Description of A Standard Bumper Jack

Description of a Standard Bumper Jack
Definition: term, The standard bumper jack is a portable mechanism for raising the front or rear of a car through
class, features, force applied with a lever. The jack enables even a frail person to lift one corner of a 2-ton
function automobile.
The jack consists of a molded steel base supporting a free-standing perpendicular, notched shaft
Overall (Figure 1). Attached to the shaft are a leverage mechanism, a bumper catch, and a cylinder for
description
insertion in the jack handle. Except for the main shaft and leverage mechanism, the jack is made
to be dismantled. All its parts file neatly in the car’s trunk.
Operating The jack operates on a leverage principle. During one normal jacking stroke, the operator’s hand
principle travels 18 inches and the car raises or lowers 3/8 of an inch. Such a device requires many
strokes to raise the car off the ground but may prove a lifesaver to a motorist on some deserted
road.
List of major Five main parts make up the jack: base, notched shaft, leverage mechanism, bumper catch, and
parts handle (Figure 1).
Description of Parts and their Functions

For each major Base. The rectangular base is a molded steel plate that provides support and a point of insertion
part include: for the shaft. The base slopes upward to form a platform containing a 1-inch depression that
provides a stabilizing well for the shaft. Stability is increased by a 1-inch cuff around the well. As
Definition, size, the base rests on its flat surface, the bottom end of the shaft is inserted into its stabilizing well.
shape, material,
location, color
Notched Shaft. The notched shaft is a steel bar (32 inches long) that provides a vertical track for
Function & mode the leverage mechanism. The notches, which hold the mechanism in position on the shaft, face
of attachment the operator. The shaft vertically supports the raised automobile. The leverage mechanism, which
is attached to the shaft, rests on individual notches.
Subparts, if any
Leverage Mechanism. The leverage mechanism provides the mechanical advantage needed
for the operator to raise the car. It is made to slide up and down the notched shaft. The main body
of this pressed-steel mechanism contains two units: one for transferring the leverage and one for
holding the bumper catch.
The holder consists of a downsloping groove, partially blocked by a wire spring. The spring is
mounted in such a way as to keep the bumper catch in place during operation.
As shown in Figure 1, the unit for transferring the leverage has four major parts:
 the cylinder, which connects the handle and a pivot point;
 a lower pawl, connected directly to the cylinder, that fits into the notches and allows
forward and prevents backward motion;
 an upper pawl, connected to the pivot point; and
 an “up-down” lever, which applies or releases pressure on the upper pawl by means of a
spring.
Bumper Catch. The bumper catch is a 9-inch molded plate that attaches the leverage
mechanism to the bumper and is bent to fit the shape of the bumper. Its outer ½ - inch is bent up
to form a lip, which hooks behind the bumper to hold the catch in place. the two sides of the plate
are bent back 90 degrees to leave a 2-inch bumper contact surface, and a bolt is riveted between
them. This bolt slips into the groove in the leverage mechanism and provides the attachment
between the leverage unit and the car.
Jack Handle. The jack handle is a steel bar that serves both as lever and lug bolt (or lugnut)
remover. This round bar is 22 inches long, 5/8-inch in diameter, and is bent 135 degrees roughly
5 inches from its outer end. Its outer end is a socket wrench made to fit the wheel’s lug bolts. Its
inner end is beveled to form a bladelike point for prying the wheel covers and for insertion into the
cylinder on the leverage mechanism.
Theory of Operation
Exert an up-down pumping motion on the jack handle. The leverage mechanism gradually climbs
One complete the vertical notched shaft until the car’s wheel is raised above the ground. When the lever is in
operating cycle the “down” position, the same pumping motion causes the leverage mechanism to descend the
shaft.

Description of A Standard Bumper Jack

Uploaded by

Copyright:

Available Formats

Description of A Standard Bumper Jack

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Description of A Standard Bumper Jack

Uploaded by

Copyright:

Available Formats

Description of a Standard Bumper Jack

Description of Parts and their Functions

You might also like