Seer Light Ambulatory Recorder/Controller: Service Manual

SEER® Light
Ambulatory Recorder/Controller
Service Manual
Software Version 1
2019818-008 Revision B
Service Instructions for:
SEER Light/SEER Light Extend Compact Digital Holter Recorder
SEER Light/SEER Light Extend Controller
SEER Light Connect

NOTE: The information in this manual only applies to SEER Light devices software version 1. It does not
apply to earlier software versions. Due to continuing product innovation, specifications in this manual are
subject to change without notice.
Marquette®, MARS®, MUSE®, and SEER® are trademarks owned by GE Medical Systems Information
Technologies, a General Electric Company going to market as GE Healthcare. All other marks are owned by
their respective owners.
© 2005 General Electric Company. All rights reserved.
T-2 SEER Light Ambulatory Recorder/Controller Revision B

2019818-008 15 July 2005
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Manual Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Manual Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Disposal of the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Responsibility of the Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Information Technology Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Equipment Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
2 SEER Light/SEER Light Extend Recorder . . . . . . . . . . . 2-1

Component Names and Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Self-Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
No Buzzer Sound After Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . 2-6
Beep Sound Will Not Stop After Installing the Batteries . . . . . . . . . . . . . . . . 2-7
ECG Cannot Be Previewed with Controller (I.R.) . . . . . . . . . . . . . . . . . . . . . 2-8
ECG Cannot be Previewed with Controller (Cable) . . . . . . . . . . . . . . . . . . . . 2-9
ECG Cannot Be Previewed with SEER Light Connect Device . . . . . . . . . . 2-10
Recording Cannot Start with the Controller (I.R.) . . . . . . . . . . . . . . . . . . . . 2-11
Recording Cannot Start with the SEER Light Connect Device . . . . . . . . . . 2-12
Cannot Start by Pressing the Start Button . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Cannot Record for 24 Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Cannot Record for 48 Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Cannot Transfer Data from the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Revision B SEER Light Ambulatory Recorder/Controller i

2019818-008
Cannot Transfer Data from the Recorder to the
SEER Light Connect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Record Start Date/Time is Initialized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Artifact on ECG Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Cannot Detect Pacemaker Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
3 SEER Light/SEER Light Extend Controller . . . . . . . . . . . 3-1

Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
No Operation After Inserting Batteries and Pressing Power Button . . . . . . . . . . . 3-6
ECG Cannot be Previewed with the Controller (I.R.) . . . . . . . . . . . . . . . . . . . . . . . 3-7
ECG Cannot be Previewed by the Controller (Cable) . . . . . . . . . . . . . . . . . . . . . . 3-8
Cannot Start Recording (I.R.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Pressing the Appropriate Key(s) Does Not Start Operation . . . . . . . . . . . . . . . . . 3-10
Beep Sounds While the Flash Card is Inserted . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Data Cannot be Transferred from the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Recording Start Date/Time is Not Correct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Time is Not Correct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
4 SEER Light Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
ECG Cannot Be Previewed with SEER Light Connect Device . . . . . . . . . . . 4-5
Recording Cannot Start with the SEER Light Connect Device . . . . . . . . . . . 4-6
Cannot Transfer Data from the Recorder to the
SEER Light Connect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Recording Start Date/Time is Not Correct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Visual Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
ii SEER Light Ambulatory Recorder/Controller Revision B

2019818-008
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Cleaning Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Storing the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Maintenance/Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Maintenance/Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .A-1

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
SEER Light/SEER Light Extend Ambulatory Recorder . . . . . . . . . . . . . . . . . . . . .A-3
SEER Light Ambulatory Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4
SEER Light Connect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-5
Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . .B-1

Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions . . . . . . .B-3
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity . . . . . . . .B-4
Recommended Separation Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-6
Compliant Cables and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1
Revision B SEER Light Ambulatory Recorder/Controller iii

2019818-008
iv SEER Light Ambulatory Recorder/Controller Revision B
2019818-008
1 Introduction
Revision B SEER Light Ambulatory Recorder/Controller 1-1

2019818-008
For your notes
1-2 SEER Light Ambulatory Recorder/Controller Revision B

2019818-008
Introduction: Manual Information
Manual Information
Revision History
Each page of the document has the document part number followed by a
revision letter at the bottom of the page. This letter identifies the
document’s update level. The latest letter of the alphabet corresponds to
the most current revision of the document.
The revision history of this document is summarized in the table below.
Table 1. Revision History 2019818-008
Revision Date Comment
A 15 May 2005 Initial release of manual.
B 15 July 2005 Manual updated for clarity.
Manual Purpose
This manual supplies technical information for service representative
and technical personnel so they can maintain the equipment. Use it as a
guide for maintenance and electrical repairs considered field repairable.
Where necessary the manual identifies additional sources of relevant
information and or technical assistance.
See the operator manual for the instructions necessary to operate the
equipment safely in accordance with its function and intended use.
Definitions
Items shown in Black text are keys on the keyboard, text to be
entered, or hardware items such as buttons or switches on the
equipment.
Items shown in Italicized text are software terms which identify

menu items, buttons, or options in various windows.
To perform an operation which appears with a plus (+)sign between

the names of two keys, you press and hold the first key while
pressing the second key once. This is called a keystroke combination.
For example, “Press Ctrl + Esc” means to press and hold down the
Ctrl key while pressing the Esc key.
When instructions are given for typing a precise text string with one
or more spaces, the point where the spacebar must be pressed is
indicated as: <Space>. The purpose of the < > brackets is to ensure
you press the spacebar when required.

2019818-008
Introduction: Manual Information
Enter means to press the “Enter” or “Return” key on the keyboard.

Do not type “enter”.

2019818-008
Introduction: Related Manuals
Related Manuals
See the documents listed below for additional information.
Table 2. SEER Light Documents
Part Number Name

2019818-007 SEER Light Ambulatory Recorder/Controller Operator’s Manual

2019818-008
Introduction: Safety Information
Safety Information
Intended Use
The SEER Light recorder is a two and three channel digital Holter ECG
recorder that records the electrical signals associated with cardiac
activity for 24 or 48 hours. It is used in diagnosing cardiac abnormalities
and revealing trends or changes in heart function. This device is for the
use of trained personnel only.
This device is not intended for use on infants weighing less than 10 kg
(22 lbs).
Definitions
The terms danger, warning, and caution are used throughout this
manual to point out hazards and to designate a degree or level of
seriousness. Familiarize yourself with their definitions and significance.
Hazard is defined as a source of potential injury to a person.
DANGER indicates an imminent hazard which, if not avoided, will

result in death or serious injury.
WARNING indicates a potential hazard or unsafe practice which, if not

avoided, could result in death or serious injury.
CAUTION indicates a potential hazard or unsafe practice which, if not

avoided, could result in minor personal injury or product/property
damage.
NOTE provides application tips or other useful information.
Warnings
WARNINGS
ACCIDENTAL SPILLS — If liquids have entered a

device, take it out of service and have it checked by a
service technician before it is used again. To avoid
electric shock or device malfunction liquids must not be
allowed to enter the device.
CABLES — To avoid possible strangulation, route all

cables away from patient's throat.
CARDIAC APPLICATION — This device cannot be used

for direct cardiac application.
CONDUCTIVITY — Keep the conductive parts of lead

electrodes and associated parts away from other
conductive parts, including earth.
DEFIBRILLATOR PRECAUTIONS — Do not come into

2019818-008
contact with patients during defibrillation. Otherwise,

serious injury or death could result. Patient signal inputs
labeled with the CF and BF symbols with paddles are
protected against damage resulting from defibrillation
voltages. To ensure proper defibrillator protection, use
only the recommended cables and leadwires. Proper
placement of defibrillator paddles in relation to the
electrodes is required to ensure successful defibrillation.
ELECTROSURGERY — If an electrosurgery device is

used, it is necessary to disconnect the patient cable from
the SEER Light recorder. Take precautions to reduce
risks of burns and injury to the patient.
LEAKAGE CURRENT — Electrical shock to patient

could result from component failure and lack of power
isolation.
In the event this system is used in the patient vicinity, it

must be configured in such a way that it and all of its
electrically-connected peripheral devices are isolated from
mains power to prevent excessive leakage current to the
patient. This can be accomplished through the use of
isolated mains power, or a medical grade isolation
transformer (in compliance with UL 60601, CAN/CSA
C22.2 No. 601.1, IEC 60601-1) with this system. All non-
medical peripheral devices shall comply with IEC and ISO
safety standards that are relevant to that equipment (i.e.,
IEC 60950, UL 60950).
Use of the SEER Light Connect device in the patient

vicinity requires that these measures are observed.
PACEMAKER PATIENTS — Take precautions to avoid

risks of hazard due to the operation of a cardiac
pacemaker or other electrical stimulators.
SUPERVISED USE — This device is intended for use

under the direct supervision of a licensed health care
practitioner.
Cautions
CAUTIONS
RESTRICTED SALE — U.S. federal law restricts this

device to sale by or on the order of a physician.
BEFORE OPERATION — Check that the instrument

operates properly.
DISPOSAL — At the end of its service life, the product

described in this manual, as well as its accessories, must
be disposed of in compliance with local, state, or federal

2019818-008
guidelines regulating the disposal of such products. If you

have questions concerning disposal of the product, please
contact GE or its representatives.
MODIFICATIONS — Do not make any modifications to

the device.
AFTER DEVICE USE — Clean the device after each use

to ensure trouble-free operation for the next use.
Use a piece of damp cloth with alcohol to clean the

device and the patient cable.
The device cannot be sterilized.
Do not use xylene and petrol related liquid for

cleaning the device.
To ensure proper operation of the device, it is

necessary to periodically have the device checked by
authorized service personnel.
Check the patient cable and connectors every month

by connecting them to an ECG simulator.
INSTALLATION — Adhere to the following

recommendations during installation:
Install and keep device away from splashing water.
Do not install the device where it may be affected by

humidity, ventilation, direct sunlight, air
conditioning, dust, salt, sulfur, etc.
Prevent the device from tilting, and protect it from

the possibility of vibration or shock.
Do not install the device in a chemical storage area or

where gas is generated.
Serial Number
Every GE Medical Systems Information Technologies device has a
unique serial number for identification. The serial number appears on
the device label similar to the one shown below.
50A

2019818-008
Disposal of the Device

When disposing the device, follow the applicable national rules and
regulations of disposal of medical equipment.
When disposing the recyclable battery, follow the applicable national

rules and regulations concerning the environmental issues.

2019818-008
Introduction: Responsibility of the Manufacturer
Responsibility of the Manufacturer
GE is responsible for the effects of safety, reliability, and performance

only if:
Assembly operations, extensions, readjustments, modifications, or

repairs are carried out by persons authorized by GE Medical Systems
Information Technologies.
The equipment is used in accordance with the instructions for use.
General
Refer equipment servicing to GE authorized service personnel only. Any
unauthorized attempt to repair equipment under warranty voids that
warranty.
It is the user’s responsibility to report the need for service to GE or to one

of its authorized agents.
This device is intended for use under the direct supervision of a licensed
health care practitioner.
To ensure patient safety, use only parts and accessories manufactured or

recommended by GE.
Contact GE for information before connecting any devices to this

equipment that are not recommended in this manual.
Parts and accessories used must meet the requirements of the applicable
IEC 60601 series safety standards, and/or the system configuration must
meet the requirements of the IEC 60601-1-1 medical electrical systems
standard.
The use of ACCESSORY equipment not complying with the equivalent

safety requirements of this equipment may lead to a reduced level of
safety of the resulting system. Consideration relating to the choice shall
include:
use of the accessory in the PATIENT VICINITY; and
evidence that the safety certification of the ACCESSORY has been

performed in accordance with the appropriate IEC 60601-1 and/or
IEC 60601-1-1 harmonized national standard.

2019818-008
Introduction: Responsibility of the Manufacturer
Information Technology Equipment

The hardware components supplied by GE for the MARS® Holter
analysis workstation, on which the SEER Light Connect application
runs, are considered to be Information Technology Equipment (ITE).
These individual components have been found to comply with the
standard for Safety of Information Technology Equipment, including
Electrical Business Equipment EN60950 (UL 60950).
The software used in the MARS® Holter analysis workstation is

considered as medical software. The software has been designed and
manufactured to the appropriate medical regulations and controls.
In order for the MARS® Holter analysis workstation to comply with

medical equipment standard leakage current requirements, a medical
grade uninterruptible power supply (UPS) must be used (UL 60601-1,
CSA 22.2 No. 60601-1, EN 60601-1) to power all non-medical equipment.
In addition, non-medical electrical equipment must comply with IEC and

ISO safety standards that are relevant to that equipment (i.e., IEC
60950, Safety of Information Technology Equipment.)

2019818-008
Introduction: Equipment Symbols
Equipment Symbols
The following symbols may appear on the equipment.
Attention. Consult accompanying documents.
Event.
This symbol indicates the polarity orientation that each battery should have when you insert it
into the unit. This unit requires you to insert the batteries so that the polarities are oriented in
alternating directions.
Power.
Stop.
Input connector.
Output connector.
This symbol indicates that the waste of electrical and electronic equipment must not be
disposed as unsorted municipal waste and must be collected separately. Please contact an
authorized representative of the manufacturer for information concerning the
decommissioning of your equipment.

2019818-008
2 SEER Light/SEER Light
Extend Recorder

2019818-008
For your notes

2019818-008
SEER Light/SEER Light Extend Recorder: Component Names and Locations
Component Names and Locations
Structure
The SEER Light ambulatory recorder is shown and described below.
A B
.60 in. 3.35 in.

(15 mm) (85 mm)
I 2.17 in.(55 mm)
C J
F E D 017A
Table 3. SEER Light Ambulatory Recorder
Item Name Description
A REC LED To display operation conditions:

After pressing the start/event button, the LED will flash twice per second for three
minutes. During this time data is not recorded.
During recording, the LED will flash every second.
B Use to start recording.

start/event button Use to mark events during recording.
C battery compartment cover Slide the cover to open and set the batteries in the battery compartment.
D For transfer of data to the SEER Light controller or to the SEER Light Connect device.
A data output
connector
E access LED Will flash during communication with the SEER Light controller.
F infrared terminal (I.R. Window) Used to receive the signal from the SEER Light controller to begin ECG recording.
Used to receive patient information and ECG recording starting time.
Used to confirm the ECG waveform recorded by the recorder (ECG preview).
G Not used.
B output connector
H DATA LED The LED flashes while transferring data to the SEER Light controller.

2019818-008
SEER Light/SEER Light Extend Recorder: Component Names and Locations
Table 3. SEER Light Ambulatory Recorder (Continued)
I patient cable connector Used to connect patient cable for ECG input.
J Stop button Push to stop recording

2019818-008
SEER Light/SEER Light Extend Recorder: Troubleshooting
Troubleshooting
Self-Test Mode
A self-test can be done on the following functions.
1. Self-test I (pacemaker detection check mode)
Provide a pacemaker signal to the recorder with an ECG simulator.
To enter the pacemaker detection mode, set the batteries while

pressing the STOP button.
Confirm the audible sound synchronizes with the pacemaker

signal input through the patient input connector.
Remove the batteries to end the self-test.
2. Self-test II (accelerometer sensor check mode)
After setting the batteries, press the STOP button three times
within a second.
Confirm the audible sound synchronizes as the recorder is moved

around.
Remove the batteries to end the self-test.

2019818-008
No Buzzer Sound After Installing the Batteries

No buzzer sound after
installing the batteries.
Are the batteries No

installed properly?
Yes Install the batteries

properly.

new?
Yes Replace with new

batteries.
Were the batteries

reinstalled over 10 No
seconds after the
batteries were
removed?
Reinstall the batteries
Yes over 10 seconds after
removing them.
Are the battery

electrodes clean and No
properly soldered?
Yes Call GE service.
Call GE service.

2019818-008
Beep Sound Will Not Stop After Installing the Batteries
Beep sound will not stop

after installing the batteries.
Are the batteries new? No

alkaline batteries.
Are the alkaline

batteries No
installed?
Yes Set new alkaline

batteries.
Call GE service.

2019818-008
ECG Cannot Be Previewed with Controller (I.R.)

ECG cannot be previewed
with the controller (I.R.).
Is the distance from

the controller within No
4.9 ft. (1.5 m)?
Yes
Position the controller
within 4.9 ft (1.5 m).
Is the I.R.
window facing the No
controller properly?
Reposition the I.R. window

Yes properly to the controller,
or remove any obstacle
between the recorder and
the controller.
Were the batteries No
set within one hour?
Yes Reset the batteries.
Has recording
Yes
already started?
No Preview ECG with the cable.

Cannot preview ECG by I.R.
operation if more than 3
minutes has elapsed since
Call GE service. recording started.

2019818-008
ECG Cannot be Previewed with Controller (Cable)

with the controller
(by the preview cable).
Is cable connection No
proper?
Yes Connect the

cable properly.
Is the cable Yes

damaged?
No Replace with a
new cable.
Call GE service.

2019818-008
ECG Cannot Be Previewed with SEER Light Connect Device

with the SEER Light
Connect Device.
Is the USB cable

from the Connect No
plugged in?
Yes Plug it in.
Is the orange LED No

on the Connect on?
Call GE Service.
Yes

No
the controller within
4.9 ft. (1.5 m)?

Yes within 4.9 ft (1.5 m).
Is the I.R.

Yes properly, or remove any
obstacle between the
recorder and the controller.

installed within one
hour?
Reinstall the batteries.
Yes
Has recording
Yes
already started?

No

2019818-008
Recording Cannot Start with the Controller (I.R.)
Recording cannot start

with the controller (I.R.).
Does the controller Yes

display “untransmitted
data?”
No Transfer previous data or

press the START button
when the controller displays
“Data still remains.”
Does
the controller display Yes
“Already started?”
No Reset the batteries over 30

seconds after removing them.
Is the distance
from the controller No
within 4.9 ft
(1.5 m?)
Adjust the position

Yes
within 4.9 ft. (1.5 m)
from the controller.
Does the I.R. window No

face the controller
properly?
Yes Reposition the I.R. windows

to face each other properly.
Remove any obstacles
Call GE Service. the controller.

2019818-008
Recording Cannot Start with the SEER Light Connect Device

with the Connect.
Is the USB cable

from the Connect No
plugged in?
Yes Plug it in.

on the Connect on?
Call GE Service.
Yes

data?”
Transfer previous data or
No press the START button.
Does
No Reinstall the batteries over 30

Is the distance
from the Connect No
within 4.9 ft
(1.5 m?)
Adjust the position
Yes from the Connect.

face the Connect
properly?
Reposition the I.R. windows
Yes to face each other properly.
Call GE Service. the Connect.

2019818-008
Cannot Start by Pressing the Start Button
Cannot start by pressing

the START button.
Was
the START button
pressed over 1.5 No
seconds?
Yes Press the START button

longer than 1.5 seconds.
Is it within
one hour of setting the No
batteries?
Yes
Reset the batteries.
Call GE Service

2019818-008
Cannot Record for 24 Hours
Cannot record for

24 hours.
Are there many

artifacts in the ECG Yes
recording?
No Refer to flow chart on

artifact later in this chapter.
Were the batteries

removed before recording Yes
for 24 hours?
Don’t remove the batteries

No
before recording for 24 hours.
Were alkaline No
batteries used?
Yes Use alkaline

batteries.
Are the
battery electrodes dirty Yes
or improperly
soldered?
No Clean the battery electrodes

or improve soldering.
Call GE Service.

2019818-008
Cannot Record for 48 Hours

Cannot record for
48 hours.
Is the recorder
labeled “SEER Light No
Extend?”
The recorder does not have

Yes
48-hour recording
capability.
Are there many

artifacts in the ECG Yes
recording?
No Refer to flow chart on

artifact later in this chapter.
Were the batteries

removed before recording Yes
for 48 hours?
Don’t remove the batteries

No
before recording for 48 hours.
Were alkaline No
batteries used?
Yes Use alkaline

batteries.
Are the
battery electrodes dirty Yes
or improperly
soldered?
No Clean the battery electrodes

Call GE Service.

2019818-008
Cannot Transfer Data from the Controller

Cannot transfer data
from the controller.
Is the transfer
cable properly connected? No
Yes Connect the

cable properly.
Does the
controller display “No data Yes
in the recorder?”
No No data in the recorder.

Record ECG again.
Does the
controller display Yes
“Recorder contains data
error?”
No Call GE Service.
Is the data output No

connector clean?
Yes Clean the data output

connector.
Is the transfer Yes

cable damaged?
No
Call GE Service.
Call GE Service.

2019818-008
Cannot Transfer Data from the Recorder to the SEER Light Connect Device
Cannot transfer data to
the Connect.
Is the USB cable

from the Connect No
plugged in?
Plug it in.
Yes
Is the orange LED

on the Connect on? No
Yes Is the green LED on No

the Connect on?
Attach the Connect to the Call GE Service.

recorder. Yes
Is the transfer
cable properly No
connected?
Connect the
Yes cable properly.
Does the
in the recorder?”
No data in the recorder.
No Record ECG again.

connector clean?
Clean the data output
Yes connector.
Is the transfer Yes

cable damaged?
Call GE Service.
No
Call GE Service.

2019818-008
Record Start Date/Time is Initialized
Record start date/time

is initialized.
Was the recording

started by pressing the No
START button?
Yes Call GE Service.
Were the batteries

Yes
removed during or after
recording?
Record start date/time will be
No initialized if the batteries are
removed before transferring the
ECG data after the START button
is pressed to start recording.
Did more than
one week pass from the Yes
last recording?
No Replace the batteries.
Call GE Service.

2019818-008
Artifact on ECG Recording
Artifact on ECG
recording.
Are electrodes
connected properly on No
the patient?
Yes Attach electrodes properly.
Is the patient cable No

connected properly?
Yes Connect the patient cable

properly.
Is the patient
cable connector No
clean?
Yes Clean the patient

cable connector.
Is the patient cable Yes

damaged?
No Call GE Service.
Call GE Service.

2019818-008
Cannot Detect Pacemaker Pulse
Cannot detect
pacemaker pulse.
Insert the batteries while

pressing the STOP button.
Disconnect the patient cable
and touch the electrode
connector with a finger.
Does audible beep Yes

sound?
No Normal pacemaker detection circuit.

Confirm pacemaker pulse detection
by the Preview function of the
Call GE Medical Systems controller. Reposition the CH1 if the
Information Technologies pulse signals are too small.
Service.

2019818-008
3 SEER Light/SEER Light
Extend Controller

2019818-008
For your notes

2019818-008
SEER Light/SEER Light Extend Controller: Component Names and Locations
Structure
Below are the names of each part on the SEER Light/SEER Light Extend
Controller.
A B
1.2 in.
(30 mm)
3.5 in. (90 mm)
C
D
G
7.9 in. (200 mm)
037A
Table 4. Controller Parts List

A Used to connect to the SEER Light recorder to check recording conditions.
input connector
NOTE This feature is reserved for future use.
B infrared terminal Used to communicate with the SEER Light recorder.

Transfer the instructions to a SEER Light recorder before recording.
Receive ECG waveform recording data from a SEER Light recorder to preview.

2019818-008
SEER Light/SEER Light Extend Controller: Component Names and Locations
Table 4. Controller Parts List (Continued)
C data transfer cable Used to transfer data from the SEER Light recorder. When not in use, store the cable in
the guide on the backside panel.
D Used to turn the power on and off.

power button
E Holter card slot Used to insert a Holter card.
F LCD (liquid crystal display) Displays operating conditions.
G F1 button Used to enter the preview mode (wired or wireless) to confirm the quality of ECG
recording.
H F2 button Used to enter the data transfer mode to transmit data to a Holter card.
I F3 button Used to start recording of the SEER Light recorder and to start transferring data to a
Holter card.
J set-up button (

)
Used to select settings.
K patient information entry Enter the patient’s alphanumeric information.

buttons
L battery cover In direction indicated, slide the cover open and place four new alkaline AAA type batteries
in the battery box.

2019818-008
SEER Light/SEER Light Extend Controller: Troubleshooting
Troubleshooting
Software Version
The software version of the SEER Light/SEER Light Extend Controller
appears in the lower right hand corner of the display upon start up.
Self-Test
A self-test can be done on the following functions.
1. Button check mode:
Enter the Set-up Condition display mode by pressing the POWER

button and button simultaneously. Continue to hold the button
while releasing the POWER button.
Press the CLEAR button at the Set-up Condition display mode.
Press the number 0 at the Factory Settings display mode.
The name of the button that was pressed will be displayed, and
an audible sound will be heard when the respective button is
pressed once.
NOTE
If the ENTER button is pressed three times the unit will
enter into the LCD check mode.
Turn off the power to end this function test.
2. LCD check mode:
Enter the Set-up Condition display mode by pressing the POWER

button and button simultaneously. Continue to hold the button
while releasing the POWER button.
Press the CLEAR button at the Set-up Condition display mode.
Press the number 0 at the Factory Settings display mode.

In the button check mode display press the ENTER button three
times, and the LCD display will appear darkened.
Press the POWER button to end this function test.

2019818-008
No Operation After Inserting Batteries and Pressing Power Button

No operation after inserting
batteries and pressing the
POWER button.

set properly?
Yes Set the batteries

properly.
Do the
batteries have sufficient No
power of >4.5 V?

batteries.
Did the
beep sound when the Yes
POWER button was
pressed?
Call GE service.
No
Call GE service.

2019818-008
ECG Cannot be Previewed with the Controller (I.R.)

with the controller (I.R.)
Communication Error

the recorder within
No
4.9 ft. (1.5 m)?
Yes Position the recorder

within 4.9 ft. (1.5 m).
Is the I.R.
recorder properly?

Yes properly to the recorder,
or remove any obstacle
the controller.
Has recording
Yes
already started?
No Preview ECG with the cable.

operation over 3 minutes after

2019818-008
ECG Cannot be Previewed by the Controller (Cable)

by the controller
(by the preview cable).
Is cable connection No
proper?
Yes Connect the

cable properly.
Is the cable Yes

damaged?
No Call GE service.
Call GE service.

2019818-008
Cannot Start Recording (I.R.)

Cannot start recording
(I.R.).
Does
No Reset the batteries over 30


the recorder within No
4.9 ft. (1.5 m)?
Yes Adjust the position within

4.9 ft. (1.5 m) from the
recorder.

face the controller
properly?
to face each other properly.
Yes Remove any obstacles
the controller.
Has
over 60 minutes
Yes
passed since recording
started?
No If over 60 minutes have

passed, the SEER Light
cannot start by I.R.
operation.
Call GE service.

2019818-008
Pressing the Appropriate Key(s) Does Not Start Operation
Pressing the appropriate

key(s) does not start operation.
Can
the operation panel No
key(s) be pressed
properly?
Call GE service.
Yes
Is there
debris between PC Yes
board and key sheet
panel?
No Call GE service.
Call GE service.

2019818-008
Beep Sounds While the Flash Card is Inserted
Beep sounds while the

flash card is inserted.
The display is distorted.
Is the flash card

inserted completely? No
Yes Insert the card

completely.
Is the
card inserted in the Yes
opposite direction?
No Insert the card

properly.
Call GE service.

2019818-008
Data Cannot be Transferred from the Recorder

Data cannot be transferred
from the recorder.

connector clean?
Yes Clean the

connector.
Is the connector Yes

damaged?
No Replace the
connector.
Has
the compact flash card No
been formatted?
Yes Format the compact

flash card.
Is the card defective? Yes
No Replace with a
new card.
Does data remain on Yes

the card?
No Transfer the
data to the PC.
Are
there distorted card Yes
connector pins?
No Call GE service.
Call GE service.

2019818-008
Recording Start Date/Time is Not Correct

Recording start date/time
is not correct.
Is date within
No
one month?
Yes
Adjust date.
See next flowchart.
Time is Not Correct

Time is not correct.
Is it within 5 years No
of use?
Yes Call GE service.
Are the
battery electrodes No
clean or properly
solder?
Yes Clean the electrodes

Replace the PC boards.

2019818-008
SEER Light/SEER Light Extend Controller: Inspection
Inspection
Production process inspection sheet and inspection procedure.
M. No.
Product Model Name SEER Light Controller Date (Start Inspection) Approval Audit
Serial No. Board No.
Production Lot No.
Program Version Production Specification
High temperature heat run (40 to 48 hours) Start and End Date
Inspection Before Heat-Run Staff
No. Item Inspection Procedures Result Accept Reject
1 Appearance Check paint condition, no scratches or stains on LCD and cases, clear wording,
etc. Check connector pin of memory card for breaks, bends, etc.
2 Power switch Turn ON the power switch. Ensure there are buzzer sounds and the factory reset
menu appears on the LCD. Confirm program version number.
3 Set the time Set year, month, date, and time. Turn off the Auto Power function for heat-run
inspection.
4 Key/LCD check Under the inspection mode, ensure the key input and LCD display are normal,
LCD backlight is lit, and the keys should not stick when pressed.
5 Leakage current Patient leakage current is less than 10 µ A. µA
6 Power ON Insert the batteries and confirm buzzer one time. Press start switch, confirm to buzzer and
blink red LED. Then press stop switch and check buzzer sound and LED blinking are
stopped.
7 Start test Ensure that the SEER Light is starting (straight line: 1.5 m).
8 IrDA preview Use SEER Light, which is pre-installed with ECG wave, and ensure that the
check displayed waveform of 1 ch, 2 ch, and 3 ch are normal under the preview function.
9 Preview check Use SEER Light, which is pre-installed with ECG wave, and ensure that the
with cable displayed analog waveform of 1 ch, 2 ch, and 3 ch are normal.
10 Analog output Using inspection controller with cable, confirm analog waveforms 1 ch, 2 ch, and 3 ch are
normal.
11 Transfer test Connect the SEER Light. Ensure that data is transferred and that the data can be
installed onto the Holter card.
12 Check settings Check the year, month, date, and time (with ±1 minute).
13 Reset menu Used to initialize the settings (menu).
14 Auto Power Off Turn ON the power switch. Check that the power is automatically switched off if no
function operation for 15 minutes continuously.
15 Appearance Check painting conditions such as no scratches stains on LCD cases, clear wording,
Ver. No.
etc. Check serial plate and battery mark seal (version number) is securely affixed.
16 Supply current Start at 6 V. The supply current is 60 ±6 mA. mA
No. Visual Inspection Accept Reject No. Visual Inspection Accept Reject
1 Battery mark 1 place 4 Electrode welding 2 places
2 Ribbon 1 place 5 LCD boards, connector cutting 1 place
3 Board installation 1 place 6 Main body assembly 4 places
Notes:

2019818-008
4 SEER Light Connect
Revision A SEER Light Ambulatory Recorder/Controller 4-1

2019818-008
For your notes
4-2 SEER Light Ambulatory Recorder/Controller Revision A

2019818-008
SEER Light Connect: Component Names and Locations
The SEER Light Connect is shown and described below. It is used as a

direct interface connection between the recorder and the Holter analysis
system. This device is also referred to as “the connect” in this document.
Structure
Below are the names of each part on the SEER Light Connect.
084A
Name Function
A data transfer cable Used to transfer data from the SEER Light recorder
to the SEER Light Connect.
B infrared terminal Used to communicate with the SEER Light

recorder.
Receives ECG waveform data from a SEER

Light recorder to preview.
Transfers patient demographics to the SEER
Light recorder.
Starts the SEER Light recorder.
C USB Connection Uses a USB patch cord to transfer data from the
SEER Light Connect to the Holter analysis system.
D LED indicator Flashes when data is transferring.

Lights without flashing when a proper connection
exists.

2019818-008
SEER Light Connect: Troubleshooting
Troubleshooting
WARNING
LEAKAGE CURRENT—Electrical shock to patient could

result from component failure and lack of power
isolation.
In the event this system is used in the patient vicinity, it

must be configured in such a way that it and all of its
electrically-connected peripheral devices are isolated from
mains power to prevent excessive leakage current to the
patient. This can be accomplished through the use of
isolated mains power, or a medical grade isolation
transformer (in compliance with UL 60601, CAN/CSA
C22.2 No. 601.1, IEC 60601-1) with this system. All non-
medical peripheral devices shall comply with IEC and ISO
safety standards that are relevant to that equipment (i.e.,
IEC 60950, UL 60950).
Use of the SEER Light Connect device in the patient

vicinity requires that these measures are observed.
Software Version
To view the software version of the SEER Light Connect device, click
About in the SEER Light Hookup window.

2019818-008
ECG Cannot Be Previewed with SEER Light Connect Device

with the SEER Light
Connect Device.
Is the USB cable

from the Connect No
plugged in?
Yes Plug it in.

on the Connect on?
Call GE Service.
Yes

No
the controller within
4.9 ft. (1.5 m)?

Yes within 4.9 ft (1.5 m).
Is the I.R.

Yes properly, or remove any
obstacle between the
recorder and the controller.

installed within one
hour?
Reinstall the batteries.
Yes
Has recording
Yes
already started?

No

2019818-008
Recording Cannot Start with the SEER Light Connect Device

with the Connect.
Is the USB cable

from the Connect No
plugged in?
Yes Plug it in.

on the Connect on?
Call GE Service.
Yes

data?”
Transfer previous data or
No press the START button.
Does
No Reinstall the batteries over 30

Is the distance
from the Connect No
within 4.9 ft
(1.5 m?)
Adjust the position
Yes from the Connect.

face the Connect
properly?
Yes to face each other properly.
Call GE Service. the Connect.

2019818-008
Cannot Transfer Data from the Recorder to the SEER Light Connect Device
Cannot transfer data to
the Connect.
Is the USB cable

from the Connect No
plugged in?
Plug it in.
Yes
Is the orange LED

on the Connect on? No
Yes Is the green LED on No

the Connect on?
Attach the Connect to the Call GE Service.

recorder. Yes
Is the transfer
cable properly No
connected?
Connect the
Yes cable properly.
Does the
in the recorder?”
No data in the recorder.
No Record ECG again.

connector clean?
Clean the data output
Yes connector.
Is the transfer Yes

cable damaged?
Call GE Service.
No
Call GE Service.

2019818-008
Recording Start Date/Time is Not Correct

Recording start date/time
is not correct.
Is date correct on
No
the PC?
Yes
Adjust date/time on the PC.
Call GE Service.

2019818-008
5 Maintenance

2019818-008
For your notes

2019818-008
Maintenance: Maintenance
Maintenance
Visual Inspection
Perform a visual inspection daily. If you notice any items that need
repair, contact an authorized GE Medical Systems Information
Technologies service person to make the repairs.
Check the case and display screen for cracks or other damage.
Regularly inspect all cords and cables for fraying or other damage.
Inspect all plugs, cables, and connectors for bent prongs or pins.
Verify that all cords and connectors are securely seated.
Inspect controls for proper operation.
Inspect the LCD to make sure all the segments function.
Precautions
Do not immerse any part of the equipment in water.
Do not use organic solvents, ammonia based solutions, or abrasive

cleaning agents which may damage equipment surfaces.
NOTE
Remove the batteries before cleaning
Cleaning
Clean the exterior surfaces with a clean, soft cloth and a mild
dishwashing detergent diluted in water.
Wring the excess water from the cloth. Avoid contact with open
vents, plugs, or connectors.
Do not spray or spill fluid directly on the recorder/controller.

Dry the surfaces with a clean cloth or paper towel.
Cleaning Frequency
With each new patient use, clean the SEER Light Recorder/Controller
and the SEER Light recorder pouch, leadwires, and patient cable.

2019818-008
Maintenance: Storing the Recorder
Storing the Recorder
When the SEER Light Recorder/Controller will not be in use for a period
of time:
Remove the batteries
Disconnect and properly store any patient cables.
Memory card may remain in the recorder.

2019818-008
Maintenance: Maintenance/Repair Log
Maintenance/Repair Log
Unit Serial Number:
Institution Name:
Date Maintenance/Repair Technician

2019818-008
Maintenance: Maintenance/Repair Log
Maintenance/Repair Log
Unit Serial Number:
Institution Name:
Date Maintenance/Repair Technician

2019818-008
Appendix A —
Technical Specifications
Revision B SEER Light Ambulatory Recorder/Controller A-1

2019818-008
For your notes
A-2 SEER Light Ambulatory Recorder/Controller Revision B

2019818-008
Appendix A: Technical Specifications
Technical Specifications
SEER Light/SEER Light Extend Ambulatory Recorder

The following table lists the specifications for the SEER Light/
SEERLight Extend Ambulatory Recorder.
Description Specification
Dimensions Height: 54 mm (2.1 in)
Width: 85 mm (3.35 in)
Depth: 15 mm (0.6 in)
Weight 72 g (2.5 oz) including batteries
Operating temperature 0 to 45°C (32 to 113°F)
Operating humidity 10 to 95% relative humidity (no condensation
allowed)
Storage temperature –20 to 65°C (-4 to 149°F)
Storage humidity 5 to 90% relative humidity (no condensation
allowed)
Material Aluminum ABSPC (main body)
Recording time within 24 hours — SEER Light
within 48 hours — SEER Light Extend
Recording method Digital memory
Power supply 2 x AAA Alkaline battery
Recording channel ECG: 3 channels
Movement level: 1 channel
Pacemaker pulse: 1 channel
Pacemaker detection channel CH1
Memory 32 Mbyte
Input level 16 mV p-p
A/D converter 10 bit, 8 ms sampling
Frequency response 0.05 to 40 Hz
Safety Type B
Input impedance Over 10 M Ohms
Time data backup Within 1 week (when started by the Cardy 301
recorder)

2019818-008
SEER Light Ambulatory Controller

The following table lists the specifications for the SEER Light
Ambulatory Controller.
Dimensions Height: 200 mm (7.9 in)
Weight 285 g (9.9 oz) including batteries
allowed)
allowed)
Power supply 4 x AAA Alkaline battery
Vibration endurance Operation: 0.5 G (10 to 20 Hz)
Non operation: 3.0 G (100 to 300 Hz)
Data transfer medium Compact flash card
Time accuracy + 60 seconds per month

2019818-008
SEER Light Connect Device

The following table lists the specifications for the SEER Light Connect
device.
Dimensions Height: 13 mm (.51 in)
Cable length: 260 mm (10.24 in)
Weight 87 g (.19 lbs)
allowed)
allowed)
Power supply DC 5V
Recorders SEER Light Recorder
SEER Light Extend Recorder

2019818-008
For your notes

2019818-008
Appendix B —
Electromagnetic
Compatibility
Revision B SEER Light Ambulatory Recorder/Controller B-1

2019818-008
For your notes
B-2 SEER Light Ambulatory Recorder/Controller Revision B

2019818-008
Electromagnetic Compatibility: Electromagnetic Compatibility (EMC)
Electromagnetic Compatibility (EMC)
Changes or modification to this system not expressly approved by GE

Medical System could cause EMC issues with this or other equipment.
This system is designed and tested to comply with applicable regulation
regarding EMC and needs to be installed and put into service according
to the EMC information stated as follows.
WARNING
Use of portable phones or other radio frequency (RF)
emitting equipment near the system may cause
unexpected or adverse operation.
WARNING
The equipment or system should not be used adjacent to,
or stacked with, other equipment. If adjacent or stacked
use is necessary, the equipment or system should be
tested to verify normal operation in the configuration in
which it is being used.
Guidance and Manufacturer’s Declaration – Electromagnetic

Emissions
The SEER Light recorder and controller are intended for use in the
electromagnetic environment specified below. It is the responsibility of
the customer or user to ensure that the SEER Light recorder and
controller are used in such an environment.
Emissions Test Compliance Electromagnetic Environment - Guidance
The equipment uses RF energy only for its
RF emissions internal function. Therefore, its RF emissions
Group 1
CISPR11 are very low and are not likely to cause any
interference in nearby electronic equipment.
RF emissions
Class A
CISPR11 The equipment is suitable for use in all
establishments including domestic
Harmonic Emissions
Class A establishments and those directly connected to
EN 61000-3-2
the public low-voltage power supply network
Voltage fluctuations/ that supplies buildings used for domestic
Flicker emissions Complies purposes.
EN 61000-3-3

2019818-008

Immunity
the customer or user to ensure that the SEER Light recorder and
Electromagnetic Environment -
Immunity Test EN 60601 Test Level Compliance Level
Guidance
Electrostatic ± 6 kV contact ± 6 kV contact Floors should be wood, concrete or

discharge (ESD) ± 8 kV air ± 8 kV air ceramic tile. If floors are covered with
EN 61000-4-2 synthetic material, the relative humidity
should be at least 30%.
Electrical fast ± 2 kV for power supply lines ± 2 kV for power supply lines Not applicable. The SEER Light recorder
transient/burst ±1 kV for input/output lines ±1 kV for input/output lines and controller are not powered by Mains
EN 61000-4-4 power.
Surge ± 1 kV differential mode ± 1 kV differential mode Not applicable. The SEER Light recorder
EN 61000-4-5 ± 2 kV common mode ± 2 kV common mode and controller are not powered by Mains
power.
Voltage dips, short <5% Ut (>95% dip in Ut) <5% Ut (>95% dip in Ut) Not applicable. The SEER Light recorder
interruptions and for 0.5 cycles for 0.5 cycles and controller are not powered by Mains
voltage variations on 40% Ut (60% dip in Ut) 40% Ut (60% dip in Ut) power.
power supply input for 5 cycles for 5 cycles
lines 70% Ut (30% dip in Ut) 70% Ut (30% dip in Ut)
EN 61000-4-11
for 25 cycles for 25 cycles
<5% Ut (>95% dip in Ut) <5% Ut (>95% dip in Ut)
for 5 sec for 5 sec
Power frequency 3 A/m 3 A/m Power frequency magnetic fields should be
(50/60 Hz) magnetic at levels characteristics of a typical location
field in a typical commercial or hospital
EN 61000-4-8 environment.
NOTE
Ut is the AC mains voltage prior to application of the test level.

2019818-008

Immunity
the customer or user to assure that the SEER Light recorder and
Immunity Test EN 60601 Test Level Compliance Level Electromagnetic Environment – Guidance
Portable and mobile RF communications equipment should not

be used closer to any part of the equipment, including cables,
than the recommended separation distance calculated from the
equation applicable to the frequency of the transmitter.
Recommended separation distance
Conducted RF 3 Vrms 3 V rms

EN 61000-4-6 150 KHz to 80 MHz d = 1.2 P
Radiated RF 3 V/m 3 V/m

EN 61000-4-3 80 MHz to 2.5 GHz d = 1.2 P 80 MHz to 800 MHz
d = 2.3 P 800 MHz to 2.5 GHz
where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer, and d is
the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by an

electromagnetic site surveya, should be less than the
compliance level in each frequency rangeb.
Interference may occur in the vicinity of equipment marked with
the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by reflection from structures, objects,
and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radio, AM
and FM radio broadcast, and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength
in the location in which the equipment is used exceeds the applicable RF compliance level above, the equipment should be
observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as
re-orienting or relocating the equipment.
b
Over the frequency range 150 KHz to 80 MHz, field strengths should be less than 3 V/m.

2019818-008
Recommended Separation Distances

The table below provides the recommended separation distances (in
meters) between portable and mobile RF communication equipment and
the SEER Light recorder and controller.
electromagnetic environment on which radiated RF disturbances are
controlled. The customer or the user of the SEER Light recorder and
controller are can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the SEER Light recorder
and controller as recommended below, according to the maximum output
power of the communications equipment.
Separation Distance in Meters (m) According to Frequency of Transmitter
Rated Maximum Output 150 kHz to 80 MHz 150 kHz to 80 MHz

80 MHz to 800 MHz 800 MHz to 2.5 GHz
Power of Transmitter in outside ISM bands in ISM bands
Watts d = 1.2 P d = 2.3 P
d = 1.2 P d = 1.2 P
0.01 0.12 0.12 0.12 0.23
0.1 0.38 0.38 0.38 0.73
1 1.2 1.2 1.2 2.3
10 3.8 3.8 3.8 7.3
100 12 12 12 23
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
For transmitters rated at a maximum output power not listed above, the
recommended separation distance [d] in meters (m) can estimated using
the equation applicable to the frequency of the transmitter, where P is
the maximum output power rating of the transmitter in watts (w)
according to the transmitter manufacturer.
NOTE
These guidelines may not apply in all situations. Electromagnetic

propagation is affected by absorption and reflection from structures,
objects, and people.

2019818-008
Compliant Cables and Accessories
WARNING
The use of accessories, transducers and cables other than
those specified may result in increased emissions or
decreased immunity performance of the equipment or
system.
The table below lists cables, transducers, and other applicable

accessories with which GE Medical Systems claims EMC compliance.
NOTE
Any supplied accessories that do not affect EMC compliance are not
included.
Part No Description Maximum Lengths
2008750-002 SEER Light 64MB Compact Flash NA
2008751-001 Compact Flash to PC Adapter NA
2008594-00X SEER Light Patient Cable 1m
3801-005 Battery Alkaline 1.5V AAA NA

2019818-008
For your notes

2019818-008
Index
Revision B SEER Light Ambulatory Recorder/Controller Index-1

2019818-008
Index-2 SEER Light Ambulatory Recorder/Controller Revision B
2019818-008
A Input connector 12, 3
abrasive cleaning agents 3 Intended use 6
Access LED 3
L
Accessories 10
LCD 4
Accidental spills warning 6
Leakage current warning 7, 4
Alphanumeric
keypad 4 M
Authorized service 10 Maintenance 5, 3
manual
B
definitions 3
Battery box
purpose 3
controller
revision history 3
cover 4
manuals
recorder
related 5
cover 3
Modifications caution 8
C
N
Cables warning 6
Note definition 6
Cardiac application warning 6
Caution definition 6 O
certification Output connector 12, 3
CSA 22.2 No. 601 11
P
EN 60950 (UL 950) 11
Pacemaker
IEC 601-1 11
warning 7
UL 2601-1 11
Patient cable
Cleaning 3
connector 4
cleaning
Polarity of batteries 12
what to use 3
Power 12
Conductivity warning 6
button on controller 4
D Precautions 3
Danger definition 6
R
DATA LED 3
REC LED 3
Data transfer
data transfer cable 4 S
Defibrillation warning 6 Safety Information 6
Definition Serial Number 8
danger, warning, caution, note 6 Serial number 8
Disposal 9 Set-up button 4
caution 7 Start/event button 3
Stop 12
E
Stop button
Electrosurgery warning 7
recorder 4
Equipment Symbols 12
Storing
Equipment symbols 9
recorder 4
Event 12
Supervised use warning 7
F Symbols on equipment 9
Function buttons (F1, F2, F3) 4
V
H visual inspection 3
Holter card slot 4
W
I Warning definition 6
IEC 10
immersion in water 3
information technology equipment 11
Infrared terminal 3
Revision B SEER Light Ambulatory Recorder/Controller Index-3

2019818-008
Index
Index-4 SEER Light Ambulatory Recorder/Controller Revision B

2019818-008

Seer Light Ambulatory Recorder/Controller: Service Manual

Uploaded by

Copyright:

Available Formats

Seer Light Ambulatory Recorder/Controller: Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Seer Light Ambulatory Recorder/Controller: Service Manual

Uploaded by

Copyright:

Available Formats

SEER® Light

Service Instructions for:

SEER Light/SEER Light Extend Compact Digital Holter Recorder

SEER Light/SEER Light Extend Controller

SEER Light Connect

© 2005 General Electric Company. All rights reserved.

T-2 SEER Light Ambulatory Recorder/Controller Revision B

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Responsibility of the Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Equipment Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

2 SEER Light/SEER Light Extend Recorder . . . . . . . . . . . 2-1

Revision B SEER Light Ambulatory Recorder/Controller i

3 SEER Light/SEER Light Extend Controller . . . . . . . . . . . 3-1

4 SEER Light Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

ii SEER Light Ambulatory Recorder/Controller Revision B

Storing the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Maintenance/Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Maintenance/Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .A-1

Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . .B-1

Revision B SEER Light Ambulatory Recorder/Controller iii

Revision B SEER Light Ambulatory Recorder/Controller 1-1

1-2 SEER Light Ambulatory Recorder/Controller Revision B

The revision history of this document is summarized in the table below.

Table 1. Revision History 2019818-008

Revision Date Comment

A 15 May 2005 Initial release of manual.

B 15 July 2005 Manual updated for clarity.

 Items shown in Italicized text are software terms which identify

 To perform an operation which appears with a plus (+)sign between

Revision B SEER Light Ambulatory Recorder/Controller 1-3

 Enter means to press the “Enter” or “Return” key on the keyboard.

1-4 SEER Light Ambulatory Recorder/Controller Revision B

See the documents listed below for additional information.

Table 2. SEER Light Documents

Part Number Name

Revision B SEER Light Ambulatory Recorder/Controller 1-5

Hazard is defined as a source of potential injury to a person.

DANGER indicates an imminent hazard which, if not avoided, will

WARNING indicates a potential hazard or unsafe practice which, if not

CAUTION indicates a potential hazard or unsafe practice which, if not

NOTE provides application tips or other useful information.

ACCIDENTAL SPILLS — If liquids have entered a

CABLES — To avoid possible strangulation, route all

CARDIAC APPLICATION — This device cannot be used

CONDUCTIVITY — Keep the conductive parts of lead

DEFIBRILLATOR PRECAUTIONS — Do not come into

1-6 SEER Light Ambulatory Recorder/Controller Revision B

contact with patients during defibrillation. Otherwise,

ELECTROSURGERY — If an electrosurgery device is

LEAKAGE CURRENT — Electrical shock to patient

In the event this system is used in the patient vicinity, it

Use of the SEER Light Connect device in the patient

PACEMAKER PATIENTS — Take precautions to avoid

SUPERVISED USE — This device is intended for use

RESTRICTED SALE — U.S. federal law restricts this

BEFORE OPERATION — Check that the instrument

DISPOSAL — At the end of its service life, the product

Items shown in Italicized text are software terms which identify

To perform an operation which appears with a plus (+)sign between

Enter means to press the “Enter” or “Return” key on the keyboard.

Use a piece of damp cloth with alcohol to clean the

The device cannot be sterilized.

Do not use xylene and petrol related liquid for

To ensure proper operation of the device, it is

Check the patient cable and connectors every month

Install and keep device away from splashing water.

Do not install the device where it may be affected by

Prevent the device from tilting, and protect it from

Do not install the device in a chemical storage area or

Assembly operations, extensions, readjustments, modifications, or

The equipment is used in accordance with the instructions for use.

use of the accessory in the PATIENT VICINITY; and

evidence that the safety certification of the ACCESSORY has been

B Use to start recording.

Provide a pacemaker signal to the recorder with an ECG simulator.

To enter the pacemaker detection mode, set the batteries while

Confirm the audible sound synchronizes with the pacemaker

Remove the batteries to end the self-test.

Confirm the audible sound synchronizes as the recorder is moved

Remove the batteries to end the self-test.