Product Catalogue

Product Catalogue
Cooling Components
• Electronic Controls
• Expansion Valves
• Hot Gas Bypass Valves
• Liquid Injection Valves
• Solenoid Valves
• Check Valves
• Sight Glasses
• Filter Driers
• Vibration Absorbers
Product Catalogue Cooling Components
Content Overview
Designation Page
Electronic Controls
Electronic Expansion Valves
EEV 9
Electronic Superheat Controllers
SHC 15
Accessories for SHC
PSR, TS 19
Electronic Suction Pressure Regulation Valves
ESDR 25
Electronic Thermostats and Cold Store Controls
PCR-100/110 29
PCR-300/310/410/300RC 31
Electronic Temperature Displays
PTI-610 35
Automatic Expansion Valves
Valves with interchangeable orifice
AMV (AMV, AMVX) 37
Valves with fixed orifice
AEL, AEL with Bypass 41
Thermostatic Expansion Valves
Valves with interchangeable orifice
TMV (TMV, TMVX, TMVBL, TMVXBL) 43
TMVL (TMVL, TMVLX) 47
TMX (TMXB, TMXL) 51
Valves with fixed orifice
TLK 55
TLE 0.5 – 3.0 59
TLEX 0.5 – 4.5 59
TBEX 0.5 – 4.5 63
TOEX 0.5 – 4.5 67
TLESX 4.75 – 6 71
TLEX 4.75 – 7 75
TLEX 8 – 11 79
Hot Gas Bypass Valves
CVC, HLE 83
HLEX 4.75 – 7, HLEX 8 – 11 85
Liquid Injection Valves
NMVL 89
NMX 89
Solenoid Valves
M (MA, MD, MS) 95
Check Valves
RV 103
Sight Glasses
SBI, SBIA, SLI 105
Filter Driers
FF 109
Vibration Absorbers
SA 113
Nomenclature 119
Honeywell Product Portfolio 121
EN0H-0376GE23 R1014 · Subject to change without notice 3

Product Overview
Series Description Page
EEV Electronic Expansion Valves 9

bipolar stepper motor and bidirectional flow direction
SHC Electronic Superheat Controllers 15

Automatic adaptation to the evaporator’s MSS
Balancing of the lowest possible superheat
Learning behavior with regards to the history of the operating points
Automatic tracking of controller parameters
ESDR Electronic Suction Pressure Regulation Valves 25

stepper motor operated, continuous control behaviour, Balanced Port, copper
solder connections, low pressure drop, kv – value = 17 m³/h, equivalent to 38
kW cooling capacity R404A
PCR Electronic Thermostats and Cold Store Controls 29

temperature- and cold store controls for snap-in installation and standard
DIN-rail
PTI Electronic Temperature Display 35

temperature display for snap-in installation
AMV Automatic Expansion Valves 37

adjustable evaporating pressure, flare connections, internal pressure
equalisation, interchangeable orifice cartridges
AMVX Automatic Expansion Valves 37

adjustable evaporating pressure, flare connections, external pressure
equalisation, interchangeable orifice cartridges
AEL Automatic Expansion Valves 41

adjustable evaporating pressure, solder connections, internal pressure
equalisation, fixed orifice, bypass optional
TMV Thermostatic Expansion Valves 43

internal pressure equalisation, combi adsorber charge for several refrigerants,
adjustable superheat set, flare connections, interchangeable orifice cartridges
4 EN0H-0376GE23 R1014 · Subject to change without notice

TMVX Thermostatic Expansion Valves 43

external pressure equalisation, combi adsorber charge for several refrigerants,
adjustable superheat set, flare connections, interchangeable orifice cartridges
TMVBL Thermostatic Expansion Valves 43

adjustable superheat setting, inlet flare connection, outlet solder connection,
interchangeable orifice cartridges
TMVXBL Thermostatic Expansion Valves 43

adjustable superheat setting, inlet flare connection, outlet solder connection,
TMVL Thermostatic Expansion Valves 47

part programme valve, one valve body head for solder base with internal (VLS)
or external (VLSX) pressure equalisation, combi adsorber charge for several
refrigerants, adjustable superheat setting, interchangeable orifice cartridges
VLS - D Solder Base for Thermostatic Expansion Valves TMVL and NMVL 47
internal pressure equalisation, solder connections, two-way construction
VLSX - D Solder Base for Thermostatic Expansion Valves TMVL and NMVL 47
external pressure equalisation, solder connections, two-way construction
VLS - W Solder Base for Thermostatic Expansion Valves TMVL and NMVL 47
internal pressure equalisation, solder connections, angle construction
VLSX - W Solder Base for Thermostatic Expansion Valves TMVL and NMVL 47
external pressure equalisation, solder connections, angle construction
VD Orifice Cartridge for Thermostatic Expansion Valves TMV, TMVL and 43

NMVL 47
for all expansion valves of series TMV, TMVX, TMVBL, TMVXBL, TMVL and
NMVL, orifice size 0.3 to 4.75, equivalent to 0.5 - 21.5 kW cooling capacity R22

Übersicht
TMX Thermostatic Expansion Valves 51

part programme valve, valve body head can be combined with various bases
and orifice cartridges, MOP – or liquid charge, warm thermal head, external
pressure equaliser in the valve body, adjustable superheat setting, with
Balanced-Port, interchangeable orifice cartridges
XLS Solder Base for Thermostatic Expansion Valves TMX and NMX 51
solder connections, two-way or angle construction
XBS Flare Base for Thermostatic Expansion Valves TMX and NMX 51
flare connections, two-way construction
XD Orifice Cartridge for Thermostatic Expansion Valves TMX and NMX 51

for expansion valves of series TMX and NMX
orifice size 4.5 to 10, equivalent to 16.3 - 72.1 kW cooling capacity R22
TLK Thermostatic Expansion Valves 55

internal pressure equalisation, MOP charge, warm thermal head, fixed
superheat setting, solder connections, fixed orifice, orifice size 0.3 to 2.0,
equivalent to 0.5 - 3.9 kW cooling capacity R22, bypass optional
TLE 0.5 - 3.0 Thermostatic Expansion Valves 59

MOP charge at deep freeze applications, warm thermal head, adjustable
equivalent to 1 - 8.9 kW cooling capacity R22
TLEX 0.5 - 4.5 Thermostatic Expansion Valves 59

MOP charge at deep freeze applications, warm thermal head, adjustable
equivalent to 1 - 16.3 kW cooling capacity R22
TBEX 0.5 - 4.5 D Thermostatic Expansion Valves 63

TBEX 0.5 - 4.5 W on request, external pressure equalisation, combi adsorber charge or MOP
charge, warm thermal head, two-way or angle construction, adjustable
superheat setting at two-way construction, flare connections, fixed orifice, orifice
size 0.5 to 4.5, equivalent to 1 - 16.3 kW cooling capacity R22

TOEX 0.5 -4.5 D Thermostatic Expansion Valves 67

TOEX 0.5 - 4.5 W on request, external pressure equalisation, combi adsorber charge or MOP
charge, warm thermal head, two-way or angle construction, adjustable
superheat setting at two-way construction, o-ring connections, fixed orifice,
orifice size 0.5 to 4.5, equivalent to 1 - 16.3 kW cooling capacity R22
TLESX 4.75 - 6 Thermostatic Expansion Valves 71

external pressure equalisation, MOP charge, warm thermal head, adjustable
superheat setting, Single Port, solder connections, fixed orifice, orifice size 4.75
to 6, equivalent to 21.5 – 40.7 kW cooling capacity R22
TLEX 4.75 - 7 Thermostatic Expansion Valves 75

TLEX 8 - 11 external pressure equalisation, MOP charge, warm thermal head, adjustable 79
superheat setting, Balanced Port, solder connections, fixed orifice, orifice size
4.75 to 11, equivalent to 21.5 - 92 kW cooling capacity R22
CVC Hot Gas Bypass Valves 83

capacity regulator, internal pressure equalisation, adjustable suction pressure
limitation 1 – 6 bar, solder connections, fixed orifice, orifice size 4, equivalent to
1 kW bypass capacity R134a
HLE Hot Gas Bypass Valves 83

capacity regulator, internal pressure equalisation, adjustable suction pressure
limitation 1 – 9 bar, solder connections, fixed orifice, orifice size 4.5S,
equivalent to 1.5 kW bypass capacity R134a
HLEX 4.75 - 7 Hot Gas Bypass Valves 85

HLEX 8 - 11 capacity regulator, external pressure equalisation, adjustable suction pressure
limitation 1 - 9 bar, Balanced Port, solder connections, fixed orifice, orifice size
4.75 - 11, equivalent to 1 - 7.2 kW bypass capacity R134a
NMVL Liquid Injection Valves 89

suction pressure controlled valve, part programme valve, only one valve body
head is needed for solder base with internal (VLS) or external (VLSX) pressure
equalisation, liquid charge, adjustable superheat setting, interchangeable orifice
cartridges
NMX Liquid Injection Valves 89

suction pressure controlled valve, part programme valve, valve body can be
combined with various bases and orifice cartridges, liquid charge, warm thermal
head, external pressure equalisation in the valve body head, adjustable
superheat setting, with high pressure compensation (Balanced-Port),

MA Solenoid Valves 95
normally closed, direct operated, angle construction, solder connections,
kv-value = 0.17 m3/h
MD Solenoid Valves 95
normally closed, direct operated, two-way construction, solder or flare
connections, kv-value = 0.17 – 0.23 m3/h, valve complete with coil for 230V AC
or as part programme valve without coil
MS Solenoid Valves 95
normally closed, pilot operated, two-way construction, solder or flare
connections, kv-value = 0.9 – 4 m3/h, valve complete with coil for 230V AC or as
part programme valve without coil
MC Coil for Solenoid Valves MA, MD, MS 95

as spare part or for part programme
RV Check Valves 103

brass housing, copper-plated solder connections, for installation in the liquid,
hot gas or suction line
SBI Sight Glasses 105

with moisture indicator, flare connections on both sides
SBIA Sight Glasses 105

with moisture indicator, flare connections female / male thread
SLI Sight Glasses 105

with moisture indicator, solder connections on both sides
FF Filter Driers 109

for installation in liquid line, solder or flare connections, drier size 030 to 410
SA Vibration Absorber 113

laser welded, stainless steel hose, copper fittings, frost resistant construction,
suitable for vertical installation

Series EEV
ELECTRONIC EXPANSION VALVE
WITH STEPPER MOTOR
PRODUCT-DATA
Features
 Proportional Electronic Expansion Valve for usage in
refrigeration circuits
Refrigerants:
HCFC, HFC (R410A, R32, R407C, R134a, R404A, ...)
HFOs (R1234yf, R1234ze) and blends
Hydrocarbons (R600a, R290, ...)
Further refrigerants on request
 2-pole stepper motor with inside protected coil
 Hermetical construction
Specification
Operating Temperature Medium: -40 ... +75 °C

(90 °C in reverse mode)
Ambient: -50 ... +70 °C
Biflow 100 % cooling capacity in
both directions
MOP (= PS) 47 bar (abs)
MOPD 42 bar
Application
Total steps 473
The electronic expansion valves EEV are designed to be
installed in refrigeration circuits as expansion devices to ex- Rangeability 1:15
pand the refrigerant. The electronic expansion valve will be Stator / Actuator 2 Phasen Bipolar
driven by a controller which gets a pressure and temperature
Nominal voltage 24 V DC +/- 10 %
signal from the outlet of the evaporator to control the super-
heat of refrigerant. Nominal phase current 0,2 A
To drive the EEV a Honeywell-Controller or a common stepper Maximum phase current 0,75 A (short term)
motor driver is recommended to be used.
short term = 10 steps
Holding current max 0,04 A
Nominal power 4,08 W
Materials Stepper motor drive frequen- 60 Hz (full step/sec)
Body Brass, Stainless steel cy
Valve sealing PTFE Reliability 250.000 full strokes
Port Connections Copper 120.000.000 steps
Motor Copper, electrical sheet

Series EEV
Cooling Capacity QN (kW)

Operation Conditions:
Condensing temperature tc: 38 °C;
Evaporating temperature to: 4 °C;
Subcooling: 1 K
Cooling Capacity QN (kW)

Valve Type
R134a R450A R1234yf R407C R407F R290 R410A
EEV 5 3.3 2.9 2.4 4.4 4.6 4.4 5.0
EEV 10 6.6 5.8 4.8 8.7 9.2 8.9 10.0
EEV 20 14.0 12.2 10.1 18.3 19.4 18.65 21.0
The application-oriented valve calculation can take place in individual cases with the help of the selection tables.
Electrical Connections
Stepper Motor
Controller

24 V
 White
 Blue
 Black
 Brown
Step    
1 + - - +
2 - - + +
3 - + + -
4 + + - -

Dimensions and Weights
Port Connections
Typ Weight (kg)
A-B
EEV 5 10 mm - 12 mm ODF 0,33
3/8“ – 1/2" ODF 0,33
EEV 10 10 mm - 12 mm ODF 0,33
3/8“ – 1/2" ODF 0,33
EEV 20 12 mm - 16 mm ODF 0,33
1/2“ – 5/8" ODF 0,33

Series EEV
Type description
EEV 20 12 x 16
Valve type
Valve size
5
10
20
Port Connection
10 x 12 = 10 x 12 mm ODF
12 x 16 = 12 x 16 mm ODF
3/8 x 1/2 = 3/8” x 1/2” ODF

1/2 x 5/8 = 1/2” x 5/8” ODF

Assembly
 Respect the installation instruction!
 Main direction s. Valve body.
 Horizontal to vertical (connection on top)
 Protect EEV from humidity and dripping water.
 Wrap a wet rag around on the valve and perform the
welding without overheating the valve.
 Aim the flame towards the ends of the fittings.
 Let EEV cool down.
 Connect pre-wired connector to the socket on
the stepper motor and tighten the screw to a
maximum torque of 0,6 Nm
 Connect four-pin end of the cable to the corres-
ponding terminals on the Honeywell controller
according the wiring diagram of the controller.

Series SHC
SUPERHEAT CONTROLLER – OEM VERSION
PRODUCT DATA
Features
 Automatic adaptation to the evaporator’s MSS
 Balancing of the lowest possible superheat
 Learning behavior with regards to the history of the
operating points
 Automatic tracking of controller parameters
 Independent recognition of defrost requirements
 Termination of the defrost cycle commensurate with
energy efficiency needs
 No external setpoint necessary!
Specification
Analog outputs
Temperature 2X (PT1000, NTC10K, NTC20K)
Temperature/voltage 2X (PT1000, NTC10K, NTC20K,
0.5 … 4.5 V, 0 … 10 V)
Voltage/current 2X (0.5 … 4.5 V, 0 … 10 V,
4 … 20 mA)
Analog output
Voltage 1X (0 … 10 V)
Stepper motor outputs

For bipolar stepper motor 4X (12 V or 24 V, max. 800 mA
General per phase, max. 500 steps / sec)
SHC Electronic Superheat Controllers are suitable for use in Digital outputs
compression refrigeration plants and heat pumps for the Relays 4X (230 VAC, 5 [2] A)
control of electronic expansion valves of the type EEV.
Battery input
Generally, the suction line pressure and the temperature of
the superheated refrigerant are the critical measurement Buffer 24 V, min. 1 Ah
values. The superheat of the refrigerant is regulated at the
evaporator’s outlet. Ambient Storage and Operating Conditions
Storage temperature -25...+70 °C
Operating temperature -25…+60 °C
Relative humidity 10…90% (non-condensing)
Protection Class IP00 (no housing)
CONDENSER / VERFLÜSSIGER
Power Supply
SHC COMPRESSOR Current 24 VAC ± 20% or
KOMPRESSOR
24 VDC ± 10%
EEV Max. power consumption 50 VA (when motor active)
Mounting
Mounting DIN rail or wall mounting
Dimensions 181 mm X 110 mm X 45 mm
EVAPORATOR / VERDAMPFER
Weight 220 g
PI TI
MU0B-0639GE51 R0410 · Subject to change without notice 15

Series SHC
Function Valve Control

The Honeywell SHC Controller operates with a 24 VAC/DC The Honeywell SHC Controller is capable of driving EEV
power supply. The controller uses the signals from the electronic expansion valves with stepped motors from various
temperature sensor and the pressure sensor located at the different manufacturers. However, the use of Honeywell EEV
evaporator outlet (alternatively: temperature sensors at the valves of the type EV2, EV3, and EV4 is to be preferred.
evaporator inlet and outlet) to determine the actual superheat of Alternatively, electronic control valves can be driven with
the refrigerant at the evaporator outlet and controls the EEV standard 0…10 V signals via the controller’s analog output.
electronic expansion valve so as to ensure that the lowest The control parameters of the given valve are to be adjusted
possible superheat at the operating point is achieved. at the controller.
To do this, the SHC Controller requires no external setpoint
provided by operating personnel or another controller. The
controller, itself, determines the optimal setpoint for the (given)
operating point. By altering the operating point, the Valve Parameters
corresponding optimal setpoint for superheat of the refrigerant is Type of Drive
determined and controlled. The SHC Controller always operates
Type Bipolar stepped motor,
along the evaporator’s Minimal Stable Signal (MSS).
modulating actuator with 0…10 V
For every operating point, the PID parameters of the controller analog output
are automatically tracked and the control behavior optimized.
Because of the ability of the Honeywell SHC Controller to store
historical operating data, it “learns,” over the course of time, the Stepped Motor Parameters
refrigeration circuit’s evaporator characteristics (MSS). In the Motor voltage 12 V or 24 V
event of a change in load in the refrigeration circuit, the SHC Step frequency 10…500 steps/sec
Controller is capable of immediately achieving the optimal Motor current 80…800 mA
operating point. This yields very dynamic control and resultant Holding current 0…100% of the motor current, in
high energy efficiency. approx. 10% steps
Max. no. of steps 1…10,000 steps
No. of opening steps 1…1,000 steps
Terminal Connection Diagram
39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
GND D1 D2 D3 GND GND AO R1 GND V5/15 GND R2 U2 V5/15 GND U1 T2 GND T1
digital inputs 0...10 V output inputs: 4...20 mA / ratiometric / 0...10 V inputs: Pt1000, NTC10k, NTC20k / ratiometric / 0...10 V
24 Vac/dc 24 Vbat bipolar stepper motor RS485 (isolated) relay 4 (SPDT) relay 1 (NO) relay 2 (NO) relay 3 (NO)
G G0 BAT EARTH OUT2B OUT2A OUT1B OUT1A A B GNDX C4 NO4 NC4 C1 NO1 C2 NO2 C3 NO3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
CONNECTION OF THE RELEASE/ENABLER SIGNAL (DI1, FACTORY DEFAULT)

The SHC Controller is active when the contact is closed.
39 38 37
GND D1 D2
16 MU0B-0639GE51 R0410 · Subject to change without notice

Terminal Assignment
term. # name description
1 G voltage supply 24 VAC/DC (+)
2 G0 voltage supply 24 VAC/DC (-)
3 BAT buffer battery module 24 V (+) with power level indicator
4 EARTH earth / shielding

5 OUT2B output 2B of stepped motor
6 OUT2A output 2A of stepped motor
7 OUT1B output 1B of stepped motor
8 OUT1A output 1A of stepped motor
9 A RS485, A + conductor
10 B RS485, B – conductor
11 GNDX RS485, isolated ground
12 C4 relay 4, change-over contact

13 NO4 relay 4, normally-open contact NOC
14 NC4 relay 4, normally-closed contact NCC
21 T1 AIN1: temperature input 1 (NTC10K, NTC20K, Pt1000)

22 GND AIN1/2: ground for temperature inputs 1 + 2
23 T2 AIN2: temperature input 2 (NTC10K, NTC20K, Pt1000)
24 U1 AIN3: universal input 1 (NTC10K, NTC20K, Pt1000, 0.5…4.5 V ratiometric, 0…10 V)
25 GND AIN3/4: ground for universal inputs 1 + 2
26 V5/15 AIN3/4: sensor voltage supply for universal inputs 1 + 2
27 U2 AIN3: universal input 2 (NTC10K, NTC20K, Pt1000, 0.5…4.5 V ratiometric, 0…10 V)
28 R2 AIN6: current/voltage input 2 (0.5…4.5 V, 0…10 V, 4…20 mA)

29 GND AIN6: ground for current/voltage input 2
30 V5/15 AIN5/6: sensor voltage supply for current/voltage inputs 1 + 2
31 GND AIN5: ground for current/voltage input 1
32 R1 AIN5: current/voltage input 1 (0.5…4.5 V, 0…10 V, 4…20 mA)
33 AO AO1: analog output 1 (0…10V)

34 GND AO1: ground for analog output 1
35 GND DI1/2/3: ground for digital inputs 1 + 2 + 3
36 D3 DI3: digital input 3 (log.1 = contact open or 24 VAC/DC, log.0 = short-circuit or < 2 VAC/DC)
39 GND DI1/2/3: ground for digital inputs 1 + 2 + 3
LED Blink Coding

status LED (yellow) alarm LED (red)
ON plant is switched OFF (safety position) 1 x battery supply
1x switch ON phase or EEV active (opening/closing) 2 x superheat too low
2x switch relay active, switch delay running 3 x superheat too high
3x start-up function active (ramp, incl. holding time) 4 x sensor failure
4x pump down active or compressor restart block 5 x LOP active
5x MOP active 6 x configuration failure
6x HIT active 7 x communication failure
7x waiting for release conditions 8 x Hardware self-test failure
8x EEV in manual mode
MU0B-0639GE51 R0410 · Subject to change without notice 17

Series SHC
Dimensions (mm)
40 181
110
Accessories
accessories models corresponding technical literature
Transformer CRT / ETR EN0B-0568GE51
Temperature Sensor TS-NFN, TS-NFR, TS-RFH EN0H-1950GE23
Pressure Sensor PSR EN0H-1949GE23
DPTM50-5000 EN0B-0466GE51
Differential Pressure Sensors
DPTM50D-5000D EN0B-0616GE51
Electronic Expansion Valve EEV EN0H-1945GE23
18 MU0B-0639GE51 R0410 · Subject to change without notice

Series PSR
PRESSURE SENSOR TRANSMITTER
FOR REFRIGERATION AND HVAC APPLICATIONS
PRODUCT-DATA
Features
 Pressure Sensor Transmitter for usage in
refrigeration and HVAC applications
 For installation in liquid line, injection line, hot gas
line and suction line
 For usage of refrigerants R22, R134a, R404A, R407C,
R410A, R502, R507; not for Ammonia
 Condensation-tight
 Type PSR - ** MS UB MP150:
 Wetted parts of brass, CR70 (Chloroprene) and
ceramic
 Integrated ceramic thick-layer sensor
 Type PSR - ** VA UB MP150:
 Wetted parts of stainless steel
 Monolithic structure
 Hermetically welded metallic, dry thin-film sensor
element
Specification
Pressure Range see table on page 20
Maximum Pressure PS see table on page 20
Application Electrical Output Signal 0.5…4.5 V ratiometric
Pressure Sensor Transmitter Type PSR is used in refrigeration
Power Supply 5 ± 0.5 VDC
circuits to measure the refrigerant’s pressure.
The Pressure Sensor Transmitter PSR can be used according Supply Current ≤ 10 mA
to its measuring range in the liquid line, in the injection line,
Maximum Load > 4.5 kΩ
in the hot gas line and in the suction line of refrigeration
circuits. Response Time (10…90%) ≤ 5 ms
Insulation Voltage 500 VDC
Materials Medium Temperature -40 °C … 80 °C
Housing Brass, Stainless Steel Ambient Temperature -25 °C … 80 °C
Sealing CR70 (Chloroprene) Storage Temperature -25 °C … 80 °C
Port Connection 7/16-20 UNF-2B Max. rel. Humidity 95 %
Electr. Protection degree IP67
Other appplications on request.
In plugged condition with connector of corresponding
protection class

Series PSR
Technical Specification
Typ PSR – 9 MS PSR – 16 MS PSR – 45 MS PSR – 9 VA UB PSR – 16 VA PSR – 45 VA UB
Type UB MP150 UB MP150 UB MP150 MP150 UB MP150 MP150
Messbereich -1…9 bar(ü) 0…16 bar(ü) 0…45 bar(ü) -1…9 bar(ü) 0…16 bar(ü) 0…45 bar(ü)
Pressure range -1…9 bar(g) 0…16 bar(g) 0…45 bar(g) -1…9 bar(g) 0…16 bar(g) 0…45 bar(g)
Überlastgrenze
20 bar 40 bar 100 bar 20 bar 32 bar 100 bar
Over pressure range
Berstdruck
25 bar 50 bar 120 bar 100 bar 160 bar 400 bar
Burst pressure
Genauigkeit -40 °C … -20 °C ≤ 1,5 %* -40 °C … -20 °C ≤ 1,5 %*
Accuracy -20 °C … +20 °C ≤ 1 %* -20 °C … +20 °C ≤ 1 %*
* bezogen auf Taulinie von R410A * bezogen auf Taulinie von R410A
* related to dewpoint of R410A * related to dewpoint of R410A
Stabilität pro Jahr ≤ 0,3 % der Spanne (bei Referenzbedingungen)
1-year stability ≤ 0.3 % of span (at reference conditions)
Elektrische Schutzart
IP67 in gestecktem Zustand mit Leitungsstecker entsprechender Schutzart
Protection degree
Kurzschlussfestigkeit
S+ gegen 0V S+ gegen UB-
Short-circuit protection
S+ towards 0V S+ towards UB-
Verpolschutz
UB gegen 0V UB+ gegen UB-
Reverse polarity
UB towards 0V UB+ towards UB-
protection
Überspannungsschutz
Overvoltage protection 36 VDC
Material Messing, Keramik AI203 96 %

Material O-Ring: CR70 (Chloropren) Edelstahl (316L)
Brass, Ceramic AI203 96 % Stainless steel (316L)
O-Ring: CR70 (chloroprene)
Gehäuse Messing Edelstahl (316L)
Body Brass Stainless steel (316L)
EMV-Richtlinie 2004/108/EEC, EN 61 326 Emission (Group 1, 2004/108/EEC, EN 61 326 Emission (Group 1, Class B)
EMC directive Class B) and Immunity (industrial locations) and Immunity (industrial locations)
2004/108/EEC, EN 61 326 Emission (Group 1, 2004/108/EEC, EN 61 326 Emission (Group 1, Class B)
Class B) and Immunity (industrial locations) and Immunity (industrial locations)
Gewicht Ca. 0,08 kg Ca. 0,08 kg
Weight Appr. 0.08 kg Appr. 0.08 kg

Type Description
Pressure Sensor Transmitter
PSR -9 MS UB MP150
Pressure Sensor Type
Type:
-9 = -1 … 9 bar(g)
16 = 0 … 16 bar(g)
45 = 0 … 45 bar(g)
Material:
MS – Brass
VA – Steinless Steel
Port Connection
7/16-20 UNF-2B, Schrader
Internal Thread
MetriPack 150
Port Connections Electrical Connections

Type Port Connection 3-pole Connector Metri Pack Series 150
PSR – 9 MS UB MP150 7/16’’ UNF UB = B
PSR – 16 MS UB MP150 7/16’’ UNF 0V = A
PSR – 45 MS UB MP150 7/16’’ UNF S+ = C
PSR – 9 VA UB MP150 7/16’’ UNF
PSR – 16 VA UB MP150 7/16’’ UNF
PSR – 45 VA UB MP150 7/16’’ UNF

Series PSR
Function Assembly
The pressure prevailing within the application is transformed  Required tools: wrench (flats 24), screw driver
into a standardised electrical signal through the deflection of  Use the pressure transmitter only if it is in a faultless
the diaphragm, which acts on the sensor element with the condition as far as the safety-relevant features are
power supply fed to the transmitter. This electric signal concerned.
changes in proportion to the pressure and can be evaluated
correspondingly.  When mounting the instrument, ensure that the
sealing faces of the instrument and the measuring
point are clean and undamaged.
Remarks:
 Screw in or unscrew the instrument only via the flats
 Select the appropriate pressure transmitter with using a suitable tool and the prescribed torque. The
regard to scale range, performance and specific appropriate torque depends on the dimension of the
measurement conditions prior to installing and starting pressure connection. Do not use the case as working
the instrument. surface for screwing in or unscrewing the instrument.
 Observe the relevant national regulations (e.g.: EN
 When screwing the transmitter in, ensure that the
50178) and observe the applicable standards and
threads are not jammed.
directives for special applications (e.g. with
dangerous media such as acetylene, flammable  Connect the instrument to earth via the pressure
gases or liquids and toxic gases or liquids and with connection.
refrigeration plants or compressors). If you do not  Use power supplies which guarantee reliable electrical
observe the appropriate regulations, serious isolation of the operating voltage as per IEC/DIN EN
injuries and/or damage can occur! 60204-1. Consider also the general requirements for
 Open pressure connections only after the system PELV circuits in accordance with IEC/DIN EN 60204-1.
is without pressure!  Ingress protection per IEC 60529 (The ingress
 Please make sure that the pressure transmitter is protection classes specified only apply while the
only used within the overload threshold limit all the pressure transmitter is connected with female
time! connectors that provide the corresponding ingress
 Observe the ambient and working conditions protection).
outlined in section „Technical data”.  Please make sure that the ends of cables with flying
 Ensure that the pressure transmitter is only operated leads do not allow any ingress of moisture.
in accordance with the provisions i.e. as described in
the installation instructions.
 Do not interfere with or change the pressure
transmitter in any other way than described in the Spare Parts
operating instructions.
 Remove the pressure transmitter from service and Cable
mark it to prevent it from being used again Description:
accidentally, if it becomes damaged or unsafe for
operation. Stecker mit Kabel für Drucksensor 3 m (IP67)
PSR-CAB300 MP150
 Take precautions with regard to remaining Plug with cable for pressure sensor 3 m (IP67)
media in removed pressure transmitter.
Stecker mit Kabel für Drucksensor 6 m (IP67)
Remaining media in the pressure port may be PSR-CAB600 MP150
hazardous or toxic! Plug with cable for pressure sensor 6 m (IP67)
 Have repairs performed by the manufacturer only.

Colour of single wire:
A Green Earth Connection
B Brown Power Supply
C White Output Signal
Temperature Range: -40 °C … 85 °C

Series TS
TEMPERATURE SENSOR
FOR REFRIGERATION AND HVAC APPLICATIONS
PRODUCT-DATA
Features
 Pressure Sensor Transmitter for usage in
refrigeration and HVAC applications
 For installation in liquid line, injection line, hot gas
line and suction line
 For usage of refrigerants R22, R134a, R404A,
R407C, R410A, R502, R507; not for Ammonia
 Condensation-tight body IP67
 Type TS – NFN & TS – NFR: NTC 10K
 Type TS – RFH: PT1000
Specification (1)
Application
Resistance Value:
Temperature Sensor Type TS is used in refrigeration circuits
TS – NFN; TS – NFR 10 kΩ at 25 °C
to measure the refrigerant’s temperature.
The Temperature Sensor TS can be used according to its TS – RFH 1 kΩ at 0 °C
measuring range in the liquid line, in the injection line, in the Accuracy:
hot gas line and in the suction line of refrigeration circuits.
Due to fast temperature capture in refrigeration circuits the TS – NFN 1 % Full scale
signal can be communicated very fast. TS – NFR ± 0.2 °C
TS – RFH Class A
Materials Response Time: K = 5 sec in liquid V = 2 m/s
Body Stainless Steel, AISI 304 Sensitivity:
Cable Thermical rubber poly. TS – NFN; TS – NFR NTC 10K fast
Electrical Connection Pins TS – RFH PT1000
Measuring Range: -50 °C … +110 °C
Types Storage Temperature -25 °C … 80 °C

Ambient Temperature -25 °C … 80 °C
Description Sensor Type Temperature Range
Electrical Connection 2-wire
TS - NFN NTC 10K Fast -50 °C … 110 °C
Dimension Ø 4 mm; l = 40 mm
TS - NFR NTC 10K Fast -50 °C … 110 °C
Connecting Cable 3m
TS - RFH PT1000 -50 °C … 110 °C
Insulation Voltage 250 VAC
Electr. Protection
degree: IP67

Series TS
Specification (2)
Type TS – NFN TS – NFR TS – RFH
Element Type NTC 10K 1% BETA 3435 NTC 10K BETA 3977 tolerance ± 0.2 °C PT 1000 Class A
Cable Type Thermical rubber poly Thermical rubber poly Thermical rubber poly
Cable colour Black Yellow Green
Cable diameter 2x0.25 mm² Ø 3.3 mm 2x0.25 mm² Ø 3.3 mm 2x0.25 mm² Ø 3.3 mm
Connection Pins Pins Pins
Filling Polyuretanic resin Polyuretanic resin Polyuretanic resin
Type Description Electrical Connections

Temperature Sensor
TS NFN Connection of Temperature Sensors according below

picture. Temperature Sensor is insensible against
Type reverse polarity. TS Sensors have a 2-wire structure. To
Type: minimize electromagnetic perturbation the cable should
NFN = NTC 10K 1% Beta 3435 be as short as possible.
NFR = NTC 10K Beta 3977 ±0.2°C
RFH = Pt 1000 class A
Function
Due to temperature changes the resistance of temperature sensor will be changed. This change of resistance is changing
proportional to the temperature and can be evaluated accordingly.
Remarks:
 Select the appropriate temperature sensor with regard to scale range, performance and specific measurement conditions
prior to installing and starting the refrigeration system.
 Please make sure that the temperature sensor is only used within the valid measuring range.
Assembly
 Position the temperature sensor on the refrigerant pipe in the position between 10 and 14 o'clock (at horizontal pipe installation).
 Pay attention to install sensor to clean and intact surfaces at the measuring point.
 Provide sufficient thermal compound at the measuring point between temperature sensor and measuring surface.
 Fasten the temperature sensor by means of aluminum tape and/or fastening clips to the refrigerant pipe.
 Insulate the fastened temperature sensor with heat insulation material.
 Connect the temperature sensor according to the instructions of the evaluating equipment.
 Ensure that no humidity may enter at cable-ends.

Series ESDR
ELECTRONIC SUCTION PRESSURE REGULATION VALVE
STEPPER MOTOR OPERATED
PRODUCT DATA
Features
 Stepper motor operated
 Continuous control behaviour
 High pressure compensation (Balanced port)
 Low pressure drop
 High cooling capacity
 Copper solder connections
 Refrigerant: R134a, R404A, R407C, R410A, R422D
Technical Data
Nominal capacity see table on page 26
Maximum pressure PS 35 bar
Maximum test pressure PF 38.5 bar
Min. operating temperature -50 °C
ESDR 22 Max. operating temperature +65 °C
Max. ambient temperature +100 °C
Electronic Data
Stepper motor type 2 phase bipolar
Application Nominal voltage 12 V chopper controlled
Electronic suction pressure regulation valves series ESDR Nominal phase current 0,7 A
are used to control the refrigerant mass flow in the suction
line of a refrigerating plant. Max. phase current 1A
A stepper motor driven piston opens / closes the valve seat. Holding current max. 0,7 A
With this continuous control behaviour it is possible to hold a Step rate 300 Hz
defined temperature level in a cold store also with changing Phase resistance 6 Ohm
compressor working conditions.
It is also possible to handle different temperature levels in Phase inductance 14 mH
several cold stores with a common compressor pack by use Step angel 1.8 °
of suction pressure regulation valves.
Furthermore an overload protection of the compressor or a
capacity controller can be realised with ESDR valves. Material
Valve housing, internals brass
Motor housing stainless steel
Connections copper
Valve sealing PTFE
Motor electrical sheet, copper

Series ESDR
Nominal Capacity
kv – value Nominal capacity (kW)*
Type Valve size (m³/h)
R134a R404A R407C R410A R422D
ESDR 22 17 34.9 37.8 42.7 55.5 34.5
* Capacities are based on evaporating temperature to = +4 °C, condensing temperature tc = +38 °C und 1 K subcooled
refrigerant, pressure drop over the valve 0.15 bar

Type Valve size Dimensions Weight
ØA B C D
22 mm ODF
ESDR 22 185 mm 201.4 mm 113.6 mm approx. 1.05 kg
28 mm ODF
ESDR 22
Type Code / Order Information

ESDR 22 22 x 22mm
Series
Valve seat diameter / Valve size
Solder connections ODF
(Inlet x Outlet)

Wiring Schematic for Stepper Motor
Stepper Motor
Driver

 White
 Blue
 Black
 Brown
Step     open close

1 + - - +
2 - - + +
3 - + + -
4 + + - -
Application Sample
Controller
SM
Driver
T1
T2

Series ESDR
Installation
 Respect the installation instruction!
 Position of the stepper motor in a suspended arrangement.
 Flow direction must correspond with the arrow on the valve
body.
 When soldering the valve, the valve body must not get
warmer than 100 °C.
 Do not direct connect the stepper motor to power supply.
Use a stepper motor driver to operate the stepper motor.
 The technical data of the stepper motor driver must
correspond with the electrical and technical data of the
valve.
 To open / close the valve via a stepper motor driver
respect the sequence of polarity at the coils shown in the
wiring schematic.
 Constructive modifications at the valve are not allowed.
Information for original equipment manufacturers:

The valve series ESDR can be customised to the
requirements of our series device in an optimum way.
Contact us!

Series PCR-100 / PCR-110
ELECTRONIC THERMOSTATS
PRODUCT DATA
Features
 User friendly programming
 Thermostat for refrigeration and heating
 Relay output
 Defrost option for plus cold stores with continuous
operation of evaporator fan
 Alarm output relay
 Red digital display, good visibility
 PCR-100: Module housing for 35 mm standard DIN rail
 PCR-110: Snap-in installation housing for aperture
28.5 x 70.5 mm
PCR-100
 PTC sensors with stainless steel sleeves
 Mains transformer integrated
Specification
Power supply 230 V, ±10 %, 50/60 Hz
Power consumption 2.1 Watt
Control performance on-off
PCR-110 Display 3-digit, 7-segment, LED red,
height 14.2 mm
Resolution 1K
Display accuracy ±0.5 K internally, ±1 digit at 25 °C
Application
Measuring range -55 °C to +50 °C
PCR-100 and PCR-110 are microprocessor-controlled
Input 1 PTC sensor
thermostats for refrigeration, deep freeze systems and for
general purpose use. Outputs compressor or heater: 1 relay
The electronic thermostats can be used for cooling and with changeover contact, 8 A,
heating application in a temperature range of -55 °C to +50 °C. 230 V AC resistive load
alarm: 1 relay with N. O. contact,
Material 5 A, 230 V AC, resistive load
Housing ABS-plastic, self-extinguishing Sensor PTC sensor, cable length 2.5 m,
accuracy ±2 %
range of use:
-30 °C to +80 °C cable not fixed
-40 °C to +80 °C cable fixed
Ambient in operation:
temperature/humidity 0° to + 50 °C,
30 to 85 % R.H. excluding dew
in storage:
-20 °C to +80 °C
Data back up Non-volatile memory EEPROM
Connectors 250V / 10 A screw-type terminal
strips, max. 1.5 mm²
Protective rating Housing: IP 20, front panel: IP 52,
protection class 2

Series PCR-100 / PCR-110
Dimensions and Weight

Type Dimensions of housing (mm) Weight
(kg)
W H D
PCR-100 70 85 61 approx. 0.33
PCR-110 70 32 74 approx. 0.24
Installation
 Operate only in dry places
 Snap-in installation housing:
 Fit unit in a recess 28.5 x 70.5 mm
 maximum wall thickness: 22 mm
 Secure housing with the mounting frame
 4 DIN standard modular housing:
 Open out the side mounting tabs
 Clip the unit on to 35 mm rail
 press tabs in again
 Respect the wiring diagram
 Tighten screws of connectors carefully
PCR-110 PCR-100

Series PCR-300/-310/-410/-300RC
ELECTRONIC COLD STORE CONTROLS
PRODUCT DATA
Features
 User friendly programming
 Compressor control with delayed start-up
 Evaporator fan control; fan in combination with
compressor, operating continuously or switched via
the evaporator temperature.
 Defrost control for electrical heating or hot-gas
defrosting; initiated via programmable time intervals,
at PCR-300RC by real-time clock
 Alarm output (not for PCR-310)
PCR-300  Module housing for 35 mm standard DIN rail at
PCR-300 and PCR-300RC
 Snap-in installation housing at PCR-310 and PCR-410
for aperture 28.5 x 70.5 mm
 Mains transformer integrated at PCR-300, PCR-300RC
 External transformer at PCR-310, PCR-410
 2 PTC sensors with stainless steel sleeves for room
temperature and defrost termination
PCR-310
Specification (1)
Power supply PCR-300, PCR-300RC
mains transformer installed:
Application 230 V, ±10 %, 50/60 Hz
PCR-300, PCR-310, PCR-410 and PCR-300RC are PCR-310, PCR-410
microprocessor-controlled cold store controls for refrigeration 12 V AC ±10%, 50/60 Hz or
and deep freeze systems. 12 V DC ±10%
The control switch the compressor, evaporator fan and the external Transformer TR-310:
defrost heating depending on the cold store temperature Prim.: 230 V AC ±10%, 50/60 Hz
and the adjusted parameters. Sec.: 12 V AC
Material
Control performance on/off
Housing ABS-plastic, self-extinguishing
Display 3-digit, 7-segment, LED red,
height 14.2 mm
Resolution 1K
Inputs 2 PTC sensors
Continued on page 32

Series PCR-300/-310/-410/-300RC
Specification (2)
Outputs compressor: Sensor PTC sensor, cable length 2.5 m,
1 relay with changeover contact, 8 A, accuracy ±2 %
230 V AC, resistive load range of use:
evaporator fan: -30 °C to +80 °C cable not fixed
1 relay with N.O. contact, 8 A -40 °C to +80 °C cable fixed
(5 A PCR-300RC), 230 V AC, Ambient in operation:
resistive load temperature/humidity 0° to 50 °C,
defrost heating: 30 to 85 % R.H. excluding dew
1 relay with N.O. contact, 8 A in storage:
(5 A PCR-300RC), 230 V AC, -20 °C to +80 °C
resistive load
Data back up Non-volatile memory EEPROM,
alarm: Real time clock with back up
PCR-300, PCR-300RC battery (PCR-300RC)
Opto-bidirectional triode thyristor,
250 VAC, min. load 40 mA, Connectors 250V / 10 A screw-type terminal
max. load 80 mA strips, max. 1.5 mm²
PCR-410: 1 relay with N.O. Protective rating Housing: IP 20
contact, 8 A, 230 V AC, front panel: IP 52,
resistive load protection class 2

(kg)
W H D
PCR-300 70 85 61 approx. 0.42
PCR-310 70 32 74
approx. 0.52
Transformer 52 47 34
PCR-410 70 32 74
approx. 0.52
Transformer 52 47 34
PCR-300RC 70 85 61 approx. 0.42
Installation
 4 DIN standard modular housing:
 Open out the side mounting tabs
 Clip the unit on to 35 mm rail
 press tabs in again

PCR-300
PCR-300RC
Alarm only PCR-410
PCR-310
PCR-410

Series PTI-610
ELECTRONIC TEMPERATURE DISPLAY
PRODUCT DATA
Features
 Display for °C and °F selectable
 Snap-in installation for aperture 28.5 x 70.5 mm
 Retaining frame for wall thickness up to 22 mm
 PTC sensors with stainless steel sleeves
 Electronic sensor-line up, if required
 Mains transformer integrated
Specification
Power supply 230 V, ±10 %, 50/60 Hz
Display 3-digit, 7-segment, LED red,
height 14.2 mm
Resolution 1K
-67 °F to +99 °F
Input analogue input for PTC sensor
Sensor PTC sensor, cable length 2.5 m,
accuracy ±2 %
Application range of use:
PTI-610 is an electronic temperature display for general -30 °C to +80 °C cable not fixed
purpose use. -40 °C to +80 °C cable fixed
The display does have snap-in housing for installation in a Ambient in operation:
control panel. temperature/humidity 0° to + 50 °C,
30 to 85 % R.H. excluding dew
Material in storage:
Housing ABS-plastic, self-extinguishing -20 °C to +80 °C
Connectors 10 A screw-type terminal strips,
max. 1.5 mm
Protective rating Housing: IP 20
front panel: IP 52,
protection class 2

Series PTI-610

(kg)
W H D
PTI-610 70 32 74 approx. 0.27
Installation

Series AMV
AUTOMATIC EXPANSION VALVES
INTERCHANGEABLE ORIFICE CARTRIDGE, ADJUSTABLE EVAPORATING PRESSURE
PRODUCT DATA
Features
 AMV : with internal pressure equalisation; for single
injection in installations with one or more cooling
circuits
 AMVX: with external pressure equalisation; for optimal
evaporation effectiveness in all applications.
Obligatory for multiple injection by liquid distributors
 Adjustable evaporating pressure setting ± 0.5 bar
within the evaporating pressure range
 Flare connections
 Extreme durable due to stainless steel head and
stainless steel diaphragm welded using protective gas
AMV  Interchangeable orifice cartridges
 Refrigerants: all CFC, HCFC, HFC
HFO (e.g. R1234yf) and future Blends
not for ammonia
Specification
Nominal capacity range 0.52 to 22.4 kW R22
(small orifice graduation for
AMVX optimal control behaviour,
interchangeable orifice
cartridges)
Evaporating pressure range see table on page 38
Application Maximum pressure PS 29.0 bar(a)
Automatic expansion valves (constant pressure valves) series Maximum test pressure PF 31.9 bar(a)
AMV are used in general refrigeration and for original Max. ambient temperature 100 °C
equipment.
For plants like dehumidifiers, air driers, water coolers,
ice-making machines or air conditioners.
Materials
Body brass
Thermal head stainless steel
Connection brass

Series AMV
Evaporating pressure
1. Automatic expansion valves with internal pressure equalisation 2. Automatic expansion valves with external pressure equalisation
Type OS number Evaporating Type OS number Evaporating

pressure range pressure range
AMV-00001 1.5 – 2.5 bar AMVX-00001 1.5 – 2.5 bar
AMV-00002 2.5 – 3.5 bar AMVX-00002 2.5 – 3.5 bar
AMV AMVX
AMV-00003 3.5 – 4.5 bar AMVX-00003 3.5 – 4.5 bar
AMV-00004 4.5 – 5.5 bar AMVX-00004 4.5 – 5.5 bar
Capacities
Nominal capacity (kW)*
Type Orifice size
R134a R22 R407C R422D R404A R507A R410A
0.3 0.36 0.52 0.50 0.36 0.36 0.36 0.62
0.5 0.69 0.99 0.95 0.67 0.68 0.69 1.2
0.7 1.0 1.4 1.3 0.92 0.97 0.98 1.6
1.0 1.4 2.0 1.9 1.3 1.4 1.4 2.4
1.5 2.2 3.2 3.1 2.2 2.2 2.3 3.8
AMV
2.0 2.9 4.0 3.9 2.7 2.8 2.9 4.8
AMVX
2.5 4.0 5.8 5.6 3.9 4.1 4.1 6.9
3.0 6.6 9.3 8.9 6.3 6.5 6.6 11.1
3.5 8.7 12.2 11.7 8.3 8.6 8.7 14.6
4.5 11.8 17.0 16.4 11.3 12.0 12.1 20.3
4.75 15.9 22.4 21.6 15.3 15.8 15.9 26.8
* Capacities are based on to= +4 °C, tc = +38 °C and 1 K subcooled liquid refrigerant entering the valve.
For other operating conditions see capacity charts in Honeywell catalogue or consult the Honeywell software.

Type Connections Weight
Inlet Outlet Pressure (kg)
(B) (A) equaliser (C)
AMV 5/8" UNF 3/4" UNF - approx. 0.35
AMVX 5/8" UNF 3/4" UNF 7/16" UNF approx. 0.36

AMV / AMVX VD
Type Code / Order Information (Part Programme)

1. Valve body
AMV X BM 3.0 5/8" UNF x 3/4" UNF

Series
Pressure equalisation:
X = external
() = internal
Range middle
evaporating pressure range (bar)
Connection size
(inlet x outlet)
2. Orifice cartridge
VD 0.5
Series
Orifice size

Series AMV
Installation Evaporating pressure Adjustment

 The valves may be installed in any position. The evaporating pressure setting can be adjusted by
 The external pressure equaliser line should be 6 mm or 1/4” ± 0.5 bar around the range middle of the evaporating
in diameter. An overbow is recommended in order to prevent pressure range.
the ingress of oil into the equaliser line.
Turning clockwise = reduced evaporating pressure
warmer than 100 °C. Turning
= increased evaporating pressure
counterclockwise
 When tightening flare nuts of the flare connections grip at
wrench flats on the valve body.
Special Accessory:
Adapter series LA for solder connection at the inlet for 6 mm,
10 mm, 1/4” and 3/8”.

Series AEL
AUTOMATIC EXPANSION VALVES
FIXED ORIFICE, ADJUSTABLE EVAPORATING PRESSURE
PRODUCT DATA
Features
 Smallest dimensions
 High performance
 Hermetic construction
 Wide evaporating pressure range
 Adjustable evaporating pressure setting
 Solder connections
 Internal pressure equalisation
 Fixed orifice
 Bypass on request
not for ammonia
Specification
Evaporating pressure range 1 - 7 bar(a)
Factory setting for
evaporating pressure 2.2 bar(a)
Application Maximum pressure PS 25.5 bar(a)
Automatic expansion valves (constant pressure valves) series Maximum test pressure PF 28 bar(a)
AEL are used in general refrigeration and for original Max. ambient temperature 100 °C
equipment.
For plants with single injected evaporators and without a Installation
distributor, such as air conditioners, dehumidifiers, air driers,
water coolers or ice-making machines.  The valves may be installed in any position.
Materials warmer than 100 °C.
Body brass  Remove plastic cap during soldering
Head stainless steel, brass  Constructive modifications at the valve are not allowed.
Connection tubes copper

Adjustment
One complete revolution of the adjusting screw effects an
alternation of the evaporating pressure by approx. 0.8 bar.
Turning clockwise = Higher evaporation pressure

Turning
= Lower evaporation pressure
counterclockwise

Series AEL
Capacities
Type Valve size Orifice Nominal capacity (kW)*
size R22 R134a R404A R507A
0.5 0.7 1.4 1.0 0.97 0.98
1.0 1.0 2.0 1.4 1.4 1.4
2.0 2.0 4.0 2.9 2.8 2.9
AEL 3.0 3.0 9.3 6.6 6.5 6.6
4.0 3.5 12.2 8.7 8.6 8.7
5 4.75 22.4 15.9 15.8 15.9
6 5 29.1 20.0 20.5 20.7
* Capacities are based on to = +4 °C, tc = +38 °C and 1 K subcooled liquid refrigerant entering the valve.

Type Valve Connections Dimensions (mm) Weight (kg)
size
Inlet (A) Outlet (B) C D E F
0.5
1.0 6 mm ODF 10 mm ODF
2.0 58 36 106 54 approx. 0.16
3.0
AEL 1/4" ODF 3/8" ODF
4.0
5 3/8" ODF 5/8" ODF
10 mm ODF 16 mm ODF 64 47 122 69 approx. 0.28
6
3/8" ODF 5/8" ODF

Series TMV
THERMOSTATIC EXPANSION VALVES
INTERCHANGEABLE ORIFICE CARTRIDGE
PRODUCT DATA
Features
 TMV / TMVBL: with internal pressure equalisation; for
single injection in installations with one or more
cooling circuits
 TMVX / TMVXBL: with external pressure equalisation;
for optimal evaporation effectiveness in all
applications. Obligatory for multiple injection by liquid
distributors
 Combi adsorber charge
 The same valve can be used for different
refrigerants (see table on page 44)
  Controller charge is high sensitive and responsive
TMVX thus lowest possible level of superheat can be
achieved
 Charge is not sensitive to effects of temperature on
the capillary tube and valve head
 Damping characteristic results in stable control
behaviour
 Suitable for systems with hot gas defrosting
 Adjustable superheat setting
 Flare connections: TMV, TMVX
TMVXBL
 Flare / solder connections: TMVBL, TMVXBL
Application
 Interchangeable orifice cartridges
Thermostatic expansion valves series TMV are used in
general refrigeration and for original equipment.  Refrigerants: R134a, R401A
R22, R407C, R407A, R422D
Plants with one or more circuits such as refrigerated cabinets
   R404A, R507A, R402A, R407B
even with cramped mounting conditions, ice and cream
R410A. R407F
machines, milk cooling units, water chillers, vehicle air
conditioning systems, cold stores, and air conditioning
Further refrigerants on request.
systems.
Specification
Materials Nominal capacity range 0.52 to 22.4 kW R22
Body brass optimal control behaviour,
Thermal head stainless steel interchangeable orifice
cartridges)
Connection solder: copper
flare: brass Evaporating temperature see table on page 44
range
Maximum pressure PS see table on page 44
Maximum test pressure PF see table on page 44
Max. ambient temperature 100 °C
Max. bulb temperature 140 °C
Static superheat approx. 3 K
Length of capillary tube 1.5 m
Bulb diameter 12 mm

Series TMV
Thermal Charges and Temperature Ranges

1. Adsorber charge 2. Adsorber charge with pressure limiting performance MOP
Refrigerant Evaporation PS PF Refri- Evaporation MOP PS PF

temperature (bar(a)) (bar(a)) gerant temperature (bar(a)) (bar(a))
range range
R134a, R401A +15 °C to -30 °C 34 37.4 R134a, +5 °C to -30 °C MOP A +15 °C 34 37.4
R401A
R22, R407C, +15 °C to -45 °C 36 39.6 -10 °C to -30 °C MOP A ±0 °C 29 31.9
R407A, R422D R22, +5 °C to –45 °C MOP A +15 °C 36 39.6
R404A, R507A, ±0 °C to -50 °C 36 39.6 R407C,
-10 °C to -45 °C MOP A ±0 °C 29 31.9
R402A, R407B R407A,
+15 °C to -30 °C 36 39.6 R422D -27 °C to -45 °C MOP A -18 °C 29 31.9
R407C +15 °C to -30 °C 36 39.6 R404A, -10 °C to -50 °C MOP A ±0 °C 36 39.6
R407F ±0 °C to -45 °C 36 39.6 R507A,
-20 °C to -50 °C MOP A -10 °C 34 37.4
R402A,
R410A +15 °C to -20 °C 40 44 R407B -27 °C to -50 °C MOP A -18 °C 34 37.4
Further refrigerants on request. R407F 27 °C to -45 °C MOP A -18 °C 29 31.9
Thermal systems with adsorber charge are completely
Further refrigerants and MOP on request.
insensitive to effects of temperature on the capillary tube and
valve head. It reacts only according to the temperature of the
bulb.
Thus, Honeywell TMV valves with combi adsorber charge
work absolutely reliable, even in icy condition or while
defrosting using hot gas.
Capacities
Type Orifice size
R134a R22 R407C R407F R404A R507A R410A
0.3 0.36 0.52 0.50 0.56 0.36 0.36 0.62
0.5 0.69 0.99 0.95 1.1 0.68 0.69 1.2
0.7 1.0 1.4 1.3 1.5 0.97 0.98 1.6
1.0 1.4 2.0 1.9 2.2 1.4 1.4 2.4
TMV
1.5 2.2 3.2 3.1 3.5 2.2 2.3 3.8
TMVX
2.0 2.9 4.0 3.9 4.3 2.8 2.9 4.8
TMVBL
2.5 4.0 5.8 5.6 6.3 4.1 4.1 6.9
TMVXBL
3.0 6.6 9.3 8.9 10.1 6.5 6.6 11.1
3.5 8.7 12.2 11.7 13.2 8.6 8.7 14.6
4.5 11.8 17.0 16.4 18.5 12.0 12.1 20.3
4.75 15.9 22.4 21.6 24.3 15.8 15.9 26.8

(kg)
Inlet Outlet Pressure
(B) (A) equaliser (C)
TMV 5/8" UNF 3/4" UNF - approx. 0.35
TMVX 5/8" UNF 3/4" UNF 7/16" UNF approx. 0.36
5/8" UNF 12 mm ODF -
TMVBL approx. 0.33
5/8" UNF 1/2" ODF -
5/8" UNF 12 mm ODF 6 mm ODF
TMVXBL approx. 0.34
5/8" UNF 1/2" ODF 1/4" ODF

TMV / TMVX
TMVBL / TMVXBL VD

1. Valve body
TMV X BL R134a MOP A +15 °C 5/8" UNF x 1/2" ODF

Series
X = external
() = internal
BL = flare x solder connection
() = flare connection
Refrigerant
Adsorber charge with MOP
() = without MOP
Connection size
(inlet x outlet)
2. Orifice cartridge
VD 0.5
Series
Orifice size

Series TMV
Installation Superheat Adjustment

 The valves may be installed in any position. In general the Honeywell valves should be installed with the
 The external pressure equaliser line should be 6 mm or factory setting for the used refrigerant unaltered.
1/4” in diameter and is to be connected downstream of the At combi adsorber valves the label on the capillary tube
remote bulb. An overbow is recommended in order to indicates how to adjust the adjusting spindle (with arrow for
prevent the ingress of oil into the equaliser line. direction), depending on the refrigerant used. This correction
of the adjustment is essential to ensure that the control
 The bulb should preferably be positioned on the upper half performance of the valve is correct. The refrigerant used must
of a horizontal suction line but never after a liquid trap. be marked on the label.
As a general rule, bulbs of expansion valves should be
insulated to prevent them being affected by the ambient This superheat adjustment is calibrated for lowest
temperature. superheating and optimum evaporator utilisation. However,
should it be necessary to adjust the superheat, turn the
 Do not bend or squeeze the bulb when tightening the bulb adjusting spindle as follows:
clamp!
 When soldering the valve, the valve body must not get Turning clockwise reduced refrigerant mass flow,
=
warmer than 100 °C. increase of superheat
 When tightening flare nuts of the flare connections grip at Turning increased refrigerant mass
=
wrench flats on the valve body. counterclockwise flow, decrease of superheat
 Constructive modifications at the valve are not allowed. One turn of adjusting spindle alters superheat setting by
approx. 0.55 bar. Increase of superheat setting results in a
lower MOP-value and vice versa.
Special Accessory:
Adapter series LA for solder connection at the inlet for 6 mm,
10 mm, 1/4”, 3/8”.

Series TMVL
INTERCHANGEABLE ORIFICE CARTRIDGE, SEPARATE SOLDER BASE
PRODUCT DATA
Features
 Only one valve body necessary for internal and
external pressure equalisation. Connection for
pressure coupler is integrated in the solder base.
 TMVL: Valve body and solder base with internal
pressure equalisation; for single injection in
installations with one or more cooling circuits.
 TMVLX: Valve body and solder base with external
pressure equalisation; for optimal evaporation
effectiveness in all applications. Obligatory for
multiple injection by liquid distributors.
 Combi adsorber charge
 Controller charge is high sensitive and responsive
thus lowest possible level of superheat can be
achieved
TMVLX-W
 Damping characteristic results in stable control
behaviour
 Suitable for systems with hot gas defrosting
TMVLX-D  Adjustable superheat setting
 Solder base available in two-way construction and in
Application angle construction
Thermostatic expansion valves series TMVL are used in  Extreme durable due to stainless steel head and
general refrigeration and for original equipment. stainless steel diaphragm welded using protective gas
Plants with one or more refrigerant circuits such as  Interchangeable orifice cartridges
refrigerated cabinets even with cramped mounting conditions,
ice and cream machines, milk cooling systems, cold stores,  Refrigerants: R134a, R401A
air conditioning systems and heat pumps. R22, R407C, R407A, R422D
R404A, R507A, R402A, R407B
  R124, R227, R410A, R236fa, R407F
Materials   Further refrigerants on request.
Body brass
Specification
optimal control behaviour, inter-
changeable orifice cartridges)
Evaporating temp. range see table on page 48
Bulb diameter 12 mm

Series TMVL

1. Adsorber charge 2. Adsorber charge with pressure limiting performance MOP
Refrigerant Evaporation PS PF Refri- Evaporation MOP PS PF

temperature range (bar(a)) (bar(a)) gerant temperature (bar(a)) (bar(a))
range
R134a, R401A +15 °C to -30 °C 34 37.4
R134a, +5 °C to -30 °C MOP A +15 °C 34 37.4
R22, R407C, +15 °C to -45 °C 36 39.6
R401A
R407A, R422D -10 °C to -30 °C MOP A ±0 °C 29 31.9
R404A, R507A, ±0 °C to -50 °C 36 39.6 R22, +5 °C to -45 °C MOP A +15 °C 36 39.6
R402A, R407B R407C,
+15 °C to -30 °C 36 39.6 -10 °C to -45 °C MOP A ±0 °C 29 31.9
R407A,
R124 +20 °C to -30 °C 29 31.9 R422D -27 °C to -45 °C MOP A -18 °C 29 31.9
R227 +20 °C to -30 °C 29 31.9 R404A, -10 °C to -50 °C MOP A ±0 °C 36 39.6
R236fa +30 °C to -10 °C 29 31.9 R507A,
-20 °C to -50 °C MOP A -10 °C 34 37.4
R402A,
R407C +15 °C to -30 °C 36 39.6 R407B -27 °C to -50 °C MOP A -18 °C 34 37.4
R410A +15 °C to -20 °C 40 44 R407F -27 °C to -45 °C MOP A -18 °C 29 31.9
R407F ±0 °C to -45 °C 36 39.6 Further refrigerants and MOP on request.
bulb.
Thus, Honeywell TMVL valves with combi adsorber charge
Capacities
Type Orifice size
R134a R22 R407C R407F R404A R507A R410A
0.3 0.36 0.52 0.50 0.56 0.36 0.36 0.62
0.5 0.69 0.99 0.95 1.1 0.68 0.69 1.2
0.7 1.0 1.4 1.3 1.5 0.97 0.98 1.6
1.0 1.4 2.0 1.9 2.2 1.4 1.4 2.4
1.5 2.2 3.2 3.1 3.5 2.2 2.3 3.8
TMVL 2.0 2.9 4.0 3.9 4.3 2.8 2.9 4.8
2.5 4.0 5.8 5.6 6.3 4.1 4.1 6.9
3.0 6.6 9.3 8.9 10.1 6.5 6.6 11.1
3.5 8.7 12.2 11.7 13.2 8.6 8.7 14.6
4.5 11.8 17.0 16.4 18.5 12.0 12.1 20.3
4.75 15.9 22.4 21.6 24.3 15.8 15.9 26.8

(kg)
(A) (B) equaliser (C)
TMVL - - - approx. 0.43
6 mm ODF 10 mm ODF -
1/4" ODF 3/8" ODF -
VLS 10 mm ODF 12 mm ODF -
approx. 0.16
angle construction 3/8" ODF 1/2" ODF -
1/2" ODF 5/8" ODF -
6 mm ODF 10 mm ODF 6 mm ODF
1/4" ODF 3/8" ODF 1/4" ODF
VLSX 10 mm ODF 12 mm ODF 6 mm ODF
approx. 0.17
angle construction 3/8" ODF 1/2" ODF 1/4" ODF
1/2" ODF 5/8" ODF 1/4" ODF
VLS 3/8" ODF 1/2" ODF -
approx. 0.16
two-way construction 12 mm ODF 16 mm ODF -
1/2" ODF 5/8" ODF -
VLSX 3/8" ODF 1/2" ODF 1/4" ODF
approx. 0.17
two-way construction 12 mm ODF 16 mm ODF 6 mm ODF
1/2" ODF 5/8" ODF 1/4" ODF
TMVL
VD VLS(X) – two-way VLS(X) - angle

Series TMVL

1. Valve body
TMVL R22 MOP A -18 °C

Series
Refrigerant
Adsorber charge with MOP
() = without MOP
2. Solder base 3. Orifice cartridge
10 mm x VD 0.5
VLS X W
12 mm Series
Series Orifice size
X = external
() = internal
Solder connection ODF
(inlet x outlet)
D = two-way construction
W = angle construction

1/4" in diameter and is to be connected downstream of the At combi adsorber valves the label on the capillary tube
remote bulb. An overbow is recommended in order to indicates how to adjust the adjusting spindle (with arrow for
prevent the ingress of oil into the equaliser line. direction), depending on the refrigerant used. This correction
 The bulb should preferably be positioned on the upper performance of the valve is correct. The refrigerant used must
half of a horizontal suction line but never after a liquid be marked on the label.
trap. As a general rule, bulbs of expansion valves should
be insulated to prevent them being affected by the This superheat adjustment is calibrated for lowest
ambient temperature. superheating and optimum evaporator utilisation. However,
 Do not bend or squeeze the bulb when tightening the bulb adjusting spindle as follows:
clamp!
 The screws fixing the valve body to the solder base must Turning clockwise reduced refrigerant mass flow,
=
be tightened in diagonal sequence (torque 12+1 Nm). increase of superheat
 Constructive modifications at the valve are not allowed. Turning increased refrigerant mass
=
counterclockwise flow, decrease of superheat
 Never quench the solder base with water after soldering,
this may cause cracks and distort the sealing surfaces. One turn of adjusting spindle alters superheat setting by

Series TMX
INTERCHANGEABLE ORIFICE CARTRIDGE, BALANCED PORT
PRODUCT DATA
Features
 TMXL: TMX and solder base, two-way construction or
angle construction
 TMXB: TMX and flare base, two way construction
 Damped gas charge with pressure limiting MOP
 Liquid charge
 Solder connections or flare connections
 External pressure equalisation is integrated in the
valve body
 Balanced port construction
TMXB  Interchangeable orifice cartridges
 Refrigerants: R22, R23, R134a, R227, R236fa,
R401A, R404A, R407C, R410A, R422D,
R507A, R508B, ISC89, R407F
TMXL
Specification
Application
Evaporating temperature
Thermostatic expansion valves series TMX are used in range see table on page 52
general refrigeration and for original equipment.
Plants with one or more refrigerant circuits such as
refrigerated cabinets, deep freezing plants, milk cooling units, Maximum test pressure PF see table on page 52
water chillers, air conditioning systems, cold stores and heat Max. ambient temperature 100 °C
pumps. For plants with single and multiple injections, with Max. bulb temperature gas charge: 140 °C
high or low flow resistance, for all kind of distributors. liquid charge: 70 °C
Static superheat approx. 3.5 K
Length of capillary tube 2m
Materials Bulb diameter 16 mm
Body brass
Base brass

Series TMX

1. Gas charge with pressure limiting MOP
Refri- Evaporation MOP PS PF Refri- Evaporation MOP PS PF

gerant temperature (bar(a)) (bar(a)) gerant temperature (bar(a)) (bar(a))
range range
Commercial refrigerants Deep freeze refrigerants
R22 +15 °C to -45 °C MOP +15 °C 36 39.6 R23 -40 °C to -80 °C MOP -40 °C 29 31.9
+10 °C to -45 °C MOP +10 °C 36 39.6 -55 °C to -80 °C MOP -55 °C 29 31.9
±0 °C to -45 °C MOP ±0 °C 29 31.9 R410A -40 °C to -70 °C MOP -40 °C 29 31.9
-10 °C to -45 °C MOP -10 °C 29 31.9 R508B -55 °C to -100 °C MOP -55 °C 29 31.9
-18 °C to -45 °C MOP -18 °C 29 31.9 Isceon 89 -40 °C to -70 °C MOP -40 °C 29 31.9
R134a +25 °C to -40 °C MOP +25 °C 34 37.4 Further refrigerants and MOP on request.
+20 °C to -40 °C MOP +20 °C 34 37.4 MOP valves protect the compressor by limiting the increase
+15 °C to -40 °C MOP +15 °C 34 37.4 of suction pressure.
The MOP value should be chosen for the max. permissible
+10 °C to -40 °C MOP +10 °C 34 37.4
suction pressure of the compressor or min. 5 K higher than
±0 °C to -40 °C MOP ±0 °C 29 31.9 the required evaporating temperature of the system.
R401A +10 °C to -40 °C MOP +10 °C 34 37.4 For orders without any MOP indication a valve with MOP
R404A +10 °C to -50 °C MOP +10 °C 36 39.6 + 10 C will be delivered.
±0 °C to -50 °C MOP ±0 °C 36 39.6 With gas charged valves and MOP it is under all operating
conditions necessary that the bulb is always colder than the
-10 °C to -50 °C MOP -10 °C 34 37.4
capillary tube and the thermal head!
-18 °C to -50 °C MOP -18 °C 34 37.4 With the Honeywell TMX series the thermal head is heated
-30 °C to -50 °C MOP -30 °C 29 31.9 advantageously by the liquid refrigerant. The warm thermal
R407C +15 °C to -30 °C MOP +15 °C 36 39.6 head is on the safe side at any time.
+10 °C to -30 °C MOP +10 °C 36 39.6 2. Flüssigfüllung
±0 °C to -30 °C MOP ±0 °C 29 31.9 Refrigerant Evaporation PS PF
R410A +15 °C to -50 °C MOP +15 °C 40 44.0 temperature range (bar(a)) (bar(a))
-10 °C to -50 °C MOP -10 °C 29 31.9 R22 +30 °C to -45 °C 36 39.6
-15 °C to -50 °C MOP -15 °C 29 31.9
R134a +20 °C to -40 °C 34 37.4
-20 °C to -50 °C MOP -20 °C 29 31.9
R227 +40 °C to -10 °C 29 31.9
R422D +15 °C to -45 °C MOP +15 °C 36 39.6
-18 °C to -45 °C MOP -18 °C 29 31.9 R236fa +30 °C to -10 °C 29 31.9
R507A +10 °C to -50 °C MOP +10 °C 36 39.6 R404A +10 °C to -50 °C 36 39.6
±0 °C to -50 °C MOP ±0 °C 36 39.6 R407C +30 °C to -30 °C 36 39.6
-18 °C to -50 °C MOP -18 °C 34 37.4 Further refrigerants on request.
R407F +10 °C to -45 °C MOP +10 °C 36 39.6
-18 °C to -45 °C MOP -18 °C 29 31.9
Capacities
Nominal capacitiy (kW)*
Type Orifice size
R22 R134a R404A R407C R407F R410A R507A R124 R227 R236fa
4.5 17.0 11.8 12.0 16.4 18.5 20.3 12.1 9.4 6.6 6.0
TMXL 4.75 22.4 15.9 15.8 21.6 24.3 26.8 15.9 12.4 8.7 8.0
5 29.1 20.0 20.5 28.0 31.6 34.8 20.7 16.1 11.3 10.3
and 6 42.4 27.6 29.8 40.8 46.0 50.8 30.1 23.5 16.4 15.1
7 54.5 35.3 38.3 52.5 59.1 65.3 38.7 30.2 21.1 19.4
TMXB 8 64.1 43.3 45.1 61.8 69.6 76.9 45.6 35.6 24.9 22.8
10 75.1 51.0 52.8 72.3 81.5 90.0 53.3 41.7 29.1 26.7
For refrigerant R124, R227 and 236fa: Capacities are based on to = +10 °C, tc = +50 °C and 1 K subcooled liquid
refrigerant entering the valve.

(kg)
(A) + (B) (C) + (D) equaliser
TMX - - 7/16" UNF approx. 0.60
XD - - - approx. 0.14
XLS 12 + 16 mm ODF 16 + 22 mm ODF -
approx. 0.41
two-way construction 1/2" + 5/8" ODF 5/8" + 7/8" ODF -
XLS 12 + 16 mm ODF 16 + 22 mm ODF -
approx. 0.32
angle construction 1/2" + 5/8" ODF 5/8" + 7/8" ODF -
XBS
7/8" UNF 7/8" UNF - approx. 0.49
two-way construction
TMX
XD XBS – two-way
XLS - angle XLS – two-way

Series TMX

1. Valve body
TMX R134a MOP +10 °C

Series
Refrigerant
Pressure limiting MOP
() = without MOP
2. Solder / Flare base 3. Orifice cartridge
16 mm x XD 10
XLS W
22 mm Series
Series Orifice size
XLS = solder connection
XBS = flare connection
Connection size

1/4” in diameter and is to be connected downstream of the This superheat adjustment is calibrated for lowest
remote bulb. An overbow is recommended in order to superheating and optimum evaporator utilisation. However,
prevent the ingress of oil into the equaliser line. should it be necessary to adjust the superheat, turn the
adjusting spindle as follows:
 The bulb should preferably be positioned on the upper
half of a horizontal suction line but never after a liquid Turning clockwise reduced refrigerant mass flow,
trap. As a general rule, bulbs of expansion valves should =
increase of superheat
be insulated to prevent them being affected by the
ambient temperature. Turning increased refrigerant mass
=
 Do not bend or squeeze the bulb when tightening the bulb
clamp! One turn of adjusting spindle alters superheat setting by
 Never quench the base with water after soldering, approx. 0.3 bar. Increase of superheat setting results in a
this may cause cracks and distort the sealing surfaces. lower MOP-value and vice versa.
 The screws fixing the valve body to the solder base must
+1
be tightened in diagonal sequence (torque 16 Nm).

Series TLK
FIXED ORIFICE, FIXED SUPERHEAT SETTING
PRODUCT DATA
Features
 Gas charge with MOP for quick response time adapted
to small evaporators
 Wide evaporating temperature range
 Fixed superheat setting
 Warm thermal head provides best reliability
 Fixed orifice
 Bypass on request
 Refrigerants: R134a, R22, R404A, R407C, R507A
  Further refrigerants on request.
Specification
range see table on page 56
Application Maximum test pressure PF see table on page 56
Thermostatic expansion valves series TLK are used for serial Max. ambient temperature 100 °C
produced systems such as drink dispensers, beer coolers, ice Max. bulb temperature 140 °C
cream machines, milk cooling units, water chillers and vehicle Static superheat approx. 4 K
air conditioning systems. For single injected evaporators.
Length of capillary tube 1m
Bulb diameter 12 mm
Materials
Body brass

Series TLK

1. Gas charge with pressure limiting MOP
MOP valves protect the compressor by limiting the increase
Refri- Evaporation MOP PS PF
of suction pressure.
gerant temperature (bar(a)) (bar(a))
range The MOP value should be chosen for the max. permissible
suction pressure of the compressor or min. 5 K higher than
R134a +15 °C to -40 °C MOP +15 °C 34 37.4 the required evaporating temperature of the system.
+10 °C to -40 °C MOP +10 °C 34 37.4 For orders without any MOP indication a valve with MOP
+ 10°C will be delivered.
±0 °C to -40 °C MOP ±0 °C 29 31.9
With gas charged valves and MOP it is under all operating
R22 +15 °C to -45 °C MOP +15 °C 36 39.6 conditions necessary that the bulb is always colder than the
+10 °C to -45 °C MOP +10 °C 36 39.6 capillary tube and the thermal head!
With the Honeywell TLK series the thermal head is heated
± 0 °C to -45 °C MOP ±0 °C 29 31.9 advantageously by the liquid refrigerant. The warm thermal
-18 °C to -45 °C MOP -18 °C 29 31.9 head is on the safe side at any time.
R404A +10 °C to -50 °C MOP +10 °C 36 39.6
±0 °C to -50 °C MOP ±0 °C 36 39.6
-18 °C to -50 °C MOP -18 °C 34 37.4
R407C +15 °C to -30 °C MOP +15 °C 36 39.6
+10 °C to -30 °C MOP +10 °C 36 39.6
R507A +10 °C bis -50 °C MOP +10 °C 36 39.6
Capacities
Type Orifice size
R134a R22 R404A R407C R507A
0.3 0.36 0.52 0.36 0.50 0.36
0.5 0.69 0.99 0.68 0.95 0.69
0.7 1.0 1.4 0.97 1.3 0.98
TLK
1.0 1.4 2.0 1.4 1.9 1.4
1.5 2.2 3.2 2.2 3.1 2.3
2.0 2.9 4.0 2.8 3.9 2.9

Type Orifice Connections Weight
size (kg)
Inlet Outlet
(A) (B)
0.3
0.5 6 mm ODF 10 mm ODF
0.7 approx. 0.18

TLK 1.0 1/4" ODF 3/8" ODF
1.5
10 mm ODF 12 mm ODF
2.0 approx. 0.19
3/8" ODF 1/2" ODF

TLK

TLK 0.5 R22 MOP +10 °C 6 mm x 10 mm
Series
Orifice size
Refrigerant
Gas charge with MOP
(inlet x outlet)
Installation
 The valves may be installed in any position. Information for original equipment manufacturers:
 The bulb should preferably be positioned on the upper half The valve series TLK can be customised to the
of a horizontal suction line but never after a liquid trap. As requirements of your series device in an optimum way.
a general rule, bulbs of expansion valves should be Contact us!
insulated to prevent them being affected by the ambient
temperature.
 In case of ice formation at the mounting site of the bulb,
we advise to use a bulb clamp instead of clips.
 Do not bend or squeeze the bulb!

Series TLE
FIXED ORIFICE, ADJUSTABLE SUPERHEAT SETTING
PRODUCT DATA
Features
 TLE: with internal pressure equalisation; for single
circuits.
 TLEX: with external pressure equalisation; for optimal
Obligatory for multiple injection by liquid distributors.
 Combi adsorber charge as standard
achieved
TLE  Charge is not sensitive to effects of temperature on
 damping characteristic results in stable control
behaviour
 Gas charge for deep freeze applications
TLEX
Application  Fixed orifice
Thermostatic expansion valves series TLE and TLEX are  Refrigerants: R134a, R401A
used in plants with one or more refrigerant circuits, in R22, R407C, R407A, R422D
particular for series systems such as heat pumps, refrigerated R404A, R507A, R402A, R407B
cabinets, deep freeze chests, freezers, fermentation R410A
interrupters, ice and cream machines, compact systems in R23, ISC 89, R508A, R508B
refrigeration and air conditioning. HFO (e.g. R1234yf) and future Blends
Materials
Specification
Body brass
Thermal head Nominal capacity range 0.99 to 17.0 kW R22
stainless steel
Connection tubes copper optimal control behaviour)
Bulb diameter 12 mm

Series TLE

1. Adsorber charge 3. Gas charge
Refrigerant Evaporation PS PF Refrige Evaporation MOP PS PF

temperature range (bar(a)) (bar(a)) rant temperature (bar(a)) (bar(a))
range
R134a, R401A +15 °C to -30 °C 34 37.4
ISC 89 -40 °C to -70 °C MOP -40 °C 29 31.9
R22, R407C, +15 °C to -45 °C 36 39.6
R407A, R422D -55 °C to -70 °C MOP -55 °C 29 31.9
R404A, R507A, ±0 °C to -50 °C 36 39.6 R23 -40 °C to -80 °C MOP -40 °C 29 31.9
R402A, R407B -55 °C to -80 °C MOP -55 °C 29 31.9
R410A +15 °C to -20 °C 40 44.0 R407C +10 °C to -30 °C MOP +10 °C 36 39.6
Further refrigerants on request. R410A +15 °C to -50 °C MOP +15 °C 40 44.0
R508A -40 °C to -90 °C MOP -40 °C 29 31.9
valve head. It reacts only according to the temperature of the -55 °C to -90 °C MOP -55 °C 29 31.9
bulb.
R508B -40 °C to -100 °C MOP -40 °C 29 31.9
Thus, Honeywell TLE and TLEX valves with combi adsorber
charge work absolutely reliable, even in icy condition or while -55 °C to -100 °C MOP -55 °C 29 31.9
defrosting using hot gas. Further refrigerants and MOP on request.
2. Adsorber charge with pressure limiting performance (MOP) conditions necessary that the bulb is always colder than the
Refri- Evaporation MOP PS PF With the Honeywell TLE and TLEX series the thermal head is
gerant temperature (bar(a)) (bar(a)) heated advantageously by the liquid refrigerant. The warm
range thermal head is on the safe side at any time.
R134a, +5 °C to -30 °C MOP A +15 °C 34 37.4
R401A
-10 °C to -30 °C MOP A ±0 °C 29 31.9
R22, +5 °C to -45 °C MOP A +15 °C 36 39.6
R407C,
-10 °C to -45 °C MOP A ±0 °C 29 31.9
R407A,
R422D -27 °C to -45 °C MOP A -18 °C 29 31.9
R404A, -10 °C to -50 °C MOP A ±0 °C 36 39.6
R507A,
-20 °C to -50 °C MOP A -10 °C 34 37.4
R402A,
R407B, -27 °C to -50 °C MOP A -18 °C 34 37.4
Capacities
Type Orifice size
R134a R22 R407C R410A R404A R507A
0.5 0.69 0.99 0.95 1.2 0.68 0.69
0.7 1.0 1.4 1.3 1.6 0.97 0.98
1.0 1.4 2.0 1.9 2.4 1.4 1.4
1.5 2.2 3.2 3.1 3.8 2.2 2.3
TLE
2.0 2.9 4.0 3.9 4.8 2.8 2.9
TLEX
2.5 4.0 5.8 5.6 6.9 4.1 4.1
3.0 6.6 9.3 8.9 11.1 6.5 6.6
3.5 8.7 12.2 11.7 14.6 8.6 8.7
4.5 11.8 17.0 16.4 20.3 12.0 12.1

Type Orifice Connections Weight
size (kg)
(A) (B) equaliser (C)
0.5 6 mm ODF 12 mm ODF 6 mm ODF
0.7
1.0 1/4" ODF 1/2" ODF 1/4" ODF
1.5
2.0 10 mm ODF 12 mm ODF 6 mm ODF
TLE 2.5
approx. 0.32
TLEX 3.0
3/8" ODF 1/2" ODF 1/4" ODF
3.5
3/8" ODF 5/8" ODF 1/4" ODF
4.5
1/2" ODF 5/8" ODF 1/4" ODF
TLE 0.5 – 4.5 TLEX 0.5 – 4.5

TLE X 0.7 R22 MOP A -18 °C 3/8“ x 1/2“
Series
X = external
() = internal
Orifice size
Refrigerant
Charge type, MOP,
evaporation temperature range
(inlet x outlet)

Series TLE

 The external pressure equaliser line (TLEX) should be factory setting for the used refrigerant unaltered.
6 mm or 1/4" in diameter and is to be connected down- At combi adsorber valves the label on the capillary tube
stream of the remote bulb. An overbow is recommended indicates how to adjust the adjusting spindle (with arrow for
in order to prevent the ingress of oil into the equaliser line. direction), depending on the refrigerant used. This correction
 The bulb should preferably be positioned on the upper half performance of the valve is correct. The refrigerant used must
of a horizontal suction line but never after a liquid trap. As be marked on the label.
a general rule, bulbs of expansion valves should be
insulated to prevent them being affected by the ambient This superheat adjustment is calibrated for lowest
temperature. superheating and optimum evaporator utilisation. However,
 When soldering the valve, the valve body must not get adjusting spindle as follows:
 Do not bend or squeeze the bulb when tightening the bulb Turning clockwise reduced refrigerant mass flow,
=
clamp! increase of superheat
 Constructive modifications at the valve are not allowed. Turning increased refrigerant mass
=
Information for original equipment manufacturers: One turn of adjusting spindle alters superheat setting by
The valve series TLE can be customised to the
requirements of your series device in an optimum way.
Contact us!

Series TBE
FIXED ORIFICE, FLARE CONNECTIONS
PRODUCT DATA
Features
 TBE: with internal pressure equalisation; for single
circuits.
 TBEX: with external pressure equalisation; for optimal
achieved
TBEX 0.5 - 4.5 two-way the capillary tube and valve head
behaviour
 Optional available with gas charge and MOP
 Adjustable superheat for two-way construction
 Fixed superheat setting for angle construction
TBEX 0.5 - 4.5 angle
 Flare connections
Application stainless steel diaphragm welded using protective gas
Thermostatic expansion valves series TBE are used in plants  Fixed orifice
with one or more refrigerant circuits, especially for series  Refrigerants: R134a, R401A
installations mobile air-conditioning and cooling units with R22, R407C, R407A, R422D
flare connection, e. g. bus AC, train AC, transport cooling. R404A, R507A, R402A, R407B
Materials Further refrigerants on request.
Body brass
Specification
Connections brass
optimal control behaviour)
Bulb diameter 12 mm

Series TBE

Refrigerant Evaporation PS PF Refrigerants and MOP on request.

temperature range (bar(a)) (bar(a)) With gas charged valves and MOP it is under all operating
R134a, R401A +15 °C to -30 °C 34 37.4 capillary tube and the thermal head!
R22, R407C, +15 °C to -45 °C 36 39.6 With the Honeywell TBE series the thermal head is heated
R407A, R422D advantageously by the liquid refrigerant. The warm thermal
head is on the safe side at any time.
R404A, R507A, ±0 °C to -50 °C 36 39.6
R402A, R407B
bulb.
Thus, Honeywell TBE(X) valves with combi adsorber charge
2. Adsorber charge with pressure limiting performance (MOP)

range
R134a, +5 °C to -30 °C MOP A +15 °C 34 37.4
R401A
-10 °C to -30 °C MOP A ±0 °C 29 31.9
R22, +5 °C to -45 °C MOP A +15 °C 36 39.6
R407C,
-10 °C to -45 °C MOP A ±0 °C 29 31.9
R407A,
R422D -27 °C to -45 °C MOP A -18 °C 29 31.9
R404A, -10 °C to -50 °C MOP A ±0 °C 36 39.6
R507A,
-20 °C to -50 °C MOP A -10 °C 34 37.4
R402A,
R407B -27 °C to -50 °C MOP A -18 °C 34 37.4
Capacities
Type Orifice size
R134a R22 R407C R422D R404A R507A
0.5 0.69 0.99 0.95 0.67 0.68 0.69
0.7 1.0 1.4 1.3 0.92 0.97 0.98
1.0 1.4 2.0 1.9 1.3 1.4 1.4
1.5 2.2 3.2 3.1 2.2 2.2 2.3
TBE
2.0 2.9 4.0 3.9 2.7 2.8 2.9
TBEX
2.5 4.0 5.8 5.6 3.9 4.1 4.1
3.0 6.6 9.3 8.9 6.3 6.5 6.6
3.5 8.7 12.2 11.7 8.3 8.6 8.7
4.5 11.8 17.0 16.4 11.3 12.0 12.1

Connections Dimensions (mm)
Weight
Type Inlet Outlet Pressure D E F G H I (kg)
(A) (B) equalisation (C)
Two-way
5/8" UNF 3/4" UNF 7/16" UNF 47.5 40 51.5 38 43 29 approx. 0.34
construction
Angle
3/4" UNF 7/8" UNF 7/16" UNF 42.5 - 46.5 40 - 29 approx. 0.34
construction
Connection = size of UNF thread
TBE(X) 0.5 - 4.5 two-way TBEX 0.5 - 4.5 angle

TBE X 4.5 R134a MOP A +15 °C 5/8“ x 3/4“ D
Series
X = external
() = internal
Orifice size
Refrigerant
Charge type, MOP,
Flare connection UNF
(inlet x outlet)

Series TBE
Installation Superheat Adjustment (Two-way Valve)

 The external pressure equaliser line (TBEX) should be factory setting for the used refrigerant unaltered.
6 mm or 1/4" in diameter and is to be connected down- This superheat adjustment is calibrated for lowest
stream of the remote bulb. An overbow is superheating and optimum evaporator utilisation. However,
recommended in order to prevent the ingress of oil into should it be necessary to adjust the superheat, turn the
the equaliser line. adjusting spindle as follows:
 The bulb should preferably be positioned on the upper Turning clockwise reduced refrigerant mass flow,
half of a horizontal suction line but never after a liquid =
be insulated to prevent them being affected by the Turning increased refrigerant mass
=
ambient temperature. counterclockwise flow, decrease of superheat
 When tightening flare nuts of the flare connections grip at One turn of adjusting spindle alters superheat setting by
wrench flats on the valve body. approx. 0.25 bar. Increase of superheat setting results in a
 Do not bend or squeeze the bulb when tightening the bulb lower MOP-value and vice versa.
clamp! With TBEX angle construction there is no superheat
 Constructive modifications at the valve are not allowed. setting in built-in condition possible, use factory setting.

The valve series TBE can be customised to the
Contact us!

Series TOE
FIXED ORIFICE, O-RING CONNECTIONS
PRODUCT DATA
Features
 TOE: with internal pressure equalisation; for single
circuits.
 TOEX: with external pressure equalisation; for optimal
achieved
TOEX 0.5 - 4.5 two-way  Charge is not sensitive to effects of temperature on

behaviour
 Optional available with gas charge and MOP
 Adjustable superheat for two-way construction
 Fixed superheat setting for angle construction
TOEX 0.5 - 4.5 angle
 O-ring connections
Application stainless steel diaphragm welded using protective gas
Thermostatic expansion valves series TOE(X) are used in  Fixed orifice
plants with one or more refrigerant circuits, especially for  Refrigerants: R134a
series installations, mobile air-conditioning and cooling units R22, R407C, R422D
with O-ring connection, e. g. bus AC, train AC, transport R404A, R507A
cooling. HFO (e.g. R1234yf) and future Blends
Materials
Body brass
Specification
Thermal head stainless steel Nominal capacity range 0.99 to 17.0 kW R22
Connections brass
optimal control behaviour)
Bulb diameter 12 mm

Series TOE

Refrigerant Evaporation PS PF Refrigerants and MOP on request.

temperature range (bar(a)) (bar(a)) With gas charged valves and MOP it is under all operating
R134a +15 °C to -30 °C 34 37.4 capillary tube and the thermal head!
R22, R407C, R422D +15 °C to -30 °C 36 39.6 With the Honeywell TOE series the thermal head is heated
R404A, R507A ±0 °C to -30 °C 36 39.6 advantageously by the liquid refrigerant. The warm thermal
bulb.
Thus, Honeywell TOE(X) valves with combi adsorber charge
2. Adsorber charge with pressure limiting performance (MOP)

range
R134a +5 °C to -30 °C MOP A +15 °C 34 37.4
-10 °C to -30 °C MOP A ±0 °C 29 31.9
R22, +5 °C to -30 °C MOP A +15 °C 36 39.6
R407C,
-10 °C to -30 °C MOP A ±0 °C 29 31.9
R422D
R404A, -10 °C to -30 °C MOP A ±0 °C 36 39.6
R507A
-20 °C to -30 °C MOP A -10 °C 34 37.4
Capacities
Type Orifice size
R134a R22 R407C R422D R404A R507A
0.5 0.69 0.99 0.95 0.67 0.68 0.69
0.7 1.0 1.4 1.3 0.92 0.97 0.98
1.0 1.4 2.0 1.9 1.3 1.4 1.4
1.5 2.2 3.2 3.1 2.2 2.2 2.3
TOE
2.0 2.9 4.0 3.9 2.7 2.8 2.9
TOEX
2.5 4.0 5.8 5.6 3.9 4.1 4.1
3.0 6.6 9.3 8.9 6.3 6.5 6.6
3.5 8.7 12.2 11.7 8.3 8.6 8.7
4.5 11.8 17.0 16.4 11.3 12.0 12.1

Connections Dimensions (mm)
Weight
Type Inlet Outlet Pressure D E F G H I (kg)
(A) (B) equalisation (C)
Two-way
5/8" UNF 3/4" UNF 7/16" UNF 47.5 40 51.5 38 43 29 approx. 0.34
construction
Angle
3/4" UNF 7/8" UNF 7/16" UNF 42.5 - 46.5 40 - 29 approx. 0.34
construction
Connection = size of UNF thread
TOE(X) 0.5 - 4.5 two-way TOEX 0.5 - 4.5 angle

TOE X 4.5 R134a MOP A +15 °C 5/8“ x 3/4“ D
Series
X = external
() = internal
Orifice size
Refrigerant
Charge type, MOP,
O-ring connection UNF
(inlet x outlet)

Series TOE
Installation Superheat Adjustment (Two-way Valve)

 The external pressure equaliser line (TOEX) should be factory setting for the used refrigerant unaltered.
6 mm or 1/4" in diameter and is to be connected down- This superheat adjustment is calibrated for lowest
stream of the remote bulb. An overbow is recommended superheating and optimum evaporator utilisation. However,
in order to prevent the ingress of oil into the equaliser line. should it be necessary to adjust the superheat, turn the
adjusting spindle as follows:
 The bulb should preferably be positioned on the upper
half of a horizontal suction line but never after a liquid Turning clockwise reduced refrigerant mass flow,
trap. As a general rule, bulbs of expansion valves should =
be insulated to prevent them being affected by the
ambient temperature. Turning increased refrigerant mass
=
wrench flats on the valve body. One turn of adjusting spindle alters superheat setting by
 Do not bend or squeeze the bulb when tightening the bulb approx. 0.25 bar. Increase of superheat setting results in a
clamp! lower MOP-value and vice versa.
 Constructive modifications at the valve are not allowed. With TOEX angle construction there is no superheat
setting in built-in condition possible, use factory setting.

The valve series TOE can be customised to the
Contact us!

Series TLESX
FIXED ORIFICE, ADJUSTABLE SUPERHEAT SETTING, SINGLE PORT
PRODUCT DATA
Features
 Damped gas charge with MOP as standard
 Optional available with liquid charge
 External pressure equalisation
 Single port construction, without high pressure
compensation
 Fixed orifice
 Refrigerants: R22, R134a, R404A, R407C, R410A
Specification
Evaporating temperature range see table on page 72
Application
Max. bulb temperature gas charge: 140 °C
Thermostatic expansion valves series TLESX are used in liquid charge: 70 °C
plants with one or more refrigerant circuits, in particular for
series installations such as bus and train air-conditioning Static superheat approx. 3 K
units, mobile air-conditioning and cooling units, chiller units Length of capillary tube 2m
and heat pumps. Bulb diameter 16 mm
Materials
Body brass

Series TLESX

1. Gas charge with pressure limiting MOP 2. Liquid charge
Refri- Evaporation MOP PS PF Refrigerants on request.

range
R22 +15 °C to -45 °C MOP +15 °C 36 39.6
R134a +15 °C to -40 °C MOP +15 °C 34 37.4
R404A +10 °C to -50 °C MOP +10 °C 36 39.6
R407C +10 °C to -30 °C MOP +10 °C 36 39.6
+15 °C to -30 °C MOP +15 °C 36 39.6
R410A +15 °C to -30 °C MOP +15 °C 40 44
MOP valves protect the compressor by limiting the increase of
suction pressure.
suction pressure of the compressor or min. 5 K higher than the
required evaporating temperature of the system.
With the Honeywell TLESX series the thermal head is heated
advantageously by the liquid refrigerant. The warm thermal
Capacities
Type Orifice size
R22 R134a R404A R407C R410A
4.75 22.4 15.9 15.8 21.6 26.8
TLESX 5 29.1 20.0 20.5 28.0 34.8
6 42.4 27.6 29.8 40.8 50.8

Connections Dimensions
(mm) Weight
Type Inlet Outlet Pressure equalizer F G (kg)
(E) (A) (DA)
54
1/2‘‘ ODF 5/8‘‘ ODF 1/4‘‘ ODF
TLESX 54 approx. 0.8
61
5/8‘‘ ODF 7/8‘‘ ODF 1/4‘‘ ODF

TLESX

TLESX 5 R134a MOP +15 °C 12 mm x 16 mm
Series
Orifice size
Refrigerant
MOP,
(inlet x outlet)

Series TLESX
Influence of Condensation Pressure to the Static Superheat Setting
3
Variation of static superheat setting [K]
-1
-2
T L E S X 4 ,7 5
-3
T LESX 5 + 6
-4
-5
7 9 11 13 15 17 19 21 23 25
c o n d e n s a tio n p re s s u re [b a r]

 The valves may be installed in any position. In general the valves should be installed with the factory
 The external pressure equaliser line should be 6 mm or setting for the used refrigerant unaltered. This setting is
1/4" in diameter and is to be connected downstream of calibrated for lowest superheating and optimum evaporator
the remote bulb. An overbow is recommended in order to utilization. However, should it be necessary to adjust the
prevent the ingress of oil into the equaliser line. superheat, turn the adjusting spindle as follows:
=
 When soldering the valve, the valve body must not get One turn of the adjusting spindle alters superheat setting by
warmer than 100 °C. approx. 0.3 bar. Increase of superheat setting results in a
 Do not bend or squeeze the bulb when thightening the lower MOP value and vice versa.
bulb clamp!

The valve series TLESX can be customised to the
Contact us!

Series TLEX
FIXED ORIFICE, ADJUSTABLE SUPERHEAT SETTING, BALANCED PORT
PRODUCT DATA
Features
 Fixed orifice
Specification
(simultaneous on all
Application connections)
Thermostatic expansion valves series TLEX are used in Max. ambient temperature 100 °C
series installations such as chiller units, heat pumps, and Max. bulb temperature gas charge: 140 °C
transport cooling. liquid charge: 70 °C
Materials Length of capillary tube 2m
Body brass Bulb diameter 16 mm

Series TLEX

1. Gas charges with pressure limiting MOP 2. Liquid charge

range
R22 +15 °C to -45 °C MOP +15 °C 36 39.6
+10 °C to -45 °C MOP +10 °C 36 39.6
R134a +20 °C to -40 °C MOP +20 °C 34 37.4
+15 °C to -40 °C MOP +15 °C 34 37.4
+10 °C to -40 °C MOP +10 °C 34 37.4
R404A +10 °C to -45 °C MOP +10 °C 36 39.6
±0 °C to -45 °C MOP ±0 °C 36 39.6
R407C +15 °C to -30 °C MOP +15 °C 36 39.6
+15 °C to -45 °C MOP +15 °C 36 39.6
R410A +15 °C to -30 °C MOP +15 °C 40 44
suction pressure.
Capacities
Type Orifice size
R22 R134a R404A R407C R410A
4.75 22.4 15.9 15.8 21.6 26.8
5 29.1 20.0 20.5 28.0 34.8
TLEX
6 42.4 27.6 29.8 40.8 50.8
7 54.5 35.3 38.3 52.5 65.3

Type Orifice Connections Dimensions (mm)
Weight
size Inlet Outlet Pressure equalizer F G
(kg)
(E) (A) (DA)
4.75 12 mm ODF 16 mm ODF 6 mm ODF 54±2
5 1/2" ODF 5/8" ODF 1/4" ODF 54±2
TLEX 54±2 Approx. 0.86
6 16 mm ODF 22 mm ODF 6 mm ODF 61±2
7 5/8" ODF 7/8" ODF 1/4" ODF 61±2

TLEX 4.75 - 7

TLEX 6 R22 MOP +15 °C 16 mm x 22 mm
Series
Orifice size
Refrigerant
MOP,
(inlet x outlet)

Series TLEX

1/4" in diameter and is to be connected downstream of the calibrated for lowest superheating and optimum evaporator
remote bulb. An overbow is recommended in order to utilization. However, should it be necessary to adjust the
=
 When soldering the valve, the valve body must not get One turn of the adjusting spindle alters superheat setting by
bulb clamp!

The valve series TLEX can be customised to the
Contact us!

Series TLEX 8 - 11
FIXED ORIFICE, ADJUSTABLE SUPERHEAT SETTING, BALANCED PORT
PRODUCT DATA
Features
 Fixed orifice
Specification
(simultaneous on all
Application connections)
Thermostatic expansion valves series TLEX are used in Max. ambient temperature 100 °C
series installations such as air conditioning units, chiller units Max. bulb temperature gas charge: 140 °C
and heat pumps. liquid charge: 70 °C
Materials Length of capillary tube 2m
Body brass Bulb diameter 16 mm

Series TLEX 8 - 11

1. Gas charge with pressure limiting MOP 2. Liquid charge

range
R22 +15 °C to -45 °C MOP +15 °C 36 39.6
R134a +15 °C to -40 °C MOP +15 °C 34 37.4
R404A +10 °C to -50 °C MOP +10 °C 36 39.6
R407C +15 °C to -30 °C MOP +15 °C 36 39.6
R410A +15 °C to -30 °C MOP +15 °C 40 44
suction pressure.
With the Honeywell TLEX series the thermal head is heated
advantageously by the liquid refrigerant. The warm thermal
Capacities
Type Orifice size
R22 R134a R404A R407C R410A
8 64.1 43.3 45.1 61.8 76.9
TLEX 10 75.1 51.0 52.8 72.3 90.0
11 95.8 65.0 67.4 92.3 115

Type Orifice Anschlüsse Weight
size Inlet Outlet Pressure equalizer (kg)
(E) (A) (DA)
8
TLEX 10 approx. 1.3
7/8" ODF 1 1/8" ODF 1/4" ODF
11
7/8" ODF 1 3/8" ODF 1/4" ODF

TLEX 8 - 11

TLEX 8 R134a MOP +15 °C 22 mm x 28 mm
Series
Orifice size
Refrigerant
MOP, evaporation temperature range
(inlet x outlet)

Series TLEX 8 - 11

1/4" in diameter and is to be connected downstream of the calibrated for lowest superheating and optimum evaporator
remote bulb. An overbow is recommended in order to utilization. However, should it be necessary to adjust the
=
 When soldering the valve, the valve body must not get One turn of adjusting spindle alters superheat setting by
bulb clamp!

The valve series TLEX can be customised to the
Contact us!

Series CVC and HLE
HOT GAS BYPASS VALVES
FIXED ORIFICE, ADJUSTABLE SUCTION PRESSURE LIMITATION
PRODUCT DATA
Features
 CVC: Orifice size 4.0,
equivalent to 1 kW bypass capacity R134a
 HLE: Orifice size 4.5S,
equivalent to 1.5 kW bypass capacity R134a
 Adjustable suction pressure limitation
 Fixed orifice
CVC HFO (e.g. R1234yf) and future Blends
not for ammonia
HLE
Specification
Adjusting range for 1 - 6 bar(a) (CVC)
suction pressure limitation 1 - 9 bar(a) (HLE)
Application Factory setting 3.2 bar(a) (CVC)
Hot gas bypass valves series CVC and HLE are used to 3.5 bar(a) (HLE)
adjust the compressor capacity to the actual evaporator Maximum pressure PS 25.5 bar(a)
capacity in a refrigerating plant.
Maximum test pressure PF 28 bar(a)
The hot gas bypass valve can be installed in a bypass tube
between the hot gas line and suction line. The suction Max. ambient temperature 100 °C
pressure is downward limited by flowing hot gas from the high
pressure to the low pressure side. Installation
For plants in general refrigeration and for original equipment
such as dehumidifiers, air driers, water coolers or ice-making  The valves may be installed in any position.
machines.  When soldering the valve, the valve body must not get
Materials  Remove plastic cap during soldering
Body brass  Constructive modifications at the valve are not allowed.
Head stainless steel, brass
Adjustment
One complete revolution of the adjusting screw effects an
alternation of the suction pressure limitation by approx.
0.5 bar (CVC) resp. 0.4 bar (HLE).
Turning clockwise = Higher suction pressure

Turning
= Lower suction pressure
counterclockwise

Series CVC and HLE
Capacities
Condensing pOffset Bypass-capacity QN
Valve temperature tc (bar) (kW)
Type
size (°C) R134a R407C R404A
0.5 0.62 1.05 0.88
35
0.7 0.85 1.45 1.20
CVC 4.0
0.5 0.71 1.16 0.88
50
0.7 1.00 1.60 1.20
0.5 0.98 1.67 1.40
35
0.7 1.37 2.33 1.95
HLE 4.5S
0.5 1.13 1.86 1.41
50
0.7 1.57 2.60 1.97
Evaporating temperature to: 0 °C; Hot gas superheat tV2oh: 25 K

Type Valve Connections Dimensions (mm) Weight
size (kg)
Inlet (A) Outlet (B) C D E F
6 mm ODF 12 mm ODF
CVC 4.0 64 43 113 61 approx. 0.16
1/4" ODF 1/2" ODF
10 mm ODF 12 mm ODF
HLE 4.5S 71 46 142 65 approx. 0.3
3/8" ODF 1/2" ODF
CVC HLE

Series HLEX 4.75 - 7 and HLEX 8 - 11
HOT GAS BYPASS VALVES
FIXED ORIFICE, ADJUSTABLE SUCTION PRESSURE LIMITATION
PRODUCT DATA
Features
 Compact design
 Adjustable suction pressure limitation
 Fixed orifice
not for ammonia
HLEX 4,75 - 7 Specification

Adjusting range for
suction pressure limitation 1 - 9 bar(a)
HLEX 8 - 11
Factory setting 3.7 bar(a)
Maximum pressure PS 29 bar(a)
Application Maximum test pressure PF 32 bar(a) (simultanous on
all connections)
Hot gas bypass valves series HLEX are used to adjust the
compressor capacity to the actual evaporator capacity in a Max. ambient temperature 100 °C
refrigerating plant.
The hot gas bypass valve can be installed in a bypass tube Installation
between the hot gas line and suction line. The suction  The valves may be installed in any position.
pressure is downward limited by flowing hot gas from the high
pressure to the low pressure side.  When soldering the valve, the valve body must not get
For plants in general refrigeration and for original equipment warmer than 100 °C.
such as dehumidifiers, air driers, water coolers or ice-making  Remove plastic cap during soldering
machines.  Constructive modifications at the valve are not allowed.
Materials Adjustment
Body brass One complete revolution of the adjusting screw effects an
Head stainless steel, brass alternation of the suction pressure limitation by approx.
0.5 bar.
Turning clockwise = Higher suction pressure
Turning
= Lower suction pressure
counterclockwise

Capacities
Condensing pOffset Bypass-capacity QN (kW)
Type Orifice size temperature tc
R134a R407C R404A
(°C) (bar)
0.5 0.98 1.67 1.40
35
0.7 1.37 2.33 1.95
4.75
0.5 1.13 1.86 1.41
50
0.7 1.57 2.60 1.97
0.5 1.29 2.18 1.83
35
0.7 1.79 3.04 2.55
5
0.5 1.47 2.43 1.84
50
0.7 2.05 3.39 2.57
0.5 1.92 3.26 2.73
35
0.7 2.68 4.54 3.81
6
0.5 2.20 3.64 2.75
50
0.7 3.07 5.07 3.83
0.5 2.35 3.98 3.34
35
0.7 3.27 5.55 4.65
HLEX 7
0.5 2.69 4.44 3.36
50
0.7 3.75 6.19 4.68
0.5 2.66 4.52 3.79
35
0.7 3.72 6.31 5.29
8
0.5 3.05 5.04 3.81
50
0.7 4.26 7.04 5.32
0.5 3.29 5.57 4.67
35
0.7 4.58 7.77 6.52
10
0.5 3.76 6.22 4.70
50
0.7 5.25 8.67 6.56
0.5 4.50 7.63 6.40
35
0.7 6.29 10.66 8.94
11
0.5 5.16 8.52 6.45
50
0.7 7.20 11.90 9.00
Evaporating temperature to: 0 °C; hot gas superheat tV2oh: 25 K

HLEX 5 12 mm x 16 mm
Series
Orifice size
Solder connections ODF
(inlet x outlet)

Connections
Weight
Type Orifice size Inlet Outle Pressure equalizer (kg)
(E) (A) (DA)
4,75
5
approx. 0.9
6
1/2‘‘ ODF 5/8‘‘ ODF 1/4‘‘ ODF
HLEX 7
8 16 mm ODF 22 mm ODF 6 mm ODF
10 approx. 1.3
11 5/8‘‘ ODF 7/8‘‘ ODF 1/4‘‘ ODF
HLEX 4.75 - 7 HLEX 8 - 11

Application Samples
Hot gas bypass in the suction line
Hot gas bypass in the evaporator inlet

Series NMVL and NMX
LIQUID INJECTION VALVES
SUCTION PRESSURE CONTROLLED, INTERCHANGEABLE ORIFICE CARTRIDGES
PRODUCT DATA
Features
 Suction gas controlled liquid injection valves
 Part programme containing:
Valve body head, orifice cartridge, connection base
 Honeywell NMVL:
- Only one valve body head needed both for internal
and external pressure equalisation
- Connection for pressure coupler integrated
in the solder base
- solder base two-way or angle construction
 Honeywell NMX:
- Balanced port
- External pressure equalisation integrated in the
valve body head
- solder base two-way or angle construction
- flare base two way construction
NMVL
 Interchangeable orifice cartridges
 Liquid charge
 Refrigerants: R134a, R22, R404A, R407C, R507A
NMX HFO (e.g. R1234yf) and future Blends
 Further refrigerants on request.
Application Specification
Honeywell thermostatic liquid injection valves series NMVL
and NMX are used in refrigeration applications to reduce the (small orifice graduation for
temperature of the suction gas. optimal control behaviour)
Depending on the superheat of the compressor suction gas, Temperature range -50 °C to +65 °C
liquid refrigerant is injected into the suction line. The Maximum pressure PS See table on page 90
refrigerant is evaporating and thereby the suction gas is
Maximum test pressure PF See table on page 90
cooled down.
Suitable for plants in general refrigeration and for serial Max. ambient temperature 70 °C
products such as air driers, dehumidifiers, chiller units or Max. bulb temperature 70 °C
ice-making machines with hot gas bypass control valves, for Static superheat See table on page 90
temperature reduction in multiple stage units and for suction Length of capillary tube NMVL: 1.5 m
gas cooled compressors.
NMX: 3.0 m
Bulb diameter NMVL: 12 mm
NMX: 16 mm
Materials
Body, base brass
Connections copper or brass

Series NMVL and NMX
Thermal Charges and Static Superheat

Code for Superheat PS PF
thermal charge R134a R22 R404A R407C R507A (bar(a)) (bar(a))
DA - 15 K 21 K 12 K 21 K 34 37.4
TA 15 K 30 K 35 K 26 K 35 K 29 31.9
LB 30 K 45 K - 40 K - 29 31.9
The superheat is based on to = +0 °C.
Capacities
Type Orifice size Nominal capacity (kW)*
R134a R22 R404A R407C R507A
0.3 0.36 0.52 0.36 0.50 0.36
0.5 0.69 0.99 0.68 0.95 0.69
0.7 0.96 1.4 0.97 1.3 0.98
1.0 1.4 2.0 1.4 1.9 1.4
1.5 2.2 3.2 2.2 3.1 2.3
NMVL 2.0 2.9 4.0 2.8 3.9 2.9
2.5 4.0 5.8 4.1 5.6 4.1
3.0 6.6 9.3 6.5 8.9 6.6
3.5 8.7 12.2 8.6 11.7 8.7
4.5 11.8 17.0 12.0 16.4 12.1
4.75 15.9 22.4 15.8 21.6 15.9
4.5 11.8 17.0 12.0 16.4 12.1
4.75 15.9 22.4 15.8 21.6 15.9
5 20.0 29.1 20.5 28.0 20.7
NMX 6 27.6 42.4 29.8 40.8 30.1
7 35.3 54.5 38.3 52.5 38.7
8 43.3 64.1 45.1 61.8 45.6
10 51.0 75.1 52.8 72.3 53.3
* Capacities are based on to = +4 °C. tc = +38 °C and 1 K subcooled liquid refrigerant entering the valve.

(kg)
Inlet Outlet Pressure equalizer
(A) (B) (C)
NMVL - - - approx. 0.43
VD - - - approx. 0.02
1/4" ODF 3/8" ODF -
VLS 10 mm ODF 12 mm ODF -
approx. 0.16
angle 3/8" ODF 1/2" ODF -
1/2" ODF 5/8" ODF -
1/4" ODF 3/8" ODF 1/4" ODF
VLSX 10 mm ODF 12 mm ODF 6 mm ODF
approx. 0.17
angle 3/8" ODF 1/2" ODF 1/4" ODF
1/2" ODF 5/8" ODF 1/4" ODF
VLS 3/8" ODF 1/2" ODF -
approx. 0.16
two-way 12 mm ODF 16 mm ODF -
1/2" ODF 5/8" ODF -
VLSX 3/8" ODF 1/2" ODF 1/4" ODF
approx. 0.17
two-way 12 mm ODF 16 mm ODF 6 mm ODF
1/2" ODF 5/8" ODF 1/4" ODF
NMVL
VD VLS(X) – two-way VLS(X) - angle

Series NMVL and NMX

(kg)
Inlet Outlet Pressure equalizer
(A) + (B) (C) + (D)
NMX - - 7/16" UNF approx. 0.6
XD - - - approx. 0.14
XLS 12 + 16 mm ODF 16 + 22 mm ODF -
approx. 0.41
two-way 1/2" + 5/8" ODF 5/8" + 7/8" ODF -
XLS 12 + 15 mm ODF 16 + 22 mm ODF -
approx. 0.32
angle 1/2" + 5/8" ODF 5/8" + 7/8" ODF -
XBS
7/8" UNF 7/8" UNF - approx. 0.49
two-way
NMX
XD XBS – two-way
XLS - angle XLS - two-way

(Part Programme)
1. Valve body head 2. Orifice cartridge
NMVL DA VD 0.5
Series (NMVL, NMX) Series (VD, XD)
Code for thermal charge Orifice size
3. Connection base
VLS X 10 mm ODF x 12 mm ODF W

Series (VLS, XLS, XBS)
Pressure equalizer VLS:
X = external
() = internal
Connection size
(Inlet x Outlet)

 The valves may be installed in any position. In general the Honeywell liquid injection valves should be
 The external pressure equaliser line (VLSX and NMX) installed with the factory setting for the used refrigerant
should be 6 mm or 1/4" in diameter. It is connected to the unaltered.
suction line downstream of the remote bulb. An overbow is This superheat adjustment is calibrated for the above
recommended in order to prevent the ingress of oil into the mentioned superheat and optimal control behaviour.
equaliser line. However, should it be necessary to adjust the superheat,
turn the adjusting spindle as follows:
 The bulb should preferably be positioned on the upper half
of a horizontal suction line but never after a liquid trap. As Turning clockwise reduced refrigerant mass flow,
a general rule, bulbs of liquid injection valves should be =
insulated to prevent them being affected by the ambient
temperature. Turning increased refrigerant mass
=
 Do not bend or squeeze the bulb when tightening the bulb
clamp. One turn of the adjusting spindle alters superheat setting by
 Never quench the solder base with water after soldering, approx. 0.55 bar for NMVL and 0.3 bar for NMX.
this may cause cracks and distort the sealing surfaces.
wrench flats on the valve body.
 The screws fixing the valve body head to the base must be
tightened in diagonal sequence. Torque 12+1 Nm for NMVL
and 16+1 Nm for NMX.

Series NMVL and NMX
Application Sample
4 1 2 5
Power control with hot gas bypass valve and temperature reduction
of suction gas with liquid injection valve
1 Liquid Injection Valve

2 Hot gas bypass Valve
3 Thermostatic Expansion Valve
4 Liquid - Solenoid Valve
5 Hot gas - Solenoid Valve

Series M
SOLENOID VALVES
NORMALLY CLOSED
PRODUCT DATA
Features
 MA: direct operated, angle construction
 MD: direct operated, two way construction
 MS: pilot operated, two way construction
 Normally closed
MA  High performance
MD  Direct operated: no minimum pressure differential
required to open the valve
 Pilot operated: minimum pressure differential of
0.05 bar required to open the valve
 Solder and flare connections
 Coils for AC and DC
not for ammonia
Specification
MS
Nominal capacity see tables on page 96
Application Maximum test pressure PF 50 bar(a)
Min. pressure differential MA, MD: 0 bar
Solenoid valves series M are used in general refrigeration
and for original equipment to cut off/activate the refrigerant MS: 0.05 bar
flow in a refrigerating plant. Max. pressure differential MS: 2 bar
The solenoid valves can be installed in the liquid line, hot gas Max. opening pressure AC-coil: MA, MD: 25 bar
line and suction line of a refrigerating unit. differential MOPD MS: 30 bar
DC-coil: MA, MD: 21bar
Materials MS: 21 bar
Body brass, stainless steel Max. medium temperature 125 °C
Seal material PTFE Min. medium temperature -45 °C
Connection tubes solder: copper Max. ambient temperature 80 °C
flare: brass Min. ambient temperature -40 °C
Coil copper, steel, Crastin Number of operating cycles > 1,5 million
Standard coil voltages AC: 230V, 110V, 24V
DC: 230V, 24V
further voltages on request
Voltage tolerance AC: ±10%
DC: +10%, -5%

Series M
Nominal Capacity QN (kW)

Liquid Hot gas Suction gas
kv-value
Typ R134a R22 R407C R404A R134a R22 R407C R404A R134a R22 R407C R404A
(m3/h)
R507A R507A R507A
Direct operated
MA 062 0.17 5.21 5.62 5.39 3.87 1.14 1.47 1.45 1.29 - - - -
MD 062 0.17 5.21 5.62 5.39 3.87 1.14 1.47 1.45 1.29 - - - -
MD 103 0.23 7.05 7.61 7.29 5.24 1.54 1.99 1.96 1.75 - - - -
Pilot operated
MS 103 0.9 27.6 29.8 28.5 20.5 6.04 7.78 7.67 6.83 1.54 2.06 1.92 1.80
MS 104 0.9 27.6 29.8 28.5 20.5 6.04 7.78 7.67 6.83 1.54 2.06 1.92 1.80
MS 124 1.6 49.0 52.9 50.7 36.4 10.7 13.8 13.6 12.1 2.74 3.66 3.42 3.19
MS 125 1.6 49.0 52.9 50.7 36.4 10.7 13.8 13.6 12.1 2.74 3.66 3.42 3.19
MS 165 2 61.3 66.1 63.4 45.5 13.4 17.3 17.1 15.2 3.42 4.57 4.27 3.99
MS 167 2 61.3 66.1 63.4 45.5 13.4 17.3 17.1 15.2 3.42 4.57 4.27 3.99
MS 227 4 123 132 127 91.1 26.8 34.6 34.1 30.4 6.85 9.14 8.54 7.98
The nominal capacity QN is based on the following conditions
Medium Evaporating Condensing Subcooling Hot gas Pressure loss

temperature temperature temperature across valve
to (°C) tc (°C) tc2u (K) tH (°C) p (bar)
Liquid -10 25 1 - 0.4
Hot gas -10 25 1 50 °C 1
Suction gas -10 25 1 - 0.15
Valve selection for other operating conditions see the following tables or consult the Honeywell software

Valve size calculation for the liquid line
Refrigeration capacity Q0, multiplied with correcting factor fTF,
multiplied with correcting factor fPF results in the required
nominal capacity QN.
QN = Qo x fTF x fPF
QN nominal capacity (according to table on page 96)
Qo refrigeration capacity
fTF correcting factor for evaporating and liquid
temperature
fPF correcting factor for pressure loss across the valve
Correcting factor fTF for the change of capacity according to the operating temperatures
Evaporating temperature to (°C)

tL*
R134a R22 R407C R404A, R507A
(°C)
+10 ±0 -10 -20 -30 -40 +10 ±0 -10 -20 -30 -40 +10 ±0 -10 -20 -30 +10 ±0 -10 -20 -30 -40
0 - - 0.80 0.83 0.85 0.88 - - 0.82 0.83 0.85 0.88 - - 0.80 0.80 0.80 - - 0.73 0.76 0.79 0.83
+5 - - 0.83 0.86 0.89 0.93 - - 0.85 0.87 0.89 0.91 - 0.80 0.80 0.80 0.90 - - 0.77 0.8 0.84 0.88
+10 - 0.84 0.87 0.91 0.94 0.97 - 0.86 0.88 0.90 0.92 0.95 - 0.80 0.90 0.90 0.90 - 0.79 0.82 0.85 0.89 0.94
+15 - 0.88 0.91 0.94 0.98 1.02 - 0.90 0.92 0.94 0.96 0.99 0.90 0.90 0.90 0.90 1.00 - 0.84 0.87 0.91 0.95 1.00
+20 0.89 0.92 0.95 0.99 1.03 1.08 0.92 0.94 0.96 0.98 1.00 1.03 0.90 0.90 0.90 1.00 1.00 0.86 0.89 0.93 0.97 1.02 1.08
+25 0.94 0.96 1.00 1.05 1.09 1.14 0.96 0.98 1.00 1.03 1.05 1.09 0.90 1.00 1.00 1.00 1.10 0.92 0.96 1.05 1.05 1.11 1.18
+30 0.99 1.02 1.06 1.12 1.16 1.22 1.01 1.02 1.05 1.08 1.10 1.14 1.00 1.00 1.00 1.10 1.20 0.99 1.03 1.08 1.14 1.21 1.29
+35 1.04 1.08 1.12 1.18 1.24 1.30 1.05 1.07 1.10 1.13 1.16 1.20 1.10 1.10 1.10 1.20 1.20 1.08 1.13 1.19 1.26 1.34 1.44
+40 1.10 1.14 1.19 1.26 1.32 1.39 1.10 1.12 1.15 1.19 1.22 1.26 1.10 1.20 1.20 1.30 1.30 1.18 1.24 1.32 1.40 1.50 1.63
+45 1.18 1.22 1.28 1.35 1.42 1.50 1.17 1.19 1.22 1.26 1.29 1.34 1.20 1.30 1.30 1.40 1.40 1.32 1.39 1.48 1.59 1.72 1.88
+50 1.25 1.24 1.37 1.45 1.53 1.62 1.23 1.26 1.29 1.33 1.37 1.42 1.30 1.40 1.40 1.50 1.60 1.50 1.59 1.7 1.85 2.02 2.23
+55 1.35 1.41 1.48 1.58 1.67 1.78 1.30 1.33 1.37 1.42 1.46 1.52 1.40 1.50 1.60 1.70 1.80 1.74 1.87 2.02 2.22 2.47 2.79
+60 1.46 1.55 1.61 1.73 1.84 1.97 1.38 1.41 1.46 1.51 1.56 1.63 - - - - - - - - - - -
* Temperature of liquid refrigerant at valve inlet.
Correcting factor fPF for the change of capacity according to the chosen pressure loss across the valve
Pressure loss across valve p (bar) 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70
Correcting factor fPF 2.83 2.00 1.63 1.41 1.26 1.15 1.07 1.00 0.94 0.89 0.85 0.82 0.78 0.76

Series M
Valve capacity for the hot gas line

Type Pressure Capacity (kW)*
loss
Condensing temperature tc (°C)
across
valve R134a R22 R407C R404A, R507A
p (bar) +25 +30 +40 +50 +60 +25 +30 +40 +50 +60 +25 +30 +40 +50 +25 +30 +40 +50
Direct operated
0.2 0.54 0.55 0.57 0.58 0.57
0.68 0.70 0.74 0.76 0.78 0.62 0.65 0.68 0.70 0.60 0.60 0.58 0.53
MA 062 0.5 0.83 0.86 0.89 0.90 0.89
1.06 1.10 1.15 1.19 1.22 0.98 1.02 1.08 1.11 0.93 0.93 0.90 0.83
1.0 1.12 1.17 1.23 1.25 1.24
1.46 1.51 1.60 1.67 1.70 1.39 1.44 1.52 1.57 1.29 1.29 1.26 1.16
MD 062
1.5 1.31 1.38 1.47 1.50 1.50
1.74 1.81 1.93 2.01 2.06 1.71 1.77 1.87 1.93 1.54 1.55 1.52 1.41
2.0 1.44 1.52 1.64 1.70 1.70
1.94 2.04 2.19 2.29 2.34 1.96 2.04 2.15 2.22 - - - -
0.2 0.72 0.75 0.78 0.78 0.77
0.80 0.95 1.00 1.03 1.05 0.84 0.87 0.92 0.95 0.80 0.80 0.78 0.71
0.5 1.12 1.16 1.21 1.22 1.21
1.43 1.48 1.56 1.62 1.65 1.33 1.38 1.46 1.50 1.26 1.26 1.22 1.12
MD 103 1.0 1.51 1.58 1.67 1.69 1.68
1.98 2.05 2.17 2.25 2.30 1.88 1.95 2.06 2.13 1.74 1.74 1.70 1.57
1.5 1.77 1.86 1.98 2.03 2.02
2.35 2.45 2.61 2.72 2.78 2.31 2.39 2.52 2.61 2.08 2.09 2.05 1.90
2.0 1.94 2.06 2.22 2.30 2.30
2.64 2.76 2.96 3.10 3.17 2.66 2.76 2.91 3.01 - - - -
Pilot operated
0.2 2.83 2.93 3.04 3.06 3.02 4.20 4.33 4.55 4.70 4.79 3.60 3.71 3.90 4.03 3.09 3.09 3.00 2.74
MS 103 0.5 4.37 4.53 4.73 4.78 4.72 6.55 6.76 7.13 7.38 7.52 5.61 5.79 6.11 6.33 4.89 4.89 4.80 4.37
1.0 5.93 6.19 6.52 6.63 6.57 9.02 9.35 9.91 10.3 10.5 7.73 8.01 8.49 8.83 6.77 6.86 6.69 6.09
MS 104
1.5 6.93 7.29 7.77 7.95 7.92 10.8 11.2 11.9 12.4 12.7 9.26 9.60 10.2 10.6 8.14 8.14 8.06 7.37
2.0 7.60 8.07 8.66 9.00 9.00 12.1 12.6 13.5 14.2 14.5 10.4 10.8 11.6 12.2 - - - -
0.2 5.04 5.21 5.40 5.44 5.36 6.40 6.60 6.94 7.17 7.30 5.86 6.07 6.41 6.62 5.60 5.60 5.44 4.96
MS 124 0.5 7.77 8.07 8.40 8.50 8.39 9.97 10.3 10.9 11.2 11.5 9.27 9.6 10.1 10.5 8.76 8.76 8.52 7.80
1.0 10.5 11.0 11.6 11.8 11.7 13.7 14.3 15.1 15.7 16.0 13.1 13.6 14.3 14.8 12.1 12.1 11.8 10.9
MS 125
1.5 12.3 13.0 13.8 14.1 14.1 16.4 17.1 18.2 19.0 19.4 16.1 16.6 17.6 18.1 14.5 14.6 14.3 13.2
2.0 13.5 14.3 15.5 16.0 16.0 18.4 19.2 20.6 21.6 22.1 18.5 19.2 20.3 20.9 - - - -
0.2 6.29 6.51 6.76 6.80 6.70 8.00 8.25 8.68 8.96 9.12 7.33 7.59 8.01 8.28 7.00 7.00 6.80 6.20
MS 165 0.5 9.72 10.1 10.5 10.6 10.5 12.5 12.9 13.6 14.1 14.3 11.6 12.0 12.7 13.1 10.9 10.9 10.6 9.70
1.0 13.2 13.7 14.5 14.7 14.6 17.2 17.8 18.9 19.6 20.0 16.4 17.0 17.9 18.5 15.1 15.2 14.8 13.6
MS 167
1.5 15.4 16.2 17.2 17.7 17.6 20.5 21.3 22.7 23.7 24.2 20.1 20.8 22.0 22.7 18.1 18.2 17.9 16.5
2.0 16.9 17.9 19.3 20.0 20.0 23.0 24.0 25.7 27.0 27.6 23.2 24.0 25.3 26.2 - - - -
0.2 12.6 13.0 13.5 13.6 13.4 16.0 16.5 17.4 17.9 18.2 14.7 15.2 16.0 16.6 14.0 14.0 13.6 12.4
0.5 19.4 20.1 21.0 21.2 21.0 24.9 25.8 27.1 28.1 28.6 23.2 24.0 25.3 26.2 21.9 21.9 21.3 19.5
MS 227 1.0 26.3 27.5 29.0 29.5 29.2 34.4 35.6 37.8 39.2 40.0 32.8 33.9 35.8 37.0 30.3 30.4 29.7 27.3
1.5 30.8 32.4 34.5 35.3 35.2 41.0 42.6 45.4 47.4 48.4 40.1 41.6 43.9 45.3 36.3 36.5 35.8 33.1
2.0 33.8 35.9 38.7 39.9 40.0 45.9 48.0 51.5 53.9 55.2 46.3 48.0 50.7 52.4 - - - -
* Capacities are based on evaporating temperature to = -10 °C, hot gas temperature tH = +25 °C and 1 K subcooled refrigerant.
If the hot gas temperature is changed by ±10 °C the valve capacity changes (inversely proportional) by ±2,5 %.
With other evaporating temperatures to the capacities above should be multiplied by the following correcting factors:
to (°C) -50 -40 -30 -20 -10 ±0 +10

R134a - 0.85 0.90 0.95 1.00 1.05 1.09
R22 0.88 0.91 0.95 0.97 1.00 1.03 1.05
R407C 0.83 0.88 0.92 0.95 1.00 1.01 1.06
R404A, R507 0.75 0.81 0.88 0.13 1.00 1.05 -

Valve size calculation for the suction line
Refrigeration capacity Qo, multiplied with correcting factor fTS,
multiplied with correcting factor fPS results in the required
nominal capacity QN.
QN = Qo x fTS x fPS
QN nominal capacity (according to table on page 96)
Qo refrigeration capacity
fTS correcting factor for evaporating and liquid
temperature
fPS correcting factor for pressure loss across the valve
Correcting factor fTS for the change of capacity according to the operating temperatures
Evaporating Condensating temperature tc (°C)

temperature +60 +50 +40 +30 +20
to (°C)
For refrigerant R134a, R22, R407C
+10 0.98 0.86 0.78 0.71 0.66
±0 1.19 1.05 0.95 0.86 0.79
-10 1.48 1.29 1.16 1.05 0.96
-20 1.88 1.62 1.44 1.31 1.19
-30 2.42 2.08 1.83 1.65 1.59
-40 3.20 2.71 2.37 2.13 1.92
For refrigerant R404A, R507A
+10 - 1.14 0.82 0.71 0.63
±0 - 1.24 1.01 0.87 0.77
-10 - 1.57 1.26 1.07 0.94
-20 - 2.02 1.60 1.35 1.17
-30 - 2.67 2.07 1.72 1.49
-40 - 3.62 2.74 2.25 1.93
Correcting factor fPS for the change of capacity according to the chosen pressure loss across the valve
Pressure loss across valve p (bar) 0.05 0.075 0.10 0.15 0.20 0.30 0.40 0.50 0.60
Correcting factor fPS 1.73 1.41 1.22 1.00 0.87 0.71 0.61 0.55 0.50

Series M

1. Solenoid Valve
M S 16 5 S 230 V AC
Series
Type:
A = direct operated, angle
D = direct operated
S = pilot operated
Valve size
Connection size in 1/8”
() = flare connection
MMS = solder, metric
S = solder, inch
Voltage
() = without coil
2. Solenoid Coil
Type of coil, capacity For Solenoid Valve Voltage, frequency Voltage tolerance
MC 062, 8 W MA 062(S)(MMS) 230 V, 50/60 Hz
MD 062(S)(MMS) 110 V, 50/60 Hz ±10 %
24 V, 50/60 Hz
MC 102-227, 13 W MD 103(S)(MMS) 230 V, 50/60 Hz
MS 103-227(S)(MMS) 110 V, 50/60 Hz ±10 %
24 V, 50/60 Hz
MC 102-227, 20 W MD 103(S)(MMS)
24 V DC +10 %
MS 103-227(S)(MMS)
230 V DC -5 %
International protection rating IP65, coil incl. e.l.c.b.-protected plug to DIN 43650 with cable gland; conduit thread PG11.

Type Connections For tube Dimensions (mm) Weight (kg)
(E) diameter
A B C D without coil with coil
230 V AC 230 V AC
Direct operated
MA 062MMS 6 mm ODF 6 mm 88 88 142 47 0.15 0.30
MA 062S 1/4" ODF 1/4" 88 88 142 47 0.15 0.30
MD 062 7/16" UNF 6 mm, 1/4" 65 17 57 47 0.19 0.33
MD 062MMS 6 mm ODF 6 mm 112 17 57 47 0.17 0.31
MD 062S 1/4" ODF 1/4" 112 17 57 47 0.17 0.31
MD 103 5/8" UNF 10 mm, 3/8" 71 19 64 54 0.28 0.52
MD 103MMS 10 mm ODF 10 mm 118 19 64 54 0.25 0.49
MD 103S 3/8" ODF 3/8" 118 19 64 54 0.25 0.49
Pilot operated
MS 103 5/8" UNF 10 mm, 3/8" 84 12 79 54 0.51 0.75
MS 103MMS 10 mm ODF 10 mm 159 12 79 54 0.55 0.79
MS 103S 3/8" ODF 3/8" 159 12 79 54 0.55 0.79
MS 104 MMS 12 mm ODF 12 mm 159 12 79 54 0.56 -
MS 104S 1/2" ODF 1/2" 159 12 79 54 0.56 -
MS 124 3/4" UNF 12 mm, 1/2" 91 12 79 54 0.54 0.77
MS 124MMS 12 mm ODF 12 mm 159 12 79 54 0.56 0.79
MS 124S 1/2" ODF 1/2" 159 12 79 54 0.56 0.79
16 mm,
MS 125S 16 mm, 5/8" 159 12 79 54 0.56 -
5/8" ODF
MS 165 7/8" UNF 16 mm, 5/8" 97 12 79 54 0.57 0.80
16 mm,
MS 165S 16 mm, 5/8" 159 12 79 54 0.59 0.82
5/8" ODF
22 mm,
MS 167S 22 mm, 7/8" 173 12 79 54 0.59 -
7/8" ODF
22 mm,
MS 227S 22 mm, 7/8" 262 22 88 54 1.45 1.65
7/8" ODF
MA MD MS

Series M
Installation
 Position of plunger tube should be from upright to  Voltage of coil and network must correspond.
horizontal position.  The flat spade terminals is the earth connection. The
 Arrow on valve body must correspond with flow direction. protective conductor must also be connected at the plant.
 Keep 45 mm distance clear above the valve for  Do not energize the coil before assembling on the valve
assembly/disassembly of coil. body.
 Fit solenoid valve so that it is drip proof.  All gaskets must be fitted carefully in order to achieve
 Solder valves: protection to IP65.
 Remove cap nut, coil and gaskets before soldering.  Tighten fixing screw of connector.
 Max. temperature of valve body: 125 °C.  Constructive modifications at the valve are not allowed.
 When soldering, always point flame away from valve

body.
 When assembling after soldering, fit the coil’s top and
bottom seal rings.
 Flare valves:
 When tightening flare nuts grip at wrench flats on the
valve body provided for this purposes.
 Do not use coil and plunger tube as lever (thin-walled
plunger tube).
 When installing direct operated valves with 20 W DC
coil, the flare nut must be tightened in that way that one
flat of the nut is in parallel with the lower surface of the
coil.

Series RV
CHECK VALVES
FOR ALL FLUORINATED REFRIGERANTS
PRODUCT DATA
Features
 Hermetically welded type
 Copper plated solder connections
not for ammonia
Specification
Nominal capacity range see table on page 104
32.5 bar(a) (RV-07S)
11 bar(a) at t < -20 °C
Maximum test pressure PF 61.5 bar(a)
46.5 bar(a) (RV-07S)
15.7 bar(a) at t < -20 °C
Maximum temperature 120 °C
Minimum temperature -40 °C
Application
Check valves series RV are installed in the liquid line, hot gas
line or suction line of a refrigerated plant to permit the flow of
the refrigerant only in one direction. This is realised by a
spring-loaded piston which opens the valve only in one
direction.
Materials
Housing, piston brass
Sealing material Teflon
Connection tubes copper plated brass

Series RV
Capacities
Type P* kv- QN (kW)
(bar) value
Liquid line Suction gas line Hot gas line
(m3/h)
R22 R134a R404A R407C R22 R134a R404A R407C R22 R134a R404A R407C
R507A R410A R507A R410A R507A R410A
RV-02 MMS
0.06 0.37 6.7 6.2 4.4 6.2 1.0 0.8 0.8 1.0 4.4 3.2 3.7 4.7
RV-02 S
RV-03 MMS
0.06 1.75 31.7 29.3 20.8 29.2 4.7 3.8 3.8 4.5 20.8 15.1 17.5 22.2
RV-03 S
RV-04 MMS
0.05 3.27 59.2 54.8 38.9 54.6 8.8 7.1 7.1 8.4 38.0 28.3 32.7 40.6
RV-04 S
RV-05 S 0.05 3.64 65.9 61.0 43.3 60.7 9.8 7.9 7.9 9.3 43.3 31.5 36.4 46.3
RV-07 S 0.03 7.50 136.4 126.4 89.5 125.7 20.5 16.3 17.0 19.5 87.5 63.8 75.0 93.5
* P = min. pressure drop at which the valve is completely open
The nominal capacity QN as mentioned in table above refers to the following conditions:
Liquid and suction gas:
evaporating temperature to: +4 °C
condensing temperature tc: +38 °C
pressure drop: 0.15 bar
Hot gas:
temperature of hot gas: +85 °C
pressure drop: 1.0 bar

Type Connection Dimensions (mm) Weight
(A) B C D L (kg)
RV-02 MMS 6 mm ODF 42 22 18 95
approx. 0.05
RV-02 S 1/4" ODF 42 22 18 95
RV-03 MMS 10 mm ODF 42 22 18 95
approx. 0.05
RV-03 S 3/8" ODF 42 22 18 95
RV-04 MMS 12 mm ODF 48 28 27 117
approx. 0.15
RV-04 S 1/2" ODF 48 28 27 117
16 mm ODF
RV-05 S 48 28 27 117 approx. 0.20
5/8" ODF
22 mm ODF
RV-07 S 72 72 35.5 186 approx. 0.25
7/8" ODF

Series SLI/SBI
SIGHT GLASSES
WITH MOISTURE INDICATOR
PRODUCT DATA
Features
 Large display area
 Moisture indicator
 Low pressure loss
 SLI with solder connections on both sides
 SBI with flare connections on both sides
SLI
 SBIA with flare connections,
female thread x male thread
 Refrigerants: all CFC, HCFC, HFC,
not for R12, R502 and ammonia
Specifications
SBI Moisture indicator range see table on page 106
Max. ambient temperature TS 80 °C
Diameter display area 22.5 mm
Maximum Maximum
Type
SBIA pressure PS test pressure PF
SLI 6; SLI 1/4
SLI 10; SLI 3/8
SLI 12; SLI 1/2 44 bar(a) 63 bar(a)
Application SLI 15
Sight glasses series SLI/SBI/SBIA show the condition of the SLI 16 (5/8)
refrigerant flowing through the lines in the refrigerating plant,
SLI 18; SLI 3/4
for example it is possible to see if the refrigerant in the liquid
line is free of bubbles. SLI 22 (7/8)
36 bar(a) 51.5 bar(a)
The moisture indicator shows the moisture content in the SBI
refrigerant. SBIA
SLI 28; SLI 1 1/8 35 bar(a) 50 bar(a)
Materials
Housing brass
Display area pressure resistant glass,
indicator paper
Connection tubes Solder: copper
Flare: brass

Series SLI/SBI
Moisture Indicator
The colour of the indicator is a measure for the moisture load Green colour: Moisture free.
of the refrigerant inside the plant. Only a moisture-free refrigerant assures no trouble with the
The range of indication depends on the refrigerant: expansion valve coming from humidity.
Refrigerant Indication Range Transition range:

dry (green) Transition wet (yellow) When the green colour begins to fade, it is an indication that
R22 < 30 ppm 30 – 150 ppm > 150 ppm small quantities of moisture are present. It is recommended to
change the filter drier.
R134a < 60 ppm 60 – 100 ppm > 100 ppm
R404A < 20 ppm 20 – 100 ppm > 100 ppm Yellow colour: Wet.
R407C < 20 ppm 20 – 130 ppm > 130 ppm The refrigerant is loaded with moisture higher than the stated
R410A < 40 ppm 40 – 150 ppm > 150 ppm values. A change of the filter drier is required.
R507A < 20 ppm 20 – 100 ppm > 100 ppm
Due to the humidity in the air, the indicator is yellow on
Indication temperature: 30 °C
delivery. After the installation inside the plant, the indicator
will change to green when filling the system with dry
refrigerant.

Dimensions
Weight
Type Connection Pipe diameter Length approx. (kg)
(A) (B) (L)
SLI 6 6 mm ODF 6 mm 106 mm 0.15
SLI 10 10 mm ODF 10 mm 119 mm 0.15
SLI 12 12 mm ODF 12 mm 144 mm 0.20
SLI 15 15 mm ODF 15 mm 146 mm 0.17
SLI 16 16 mm; 5/8" ODF 16 mm; 5/8" ODF 146 mm 0,17
SLI 18 18 mm ODF 18 mm 183 mm 0.22
SLI 22 22 mm; 7/8" ODF 22 mm; 7/8" ODF 183 mm 0,24
SLI 1/4 1/4" ODF 1/4" 106 mm 0.15
SLI 3/8 3/8" ODF 3/8" 119 mm 0.15
SLI 1/2 1/2" ODF 1/2" 144 mm 0.19
SLI 3/4 3/4" ODF 3/4" 183 mm 0.22
SLI 1 1/8 1 1/8" ODF 1 1/8" 188 mm 0.48
SBI 6 7/16" UNF 6 mm 1/4" 70 mm 0.15
SBI 10 5/8" UNF 10 mm 3/8" 76 mm 0.15
SBI 12 3/4" UNF 12 mm 1/2" 88 mm 0.17
SBI 16 7/8" UNF 16 mm 5/8" 98 mm 0.29
SBIA 6 7/16" UNF 6 mm 1/4" 60 mm 0.30
SBIA 10 5/8" UNF 10 mm 3/8" 76 mm 0.15
SBIA 12 3/4" UNF 12 mm 1/2" 74 mm 0.19
SBIA 16 7/8" UNF 16 mm 5/8" 78 mm 0.31

SLI
SBI SBIA

Series SLI/SBI

S B I A 12
Series
Connection type:
B = flare
L = solder
Indicator
A = Inner and outer connection
()
Tube connection size (mm, inch)

Series FF
FILTER DRIERS
PRODUCT DATA
Features
 Liquid line filter drier
 Drying agent in bulk
 Solder or flare connections
 FF ...MMS: solder connection in mm
 FF ...S: solder connection in inch
 FF ...: flare connection
not for ammonia
Specification
Nominal capacity see tables on page 110
Water adsorption see table on page 111
40 bar(a) (for FF 410)
11 bar(a) at t < -20 °C
Maximum test pressure PF 61.5 bar(a)
57.2 bar(a) (for FF 410)
Application 15.7 bar(a) at t < -20 °C
Filter driers series FF are used for filtration of impurities by Max. operating temperature 80 °C
microscopic filters and to take away moisture from the
refrigerant. Min. operating temperature -40 °C
The filter driers are placed in the liquid line of airconditioning,
refrigeration and deep freeze systems. Installation
 Any mounting position in the liquid line.
Materials  Flow in direction of arrow!
Housing steel  When soldering the filter drier, the housing must not get
Internals steel warmer than 160 °C.
Drier molekularsieve, activated alumina  Constructive modifications at the filter drier are not
allowed.
Connections solder: copper, copper plated steel or
steel**
flare: nickel plated steel

Series FF
Capacities, Dimensions and Weights

Filter drier with solder connections
Type Nominal cooling capacity Connections Dimensions Weight
(kW)* ODF D L VF (kg)
(d)
R134a R22 R404A R407C R410A (mm) (mm) (dm3)
R507A
FF 032MMS 9.8 10.7 7.0 10.1 10.6 6 mm 52 98.5 0.1 0.26
FF 032S 9.8 10.7 7.0 10.1 10.6 1/4" 52 98.5 0.1 0.26
FF 052MMS 9.6 10.5 6.8 9.9 10.4 6 mm 52 111.5 0.1 0.295
FF 052S 9.6 10.5 6.8 9.9 10.4 1/4" 52 111.5 0.1 0.295
FF 053MMS 23.3 25.4 16.6 23.9 25.0 10 mm 52 111.5 0.1 0.325
FF 053S 23.3 25.4 16.6 23.9 25.0 3/8" 52 111.5 0.1 0.325
FF 082MMS 9.1 9.9 6.5 9.3 9.7 6 mm 52 139.5 0.2 0.37
FF 082S 9.1 9.9 6.5 9.3 9.7 1/4" 52 139.5 0.2 0.37
FF 083MMS 22.7 24.8 16.1 23.3 24.4 10 mm 52 139.5 0.2 0.405
FF 083S 22.7 24.8 16.1 23.3 24.4 3/8" 52 139.5 0.2 0.405
FF 084MMS 30.2 33.0 21.5 31.1 32.6 12 mm 52 139.5 0.2 0.465
FF 084S 30.2 33.0 21.5 31.1 32.6 1/2" 52 139.5 0.2 0.465
FF 162MMS 8.8 9.6 6.2 9.0 9.4 6 mm 74 159 0.4 0.825
FF 162S 8.8 9.6 6.2 9.0 9.4 1/4" 74 159 0.4 0.825
FF 163MMS 22.7 24.8 16.1 23.3 24.4 10 mm 74 159 0.4 0.875
FF 163S 22.7 24.8 16.1 23.3 24.4 3/8" 74 159 0.4 0.875
FF 164MMS 33.6 36.6 23.9 34.5 36.1 12 mm 74 159 0.4 0.93
FF 164S 33.6 36.6 23.9 34.5 36.1 1/2" 74 159 0.4 0.93
FF 165S 47.8 52.1 34.0 49.1 51.4 16 mm - 5/8" 74 163 0.4 0.96
FF 303MMS 22.7 24.8 16.1 23.3 24.4 10 mm 74 235.5 0.6 1.305
FF 303S 22.7 24.8 16.1 23.3 24.4 3/8" 74 235.5 0.6 1.305
FF 304MMS 33.6 36.6 23.9 34.5 36.1 12 mm 74 235.5 0.7 1.35
FF 304S 33.6 36.6 23.9 34.5 36.1 1/2" 74 235.5 0.7 1.35
FF 305S 47.8 52.1 34.0 49.1 51.4 16 mm - 5/8" 74 239.5 0.7 1.41
FF 307S** 64.7 70.6 46.0 66.5 69.7 22 mm - 7/8" 74 259.5 0.6 1.45
FF 414MMS 38.8 42.4 27.6 39.9 41.8 12 mm 93 232.5 1.1 2.035
FF 414S 38.8 42.4 27.6 39.9 41.8 1/2" 93 232.5 1.1 2.035
FF 415S 60.5 66.0 43.0 62.2 65.1 16 mm - 5/8" 93 245.5 1.1 2.105
FF 417S** 84.1 91.7 59.8 86.4 90.5 22 mm - 7/8" 93 278.5 1.2 2.110
Filter drier with flare connections

Type Nominal cooling capacity Connectios Dimensions Weight
(kW)* UNF D L VF (kg)
(d)
R134a R22 R404A R407C R410A (mm) (mm) (dm3)
R507A
FF 032 5.7 6.3 4.1 5.9 6.2 7/16" 52 108.5 0.1 0.26
FF 052 5.6 6.1 4.0 5.8 6.1 7/16" 52 121.5 0.1 0.295
FF 053 18.6 20.3 13.3 19.2 20.1 5/8" 52 127.5 0.1 0.325
FF 082 5.3 5.8 3.8 5.5 5.8 7/16" 52 149.5 0.2 0.37
FF 083 18.1 19.8 12.9 18.7 19.6 5/8" 52 155.5 0.2 0.405
FF 084 28.7 31.4 20.4 29.5 30.9 3/4" 52 159.5 0.2 0.465
FF 162 5.2 5.7 3.7 5.3 5.6 7/16" 74 169 0.4 0.825
FF 163 17.7 19.3 12.6 18.2 19.1 5/8" 74 175 0.4 0.875
FF 164 31.1 33.9 22.1 32.0 33.5 3/4" 74 179.5 0.4 0.93
FF 165 44.4 48.4 31.6 45.6 47.8 7/8" 74 183.5 0.4 0.96
FF 303 17.7 19.3 12.6 18.2 19.1 5/8" 74 251.5 0.6 1.305
FF 304 31.1 33.9 22.1 32.0 33.5 3/4" 74 255.5 0.7 1.35
FF 305 44.4 48.4 31.6 45.6 47.8 7/8" 74 259.5 0.7 1.41
FF 414 36.3 39.7 25.9 37.4 39.2 3/4" 93 252.5 1.1 2.035
FF 415 56.6 61.8 40.3 58.2 61.0 7/8" 93 265.5 1.1 2.105
* Capacities are based on to = -15 °C, tc = +30 °C and pressure drop p = 0.07 bar.
** Steel connections

Filter drier with solder connections
Filter drier with flare connections
Water adsorption rate

Water adsorption rate (g)
Refrigerant R134a R22 R404A R407C R410A
R507A
Final moisture 50 ppm 60 ppm 50 ppm 50 ppm 50 ppm
Liquid tempera-
24 °C 52 °C 24 °C 52 °C 24 °C 52 °C 24 °C 52 °C 24 °C 52 °C
ture
030 4.0 3.7 3.9 3.6 4.3 4.0 3.6 3.1 2.5 2.3
050 7.8 7.2 7.5 6.9 8.3 7.7 7.0 5.9 4.8 4.4
080 12.6 11.6 12.1 11.1 13.4 12.4 11.2 9.6 7.7 7.0
Type
160 25.1 23.2 24.1 22.2 26.7 24.8 22.4 19.1 15.3 14.1
300 48.5 44.8 46.7 42.9 51.7 47.9 43.2 37.0 29.7 27.2
410 67.2 62.0 64.6 59.4 71.6 66.4 59.9 51.2 41.0 37.7

Series FF

FF 16 4 MMS
Series
Filter size
Tube connection size in 1/8‘‘
Connection type:
() = flare
S = solder in inch
MMS = solder in mm

Series SA
VIBRATION ABSORBERS
FROST RESISTANT CONSTRUCTION, LASER WELDED
PRDUCT DATA
Features
 Short connection fittings
 Compact construction
 Flexible pipe, braid and shoulder made of stainless
steel
 Frost resistant construction - no collecting of
condensation water within the corrugated area
 Suitable for vertical installation
 Laser welded
 Connection fittings made of copper
 No preventive measures from overheating necessary
when soldering
not for ammonia
Specification
Maximum test pressure PF 1.5 x PS
Maximum temperature 250 °C
Minimum temperature -100 °C
Application
Vibration absorbers series SA are installed in refrigerated
plants to minimize vibrations on the pipes caused by the
compressor. Furthermore they decrease noise and
compensate small thermal displacements.
Materials
Flexible pipe stainless steel
Braid stainless steel
Shoulder stainless steel
Connection fittings copper

Series SA

Type Connection Dimensions (mm) Weight
(A) B C D L (kg)
6 mm ODF 230
SA06-1/4 1.0 20 19 approx. 0.11
1/4" ODF
SA08 8 mm ODF 1.0 20 19 230 approx. 0.11
SA3/8 3/8" ODF 1.0 20 19 230 approx. 0.11
SA10 10 mm ODF 1.0 20 19 230 approx. 0.12
SA12 12 mm ODF 1.0 20 21 230 approx. 0.13
SA1/2 1/2" ODF 1.0 20 21 230 approx. 0.13
SA15 15 mm ODF 1.0 25 27 255 approx. 0.17
16 mm ODF 255 approx. 0.17
SA16-5/8 1.0 25 27
5/8" ODF
SA18 18 mm ODF 1.0 25 27 255 approx. 0.17
SA3/4 3/4" ODF 1.0 25 27 255 approx. 0.17
SA22-7/8 1.5 25 32
7/8" ODF
SA28-1 1/8 1.5 25 39
1 1/8" ODF
SA35-1 3/8 2.0 30 48
1 3/8" ODF
SA42-1 5/8 2.0 35 58
1 5/8" ODF
54 mm ODF
SA54-2 1/8 2.5 45 70 510 approx. 1.68
2 1/8" ODF

Notes

Notes

Notes

Notes

Nomenclature
Solenoid valves
M A 06 2 MMS
M D 10 3 S MA MD MS
M S 16 5
() = Flare, MMS = solder in mm, S = solder in inch
Connections Connection size in 1/8‘‘
Valve size
Type A = angle – direct operated, D = direct operated, S = pilot operated
Product Solenoid valve
Sight glasses SBI

S L I 1/2
S B I 10 SBIA
SLI
S B I A 12
Connection size (mm, inch)
A = inner and outer
Indicator
Connections L = solder, B = flare
Product Sight glass
Filter driers
FF 05 2
FF
FF 08 3 S
FF 16 4 MMS
() = Flare, MMS = solder in mm, S = solder in inch
Connection Connection size in 1/8‘‘
Filter size
Product Filter drier
Electronic Controls
P TI 6 10
P CR 1 10
PCR-110
P CR 3 00 RC PCR-100 PTI-610
P CR 4 10
Real time Clock

installation
00 = DIN rail, 10 = snap-in
type
no. of outputs (not for PTI)
Temperature Indicator, ContRoller
Product P = electronic controller series

Automatic Expansion Valves
A E L
A MV X
AMVX AMV
A MV AEL
Connections L = solder AMV(X) only flare connections
Pressure equaliser () = internal, eXternal
Series of valve E MV
Product Automatic Expansion Valve
Thermostatic Expansion Valves Orifice cartridges

with interchangeable orifice AMV(X)
T MV TMV(X)
TMV(X)BL
T MV X TMVL
TMVBL NMVL VD
T MV BL TMV
T MV X BL TMVL Orifice cartridges

TMX
T MV L NMX
TMVX
T M X TMVXBL TMX
Connections L = solder, B = flare XD
Series of valve MV M
Product Thermostatic Expansion Valve
Solder bases for series TMVL and NMVL Löt/Bördelsockel für Typenreihe TMX und NMX
two-way angle Two-way angle
XLS
VLS
VLSX VLS XBS XLS

VLSX
Thermostatic Expansion Valves
with fixed orifice
T L K
T L E
T L E X TBEX TLEX 4.75-7

TLEX 0.5-4.5
TLK
T B E X
T O E X
T L ES X TOEX
TLE TLEX 8-11 TLESX
Series of valve K E ES
Connections L = solder, B = flare, O =O-Ring
Product Thermostatic Expansion Valve

Honeywell Product Portfolio
EN0H-0376GE23 R0912 · Subject to change without notice

121
Our online service
On the internet you can find

detailed information about the
cooling components of
Honeywell.
www.honeywell-cooling.com
• Link Products
Technical information, data
sheets, mounting guidelines
and certificates to download
• Link Selection Software
Selection software „Valve Tool“
to download and for free usage
• Link Contacts
Request of additional
information, world-wide
contacts
Please note:
Do you prefer to have that
information on CD? Then please
order your personal copy by
sending an E-mail to (do not
forget to mention your address):
cooling.mosbach@honeywell.com
Automation and Control Solutions

Honeywell GmbH
Hardhofweg
74821 Mosbach/Germany
Phone: +49 (0) 62 61 / 81-212 and +49 (0) 6261 / 81-472
Fax: +49 (0) 62 61 / 81-520
cooling.mosbach@honeywell.com
EN0H-0376GE23 R1014
Subject to change without notice
www.honeywell-cooling.com © 2014 Honeywell GmbH

Product Catalogue

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Catalogue

Uploaded by

Copyright:

Available Formats

Product Catalogue

EN0H-0376GE23 R1014 · Subject to change without notice 3

Series Description Page

EEV Electronic Expansion Valves 9

SHC Electronic Superheat Controllers 15

ESDR Electronic Suction Pressure Regulation Valves 25

PCR Electronic Thermostats and Cold Store Controls 29

PTI Electronic Temperature Display 35

AMV Automatic Expansion Valves 37

AMVX Automatic Expansion Valves 37

AEL Automatic Expansion Valves 41

TMV Thermostatic Expansion Valves 43

4 EN0H-0376GE23 R1014 · Subject to change without notice

TMVX Thermostatic Expansion Valves 43

TMVBL Thermostatic Expansion Valves 43

TMVXBL Thermostatic Expansion Valves 43

TMVL Thermostatic Expansion Valves 47

VD Orifice Cartridge for Thermostatic Expansion Valves TMV, TMVL and 43

EN0H-0376GE23 R1014 · Subject to change without notice 5

Series Description Page

TMX Thermostatic Expansion Valves 51

XD Orifice Cartridge for Thermostatic Expansion Valves TMX and NMX 51

TLK Thermostatic Expansion Valves 55

TLE 0.5 - 3.0 Thermostatic Expansion Valves 59

TLEX 0.5 - 4.5 Thermostatic Expansion Valves 59

TBEX 0.5 - 4.5 D Thermostatic Expansion Valves 63

6 EN0H-0376GE23 R1014 · Subject to change without notice

TOEX 0.5 -4.5 D Thermostatic Expansion Valves 67

TLESX 4.75 - 6 Thermostatic Expansion Valves 71

TLEX 4.75 - 7 Thermostatic Expansion Valves 75

CVC Hot Gas Bypass Valves 83

HLE Hot Gas Bypass Valves 83

HLEX 4.75 - 7 Hot Gas Bypass Valves 85

NMVL Liquid Injection Valves 89

NMX Liquid Injection Valves 89

EN0H-0376GE23 R1014 · Subject to change without notice 7

MC Coil for Solenoid Valves MA, MD, MS 95

RV Check Valves 103

SBI Sight Glasses 105

SBIA Sight Glasses 105

SLI Sight Glasses 105

FF Filter Driers 109

SA Vibration Absorber 113

8 EN0H-0376GE23 R1014 · Subject to change without notice

Operating Temperature Medium: -40 ... +75 °C

EN0H-1952GE23 R1014 · Subject to change without notice 9

Cooling Capacity QN (kW)

Cooling Capacity QN (kW)

10 EN0H-1952GE23 R1014 · Subject to change without notice

EN0H-1952GE23 R1014 · Subject to change without notice 11

3/8 x 1/2 = 3/8” x 1/2” ODF

12 EN0H-1952GE23 R1014 · Subject to change without notice

EN0H-1952GE23 R1014 · Subject to change without notice 13

Stepper motor outputs

MU0B-0639GE51 R0410 · Subject to change without notice 15

Function Valve Control

Terminal Connection Diagram

CONNECTION OF THE RELEASE/ENABLER SIGNAL (DI1, FACTORY DEFAULT)

16 MU0B-0639GE51 R0410 · Subject to change without notice

4 EARTH earth / shielding

12 C4 relay 4, change-over contact

21 T1 AIN1: temperature input 1 (NTC10K, NTC20K, Pt1000)

28 R2 AIN6: current/voltage input 2 (0.5…4.5 V, 0…10 V, 4…20 mA)