2511 PREPREG SYSTEM

This semi-toughened epoxy prepreg system was specifically

formulated for better oven cure processing than the #2510
general aviation (AGATE) prepreg system. #2511 provides
excellent all-around structural properties with a high wet
and dry TG while offering a flexible cure temperature (250°F
to 350°F, 121°C to 177°C) with a very low void content. This
prepreg system also can be used in industrial and recreational
applications.

Industry Material Specification Industry Database

Coming soon. Coming soon.

Easy Layup
High Heat Tolerance Product allows complex part layup
High Tg is suitable for structures with minimal cuts or ridge lines. It
exposed to elevated service tem- maintains a comparable class A finish
peratures. through post-cure, minimizing sand-
ing and finishing times.

Flexible Cure Methods

Readily Available Curing methods include autoclave
Product is in stock and ready to ship. or oven cure. Product can be cured
with or without using a dwell.

www.toraycma.com
2511 253-846-1777
2511 Prepreg System Rev. 6: Updated February 27, 2018
 2511

AVAILABLE PRODUCT FORMATS

PART NUMBER FIBER FORMAT FIBER TYPE/STYLE FAW (GSM) RC % WEIGHT ROLL WIDTH (IN)
P711AG-15 Unidirectional T700G 150 35 39, 36, 24, 12, 6
F6273C-11M Plain Weave T700S-12K 190 42 38
FGF7781-11I Glass Fabric 7781 295 38 38

NEAT RESIN PHYSICAL PROPERTIES RESIN VISCOSITY CURVE

PROPERTY METHOD UNITS VALUE 100000

Density ASTM D595 g/cc 1.267

10000
Tg (Dry) DMA °F (°C) 309 (154)
Tg (Wet) DMA °F (°C) 262 (128)

VISCOSITY (P)
1000
Gel Time * Minutes 46
KIC ASTM D504 ksi*in0.5 0.75
100

* From room temperature to 248°F at 3.1°F/min.

10

1
40 50 60 70 80 90 100 110 120
TEMPERATURE (°C)

LAMINA/LAMINATE MECHANICAL PROPERTIES: P711AG-15

PROPERTY SYMBOL METHOD UNITS CTA RTA ETW
0° Tensile Strength F1t ASTM D3039 Ksi (MPa) 272 (1847) 321 (2212) 272 (1874)
0° Tensile Modulus E1t ASTM D3039 Msi (GPa) 17.8 (123) 17.6 (121) 17.8 (123)
0° Compressive Strength F1c SACMA SRM 1 Ksi (MPa) 235 (1619) 231 (1592) 166 (1144)
In-Plane Shear Strength @ 5% or Ultimate F12 ASTM D3518 Ksi (MPa) - 25.0 (172) -
Short Beam Shear Strength SBS ASTM D2344 Ksi (MPa) - 15.4 (106) -
Open Hole Compression Strength (25/50/25) OHC ASTM D6484 Ksi (MPa) - 42.8 (295) 34.2 (236)
Compression After Impact (25/50/25) CAI ASTM D7137 Ksi (MPa) - 26.2 (181) -
Fiber Volume Fraction Vf ASTM D3171 % - 54.7 -
Cured Ply Thickness CPT - Inches (mm) - 0.0058 (0.148) -

Tension and compression values are normalized to the indicated Vf herein.

Notes:
CTA: -67°F (-55°C), Ambient
RTA: 72°F (22°C), Ambient
ETW: 180°F (82°C) Ambient, Conditioned at 160°F (71°C) /85% RH until equilibrium

Please refer to SDS for handling and disposal.

For more information or purchasing inquiries:

sales@toraycma.com | www.toraycma.com | 253-846-1777

The data listed herein are lot averages and for reference purposes only. The results are not intended for specification purposes. These commodities, technology or software were exported from
the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
2511 Prepreg System Rev. 6: Updated February 27, 2018
 2511

LAMINA/LAMINATE MECHANICAL PROPERTIES: F6273C-11M

PROPERTY SYMBOL METHOD UNITS CTA RTA ETW
0° Tensile Strength F1t ASTM D3039 Ksi (MPa) 145 158 158
90° Tensile Strength F2t ASTM D3039 Ksi (MPa) 144 147 133
0° Tensile Modulus E1t ASTM D3039 Msi (GPa) 8.49 8.57 9.11
90° Tensile Modulus E2t ASTM D3039 Msi (GPa) 8.22 8.43 8.76
0° Compressive Strength F1c ASTM D6641 Ksi (MPa) 106 97.7 74.5
90° Compressive Strength F2c SACMA SRM 1 Ksi (MPa) 104 85.6 65.5
0° Compressive Modulus E1c ASTM D6641 Msi (GPa) 7.15 7.53 8.40
90° Compressive Modulus E2c ASTM D6641 Msi (GPa) 7.22 7.04 8.18
In-Plane Shear Strength @ 5% or Ultimate F12 ASTM D3518 Ksi (MPa) 17.2 12.5 6.92
In-Plane Shear Modulus G12 ASTM D5379 Msi (GPa) 0.690 0.582 0.429
Short Beam Shear Strength SBS ASTM D2344 Ksi (MPa) 10.1 9.83 4.63
Poisson’s Ratio ν12 ASTM D3039 - 0.057 0.054 0.024
Poisson’s Ratio ν21 ASTM D3039 - 0.058 0.052 0.041
Open Hole Compression Strength (25/50/25) OHC ASTM D6484 Ksi (MPa) - 39.4 (271) 31.0 (214)
Compression After Impact (25/50/25) CAI ASTM D7137 Ksi (MPa) - 30.9 (213) -
Laminate Density ρ ASTM D792 g/cc 1.51
Fiber Volume Fraction Vf ASTM D3171 % 48.2
Cured Ply Thickness CPT - Inches (mm) - 0.0086 (0.218) -

Tension and compression values are normalized to the indicated Vf herein.

Notes:
CTA: -67°F (-55°C), Ambient
RTA: 72°F (22°C), Ambient
ETW: 180°F (82°C) Ambient, Conditioned at 160°F (71°C) /85% RH until equilibrium

Please refer to SDS for handling and disposal.

For more information or purchasing inquiries:

sales@toraycma.com | www.toraycma.com | 253-846-1777

The data listed herein are lot averages and for reference purposes only. The results are not intended for specification purposes. These commodities, technology or software were exported from
the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
2511 Prepreg System Rev. 6: Updated February 27, 2018
 2511

BAGGING PROCEDURE RECOMMENDED VACUUM CURE CYCLE (270°F OVEN CURE)

140 80

120 70

60

TEMPERATURE (°C)
100

VACUUM (kPa)
50
80
40
60
30
STORAGE LIFE 40
20
Temperature (°C)
Out Life 28 days @ 75 °F 20
Vacuum (kPa) 10
Freezer Life 24 months @ <10 °F
0 0
0 50 100 150 200 250 300 350
TIME (MINUTES)

Notes:
1. De-bulk every four plies, or as needed, when laying up material.
2. The vacuum should be checked for leaks before beginning the cure
cycle. The leak rate shall be less than 2.0 inches of Hg (7 kPa) over 5
minutes.
3. It is recommended that small test specimens have a pre-cure vacu-
um hold time of 1 hour, for medium sized panels (>1ft2) for 3 hours,
and for complex layups (ply drops, >2ft2) for 16+ hours.
4. The vacuum should be within 2” of Hg (7 kPa) for an absolute vacu-
um for a given altitude. For example, at sea level, the vacuum should
be at a minimum of 28” Hg (95 kPa).
5. Ramp to 190 ± 10°F at 1-5°F/min (88 ± 5°C at 0.6-2.8°C/min) and hold
for 90 minutes.
6. Ramp to 270 ± 10°F at 1-5°F/min (132 ± 5°C at 0.6-2.8°C/min) and
hold for 120 minutes.
7. Cool temperature down to 130°F at max rate of 5°F/min (54°C at
2.8°C/min).

Please refer to SDS for handling and disposal.

For more information or purchasing inquiries:

sales@toraycma.com | www.toraycma.com | 253-846-1777

The data listed herein are lot averages and for reference purposes only. The results are not intended for specification purposes. These commodities, technology or software were exported from
the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
2511 Prepreg System Rev. 6: Updated February 27, 2018