PARTS LIST

ITEM QTY PART NO. PART DESCRIPTION LENGTH UNIT WT. NET WT.
1 6 X-LWRM RING MOUNT WELDMENT 68.81 412.85
2 3 X-SV196L LONG PLATFORM WELDMENT 230.94 692.81
3 6 X-TBW T-BRACKET WELDMENT 13.60 81.60
4 6 SHCM-T CHAIN MOUNT TIGHTENER BRACKET 3 in 1.86 11.15
5 6 X-VSKL LONG SUPPORT WELDMENT FOR VSK REINFORCEMENTS 37.05 222.33
6 6 X-127594 FLAT DISK CLAMP PLATE 4" CENTERS (GALV.) 2.51 15.04
7 12 X-100064 CLAMP (4" V-CLAMP) GALVANIZED 0.92 11.06
8 3 320751-I 1/2" CHAIN SHACKLE 0.76 2.29
F
9 3 320601-I 5/8" TURNBUCKLE 2.63 7.89
A
10 6 320777-I 5/16" THIMBLE 0.06 0.36
11 12 320152-I 5/16" WIRE ROPE CLIP 1.32 15.78
12 3 AC516-10 5/16" AIRECRAFT CABLE 1.25 3.76
13 15 SCX4 CROSSOVER PLATE 8 1/2 in 6.02 90.32
14 12 SCX2 CROSSOVER PLATE 7 in 4.80 57.56
15 3 X-AHCP ANGLE HANDRAIL CORNER PLATE 12.92 38.76
17 3 P30174 2-7/8'' O.D. x 174" SCH. 40 PIPE 174 in 84.20 252.59
C 18 3 P3174 3-1/2" X 174" SCH 40 GALVANIZED PIPE 174 in 109.97 329.90
19 12 P30120 2-7/8" x 120" (2-1/2" SCH. 40) GALVANIZED PIPE 120 in 58.07 696.79
20 18 G58R-48 5/8" x 48" THREADED ROD (HDG.) 4.18 75.27
20 18 G58R-24 5/8" x 24" THREADED ROD (HDG.) 2.09 37.63
21 12 A582114 5/8'' x 2-1/4" HDG A325 HEX BOLT 2 1/4 in 0.31 3.75
22 12 A58234 5/8'' x 2-3/4" HDG A325 HEX BOLT 2 3/4 in 0.36 4.27
E
23 12 A58FW 5/8" HDG A325 FLATWASHER 0.03 0.41
24 60 G58LW 5/8" HDG LOCKWASHER 0.03 1.57
25 60 G58NUT 5/8'' HDG HEAVY 2H HEX NUT 0.13 7.79
26 6 G12112 1/2'' x 1-1/2" HDG HEX BOLT GR5 1/2 in 0.15 0.89
27 3 G12212 1/2'' x 2-1/2" HDG HEX BOLT GR5 2 1/2 in 0.20 0.61
28 12 G1204 1/2'' x 4" HDG HEX BOLT GR5 FULL THREAD 4 in 0.27 3.24
29 24 G12065 1/2'' x 6-1/2" HDG HEX BOLT GR5 FULL THREAD 5 1/2 in 0.41 9.83
30 84 X-UB1300 1/2" X 3" X 5" X 2" U-BOLT (HDG.) 0.67 56.19
G 31 36 X-UB1306 1/2" X 3-5/8" X 6" X 3" U-BOLT (HDG.) 0.83 29.82
D
32 288 G12FW 1/2" HDG USS FLATWASHER 3/32 in 0.03 9.82
33 285 G12LW 1/2" HDG LOCKWASHER 1/8 in 0.01 3.96
B 34 285 G12NUT 1/2'' HDG HEAVY 2H HEX NUT 0.07 20.41
35 1 HALO40 5,000 LB. MAINTENANCE TIE-OFF POINT 41.12 41.12
TOTAL WT. # 3249.41
19
18 19 34 33 32 30
2 7 34
13 1
30 32
14 34 17 34
32 20 22 21 29
3 33
33 33
33 30 24 23 24 32
31 34 2
32 32
34 32 25 24 25 33
32
30 31 18
33 15 25 34
33 4 6
17 5
34 34
DETAIL A DETAIL B DETAIL C DETAIL D DETAIL E DETAIL F DETAIL G
Locations:
TOLERANCE NOTES DESCRIPTION New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 14' 6" LOW PROFILE PLATFORM Engineering
Atlanta, GA
Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES ( 0.030") WITH TWELVE 2-7/8" ANTENNA MOUTING Support Team: Plymouth, IN
DRILLED AND GAS CUT HOLES ( 0.030") - NO CONING OF HOLES PIPES, REINFORCED HANDRAIL, AND CABLE 1-888-753-7446 Salem, OR
Dallas, TX
LASER CUT EDGES AND HOLES ( 0.010") - NO CONING OF HOLES valmont Tampa, FL
BENDS AND ANGLES ARE 1/2 DEGREE
ALL OTHER MACHINING ( 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

1 OF 3
ALL OTHER ASSEMBLY ( 0.060") CSL 10/17/2019 10/18/2019 RMQLP-4120-H10

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 10/18/2019 RMQLP-4120-H10
 174"

Y/2 Y/2
Y Y

TRIM OR OFFSET AS REQUIRED

MAX. 12"

13" TO 36"
POLE DIAMETER

120"
87"
ADJUSTABLE

48" MIN.

Locations:
TOLERANCE NOTES DESCRIPTION New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 14' 6" LOW PROFILE PLATFORM Engineering
Atlanta, GA
Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES ( 0.030") WITH TWELVE 2-7/8" ANTENNA MOUTING Support Team: Plymouth, IN
DRILLED AND GAS CUT HOLES ( 0.030") - NO CONING OF HOLES PIPES, REINFORCED HANDRAIL, AND CABLE 1-888-753-7446 Salem, OR
Dallas, TX
LASER CUT EDGES AND HOLES ( 0.010") - NO CONING OF HOLES valmont Tampa, FL
BENDS AND ANGLES ARE 1/2 DEGREE
ALL OTHER MACHINING ( 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

2 OF 3
ALL OTHER ASSEMBLY ( 0.060") CSL 10/17/2019 10/18/2019 RMQLP-4120-H10

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 10/18/2019 RMQLP-4120-H10
 USE REAR 9/16" HOLES
FOR 1/2" HARDWARE

35

DETAIL I

8 10 11 9 34 33 26 4 27 33 34
H

I
6"

MAX. 12"

H 13 29 32 33 34

SECTION H-H
NOTE:
SOME OBJECTS ARE TRANSPARENT FOR CLARITY

Locations:
TOLERANCE NOTES DESCRIPTION New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 14' 6" LOW PROFILE PLATFORM Engineering
Atlanta, GA
Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES ( 0.030") WITH TWELVE 2-7/8" ANTENNA MOUTING Support Team: Plymouth, IN
DRILLED AND GAS CUT HOLES ( 0.030") - NO CONING OF HOLES PIPES, REINFORCED HANDRAIL, AND CABLE 1-888-753-7446 Salem, OR
Dallas, TX
LASER CUT EDGES AND HOLES ( 0.010") - NO CONING OF HOLES valmont Tampa, FL
BENDS AND ANGLES ARE 1/2 DEGREE
ALL OTHER MACHINING ( 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

3 OF 3
ALL OTHER ASSEMBLY ( 0.060") CSL 10/17/2019 10/18/2019 RMQLP-4120-H10

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 10/18/2019 RMQLP-4120-H10