09FO_US.

book 2 ページ ２０１３年９月２６日　木曜日　午前１０時５分

General Description
COOLING

1. General Description
A: SPECIFICATION
Electric fan + Forced engine coolant
Cooling system
circulation system
Non-turbo MT: approx. 6.8 (7.2, 6.0)
Total engine coolant capacity 2 (US qt, Imp qt) model AT: approx. 6.7 (7.1, 5.9)
Turbo model Approx. 7.5 (7.9, 6.6)
Type Centrifugal impeller type
Discharge rate 2 (US gal, Imp gal) /min 20 (5.3, 4.4)
Discharge performance I Pump speed — Discharge pressure 760 rpm — 2.9 kPa (0.3 mAq)
Engine coolant temperature 80°C (176°F)
Discharge rate 2 (US gal, Imp gal) /min 100 (26.4, 22.0)
Discharge performance II Pump speed — Discharge pressure 3,000 rpm — 49 kPa (5.0 mAq)
Water Engine coolant temperature 80°C (176°F)
pump Discharge rate 2 (US gal, Imp gal) /min 200 (52.8, 44.0)
Discharge performance III Pump speed — Discharge pressure 6,000 rpm — 225.4 kPa (23 mAq)
Engine coolant temperature 80°C (176°F)
Impeller diameter mm (in) 76 (2.99)
Number of impeller vanes 8
Pump pulley diameter mm (in) 60 (2.36)
Clearance between impeller and case Standard mm (in) 0.5 — 1.5 (0.020 — 0.060)
Type Wax pellet type
Starting temperature to open 80 — 84°C (176 — 183°F)
Thermostat Fully opens 95°C (203°F)
Valve lift mm (in) 9.0 (0.354) or more
Valve bore mm (in) 35 (1.38)
Main fan 90 W
Motor input
Radiator Sub fan 90 W
fan Main fan 300 mm (11.81 in)/4
Fan diameter / Blade
Sub fan 300 mm (11.81 in)/5
Type Down flow, pressure type
687.4 × 340 × 16
Core dimensions Width × Height × Thickness mm (in)
(27.06 × 13.39 × 0.63)
Radiator Above: 10815 or more
(1.10.15, 162)
Pressure range in which cap valve is open kPa (kg/cm2, psi)
Below: –1.0 to –4.9 or less
(–0.01 — –0.05, –0.1 — –0.7)
Fins Corrugated fin type
Reservoir
Capacity 2 (US qt, Imp qt) 0.45 (0.48, 0.40)
tank

Recommended materials Item number Alternative

SUBARU SUPER COOLANT (concentrated type) —
Coolant —
SUBARU SUPER COOLANT (dilution type) K0670Y0000
Water for dilution Distilled water — Soft water or tap water
Cooling system protective agent Cooling system conditioner SOA345001 —

CO(H4SO)-2
09FO_US.book 3 ページ ２０１３年９月２６日　木曜日　午前１０時５分

General Description
COOLING

B: COMPONENT
1. WATER PUMP

(2)

(1)

T1

(7)

T1 (3)

(7)
(4)

T2 (5)

(6)

CO-02484

(1) Water pump ASSY (5) Gasket Tightening torque:N·m (kgf-m, ft-lb)
(2) Gasket (6) Thermostat cover T1: First 12 (1.2, 8.9)
(3) Heater by-pass hose (7) Clip Second 12 (1.2, 8.9)
(4) Thermostat T2: 12 (1.2, 8.9)

CO(H4SO)-3
09FO_US.book 4 ページ ２０１３年９月２６日　木曜日　午前１０時５分

General Description
COOLING

2. RADIATOR & RADIATOR FAN

T2
(5) T1
(6)

(5)

T3 T2
(8)
T1
(10)
T4

(7)

(4) (11)
T5
(3)
T4
(12)

(24)
(13)
(9)

(25)
(2) T2

B (14)
(16) (15)
T2
(5) (20)
A
(22)

(21) (17) (14)

(14) T2
(1) (5)
B

(14)
(23) A (18)

(19)

CO-02467

(1) Radiator lower cushion (12) Radiator main fan shroud (22) O-ring
(2) Radiator (13) Radiator main fan, radiator main (23) Radiator lower bracket
(3) Radiator upper cushion fan motor ASSY (24) Radiator cap
(4) Radiator upper bracket (14) ATF hose clamp (AT model) (25) Heat shield cover (AT model)
(5) Clamp (15) ATF hose A (AT model)
(6) Radiator inlet hose (16) ATF hose B (AT model) Tightening torque:N·m (kgf-m, ft-lb)
(7) Engine coolant reservoir tank cap (17) ATF pipe (AT model) T1: 5 (0.5, 3.7)
(8) Over flow hose (18) ATF hose C (AT model) T2: 7.5 (0.8, 5.5)
(9) Engine coolant reservoir tank (19) ATF hose D (AT model) T3: 12 (1.2, 8.9)
(10) Radiator sub fan shroud (20) Radiator outlet hose T4: 3.4 (0.3, 2.5)
(11) Radiator sub fan, radiator sub fan (21) Radiator drain plug T5: 3 (0.3, 2.2)
motor ASSY

CO(H4SO)-4
09FO_US.book 5 ページ ２０１３年９月２６日　木曜日　午前１０時５分

General Description
COOLING

C: CAUTION
• Wear appropriate work clothing, including a cap,
protective goggles and protective shoes when per-
forming any work.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Vehicle components are extremely hot after driv-
ing. Be wary of receiving burns from heated parts.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Before disconnecting connectors of sensors or
units, be sure to disconnect the ground cable from
the battery.
• Prepare a container and cloth to prevent scatter-
ing of engine coolant when performing work where
engine coolant can be spilled. If the fuel spills, wipe
it off immediately to prevent from penetrating into
floor or flowing out for environmental protection.
• Follow all government and local regulations con-
cerning disposal of refuse when disposing engine
coolant.

CO(H4SO)-5
09FO_US.book 6 ページ ２０１３年９月２６日　木曜日　午前１０時５分

General Description
COOLING

D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
499977100 CRANK PULLEY Used to stop rotation of the crank pulley when
WRENCH loosening or tightening crank pulley bolts. (MT
model)

ST-499977100
499977400 CRANK PULLEY Used to stop rotation of the crank pulley when
WRENCH loosening or tightening crank pulley bolts. (AT
model)

ST-499977400
18231AA010 CAM SPROCKET • Used for removing and installing cam sprocket.
WRENCH • CAM SPROCKET WRENCH (499207100) can
also be used.

ST18231AA010
1B022XU0 SUBARU SELECT Used for troubleshooting for electrical system.
(Newly adopted tool) MONITOR III KIT

ST1B022XU0

CO(H4SO)-6