Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 303 views

    Bacnet/Modbus Carrier Translator Installation Instructions

    Uploaded by

    marcyel Oliveira Woliveira
    The document provides installation instructions for a Carrier Translator module that allows communication between Carrier CCN controllers and third party BACnet/Modbus networks. The module converts CCN protocol to Modbus RTU and BACnet MS/TP. It is installed by connecting a 24V power supply, wiring the CCN communication port to a CCN controller, and connecting the removable RS-485 port to the third party BACnet/Modbus network. Status LEDs indicate power, CCN activity, and RS-485 communication.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Bacnet/Modbus Carrier Translator Installation Instructions

    Uploaded by

    marcyel Oliveira Woliveira
    303 views3 pages
    The document provides installation instructions for a Carrier Translator module that allows communication between Carrier CCN controllers and third party BACnet/Modbus networks. The module converts CCN protocol to Modbus RTU and BACnet MS/TP. It is installed by connecting a 24V power supply, wiring the CCN communication port to a CCN controller, and connecting the removable RS-485 port to the third party BACnet/Modbus network. Status LEDs indicate power, CCN activity, and RS-485 communication.

    Original Title

    997-050010-1

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides installation instructions for a Carrier Translator module that allows communication between Carrier CCN controllers and third party BACnet/Modbus networks. The module converts CCN protocol to Modbus RTU and BACnet MS/TP. It is installed by connecting a 24V power supply, wiring the CCN communication port to a CCN controller, and connecting the removable RS-485 port to the third party BACnet/Modbus network. Status LEDs indicate power, CCN activity, and RS-485 communication.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    303 views3 pages

    Bacnet/Modbus Carrier Translator Installation Instructions

    Uploaded by

    marcyel Oliveira Woliveira
    The document provides installation instructions for a Carrier Translator module that allows communication between Carrier CCN controllers and third party BACnet/Modbus networks. The module converts CCN protocol to Modbus RTU and BACnet MS/TP. It is installed by connecting a 24V power supply, wiring the CCN communication port to a CCN controller, and connecting the removable RS-485 port to the third party BACnet/Modbus network. Status LEDs indicate power, CCN activity, and RS-485 communication.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    BACnet/Modbus Carrier Translator

    Installation Instructions
    The CCN Carrier Translator module with RS-485 serial communication (33CNTRAN485), shown
    below, is a microcontroller-based module that provides the ability to easily interface Carrier CCN
    controllers to third party non-Carrier control equipment. The BACnet/Modbus Carrier Translator
    provides CCN to Modbus Remote Terminal Unit (RTU) and BACnet Master-Slave/Twisted-Pair
    (MS/TP) protocol conversion.

    RS-485 LED Status LED Isolated RS-485 Connector (BACnet/Modbus) CCN LED
    (1) RS485+ (2) RS485 G (3) RS485-

    Ground + CCN- CCN Gnd CCN+


    24 Vac 24 Vac CCN Communication Connector

    997-050010-1 Page 1 of 3
    01/05
    Installation Procedure
    1. Install the Carrier Translator printed circuit board into the equipment’s CCN controls section and
    secure by inserting 4 sheet metal screws through the board’s integrated standoffs.
    2. Connect a field supplied 24 Vac (3 VA minimum) transformer to the power connector.

    Note 1: The power can be shared with a single CCN controller’s 24 Vac transformer provided
    that you ensure there is sufficient VA available on the existing transformer. The
    Carrier Translator provides an isolated communications port that allows for power
    sharing with one other Carrier CCN controller that utilizes 24 Vac. When sharing
    power, make sure that the polarity of the power wires into the Carrier Translator (24
    Vac + and Ground) are the same as at the source controller.

    Note 2: It is recommended that you provide a way to cycle power to the Carrier Translator
    without disconnecting wires.

    Table 1
    Carrier Translator
    Power Connector
    Connector Signal
    Terminal Assignment
    + Supply Hot
    Supply Common

    3. If the CCN network consists solely of this Carrier Translator and its associated CCN controller,
    wire the Carrier Translator’s non-removable CCN communication connector to the CCN
    controller’s CCN communication connector.

    If the CCN network consists of multiple Carrier Translators and multiple associated CCN
    controllers, wire the CCN communication bus in accordance with all CCN network standards
    and address the Carrier Translators and CCN controllers appropriately.

    Table 2
    CCN Connector Carrier Translator Equipment
    Terminal Assignment Connector Connector Signal

    + 1 CCN Data (+)


    G 2 CCN Signal Ground
    - 3 CCD Data (-)

    4. Wire the Carrier Translator’s removable RS-485 communication connector to the third party’s
    Modbus or BACnet MS/TP communication network as instructed by the third party
    representative.

    997-050010-1 Page 2 of 3
    01/05
    LEDs
    The BACnet/Modbus Carrier Translator has three LEDs that are used to indicate operational status:

    LED Color Indicates

    Status Red Operating, initialization and configuration status. The LED blinks at a 2
    Hz rate when initializing and at 1 Hz when operating correctly.

    CCN Yellow The Carrier Translator is sending CCN communication messages to the
    connected CCN controller. If the connected CCN controller is responding,
    its CCN LED will blink when a message is sent back to the Carrier
    Translator.

    RS-485 Green The Carrier Translator is sending RS-485 communication messages to the
    Modbus or BACnet MS/TP network.

    997-050010-1 Page 3 of 3
    01/05

    You might also like