE
16 PIN ENGINE
SERVICE TOOL
3 PIN J1939
3
CONNECTOR
CONNECTOR
ON ENGINE
CONNECTOR
CONNECTOR
20
21
22
A
C
11
11
36J
7P
13
5P
37
38
SHLD
ON TOWER OPTION
107
COOLANT LEVEL SIGNAL 105
COOLANT LEVEL RETURN 113

THROTTLE SIGNAL
THROTTLE RETURN
E-STOP
2
THROTTLE 5V
1
COOLANT LEVEL 5V
C
(18) (15) 36G

HYDRAULIC TANK
LOW LEVEL
E-STOP
B
36F
UNSWITCHED POWER 24V
J1939 DATA LINK LOW
CS OPTION
E-STOP
2
SET TO 5 SECONDS
1
(P.P.BOX)
JUMPER
36D
NCS OPTION
E-STOP
2
1
FROM SHT 6
248 $ F RISING
37 38
36C
B
B
C
A2
TIME DELAY
B
(LHL)
37 38 SHLD
FROM SHT 1
36B
COOLANT LEVEL
SENSOR
2657807638
Y1
A1
CONTROLLER
THROTTL
SEE SHT 2 C-5
36B
36A
HTD
7
R14A
IN CONSOLE
E-STOP
36A
LEVELSWITCH
2
HYD. TANK
1
9 PIN J1939
2657651242
36
SHLD
DATA LINK
CONNECTOR
37
38
CB1LOAD
5
5 Amps
A
36A
LINE
7
7
7
6
6
15 AMP 11
B2
INLINE FUSE E CWP/AWS-02/8620-FC31

WARNING A
D
C
CWP/AWS-02/5SA-08
CUMMINS QSK 19 TIER 2
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0 30'
.005
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
11 OF 17
16 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
CUMMINS QSX15 TIER 4 FINAL ENGINE

ZONE REVISIONS DATE
NO NO BY BY
FUEL/WATER FILTER HEATER

AFTER TREATMENT SENSORS
REC HOSE HEATER RELAYS
BACK FLOW HOSE HEATER

PRESSURE HOSE HEATER
WATER IN FUEL SENSOR

SUCTION HOSE HEATER
DEF DOSING INJECTOR

DPF DELTA PRESSURE
DEF SUPPLY MODULE

UNSWITCHED GROUND
THROTTLE CONTROL
ENGINE SHUT DOWN

UNSWITCHED POWER
J1939 DATA LINK
STARTER LOCKOUT
CONTROL VALVE
PRIMER PUMP
DEF TANK
D
5
5
ECM CONNECTOR
86
PRIMER PUMP RELAY

25
26
27
28
49
50
51
52
73
21
45
76
83
41
42
35
32
61
64
10
33
16
54
79
81
57
82
38
39
40
84
85
77
53
13
62
21
22
23
24
1
R47
3
CUMMINS ENGINE
85
47
CAN+
CAN-
5
11
11
11
11
11
5
5
5
5
5
37
38
313
315
255
258
107
105
113
15
14
7P
13
5P
137A
141
146
152
136
153
147
154
135
142
143
144
155
155
149
145
138
148
36J
30
248 $ F RISING
24V
24V
24V
24V
24V
87
EJB
EJB
BATTERY
BATTERY
BATTERY
BATTERY
BATTERY
157
120 ^
C B A
85
87
R1
R21
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
UNSWITCHED
1
30
86
ON TOWER OPTION
SEE SHT 1
36H
E-STOP
2
136 SUPPLY MOD TEMP DRIVER
258 DPF OUTLET PRESSURE
255 DPF DELTA PRESSURE
113 OEM SENSOR RETURN
1
153 DEF REVERTING VALVE
146 PUMP MOTOR RETURN
152 PUMP MOTOR SUPPLY
147 TANK HEATER VALVE

C
15 THROTTLE RET 2
14 THROTTLE POS 2
107 SENSOR SUPPLY
13 THROTTLE POS 1
5P THROTTLE RET 1
107 SENSOR SUPPLY
141 PRESSURE SENSOR
113 OEM SNSR RETURN
HYDRAULIC TANK
36F (18) (15)36G

105 COOLANT LEVEL SIGNAL
107 SENSOR SUPPLY
LOW LEVEL
7P THROTTLE 5V
157 RELAY SUPPLY

113 OEM SENSOR RETURN
E-STOP
107 SENSOR SUPPLY
144 REC 4B
143 REC 4G
142 REC 4H
135 REC 4C
J1939 DATA LINK LOW
CS OPTION
155
155
155
138
147
154
142
143
149
145
148
144
E-STOP
2
5
REC R4
REC R3
REC R2
2
10
11
12
2
F
B
1
HEATER
DEF HEATER 1
DEF HEATER 2
DEF HEATER 3
DEF DOSER
WATER IN FUEL
SENSOR
36D 1
DEF TANK
HEATER VALVE
DEF SUPPLY
MODULE
REMOTE CON. E-STOP

SWITCH
DPF DELTA PRESSURE (SOOT)
# 4 $ C.
# 3 $ C.
SEE SHT 2 C-5
36D
7
R14A
THROTTLE
CONTROLLER
A
C
INLINE FUSE
30 AMP FUSE
R3
R2
R4
FROM TERM. 1 ON BAT. SELECTOR
36C
OPENS AT 18 $ C
CLOSES AT 1 $ C
8
11
36C
47
CAN+
CAN-
5
JUMPER
NCS OPTION
E-STOP
2
37 38 SHLD
47
FROM SHT 2
120 ^
CAN+
C B A
36B
CAN-
47
180A
A
EJB
87
R47
5
CAN+
CAN-
CAN-
CAN+
CAN-
CAN+
CAN-
CAN+
30
137
85
87
47
47
47
47
SHLD
DATA LINK
CONNECTOR
R20
5
5
36A
37
38
4
IN CONSOLE
5
30
47A
REC CB8 REC 10E
86
COOLANT LEVEL
SENSOR
2657807638
9 PIN
TANK HEADER
DEF
TEMPERATURE
SCR
TEMPERATURE
NOx SENSOR
E-STOP
A
180
REC CB14 REC 10B
REC CB16
1
15 Amps
15 Amps
36
REC CB7 REC 9D

CB1LOAD
5 Amps
10 Amps
7
30 Amps
LINE
6
7
24V 7 6
7
REC
REC
REC 5
WARNING A
D
C
CWP/AWS-02/5SA-08
OUTSIDE OF THE U. S. IS SUBJECT TO U. S. CUMMINS QSX15 TIER 4 FINAL ENGINE
HYD TANK TIME DELAY B CWP/AWS-05TSM/FC-01
LEVEL COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
(LHL) A CWP/AWS-02GM-42
SWITCH LETTER
DESIGNATOR
EPIROC DRILLING SOLUTIONS
PROCEDURE NO
INFORMATION, IS THE PROPERTY OF EPIROC DRILLING
DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY J. DENK
7 HTD 5 THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER
.06
2 PL 3 PL O 5 1O 15 2O 25 mm DATE 05/26/2010 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
Y1 A2 PART AS INDICATED BY THE "LETTER DESIGNATOR" IN
THE TAIL OF THE WELD SYMBOL.
ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES
24 UNDER 24 .01 .005
ROUNDNESS
(CIRCULARITY) ENG. APPVL. Q. DUNN
TITLE
7
TIME DELAY RELAY "NOTE" WELD SYMBOLS WITHOUT A LETTER DESIGNATOR
24 & UP
ANGLES
.03
0 30'
.005
ANGULARITY
DATE
MFG. APPVL.
A1 FOR HYDRAULIC TANK DOES NOT APPLY TO SUPPLIER OWNED DESIGNED PART
INFORMATION THEREIN; (2) NOT COPY THE DRAWING; (3) NOT UNSPECIFIED FILLETS PERPENDICULARITY
OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING. 120 UP .12
LEVEL SET TO 5 STRUCTURAL WELDING MUST BE DONE BY WELDERS AND DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
AND RADII TO BE .03 (SQUARENESS)
FINISHED WEIGHT
SECONDS (P.P.BOX)
NO. 2658369444 CR
SEE SHEET 1 FOR NOTES. WELD PROCEDURES AND ALL MATERIAL COPIED THEREFROM.
12OF 17
17 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
CAT C15/C18 TIER 4F SEE SHEET-1 FOR REVISIONS
AFTERTREAT. INTERCONNECT GRND
PETU POWER CONNECTION

FUEL PRIMER ECM CONTROL
HIGH SPEED REGEN ENABLE

LOW SPEED REGEN ENABLE
DIGITAL SENSOR RETURN
AIR INLET TEMPERATURE

COOLANT LEVEL SWITCH
ANALOG SENSOR RETURN
ELECTRONIC FUEL PUMP
ECM UNSWITCHED POWER

SWITCH INPUT RETURN
KEY SWITCHED POWER
D
SENSOR 8V SUPPLY
FUEL PRIMER PUMP
ENGINE SHUT DOWN

J1939 DATA LINK
CAT DATA LINK
ETHER START
ECM GROUND
5 (GROUND)
BATT+
BATT+
BATT-
BATT-
5
5
5
5
REC 9H
ES
5
3
5
70 PIN CONNECTOR
5
REC
R1
42
50
34
11
66
49
27
32
36
61
63
65
67
69
17
37
38
39
19
33
70
14
46
47
18
48
52
53
55
57
4
8
41
42
37
38
SHLD
8E
9E
5P
15
107
105
63
64
45
46
43A
11
11
11
25
119
119
119
11
11
11
11
11
REC 4D
45
CAT RELAY
CAT RELAY
EJB
EJB
63
86
87
7P
A B C
36J
C
120 ^
119
107
30
63 DIGITAL SENSOR RETURN 63
25
85
248 $ F RISING

46
36F
CS OPTION
E-STOP
107 COOLANT LEVEL 8V
2
J1939 DATA LINK LOW
25
CAT DATA LINK HIGH
CAT DATA LINK LOW
AIR INLET TEMPERATURE RETURN
36D 1
PRIMER
REMOTE CON. E-STOP

AIR INLET TEMPERATURE 5V
SEE SHT 2 C-5

36D
119

ON TOWER OPTION
R14A
36H
SET TO 5 SECONDS
36C
E-STOP
(P.P.BOX)
2
8
11
11
11
11
11
1
A
36C
36G
NCS OPTION
E-STOP
2
HYDRAULIC TANK
37 38 SHLD
LOW LEVEL
11
(18) (15)
1
FROM SHT 2
E-STOP
A2
TIME DELAY
15
5P
63
64
7P
JUMPER
(LHL)
36B
F
B
1
C
20 Amps
FP1 FUSE
A1
Y1
B
36F
EJB
40 Amps
HTD
SHLD
FP1 FUSE
9 PIN CAT
DATA LINK
CONNECTOR
43
8E
9E
38
37
7
36A
A
41
REC 10C 42
THROTTLE
CONTROLLER
2658316889
LEVELSWITCH
IN CONSOLE
A
HYD. TANK
REC CB13 REC 10A

REC 10H
E-STOP
2
REC CB5 REC 9A
1
COOLANT LEVEL
SENSOR
2657807638
REC R1
20 Amps
36
9 PIN J1939
SHLD
CB1LOAD
DATA LINK
CONNECTOR
20 Amps
5 Amps
37
38
7
5
IN CAB
REC CB15
7
20 Amps
LINE
7
7
7
1 24V 7
REC
1
CAT C15/C18 TIER 4F A
E
D
WARNING
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
SEE SHEET 1 FOR NOTES. AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1 REMOVE ALL BURRS AND SHARP POSITION
13OF 17
18 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
C27 TIER4
HC MITIGATION ( TIER4F ONLY )

FUEL PRIMER SWITCH IN CAB
C15 AND C18 UNDER 755 HP
HIGH SPEED REGEN ENABLE

AIR INLET TEMPERATURE
ECM UNSWITCHED POWER

D
FUEL PRIMER PUMP

J1939 DATA LINK
CAT DATA LINK
ETHER START
ECM GROUND
5 (GROUND)
5
5
5
ES
PM
5
5
3
5
70 PIN CONNECTOR
42
34
50
12
48
52
53
55
49
61
63
65
69
14
17
44
66
18
46
47
70
8
3
SHLD
8E
9E
38
37
11
11
11
11
107
105
113
25
63
64
15
5P
36J
EJB
248 $ F RISING
25
PRIMER
A B C
120 ^
EJB
113
119
C
EJB
107
113 DIGITAL SENSOR RETURN

ON TOWER OPTION
7P
107 COOLANT LEVEL 8V
36H
J1939 DATA LINK LOW
CAT DATA LINK HIGH
C27 AND C18 OVER 755 HP

E-STOP
CAT DATA LINK LOW
2
AIR INLET TEMPERATURE RETURN
25
AIR INLET TEMPERATURE 5V
PRIMER
36G

SET TO 5 SECONDS
HYDRAULIC TANK
11
11
11
11
(P.P.BOX)
LOW LEVEL
119
36F (18) (15)
E-STOP
A
NCS OPTION
E-STOP
2
7
37 38 SHLD
FROM SHT 1
CS OPTION
15
7P
5P
63
64
E-STOP
1
2
JUMPER
36B
A2
F
B
C
1
TIME DELAY
1
(LHL)
J1939 DATA LINK LOW
REMOTE CON. E-STOP

36D
EJB
SEE SHT 2 C-5
36D
Y1
A1
7
11
11
R14A
CONTROLLER
2658316889
A
36A
THROTTL
HTD
IN CONSOLE
36C
8
E-STOP
2
REC CB8 REC 10E
REC CB10 REC 10G
LEVELSWITCH
HYD. TANK
1
36C
COOLANT LEVEL
SENSOR
2657807638
36
9 PIN J1939
SHLD
SHLD
CB1LOAD
DATA LINK
CONNECTOR
9 PIN CAT
DATA LINK
CONNECTOR
5 Amps
15 Amps
15 Amps
37
38
8E
9E
38
37
5
5
IN CAB
LINE
6 24V
REC
7
7
7
7
D
WARNING
CAT C15, C18 & C27 TIER4 A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP .03 .005
ANGULARITY
DATE 05/26/2010 ELECTRICAL SCHEMATIC
SEE SHEET 1 FOR NOTES. PROCEDURE CWP/AWS-02 SM/FC-01. ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET
ANGLES 0 30'
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
SIZE D REF. NO.2658316865 DWG.
NO. 2658369444 CR
SCALE
NONE NO. 2658369444 SH
14OF 17
19 8 7 6 5 4 3 2
8 7 6 5 4 3 2 1
WIRE No. AWG COLOR NAME COMMENTS REV ECO/CN CHANGE APPRV
ZONE REVISIONS DATE
NO NO BY BY
1 8 WHITE POSITIVE BATTERY FEED FROM STARTER 1 SEE SHEET-1 FOR
WIRE No. AWG COLOR NAME COMMENTS
2 8 WHITE POWER TO LIGHTS AND ACCESSORIES REVISIONS
27 J1708 DATA LINK LOW CUMMINS QSX 15 TIER 3
2A 8 WHITE ALTERNATOR TO STARTER
28 WHITE STANDARD NIGHT LIGHT PACKAGE
2C 8 WHITE POWER TO STARTER SOLENOID(S)
28C WHITE INDICATOR LAMPS TEST SWITCH OPTION
3 16 WHITE ETHER START CUMMINS QSX 15 TIER 3
29 WHITE TRAM LIGHTS
3 16 WHITE ETHER START ECM PIN C TO SOLENOID VALVE CUMMINS QSK 19 TIER 2
30 WHITE ETHER BUTTON TO JUCTION BOX WIRE 3 CUMMINS
3 16 WHITE ETHER START ECM PIN 10 TO SOLENOID VALVE CAT C15 C18 TIER 3 CAT C27 TIER 2
31-32 NOT CURRENTLY USED
3 16 WHITE ETHER START CUMMINS QSX15 TIER 4 FINAL
33 14 WHITE ROD SUPPORT EXTEND CONTROL BOTTOM PIN TO R10 PIN 4 OPTION
3 16 WHITE ETHER START ECM PIN 11 TO SOLENOID VALVE CAT C15 C18 TIER 4 FINAL
3 16 WHITE ETHER START ECM PIN 12 TO SOLENOID VALVE C27 TIER4
33A 14 WHITE ROD SUPPORT EXTEND R10 PIN 2 TO 9 SPOOL SEC. 2 C2 OPTION D
34 14 WHITE ROD SUPPORT RETRACT CONTROL TOP PIN TO 9 SPOOL SEC. 2 C1 OPTION
4 10 RED REC PIN 9G TO NCS STARTER SOLENOID CUMMINS QSX15 TIER 4 FINAL
35 8 WHITE POWER TO STARTER 1 SOLENOID 2
4 10 RED REC PIN 9G TO NCS STARTER SOLENOID CAT C15 C18 TIER 4 FINAL
35A 8 WHITE POWER TO STARTER 2 SOLENOID 2A OPTION CUMMINS QSX 15 TIER 3
4B 10 RED REC PIN 9B TO CS STARTER SOLENOID CUMMINS QSX15 TIER 4 FINAL
35A 8 WHITE POWER TO STARTER 2 SOLENOID 2A OPTION CUMMINS QSK 19 TIER 2
4B 10 RED REC PIN 9B TO CS STARTER SOLENOID CAT C15 C18 TIER 4 FINAL
35A 8 WHITE POWER TO STARTER 2 SOLENOID 2A OPTION CAT C15 C18 TIER 3 CAT C27 TIER 2
5 8 10 14 BLACK GROUND POWER SUPPLY GROUND BATTERY RETURN
35A 8 WHITE POWER TO STARTER 2 SOLENOID 2A CUMMINS QSX 15 TIER 4 FINAL
5P 16 BLUE THROTTLE RETURN ECM PIN 49 TO THROTTLE PIN B CUMMINS QSX 15 TIER 3
35A 8 WHITE POWER TO STARTER 2 SOLENOID 2A CAT C15 C18 TIER 4 FINAL
5P 16 BLUE THROTTLE RETURN ECM PIN 22 TO THROTTLE PIN B CUMMINS QSK 19 TIER 2
36A 16 WHITE ENGINE SHUTDOWN E-STOP IN CONSOLE TO E-STOP OF REMOTE PROPEL
5P 16 BLUE THROTTLE RETURN THROTTLE PIN B TO GROUND CAT C15 C18 TIER 3 CAT C27 TIER 2
36B 16 WHITE ENGINE SHUTDOWN NCS E-STOP TO CS E-STOP
5P 16 BLUE THROTTLE RETURN 1 ECM PIN 33 TO THROTTLE PIN CUMMINS QSX15 TIER 4 FINAL
36C 16 WHITE ENGINE SHUTDOWN CS E-STOP TO ECM SHUTDOWN
5P 16 BLUE THROTTLE RETURN ECM PIN 5 TO THROTTLE PIN B CAT C15 C18 TIER 4 FINAL
36D NOT CURRENTLY USED
5P 16 BLUE THROTTLE RETURN ECM PINS 18 & 47 TO THROTTLE PIN B C27 TIER4
36F 16 WHITE ENGINE SHUTDOWN COMPRESSOR SHUTDOWN TO HYDRAULIC LOW LEVEL
6 10 WHITE POWER FROM KEY SWITCH TO CIRCUIT BREAKERS AND EARS
36G 16 WHITE ENGINE SHUTDOWN HYDRAULIC LOW LEVEL TO NCS E-STOP
7 12 WHITE POWER FROM CIRCUIT BREAKER 5 R7 PIN 8 ETC.
36J 16 WHITE ENGINE SHUTDOWN CS E-STOP TO ECM SHUTDOWN
7A 16 WHITE FROM R7 PIN 6 TO START BUTTON CUMMINS QSX 15 TIER 3
37 18 WHITE J1939 DATA LINK HIGH
7A 16 WHITE FROM R7 PIN 6 TO START BUTTON CUMMINS QSK 19 TIER 2
38 18 BLACK J1939 DATA LINK LOW
7A 16 WHITE FROM R7 PIN 6 TO START BUTTON CAT C15 C18 TIER 3 CAT C27 TIER 2
SHLD 18 BARE J1939 DATA LINK SHIELD
7A 16 WHITE FROM R7 PIN 6 TO START BUTTON CAT C15 C18 TIER 4 FINAL 39 24V OUTLET INLINE FUSE TO OUTLET OPTION
7A 16 WHITE FROM R1 PIN 6 TO START BUTTON CUMMINS QSX15 TIER 4 FINAL 40 14 WHITE WIND SHIELD WIPER CB2 TO SWITCH
7B 16 WHITE FROM R7 PIN 6 TO R1 PIN 8 CUMMINS QSX15 TIER 4 FINAL 41 RED PETU POWER CAT C15/C18 TIER 4 FINAL
7P 16 GREEN THROTTLE CONTROL 5V FROM ECM PIN 48 TO THROTTLE PIN C CUMMINS QSX 15 TIER 3 42 RED PETU POWER CAT C15/C18 TIER 4 FINAL
7P 16 GREEN THROTTLE CONTROL 5V FROM ECM PIN 20 TO THROTTLE PIN C CUMMINS QSK 19 TIER 2 43 RED FUEL PRIMER PUMP REC 9A TO CAT RELAY PIN 30 CAT C15/C18 TIER 4 FINAL
C
7P 16 GREEN THROTTLE CONTROL POWER FROM CIRCUIT 7 TO THROTTLE PIN C CAT C15 C18 TIER 3 CAT C27 TIER 2 43A FUEL PRIMER PUMP CAT RELAY PIN 87 TO ECM PIN 39 CAT C15/C18 TIER 4 FINAL
7P 16 GREEN THROTTLE CONTROL 5V FROM ECM PIN 9 TO THROTTLE PIN C CUMMINS QSX15 TIER 4 FINAL 44 14 WHITE ENGINE SHUT DOWN ECM PIN 44 TO RELAY R1 PIN 4 CAT C15 C18 TIER 3 CAT C27 TIER 2
7P 16 GREEN THROTTLE CONTROL FROM ECM PIN 4 TO THROTTLE PIN C CAT C15 C18 TIER 4 FINAL 45 18 WHITE PRIMER PUMP ECM CONTROL, 12 PIN CON. PIN 1 TO CAT RELAY PIN 86 CAT C15/C18 TIER 4 FINAL
7P 16 GREEN THROTTLE CONTROL FROM EJB TO THROTTLE PIN C C27 TIER4 46 18 WHITE PRIMER PUMP ECM CONTROL, 12 PIN CON. PIN 2 TO CAT RELAY PIN 85 CAT C15/C18 TIER 4 FINAL
8 14 WHITE ENGINE START BUTTON STARTER RELAY(S) 47-49 NOT CURRENTLY USED
8E 18 WHITE CAT DATA LINK HIGH ECM PIN 8 TO DATA LINK CONNECTOR D CAT C15 C18 TIER 3 CAT C27 TIER 2 50 18 WHITE D.C. SIDE MAIN PUMP CW COIL POWER FROM R4 PIN 8
8E 18 WHITE CAT DATA LINK HIGH ECM PIN 8 TO DATA LINK CONNECTOR D CAT C15 C18 TIER 4 FINAL 51 18 WHITE D.C. SIDE MAIN PUMP CCW COIL POWER FROM R4 PIN 4
8E 18 WHITE CAT DATA LINK HIGH ECM PIN 8 TO DATA LINK CONNECTOR D C27 TIER4 52 NOT CURRENTLY USED
53 14 WHITE MAIN PUMP R4 PIN 2 TO CONTROLLER PIN B NO REMOTE PROPEL OPTION
9 16 WHITE FUEL GAUGE TO FUEL LEVEL SENDER
53 MAIN PUMP R13 PIN 3 TO CONTROLLER PIN A REMOTE PROPEL OPTION
9E 18 WHITE CAT DATA LINK LOW ECM PIN 9 TO DATA LINK CONNECTOR E CAT C15 C18 TIER 3 CAT C27 TIER 2
53A 14 WHITE REMOTE PROPEL OPTION R4 PIN 2 TO R13 PIN 4
9E 18 WHITE CAT DATA LINK LOW ECM PIN 9 TO DATA LINK CONNECTOR E CAT C15 C18 TIER 4 FINAL
54 14 WHITE MAIN PUMP R4 PIN 6 TO CONTROLLER PIN A NO REMOTE PROPEL OPTION
9E 18 WHITE CAT DATA LINK LOW ECM PIN 9 TO DATA LINK CONNECTOR E C27 TIER4
54 MAIN PUMP R13 PIN 7 TO CONTROLLER PIN A REMOTE PROPEL OPTION
10 NOT CURRENTLY USED
54A REMOTE PROPEL OPTION R4 PIN 6 TO R13 PIN 8 REMOTE PROPEL OPTION
10E PANEL GROUND 55 NOT CURRENTLY USED
11 16 WHITE ECM 24VDC 15 AMP FUSE TO ECM PINS 7 8 17 18 & 28 CUMMINS QSX 15 TIER 3 56 14 WHITE MAIN PUMP R13 PIN 6 TO REMOTE CONTROLLER PIN A REMOTE PROPEL OPTION
11 16 WHITE ECM 24VDC 15 AMP FUSE TO ECM PINS A & F CUMMINS QSK 19 TIER 2 57 14 WHITE MAIN PUMP R13 PIN 2 TO REMOTE CONTROLLER PIN B REMOTE PROPEL OPTION
11 16 WHITE ECM 24VDC 15 AMP FUSE TO ECM PINS 48 52 & 53 CAT C15 C18 TIER 3 CAT C27 TIER 2 58 14 WHITE ROTATION CONTROLLER PIN A TO R4 PIN 7
11 16 WHITE ECM 24VDC 30 AMP FUSE TO ECM PINS 1 25 26 27 & 28 CUMMINS QSX15 TIER 4 FINAL 59 14 WHITE ROTATION CONTROLLER PIN B TO R4 PIN 3
11 16 WHITE ECM 24VDC 20 AMP FUSE TO ECM PINS 6 19 33 48 52 53 55 & 57 CAT C15 C18 TIER 4 FINAL 60 14 WHITE PROPEL I'LOCK R11 PIN 6 & ROD SUPPORT I'LOCK R2 PIN 6 TO R3 PIN 7
11 16 WHITE UNSWITCHED BATTERY 24V REC CB10 TO ECM PINS 48 52 C27 TIER4 61 14 WHITE PULLDOWN CONTROLLER PIN A TO R11 PIN 8 & R2 PIN 8
11 16 WHITE UNSWITCHED BATTERY 24V REC CB8 TO ECM PINS 53 55 C27 TIER4 62 14 WHITE UPPER TOWER DECEL LIMIT SWITCH 5 AND TRAM INTERLOCK OPTION
12 COMPRESSOR DISCHARGE TEMPERATURE GAUGE TO SENDER 63 DIGITAL SENSOR RETURN ECM PIN 3 TO SENSOR PIN B CAT C15 C18 TIER 4 FINAL B
13 16 WHITE THROTTLE CONTROL SIGNAL ECM PIN 47 TO THROTTLE PIN A CUMMINS QSX 15 TIER 3 63 AIR INLET TEMPERATURE RETURN ECM PIN 3 TO SENSOR PIN 1 C27 TIER4
13 16 WHITE THROTTLE CONTROL SIGNAL ECM PIN 21 TO THROTTLE PIN A CUMMINS QSK 19 TIER 2 64 AIR INLET TEMPERATURE 5V ECU PIN 17 TO SENSOR PIN 1 CAT C15 C18 TIER 4 FINAL
13 16 WHITE THROTTLE POSITION 1 ECM PIN 10 TO THROTTLE PIN A CUMMINS QSX15 TIER 4 FINAL 64 AIR INLET TEMPERATURE 5V ECM PIN 17 TO SENSOR PIN 2 C27 TIER4
14 16 WHITE THROTTLE POSITION 2 ECM PIN 64 TO THROTLE PIN E CUMMINS QSX15 TIER 4 FINAL 65 14 WHITE NON-DRILL END JACK RETRACT INDICATOR LS3 TO LIGHT
65A 14 WHITE NON-DRILL END JACKS RETRACT INDICATOR LS3A TO LS3
15 16 WHITE THROTTLE CONTROL SIGNAL ECM PIN 66 TO THROTTLE PIN F CAT C15 C18 TIER 3 CAT C27 TIER 2
66 14 WHITE CAB SIDE JACK RETRACT INDICATOR
15 16 WHITE THROTTLE RETURN 2 ECM PIN 61 TO THROTTLE PIN F CUMMINS QSX 15 TIER 4 FINAL
67 14 WHITE D C SIDE JACK RETRACT INDICATOR
15 16 WHITE THROTTLE CONTROL SIGNAL ECM PIN 66 TO THROTTLE PIN F CAT C15 C18 TIER 4 FINAL
68 14 WHITE WATER DUMP VALVES SWITCH TO VALVE COILS OPTION
15 16 WHITE THROTTLE CONTROL SIGNAL ECM PIN 66 TO THROTTLE PIN F C27 TIER4
69 14 WHITE PARKING BRAKE SWITCH TO VALVE COIL
16 16 WHITE WATER DUMP VALVES CB9 TO SWITCH OPTION ALL TIER 2 AND TIER 3
69A 14 WHITE PARKING BRAKE SWITCH TO DIODE D14 OPTION
16 16 WHITE WATER DUMP VALVES CB11 TO SWITCH OPTION ALL TIER 4 FINAL 69B 14 WHITE PARKING BRAKE DIODE D14 TO DIODE D2 AND INDICATOR OPTION
17 16 WHITE START INTERLOCK R5 PIN 6 TO R6 PIN 8 70A WHITE DRILL POSITION NC TO DRILL/PROPEL/JACK INTERLOCK
18 12 WHITE CAB HEATER/PRESSURIZER CB4 TO ROTORY SWITCH 70B WHITE DRILL/PROPEL/JACK INTERLOCKS TO PROPEL CONTROL POWER
18A 12 WHITE AIR CONDITIONER CB4 TO A/C ON/OFF SWITCH AND CAB BLOWER MOTOR OPTION 70C WHITE DRILL/PROPEL/JACK INTERLOCKS RELAY R8 PIN 6 TO RELAY R9 PIN 2
19 14 WHITE START INTERLOCK R6 PIN 6 TO DRILL POSITION BUTTON 71 14 WHITE REMOTE PROPEL 70B CONNECTOR PIN J & PIN K TO REMOTE POWER REMOTE PROPEL OPTION
20 14 WHITE START INTERLOCK DRILL POSITION BUTTON TO R7 PIN 0 72 14 WHITE POWER TO BRAKE RELEASE SOLONOID COIL REMOTE PROPEL OPTION
21 14 WHITE AC COMPRESSOR CLUTCH A/C SWITCH TO THERMOSTAT SWITCH 73 14 WHITE MAIN PUMP R3 PIN 6 TO CONTROLLER PIN A NO REMOTE PROPEL OPTION
21A 14 BLACK AC COMPRESSOR CLUTCH THERMOSTAT SWITCH TO LOW PRESS. SWITCH 73 14 WHITE MAIN PUMP R12 PIN 7 TO CONTROLLER PIN A REMOTE PROPEL OPTION
21B AC COMPRESSOR CLUTCH LOW PRESS. SWITCH TO HIGH PRESS. SWITCH 74 14 WHITE MAIN PUMP R3 PIN 2 TO CONTROLLER PIN B NO REMOTE PROPEL OPTION
21C AC COMPRESSOR CLUTCH HIGH PRESS. SWITCH TO A/C CLUTCH
22 8 RED MICROWAVE CB8 TO MICROWAVE
23 14 WHITE TOWER UNPINNED INDICATOR D
WARNING
A
24 NOT CURRENTLY USED CWP/AWS-02/5SA-08
25 14 RED FUEL PRIMER PUMP CAT C15 C18 TIER 3 CAT C27 TIER 2 COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
A CWP/AWS-02GM-42
LETTER EPIROC DRILLING SOLUTIONS
25 FUEL PRIMER PUMP C27 TIER4 DESIGNATOR PROCEDURE NO
SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE.
DIM (IN) TOL (IN)
DIM (IN)
TOL (IN) FLATNESS CHECKED BY J. DENK
26 J1708 DATA LINK HIGH CUMMINS QSX 15 TIER 3 PART AS INDICATED BY THE "LETTER DESIGNATOR" IN ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES
24
.06
UNDER 24 .01 .005
ROUNDNESS
THE TAIL OF THE WELD SYMBOL. (CIRCULARITY) ENG. APPVL. Q. DUNN
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
15 OF 17
20 8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
74 14 WHITE MAIN PUMP R12 PIN 3 TO CONTROLLER PIN B REMOTE PROPEL OPTION
75 14 WHITE MAIN PUMP R12 PIN 6 TO REMOTE CONTROLLER CONNECTOR PIN G REMOTE PROPEL OPTION
76 14 WHITE MAIN PUMP R12 PIN 2 TO REMOTE CONTROLLER CONNECTOR PIN H REMOTE PROPEL OPTION WIRE No. AWG COLOR NAME COMMENTS
77 14 WHITE REMOTE PROPEL OPTION R3 PIN 6 TO R12 PIN 8 REMOTE PROPEL OPTION 130 NOT CURRENTLY USED
78 14 WHITE PULLDOWN FORCE LIMIT POTENTIOMETER TO LIMIT SWITCH LS4 131 WATER INJECTION PULSE N.C. TO PULSE TIMER AND 6 SPOOL SEC. 6 C1
78A 14 WHITE PULLDOWN FORCE LIMIT RISISTOR TO POTENTIOMETER 132 NOT CURRENTLY USED
79 14 WHITE PULLDOWN FORCE LIMIT FROM R10 PIN 7 AND 500 ^ POT. TO R3 PIN 3 133 WATER INJECTION PULSE N.C. TO WATER INJECTION CONTROL +
79A 14 WHITE PULLDOWN CONTROLLER PIN B TO R10 PIN 8 & TO 50 ^ RESISTOR 134 WATER INJECTION CONTROL PIN A TO 6 SPOOL SEC. 6 C2
79B 14 WHITE REMOTE PROPEL R3 PIN 2 TO R12 PIN 4 REMOTE PROPEL OPTION 135 REC PIN 4C TO ECM PIN 3 D
80 12 14 WHITE POWER DISTRIBUTION FOR OEM CONTROLLERS 136 SUPPLY MODULE TEMP DRIVER ECM PIN 6 TO DEF SUPPLY MODULE PIN 10 CUMMINS QSX15 TIER 4 FINAL
81 14 WHITE MAIN PUMP CONTROLLER PIN D TO HOLDBACK SOLENOID VALVE 137 KEY SWITCH POWER TO R21 PIN 86 CUMMINS QSX15 TIER 4 FINAL
82 12 14 WHITE POWER FOR DRILL MODE FUNCTIONS 137A KEY SWITCH POWER FROM R21 PIN 85 TO ECM PIN 7 CUMMINS QSX15 TIER 4 FINAL
82A 14 WHITE ROD SUPPORT RETRACT LIMIT SWITCH LS6 TO RELAY R2 PIN 0 OPTION 138 WATER IN FUEL SENSOR ECM PIN 13 TO SENSOR PIN 1 CUMMINS QSX15 TIER 4 FINAL
83 14 WHITE CAB SIDE JACK CONTROL PIN B TO 6 SPOOL SEC. 5 C2 139-140 NOT CURRENTLY USED
84 14 WHITE CAB SIDE JACK CONTROL PIN A TO 6 SPOOL SEC. 5 C1 141 PRESSURE SENSOR ECM PIN 16 TO DEF SUPPLY MODULE PIN 3 CUMMINS QSX15 TIER 4 FINAL
85 14 WHITE NON DRILL END JACK CONTROL PIN B TO 6 SPOOL SEC. 4 C2 142 REC PIN 4H TO ECM PIN 38 CUMMINS QSX15 TIER 4 FINAL
86 14 WHITE NON DRILL END JACK CONTROL PIN A TO 6 SPOOL SEC. 4 C1 143 REC PIN 4G TO ECM PIN 39 CUMMINS QSX15 TIER 4 FINAL
87 14 WHITE D.C. SIDE JACK CONTROL PIN B TO 6 SPOOL SEC. 3 C2 144 REC PIN 4B TO ECM PIN 40 CUMMINS QSX15 TIER 4 FINAL
88 14 WHITE D.C. SIDE JACK CONTROL PIN A TO 6 SPOOL SEC. 3 C1 145 DEF DOSER INJECTOR ECM PIN 53 TO DEF DOSER PIN 2 CUMMINS QSX15 TIER 4 FINAL
89 14 WHITE D.C. SIDE MAIN PUMP CONTROLLER PIN N TO R6 PIN 0 & 3 SPEED HEAD 146 PUMP MOTOR RETURN ECM PIN 54 TO DEF SUPPLY MODULE PIN 8 CUMMINS QSX15 TIER 4 FINAL
90 14 WHITE CAB SIDE MAIN PUMP CONTROLLER PIN N TO R5 PIN 0 147 ECM PIN 57 TO DEF HEATER VALVE PIN 2 & DEF SUPPLY MOD. PIN 12 CUMMINS QSX15 TIER 4 FINAL
91 14 WHITE TOWER RAISE CONTROL PIN B TO 6 SPOOL SEC. 2 C2 148 WATER IN FUEL SENSOR ECM PIN 62 TO SENSOR PIN 2 CUMMINS QSX15 TIER 4 FINAL
92 14 WHITE TOWER LOWER CONTROL PIN A TO 6 SPOOL SEC. 2 C1 149 DEF DOSER INJECTOR ECM PIN 77 TO DEF DOSER PIN 1 CUMMINS QSX15 TIER 4 FINAL
93 14 WHITE TOWER PINNING CONTROLER BOTTOM PIN TO 9 SPOOL SEC. 4 C2 150 DUST FLAP FORWARD SWITCH TO 9 SPOOL SEC. 7 C2
94 14 WHITE TOWER PINNING CONTROLER TOP PIN TO 9 SPOOL SEC. 4 C1 151 DUST FLAP BACK SWITCH TO 9 SPOOL SEC. 7 C1
95 18 WHITE CAB SIDE MAIN PUMP CW COIL POWER FROM R3 PIN 8 152 PUMP MOTOR SUPPLY ECM PIN 79 TO DEF SUPPLY MODULE PIN 9 CUMMINS QSX15 TIER 4 FINAL
96 18 WHITE CAB SIDE MAIN PUMP CCW COIL POWER FROM R3 PIN 4 153 DEF REVERTING VALVE ECM PIN 81 TO DEF SUPPLY MODULE PIN 11 CUMMINS QSX15 TIER 4 FINAL
97 NOT CURRENTLY USED 154 DEF TANK CONTROL VALVE ECM PIN 82 TO HEATER VALVE PIN 1 CUMMINS QSX15 TIER 4 FINAL
98 14 WHITE PULLDOWN FORCE LIMIT LIMIT SWITCH LS4 TO COIL PA PIN 0 155 DEF HEATER PIN 2 TO ECM PINS 84 & 85 CUMMINS QSX15 TIER 4 FINAL
99 NOT CURRENTLY USED 156 NOT CURRENTLY USED C
100 14 WHITE PULLDOWN CONTROLLER 50 ^ RESISTER TO 0-500 ^ POT. 157 RELAY SUPPLY RELAY R21 PIN 87 TO DEF SUPPLY MODULE PIN 5 CUMMINS QSX15 TIER 4 FINAL
101-104 NOT CURRENTLY USED 158-163 NOT CURRENTLY USED
105 COOLANT LEVEL LOW SIGNAL ECM PIN T TO SENSOR PIN A CUMMINS QSX 15 TIER 3 164 CIRCUIT BREAKER 6 TO DRILL LIGHT SWITCH
105 COOLANT LEVEL SIGNAL ECM PIN W TO SENSOR PIN C CUMMINS QSK 19 TIER 2 165 12 DRILL LIGHT SWITCH TO LIGHTS
105 COOLANT LEVEL SIGNAL ECM PIN 49 TO SENSOR C CAT C15 C18 TIER 3 CAT C27 TIER 2 166-169 NOT CURRENTLY USED
105 COOLANT LEVEL SIGNAL ECM PIN 35 TO SENSOR B CUMMINS QSX 15 TIER 4 FINAL 170 HOIST CONTROL PIN B TO 6 SPOOL SECT. 1 C1
105 COOLANT LEVEL SIGNAL ECM PIN 49 TO SENSOR C CAT C15 C18 TIER 4 FINAL 171 HOIST CONTROL PIN A TO 6 SPOOL SECT. 1 C2
105 COOLANT LEVEL SIGNAL ECM PIN 49 TO SENSOR C C27 TIER4 172-179 NOT CURRENTLY USED
106 14 WHITE PULLDOWN FORCE LIMIT CONTROL PIN A TO LIMIT SWITCH LS4 180 10 WHITE FUEL/WATER FILTER HEATER REC PIN 9D TO STARTER RELAY R20 PIN 30 CUMMINS QSX15 TIER 4 FINAL
107 COOLANT LEVEL 5V ECM PIN U TO SENSOR C CUMMINS QSX 15 TIER 3 180A 12 RED FUEL/WATER FILTER HEATER STARTER RELAY R20 PIN 87 TO HEATER CUMMINS QSX15 TIER 4 FINAL
107 COOLANT LEVEL 5V ECM PIN 8 TO SENSOR A CUMMINS QSK 19 TIER 2 181 JACK RETRACT/PROPEL INTERLOCK LS1 TO LS2
107 COOLANT LEVEL 8V ECM PIN 4 TO SENSOR A CAT C15 C18 TIER 3 CAT C27 TIER 2 182 JACK RETRACT/PROPEL INTERLOCK LS2 TO LS3A
107 SENSOR SUPPLY ECM PIN 8 TO SENSR A CUMMINS QSX 15 TIER 4 FINAL 182A 14 WHITE JACK RETRACT/PROPEL INTERLOCK LS3A TO LS3
107 COOLANT LEVEL 8V ECM PIN 4 TO SENSOR PIN A CAT C15 C18 TIER 4 FINAL 183 JACK RETRACT/PROPEL INTERLOCK LS3 TO R8 PIN 0
107 COOLANT LEVEL 8V ECM PIN 4 TO SENSOR PIN A C27 TIER4 184-189 NOT CURRENTLY USED
108 14 WHITE DUST HOOD TELESCOPING DOWN SWITCH TO 9 SPOOL SEC. 5 C2 OPTION 190 PURPLE LINCOLN LUBE CONTROL SENSOR PIN 9 TO PRESSURE SWITCH OPTION
109 14 WHITE DUST HOOD TELESCOPING UP SWITCH TO 9 SPOOL SEC. 5 C1 OPTION 191 RED LINCOLN LUBE CONTROL SENSOR PIN 8 TO PRESSURE SWITCH OPTION
110 COOLANT LEVEL HIGH SIGNAL ECM PIN S TO SENSOR D CUMMINS QSX15 TIER 3 192 LINCOLN LUBE CONTROL SENSOR PIN 3 TO LOW LEVEL SWITCH OPTION
111 NOT CURRENTLY USED 193 BLACK LINCOLN LUBE CONTROL SENSOR PIN 2 TO LOW LEVEL SWITCH OPTION
112 14 WHITE HOLD BACK CONTROL PIN A TO COIL PA PIN 0 OPTION 194 RED LINCOLN LUBE CONTROL PUMP PIN 9 TO R17 PIN 0 OPTION
113 COOLANT LEVEL RETURN ECM PIN V TO SENSOR B CUMMINS QSX 15 TIER 3 195 RED LINCOLN LUBE CONTROL PUMP PIN 8 TO R17 PIN 1 OPTION
113 COOLANT LEVEL RETURN ECM PIN X TO SENSOR B CUMMINS QSK 19 TIER 2 196 LINCOLN LUBE CONTROL PUMP RELAY R17 PIN 8 TO PUMP SOLENOID OPTION B
113 COOLANT LEVEL RETURN ECM PIN 5 TO SENSOR B CAT C15 C18 TIER 3 CAT C27 TIER 2 197 WHITE PROHEAT
113 OEM SENSOR RETURN ECM PIN 32 TO SENSOR C CUMMINS QSX 15 TIER 4 FINAL 198 RED PROHEAT
113 DIGITAL SENSOR RETURN ECM PIN 5 TO EJB AND SENSOR B C27 TIER4 199 GREEN PROHEAT
114 14 WHITE DHD TIMER PIN2 (TIMER) 24V OUT TO DHD PUMP SOLENOID VALVE OPTION 200 BLACK PROHEAT
114A 14 WHITE DHD PUMP INLINE FUSE TO SWITCH OPTION- FOR ALL TIER 2/3 201 WHITE 12V TO CONSOLE
114A 14 WHITE DHD PUMP CB12 TO SWITCH OPTION- FOR TIER 4 FINAL 202 LINCOLN LUBE PNEUMATIC THREAD LUBRICATOR OPTION
114B 14 WHITE DHD PUMP SWITCH TO DHD TIMER PIN1 24V IN OPTION 203 ANTI-RUMBLE VACCUME SWITCH TO SOLENOID VALVE
114C 14 WHITE DHD TIMER PIN3 (CONSTANT) 24V OUT TO DHD PRESSURE SWITCH OPTION 204 10 RACOR FUEL HEATER CB10 TO HEATER THERMOSTAT OPTION
115 14 WHITE DHD PRESSURE SWITCH TO INDICATOR ON CONSOLE OPTION 205 ROTARY HEAD TACHOMETER MAG PICKUP TO TACH OPTION
115A 14 WHITE DHD TIMER PIN2 (TIMER) 24V OUT TO RETURN TO TANK SOLENOID OPTION 206 ROTARY HEAD TACHOMETER MAG PICKUP TO TACH OPTION
116 14 WHITE HIGH PRESSURE THROTTLE PIN A TO 9 SPOOL SEC. 4 C1 OPTION 207-208 NOT CURRENTLY USED
117 14 WHITE HIGH PRESSURE THROTTLE PIN B TO 9 SPOOL SEC. 4 C2 OPTION 209 HORN SWITCH TO HORNS
118 14 WHITE TORQUE LIMIT CONTROL PIN A TO COIL PA PIN 0 OPTION 210A ELCTRIC THREAD LUBRICATOR RESET SWITCH TO PRESS. SWITCH OPTION
119 16 WHITE PRIMER SWITCH TO MAIN JUNCTION BOX OPTION 210B ELCTRIC THREAD LUBRICATOR PRESS. SWITCH TO INTERVAL TIMER PIN 15 & A1 OPTION
120 14 WHITE ROD INDEXING CCW CONTROL PIN A TO 9 SPOOL SEC. 8 C1 211 ELCTRIC THREAD LUBRICATOR RELAY R18 PIN 8 TO MOTOR OPTION
121 14 WHITE ROD INDEXING CW CONTROL PIN B TO 9 SPOOL SEC. 8 C2 212 SPARE IN HARNESS FROM MAIN JUNCTION BOX TO CAB
122 14 WHITE CHAIN WRENCH RETRACT CONTROL PIN A TO 9 SPOOL SEC. 3 C1
122W 14 WHITE CHAIN WRENCH CONTROL PIN A TO 9 SPOOL SEC. 3 C1 OPTION
123 14 WHITE CHAIN WRENCH EXTEND CONTROL PIN B TO 9 SPOOL SEC. 3 C2
124 14 WHITE VARIABLE FAN SPEED CONTROL PIN A TO PA PIN 0 OPTION
125 NOT CURRENTLY USED D
WARNING
A
126 14 WHITE BREAKOUT FORK CONTROL PIN B TO 9 SPOOL SEC. 9 C1 CWP/AWS-02/5SA-08
127 14 WHITE BREAKOUT FORK CONTROL PIN A TO 9 SPOOL SEC. 9 C2 COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
A CWP/AWS-02GM-42
LETTER
128 CAROUSEL SWING CONTROL PIN B TO 9 SPOOL SECT. 1 C2 DESIGNATOR
EPIROC DRILLING SOLUTIONS
PROCEDURE NO
DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY J. DENK
UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE 05/26/2010 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
129 CAROUSEL SWING CONTROL PIN A TO LIMIT SWITCH LS7 THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS
PART AS INDICATED BY THE "LETTER DESIGNATOR" IN
THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW-
24
.06
UNDER 24 .01 .005
ROUNDNESS
THE TAIL OF THE WELD SYMBOL. (CIRCULARITY) ENG. APPVL. Q. DUNN
129A CAROUSEL SWING LIMIT SWITCH LS7 TO 9 SPOOL SECT. 1 C1 OPTION TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
16 OF 17
21 8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY

213 3 SPEED ROTARY HEAD MEDIUM SPEED SET OPTION
213A 3 SPEED ROTARY HEAD HIGH SPEED RESET OPTION
214 3 SPEED ROTARY HEAD HIGH SPEED SET OPTION
215 3 SPEED ROTARY HEAD POWER OPTION D
215A 3 SPEED ROTARY HEAD HIGH SPEED OPTION
215B 3 SPEED ROTARY HEAD MEDIUM SPEED OPTION
216 3 SPEED ROTARY HEAD LOW SPEED OPTION
216A 3 SPEED ROTARY HEAD MEDIUM SPEED RESET OPTION
308 PULLDOWN FORCE LIMIT PROXIMITY SWITCH PS4 TO TELAY R15 PIN 0
309 CAROUSEL SWING PROXIMITY SWITCH PS7 TO RELAY R16 PIN 0
313 16 WHITE STARTER LOCKOUT RELAY R1 PIN 0 TO ECU PIN 76 CUMMINS QSX 15 TIER 4 FINAL
314 NOT CURRENTLY USED
315 16 WHITE STARTER LOCKOUT RELAY R1 PIN 1 TO ECU PIN 83 CUMMINS QSX 15 TIER 4 FINAL
B1 Feb-00 BLACK BATTERY TO CHASSIS GROUND
B2 BATTERY TO FUSE FOR ECM POWER
B3 NOT CURRENTLY USED
B4 BATTERY SUPPLY +24V TO STARTER 1
CAB1 14 WHITE WASHER MOTOR #1 PARK CAB BUILDER WIRE LABEL 1
CAB2 14 WHITE WIPER MOTOR #1 LOW - OFF - HIGH CAB BUILDER WIRE LABEL 2
CAB21 14 WHITE WIPER MOTOR #2 PARK CAB BUILDER WIRE LABEL 21
CAB23 14 WHITE WIPER MOTOR #2 LOW - OFF - HIGH CAB BUILDER WIRE LABEL 23 C
RESERVOIR 14 WHITE WASHER PUMP #1 CAB BUILDER WIRE LABEL
RESERVOIR 14 WHITE WASHER PUMP #2 CAB BUILDER WIRE LABEL
D
WARNING
A
CWP/AWS-02/5SA-08
A CWP/AWS-02GM-42
.06 ROUNDNESS
TITLE
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
FINISHED WEIGHT
NO. 2658369444 CR
17 OF 17
22 8 7 6 5 4 3 2 1
23 Epiroc operated under the trademark 'Atlas Copco' prior to January 1, 2018
8 7 6 5 4 3 2 1
240 VAC NO
ZONE
NO
REVISIONS DATE
BY BY
BLACK 2A REFER TO ARCHIVE DRAWINGS FOR

PREVIOUS REVISION HISTORY
L1 D 100 D 100A 009 SHT-1
USS19
02215
10/29/19 SPG RR
RED 14 AWG 14 AWG A3 UPDATED NOTE-2
L2 300 WATTS
WHITE
N OIL PAN HEATER
GREEN 2A OPEN AT
140 $ F (CAT ENGINE OPTION) BLACK 5A
GND D 101 L1 D 100 D 100A
14 AWG RED 14 AWG 14 AWG
L2
WHITE
450 WATTS D
2A N OIL PAN HEATER
D 102 GREEN
OPEN AT
140 $ F (120V)
14 AWG GND 903
(QSX15 ENGINE
300 WATTS 14 AWG
2A OPTION)
D 103 BATTERY HEATERS (OPTION)
14 AWG
20A
D 118 D 118A
15A
12 AWG 12 AWG
D 104 104A
14 AWG 104B 1 WATER TANK HEATER
2 1000 WATTS 3000 WATTS (OPTION)
105A D 119A
RECEIVER TANK D 119
3
105B HEATERS (OPTION) 20A 12 AWG 12 AWG
D 105 4
SET AT
60 $ F
15A 14 AWG
20A
D 120 D 120A C
12 AWG 12 AWG
OPTIONAL WATER TANK HEATER

D 121 D 121A 3000 WATTS (OPTION)
20A 20A 12 AWG 12 AWG SET AT
D 108 60 $ F
12 AWG
3500 WATTS
ENGINE BLOCK
HEATER (OPTION) 3A
D 109
12 AWG D 122
20A 12 AWG
20A
D 110
12 AWG FUEL TANK HEATERS WITH
THERMOSTAT 3000 WATTS OPTIONAL HEAT TRACE
D 111 CLOSE 40 $ F, OPEN 50 $ F (OPTION) WATER INJECTION (OPTION)
3A
20A 12 AWG D 123
900 RELAY 12 AWG
12 AWG
D 112B HVR1
HYD. TANK 20A JUNCTION BOX B
15A 12 AWG HYD. TANK
D 124
D 112 D 112A HEATER
12 AWG OPTIONAL COC/HOC
14 AWG 14 AWG 2000 WATTS
(OPTION) COOLER TOP & BOTTOM
D 113 TANK HEATERS
14 AWG D 125 3000 WATTS (OPTION)
15A SET AT
60 $ F
20A 12 AWG
901
12 AWG RELAY
D 114B DHD LUBE TANK
15A 12 AWG
HVR2
MAIN ELECTRICAL BOX
NOTE:
D 114 D 114A DHD LUBE TANK
12 AWG 12 AWG HEATER 1. THE LOW LEVEL SENSOR IS
2000 WATTS (OPTION) A MANUAL RESET DEVICE.
D 115 WARNING:
2. ALL RELAYS MOUNTED IN
15A 12 AWG SET AT
240 VOLT ELECTRICAL BOX.
60 $ F
ALWAYS TURN "OFF" ELECTRIC HEATERS
3. IF STONCO BOXES ARE USED GROUND
WARNING IN ENGINE. DHD LUBE TANK AND A
BOX TO COMMON GROUND (GREEN WIRE)
D
C
CWP/AWS-02/5SA-08
HYDRAULIC TANK BEFORE ADDING OIL.
O 1in DRAWN BY MPS
A CWP/AWS-02GM-42
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 01-09-2002
CONTINUED AT THE TOP
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY D.W.SMITH
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE 01-09-2002 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
(CIRCULARITY) ENG. APPVL. AJAY
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
01/09/02
TITLE
SCHEMATIC ELECTRICAL 240 VAC
SINGLE PHASE AC, DM45/50/L
INFORMATION THEREIN; (2) NOT COPY THE DRAWING; (3) NOT UNSPECIFIED FILLETS PERPENDICULARITY
THIRD ANGLE PROJECTION DATE
MAIN ELECTRICAL BOX

OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING. 120 UP .12 AND RADII TO BE .03 (SQUARENESS)
D
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
FINISHED WEIGHT
SIZE 2657564882 DWG.
REF. NO.
NO. 2657665382 CR
COMM.
2657665382
POSITION
WELD PROCEDURES 1OF 2

CORNERS AND COUNTERSINK SCALE N/A SH
AND ALL MATERIAL COPIED THEREFROM.
TAPPED HOLES TO BODY SIZE. CONCENTRICITY NO.
27 8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ZONE REVISIONS DATE
NO NO BY BY
BLACK
L1 20A
RED D 126
L2 D
WHITE 12 AWG
N
GREEN D 127
GND 110/120 VOLT OUTLET (OPTION)
12 AWG
D 128
12 AWG
D 129
10 AWG
30A
D 130 240 VOLT OUTLET (OPTION)
10 AWG
D 131
10 AWG
30A
30A C
D 132
10 AWG
240 VOLT OUTLET CEE7 (OPTION)
D 133
10 AWG
30A
D 134
10 AWG
MAIN ELECTRICAL BOX
D
WARNING
A
CWP/AWS-02/5SA-08
O 1in DRAWN BY MPS
A CWP/AWS-02GM-42
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 01-09-2002
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY D.W.SMITH
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE 01-09-2002 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
(CIRCULARITY) ENG. APPVL. AJAY
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
01-09-2002
TITLE
SCHEMATIC ELECTRICAL 240 VAC
SINGLE PHASE AC, DM45/50/L
UNSPECIFIED FILLETS PERPENDICULARITY
D
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
FINISHED WEIGHT
SIZE 2657564882 DWG.
REF. NO.
NO. 2657665382 CR
COMM.
2657665382
POSITION
WELD PROCEDURES 2OF 2

CORNERS AND COUNTERSINK DRAWING
SCALE SCALE SH
AND ALL MATERIAL COPIED THEREFROM.
TAPPED HOLES TO BODY SIZE. CONCENTRICITY NO.
28 8 7 6 5 4 3 2 1
Hydraulic Diagram
LIST OF CONTENTS
Part no Description Remarks Page
2657810442 SCHEMATIC,HYD 3 30 - 31
2657400525 SCHEMATIC,AIR R 32 - 33
29
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
DO NOT ORDER PARTS FROM THIS SCHEMAT IC. ROD SUPPORT CYL. -04 NO
ZONE
NO
REVISIONS DATE
BY BY
TOWER RAISING CYLINDER C.S. JACK CYLINDER (2658504068) CHAIN WRENCH CYLINDER TELESCOPIC CYLINDER
CHECK PARTS BOOK FOR CORRECT NUMBER. D.C.S. JACK CYLINDER AIR THROTTLE CYLINDER REFER TO ARCHIVE DRAWING FOR
(2658487996) (2657755589) TR 2.5 DIA, 2, 1.25 ROD (2657039638) (2654418991) PREVIOUS REVISION HISTORY
Q -30/35FT.TWR (2657755589) RET (2658504005) Q
1 COMPONENT MUST BE ADJUSTED AT 5 DIA,48,4 ROD 3.5 DIA, 9, 1.5 ROD 2 DIA, 16, 1 ROD SHT2-F8 & UPDATED SCHEMATIC TO INCLUDE VALVE
5.5 DIA, 48, 3 ROD 5 DIA,48,4 ROD 2.5 DIA, 5, 1.5 ROD F16 2658012196
INSTALLATION TO LIMIT SYSTEM -06 -04 SHT2 MOVED COOLER PIPING TO SHT-2
W/ DBL. HOLDING VALVES W/ DBL. HOLDING VALVES -06 SHT2 USS18 ADDED DML HP TIER 4F COOLING
OPERATION TO THE SPECIFIED SET 4500-5000 PSI TOWER PINNING CYLINDER -04 024 00646 FAN CIRCUIT
08/29/18 SS RR
SET 4500-5000 PSI -12 -12 -06 V
MAXIMUM VALUE. HOIST MOTOR 2 SHT1 H12 ADDED ORIFICE 2657291031
RETRACT
RETRACT
RET-1 (2657531626) C SHT1 H11 ADDED MAIN VALVE ASSY 2659602366
TEST
TEST
(2657632366) EXT 2
SHT1 P1 REMOVED NOTE-3
2 REFERENCE READING. ADJUST RELIEF VALVE FOR TE -06 2.5 DIA, 20, 1.13 ROD C
1
11.9 CU.IN./REV. -06 VALVE, DBL. -06 SLIDING B. O. CYLINDERS
SPECIFIED FAN MOTOR SPEED. ATM-14
DUST COLLECTOR PILOT CHECK -06 V DUST CURTAIN CYLINDER (2657352007)
E E 1
SUN HYD.
XCOA-XXN
SUN HYD.
XCOA-XXN
P C C -04
P
CAVITY
CAVITY
MOTOR (2650462944) 1 2 (2658503998) 1.50 DIA, 8, 1.0 ROD
PLUG
PLUG
-12 -12 (2657003782) VALVE, DBL. 3.5 DIA, 10, 1.75 ROD INDEX MOTOR -06
1.5 CU.IN./REV. ROD CHG CYLS C C PILOT CHECK (2657401135)
C C 1 2 ATM
TEST
(2658488003) 1 2 (2650462944) 1.47 CU.IN/REV
RET
HOLDBACK
EXTEND
EXTEND
TEST
TEST
FEED CYLINDERS R R 3.5 DIA, 10, VALVE, VALVE, DBL.
-12 -12 1.75 ROD -06
SET @4000 PSI
SET @4000 PSI

VALVE, DOUBLE PILOT CHECK
WATER INJECTION
30FT. - 2657484263 DOUBLE PILOT (2650462944) RAISE
SUN HYD.
CABG-LRN
SUN HYD.
CABG-LRN
SHT-2,H-5 V V
35FT. - 2657488827 TEST TEST PILOT CHECK 1 2 LOWER C C
O EXT
C C
RET CHECK (2650462944)
-08
C
1
C
2
-08 1 2 O
(2650462944)
08-41
1 2 V V -06 -06
-16 PULLDOWN -06 -06 V V 1 2
-16 1 2
TEST
-06 -06 -06 -06
EXT
CR1 CR2 CB1 CB2 -04 -04
-06 -06 TO REAR JACK V
1 V
CYLINDER V 2
-06 -06 V
SEE ZONE H16 1 2
N G1 G2 V V V2 VALVE, DBL. N
1 V -04 1
RAISE LOWER 2 -04 PILOT CHECK
RET-11 FITTING, TEST -06 -08 -08 (2650462944)
-06 -06
(2657328676) -06 -06
C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 -06 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1 C2 C1
REGEN VALVE P P
T LOW PRESSURE - 2657448136 -12
30 30 30 30 30 30 15 15 15 10 10 10 10 10 2.5
2:1 HIGH PRESSURE - 2657448144
5:1
VALVE, 6-SPOOL
M -16 P
1
(2657581894)
M
2 PR R PB
GAUGE, HOLDBACK
VALVE SOLENOID (2654413000)
VALVE, 9-SPOOL
(2654438619) 1 (2658503963) 3000psi
1 VALVE, PRESSURE
L P T
CONTROL (HOLDBACK) 2000 2750 1000
L
(2657309536) 3000
100-4500 PSI PSI 1200 1300
LS
2000 3000 2750 LS -04 1200psi
T T
T
(2657167298) TOWER JACK JACK JACK WATER
-16 HOIST -12 ROD ROD CHAIN TOWER TELESCOPIC AIR DUST CAROUSEL SLIDING
REG 500 PSI RET-5 RAISING (DC SIDE) (REAR) (CAB SIDE) INJ. /DC -12
K 1 2 3 4 5 6
RET-6 RET-7 CHANGER SUPPORT WRENCH PINNING CURTAIN THROTTLE FLAP INDEX B.O. K
1 1 2 3 4 5 6 7 8 9
ROTATION MOTOR ROTATION MOTOR
(2657110157) OPT. REAR JACK CYLINDER REAR JACK CYLINDER
(2657209637) (2657755589) (2657755589)
6.00 CU. IN./REV. 4.00 CU. IN./REV. 5DIA,48,4ROD 5 DIA,48,4 ROD
D SEE SHT-2 FOR W/ DBL. HOLDING VLVS. W/ DBL. HOLDING VALVES
OPTIONAL 3 SPEED
DIRECT DRIVE -04 -04
J VALVE, RELIEF ROTARY HEAD
A B J
(2657568487)
H 140 PSI
-06 E E
X (CS AND DCS) PROPEL MOTORS:
Y
ACGT-4.88 CU IN/REV- DM 45/50 ONLY
(CS) PROPEL MOTOR CAT-4.88 CU IN/REV-DM 45/50 ONLY
B A
-16 A ACGT-5.49 CU IN/REV-DML ONLY
FORWARD REVERSE CAT-9.76 CU IN/REV-DML ONLY
I TOP R R I
DRILL PORT
MANIFOLD MANIFOLD PROPEL
(2657350076) (2657350076)
-20
A ATM
TOP -16 -04 -04 -04 -06 -06
PORT -04 BRAKE 2659602366 ORIFICE
-06
B 2657291031
-20 -20 -20 -16 2 1 FROM VALVE, 6-SPOOL
-06
H -16
BOTTOM SEE ZONE N11 H
A B -04 A B -04 -04 A B -04 A B PORT
X Y -04 X Y X Y -04 X Y 3 FITTINGS, TEST
BRAKE (2657328676)
B VALVE, DR/PR CONTROL
P T P T P T P T
DIVERTER VALVES (2654418116)
BOTTOM BR TST3 P
(2657106429) -06
(DCS) PROPEL PORT 1
MOTOR T SEE SHEET-2
G SHIFT G
MINI CHECKS
150 -06 150
-06 500
GAUGE, ROTATION L11
PSI VALVES, TST2 PSI (2654413000)
(2659713438) PSI
HOT OIL SHUTTLE/
X
FLUSHING VALVE, PRESSURE
(2657244352) X CONTROL (TORQUE LIMIT) GAUGE,
-20 Y (2657309536) SUPERCHARGE
100-4500 PSI
-20 -06 1 2 -06 -20 1 2 SEE SHEET-2 PRESSURE
F -06 -06
Y D16
(2656951395) F
CHECK VALVE TST1 -06 P T -06
CHECK VALVE (2657167728) TST4 -04
A VA VB B B VB VA A
(2650347889)
-04 CP1 TQ
1 1
T -08 -04
TPM -08
(DCS) (CS) DM 45/50 SHT-2,C5
4500 SUP-10 4500
E PSI PSI FEED
ALWAYS
3000 PSI VALVE, PRESSURE
MANIFOLD E
-12 (2657024044)
LIMIT DML FEED CONTROL (PULL DOWN) ATM-11
BG AG -20 ATM-10
AG BG 4200 PSI RELIEF (2657309536)
25/30 VALVE 100-4500 PSI
-16 C C FOOT TOWER P3 P2 P1 TRIPLE PUMP
ATM-11 G G MAIN PUMPS 3500 PSI (2657740730)
(2658573088) -04 CP2 35 FOOT TOWER FD -06 -06 P1 = 4.84 CU.IN/REV,
QUICK COUPLING 65
SUP
7.25 CU. IN/REV. 41.44 GPMT ATM
(2657167132) H H P T PSI
D 135-447 135-447 1800X0.91=1978 RPM G1 -04 P2 = 2.75 CU.IN/REV, D
SERVO SERVO 62.1 GPMT 23.8 GPMT
PSI PSI SUC
GAUGE, PULLDOWN P3 = 1.4 CU.IN/REV,
-16 K OP1 OP2 OP3 (2654413000) 11.6 GPMT
SUP-6 KG KG TST5
CHECK VALVE
200 200
(2657167728) -40 -40
PSI PSI SUC-3
VALVES, 2-WAY
D2 D2
(2650429356) 5µ
C D1 D1 C
FILTER 3 µ ROTATION PULLDOWN -04 T P -04 P T -04
(2650630656) -04
-12 SUP-1 SUP-11 5µ
30 PSI BY-PASS QUICK COUPLING
DRAIN QUICK COUPLING ORIFICE SEE HYDRAULIC
(2657167132) ORIFICE
(2657167132) 2651298198 TANK PIPING
MANIFOLD -20 -16 2651298198 RET
ATM-7 ATM-10 DRAWING.
(2657941734) IN OUT
LOCATED
B BELOW
-16
B
PUMPS SUP-4
K -12 UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
O 1 in DRAWN BY SRK
DRN-13
WARNING THE FOLLOWING NOTE DOES NOT
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET
INFORMATION, IS THE PROPERTY OF ATLAS COPCO DRILLING FABRICATION MACHINING STRAIGHTNESS DATE 05/25/06 ATLAS COPCO
APPLY TO THIS PART SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE. DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY TVA
EXPORT OF THIS DRAWING TO COUNTRIES THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- DIM (IN)
OUTSIDE OF THE U. S. IS SUBJECT TO U
EXPORT ADMINISTRATION REGULATIONS.
. S. STRUCTURAL WELDING MUST BE DONE BY WELDERS AND ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES 24
.06
UNDER 24 .01 .005
ROUNDNESS
THAT, EXCEPT AS AUTHORIZED IN WRITING BY ATLAS COPCO (CIRCULARITY) ENG. APPVL. LW
PROCEDURES QUALIFIED IN ACCORDANCE WITH THE ATLAS TITLE
COPCO STRUCTURAL WELDING PROCEDURE CWP/AWS-02
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR
24 TO 120 .09
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
05/25/06 HYDRAULIC SCHEMATIC
INFORMATION THEREIN; (2) NOT COPY THE DRAWING; (3) NOT
DM45/50/L. ELEC/HYD CONTROLS
A COPYRIGHT 2018
AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1
GMAW, SHORT CIRCUIT TRANSFER MODE, IS NOT PER-
DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI- 120 UP .12
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
(SQUARENESS)
THIRD ANGLE PROJECTION
FINISHED WEIGHT
DATE
DWG.
A
ATLAS COPCO
MITTED FOR THIS ASSEMBLY UNLESS APPROVED BY
UPON COMPLETION OF THE NEED TO RETAIN THE DRAWING, OR UNLESS OTHERWISE SPECIFIED, PARALLELISM
SIZE E REF. NO. 2657698938 NO. 2657810442 P
DRILLING SOLUTIONS UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF, REMOVE ALL BURRS AND SHARP POSITION COMM.
ALL RIGHTS RESERVED ATLAS COPCO DRILLING SOLUTIONS. AND ALL MATERIAL COPIED THEREFROM. CORNERS AND COUNTERSINK
SCALE N/A NO. 2657810442 SH
1OF 2
30 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
ZONE REVISIONS DATE
NO NO BY BY
SEE SHT-1 FOR REVISION
Q OPTIONAL
-12 Q
3 SPEED DIRECT DRIVE TO DRAIN MANIFOLD
SOLENOID 1 ROTARY HEAD (2657883357) SOLENOID 2 MAIN FAN MOTOR (2657658031)
(2658335705) (2658335705) METZKE WRENCH OPTION 8.0 CU.IN (131 CC)/REV.
2658012196 -16 -16 USED WITH AIREND HP1250,
HP1450, XL1900 0-1200 RPM
1
2
2A
VALVE, COOLING CONTROL
1A
3A
P
4A
T
A B (2657318875) P
DT
VALVE,REL ELEC V
PROPOR T -20
MANIFOLD S1 RET-10
(2657883373)
TP-5 D -20
SUP
2B
1B
S2 -06
3B
4B
75
TP-4 PSI
P C -16 BOTTOM TOP
O 3 PSI O
B G2 COOLER
G1
REVERSE (2657800419)
RV1 RV2
FITTINGS, TEST
SEE SHT-1 FROM A B (2657328676)
ZONE I-2 P1 TRIPLE
FROM VALVE 2 OF 9 SPOOL FROM VALVE 3 OF 9 SPOOL PUMP -08 -08 CAC FAN MOTOR
A
FORWARD VALVE(ROD SUPPORT) VALVE(CHAIN WRENCH) (2658608025)
TP-3 0.732 CU.IN (12 CC)
A B A B A B A B
N -08 0-1850 RPM N
2B
TO DRAIN MANIFOLD
1A
2A
1B
3B
3A
4B
4A
TP-1 B1 A1 RINEER MOTOR A2 B2 TP-2
(2658468165)
C27 TIER 2 COOLING FAN CIRCUIT
3 3
82 IN /REV 60 IN /REV
ARCTIC COC/HOC
-12 -12 HORTON 54" FAN
DRN
M EXISTING 110cc MOTOR M
3A
3B
1B
1A
4B
4A
2A
2B
30 GPM
2658012196 1100 RPM
1
2
VALVE, COOLING CONTROL
T A B (2657318875)
V3A V1A V1B V4A V4B V2A V2B VALVE,REL ELEC V T -20
V3B
L PROPOR S1 RET-10 L
D -20
SUP
S2 75 -06
P PSI C BOTTOM TOP
WATER INJECTION
8 GPM (2652235207) 3 PSI -16 -20
C3A C3B C1A C1B C4A C4B C2A C2B G1 G2
HOC
2650822147 FITTINGS, TEST
A B
K ROD PUSHER
(2657328676) K
1A1
1B1
4A1
4B2
3B1
3A1
08-42
2B1
2A1
CYLINDER EXISTING RADIATOR/CAC
2658582069 HORTON 54" FAN
4B1
4A2
1B2 80cc MOTOR
15 GPM
TO RECIEVER TANK
08-40 REG 08-80 750 RPM

RET-9
2A2
J J
3A2
2652235207
9.9 in3/rev
WATER TANK
300 GAL
FROM TRIPLE PUMP DML HP TIER 4F COOLING FAN CIRCUIT
UPPER LOWER LOWER UPPER
UPPER JAWS LOWER JAWS
2658581929 TURN 2658581929

08-81
POSITIONING CYLINDERS ALL OTHER AIRENDS: FAN MOTOR (2657657660)
I 2658497999
3 CYLINDERS
2658581957
7.25 CU. IN./REV. 0-1200 RPM I
MANIFOLD 2658581894 2658581964
2 1
-16 -16
08-41
-12
2658012196 TO DRAIN MANIFOLD
VALVE, RELIEF
H 2
(2657142515)
H
1
6-SPOOL VALVE
2
SHT-1 O-11
3
T
G
VALVE,REL ELEC
PROPOR
1
FROM COOLER PKG.
G P1 TRIPLE
G
OUT IN 2 2
PUMP RET-10
BY-PASS CHECK VALVE

(2650261825)
MECHANICAL SHUT-OFF GREASE SYSTEM
F TO GREASE 2658753541 F
INJECTORS
ALL OTHER AIRENDS: FAN MOTOR (2657657660)
EARS COOLING FAN CIRCUIT
7.25 CU. IN./REV. 0-1200 RPM
PUMP,HYDRAULIC -12 -12

(2658595600) DRN AKG 3562.144 FAN MOTOR-19 GPM, 3136PSI
MAX 600 psi -16 -16 F12-80CC
FLOW 3 gpm -08 2657990954
E MAX SPEED 60 CPM 2658012196 HORTON 54" FAN
E
-12
1200 RPM
1
TO DRAIN MANIFOLD
2
P
VALVE, RELIEF
P-OUT T 2
GREASE SIDE (2657142515) T VALVE, COOLING CONTROL
G SYS-P P-RV R
MANIFOLD,PUMP 3 A B (2657318875)
(2658607885) VALVE,REL ELEC V
BP-1 G PROPOR T -20
RET-10
D VENT
EXTERNAL
PILOT S1
D D
1 SUP -20
HYDRAULIC SIDE S2 75 -06
FILL
CV-1
FAST SERVICE FROM COOLER PKG. P PSI C BOTTOM TOP
P1 TRIPLE OUT IN 2 2 -16 -20
P T
PUMP RET-10 G1 3 PSI G2
P-IN T HOC
FITTINGS, TEST
-08 A B (2657328676)
C TO DRN-13 BY-PASS CHECK VALVE C
FROM FROM AKG 3562.146 FAN MOTOR-23 GPM, 2487PSI
TPM -08 SHT-1, B1 (2650261825)
SHT-1 E18 -08 P1 TRIPLE F12-80CC
PUMP 2657990954
HORTON 48" FAN
NON EARS COOLING FAN CIRCUIT 48/.531/30/11.36
1200 RPM
B TIER 4 MTU FINAL 10V1600 COOLING FAN CIRCUIT B

UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
O 1 in DRAWN BY SRK
WARNING THE FOLLOWING NOTE DOES NOT
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET
INFORMATION, IS THE PROPERTY OF ATLAS COPCO DRILLING FABRICATION MACHINING STRAIGHTNESS DATE 05/25/06 ATLAS COPCO
APPLY TO THIS PART SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE. DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY TVA
EXPORT OF THIS DRAWING TO COUNTRIES THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- DIM (IN)
OUTSIDE OF THE U. S. IS SUBJECT TO U
EXPORT ADMINISTRATION REGULATIONS.
. S. STRUCTURAL WELDING MUST BE DONE BY WELDERS AND ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES 24
.06
UNDER 24 .01 .005
ROUNDNESS
THAT, EXCEPT AS AUTHORIZED IN WRITING BY ATLAS COPCO (CIRCULARITY) ENG. APPVL. LW
PROCEDURES QUALIFIED IN ACCORDANCE WITH THE ATLAS TITLE
COPCO STRUCTURAL WELDING PROCEDURE CWP/AWS-02
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR
24 TO 120 .09
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
05/25/06 HYDRAULIC SCHEMATIC
DM45/50/L. ELEC/HYD CONTROLS
A COPYRIGHT
2018
AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1
GMAW, SHORT CIRCUIT TRANSFER MODE, IS NOT PER-
DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI- 120 UP .12
UNSPECIFIED FILLETS
AND RADII TO BE .03
PERPENDICULARITY
(SQUARENESS)
THIRD ANGLE PROJECTION
FINISHED WEIGHT
DATE
DWG.
A
ATLAS COPCO
MITTED FOR THIS ASSEMBLY UNLESS APPROVED BY
UPON COMPLETION OF THE NEED TO RETAIN THE DRAWING, OR UNLESS OTHERWISE SPECIFIED, PARALLELISM
SIZE E REF. NO. 2657698938 NO. 2657810442 P
DRILLING SOLUTIONS UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF, REMOVE ALL BURRS AND SHARP POSITION COMM.
ALL RIGHTS RESERVED ATLAS COPCO DRILLING SOLUTIONS. AND ALL MATERIAL COPIED THEREFROM. CORNERS AND COUNTERSINK
SCALE N/A NO. 2657810442 SH
2OF 2
31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Epiroc operated under the trademark 'Atlas Copco' prior to January 1, 2018 21 22
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
ZONE REVISIONS DATE
NO NO BY BY
REFER TO ARCHIVED DRAWING
Q Q
IR AIREND PIPING
7050 FOR PREVIOUS REVISIONS HISTORY 18-SEP
003 ALL ACT RLH
TO WATER BIT AIR IN 1021 RELEASED ON AC FORMAT AND

26 PREFIXED
2007
INJECTION CAB GAUGE 004 ALL USS19

01659
REDRAWN IN CREO
UPDATED SHEET 1 09/06/19 MK RR
ADDED SHEET 2
2-WAY VALVE 005 SHT-1 USS20 IR AIREND PIPING ONLY:

UPDATED ROUTING FROM 02/14/20 MRF RR
(OPTION)
03234
DM45 LP 0.25 IN COMPRESSOR TO RECEIVER TANK.
3 IN DM45 HP
P DML LP 2 IN P
DML HP
MINIMUM
PRESSURE
GAUGE VALVE 65 PSI LP
135 PSI HP
O 1 IN O
SAFETY
RELIEF
N N
VALVE
SEPARATOR BLOWDOWN
0.375 IN
ELEMENT VALVE
2657777351
2 IN
M 1 IN M
HYDRAULIC TANK
SCAVENGER LINE
PRESSURIZATION SILENCER
0.25 IN 2652187861
L DML HP L
0.5 IN
3 IN DM45 HP 4 IN DML LP
DM45 LP
PNEUMATIC
FILTER
K H 2658489830 K
1.5 IN
0.25 IN
J
D
0.25 IN
J J
PRESSURE
REGULATOR
DUST COLLECTOR (OPTION)

2658489823
E AMOT
I 150 $ I
DHD(OPTION)
0.5 IN
THIS IS FOR
HIGH PRESSURE 1.5 IN
RIGS ONLY B A
OUTLET INLET
H C 0.5 IN H
COOLER
2 IN
HYDRAULIC
G G
TANK BREATHER
2658398009
1.5 IN
ROTARY HEAD
1.5 IN
1.5 IN
F F
VACCUM
SENSOR
1.5 IN
BUTTERFLY VALVE G F LOW H
E E
2657815433 PRESSURE
DETAIL J
D
D LOW-PRESUURE HIGH-PRESUURE H D
DETAIL DETAIL D
HIGH
PRESSURE
DETAIL
C E J C
E AIR AND OIL MIX
ATMOSPHERE AIR
AIR ONLY
LOW-PRESSURE HIGH-PRESSURE OIL

B DETAIL DETAIL E CWP/AWS-02/8620-FC31
WARNING B
D CWP/AWS-2/5-SM/FC-01 EXPORT OF THIS DRAWING TO COUNTRIES
CWP/AWS-02/5SA-08
G F
O 1in DRAWN BY AJAY
G F
A CWP/AWS-02GM-42 THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 1-26-94
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
PART AS INDICATED BY THE "LETTER DESIGNATOR" IN ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES 24 UNDER 24 .01 .005
(CIRCULARITY) ENG. APPVL.
SCHEMATIC,AIR REGULATION
THAT, EXCEPT AS AUTHORIZED IN WRITING BY EPIROC 24 & UP .03 .005 DATE TITLE
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR 24 TO 120 .09 4/3/94
WILL CONFORM TO EPIROC DRILLING SOLUTION ANGULARITY
ANGLES 0 30'
MFG. APPVL.
A A
PROCEDURE CWP/AWS-02 SM/FC-01. ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET
OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING.
120 UP .12
DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
FINISHED WEIGHT
E DWG.
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND
SIZE REF. NO. 2657330151 NO. 2657400525 CR
COMM.
2657400525
POSITION
1OF 2

DML-6OP SCALE N/A NO.
SH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
ZONE NO REVISIONS DATE
NO BY BY
Q
AC AIREND PIPING
Q
BIT AIR IN
CAB GAUGE
P TO WATER P
INJECTION
2-WAY VALVE
(OPTION) 0.25 IN
DM45 LP DM45 HP
O 3 IN DML LP 2 IN O
DML HP
MINIMUM
PRESSURE
VALVE
LP 65 PSI
N HP 135 PSI 1 IN N
M SEPARATOR M
4IN DML LP SAFETY ELEMENT
0.375 IN
RELIEF
VALVE
BLOWDOWN
VALVE
L L
2657777351
DHD(OPTION)
3 IN DM45 HP
DM45 LP
1 IN
SCAVENGER LINE
DML HP
0.25 IN
GAUGE
A
K K
2 IN
SILENCER
B 2652187861
2 IN
J J
0.5 IN 0.25 IN
1.5 IN
ROTARY HEAD
DUST COLLECTOR(OPTION)
PNEUMATIC
I THIS IS FOR FILTER I
HIGH PRESSURE 2658489830
1.5 IN
RIGS ONLY
0.25 IN
0.5 IN
1.5 IN
PRESSURE
H H
REGULATOR
5PSI FOR HIGH 2658489823
PRESSURE OPENING
176 °F FULLY OPEN
OIL STOP VALVE 203 °F COC
G G
FILTER ASSEMBLY
0.5 IN
F VACUUM F
SENSOR
HYDRAULIC TANK
LOW-PRESSURE A BREATHER
DETAIL 265834009
B
E E
BUTTERFLY VALVE
2657815441
A
D D
HIGH-PRESSURE
DETAIL
B
C AIR AND OIL MIX C
AIR ONLY
OIL
B D
WARNING
B
CWP/AWS-02/5SA-08
O 1in DRAWN BY AJAY
A CWP/AWS-02GM-42 THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 1-26-94
ATMOSPHERE
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
PART AS INDICATED BY THE "LETTER DESIGNATOR" IN ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES 24 UNDER 24 .01 .005
(CIRCULARITY) ENG. APPVL.
SCHEMATIC,AIR REGULATION
THAT, EXCEPT AS AUTHORIZED IN WRITING BY EPIROC 24 & UP .03 .005 DATE TITLE
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR 24 TO 120 .09 4/3/94
WILL CONFORM TO EPIROC DRILLING SOLUTION ANGULARITY
ANGLES 0 30'
MFG. APPVL.
A A
PROCEDURE CWP/AWS-02 SM/FC-01. ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET
OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING.
120 UP .12
DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
FINISHED WEIGHT
E DWG.
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND
SIZE REF. NO. 2657330151 NO. 2657400525 CR
COMM.
2657400525
UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF, POSITION

DML-6OP SCALE N/A NO.
SH
2 OF2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
epiroc.com

Planos 9978

Uploaded by

Copyright:

Available Formats

Planos 9978

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Planos 9978

Uploaded by

Copyright:

Available Formats

Drill Master DML-LP

No. 0000 0099 78

STARTER RELAY 1 (NOT USED ON MTU)

GEAR BOX / TOWER SUP. ON COOLER

AIR END / REAR SIDE ON COOLER

STANDARD NIGHT LIGHT PACKAGE

COMP. DISCHARGE TEMP. SENDER

DUST COLLECTOR SIDE WALKWAY

COMP. DISCHARGE TEMP. GAUGE

QSX 15, TIER 3 AND 4 ONLY

CROSSHEAD DUST COLLECTOR

PRO-HEAT HOT BOX OPTION

PLATFORM REAR D.C. SIDE

PLATFORM REAR CAB SIDE

OPTION ON TIER 2& 3

OPTION ON TIER 2& 3

24V OUTLET (OPTION)

(NOT USED ON MTU)

FOR CUSTOMER USE

FUEL LEVEL SENDER

ENGINE OIL PRESS.ENGINE WATER TEMP. VOLTMETER (OPT) ENGINE TACHOMETER

SEE MTU ENG

180A QSX TIER 4 ONLY SEE SHEET 8

CIRCUIT LOCATED ON SIDE OF HYDRAULIC TANK

HYDRAULIC PUMP SUCTION PROTECTION VALVES

ALL OTHERS, ROUTE

INDICATOR LAMP TEST

5 N.O. CONTACT HELD CLOSED WHEN CAROUSEL IS IN STOWED POSITION

ROUTE WIRE 53 TO R4 PIN 2

GEAR BOX / TOWER SUP. ON COOLER

FUEL AND COMP DISCH TEMP GAUGES

STANDARD NIGHT LIGHT PACKAGE

DUST COLLECTOR SIDE WALKWAY

QSX 15, TIER 3 AND 4 ONLY

F.W. MURPHY POWERVIEW 380

CROSSHEAD DUST COLLECTOR

PLATFORM REAR D.C. SIDE

PLATFORM REAR CAB SIDE

SEE SHEET 13 FOR MTU

24V OUTLET (OPTION)

NCS STARTER RELAY

COMP DISCH TEMP

FWM-ES2T-250 FUEL LEVEL SENDER

COMP. DISCHARGE TEMP. SENDER

CIRCUIT LOCATED ON SIDE OF HYDRAULIC TANK

ENGINE TEMP. ENGINE TACH.

OPEN VALVES TO COMPLETE ENGINE START

SEE SHEETS 8 & 13

24 VDC TO 120 VAC

CWP/AWS-2/5-SM/FC-01 EXPORT OF THIS DRAWING TO COUNTRIES

STROBE LIGHT ON PLATFORM REAR OPTION

PROPEL MODE INDICATOR LIGHT OPTION

PROPEL MODE, CAB SIDE, MAIN PUMP

BRAKE RELEASE SOLENOID DR/PR

PULLDOWN CONTROLLER INTERLOCK

BRAKE RELEASE SOLENOID DR/PR

(SPRING RETURN TO NEUTRAL,

NEUTRAL DETECT, ROTATION

REMOTE PROPEL OPTION

3 SPEED DIRECT DRIVE