2 IN 1 MOVING IRON MOVEMENT METER EQ - 96/144

Two in One Data Sheet

EQ - 96/144 EQ 96/144 2 in 1 Analogue Meters
With Moving Iron Movement

www.rishabh.co.in Page 1 of 4 Version : 1 / 01 / I / XV / 1111 / B

Application Continuously : 1.2 times rated voltage /current
Short duration
The moving iron panel meters, 2-in-1 housed in moulded Voltmeters : 2 times for 0.5 sec : 9 overloads
polycarbonate cases are suitable for the measurement of AC 2 times for 5 sec : 1 overload
currents for frequency range of 15...400Hz and voltages in the Ammeters : 10 times for 0.5 sec : 9 overloads
frequency range of 15...100Hz. 10 times for 5 sec : 1 overload
Moving iron meters indicate rms-values practically independent
of waveform even of high harmonics. Error of indication may occur Enclosure code : IP 52 case
(IEC 529) IP 00 for terminals without back cover
for extreme waveforms (e.g. phase gating controls) & for frequencies IP 20 for terminals with back cover
above 100Hz.
Insulation class : Group A according to VDE 0110
These meters offer several advantages in switchboards and
Generating Set Panels. Number of meters can be mounted in a Rated insulation voltage : 2 in 1 EQ
single cut out (Mosaic mounting). Front window, Glass and bezel 1000V
can be easily replaced. Proof voltage : 3KV
Installation category : 600V CAT III
Features
Insulation resistance : > 50 Mohm at 500 V DC
• Two different meters in one case.
• Near linear scale.
• Glass ¿lled polycarbonate housing(UL 94 V-0). Reference Conditions
• Easily replacable glass & bezel. Accuracy class : 1.5 according to IS : 1248
• Knife edge pointer (IEC 51/ DIN EN 60051)
Ambient temperature : 23 C 2 C
Position of use : Nominal position 1
Movement Input Waveform : Rated value of measured quantity
Moving iron movement has pivots of very high hardness. sine wave,distortion factor <= 5 %
Movement suspended between spring loaded saphire jewel and Frequency: : 45...65HZ
silicon jewel.Movement is critically damped by use of silicon oil. Other conditions : IS : 1248 (IEC 51/ DIN EN 60051)

Speci¿cations
Scale and Pointer Nominal Range of Use

Pointer : Knife - edge pointer Ambient Temperature : 0...50 C

Pointer deÀection : 0...90
Scale characteristics : Near Linear above 10% of nominal Position of use : Vertical 5
full Scale value Frequency : 45 ... 65Hz
Scale division : Coarse - ¿ne
Scale length : 54mm External magnetic ¿eld : At 0.4 kA/m
Over Range
Ammeters : 2 times nominal current
Voltmeters : 1.2 times nominal voltage Environmental Conditions
Climatic suitability : Climate category II
Mechanical Data as per IS : 1248, IEC 60051
Case details : Moulded square case suitable for (climatic class 3 according to
mounting in Control / switchgear VDE/VDI 3540)
panels Machinery consoles.
Case material : Polycarbonate , Operating temperature : - 10... + 55 C
Àame retardant and drip proof Storage temperature : - 25... + 65 C
as per UL 94 V-0. Relative humidity : -< 75% annual average,
Front facia : Glass non-condensing
Colour of bezel : Black Shock resistance : 15gn for pulse duration 11 ms
Position of use : Vertical Vibration resistance : 10-55-10Hz for ampli. 0.15mm
Panel ¿xing : Mounting Clamp (1.5 g at 50Hz)
Mounting : Stackable in a single cutout Pollution degree : 2
Panel thickness : 25 mm
Terminals
Voltmeters and : Hexagon studs, M4 screws and
Ammeters < 30A wire clamps E3 Standard Measuring Ranges
Ammeters > 30A : Threaded studs M6 with Nuts
A.C. Voltage A.C. Current
6V 100mA
10V 150mA
Electrical Data 15V 250mA
Measured quantity : ACvoltage or current 25V 400mA
Power consumption: 40V 600mA
Voltmeters : < 4.5VA 60V 1A
Ammeters < 15A : < 0.5VA 100V 1.5A
Ammeters > 15A : < 0.8 VA 120V 2.5A
Overload capacity : (acc. to IS: 1248 / IEC 51) 132V 3A

www.rishabh.co.in Page 2 of 4 Version : 1 / 01 / I / XV / 1111 / B

 150V 4A Accessories
250V 5A
300V 6A Safety Terminal Protection
400V 10A
500V 15A Full sized polycarbonate back cover to provide protection
600V 20A against accidental contact (hand and ¿ngers).
25A
30A
For use on voltage transformer 40A
50A Safety Precautions
.../100 V secondary
60A
.../110 V secondary For use with Current transformer
1) Instruments with damaged bezel or glasses must be
.../1A secondary or
disconnected from the mains.
.../5A secondary
Any combination Ammeter / Ammeter
Voltmeter / Voltmeter 2) Adequate safety clearance must be maintained to control
Ammeter / Voltmeter panel fasteners and to sheet metal housing. If non - insulated
In case of Ammeter / Ammeter 1 meter could be upto 60A but 2nd connector wires are used.
one will be only upto 10A
Non-Standard ranges available on request. 3) The back cover must be snapped into place after connector
wires have been clamped for protection against accidental
Options contact.
4) Bezel, Scale and Glass may only be replaced under voltage
Case
free conditions.
Front facia : Antiglare glass
Colour of bezel : Red, Yellow , Blue, White 5) Instruments to be used in grounded panel.
Red index pointer : Front adjustable on site
Position of use : On request 0 ...180

Dial
Blank dial With initial and end values marked.
Connections
:
Special markings : Numbering / Lettering. AC Voltage (Direct connected)
Division markings : Basic divisions without numbering.
Colour markings/bands : Red or green 11 12
Over range : Two, three and ¿ve times over range
(Ammeters) Six times over range L1
N(L2)

Applicable Standards AC Current (Direct connected) 11 12

Nominal case and cutout dimensions for : IS 2419
indicating Electrical instruments DIN 43700 L1

Scale and pointer for electrical measuring : IS 1248 N(L2)

instruments DIN 43802
AC Current (for use on current
Connections and Terminal markings for : IS 1248 11 12
Transformer)
panel meters DIN 43807
Terminal bolts / leads. : DIN 46200/ k l
46282
Safety requirements and protective : IS 9249 L1
measures for Electrical indicating. DIN 40050 K L
N(L2)
instruments and their accessories. VDE 0110
VDE 0410
IEC 529, IEC
1010 Dimensions
Performance speci¿cations for direct : IS 1248 For Voltmeters &
acting indicating analogue electrical IEC51/DINEN Ammeters upto 25A For Ammeters > 25A
60051
measuring instruments and their accessories DIN 43701
Environmental conditions : IS 1248
IS : 9000
VDE / VDI 3540
d b a d b a
Front frames for indicating measuring : DIN 43718
instruments Principle dimensions
UL Combustibility Class : UL 94 V-0
Comply with following European directives: : 2004 / 108 / EC
(EMC directive), 2006/95/EC (low voltage directive) & amendment c
93/68/EEC, For Marking. c e
f e f

www.rishabh.co.in Page 3 of 4 Version : 1 / 01 / I / XV / 1111 / B

 Dimensions EQ 96 EQ 144
(in mm) (in mm)
Bezel a 96 Bezel a 144
Case b 90 Case b 136
Depth c* 53 Depth c* 53
d 91.5 137.5
e 5.5 5.5
+0.8
cutout size 92 cutout size 138 +1
Depth with Depth with
back cover f ** 64 back cover f ** 64
* c = 62 mm, for l > 30A & upto 60A
Weight appro. 0.2 kg Weight appro. 0.4 kg

Ordering Information
Type DE Moving-iron panel meter Moving-iron panel meter

Front dimension
96 mm x 96 mm 144 mm x 144 mm
96
Over range 2 times, 3 times 2 times, 3 times
(Ammeters) 6 times, 5 times 6 times, 5 times
Measuring Ranges Refer to table inside Refer to table inside

Terminal protection full sized polycarbonate backcover full sized polycarbonate backcover

Panel Fixing Mounting Clamps Mounting Clamps

None *1
None *1
*3
Red Index Pointer Required
*3
Required

*1 *3
Housings color white, Black Black *1, White*3

Front facia Normal glass *1 Normal glass *1

Antiglare glass *3 Antiglare glass *3
*3 *3
Polycarbonate glass Polycarbonate glass

Colour of bezel Black *1 Black *1

Red,Blue,Yellow,White*3 Red,Blue,Yellow,White*3

Position of use Vertical *1 *3

Vertical *1 *3
On request 0 .... 180 On request 0 .... 180
Dial Standard scale same as measuring range *1 Standard scale same as measuring range*1
Blank dial with division *3 Blank dial with division *3
*3 *3
Additional lettering on request Additional lettering on request
*3 *3
Additional numbering on request Additional numbering on request
Coloured marking red or green *3 Coloured marking red or green *3

Coloured sector red or green*3 Coloured sector red or green*3

*1 *1
Logo RISHABH RISHABH

*1 standard
*3 Please clearly add the desired speci¿cations while ordering

Ordering example
EQ 30A - EQ 500V
EQ 300V - EQ 500V
EQ 30A - EQ 5A

Speci¿cations are subject to change without notice

RISHABH INSTRUMENTS PVT.LTD.

F-31, MIDC, Satpur, Nashik-422 007,India.
Tel.: +91 253 2202160, 2202202 Fax : +91 253 2351064
E-mail : India :- marketing@rishabh.co.in
International :- exp.marketing@rishabh.co.in
www.rishabh.co.in
www.rishabh.co.in Page 4 of 4 Version : 1 / 01 / I / XV / 1111 / B