Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
640 views

Shisham Props Technical Data Sheet

Shisham Stanley Group carried out testing of their entire push-pull brace range following changes to the Australian standard AS3850-2015 for prefabricated concrete elements. The tests were conducted according to the standard's procedures and evaluated statistically. The working load limits presented in the document's table fully comply with the requirements of AS3850-2015.

Uploaded by

Catherine Fatima Mae Leyno
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
640 views

Shisham Props Technical Data Sheet

Shisham Stanley Group carried out testing of their entire push-pull brace range following changes to the Australian standard AS3850-2015 for prefabricated concrete elements. The tests were conducted according to the standard's procedures and evaluated statistically. The working load limits presented in the document's table fully comply with the requirements of AS3850-2015.

Uploaded by

Catherine Fatima Mae Leyno
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

For decades Shisham Stanley Group has been the leading manufacturer and supplier of push-pull panel braces

to the Australian market.


Australian Standard AS3850-2015 (Prefabricated Concrete Elements) has introduced important changes to the brace test method and test
result evaluation. Following the release of AS3850-2015 Shisham Stanley Group carried out an extensive testing of the entire push-pull
brace range. The tests were conducted in compliance with the detailed test procedure and statistical test result evaluation specified by
AS3850-2015. The WLL values presented in the table below fully comply with the AS3850 -2015 test requirements.
SHISHAM BRACES - WLL TABLE
Tested and Rated to Australian Standard AS 3850 – 2015
Closed Intermediate Middle Intermediate Full
Posi on Posi on Posi on Posi on Extension Test Mass
Model No. (kg)
Length WLL Length WLL Length WLL Length WLL Length WLL
(mm) (kN) (mm) (kN) (mm) (kN) (mm) (kN) (mm) (kN)
MP 1
1950 35 2250 35 2550 35 2850 30.5 3150 21.5 M179 24.5
1.95m – 3.15m
MP 2
2450 35 2750 35 3100 26.5 3600 16 4000 11 M178 28.5
2.45m – 4.0m
MICRO MINI
600 35 - - - - - - 850 35 M176 14
0.6m - 0.85m
TRENCH MINI
1000 35 - - 1350 35 - - 1700 35 M175 20
1.0m – 1.7m
SUPA TRENCH
1550 35 - - 2050 35 - - 2500 35 M174 26
1.55m – 2.50m
MINI
2400 35 2800 35 3200 35 3700 31 4100 25 M165 36
2.40m – 4.10m
MINI 2
3100 35 3600 35 4000 35 4400 28.5 4800 21 M172 41
3.1m – 4.80m
SUPA MINI
3100 35 3500 35 3800 35 4100 35 4500 30 M171 47
3.10m – 4.50m
STANDARD
4400 35 5200 30 5800 20 6400 15.5 7000 11.4 M170 61
4.40m – 7.0m
SPECIAL
5700 25 6600 22 7500 11.5 8400 8.5 9400 5.5 M173 70
5.70m – 9.40m
JUMBO
6400 35 7700 22 9000 13 10200 7.5 11300 6 M177 106
6.40 – 11.30m
SUPER JUMBO
8500 25 10000 12 11500 6 13000 - 14500 - M180 137
8.50m – 14.50m
KNEE BRACED - SPECIAL, JUMBO & SUPER JUMBO BRACES INSTALLED WITH KNEE BRACES
SPECIAL - - - - - - - - 9400 20 M181 70

JUMBO - - - - - - 10200 30 11300 24 M182 106

SUPER JUMBO - - - - 11500 24 13000 18.5 14500 12 M183 137


For any designed brace angle the fixing anchor capacity at both ends should be verified. In case braces are loaded in tension the fixing
anchor capacity is likely to be governing the overall bracing system capacity. For extra high tensile loads use Shisham dual foot which is
designed to accommodate two fixing anchors.The maximum WLL value of 35 kN for the panel brace range is determined by the ply bearing
capacity at shear pin connection. In case of tensile loading WLL=35kN applies to all the extension lengths. Micro Mini and Supa Mini braces
can be rated to WLL of more than 35kN (up to 70kN) depending on the load case and type of foot/fixing used. Check the individual brace
brochures or inquire with our team.
EXTRA HEAVY DUTY – HERCULES RANGE
HERCULES 1
2500 100 - - 3000 100 - - 3500 100 M169 110
2.50m – 3.50m
HERCULES 2
4600 100 5300 100 6000 100 6800 100 7500 80 M168 185
4.60m – 7.50m
HERCULES 3
6500 100 7800 100 9000 75 10000 50 11000 35 M167 260
6.50m – 11.0m
Hercules brace range maximum WLL value of 100 kN is a capped-off value determined by capacity of the brace connection bolts.
MASONRY BRACES
MASONRY 3-5
3000 13 - - 4000 6 - - 5000 3 M164 21
3.0m – 5.0m
MODELS COMING SOON – AT R&D STAGE
SAMSON 1, 2 & 3 - - - - - - - - - - - -
TB 1, 2 & 3 - - - - - - - - - - - -
VERTICAL PROP MODELS
OP 1, 2, 3, & 4 - - - - - - - - - - - -

You might also like