P O I N T S E V E N

S H I E L D E DR E F E R E N C E
MONITOR

REFEREilCE
IUNilUAt

lQt ==19
P O I N T S E V E N -
S H I E L D E DR E F E R E N C M
EONITOR

RereneilcE
Mnnuru.

At-g.sits
1996
Intloduction
Thank you for purchasing the Alesis Point Seven Shielded Reference Monitors. To
take full advantage of the Point seven's operation, and to enjoy long and trouble.ftee
use, please read this user's manual carefully.

How To Use This Manual

This manual is divided into the following sections describing the various features of
the Point Sevens. Though we recommend you take time to read through the entire
manual once carefrrlly, those having general knowledge about monitors should use
the table of contents to reference specific functions.

Chapter 1: About the Point Seven. Engineering specifications and redsons why near
field monitors have become so popular.

Chapter 2: Speaker Installation. This chapter explains how to connect the Point
Sevens to a power amplifier and discusses proper speaker placement.

Chapter 3: Troubleshooting. This chapter contains troubleshooting tips and service

information should problems occur.

Wher somethingimportantaryearsin themanrul, an icon(Iike theoneon thl W) rlrill

appearin theleft margin. Thissymbolindicatesthat this infomution is oital whanoperating
thePoint Smm.

Point Seven Reference Manual

 C€
DECI.ARATIOIU OF COilFORMTTY

Manufacturer's Name: Alesis Corporation

Manuf acturer's Address: 3530Holdrege Ave.

Los Angeles,CA90016
USA

ileclares,that tlrc product:

Product Name: Point Seven

conformsto thefollouing Standanls:

EMC: EN55013:1990 Class B

EN55020:1988 sections4.3,5.4,5.2,
7.0 & 8.0 are under consideration

European Contact: Sound Technology

17 Letchworth Point, Lechworth,
Hertfordshire, SG61ND,
England.
Phone:+4.162.480ffi0
Fax: +M;1.462.480800

October, 1996
 Contents

About the Point Seven ..........,

Unpacking and lnspection

Spcaker Installatlon ................. ......... tl

Speaker Placement....

About Wire .....................-

t4

Troubleshooting

17

Point Seven Reference Manual

 About the Point Seven- Chapter 1

CHAPTER 1

Aeour rHE Polur S=v=lu

Unpacking and lnspection
Your Point Sevens were packed carefully at the factory, and the shipping carton was
designed to protect the speakers during shipping. Please retain this container in the
highly unlikely event that you need to retum the Point Sevens for servicing.

The shipping carton should contain the following items:

o This instruction manual
. Alesis Point Sevens with the same serial number as shown on shipping carton
o Port Plugs (for use with Subwoofers)
o Alesis warranty card

It is important to register your purchase; if you lnae not alruily flleil out your warranty
caril anil maikd it back ta Alesis, pleasetake the time to do so nou.

The Point Sevens are symekically designed, avoiding the need for mirror-imaged
pairs. The Point Seven speakers you receive should be identical on the left and right
sides.

Engineering Stdement
Your new Alesis Point Seven Shielded Reference Monitors are intended for very
space linited recording environments, for use in close proxirnity to a computer
monitor or when portability is a requirement.

Tonally, every effort has been made to emulate the accurate studio sound of Alesis'
own Monitor One with slightly less deep bass extension. The "Point Seven"
desigrration refers to the Seven's 5 | / 4" woofer piston area as being seven tenths the
piston area of the Monitor One's 6 1./ 2" woofer. The Point Seven's newly developed
silk doqne tweeter offers a frequency response to 27kHz, which has been tailored
specifically for non-fatiguing near-field monitoring.

lf you're in a hurry to get starteil with thc Point Seoens, skip ahead to Chapter 2, "spealcer
Instalhtion" , for connection and placerneflt tips.

The Point Seven's 5 1/ 4" woofer cone is made of proprietary non-woven carbon fiber.
This material is 25% lighter than polypropylene with twice the stiffness for quicker
transient response in the low-to-midbass region and improved midrange
intelfigibility. The non-woven carbon fiber cone, along with the closed cell synthetic
rubber surround, are both materials which are nearly impervious to ozone, direct
sunlight, heat and humidity. Therefore, after the initial break-in period (about 20
hours), the sound should remain virtually unchanged for the life of the product.

The Seven's shield"d t*""t"r ntt'tt.es a vented pole piece with a separate rear
chamber to lower the free air resonance. This high Q (very highly damped) design
feafures a pure silk dome, an intemal pole-piece-mounted phasing plug and low
viscosity ferrofluid formulated specifically to retain the best balance of transient
respons€ to power handling.

Point Seven Reference Manual

Chapter 1 - About the Point Seven

The frequency response of Alesis' ProPrietary tweeter is designed to be flat (t 2 dB]

from itJ2kHz crossover frequency to 10kHz. At 10kHz the response drops smoothly
to Z7kJl.lz, at which point it drops by -6d8. This is an optimal response for non-
fatiguing, long term, high levef nearfield mixdowns. This desigp results in a flat,
linear mix when played back on home or car systems from appropriate distances.

Magpetic shielding of both the Point Seven's drivers was not an afterthought. Rather,
from design inceptioo the system had to exhibit less than three gauss leakage so that
even extremely sensitive 21" computer monitors would be unaffected by close
proximity positioning. Shielding of both woofer and tweete! is accomplished by the
'bucking" magnet, plus a sixteen gauge steel
use of a second opposing-field-oriented
cup which encases the entire matnetic structure.

The eleven element crossover features modified algorithm third order Butterworth
filters for both the high and low pass sections along with woofer impedance
compensation. (Compensation is unnecessary on the tweeter. The tweeter's
impedance characteristic is exceptionally flat as desigrred and the resonance peak is
ahlady very effectively damped with the ferrofluid.) The crossover frequency of the
Point Seven is 2OOOHz.The actual voltage curve, however, shows the woofer
beginning its rolloff at 800H2 @ 6dB / octave to 1600H2. At this point the curve
"knees"
a second time and from 1600H2 to 3200H2 the rate is l2dBloctave.

"knees"
The tweeter voltage cuwe also twice but the curves are substantially steePer.
From 3400H2 down to 1700H2 the tweeter rolls at l2dBloctave. Below 1700H2 the
acoustic rolloffs approaches 60dB/octave. This radical curve shaping yields a tweeter
with prodigious power handling capability, even at the extrenely low 2kllz
crossover point. (Note that the slightly non-complementary curve slope spreads of
1.600H2-3200H2 for the woofer versus 3400H2-1700H2 for the tweeter are the
"offset"
acoustical required to compensate for mechanical offset of the woofer and
"offset"
tweeter. It is this or frequency spread which brings both drivers into proper
"altered
time alignment.) The advantages of these algorithm" high and low pass
Butterworth alignments are:

a) a virtually perfect group delay characteristic (almost a straight tine) yielding

accurate phase.
b) exceptionally linear power response (several averaged, off-axis frequency
response curves) through the rniddle octaves. Along with the 5 1./4" cone size this
"sweet
linear (Ilat) power response projects an exceptionally large spot".
c) a longer smoother, sound characteristic blend between the non-woven CF woofer
and silk dome tweeter.

The Point Seven's cabinet conskuction employs Alesis'proprietary non-skid rubber-

vinyl composite material laminated to a .625" MFD (medium density fiberboard)
core. The eight comer protectors used on our Monitor Two have been adapted to the
Point Seven in anticipation of its portable application.

Dual, front baffle mounted, 9" long ports have been carefuIly integrated to yield a
Qtc = 1.2 (a 3dB bump @ 120I{z) which provides a balanced, full range sound when
"port
used alone. For critical mixing/playback, recessed head, polyethylene plugs"
are provided. The plugs transform the Point Seven into an acoustic suspension
design giving a more critically damped response (Qtc = .9) and improved transient
"convertible"
characteristics. This versatile, ported/closed box feature is Possible
because the woofer's EBP (E{ficiency Bandwidth Product has been designed to fall
into the narrow paramete! range wherein both configurations will work equally well.

Point Seven Refermce Manual

 About the Point Seven- Chapter 1

A Liltle History
br the early days of recording, most recording studios used big monitor speakers
almost exclusively. Unfortunately, they also required high powered amplifiers and
expensive acoustic treatment (often poorly done) of.the entire control room. Still, a
well-constructed big monitoring system really was impressive to listen to, a fact not
overlooked by the studio owners who wanted to imPress the record company
executives who paid for the big studio's time. These big systems had big level
"cranking-up"
control knobs, and clients enjoyed the volume. Fortunately, recording
engineers and producers eventually leamed that this was not the best way to
accurately rrix music because it wasn't the way most people listened to their radios,
cassettes and C-D,players. Also, big monitor systems and the costs for the required
qonh.el:room,acorrstg-treatments were going through the roof (no pun intended),
parircularly,b€yond!&e brrdget limits of smaller project and home studios which
were growing in numbprs, Aner4{ way of accurate monitoring was needed: near-field
monitoring.

Near-field monitors, by their definition, are intended for mounting close to the
listener. The idea here is to improve the direct acoustic path between the speaker
and the listener by making it shorter, thereby giving less opportunity for the always
present indirect (reflected) sounds to get back in and muddle things up. With near-
field monitoring, the surrounding acoustic environment becomes a much less
significant factor in establishing the monitor system's sound character.

A good set of small monitors properly placed in a reasonably non-reverberant room

and poweled by a 1*watt amplifier will yield surprisingly accurate results at
budget prices. CarrM to another studio, the same monitor should also provide
repeatablereults" In fact, some recording engineers carry their own speakers around
because they know how they will sound in almost any room. Now, even the big
studios use smaller speakers to augment their big monitoring systems, and near-field
monitors have become proven tools in the recording business.

Point Seven Reference Manual

 Speakerlnstallation - Chapter 2

CIIAPTER 2

SpemER lnsrnl.r.nrroru
Like any speakersystem,your Point Sevenswill work best when properly positioned
in a suitableacousticenvironment.Achieving proper speakerplacementis usually
straightforward, but even with near-field monitors, speakerplacement and the
acousticsof the listening room itself are too often overlooked and can become
significant contributors to an inaccurate and uninspiring monitoring environment.

Speaker Placement
While near-field monitors are more forgiving of the surrounding room acoustics, it is
always prudent to optimize the listening environment whenever possible. First, the
user should be aware of the effect that the size of the listening room can have on low
frequency response. ln generaf the smaller the room, the stronger the bottom end
will be, although placement within a larger room can also make a difference. This
has to do with the way low-frequency waves travel in closed spaces. If you find your
monitor system to be either light or heavy on the bottom, try moving them around
within your lstening room.

You should avoid locating your Point Sevens near reflective surfaces such as glass,
tile, large open walls or table tops. Sti[ many rooms used for recording have these
surfaces, so the best way to deal with them is to place the monitors out in the room
away from reflective walls, windows and sizable objects. Even with these reflective
surfaces separated from the monitoring positiory typical mixing situations usually
still have the top surface of the mixing board to deal with.

Unfortunately, the board itself can be a major source of reflections and the additional
acoustic conduction into the board can affect your monitor's amplitude and phase
response. Speaker placement on the console's meter bridge provides for two clear
acoustic paths between the speakers and the recording engineer which results in
undesirable comb filtering effects and poor imaging. The first path is the direct one,
and the second is via a reflection off the mixer main control panel:

Monitorsplacedon the console'smeterbridgecan directly radiate

backonto the consolecontrol panelcausinga strongdelayed
reflectionat the listeningposition

Point Seven Reference Manual

Chapter 2 - Speaker Installation

This kind of speakerplacementalsocouplesacousticenergyfrom the speaker's

cabinet more readily into the console'schassis. Both conditions should be reduced by
placing the speakerson their o.wn standdacoustcally detached,frop, and slightly
behind, the consoleas shown belort. In this locdtion, the reflective:gath off the
console'scontrol panel is now blockedby the meterbridge.

Moving the monitorsto a positionbehindthe meterbridgecauses

the bridgeto block the offendingreflectivepath

Careful consideration shoutd also be glnen to Se physiicelspacing.betweert the

speakers.Alesis recommendsthat tlre distanc.eb.*tueen the speakersequal the
distancebetween the listener and either speaker. In other words, the lisierer and the
two speakersare at the three comers of a triangle havirg equal- length sides. The
Figure below shows this coneept. Note thatboth speakersare turried in somewhat
so that the prime listening position is directly in front of eachspeaker. Applications
that require monitoring by inot'e than one engineer are accommodatedby a smaller
rotation of the cabinets. This will widen the prime listening position somewhat.

The speakersand
listenershouldbe at
the threecornersof
a trianglehaving
equallengthsides

PrimeListeningPosition

Point Seven Reference Manual

 Speaker brstallation - Chapter 2

Alesis has designed the Point Sevens for vertical mounting.

If, however, you need to keep their height profile as low as possible to minimize the
recording engineer's visual obstructions, they may be mounted horizontally. If used
this way, they should be installed with the tweeters towards the outside (see below)

The Point Sevens are completely covered with a non-slip rubber textured laminate
whereas other speakers provide small stick-on pads (or nothing at all) to keep them
from slipping around while they are playing. If you need to move the Point Sevens
or adjust their position slightly, lift them off the mounting surface first rather than
attempting to slide them.

Using The Port Plugs

The low frequency responce of the Point Sevens can be custom tailored by using the
four (supplied) port plugs. If they are used by themselves, without any outside bass
augmentation (i.e. a subwoofer), then the ports should be left open. This will give a
".balanced" sound.
3dB bass boost between 90Hz and 130H2 and result in a

"accurate"
If, however, you want the most sound and are willing to sacrifice bass
response below 100H2, then insert the plugs. This will give slightly less apparmtbass
but the sound will be tighter and very well damped. When used with a subwoofer,
the Point Seven's plugs should always be used. If the ports are left open and a
subwoofer is used, the resulting sound will have a bloated, unnatural midbass.

Point Seven Reference Manual

Chapter 2 - Speaker lnstallation

Fnq 50Fh 100H2

Without port
lvith pon

Connections
Professional grade 5-way gold-plated binding posts are provided for extemal wiring
to the amplifier. This type of cormector can accommodate bare or tirmed wires,
banana plugs and even spade lugs.

About Wire: A lot of hype and confusion exists about the type of speaker wires to
use, most of it created by the wire manufacturers themselves in an effort to have a
unique story to tell. While this expensive wire will not hurt the speaker's perfor-
mance at all, Alesis does not subscribe to most of this hype and chooses to take an
approach based on science when recommmding speaker wire. Our recommendation
is sirnple; use the shortest length of the largest diameter wire you can get. #12-14
gauge multi-stranded speaker wire found at most hi-fi and electronics stores works
very well. This kind of wire resembles oversized lamp cord and is very easy to work
with.

Before connecting the speakers, check that your amplifier is tumed OFF. Be sure
you get the + terminals of the speakers wired to the + terminals of the amplifier. To
help you do this, most speaker cable has a way to tell one conductor from another.
Some use different-colored wires or insulation; others mold a small line or marker
into one insulator to mark it. If one speaker's polarity is out of phase with the other,
the result will be loss of low frequency response and stereo imaging when the system
is played. In most cases, the speaker outputs of the amplifier will have a red terminal
and a black terminal; these should be cortnected to the same-colored terminals of the

Point Seven Reference Manual

 SpeakerInstallation - Chapter 2

Point Seven. Consult the manual of your power amplifier for specific information.
Lr a properly-phased system, a positive input to the amplifier should result in a
positive voltage on the red terminal, and push the driver forward.

If you are using a dual banana plug connector, one side of the plug usually has a
"GND"
marker molded on it so you can keep polarity straight after unplugging and
replugging. In standard practice, the GND side connects to the black terminal of the
speaker.

To connect wires to the teminals if you are not using a banana plug:

1. Strip about 1/2" (15 mm) of insulation from the ends of each wire. If the wire is
stranded, twist the strands together at the end.
2 Tum the red and black terminal caps counter-clockwise until they reach their
limit. As you do, the hole through the terminal post will be exposed.
3. Insert the wires into the holes, observing proper polarity.
4. Tighten the terminal caps so that they hold the wire firmly. Make sure no
insulation is caught inside the terminal, to avoid a loose connection.

Power and Protection

The Point Sevens are rated to handle 50 watts program material. However, an
amplifier with a 100 watt power rating into four ohms, like the Alesis RA-100
Reference Amplifier, is recommended for most monitoring situations. This is because
an amplifier with too little power driven into clipping is far more likely to destoy a
tweeter than a higher powered anp delivering a clean, undistorted signal.

Be sure to veri$ that your amplifier is rated for 4 ohm speakers. Some older
amplifiers are not and may fail if overloaded. Alesis is not responsible for any
failures caused by the use of an inproperly-rated amplifier.Also, there is gq situation
where an amplifier rated beyond 200 watts should ever be used because of the
danger of damaging the Point Seven. To do so is asking for trouble and will void
your waranty.

Alesis does not suggest the use of any extemal protection devices, but considers such
devices as fuses, lamps and/or thermal breakers safe to use, so long as they do not
cause failures or require modifications to the Point Seven's construction which would
void the warranty. Actually, many such devices are generally considered ineffective
and can additionally alter the speaker's sound character, an undesirable trait for a
studio monitor.

The best protection against speaker failure is to mix at a reasonable listening level.

Alesis thanks you for choosing our products. We value any comments you may have
about this monitor system, this manual, your Alesis dealer and about our factory
service. Please take a minute now to fill out your warranty card and tell ur what you
think

Point Seven Reference Manual

 Troubleshooting - Chapter 3

CHAPTER 3

TnouBLEsHoorrNG
Troubleshooting lndex
If you experience problems while using the Point Sevens, please use the following
table to locate possible causes and solutions before contacting Alesis Technical
Support for assistance.

Unfocused sound, bass Check + and - cornections

frequenciesmuddy or from power amp to
missing speakers

Compare to comrnercial CD
of similar sWle: time to

Distorted output lvlake sure nting isbelow

200W crtum downlevd
Damaged speaker Swapspeakersto see if the
comDonents problem bllows the
speaker;if so contact

Maintenance
Cleaning
The cabinet surfaces of the Point Seven are covered with a textured rubber laminate.
Clean these surfaces when necessary with a lint-free cloth dampened in warm soapy
water. To Preserve the textured finistu don't rub hard on the surface. Do not attempt
to clean the cabinet with a brush (which may damage the surface) or a sponge (which
mav leave small crumbs in the texture).

Do not attempt to clean either of the drivers.

The Point Sevens require no periodic maintenance.

Scruice
Before sending the Point Sevens in for repair, make sure they are faulty and that the
problem isn't being caused by something else in the system. Distortion or noise may
be caused by a defective amplifier, preamp, cable, equalizer etc., or a loose
corurection in the system. Connect the Point Sevens to a system that is known to be
working properly to check whether the monitors have malfunctioned.

Point Seven Reference Manual

Chapter9 Troubleshooting

Obtaining Repair Seruice

Before contacting Alesis, check over all your connections, and make sure you've read
the manual.

Customers in the USA and Canada: If the problem persists, caII Alesis USA at 1-80G
S-ALESIS and request the Technical Support deparknent. Talk the problem over with
one of our technicians; if necessary, you will be given a retum order (RO) number
and instructions on how to retum the unit. All units must be shipped prepaid and
COD shipments will not be accepted.

For prompt service, indicate the RO number on the shipping label. Units without an
RO will not be accepted. If you do not have the original packing, ship the NanoVerb
in a sturdy carton, with shock-absorbing materials such as styrofoam pellets (the
kind without CFCs, please) or "bubble-pack" surrounding the unit. Shipping damage
caused by inadequate packing is not covered by the Alesis warranty.

Tape a note to the top of the unit describing the problem, include your name and a
phone number where Alesis can contact you if necessary, as well as instructions on
where you want the product retumed. Alesis will pay for standard one-way shipping
back to you on any repair covered under the terms of this warranty. Next day service
is available for a surcharge.

Field repairs are not normally authorized during the warranty period, and repair
attempts by unqualified personnel may invalidate the warranty.

Service address for customers in the USA:

Alesis Technical Support

3630 Holdrege Avenue
Los Angeles, CA 90015

Cuctomers outside the USA and Canada:

Contact your local Alesis distributor for any warranty assistance. The Alesis Limited
Warranty applies only to products sold to users in the USA and Canada. Customers
outside of the USA and Canada are not covered by this Limited Warranty and may
or may not be covered by an independmt distributor warranty in the country of sale.
Do not retum products to the factory unless you have been given specific instruc-
tions to do so.

Point Seven Reference Manual

 Troubleshooting - Chapter 3

Sp=crFrcATlolus

Drivers: 5.25" non-woven carbon fiber coned

woofer, magnetically shielded
1" ferrofluid cooled silk dome
tweeter, magnetically shielded

Crossovet: 2.0kHz modified third order

Butterworth filter

Frequency Response: 85Hz-27WIz,+3 dB

Power Handling: 50 watts program, 100

watts peak (using EIA-426A method)

Nominal Impedance: 4 ohms

Sensitivity: 86 dB SPL @ L watt/ L meter

Cabinet: Rubber textured laminate over.625" MDF

with molded comer protectors

Dimensions: 7.1"W x Il.2"H x 7.'25"D

Weight Ll lb. each

Point Seven Reference Manual

 ALESIS LIMITED WARR/INTY
ALESIS CORPORATION C'ALESIS) warrants this product to be free of defects in material and
workmanship for a period of ninety (90) days for parts ;nd labor from the date of original retail purchase.
This warranty is enfbrceable only liy the original retail purchaser.
_To be protected by_this warranty, the purchaser must complete and retum the enclosed warranty card
within 14 davs of purchase.
_ During ihe wirranty period ALESIS shall, at its sole and absolute optio4 either repair or replace ftee of
charge any product that proves to be defective on inspection by ALESISoT its authorized service
representative. In all cases disputes conceming this warranty shall be resolved as prescribed by law.
To obtain warranty service, the purchaser must first call or write ALESIS at the address and telephone
number printed below to obtain a Return Authorization Number and instructions conceming wher6 to
retum the unit for service. All inquiries must be accompanied by a description of the problem. All
authorized returns must be sent to ALESIS or an authorized ALESIS repair facility postage prepaid, insured
and properly packaged. Proof of purchase must be presented in the form of a bill of sale, canceled check or
some other positive proof that the product is within the warranty period. ALESIS reserves the right to
update any unit retumed for repair. ALESIS reserves the right to change or improve design of the product
at anv time without orior notice.
fhis warranty does not cover claims for damage due to abuse, neglect, alteration or attempted repair
by unauthorized personnel, and is limited to failures arising during normal use that are due to defects in
material or workmanship in the product.
ANY IMPLIED WARTTANTTES, INCLUDING IMPLIED WARRANTIES OF MERCHANIABILMY
AND FITNESSFORA PARIICULARPURPO6E, ARE LIMITED IN DURATION TOTHE LENGTHOF
THIS LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
IN NO EVENT WILL ALESIS BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES RESUUTING FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY,
INCLUDING, AMONG OTHERTHINGS, DAMAGETOPROPERTY, DAMAGE BASED ON
INCONVENIENCEORON LOSSOF USE OFTHE PRODUCT, ANDTOTHE EXTENT PERMITTEDBY
LAW DAMAGES FOR PERSONAL INIIIRY. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not_apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
This warranty only applies to products sold in the United States of America or Canada. The terms of
this warranty and any'obiigations bf Alesis under this warranty shall apply only within the country of sale.
Without limiting the ioregding, repairs under this warranty shall be made only_by a duly authorized Alesis
servicerepresen-tativeinlhecountyofsale. ForwarrantyinformationinallothercountriesPleasereferto
your local distributor.

ALESIS
3530Holdrege Avenue
Los Angeles,Califomia 90015
1-8M.s-ALESIS
alecom@alesisl.usa.com

Your warantyl will be ln effect

and you will receiye warrantt/ information
OTLY IF YOU SEITD Iil YOUR WARRAilTV GARD

/tlesisCorporatbn
3630HoldregeAwue CA 90016
LosAngebs
PniledlnUSA7-51'12261l/96
SDecilicationsSubjectT0ChangeWithoutNotic€
@l996AlesisCorporation