Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
324 views

BTP-2002NP Feed Button Program Guide V2.0

This document provides instructions for configuring the settings of a BTP-2002NP receipt printer through button presses on the device. It details accessing the configuration menu by holding the feed button at startup. The configuration menu has several submenus that allow changing settings like baud rate, data bits, stop bits, and more. Settings are saved by navigating back to the main menu. The summary provides an overview of the key configuration options and process.

Uploaded by

Hugo Martínez Moore
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
324 views

BTP-2002NP Feed Button Program Guide V2.0

This document provides instructions for configuring the settings of a BTP-2002NP receipt printer through button presses on the device. It details accessing the configuration menu by holding the feed button at startup. The configuration menu has several submenus that allow changing settings like baud rate, data bits, stop bits, and more. Settings are saved by navigating back to the main menu. The summary provides an overview of the key configuration options and process.

Uploaded by

Hugo Martínez Moore
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

BTP-2002NP RECEIPT PRINTER Feed Button Program Guide

Parameter Setting (Configuring) by Key-strokes


1) Hold the FEED button pressed while switching the printer on.
2) After the printer has printed the configuration sheet, press and hold the FEED button to
configure the printer. The main menu for the key-stroke setting procedure is printed.
3) The procedure consists of several sub-menus and step-by-step working is needed.
4) With every choice is a number. This number indicates the number of times the FEED button
has to be shortly pressed. After this, the choice is validated by an additional, but longer press
of the FEED button (1 sec).
5) After all settings have been done, they are stored in the printer by stepping back through the
submenus to the main menu by using the number “1” plus additional press for validation.

Parameter Setting by Key-strokes

Main Menu

Select submenu

Exit Print Self Test Configuration Cutter Test Sensor Test

>1 >2 >3 >4 >5

Setting Configuration of the Printer

Configuration

Exit Exit with Communic Mech. & Print Paper Set


without Save ation Hardware Settings Sensor Default
Save (only serial Setting Config
interface)
>1 >2 >3 >4 >5 >6 >7

-1-
Configuration of the Serial Interface

Communication

Back Baud Rates Parity Data Bits Stop Handshak- Rx Buffer Data
to last (default: (default: (default: Bit(s) ing Size Receive
menu 9600 bps) none) 8 bits) (default: (default: (default: Error
>2 1 Bit) DTR/DSR) 4k bytes) (default:
Choices: ignored)
>1 9600 bps >3 >4 >5 >6 >7 >8
19200 bps
38400 bps Choices: Choices: Choices: Choices: Choices: Choices:
57600 bps None 7 Bits 1 Bit DTR/DSR 4k bytes Ignored
4800 bps Odd 8 Bits 2 Bits XON/XOFF 45k bytes Print “?”
2400 bps Even
1200 bps
115200 bps
9600 bps
19200 bps
38400 bps
57600 bps
4800 bps
2400 bps
1200 bps

Setting Mechanism and Hardware


Mech. & Hardware

Back to last Mark Sensor Cutter Buzzer Power Supply


menu (default: (default: (default: (default:
disabled) enabled) enabled) normal)

>1 >2 >3 >4 >5

Choices: Choices: Choices: Choices:


Enabled Enabled Enabled Normal
Disabled Disabled Disabled Low power
mode

-2-
Print Setting

Print Setting

Back to Darkness Paper Left Right CR Code Page


last (default: Roll Margin Margin Command (default:
menu normal) Width (default: (default: (default: PC 437)
(default: 7 mm) 9 mm) disabled) >7
80 mm) Choices:
>1 >2 >3 >4 >5 >6 PC 437
PC 850
Choices: Choices: Choices: Choices: Choices: PC 852
Low 57.5 mm 0 mm 0 mm Enabled PC 858
Normal 69.5 mm 1 mm 1 mm Disabled PC 860
High 76.5 mm 3 mm 3 mm PC 863
Extra high 80.0 mm 5 mm 5 mm PC 865
82.5 mm 7 mm 7 mm PC 866
9 mm 9 mm PC 1252
Katakana

Paper Near-end Sensor Setting


Paper sensor settings

Paper Low Alarm Stop print when paper low


Back to last menu
(default: enabled) (default: disabled)

>2 >3
>1
Choices: Choices:
Enabled Enabled
Disabled Disabled

Set Default Configuration


Set default config

Back to last Menu Set printer to default config

>2
>1 Choices:
Enabled
Disabled

-3-

You might also like