Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Tech DRWG SS3 Mock 2021 Answers

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 11

SECTION B

Answer number 5 and any other three (3) questions

1. An ellipse has a major axis 120 long and its foci are 80 apart
(a) i. Construct the ellipse
ii. Measure and state the length of the minor axis
(b) Draw a tangent and normal to the curve at a point P above the major axis and 35 to
the minor axis.

2. (a) Construct a diagonal scale of 5cm to 1m to read a maximum of 5m and a minimum


of 1cm
(b) Label the scale constructed in 3 (a) and indicate a length of 2m 65cm
(c) i. Use the scale to construct a hexagon of 2.65m across corners
ii. Measure the side of the hexagon

3. The figure above shows crank OQ which rotates in clockwise direction. The rod PQ is
connected to the crank at Q and slides through the slot R.

Plot full size the locus of point P when the crank makes one revolution

4. Plot the locus of a point P on the circumference of a circle diameter 60 rolling along a
straight line without slipping. Construct a tangent and a normal to the locus of a point 50
from the right end of the locus.
Answer only one question in this number (5), either Building Drawing or Mechanical
Drawing

5a. Building Drawing

Specification
Foundation: 675 x 225 concrete strip on 15 blinding at 1000 from ground level.
Walls: all walls are 225 with 12 ceramic tiles wall finish.
Floor: 200 hardcore, 150 concrete slab, 225 terrazzo floor finish, floor level is 450 higher
than ground level, height of floor to ceiling 3100.

Steps: Riser 150, tread 220

Doors: All doors glazed, three panel in 225x 50 timber frame DD 2100 x 1800 x 38,
D – 2100 x 900 x 38 flush wooden in 100 x 50 hardwood timber frame; D1 –
2100 x900 x38
Windows: W- 2000 x 1200 sliding glazed in aluminium frame; W1- 900 x 600 top hung
casement window glazed in aluminium frame.
Lintel: 225 x 225 reinforced concrete at 210 above floor level.
Beam: 2 Nos 225x225 reinforced concrete at 2,350 above floor level
Roof: 350 double pitch, rafter 100 x 50, purlins 100 x 50, struts 100 x 50, wall plate 100 x
75, ceiling joist 50 x 50 at 600 centre to centre, ridge cap 30 x 185, fascia board 28, soffit
board 18, ves projection 900.

(a) Draw, to scale a of 1:100 the

(i) floor plan.


(ii) front elevation.

(b)draw to the scale of 1:50, the sectional view on plane J-J

5b. Mechanical Drawing


The figure below shows the details of belt pulley unit in third angle projection. Assemble
the parts with the shift of position holding the pulling and the washer at face P collar and
pin at face T draw full size in first angle the

(a) Sectional front elevation on K-K


(b) Sectional front elevation on P-P

Answers
Ques.1

Ques.2
Ques.3
Ques.4
5a
5b.
ANSWERS OBJECTIVE 32.A
33.C
1. C
34.B
2. B
35.C
3. A
36.B
4. C
37.C
5. A
38.D
6. A
39.B
7. B
40.D
8. D
9. C
10.A
11.D
12.A
13.D
14.B
15.D
16.B
17.A
18.D
19.A
20.B
21.A
22.C
23.B
24.A
25.B
26.A
27.B
28.D
29.A
30.D
31.B

You might also like