APPENDIX B INSTALLATION

B.1 Installation Preparation ........................................................... 1

B.1.1 Check Before Installation ................................................... 1
B.1.2 Installation Space............................................................... 2
B.2 IPU Installation........................................................................ 3
B.2.1 Windows Setup .................................................................... 3
B.2.2 Registering Sysmex Account................................................ 5
B.2.3 Security Setting .................................................................... 9
B.2.4 Performance Setting........................................................... 13
B.2.4 Performance Setting........................................................... 13
B.2.5 Appearance Setting ............................................................ 15
B.2.6 IP Address Setting.............................................................. 17
B.2.6 IP Address Setting.............................................................. 18
B.3 XS-IPU Program Installation ................................................. 21
B.4 Main unit Installation ............................................................. 26
B.5 GP/LP Printer Installation and Setting ................................... 30
B.5.1 GP Installation Procedure................................................... 30
B.5.2 LP Installation Procedure ................................................... 32
B.6 XS-IPU Uninstallation (as needed)........................................ 33
B.7 Sampler Installation 10 ......................................................... 35
B.8 Sampler Adjustment at Installation 10 ................................... 49

10 200635

XS series S/M December 13, 2007

APPENDIX B INSTALLATION
B.1 Installation Preparation
B.1.1 Check Before Installation

XS-1000i consists of XS main unit, XS-IPU, XS Supplied Parts and

Sampler Unit. Before installation, confirm that all the components
are contained.

Ambient Temperature:15 to 30°C

Relative Humidity: 45 to 85%
If ambient temperature and relative humidity are not within the range,
air-conditioning should be applied.
Avoid installation in a place where the instrument may be in extremely
high or low temperature.
Avoid installation in a place where the instrument may be exposed to
direct sunlight.
Install in a well-ventilated place.
Avoid installation in a place where instrument may be exposed to
radio interference such as personal computer, centrifuge separator,
wireless radios and communication facility.

Use 3P plug for each power cable.

If the outlet is without grounding, use adapter plug and connect to
ground.

XS series S/M B-1 December 13, 2007

B.1.2 Installation Space

To secure the space required for maintenance, install the IPU on the
right side of the XS main unit. Provide a distance of at least 50cm
behind the instrument.

Width Depth height Weight

Compone
(mm) (mm) (mm) (kg)
nt
(inch) (inch) (inch) l(bs)
305 400 385 Approx. 25
Main Unit
(12.01) (15.75) (15.16) (55.17)
425 200 385 Approx. 10
Sampler
(16.73) (8.87) (15.16) (22.05)

XS-800i

XS-1000i

XS series S/M B-2 December 13, 2007

B.2 IPU InstallationB.2.1 Windows Setup (2) When below screen (product key) appears, enter appropriate
(1) When below screen (personalize your software) appears, enter values.
appropriate names.

XS series S/M B-3 December 13, 2007

(3) When below screen (computer name and administrator password) (4) When below screen (computer domain) appears, select “No”.
appears, enter “IPU” in the name and nothing in the password.

XS series S/M B-4 December 13, 2007

B.2.2 Registering Sysmex Account (2) Select User Accounts.
(1) Select control panel.

XS series S/M B-5 December 13, 2007

(3) Select Create a new account. (4) When below screen appears, enter “sysmex” and click Next.

XS series S/M B-6 December 13, 2007

(5) When below screen appears, select computer administrator and (6) When below screen appears, select sysmex as an account to
click Create Account. change.

XS series S/M B-7 December 13, 2007

(7) When below screen appears, select Create a password. (8) When below screen appears, enter “c, 9, ., 0” in the “Type a new
password” and enter “c, 9, ., 0” in the “Type the new password
again to confirm”. Click Create Password.

XS series S/M B-8 December 13, 2007

B.2.3 Security Setting (2) When below screen appears, click “Change the way Security
(1) Select Security Center in the Control Panel. Center alerts me”.

XS series S/M B-9 December 13, 2007

(3) When below screen appears, unmark all three items and click OK. (4) When below screen appears, click Automatic Updates.

XS series S/M B-10 December 13, 2007

(5) When below screen appears, select Turn off Automatic Updates (6) When below screen appears, click Windows Firewall.
and click OK.

XS series S/M B-11 December 13, 2007

(7) When below screen appears, select Off and click OK.

XS series S/M B-12 December 13, 2007

B.2.4 Performance Setting (2) When below screen appears, select Power Options.

(1) Select Performance and Maintenance.

XS series S/M B-13 December 13, 2007

(3) When below screen appears, select Never on “Never off monitor" (4) When below screen appears, select Do nothing on “When I close
and “Turn off hard disks”. Select Advanced tab. the lid of my portable computer” and “When I press the power
button on my computer”.

XS series S/M B-14 December 13, 2007

B.2.5 Appearance Setting (2) When below screen appears, select Taskbar and Start Menu.

(1) Select appearance and Theme.

XS series S/M B-15 December 13, 2007

(3) When below screen appears, mark Auto-hide the taskbar and (4) In the below screen, click Display.
unmark Hide inactive icons. Click OK.

XS series S/M B-16 December 13, 2007

(5) When below screen appears, select Windows XP in the Theme. (6) When below screen appears, change the Screen resolution to 1024
Select Setting tab. by 768 and Highest (32 bit) in the Color quality. Click OK.

XS series S/M B-17 December 13, 2007

B.2.6 IP Address Setting (2) Click Network and Internet Connections.
(1) Click back at the toolbar in the Appearance and Theme.

When the screen was closed, select start Æ Control Panel.

XS series S/M B-18 December 13, 2007

(3) Click Network and Internet Connections.
(4) When below screen appears, right-click Local Area Connection and
select properties.

XS series S/M B-19 December 13, 2007

 (6) When below screen appears, select Use the following IP address.
(5) When below screen appears, select Show icon in notification area Enter 192.168.28.150 in the IP address. Enter 255.255.255.0 in
when connected. Double-click Internet Protocol (TCP/IP) or click the subnet mask. Click OK.
Double-click Internet Protocol (TCP/IP) and click properties.

(7) Close Local Area Connection Properties by clicking OK.

(8) Click X in upper right to closed network connections.

XS series S/M B-20 December 13, 2007

B.3 XS-IPU Program Installation
NOTE:
This installation must be performed after logon to windows as
“Sysmex” and password as “c9.0”.
When IPU program is running, quit the IPU program by selecting file
( Exit. When confirmation screen appears, click OK.

(1) Set the XS CD-ROM onto the CD-ROM drive.

(2) Contents of the CD appears. When it does not appear, select Start
( My Computer and double-click the CD-ROM icon.）
(3) Double-click the Setup icon.
When below screen appears, click Install/Version Up.

XS series S/M B-21 December 13, 2007

(5) When below screen appears, click Install. (7) Installation starts. If below screen appears, click OK.

(8) When below screen appears, click OK.

(6) When below screen appears, click Yes.

XS series S/M B-22 December 13, 2007

(9) When below screen appears, select XS-1000i or XS-800i according (10) When below screen appears, click OK.
to the instrument to be setup. Enter instrument ID to be installed.
When sampler is connected, mark Sampler Option. Click OK.

XS series S/M B-23 December 13, 2007

(11) When below screen appears, confirm that “Installation has (12) When below screen appears, click Close.
Completed” is displayed and click Close.

XS series S/M B-24 December 13, 2007

(13) When below screen appears, click Close.

XS series S/M B-25 December 13, 2007

 (2) Turn the lock to CCW and open the right side cover.
B.4 Main unit Installation
(1) Remove fixing tape and transportation tape.

Fixing Tape

Transportation
Tape

XS series S/M B-26 December 13, 2007

(3) Remove the clip which fasten the belt. Remove fixing tape for (4) Connect tubing for reagent as follows.
Protection Cover No.174. NOTE: Tubing for CELLPACK must be within 2 meters.

XS series S/M B-27 December 13, 2007

(5) Close main unit right side cover. (15) Turn on main unit and select option as shown when below screen
(6) Connect power cord for the main unit. appears.
(7) Connect the main unit and PC using LAN cable (cross).
(8) Turn on the PC when it is off. Select Exit when IPU program starts.
(9) Select Start Æ Shut Down Æ Log off XS.
(10) Log on to Windows with User name: sysmex and Password: “c”,
“9”, “.”, “0”.
(11) Select Exit when IPU program starts. Set the provided XS
program CD-ROM onto CD-ROM drive.
(12) Start ID Changer in the CD-ROM\TOOLS\ID Changer.
(13) When below screen appears, select XS-1000i/XS-800i, enter S/N
in the New ID (instrument S/N) and select Sampler Option.

(16) When main unit indicator located lower left become green, run
Setting sequence by selecting Controller( Service ( Setting
Sequence. It takes appoximately 24 minutes.
(14) Remove CD-ROM from the CD-ROM drive. Run IPU program by
!
selecting Start Æ All Programs Æ Startup ÆIPU. Log off IPU and
log on IPU with User name: sysmex and Password: “c”, “9”, “.”, “0”.

(17) When Setting Sequence runs, pointer becomes hourglass other

menu could not be selected. When Setting Sequence completes,
the hourglass becomes normal pointer.
(18) Set the Calibration CD-ROM onto CD-ROM drive.
3 EMBED Visio.Drawing.11 4!5

(19) Copy XS-1000i^XXXXX.CAL (XXXXX stands for S/N) in the

XS series S/M B-28 December 13, 2007

 CD-ROM onto C:\Program
Files\Sysmex\IPU\ORG_INI\XS-1000i^XXXXX.CAL with
overwriting it.
(20) Restart the IPU program and run e-CHECK to confirm the data is
within the assay value sheet.

XS series S/M B-29 December 13, 2007

B.5 GP/LP Printer Installation and Setting
B.5.1 GP Installation Procedure
NOTE: On XT-Series instruments, the GP can be also used as
the LP by the initial setting.
Only when the LP is used as a stand-alone, perform LP setting.

(1) Log-on to the Windows as an administrator.

(2) Install the printer driver by following the instruction attached to
the printer.
(3) Select Start Æ Settings Æ Control Panel Æ Printers.
(4) When below screen appears, right-click the printer driver icon
and select properties.

(5) When below window appears,

(5-1) Change the printer name to “GP PRINTER.”
(5-2) Click OK.

XS series S/M B-30 December 13, 2007

 (6) When below window appears,
(6-1) Confirm that the name is GP PRINTER.
(6-2) Click X button to close the window.

(7) Restart the IPU computer.

XS series S/M B-31 December 13, 2007

B.5.2 LP Installation Procedure

(1) Log-on to the Windows as an administrator.

(2) Install the LP referring to the GP Installation Procedure.
(3) Name the printer as “LP PRINTER.”
(4) Open the PRINTDEF.INI file in the C:\Program
Files\Sysmex\IPU folder by notepad.
(5) When below window appears,
(5-1) Change the GP PRINTER at the “Ledger Print” to LP
Printer as shown.
(5-2) Save the file by overwriting it.

(6) Restart the IPU computer.

XS series S/M B-32 December 13, 2007

 B.6 XS-IPU Uninstallation (as needed) (4) When below screen appears, click uninstall.

NOTE:
This uninstallation must be performed after logon to windows as
“Sysmex” and password as “c9.0”.
When IPU program is running, quit the IPU program by selecting file
Æ Exit. When confirmation screen appears, click OK.
When uninstalltion is performed, all files including setting files will be
deleted.

(1) Set the XS CD-ROM onto the CD-ROM drive.

(2) Contents of the CD appears. When it does not appear, select Start
Æ My Computer and double-click the CD-ROM icon.）
(3) Double-click the Setup icon.

XS series S/M B-33 December 13, 2007

(5) When below screen appears, click Execute. (When Database is
needed to be deleted, mark Remove Database Files.)

NOTE: When Database is deleted, all information such as stored data

and history will be deleted.

XS series S/M B-34 December 13, 2007

B.7 Sampler Installation 10 (2) Detach “Position Setting Data” sheet from the inside of the sampler.
(The sheet will be used in B.8 Sampler Adjustment at Installation.)
(1) Remove fixing tapes from the sampler cover.

1
-1

1
00
SU
.11
OP
SN

XS series S/M B-35 December 13, 2007

(3) Remove Trasport Fixing Metal No. 49. (4) Remove fixing tape securing catcher unit.

XS series S/M B-36 December 13, 2007

(5) Remove two clips securing belts. (6) Remove Trasport Fixing Metal No.47.

XS series S/M B-37 December 13, 2007

(7) Remove fixing tape as shown below. (8) Unlock right side cover lock with a slot head screwdriver.
(9) Remove upper cover by loosening two fixing screws (M3X6).

Upper Cover
Fixing Screws

Cover Lock

XS series S/M B-38 December 13, 2007

(10) Remove left side cover by loosening three fixing screws (M3X6) (11) Remove front cover by loosening two fixing screws on the right
and three fixing screws on the left.
(12) Disconnect wiring cord on the innner of the front cover.

XS series S/M B-39 December 13, 2007

(13) Leave the wiring cord attached to the XS Main Unit Front Cover. (14) Pull Sample Set Unit Cover toward you.
(The wiring cord does not need to remove from the XS front cover.
Store them in case of sampler deinstallation.)

XS series S/M B-40 December 13, 2007

 (16) Place the OPSU-11 Base Assy for connecting XS-1000i main unit
(15) Remove Sample Set Unit Cover by removing two fixing screws and sampler.
(Screw P-Tight M 3 X 6 (SUS)) and retract the Sampler Set Unit
into the main unit. (Discard the two fixing screws.)

Sample Set Unit Cover

Fixing Screws

XS series S/M B-41 December 13, 2007

(17) Place XS-1000i main unit onto the base by inserting rubber feet (18) Cut the tie wrap securing wiring cords.
into the holes. When XS-1000i main unit is placed correctly, the
positioning pins are in correct position.

Tie Wrap

XS series S/M B-42 December 13, 2007

(19) Remove dummy cover from the hydraulic connector. (20) Place sampler onto the base as shown below.

XS series S/M B-43 December 13, 2007

(21) Connect six wiring cords.
OPSU-11 (22) Connect one hydraulic connector.

Connect 6 connectors
3675 3677 Stamped wiring cord
3676 LED1_2 No. in Sampler side
ST1 Barcode Reader

Connection table (Nothing is connected to RACK.)

Main Unit Sampler
3672 3686
LED1_2 LED1_2
3671 3675
3673 3677
3674 Barcode
ST1 STI

XS series S/M B-44 December 13, 2007

 (24) Open sampler cover and fix the three fixing screws (M4)
(23) Place wiring cords to your left so that the wiring cords will not be
caught between main unit and sampler. Place the sampler so that
the positioning pins into the holes in the sampler.

M4X6 (348-3926-8)

M4X30 (348-3935-1)

Positioning Pin

XS series S/M B-45 December 13, 2007

(25) Fix the two fixing screws (M3X6: 348-3812-1) onto the sampler (26) Affix main unit chassis and OPSU-11 Base Assy with screw M4X6
right side. (348-3926-8)

M4X6 (348-3926-8)

(27) Attach left side cover by tightening screws.

(28) Attach upper cover by tightening screws.

XS series S/M B-46 December 13, 2007

(28) Attach clear cushion onto upper cover as shown below. (30) Attach OPSU-11 Sample Set Unit Cover (322-3919-7) with
screws M3X4 (348-3911-2).

(29) Close right side cover.

XS series S/M B-47 December 13, 2007

(31) Cover screw tip over the sampler chassis with a urethane rollstock
(368-1577-0).

10 200635

XS series S/M B-48 December 13, 2007

 (3) Select Controller Æ Service Æ Hand Adjustment Æ Pulse Entry
B.8 Sampler Adjustment at Installation 10 and enter values on Position Setting Data removed in step B7 (2).

(1) Select Start Æ All Programs Æ Startup Æ IPU to start IPU program.
Logoff IPU program and logon with logon name “sysmex” and
password “C 9 . 0”.
(2) Turn on the main unit and start up option screen appears. Set
options as follows.

XS series S/M B-49 December 13, 2007

(4) Select Controller Æ Service Æ Tube Holder Adjustment Æ Pulse
Entry and enter values and enter values on Position Setting Data.

10 200635

XS series S/M B-50 December 13, 2007