CS8000 K8000c Installation Guide Sm736 Ed02 en

KODAK 8000C Digital Panoramic and Cephalometric
Extraoral Imaging System
Installation Guide
Notice
Congratulations on your purchase of the KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging
System. Thank you for your confidence in our products and we will do all in our power to ensure your complete
satisfaction.
The Installation Guide for the KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System
includes information on the cephalometric features. For the panoramic features, see the KODAK 8000 Extraoral
Imaging System (SM721) Installation Guide. We recommend that you thoroughly familiarize yourself with this
Guide in order to make the most effective use of your system.
WARNING: We recommend that you consult the “Safety, Regulatory and the Technical
Specification User Guide” before using the KODAK 8000C Extraoral Imaging Systems.
The information contained in this Guide may be subject to modification without notice, justification or notification
to the persons concerned.
No part of this Guide may be reproduced without the express permission of Carestream Health, Inc.
The US Federal law restricts this device to sale by or on the order of a physician.
This document is originally written in English.
Manual Name: KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System Installation
Guide
Part Number: SM736
Revision Number: 02
Print Date: 03/2010
The brand names and logos reproduced in this Guide are copyright.
KODAK is a trademark of KODAK used under License.
KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System, complies with Directive
93/42/CEE relating to medical equipment.
.
0086
Manufacturer
Carestream Hea lth, Inc.
150 Verona Street
Rochester NY 14 608
Authorized Representative in the European Community

EC REP
TROPHY
4, Rue F. Pelloutier, Croissy-Beaubourg
77435 Marne la Vallée Cedex 2, France
Contents
1—About This Guide
Conventions in this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
2—KODAK 8000C UNIT OVERVIEW

General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Mobile Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
General Functional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Digital Sensor Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
Laser Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
X-Ray Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Positioning Accessories and Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
3—KODAK 8000C PACKAGING

Standard Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
4—SITE PREPARATION BEFORE INSTALLATION

Standard Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
X-Ray Room Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
Computer System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
5—INSTALLING THE CEPHALOSTAT

Tool Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Technical Staff Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Opening the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2
Installing the Cephalostat Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Installing the Cephalostat Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Installing the Cephalostat Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Wiring the Cephalostat Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Wiring the Cephalostat to the Unit Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
Post-Installation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
Adjusting the Cephalostat Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
Adjusting the Cephalostat Head Inclination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
Adjusting the Height of the Cephalostat Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12
Adjusting the Ear Cones Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
Adjusting the Nasion Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–15
Adjusting the Cephalometric Frankfurt Positioning Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–17
Checking the Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–18
Fitting the Covers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–20
KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System Installation Guide (SM736)_Ed 02 iii
Contents
Fitting the Cephalostat Covers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–22
6—Maintenance
Annual Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
iv
Chapter 1
About This Guide
Conventions in this Guide
The following special messages emphasize information or indicate potential risk to

personnel or equipment:
WARNING
Warns you to avoid injury to yourself or others by following the
safety instructions precisely.
CAUTION
Alerts you to a condition that might cause serious damage.
IMPORTANT
Alerts you to a condition that might cause problems.
NOTE
Emphasizes important information.
TIP
Provides extra information and hints.
KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System Installation Guide (SM736)_Ed 02 1–1
Conventions in this Guide
1–2 About This Guide

Chapter 2
KODAK 8000C UNIT OVERVIEW
The KODAK 8000C digital panoramic and cephalometric unit is designed to carry out the
following radiological examinations:
• Panoramic
• Maxillary Sinus
• Temporomandibular Joints (TMJ)
• Lateral cephalometric
• Frontal (PA or AP) cephalometric
• Oblique cephalometric
• Submento-vertex cephalometric
• Carpus cephalometric
General Overview
The KODAK 8000C digital panoramic and cephalometric unit is composed of the
following functional components:
• The unit head that contains all the electronic control

• The rotative arm
• The fixed arm with a control panel
• The panoramic digital sensor
• The x-ray source assembly
• The x-ray remote control
• The chin rest and bite block
• The chin rest base
• The panoramic chin rest and bite block
• The temple supports
• The hand grips
• The cephalostat arm
• The cephalostat head
• The head clamps and ear cones
• The nasion support
• The acquisition software (see “Imaging Software Overview”)
The following figures illustrate the general overview of the KODAK 8000C digital
panoramic and cephalometric units.
General Overview
IMPORTANT
The Cephalostat can be positioned either on the right or the
left side of the KODAK 8000 unit.
Mobile Components
Figure 2-1 illustrates the up and down movement of the KODAK 8000C digital
panoramic and cephalometric units mobile component and the rotation of the rotative
arm.
Figure 2–1 KODAK 8000 and KODAK 8000C Units Mobile Components
2–2 KODAK 8000C UNIT OVERVIEW

General Overview
General Functional Components
Figure 2-2 illustrates the general functional components of the KODAK 8000C digital
panoramic and cephalometric units.
Figure 2–2 KODAK 8000 and KODAK 8000C Units Functional Components
20
19
21
22
18
23
24
16
15
17
5
1
25
4a
14
29
2
4
28
3 3a 26
8 27
12
10
RJ45/1
RJ45/2
9
6 7 13
11
1 Height adjustment buttons 14 X-Ray source assembly

2 Control panel 15 Unit rotative arm
3 Hand Grip 16 Panoramic sensor
3a Temple supports control knob 17 Component to raise for Cephalometric mode
4 Chin rest base 18 ON/OFF button
4a Chin rest and bite block 19 Wall mounting brackets cover
5 Temple supports 20 Wall mounting brackets
6 Unit mains connecting terminal 21 Column upper cover
7 Green warning lamp (ready state indicator) 22 Panoramic head cover
8 Column connecting terminal 23 Cephalostat arm
General Overview
9 X-Ray remote control 24 Cephalometric end of the arm cover

10 Door safety switch 25 Cephalostat head and head top cover
11 PC hosting the imaging and the acquisition 26 Cephalostat head side cover
software
12 Ethernet outlet RJ45/1 27 Carbon fiber screen
13 LAN RJ45/2 28 Head clamps and ear cones
29 Nasion support

General Overview
Digital Sensor Locations
Figure 2-3 illustrates the locations of the digital panoramic and digital cephalometric
sensors of the KODAK 8000C digital panoramic and cephalometric units.
Figure 2–3 KODAK 8000 and KODAK 8000C Units Digital Sensor Locations
system
General Overview
Laser Locations
Figure 2-4 illustrates the location of the lasers of the KODAK 8000C digital panoramic
and cephalometric units.
Figure 2–4 KODAK 8000 and KODAK 8000C Units Laser Beam Locations
3 2
1 Mid-sagittal plane positioning laser beam

2 Frankfort plane positioning laser beam
3 Canine plane positioning laser beam
4 Cephalometric Frankfort plane positioning laser beam

Control Panel
Control Panel
The control panel is an alphanumeric, digital soft touch console. It allows the operator to
control certain unit functions. It also displays the operating parameters and error
messages.
Figure 2–5 Unit Control Panel
8 Digital Panoramic and Cephalometric System
kV mA S
1 2 3 4
1 X-Ray emission LED: Yellow, indicates the x-rays are being emitted.
2 Display Screen: Displays the current acquisition parameters and the error messages.
3 Reset button: Resets the unit arm to the initial position to enable the patient to enter
and exit the unit.
4 Laser beam button: Activates the laser positioning beams to correctly position the
patient.
X-Ray Remote Control Overview
X-Ray Remote Control Overview
The x- ray remote control enables you to launch a radiological image acquisition via the
exposure button from outside the x-ray room. You must press and hold the exposure
button until the end of acquisition. Premature release of the exposure button interrupts
the acquisition.
Figure 2–6 X-Ray Remote Control
1 Exposure button: launches image acquisition.

Positioning Accessories and Replacement Parts
The following accessories are used when positioning a patient. They are delivered with
the KODAK 8000 digital panoramic and KODAK 8000C digital panoramic and
cephalometric unit.
Table 2-1 and Table 2-2 list the panoramic and cephalometric positioning accessories.
Table 2–1 Panoramic Positioning Accessories and Replacement Parts
Accessory Description
Panoramic chin rest and TMJ x2
Maxillary sinus chin rest
TMJ x2 and TMJ x4 nose rest
Standard bite block
Bite block for edentulous patients
A set of right and left temple supports

x2
Single use sheaths for bite blocks

(500 pcs box)
Accessory Description
Head clamps with ear cones
x2
Nasion support

Chapter 3
KODAK 8000C PACKAGING
Standard Packaging
Table 3–1 Cephalometric Assembly Components
Box Components Dimension (mm) Weight
• Cephalostat head
• Cephalostat arm
• Cephalostat covers 1200mm (L) x 800mm (D) x 1180mm (H) 80 kg
• Documentation (User Guide and

Installation Guide)
Table 3–2 Components
Product Description Quantity

Cephalostat head 1
Standard Packaging
Table 3–2 Components (Continued)
Product Description Quantity

Cephalostat arm 1
Arm elbow tube 1
End of the arm cover 1
Head top cover 1
Head side cover 1
3–2 KODAK 8000C PACKAGING

Chapter 4
SITE PREPARATION BEFORE INSTALLATION
IMPORTANT
Prior to placing the order and before installation, carefully check the
following requirements for the x-ray room.
Standard Compliance
Install the unit in an x-ray room compliant with all official regulations applicable to
protection against radiation. This room must reduce the frequency interferences of the
30MHz to 1GHz band to at least 12db.
Environmental Requirements
Check the following ambient operating condition requirements of the x-ray room before
installing the unit:
• Temperatures: 5 ~35 °C
• Relative humidity: 30 ~ 85%
• Atmospheric pressure: 700 ~ 1060 hpa
Unit Dimensions
Unit Dimensions
406 mm 1261 mm
(15.98") (49.63")
306 mm
(12.05")
10 mm
(0.38")
1810 mm 440 mm
(71.3") (17.3")
The unit dimensions illustrated in the above figure are as follows:
• Maximum height of the unit (2315mm)

• Minimum (1687mm) and maximum (997mm) height of the chin rest
• Minimum (1022mm) and maximum (1712mm) height of the ear cones
• Width (2250mm) and depth (1261mm) of the unit
WARNING
If you need to add a base plate you must add 15mm to the height of the unit.
500
600
4–2 SITE PREPARATION BEFORE INSTALLATION

Electrical Requirements
WARNING*
You MUST select the operating voltage when placing an order. The
operating voltage CANNOT be modified on site.
The unit can operate at:
• 100/110/130 V 50/60 Hz
• 230/240 V 50/60 Hz
Table 4–1 Optional Operating Voltages of the Unit
Nominal voltage * Maximum line

Minimum Maximum
(no load) current
100 V - 130 V 90 V 143 V 20 A
230 V - 240 V 207 V 264 V 10 A
CAUTION
The power supply line must be equipped with a connection box that
ensures a constant connection. It must not be possible to connect the
unit to the power supply without using a tool. The unit must be
protected against any accidental disconnection.
If other units are installed on the same line, interference and voltage fluctuations can
cause the radiological unit to operate abnormally. We strongly recommend that a
separate electrical line be dedicated to supply power to the KODAK 8000C unit.
This line should be protected by a circuit breaker with a maximum current of:
• 16 A at 230/240 V
• 20 A at 110/130 V
• A differential circuit breaker of 30 mA
Figure 4–1 Electrical Diagram of the X-ray Room and Connections
G L N
13
4
L
1A
6 5
RJ45
K8000C
8
L N
12
10
7bis 9
L N
11
1 General mains 7bis X-ray warning lamp connecting terminal

2 Differential circuit breaker 8 Column connecting terminals
3 Red color actuator emergency stop push-button 9 X-ray remote control
4 Red color actuator emergency stop push-button 10 Door safety switch
5 Red warning lamp, power ON indicator 11 Mains outlet (for electric tools)
6 Unit mains connecting terminal 12 Ethernet outlet (RJ45/1)
7 Green warning lamp, ready state indicator 13 Contactor

A single-phase alternating current power supply is required.
The electrical installation specifications should be as follows:
Table 4–2 Electrical Installation Specifications
Supply Voltage 100V/110V

230V/240V
/ 130V
Frequency 50/60 Hz 50/60 Hz
Electrical supply 6 kW 6 kW
Line current 16A 20A
required
Cable cross-section For 30 m: For 10 m:
according to length
2.5 mm2 2.5 mm2
Max. line 0.5 0.12
impedance
Differential circuit
30 mA 30 mA
breaker (2)
Maximum current to 16A 20A Protect the power supply line with a
trip circuit breaker differential circuit breaker that trips at
maximum current.
Specifications of 2 250V 6A 250V 6A • Install these stop push-buttons to
red color actuator simultaneously, switch off the
UL listed UL listed
emergency stop current to the active conductors
push-button of the radiological installation and
(3) and (4) exclude any other electric
equipment.
• Locate (3) inside the x-ray room,
near the unit, for the operator to
quickly cut the power supply if
necessary.
• Locate (4) outside the x-ray room,
near the x-ray remote control for
the operator to quickly cut the
power supply if necessary.
• Maintain them in OFF (open)
position until a deliberate action
is performed.
Table 4–2 Electrical Installation Specifications (Continued)
Specifications of 60 W 60 W • Locate the red warning lamp (5)

the warning lamps outside the x-ray room to indicate
(5) and (7) the unit is active (1 lamp at each
access point).
• Locate the green warning lamp
(7) outside the x-ray room to
indicate the ready state of the
unit for acquisition.
Contactor (13) 16A-250V 20A-250V
UL listed UL listed
Door Safety Switch 1A / 250V 1A / 130V Optionally, connect the door safety
(9) switch (9) that deactivates the x-ray
remote control if the door remains
open.
Use the following switches:
Emergency Stop Switch:

Manufacturer: Cutler-Hammer
Ref: • E22AT111
• E22AT112
Contactor:
Manufacturer: Telemecanique
Ref: LC1 D4011 • F6 (110/130 V - 60 Hz)
• P5 (230/240 V - 50 Hz)
• U6 (230/240 V - 60 Hz)
IMPORTANT
If you cannot use the above manufacturer devices, use an equivalent
emergency switch and contactor in the UL list with the same
specifications. For more information, see UL 2601.1 clause 22.7.

X-Ray Room Requirement

IMPORTANT
Use an appropriate wall fixing system suitable for the type of wall
construction. See the examples below.
The following illustrations provide examples of wall types and fixations.
2x
2x
16 mm 16 mm
2x
2x
16 mm 16 mm
Table 4–3 X-Ray Room Requirements
Room Components Minimum Requirement Comments

Width of the door 75 cm (30")
Height of the ceiling 240 cm (95") If needed, a shorter column is possible by
special order.
Strength of the wall Withstanding an extraction force of 150 kPa at It is the responsibility of the installer to
each point of attachment. choose an appropriate fixing system that
withstands the extraction force.
Load-bearing capacity of the floor 500 kg/m2 The floor must be solid and flat.
Required space for the KODAK 8000 2350 (L) x 1950 (D) x 2400 (H) mm
and K8000C units
IMPORTANT
Install the unit where a minimum amount of space is provided to allow
easy access for the patient or the maintenance technician (see Figure
4-2).
Figure 4–2 Minimum X-Ray Room Space Configuration for K8000 and K8000C
RJ45/1
RJ45/2
MINI 2350 mm
(92.52")
MINI 500 mm
(19.68")
13
12 9 10 6 5 7bis 11
4 9 10
5 7
3 Red color actuator emergency stop push-button 9 X-ray remote control

4 Red color actuator emergency stop push-button 10 Door safety switch
5 Red warning lamp, power ON indicator 11 Mains outlet (for electrical tools)
6 Unit mains connecting terminal 12 Ethernet outlet (RJ45/1)
7 Green warning lamp, ready state indicator 13 Local Area Network (LAN), (RJ45/2)
7bis X-Ray warning lamp connecting terminal
WARNING
You MUST prepare the appropriate electrical requirements and
configurations of the x-ray room before installing the unit. You MUST
locate separately the following low voltage and high voltage
connections:
- Low Voltage: (12), (9), (10)
- High Voltage: (6), (5), (7bis)

Computer System Requirements
To keep you always updated on the latest evolution of the minimum computer system
requirements for KODAK 8000C system software, this section is posted on site
MyTrophytec: http://www.mytrophytec.com, as a separate document with edition
number. Before any intervention on the client’s site, check first the MyTrophytec site for
the latest edition.
IMPORTANT
It is MANDATORY to check that the computer system configuration is
compatible with the computer system requirements for the KODAK
8000C software. If necessary you MUST update your computer system
configuration. KODAK 8000C MUST be connected to the computer via
a point-to-point Ethernet link and not via a LAN. DO NOT place the
computer and the peripheral equipment connected to it in the
immediate vicinity of the patient in the unit. Leave at least 1.5 m
distance from the unit. The computer and the peripheral equipment
must conform to the IEC 60950 standard.

Chapter 5-
INSTALLING THE CEPHALOSTAT
Tool Requirements
The installer must supply the following tools:
• Power drill
• Screws and heavy duty fixings
• Spirit level
• Measuring tape
• Cutter
• Metric Allen keys
• Metric spanners
IMPORTANT
The tool references mentioned in this manual are ISO tool
references.
Technical Staff Requirements

The installation requires the following number of technicians:
Unit Component Technicians

Arm 2
Head 2
Opening the Box
Opening the Box
Before opening the cephalostat assembly box make sure that you have the required tool.
To open the cephalostat assembly box, follow these steps:
1. Remove the upper cardboard from the packaging. DO NOT cut through the
cardboard.
2. Remove the cephalostat arm.
3. Remove gently and set aside the cephalostat head cover.
4. Remove the protection elements. Lift off the packaging carton.
5. Remove gently the cephalostat head from the transport support and place it on the
ground.
6. Remove the other accessories.
5–2 INSTALLING THE CEPHALOSTAT

Installing the Cephalostat Unit
Before installing the cephalostat unit, make sure that:
• The unit is switched off.

• The head and generator covers are removed.
• You have the required tools.
Installing the Cephalostat Arm

To install the cephalostat unit, follow these steps:
IMPORTANT
Make sure that the wall mounting bracket’s hole (A) is the furthest
from the wall before installing the cephalostat unit.
1. With the help of 1 person, position the cephalostat arm on the rear of the mobile
component of the column. To attach the arm, insert the screws on the column on the
lower holes (A). Insert and then tighten the fixing screws (C).
13
2. Make sure that the tube (A) is for the appropriate side (by default it is for the right side
position of the ceph), if not, unscrew the fixing screws and reposition it for the
appropriate side. Insert all the way tube (A) inside the tube clamps (B) and screw in
the fixing nut.Tigten the fixing screws of the tube clamps (B).
4 mm

Installing the Cephalostat Head

3. With the help of 1 person, lift the cephalostat head and insert the elbow tube (A)
inside the elbow tube clamps. Insert the elbow tube (A) as far as:
• Left side ceph position, 7mm (B)

• Right side ceph position, 22mm (C)
6 mm
7 mm
22 mm
4. Screw the fixing screws but do not tighten them.
5. Correctly position the cephalostat head using a spirit level (C) placed as shown in the
figure. Tighten the fixing screws (B) to adjust with the spirit level (C).
4 mm
C B
6. Correctly position the cephalostat head using a spirit level (D) placed as shown in the
figure. Tighten the fixing screws (C) to adjust with to the spirit level (D).
2.5 mm
4 mm
6 mm
A
x1
C
B
C
x1

7. To adjust the height of the Cephalostat head, using a measurement tape, measure the
height from the floor to the middle of the collimator outlet (A). Measure the height
from the floor to the center of the ear cone ball (B). The measurements must be the
same (A = B). To adjust the height use the tube fixing nut (C), see step 2 of the
procedure.
A = B
8. Insert the cables (B) inside the elbow tube (A) tube.
Wiring the Cephalostat Head
9. Pull the cables out of the elbow tube (A). Remove the adhesive tape. Connect the
following wiring in the following order:
Cable ... On the ... To ...

(B) 967/Alim Lambda/CN1 Power supply board CN1
(C) Green and yellow cable Next to power supply box Ground screw
(D) Ethernet Pano (with ferrite) Control box Pano
(E) Ethernet Workstation (with ferrite) Control box Workstation
(F) A14/CJ802/J5 (with ferrite) Control box Synchro
D
A
2.5 mm

Wiring the Cephalostat to the Unit Head

10. Pull the cables out of the cephalostat arm. Pass the cables through the opening in the
column and attach them with a cable tie to avoid cable wear due to usage as shown
in the figure below. Connect the wiring in the following order:
B
39 40
CJ653
J4
E "R" J6
J10 A
J5
1
J9
CJ699
40 39
B
C
1
J9
CJ699
E "L"
J1 1
CJ664
J1 0
D
1
J21
Cable ... On the ... To ...

(A) 967/CJ653/J10 CJ653 J10
(B) Ethernet Pano Ethernet Pano
(C) Ethernet Workstation Ethernet Workstation
(D) CJ664/J21 CJ664 J21(adapter board CJ664 v4)
(E “R”) 39/CJ699/J9 & 40/CJ699/J9 CJ699 J9 (for right side ceph)
(E “L”) 39/CJ699/J9 & 40/CJ699/J9 CJ699 J9 (for left side ceph)
Post-Installation Control
Before the post-installation control, check that:
• The installation of the unit is complete.

• The installation of the KODAK dental imaging software is complete.
• You have the test tool.
• You have raised the digital sensor to ceph mode.
• The unit is on.
Adjusting the Cephalostat Head

Adjusting the Cephalostat Head Inclination
To adjust the cephalostat head inclination, follow these steps:
1. Position the head clamps in a frontal AP position.
2. Access the Cephalometric Acquisition Window. In the Program pane, click .
3. Launch an x-ray using the x-ray remote control. The head clamps must be correctly
and vertically positioned on the acquired x-ray image.

4. If needed, adjust the cephalostat head mechanically using the elbow tube for
horizontal inclination of the cepahlostat head. Untighten the fixing screws (A) slightly.
Use the fixing screws (B) to adjust the horizontal inclination. Tighten the fixing screws
(A) when you have reached the desired adjustment.
2.5 mm
4 mm
x4
A
x1
B
A
B
x1
Adjusting the Height of the Cephalostat Head

To adjust the height of the cephalostat head, follow these steps:
1. Position the head clamps in a lateral position.
3. Launch an x-ray using the x-ray remote control.
4. In the Imaging Window, on the drawing toolbar, click . On the acquired image,
draw a line from the bottom of the image to the center of the ball (ear cone). The
resulting value must be:
• Height: 30mm (± 5mm)

• Length: 110mm (± 5mm)
30 mm (± 5 mm)
110 mm (± 5 mm)

5. If needed, adjust the height, using the cephalostat arm screws (A). Untighten slightly
the screws (A) and lift the cephalostat head to the correct height. Tighten the
cephalostat arm screws (A).
x4
A
Adjusting the Ear Cones Alignment

To adjust the ear cones alignment, follow these steps:
1. Position the head clamps in a lateral position.
3. Launch an x-ray using the x-ray remote control. The ear cone ball (A) must be at the
center of the head clamps circle (B).
draw a line from the center of the ball (A) to the center of the circle (B). The resulting
value must be ±1.5mm.
+1.5 mm

5. If needed, adjust the cephalostat head mechanically:
• For a vertical adjustment, use the cephalostat arm screws (A).

• For a horizontal adjustment, use the elbow tube clamps screws (B).
4 mm
Adjusting the Nasion Support

To adjust the nasion support, follow these steps:
1. Lower the nasion support to a vertical position.
3. Launch an x-ray using the x-ray remote control. The nasion support must be
perpendicular to the ear cones.
draw a perpendicular line between the center of the ear cones and the nasion support
holes to check that the nasion support is positioned vertically. The resulting value
must be A = B ±3mm.
A B
3 mm
5. If needed, adjust the nasion support, using the nasion support fixing screws (A).
2 mm

Adjusting the Cephalometric Frankfurt Positioning Laser

To adjust the cephalometric Frankfurt positioning laser, follow these steps:
1. Remove the generator front cover.
2. Turn on the unit. On the control panel, press to turn on the positioning laser
beams.
3. Make sure that the cephalometric Frankfurt positioning laser beam is projected in the
middle of the ear cone.
4. If needed, adjust the laser using the fixing screw of the laser socket.
5. Replace the generator front cover.
Checking the Image Quality
To check the image quality, follow these steps:
1. Raise the nasion support.
2. Open the head clamps.
3. Position the image quality phantom (A) at the center of the digital sensor.
5. In the Parameter pane, select:
• 64 Kv
• 15 mA
• 0.4 s
6. Launch an x-ray to acquire an image.
7. In the Imaging Window, on the acquired image, zoom on the value grid (B) of the
image quality phantom (A). The resulting value clearly visible must be minimum 2.5
(right, left, center and bottom).
Check that there is no splitting lines of the grid of the image quality phantom.

8. Save the image. Use this image as reference for a later image quality verification.
Fitting the Covers
Fitting the Covers

WARNING
Before fitting the covers, you MUST switch off the unit.
Before fitting the covers, check that:
• All the screws in the wall and the floor have been tightened.
• All the screws attaching the head and the fixed arm to the column have been
tightened.
D
2x M5x20
B
2x M5x50
2x M5x15
C
E
2x M5x50
2x
M5x12
3 mm
To fit the covers, follow these steps:
1. Fit the upper cover (A) on the column. Fit the cover on the wall-bracket (B). Fit the
cover on the column connecting terminal (C) and tighten the fixing screws.

Fitting the Covers
2. Fit the head cover (D) of the unit to the head chassis and tighten the fixing screws.
3. Fit under the head cover (E) and tighten the fixing screws.
4. Fit the inside column cover (F) and position and attach securely the ON/OFF button
to the cover with the fixing screws. Screw and tighten the fixing screws of the column
cover.
You can fit the cephalometric covers now.
Fitting the Covers
Fitting the Cephalostat Covers

To fit the cephalostat covers, follow these steps:
1. Fit the cephalostat end of the arm cover (A) and screw the fixing screws.
2. Fit the cephalostat head side covers (B) and screw the fixing screws.
3. Fit the cephalostat head top cover (C) and screw the fixing screws.
C
M5x12
4x
2x
M5x16
M5x12
5x

Chapter 6
Maintenance
Annual Maintenance
We recommend that a general inspection of the unit should be carried out every year by
an approved dental systems technician.
The inspection should cover the following points:
• Check the attachment points to the floor and the wall.
• Check all the mobile components of the unit.
• Check the x-ray generator.
• Check the alignment of the x-ray.
• Make an image acquisition with the test tools and check the image.
• Check the focal trough and the symmetry.
• Check the degree of legibility of the labels.
• Check for damage to cables, covers, oil leaks, etc.
If the results of any of these inspections are unsatisfactory, refer to the Service Manual in
order to rectify any problems.
If there is any doubt, do not operate the unit.
Annual Maintenance
6–2 Maintenance

CS8000 K8000c Installation Guide Sm736 Ed02 en

Uploaded by

Copyright:

Available Formats

CS8000 K8000c Installation Guide Sm736 Ed02 en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CS8000 K8000c Installation Guide Sm736 Ed02 en

Uploaded by

Copyright:

Available Formats

KODAK 8000C Digital Panoramic and Cephalometric

Extraoral Imaging System

This document is originally written in English.

Authorized Representative in the European Community

2—KODAK 8000C UNIT OVERVIEW

3—KODAK 8000C PACKAGING

4—SITE PREPARATION BEFORE INSTALLATION

5—INSTALLING THE CEPHALOSTAT

Fitting the Cephalostat Covers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–22

Conventions in this Guide

The following special messages emphasize information or indicate potential risk to

1–2 About This Guide

• The unit head that contains all the electronic control

2–2 KODAK 8000C UNIT OVERVIEW

General Functional Components

1 Height adjustment buttons 14 X-Ray source assembly

9 X-Ray remote control 24 Cephalometric end of the arm cover

2–4 KODAK 8000C UNIT OVERVIEW

Digital Sensor Locations

1 Mid-sagittal plane positioning laser beam

2–6 KODAK 8000C UNIT OVERVIEW

Figure 2–5 Unit Control Panel

8 Digital Panoramic and Cephalometric System

X-Ray Remote Control Overview

Figure 2–6 X-Ray Remote Control

1 Exposure button: launches image acquisition.

2–8 KODAK 8000C UNIT OVERVIEW

Positioning Accessories and Replacement Parts

Table 2–1 Panoramic Positioning Accessories and Replacement Parts

Panoramic chin rest and TMJ x2

Maxillary sinus chin rest

TMJ x2 and TMJ x4 nose rest

Standard bite block

Bite block for edentulous patients

A set of right and left temple supports

Single use sheaths for bite blocks

Head clamps with ear cones

2–10 KODAK 8000C UNIT OVERVIEW

Table 3–1 Cephalometric Assembly Components

Box Components Dimension (mm) Weight

• Documentation (User Guide and

Table 3–2 Components

Product Description Quantity

Table 3–2 Components (Continued)

Product Description Quantity

Arm elbow tube 1

End of the arm cover 1

Head top cover 1

Head side cover 1

3–2 KODAK 8000C PACKAGING

The unit dimensions illustrated in the above figure are as follows:

• Maximum height of the unit (2315mm)

4–2 SITE PREPARATION BEFORE INSTALLATION

The unit can operate at:

Table 4–1 Optional Operating Voltages of the Unit

Nominal voltage * Maximum line

Figure 4–1 Electrical Diagram of the X-ray Room and Connections

1 General mains 7bis X-ray warning lamp connecting terminal

4–4 SITE PREPARATION BEFORE INSTALLATION