DATA SHEET

GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes GBU Unit: inch ( mm )

FEATURES .880(22.3)
.860(21.8)
• Plastic material has Underwriters Laboratory

.310(7.90)
.290(7.40)
.160(4.1)
Flammability Classification 94V-O
.140(3.5) .140(3.56)
• Ideal for printed circuit board .130(3.30)

.080(2.03)
.060(1.52)
• Reliable low cost construction utilizing molded plastic technique

.740(18.8)
.720(18.3)
• Surge overload rating: 200 Amperes peak

.085(2.16)
.065(1.65)
• High temperature soldering guaranteed:
.040(1.02)

.710(18.0)
.690(17.5)
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension .030(0.76)

.075(1.90)R
MECHANICAL DATA
Case: Reliable low cost construction utilizing .100(2.54)
.022(0.56)
.085(2.16)
molded plastic technique .018(0.46)
Terminals: Leads solderable per MIL-STD-202, .080(2.03)
.065(1.65)
Method 208
.190(4.83) .050(1.27)
Mounting position: Any
.210(5.33) .040(1.02)
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.

GBU10A GBU10B GBU10D GBU10G GBU10J GBU10K UNIT

Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V

Maximum RMS Input Voltage 35 70 140 280 420 560 V

Maximum DC Blocking Voltage 50 100 200 400 600 800 V

Maximum Average Forward TC=100°C

10.0 A
Rectified Output Current at

I2t Rating for fusing ( t<8.35ms) 127 A2sec

Peak Forward Surge Current single sine-wave superimposed on
200 Apk
rated load(JEDEC method)

Maximum Instantaneous Forward Voltage Drop per element at 5.0A 1.0 Vpk

Maximum Reverse Leakage at rated T A=25° 5.0 µA

CDc Blocking Voltage per element TC=100°C 500 µA

Typical Thermal Resistance per leg(Note 2) RθJA 8.6 °C / W

Typical Thermal Resistance per leg(Note 3) RθJC 3.1 °C / W

Operating and Storage Temperature Range, TJ,TSTG -55+150 °C

NOTES:

1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.

2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.

3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.

DATE : AUG.29.2002 PAGE . 1

 RATING AND CHARACTERISTIC CURVES

INSTANTANEOUS FORWARD CURRENT, AMPERES

AVERAGE FORWARD CURRENT

HEAT-SINK
MOUNTING, TC
(4X4X0.15) INCH
COPPER PLATE
5.0
AMPERES

TJ = 25
Pulse Width = 30uS
1% Duty Cycle

60Hz RESISTIVE OR
INDUCTIVE LOAD
MOUNTED ON 0.5X0.5 INCH
COPPER PC BOARD, TA
0.5"(12.7mm) LEAD LENGTH

TEMPERATURE INSTANTANEOUS FORWARD VOLTAGE, VOLTS

Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
Fig.2 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
FORWARD SURGE CURRENT, AMPERES pk
INSTANTNEOUS REVERSE CURRENT,

200

160
MICROAMPERES

(HALF SINE-WAVE)

120

80

40

NO. OF CYCLES AT 62Hz

PERCENT OF PEAK REVERSE VOLTAGE
Fig.4 - MAXIMUM NON-REPETITIVE PEAK
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
FORWARD SURGE CURRENT
CAPACITANCE, pF

TJ = 25
f = 1MHz
Visg = 50m Vp-p

REVERSE VOLTAGE, VOLTS

Fig.5 - TYPICAL JUNCTION CAPACITANCE PER ELEMENT

DATE : AUG.29.2002 PAGE . 2