TECHNICAL SPECIFICATION

CARBON STEEL FORGINGS

(AMENDMENTS/SUPPLEMENTS TO ASTM A 105)

MESC SPE 76/210

June 2007

MESC SPECIFICATION DOCUMENT

This document is restricted. Neither the whole nor any part of this document may be disclosed to any third party without the prior written consent of Shell Global
Solutions International B.V., The Netherlands. The copyright of this document is vested in this company. All rights reserved. Neither the whole nor any part of this
document may be reproduced, stored in any retrieval system or transmitted in any form or by any means (electronic, mechanical, reprographic, recording or otherwise)
without the prior written consent of the copyright owner.
 MESC SPE 76/210
June 2007
Page 2

PREFACE

MESC (Materials and Equipment Standards and Code) SPE documents reflect the views, at the time of publication, of:
Shell Global Solutions International B.V. (Shell GSI)
and/or
Shell International Exploration and Production B.V. (SIEP)
and/or
other Shell Service Companies.
They are based on the experience acquired during their involvement with the design, construction, operation and
maintenance of processing units and facilities, and they are supplemented with the experience of Shell Operating Units.
Where appropriate they are based on, or reference is made to, international, regional, national and industry standards.
The objective is to set the recommended standard for good design and engineering practice applied by Shell companies
operating an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other such
facility, and thereby to achieve maximum technical and economic benefit from standardization.
The information set forth in these publications is provided to Shell companies for their consideration and decision to
implement. This is of particular importance where MESC SPEs may not cover every requirement or diversity of condition
at each locality. The system of MESC SPEs is expected to be sufficiently flexible to allow individual Operating Units to
adapt the information set forth in MESC SPEs to their own environment and requirements.
When Contractors or Manufacturers/Suppliers use MESC SPEs they shall be solely responsible for the quality of work
and the attainment of the required design and engineering standards. In particular, for those requirements not
specifically covered, the Principal will expect them to follow those practices, which will achieve the same level of
integrity as reflected in the MESC SPEs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting
from his own responsibility, consult the Principal or its technical advisor.
The right to use MESC SPEs is granted by Shell GSI, in most cases under Service Agreements primarily with Shell
companies and other companies receiving technical advice and services from Shell GSI or another Shell Service
Company. Consequently, three categories of users of MESC SPEs can be distinguished:
1) Operating Units having a Service Agreement with Shell GSI or other Shell Service Company. The use of MESC
SPEs by these Operating Units is subject in all respects to the terms and conditions of the relevant Service
Agreement.
2) Other parties who are authorized to use MESC SPEs subject to appropriate contractual arrangements (whether
as part of a Service Agreement or otherwise).
3) Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to under 1) or 2)
which requires that tenders for projects, materials supplied or - generally - work performed on behalf of the said
users comply with the relevant standards.
Subject to any particular terms and conditions as may be set forth in specific agreements with users, Shell GSI
disclaims any liability of whatsoever nature for any damage (including injury or death) suffered by any company or
person whomsoever as a result of or in connection with the use, application or implementation of any MESC SPE,
combination of MESC SPEs or any part thereof, even if it is wholly or partly caused by negligence on the part of Shell
GSI or other Shell Service Company. The benefit of this disclaimer shall inure in all respects to Shell GSI and/or any
Shell Service Company, or companies affiliated to these companies, that may issue MESC SPEs or require the use of
MESC SPEs.
Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, MESC
SPEs shall not, without the prior written consent of Shell GSI, be disclosed by users to any company or person
whomsoever and the MESC SPEs shall be used exclusively for the purpose for which they have been provided to the
user. They shall be returned after use, including any copies, which shall only be made by users with the express prior
written consent of Shell GSI. The copyright of MESC SPEs vests in Shell GSI. Users shall arrange for MESC SPEs to
be held in safe custody and Shell GSI may at any time require information satisfactory to them in order to ascertain how
users implement this requirement.
All administrative queries should be directed to the MESC SPE Administrator in Shell GSI.
 MESC SPE 76/210
June 2007
Page 3

TABLE OF CONTENTS
PART I INTRODUCTION ........................................................................................................4
1.1 SCOPE........................................................................................................................4
1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS .........4
1.3 DEFINITIONS .............................................................................................................4
1.4 CHANGES SINCE PREVIOUS EDITION...................................................................4
1.5 COMMENTS ON THIS MESC SPE............................................................................5
PART II AMENDMENTS/SUPPLEMENTS TO ASTM A 105:2005..........................................6
PART III REFERENCES ...........................................................................................................7
 MESC SPE 76/210
June 2007
Page 4

PART I INTRODUCTION

1.1 SCOPE
This MESC SPE specifies requirements for carbon steel forgings.
This specification shall apply in addition to the applicable MESC Buying Description,
purchase order or requisition sheet.
This specification only applies to carbon steel forgings to ASTM A 105.
This specification is written as amendments and supplements to ASTM A 105:2005, which
are covered in Part II of this MESC SPE. The clause numbering of ASTM A 105:2005 has
been retained and any amendments are identified as ‘Add’, ‘Modify to read’ or ‘Delete’. Any
clauses of ASTM A 105:2005 that are not amended or supplemented by this MESC SPE,
shall apply as written.

1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS

Unless otherwise authorised by Shell GSI, the distribution of this MESC SPE is confined to
Shell companies and, where necessary, to Contractors and Manufacturers/Suppliers
nominated by them.
This MESC SPE is intended for use in oil refineries, chemical plants, gas plants, exploration
and production facilities and, where applicable, supply/distribution installations.
If national and/or local regulations exist in which some of the requirements may be more
stringent than in this MESC SPE the Contractor shall determine by careful scrutiny which of
the requirements are the more stringent and which combination of requirements will be
acceptable with regards to safety, environmental, economic and legal aspects. In all cases
the Contractor shall inform the Principal of any deviation from the requirements of this
MESC SPE which is considered to be necessary in order to comply with national and/or
local regulations. The Principal may then negotiate with the Authorities concerned, the
objective being to obtain agreement to follow this MESC SPE as closely as possible.

1.3 DEFINITIONS
The Contractor is the party that carries out all or part of the design, engineering,
procurement, construction, commissioning or management of a project, or operation or
maintenance of a facility. The Principal may undertake all or part of the duties of the
Contractor.
The Manufacturer/Supplier is the party that manufactures or supplies equipment and
services to perform the duties specified by the Contractor.
The Principal is the party that initiates the project and ultimately pays for its design and
construction. The Principal will generally specify the technical requirements. The Principal
may also include an agent or consultant authorised to act for, and on behalf of, the
Principal.
The word shall indicates a requirement.
The word should indicates a recommendation.

1.4 CHANGES SINCE PREVIOUS EDITION

The requirements for forgings used to be part of the MESC SPEs for the component the
forging was made in. For instance: MESC SPE 76/002 (dated May 2006) contained
requirements for flanges and for forgings. The design requirements for flanges have now
been contained in MESC SPEs 76/100 and 76/101, respectively written as amendments
and supplements to ASME B16.5 and ASME B16.47. The material requirements have been
contained in a new set of MESC SPEs. These documents have been edited and written in a
new format, while their content has largely remained unchanged.
 MESC SPE 76/210
June 2007
Page 5

1.5 COMMENTS ON THIS MESC SPE

Comments on this MESC SPE may be sent to the MESC SPE Administrator at
standards@shell.com. Shell staff may also post comments on this MESC SPE on the
Surface Global Network (SGN) under the Standards folder.
 MESC SPE 76/210
June 2007
Page 6

PART II AMENDMENTS/SUPPLEMENTS TO ASTM A 105:2005

4.3 Add If galvanising is specified, galvanising shall be in accordance with ASTM A 153,
Grade B.
5.1 Modify to read:
Supplementary requirement S2.1 shall apply.
5.2 Modify to read:
Forgings shall be normalised.
6.1 Add:
The following restrictions in the chemical composition shall apply:
- The carbon content shall not exceed 0.23 %.
- Supplementary requirement S4 shall apply, except that CE shall not exceed
0.43.
 MESC SPE 76/210
June 2007
Page 7

PART III REFERENCES

In this MESC SPE, reference is made to the following publications:

NOTES:
1. Unless specifically designated by date, the latest edition of each publication shall be used, together with any
amendments/supplements/revisions thereto.
2. Most of the referenced external standards are available to Shell staff on the SWW (Shell Wide Web) at
http://sww05.europe.shell.com/standards.

SHELL STANDARDS
Flanges MESC SPE 76/002:2006
Flanges to ASME B16.5 MESC SPE 76/100
Flanges to ASME B16.47 MESC SPE 76/101
AMERICAN STANDARDS
Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS ASME B16.5
24 Metric/Inch Standard
Large Diameter Steel Flanges NPS 26 Through NPS 60 ASME B16.47
Issued by:
American Society of Mechnical Engineers
ASME International
Three Park Avenue, M/S 10E
New York, NY 10016, USA

Standard Specification for Carbon Steel Forgings for ASTM A 105:2005

Piping Applications
Standard Specification for Zinc Coating (Hot-Dip) on Iron ASTM A 153
and Steel Hardware
Issued by:
American Society for Testing and Materials
100 Barr Harbor Drive, West Conshohocken
PA 19428-2959
USA