General Purpose 3-Phase Induction Motors: Product Catalogue

General Purpose
3-phase
Induction Motors
Energy Efficient
Motors
series 2SIE
Comply with the new efficiency classes

for low-voltage three-phase motors
IEC 60034-30 standard and EU Regulation 640/2009
Product Catalogue
General Purpose 3-phase Induction Motors
Certificates
Cantoni Motor SA
ISO 9001
KEMA
Since September 30, 1999
Number 99515
Besel SA
ISO 9001
Since July 21, 1995
Celma SA
ISO 9001
Germanischer Lloyd
Since June 16, 1995
Number QS-243 HH
ISO 14001
Germanischer Lloyd
Since November 15, 1999
Number EM-1835 HH
Indukta SA
ISO 9001
KEMA
Since April 1, 1993
ISO 14001
KEMA
Since July 1, 2001
Number 2019916
Emit SA
ISO 9001:2008
ISO 14001:2004
PN-N-18001:2004
Polski Rejestr Statków
Since January 23, 2012
Number NC-34
02
CANTONI MOTOR S.A.

3 Maja 28th Street
43-400 Cieszyn, Poland
tel.: +48 33 813 87 00
fax: +48 33 813 87 01
motor@cantonigroup.com
www.cantonimotor.com
BESEL
since 1950
since 1920
since 1878
since 1954
since 1921 EMIT
03
Contents
General information pages 5-14
Introduction to SIE motors
Efficiency of motors
Ratings-tolerances
Standards
Insulation classification
Terminal box
Vibration and noise level
Degree of protection
Mounting arrangements
Bearings
contents
Permissible loads on the shaft end
Housing, endshields
Description of the customised executions
Ordering information
Technical data pages 16-20
Dimensional drawings pages 21-30
List of motor parts pages 31-34
Production program page 35
04
INTRODUCTION
New efficiency classes for the low-voltage three-phase motors (IE = International Efficiency).
Along with the international discussion on energy efficiency a worldwide harmonized energy efficiency classification
system has been established for low-voltage three-phase asynchronous motors.
For many years low-voltage three-phase motors in the European Union have been sold in three efficiency classes EFF3,
EFF2 and EFF1. Aside from this, many different efficiency classification systems have been introduced and well-proven in
many countries all over the world.
This was the reason for the International Electrotechnical Commission IEC to develop and publish an energy efficiency
standard which replaces all previous national issues. In parallel IEC developed and issued a new standard for determining
motor efficiency. The new standard IEC 60034-30 defines and harmonizes worldwide the efficiency classes IE1, IE2 and IE3
for low-voltage three-phase motors in the power range from 0.75 kW to 375 kW (2p=2, 4, 6):
IE1 = Standard Efficiency

IE2 = High Efficiency
IE3 = Premium Efficiency
From now motors can be offered and sold with the new classes IE1, IE2 and IE3.
In that case the efficiency has to be determined according to the new requirements given in the IEC 60034-2-1 standard.
According to the Comission Regulation (EC) No 640/2009 (introduced in July 2009) the required efficiency class
of general-purpose motors (introduced to the market in future) will be as follows:
From 16 June 2011, motors placed for the first-time on the market shall have a minimum efficiency class of IE2.
From 1 January 2015: motors with a rated output between 7.5 - 375 kW shall have a minimum efficiency class of IE3,
or IE2 if they are operated/equipped with electronic speed control (VSD).
From 1 January 2017: motors with a rated output between 0.75 - 375 kW shall have a minimum efficiency class of IE3,
or IE2 if they are operated/equipped with electronic speed control (VSD).
Electronic speed control is carried out using a frequency converter (VSD) that adjusts the
speed of the motor - and therefore the torque produced - based on the energy needed.
2010 2011 2015 2017
IE2 (0,75 - 375kW) Change in the law from 16.06.2011.
IE3 (7,5 - 375kW), IE2 (with VSD)
IE3 (0,75 - 375kW), IE2 (with VSD)
Cantoni Group IE1 motors
Cantoni Group 2SIE motors (IE2)
Cantoni Group has offered energy efficiency motors for several years.
Our motors of SEE series fulfil EFF1 standards according to CEMEP.
We carry out intensive research and measurement of the motors according to the new standards
IEC 60034-30 and IEC 60034-2-1.
05
EFFICIENCY OF MOTORS
Cantoni Motor has in offer general purpose standard efficiency motors of (2) Sg, Sh series which fulfil IE1
class requirements according to the IEC 60034-30 standard.
The present catalogue describes the electric motors which belong to the efficiency class IE2 (High Efficiency)
and motors excluded from the IEC 60034-30 standard (motors with 2p = 8, 10, 12 and with rated output below
0.75kW and above 375kW).
Comparison between the efficiency of Cantoni Group motors (for example 2p=4)
and efficiency class IE1/IE2 requirements according to the IEC 60034-30.
94
Efficiency [%]
86
78
70
0,1 1 10 100 400
PN [kW]
IE2 High Efficiency (Cantoni)

IE1 Standard (Cantoni)
The efficiency class system specified under IEC 60034-30 is valid for low voltage three phase
squirrel cage induction motors with the following specifications:
· Rated voltage up to 1.000 V

· Rated output between 0.75 kW and 375 kW
· Either 2, 4 or 6 poles
· Rated on the basis of continuous duty (S1) or intermittent periodic duty (S3) with
cyclic duration factor of 80% or higher
· Capable of operating direct on-line
· Rated for operating conditions in accordance with IEC 60034-1 (temperature,
installation altitude, etc.)
Motors with flanges, feet and/or shafts with mechanical dimensions different from IEC 60072-1
are also covered by this standard.
06
RATINGS - TOLERANCES
Permissible deviations between real values and catalogue values according to the IEC 60034-1:
Power factor cos ϕ Δcosϕ = -1/6 (1- cosϕN)

Efficiency η Δη = -15%(100-ηN) for PN≤150kW
Δη = -10%(100-ηN) for PN>150kW
Speed n Δn = ±20%(ns-nN) for PN>1kW
Δn = ±30%(ns-nN) for PN≤1kW
Locked rotor current IL/IN Δ(Ir/IN) = +20% (IL/IN)
Locked rotor torque TL/TN min (TL/TN) = -15% (TL/TN)
max (TL/TN) = +25% (TL/TN)
Breakdown torque TB/TN Δ(TB/TN) = -10% (TB/TN)
Moment of inertia J [kgm2] ΔJ = ±10% J
Sound pressure level LpA [dB] ΔLpA = +3 dB /A/
STANDARDS
The electric motors are manufactured according to the international standards:
Rating and performance IEC 60034-1

Methods for determining losses and efficiency IEC 60034-2-1
Classification of degrees of protection IEC 60034-5
Methods of cooling IEC 60034-6
Symbols of construction and mounting arrangements IEC 60034-7
Terminal markings and direction of rotation IEC 60034-8
Noise limits IEC 60034-9
Dimensions and output of electric machines IEC 60072-1
Vibration limits IEC 60034-14
New IEC standards regarding efficiency classes (IEC

60034-30) and efficiency measurements (IEC 60034-2-1)
The resulting efficiency values differ from those obtained under the previous
IEC 60034-2:1996 testing standard.
IE1
It must be noted that the efficiency values are only comparable if they are obtained
using the same measuring method.
EU Regulation 640/2009
IE2
Commission Regulation 640/2009, adapted on 22 July 2009, specifies the
requirements regarding the ecodesign of electric motors and the use of electronic
speed control (VSD).
IE3
All the motors are manufactured in
Quality Assurance System consistent with ISO 9001.
ISO9001
The motors covered by the present catalogue comply with the regulations
and standards effective in other countries, consistent with IEC standards.
IEC
All the motors described in the present catalogue are provided with CE mark.
07
INSULATION CLASSIFICATION
The insulation system of an electric motor is determined by a given insulation Symbols of thermal resistance classes
class on the basis of its thermal resistance. (permissible insulation temperatures
This thermal resistance should be guaranteed by the entire set of electric at 40°C ambient temperature)
insulating materials used in the motor insulating system.
Symbol Temperature [° C]
Thermal resistance classification is related to the temperature of the hotspot
in the insulation occurring during rated operating conditions of the electric
motor, allowing for the highest permissible rise in average temperature. A 105
This rise should be selected so that at the highest permissible ambient E 120
temperature, the temperature of the hotspot in insulation will not exceed the B 130
value assigned to a given thermal resistance class.
F 155
H 180
Insulation class F in an electric motor means that

Ambient temperature
at ambient temperature of 40°C the temperature
Maximal rise of the winding may be max. 105°C with the
temperature rise
additional temperature margin of 10°C
A
Temperature margin (under specified measuring conditions in
40° 60° 5°
accordance with the IEC 60034-1 standard).
Insulation class
B
40° 75° 5°
Class F
The standard motors made by Cantoni Motor in
40° 80° 10°
their basic version have the insulation class F while
the temperature rise is for class B.
F This means longer life for motors.
40° 105° 10°
For special request we can deliver motors equipped
with insulation class H.
H
40° 125° 15° Strengthened insulation system gives possibility
to safe operation with converters.
MOTOR FEET
Motors with frame size ≤ 112 have screwed feet.
Motors with frame size 132 have screwed feet or feet integrated with the motor housing.
Motors with frame size 160 and 180 have feet integrated with the motor housing.
Motors with frame size > 180 up to 315 have feet integrated with the motor housing.
Motors with frame size 315 have screwed feet or feet integrated with the motor housing.
Motors with frame size 355 have feet integrated with the motor housing.
TERMINAL BOX
The terminal boxes of low voltage motors have threaded inlet Low voltage high-power motors contain terminal boxes with
holes designed for mounting cable glands. cable gland seals.
The box contains a terminal board with marked terminals
making possible connection of supply cables. The circuits of thermal protection and anticondensation heaters
are connected to separate terminal boxes.
In addition, terminal boxes may be provided with additional
terminals connected to the ends of thermal protection or Inside the boxes there are special clamps used to ground the
anticondensation heater circuits and extra glands to connect supply cable armouring.
these circuits.
VIBRATION LEVEL AND NOISE LEVEL

The rotor balancing method guarantees that a standard vibration level A is maintained in accordance with
the IEC 60034-14 and a standard sound power level is maintained in accordance with the IEC 60034-9.
On customer’s demand the motors can be made with reduced vibration or noise level. level A
08
INTERNATIONAL PROTECTION IP
According to the IEC 60034-5 standard the electric motors are

provided with IP code which determines the degree of protection
(ensured by the housing) against penetration of solid matter and
fluids.
IP55
PROTECTION AGAINST PENETRATION PROTECTION AGAINST
OF SOLID MATTER PENETRATION OF FLUIDS IK MECHANICAL PROTECTION
1st digit DESCRIPTION 2nd digit DESCRIPTION 3rd digit DESCRIPTION
00 No protection
0 Not protected
Not protected 01 150 g Striking energy:
0 1 Protected against vertically 0.15 J
10 cm
falling drops of water
Protected against
solid bodies larger than 200 g
1 50 mm Protected against 02 Striking energy:
15 10 cm
2 15 vertically falling 0.20 J
drops of water up to 15°
Protected against
solid bodies 60 60
03 250 g Striking energy:
2 Protected against
larger than 0.37 J
12 mm 3 rain up to 60° 15 cm
Protected against 250 g

3 solid bodies Protected against 04 Striking energy:
larger 4 rain falling from any 0.50 J
20 cm
than 2.5 mm direction
Protected against 350 g

4 solid bodies Protected against 05 Striking energy:
5
larger sprayed water 20 cm 0.70 J
than 1 mm from any direction
250 g
Protected against Protected against 06 Striking energy:
5 deposition of dust 6 temporary 40 cm 1J
immersion
7 Protected against immersion 0.5 kg

Totally between 0.15 and 1 m 07 Striking energy:
6 protected against 40 cm
deposition of dust 8 Protected against immersion at 2J
preset pressure and time
1.25 kg
All Cantoni Group standard motors are manufactured with IP 55 degree of 08 Striking energy:
protection according to the standard in force (IEC 60034-5). The following 40 cm 5J
table lists its characteristics.
Each size 80 to 180 motor is equipped with seal rings on the control side 2.5 kg
and on the opposite side. Labyrinth seals protect the motors from size 200
and above. 09 40 cm
Striking energy:
10 J
The terminal board box is sealed with a gasket.
5 kg
Motors with a higher degree of protection are 10
40 cm
Striking energy:
20 J
available on request.
09
MOUNTING ARRANGEMENTS
According to the IEC 60034-7 standard
Horizontal shaft Vertical shaft
Designation Designation
Frame size Frame size

Code II Code I Code II Code I
IM 1001 IM B3 56 ÷ 500 IM 1011 IM V5 56 ÷ 315

without 2SIE 315 M6B,C,D
without SIE 315 M8C,D
IM 1051 IM B6 56 ÷ 280 IM 1031 IM V6 56 ÷ 315

without 2SIE 315 M6B,C,D
without SIE 315 M8C,D
IM 1061 IM B7 56 ÷ 280 IM 2011 IM V15 56 ÷ 355

or IM 2111
IM 1071 IM B8 56 ÷ 280 IM 2031 IM V36 56 ÷ 355

or IM 2131
IM 2001 IM B35 56 ÷ 500 IM 3011 IM V1 56 ÷ 500
IM 2101 IM B34 56 ÷ 132 IM 3031 IM V3 56 ÷ 280
56 ÷ 315
IM 3001 IM B5 without 2SIEK 315 M6B,C,D IM 3611 IM V18 56 ÷ 180
without SIEK 315 M8C,D
IM 3601 IM B14 56 ÷ 132 IM 3631 IM V19 56 ÷ 180
10
PERMISSIBLE LOADS ON THE SHAFT END
Frame Number Horizontal Vertical Frame Number Horizontal Vertical
size of poles operation operation size of poles operation operation
Fp Fp
FR X FR X
Fa2 Fa2
Xmax X0 Xmax X0
Fa1 Fa1
FR(x = 0) FR(x = max) Fp Fa1 Fa2 FR(x = 0) FR(x = max) Fp Fa1 Fa2
[kN] [kN] [kN] [kN]
Sh 56 2 0,20 0,16 0,04 0,03 0,05 2SIE 200 LA 2 3,00 2,50 2,30 1,80 2,90
Sh 56 4 0,25 0,20 0,05 0,04 0,06 2SIE 200 LB 2 3,00 2,50 2,30 1,80 2,90
Sh 56 6 0,25 0,20 0,06 0,05 0,07 2SIE 200 L 4 3,70 3,10 2,80 2,00 3,90
Sh 63 2 0,20 0,16 0,04 0,04 0,06 2SIE 200 LA 6 4,30 3,60 3,60 2,90 4,60
Sh 63 4 0,25 0,20 0,06 0,05 0,07 2SIE 200 LB 6 4,20 3,50 3,60 2,80 4,60
Sh 63 6 0,27 0,22 0,06 0,05 0,07 2SIE 225 S 4 4,20 3,40 3,20 2,50 4,10
Sh 63 8 0,27 0,22 0,07 0,06 0,08 2SIE 225 M 2 3,30 2,80 2,50 1,90 3,30
Sh 71 2 0,29 0,24 0,07 0,05 0,09 2SIE 225 M 4 4,10 3,30 3,20 2,30 4,20
Sh 71 4 0,36 0,30 0,09 0,07 0,11 2SIE 225 M 6 4,70 3,80 4,00 3,00 5,30
Sh 71 6 0,40 0,35 0,10 0,08 0,12 2SIE 250 M 2 4,10 3,40 3,10 2,30 4,10
Sh 71 8 0,40 0,35 0,11 0,09 0,13 2SIE 250 M 4 5,20 4,30 3,90 2,90 5,20
2SIE 80 (Sh) 2 0,33 0,27 0,09 0,06 0,12 2SIE 250 M 6 5,60 4,60 5,00 3,60 6,70
2SIE 80 (Sh) 4 0,44 0,37 0,12 0,09 0,15 2SIE 280 S 2 3,90 3,30 3,10 2,00 4,40
Sh 80 6 0,51 0,42 0,14 0,11 0,17 2SIE 280 S 4 6,70 5,70 5,00 3,60 6,80
Sh 80 8 0,51 0,42 0,17 0,15 0,20 2SIE 280 S 6 7,70 6,60 5,80 4,20 7,70
2SIE 90 2 0,68 0,44 0,68 0,35 0,38 2SIE 280 M 2 3,80 3,20 3,00 1,90 4,50
2SIE 90 4 0,78 0,44 0,78 0,35 0,38 2SIE 280 M 4 6,50 5,50 4,90 3,40 6,90
2SIE 90 6 0,96 0,44 0,96 0,35 0,38 2SIE 280 M 6 7,40 6,30 5,70 3,90 7,90
2SIE 100 2 0,88 0,46 0,90 0,28 0,40 2SIE 315 S 2 3,60 3,10 3,00 1,60 4,70
2SIE 100 4 1,06 0,46 0,98 0,38 0,40 2SIE 315 S 4 6,20 5,20 4,90 3,10 7,20
2SIE 100 6 1,20 0,46 1,10 0,38 0,40 2SIE 315 S 6 7,00 5,90 5,60 3,80 7,80
2SIE 112 2 1,00 0,48 1,00 0,40 0,45 2SIE 315 MA 2 3,30 2,80 2,90 1,40 4,80
2SIE 112 4 1,45 0,48 1,40 0,40 0,45 2SIE 315 MB 2 2,90 2,50 2,80 1,10 5,00
2SIE 112 6 1,62 0,48 1,60 0,40 0,45 2SIE 315 MA 4 5,80 4,80 4,70 2,70 7,30
2SIE 132 2 1,82 0,66 1,90 0,43 0,60 2SIE 315 MB 4 5,40 4,50 4,60 2,40 7,50
2SIE 132 4 2,10 0,66 2,20 0,45 0,60 2SIE 315 MA 6 6,20 5,20 5,30 2,70 8,70
2SIE 132 6 2,80 0,66 2,80 0,50 0,60 2SIE 315 MB 6 5,60 4,80 5,20 2,00 9,20
2SIE 160 2 2,22 0,98 2,30 0,92 0,95 2SIE 315 MC 2 2,80 2,50 2,70 0,60 5,40
2SIE 160 4 2,40 0,98 2,40 0,92 0,95 2SIE 315 MC 4 6,30 5,30 4,30 1,10 8,50
2SIE 160 6 2,85 1,10 2,90 0,98 1,00 2SIE 315 MC 6 7,50 6,30 5,10 1,80 9,20
2SIE 180 2 2,92 1,30 3,00 1,10 1,20 2SIE 315 MD 6 7,50 6,30 5,00 1,80 9,20
2SIE 180 4 3,60 1,30 3,60 1,10 1,30 SIE 315 MC 8 9,40 8,00 6,50 3,90 10,10
2SIE 180 6 4,00 1,80 4,10 1,40 1,70 SIE 315 MD 8 9,20 7,90 5,80 3,00 9,50
PERMISSIBLE LOADS ON THE SHAFT END for motors 2Sg (2p = 8 ÷ 12)
FR(x = 0) FR(x = max) Fp Fa1 Fa2 FR(x = 0) FR(x = max) Fp Fa1 Fa2
[kN] [kN] [kN] [kN]
2Sg 200L8 8 5,10 4,20 4,10 3,40 5,00 2Sg 280S8 8 8,30 6,90 6,60 5,20 8,50
2Sg 200L10A 10 5,50 4,60 4,20 3,50 5,10 2Sg 280S10 10 9,30 7,70 6,70 5,40 8,40
2Sg 200L10B 10 5,50 4,50 4,10 3,40 5,10 2Sg 280S12 12 9,80 8,10 7,00 5,70 8,70
2Sg 200L12 12 5,90 4,90 4,40 3,70 5,40 2Sg 280M8 8 8,00 6,60 6,50 4,90 8,60
2Sg 225S8 8 5,90 4,70 4,70 3,90 5,70 2Sg 280M10 10 8,80 7,30 6,50 5,20 8,20
2Sg 225S10 10 6,50 5,10 4,70 4,00 5,60 2Sg 280M12 12 9,20 7,60 6,80 5,00 9,30
2Sg 225S12 12 6,70 5,30 4,80 4,20 6,00 2Sg 315S8 8 8,40 7,00 7,00 5,00 9,60
2Sg 225M8 8 5,70 4,60 4,60 3,70 5,80 2Sg 315S10 10 9,30 7,70 7,60 5,60 10,20
2Sg 225M10 10 6,30 4,90 5,70 4,40 7,40 2Sg 315S12 12 9,80 8,10 8,00 5,90 10,80
2Sg 225M12 12 6,70 5,30 4,90 3,90 6,20 2Sg 315M8A 8 8,20 6,80 6,90 4,80 9,70
2Sg 250M8 8 6,90 5,60 5,60 4,30 7,20 2Sg 315M8B 8 7,70 6,40 6,80 4,30 10,00
2Sg 250M10 10 7,50 6,20 5,70 4,40 7,40 2Sg 315M10 10 8,40 7,00 7,30 4,80 10,70
2Sg 250M12 12 8,10 6,70 6,10 4,80 7,80 2Sg 315M12A 12 9,30 7,70 7,90 5,50 11,10
2Sg 315M12B 12 9,10 7,60 7,80 5,30 11,20
11
VERSION WITH ROLLER BEARINGS for motors 2SIE315 and 355

Mechanical Size Type of construction No. of poles, 2p D.E. bearing N.D.E. bearing
2SIE 315 ML IM1001 (B3) 4÷6 NU319 EM1C3 6314 C3
2SIE 355 ML IM1001 (B3) 4÷6 NU222 EM1C3 6222 C3
2SIE 355 H IM1001 (B3) 4÷6 NU322 EM1C3 6322 C3
Horizontal mounting Vertical operation

Permissible radial forces Permissible axial forces
FX0 FXmax FA
Motor type Number of poles Length of shaft extension E(mm) kN kN kN
2SIE 315 ML 4 170 27 13 3,5 on request
6 170 29 12 4 on request
2SIE 355 ML 4 210 22 18 5 on request
6 210 23 15 5,5 on request
2SIE 355 H 4 210 27 17 6 on request
6 210 29 15 7 on request
VERSION WITH ROLLER BEARINGS for motors SEE355 and Sh355-500

Mechanical Size Type of construction No. of poles, 2p D.E. bearing N.D.E. bearing
SEE 355 IM1001 (B3) 8 NU222 EM1C3 6222 C3
Sh 355..s IM1001 (B3) 4÷8 NU322 EM1C3 6322 C3
Sh 400..s IM1001 (B3) 4 ÷ 10 on request on request
Horizontal mounting Vertical operation

Permissible radial forces Permissible axial forces
FX0 FXmax FA
Motor type Number of poles Length of shaft extension E(mm) kN kN kN
SEE 355 8 210 24 14 6 on request
Sh 355..s 4 210 27 17 6 on request

8 210 30 15 8 on request
Sh 400
Sh 450 4÷8 on request
Sh 500
PERMISSIBLE LOADS ON THE SHAFT END

Value of radial force FR acting on the shaft end for a Value of force FR acting on any point of the shaft end
given belt pulley diameter is calculated according to (between points X=max and X=0) may be calculated
the following formula: according to the following formula:
where: P - motor output [kW] where: FX0 - value of FR force acting on the beginning of the shaft end
DK - belt pulley diameter [m] FXMAX - value of FR force acting on the end of the shaft end
n - speed [rpm] E - lenght of the shaft end
k - belt tension factor:
for V-belts k=2,2
for flat belts k=3
12
Other specifications dependent on the frame size:
lubrication on the
rotation of the
cable outlets
protection of
Temperature
terminal box
the terminal
Position of
Number of
Number of
sensors in
protection
Degree of
terminals
bearings
Optional
Thermal
winding
Bearing
Glands
Frame
size
box
run
56 IP 55 top 6 1 180° M 20 on request no no
160 IP 55 top 6 2 180° M 40 on request on request on request
180 IP 55 top 6 2 180° M 40 on request on request on request
200 IP 55 top * 6 2 4 × 90° M 50 PTC yes on request
355ML IP 55 top 6 2 4 × 90° M 76 PTC Mark A yes on request
355H IP 55 top 6 2 4 × 90° M 90 Pt 100 yes Pt 100
400 IP 55 top 6 (bars) 3 180° 3×φ55 Pt 100 yes Pt 100
* right position of the terminal box for 2Sg motors series
BEARINGS
Frame Number Bearings Frame Type of No. of D.E. N.D.E.
The bearings in basic version of motors for horizontal and verical duty,
size of poles Size construction poles, 2p bearing bearing
for horizontal and verical duty.

Sh 56 2÷6 6201 2Z C3 2SIE 315 ML IM1001 (B3) 4÷6 6319 C3 6314 C3
Sh 63 2÷8 6202 2Z C3 2SIEL 315 ML IM2001 (B35) 4÷6 6319 C3 6314 C3
Sh 71 2÷8 6203 2Z C3 2SIE 355 ML IM1001 (B3) 2 6217 C3 6217 C3
The bearings in basic

2SIE 80 2÷6 6204 2Z C3 2SIEL 355 ML IM2001 (B35) 4÷6 6222 C3 6222 C3
version of motors
2SIE 90 2÷6 6205 2Z C3 2SIEK 355 ML IM3011 (V1) 4÷6 6322 C3 6322 C3
2SIE 100 2÷6 6206 2Z C3
2SIE 355 H IM1001 (B3) 2 6217 C3 6217 C3
2SIE 112 2÷6 6306 2Z C3
2SIEL 355 H IM2001 (B35) 4÷6 6322 C3 6322 C3
2SIE 132 2÷6 6308 2Z C3
2SIEK 355 H IM3011 (V1) 4÷6 6322 C3 6322 C3
2SIE 160 2÷6 6309 2Z C3
2SIE 180 2÷6 6311 2Z C3
Frame Type of No. of D.E. N.D.E.
2SIE 200 2÷6 6312 C3
excluding 2SIE 315 with 2p=2.
2SIE 225 2÷6 6313 C3 Size construction poles, 2p bearing bearing

2SIE 250 2÷6 6315 C3 SEE 355 IM1001 (B3) 8 6222 C3 6222 C3
2SIE 280 2 6315 C3 SLEE 355 IM2001 (B35) 8 6222 C3 6222 C3
2SIE 280 4÷6 6318 C3
SVEE 355 IM3011 (V1) 8 6322 C3 6322 C3
2SIE 315S,MA, MB 2 6315 C3
Sh 355..s IM1001 (B3) 2 6217 C3 6217 C3
2SIE 315MC 2 6316 C3
SLh 355..s IM2001 (B35) 4÷8 6322 C3 6322 C3
2SIE 315S,MA, MB 4÷6 6318 C3
2SIE 315MC, MD 4÷6 6320C3/6318C3 SVh 355..s IM3001 (V1) 4÷8 6322 C3 6322 C3
SIE 315MC, MD 8 6320C3/6318C3 Sh 400..s IM1001 (B3) 2

SLh 400..s IM2001 (B35) 4 ÷ 10
BEARINGS for 2Sg (2p = 8 ÷ 12) SVh 400..s IM3011 (V1) 4 ÷ 10
Frame Number Bearings Sh 450..s IM1001 (B3) 4 ÷ 12
size of poles
SLh 450..s IM2001 (B35) 4 ÷ 12 on request
2Sg 200 2 ÷ 12 6312 C3
SVh 450..s IM3011 (V1) 4 ÷ 12
2Sg 225 2 ÷ 12 6313 C3
2Sg 250 2 ÷ 12 6315 C3 Sh 500..s IM1001 (B3) 4 ÷ 10
2Sg 280 4 ÷ 12 6317 C3 SLh 500..s IM2001 (B35) 4 ÷ 10

2Sg 315 4 ÷ 12 6318 C3 SVh 500..s IM3011 (V1) 4 ÷ 10
13
HOUSING, END SHIELDS, FEET
Frame Motor End Feet
size [mm] housing shields
56 Aluminium Aluminium Aluminium - screwed

112 Aluminium Cast iron Aluminium - screwed
132 Cast iron Cast iron Cast iron - screwed
160 Cast iron Cast iron Cast iron - integrated
315 Cast iron Cast iron Cast iron - screwed or integrated
In motors series Sh, Sg of frame size 80, 90 and 100mm: on request end shields may be made of cast iron.
In motors series 2SIE of frame size 80 and 90mm: on request end shields may be made of cast iron.
In motors of frame size 132: feet may be integrated with housing.
Motor housing
aluminium
aluminium cast iron
80 90 100 112
cast iron
132 160 180 200 225 250 280 315 355
400 450 500
14
DESCRIPTION OF THE CATALOGUE VERSION
2SIE 315 M 4 B
(2)Sg, Sh, SEE 315 M 8 B
A=Lower power
B=Higher power
C,D=Increased Power
No. of poles
(Speed)
Frame
length
L=long
M=medium
S=short
Shaft h
(in B3)
2SIE 2SIEK 2SIEL

(2)Sg, Sh, SEE (2)SKg, SKh, SVEE, SVh (2)SLg, SLh, SLEE
ORDERING INFORMATION
Orders for motors should specify: When ordering high-power or special purpose motors one
should also indicate:
motor type designation, required direction of rotation,

rated output, required degree of interior protection,
rated speed, method of start-up,
operating duty, method of coupling with the driven unit (gears,
dimensions of belt pulleys, etc.),
supply voltage and connection,
type of machine driven (nature of load), including the
frequency,
moment of inertia J or flywheel effect GD2 brought to the
mounting arrangements, end shield material, motor shaft,
degree of protection, other customer’s specifications.
type of machine driven,
other details of regarding special requests, When ordering spare parts one should specify:
and information concerning additional accessories e.g. full designation of the motor type including its serial
number (provided on the nameplate) or catalogue number,
degree of protection,
thermal protection,
mounting arrangement,
anticondensation heaters,
name of part,
vibration sensors,
number of pieces.
etc.
As part of our development program, we reserve the right

to alter or amend any of the specifications without giving prior notice
15
Totally Enclosed Motors IP 55
rotor current
Breakdown
rotor torque
Moment of
Efficiency
Locked
current
Weight
Locked
output
torque
torque
Power
Inertia
speed
Rated
Rated
Rated
factor
Type
Item
load
Full
PN nN TN ηN [%] cos ϕN IN at rated voltage [A] TL/TN IL/IN TB/TN J
[kW] [HP] [min-1] [Nm] 50% 75% 100% [-] 230V 380V 400V [-] [-] [-] [kgm2] [kg]
2p=2 ns=3000 rpm f=50Hz

1 Sh 56-2A 0,09 0,12 2820 0,30 45 52 62 0,63 0,60 0,35 0,35 2,5 3,4 2,7 0,000076 2,9
2 Sh 56-2B 0,12 0,17 2800 0,41 50 58 65 0,70 0,65 0,38 0,38 2,0 3,0 2,0 0,000095 3,2
3 Sh 63-2A 0,18 0,25 2760 0,62 63 68 70 0,77 0,85 0,50 0,50 2,1 3,4 2,1 0,000175 3,5
4 Sh 63-2B 0,25 0,33 2780 0,85 66 69 72 0,78 1,1 0,65 0,65 2,4 4,0 2,5 0,000235 4,1
5 Sh 71-2A 0,37 0,50 2800 1,25 67 69 71 0,77 1,75 1,0 1,0 2,2 4,4 2,2 0,000389 5,0
6 Sh 71-2B 0,55 0,75 2790 1,88 69 72 75 0,82 2,35 1,35 1,35 2,0 4,0 2,1 0,000484 6,0
7 2SIE 80-2A 0,75 1 2840 2,52 72,0 76,5 79,0 0,74 3,3 1,9 1,9 3,2 5,0 3,0 0,0003 8,5 IE2
8 2SIE 80-2B 1,1 1,5 2840 3,7 77,0 80,0 80,0 0,75 4,8 2,7 2,7 3,4 5,5 3,4 0,0011 9,8 IE2
TECHNICAL DATA
9 2SIE 90S2 1,5 2 2880 5 80,0 82,0 81,8 0,81 5,7 3,4 3,3 3,3 7,6 3,4 0,0014 13,9 IE2
10 2SIE 90L2 2,2 3 2870 7,3 83,4 84,4 83,5 0,81 8,2 4,9 4,7 3,7 7,3 3,7 0,0016 17,3 IE2
11 2SIE 100L2 3 4 2905 9,8 82,1 84,4 84,6 0,83 10,7 6,5 6,2 3,1 8,3 3,3 0,0039 23,0 IE2
12 2SIE 112M2 4 5,5 2915 13,1 86,9 87,3 86,3 0,87 13,4 8,1 7,7 2,4 8,5 2,7 0,006 33,5 IE2
13 2SIE 132S2A 5,5 7,5 2930 17,9 88,5 89,2 87,5 0,90 17,5 10,6 10,1 2,7 8,8 3,4 0,014 59,5 IE2
14 2SIE 132S2B 7,5 10 2920 24,5 88,2 89,1 88,6 0,92 23,1 14,0 13,2 2,7 8,5 3,3 0,017 70,8 IE2
15 2SIE 160M2A 11 15 2940 35,7 89,4 90,3 90,0 0,87 35,3 21,3 20,3 2,0 7,2 2,7 0,042 96 IE2
16 2SIE 160M2B 15 20 2935 48,8 90,6 91,0 90,3 0,89 46,9 28,4 26,9 2,0 7,0 2,8 0,048 103 IE2
17 2SIE 160L2 18,5 25 2935 60,2 92,2 92,3 91,5 0,91 55,8 33,8 32,1 2,3 7,7 2,9 0,059 118 IE2
18 2SIE 180M2 22 30 2945 71,3 90,8 91,7 91,3 0,88 68,7 41,6 39,5 2,6 7,5 3,2 0,062 156 IE2
19 2SIE 200L2A 30 40 2953 97 92,0 92,5 92,0 0,90 91 55 52 2,1 6,0 2,4 0,15 266 IE2
20 2SIE 200L2B 37 50 2954 120 92,7 93,1 92,6 0,91 110 67 63 1,8 6,1 2,6 0,18 290 IE2
21 2SIE 225M2 45 60 2970 145 93,3 93,8 93,1 0,88 138 83 79 2,0 6,6 2,6 0,26 380 IE2
22 2SIE 250M2 55 75 2963 177 94,0 94,1 93,6 0,91 162 98 93 1,7 6,0 2,2 0,42 492 IE2
23 2SIE 280S2 75 100 2978 241 93,4 94,1 94,0 0,91 220 133 127 1,7 6,7 2,4 0,76 655 IE2
24 2SIE 280M2 90 125 2978 289 94,0 94,6 94,4 0,91 263 159 151 1,8 7,0 2,8 0,95 688 IE2
25 2SIE 315S2 110 150 2978 353 94,5 94,9 94,6 0,92 317 192 182 1,9 6,9 2,9 0,98 860 IE2
26 2SIE 315M2A 132 175 2979 423 94,8 95,1 94,9 0,92 380 230 218 2,1 7,8 3,0 1,15 925 IE2
27 2SIE 315M2B 160 220 2980 513 94,9 95,4 95,2 0,92 459 278 264 2,4 8,8 3,4 1,40 1005 IE2
28 2SIE 315M2C* 200 270 2979 641 95,5 95,6 95,4 0,93 - 342 325 2,3 8,1 3,1 1,74 1183 IE2
29 2SIE 355ML2 200 270 2987 639 94,0 95,2 95,6 0,90 - 353 336 1,9 8,0 3,4 2,8 1600 IE2
30 2SIE 355ML2A 250 340 2982 801 94,7 95,6 95,7 0,91 - 436 414 1,8 7,0 2,8 2,8 1600 IE2
31 2SIE 355ML2B 315 430 2982 1009 95,0 95,7 95,7 0,91 - 550 522 1,9 7,3 3,0 3,0 1680 IE2
32 2SIE 355H2D 355 480 2985 1136 94,7 95,5 95,7 0,91 - 619 588 1,7 7,4 2,7 4,9 2140 IE2
33 Sh 355H2Es 400 540 2985 1280 95,5 96,6 96,7 0,91 - - 656 1,6 8,0 2,8 5,7 2160
34 Sh 400H2Cs 450 610 2983 1441 95,5 96,3 96,5 0,91 - - 741 1,3 6,6 2,6 6,7 2800
35 Sh 400H2Ds 500 680 2985 1600 95,8 96,5 96,6 0,91 - - 821 1,4 7,2 2,8 7,7 2800
36 Sh 400H2Es 560 760 2989 1789 95,9 96,7 96,9 0,90 - - 927 1,7 8,0 3,0 8,7 3100
37 Sh 400H2Es 600 816 2987 1918 96,0 96,8 97,0 0,91 - - 981 1,7 8,0 3,0 8,7 3100
* insulation class F/F
16
rotor current
Breakdown
rotor torque
Moment of
Efficiency
Locked
current
Weight
Locked
output
torque
torque
Power
Inertia
speed
Rated
Rated
Rated
factor
Type
Item
load
Full
PN nN TN ηN [%] cos ϕN IN at rated voltage [A] TL/TN IL/IN TB/TN J
2p=4 ns=1500 rpm f=50Hz

38 Sh 56-4A 0,06 0,08 1400 0,41 40,0 48,0 50,0 0,58 0,52 0,30 0,30 2,0 2,8 2,3 0,00015 2,6
39 Sh 56-4B 0,09 0,12 1400 0,61 54,0 58,0 58,0 0,60 0,70 0,40 0,40 2,1 2,6 2,3 0,00019 2,8
40 Sh 63-4A 0,12 0,17 1380 0,83 56,0 60,0 60,0 0,63 0,80 0,45 0,45 1,9 2,6 2,0 0,00024 3,5
41 Sh 63-4B 0,18 0,25 1340 1,25 52,0 55,0 57,0 0,66 1,2 0,70 0,70 2,0 2,6 2,0 0,00031 4,1
42 Sh 71-4A 0,25 0,33 1380 1,73 60,0 63,0 66,0 0,64 1,5 0,85 0,85 2,0 3,0 2,0 0,00061 5,1
43 Sh 71-4B 0,37 0,50 1370 2,6 64,0 67,0 70,0 0,68 2,2 1,25 1,25 2,1 3,1 2,1 0,00077 5,8
44 Sh 80-4A 0,55 0,75 1400 3,75 70,0 69,0 73,0 0,69 2,8 1,6 1,6 2,0 3,6 2,1 0,00158 7,5
IE2 45 2SIE 80-4B 0,75 1 1400 5,12 70,0 77,0 80,0 0,65 3,7 2,2 2,2 3,2 4,2 3,1 0,00209 9,7
IE2 46 2SIE 90S4 1,1 1,5 1425 7,4 79,1 81,3 81,4 0,76 4,5 2,7 2,6 2,4 5,7 2,8 0,0029 16,3
IE2 47 2SIE 90L4 1,5 2 1425 10,1 81,2 83,2 82,8 0,76 6,0 3,6 3,4 2,6 6,2 2,9 0,0036 18
IE2 48 2SIE 100L4A 2,2 3 1440 14,6 84,6 85,5 84,7 0,83 7,9 4,8 4,5 2,4 7,3 2,8 0,007 25,5
TECHNICAL DATA
IE2 49 2SIE 100L4B 3 4 1445 19,8 83,7 85,7 85,5 0,75 11,8 7,1 6,8 3,1 8,0 3,2 0,0076 27,5
IE2 50 2SIE 112M4 4 5,5 1450 26,3 86,9 87,7 87,0 0,79 14,6 8,8 8,4 2,0 6,7 2,9 0,0115 35,5
IE2 51 2SIE 132S4 5,5 7,5 1460 36 87,0 88,2 88,0 0,80 19,6 11,9 11,3 2,4 8,3 3,1 0,031 69
IE2 52 2SIE 132M4 7,5 10 1460 49,1 88,5 89,2 88,7 0,80 26,5 16,1 15,3 2,5 7,7 3,3 0,036 73,5
IE2 53 2SIE 160M4 11 15 1470 71,5 89,3 90,3 89,8 0,81 38,0 23,0 21,8 2,0 7,1 2,8 0,057 106
IE2 54 2SIE 160L4 15 20 1470 97,4 90,7 91,3 90,6 0,81 51,3 31,1 29,5 2,3 7,5 3,3 0,07 127
IE2 55 2SIE 180M4 18,5 25 1470 120,2 90,2 91,3 91,2 0,86 59,2 35,8 34,0 2,9 7,8 3,6 0,139 169
IE2 56 2SIE 180L4 22 30 1460 143,9 91,4 92,0 91,6 0,86 70,1 42,4 40,3 2,9 7,6 3,3 0,144 180
IE2 57 2SIE 200L4 30 40 1474 194 93,3 93,2 92,4 0,89 92 55 53 2,1 5,8 2,5 0,31 284
IE2 58 2SIE 225S4 37 50 1484 238 92,7 93,3 93,1 0,86 116 70 67 2,3 7,4 2,8 0,49 368
IE2 59 2SIE 225M4 45 60 1484 290 93,1 93,8 93,6 0,86 140 85 81 2,2 7,4 2,7 0,57 404
IE2 60 2SIE 250M4 55 75 1482 354 93,2 93,7 93,5 0,90 164 99 94 1,9 5,9 2,4 0,79 478
IE2 61 2SIE 280S4 75 100 1488 481 94,7 94,8 94,2 0,90 222 134 128 1,8 6,2 2,2 1,37 678
IE2 62 2SIE 280M4 90 125 1488 578 93,8 94,4 94,2 0,89 269 163 155 2,1 7,1 2,7 1,50 700
IE2 63 2SIE 315S4 110 150 1488 706 94,9 95,1 94,6 0,90 324 196 186 2,0 6,6 2,5 1,85 875
IE2 64 2SIE 315M4A 132 175 1487 848 95,5 95,5 95,0 0,91 383 232 220 1,9 6,7 2,4 2,25 957
IE2 65 2SIE 315M4B 160 220 1489 1026 95,3 95,5 95,2 0,90 469 284 270 2,7 8,3 3,0 2,59 1012
IE2 66 2SIE 315M4C* 200 270 1486 1285 95,6 95,6 95,2 0,91 - 351 333 2,1 7,1 2,5 3,24 1198
IE2 67 2SIE 315ML4 200 270 1487 1285 95,1 95,8 95,7 0,87 - 365 347 2,3 7,2 2,4 3,3 1198
IE2 68 2SIE 355ML4 200 270 1490 1282 95,2 95,8 95,8 0,89 - 356 339 2,0 7,4 2,4 5,3 1680
IE2 69 2SIE 355ML4A 250 340 1489 1603 95,6 96,0 95,9 0,89 - 445 423 2,0 7,3 2,4 5,3 1680
IE2? 70 2SIE 355ML4B 315 430 1489 2020 95,6 96,0 95,9 0,90 - 555 527 2,2 7,6 2,5 6,4 1810
IE2 71 2SIE 355H4D 355 480 1488 2278 95,7 96,0 95,9 0,88 - 639 607 1,6 6,5 2,2 7,8 2175
72 Sh 355H4Es 400 540 1489 2566 96,4 96,8 96,7 0,88 - 715 678 1,8 7,0 2,3 8,7 2275
73 Sh 400H4Cs 450 610 1490 2884 96,3 96,9 96,9 0,88 - 796 762 1,6 7,6 2,6 12,3 2920
74 Sh 400H4Ds 500 680 1491 3203 96,2 96,7 96,7 0,88 - 891 848 1,6 7,5 2,6 13,6 3100
75 Sh 400H4Es 560 760 1491 3587 96,6 97,0 97,0 0,87 - 987 958 1,7 7,6 2,6 15,0 3220
76 Sh 400H4Fs 630 850 1491 4035 96,7 97,1 97,1 0,87 - 1114 1076 1,9 8,4 2,8 16,5 3440
77 Sh 450H4Bs 710 960 1492 4545 96,6 97,1 97,1 0,88 - - 6962 1,6 7,0 2,5 27,1 4000
78 Sh 450H4Cs 800 1080 1494 5114 96,8 97,1 97,1 0,89 - - 7742 1,6 6,8 2,6 31,6 4400
79 Sh 450H4Ds 900 1210 1493 6757 96,8 97,2 97,2 0,88 - - 8812 1,0 7,3 2,5 35,4 4620
80 Sh 450H4Es 1000 1350 1493 6397 96,8 97,3 97,3 0,89 - - 9662 1,5 7,3 2,5 38,0 4700
81 Sh 500H4Cs 1120 1510 1495 7155 96,7 97,4 97,4 0,87 - - 11072 0,8 6,9 2,5 58,4 6100
82 Sh 500H4Ds 1250 1680 1495 7985 96,7 97,4 97,5 0,87 - - 12342 0,8 7,5 2,7 65,2 6600
83 Sh 500H4Es 1400 1880 1494 8949 96,9 97,5 97,5 0,88 - - 13672 0,7 6,4 2,4 66,5 6900
2 - at rated voltage 690V
17
rotor current
rotor torque
Breakdown
Moment of
Efficiency
Locked
current
Weight
Locked
output
torque
torque
Power
Inertia
speed
Rated
Rated
Rated
factor
Type
Item
load
Full
PN nN TN hN [%] cos jN IN at rated voltage [A] TL/TN IL/IN TB/TN J
2p=6 ns=1000 rpm f=50Hz
84 Sh 56-6B 0,06 0,08 870 0,64 44 46 50 0,65 1,1 0,65 0,65 1,3 1,8 1,5 0,00019 2,8
85 Sh 63-6A 0,09 0,12 820 1,05 26 32 40 0,75 0,8 0,45 0,45 1,15 1,9 1,3 0,00024 3,5
86 Sh 63-6B 0,12 0,17 870 1,30 38 44 50 0,65 1,15 0,65 0,65 1,3 1,8 1,1 0,00031 4,1
87 Sh 71-6A 0,18 0,25 890 1,93 47 54 57 0,68 1,3 0,75 0,75 1,9 2,6 1,9 0,00074 4,8
88 Sh 71-6B 0,25 0,33 860 2,78 45 52 55 0,79 1,75 1,0 1,0 1,6 2,0 1,6 0,00095 5,6
89 Sh 80-6A 0,37 0,50 910 3,88 61 63 64 0,65 2,4 1,4 1,4 2,0 3,0 2,1 0,00169 7,4
90 Sh 80-6B 0,55 0,75 900 5,84 62 65 67 0,70 3,1 1,8 1,8 1,9 2,7 2,0 0,00207 8,7
91 2SIE 90S6 0,75 1 925 7,7 74,3 76,8 75,9 0,70 3,5 2,1 2,0 2,2 4,2 2,6 0,0028 16,5 IE2
92 2SIE 90L6 1,1 1,5 910 11,5 77,8 79,0 78,1 0,71 5,0 3,0 2,9 2,4 4,3 2,7 0,0032 18,2 IE2
93 2SIE 100L6 1,5 2 950 15,1 78,4 80,7 80,3 0,73 6,4 3,9 3,7 2,4 5,5 2,6 0,01 22 IE2
TECHNICAL DATA
94 2SIE 112M6 2,2 3 955 22 82,0 83,1 82,3 0,75 8,9 5,4 5,1 2,3 5,9 2,7 0,0177 32 IE2
95 2SIE 132S6 3 4 950 30,2 83,1 84,3 83,3 0,79 11,4 6,9 6,6 2,0 5,5 2,7 0,025 50 IE2
96 2SIE 132M6A 4 5,5 950 40,2 85,5 85,9 84,6 0,79 15,0 9,1 8,6 2,4 6,3 2,8 0,032 62 IE2
97 2SIE 132M6B 5,5 7,5 950 55,3 86,5 86,8 86,0 0,81 19,8 12,0 11,4 2,6 6,6 3,1 0,04 72 IE2
98 2SIE 160M6 7,5 10 960 74,6 88,2 88,5 87,4 0,81 26,6 16,1 15,3 2,3 6,7 3,1 0,072 100 IE2
99 2SIE 160L6 11 15 960 109,4 89,3 89,6 88,7 0,82 38,0 23,0 21,8 2,5 7,1 3,1 0,096 125 IE2
100 2SIE 180L6 15 20 975 146,9 89,1 90,1 89,7 0,82 51,2 31,0 29,4 2,8 6,3 2,4 0,22 170 IE2
101 2SIE 200L6A 18,5 25 987 179 89,7 90,8 90,7 0,80 64 38,5 37 2,0 5,6 2,2 0,50 283 IE2
102 2SIE 200L6B 22 30 987 213 90,1 91,0 90,9 0,80 76 46 44 2,1 5,7 2,2 0,57 294 IE2
103 2SIE 225M6 30 40 988 290 91,5 92,2 91,9 0,83 99 60 57 1,9 6,0 2,2 0,82 379 IE2
104 2SIE 250M6 37 50 992 356 91,8 92,7 92,6 0,83 121 73 69 2,0 6,9 2,7 1,23 436 IE2
105 2SIE 280S6 45 60 992 432 92,5 93,2 92,8 0,80 153 93 88 2,1 6,6 2,4 1,52 633 IE2
106 2SIE 280M6 55 75 993 529 93,1 93,6 93,3 0,81 183 111 105 2,2 6,9 2,5 1,85 690 IE2
107 2SIE 315S6 75 100 992 722 94,0 94,5 94,2 0,82 244 148 140 2,4 7,1 2,6 2,39 895 IE2
108 2SIE 315M6A 90 125 993 866 94,4 94,8 94,5 0,82 292 176 168 2,6 7,5 2,7 2,81 953 IE2
109 2SIE 315M6B 110 150 993 1058 94,5 95,0 94,7 0,82 356 215 204 2,6 7,6 2,7 3,46 1106 IE2
110 2SIE 315M6C* 132 175 991 1271 95,0 95,1 94,7 0,83 - 255 242 2,4 6,8 2,5 4,21 1226 IE2
111 2SIE 315M6D* 160 220 990 1543 95,1 95,2 94,8 0,83 - 308 293 2,2 6,2 2,3 4,36 1233 IE2
112 2SIE 315ML6 160 220 987 1548 94,4 95,0 94,8 0,84 - 305 290 2,1 6,3 2,4 3,5 1240 IE2
113 2SIE 355ML6A 200 270 989 1931 95,1 95,6 95,5 0,86 - 370 351 2,1 7,0 2,4 7,2 1720 IE2
114 2SIE 355ML6B 250 340 990 2412 95,5 95,9 95,7 0,86 - 462 438 2,2 7,1 2,4 8,6 1920 IE2
115 2SIE 355H6C 315 430 992 3033 95,6 95,9 95,7 0,86 - 582 552 1,9 7,0 2,2 12,7 2370 IE2
116 2SIE 355H6D 355 480 991 3421 95,5 95,9 95,7 0,86 - 655 623 1,8 6,9 2,3 13,6 2480 IE2
117 Sh 400H6Bs 400 540 992 3851 95,6 96,3 96,3 0,84 - - 714 1,7 6,8 2,2 18,2 3050
118 Sh 400H6Cs 450 610 993 4328 95,8 96,3 96,0 0,83 - - 815 1,5 7,5 2,5 19,4 3250
119 Sh 450H6As 500 680 994 4804 96,6 96,9 96,8 0,88 - - 4912 1,2 6,7 2,6 36,5 3800
120 Sh 450H6Bs 560 760 994 5380 96,7 97,0 96,9 0,88 - - 5492 1,2 6,8 2,6 40,6 4300
121 Sh 450H6Cs 630 850 994 6053 96,7 97,1 97,0 0,89 - - 6112 1,3 7,0 2,6 45,0 4500
122 Sh 450H6Ds 710 960 994 6821 96,5 96,8 96,8 0,89 - - 6902 1,4 7,4 2,6 50,0 4890
123 Sh 500H6As 800 1080 995 7678 96,7 97,1 97,0 0,86 - - 8022 0,9 5,8 2,4 61,5 6200
124 Sh 500H6Bs 900 1210 995 8638 96,8 97,1 97,0 0,87 - - 8932 1,0 6,0 2,2 67,5 6550
125 Sh 500H6Cs 1000 1350 995 9598 96,4 97,0 97,1 0,86 - - 10022 1,0 6,4 2,5 70,0 6700
126 Sh 500H6Ds 1120 1510 996 10739 96,4 97,1 97,2 0,85 - - 11342 1,1 7,0 2,6 80,0 7130
127 Sh 500H6Es 1250 1680 996 11985 96,4 97,1 97,2 0,85 - - 12662 1,1 7,1 2,6 84,6 7460
2 - at rated voltage 690V

18
Weight (IMB3)
rotor current
rotor torque
Breakdown
Moment of
Efficiency
Locked
Locked
current
torque
torque
output
Power
inertia
speed
Rated
Rated
Rated
factor
Type
Item
load
Full
PN nN TN ηN [%] at % of full load cos ϕN IN at rated voltage TL/TN IL/IN Tb/TN J
[kW] [HP] [min-1] [Nm] 50% 75% 100% [-] [A]230V [A]380V [A]400V [-] [-] [-] [kgm2] [kg]
2p=8 ns=750 rpm
128 Sh 63-8A 0,04 0,05 670 0,57 20 31 35 0,60 0,6 0,35 0,35 1,6 1,7 1,7 0,00024 3,5
129 Sh 63-8B 0,06 0,08 660 0,87 20 24 28 0,48 1,1 0,65 0,65 1,4 1,5 1,6 0,000307 4,1
130 Sh 71-8A 0,09 0,12 680 1,26 25 31 35 0,5 1,3 0,75 0,75 1,9 1,9 1,9 0,000736 4,7
131 Sh 71-8B 0,12 0,17 670 1,71 40 45 47 0,63 1,25 0,7 0,7 1,7 1,9 1,8 0,000946 5,6
132 Sh 80-8A 0,18 0,25 680 2,53 43 51 53 0,57 1,55 0,9 0,9 1,8 2,3 2,0 0,001693 7,2
133 Sh 80-8B 0,25 0,33 680 3,51 52 55 57 0,6 2,1 1,2 1,2 1,7 2,5 1,7 0,00207 8,7
134 Sh 90S-8 0,37 0,5 695 5,08 54,2 60,8 63,4 0,59 2,5 1,5 1,4 1,7 2,9 2,3 0,0021 13,4
135 Sh 90L-8 0,55 0,75 675 7,78 60,4 65,3 65 0,64 3,3 2 1,9 1,7 2,8 1,9 0,0024 15,3
136 Sg 100L-8A 0,75 1 710 10,1 65,9 70,5 71,1 0,66 4 2,4 2,3 1,4 3,5 1,9 0,009 23,6
137 Sg 100L-8B 1,1 1,5 705 14,9 67,6 71,8 72,2 0,65 5,9 3,6 3,4 1,6 3,6 1,9 0,01 26,3
TECHNICAL DATA
138 Sg 112M-8 1,5 2 720 19,9 72,5 76,2 76,8 0,71 6,9 4,2 4,0 1,9 4,6 2,3 0,0192 31
139 Sg 132S-8 2,2 3 710 29,6 75,4 78,2 78 0,74 9,6 5,8 5,5 2,0 4,7 2,4 0,033 53
140 Sg 132M-8 3 4 710 40,4 78,5 80,7 80 0,74 12,7 7,7 7,3 2,3 5,0 3,0 0,044 65
141 Sg 160M-8A 4 5,5 705 54,2 81,5 82,7 81,5 0,76 16,2 9,8 9,3 2,2 5,0 2,7 0,06 85
142 Sg 160M-8B 5,5 7,5 710 74 82,1 83,7 83 0,75 22,2 13,4 12,8 2,7 5,5 3,0 0,077 95
143 Sg 160L-8 7,5 10 705 102 84,5 85,5 84,5 0,78 28,6 17,3 16,4 2,7 5,8 3,0 0,102 115
144 Sg 180L-8 11 15 730 144 87,7 89,2 89 0,76 40,8 24,7 23,5 2,0 5,5 2,4 0,213 165
145 2Sg 200L8 15 20 733 195 88,8 90 89,5 0,83 51 30,5 29,1 2,2 5,5 2,1 0,45 255
146 2Sg 225S8 18,5 25 735 240 88,8 90 89,5 0,81 64 39 37 2,0 5,6 2,0 0,58 280
147 2Sg 225M8 22 30 735 286 90,0 90,8 90,4 0,80 76 46 44 2,0 5,2 1,8 0,68 315
148 2Sg 250M8 30 40 738 388 91,0 92 91,5 0,84 98 59 56 2,5 6,3 2,1 1,27 430
149 2Sg 280S8 37 50 737 479 92,0 93,1 92,8 0,83 121 73 69 2,0 5,3 1,8 1,47 535
150 2Sg 280M8 45 60 737 583 92,0 92,8 92,5 0,84 145 88 84 2,1 5,4 2,0 1,8 590
151 2Sg 315S8 55 75 735 715 92,0 93,0 92,7 0,81 184 111 106 2,0 5,3 1,9 2,16 720
152 2Sg 315M8A 75 100 737 972 92,5 93,5 93,2 0,82 246 149 142 2,5 6,2 1,9 2,29 750
153 2Sg 315M8B 90 125 737 1166 92,5 93,5 93,2 0,82 296 179 170 2,4 6,5 1,9 2,86 840
154 SIE 315M8C1 110 150 737 1425 92,3 93,1 93,3 0,79 375 227 215 2,3 5,4 2,2 3,46 1105
155 SIE 315M8D1 132 175 734 1717 92,7 93,3 93,2 0,81 439 266 252 2,3 5,4 2,2 3,69 1136
156 SEE 355ML8A 160 220 739 2068 95,1 95,5 95,0 0,80 - - 305 1,6 5,8 2,0 7,0 1680
157 SEE 355ML8B 200 270 740 2581 95,1 95,6 95,2 0,79 - - 384 1,8 6,2 2,1 7,7 1750
158 Sh 355H8Ds 250 340 742 3218 95,5 96,0 95,6 0,78 - - 484 1,3 6,0 2,0 12,9 2440
159 Sh 355H8Es 315 430 742 4054 95,6 96,0 95,8 0,78 - - 609 1,3 6,0 2,0 16,0 2590
160 Sh 400H8Ds 355 480 742 4569 95,3 95,9 95,9 0,77 - - 695 1,2 5,8 2,0 18,8 3200
161 Sh 400H8Es 400 540 742 5148 95,4 96,0 96,0 0,77 - - 782 1,2 5,9 2,0 21,0 3350
162 Sh 450H8Bs 450 610 746 5761 95,5 96,3 96,4 0,78 - - 5012 1,0 5,8 2,1 41,6 4400
163 Sh 450H8Cs 500 680 746 6401 95,5 96,3 96,4 0,78 - - 5572 1,0 5,8 2,1 46,0 4600
164 Sh 450H8Ds 560 760 746 7169 95,6 96,4 96,5 0,78 - - 6232 1,0 5,7 2,1 49,0 4770
165 Sh 450H8Es 630 850 746 8065 95,8 96,4 96,5 0,79 - - 6922 1,0 5,6 2,0 53,8 4980
166 Sh 500H8Bs 710 960 746 9089 96,0 96,6 96,7 0,81 - - 7582 1,0 6,0 2,4 92,4 6680
167 Sh 500H8Cs 800 1080 746 10241 96,0 96,6 96,7 0,80 - - 8652 1,1 6,3 2,5 95,8 6800
168 Sh 500H8Ds 900 1210 746 11522 96,1 96,8 96,9 0,80 - - 9712 1,0 6,0 2,4 108 7240
169 Sh 500H8Es 1000 1350 746 12802 96,1 96,8 96,9 0,80 - 10792 1,1 6,5 2,5 118 7570
1 insulation class H
2 at rated voltage 690 V
19
Weight (IMB3)
rotor current
rotor torque
Breakdown
Moment of
Efficiency
Locked
Locked
current
torque
torque
output
Power
inertia
speed
Rated
Rated
Rated
factor
Type
Item
load
Full
PN nN TN ηN [%] at % of full load cos ϕN IN at rated voltage TL/TN IL/IN Tb/TN J
[kW] [HP] [min-1] [Nm] 50% 75% 100% [-] [A]230V [A]380V [A]400V [-] [-] [-] [kgm2] [kg]
2p=10 ns=600 rpm
170 2Sg 200L10A 7,5 10 580 123 82,5 84 85 0,68 32,5 19,7 18,7 1,7 3,5 2,1 0,4 240
171 2Sg 200L10B 11 15 590 178 84,7 86,7 87,5 0,68 46,5 28,1 26,7 3,2 5,9 2,4 0,47 255
172 2Sg 225S10 13 18 592 210 87,5 89,3 90,5 0,67 54 32,5 31 1,8 3,8 2 0,6 280
173 2Sg 225M10 15 20 590 243 86 88 89 0,67 63 38 36,5 2,8 5,4 2 0,76 315
174 2Sg 225M10z 18,5 25 590 299 84,3 87,1 87,7 0,64 83 50 47,5 2,8 5,5 2,1 0,76 325
175 2Sg 250M10 22 30 592 355 87,5 89,6 90 0,70 88 53 50 3 5,8 2 1,27 430
176 2Sg 280S10A 30 40 586 489 85,3 87,3 88,8 0,71 119 72 69 2 4,5 1,7 1,35 525
177 2Sg 280S10B 37 50 583 606 87 90 91 0,75 136 82 78 1,9 4,5 1,5 1,61 565
178 2Sg 280M10 45 60 587 732 88 90,5 91,6 0,76 162 98 93 2 4,5 1,6 2,03 630
179 2Sg 315S10 45 60 588 731 90 91,5 92,1 0,71 173 105 99 2 4,1 2 2,16 720
180 2Sg 315S10z 55 75 583 901 88 90,5 91,5 0,75 201 122 116 1,7 4,7 1,9 2,86 840
181 2Sg 315M10 75 100 583 1229 88 90,5 91,5 0,75 274 166 158 1,8 4,9 1,5 3,01 895
TECHNICAL DATA
182 Sh 400H10As 200 270 594 3216 94,4 95,1 95,0 0,82 - - 371 1,0 5,4 2,5 25,6 3010
183 Sh 400H10Bs 250 340 594 4019 94,4 95,2 95,2 0,79 - - 480 1,1 5,6 2,6 31,3 3270
184 Sh 450H10As 315 430 594 5064 94,9 95,5 95,5 0,81 - - 3412 1,0 5,9 2,2 49,4 4050
185 Sh 450H10Bs 355 480 594 5708 95,0 95,7 95,7 0,81 - - 3842 1,0 6,0 2,3 53,9 4130
186 Sh 450H10Cs 400 540 594 6431 95,0 95,7 95,7 0,81 - - 4322 1,1 6,4 2,3 58,3 4300
187 Sh 500H10As 450 610 594 7235 95,1 95,8 95,7 0,81 - - 4862 1,4 6,3 2,1 74,1 5420
188 Sh 500H10Bs 500 680 594 8039 95,2 95,9 95,8 0,82 - - 5332 1,5 6,6 2,2 85,5 5700
189 Sh 500H10Cs 560 760 593 9019 95,4 95,9 95,8 0,82 - - 5972 1,3 6,2 2,0 94,2 5950
190 Sh 500H10Ds 630 850 594 10129 95,5 96,0 96,0 0,82 - - 6702 1,7 6,9 2,2 108 6400
2p=12 ns=500 rpm
191 2Sg 200L12 9 12 490 175 75,3 80,1 81,8 0,55 50 30,5 28,9 2,7 4,3 2,5 0,47 255
192 2Sg 225S12 11 15 490 214 83,1 85,0 86,0 0,63 51 31 29,3 1,7 3,5 1,7 0,58 315
193 2Sg 225M12 13 18 475 261 81,5 82,2 82,5 0,59 67 40,5 38,5 1,7 3,5 1,7 0,68 350
194 2Sg 225M12z 15 20 491 292 80,5 83,5 84,4 0,58 77 46,5 44 2,7 4,6 1,8 0,68 350
195 2Sg 250M12 18,5 25 490 361 84,0 86,0 87,8 0,65 81 49,5 47 1,7 3,5 1,8 1,27 430
196 2Sg 280S12 22 30 491 428 86,9 89,2 89,6 0,61 101 61 58 2,3 4,5 1,8 1,47 535
197 2Sg 280M12 30 40 490 585 85,6 88,2 89,0 0,62 136 83 78 1,8 3,5 1,8 1,8 570
198 2Sg 315S12 37 50 492 718 87,5 89,9 90,4 0,58 177 107 102 2,6 4,5 1,9 2,29 730
199 2Sg 315M12A 45 60 490 877 87,9 89,0 90,1 0,58 216 131 124 2 3,5 1,8 2,86 870
200 2Sg 315M12B 55 75 490 1072 87,5 90,0 89,5 0,58 266 161 153 2,5 4,4 1,8 3,01 885
201 Sh 450H12As 160 220 494 3093 94,1 95,0 95,0 0,79 - - 308 0,8 5,6 2,6 30,0 3470
202 Sh 450H12Bs 200 270 495 3859 94,7 94,9 94,9 0,80 - - 381 0,9 5,7 2,3 33,7 3600
203 Sh 450H12Cs 250 340 492 4853 94,7 95,0 94,7 0,82 - - 459 0,8 5,0 2,1 40,0 3750
204 Sh 450H12Ds 315 430 493 6102 94,9 95,2 94,9 0,82 - - 584 0,8 5,1 2,3 45,0 4050
2 - at rated voltage 690 V
As part of our development program the technical specifications indicated may change,
and we reserve the right to alert or to amend any of this specifications without giving prior notice.
In any such instance, you will find any possible change on our web-site: www.cantonigroup.com
20
FOOT MOUNTED MOTORS - IM B3
A-A
F
D
GA
HD
H
A
HA
E C B K AA
BB A
L AB
DIMENSIONAL DRAWINGS
Motor type A B C D E F GA H K AA AB BB HA HD L
Sh 56-.A 90 71 36 9j6 20 3h9 10,2 56 5,8 30 110 92 7 154 183

Sh 56-.B 90 71 36 9j6 20 3h9 10,2 56 5,8 30 110 92 7 154 193
Sh 63-.A 100 80 40 11j6 23 4h9 12,5 63 7 36 124 106 8,5 165 200
Sh 63-.B 100 80 40 11j6 23 4h9 12,5 63 7 36 124 106 8,5 165 210
Sh 71-.A 112 90 45 14j6 30 5h9 16 71 7 45 142 116 8 182 223
Sh 71-.B 112 90 45 14j6 30 5h9 16 71 7 45 142 116 8 182 245
Sh 80-.A 125 100 50 19j6 40 6h9 21,5 80 10 55 160 130 9 200 266
Sh 80-.B 125 100 50 19j6 40 6h9 21,5 80 10 55 160 130 9 200 278
2SIE 80-.A 125 100 50 19j6 40 6h9 21,5 80 10 55 160 130 9 200 266
2SIE 80-.B 125 100 50 19j6 40 6h9 21,5 80 10 55 160 130 9 200 278
2SIE 90S-2,4,6 140 100 56 24j6 50 8h9 27 90 10 41 170 153 10 228 331
2SIE 90L-2 140 125 56 24j6 50 8h9 27 90 10 41 170 153 10 228 331
2SIE 90L-4,6 140 125 56 24j6 50 8h9 27 90 10 41 170 153 10 228 356
2SIE 100L-2,6 160 140 63 28j6 60 8h9 31 100 12 44 197 174 14 250 377
2SIE 100L-4A,4B 160 140 63 28j6 60 8h9 31 100 12 44 197 174 14 250 421
2SIE 112M-2,6 190 140 70 28j6 60 8h9 31 112 12 49 230 174 14 276 389
2SIE 112M-4 190 140 70 28j6 60 8h9 31 112 12 49 230 174 14 276 416
2SIE 132S-2A,6 216 140 89 38k6 80 10h9 41 132 12 62 274 182 17 310 461
2SIE 132S-2B,4 216 140 89 38k6 80 10h9 41 132 12 62 274 182 17 310 499
2SIE 132M-4,6A,6B 216 178 89 38k6 80 10h9 41 132 12 62 274 220 17 310 499
2SIE 160M-2A,2B,4,6 254 210 108 42k6 110 12h9 45 160 15 60 305 256 22 365 611
2SIE 160L-2,4,6 254 254 108 42k6 110 12h9 45 160 15 60 305 300 22 365 655
2SIE 180M-2,4 279 241 121 48k6 110 14h9 51,5 180 15 70 350 315 23 403 701
2SIE 180L-4,6 279 279 121 48k6 110 14h9 51,5 180 15 70 350 315 23 403 701
MOTORS series Sh and Sg 2p=8

Motor type A B C D E F GA H HA K AA AB BB HD L
Sh 90S ... 140 100 56 24j6 50 8h9 27 90 10 10 50 170 153 220 305
Sh 90L ... 140 125 56 24j6 50 8h9 27 90 10 10 50 170 153 220 330
Sg 100L ... 160 140 63 28j6 60 8h9 31 100 14 12 45 200 172 240 376
Sg 112M ... 190 140 70 28j6 60 8h9 31 112 14 12 54 230 174 276 384
Sg 132S ... 216 140 89 38k6 80 10h9 41 132 16 12 56 278 182 310 463
Sg 132S-2B 216 140 89 38k6 80 10h9 41 132 16 12 56 278 220 310 501
Sg 132M ... 216 178 89 38k6 80 10h9 41 132 16 12 56 278 220 310 501
Sg 160M ... 254 210 108 42k6 110 12h9 45 160 20 15 60 305 256 370 612
Sg 160L ... 254 254 108 42k6 110 12h9 45 160 20 15 60 305 300 370 656
Sg 180M ... 279 241 121 48k6 110 14h9 51,5 180 26 15 70 350 320 408 705
Sg 180L ... 279 279 121 48k6 110 14h9 51,5 180 26 15 70 350 320 408 705
21
HD
A
H
HA
A-A
D
BA1 BA2 AA K
F
GA E C B A
B1 AB
BB
L
Motor type A B B1 C D E F GA H HA K AA AB BA1 BA2 BB HD L
2SIE200 318 305 - 133 55 110 16 59 200 32 19 80 400 113 113 380 520 850
2SIE225S4 356 286 311 149 60 140 18 64 225 34 19 85 440 115 115 380 570 930
2SIE225M2 356 286 311 149 55 110 16 59 225 34 19 85 440 115 115 380 570 900
2SIE225M4-6 356 286 311 149 60 140 18 64 225 34 19 85 440 115 115 380 570 930
2SIE250M2 406 349 - 168 60 140 18 64 250 37 24 90 480 135 135 445 635 1010
2SIE250M4-6 406 349 - 168 65 140 18 69 250 37 24 90 480 135 135 445 635 1040
2SIE280S2 457 368 419 190 65 140 18 69 280 40 24 105 550 130 165 520 720 1135
2SIE280S4-6 457 368 419 190 75 140 20 79,5 280 40 24 105 550 130 165 520 720 1135
2SIE280M2 457 368 419 190 65 140 18 69 280 40 24 105 550 130 165 520 720 1135
2SIE280M4-6 457 368 419 190 75 140 20 79,5 280 40 24 105 550 130 165 520 720 1135
2SIE315S2 508 406 457 216 65 140 18 69 315 48 28 120 610 160 160 565 805 1235
2SIE315S4-6 508 406 457 216 80 170 22 85 315 48 28 120 610 160 160 565 805 1265
2SIE315M2A;B 508 406 457 216 65 140 18 69 315 48 28 120 610 160 160 565 805 1235
2SIE315M4A;B;6A 508 406 457 216 80 170 22 85 315 48 28 120 610 160 160 565 805 1265
2SIE315M6B 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 1355
2SIE315M2C 508 406 457 216 70 140 20 74,5 315 48 28 135 610 135 205 600 805 1290
2SIE315M4C 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 1320
2SIE315M6C 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 1320
2SIE315M6D 508 406 457 216 90 170 25 95 315 48 28 135 610 135 205 600 805 1320
2SIE 315 ML (4, 6) 508 457 508 216 80 170 22 85 315 40 28 120 620 150 180 637 865 1345
2SIE 355 ML (2) 610 560 630 254 80 170 22 85 355 50 28 150 720 250 300 890 935 1580
2SIE 355 ML (4, 6) 610 560 630 254 100 210 28 106 355 50 28 150 720 250 300 890 935 1620
2SIE 355 H (2) 610 900 - 200 70 140 20 74.5 355 45 28 160 730 265 265 1045 995 1800
2SIE 355 H (4, 6) 610 900 - 200 100 210 28 106 355 45 28 160 730 265 265 1045 995 1870
SEE 355 ML8 610 560 630 254 100 210 28 106 355 50 28 150 720 250 300 890 935 1620
22
A-A
AC
F
D
GA
HD
A
HA
H
BA AA K
E C B A
BB AB
L
Motor type A B C D E F GA H HA K AA AB AC BA BB HD L
2Sg 200 L8-12 318 305 133 55m6 110 16h9 59 200 32 19 80 400 450 100 380 485 825
2Sg 225 S8-12 356 286 149 60m6 140 18h9 64 225 34 19 85 445 505 110 355 535 865
2Sg 225 M8-12 356 311 149 60m6 140 18h9 64 225 34 19 85 445 505 110 380 535 890
2Sg 250 M8-12 406 349 168 65m6 140 18h9 69 250 36 24 90 495 540 120 420 590 965
2Sg 280 S8-12 457 368 190 75m6 140 20h9 79,5 280 40 24 100 560 620 165 520 660 1040
2Sg 280 M8-12 457 419 190 75m6 140 20h9 79,5 280 40 24 100 560 620 165 520 660 1040
2Sg 315 S8-12 508 406 216 80m6 170 22h9 85 315 46 28 105 610 620 190 560 695 1210
2Sg 315 M8-12 508 457 216 80m6 170 22h9 85 315 46 28 105 610 620 190 560 695 1210
AD
A-A
HD
A
D
GA A
H
HA
BA BA AA K
E C B A
BB AB
L
Motor type Poles

A B C D E F GA H HA K AA AB AD BA BB HD L
Sh 355...s 2 610 900 200 70 140 20 74,5 355 45 28 160 730 - 265 1045 995 1800
Sh 355...s 4÷8 610 900 200 100 210 28 106 355 45 28 160 730 - 265 1045 995 1870
Sh 400...s 2 686 1000 224 80 170 22 85 400 50 35 175 840 520 265 1160 1255 1980
Sh 400...s 4÷8 686 1000 224 110 210 28 116 400 50 35 175 840 520 265 1160 1255 1960
Sh 450...s 4÷12 750 1120 254 110 210 28 116 450 60 35 205 940 560 340 1320 1356 2105
Sh 500...s 4÷10 850 1250 280 120 210 32 127 500 70 42 223 1050 560 300 1450 1470 2430
23
FLANGE MOUNTED MOTORS - IM B5, IM V1
T LA
HB
A-A A
R=O M
F
D
N
P
GA A S
45
°
E
L 22,5° 45°
Motor type D E F GA M N P LA T HB L S (φ) S (holes)
SKh 56-.A 9j6 20 3h9 10,2 100 80j6 120 8 3 98 183 7 4

SKh 56-.B 9j6 20 3h9 10,2 100 80j6 120 8 3 98 193 7 4
SKh 63-.A 11j6 23 4h9 12,5 115 95j6 140 9 3 102 200 10 4
SKh 63-.B 11j6 23 4h9 12,5 115 95j6 140 9 3 102 210 10 4
SKh 71-.A 14j6 30 5h9 16 130 110j6 160 9 3,5 111 223 10 4
SKh 71-.B 14j6 30 5h9 16 130 110j6 160 9 3,5 111 245 10 4
SKh 80-.A 19j6 40 6h9 21,5 165 130j6 200 10 3,5 120 266 12 4
SKh 80-.B 19j6 40 6h9 21,5 165 130j6 200 10 3,5 120 278 12 4
2SIEK 80-.A 19j6 40 6h9 21,5 165 130j6 200 10 3,5 120 266 12 4
2SIEK 80-.B 19j6 40 6h9 21,5 165 130j6 200 10 3,5 120 278 12 4
2SIEK 90S-2,4,6 24j6 50 8h9 27 165 130j6 200 8 3,5 139 331 12 4
2SIEK 90L-2 24j6 50 8h9 27 165 130j6 200 8 3,5 139 331 12 4
2SIEK 90L-4,6 24j6 50 8h9 27 165 130j6 200 8 3,5 139 356 12 4
2SIEK 100L-2,6 28j6 60 8h9 31 215 180j6 250 11 4 150 377 15 4
2SIEK 100L-4A,4B 28j6 60 8h9 31 215 180j6 250 11 4 150 421 15 4
2SIEK 112M-2,6 28j6 60 8h9 31 215 180j6 250 12 4 165 385 15 4
2SIEK 112M-4 28j6 60 8h9 31 215 180j6 250 12 4 165 416 15 4
2SIEK 132S-2A,6 38k6 80 10h9 41 265 230j6 300 12 4 178 461 15 4
2SIEK 132S-2B,4 38k6 80 10h9 41 265 230j6 300 12 4 178 499 15 4
2SIEK 132M-4,6A,6B 38k6 80 10h9 41 265 230j6 300 12 4 178 499 15 4
2SIEK 160M-2A,2B,4,6 42k6 110 12h9 45 300 250j6 350 13 5 205 611 19 4
2SIEK 160L-2,4,6 42k6 110 12h9 45 300 250j6 350 13 5 205 655 19 4
2SIEK 180M-2,4 48k6 110 14h9 51,5 300 250j6 350 13 5 224 701 19 4
2SIEK 180L-4,6 48k6 110 14h9 51,5 300 250j6 350 13 5 224 701 19 4
2SIEK 200 55 110 16 59 350 300 400 16,5 5 320 850 19 4
2SIEK 225S4 60 140 18 64 400 350 450 18 5 345 930 19 8
2SIEK 225M2 55 110 16 59 400 350 450 18 5 345 900 19 8
2SIEK 225M4-6 60 140 18 64 400 350 450 18 5 345 930 19 8
2SIEK 250M2 60 140 18 64 500 450 550 23 5 385 1010 19 8
2SIEK 250M4-6 65 140 18 69 500 450 550 23 5 385 1040 19 8
2SIEK 280S2 65 140 18 69 500 450 550 23 5 440 1135 19 8
2SIEK 280S4-6 75 140 20 79,5 500 450 550 23 5 440 1135 19 8
2SIEK 280M2 65 140 18 69 500 450 550 23 5 440 1135 19 8
2SIEK 280M4-6 75 140 20 79,5 500 450 550 23 5 440 1135 19 8
2SIEK 315S2 65 140 18 69 600 550 660 23 6 490 1235 24 8
2SIEK 315S4-6 80 170 22 85 600 550 660 23 6 490 1265 24 8
2SIEK 315M2A;B 65 140 18 69 600 550 660 23 6 490 1235 24 8
2SIEK 315M4A;B;6A 80 170 22 85 600 550 660 23 6 490 1265 24 8
2SIEK 315M6B* 80 170 22 85 600 550 660 23 6 490 1355 24 8
2SIEK 315M2C* 70 140 20 74,5 600 550 660 23 6 490 1290 24 8
2SIEK 315M4C* 80 170 22 85 600 550 660 23 6 490 1320 24 8
2SIEK 315M6C* 80 170 22 85 600 550 660 23 6 490 1320 24 8
2SIEK 315M6D* 90 170 25 95 600 550 660 23 6 490 1320 24 8
2SIEK 355 ML (4 - 6)* 100m6 210 28h9 106 740 680 800 24 6 580 1620 22 8
2SIEK 355 H (4 - 6)* 100m6 210 28h9 106 740 680 800 24 6 638 1955 22 8
SVEE 355ML8* 100 210 28 106 740 680 800 24 6 580 1620 22 8
* only in vertical position IM V1
24
Type of motor D E F GA M N P LA T S HB L
SKh 90S ... 24j6 50 8h9 27 165 130j6 200 8 3,5 12 130 305
SKh 90L ... 24j6 50 8h9 27 165 130j6 200 8 3,5 12 130 330
SKg 100L ... 28j6 60 8h9 31 215 180j6 250 11 4 15 140 376
SKg 112M ... 28j6 60 8h9 31 215 180j6 250 12 4 15 164 384
SKg 132S ... 38k6 80 10h9 41 265 230j6 300 12 4 15 178 463
SKg 132S-2B 38k6 80 10h9 41 265 230j6 300 12 4 15 178 501
SKg 132M ... 38k6 80 10h9 41 265 230j6 300 12 4 15 178 501
SKg 160M ... 42k6 110 12h9 45 300 250j6 350 13 5 19 210 612
SKg 160L ... 42k6 110 12h9 45 300 250j6 350 13 5 19 210 656
SKg 180M ... 48k6 110 14h9 51,5 300 250j6 350 13 5 19 228 705
SKg 180L ... 48k6 110 14h9 51,5 300 250j6 350 13 5 19 228 705
AC
AD
T LA
S
A-A
A M
F
P
D
R=O
GA
A
45
°
22,5° 45°
E
Motor type D E F GA AC AD L LA M N P T S
Holes
2SKg 200 L8-12 55m6 110 16h9 59 450 340 825 16,5 350 300j6 400 5 18 4
2SKg 225 S8-12 60m6 140 18h9 64 505 360 865 18 400 350j6 450 5 18 8
2SKg 225 M8-12 60m6 140 18h9 64 505 360 890 18 400 350j6 450 5 18 8
2SKg 250 M8-12 65m6 140 18h9 69 540 405 965 19 500 450j6 550 5 18 8
2SKg 280 S8-12 75m6 140 20h9 79,5 620 440 1040 20 500 450j6 550 5 18 8
2SKg 280 M8-12 75m6 140 20h9 79,5 620 440 1040 20 500 450j6 550 5 18 8
2SKg 315 S8-12 80m6 170 22h9 85 620 440 1210 22 600 550j6 660 6 22 8
2SKg 315 M8-12 80m6 170 22h9 85 620 440 1210 22 600 550j6 660 6 22 8
25
SVh
A-A
F
GA
HB
M
LA
A R=0
T
E
A
S
N
P
Motor type Poles D E F GA HB L LA M N P S T

SVh 355...s* 4÷8 100 210 28 106 640 1955 24 740 680 800 22 6
SVh 400...s* 4÷8 110 210 28 116 725 2016 37 940 880 1000 23 6
SVh 450...s* 4÷12 110 210 28 116 835 2162 30 1080 1000 1150 28 6
SVh 500...s* 4÷12 120 210 32 127 835 2505 30 1080 1000 1150 28 6
* - the SVh motors may operate only in vertical position IM V1.
FOOT/FLANGE MOUNTED MOTORS - IM B35

45°
T LA
S
A-A
A
R=O M
F
HD
4x90°
D
N
P
GA A
HA
H
E C B K AA
BB A
L AB
Motor type A B C D E F GA H K M N P S LA T AA AB BB HA HD L
SLh 56-.A 90 71 36 9j6 20 3h9 10,2 56 8 100 80j6 120 7 8 3 30 110 92 7 154 183
SLh 56-.B 90 71 36 9j6 20 3h9 10,2 56 8 100 80j6 120 7 8 3 30 110 92 7 154 193
SLh 63-.A 100 80 40 11j6 23 4h9 12,5 63 10 115 95j6 140 10 9 3 36 124 106 8,5 165 200
SLh 63-.B 100 80 40 11j6 23 4h9 12,5 63 10 115 95j6 140 10 9 3 36 124 106 8,5 165 210
SLh 71-.A 112 90 45 14j6 30 5h9 16 71 10 130 110j6 160 10 9 3,5 45 142 116 8 182 223
SLh 71-.B 112 90 45 14j6 30 5h9 16 71 10 130 110j6 160 10 9 3,5 45 142 116 8 182 245
SLh 80-.A 125 100 50 19j6 40 6h9 21,5 80 10 165 130j6 200 12 10 3,5 55 160 130 9 200 266
SLh 80-.B 125 100 50 19j6 40 6h9 21,5 80 10 165 130j6 200 12 10 3,5 55 160 130 9 200 278
2SIEL 80-.A 125 100 50 19j6 40 6h9 21,5 80 10 165 130j6 200 12 10 3,5 55 160 130 9 200 266
2SIEL 80-.B 125 100 50 19j6 40 6h9 21,5 80 10 165 130j6 200 12 10 3,5 55 160 130 9 200 278
2SIEL 90S-2,4,6 140 100 56 24j6 50 8h9 27 90 10 165 130j6 200 12 8 3,5 41 170 153 10 228 331
2SIEL 90L-2 140 125 56 24j6 50 8h9 27 90 10 165 130j6 200 12 8 3,5 41 170 153 10 228 331
2SIEL 90L-4,6 140 125 56 24j6 50 8h9 27 90 10 165 130j6 200 12 8 3,5 41 170 153 10 228 356
2SIEL 100L-2,6 160 140 63 28j6 60 8h9 31 100 12 215 180j6 250 15 11 4 44 197 174 14 250 377
2SIEL 100L-4A,4B 160 140 63 28j6 60 8h9 31 100 12 215 180j6 250 15 11 4 44 197 174 14 250 421
2SIEL 112M-2,6 190 140 70 28j6 60 8h9 31 112 12 215 180j6 250 15 12 4 49 230 174 14 276 389
2SIEL 112M-4 190 140 70 28j6 60 8h9 31 112 12 215 180j6 250 15 12 4 49 230 174 14 276 416
2SIEL 132S-2A,6 216 140 89 38k6 80 10h9 41 132 12 265 230j6 300 15 12 4 62 274 182 17 310 461
2SIEL 132S-2B,4 216 140 89 38k6 80 10h9 41 132 12 265 230j6 300 15 12 4 62 274 182 17 310 499
2SIEL 132M-4,6A,6B 216 178 89 38k6 80 10h9 41 132 12 265 230j6 300 15 12 4 62 274 220 17 310 499
2SIEL 160M-2A,2B,4,6 254 210 108 42k6 110 12h9 45 160 15 300 250j6 350 19 13 5 60 305 256 22 370 611
2SIEL 160L-2,4,6 254 254 108 42k6 110 12h9 45 160 15 300 250j6 350 19 13 5 60 305 300 22 370 655
2SIEL 180M-2,4 279 241 121 48k6 110 14h9 51,5 180 15 300 250j6 350 19 13 5 70 350 315 23 408 701
2SIEL 180L-4,6 279 279 121 48k6 110 14h9 51,5 180 15 300 250j6 350 19 13 5 70 350 315 23 408 701
26
Motor type A B C D E F GA H HA K AA AB BB HD L LA M N P T S
SLh 90S ... 140 100 56 24j6 50 8h9 27 90 10 10 50 170 153 220 305 8 165 130j6 200 3,5 12
SLh 90L ... 140 125 56 24j6 50 8h9 27 90 10 10 50 170 153 220 330 8 165 130j6 200 3,5 12
SLg 100L ... 160 140 63 28j6 60 8h9 31 100 14 12 45 200 172 240 376 11 215 180j6 250 4 15
SLg 112M ... 190 140 70 28j6 60 8h9 31 112 14 12 54 230 174 276 384 12 215 180j6 250 4 15
SLg 132S ... 216 140 89 38k6 80 10h9 41 132 16 12 56 278 182 310 463 12 265 230j6 300 4 15
SLg 132S-2B 216 140 89 38k6 80 10h9 41 132 16 12 56 278 220 310 501 12 265 230j6 300 4 15
SLg 132M ... 216 178 89 38k6 80 10h9 41 132 16 12 56 278 220 310 501 12 265 230j6 300 4 15
SLg 160M ... 254 210 108 42k6 110 12h9 45 160 20 15 60 305 256 370 612 13 300 250j6 350 5 19
SLg 160L ... 254 254 108 42k6 110 12h9 45 160 20 15 60 305 300 370 656 13 300 250j6 350 5 19
SLg 180M ... 279 241 121 48k6 110 14h9 51,5 180 26 15 70 350 320 408 705 13 300 250j6 350 5 19
SLg 180L ... 279 279 121 48k6 110 14h9 51,5 180 26 15 70 350 320 408 705 13 300 250j6 350 5 19
T LA
A-A M
HD
A R=0
N
P
D
GA A 45
°
H
45°
HA
22,5°
BA1 BA2 AA K
E C B A
B1 AB
BB
L
Motor type A B B1 C D E F GA H HA K AA AB BA1 BA2 BB HD LA P M N T L S (φ) S (holes)
2SIEL 200 318 305 - 133 55 110 16 59 200 32 19 80 400 113 113 380 520 16,5 400 350 300 5 850 19 4
2SIEL 225S4 356 286 311 149 60 140 18 64 225 34 19 85 440 115 115 380 570 18 450 400 350 5 930 19 8
2SIEL 225M2 356 286 311 149 55 110 16 59 225 34 19 85 440 115 115 380 570 18 450 400 350 5 900 19 8
2SIEL 225M4-6 356 286 311 149 60 140 18 64 225 34 19 85 440 115 115 380 570 18 450 400 350 5 930 19 8
2SIEL 250M2 406 349 - 168 60 140 18 64 250 37 24 90 480 135 135 445 635 23 550 500 450 5 1010 19 8
2SIEL 250M4-6 406 349 - 168 65 140 18 69 250 37 24 90 480 135 135 445 635 23 550 500 450 5 1040 19 8
2SIEL 280S2 457 368 419 190 65 140 18 69 280 40 24 105 550 130 165 520 720 23 550 500 450 5 1135 19 8
2SIEL 280S4-6 457 368 419 190 75 140 20 79,5 280 40 24 105 550 130 165 520 720 23 550 500 450 5 1135 19 8
2SIEL 280M2 457 368 419 190 65 140 18 69 280 40 24 105 550 130 165 520 720 23 550 500 450 5 1135 19 8
2SIEL 280M4-6 457 368 419 190 75 140 20 79,5 280 40 24 105 550 130 165 520 720 23 550 500 450 5 1135 19 8
2SIEL 315S2 508 406 457 216 65 140 18 69 315 48 28 120 610 160 160 565 805 23 660 600 550 6 1235 24 8
2SIEL 315S4-6 508 406 457 216 80 170 22 85 315 48 28 120 610 160 160 565 805 23 660 600 550 6 1265 24 8
2SIEL 315M2A;B 508 406 457 216 65 140 18 69 315 48 28 120 610 160 160 565 805 23 660 600 550 6 1235 24 8
2SIEL 315M4A;B;6A 508 406 457 216 80 170 22 85 315 48 28 120 610 160 160 565 805 23 660 600 550 6 1265 24 8
2SIEL 315M6B 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 23 660 600 550 6 1355 24 8
2SIEL 315M2C 508 406 457 216 70 140 20 74,5 315 48 28 135 610 135 205 600 805 23 660 600 550 6 1290 24 8
2SIEL 315M4C 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 23 660 600 550 6 1320 24 8
2SIEL 315M6C 508 406 457 216 80 170 22 85 315 48 28 135 610 135 205 600 805 23 660 600 550 6 1320 24 8
2SIEL 315M6D;8C;8D 508 406 457 216 90 170 25 95 315 48 28 135 610 135 205 600 805 23 660 600 550 6 1320 24 8
2SIEL 315 ML (4,6) 508 457 508 216 80 170 22 85 315 40 28 120 620 150 180 637 865 22 660 600 550 6 1345 22 8
2SIEL 355 ML (2) 610 560 630 254 80 170 22 85 355 50 28 150 720 250 300 890 935 24 800 740 680 6 1580 22 8
2SIEL 355 ML (4,6) 610 560 630 254 100 210 28 106 355 50 28 150 720 250 300 890 935 24 800 740 680 6 1620 22 8
2SIEL 355 H (2) 610 900 - 254 70 140 20 74.5 355 45 28 160 730 265 265 1045 995 24 800 740 680 6 1854 22 8
2SIEL 355 H (4,6) 610 900 - 254 100 210 28 106 355 45 28 160 730 265 265 1045 995 24 800 740 680 6 1924 22 8
SLEE 355 ML8 610 560 630 254 100 210 28 106 355 50 28 150 720 250 300 890 935 24 800 740 680 6 1620 22 8
27
A-A
F
D
AC
GA
T LA
S
M
A
P
N
HD
R=O 45
°
HA
H
A 22,5° 45°
BA AA K
E C B A
BB AB
L
Motor type A B C D E F GA H HA K AA AB AC BA BB HD L LA M N P T S
Holes
2SLg 200 L8-12 318 305 133 55m6 110 16h9 59 200 32 19 80 400 450 100 380 485 825 16,5 350 300 400 5 18 4
2SLg 225 S8-12 356 286 149 60m6 140 18h9 64 225 34 19 85 445 505 110 355 535 865 18 400 350 450 5 18 8
2SLg 225 M8-12 356 311 149 60m6 140 18h9 64 225 34 19 85 445 505 110 380 535 890 18 400 350 450 5 18 8
2SLg 250 M8-12 406 349 168 65m6 140 18h9 69 250 36 24 90 495 540 120 420 590 965 19 500 450 550 5 18 8
2SLg 280 S8-12 457 368 190 75m6 140 20h9 79,5 280 40 24 100 560 620 165 520 660 1040 20 500 450 550 5 18 8
2SLg 280 M8-12 457 419 190 75m6 140 20h9 79,5 280 40 24 100 560 620 165 520 660 1040 20 500 450 550 5 18 8
2SLg 315 S8-12 508 406 216 80m6 170 22h9 85 315 46 28 105 610 620 190 560 695 1210 22 600 550 660 6 22 8
2SLg 315 M8-12 508 457 216 80m6 170 22h9 85 315 46 28 105 610 620 190 560 695 1210 22 600 550 660 6 22 8
A-A AD
D
T LA GA
HD
S
A R=0
M
N
P
A
H
HA
BA BA AA K
E C B A
BB AB
L
Type of Poles
motor A B C D E F GA H HA K AA AB AD BA BB HD L LA M N P S T
SLh 355...s 2 610 900 254 70 140 20 74.5 355 45 28 160 730 344 265 1045 995 1854 24 740 680 800 22 6
SLh 355...s 4÷8 610 900 254 100 210 28 106 355 45 28 160 730 344 265 1045 995 1924 24 740 680 800 22 6
SLh 400...s 2 686 1000 280 80 170 22 85 400 50 35 175 840 520 265 1160 1255 2031 30 940 880 1000 25 6
SLh 400...s 4÷8 686 1000 280 110 210 28 116 400 50 35 175 840 520 265 1160 1255 2016 30 940 880 1000 25 6
SLh 450...s 4÷12 750 1120 315 110 210 28 116 450 60 35 205 940 560 340 1320 1356 2162 30 1080 1000 1150 28 6
SLh 500...s 4÷10 850 1250 355 120 210 32 127 500 70 42 223 1050 560 300 1450 1470 2505 30 1080 1000 1150 28 6
28
FLANGE MOUNTED MOTORS - IM B14
45°
T LE
HB
A
A-A
4x90°
R=O
F
M
N
P
D
GA
A
E
S
L
Motor type Flange D E F GA M N P S T LE HB L
SKh 56- .A1 B14/C1 9j6 20 3h9 10,2 85 70j6 105 M6 2,5 15 98 183
SKh 56- .A2 B14/C2 9j6 20 3h9 10,2 65 50j6 80 M5 2,5 12,5 98 183
SKh 56- .B1 B14/C1 9j6 20 3h9 10,2 85 70j6 105 M6 2,5 15 98 193
SKh 56- .B2 B14/C2 9j6 20 3h9 10,2 65 50j6 80 M5 2,5 12,5 98 193
SKh 63- .A1 B14/C1 11j6 23 4h9 12,5 100 80j6 120 M6 3 14 102 200
SKh 63- .A2 B14/C2 11j6 23 4h9 12,5 75 60j6 90 M5 2,5 9,5 102 200
SKh 63- .B1 B14/C1 11j6 23 4h9 12,5 100 80j6 120 M6 3 14 102 210
SKh 63- .B2 B14/C2 11j6 23 4h9 12,5 75 60j6 90 M5 2,5 9,5 102 210
SKh 71- .A1 B14/C1 14j6 30 5h9 16 115 95j6 140 M8 3 14 111 223
SKh 71- .A2 B14/C2 14j6 30 5h9 16 85 70j6 105 M6 2,5 12 111 223
SKh 71- .B1 B14/C1 14j6 30 5h9 16 115 95j6 140 M8 3 14 111 245
SKh 71- .B2 B14/C2 14j6 30 5h9 16 85 70j6 105 M6 2,5 12 111 245
SKh 80- .A1 B14/C1 19j6 40 6h9 21,5 130 110j6 160 M8 3,5 14 120 266
SKh 80- .A2 B14/C2 19j6 40 6h9 21,5 100 80j6 120 M6 3 12 120 266
SKh 80- .B1 B14/C1 19j6 40 6h9 21,5 130 110j6 160 M8 3,5 14 120 278
SKh 80- .B2 B14/C2 19j6 40 6h9 21,5 100 80j6 120 M6 3 12 120 278
2SIEK 80- .A1 B14/C1 19j6 40 6h9 21,5 130 110j6 160 M8 3,5 14 120 266
2SIEK 80- .A2 B14/C2 19j6 40 6h9 21,5 100 80j6 120 M6 3 12 120 266
2SIEK 80- .B1 B14/C1 19j6 40 6h9 21,5 130 110j6 160 M8 3,5 14 120 278
2SIEK 80- .B2 B14/C2 19j6 40 6h9 21,5 100 80j6 120 M6 3 12 120 278
2SIEK 90S 2,4,6 B14/C1 24j6 50 8h9 27 130 110j6 160 M8 3,5 10 139 331
2SIEK 90S 2,4,6 B14/C2 24j6 50 8h9 27 115 95j6 140 M8 3 10 139 331
2SIEK 90L 2 B14/C1 24j6 50 8h9 27 130 110j6 160 M8 3,5 10 139 331
2SIEK 90L 2 B14/C2 24j6 50 8h9 27 115 95j6 140 M8 3 10 139 331
2SIEK 90L 4,6 B14/C1 24j6 50 8h9 27 130 110j6 160 M8 3,5 10 139 356
2SIEK 90L 4,6 B14/C2 24j6 50 8h9 27 115 95j6 140 M8 3 10 139 356
2SIEK 100L2,6 B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 150 377
2SIEK 100L2,6 B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 150 377
2SIEK 100L4A,4B B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 150 421
2SIEK 100L4A,4B B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 150 421
2SIEK 112M2,6 B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 165 389
2SIEK 112M2,6 B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 165 389
2SIEK 112M4 B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 165 416
2SIEK 112M4 B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 165 416
2SIEK 132S2A,6 B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 461
2SIEK 132S2A,6 B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 461
2SIEK 132S2B,4 B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 499
2SIEK 132S2B,4 B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 499
2SIEK 132M4,6A,6B B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 499
2SIEK 132M4,6A,6B B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 499
29
FLANGE MOUNTED MOTORS - IM B14
45°
T LE
HB
A
A-A
4x90°
R=O
F
M
N
P
D
GA
A
E
S
L
Motor type Flange D E F GA M N P S T LE HB L
SKh 90S ... B14/C2 24j6 50 8h9 27 115 95j6 140 M8 3 10 130 305
SKh 90L ... B14/C1 24j6 50 8h9 27 130 110j6 160 M8 3,5 10 130 330
SKh 90L ... B14/C2 24j6 50 8h9 27 115 95j6 140 M8 3 10 130 330
SKg 100L ... B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 140 376
SKg 100L ... B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 140 376
SKg 112M ... B14/C1 28j6 60 8h9 31 165 130j6 200 M10 3,5 12 164 384
SKg 112M ... B14/C2 28j6 60 8h9 31 130 110j6 160 M8 3,5 12 164 384
SKg 132S ... B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 463
SKg 132S ... B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 463
SKg 132S-2B B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 501
SKg 132S-2B B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 501
SKg 132M ... B14/C1 38k6 80 10h9 41 215 180j6 250 M12 4 12 178 501
SKg 132M ... B14/C2 38k6 80 10h9 41 165 130j6 200 M10 3,5 12 178 501
SKg 160M ... B14/C1 42k6 110 12h9 45 265 230j6 300 M12 4 13 210 612
SKg 160M... B14/C2 42k6 110 12h9 45 215 180j6 250 M12 4 20 210 612
SKg 160L ... B14/C1 42k6 110 12h9 45 265 230j6 300 M12 4 13 210 656
SKg 160L ... B14/C2 42k6 110 12h9 45 215 180j6 250 M12 4 20 210 656
30
Frame Size: 56-80
Motor series 2SIE and Sh
3
7
4
22 6 8
LIST OF MOTOR PARTS

5 9
21
12 10
11
14
23 Item Description
20 15 1 terminal box cover
2 rubber gasket
3 terminal board
4 terminal box
19 5 rubber gasket
6 gland
16 13 7 terminal box complete
8 fan cover
9 fan
15 10 tie rod
11 NDE shield
12 stator
13 foot
18 17 14 spring washer
15 bearing
16 rotor
17 DE shield
18 shaft seal
19 key
20 flange B5
21 flange B14/C1
22 flange B14/C2
23 name plate
DE - drive end
NDE - non drive end
31
Frame Size: 90÷180
Motor series 2SIE
15
13
17
25
18
20
19
16 4
14
24 12
LIST OF MOTOR PARTS
11
3
22
5 10
23 2
6 7
Item Description
1 DE shield
2 rotor
3 shaft seal
8 4 shaft seal cover
9 5 bearing
5
6 key
3 21 7 name plate
81 sx foot
91 dx foot
1 10 NDE shield
4 11 fan
12 seeger ring
13 fan cover
14 rubber gasket
15 terminal box cover
16 terminal board
17 rubber gasket
18 terminal box
19 glands
20 terminal box complete
21 spring washer
22 stator
232 flange B14/C2
242 flange B14/C1
25 flange B5
1 - for frame size 132 feet can be
DE - drive end screwed or integrated with

NDE - non drive end the motor housing, for frame size
160 -180 feet are integrated with
the motor housing.
2 - only for frame size 90 - 132.
32
Frame Size: 200÷355
Motor series 2SIE
13
12
15 11
10
25 14 24b 21b
24a 16
4b 9
17
18
26
3b
LIST OF MOTOR PARTS

8b
22b
7a 19
4a 7b 23b
20
24a
6
2
Item Description
5 1 DE shield
2 rotor
3a,b shaft seal
22a 23a 4a,b bearing
5 key
6 housing with feet
1
7a,b internal bearing cap
3a 8a 8a,b external bearing cap
9 NDE shield
10 fan
21a
11 seeger ring
12 fan cover
14 terminal board
15 rubber gasket
16 terminal box housing
17 rubber gasket
18 cable glands
19 fan cover support
20 spring washer
21a,b seeger ring
22a,b grease shield
23a,b bearing internal ring
24a,b grease nipple
25 flange B5
26 rubber gasket
DE - drive end
NDE - non drive end
33
Frame Size: 200÷315
Motor series 2Sg
12
11
10
22
26
13
9
6
7
2 3
5
7 8b
25
LIST OF MOTOR PARTS
23
1
4 24
23
8a 20
22 14
16
19
25 17
18
Item Description
27 15 1 DE shield
2 rotor
3 shaft seal
4 DE bearing
5 key
6 housing with feet
3 24 7 internal bearing cap
8a,b external bearing cap
21 9 NDE shield
10 fan
11 seeger ring
12 fan cover
13 NDE bearing
15 terminal cover support
16 rubber gasket
17 terminal box housing
18 rubber gasket
19 cable glands
20 fan cover support
21 spring washer
22 seeger ring
23 grease shield *
24 bearing internal ring *
25 DE grease nipple
26 NDE grease nipple
27 flange B5
* only for size 315

DE - drive end
NDE - non drive end
34
PRODUCTION PROGRAM
GENERAL PURPOSE 3-PHASE INDUCTION MOTORS MULTI-SPEED MOTORS

General purpose 2-speed motors motors
GENERAL PURPOSE 1-PHASE INDUCTION MOTORS General purpose multi-speed motors
HIGH VOLTAGE INDUCTION MOTORS MARINE MOTORS

Totally enclosed motors IP55 General purpose marine motors
Totally enclosed motors for power engineering IP55 Marine motors for pumps
Open drip proof motors IP23 Marine motors for axial-flow fans
Marine motors for boat davits
MOTORS WITH INCREASED RATED OUTPUT Marine motors for tubular rudders
General purpose explosion-proof marine motors
MOTORS WITH FOREIGN COOLING Explosion-proof marine motors for pumps
Motors with foreign cooling IP54 (IP55) Explosion-proof marine motors for axial-flow fans
PRODUCTION PROGRAM
Motors with foreign cooling IP20
3-PHASE INDUCTION MOTORS FOR PUMPS SLIP RING INDUCTION MOTORS

Standard motors for pumps Totally enclosed (IP 54, 55) wound rotor induction motors
Explosion-proof motors for pumps Open drip proof (IP 23) wound rotor induction motors
Explosion-proof marine motors for pumps
MOTORS TO BE BUILT-IN CRANE MOTORS

1-phase motors to be built-in Squirrel cage crane motors
3-phase motors to be built-in Slip ring rotor crane motors
Two-speed crane motors with brake
BRAKE MOTORS
Brake motors (with DC brake)
Brake motors (with AC brake) SPECIAL PURPOSE INDUCTION MOTORS
Motors with increased slip
EXPLOSION-PROOF MOTORS Roller table motors for iron and steel industry
Increased safety motors 1-phase motors with shaft height 65 mm
Flame-proof motors 3-phase motors with shaft height 65 mm
Flame-proof marine motors
Special purpose flame-proof motors for mining
Special purpose flame-proof motors for chemical industry MOTORS ACCORDING TO EPACT AND PREMIUM REQUIREMENTS
Special purpose flame-proof marine motors
High voltage flame-proof motors
MOTORS FOR AXIAL-FLOW FANS ACCESSORIES

1-phase motors for axial-flow fans DC electromagnetic disc brakes
3-phase motors for axial-flow fans AC electromagnetic disc brakes
3-phase motors for axial-flow mining fans Powder brakes and clutches
3-phase explosion-proof motors for air duct axial-flow fans Thrustors
3-phase marine motors for axial-flow fans
3-phase explosion-proof marine motors for axial-flow fans
3-phase multi-speed motors for axial-flow fans
3-phase multi-speed motors for air duct axial-flow fans
35
CANTONI MOTOR S.A.
3 Maja 28th Street
43-400 Cieszyn, Poland
SIE_3FAZ_EN/VER_B
tel.: +48 33 813 87 00

fax: +48 33 813 87 01
motor@cantonigroup.com
www.cantonimotor.com

General Purpose 3-Phase Induction Motors: Product Catalogue

Uploaded by

Copyright:

Available Formats

General Purpose 3-Phase Induction Motors: Product Catalogue

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

General Purpose 3-Phase Induction Motors: Product Catalogue

Uploaded by

Copyright:

Available Formats

General Purpose

Comply with the new efficiency classes

IEC 60034-30 standard and EU Regulation 640/2009

CANTONI MOTOR S.A.

since 1921 EMIT

General information pages 5-14

Introduction to SIE motors

Vibration and noise level

Permissible loads on the shaft end

Description of the customised executions

Technical data pages 16-20

Dimensional drawings pages 21-30

List of motor parts pages 31-34

Production program page 35

IE1 = Standard Efficiency

2010 2011 2015 2017

IE2 (0,75 - 375kW) Change in the law from 16.06.2011.

IE3 (7,5 - 375kW), IE2 (with VSD)

IE3 (0,75 - 375kW), IE2 (with VSD)

Cantoni Group IE1 motors

Cantoni Group 2SIE motors (IE2)

IE2 High Efficiency (Cantoni)

· Rated voltage up to 1.000 V

Power factor cos ϕ Δcosϕ = -1/6 (1- cosϕN)

Rating and performance IEC 60034-1

New IEC standards regarding efficiency classes (IEC

Insulation class F in an electric motor means that

VIBRATION LEVEL AND NOISE LEVEL

According to the IEC 60034-5 standard the electric motors are

1st digit DESCRIPTION 2nd digit DESCRIPTION 3rd digit DESCRIPTION

Protected against 250 g

Protected against 350 g

7 Protected against immersion 0.5 kg

According to the IEC 60034-7 standard

Horizontal shaft Vertical shaft

Frame size Frame size

IM 1001 IM B3 56 ÷ 500 IM 1011 IM V5 56 ÷ 315

IM 1051 IM B6 56 ÷ 280 IM 1031 IM V6 56 ÷ 315

IM 1061 IM B7 56 ÷ 280 IM 2011 IM V15 56 ÷ 355

IM 1071 IM B8 56 ÷ 280 IM 2031 IM V36 56 ÷ 355

IM 2001 IM B35 56 ÷ 500 IM 3011 IM V1 56 ÷ 500

IM 2101 IM B34 56 ÷ 132 IM 3031 IM V3 56 ÷ 280

IM 3601 IM B14 56 ÷ 132 IM 3631 IM V19 56 ÷ 180

VERSION WITH ROLLER BEARINGS for motors 2SIE315 and 355

Horizontal mounting Vertical operation

VERSION WITH ROLLER BEARINGS for motors SEE355 and Sh355-500

Horizontal mounting Vertical operation

SEE 355 8 210 24 14 6 on request

Sh 355..s 4 210 27 17 6 on request

PERMISSIBLE LOADS ON THE SHAFT END

Other specifications dependent on the frame size:

size of poles Size construction poles, 2p bearing bearing

for horizontal and verical duty.

The bearings in basic

2SIE 225 2÷6 6313 C3 Size construction poles, 2p bearing bearing

SIE 315MC, MD 8 6320C3/6318C3 Sh 400..s IM1001 (B3) 2

2Sg 280 4 ÷ 12 6317 C3 SLh 500..s IM2001 (B35) 4 ÷ 10

56 Aluminium Aluminium Aluminium - screwed

132 160 180 200 225 250 280 315 355