Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 39 views

    Gewindebolzen m36 English Stand 130308

    Uploaded by

    Jiangchang Qiao
    This document provides notes on installing threaded anchor bars for concrete foundations. It specifies that the anchor bars, nuts, and washers must be from the same manufacturer and have a minimum length of 2m between plates. Inclined or horizontal bars must be protected from transverse loads. The steel cap and gasket are to be installed on the anchor plate and bolted in place. After installation, gaps below the baseplate are to be filled with non-shrink mortar. The surface of the anchor bars is to be wrapped with corrosion protection tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Gewindebolzen m36 English Stand 130308

    Uploaded by

    Jiangchang Qiao
    39 views1 page
    This document provides notes on installing threaded anchor bars for concrete foundations. It specifies that the anchor bars, nuts, and washers must be from the same manufacturer and have a minimum length of 2m between plates. Inclined or horizontal bars must be protected from transverse loads. The steel cap and gasket are to be installed on the anchor plate and bolted in place. After installation, gaps below the baseplate are to be filled with non-shrink mortar. The surface of the anchor bars is to be wrapped with corrosion protection tape.

    Original Title

    Gewindebolzen m36 English Stand 130308 (1)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides notes on installing threaded anchor bars for concrete foundations. It specifies that the anchor bars, nuts, and washers must be from the same manufacturer and have a minimum length of 2m between plates. Inclined or horizontal bars must be protected from transverse loads. The steel cap and gasket are to be installed on the anchor plate and bolted in place. After installation, gaps below the baseplate are to be filled with non-shrink mortar. The surface of the anchor bars is to be wrapped with corrosion protection tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    39 views1 page

    Gewindebolzen m36 English Stand 130308

    Uploaded by

    Jiangchang Qiao
    This document provides notes on installing threaded anchor bars for concrete foundations. It specifies that the anchor bars, nuts, and washers must be from the same manufacturer and have a minimum length of 2m between plates. Inclined or horizontal bars must be protected from transverse loads. The steel cap and gasket are to be installed on the anchor plate and bolted in place. After installation, gaps below the baseplate are to be filled with non-shrink mortar. The surface of the anchor bars is to be wrapped with corrosion protection tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    NOTES: THREADED BAR M 36 M1:5

    - THREADED BARS, HEXAGON NUTS AND WASHERS


    MUST BE FROM ONE SET OF THE SAME MANUFACTURER !! THREADED BAR M36 - 8.8 ISO 898-1
    - ANCHOR BARS SHALL HAVE A MINIMUM LENGTH OF L > 2m WITH HEXAGON-NUT ISO 4032 - M36 - FKL 8
    BETWEEN UPPER AND LOWER ANCHOR PLATE !!
    - INCLINED OR HORIZONTAL ANCHOR BARS HAVE TO BE
    AND WASHER ISO 7089 - 36 - 300 HV
    PROTECTED FROM TRANSVERSE LOADS WITH APPROPRIATE PRE-STRESSING FORCE P = 350 KN
    MEASURES (CALIBERS AND INTERMEDIATE SUPPORTS).
    HOT-DIP-GALVANIZED ISO 10684
    CONCRETE GRADE MIN. C30/37

    EXCESS-LENGTH AND HEIGHT OF STEEL CAP HAVE


    TEMPLATE T=8 SHALL BE CONNECTED TO ANCHOR-BARS
    USING HEXAGON NUTS ON BOTH SIDES (AND BE CONNECTED
    TO THE FORMWORK IF POSSIBLE)

    INSTALL STEEL CAP AND GASKET ON ANCHOR PLATE USING

    TO BE DEFINED INDIVIDUALLY.
    M8 5.6 AND FILL CAP WITH CORROSION PROTECTION COMPOUND > 100 160

    BOLT TENSIONING DEVICE / JACK MADE BY AS TECH


    TYPE HWS16112006 (ø94 x 120mm) OR SIMILAR
    25 10

    85

    PLEASE NOTE:
    CIRCULAR ANCHOR PLATE ø160 x 45 WITH BOREHOLE ø37
    105

    105
    CORROSION PROTECTION COMPOUND

    BASE PLATE A x B x T WITH BOREHOLES ø80mm TOP OF DENSO-TAPE


    45

    LUBRICATED ON THE UNDERSIDE


    T

    ø80
    AFTER INSTALLATION AND ADJUSTMENT OF STEEL
    STRUCTURE FILL GAP BELOW BASEPLATE (D > 50mm) TOP OF FOUNDATION
    D

    WITH NON-SHRINK POURABLE MORTAR OR PAGEL


    (MIN. C60/75). COMPLETE VENTING OF GAP MUST BE
    ENSURED BY MEANS OF APPROPRIATE MEASURES.

    SURFACE OF ANCHOR BAR SHALL BE WRAPPED WITH


    2 LAYERS OF COLD PROCESSIBLE WAX-VASELINE TAPE
    MADE OF ROT-RESISTANT SYNTHETIC FLEECE
    (E.G. DENSO-TEC OR SIMILAR)

    180
    ADD. REINF.
    50
    50

    HELICAL REINFORCEMENT 5 x ø12 BST 500S


    BOTTOM OF DENSO-TAPE
    50
    50

    LOWER ANCHOR PLATE 150 x 150 x 40 WITH BOREHOLE ø37


    100

    CONNECTED TO EACH OTHER WITH REBAR ø14 BST 500S


    TOP OF ANCHOR PLATE
    50
    40

    CONNECT ANCHOR PLATE TO ANCHOR-BARS USING


    HEXAGON NUTS ON BOTH SIDES
    > 150

    BOTTOM OF FOUNDATION

    > 260 > 200

    1 : 10 11.03.2013

    You might also like